InteliLiteNT

InteliLite NT MRS
Modular Gen-set Controller

Compact Controller for Single Operating Gen-sets

(IL-NT MRS10/11/15/16 unit)

SW version 1.0, August 2007

User guide

ComAp, spol. s r.o.

Copyright 2007 ComAp s.r.o. Kundratka 2359/17, 180 00 Praha 8, Czech Republic
Written by Eduard Obornk Tel: +420 2 66316661, Fax: +420 2 66316647
Prague, Czech Republic E-mail: [email protected], www.comap.cz
Table of Contents
Table of Contents .................................................................................................................................... 2
General guidelines................................................................................................................................... 5
What describes this manual? .............................................................................................................. 5
!! Warnings !! ....................................................................................................................................... 5
Text ..................................................................................................................................................... 5
General description ................................................................................................................................. 7
Description of the controller system (with all options)......................................................................... 7
What is in the package?...................................................................................................................... 7
IL-NT RS232 communication module ................................................................................................. 7
IL-NT AOU8 gauge driver module ...................................................................................................... 7
IL-NT RD Remote display ................................................................................................................... 7
Remote announciator IGL - RA15....................................................................................................... 7
IG IOM/PTM module ........................................................................................................................... 8
IG-IB Internet bridge............................................................................................................................ 8
IL-NT Terminals....................................................................................................................................... 9
IL-NT Terminals................................................................................................................................... 9
Recommended wiring............................................................................................................................ 10
MRS Wiring Diagram ..................................................................................................................... 10
Getting started ....................................................................................................................................... 11
How to install ..................................................................................................................................... 11
Single phase applications ................................................................................................................. 15
Analog inputs..................................................................................................................................... 16
Extension modules (CAN bus) connection ....................................................................................... 21
Analog outputs .................................................................................................................................. 21
Inputs and outputs ................................................................................................................................. 22
Binary inputs IL-NT - default ............................................................................................................ 22
Binary inputs list ............................................................................................................................. 22
Binary outputs IL-NT MRS16- default .............................................................................................. 24
Binary outputs - list............................................................................................................................ 24
Analog inputs..................................................................................................................................... 30
Setpoints................................................................................................................................................ 32
Password........................................................................................................................................... 32
Basic settings .................................................................................................................................... 32
Engine params .................................................................................................................................. 33
Engine protect ................................................................................................................................... 36
Gener protect .................................................................................................................................... 38
Date/Time.......................................................................................................................................... 40
Sensor spec ...................................................................................................................................... 41
*IOM/PTM module............................................................................................................................. 41
*ECU-controlled engine support............................................................................................................ 43
Values read from ECU ...................................................................................................................... 45
Diagnostic messages read from ECU............................................................................................... 45
Analog inputs..................................................................................................................................... 46
Connection description...................................................................................................................... 47
Sensor specification .............................................................................................................................. 51
Background of the sensor calibration................................................................................................ 51
Default sensor settings...................................................................................................................... 51
Operator interface.................................................................................................................................. 52
Pushbuttons and LEDs, MRS10/11/15/16 ........................................................................................ 52
How to select the gen-set mode ?..................................................................................................... 53
^When to use button GCB ON/OFF? ............................................................................................... 53
Display menus................................................................................................................................... 53
How to view measured data?............................................................................................................ 53
How to view and edit set points? ...................................................................................................... 53
How to find active alarms ? ............................................................................................................... 54

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 2

IL-NT-MRS-1.0.pdf
 MEASUREMENT screens description .............................................................................................. 54
Chart guide to menus and pushbuttons operation ........................................................................... 57
Function description .............................................................................................................................. 58
OFF mode ......................................................................................................................................... 58
MAN mode ........................................................................................................................................ 58
AUT mode ......................................................................................................................................... 59
Alarm management ............................................................................................................................... 60
Sensor fail (FLS) .............................................................................................................................. 60
Warning (WRN) ................................................................................................................................. 60
Shut down (SD)................................................................................................................................. 60
Voltage phase sequence detection................................................................................................... 61
Gen-set operation states ....................................................................................................................... 62
List of possible alarms....................................................................................................................... 62
History file.......................................................................................................................................... 64
Remote control and data logging .......................................................................................................... 65
Direct connection to the PC .............................................................................................................. 65
PC software - LiteEdit ....................................................................................................................... 65
Modbus protocol................................................................................................................................ 65
Remote communication......................................................................................................................... 71
Internet connection............................................................................................................................ 71
Recommended ISDN modem ........................................................................................................... 71
Recommended GSM modem............................................................................................................ 71
Mobile SIM card setting..................................................................................................................... 71
Technical data ....................................................................................................................................... 72
Power supply..................................................................................................................................... 72
Operating conditions ......................................................................................................................... 72
#
Low Temperature modification ........................................................................................................ 72
Dimensions and weight ..................................................................................................................... 73
Generator .......................................................................................................................................... 73
Binary inputs and outputs.................................................................................................................. 73
Analog inputs..................................................................................................................................... 73
Speed pick-up input .......................................................................................................................... 74
D+ function ........................................................................................................................................ 74
*CAN bus interface............................................................................................................................ 74
IL-NT RS232 interface (optional card) .............................................................................................. 74
IL-NT AOUT8 interface (optional card) ............................................................................................. 75
IGS-PTM ........................................................................................................................................... 75
IGL-RA15 .......................................................................................................................................... 75
IG-IB .................................................................................................................................................. 76

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 3

IL-NT-MRS-1.0.pdf
InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 4
IL-NT-MRS-1.0.pdf
General guidelines
What describes this manual?
This manual describes MRS 10/11/15/16 software, which is designed for single set applications.
What is the purpose of the manual?
This manual provides general information how to install and operate InteliLite NT MRS controller.
This manual is dedicated for
Operators of gen-sets
Gen-set control panel builders
For everybody who is concerned with installation, operation and maintenance of the gen-set

!! Warnings !!
Remote control
InteliLiteNT controller can be remotely controlled. In case of the work on the gen-set check, that
nobody can remotely start the engine.
To be sure:
Disconnect remote control via RS232 line
Disconnect input REM START/STOP
or
Disconnect output STARTER and outputs GCB CLOSE/OPEN

Because of large variety of InteliLiteNT parameters settings, it is not possible to describe any
combination. Some of InteliLiteNT functions are subject of changes depend on SW version.
The data in this manual only describes the product and are not warranty of performance or
characteristic.

Text
PAGE (Capital letters in the frame) buttons on the front panel
Break Return (Italic) set points
Generator protections (Bold) Set point group
REMOTE START/STOP (Capital letters) binary inputs and outputs
*Something (Symbol * before text) valid only for IL-NT MRS15/16
^Something (Symbol ^ before text) valid only for IL-NT MRS11/16

Note:
ComAp believes that all information provided herein is correct and reliable and reserves the right to
update at any time. ComAp does not assume any responsibility for its use unless otherwise expressly
undertaken.

Note:
SW and HW must be compatible (e.g. IL-NT-MRS10 firmware and IL-NT MRS10 HW) otherwise the
function wil be disabled. If wrong software is downloaded, message HARDWARE INCOMPATIBLE
appears on controller screen. In this case use Boot load (jumper) programming close Boot jumper
and follow instructions in LiteEdit, download correct software.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 5

IL-NT-MRS-1.0.pdf
 !!! CAUTION !!!
Dangerous voltage
In no case touch the terminals for voltage and current measurement!
Always connect grounding terminals!
In any case do not disconnect InteliLiteNT CT terminals !

Adjust set points

All parameters are preadjusted to their typical values. But the set points in the Basic settings settings
group !!must!! be adjusted before the first startup of the gen-set.
!!! WRONG ADJUSTMENT OF BASIC PARAMETERS
CAN DESTROY THE GEN-SET !!!

The following instructions are for qualified personnel only. To avoid personal injury do
not perform any action not specified in this User guide !!!

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 6

IL-NT-MRS-1.0.pdf
General description
Description of the controller system (with all options)
InteliLiteNT-MRS is a comprehensive controller for single generating sets. IL-NT MRS 15/16 features
extended support of electronic engines and extension modules.
InteliLiteNT controllers are equipped with a powerful graphic display showing icons, symbols and bar-
graphs for intuitive operation, which sets, together with high functionality, new standards in Gen-set
controls.
InteliLite automatically starts the Gen-set, closes the Gen-set C.B. when all conditions are met, then
stops the engine on external signal or by pressing push buttons.
InteliLiteNT provides gas engine support without ventilation.
The key feature of InteliLiteNT is its easy-to-use operation and installation. Predefined configurations
for typical applications are available as well as user-defined configurations for special applications.

What is in the package?

Accessories Description Optional / Obligatory

IL-NT MRS InteliLiteNT central unit Obligatory
IL-NT RS232 RS232 communication card Optional for MRS
IL-NT AOUT8 Gauge driver card Optional for MRS
IL-NT RD Remoted display Optional for MRS
IGL-RA15 Remote annunciator Optional for MRS15/16
IG-IOM/PTM I/O extension module Optional for MRS15/16
IG-IB Internet communication bridge Optional for MRS

IL-NT RS232 communication module

IL-NT RS232 is optional plug-in card to enable InteliLiteNT for RS232 communication. This is required
for computer or Modbus connectin. Card inserts into expansion slot back on the controller.

IL-NT AOU8 gauge driver module

IL-NT AOUT8 is optional plug-in card. Through this card controller can drive up to 8 VDO style
industrial/automotive gauges. Gauge type and value are configured in LiteEdit software. Any analog
value from controller may be shown in that way.

IL-NT RD Remote display

IL-NT RD is remote display for controller. Remote display provides the same control and monitoring
functions as controller itself . No programing of the display is required unit is self configurable from
main controller. It is connected with controller via RS232 line. Longer distances (up to 1200m) are
possible when RS232/RS485 converters are used.

Remote announciator IGL - RA15

The remote announciator IGL-RA15 can be connected to the IL-NT unit via CAN bus. Any of the
binary outputs can be configured (using LiteEdit software) to each LED diode on the RA15. The
module can be also enabled or disabled using LiteEdit software.
See the documentation of RA15 for the technical and function description.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 7

IL-NT-MRS-1.0.pdf
 54 (2,1)
44 (1,7)

106 (4,2)

120 (4,7)
125 (4,9)
~ 25 (1,0)
165 (6,5)

Cutout
~ 75 (3,0)

for Remote Announciator

~ 35 (1,4)
38 (1,5)
40 (1,6)

167 x 108 mm
180 (7,1) (6,6 x 4,3)
185 (7,3)

IG IOM/PTM module

IG-IOM and IGS-PTM modules are I/O extension modules equipped with 8 binary inputs, 8 binary
outputs, 4 analogue inputs and one analogue output. The module can be used for AMF25 only.
Binary inputs and outputs are configurable the same way like inputs and outputs on iL.
Analogue inputs are configurable like iL with the limitation that the binary and tristate mode
can not be used on PTM module.
The protection of analogue IOM/PTM inputs is activated by overcrossing the limits, active only
when the engine is running.
IG-IOM analogue inputs are resistive (the same parameters like IL-NT) 0 -2,4 k. The
module IOM is designed for especially VDO resistive sensors.
IGS-PTM analogue inputs are configurable by jumpers to ranges 0-250, 0-100mV, 0-20mA.
The module can be used especially for Pt100 sensors and current sensors. The module PTM
is not suitable for VDO temperature sensor.

See the documentation of IGS-PTM for the technical and function description.

IG-IB Internet bridge

IG-IB Internet bridge enables InteliLiteNT for Ethernet/Internet communicatons. It is connected to

controller via RS232 line.

See the InteliCommunication guide for further details.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 8

IL-NT-MRS-1.0.pdf
IL-NT Terminals
IL-NT Terminals

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 9

IL-NT-MRS-1.0.pdf
Recommended wiring
MRS Wiring Diagram

Modem or PC
Interface
RS-232C
NOT USED
SPRINKLER
REMOTE OFF
LOAD

+24 V
EMERGENCY STOP
ACCESS LOCK
REMOTE S/S
CONTROL
SIGNALS
ALARM
READY TO LOAD

BINARY OUTPUTS
PRESTART
GEN C.B.
FUEL SOLENOID
Generator C.B.

STARTER
L1

L2

L3

RPM
GENERATOR

OIL PRESSURE

WATER TEMP

FUEL LEVEL
DIESEL/GAS ENGINE

ECU

FUEL SOLENOID

STARTER
- +
D+

BATTERY

Hint:
It is possible to start Volvo and Scania engines via CAN bus. See Engines started via CAN bus.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 10

IL-NT-MRS-1.0.pdf
Getting started
How to install
General
To ensure proper function:
Wiring for binary inputs and analog inputs must not be run with power cables.
Analog and binary inputs should use shielded cables, especially when length >3m.

Power supply
To ensure proper function:
Use min. power supply cable of 1.5mm2
Maximum continuous DC power supply voltage is 36VDC. Maximum allowable power supply voltage
is 39VDC. The InteliLites power supply terminals are protected against large pulse power
disturbances. When there is a potential risk of the controller being subjected to conditions outside its
capabilities, an outside protection devise should be used.
Hint:
The InteliLiteNT controller should be grounded properly in order to protect against lighting strikes!!
The maximum allowable current through the controllers negative terminal is 4A (this is dependent on
binary output load).

For the connections with 12VDC power supply, the InteliLiteNT includes internal capacitors that allow
the controller to continue operation during cranking if the battery voltage dip occurs. If the voltage
before dip is 10V, after 100ms the voltage recovers to 7 V, the controller continues operating. During
this voltage dip the controller screen backlight can turn off and on but the controller keeps operating.
It is possible to further support the controller by connecting the external capacitor and separating
diode:
Relays

D controller
T2A
+ +
-
C
- +
12VDC Battery

The capacitor size depends on required time. It shall be approximately thousands of microFarads.
The capacitor size should be
5 000 microFarad to withstand 150ms voltage dip under following conditions:
Voltage before dip is 12V, after 150ms the voltage recovers to min. allowed voltage, i.e. 8V

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 11

IL-NT-MRS-1.0.pdf
Or by connecting special I-LBA module:
Relays

controller
T2A
+ + +

I-LBA
- - -

- +
12VDC Battery
Note:
I-LBA may not eliminate voltage drop when used with low temperature (-40C) version of controller
and display heating element is on (below 5C). Current drain of heating element exhausts LBA
capacitors very fast .

