Control Panel Technical Guide PDF
Control Panel Technical Guide PDF
Technical Guide
How to reduce damage to components
through effective thermal management
To find
out more
about thermal management
solutions for control enclosures,
please consult our catalogue
or visit our website at
www.schneider-electric.com
2
Contents
Introduction 4 to 7
1 Analysis of thermal
conditions
Internal analyses
8 to 13
External analyses
2
Thermal optimisation
solutions
Overview 14 to 15
"Passive" solutions 16 to 26
"Active" solutions 27 to 55
3 Practical summary 58 to 61
4
Guide for choosing thermal
optimisation solutions 62 to 69
3
All the expertise of Schneid
to the therm
of your enclo
4
er Electric devoted
al management
sures
Reasons
why installations
shut down
or malfunction Consequences
In the vast majority of cases, when electric Even the slightest shut-down or malfunction
installations and devices housed in control of the electrical installation can have
enclosures shut down or malfunction, major even catastrophic financial
the problem is thermal: excessively high repercussions for a company, regardless
or low temperature of electrical and, of its business sector.
especially, electronic equipment.
Here are some examples of business
sectors in which 1 hour of down time
can be very expensive:
Uncontrolled external
climatic conditions 40,000 Glassworks
90,000 Airline
ticket-booking
services
Avoiding Reducing
down-time and costs associated
malfunctions with the manufacturing
caused by processes
overheating
maintenance
of electrical and
cycles and costs
electronic devices
for the installation
Extending Guaranteeing
the service life
continuity of service
of the internal
components
6
The ideal combination
for an installation,
with no breakdown risk
Knowledge
of losses of power
in the installation (in W)
Installation with no
breakdown risk and
suitable protection
7
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Analysis
of thermal
conditions
8
1
Analysis of thermal conditions
It is essential to calculate a complete, reliable heat balance
before considering any management solutions.
A heat balance consists of measuring and analysing thermal
conditions inside AND outside the enclosure.
Based on these measurements, the ProClima v5.0 software will help
you identify the solutions that best suit your control enclosure
and the environment in which it is installed.
Zoom on
Your heat balance with ProClima v5.0
software
How does it work? Nothing could be easier!
9
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Important to know
Critical temperature for each device
Critical humidity level for each device
Expert's tip
The thermal management solution must be sized The mean working temperature recommended
according to the critical temperature of the most for the inside of the enclosure is 35C.
delicate element of the enclosure. This temperature This is the reference temperature for the control
should never be exceeded. equipment integrated in the thermal solution.
10
Analysis of thermal conditions
losure
Expert's tip
The temperature measurement inside the enclosure should be taken in three
separate areas (T1, T2 and T3). Avoid the ventilated hot-air outlet.
The hot-air ventilation flows affect the temperature in the various areas.
Also, each case must be studied separately and in detail.
Mean temp. of the enclosure = (T1 + T2 + T3) / 3.
Expert's tip
Use the ProClima v5.0 software to find out the dissipation value of the components
in your enclosure. ProClima v5.0 offers the loss values for all the most common
devices on the market.
11
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
What to measure
> Max. mean temperature
> Min. mean temperature
12
Analysis of thermal conditions
Plant manufacturing car parts. The presence Fan not working due Busbar installed in a water treatment site.
of oil in the environment reduces the service life to the presence The humid, corrosive atmosphere has damaged
of the components. of sugar in the plant the copper.
(beer production).
Find out whether the temperature and the quality of the external air can help cool
the enclosure ("Passive" solution).
Knowing the installation site well helps optimise the protection level of the thermal
solution (e.g.: filter thickness) and the protection level of the enclosure
(e.g.: IP degree according to EN 60529).
13
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Thermal
optimisation
solutions
14
2
Thermal optimisation solutions
There are two main families of thermal management solutions:
so-called "Passive" solutions (inexpensive and natural,
defined upstream from the installation, etc.) and so-called
"Active" solutions (corrective solutions, requiring specific sizing,
possibly expensive, etc.).
"Passive" "Active"
solutions solutions
Choice of material Thermal control device
Expert's tip
Maximise the use of "Passive" solutions before choosing
an "Active" solution.
15
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
"Passive" solutions
Choice of material
1 The choice of material for the enclosure (steel, polyester) is essential
for ensuring the natural dissipation of calories released by
the electrical or electronic devices.
