SECTION 1: SOLAR ELECTRIC (PV) SYSTEM INSTALLATION CHECKLIST

Following the completion of each item on the checklist below, check the box to the left of the item
and insert the date and initials of the person completing the item whether that is the installing
contractor or owner-installer. Remember to follow the proper safety procedures while performing the
system installation. The appropriate safety equipment for each section of the checklist is listed above
each section of the checklist.

Before starting any PV system testing: (hard hat and eye protection recommended)

1. Check that non-current carrying metal parts are grounded properly. (Array frames,
racks, metal boxes, etc. are connected to the grounding system)

2. Ensure that all labels and safety signs specified in the plans are in place.

3. Verify that all disconnect switches (from the main AC disconnect all the way through to
the combiner fuse switches) are in the open position and tag each box with a warning sign to signify
that
work on the PV system is in progress.

PV ARRAY--General (hard hat, gloves, and eye protection recommended)

1. Verify that all combiner fuses are removed and that no voltage is present at the output
of the combiner box.

2. Visually inspect any plug and receptacle connectors between the modules and panels
to ensure they are fully engaged.

3. Check that strain reliefs/cable clamps are properly installed on all cables and cords
by pulling on cables to verify.

4. Check to make sure all panels are attached properly to their mounting brackets
and nothing catches the eye as being abnormal or misaligned.

5. Visually inspect the array for cracked modules.

6. Check to see that all wiring is neat and well supported.

April 2016 http://www.amacoffshoreservices.com/

 PV ARRAY CIRCUIT WIRING (hard hat and eye protection recommended)

1. Check home run wires (from PV modules to combiner box) at DC string combiner box
to ensure there is no voltage on them.

2. Recheck that fuses are removed and all switches are open.

3. Connect the home run wires to the DC string combiner box terminals in the proper
order and make sure labeling is clearly visible.

REPETITIVE SOURCE CIRCUIT STRING WIRING (hard hat, gloves, and eye protection recommended)
The following procedure must be followed for each source circuit string in a systematic approachi.e. east
to west or north to south. Ideal testing conditions are midday on cloudless days March through October.

4. Check open-circuit voltage of each of the panels in the string being wired to verify that it
provides the manufacturers specified voltage in full sun. (Panels under the same sunlight conditions
should have similar voltages--beware of a 20 Volt or more shift under the same sunlight conditions.)

5. Verify that the both the positive and negative string connectors are identified
properly with permanent wire marking.

6. Repeat this sequence for all source circuit strings.

CONTINUATION OF PV ARRAY CIRCUIT WIRING (hard hat, gloves, and eye protection recommended)

7. Recheck that DC Disconnect switch is open and tag is still intact.

8. VERIFY POLARITY OF EACH SOURCE CIRCUIT STRING in the DC String Combiner

Box (place common lead on the negative grounding block and the positive on each string connection--
pay particular attention to make sure there is NEVER a negative measurement). Verify open-circuit
voltage is within proper range according to manufacturers installation manual and number each string
and note string position on as-built drawing. (Voltages should match closely if sunlight is consistent.)

WARNING: IF POLARITY OF ONE SOURCE CIRCUIT STRING IS REVERSED, THIS CAN START A FIRE IN
THE FUSE BLOCK RESULTING IN THE DESTRUCTION OF THE COMBINER BOX AND POSSIBLY
ADJACENT EQUIPMENT. REVERSE POLARITY ON AN INVERTER CAN ALSO CAUSE DAMAGE THAT IS
NOT COVERED UNDER THE EQUIPMENT WARRANTY.

9. Retighten all terminals in the DC String Combiner Box.

April 2016 http://www.amacoffshoreservices.com/

 WIRING TESTS--Remainder of System: (hard hat, gloves, and eye protection recommended)

10. Verify that the only place where the AC neutral is grounded is at the main service panel.

11. Check the AC line voltage at main AC disconnect is within proper limits (115-125
Volts AC for 120 Volts and 230-250 for 240 Volts).

12. If installation contains additional AC disconnect switches repeat the step 11 voltage
check on each switch working from the main service entrance to the inverter AC disconnect switch
closing each switch after the test is made except for the final switch before the inverter (it is possible that
the system only has a single AC switch).

INVERTER STARTUP TESTS (hard hat, gloves, and eye protection recommended)

1. Be sure that the inverter is off before proceeding with this section.

2. Test the continuity of all DC fuses to be installed in the DC string combiner box,
install all string fuses, and close fused switches in combiner box.

3. Check open circuit voltage at DC disconnect switch to ensure it is within proper

limits according to the manufacturers installation manual.

4. If installation contains additional DC disconnect switches repeat the step 4 voltage

check on each switch working from the PV array to the inverter DC disconnect switch closing each
switch after the test is made except for the final switch before the inverter (it is possible that the system
only has a single DC switch).

5. At this point consult the inverter manual and follow proper startup procedure (all
power to the inverter should be off at this time).

6. Confirm that the inverter is operating and record the DC operating voltage in
the following space.

7. Confirm that the operating voltage is within proper limits according to the
manufacturers installation manual.

8. After recording the operating voltage at the inverter close any open boxes related to
the inverter system.

April 2016 http://www.amacoffshoreservices.com/

 9. Confirm that the inverter is producing the expected power output on the supplied meter.

10. Provide the homeowner with the initial startup test report.

SYSTEM ACCEPTANCE TEST (hard hat and eye protection recommended)

Ideal testing conditions are midday on cloudless days March through October. However, this test procedure
accounts for less than ideal conditions and allows acceptance tests to be conducted on sunny winter days.

1. Check to make sure that the PV array is in full sun with no shading whatsoever. If it is
impossible to find a time during the day when the whole array is in full sun, only that portion that is in
full
sun will be able to be accepted.

2. If the system is not operating, turn the system on and allow it to run for 15 minutes
before taking any performance measurements.

3. Obtain solar irradiance measurement by one of two methods and record irradiance on
2 2
this line: W/m . To obtain percentage of peak sun, divide irradiance by 1000 W/m
2 2
and record the value on this line . (example: 692 W/m 1000 W/m = 0.692 or 69.2%.)
Method 1: Take measurement from calibrated solar meter or pyranometer.
Method 2: Place a single, properly operating PV module, of the same model found in the array, in full
sun in the exact same orientation as the array being tested. After 15 minutes of full exposure, test the
short circuit current with a digital multimeter and place that reading on this line: Amps. Divide
this number into the short circuit current (Isc) value printed on the back of the PV module and multiply
2
this number by 1000 W/m and record the value on the line above. (example: Isc-measured = 3.6 Amps;
2 2
Isc-printed on module = 5.2 Amps; Irradiance = 3.6 Amps/5.2 Amps * 1000 W/m = 692 W/m )

4. Sum the total of the module ratings and place that total on this line WattsSTC.
Multiply this number by 0.7 to obtain expected peak AC output and record on this line
WattsAC-estimated.

5. Record AC Watt output from the inverter or system meter and record on this line
WattsAC-measured.

6. Divide WattsAC-measured by percent peak irradiance and record on this line

April 2016 http://www.amacoffshoreservices.com/

 WattsAC-corrected. This AC-corrected value is the rated output of PV system. This number
must be within 90% or higher of WattsAC-estimated recorded in step 4. If it is less than 90%, the PV system
is either shaded, dirty, miswired, fuses are blown, or the modules or inverter are not operating properly.

April 2016 http://www.amacoffshoreservices.com/