Scribd
Upload
203 views

Parallel Circuits

1. A parallel circuit has two or more paths for current to flow through. Voltage is the same across each component, while total resistance is less than any individual branch resistance. 2. The sum of currents through each path equals the total current from the source. Total resistance can be calculated using 1/Rt = 1/R1 + 1/R2 + 1/R3. 3. If one path is broken, current will continue in the remaining paths.

Uploaded by

Angelo Contreras Isla Tayo
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
203 views

Parallel Circuits

1. A parallel circuit has two or more paths for current to flow through. Voltage is the same across each component, while total resistance is less than any individual branch resistance. 2. The sum of currents through each path equals the total current from the source. Total resistance can be calculated using 1/Rt = 1/R1 + 1/R2 + 1/R3. 3. If one path is broken, current will continue in the remaining paths.

Uploaded by

Angelo Contreras Isla Tayo
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 9

Parallel Circuits

A parallel circuit is one that has two


or more paths for the electricity to
flow, the loads are parallel to each
other. If the loads in this circuit were
light bulbs and one blew out, there is
still current flowing to the others
because they are still in a direct path
from the negative to positive
terminals of the battery.

UNDERSTANDING &
CALCULATING
PARALLEL CIRCUITS -
EXPLANATION
A Parallel circuit is one with several
different paths for the electricity to
travel. It's like a river that has been
divided up into smaller streams,
however, all the streams come back
to the same point to form the river
once again.
The parallel circuit has very different
characteristics than a series circuit.
For one, the total resistance of a
Parallel Circuit is NOT equal to the
sum of the resistors (like in a series
circuit). The total resistance in a
parallel circuit is always less than
any of the branch resistances.
Adding more parallel resistances to
the paths causes the total resistance
in the circuit to decrease. As you
add more and more branches to the
circuit the total current will increase
because Ohm's Law states that the
lower the resistance, the higher the
current.

BASIC RULES
A Parallel circuit has certain characteristics and basic
rules:
1. A parallel circuit has two or more paths for current to
flow through.
2. Voltage is the same across each component of the
parallel circuit.
3. The sum of the currents through each path is equal
to the total current that flows from the source.
4. You can find total resistance in a Parallel circuit with
the following formula:
1/Rt = 1/R1 + 1/R2 + 1/R3 +...
Rt = R (t)otal
5. If one of the parallel paths is broken, current will
continue to flow in all the other paths.

1. "A parallel circuit has


two or more paths for
current to flow
through."
Simply remember that PARALLEL
means two paths up to thousands of
paths. The flow of electricity is
divided between each according to
the resistance along each route.

2. "Voltage is the same


across each component
of the parallel circuit."
You may remember from the last
section that the voltage drops across
a resistor in series. Not so with a
parallel circuit. The voltage will be
the same anywhere in the circuit.

3. "The sum of the


currents through each
path is equal to the total
current that flows from
the source."
If one path is drawing 1 amp and the
other is drawing 1 amp then the total
is 2 amps at the source. If there are
4 branches in this same 2 amp
circuit, then one path may draw 1/4A
(.25A), the next 1/4A (.25), the next
1/2A (.5A) and the last 1A.
Don't worry, the next rule will show
you how to figure this out. Simply
remember for now that the branch
currents must be equal to the source
current.
4. "You can find TOTAL
RESISTANCE in a
Parallel circuit with the
following formula: 1/Rt
= 1/R1 + 1/R2 + 1/R3 + ...
"
Before we get into the calculations,
remember what we said at the start
of this section: "The total resistance
of a parallel circuit is NOT equal to
the sum of the resistors (like in a
series circuit).
We will use a parallel circuit with 3
paths as an example (it could be 2, 4
or a 1000 resistors in parallel). The
power source is providing 12 volts
and the value of the resistors are 5
Ohms, 5 Ohms and 2 Ohms.
Let's summize this EXAMPLE:
Voltage = 12V
R1 = 4 Ohm
R2 = 4 Ohm
R3 = 2 Ohm
Remember that "Rt" means Total resistance of the
circuit.
R1, R2, etc. are Resistor one, Resistor two, etc.
Now we will apply the formula above to this example:

1
1 1 1
-
-+-+-
=
R1 R2 R3
Rt

Therefore:

1
1 1 1
-
-+-+-
=
4 4 2
Rt

It is easiest to change the fractions into decimal numbers


(example 1 divide by 4 equals .25):
1/Rt = .25 + .25 + .5
1/Rt = 1
Now you have to get rid of the 1 on the left side so...
Rt = 1/1
Rt = 1 Ohms
NOW, Let's try a more complex one:
Voltage = 12 Volts
R1 = 10 Ohms
R2 = 20 Ohms
R3 = 10 Ohms
R4 = 1 Ohms
1/Rt = 1/10 + 1/20 + 1/10 + 1/1
1/Rt = .1 + .05 + .1 + 1
1/Rt = 1.25
Rt = 1/1.25 = .8 Ohms
Before we move on to the last rule
here's how easy it is to calculate the
amperage through each path using
OHM'S LAW.
In the example we see a 12 and 24
ohm resistor in parallel with a 12 volt
source. First we figure out the total
resistance of the circuit:
1/Rt = 1/12 + 1/24
Rt = 8 Ohms

Now that you know this you can figure out the total
amperage (It) using Ohm's Law:
I total (It) = 12V / 8 Ohms = 1.5 Amps
Therefore the total amperage between the two resistive
paths must equal 1.5 Amps (Rule 3). Now we can figure
out exactly what each path is pulling using Ohm's Law
once more. Remember that the voltage is the same
everywhere in a parallel circuit. So we know the voltage
and the resistance:
I1 = 12V / 12 Ohm = 1 A
I2 = 12V / 24 Ohm = .5 A
We figured the total amperage (It) previously, so now we
can double check if the figures are correct:
I1 + I2 = It
1A + .5A = 1.5A - check

5. "If one of the parallel


paths is broken, current
will continue to flow in
all the other paths."
The best way to illustrate this is also
with a string of light bulbs in
paralallel. If one is burnt out, the
others stay lit.

Reference: https://www.swtc.edu/Ag_Power/electrical/lecture/parallel_circuits.htm

You might also like