Zoom on
Mean the phenomenon of natural dissipation of calories
values
Natural dissipation of calories depends on the total heat-transmission coefficient: K.
of K Total heat transmission = All processes that contribute to heat transmission:
For iron: Q = K x S x (Te Ti)
5,0 to 5,5 Where,
K = Heat flow when stationary, divided by the surface area and the temperature
For aluminium: difference between the equipment on either side of the system.
12,0 It is measured in W/m2 x K.
The three forms of heat transfer are included: conduction, convection
For polyester: and transmission.
3,5
Expert's tip
When the external temperature is favourable (< 35C), increasing the size
of the enclosure makes it possible to reduce the internal operating temperature
and slow down a possible temperature rise.
16
Thermal optimisation solutions "Passive" solutions
17
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Expert's tip
In the latter case, extraction must be carried out in an "Active" manner, using
an air-conditioner or an air-water exchanger.
The energy saving (measured by the cooling capacity gain) is around 25% for metal
enclosures and 12% for polyester enclosures.
2
2
1 1 3
1 2 3
Irradiated heat source Air-conditioner Insulation
(furnace for glass,
ceramic, molten metal,
etc.)
Expert's tip
Insulation can also be used as a "Passive" solution when the external
temperature is very low and permanently exceeds the critical temperature
of the installed devices.
E.g.: installations in cold storage rooms, outdoors (20C), etc.
18
Thermal optimisation solutions "Passive" solutions
Expert's tip
A thermal partition can be used to separate loads and optimise the solution
and its overall cost.
It is preferable to separate the control enclosures and the power enclosures.
1 3 0W 3 0W
Power enclosures 250 50
0W
2 20
Control enclosure 0W
50
0W 250
3 Cooling unit
W W
00 00
4 30 ing 30
ool
Ventilation
c
for
ed
uir
req
rgy
Ene
52%
Increased energy efficiency
Expert's tip
The highest loads must be installed as low down as possible. In this way, the amount
of air inside the enclosure can cool the dissipated heat and favour internal air convection.
19
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Rules to be observed
concerning the layout of devices inside the enclosure
Respect the air gap distances inside the enclosure.
Create an air column covering the entire height of the enclosure (100 to 200 mm wide), between
the air intake and outlet. This will avoid overheating and losses of thermal efficiency.
3 3 1
1
3
3
2 2
100
200
mm
20
Thermal optimisation solutions "Passive" solutions
17%
Increased energy
for example, with the braking resistances of the variable speed
drives (around 500 W to 3.5 kW).
These calories must be extracted using cooling units
efficiency ("Active" solutions), unless this type of equipment is installed
outside of the enclosure.
Direct energy
efficiency
Optimisation
of the "Active"
Expert's tip
Moving passive electric loads outside of the control enclosures reduces the power
thermal solution
of thermal solutions and its consumption.
Cable layout
7 The wiring of the devices can be a source of heating.
Also, there should be good habits:
The cables should not rest on the devices
The ventilation grilles should not be obstructed
Screw/snap-fit the locking elements
21
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Air-flow management
8 Free space above and below for ventilation
1 1
100 mm
Ventilation
2 of at least 100 mm 2
above and below 2
Equipment (drives or
electronic equipment)
100 mm
1 1
1 cable duct
Expert's tip
Avoid blocking the air outlets of the electronic equipment.
Always leave a ventilation space of at least 100 mm at the top and bottom
(= extended service life for the devices).
22
Thermal optimisation solutions "Passive" solutions
Expert's tip
Use the ProClima v5.0 software to calculate the natural dissipation
capacity of your enclosures.
It is advisable to be able to direct the flow from the air circulating fans
(e.g.: towards delicate devices, recurring hot spots, etc.).
The greater the mixing flow, the quicker dissipation will take place.
23
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
50
C 40
Ti Ti C
24
Thermal optimisation solutions "Passive" solutions
1 1
Air-conditioner
Expert's tip
Leave an additional air-circulation space of at least 150-200 mm deep.
25
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
26
Thermal optimisation solutions "Active" solutions
"Active" solutions
27
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
28
Thermal optimisation solutions "Active" solutions
Example 1: Example 2:
At the top (the hottest part Next to the most delicate devices
of the enclosure)
S1
S2
Up to
58%
Energy savings
(compared with
a solution without
thermal control)
Two fans + one thermostat equipped with One fan + one resistor + one thermostat
two relays provide two flow levels equipped with two probes (S1, S2) make it
according to the inner temperature: possible to control two local temperature
levels:
Fan 1 active if Ti = 45C
Fan active if temperature of S1 Ti = 45C
Fan 2 providing support if Ti = 55C
Resistor active if temperature of S1 Ti = 10C
Probe S2 located outside (outdoor
applications).