Power supply fusing

A one-amp fuse should be connected in-line with the battery positive terminal to the controller and
modules. These items should never be connected directly to the starting battery.
Fuse value and type depends on number of connected devices and wire length.
Recommended fuse (not fast) type - T1A. Not fast due to internal capacitors charging during power
up.

+ IL-NT
T1A -

+ -
Battery HUGE
LOADS
STARTER

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 12

IL-NT-MRS-1.0.pdf
Binary output protections
Do not connect binary outputs directly to DC relays without protection diodes, even if they are not
connected directly to controller outputs.

Fuse

Fuse

K1 K2
K1 K2
controller
T1A
+
-
DC relays

- +
24VDC Battery

Grounding
To ensure proper function:
Use as short as possible cable to the grounding point on the switchboard
Use cable min. 2,5mm2
The - terminal of the battery has to be properly grounded

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 13

IL-NT-MRS-1.0.pdf
Magnetic pick-up
To ensure proper function:
Use a shielded cable

MAGNETIC
PICK-UP
iL Signal b

D C
Signal

GAC
Speed Control Unit
ESD 5500
+ -
Power
Supply
- Power
+
Supply

+ -

Battery

Be aware of interference signal from Speed governor when one speed pick-up is used.
If engine will not start:
- Check ground connection from pick-up to controllers, eventually disconnect ground connection
to one of them
- Galvanically separate InteliLite RPM input using ComAp separation transformer RPM-ISO
(1:1)
- Use separate pick-up for Speed governor and InteliLiteNT
Hint:
In some cases the controller will measure a RPM value even though the gen-set is not running:
RPM is measured from the generator voltage (Gear teeth = 0)
IL-NT is measuring some voltage value on input terminals due to open fusing.
If RPM > 0 the controller will be put into a Not ready state and the engine will not be allowed to start.

Current measurement
To ensure proper function
Use cables of 2,5mm2
Use transformers to 5A
Connect CT according to following drawings

K L
L1
k l K L
G L2
k l K L L3
k l
N

COM L1l L2l L3l

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 14

IL-NT-MRS-1.0.pdf
Voltage measurement
L1
L2
G
L3
N
BUS

N L1 L2 L3
GENERATOR
L1
L2
G
L3
BUS

N L1 L2 L3
GENERATOR
Hint:
No separation transformers for three wires voltage connection (without N) are needed.
Switchboard lighting strikes protection according standard regulation is expected !!!

Single phase applications

There is not a separate archive file for single-phase applications. Use standard ail archives.

Recommended wirings
Generator (and mains) single-phase voltage has to be connected to all three-voltage terminals L1, L2
and L3. Generator current has to be connected to L1l and COM terminals only.

Voltage measurement
L
G N

N L1 L2 L3 N L1 L2 L3
GENERATOR MAINS
Hint:
Switchboard lighting strikes protection according standard regulation is expected !!!

Current measurement
To ensure proper function
Use cables of 2,5mm2
Use transformers to 5A
Connect CT according to following drawings. Terminals L2l and L3l are opened.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 15

IL-NT-MRS-1.0.pdf
 K L
G L1
k l
N

COM L1l L2l L3l

Set points adjustment

To run a single-phase application, the following set points have to be set:
Gener protect: Curr unbal to 200 %
Gener protect: Curr unbal del to 60,0 s

Analog inputs
Three analog inputs are available on the IL-NT

Configuration
Each analog input can be configured by LiteEdit software following way.

Analog input item LiteEdit Possibility

Type Type Not used Analog input isnt used
Alarm
Analog input name Name Up to 14 ASCII characters
Config of input Config Analog Analog measuring in specified
range.
Binary (not supp. by PTM) Binary: open/close - threshold
Tri-state (not supp. by PTM) 750 .
Three-state: open/close -
threshold 750 ,
Failure <10 or > 2400
Physical dimension Dim bar,%,C, Up to 3 ASCII characters
(Valid only for analog inputs)
Polarity Contact NC Valid only for binary and three-
type state inputs
NO Valid only for binary and three-
state inputs
Protection direction Protection Over Overstep. Sensor fail does not
activate protection.
Over+Fls Overstep and Sensor fail
activates protection.
Under Under step. Sensor fail does
not activate protection.
Under+Fls Under step and Sensor fail
activates protection.
Sensor characteristic Sensor Curve A IL, IOM,PTM User curve A
Curve B IL, IOM,PTM User curve B
Curve C IL, IOM,PTM User curve C

PT 1000 IL, IOM IEC 751, range -20 to 120 C

NI 1000 IL, IOM DIN 43760, range -20 to 120
VDO Temp IL, IOM C
VDO Press IL, IOM,PTM See chapter sensor
VDO Level IL, IOM,PTM specification
4-20mA/100 IL, IOM 20mA/10.0Bar, ext. R 120
4-20mA/ 60 IL, IOM 20mA/6.0Bar ext R 120

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 16

IL-NT-MRS-1.0.pdf
 Pt100 PTM
Ni100 PTM
0-20mA/100 PTM 0-20mA/10.0Bar
4-20mA/100 PTM 4-20mA/10.0Bar
0-100mV/100 PTM
Decimal points Dec 0, 1, 2 Number of decimal points
(Valid only for analog inputs)

User Curve A, B, C are adjustable in LiteEdit.

Each Analog input has separate set points for two level alarm setting. Analog input alarm levels and
delay adjust in Protection or Engine protection group.

Default current sensor characteristic with external resistor 120 ohms

4-20mA/100 0-20mA/100 0-20mA/-20 -
120C
Primary Converted Note 1 Note 2 Note 3 Note 4
120 0 mA 0% -20C
170 0 0% 4 mA 20% 8C
200 13 22C
230 25 25% 8 mA 40% 36C
280 38 50C
330 50 50% 12 mA 60% 64C
390 63 78C
460 75 75% 16 mA 80% 92C
560 88 106C
690 100 100% 20 mA 100% 120C

Note 1 - % range for 4-20 mA input

Note 2 - range 0-20 mA
Note 3 - % range for 0-20 mA input
Note 4 - characteristic 0-20 mA / -20 - +120 C

Connection of IL-CU analog inputs

- POWER

Standard connection of three resistive sensors

to analog inputs.
AI1
AI2
AI3

3x RESISTIVE
SENSOR

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 17

IL-NT-MRS-1.0.pdf
 - POWER
Three current output sensors connection to
InteliLite.

AI1
AI2
AI3
Set jumpers for current measurement

GND 3x SENSOR
4 - 20 mA

+24V
- POWER

Mixed connection of InteliLite analog inputs:

COM

AI1 binary input

AI1
AI2

AI3

AI2 three state input

AI3 analog resistive input
2x
470

Analog inputs are designed for resistive sensors with resistance in range of 0 to 2,4k.
To ensure a proper function use shielded cables, especially for length over >3m.

Current output transducers

IL-NT analog inputs are mainly designed for resistor sensors.
In special case transducers to 4-20mA output can be used for oil measuring (10.0Bar or 6.0Bar). Use
predefined 4-20mA/100 or 4-20mA/60 sensors.
This method reduces the input resolution by less than 50%. Some types of transducers are not
suitable for connection to InteliLite analog inputs because of influencing by InteliLite analog input.

As binary input
Open, close state are detected, threshold level is 750 .

As three state input

Open, close and failure state are detected. Threshold level is 750 , failure is detected when circuit
resistance is <10 or > 2400 .

Hint:
Protections on binary and three state inputs are following:
IL-NT: AI1 Shutdown IG-IOM: AI1 Shutdown
AI2 Shutdown AI2 Shutdown
AI3 Warning AI3 Shutdown
AI4 Shutdown

Unused analog inputs

Configure Type = Not used

Example of analog input configuration

Configure Oil press input for measuring in Bar, VDO oil pressure sensor, range 0 to 10.0 bars. Alarm
protection level set to 3.5 bars, shut down level 1.2 bars.
Start LiteEdit and select Controller - Configuration Modify Oil Press.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 18

IL-NT-MRS-1.0.pdf
Set configuration for Oil Press analog input:

Type: selection between Not used and Alarm

Not used analog input isnt used
Alarm analog input is used
Set to: Alarm

Config: selection between Analog, Binary Tri-state input.

Analog resistor sensor is connected to Analog input.
Binary open/close contact is connected between Analog input and COM terminal
Analog input detects only open/close state.
Tri-state open/close contact is connected parallel to one of two serial resistors between Analog
input and COM terminal.
Set to: Analog

Dim: Physical dimension of measured value (C, %, Bar, ..) Maximal dimension length is three
characters.
Set to: Bar

Contact type: selection of polarity only when analog input is configured as Binary or Tri-state. When
is analog input configured as analog this setting has no sense.
NC polarity of binary or tri-state input
NO polarity of binary or tri-state input

Sensor: selection of sensor characteristic

Unused input - when Analog input is not used. On the InteliLite screen is displayed #### value, no
alarm is detected.
Curve A User curve A is defined in LiteEdit (default VDO temperature sensor)
Curve B User curve B is defined in LiteEdit (default VDO pressure sensor)
Curve C User curve C is defined in LiteEdit (default VDO fuel level sensor)
Pt1000 PT1000 sensor characteristic according to IEC 751
Ni1000 Ni1000 sensor characteristic according to DIN 43 760
VDO temp VDO temperature sensor
VDO press VDO pressure sensor
VDO level VDO level sensor
4-20mA/60 current output sensor characteristic requires external resistor 120 ohms between
Analog input and COM terminal of Analog inputs
4-20mA/100 current output sensor characteristic requires external resistor 120 ohms between
Analog input and COM terminal
Set to: VDO press

Decimals: setting of number of decimal points of measured value.

0 - e.g. 360 kPa, 100%, 50 C
1 e.g. 3.6 Bar
2- e.g. 0.36 MPa
3 - e.g. 0.366 MPa
Set to: 1

When Analog input configuration is finished set the setpoints Wrn Oil press, Sd Oil press, Oil press del
in Engine protection group.
Each Analog input has separate triplet of setpoints: Wrn level, Sd level, Anl Inp del. Names of these
setpoints are fix defined
Number of decimal points of Wrn level1 and Sd level is the same as the configured number of
decimal points of measured value.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 19

IL-NT-MRS-1.0.pdf
Binary inputs

4k7

iL

+ -
Power
Supply

+ -

Battery

Binary outputs

LOAD

iL

+ -
Power
Supply

+ -

Battery

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 20

IL-NT-MRS-1.0.pdf
Extension modules (CAN bus) connection
H CAN H CAN H CAN H
COM CAN L CAN L CAN L CAN HI

120 ohm
CAN LO

120 ohm
IL-NT L

10 ohm

CAN H
CAN L
CAN H
CAN L

COM
15nF

COM
Engine ECU
EXTENSION
IGS-PTM (optional) IGL-RA15 (optional)
MODULES or
COM (optional)

CAN H
CAN L
9 5

120 ohm

IG-IOM (optional)

Connection rules
CAN bus line must be connected in series, from one unit to the next (no star, no cable stubs, no
branches) both ends must by the 120-ohm (internal or external) resistor terminated. Maximal CAN bus
length is up to 200 meters.

For CAN data cables details see chapter Technical data Communication interface. CAN cable
shielding connect to IL-NT COM terminal.

IL-NT contains internal fix 120-ohm resistor and must be located on the CAN bus end.

New IG-IOM and IGS-PTM units contain internal jumper removable 120-ohm resistor (in older IOM
types are fix resistors). To be sure check resistor presence by ohmmeter. Unit with internal resistor
connect to the end of CAN line.

Following connections are supported (IOM, PTM, ECU order is not important).

IL- NT IG-IOM IGL-RA15 ECU

IL- NT IGS-PTM IGL-RA15 ECU

It is possible to connect only one IG-IOM or IGS-PTM and one IGL-RA15 to IL-NT.

Use button in LiteEdit configuration window to activate CAN (J1939) interface.

Analog outputs
Optional plug in card IL-NT AOU8 provides eigth Pulse-With-Modulation (PWM) outputs. These are
intended to drive VDO style analog gauges. This is to provide visual indication of typically ECU values
without installing aditional sensors on the engine. PWM signal emulates sensor which would be
typically mounted on the engine.
Any value from controler may be configured to the outputs. Use LiteEdit PC SW to configure
coresponding sensor/gauge curve and value selection.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 21

IL-NT-MRS-1.0.pdf
Inputs and outputs
Hint:
Any Binary input or output can be configured to any IL-NT controller terminal or changed to different
function by LiteEdit software. There is fix 1 sec delay when any binary input is configured as
protection.

Binary inputs IL-NT - default

BI1 Rem start/stop
BI2 Access lock
BI3 Emergency stop
BI4 Remote OFF
BI5 Sprinkler
BI6 Not used

Binary inputs list

Not used
Binary input has no function. Use this configuration when Binary input is not connected.

Alarm
If the input is closed (or opened) selected alarm is activated.
Binary Alarm configuration items
Name 14 chararcters ASCII string
Contact type NC Normally closed
NO Normally opened
Alarm type Warning
Shut down
Alarm active All the time
Engine running only

Rem start/stop
External request for engine run. AUT mode only.

Emergency stop
If the input is opened, shut down is immediately activated. Input is inverted (normally closed) in default
configuration.

Hint:
In case of controller hardware or software fail, safe stop of the engine doesnt have to be ensured. To
back-up the Emergency stop function it is recommended to connect separate circuit for disconnection
of Fuel solenoid and Starter signals.

Sprinkler
If the input is closed all alarms are disabled except the binary input EMERGENCY STOP and "engine
overspeed protection".

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 22

IL-NT-MRS-1.0.pdf
 all IL alarms are detected,
IL front panel gen-set RED LED blinks or lights,
alarm is recorded on the IL alarm list screen,
BUT gen-set remains running.

Hint:
Warning SprinklActive is indicated in the AlarmList if sprinkler mode active to inform the operator that
the engine is not protected.

Access lock
If the input is closed, no setpoints can be adjusted from controller front panel and gen-set mode (OFF-
MAN-AUT) cannot be changed.
Hint:
Access lock does not protect setpoints and mode changing from LiteEdit. To avoid unqualified
changes the selected setpoints can be password protected.

Remote OFF
If closed, iL is switched to OFF mode (there are four modes OFF-MAN-AUT-TEST). When opens
controller is switched back to previous mode.
Hint:
This binary input should be connected to schedule timer switch, to avoid start of engine.

Remote MAN
If the input is active, MAN mode is forced to the controller independently on the position of the MODE
selector.

Remote AUT
If the input is active, AUT mode is forced to the controller independently on the position of the MODE
selector. If another of remote inputs is active, then the REMOTE AUT input has the lowest priority.

