Scribd
Upload
101 views

Net Optics 10/100/1000baset Tap

The Net Optics 10/100/1000BaseT Tap allows for passive monitoring of 10/100/1000 copper network links at speeds of 10, 100, or 1000 Mbps. It features Link Fault Detect to notify monitoring devices of link failures and delivers full-duplex traffic monitoring with zero impact on network performance. The Tap establishes permanent access ports without acting as a single point of failure or disturbing other network connections.

Uploaded by

Achmad Arthur Pradhana R-
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
101 views

Net Optics 10/100/1000baset Tap

The Net Optics 10/100/1000BaseT Tap allows for passive monitoring of 10/100/1000 copper network links at speeds of 10, 100, or 1000 Mbps. It features Link Fault Detect to notify monitoring devices of link failures and delivers full-duplex traffic monitoring with zero impact on network performance. The Tap establishes permanent access ports without acting as a single point of failure or disturbing other network connections.

Uploaded by

Achmad Arthur Pradhana R-
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Net Optics 10/100/1000BaseT Tap

Get total traffic visibility for 10/100/1000 monitoring and security devices by placing Net Optics 10/100/1000BaseT
Taps on critical network links. 10/100/1000BaseT Taps support passive monitoring of 10/100/1000 links at 10, 100, or
1000 Mbps. This Tap is ideal when a passive Tap is required for use with a variety of copper monitoring devices.

For superior reliability, the 10/100/1000BaseT Tap features Link Fault Detect (LFD), which gives the devices
connected to the Tap critical information about link status. If either side of the bi-directional link fails, the Tap
immediately communicates the fault to both devices, reducing the time required to activate a redundant path.

Transparent Access

The 10/100/1000BaseT Taps establish permanent passive access ports without introducing a point of failure or
disturbing other network connections. The 10/100/1000BaseT Tap either auto-negotiates communication or uses an
external DIP switch to set fixed speed and duplexing parameters. These passive Taps deliver full-duplex monitoring
with zero impact on network traffic around the clock.

Security and Visibility

Without an IP address, monitoring devices are isolated from the network, dramatically reducing their exposure to
attacks. However, the monitoring device connected to the Tap still sees all full-duplex traffic as if it were in-line,
including Layer 1 and Layer 2 errors.

Simply Plug It In

Full-duplex monitoring is a snap when each side of the signal is sent to a separate NIC on the monitoring device. All
network and monitoring cables necessary for plug-and-play deployment are included with the Tap.

Reliability

For extra uptime protection, Net Optics 10/100/1000BaseT Taps offer redundant power connections. Should the
primary power source fail, the Tap automatically switches to the backup power source. Power LEDs on the front of
the Tap indicate the current power source.

Operating Specifications:
Operating Temperature: 0C to 55C
Storage Temperature: -10C to 70C
Relative Humidity: 10% min, 95% max, non-condensing

Mechanical Specifications:
Power Supply:
Input: 100-240VAC, 0.5A ~ 47-63Hz
Output: 12V 1.5A

DC Power Input: -48 VDC typical, -36 VDC min, -75 VDC max
Dimensions: 1.125 high x 6.25 deep x 4.5 wide

Cable Interface:
Copper Cable Type: 22-24 AWG unshielded twisted pair cable, CAT5E
Link Distance Supported: 100 meters

Connectors:
(2) RJ45, 8 pin connectors (monitor ports)
(2) RJ45, 8 pin connectors (network ports)

Certifications:
Fully RoHS compliant

Part Numbers:
TP-CU3
Passive, Secure Technology

Provides passive access at 10/100/1000 Mbps without data stream interference or introducing a point of failure
Permanent in-line installation without affecting network performance
Link Fault Detect prevents undetected link failures
Passes all full-duplex traffic (including errors) from all layers for comprehensive troubleshooting
No IP address is needed for the Tap or monitoring device, enhancing monitoring security
Compatible with Power over Ethernet (PoE) applications
Redundant power ensures monitoring uptime
Fully IEEE 802.3 compliant
Fully RoHS compliant

Warranty

All Net Optics products come standard with a 1 year manufacturer's warranty
Optional 1 or 2 year extended warranty available at time of product purchase

Ease of Use

LED indicators show redundant power and link status


DIP switches select auto-negotiation of fixed speed and duplexing settings for the Tap
Front-mounted connectors make installation and operation quick and easy
All network and monitoring cables included
Silk-screened application diagram illustrates all connections for easy deployment
Optional 19-inch rack frame holds up to 3 or 12 Taps
Tested and compatible with all major manufacturers monitoring devices, including protocol analyzers, probes, and
intrusion detection/prevention systems

Part Numbers

10/100/1000BaseT Tap
- TP-CU3 Tap, Copper, 10/100/1G
- TP-CU3-DC Tap, Copper, 10/100/1G (-48V)
- RK-3V2
3-Slot Rack Mount Frame

-RK-12V2
12-Slot Rack Mount Frame

You might also like