Expert's tip
Two additional probes can be used to optimise the measurement.
29
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Expert's tip
Electronic thermostats and hygrostats are more accurate than mechanical models.
A TH, HY or HYT controller can be used to reduce the consumption of the thermal
solution.
Install the thermostats in the top of the enclosure: this is the hottest part.
As for the hygrostats, the best location is the bottom of the enclosure:
this is the most humid part.
30
Thermal optimisation solutions "Active" solutions
Forced convection
2 (through the appliance) with grilles
Exemple :
1
Min. 100 mm
1
Drive
Expert's tip
Select the filter type according to the environment in which the enclosure is installed
(difficult, harsh, polluted, etc. or good air quality).
Service the filter on a regular basis to avoid clogging and loss of flow.
31
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Outlet grille
Delivered with G2 M1 synthetic standard filter.
Material: injected thermoplastic (ASA PC),
self-extinguishing according to UL94 V0.
32
Thermal optimisation solutions "Active" solutions
Forced ventilation
3
When combined with a thermal control device, forced ventilation
is one of the best solutions in terms of energy efficiency.
Expert's tip
The external environment must be favourable: amount of dust,
temperature level and humidity level.
The delta T (Ti Te) should always be 5C.
Measure the external temperature before validating the solution.
The thermal controller is very useful for adapting the power of the "Active"
solution to the required charge level. For example, you can use two fans
and only activate one or two according to the temperature.
If the enclosure is properly sized and the loads are properly distributed:
> Ventilation direction pointing inwards
> If the enclosure heats up too much (Temp. > 60C), use a centrifugal fan
(ventilation with roof extraction).
X2
Service life
of the fans
33
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Ti
2 The air intake is particularly sensitive to loss
of flow
1
To avoid dust and air intakes: leave
Te a distance of 100 mm from the floor
150 mm
Side-mounted ventilation
solutions by Schneider Electric
The ClimaSys forced ventilation range fulfils most cooling needs,
with energy savings and high performance levels.
34
Thermal optimisation solutions "Active" solutions
Example 1: Example 2:
At the top (the hottest part Next to the most delicate devices
of the enclosure)
S1
S2
Two fans + one thermostat equipped One fan + one resistor + one thermostat
with two relays provide two flow levels equipped with two probes (S1, S2) make it
according to the inner temperature: possible to control two local temperature
levels:
Fan 1 active if Ti = 45C
Fan active if temperature of S1 Ti = 45C
Fan 2 providing support if Ti = 55C
Resistor active if temperature of S1 Ti = 10C
Probe S2 located outside (outdoor
applications).
35
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Ti
The air inlet is particularly sensitive
to loss of flow
150
mm
Expert's tip
If the enclosure heats up too much (Temp. 60C),
use the top-mounted extraction ventilation, with high-speed
centrifugal fan (from 500 m3/h)
It is essential to use filter-clogging and thermal control elements.
36
Thermal optimisation solutions "Active" solutions
P (PA)
1 3
2 Centrifuge
Flow in m3/h
Actual flow Free flow
(actual air entering
the cabinet)
Top-mounted ventilation
solutions by Schneider Electric
The ClimaSys top-mounted ventilation range is a natural airing device for coupling
to the top of metal floor-standing enclosures. Ideal solution for combining
with the ventilation slots.
37
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Temperature management
4 with air-conditioners
Air-conditioners or cooling units are widely used for cooling enclosures which contain
devices that give off a lot of heat.
They dehumidify the total volume of the enclosure by extracting condensation water.
Expert's tip
Use deflectors to avoid heat shocks.
If the hot-air emitted by the air-conditioner is in direct contact with the air outlet
of the drives, a heat shock may occur (condensation forming in the enclosure).
Make sure the drives are correctly centred relative to the thermal solution.
Have the filters replaced regularly by the maintenance team (e.g.: every four weeks
for critical workshops).
Avoid the typical mistake of blocking the air-conditioner air outlet. Consequences
of the blockage: reduced performance and/or appearance of heat shocks.
