Scribd
Upload
3K views11 pages

How To Install Artcut - Asc365

1. Connect the plotter to the computer using a USB cable and run the SETUP.EXE file to install the USB driver. 2. If using Windows Vista or 7 and the driver does not install, update the driver software by browsing to the USBDriver folder. 3. After installing the USB driver, configure the serial port settings in Artcut and select XON/XOFF flow control at 9600 baud.

Uploaded by

Maria Jose Hernandez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3K views11 pages

How To Install Artcut - Asc365

1. Connect the plotter to the computer using a USB cable and run the SETUP.EXE file to install the USB driver. 2. If using Windows Vista or 7 and the driver does not install, update the driver software by browsing to the USBDriver folder. 3. After installing the USB driver, configure the serial port settings in Artcut and select XON/XOFF flow control at 9600 baud.

Uploaded by

Maria Jose Hernandez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

HOW TO INSTALL ARTCUT

www.asc365.com

When you connect the plotter and computer by USB cable, Please firstly install the USB driver as bellow:

1. Turn on cutter/plotter, connect computer and plotter by USB Cable. Double click "SETUP.EXE".

2. Click the "INSTALL


INSTALL
INSTALL"
OK
When finished installation, click "OK
OK".

If your computer system is VISTA or WIN7WIN7,, can not install the USB driver, please refer to the below:
My computer
1. Right click "My properties
computer" > "properties Device Manager "
properties" > "Device
Unknown device
you can find "Unknown device", double click it, pop up a window
Update Driver
then click "Update Driver"
2.
2.Click " Browse my computer for driver software
software"
3. Browse
3.Click "Browse
Browse"
C:/USBDriver/
Select "C:/USBDriver/
C:/USBDriver/" Note
Note: that is according to which folder the plotter driver stored in.
SETUP.EXE
4. After update the Driver, then Double click "SETUP.EXE
SETUP.EXE" to finish installing the USB driver.
5. USB driver installed ready, the port should show "USB-SERIAL CH341A(COM3)"
Port Setting
Click port, "Port Setting"
Flow control
Select "Flow Xon/Xoff
control" as "Xon/Xoff flow control
Xon/Xoff"; set "flow 9600
control" as "9600
9600".
set engraver/routers output
6. In the Artcut, On the "set device set up
output" screen in "device serial port setting
up" under "serial setting", please
XON/XOFF
select"XON/XOFF RTS/CTS
XON/XOFF" and "RTS/CTS
RTS/CTS".
If by COM cable, please set it according the below:
1. set engraver/routers output
1.On the "set device set up
output" screen in "device serial port setting
up" under "serial XON/XOFF
setting", please select"XON/XOFF
XON/XOFF" and
RTS/CTS
"RTS/CTS
RTS/CTS".
2.
2.In "device manager" under "communications port (com1) properties" in "port setting" tab, please set "flow control" as "9600".
Save the ARTCUT and USB driver on your DESKTOP, If you can not open the Artcut after installing, Please go to "Command Command Prompt"
Prompt", input
"C:\Artcut\wt.exe" /NCRC , then press "enter", appear a window of antivirus software, please select to allow operating.

You might also like