Bull ESCALA

PCIX SCSI RAID Controller

Reference Guide

ORDER REFERENCE
86 A1 22EM 00
Bull ESCALA
PCIX SCSI RAID Controller
Reference Guide

Hardware

November 2003

BULL CEDOC
357 AVENUE PATTON
B.P.20845
49008 ANGERS CEDEX 01
FRANCE

ORDER REFERENCE
86 A1 22EM 00
The following copyright notice protects this book under the Copyright laws of the United States of America
and other countries which prohibit such actions as, but not limited to, copying, distributing, modifying, and
making derivative works.

Copyright Bull S.A. 1992, 2003

Printed in France

Suggestions and criticisms concerning the form, content, and presentation of

this book are invited. A form is provided at the end of this book for this purpose.

To order additional copies of this book or other Bull Technical Publications, you
are invited to use the Ordering Form also provided at the end of this book.

Trademarks and Acknowledgements

We acknowledge the right of proprietors of trademarks mentioned in this book.

AIXR is a registered trademark of International Business Machines Corporation, and is being used under
licence.

UNIX is a registered trademark in the United States of America and other countries licensed exclusively through
the Open Group.

Linux is a registered trademark of Linus Torvalds.

The information in this document is subject to change without notice. Bull will not be liable for errors contained
herein, or for incidental or consequential damages in connection with the use of this material.
Contents
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Handling Static Sensitive Devices . . . . . . . . . . . . . . . . . . . . . . . . . vii

About This Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

ISO 9000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Highlighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
References to AIX Operating System . . . . . . . . . . . . . . . . . . . . . . . . . ix
Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Chapter 1. PCI-X SCSI RAID Controller Overview . . . . . . . . . . . . . . . . . . . . 1

Disk Arrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Supported RAID Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
RAID Level 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
RAID Level 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
RAID Level 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Disk Array Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
RAID Level Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Stripe-Unit Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Disk Array Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
States for Disk Arrays (hdisks) . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
States for Physical Disks (pdisks) . . . . . . . . . . . . . . . . . . . . . . . . . . 9
pdisk Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 2. PCI-X SCSI RAID Controller Software . . . . . . . . . . . . . . . . . . . . 11

Verifying the Installation of the PCI-X SCSI RAID Controller Software . . . . . . . . . . . . . 11

Chapter 3. Common PCI-X SCSI RAID Controller Tasks . . . . . . . . . . . . . . . . . 13

Using the PCI-X SCSI Disk Array Manager . . . . . . . . . . . . . . . . . . . . . . . 13
Preparing Disks for Use in PCI-X SCSI Disk Arrays . . . . . . . . . . . . . . . . . . . . 14
Creating a PCI-X SCSI Disk Array . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Viewing the Disk Array Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 15
Deleting a PCI-X SCSI Disk Array . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Adding Disks to an Existing Disk Array . . . . . . . . . . . . . . . . . . . . . . . . 17
Using Hot Spare Disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Creating Hot Spare Disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Deleting Hot Spare Disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Viewing and Changing PCI-X SCSI RAID Controller Bus Settings . . . . . . . . . . . . . . . 19
Viewing PCI-X SCSI Disk Array Settings . . . . . . . . . . . . . . . . . . . . . . . . 21
Viewing PCI-X SCSI pdisk Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Chapter 4. PCI-X SCSI RAID Controller Maintenance . . . . . . . . . . . . . . . . . . 23

Dos and Donts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Updating the PCI-X SCSI RAID Controller Microcode . . . . . . . . . . . . . . . . . . . 24
Changing pdisks to hdisks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Rechargeable Battery Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Displaying Rechargeable Battery Information . . . . . . . . . . . . . . . . . . . . . 24
Forcing a Rechargeable Battery Error . . . . . . . . . . . . . . . . . . . . . . . . 26
Replacing the Rechargeable Cache Battery Pack . . . . . . . . . . . . . . . . . . . . 26
Replacing pdisks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Recovery Procedures for Disk Failures . . . . . . . . . . . . . . . . . . . . . . . . 28
RAID Level 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

iii
 RAID Level 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
RAID Level 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Chapter 5. Problem Determination and Recovery . . . . . . . . . . . . . . . . . . . . 31

Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Location Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Identifying the Disk Array Problem . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Service Request Number (SRN) Table . . . . . . . . . . . . . . . . . . . . . . . . 32
Maintenance Analysis Procedures (MAPs) . . . . . . . . . . . . . . . . . . . . . . . 34
MAP 3000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
MAP 3010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
MAP 3011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
MAP 3012 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
MAP 3013 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
MAP 3020 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
MAP 3021 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
MAP 3030 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
MAP 3031 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
MAP 3032 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
MAP 3033 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
MAP 3034 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
MAP 3035 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
MAP 3036 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
MAP 3050 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
MAP 3051 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
MAP 3090 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Finding an SRN Given an AIX Error Log . . . . . . . . . . . . . . . . . . . . . . . 64
Example AIX Error Log (Error ID = SISIOA_ARY_DEGRADED) . . . . . . . . . . . . . . 64

Appendix A. Communications Statements . . . . . . . . . . . . . . . . . . . . . . 67

Federal Communications Commission (FCC) Statement . . . . . . . . . . . . . . . . . . 67
European Union (EU) Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
International Electrotechnical Commission (IEC) Statement . . . . . . . . . . . . . . . . . 67
United Kingdom Telecommunications Safety Requirements . . . . . . . . . . . . . . . . . 67
Avis de conformit aux normes du ministre des Communications du Canada . . . . . . . . . . 68
Canadian Department of Communications Compliance Statement . . . . . . . . . . . . . . 68
VCCI Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Electromagnetic Interference (EMI) Statement - Taiwan . . . . . . . . . . . . . . . . . . 68
Radio Protection for Germany . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Appendix B. Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Appendix C. AIX Command-Line Interface . . . . . . . . . . . . . . . . . . . . . . 73

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

iv PCI-X SCSI RAID Controller: Reference Guide for AIX

Safety Information
DANGER
An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of
the system or the devices that attach to the system. It is the responsibility of the customer to
ensure that the outlet is correctly wired and grounded to prevent an electrical shock.

Before installing or removing signal cables, ensure that the power cables for the system unit
and all attached devices are unplugged.

When adding or removing any additional devices to or from the system, ensure that the power
cables for those devices are unplugged before the signal cables are connected. If possible,
disconnect all power cables from the existing system before you add a device.

Use one hand, when possible, to connect or disconnect signal cables to prevent a possible
shock from touching two surfaces with different electrical potentials.

During an electrical storm, do not connect cables for display stations, printers, telephones, or
station protectors for communication lines.

v
vi PCI-X SCSI RAID Controller: Reference Guide for AIX
Handling Static Sensitive Devices
Attention: Static electricity can damage this device and your system unit. To avoid damage, keep this
device in its anti-static protective bag until you are ready to install it. To reduce the possibility of
electrostatic discharge, follow the precautions listed below:
v Limit your movement. Movement can cause static electricity to build up around you.
v Handle the device carefully, holding it by its edges or its frame.
v Do not touch solder joints, pins, or exposed printed circuitry.
v Do not leave the device where others can handle and possibly damage the device.
v While the device is still in its anti-static package, touch it to an unpainted metal part of the system unit
for at least two seconds. (This drains static electricity from the package and from your body.)
v Remove the device from its package and install it directly into your system unit without setting it down. If
it is necessary to set the device down, place it on its static-protective package. (If your device is an
adapter, place it component-side up.) Do not place the device on your system unit cover or on a metal
table.
v Take additional care when handling devices during cold weather, as heating reduces indoor humidity
and increases static electricity.

vii
viii PCI-X SCSI RAID Controller: Reference Guide for AIX
About This Book
This book provides usage and maintenance information regarding the PCI-X SCSI RAID Controller.
Chapters 1 through 4 of this book contain general information that is intended for all users of this product.
Chapter 5 contains service information intended for a service representative specifically trained on the
system unit and subsystem being serviced. Use this book in conjunction with your specific system unit and
operating system documentation.

ISO 9000
ISO 9000 registered quality systems were used in the development and manufacturing of this product.

Highlighting
The following highlighting conventions are used in this book:

Bold Identifies commands, subroutines, keywords, files, structures, directories, and other items
whose names are predefined by the system. Also identifies graphical objects such as buttons,
labels, and icons that the user selects.
Italics Identifies parameters whose actual names or values are to be supplied by the user.
Monospace Identifies examples of specific data values, examples of text similar to what you might see
displayed, examples of portions of program code similar to what you might write as a
programmer, messages from the system, or information you should actually type.