38
Thermal optimisation solutions "Active" solutions
Drive-cooling architecture
with side-mounted air-conditioner
1 2 1
Drive
2
100
mm 100 mm deflector width Cooling unit
Mounting plate
Entrance hot-air
Speed drive
or PLC's
Cooling Unit
80
Exit cooled air mm
39
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
1600
Ti[ C ]
1400
Cooling capacity 50
45
required under real 1200
Pf [ W ]
40
conditions to extract 35
1000 This area is very important,
the calories from 30
800 25 it tells us how much the compressor
the loss of power
20 can withstand (55C)!
of the drives.
600
Only performing cooling units withstand
400 such high temperatures!
20 25 30 35 40 45 50 55
Te[ C ] f=50 Hz
Expert's tip
Save time by using the ProClima v5.0 software and selecting
the cooling unit that is best suited to the demands of your installation.
40
Thermal optimisation solutions "Active" solutions
Drive
Expert's tip
Leave enough space to guarantee correct convection, from the roof
to the bottom of the enclosure.
Leave a minimum lateral depth of 150 mm, and avoid any obstacles
(risk of loss of load and performance).
41
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
B A
3
The cold air outputs from inside the enclosure should be free
of obstacles.
> 200 mm
> 300 mm > 300 mm
Possible
Pay special attention to minimum condensation problems.
clearances.
42
Thermal optimisation solutions "Active" solutions
der Electric
4 Technical rooms.
mm
00
>3
mm >1
00 00
>3 mm
5
In small spaces
the renovation
of the ambient air
is indispensable.
Otherwise, ambient
temperatures 55C
could easily be
reached and the group
would shut down.
6
The lack of sealing in the enclosure reduces performance and increases
water condensation in the evaporator.
Typical problem of the badly-closed door, badly sealed cables glands,
high roofs, etc.
Expert's tip
Save time by using the ProClima v5.0 software and selecting
the cooling unit best suited to the demands of your installation.
43
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Useful information!
> Check that the cable entries are perfectly sealed
The most common mistake with the enclosure + air-
conditioner solution is leaving the cable-entry open,
and not providing a sealing system (foam, etc.).
Area to be
protected
44
Thermal optimisation solutions "Active" solutions
Expert's tip
If the environment is pollutant-free, you can do without the filter.
In this case, the cooling unit will gain performance (around 5% to 10% higher).
45
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
G
F
B
E C
D
A
Expert's tip
Before installing an active water-evacuation solution:
Check the amount of water generated by the air conditioning.
NB.: for a dry environment, this should be low or even very low.
Check whether it is possible to use an external water outlet.
Check for proper water circulation: downwards (no curves on the initial level)
Use a transparent pipe in order easily to identify any clogging or plugs in the pipe.
46
Thermal optimisation solutions "Active" solutions
High efficiency
Withstands extreme temperature conditions (up to 55 C)
Guaranteed protection rating: IP 54 and IP 55 (range SLIM)
Built-in adjustable thermostat
Automatic evaporation system (roof-mounting installation)
Maximum security
Easy maintenance (access to the condensers)
Environmentally friendly: R134a (HFC) eco-friendly gas
47
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Temperature management
5 with air-water exchangers
Air-water exchangers are used mainly for cooling or heating
enclosures installed in difficult or harsh environments:
cemeteries, paint production chains, oily workshops, etc.
Places where filters clog very quickly.
This solution is completely sealed (up to IP 54).
The air-water exchanger is capable of extracting a large
number of calories from the enclosure (by fluid exchange).
These calories are then released outside the plant
(chiller-type cooling unit).
This means that the water can come from other sources.
Constraints: High evacuation of calories + high seal Constraints: Level of dust (filters blocking)
+ humidity/condensation
Expert's tip
Save time by using the ProClima v5.0 software, selecting the air-water exchanger
that is best suited to the demands of your installation.
48
Thermal optimisation solutions "Active" solutions
> Composants
Fan condenser
Thermostat
Terminal box
Fan
Pressure switch
Exchange cassette
Anti-return valve
Electro-valve reel
Electro-valve
Expert's tip
Please consult our catalogues to find performance curves according
to the water flow rate, water temperature and the desired working temperature
inside the enclosure.
49
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
50
Thermal optimisation solutions "Active" solutions
Temperature management
6 with air-air exchangers
Expert's tip
Save time by using the ProClima v5.0 software, selecting
the air-air exchanger that is best suited to the demands
of your installation.
Perform regular preventive maintenance of the battery
of the exchanger.
51
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Ti
Te
Ti>Te
Parts
Exchange cassette
Two Fans. For the inside circuit (permanent operation)
and for the outside circuit (driven by the thermostat)
They are of the centrifugal type, with good behaviour
in case of pressure losses
Thermostat installed as standard.
