Scribd
Upload
105 views

Computer Assembly: Connect All Internal Cables

The document provides instructions for connecting internal cables and components like power cables, data cables, and fans during computer assembly. It also covers reattaching side panels and connecting external cables and components like monitors, keyboards, mice and power once assembly is complete.

Uploaded by

ellen_rama
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
105 views

Computer Assembly: Connect All Internal Cables

The document provides instructions for connecting internal cables and components like power cables, data cables, and fans during computer assembly. It also covers reattaching side panels and connecting external cables and components like monitors, keyboards, mice and power once assembly is complete.

Uploaded by

ellen_rama
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

COMPUTER ASSEMBLY

Connect all internal cables


Connect the power cables

Power cables are used to distribute electricity from the power supply to the motherboard and other
components. Data cables transmit data between the motherboard and storage devices, such as hard
drives. Additional cables connect the buttons and link lights on the front of the computer case to the
motherboard.

Motherboard Power Connections

The Advanced Technology Extended (ATX) main power connector will have either 20 or 24 pins. The
power supply may also have a 4-pin or 6-pin Auxiliary (AUX) power connector that connects to the
motherboard. A 20-pin connector will work in a motherboard with a 24-pin socket.

Follow these steps for motherboard power cable installation:

1. Align the 20-pin ATX power connector to the socket on the motherboard.
2. Gently press down on the connector until the clip clicks into place.
3. Align the 4-pin AUX power connector to the socket on the motherboard.
4. Gently press down on the connector until the clip clicks into place.

SATA Power Connectors


SATA power connectors use a 15-pin connector. SATA power connectors are used to connect to hard
disk drives, optical drives, or any devices that have a SATA power socket.

Molex Power Connectors


Hard disk drives and optical drives that do not have SATA power sockets use a Molex power connector.

Berg Power Connectors


The 4-pin Berg power connector supplies power to a floppy drive.

Follow these steps for power connector installation:

1. Plug the SATA power connector into the HDD.


2. Plug the Molex power connector into the optical drive.
3. Plug the 4-pin Berg power connector into the FDD.
4. Connect the 3-pin fan power connector into the appropriate fan header on the motherboard,
according to the motherboard manual.
5. Plug the additional cables from the case into the appropriate connectors according to the
motherboard manual.
Connect the data cables

Drives connect to the motherboard using data cables. The drive being connected determines
the type of data cable used. The types of data cables are PATA, SATA, and floppy disk.

PATA Data Cables


The PATA cable is sometimes called a ribbon cable because it is wide and flat. The PATA
cable can have either 40 or 80 conductors. A PATA cable usually has three 40-pin connectors.
One connector at the end of the cable connects to the motherboard. The other two connectors
connect to drives. If multiple hard drives are installed, the master drive will connect to the end
connector. The slave drive will connect to the middle connector.

SATA Data Cables


The SATA data cable has a 7-pin connector. One end of the cable is connected to the
motherboard. The other end is connected to any drive that has a SATA data connector.

Floppy Data Cables


The floppy drive data cable has a 34-pin connector. Like the PATA data cable, the floppy drive
data cable has a stripe to denote the location of pin 1. A floppy drive cable usually has three
34-pin connectors. One connector at the end of the cable connects to the motherboard. The
other two connectors connect to drives. If multiple floppy drives are installed, the A: drive will
connect to the end connector. The B: drive will connect to the middle connector.

Plug the floppy drive data cable into the drive with the pin 1 indicator on the cable aligned to the
pin 1 indicator on the drive connector. Motherboards have one floppy drive controller, which
provides support for a maximum of two floppy drives.

Follow these steps for data cable installation:

1. Plug the motherboard end of the PATA cable into the motherboard socket.
2. Plug the connector at the far end of the PATA cable into the optical drive.
3. Plug one end of the SATA cable into the motherboard socket.
4. Plug the other end of the SATA cable into the HDD.
5. Plug the motherboard end of the FDD cable into the motherboard socket.
6. Plug the connector at the far end of the FDD cable into the floppy drive.

Re-attach the side panels and connect external cables to the computer

Now that all the internal components have been installed and connected to the
motherboard and power supply, the side panels are re-attached to the computer case.
The next step is to connect the cables for all computer peripherials and the power
cable.
Re-attach the side panels to the case

Most computer cases have two panels, one on each side. Some computer cases
have one three-sided cover that slides down over the case frame.

Once the cover is in place, make sure that it is secured at all screw locations. Some
computer cases use screws that are inserted with a screwdriver. Other cases have
knob-type screws that can be tightened by hand.

If you are unsure about how to remove or replace the computer case, refer to the
documentation or website of the manufacturer for more information.

Connect external cables to the computer

After the case panels have been re-attached, connect the cables to the back of the computer.
Here are some common external cable connections:

Monitor
Keyboard
Mouse
USB
Ethernet
Power

When attaching cables, ensure that they are connected to the correct locations on the
computer. For example, some mouse and keyboard cables use the same type of PS/2
connector.

Follow these steps for external cable installation:

1. Attach the monitor cable to the video port.


2. Secure the cable by tightening the screws on the connector.
3. Plug the keyboard cable into the PS/2 keyboard port.
4. Plug the mouse cable into the PS/2 mouse port.
5. Plug the USB cable into a USB port.
6. Plug the network cable into the network port.
7. Connect the wireless antenna to the antenna connector.
8. Plug the power cable into the power supply.

You might also like