References to AIX Operating System

This document may contain references to the AIX operating system. If you are using another operating
system, consult the appropriate documentation for that operating system.

This document may describe hardware features and functions. While the hardware supports them, the
realization of these features and functions depends upon support from the operating system. AIX provides
this support. If you are using another operating system, consult the appropriate documentation for that
operating system regarding support for those features and functions.

Related Publications
The following publications contain related information:
v System unit documentation for information specific to your hardware configuration
v Adapters Information for Multiple Bus Systems, order number 86 A1 26HX, contains information about
adapters for you system.,
v Diagnostic information for Multiple Bus Systems, order number 86 A1 27HX, contains diagnostic information,
service request numbers (SRNs), and failing function codes (FFCs).
. AIX Syatem Management Guide: Operating System and Devices, order number 86 A2 26EF
v AIX Installation Guide and Reference, order number 86 A2 07EG.

ix
x PCI-X SCSI RAID Controller: Reference Guide for AIX
Chapter 1. PCI-X SCSI RAID Controller Overview
The PCI-X SCSI RAID Controller is a 133 MHz 64-bit PCI-X adapter. This adapter has the following
features:
v PCI-X system interface
v Dual Channel, Ultra320 SCSI controllers
v Embedded PowerPC RISC Processor and Hardware XOR DMA Engine
v Non-volatile write cache
v Support for RAID (Redundant Array of Independent Disks) levels 0, 5, and 10 disk arrays
v Disk array supported as a bootable device
v Supports attachment of other devices such as non-RAID disks, tape, and optical devices
v Advanced RAID features:
Hot spares for RAID level 5 and 10 disk arrays
Ability to increase the capacity of an existing RAID level 5 disk array by adding disks
Background parity checking
Background data scrubbing
Disks formatted to 522 bytes/sector, providing Longitudinal Redundancy Checking (LRC) and
Logically Bad Block checking

Note: Multi-initiator and High Availability (for example, HACMP) support is not provided at this time.

Feature Code PCI Form Factor Write Cache Size Adapter Rechargeable Cache Battery
LED/FFC Battery Pack FFC
Technology
5703 Yes 40 MB 2523 NiMH 2526
* **
5709 No 16 MB 2523 NiMH 2526
*
The feature code describes the RAID Enablement Card.
**
Some PCI-X SCSI RAID Controllers do not have the form of a standard PCI adapter. The form of these controllers
is a combination of SCSI and PCI-X bus interface logic integrated onto the system board and a RAID Enablement
Card. The card plugs into the system board in order to connect to the SCSI and PCI-X bus interface logic.

Note: This guide refers to various hardware and software features and functions. The realization of these
features and functions depends on the limitations of your hardware and software. AIX supports all
functions mentioned. If you are using another operating system, consult the appropriate
documentation for that operating system regarding support for the mentioned features and
functions. This guide also uses the terms channel and bus interchangeably.

1
Figure 1. PCI-X SCSI RAID Controller

1 Channel 1 external, 68-position, VHDCI (very high density cable interconnect)

2 Channel 0 external, 68-position, VHDCI (very high density cable interconnect)
3 Channel 0 internal, 68-position, high-density plastic D-shell SCSI standard connector for 16-bit
attachment
4 Channel 1 internal, 68-position, high-density plastic D-shell SCSI standard connector for 16-bit
attachment
5 Adapter Handle

Disk Arrays
RAID technology is used to store data across a group of disks known as a disk array. Depending on the
RAID level selected, this storage technique provides the data redundancy required to keep data secure
and the system operational. If a disk failure occurs, the disk can usually be replaced without interrupting
normal system operation. Disk arrays also have the potential to provide higher data transfer and input and
output (I/O) rates than those provided by single large disks.

Each disk array can be used by AIX in the same way as it would a single non-RAID disk. For example,
after creating a disk array, you can create a file system on the disk array or use AIX commands to make
the disk array available to the system by adding the disk array to a volume group.

The PCI-X SCSI RAID Controller is managed by the PCI-X SCSI Disk Array Manager. The PCI-X SCSI
Disk Array Manager serves as the interface to the RAID configuration. It is also responsible for the
monitoring and recovery features of the controller.

If a disk array is to be used as the boot device, it may be required to prepare the disks by booting from
the Diagnostic CD and creating the disk array before installing AIX. You might want to perform this
procedure when the original boot drive is to be used as part of a disk array.

2 PCI-X SCSI RAID Controller: Reference Guide for AIX

The following figure illustrates a possible disk array configuration.

Supported RAID Levels

The RAID level of a disk array determines how data is stored on the disk array and the level of protection
that is provided. When a part of the RAID system fails, different RAID levels help to recover lost data in
different ways. With the exception of RAID level 0, if a single drive fails within an array, the array controller
can reconstruct the data for the Failed disk by using the data stored on other hard drives within the array.
This data reconstruction has little or no impact to current system programs and users. The PCI-X SCSI
RAID Controller supports RAID levels 0, 5, and 10. Each RAID level supported by the PCI-X SCSI RAID
Controller has its own attributes and uses a different method of writing data. The following information
details each supported RAID level.

Chapter 1. PCI-X SCSI RAID Controller Overview 3

RAID Level 0
RAID level 0 stripes data across the disks in the array, for optimal performance. For a RAID level 0 array
of three disks, data would be written in the following pattern.

Figure 2. RAID Level 0

RAID level 0 offers a high potential I/O rate, but it is a nonredundant configuration. As a result, there is no
data redundancy available for the purpose of reconstructing data in the event of a disk failure. There is no
error recovery beyond what is normally provided on a single disk. Unlike other RAID levels, the array
controller never marks a RAID level 0 array as Degraded as the result of a disk failure. If a physical disk
fails in a RAID level 0 disk array, the disk array is marked as Failed. All data in the array must be backed
up regularly to protect against data loss.

4 PCI-X SCSI RAID Controller: Reference Guide for AIX

RAID Level 5
RAID level 5 stripes data across all disks in the array. RAID level 5 also writes array parity data. The parity
data is spread across all the disks. For a RAID level 5 array of three disks, array data and parity
information are written in the following pattern:

Figure 3. RAID Level 5

If a disk fails in a RAID level 5 array, you can continue to use the array normally. A RAID level 5 array
operating with a single Failed disk is said to be operating in Degraded mode. Whenever data is read from
a Degraded disk array, the array controller recalculates the data on the Failed disk by using data and
parity blocks on the operational disks. If a second disk fails, the array will be placed in the Failed state and
will not be accessible.

Chapter 1. PCI-X SCSI RAID Controller Overview 5

RAID Level 10
RAID level 10 uses mirrored pairs to redundantly store data. The array must contain an even number of
disks. The data is striped across the mirrored pairs. For example, a RAID level 10 array of four disks
would have data written to it in the following pattern:

Figure 4. RAID Level 10

RAID level 10 tolerates multiple disk failures. If one disk in each mirrored pair fails, the array will still be
functional, operating in Degraded mode. You can continue to use the array normally because for each
Failed disk, the data is stored redundantly on its mirrored pair. However, if both members of a mirrored
pair fail, the array will be placed in the Failed state and will not be accessible.

When a RAID level 10 disk array is created, the controller will automatically attempt to select the disks for
each mirrored pair from a different SCSI bus. For example, if four disks selected for the disk array reside
on one of the controllers SCSI buses and another four disks selected reside on another of the controllers
SCSI buses, the controller will automatically attempt to create each mirrored pair from one disk on each
SCSI bus. In the event of a SCSI bus failure, each mirrored pair will continue to operate in a Degraded
mode.

6 PCI-X SCSI RAID Controller: Reference Guide for AIX

Disk Array Capacities
The capacity of a disk array depends on the capacity of the disks used and the RAID Level of the array.
To calculate the capacity of a disk array, do the following:
RAID Level 0
Multiply the number of disks by the disk capacity.
RAID Level 5
Multiply one fewer than the number of disks by the disk capacity.
RAID Level 10
Multiply the number of disks by the disk capacity and divide by 2.

Note: If disks of different capacities are used in the same array, all disks are treated as if they have the
capacity of the smallest disk.

RAID Level Summary

The following information provides data redundancy, usable disk capacity, read performance, and write
performance for each RAID level.

RAID Level Data Redundancy Usable Disk Read Performance Write Performance
Capacity
RAID 0 None 100% Very Good Excellent
RAID 5 Very Good 67% to 94% Very Good Good
RAID 10 Excellent 50% Excellent Very Good

RAID Level 0
Does not support data redundancy, but provides a potentially higher I/O rate.
RAID Level 5
Creates array parity information so that the data can be reconstructed if a disk in the array fails.
Provides better capacity than RAID level 10 but possibly lower performance.
RAID Level 10
Stores data redundantly on mirrored pairs to provide maximum protection against disk failures.
Provides generally better performance than RAID level 5, but has lower capacity.