It controls the operation of the outside fan
52
Thermal optimisation solutions "Active" solutions
53
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Resistance heaters
7 External temperature changes (outdoor installations) or extreme
temperature levels (< 5C), can create a phenomenon of
condensation (on electronic devices located inside the enclosure)
or even cause malfunctions during the starting cycle.
C
i = 35
T 4%
=1
C Hr
i = 20
T 3%
=3
C Hr
10
Ti = 3%
Hr
=6 Expert's tip
5C Check that the resistance heater
Ti = 0%
=9 is correctly installed using a hygrostat
Hr ions
ndi
t (checking the relative humidity:
Co part
de
d RH as a %) or a thermostat
(checking the temperature in C or F)
The enclosure must be sealed
to prevent humid air from entering
the hot areas of the enclosure.
54
Thermal optimisation solutions "Active" solutions
Aluminium resistors
Equipped with a PTC-type detector
Eight power levels from 10 W
to 400 W
Improved convection
Quick fixing
(clipping on 35-mm DIN rail)
Connection terminal board
(heaters > 20 W)
55
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
P r o C l i m a v 5.0 s o f t w a r e : T h e
Your thermal study in seven steps
56
Thermal optimisation solutions ProClima v5.0 software
e s s e nt i a l ex p e r t ' s t o o l
57
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Practical
summary
58
3
Good reflexes for thermal
management of enclosures
Expert's tip
Plan thermal management (before installing the enclosure).
59
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
"Passive" Solutions
Steel: 26%
52%
Energy savings
Energy savings
38C
Temp. savings
Moving loads
to the outside
52%
Energy savings
Polyester:
64%
Energy savings Load distribution
60C
Temp. savings
52%
Energy savings
25C
Temp. savings
60
Thermal optimisation solutions Practical summary
ement of enclosures
"Active" Solutions
12%
Energy savings
58%
Energy savings
20C
Temp. savings
61
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Choosing
the best thermal
management solution
62
4
Selection guide
63
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Natural convection causes the temperature Air-air exchangers are equipped with
to drop inside the enclosure. Simple Fans with filters are designed to evacuate an aluminium exchange cassette which
solutions for this case include installing a large amount of heat economically. separates the internal and external air
grilles (without filter) or lifting the top. circuits and prevents the entry of dust.
NO NO YES
conomic solution.
E
T
he internal and external air circuits are
E
conomic solution. asy maintenance.
E
independent.
Advantages N
o maintenance. uick and easy installation.
Q
E
asy maintenance.
Q
uick and easy installation. ven temperature inside the enclosure.
E
H
igh protection rating: IP 54.
igh protection rating: IP 54 or IP 55.
H
T
he temperature inside the enclosure is
always higher than the external tempera-
S
mall amount of heat evacuated. ture. T
he temperature inside the enclosure is
Disadvantages R
eduction of the IP protection rating. T
he internal and external air circuits are in always higher than the external tempera-
E
ntry of dust particles. contact. ture.
M
aintenance required: filter
replacement.
Solutions
64
Thermal optimisation solutions Selection guide
The air-water exchangers are used to evacuate large The cooling units can be used in the harshest
amounts of heat. They require a cold-water circuit environments, where the temperature can reach
The resistance heaters are used to reheat the
with stable temperature and flow rate. up to 55 C.
electrical switchboard when the ambient temperature
They are specially recommended in difficult, highly These devices control the temperature inside the
is too low or to prevent the formation of condensation.
polluted environments where there is no external air enclosure and include an alarm function for signalling
circuit. operational anomalies.
YES YES
Small dimensions.
E quipped with a PTC-type heating system,
T
he temperature inside the enclosure does which stabilises the surface temperature
not depend on the external temperature. E
ven temperature inside the enclosure. of the aluminium profile.
T
he internal and external air circuits are H
igh protection rating: IP 54. Available in two versions: insulated with low surface
independent. U
se of an environmentally friendly gas. temperature or in aluminium when the surface
S
ecurity device against possible leaks. temperature is limited to 75 C.
The fan-equipped resistances guarantee an even
temperature inside the enclosure.
A
cold-water supply source is required. Installation of a drain is recommended.
S
pecific pumping installation. M aintenance required: filter replacement.