RemControlLock
If the input is active, setpoints writing or command sending from the external terminal is disabled.

Emergency manual
If the input is activated the controller behaves like when switched to OFF mode. Opens all binary
outputs. There is one exception STOP SOLENOID doesnt activate on this transition.

Detection of "running" engine and subsequent alarm message "Sd Stop fail" is blocked.
The controller shows Emerg Man state and the engine can not be started.
Generator current and power measurement is active in this mode, regardless of the actual state of the
engine.

After the input is open again, the controller recovers to previous state and behaves according to the
actual situation .
Function is active in any controller mode.

StartButton
Binary input has the same function as Start button on the InteliLite front panel. It is active in MAN
mode only.

StopButton
Binary input has the same function as Stop button on the InteliLite front panel. It is active in MAN
mode only.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 23

IL-NT-MRS-1.0.pdf
FaultResButton
Binary input has the same function as Fault reset button on the InteliLite front panel.

HornResButton
Binary input has the same function as Horn reset button on the InteliLite front panel.

^GCB button
Binary input has the same function as GCB button on the InteliLite front panel. It is active in MAN
mode only.

Binary outputs IL-NT MRS16- default

BO1 Starter
BO2 Fuel solenoid
BO3 GCB Close/Open
BO4 Prestart
BO5 Ready to Load
BO6 Alarm

Binary outputs - list

Not used
Output has no function.

Starter
The closed relay energizes the starter motor.
The relay opens if:
the firing speed is reached or
maximum time of cranking is exceeded or
request to stop comes up

Fuel solenoid
Closed output opens the fuel solenoid and enables the engine start.
The output opens if:
EMERGENCY STOP comes or
Cooled gen-set is stopped or
in pause between repeated starts

Stop solenoid
The closed output energizes stop solenoid to stop the engine.
The output is active at least for Stop time, if the stop lasts longer, it stays active until all symptoms say
the engine is stopped.
The engine is stopped if:
RPM < 2 and
Generator voltage < 10V and
Oil pressure < Engine params: StartingPoil.
Hint:

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 24

IL-NT-MRS-1.0.pdf
The engine can be started anytime, if all symptoms say the engine is steady regardless of the fact the
Stop solenoid can still be active (in that case it is deactivated before cranking).

Stop Pulse
Output is active for 1 second after Stop solenoid output activation. This signal is sent to ECU in case
of engine stop request.

Ignition
The output closes after reaching value of CrankRPM, fixed 30RPM. Opens after stopping of the
engine or in pause during repeated start.

Prestart
The output closes prior to the engine start (Prestart) and opens when Starting RPM speed is reached.
During repeated crank attempts the output is closed too.
The output could be used for pre-glow, pre-heat or prelubrication.

Cooling pump
The output closes when gen-set starts and opens Engine params:AfterCool time after stop of the
engine.

Idle/Nominal
The output Idle/Nominal closes after the timer Idle time elapses. The Idle time counter starts to
countdown when Start speed reached. The Underspeed protection is not evaluated during idle period.
A Start fail protection occurs if the RPM drop below 2RPM during idle.

Air valves
Closes together with Prestart. Opens after the engine is stopped.
Stopped engine conditions: RPM = 0, Engine params: Starting Poil, D+ (when enabled).

Alarm
The output closes if :
any warning or shutdown comes up or
the gen-set malfunctions
The output opens if
FAULT RESET is pressed
The output closes again if a new fault comes up.

Horn
The output closes if:
any warning or shutdown comes up or
the gen-set malfunctions
The output opens if:
FAULT RESET is pressed or
HORN RESET is pressed or
Max time of HORN is exceeded (Horn timeout)
The output closes again if a new fault comes up.

GCB Close/Open
MRS11, 16: The output controls the generator circuit breaker.
MRS10 and 15 (GCB no GCB button):
The output closes automatically (in MAN or AUT mode) after engine is started,
MinStabtime elapsed, and generator voltage and frequency is in limits.

GCB on coil
The output activates Generator Circuit Breaker coil.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 25

IL-NT-MRS-1.0.pdf
GCB off coil
The output deactivates Generator Circuit Breaker coil.

GCB UV coil
The output controls Generator Circuit Breaker coil after voltage drop-out.

*AnInIOM1..4 Wrn
Output closes if warning alarm on the appropriate IOM/PTM analog input activates.
The output opens, if
alarm is not active and
FAULT RESET is pressed

*AnInIOM1..4 Sd
Output closes if shutdown alarm on the appropriate IOM/PTM analog input activates.
The output opens, if
alarm is not active and
FAULT RESET is pressed

Ready
The output is closed if following conditions are fulfilled:
Gen-set is not running and
No Shut down or Slow stop alarm is active
Controller is not in OFF mode

Ready to load
The output is closed if genset is running and all electric values are in limits no alarm is active - it is
possible to close GCB or it is already closed. The output opens during cooling state.

Running
Output closes if the engine is in Running state.

Cooling
The output closes when gen-set is in Cooling state.

Supplying load
Closed when the generator current is > 0,5% of the CT ratio.
Exact formulas:
Output is closed when the current at least in one phase is for 1 sec over CT ratio/200+2
Output is opened when the current in all three phases is for 1 sec below CT ratio/200+2
Hint:
Values are truncated after division, not rounded.

Vgen failed
The output closes if the generator over/under voltage shutdown alarm or voltage asymmetry shutdown
alarm activates.
The output opens, if
alarm is not active and
FAULT RESET is pressed

fgen failed
Output closes if the generator over/under frequency shutdown alarm activates.
The output opens, if
alarm is not active and
FAULT RESET is pressed

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 26

IL-NT-MRS-1.0.pdf
Overload
Output closes if the generator overload shutdown alarm activates.
The output opens, if
alarm is not active and
FAULT RESET is pressed

Stop failed
Output closes when the engine has to be stopped, but speed or frequency or voltage or oil pressure is
detected. This protection goes active 60s after stop command.
The output opens, if
alarm is not active and
FAULT RESET is pressed

Overspeed
Output closes if the gen-set over speed alarm activates.
The output opens, if
alarm is not active and
FAULT RESET is pressed

Underspeed
Output closes if the gen-set under speed alarm activates.
The output opens, if
alarm is not active and
FAULT RESET is pressed

Start failed
Output closes after the gen-set start-up fails.
The output opens, if
alarm is not active and
FAULT RESET is pressed

Overcurrent
Output closes if the generator
*IDMT over current or
current unbalance or
short current alarm activates.
The output opens, if
Alarm is not active and
FAULT RESET is pressed

Battery flat
Output closes when iL performs reset during start procedure (probably due to weak battery).
The output opens, if
alarm is not active and
FAULT RESET is pressed

V batt failed
Output closes when battery over/under voltage warning appears.
The output opens, if
alarm is not active and
FAULT RESET is pressed

Oil Press
Output closes if the oil pressure shutdown alarm activates.
The output opens, if

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 27

IL-NT-MRS-1.0.pdf
 alarm is not active and
FAULT RESET is pressed

Oil Press Wrn

Output closes if the oil pressure warning alarm activates.
The output opens, if
alarm is not active and
FAULT RESET is pressed

Water Temp
Output closes if the water temperature shutdown alarm activates.
The output opens, if
alarm is not active and
FAULT RESET is pressed

Water Temp Wrn

Output closes if the water temperature warning alarm activates.
The output opens, if
alarm is not active and
FAULT RESET is pressed

FuelLevel
Output closes if the Fuel level shutdown alarm activates.

FuelLevelWrn
Output closes if the Fuel level warning alarm activates.

Common Wrn
Output closes when any warning alarm appears.
The output opens, if
No warning alarm is active and
FAULT RESET is pressed

Common Sd
Output closes when any shut-down alarm appears.
The output opens, if
No sd alarm is active and
FAULT RESET is pressed

Common Fls
Output closes when any sensor fail alarm appears.
The output opens, if
No warning alarm is active and
FAULT RESET is pressed

OFF mode
The output is closed, if OFF mode is selected.

MAN mode
The output is closed, if MAN mode is selected.

AUT mode
The output is closed, if AUT mode is selected.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 28

IL-NT-MRS-1.0.pdf
ChrgAlternFail
Output closes if gen-set is running and D+ input not energized.
The output opens, if
alarm is not active and
FAULT RESET is pressed
Hint:
Treshhold level for D+ input is 80% supply voltage.

ServiceTime
Output closes if the ServiceTime alarm activates.
The output opens, if
alarm is not active and
FAULT RESET is pressed

ECU CommOK
If the ECU is not communicating and all values from ECU show #### the output is not active. If the
ECU communicates the output is active.

ECU PwrRelay
The output closes at the beginning of prestart and opens if the engine shall be stopped.

ECU YellowLamp
The output copies warning information from ECU.

ECU RedLamp
The output copies shutdown information from ECU.

CtrlHeartBeat
Output signalizes watchdog reset. In a healthy state it blinks at 500ms : 500ms rate. When watchdog
reset occurs, it stops blinking.

ECU CommError
The output is an inversion of binary output ECU CommOK, i.e. the output is closed when ECU is not
communicating and all values from ECU show #####. Communication error causes stop of the engine.

BI1..6 stat
*BI1..8IOM - stat
The outputs give an information about the assigned binary input.
In case the assigned binary input is configured to alarm type, then the output closes when the alarm
activates. It opens if
alarm is not active and
FAULT RESET is pressed

In case the assigned binary input is configured to any control function, the output propagates the state
of the input.

Timer1
Output activates when Timer1 is active. Simultaneously, gen-set is started when is in AUT mode.

Timer2
Output activates when Timer2 is active

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 29

IL-NT-MRS-1.0.pdf
GenParamsOK
The output is copy of generator status LED on iL front panel. The output is closed if genset is running
and all genset electric values are in limits.

Glow plugs
The output closes prior to the engine start (Prestart) and opens when Starting RPM speed is reached.
During repeated crank attempts the output is opened.

Supplying load
Closed when the generator current is > 0,5% of the CT ratio.
Exact formulas:
Output is closed when the current at least in one phase is for 1 sec over CT ratio/200+2
Output is opened when the current in all three phases is for 1 sec below CT ratio/200+2
Hint:
Values are truncated after division, not rounded.

Analog inputs
Three analog inputs are jumper configurable for resistive(default), voltage or current sensor.

It is possible to configure on each Analog input:

Reading from IL Analog inputs or from Engine Control Unit via CAN bus (J1939)
Sensor characteristics from the list, or custom sensor curve
Value dimension (e.g. psi - bars, F - C, % - l)
Number of decimal points (0, 1, 2, ).
Warning and shut-down limits are adjusted in Engine protect group.
The analog inputs are configurable. Use LiteEdit software to modify configuration. Default
configuration is:

Oil press
Oil pressure analog input. Default VDO sensor in range 0 to 10.0 bars.

Water temp
Water temperature analog input. Default VDO sensor in range 0 to 100 C.

Fuel level
Fuel level analog input. Default VDO sensor 0-180R = 0-100%

Hint:
For further information about analog inputs configuration see Analog inputs.

CAN J1939 interface

Following values can be received from Engine Control Unit via CAN bus instead of measuring on IL-
NT terminals when J1939 interface is enabled.

Value Value is received from

J1939 enabled J1939 disabled
RPM ECU IL-NT RPM terminals
Oil pressure ECU or IL-NT AI1 IL-NT AI1 terminals
Water temperature ECU or IL-NT AI2 IL-NT AI2 terminals
Fuel level ECU or IL-NT AI3 IL-NT AI3 terminals
ECU State ECU
Fuel rate ECU
Manifold temp ECU
Boost pressure ECU
PercLoadAtCS ECU

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 30

IL-NT-MRS-1.0.pdf
Use LiteEdit 3.0 to enable/disable J1939 interface and to configure IL-NT analog inputs.
Hint:
RPM reading is automatically switched to pickup or generator voltage measuring (depends on Basic
setting: Gear teeth value) if J1939 fails.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 31

IL-NT-MRS-1.0.pdf
Setpoints
Password
EnterPassword
Password is a four-digit number. Password enables change of relevant protected set points Use or
keys to set and ENTER key to enter the password. There are 3 levels of passwords. Knowledge of
higher password lets you to change setpoint protected by lower password.

ChangePassword
Use or keys to set and ENTER key to change the password.
Hint:
At first the Password has to be entered before the new Password can be changed.

Basic settings
Gen-set name
User defined name, used for InteliLite identification at remote phone or mobile connection.
Gen-set name is max 14 characters long and have to be entered using LiteEdit software.

Nomin power [kW]

Nominal power of the generator
Step: 1kW
Range: 1 32000 kW

Nomin current [A]

It is current limit for generator *IDMT over current and short current protection and means maximal
continuous generator current. See Generator protections: *2Inom del, Ishort setpoints.
Nominal current can be different from generator rated current value.
Step: 1A
Range: 1 - 10000 A

CT Ratio [/5A]
Gen-set phases current transformers ratio.
Step: 1A
Range: 1 5000 A / 5A

PT ratio [/1]
Gen-set potential transformers ratio.
Step: 0,1 V / V
Range: 0,1 500,0 V / V

Nomin voltage [V]

Nominal generator voltage (phase to neutral)
Step: 1V
Range: 80 20000 V

Nominal freq [Hz]

Nominal generator frequency (usually 50 or 60 Hz )
Step: 1Hz
Range: 45 65 Hz

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 32

IL-NT-MRS-1.0.pdf
Gear teeth [-]
Number of teeth on the engine gear for the pick-up.
Set to zero, if no pick-up is used. Engine speed is counted from the generator frequency.
Step: 1
Range: 0 500
Hint:
Generator frequency can be used only when generator voltage (min 5V) is present before reaching of
the firing speed (Starting RPM) after start.

Nominal RPM [RPM]

Nominal engine speed.
Step: 1RPM
Range: 100 4000 RPM

ControllerMode [ OFF, MAN, AUT]

Equivalent to Controller mode changes by MODE or MODE buttons.
Hint:
Controller Mode change can be separately password protected.

FltResGoToMAN [ENABLED/DISABLED]
DISABLED: Controller stays in AUT mode after Fault reset .
ENABLED: Automatic switch from AUT (or TEST) to MAN mode after Fault reset to avoid
automatic engine start. This function is active for Shut down protection only.