Stripe-Unit Size
With RAID technology, data is striped across an array of physical disks. This data distribution scheme
complements the way the operating system requests data. The granularity at which data is stored on one
disk of the array before subsequent data is stored on the next disk of the array is called the stripe-unit
size. The collection of stripe units, from the first disk of the array to the last disk of the array, is called a
stripe.

You can set the stripe-unit size of a PCI-X SCSI Disk Array to 16 KB, 64 KB, or 256 KB. You may be able
to maximize the performance of your PCI-X SCSI Disk Array by setting the stripe-unit size to a value that
is slightly larger than the size of the average system I/O request. For large system I/O requests, use a
stripe-unit size of 256 KB. The recommended stripe size for most applications is 64 KB.

Disk Array Overview

Disk arrays are groups of disks that work together with a specialized array controller to potentially achieve
higher data transfer and input and output (I/O) rates than those provided by single large disks. The array
controller keeps track of how the data is distributed across the disks. RAID level 5 and 10 disk arrays also
provide data redundancy, so that no data is lost if a single disk in the array fails.

Chapter 1. PCI-X SCSI RAID Controller Overview 7

PCI-X SCSI Disk Arrays are assigned names using the hdisk form, the same as other disk storage units in
AIX. These names are automatically assigned whenever you create a disk array. The names are deleted
when you delete the disk array. The individual physical disks that comprise disk arrays or serve as
candidates to be used in disk arrays are represented by pdisk names. A pdisk is a disk that is formatted to
522 bytes/sector. Disks that are formatted to 512 bytes/sector are assigned names using the hdisk form.
These disks must be formatted to 522 bytes/sector before they can be used in disk arrays. For additional
information about formatting 512 bytes/sector hdisks to make them available for use in PCI-X SCSI Disk
Arrays, see Preparing Disks for Use in PCI-X SCSI Disk Arrays on page 14.

The List PCI-X SCSI Disk Array Configuration option in the PCI-X SCSI Disk Array Manager can be
used to display these pdisk and hdisk names, along with their associated location codes. For details
regarding how to view the disk array information, see Viewing the Disk Array Configuration on page 15.
The following sample output is displayed when the List PCI-X SCSI Disk Array Configuration option is
invoked.

-----------------------------------------------------------------------------
Name Location State Description Size
-----------------------------------------------------------------------------
sisioa1 30-60 Available PCI-X Dual Channel U320 SCSI RAID Adapter

hdisk15 30-60-ff-0,1 Optimal Raid 5 Array 54.3GB

pdisk0 30-60-00-5,0 Active Array Member 18.1GB
pdisk1 30-60-00-6,0 Active Array Member 18.1GB
pdisk2 30-60-01-2,0 Active Array Member 36.4GB
pdisk4 30-60-01-3,0 Active Array Member 18.1GB

hdisk16 30-60-ff-0,2 Degraded Raid 5 Array 72.8GB

pdisk3 30-60-00-10,0 Active Array Member 36.4GB
pdisk5 30-60-01-5,0 Failed Array Member 36.4GB
pdisk6 30-60-00-11,0 Active Array Member 36.4GB

pdisk7 30-60-00-12,0 Active Array Candidate 36.4GB

pdisk8 30-60-00-13,0 Active Hot Spare 72.8GB

hdisk20 30-60-01-4,0 Available 16 Bit LVD SCSI 9.0GB

hdisk21 30-60-01-6,0 Defined 16 Bit LVD SCSI 9.0GB

The third column in the preceding output displays the state of the device.

States for Disk Arrays (hdisks)

The six valid states for PCI-X SCSI Disk Arrays are: Optimal, Degraded, Rebuilding, Failed, Missing, and
Unknown.
Optimal
The array is functional and fully protected (RAID 5 and 10) with all Array Member pdisks in the
Active state.
Degraded
The arrays protection against disk failures is degraded or its performance is degraded. When one
or more Array Member pdisks are in the Failed state, the array is still functional but is no longer
fully protected against disk failures. For more information about recovery procedures for disk
failures, see Recovery Procedures for Disk Failures on page 28. When all Array Member pdisks
are in the Active state, the array is not performing optimally because of a problem with the
controllers nonvolatile write cache.
Rebuilding
Redundancy data for the array is being reconstructed. After the rebuild process has completed, the
array will return to the Optimal state. Until then, the array is not fully protected against disk
failures.

8 PCI-X SCSI RAID Controller: Reference Guide for AIX

Failed The array is no longer accessible because of disk failures or configuration problems.
Missing
A previously configured disk array no longer exists.
Unknown
The state of the disk array could not be determined.

States for Physical Disks (pdisks)

The valid states for pdisks are: Active, RWProtected, Failed, Missing, and Unknown.
Active The disk is functioning properly.
RWProtected
The disk is unavailable because of a hardware or a configuration problem.
Failed The controller can not communicate with the disk or the pdisk is the cause of the disk array being
in a Degraded state.
Missing
The disk was previously connected to the controller but is no longer detected.
Unknown
The state of the disk could not be determined.

pdisk Descriptions
The fourth column in the preceding output is a description of the device. For an array, the description
indicates the RAID level of the array. The description of a pdisk indicates whether the disk is configured as
an Array Member, Hot Spare, or an Array Candidate.
Array Member
A 522 bytes/sector pdisk that is configured as a member of an array.
Hot Spare
A 522 bytes/sector pdisk that can be used by the controller to automatically replace a Failed disk
in a Degraded RAID level 5 or RAID level 10 disk array. A Hot Spare disk is useful only if its
capacity is greater than or equal to the capacity of the smallest disk in an array that becomes
Degraded. For more information about hot spare disks, see Using Hot Spare Disks on page 18.
Array Candidate
A 522 bytes/sector pdisk that is a candidate for becoming an Array Member or a Hot Spare.

Chapter 1. PCI-X SCSI RAID Controller Overview 9

10 PCI-X SCSI RAID Controller: Reference Guide for AIX
Chapter 2. PCI-X SCSI RAID Controller Software
For the PCI-X SCSI RAID Controller to be identified and configured by AIX, the requisite device support
software must be installed. The requisite software for the PCI-X SCSI RAID Controller is often preinstalled
as part of the normal AIX installation. However, it may be necessary to perform operations related to the
installation, verification, and maintenance of the AIX device software for the PCI-X SCSI RAID Controller.

Software for the PCI-X SCSI RAID Controller is packaged in installp format and distributed as part of the
base AIX installation media, AIX update media, and through the web-based Fix Delivery Center for AIX.
This information is an overview of the AIX software support required for the PCI-X SCSI RAID Controller.
For complete information related to the installation and maintenance of AIX, refer to the AIX Installation
Guide and Reference.

Note: Support of the PCI-X SCSI RAID Controller requires AIX Version 5.1 or later.

The PCI-X SCSI RAID Controller executes onboard microcode. The AIX command lsmcode can be used
to determine the level of onboard microcode being used by the controller. Although a version of controller
microcode may be distributed along with AIX, this does not necessarily represent the most recent version
of microcode available for the controller. For more information regarding obtaining and downloading new
PCI-X SCSI RAID Controller microcode, see Updating the PCI-X SCSI RAID Controller Microcode on
page 24.

Verifying the Installation of the PCI-X SCSI RAID Controller Software

Support for the PCI-X SCSI RAID Controller is contained in the AIX package devices.pci.14107802. The
device support package contains multiple filesets, each related to a different aspect of device support (for
example, run-time environment, diagnostics support, and controller microcode).

To verify that the device support package for the PCI-X SCSI RAID Controller is installed, type:
lslpp -l devices.pci.14107802*

Output from this command will indicate if device support software for the PCI-X SCSI RAID Controller is
installed, and if so, what the corresponding levels of each fileset are.

If the output indicates that no filesets of this name are installed, you must install the package
devices.pci.14107802 in order for the PCI-X SCSI RAID Controller to be made available for use. This
software package is available as part of the base AIX installation media, AIX update media, and through
the web-based Fix Delivery Center for AIX.

Over time, it may become necessary to install software updates in order to have the very latest available
level of device software support for the PCI-X SCSI RAID Controller. Updates to the device support
software are packaged, distributed, and installed through the same mechanisms used for other portions of
the AIX base operating system. The standard AIX technical support procedures can be used to determine
the latest available level of device software support for the PCI-X SCSI RAID Controller.

