Scribd
Upload
163 views

OSPF in Point-To-Multipoint

1. OSPF point-to-multipoint treats Frame Relay links as point-to-point links, so no DR/BDR is elected. It uses unicast to transmit OSPF packets instead of multicast. 2. The default hello and dead intervals for point-to-multipoint links are 10 seconds and 40 seconds respectively. 3. In the lab, R1, R2 and R3 are configured with OSPF in area 0 over point-to-multipoint Frame Relay links using the specified DLCI mappings, allowing R2 to ping R3's interfaces despite the lack of a direct mapping between R2 and R3.

Uploaded by

kmad
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
163 views

OSPF in Point-To-Multipoint

1. OSPF point-to-multipoint treats Frame Relay links as point-to-point links, so no DR/BDR is elected. It uses unicast to transmit OSPF packets instead of multicast. 2. The default hello and dead intervals for point-to-multipoint links are 10 seconds and 40 seconds respectively. 3. In the lab, R1, R2 and R3 are configured with OSPF in area 0 over point-to-multipoint Frame Relay links using the specified DLCI mappings, allowing R2 to ping R3's interfaces despite the lack of a direct mapping between R2 and R3.

Uploaded by

kmad
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Lab 4 - OSPF in Point-to-Multipoint

Prerequisites: CCNP level skills.

Cisco IOS OSPF modes:

1. Point-to-point (Cisco)
2. Broadcast (Cisco)
3. Non-broadcast (RFC 2328)
4. Point-to-multipoint (RFC 2328)
5. Point-to-multipoint non-broadcast (Cisco)

Topology
Pic. 1 - Topology Diagram.

Icons designed by: Andrzej Szoblik - http://www.newo.pl

Workflow
1. Get familiar with the topology.
2. Read the 'Task List'.
3. Read the 'Questions' and provide the answers BEFORE configuring the routers.
4. Configure the lab according to the 'Task List' .
5. Compare the answers (step 3) with the lab results.

Task List
Configure IP addresses as per topology diagram and use encapsulation Frame-Relay on
S0/0 interfaces.
Make sure that you use only DLCIs specified in the topology diagram (pic. 1) and routers
do not learn any other DLCIs dynamically.
R2 should use only one layer 3 to layer 2 mapping. Also R3 should use only one layer 3
to layer 2 mapping.
Configure OSPF with all links in area 0. Make sure that R2 can ping R3's loopback0 and
S0/0 interfaces (R2 must not have frame-relay mapping to R3).

Questions
1. What are the differences betweent OSPF point-to-multipoint and non-broadcast on
Frame-Relay links?
2. Does point-to-multipoint mode networks use multicast or unicast to transmit OSPF
packets? Why?
3. What are the default hello/dead interval timers on point-to-multipoint links?

Lab Solution
R1 Configuration:
!
interface loopback0
ip address 172.16.101.1 255.255.255.0
ip ospf network point-to-point
!
interface Serial0/0
ip address 10.1.1.1 255.255.255.0
encapsulation frame-relay
ip ospf network point-to-multipoint
frame-relay map ip 10.1.1.2 102 broadcast
frame-relay map ip 10.1.1.3 103 broadcast
no frame-relay inverse-arp
!
router ospf 1
router-id 1.1.1.1
log-adjacency-changes
network 10.1.1.1 0.0.0.0 area 0
network 172.16.101.1 0.0.0.0 area 0
!

R2 Configuration:
!
interface Loopback0
ip address 172.16.102.2 255.255.255.0
ip ospf network point-to-point
!
interface Serial0/0
ip address 10.1.1.2 255.255.255.0
encapsulation frame-relay
ip ospf network point-to-multipoint
frame-relay map ip 10.1.1.1 201 broadcast
no frame-relay inverse-arp
!
router ospf 1
router-id 2.2.2.2
log-adjacency-changes
network 10.1.1.2 0.0.0.0 area 0
network 172.16.102.2 0.0.0.0 area 0
!

R3 Configuration:
!
interface Loopback0
ip address 172.16.103.3 255.255.255.0
ip ospf network point-to-point
!
interface Serial0/0
ip address 10.1.1.3 255.255.255.0
encapsulation frame-relay
ip ospf network point-to-multipoint
frame-relay map ip 10.1.1.1 301 broadcast
no frame-relay inverse-arp
!
router ospf 1
router-id 3.3.3.3
log-adjacency-changes
network 10.1.1.3 0.0.0.0 area 0
network 172.16.103.3 0.0.0.0 area 0
!

Verification
Note!
OSPF point-to-multipoint treats the circuits as point-to-point links so no DR/BDR are elected. In
addition to that, the spokes do not have to have IP-to-DLCI mapping via R1. R1 resolves the
reachability between spokes by injecting itself as the next-hop. Both spokes know how to reach
R1 according to IP-to-DLCI static mapping.

Pic. 2 - Only DLCIs as per Topology Diagram.

Pic. 3 - R1's Adjacencies with R2 and R3.

Pic. 4 - R2 /32 Route Injected by R1.

Pic. 5 - Traceroute.

You might also like