65
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Cooling unit
Side-mounting models Top-mounting models
External External
dimensions Control Reference dimensions Control Reference
(mm) (mm)
450 X 350 X 140 Thermostat NSYCU240W230VL 340 X 600 X 350 Thermostat NSYCU760W230VR
620 X 300 X 170 Thermostat NSYCU370W230VL 400 X 700 X 400 Thermostat NSYCU1050W230VR
800 X 350 X 195 Thermostat NSYCU760W230VL 415 X 750 X 412 Electronic controller NSYCUE1400W230R
900 X 400 X 195 Thermostat NSYCU1050W230VL 400 X 700 X 400 Thermostat NSYCU1460W230VR
1010 X 400 X 240 Electronic controller NSYCUE1100W230L 430 X 700 X 400 Thermostat NSYCU1650W230VR
1010 X 400 X 240 Electronic controller NSYCUE1400W230L 415 X 750 X 412 Electronic controller NSYCUE1800W400R
1010 X 400 X 240 Electronic controller NSYCUE1400W400L 430 X 700 X 400 Thermostat NSYCU2000W400VR
1000 X 400 X 220 Thermostat NSYCU1650W230VL
470 X 800 X 450 Thermostat NSYCU2450W400VR
1000 X 400 X 220 Thermostat NSYCU1800W400VL
470 X 800 X 450 Thermostat NSYCU3100W400VR
1010 X 400 X 240 Electronic controller NSYCUE1800W400L
1406 X 502 X 300 Thermostat NSYCU2500W400VL
1406 X 502 X 300 Thermostat NSYCU4000W400VL
Covers
RAL 7035 Stainless-steel
Surface-mounting Partial flush-mounting Flush-mounting Surface-mounting Partial flush-mounting Flush-mounting
NSYCUCL NSYCUCH NSYCUCF NSYCUCLX NSYCUCHX NSYCUCFX
66
Thermal optimisation solutions Selection guide
Resistance heaters
Insulated resistance heater with fan Thermofans
Power (W) Voltage (V) Reference Power (W) Voltage (V) Reference
177 230 AC NSYCR170W230VVC 350 230 AC NSYCR350W230VTVC
400/550 120 AC NSYCRP1W120VTVC
400/550 230 AC NSYCRP1W230VTVC
Control temperature
Control a resistance heater
Control a fan or an alarm
or an alarm
Electronic hygrotherm 3
7 different operating modes. different operating modes.
Electronic thermostat Option of installing one or two external sensors. Option of installing an external sensor.
Reference
20%80% % RH NSYCCOHY230VID
NSYCCAST
67
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Automotive x x x x
nuclear x x x x
Food-processing
(lactic, sugar, beer, x x x x
wine etc.)
Chemicals x x
Foundry (glass, x
x x x (If ovens nearby, must insulate
metal etc.) to avoid radiation)
Transport x x
Treatment of water
or water source, x x x
pumping
Recycling x x x
Packaging x x
Cementary x x
Hoisting x x x x
Conveying x x x x
Closed premises
x x x
low-volume
Very hot location x x x x
Outdoors x x x x x
Sheet metal industry x x x x
x
(the effect of solar radiation, which
Telecoms x x x x x supplies calories to the cabinet,
must always be taken into account)
Use of "Passive" solutions
is always appropriate but more
68
Thermal optimisation solutions Thermal solutions & atmosphere
Circulation inside
the cabinet (with cabinet Use of thermal
closed) => solution valid Forced control teams
Air-air Air-water
only for low loads or ventilation Cooling Units Heaters (Thermostat
exchangers exchangers
to avoid heating premises + filters removed Hygrostat,
and homogenizing Hygrotherm)
the temperature)
x x x x x
x x x x x
x x
x
(If ventilation used,
must use OEM filters x x
for atmospheres where
oil is present)
x x x x x
x x x x x
x x
x x
x x x x
x x x x
x x
x x x x x
x x x x x
x x
x x
x x x x x x
x x x x x x
x x x x x x
Considerable energy
consumption and filter
Filter maintenance. Reliant on a chilled
Low heat extraction maintenance required
A lack of filter water source
power indoors. to prevent drop in
maintenance leads (or a chiller or a water
They rely on a high dT performance of cooling
to filter blockage source). Water must be
(minimum10 C) units. Example: mineral
and a reduction in flow filtered in order not to
to be effective. water production.
and performance. block the exchanger.
It is the most watertight
solution.
69
Control Panel - Technical Guide How to reduce damage to components through effective thermal management
Notes
70
Notes
71
Make the most of your energy
2011 - Schneider Electric - All rights reserved
www.schneider-electric.com
CPTG001_EN 10-2011