11
12 PCI-X SCSI RAID Controller: Reference Guide for AIX
Chapter 3. Common PCI-X SCSI RAID Controller Tasks
The instructions in this chapter pertain to the various tasks that can be performed in order to manage disk
arrays.

Using the PCI-X SCSI Disk Array Manager

The PCI-X SCSI Disk Array Manager can be accessed either through the System Management Interface
Tool (SMIT), or for some tasks, the AIX command line. For information about using the command line
interface, see Appendix C, AIX Command-Line Interface, on page 73. The PCI-X SCSI Disk Array
Manager can also be started from Diagnostics.

To start the PCI-X SCSI Disk Array Manager, do the following:

1. At the command prompt, type smit, and press Enter.
2. Select Devices.
3. Select Disk Array.
4. Select IBM PCI-X SCSI Disk Array. From the menu with options for configuring and managing the
PCI-X SCSI RAID Controller, select PCI-X SCSI Disk Array Manager to display the following menu for
managing disk arrays.
PCI-X SCSI Disk Array Manager
Move cursor to desired item and press Enter.

List PCI-X SCSI Disk Array Configuration

Create an Array Candidate pdisk and Format to 522 Byte Sectors
Create a PCI-X SCSI Disk Array
Delete a PCI-X SCSI Disk Array
Add Disks to an Existing PCI-X SCSI Disk Array
Configure a Defined PCI-X SCSI Disk Array
Change/Show Characteristics of a PCI-X SCSI Disk Array
Reconstruct a PCI-X SCSI Disk Array
Change/Show PCI-X SCSI pdisk Status
Diagnostics and Recovery Options

F1=Help F2=Refresh F3=Cancel F8=Image

F9=Shell F10=Exit Enter=Do

You can also use a SMIT fast path to start the PCI-X SCSI Disk Array Manager. On the AIX command line,
type smit pxdam, and press Enter.

If a disk array is to be used as the boot device, you might need to prepare the disks by booting from the
Diagnostic CD and creating the disk array before installing AIX. You might want to perform this procedure
when the original boot drive is to be used as part of a disk array.

To start the PCI-X SCSI Disk Array Manager from Diagnostics, do the following:
1. Start Diagnostics and on the Function Selection screen, select Task Selection.
2. Select RAID Array Manager and press Enter.
3. Select PCI-X SCSI Disk Array Manager and press Enter.

13
Preparing Disks for Use in PCI-X SCSI Disk Arrays
Before a disk can be used in a PCI-X SCSI Disk Array, it must be a 522 bytes/sector Array Candidate
pdisk. To create an Array Candidate pdisk and format it to 522 byte sectors, do the following:
1. Start the PCI-X SCSI Disk Array Manager by following the steps in Using the PCI-X SCSI Disk Array
Manager on page 13.
2. Select Create an Array Candidate pdisk and Format to 522 Byte Sectors.
3. Select the appropriate PCI-X SCSI RAID Controller.
4. Select the disks that you want to prepare for use in the PCI-X SCSI Disk Arrays.
Attention: Continuing with this option will format the disks. All data on the disks will be lost. Some
disks require that their microcode be updated to the latest level before being formatted to 522 byte
sectors. Also, some disks do not support being formatted to 522 byte sectors. The PCI-X SCSI Disk
Array Manager will inform the user of these situations when they exist.
5. A message will display asking if you want to continue. To proceed with the format, select OK or press
Enter to continue. To return to the previous menu without formatting the disks, select Cancel.

After the formatting is complete, the disks will be Array Candidate pdisks and will be ready for use in
PCI-X SCSI Disk Arrays. This operation will also zero all the data on the disks. The PCI-X SCSI RAID
Controller keeps track of the disks that have their data zeroed. These Zeroed Array Candidate pdisks can
be used to create a disk array that will be immediately protected against disk failures, and they are the
only disks that can be added to an existing disk array. An Array Candidate pdisk will lose its Zeroed state
after it has been used in an array or is unconfigured. It will also lose its Zeroed state after the system has
been rebooted. To return an Array Candidate pdisk to the Zeroed state, follow the steps previously
described in this section for preparing disks for use in disk arrays.

Creating a PCI-X SCSI Disk Array

A disk array is created using a set of Active Array Candidate pdisks. For disk arrays with data redundancy
(RAID level 5 and RAID level 10), if all of the pdisks are in the Zeroed state, the array will become
immediately protected against failures. However, if one or more of the pdisks are not Zeroed, the newly
created array will initially be in the Rebuilding state. It will be unprotected against disk failures until parity
data on all of the disks has been recalculated. For disk arrays with no data redundancy (RAID level 0), it is
of no importance whether the pdisks are in the Zeroed state. To create a PCI-X SCSI Disk Array, do the
following:
1. Start the PCI-X SCSI Disk Array Manager by following the steps in Using the PCI-X SCSI Disk Array
Manager on page 13.
2. Select Create a PCI-X SCSI Disk Array.
3. Select the appropriate PCI-X SCSI RAID Controller on which you want to create an array.
4. Select the RAID level for the array. For more information about selecting an appropriate RAID level,
see Supported RAID Levels on page 3.
5. Select the stripe size in kilobytes for the array. For more information about the stripe-size parameter,
see Stripe-Unit Size on page 7. A selection screen similar to the following displays. It will display a list
of Array Candidate pdisks and notes regarding array requirements. The minimum and maximum
number of supported disks will be specified, along with any other specific requirements for the array.
6. Select the disks that you want to use in the array according to the requirements on this screen.

14 PCI-X SCSI RAID Controller: Reference Guide for AIX

 Create a PCI-X SCSI Disk Array
Move cursor to desired item and press F7. Use arrow keys to scroll.
ONE OR MORE items can be selected.
Press Enter AFTER making all selections.

# RAID 10 supports a minimum of 2 and a maximum of 18 disks

# The total number of disks must be a multiple of 2

pdisk10 30-60-01-1,0 Active Array Candidate 72.8GB

pdisk11 30-60-00-4,0 Active Array Candidate 72.8GB
pdisk12 30-60-01-8,0 Active Array Candidate 72.8GB
pdisk18 30-60-00-2,0 Active Array Candidate 72.8GB

F1=Help F2=Refresh F3=Cancel

F7=Select F8=Image F10=Exit
Enter=Do /=Find n=Find Next

7. A SMIT Dialog Screen summarizes your selections. Press Enter to create the array.

You can now add the disk array to a volume group. Logical volumes and file systems can also be created.
Use standard AIX procedures to perform these tasks, and treat the array in the same way that you would
treat any hdisk.

Viewing the Disk Array Configuration

To view the configuration of arrays and disks associated with a particular PCI-X SCSI RAID Controller, do
the following:
1. Start the PCI-X SCSI Disk Array Manager by following the steps in Using the PCI-X SCSI Disk Array
Manager on page 13.
2. Select List PCI-X SCSI Disk Array Configuration.
3. Choose one or more PCI-X SCSI RAID Controllers. The output displayed will be similar to the
following:

Chapter 3. Common PCI-X SCSI RAID Controller Tasks 15

 COMMAND STATUS
Command: OK stdout: yes stderr: no

Before command completion, additional instructions may appear below.

------------------------------------------------------------------------
Name Location State Description Size
------------------------------------------------------------------------
sisioa1 30-60 Available PCI-X Dual Channel U320 SCSI RAID Adapter

hdisk11 30-60-ff-0,1 Optimal Raid 5 Array 54.3GB

pdisk0 30-60-00-5,0 Active Array Member 18.1GB
pdisk1 30-60-00-6,0 Active Array Member 18.1GB
pdisk2 30-60-01-2,0 Active Array Member 36.4GB
pdisk4 30-60-01-3,0 Active Array Member 18.1GB

hdisk12 30-60-ff-0,2 Degraded Raid 5 Array 72.8GB

pdisk3 30-60-00-10,0 Active Array Member 36.4GB
pdisk5 30-60-01-5,0 Failed Array Member 36.4GB
pdisk6 30-60-00-11,0 Active Array Member 36.4GB

hdisk13 30-60-ff-0,3 Rebuilding Raid 10 Array 72.8GB Create 55%

pdisk7 30-60-00-12,0 Active Array Member 72.8GB
pdisk8 30-60-01-12,0 Active Array Member 72.8GB

hdisk14 30-60-ff-0,6 Failed Raid 5 Array 109.2GB

pdisk14 30-60-00-0,0 RWProtected Array Member 36.4GB
pdisk15 30-60-00-9,0 RWProtected Array Member 36.4GB
pdisk16 30-60-00-2,0 Missing Array Member 36.4GB
pdisk17 30-60-00-3,0 Missing Array Member 36.4GB

