Scribd
Upload
118 views7 pages

Dss Gerador de Audio PDF

This document provides instructions for a digital signal generator that uses an AVR microcontroller and DDS (direct digital synthesis) technique to generate various waveforms. It has two outputs - one for high speed square waves up to 8MHz, and another for adjustable DDS signals ranging from 1Hz to 65535Hz. The generator is controlled through a LCD menu using five buttons and allows selection of signal type, frequency setting in various steps, and adjustment of amplitude and offset via potentiometers. The circuit diagram shows it uses standard components like an AVR, LCD, resistors, op amps and can run off multiple voltage rails for flexibility.

Uploaded by

Adir Figueiredo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
118 views7 pages

Dss Gerador de Audio PDF

This document provides instructions for a digital signal generator that uses an AVR microcontroller and DDS (direct digital synthesis) technique to generate various waveforms. It has two outputs - one for high speed square waves up to 8MHz, and another for adjustable DDS signals ranging from 1Hz to 65535Hz. The generator is controlled through a LCD menu using five buttons and allows selection of signal type, frequency setting in various steps, and adjustment of amplitude and offset via potentiometers. The circuit diagram shows it uses standard components like an AVR, LCD, resistors, op amps and can run off multiple voltage rails for flexibility.

Uploaded by

Adir Figueiredo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

DDS Signal generator

user guide
NOTES: Please confirm the integrated circuit mounted in

correct direction!

After all the installation, connect the power supplyright

adjust the resistance 10K and you will see the character.

Adjust the character to clear type.

This signal generator has two outputs - one for DDS

signal and another for high speed [1,2,4,8MHz] square signal

- which may be used for reliving microcontrollers with wrong

fuse settings or for other purposes as well. High speed (HS)


signal is direct output from Atmega16 OC1A(PD5) pin. DDS

output is used for all other signals that are generated via R2R

resistor network and is adjusted via LM358N offset and

amplitude regulating circuits. Offset and amplitude can be

regulated by two potentiometers. Offset can be regulated in

range +5V..-5V while amplitude in range 0..10V. DDS

frequency range is from 1 to 65535Hz that is more than

enough for testing audio circuits and other tasks.

Main AVR DDS signal generator features:

Simple circuit with easily accessible and cheap

components;

Dedicated high speed (HS) signal output up to 8MHz;

DDS signal with variable amplitude and offset;

DDS signals: sine, square, saw, rev saw, triangle, ECG

and noise.

216 LCD menu;

Intuitive 5 button keypad.

Frequency adjusting steps: 1, 10, 100, 1000, 10000Hz;

Restoring last configuration after power up.


In the block diagram you may see logical structure of signal

generator:

As you can see device requires several voltages: +5V, -12V,

+12V, GND. -12V and +12V are used for offset and amplitude

control. In this case power supply is constructed by using

simple transformer and few voltagere gulators,

et:7812,7912,7805.
LCD menu control

All actions can be viewed in LCD menu. Menu can be

controlled with 5 buttons that are next to LCD module.

Up and down arrow buttons are used for browsing menu

while right and left arrow buttons are used for changing

frequency value. When middle button is pressed - signal

generating starts. Press middle button again to stop signal

generator.

Important to notice, that there is a separate menu for

changing frequency step. This is convenient if you need to

change generator frequencies in wide range. This allows to

set any frequency with relatively few button clicks.


Noise generation dont have frequency setting. It uses simple

rand function where results are continuously output to DDS

output.

High speed signal has four frequencies available: 1, 2, 4 and

8MHz.

Circuit diagram of DDS generator is very simple with easy

accessible components. It uses following parts:

AVR Atmega16 microcontroller clocked with 16MHz

external crystal;

Standard HD44780-based 216 LCD module;

R2R DAC made of simple resistors(1% tol);

LM358N low power dual op amplifier;

Two potentiometers;

5 buttons;

several connectors and sockets.

We offer a programmed IC and all components in the suite.

You might also like