DispBaklightTO [min]
Timeout after which the display backlight is switched off.
Step: 1 min
Range: 0 60 min
Default value: 0 means that the display lights all the time

Contr. addr (1 .. 32) [-]

Controller identification number. It is possible to set controller address different from the default value
(1) so that more IL controllers can be interconnected (via RS485) and accessed e.g. from Modbus
terminal.
Hint:
When opening connection to the controller it's address has to correspond with the setting in PC tool.
From LiteEdit it is only possible to connect to controllers with address 1.

*RS232 mode [STANDARD/MODBUS/CumminsMB]

Communication protocol switch.
Standard: LiteEdit communication protocol.
Modbus: Modbus protocol.
CumminsMB: Protocol for communication with Cummins engines via Modbus.

Hint:
For detail description see chapter Modbus protocol.

Engine params
Starting RPM [%]
Firing speed when IL controller stops cranking (starter goes OFF).
Step: 1% of nominal RPM
Range: 5 50 %

Starting POil [Bar]

When reached controller stops cranking (starter goes OFF).

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 33

IL-NT-MRS-1.0.pdf
Step: 0,1 bar
Range: 0,0 10,0
Hint:
There are three conditions for stop cranking: Starting RPM, StartingPOil and D+ (when enabled).
Starter goes off when any of these conditions is vaid.

Prestart time [s]

Time of closing of the PRE-START output prior to the engine start.
Set to zero if you want to leave the output PRE-START open.
Step: 1s
Range: 0 600 s

MaxCrank time [s]

Maximum time limit of cranking.
Step: 1s
Range: 1 60 s

CrnkFail pause [s]

Pause between crank attempts.
Step: 1s
Range: 5 60 s

Crank attemps [-]

Max number of crank attempts.
Step: 1
Range: 1 10

Idle time [s]

Idle time delay starts when RPM exceeds Start RPM . Start fail is detected when during Idle state
RPM decreases below 2.
During the Idle time timer running the binary output IDLE/NOMINAL is opened, when it elapses the
IDLE/NOMINAL output closes. Binary output IDLE/NOMINAL opens during Cooling period again.
Step: 1s
Range: 0 600 s

M
RP
Start RPM
RP
M
RPM = 2

BO Starter

BO IDLE/RATED
Idle time Min stab time
Electric protections
activ e
Start Fail

Hint:
If the IDLE function not supported on the governor, set the Idle time nevertheless to minimum 5s to
avoid Underspeed possibly caused by instability of the engine short after start.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 34

IL-NT-MRS-1.0.pdf
Min stab time [s]
Minimum time after reaching of defined level of RPM to the closing GCB.
Step: 1s
Range: 1 300 (Max stab time) s

Max stab time [s]

Maximum time after start to get proper voltage level of the generator.
Step: 1s
Range: 1 (Min stab time) 300 s
Hint:
When generator voltage within Max stab time does not reach defined limits (Generator protection
group) , an alarm occurs and the genset will shut down

Cooling speed [ NOMINAL / IDLE ]

Selects the function of the Binary output IDLE/NOMINAL during engine Cooling state.
NOMINAL : Cooling is executed at Nominal speed and generator protections are active.
IDLE: Cooling is executed at Idle speed and generator protections are switched off.
Hint:
Binary output IDLE/NOMINAL must be configured and connected to speed governor. Engine Idle
speed must be adjusted on speed governor.

Cooling time [s]

Runtime of the unloaded gen-set to cool the engine before stop.
Step: 1s
Range: 0 3600 s

Stop time [s]

Under normal conditions the engine must certainly stop within this period. The period starts by issuing
stop command.
Step: 1s
Range: 0 240 s
Hint:
Stop of engine is detected when all following conditions are met: RPM <2, Oil pressure < StartingPOil
Generator voltage < 10 VAC and D+ input isnt active.
Stop fail is detected when there is difference between those conditions, e.g RPM<2 and Generator
voltage > 10V.

AfterCool time [s]

Runtime of engine after cooling pump. Binary output Cooling pump is closed when the engine starts
and opens AfterCool time delayed after gen-set stops.
Step: 1s
Range: 0 3600s

Fuel solenoid [ DIESEL / GAS ]

Determines behavior of the Binary output FUEL SOLENOID.
DIESEL: Output closes 1 sec before Binary output STARTER.
The output opens if Emergency stop comes or Cooled gen-set is stopped and in pause
between repeated starts.
GAS: Output closes together with Binary output IGNITION if RPM is over the 30 RPM (fix value).
Output opens after stop command or in pause between repeated start.

D+ function [ENABLED/CHRGFAIL/DISABLED]
ENABLED: The D+ terminal is used for both functions running engine detection and charge fail
detection.
CHRGFAIL: The D+ terminal is used for charge fail detection only
DISABLED: The D+ terminal is not used.
Hint:

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 35

IL-NT-MRS-1.0.pdf
The magnetization current is provided independently on this setpoint value.
The D+ charge fail protection becomes active after Engine params:Idle time reaches zero.

ECU FreqSelect [PRIMARY/SECONDARY/DEFAULT]

This setpoint should be used only for Volvo and Scania engines.

Volvo Volvo Aux is selected in ECU configuration:

Primary or secondary engine speed is set by Frequency select bits in VP Status frame.

Scania Scania S6 Singlespeed is selected in ECU configuration:

Nominal engine speed is chosen by Nominal speed switch 1 and 2 from DLN1 frame when the engine
is running on nominal speed, i.e. binary output Idle/Nominal is active. When the output is not active
(engine is running on Idle speed), the setpoint ECU FreqSelect is not taken into account.

Frequency change for Volvo Penta engines with EMS2

This description refers to the Volvo Penta Application bulletin 30-0-003.
The procedure for changing engine speed on the D9 and D16 engines is different from the D12
engine.
There is no system reset on the EMS2 unit; therefore the procedure is changed.

Procedure if ECU not energized:

1. Switch the IL controller to MAN mode.
2. Power up the ECU.
3. Change the setpoint ECU FreqSelect and confirm it by pressing Enter
4. Press the Stop button on the IL controller.

The whole procedure (step 2 to 4) must not exceed 10 seconds.

Procedure with ECU powered on:

1. Switch the IL controller to MAN mode.
2. Press the Stop button on the IL controller.
3. Change the setpoint ECU FreqSelect and confirm it by pressing Enter
4. Press the Stop button on the IL controller.

The whole procedure (step 2 to 4) must not exceed 10 seconds.

ECU SpeedAdj [%]

Enables to adjust engine speed in ECU via CAN bus. Nominal speed corresponds to 50%.
This setpoint should be used only for Volvo Penta and Scania engines. It has no effect on other
engine brands.
Step: 1%
Range: 0 100%

Engine protect
Eng prot del [s]
During the start of the gen-set, some engine protections have to be blocked (e.g. Oil pressure).
The protections are unblocked after the Protection del time. The time starts after reaching Start RPM.
Step: 1s
Range: 0 300 s

Horn timeout [s]

Max time limit of horn sounding. Set to zero if you want to leave the output HORN open. Horn timeout
starts again from the beginning if a new alarm appears before previous Horn timeout has elapsed.
Step: 1s
Range: 0 600 s

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 36

IL-NT-MRS-1.0.pdf
Overspeed [%]
Threshold for over speed protection
Step: 1% of nominal RPM
Range: 100 150%

AnlInp1 level1 [ Bar]

Warning threshold level for ANALOG INPUT 1
Step: 0,1 bar
Range: -10 1000

AnlInp1 level2 [ Bar]

Shutdown threshold level for ANALOG INPUT 1
Step: 0,1 bar
Range: -10 1000

AnlInp1 del [s]

Delay for ANALOG INPUT 1
Step: 1s
Range: 0 180 s

AnlInp2 level1 []
Warning threshold level for ANALOG INPUT 2
Step: 1 C
Range: -100 10000

AnlInp2 level2 []
Shutdown threshold level for ANALOG INPUT 2
Step: 1 C
Range: -100 10000

AnlInp2 del [s]

Delay for ANALOG INPUT 2 alarm.
Step: 1s
Range: 0 180 s

AnlInp3 level1 []
Warning threshold level for ANALOG INPUT 3
Step: 1%
Range: -100 10000

AnlInp3 level2 []
Shutdown threshold level for ANALOG INPUT 3
Step: 1%
Range: -100 10000

AnlInp3 del [s]

Delay for ANALOG INPUT 3
Step: 1s
Range: 0 180 s

Batt overvolt [V]

Warning threshold for high battery voltage.
Step: 0,1 V
Range: 8(Batt undervolt ) 40 V

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 37

IL-NT-MRS-1.0.pdf
Batt undervolt [V]
Warning threshold for low battery voltage.
Step: 0,1 V
Range: 8V 40 (Batt overvolt)

Batt volt del [s]

Delay for low battery voltage alarm.
Step: 1s
Range: 0 600 s

NextServTime [h]
Counts down when engine running. If reaches zero, an alarm appears.
Step: 1h
Range: 0 65535h

Gener protect
Hint:
All electric protections when activated result in shutdown.

Overload [%]
Threshold for generator overload (in % of Nominal power)
Step: 1% of Nominal power
Range: 0 200%

Overload del [s]

Delay for generator overload alarm.
Step: 0.1s
Range: 0 600.0 s

Ishort [%]
Shutdown occurs when short circuit limit Ishort limit is reached.
Step: 1 % of Nominal current
Range: 100 - 500 %

Ishort del [s]

Delay for generator shorcurrent alarm.
Step: 0.01s
Range: 0.00 10.00 s

*2Inom del [s]

IDMT curve shape selection. 2Inom del is Reaction time of IDMT protection for 200% overcurrent
Igen = 2* Nominal current.
Step: 0,1 s
Range: 0,1 - 60,0 s
IDMT is very inverse generator over current protection. Reaction time is not constant but depends on
generator over current level according following formula.

2Inom del * Nomin current

Reaction time =
Igen - Nomin current

Hint:

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 38

IL-NT-MRS-1.0.pdf
Reaction time is limited up to 900 sec = 15 minutes. IDMT protection is not active for Reaction time
values longer than 15 minutes.

Igen is maximal value of all measured phases of generator current.

EXAMPLE of Reaction time for different over current levels. Values in column 200% are 2Inom del.

Overcurrent
200 % = 100 % 101 % 110 %
2Inom del
0,2 s No action 20 s 2s
Reaction time 2s No action 200 s 20 s
20 s No action No action 200 s
(time > 900 s)

Maximal Reaction time

Reaction time

2Inom del

Igen
Nominal current Ishort

Curr unbal [%]

Threshold for generator current asymmetric (unbalance).
Step: 1% of Nominal current
Range: 1 200% of Nominal current

Curr unbal del [s]

Delay for generator current unbalance
Step: 0.1 s
Range: 0.0 600.0 s

Gen >V Sd [%]

Threshold for generator overvoltage. All three phases are checked. Maximum out of three is used.
Step: 1% of Nominal voltage
Range: 0(Gen <V Sd) 200%

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 39

IL-NT-MRS-1.0.pdf
Gen <V Sd [%]
Threshold for generator undervoltage. All three phases are checked. Minimum out of three is used.
Step: 1% of Nominal voltage
Range: 0% 200 (Gen >V Sd)%

Gen V del [s]

Delay for generator undervoltage and overvoltage alarm
Step: 0.1s
Range: 0.0 600.0 s

Volt unbal [%]

Threshold for generator voltage unbalance alarm.
Step: 1% of Nominal voltage
Range: 0 200% of Nominal voltage

Volt unbal del [s]

Delay for generator voltage unbalance alarm.
Step: 0.1s
Range: 0.0 600.0 s

Gen >f [%]

Threshold for generator phase L3 overfrequency.
Step: 0.1% of Nominal frequency
Range: 0 (Gen <f) 200.0% of Nominal frequency

Gen <f [%]

Threshold for generator phase L3 underfrequency.
Step: 0.1% of Nominal frequency
Range: 0.0 200 (Gen >f ) % of Nominal frequency

Gen f del [s]

Delay for generator underfrequency and overfrequency alarm.
Step: 0.1s
Range: 0.0 600.0 s

Date/Time
Time stamp per [min]
Time interval for periodic history records.
Step: 1 min
Range: 0 200min

#SummerTimeMod [ DISABLED / WINTER / SUMMER,WINTER-S,

SUMMER-S ]
DISABLED: Automatic switching between summer and wintertime is disabled.
WINTER (SUMMER) : Automatic switching between summer and wintertime is enabled and it is set to
winter (summer) season.
WINTER-S (SUMMER-S) : Modification for southern hemisphere.

#Time [HHMMSS]
Actual real time

#Date [DDMMYYYY]
Actual date.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 40

IL-NT-MRS-1.0.pdf
Timer1..2 repeat
[NONE/MONDAY/TUESDAY/WEDNESDAY/THURSDAY/WEDNESDAY/FRI
DAY/SATURDAY/SUNDAY/MON-FRI/MON-SAT/MON-SUN/SAT-SUN]
Defines TIMER1 activation. Binary output TIMER1 is internally linked with Rem Start/Stop binary input.
Refer to binary inputs for details.

NONE: Timer function is disabled

MONDAY, TUESDAY, WEDNESDAY, THURSDAY, WEDNESDAY, FRIDAY, SATURDAY, SUNDAY:
Timer is activated on daily basis.
MON-FRI, MON-SAT, SAT-SUN:
Timer is activated on selected day interval.

Timer1..2 ON time
Day time when Timer output activates.

Timer1..2Duration
Duration of Timer output is active.
Step: 1 min
Range: 1 1440 s

Sensor spec
Calibr AI1,AI2,AI3 []
Calibrating constant to adjust the measured value of IL analog inputs. Physical dimension of
calibrating constant is corresponding to Analog input.
Step: 1
Range: -1000 +1000
Hint:
Calibration constants have to be adjusted when measured value is near the alarm level.
User curves A, B, C can be defined by LiteEdit software.

CalibrAInIOM 1..4 []
Calibrating constant to adjust the measured value of IOM/PTM analog inputs. Physical dimension of
calibrating constant is corresponding to Analog input.
Step: 1
Range: -1000 +1000

*IOM/PTM module
AnlInIOM1..4 lev1 []
The level for IOM ANALOG INPUT 1..4 alarm detection.
Step: 1
Range: -100 - +10000

AnlInIOM1..4 lev2 []
The level for IOM ANALOG INPUT 1..4 alarm detection.
Step: 1
Range: -100 - +10000

AnlInIOM1..4 del [s]

Delay for IOM ANALOG INPUT 1..4 alarm.
Step: 1 s
Range: 0 - 180 s

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 41

IL-NT-MRS-1.0.pdf
Hint:
IG-IOM/IGS-PTM analog inputs protection alarms can be configured following way
Configuration Protection
Under Protection is activated only when measured value is under measured level.
Over Protection is activated only when measured value is over measured level.
Under+fls Level 2 protection is activated by sensor fail as well.
Over+fls Level 2 protection is activated by sensor fail as well.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 42

IL-NT-MRS-1.0.pdf
*ECU-controlled engine support
There exists only one firmware branch for both standard and electronic controlled (monitored)
engines.