hdisk15 30-60-ff-0,8 Missing Raid 0 Array 145.6GB

pdisk9 30-60-00-1,0 Active Hot Spare 18.1GB

pdisk10 30-60-01-1,0 Active Array Candidate 72.8GB
pdisk11 30-60-00-4,0 Active Array Candidate 72.8GB Zeroed
pdisk12 30-60-01-13,0 RWProtected Array Candidate 72.8GB Format 35%

hdisk20 30-60-01-4,0 Available 16 Bit LVD SCSI 9.0GB

hdisk21 30-60-01-6,0 Defined 16 Bit LVD SCSI 9.0GB

F1=Help F2=Refresh F3=Cancel F6=Command

F8=Image F9=Shell F10=Exit /=Find
n=Find Next

The controllers name, location, status, and description are displayed first. Each PCI-X SCSI disk array
hdisk is displayed with its Array Member pdisks directly underneath it.
v The first column of output is the name of the disk array (hdisk) or physical disk (pdisk).
v The second column of output is the devices location code. The format of the location code is
AB-CD-EF-G,H. The AB-CD fields identify the location of the PCI-X SCSI RAID Controller. The EF value
identifies the Controllers SCSI bus that the device is attached to. For a disk array this value will be ff
which indicates a logical bus for RAID devices. The G,H values are the SCSI ID and Logical Unit
Number (LUN) of the device.
v The third column of the above output is the state of the disk array or pdisk. For information about the
possible disk array and pdisk states, see Disk Array Overview on page 7. For 512 byte/sector
standalone disks (hdisks), this column is the AIX device state (for example, Available or Defined).
v The fourth column is a description of the device. For a disk array, the description is the RAID level of
the array. For a pdisk, the description can be Array Candidate, Hot Spare, or Array Member.
v The fifth column is the capacity of the array or disk. For information about how the capacity of an array
is calculated for each RAID level, see Disk Array Capacities on page 7.
v The sixth column is the status of a long-running command issued to a disk array or pdisk. This column
is also used to indicate that an Array Candidate pdisk has had its data zeroed. The following values
may be displayed:

16 PCI-X SCSI RAID Controller: Reference Guide for AIX

 Create nn%
Disk array is in process of being created.
Delete nn%
Disk array is in process of being deleted.
Rebuild nn%
Disk array is in process of being reconstructed.
Resync nn%
Disk array is in process of having it parity data resynchronized.
Adding nn%
Disk array is in process of having one or more disks added to it.
Format nn%
pdisk is in process of being formatted.
Zeroed
pdisk has been zeroed.

Array Candidate pdisks and Hot Spare pdisks are displayed at the bottom of this screen. The pdisk names
are displayed, along with location, state, description, capacity, and long-running command status. Any 512
bytes/sector standalone disks (hdisks) are displayed, along with location, state, description, and capacity.

Deleting a PCI-X SCSI Disk Array

Attention: After a disk array is deleted, it cannot be accessed. All data will be lost. A disk array that is
currently in use or opened cannot be deleted. Also, if a disk array command (such as a disk creation
command) is in progress, that disk array cannot be deleted.

To preserve the data on the disk array, you must first back up all files in the logical volumes and file
systems on the disk array before removing the disk array from its volume group. To delete the array, do
the following:
1. Start the PCI-X SCSI Disk Array Manager by following the steps in Using the PCI-X SCSI Disk Array
Manager on page 13.
2. Select Delete a PCI-X SCSI Disk Array.
3. Select the PCI-X SCSI RAID Controller.
4. Select the disk array to delete.

When the disk array has been deleted, any Active Array Member pdisks will become Active Array
Candidate pdisks.

Adding Disks to an Existing Disk Array

The PCI-X SCSI RAID Controller supports adding disks to existing RAID level 5 disk arrays, which allows
you to dynamically increase the capacity of a disk array while preserving its existing data. Extensive use of
this feature, however, will result in a performance penalty; because the added disks will not contain parity
and the data will not be restriped.

An Array Candidate pdisk is not necessarily a candidate that can be added to an existing array. In addition
to being an Array Candidate, the pdisk must also be recognized by the adapter as having its data zeroed.
This situation ensures that when the disks are added to the array, the parity data will be correct and the
array will remain protected against disk failures.

To add disks to an existing array, do the following:

Chapter 3. Common PCI-X SCSI RAID Controller Tasks 17

1. Ensure that the disks to be added are Zeroed Array Candidate pdisks. For assistance in viewing and
changing the state of the disk, see Preparing Disks for Use in PCI-X SCSI Disk Arrays on page 14
and Viewing the Disk Array Configuration on page 15.
2. Start the PCI-X SCSI Disk Array Manager by following the steps in Using the PCI-X SCSI Disk Array
Manager on page 13.
3. Select Add Disks to an Existing PCI-X SCSI Disk Array.
4. Select the PCI-X SCSI Disk Array to which you want to add disks.
5. A screen will display similar to the following example. If a particular disk is not included in the list, it
may not be a candidate that can be added to the array because of the following reasons:
v The disks capacity is less than that of the smallest disk already in the array.
v The disk has not been formatted as a 522 bytes/sector Array Candidate pdisk.
v The disk does not have its data zeroed.
For the second and third cases, the disk can be added to an array if it is first formatted using the
Create an Array Candidate pdisk and Format to 522 Byte Sectors option in the PCI-X SCSI Disk
Array Manager.
Add Disks to an Existing PCI-X SCSI Disk Array
Move cursor to desired item and press F7. Use arrow keys to scroll.
ONE OR MORE items can be selected.
Press Enter AFTER making all selections.

# Choose up to 14 of the following disks to add to hdisk2

pdisk10 30-60-01-1,0 Active Array Candidate 72.8GB Zeroed

pdisk11 30-60-00-4,0 Active Array Candidate 72.8GB Zeroed
pdisk12 30-60-01-8,0 Active Array Candidate 72.8GB Zeroed
pdisk18 30-60-00-2,0 Active Array Candidate 80.0GB Zeroed

# Note: If a disk is not listed here it is either not a candidate

# to be added to this array or it does not have its data zeroed
# Use the Create an Array Candidate pdisk and Format to 522 Byte
# Sectors option to format and zero the disk.

F1=Help F2=Refresh F3=Cancel

F7=Select F8=Image F10=Exit
Enter=Do /=Find n=Find Next

A screen summarizes your selections and indicates the performance penalty associated with this
option.
6. Press Enter to add the disks to the array. To enable higher level components in the system to use the
increased capacity of the disk array, additional steps might be needed.

Using Hot Spare Disks

Hot Spare disks are used to automatically replace Failed disks in a redundant RAID environment. Hot
spare disks are useful only if their capacity is greater than or equal to that of the smallest capacity disk in
an array that becomes Degraded.

Creating Hot Spare Disks

To create hot spare disks, do the following:
1. Start the PCI-X SCSI Disk Array Manager by following the steps in Using the PCI-X SCSI Disk Array
Manager on page 13.
2. Select Change/Show PCI-X SCSI pdisk Status.
3. Select Create a Hot Spare.
4. Select the appropriate PCI-X SCSI RAID Controller.

18 PCI-X SCSI RAID Controller: Reference Guide for AIX

5. Select the pdisks that you want to designate as hot spares. A screen summarizes your selections.
6. Press Enter to create the hot spares.

The disk state changes to Hot Spare. On subsequent disk failures, reconstruction of Failed disks will occur
automatically for RAID level 5 and RAID level 10 disk arrays.

Note: If there is a Degraded disk array at the time that a Hot Spare is configured, reconstruction of the
Failed disk begins automatically.

Deleting Hot Spare Disks

To delete a Hot Spare and change the disk to an Array Candidate pdisk, do the following:
1. Start the PCI-X SCSI Disk Array Manager by following the steps in Using the PCI-X SCSI Disk Array
Manager on page 13.
2. Select Change/Show PCI-X SCSI pdisk Status.
3. Select Delete a Hot Spare.
4. Select the appropriate PCI-X SCSI RAID Controller.
5. Select the hot spares to delete.

The Hot Spare becomes an Array Candidate pdisk.

Viewing and Changing PCI-X SCSI RAID Controller Bus Settings

To view and change settings for the PCI-X SCSI RAID Controller, do the following:
1. At the command prompt, type smit, and press Enter.
2. Select Devices.
3. Select Disk Array.
4. Select IBM PCI-X SCSI Disk Array.
5. Select Change/Show PCI-X SCSI RAID Controller Bus.
6. Select the PCI-X SCSI RAID Controller bus that you want to change settings on or view.
Change/Show Characteristics of a PCI-X SCSI RAID Controller Bus
Type or select values in entry fields.
Press Enter AFTER making all desired changes.

