Scribd
Upload
224 views

(Abstract) Automatic Railway Gate Controlling

This document describes an automatic railway gate control system using infrared (IR) sensors. The system uses two pairs of IR transmitters and receivers to detect when a train is approaching or leaving the railway crossing. When a train is detected, the microcontroller closes the gate and sounds a siren. It reopens the gate once the second IR pair indicates the entire train has passed through. The system is intended to automate unmanned railway crossings and reduce accidents by automatically controlling the gate based on train detection.

Uploaded by

Nikhith Reddy
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
224 views

(Abstract) Automatic Railway Gate Controlling

This document describes an automatic railway gate control system using infrared (IR) sensors. The system uses two pairs of IR transmitters and receivers to detect when a train is approaching or leaving the railway crossing. When a train is detected, the microcontroller closes the gate and sounds a siren. It reopens the gate once the second IR pair indicates the entire train has passed through. The system is intended to automate unmanned railway crossings and reduce accidents by automatically controlling the gate based on train detection.

Uploaded by

Nikhith Reddy
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

AUTOMATIC RAILWAY GATE CONTROL SYSTEM USING IR

Railways, being the cheapest mode of transportation are preferred over all the other
means. When we go through the daily newspapers, we come across many railway accidents
occurring at unmanned railway crossings. This is mainly due to the carelessness in manual
operations or lack of workers.

In order to overcome these dangerous problems we in this project came up with a


solution for the same. Using simple electronic components we have tried to automate the
control of railway gates. This project is a standalone automatic unmanned railway gate
control system using AT89S52 microcontroller. The main aim of this project is
automating the unmanned railway gate. i.e., the gate is closed automatically whenever the
train arrives and gate is opened after the train leaves the railway - road crossing. The
arrival of train in either direction can be identified using this project. Use of embedded
technology makes this closed loop feedback control system efficient and reliable. Micro
controller (AT89S52) allows dynamic and faster control. Liquid crystal display (LCD)
makes the system user-friendly. AT89S52 micro controller is the heart of the circuit as it
controls all the functions.

The system comprises of two IR Transmitter-Receiver pairs. One IR TX - Rx pair is


located at one end of the railway gate. The second pair is located at another end of the gate.
In each pair the TX and Rx are arranged face to face across the railway track. i.e., TX is
placed at one side of the track and the receiver RX at another side of track. The Rx should
continuously get the signal from the transmitter.
Whenever any train is arriving on the track, the IR signal gets disturbed due to the
interruption of the train. Thus the micro controller identifies the arriving of train. Before
closing the gate the microcontroller gives siren to alert the people who are on the track.
After 30 sec, the controller will close the gate by rotating the stepper motor. For the
opening of the gate, the micro controller should know whether the train has left the
crossing or not. The second IR pair is used for this purpose. The second IR pair identifies the
train since the IR signal gets disturbed when it comes in between TX and RX. The
microcontroller will wait till the last compartment and when it left the IR pair, the receiver
again gets IR signal. Hence the microcontroller knows that the train left the gate. Till this time
the gate is closed. Now, after the train left the crossing, the microcontroller will open the
gate by rotating the stepper motor. LCD displays the status of the train.

This project uses regulated 5V, 500mA power supply. Unregulated 12V DC
is used for geared motor. 7805 three terminal voltage regulator is used for voltage
regulation. Full wave bridge rectifier is used to rectify the ac output of secondary of
230/12V step down transformer.

TECHNICAL SPECIFICATIONS

HARDWARE

Micro controller : AT89X series


Crystal : 11.0592 MHz

LCD : HD44780
IR Transmitters
IR Receivers
Buzzer
DC motor
Power supply
Transformer : 12V step down
Filter : 1000uf/25V
Voltage Regulator : 7805

Software
Keil micro vision
Proteus
UC flash

Applications
Automatic railway gate
Automatic gate opening
Toll gates
Parking areas
BLOCK DIAGRAM

Power
MOTOR
Supply
DRIVER

8
DC MOTOR

IR IR
TRANSMITTER1 5
16X2 LCD
RECEIVER1
1
DISPLAY

IR IR
BUZZER
TRANSMITTER2
POWER SUPPLY BLOCK DIAGRAM
RECEIVER2
Step down Transformer
Bridge Rectifier Filter Regulator Output

You might also like