Presence of the ECU on the CAN bus/RS232 is configured via LiteEdit like other peripheries (IG-IOM,

IGL-RA15). Pressing the button in Configuration window of LiteEdit (version 2.0 and higher),
opens ECU dialog window where the appropriate engine/ECU type should be selected. There are
three groups of engine/ECU types:

Type selection Supported engine/ECU

Caterpillar EMCP3.1
Caterpillar J1939
Cummins CM570
Cummins MODBUS Cummins engines with Modbus communication support
DDC DDEC IV Detroit Diesel DDEC IV, V
Deutz EMR2
Iveco
Jenbacher Diane
John Deere
Perkins ECM
Scania S6 Singlespeed Scania engines with S6 unit
Scania S6 Singlespeed
Scania engines with S6 unit
newSW
SISU EEM3 gen-set
Standard J1939 engine All other engine brands with J1939 support
Volvo Aux Volvo Penta engines with EMSII, EDCIII units
ECU list Gensets.esl, version 3.4

Hint:
Import latest ECU list Gensets.iwe for up to date engine ECU specification.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 43

IL-NT-MRS-1.0.pdf
If the connected engine is Cummins communicating via RS232, it is necessary to set the setpoint
Basic settings:RS232 mode = CUMMINSMB.

Loss of communication causes shutdown of the running engine. On the contrary, the ECU can be
switched off at quiescent engine, that means not-communicating ECU is in that moment normal
situation. All values from ECU shall show ####, but no alarm is displayed. The output ECU CommOK
follows the real situation, that means it is not active anytime when the ECU does not communicate.

The output ECU PwrRelay closes at the beginning of prestart and opens if the engine shall be
stopped.

The engine is started via standard contact output or via CAN bus (for Volvo and Scania engines). For
other engines J1939 is used for monitoring only.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 44

IL-NT-MRS-1.0.pdf
Values read from ECU
Standard J1939 engines and Scania
When Standard J1939 engines and Scania S6 options are selected, following values are read from
standard J1939 frames:
5.2.1.9 Engine speed (frame 5.3.7 EEC1)
5.2.5.28 Engine oil pressure (frame 5.3.29 Engine Fluid Level/Pressure)
5.2.5.5 Engine coolant temperature (frame 5.3.28 Engine Temperature)
5.2.5.61 Total engine hours (frame 5.3.19 Engine Hours, Revolutions)
5.2.1.7 Percent load at current speed (frame 5.3.6 EEC2)
5.2.5.63 Fuel rate (frame 5.3.32 Fuel Economy)
5.2.5.36 Boost pressure (frame 5.3.36 Inlet/Exhaust Conditions)
5.2.5.4 Intake manifold 1 temperature (frame 5.3.36 Inlet/Exhaust Conditions)

Cummins MODBUS
When Cummins-Modbus option is selected, following values are read from Modbus Register Data
(for QSX15,QSK45, QSK60):
Engine Speed (Register Address:30001)
Oil Pressure (Register Address:30003)
Coolant Temperature (Register Address:30002)
Engine Running Time (Register Address:30008-30009)
Fuel Consumption Rate (Register Address:30018)
Intake Manifold Absolute Pressure (Register Address:30530 (QSK45, QSK60 only))
Intake Manifold Temperature (Register Address:30531 (QSK45, QSK60 only))

Diagnostic messages read from ECU

Diagnostic messages are read and displayed in extra ECU Alarm list. For Standard J1939 SPN
(Suspect Parameter Number), FMI (Failure Mode Identifier) and OC (Occurrence Counter) are shown
together with verbal description if available.
One SPN (Suspect Parameter Number) / FMI (Failure Mode Identify) couple describes one fail
information. If FMI is equal to 0 or 1, WRN is displayed in the ECU Alarm list. For any other FMI
values, FLS is displayed.
Detail SPM/FMI code specification see in:
SAE Truck and Bus Control and Communications Network Standards Manual, SAE HS-1939
Publication
Or refer to corresponding engine manufacturers ECU error codes list.
Following messages are displayed with the description:
SPN:100 EngOil Press
SPN:102 Boost Press
SPN:105 Intake Temp
SPN:110 EngCool Temp
SPN:175 EngOil Temp
SPN:629 Controller#1
SPN:636 PositionSensor
SPN:637 TimingSensor
SPN:651 InjectorCyl#1
SPN:652 InjectorCyl#2
SPN:653 InjectorCyl#3
SPN:654 InjectorCyl#4
SPN:655 InjectorCyl#5
SPN:656 InjectorCyl#6
SPN:677 EngStartRelay
SPN:1485 ECU MainRelay

Hint:
InteliLite controller doesnt support J1587 diagnostic line on Volvo engines. This can cause in some
cases a J1939 alarm message FC:000608 due to missing J1587 bus. Contact your Volvo distributor to
update ECU firmware.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 45

IL-NT-MRS-1.0.pdf
For Scania Fault codes (FC) are displayed. Following messages are available for particular groups of
Fault codes:
FC:1000-1001 Overspeed
FC:1100-1107 EngSpdSensor1
FC:1200-1207 EngSpdSensor2
FC:2000-2002 WtrTempSensor
FC:2100-2102 ChrgAirTmpSens
FC:2200-2202 ChrgAirPrsSens
FC:2400-2403 OilPressSensor
FC:2600-2601 SensorSupply1
FC:2700-2701 SensorSupply2
FC:2800-2802 ExtrAnalogInp
FC:3200-3205 BatteryVoltage
FC:4300-4303 HW Watchdog
FC:6200-6201 FanActuator
FC:6400-6401 WasteGateAct
FC:6600-6601 StarterActuatr
FC:6A00-6A01 ExhaustBrkAct
FC:B000-B001 OilPressProt
FC:B100-B101 CoolantLevProt
FC:B200 OverheatCoolWt
FC:B300 EmergencyStop
FC:C000-C006 PDEInjctorCyl1
FC:C100-C106 PDEInjctorCyl2
FC:C200-C206 PDEInjctorCyl3
FC:C300-C306 PDEInjctorCyl4
FC:C400-C406 PDEInjctorCyl5
FC:C500-C506 PDEInjctorCyl6
FC:C600-C606 PDEInjctorCyl7
FC:C700-C706 PDEInjctorCyl8
FC:E200 OverheatProt
FC:E600 CoordEmergStop

Analog inputs
Reading of mentioned values from ECU enables to use analog inputs of the unit for other purposes,
e.g. measuring, displaying and alarm activation related to various quantities. The configuration thus
allows to use three analog inputs on the central unit and four analog inputs on IG-IOM/IGS-PTM
module if connected.
If the engine without ECU is controlled by InteliLite, the first analog input is permanently configured to
Oil pressure, other analog inputs remain freely configurable.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 46

IL-NT-MRS-1.0.pdf
Connection description
The following diagrams show how to connect the engine control unit to the InteliLite controller:

Engines with J1939 support started via CAN bus

VOLVO PENTA engines (EMS II, EDC III units)

Modem or PC
Interface
RS-232C
NOT USED
SPRINKLER
REMOTE OFF
LOAD

+24 V
EMERGENCY STOP
ACCESS LOCK
REMOTE S/S
CONTROL
SIGNALS

BINARY OUTPUTS
ALARM
READY TO LOAD
PRESTART
GEN C.B.
Generator C.B.

L1

L2

L3

N
GENERATOR

RPM
G

8-pole Deutsch

8 7 6 5 4 3 2 1
DIESEL/GAS ENGINE

connector
ECU

BO ECU PwrRelay
BO ECU CommOK (EDCIII) / ECU CommError (EMSII)

FUEL LEVEL

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 47

IL-NT-MRS-1.0.pdf
SCANIA S6

Modem or PC
Interface
RS-232C
NOT USED
SPRINKLER
REMOTE OFF
LOAD

+24 V
EMERGENCY STOP
ACCESS LOCK
REMOTE S/S
CONTROL
SIGNALS

BINARY OUTPUTS
ALARM
READY TO LOAD
PRESTART
GEN C.B.
Generator C.B.

L1

L2

L3

N
GENERATOR

RPM
G

1 2 3 4 5 6 7 8 9 10
10 -pin EMS B1
DIESEL/GAS ENGINE

connector
ECU

GND

+24 V DC

FUEL LEVEL

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 48

IL-NT-MRS-1.0.pdf
Engines not started via CAN bus

PERKINS 2800 series

IL-NT binary output description Perkins Customer interface connector
Start output connects directly to engine starter solenoid
Fuel output 1,10,15,33,34
powers up ECU and enables the injectors

IL-NT CAN description Perkins Customer interface connector

CAN bus common Screen for the J1939 cable.
CAN bus H 31
CAN bus L 32

JOHN DEERE
IL-NT binary output description John Deere 21 pin Deutsch connector
Start output D
Fuel output G (switched ECU power),J (ignition)

IL-NT CAN description John Deere 21 pin Deutsch connector

CAN bus common Screen for the J1939 cable.
CAN bus H V
CAN bus L U

CUMMINS ISB/ISBE
IL-NT binary output description Cummins ISB OEM Harness connector B
Start output connects directly to engine starter solenoid
Fuel output 39

IL-NT CAN description Cummins ISB 9 pin Deutsch connector

CAN bus common SAE J1939 shield - screen for J1939 cable.
CAN bus H SAE J1939 signal
CAN bus L SAE J1939 return

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 49

IL-NT-MRS-1.0.pdf
Cummins engines with MODBUS communication
InteliLite set up (available from version 2.0):
Basic settings:RS232 mode = CUMMINS MB
Software configuration: ECU ECU engine is connected Type: Cummins MODBUS

RS232/RS485 converter (see following diagram) set up:

Data format settings (SW1) 11 bits (1 start bit, 8 data bits, 2 stop bits)
Baud rate settings (SW2) 9600 bps
(more info available on http://www.advantech.com/products/Model_Detail.asp?model_id=1-D6FLH)

ADAM 4520 RS232/485

CONVERTER
GND DATA1+
RS232
DATA1-
RxD
TxD

10-30
VDC RS485

NOT USED
SPRINKLER
REMOTE OFF
LOAD

+24 V
EMERGENCY STOP
ACCESS LOCK
REMOTE S/S
CONTROL
SIGNALS

ALARM

BINARY OUTPUTS
READY TO LOAD
PRESTART.
GEN C.B.
FUEL SOLENOID
Generator C.B.

STARTER
L1

L2

L3

RPM
GENERATOR

GND (PIN 20)

RS485 - (PIN 18)
CONNECTOR
D-SUB 06

RS485 + (PIN 21)

TERM2 (PIN 19)

DIESEL/GAS ENGINE

ECU

TERM1 (PIN 22)

FUEL SOLENOID

STARTER
- +
D+

BATTERY

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 50

IL-NT-MRS-1.0.pdf
Sensor specification
Background of the sensor calibration
To correct measuring error of each analog input (pressure, temperature, level) calibrating constants
within 10 % of measure range should be set. Three (seven) calibrating constants are set in physical
units - bar, oC, % . From these constants are counted equivalent calibrating resistance which are
internally (in software) add to sensor resistance.
At the moment of calibration (ENTER pressing) is calculated (and in memory saved) calibrating
resistance (in ). This value is added to measured sensor resistance before calculation of the AI1 (AI2
or AI3) value.
Example: iL-NT display Temperature 70 C and real value is 73 C.
After setting Calibr AI1 to +3 C (and pressing ENTER) InteliLite calculates corresponding resistance
(e.g.5) and saves this value into the memory. The resistance is then added to all calculations (e.g.
instead of 70C -> 73C, or e.g. instead of 5C -> 6C).
Hint:
The calibration must be done at the operational point of the analog input (e.g. 80C, 4.0Bar etc..)

Default sensor settings

Analog input 1: 6 points VDO characteristic, pressure measuring in bar
Analog input 2: 10 points VDO characteristic, temperature measuring in C
Analog input 3: 2 points VDO fuel level sensor, 0% = 10, 100% = 180

VDO Pressure sensor

VDO Temperature sensor

200
2000
Resistance [ohm]
Resistance [ohm]

150
1500

1000 100

500 50

0 0
0 20 30 40 50 60 70 80 90 110 0 2 4 6 8 10
Temperature [ C] Pressure [bar]

Temperature Pt 1000 Ni 1000

C ohm ohm
-20 922 893
-10 961 946
0 1000 1000
30 1117 1171
60 1232 1353
80 1309 1483
90 1347 1549
100 1385 1618
110 1423 1688
120 1461 1760

Hint:
When measured value is 6% out of range the Sensor fail FLS is detected.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 51

IL-NT-MRS-1.0.pdf
 Operator interface
Pushbuttons and LEDs, MRS10/11/15/16
Pushbuttons
3 2 1 4
5

15
9

10
16

11

12 8 17

1. MODE Cyclic forward selection the gen-set operation mode (OFF -> MAN -> AUT )
2. MODE Cyclic backward selection the gen-set operation mode (AUT -> MAN ->OFF )
3. HORN RESET Deactivates the HORN
4. FAULT RESET Acknowledges faults and alarms
5. START Start of the gen-set
6. STOP Stop of the gen-set
7.
8. GCB ON/OFF ^Manual open/close of the Generator circuit breaker
9. PAGE Cyclic selection of the display mode(MEASUREMENT->ADJUSTEMENT)
10. Select the set point, select the screen or increase set point value
11. Select the set point, select the screen or decrease set point value
12. ENTER Confirm set point value

LEDs
13.
14.
15. GEN VOLTAGE PRESENT: GREEN LED is on, if gen. voltage is present and within limits
16. GEN-SET FAILURE: RED LED starts flashing when gen-set failure occurs. After FAULT RESET
button is pressed, goes to steady light (if an alarm is still active) or is off (if no alarm is active)
17. ^GCB ON: GREEN LED is on, if GCB is closed. Driven by GCB CLOSE/OPEN output.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 52

IL-NT-MRS-1.0.pdf
How to select the gen-set mode ?
Use MODE or MODE to select requested gen-set operation mode
(OFF MAN AUT)

^When to use button GCB ON/OFF?