[Entry Fields]
SCSI Adapter scsi8
Description PCI-X U320 SCSI RAID >
Status Available
Location 30-60-00
Adapter card SCSI ID [7] +#
Wide bus enabled yes +
Maximum SCSI Bus Speed in MB/s 320 +
QAS (Quick Arbitration) Capability Enable +
Apply change to DATABASE only no +

F1=Help F2=Refresh F3=Cancel F4=List

F5=Reset F6=Command F7=Edit F8=Image
F9=Shell F10=Exit Enter=Do

A screen displays information about the controller bus. The last five attributes on the screen are
changeable. The following is information regarding each of the attributes:
Adapter card SCSI ID
Specifies the SCSI ID value that the controller will use to send commands as an initiator
device. If multi-initiators are supported, the SCSI ID that the controller responds to when acting

Chapter 3. Common PCI-X SCSI RAID Controller Tasks 19

 as a target device will be specified. This value is usually changed to avoid a conflict or
duplication of SCSI IDs among the controller and other devices on the SCSI bus. Before
cabling any new device to the SCSI bus, you should verify that the devices SCSI ID is unique.
If the controller does not support multi-initiators, 7 is the only valid value for the SCSI ID.

Note: Multi-initiator and High Availability (such as HACMP) support are not provided at this
time.
Wide bus enabled
Specifies whether the controller will negotiate with the device for a 16-bit data transfer width on
the SCSI bus. If Yes is specified, which is the default value, the controller negotiates for 16-bit
data transfers. Yes can be specified when an 8-bit device is connected through an 8-bit cable
to the SCSI connector. The No option sets the data transfer width to 8 bits. Use the No option
when older devices are connected that may not handle the wide data transfer request, WDTR,
messages properly. The WDTR messages are used to detect the data transfer width
capabilities of a device.
Maximum SCSI Bus Speed in MB/s
This attribute is used to limit the maximum speed in megabytes per second (MB/s) that the
adapter SCSI bus will use. Speed is negotiated between the adapter and SCSI devices. The
maximum negotiated speed cannot be greater than the Maximum SCSI Bus Speed in MB/s
value.
QAS (Quick Arbitration) Capability
This attribute is used to enable or disable the quick arbitration capability. Enabling QAS
capability does not guarantee that QAS will actually occur for any device on a SCSI bus.
Apply Change to Database only
Indicates whether the configuration changes should be applied only to the database or to both
the database and the current device operation. For devices that are in use and cannot be
changed, this allows the database to be changed for the device and the changes will take
effect the next time the system is rebooted.
7. After changing any PCI-X SCSI RAID Controller attribute, press Enter to make the desired changes.

20 PCI-X SCSI RAID Controller: Reference Guide for AIX

Viewing PCI-X SCSI Disk Array Settings
To view the settings for a PCI-X SCSI Disk Array, do the following:
1. Start the PCI-X SCSI Disk Array Manager by following the steps in Using the PCI-X SCSI Disk Array
Manager on page 13.
2. Select the Change/Show Characteristics of a PCI-X SCSI Disk Array option.
3. Select the desired PCI-X SCSI Disk Array.
4. A SMIT dialog screen displays the attributes of the selected array. The output displayed will be similar
to the following:

Change/Show Characteristics of a PCI-X SCSI Disk Array

Type or select values in entry fields.

Press Enter AFTER making all desired changes.

[Entry Fields]
RAID Array hdisk15
Description SCSI RAID 5 Disk Arra>
Status Available
Location 30-60-ff-0,1
Serial Number 12D0E934
Physical volume identifier none
Queue DEPTH 16
Size in Megabytes 109200
RAID Level 5
Stripe Size in KB 64

F1=Help F2=Refresh F3=Cancel F4=List

F5=Reset F6=Command F7=Edit F8=Image
F9=Shell F10=Exit Enter=Do

v The Physical volume identifier field is a unique value assigned to the hdisk if the disk array is a
member of a volume group. If the disk array is not a member of a volume group, this field value is none.
v The Queue DEPTH field is the depth of the command queue used for this disk array.
v The Size in Megabytes field represents the usable capacity of the disk array. For information about
calculating capacities for each RAID level, see Supported RAID Levels on page 3.
v The RAID Level field is the level of protection chosen for this array.
v The Stripe Size in KB field is the number of contiguous kilobytes which will be written to a single disk
before switching to the next disk in the disk array. It provides the host with a method to tune data
striping according to the typical I/O request size.

You cannot change any of the attributes on this screen. The RAID level and stripe size must be specified
when the array is created.

Viewing PCI-X SCSI pdisk Settings

To view the PCI-X SCSI pdisk settings, do the following:
1. Start the PCI-X SCSI Disk Array Manager by following the steps in Using the PCI-X SCSI Disk Array
Manager on page 13.
2. Select Change/Show PCI-X SCSI pdisk Status.
3. Select Change/Show PCI-X SCSI pdisk.
4. Select a pdisk from the list.
5. The following attributes are displayed:

Chapter 3. Common PCI-X SCSI RAID Controller Tasks 21

 Change/Show PCI-X SCSI pdisk
Type or select values in entry fields.
Press Enter AFTER making all desired changes.

[Entry Fields]
Disk pdisk3
Description Physical SCSI Disk Drive
Status Available
Location 30-60-00-10,0
Serial Number E3V1W93B
Vendor and Product ID IBM IC35L036UCDY10>
Service Level
Size in Megabytes 60400
Format Timeout in minutes [120] +#

F1=Help F2=Refresh F3=Cancel F4=List

F5=Reset F6=Command F7=Edit F8=Image
F9=Shell F10=Exit Enter=Do

The Size in Megabytes field represents the capacity of the pdisk.

To display a pdisks Vital Product Data (VPD), do the following:

1. Start the PCI-X SCSI Disk Array Manager by following the steps in Using the PCI-X SCSI Disk Array
Manager on page 13.
2. Select Change/Show PCI-X SCSI pdisk Status.
3. Select Display pdisk Vital Product Data.
4. Select the appropriate PCI-X SCSI RAID Controller.
5. Select the desired pdisk.

22 PCI-X SCSI RAID Controller: Reference Guide for AIX

Chapter 4. PCI-X SCSI RAID Controller Maintenance
This chapter provides information to assist in ensuring optimal performance of your PCI-X SCSI RAID
Controller.

Dos and Donts

To help avoid PCI-X SCSI RAID Controller and disk array problems, use the following tips :
v Always perform a normal system shutdown before physically replacing or moving the RAID adapter or
members of disk arrays. A normal shutdown of the system will flush the adapters write cache and
remove dependencies between the adapter and the pdisks. Using the rmdev command on the
controller (for example, rmdev -Rl sisioa3) has the same effect on the controller as it would on a single
adapter when the system shutdown command is used.

Note: pdisks that are a Failed member of a Degraded disk array can be replaced and the disk array
reconstructed while the system continues to run.
v You can physically move pdisks from one adapter to another. However, if the pdisks are members of a
disk array, be sure to move all the disks as a group. Prior to attempting a disk movement, ensure that
the disk array is not in a Degraded state because of a disk failure.
v When physically removing pdisks that are members of a disk array and there is no need to preserve
data and no intent to use the disk array again, delete the disk array before removing the disks. This
action avoids disk-array related problems the next time that these disks are used.
v Always use the SCSI and SCSI RAID Hot Plug Manager to remove and replace a pdisk. For
instructions on how to remove and replace a disk, see Replacing pdisks on page 27.
v If a disk array is being used as a boot device and the system fails to boot because of a suspected disk
array problem, boot using the Standalone Diagnostic media. Error Log Analysis, AIX error logs, the
PCI-X SCSI Disk Array Manager, and other tools are available on the Standalone Diagnostics to help
determine and resolve the problem with the disk array.
v Do not attempt to correct problems by swapping adapters and disks unless you are directed to do so by
the service procedures. Use Error Log Analysis to determine what actions to perform, and when
appropriate, follow the appropriate MAPs for problem determination. If multiple errors occur at
approximately the same time, look at them as a whole to determine if there is a common cause. For
additional information regarding problem determination, see Chapter 5, Problem Determination and
Recovery, on page 31.
v Do not confuse the Cache Directory Card, which is a small rectangular card with a round button-shaped
battery, for a cache card. The nonvolatile write cache memory is integrated into the main adapter card,
is not removable, and is battery-backed by the large, rechargeable Cache Battery Pack. The Cache
Directory Card contains only a secondary copy of the write cache directory, no cache data, and should
never be removed except under very specific cases as described in the MAPs.
v Do not unplug or exchange a Cache Battery Pack without following the procedures as outlined in this
section or in the MAPs.
v When invoking diagnostic routines for a PCI-X SCSI RAID Controller, it is recommended that Problem
Determination (PD) mode be used instead of System Verification (SV) mode unless there is a specific
reason to use SV mode (for example, you were directed to run SV mode by a MAP).
v After diagnostic routines for a PCI-X SCSI RAID Controller are run in SV mode, it is recommended to
run diagnostics in PD mode to ensure that new errors are analyzed. These actions should be performed
especially when using Standalone Diagnostic media.

