Quick Guide to Precision Measuring Instruments

Vibration Measuring Instruments

Vibration Terminology
Important parameters relating to vibration pickups/vibrometers are (3) Velocity Unit: m/s, cm/s, mm/s Symbol: V, v
described below: Refers to the maximum speed reached by a vibrating object during
(1) Vibration frequency Unit: Hz (Hertz) Symbol: f the vibration cycle in the direction of motion. Defined by the rate
Refers to the number of times a vibrating object vibrates per second. of change in displacement per unit time. Velocity may be measured
The inverse of a vibration frequency is referred to as the period directly but is often derived from a measurement of acceleration, and
(T), T=1/f. Incidentally, vibration frequency is also referred to as may also be derived from measuring displacement with respect to
frequency, and the motion is assumed to be sinusoidal. time, as below.
When discussing vibration of a rotating object, the relation between Example of notation in the
the number of rotations (rpm: revolutions per minute) and the v = ds/dt = d (D sin wt) / dt catalog:
frequency is as follows, where rpm is a non-SI unit (SI unit: min1). 0.001 - 19.99cm/s o-p
Example: 1200rpm/60s=20Hz
Frequency of an object rotating at 1200 revolutions per minute is Merit of velocity measurement
20Hz. Velocity is a parameter widely used for equipment diagnosis and
closely related to the fatigue failure of equipment structures. It is
discussed in ISO standards as a parameter for specifying the severity
s of vibration.
Example of notation in the
D
2D t
catalog: (4) Acceleration Unit: m/s2, cm/s2, mm/s2 Symbol: A, a
0.001 - 19.99mmp-p Refers to the rate at which the velocity of an object changes per unit
time. Acceleration is often measured directly and may also be derived
T=1/f from measuring velocity, or displacement (with respect to time) as
(2) Displacement Unit: m, mm, m Symbol: D, s below.
Refers to the distance a vibrating object is displaced from a Example of notation
reference position (normally, the stationary position). a = dv/dt = d2s/dt2 = d2 (D sin wt) / dt2 in the catalog:
s = D sin wt 0.01-199.9 cm/s2 o-p
"D" is implied when displacement is simply referred to as Merit of acceleration measurement
amplitude. However, "2D" is customarily used in many cases to Acceleration is regarded as a parameter effective for assessing the
refer to the peak-to-peak amplitude. likelihood of dynamic fracture, and is widely used as a means of
Half-amplitude D, 0-p (zero-to-peak) handling the fracture or breakdown especially of an object rotating at
Full-amplitude 2D, p-p (peak-to-peak) high speed.

Selection Guide to Vibration Transducers (Pickups)

Acceleration pickup applications from everyday to aerospace
High

Ship (Engine) Aviation/Space

(Measuring mechanical
vibration of engines
and the like)
DANGER Anti-shock inspection Safety and reliability enhancement of vehicles
of nuclear power plants
(Airbag, traction control)
Development/inspection
of sporting goods Driving experience of vehicles
(Racket, helmet) (Engine, traveling performance,
ride quality, effect on loads)
Acceleration

Measuring vibration pollution Safety/pollution

(Railway, road, (Vibration check
civil engineering of handheld tools)
Equipment checks
work, factory) Vibration control, seismic (Leakage of in-plant piping,
isolation, inspection, abnormality of rotating machinery)
diagnosis of buildings

Device protection, interlock

Transportation related vibration monitoring (Protection of hard disk head)

Surveillance and maintenance

Geological survey of electric power facilities
(Power plant - power transmission - Ultra-precision processing
transformation)
Low

Seismometer, seismic observation (Semiconductor exposure line)

Low Frequency High

Servo acceleration pickup

Vibration pickup

Piezoelectric acceleration pickup

Electrokinetic velocity pickup
Non-contact displacement pickup

DC 0.1 1 10 100 1000 10000 Frequency Hz

Quick Guide to Precision Measuring Instruments 46

 Seismogram Chart
Illustration of usage

D: Displacement (mm) at half amplitude

v: Velocity (cm/s)
g: Acceleration (stated as a fraction of go, the standard acceleration of
gravity at the Earths surface)
f: Frequency (Hz)
ft: Frequency (Hz) determined by a given displacement and acceleration

Relation between Relation between Relation between

v-f-D v-f-g D-g-ft
v D
v G g
D

f f ft
* The seismogram chart allows the magnitude of any one parameter to be determined from the
magnitudes of two other parameters.

Selection Guide to Vibration Pickups and Model of Vibrometers

Field of application Purpose Specification requirements Recommended type
Industrial machinery Operating conditions monitoring For measuring the vibration induced by rotating/reciprocating Piezoelectric acceleration pickup/vibrometer
Machine tools abnormality motions through the use of gears and rolling bearings and its
Vibration observation wide vibration range of harmonics.
Equipment diagnosis A vibration pickup is required of a size that does not affect the
Evaluation of bearings frequency characteristics of an object to be measured.
High frequency characteristics (10 kHz) are required.
High-speed rotating For measuring the unbalance and coupling abnormality Electrokinetic velocity pickup/vibrometer
machinery resulting from the rotating motion through the use of a sliding
Internal combustion engines bearing.
Power plant turbine Abnormal vibration observation For monitoring vibrations in the normal state. Non-contact displacement pickup/vibrometer
Generator peripherals/ac- For non-contact measurement of rotating shafts.
cessories For measuring vibrations of a casing.
For measuring relatively low frequency in terms of velocity and
displacement. Mainly electrokinetic velocity pickup/ vibrometer
Transportation machinery Safety evaluation For measuring low-velocity vibrations. Servo acceleration pickup/vibrometer
Automobile/ship/aircraft Riding quality evaluation Electrokinetic velocity pickup (compact type)/
vibrometer
For measuring high frequencies and noise levels. Piezoelectric acceleration pickup (extra compact
type)/vibrometer
Large-scale structures Dynamic stiffness evaluation For measuring in a low frequency range while putting the prior- Servo acceleration pickup/vibrometer
Anti-earthquake design data ity to the sensitivity over the magnitude of the output.
Building structures Environmental measurement
Seismic diagnosis (earthquake resis-
tance diagnosis)
Ground disturbance Seismic observation For measuring mainly in the low frequency range below 50Hz Electrokinetic velocity pickup/vibrometer
Vibration pollution research where precision measurement of vibration levels to lower than Servo acceleration pickup/vibrometer
Machinery foundation research a few Gals is required. (m/s2=100Gal)
Various vibration testing Research and development If a pickup for the entire range of frequency is required, select Piezoelectric acceleration pickup/vibrometer
Dynamic stiffness/frequency character- multiple pickups according to the purpose. Electrokinetic velocity pickup/vibrometer
istics evaluation For the purpose of motion control of equipment. Servo acceleration pickup/vibrometer
Pickup Portable vibrometer (Ground noise meter) Vibration monitoring machine
Servo V405, 407 AVT-103/104 AVR-145L
Piezoelectric V311TE, TB, SB, TF, V301SS, TA, TB, SB, TC, TD, V331TB AVT-CZ, AVT-3000DZ, AHV-1000AZ AVR-145Z
V238J, V231, V233, V237L, V240V, V242T, U1-FH, U1-FH-S,
Electrokinetic AVT-B2, AHV-1000BU, AHV-11A AVR-145, 150
U1-FMA, V235B, V241 251M, 2516, V251GV (H), (L1), (L2)
Non-contact V462B-8, MX AVR-145X

47 Quick Guide to Precision Measuring Instruments