In AUT mode this button is disabled.
In MAN mode is enabled, but before closing of a circuit beaker, voltage must be within limits.

Display menus
There are 2 display menus available: MEASUREMENT and ADJUSTMENT
Each menu consists of several screens. Press repeatedly PAGE button to select requested menu.

How to view measured data?

1. Use repeatedly PAGE button to select the MEASUREMENT menu.
2. Use and to select the screen with requested data.

How to view and edit set points?

1. Use repeatedly PAGE button to select the ADJUSTMENT menu.
2. Use or to select requested set points group.
3. Press ENTER to confirm.
4. Use or to select requested set point.
5. Set points marked * are password protected.
6. Press ENTER to edit.
7. Use or to modify the set point. When or is pressed for 2 sec, auto repeat function is
activated.
8. Press ENTER to confirm or PAGE to leave without change.
9. Press PAGE to leave selected set points group.

How to change the display contrast ?

Press ENTER and or at the same time to adjust the best display contrast
Hint:
Only in MEASUREMENT menu.

How to check the serial number and software revision?

Press ENTER and then PAGE. On the display you can see InteliLite INFO screen for 10 seconds.
InteliLite INFO screen contains :
1) Controller name (see Basic setting group)
2) InteliLite serial number (8 character number)
3) SW version: the first is the firmware version number, the second is configuration table
number.
4) Application: MRS16
5) Branch: Standard
Hint:
Only in MEASUREMENT menu.

How to change language?

Press ENTER and then PAGE to get to Serial number and software revision screen. Then press
PAGE to enter Language selection screen. Use or to select desired langue and press ENTER
to confirm selection.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 53

IL-NT-MRS-1.0.pdf
How to find active alarms ?
Active alarm list is the last screen in the MEASUREMENT menu.
Select MEASUREMENT menu. Press You will see the list of all active alarms with the number of
alarms at the top-right corner Three state alarms are introduced:

Description
* Wrn Water temp Active not accepted alarm
Wrn water temp Active accepted alarm
* Wrn Water temp Inactive not accepted alarm
Inactive accepted alarm

Press FAULT RESET accepts all alarms. Non-active alarms immediately disappear from the list.
Active alarm list appears on the screen when a new alarm comes up and Main MEASUREMENT
screen is active.
Hint:
Alarm list does not activate when you are reviewing the values or setpoints.

Second alarm list for ECU alarms is also available. It is displayed one screen above the standard
alarm list on the controller display or under the standard alarm list in Control window of LiteEdit. If an
alarm appears in this alarm list, it is signalized in the standard alarm list and by exclamation mark on
the main measure screen.
Control from the front panel:

One screen up/down

Enter Cursor move within the ECU alarm list
Enter + Fault reset ECU fault code reset

MEASUREMENT screens description

Main measure screen
1 2

3
OFF MAN AUT TEST L
Ready 4
Mains Oper
cos 0.00 7
RPM 0
Timer 0
5
8
6

1. Operation mode of the gen-set

2. Indication of active access lock, Remote OFF or Remote TEST L and alarm !
3. Status of the gen-set
4.
5. RPM of the gen-set
6. Active power
7. Power factor
8. Timer - event s counting time (e.g. prestart, cooling, etc.)

Generator screen
Gen freq

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 54

IL-NT-MRS-1.0.pdf
 Gen V1-2, V2-3, V3-1 ph-ph
Gen V1, V2, V3 ph-N (triple bargraph)
Gen I1, I2, I3 (triple bargraph)

IL-NT Analog inputs screen

Oil pressure (single bargraph)
Water temperature (single bargraph)
Fuel level (single bargraph)
Battery voltage (single bargraph)

IL-NT binary inputs

BI1 to BI6

IL-NT binary outputs

BO1 to BO6

*ECU state
ECU YellowLamp
ECU RedLamp
WaitToStart
Hint:
This screen is shown/hidden depending on whether the ECU is configured or not.

*ECUValues
Oil press
Water temp
PercLoadAtCS
Boost pressure
ManifoldTemp
Fuel rate
Hint:
This screen is shown/hidden depending on whether the ECU is configured or not.

Gen-set power screen

Active power (total and per phase)
Power factor (total and per phase)
React power (total and per phase)
Appar power (total and per phase)

Statistic
Run hours
Number of starts

*Kilowatt-hours kWh (total)

*Reactive power hours kVAh (total only)

NextServTime

Hint:
Running time is measured in complete minutes, displayed in complete hours. Values are stored in
nonvolatile memory.

*ECU AlarmList
Diagnostic messages are read from ECU and displayed in this second alarm list. For Standard J1939
engines SPN (Suspect Parameter Number), FMI (Failure Mode Identifier) and OC (Occurrence
Counter) are shown together with verbal description if available.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 55

IL-NT-MRS-1.0.pdf
Following image shows displaying of ECU alarms in the second alarm list. The additional information
for the row selected by cursor is on the last row (SPN, OC and FMI codes).
If the verbal description of alarm is not available, the SPN (decimal and hexadecimal) is displayed.

EngOilPress WRN
BoostPress FLS
EngOilTemp FLS
629(275h) FLS
Controller#1
EngCoolTemp WRN
_____________________
SPN:110 OC:7 FMI:3

Hint:
For FMI = 0 and 1, WRN is displayed. For other FMI codes, FLS is displayed.

Alarm list

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 56

IL-NT-MRS-1.0.pdf
Chart guide to menus and pushbuttons operation

PAGE

PAGE

Measure Screens Par. Edit Screens

OFF MAN AUTO
500 ENGINE BASIC
ENGINE PROT
0 1000 GEN BASIC
GEN PROTECT
12345h MAINS FAIL
586 kW 14:23:15

PAGE ENTER

GEAR TEETH
150 150 -

Next NOM RPM

1500
START RPM
1500 RPM

Screen 30
CRANK TIME
10
30%

10s

Parameter setting:

1. Set cursor by buttons

2. Press ENTER
to editing mode

3. Adjust parameter by buttons

Next 4. Press ENTER

to write parameter into memory
Screen Press PAGE to cancel of editing mode

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 57

IL-NT-MRS-1.0.pdf
Function description
OFF mode
No start of the gen-set is possible. Outputs STARTER, GCB CLOSE/OPEN and FUEL SOLENOID are
not energized.
No reaction if buttons START,STOP,^GCB ON/OFF are pressed.

MAN mode
START. - starts the gen-set.
^GCB ON/OFF
The controller closes GCB.
The controller opens GCB when closed.
If the generator voltage is out of the limits, the controller does not to respond to the GCB
ON/OFF

STOP stops the gen-set.

Hint:
The engine can run without load unlimited time.
The controller does not automatically stop the running gen-set in MAN mode.
The controller does not start the gen-set when binary input REM START/STOP is closed.

Start-stop sequence (simplified)

MODE = MAN (Engine start/stop request is given by pressing buttons START and STOP )
MODE = AUT (Engine start/stop request is given by binary input REM START/STOP)
State Condition of the transition Action Next state
Ready Start request PRESTART on Prestart
Prestart time counter
started
RPM > 2 or Oil pressure detected or Gen Stop (Stop fail)
voltage > 10V or D+ is active

OFF mode selected or Shut down alarm Not Ready

active
Not Ready RPM < 2, Oil pressure not detected, Vgen Ready
< 10V, D+ not Active, no shutdown alarm
active, other than OFF mode selected

Prestart 3 Prestart time elapsed STARTER on Cranking

FUEL SOLENOID on4
MaxCrank time counter
started
Cranking 3 RPM> Start RPM STARTER off Starting
PRESTART off

D+ input activated for 1s or oil pressure STARTER off Cranking

detected or Gen voltage > 25% Vgnom PRESTART off

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 58

IL-NT-MRS-1.0.pdf
State Condition of the transition Action Next state
MaxCrank time elapsed, 1st attempt STARTER off Crank pause
FUEL SOLENOID off
STOP SOLENOID on
CrankFail pause timer
started
MaxCrank time elapsed, last attempt STARTER off Shutdown (Start
PRESTART off fail)
Crank CrankFail pause elapsed STARTER on Cranking
pause 3 FUEL SOLENOID on4
STOP SOLENOID off
MaxCrank time counter
started
Starting 3 80% Nominal speed reached READY TO LOAD on 1 Running
Min, MaxStabTime
counter started
RPM = 0 or any other shutdown condition FUEL SOLENOID off Shutdown
STOP SOLENOID on
60 sec. Elapsed FUEL SOLENOID off Shutdown (Start
STOP SOLENOID on fail)
Running Stop request READY TO LOAD off Cooling
Cooling time timer started
RPM = 0 or any other shutdown condition READY TO LOAD off 2 Shutdown
FUEL SOLENOID off
GCB CLOSE/OPEN closed Loaded
Loaded GCB CLOSE/OPEN opened Running
RPM = 0 or any other shutdown condition FUEL SOLENOID off Shutdown
STOP SOLENOID on
READY TO LOAD off
Cooling Cooling time elapsed FUEL SOLENOID off Stop
STOP SOLENOID on
RPM = 0 or any other shutdown condition FUEL SOLENOID off Shutdown
STOP SOLENOID on
Start request READY TO LOAD on 1 Running
Stop RPM = 0, Oil pressure not detected, Vgen < Ready
10V, D+ not active
60 sec. Elapsed Stop (Stop fail)

1
if all generator parameters OK and MinStab Time elapsed, indicates that GCB is possible to close.
In AUT mode closes in this moment GCB automatically.
2
If GCB output used GCB opens automatically
3
The start-up sequence can be interrupted in any time by comming stop request
4
Fuel solenoid is switched on with time advance of 1s fixed before starter motor is switched on.

Hint:
Treshhold level for D+ input is 80% supply voltage, activation delay is 1s (to override short firings
during during cranking for example in cold conditions).

AUT mode

The controller does not respond to buttons START, STOP, GCB ON/OFF. Engine start/stop request
is given by binary input REM START/STOP.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 59

IL-NT-MRS-1.0.pdf
Alarm management
Following alarms are available:
Sensor fail
Warning
Shut down

Sensor fail (FLS)

Sensor fail is detected when measured value is 6% out of selected sensor characteristic. Sensor fail is
indicated by ##### symbol instead measured value.

Warning (WRN)
When warning comes up, only alarm outputs and common warning output are closed.

Possible warnings:
See List of possible events

Shut down (SD)

When the shut-down alarm comes up, InteliLite opens outputs GCB CLOSE/OPEN, FUEL
SOLENOID, STARTER and PRESTART to stop the engine immediately. Alarm outputs and common
shutdown output are closed. Active or not reset protection disables start.

Possible shut-down alarms:

See List of possible events

Alarm time chart

Idle time Gen >U, <U, >f, <f

5 sec Underspeed

Protection "Engine running only" protections, engine

delay water temperature luboil pressure

"All the time" configured protections, I >, I >>, RPM >>, mains failure detection
nominal speed

GCB opened
Switched to

GCB closed
Starter OFF

Max stab time

Min stab time
Start

Stop

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 60

IL-NT-MRS-1.0.pdf
Voltage phase sequence detection
InteliLite controller detects phase sequence on generator voltage terminals. This protection is
important after controller installation to avoid wrong voltage phases phase connection. Following
alarms can be detected:

Wrong phase sequence

There is fix defined phase sequence in InteliLite controller L1, L2, L3. When the phases are
connected in different order (e.g. L1,L3,L2 or L2,L1,L3) following alarms are detected:
G ph opposed = wrong generator phase sequence

Inverted phase polarity

inverted phase polarity can be detected due to wrong connection of separation transformers between
controller and generator / mains / bus voltage. Phase sequence is OK but some phase(s) is connected
in opposite way (180 shift).
Following alarms can be detected:
GEN L1 neg = generator phase L1 is inverted
GEN L2 neg = generator phase L2 is inverted
GEN L3 neg = generator phase L3 is inverted

Wrong phase sequence and inverted polarity

It is combination of both previous alarms
G ph+L1 neg = wrong generator phase sequence and phase L1 is inverted
G ph+L2 neg = wrong generator phase sequence and phase L2 is inverted
G ph+L3 neg = wrong generator phase sequence and phase L3 is inverted

Hint:
Phase sequence detection is active when voltage in all three phases is >50VAC and all phases angles
are in the range 120 20.
Phase sequence alarm detection is 1 sec delayed to avoid transient effects.

Sensor fail detection

Sensor fail Fls is detected when measured value is 6 percent out of range. Controller screen displays
in this case string #### instead measured value.