23
Updating the PCI-X SCSI RAID Controller Microcode
To determine if an update is needed for your PCI-X SCSI RAID Controller, follow the directions at:
http://techsupport.services.ibm.com/server/mdownload/download.html. If updates are needed, download
instructions are also located at that Web address.

To install the update to a PCI-X SCSI RAID Controller, do the following:

1. Type smit and press Enter.
2. Select Devices.
3. Select Disk Array.
4. Select IBM PCI-X SCSI Disk Array.
5. Select Download Microcode to a PCI-X SCSI RAID Controller.
6. Select your PCI-X SCSI RAID Controller.
7. Follow the instructions to complete the update.

Changing pdisks to hdisks

To change Array Candidate pdisks (522 bytes/sector) to standalone hdisks (512 bytes/sector), you must
delete and format the pdisks.

Note: pdisks which are members of a disk array or are hot spares cannot be changed to standalone
hdisks.

To change the pdisks to standalone hdisks, do the following:

1. Navigate to the PCI-X SCSI Disk Array Manager by using the steps in Using the PCI-X SCSI Disk
Array Manager on page 13.
2. Select Change/Show PCI-X SCSI pdisk Status.
3. Select Delete an Array Candidate pdisk and Format to 512 Byte Sectors.
4. Select the appropriate PCI-X SCSI RAID Controller.
5. Select the 522 bytes/sector pdisks to be formatted to 512 bytes/sector standalone hdisks.
Attention: Continuing with this option will format the disks. All data on the disks will be lost.
When the format completes, the pdisk will be deleted and replaced by an hdisk.

Rechargeable Battery Maintenance

Rechargeable battery maintenance tasks described in this section include displaying rechargeable battery
information, forcing a rechargeable battery error, and replacing the rechargeable Cache Battery Pack.

Displaying Rechargeable Battery Information

To display information about the controllers rechargeable battery, do the following:
1. Navigate to the PCI-X SCSI Disk Array Manager by using the steps found in Using the PCI-X SCSI
Disk Array Manager on page 13.
2. Select Diagnostics and Recovery Options.
3. Select Controller Rechargeable Battery Maintenance.
4. Select Display Controller Rechargeable Battery Information.
5. Select the PCI-X SCSI RAID Controller.
6. The screen displayed will be look similar to the following example:

24 PCI-X SCSI RAID Controller: Reference Guide for AIX

 COMMAND STATUS
Command: OK stdout: yes stderr: no

Before command completion, additional instructions may appear below.

RAID Adapter . . . . . . . . . . . . : sisioa1

Battery Type . . . . . . . . . . . . : Nickel Metal Hydride (NiMH)
Battery State . . . . . . . . . . . . : No battery warning/error
Power-on time (days) . . . . . . . . : 256
Adjusted power-on time (days) . . . . : 288
Estimated time to warning (days) . . : 512
Estimated time to error (days) . . . : 768

F1=Help F2=Refresh F3=Cancel F6=Command

F8=Image F9=Shell F10=Exit /=Find
n=Find Next

The following are the fields displayed on the rechargeable battery information screen:
RAID Adapter
The name of the selected controller.
Battery Type
The type of rechargeable Cache Battery Pack.
Battery State
Indicates if an error condition currently exists related to the rechargeable Cache Battery Pack. The
possible values for this field are:
No battery warning/error
No warning or error condition currently exists.
Warning condition
A warning condition currently exists and an error has been logged.
Error condition
An error condition currently exists and an error has been logged.
Unknown
Information is not available to determine whether a warning or error condition currently
exists.
Power-on time (days)
Indicates the raw power-on time, in units of days, of the rechargeable Cache Battery Pack.
Adjusted power-on time (days)
Indicates the adjusted (prorated) power-on time, in units of days, of the rechargeable Cache
Battery Pack.

Note: Some rechargeable Cache Battery Packs are negatively affected by higher temperatures
and thus are prorated based on the amount of time that they spend at various ambient
temperatures.
Estimated time to warning (days)
Estimated time, in units of days, until a message is issued indicating that the replacement of the
rechargeable Cache Battery Pack should be scheduled.
Estimated time to error (days)
Estimated time, in units of days, until an error is reported indicating that the rechargeable Cache
Battery Pack must be replaced.

Chapter 4. PCI-X SCSI RAID Controller Maintenance 25

Forcing a Rechargeable Battery Error
This option allows you to force your PCI-X SCSI RAID Controller to put its Cache Battery Pack into an
error state. This state requires replacement of the battery. Typically, performing this task ensures that write
caching is stopped prior to replacing a Cache Battery Pack. Forcing the battery error can be performed
when you want to replace a Cache Battery Pack on one controller and you also want to replace other
Cache Battery Packs on controllers in the same system that have not yet issued the cache battery warning
nor cache battery error.

Forcing the battery error will result in the following:

v The system logs an error.
v Data caching becomes disabled on the selected controller.
v System performance could become significantly degraded until the Cache Battery Pack is replaced on
the selected controller.

Ensure that you have the correct type and quantity of Cache Battery Packs to do the replacement. To
resume normal operations, replace the Cache Battery Pack.

To force the battery error, do the following:

1. Navigate to the PCI-X SCSI Disk Array Manager by using the steps in Using the PCI-X SCSI Disk
Array Manager on page 13.
2. Select Diagnostics and Recovery Options.
3. Select Controller Rechargeable Battery Maintenance.
4. Select Force Controller Rechargeable Battery Error.
5. Select your PCI-X SCSI RAID Controller whose battery you want to replace.

Note: Using this option places the battery into the error state, which requires it to be replaced.
6. Press Enter.
7. Replace the Cache Battery Pack as described in Replacing the Rechargeable Cache Battery Pack.

Replacing the Rechargeable Cache Battery Pack

This section provides instructions for replacing the rechargeable Cache Battery Pack.

Note: When replacing the Cache Battery Pack, the battery must be disconnected for at least 15 seconds
before connecting the new battery. This is the minimum amount of time needed for the card to
recognize that the battery has been replaced.

CAUTION:
The battery is a nickel metal hydride battery. To avoid possible explosion, do not burn the battery.
Exchange it with the IBM approved part. Recycle or discard the battery as instructed by local
regulations. In the United States, IBM has a process for the collection of this battery. For
information, call 1-800-426-4333. Have the IBM part number for the battery unit available when you
call.

If the Cache Battery Pack is not already in the error state, follow the steps described in Forcing a
Rechargeable Battery Error before proceeding. After the battery is in the error state, replace it with a new
battery by taking the following steps:
1. Remove the adapter from the system by referring to your system documentation.
2. Use the following illustration to locate the casing A that holds the battery pack.
3. Squeeze the casing A to remove the battery unit from the card.
4. Remove the plug that connects the battery unit and the card.

26 PCI-X SCSI RAID Controller: Reference Guide for AIX

 Note: The plug fits in the board only one way so that it cannot be inserted incorrectly during the
replacement phase.
5. Remove the battery unit from the battery casing. Save the battery casing. The replacement battery
pack does not provide a casing.

Note: Ensure that the Cache Battery Pack is disconnected for at least 15 seconds before connecting
the new battery. This is the minimum amount of time needed for the card to recognize that the
battery has been replaced.
6. Install the new Cache Battery Pack by reversing this procedure.

A Battery Pack Casing

B Cache Directory Card

Replacing pdisks
Replace Failed pdisks as soon as possible, even if a reconstruction was initiated with a hot spare by the
controller. The Replace/Remove a Device Attached to an SCSI Hot Swap Enclosure Device option in
the SCSI and SCSI RAID Hot Plug Manager can be used to replace Failed pdisks. The PCI-X SCSI Disk
Array Manager provides a shortcut to the SCSI and SCSI RAID Hot Plug Manager. The SCSI and SCSI
RAID Hot Plug Manager allows you to perform the following tasks:
v List all SCSI hot swap slots and their contents
v Set the identify indication for a device attached to a SCSI hot swap enclosure device
v Add a device to a SCSI hot swap enclosure device
v Replace and remove a hot swap device
v Configure added and replaced devices

To start the SCSI and SCSI RAID Hot Plug Manager, do the following:
1. Navigate to the PCI-X SCSI Disk Array Manager by using the steps in Using the PCI-X SCSI Disk
Array Manager on page 13.
2. Select Diagnostics and Recovery Options.
3. Select SCSI and SCSI RAID Hot Plug Manager.

