Scribd
Upload
218 views2 pages

Ma Tds Dtnet ZN Rev19

This technical data sheet provides specifications for zinc coated rockfall protection netting. The netting is made of double twisted galvanized steel wire mesh certified to ISO 9001 standards. It is used as a draping system to prevent rocks and debris from falling. Table 1 lists the standard sizes for the netting with lengths from 25-100 meters and widths from 2-4 meters. Table 2 provides the nominal tensile strength of the mesh in accordance with EN 10223-3. The netting has an average punching load capacity tested according to UNI 11437.

Uploaded by

sundra0
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
218 views2 pages

Ma Tds Dtnet ZN Rev19

This technical data sheet provides specifications for zinc coated rockfall protection netting. The netting is made of double twisted galvanized steel wire mesh certified to ISO 9001 standards. It is used as a draping system to prevent rocks and debris from falling. Table 1 lists the standard sizes for the netting with lengths from 25-100 meters and widths from 2-4 meters. Table 2 provides the nominal tensile strength of the mesh in accordance with EN 10223-3. The netting has an average punching load capacity tested according to UNI 11437.

Uploaded by

sundra0
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

TECHNICAL DATA SHEET

Rev. 19, Date 15.12.2014

ROCKFALL PROTECTION NETTING


ZINC COATED

The mesh consists of double twisted galvanised (Zn) coated


steel woven wire. The mesh is produced in accordance with
standard EN10223-3.The management and production system
is certified in compliance with standards ISO 9001.

Steel woven wire mesh is used as a drapery system to prevent


rocks and debris from falling onto roads and railways.
Dimensions of the Zinc coated net are stated in Table 1.
The nominal tensile strength of the mesh shall be as per Table
2; tests carried out in compliance with EN 10223-3:2013.
The average punching load capacity of the netting is in
compliance with the tests carried out in accordance with UNI
W
11437.
Width
Wire
The steel wire used in the production of the mesh is coated
with Zn class A.
All tests on wire must be performed prior to manufacturing the
mesh. Figure 1
1. Tensile strength: the wire used for the manufacture of
Zinc coated mesh shall have a tensile strength between
350-550 N/mm2 as per EN10223-3:2013. Wire tolerances
(Table 3) are in accordance with EN10218 (Class T1).
2. Elongation: Elongation shall not be less than 8%, as per
EN10223-3:2013.
3. Zinc coating: minimum quantities of Zinc (Table 3) meet the The tolerance on the mesh size
M being the distance between the M
requirements of EN10244-2 (Table 1 - Class A).
axis of two consecutive twists, is
4. Adhesion of Zinc: the adhesion of the Zinc coating to the according to EN 10223-3: 2013
wire must be in accordance with EN 10244.

Figure 2

Example of Rockfall protection netting


Maccaferri reserves the right to amend product specifications without notice and specifiers are requested to
check as to the validity of the specifications they are using.

Table 1 - Sizes for rockfall protection netting 2. Standard mesh - wire combination
L=Length (m) W=Width (m) Nominal Mesh
Wire Average
M Tolerance Tensile
25 2, 3, 4 Type diameter punching
(mm) (mm) Strength
(mm) load kN
50 2, 3, 4 (kN/m)
100 2, 3, 4 6x8 60 -0/+8 2.7 55 82
All sizes and dimensions are nominal.
Tolerances of 0/+1 m of the length, and M of the height shall be 2.7 50 67
8x10 80 -0/+10
permitted 3.0 60 82

3. Standard wire diameter


Lacing Operations
Lacing operations can be made by using the tools shown Mesh wire
Selvedge Lacing
in Fig.5. Zinc coated steel rings having the following wire wire
specification can be used instead of lacing wire (Figs. 3,
4): 2.70 3.40
Internal diameter mm 2.2
3.00 3.90
diameter: 3.00 mm
tensile strength: >1720 MPa Wire tolerance () mm 0.06 0.07 0.06
Pullapart strength > 2.0 kN 245 (2.70) 265 (3.40)
Spacing of the rings must not exceed 200 mm (Fig.3) Min. quantity of coating gr/m2 230
255 (3.00) 275 (3.90)

Quantity Request
When requesting a quote, please specify:
size of rolls (length x height, see Fig.1),
type of mesh,
type of coating
EXAMPLE: No.100 rolls Length=25m, Width=4m - Mesh
type 8x10 - Wire diam. 2.70 mm - Zinc coated

1. Pliers

A 2. Pliers with nipper


3. Nipper

1 2 3

Figure 3: Lacing wire and Rings

B Pneumatic Spenax tool

Open Closed
19 mm

44 mm
Nominal overlap of
25 mm after closure
C Manual tool

Figure 4 Figure 5
MACCAFERRI ASIA
Bureau Veritas Certified Quality System Company with
Unit 3A-11, Block G, Phileo Damansara 1, 9,Jalan 16/11, Off Jalan Damansara, UKAS' s accreditation
46350 Petaling Jaya, Selangor, Malaysia Tel. (+603) 7957 8330 - Fax (+603) 7957 9080
E-mail: [email protected] Website: www.maccaferri.com

You might also like