R1

R2

R3

R4
R5

Sensor -6% Range of measurement +6% Sensor

100%
Failure Range of sensor Failure

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 61

IL-NT-MRS-1.0.pdf
Gen-set operation states
Engine state machine
Init Autotest during controller power on
Not ready Genset is not ready to start
Prestart Prestart sequence in process, Prestart output is closed
Cranking Engine is cranking
Pause Pause between start attempts
Starting Starting speed is reached and the Idle timer is running
Running Genset is running at nominal speed
Loaded Genset is running at nominal speed and GCB OPEN/CLOSE is closed
Stop Stop
Shutdown Shut-down alarm activated
Ready Genset is ready to run
Cooling Genset is cooling before stop
EmergMan Emergency Manual gen-set operation
AFterCool Engine aftercooling, CoolingPump output is closed

Electric state machine

MinStabTO Minimal Stabilization Timeout

MaxStabTO Maximal Stabilization Timeout
FwRet Brk Forward return break delay. Delay between GCB opening and MCB closing

List of possible alarms

Information on binary
Protection
Events specification output available (See Description
type
list of Binary outputs)
Oil Press Wrn WRN YES Oil pressure is smaller than Wrn Oil
press setpoint.
Oil Press Sd SD NO Oil pressure is smaller than Sd Oil
press setpoint.
Engine Temp Wrn WRN YES Water temperature is greater than
Wrn Water temp setpoint.
Engine Temp Sd SD NO Water temperature is greater than Sd
Water temp setpoint.
Fuel Level Wrn WRN YES Fuel level is smaller than Wrn Fuel
Level setpoint.
Fuel Level Sd SD NO Fuel level is smaller than Sd Fuel
Level setpoint.
Ubat WRN YES Battery voltage is out of limits given by
Batt overvolt and Batt undervolt
setpoints.
AnInIOM Wrn WRN YES Warning alarm configurable on the
input of IG-IOM/IGS-PTM.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 62

IL-NT-MRS-1.0.pdf
 Information on binary
Protection
Events specification output available (See Description
type
list of Binary outputs)
AnInIOM Sd SD YES Shutdown alarm configurable on the
input of IG-IOM/IGS-PTM.
Binary input Configurable YES Configurable Warning/Shutdown
alarms on the inputs of IL-NT.
Battery flat SD YES If the controller switches off during
starting sequence due to bad battery
condition it doesnt try to start again
and activates this protection.
Start failed SD YES Gen-set start failed.
ParamFail NONE NO Wrong checksum of parameters.
Happends typically after downloading
new firmware or changing of the
parameter. The controller stays in
INIT mode. Check all parameters,
write at least one new parameter.
Vgen <, > SD YES The generator voltage is out of limits
given by Gen <V and Gen >V
setpoints.
Vgen unbl SD NO The generator voltage is unbalanced
more than the value of Volt unbal
setpoint.
Fgen <,> SD YES The generator frequency is out of
limits given by Gen >f and Gen <f
setpoints.
Igen unbl SD NO The generator current is unbalanced.
Overload SD YES The load is greater than the value
given by Overload setpoint.
Overspeed SD YES The protection comes active if the
speed is greater than Overspeed
setpoint.
Underspeed SD YES During starting of the engine when the
RPM reache the value of Starting
RPM setpoint the starter is switched
off and the speed of the engine can
drop under Start RPM again. Then the
Underspeed protection becomes
active. Protection evaluation starts 5
seconds after reaching StartingRPM.
EmergencyStop SD NO If the input Emergency stop is opened
shutdown is immediately activated.
GCB fail SD NO Failure of generator circuit breaker.
PickupFault SD NO Failure of magnetic pick-up sensor for
speed measurement.
Stop fail SD YES Gen-set stop failed.
WrnServiceTime WRN NO The period for servicing is set by the
NextServTime setpoint. The
protection comes active if the running
hours of the engine reach this value.
ChrgAlternFail WRN YES Failure of alternator for charging the
battery.
SprinklActive WRN NO The protection is active if the output
Sprinkler is closed.
*Wrn RA15 fail WRN NO Warning alarm in case of lost
connection to IGL-RA15 module.
*Sd IOM fail SD NO Shutdown alarm in case of lost
connection to IG-IOM/IGS-PTM

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 63

IL-NT-MRS-1.0.pdf
 Information on binary
Protection
Events specification output available (See Description
type
list of Binary outputs)
module.
Wrn ECU Alarm WRN NO ECU alarm list is not empty
Low BackupBatt WRN NO RTC backup battery is flat

History file
InteliLite NT stores a record of each important event into the history file. The history file seats 117
records. When the history file is full, the oldest records are removed.
Hint:
To force history download in LiteEdit (direct,,modem or Internet) open History window and select
History | Read history command.

Record structure
Abbreviation Historical value
Num Number of historical event
Reason Event specification
Date Date of historical event in format DD/MM/YY
Time Time of historical event in format HH:MM:SS
RPM Engine speed
Pwr Generator active power
PF Generator PF
LChr Character of the load
Gfrq Generator frequency
Vg1 Generator voltage L1
Vg2 Generator voltage L2
Vg3 Generator voltage L3
Ig1 Generator current L1
Ig2 Generator current L2
Ig3 Generator current L3
UBat Battery voltage
OilP IL-NT Analog input 1 value ( default Oil pressure)
EngT IL-NT Analog input 2 value ( default Water temperature)
FLvl IL-NT Analog input 3 value ( default Fuel level)
AIM1 IG-IOM, IGS-PTM Analog input 1 value (when configured IG-IOM, IGS-PTM)
AIM2 IG-IOM, IGS-PTM Analog input 2 value (when configured IG-IOM, IGS-PTM)
AIM3 IG-IOM, IGS-PTM Analog input 3 value (when configured IG-IOM, IGS-PTM)
AIM4 IG-IOM, IGS-PTM Analog input 4 value (when configured IG-IOM, IGS-PTM)
BIN Binary inputs IL-NT
BIM IG-IOM, IGS-PTM Binary inputs (when configured IG-IOM, IGS-PTM)
BOUT Binary inputs IL-NT
BOM IG-IOM, IGS-PTM Binary outputs (when configured IG-IOM, IGS-PTM)
FC ECU alarm FailureCode
FMI ECUalarm Failure Mode Identifier

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 64

IL-NT-MRS-1.0.pdf
Remote control and data logging
Direct connection to the PC
InteliLite can be connected directly with PC via optional IL-NT RS232 interface.
Use the standard serial cable to connect PC with InteliLite.

Hint:
Make sure the grounding system on controller and PC COM port (negative of the PC DC supply) are
identical before the first direct connection. There must not be any voltage between these two points
otherwise the internal reversible fuse in controller burns out. The simple solution is to assure, that the
PC supply 240/20V is ground free (GND terminal is not connected).

PC CONTROLLER

2 - RxD 2 - RxD

RS232
RS 232
RS232

3 - TxD 3 - TxD
230 VAC 5 - GND 5 - GND

Required the same

voltage potential
between GNDs

0 VDC
- +
Battery

PC software - LiteEdit
On the PC (for direct or modem connection) has to be installed the ComAps software package
LiteEdit. (based on Windows 95 or newer platform)
LiteEdit enables:
read the quantities
adjust all set points
control the engine
configure the controller
select software configuration
modify alarm inputs and outputs
modify password, commands protections
direct, modem or Internet communication

Modbus protocol

The selection of the function of IL serial port is done via the setpoint RS232 mode in Basic settings

9600 bps, 8 data bits, 1 stop bit, no parity

Transfer mode RTU
Function 3 (Read Multiply Registers)
Function 6 (Write Single Register)
Function 16 (Write Multiply Registers)
The response to an incoming message is sent with minimum 4.096 ms delay after message
reception

The complete description of Modbus communication protocol can be found in Modbus Protocol
Reference Guide PI-MBUS-300 and Open Modbus Specification Release 1.0. Both documents are
available from web site at http://www.modicon.com/openmbus/ .

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 65

IL-NT-MRS-1.0.pdf
Communication object vs. Register
All the data intended for communication has its representation as communication objects in the
controller. The communication object is represented by the n-byte array in the controller memory and
identified by the unique 16-bit communication object number. The register, according to Modbus
communication protocol, represents a two-byte data and in communication functions is referenced by
16-bit register address. Further in the description of communication functions the communication
object number will always be used as a register address and length of the communication object
will be expressed by number of registers. Just one communication object can be read or written
by one communication function.

Hint:
To obtain communication object numbers it is possible to download the actual controller description
on-line from controller or from (ail) archive and use export data function from LiteEdit software.

Communication object list (exported from default IL-NT-MRS16 archive)

Setpoints (MRS16):
Ser.
Name Firmware ver. Application Date App. ver. num. Filename
IL-NT-
IL-NT-1.0 MRS16-
IL-NT R:26.07.2007 MRS16 14.8.2007 1,0 1234567 1.0.AIL

Com. High
Group Name Value Dimension Password obj. Low limit limit Data type

Basic settings Gen-set name IL-NT 0 8637 Short string

Basic settings Nomin power 200 kW 0 8276 1 32000 Unsigned 16
Basic settings Nomin current 350 A 0 8275 1 10000 Unsigned 16
Basic settings CT ratio 2000 /5A 0 8274 1 5000 Unsigned 16
Basic settings PT ratio 1,0 /1 0 9579 0,1 500,0 Unsigned 16
Basic settings Nomin voltage 231 V 0 8277 80 20000 Unsigned 16
Basic settings Nominal freq 50 Hz 0 8278 45 65 Unsigned 16
Basic settings Gear teeth 120 0 8252 0 500 Unsigned 16
Basic settings Nominal RPM 1500 RPM 0 8253 100 4000 Unsigned 16
Basic settings ControllerMode OFF 0 8315 String list
Basic settings FltResGoToMAN DISABLED 0 9983 String list
Basic settings DispBaklightTO 15 min 0 10121 0 241 Unsigned 8
Basic settings Contr. addr 1 3 24537 1 32 Unsigned 8
Basic settings RS232 mode STANDARD 3 24522 String list

Engine params Starting RPM 25 % 0 8254 5 50 Unsigned 8

Engine params Starting POil 4,5 Bar 0 9681 0,0 10,0 Integer 16
Engine params Prestart time 2 s 0 8394 0 600 Unsigned 16
Engine params MaxCrank time 5 s 0 8256 1 60 Unsigned 8
Engine params CrnkFail pause 8 s 0 8257 5 60 Unsigned 8
Engine params Crank attempts 3 0 8255 1 10 Unsigned 8
Engine params Idle time 12 s 0 9097 0 600 Unsigned 16
Engine params Min stab time 2 s 0 8259 1 10 Unsigned 16
Engine params Max stab time 10 s 0 8313 2 300 Unsigned 16
Engine params Cooling speed NOMINAL 0 10046 String list

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 66

IL-NT-MRS-1.0.pdf
 Engine params Cooling time 30 s 0 8258 0 3600 Unsigned 16
Engine params AfterCool time 180 s 0 8662 0 3600 Unsigned 16
Engine params Stop time 60 s 0 9815 0 240 Unsigned 16
Engine params Fuel solenoid DIESEL 0 9100 String list
Engine params D+ function DISABLED 0 9683 String list
Engine params ECU FreqSelect DEFAULT 0 10266 String list
Engine params ECU SpeedAdj 50 % 0 9948 0 100 Unsigned 16

Engine protect Eng prot del 5 s 0 8262 0 300 Unsigned 16

Engine protect Horn timeout 10 s 0 8264 0 600 Unsigned 16
Engine protect Overspeed 115 % 0 8263 50 150 Unsigned 16
Engine protect AnlInp1 level1 2,0 Bar 0 8369 -10,0 1000,0 Integer 16
Engine protect AnlInp1 level2 1,0 Bar 0 8370 -10,0 1000,0 Integer 16
Engine protect AnlInp1 del 3 s 0 8365 0 180 Unsigned 16
Engine protect AnlInp2 level1 80 C 0 8375 -100 10000 Integer 16
Engine protect AnlInp2 level2 90 C 0 8376 -100 10000 Integer 16
Engine protect AnlInp2 del 5 s 0 8371 0 180 Unsigned 16
Engine protect AnlInp3 level1 20 % 0 8381 -100 10000 Integer 16
Engine protect AnlInp3 level2 10 % 0 8382 -100 10000 Integer 16
Engine protect AnlInp3 del 10 s 0 8377 0 180 Unsigned 16
Engine protect Batt overvolt 36,0 V 0 9587 18,0 40,0 Integer 16
Engine protect Batt undervolt 18,0 V 0 8387 8,0 36,0 Integer 16
Engine protect Batt volt del 5 s 0 8383 0 600 Unsigned 16
Engine protect NextServTime 65534 h 0 9648 0 65535 Unsigned 16

Gener protect Overload 120 % 0 8280 0 200 Unsigned 16

Gener protect Overload del 5,0 s 0 8281 0,0 600,0 Unsigned 16
Gener protect Ishort 250 % 0 8282 100 500 Unsigned 16
Gener protect Ishort del 0,00 s 0 9991 0,00 10,00 Unsigned 16
Gener protect 2Inom del 4,0 s 0 8283 1,0 60,0 Unsigned 16
Gener protect Curr unbal 50 % 0 8284 1 200 Unsigned 16
Gener protect Curr unbal del 5,0 s 0 8285 0,0 600,0 Unsigned 16
Gener protect Gen >V Sd 110 % 0 8291 70 200 Unsigned 16
Gener protect Gen <V Sd 70 % 0 8293 0 110 Unsigned 16
Gener protect Gen V del 3,0 s 0 8292 0,0 600,0 Unsigned 16
Gener protect Volt unbal 10 % 0 8288 1 200 Unsigned 16
Gener protect Volt unbal del 3,0 s 0 8289 0,0 600,0 Unsigned 16
Gener protect Gen >f 110,0 % 0 8296 85,0 200,0 Unsigned 16
Gener protect Gen <f 85,0 % 0 8298 0,0 110,0 Unsigned 16
Gener protect Gen f del 3,0 s 0 8297 0,0 600,0 Unsigned 16

Date/Time Time stamp per 60 min 0 8979 0 240 Unsigned 8

Date/Time SummerTimeMod DISABLED 0 8727 String list
Date/Time Time 0:00:00 0 24554 Time

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 67

IL-NT-MRS-1.0.pdf
 Date/Time Date 1.1.2006 0 24553 Date
Date/Time Timer1 repeat NONE 0 10045 String list
Date/Time Timer1 ON time 5:00:00 0 10042 Time
Date/Time Timer1Duration 5 min 0 10044 1 1440 Unsigned 16
Date/Time Timer2 repeat NONE 0 10202 String list
Date/Time Timer2 ON time 5:00:00 0 10199 Time
Date/Time Timer2Duration 5 min 0 10201 1 1440 Unsigned 16

Sensors spec Calibr AI 1 0,0 Bar 0 8431 -100,0 100,0 Integer 16

Sensors spec Calibr AI 2 0 C 0 8407 -1000 1000 Integer 16
Sensors spec Calibr AI 3 0 % 0 8467 -1000 1000 Integer 16
Sensors spec CalibrAInIOM 1 0 U4 0 8793 -1000 1000 Integer 16
Sensors spec CalibrAInIOM 2 0 U5 0 8794 -1000 1000 Integer 16
Sensors spec CalibrAInIOM 3 0 U6 0 8795 -1000 1000 Integer 16
Sensors spec CalibrAInIOM 4 0 U7 0 8796 -1000 1000 Integer 16

IOM/PTM
module AnlInIOM1 lev1 0 U4 0 8762 -100 10000 Integer 16
IOM/PTM
module AnlInIOM1 lev2 0 U4 0 8766 -100 10000 Integer 16
IOM/PTM
module AnlInIOM1 del 5 s 0 8770 0 180 Unsigned 16
IOM/PTM
module AnlInIOM2 lev1 0 U5 0 8763 -100 10000 Integer 16
IOM/PTM
module AnlInIOM2 lev2 0 U5 0 8767 -100 10000 Integer 16
IOM/PTM
module AnlInIOM2 del 5 s 0 8771 0 180 Unsigned 16
IOM/PTM
module AnlInIOM3 lev1 0 U6 0 8764 -100 10000 Integer 16
IOM/PTM
module AnlInIOM3 lev2 0 U6 0 8768 -100 10000 Integer 16
IOM/PTM
module AnlInIOM3 del 5 s 0 8772 0 180 Unsigned 16
IOM/PTM
module AnlInIOM4 lev1 0 U7 0 8765 -100 10000 Integer 16
IOM/PTM
module AnlInIOM4 lev2 0 U7 0 8769 -100 10000 Integer 16
IOM/PTM
module AnlInIOM4 del 5 s 0 8773 0 180 Unsigned 16

Values (MRS16):
Name Firmware ver. Application Date App. ver. Ser. num.
IL-NT IL-NT-1.0 R:26.07.2007 MRS16 14.8.2007 1,0 12345678

Group Name Value Dimension Com. obj. Data type

Engine params ECU State [010] 10034 Binary 8

Engine params Fuel rate 0,0 L/h 9860 Unsigned 16
Engine params Water temp 22 C 9855 Integer 16
Engine params ManifoldTemp 20 C 9878 Integer 16
Engine params Oil Pressure 0,0 Bar 10354 Integer 16
Engine params Boost pressure 0,0 Bar 9877 Unsigned 8
Engine params PercLoadAtCS 0 % 9925 Unsigned 8

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 68

IL-NT-MRS-1.0.pdf
 Engine values RPM 1500 RPM 8209 Unsigned 16

Statistics kWhours 0 kWh 8205 Integer 32

Statistics kVArhrs 0 kVAh 8539 Integer 32
Statistics Run hrs 0 h 8206 Integer 32
Statistics Num starts 0 8207 Unsigned 16
Statistics NextServTime ##### h 9648 Unsigned 16
Statistics E-Stop 0 11195 Unsigned 32
Statistics ShutDown 0 11196 Unsigned 32

Analog CU Ubat 24,3 V 8213 Integer 16

Analog CU CPU temp 37,1 C 10124 Integer 16
Analog CU D+ 5,7 V 10603 Integer 16
Analog CU Oil Pressure 15,6 Bar 8227 Integer 16
Analog CU Engine Temp 50 C 8228 Integer 16
Analog CU Fuel level 99 % 8229 Integer 16

Generator Act power 150 kW 8202 Integer 16

Generator Act pwr L1 50 kW 8524 Integer 16
Generator Act pwr L2 50 kW 8525 Integer 16
Generator Act pwr L3 50 kW 8526 Integer 16
Generator React pwr 15 kVAr 8203 Integer 16
Generator React pwr L1 5 kVAr 8527 Integer 16
Generator React pwr L2 5 kVAr 8528 Integer 16
Generator React pwr L3 5 kVAr 8529 Integer 16
Generator Appar pwr 153 kVA 8565 Integer 16
Generator Appar pwr L1 51 kVA 8530 Integer 16
Generator Appar pwr L2 51 kVA 8531 Integer 16
Generator Appar pwr L3 51 kVA 8532 Integer 16
Generator Pwr factor 1,00 8204 Integer 8
Generator Load char R 8395 Char
Generator Pwr factor L1 1,00 8533 Integer 8
Generator Load char L1 R 8626 Char
Generator Pwr factor L2 1,00 8534 Integer 8
Generator Load char L2 R 8627 Char
Generator Pwr factor L3 1,00 8535 Integer 8
Generator Load char L3 R 8628 Char
Generator Gen freq 50,0 Hz 8210 Unsigned 16
Generator Gen V L1-N 230 V 8192 Unsigned 16
Generator Gen V L2-N 230 V 8193 Unsigned 16
Generator Gen V L3-N 230 V 8194 Unsigned 16
Generator Gen V L1-L2 398 V 9628 Unsigned 16
Generator Gen V L2-L3 398 V 9629 Unsigned 16

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 69

IL-NT-MRS-1.0.pdf
 Generator Gen V L3-L1 398 V 9630 Unsigned 16
Generator Gen curr L1 41 A 8198 Unsigned 16
Generator Gen curr L2 41 A 8199 Unsigned 16
Generator Gen curr L3 41 A 8200 Unsigned 16

Binary I/O BIN [1111001] 8235 Binary 16

Binary I/O BInpIOM [01000110] 8602 Binary 16
Binary I/O BOUT [111100] 8239 Binary 16
Binary I/O BOutRA15 [100010010000000] 9849 Binary 16
Binary I/O BOutIOM [11011001] 8604 Binary 16

Date/Time Time ##### 24554 Time

Date/Time Date ##### 24553 Date

IL info Engine state ##### 8330 Unsigned 16

IL info Breaker state ##### 8455 Unsigned 16
IL info Timer text ##### 8954 Unsigned 16
IL info Timer val 0 s 8955 Unsigned 16
IL info SW version 0,0 8393 Unsigned 8
IL info Application 4 8480 Unsigned 8
IL info SW branch 1 8707 Unsigned 8
IL info PasswordDecode ##### 9090 Unsigned 32

IOM/PTM module AnInIOM 1 10 U4 8978 Integer 16

IOM/PTM module AnInIOM 2 20 U5 8759 Integer 16
IOM/PTM module AnInIOM 3 30 U6 8760 Integer 16
IOM/PTM module AnInIOM 4 40 U7 8761 Integer 16
1
In case of software malfunction DiagData shows the value that enables to locate possible bug in
software. Include this number when reporting a software problem.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 70

IL-NT-MRS-1.0.pdf
Remote communication
Note:
Refer to InteliCommunication guide for all additional information.

Internet connection
IL-NT controllers can be monitored from LiteEdit 3.0 over the Internet using Internet Bridge (IG-IB)
connected to the controller RS232 port.

Recommended ISDN modem

Askey TAS-200E
ASUScom TA-220ST
Develo Microlink ISDN i

Recommended GSM modem

Siemens M20, TC35, TC35i, ES75, MC39
Wavecom M1200/WMOD2
Wavecom - Maestro 20, dual 900/1800MHz.
Wavecom Fastrack M1306B, dual 900/1800 MHz (Fastrack M1206B is NOT recommended)
FALCOM A2D, dual 900/1800MHz.

GSM Modem setup

Prior to start work with GSM modem run following program for GSM proper setup.
Program writes all the necessary AT commands to configure the GSM modem properly for use with IL-
NT.
This program runs independent on LiteEdit:
Start MS Windows-Start-Program files - LiteEdit Gm_setup.exe.
Select COM port
Select iG-CU (=IS-CU) or iG-MU unit
Press Setup button
Follow commands in GSM Modem Setup window

Typical real baud rate for GSM data communication is 80 to 90 Bps.

Hint:
It is strongly recommended to use the same type of modem on the both sides (IL and PC) of
connection.

Analog Analog GSM GSM

modem modem or modem modem

Mobile SIM card setting

Adjust SIM card in GSM modem following way:
enable data connection (when required)
no PIN code

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 71

IL-NT-MRS-1.0.pdf
Technical data
Power supply
Voltage supply 8-36V DC
Consumption 40-430mA depend on supply voltage and temperature

Consumption depends on supply voltage 0,104A at 8VDC

0,080A at 12VDC
0,051A at 24VDC
0,044A at 30VDC
0,040A at 36VDC

Allowed supply voltage drop-out: 100ms from min. 10V, return to min. 8V
Battery voltage measurement tolerance 2 % at 24V

Hint:
For the supply voltage less than 7V the backlight of the display is switched off.
Short-term voltage drops (e.g. during the engine cranking) do not affect the operation at all.

Operating conditions
Operating temperature IL-NT -20..+70oC
Operating temperature IL-NT LT# -40..+70oC
Storage temperature -30..+80oC
Protection front panel IP65
Humidity 95% without condensation
Standard conformity
Low Voltage Directive EN 61010-1:95 +A1:97
Electromagnetic Compatibility EN 50081-1:94, EN 50081-2:96
EN 50082-1:99, EN 50082-2:97
Vibration 5 - 25 Hz, 1,6mm
25 - 100 Hz, a = 4 g
Shocks a = 200 m/s2

#
Low Temperature modification
LCD display limits controller operating temperature range to 20 oC - + 70 oC even if the other
electronic components work in wider temperature range.

Internal preheating foil is mounted in InteliLiteNT LT to extend display operational temperature range.
Preheating starts at temperature below 5 oC and preheating power depends on temperature and
power supply voltage.

Technical data
IL-NT Standard Order code:IL-NT-xxxxx LT
Operating temperature -20 oC..+70oC -40 oC..+70oC
Storage temperature -30 oC..+80oC -30 oC..+80oC

Preheating foil increases controller current consumption

Controller No preheating Preheating at ambient temperature

consumption at 0 oC -20 oC -40 oC
12VDC 80 mA +75 mA +210 mA +325 mA
24VDC 51 mA +31 mA +100 mA +175 mA

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 72

IL-NT-MRS-1.0.pdf
InteliLite LT works immediately after switch on at -30 oC and display becomes visible after a few
minutes.

Dimensions and weight

Dimensions 180x120x55mm
Weight 450g

Generator
Nominal frequency 50-60Hz
Frequency measurement tolerance 0,2Hz

Current inputs
Nominal input current (from CT) 5A
Load (CT output impedance) < 0,1
CT input burden < 0,2 VA per phase (In=5A)
Max. measured current from CT 10 A
Current measurement tolerance 2% from the Nominal current
Max. peak current from CT 150 A / 1s
Max. continuous current 12 A

Voltage inputs
Measuring voltage range 0 277 VAC phase to neutral
0 480 VAC phase to phase
Maximal measured voltage 340 VAC phase to neutral
600 VAC phase to phase
Input resistance 0.6 M phase to phase
0.3 M phase to neutral
Voltage measurement tolerance 2 % from the Nominal voltage
Overvoltage class III / 2 (EN61010)

Binary inputs and outputs

Binary inputs
Number of inputs 7
Input resistance 4,2 k
Input range 0-36 VDC
Switching voltage level for close contact indication 0-2 V
Max voltage level for open contact indication 8-36 V

Binary open collector outputs

Number of outputs 7
Maximum current 0,5 A
Maximum switching voltage 36 VDC

Analog inputs
Not electrically separated
Number of inputs 3
Resolution 10 bits
Jumper selectable range V, Ohm(default), mA
Maximal resistance range 2500
Maximal voltage range 2.5 V
Current range 0 20 mA
Input impedance 180 for mA measuring
Input impedance > 100 k for V measuring
Resistance measurement tolerance 2 % 2 out of measured value
Voltage measurement tolerance 1 % 1mV out of measured value

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 73

IL-NT-MRS-1.0.pdf
Current measurement tolerance 2.5 % 0,5mA out of measured value

Speed pick-up input

Type of sensor magnetic pick-up (connection by shielded cable is
recommended)
Minimum input voltage 2 Vpk-pk (from 4 Hz to 4 kHz)
Maximum input voltage 50 Veff
Minimum measured frequency 4 Hz
Maximum measured frequency 10 kHz (min. input voltage 6Vpk-pk)
Frequency measurement tolerance 0,2 %

D+ function
Max. D+ output current 300 mA
Guaranteed level for signal Charging OK 80% of supply voltage

*CAN bus interface

Galvanically separated
Maximal CAN bus length 200m
Speed 250kBd
Nominal impedance 120
Cable type twisted pair (shielded)

Following dynamic cable parameters are important especially for maximal 200 meters CAN bus length
and 32 iS-COM units connected:
Nominal Velocity of Propagation min. 75% (max. 4,4 ns/m)
Wire crosscut min.0,25 mm2
Maximal attenuation (at 1 MHz) 2 dB / 100m

Recommended Industrial Automation & Process Control Cables:

BELDEN (see http://www.belden.com):
3082A DeviceBus for Allen-Bradley DeviceNet
3083A DeviceBus for Allen-Bradley DeviceNet
3086A DeviceBus for Honeywell SDS
3087A DeviceBus for Honeywell SDS
3084A DeviceBus for Allen-Bradley DeviceNet
3085A DeviceBus for Allen-Bradley DeviceNet
3105A Paired EIA Industrial RS485 cable

LAPP CABLE (see http://www.lappcable.com)

Unitronic BUS DeviceNet Trunk Cable
Unitronic BUS DeviceNet Drop Cable
Unitronic BUS CAN
Unitronic-FD BUS P CAN UL/CSA

IL-NT RS232 interface (optional card)

Plugs into IL-NT controller COMMUNICATIN MODULE port.

Maximal distance 10m

Speed 19.2kBd (STD) 9.6kBd (MODBUS)

Recommend external converter:

ADVANTECH ADAM 4520: RS232 to RS422/485 converter, DIN rail, automatic RS485 bus
supervision, no external data flow control signals, galvanic isolated.

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 74

IL-NT-MRS-1.0.pdf
Recommended internal converter:
ADVANTECH PCL-745B or PCL745S : Dual port RS422/485 Interface card, automatic RS485 bus
supervision, no external data flow control signals, galvanic isolated

IL-NT AOUT8 interface (optional card)

Plugs into IL-NT controller EXTENSION MODULE port.

Number of PWM outputs 8

PWM frequency 250Hz
Maximum current 0.5 A
Maximum switching voltage 36 VDC
Output resistance 1
Resolution 10 bits

IGS-PTM
Voltage supply 8-36V DC
Consumption 0,1A depend on supply voltage
Mechanical dimensions: 40 x 95 x 45 mm , DIN rail (35 mm) mounted
Interface to controller CAN
Binary inputs and outputs see IG-IOM
Analog output see IG-IOM

Analog inputs
Not electrically separated
Number of inputs 4
Resolution 10 bits
Maximal resistance range 0 250
Maximal voltage range 0 100 mV
Maximal current range 0 20 mA
Resistance measurement tolerance 1 % 2 out of measured value
Voltage measurement tolerance 1,5 % 1mV out of measured value
Current measurement tolerance 2,5 % 0,5mA out of measured value

IGL-RA15
Power supply
Voltage supply 8-36V DC
Consumption 0,35-0,1A (+1A max horn output)
Depend on supply voltage

Operating conditions
Operating temperature -20..+70oC
Storage temperature -40..+80oC
Protection front panel IP65

Dimensions and weight

Dimensions 180x120x55mm
Weight 950g

Horn output
Maximum current 1A
Maximum switching voltage 36 VDC

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 75

IL-NT-MRS-1.0.pdf
IG-IB
Voltage supply 8-36V DC
Consumption 0,1A depend on supply voltage
Mechanical dimensions: 95 x 96 x 43 mm , DIN rail (35 mm) mounted
Interface to controller RS232
Interface to modem RS232
Interface to Ethernet RJ45 (10baseT)
Operating temperature -30..+70oC
Storage temperature -30..+70oC

InteliLiteNT MRS10/11/15/16, SW version 1,0, ComAp August 2007 76

IL-NT-MRS-1.0.pdf