Chapter 4. PCI-X SCSI RAID Controller Maintenance 27

4. Select the action you want to take, and follow the instructions on the screen to complete the selected
operation.

Attention: Always use the SCSI and SCSI RAID Hot Plug Manager for devices attached to a PCI-X
SCSI RAID Controller. Do not use utilities intended for other RAID products, such as RAID Hot Plug
Devices.

Recovery Procedures for Disk Failures

The PCI-X SCSI RAID Controller handles disk failures differently, depending on the RAID level involved.
For a description of disk array states, pdisk states, and RAID levels, see Supported RAID Levels on
page 3. This section describes recovery procedures for each RAID level.

RAID Level 0
A single disk failure will cause a RAID level 0 array to change to the Failed state. After deleting the logical
volumes and file systems on the disk array and removing the disk array from the volume group, delete the
disk array, replace the Failed disk, then re-create the disk array. You must then add the disk array back to
a volume group, re-create the disk array logical volumes and file systems, and copy the data back to the
restored disk array from your backup media.

RAID Level 5
Single-Disk Failure
Whenever a single disk in a RAID level 5 disk array transitions to the Failed state, the disk array status
changes to Degraded. The disk array remains functional because the data on the Failed disk can be
reconstructed using parity and data on the remaining disks.

Whenever a disk is marked as Failed, replace it as soon as possible. If a hot spare disk was defined, the
controller may reconstruct the data on the disk automatically. If a hot spare reconstruct was not initiated by
the controller, replace the Failed disk and then initiate a reconstruct.

To initiate a reconstruct, do the following:

1. Navigate to the PCI-X SCSI Disk Array Manager by using the steps in Using the PCI-X SCSI Disk
Array Manager on page 13.
2. Select Reconstruct a PCI-X SCSI Disk Array.
3. Before you proceed, ensure that you have replaced the Failed disk.
4. Select the pdisk that you want to reconstruct.

Multiple-Disk Failures
If a second disk in a RAID level 5 disk array fails, the array will be marked as Failed and the data will not
be accessible. After deleting the logical volumes and file systems on the disk array and removing the disk
array from the volume group, delete the disk array, replace the Failed disks, then re-create the disk array.
You must then add the disk array back to a volume group, re-create the disk array logical volumes and file
systems, and copy the data back to the restored disk array from your backup media.

RAID Level 10
Single-Disk Failure
Whenever a single disk in a RAID level 10 disk array transitions to the Failed state, the disk array status
changes to Degraded. The disk array remains functional because the data on the Failed disk is also stored
on the other member of its mirrored pair.

28 PCI-X SCSI RAID Controller: Reference Guide for AIX

Whenever a disk is marked as Failed, replace it as soon as possible. If a hot spare disk was Defined, the
controller may reconstruct the data on the disk automatically. If a hot spare reconstruct was not initiated by
the controller, then initiate a reconstruct on the Failed disk following replacement.

To initiate a reconstruct, do the following:

1. Navigate to the PCI-X SCSI Disk Array Manager by using the steps in Using the PCI-X SCSI Disk
Array Manager on page 13.
2. Select Reconstruct a PCI-X SCSI Disk Array.
3. Before you proceed, ensure that you have replaced the Failed disk.
4. Select the Failed pdisk that you want to reconstruct.

Multiple-Disk Failures
If each Failed disk belongs to a different mirrored pair, then the array will be in the Degraded state
because the data on each Failed disk is still available from its mirrored pair. The recovery procedure for
this case is the same as the single-disk failure case. After you replace the Failed disks, initiate reconstruct
operations.

When both members of a mirrored pair fail, the disk array status changes to Failed. After deleting the
logical volumes and file systems on the disk array and removing the disk array from the volume group,
delete the disk array, replace the Failed disks, then re-create the disk array. You must then add the disk
array back to a volume group, re-create the disk array logical volumes and file systems, and copy the data
back to the restored disk array from your backup media.

Chapter 4. PCI-X SCSI RAID Controller Maintenance 29

30 PCI-X SCSI RAID Controller: Reference Guide for AIX
Chapter 5. Problem Determination and Recovery
Note: The procedures contained in this chapter are intended for service representatives specifically
trained on the system unit and subsystem that is being serviced. Additionally, some of the service
actions in this chapter might require involvement of the system administrator.

If a problem arises related to disk arrays and associated pdisks, use the following to identify the problem:
v Information presented by the Error Log Analysis (ELA)
v Hardware error logs viewed using the Display Hardware Error Report diagnostic task
v Disk array hdisk and pdisk status, viewed using the PCI-X SCSI Disk Array Manager

Error Log Analysis (ELA) analyzes errors presented by the adapter and recommends actions that need to
be performed to correct the errors. It is sometimes recommended that you perform a Maintenance Analysis
Procedure (MAP) to further determine what actions should be taken to resolve the problem. This chapter
provides many of these MAPs.

The MAPs contained in this chapter are intended to address only problems directly related to disk arrays
and SCSI bus-problem isolation. MAPs related to other device or adapter problems, when applicable, are
located in other system documentation.

Considerations
Read the following before using these problem determination and recovery procedures:
v If a disk array is being used as a boot device and the system fails to boot because of a suspected
disk-array problem, boot using the Standalone Diagnostic media. Error Log Analysis, AIX error logs, the
PCI-X SCSI Disk Array Manager, and other tools are available on the Standalone Diagnostics to help
determine and resolve the problem with the disk array.
v When invoking diagnostic routines for a PCI-X SCSI RAID Controller, it is recommended that Problem
Determination (PD) mode be used instead of System Verification (SV) mode unless there is a specific
reason to use SV mode (for example, you were directed to run SV mode by a MAP).
v After diagnostic routines for a PCI-X SCSI RAID Controller are run in SV mode, it is recommended to
run diagnostics in PD mode to ensure that new errors are analyzed. These actions should be performed
especially when using Standalone Diagnostic media.

Location Codes
Much of the location information contained in the hardware error logs is in the format of AIX location
codes.

The AIX location code format for a SCSI device is: AB-CD-EF-G,H where
v AB-CD identifies the PCI-X SCSI RAID Controller.
v EF identifies the Controllers SCSI bus that the device is attached to.

Note: For a disk array this value will be ff, which indicates a logical bus for RAID devices.
v G,H are the SCSI ID and logical unit number (LUN) of the device, respectively.

Often only a portion of the AIX location code is shown. For example:
v AB-CD identifies a PCI-X SCSI RAID Controller.
v AB-CD-EF identifies a PCI-X SCSI RAID Controllers SCSI bus.
v EF-G,H identifies the SCSI bus, SCSI ID, and LUN of an attached disk.

31
Identifying the Disk Array Problem
A disk array problem is uniquely identified by a Service Request Number (SRN). An SRN is in the format
nnnn - rrrr, where the first four digits of the SRN preceding the dash (-) is known as the Failing Function
Code (FFC, for example 2523) and the last four digits of the SRN following the dash (-) is known as the
reason code. The reason code indicates the specific problem that has occurred and must be obtained in
order to determine which MAP to use.

An SRN is provided by Error Log Analysis, which directs you to the MAPs contained in this chapter. To
obtain the reason code (last four digits of the SRN) from an AIX error log, see Finding an SRN Given an
AIX Error Log on page 64.

The SRN describes the problem that has been detected and should be considered the primary means of
identifying a problem. However, the List PCI-X SCSI Disk Array Configuration option within the PCI-X
SCSI Disk Array Manager is also useful in identifying a problem or confirming a problem described by
Error Log Analysis. For additional information about the PCI-X Disk Array Manager, see Using the PCI-X
SCSI Disk Array Manager on page 13.

Obtain the SRN and proceed to the next section to obtain a more detailed description of the problem and
to determine which MAP to use.

Service Request Number (SRN) Table

Using the SRN obtained from Error Log Analysis or from the AIX error log, use the following table to
determine which MAP to use. For MAPs, see Maintenance Analysis Procedures (MAPs) on page 34.

Note: The following table includes only SRNs that are associated with Maintenance Analysis Procedures
contained in this document. A complete list of SRNs can be found in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.
Table 1.
SRN Description MAP
nnnn - 8008 Permanent Cache Battery Pack failure MAP 3000
nnnn - 8009 Impending Cache Battery Pack failure MAP 3000
nnnn - 9000 Controller detected device error during configuration MAP 3090
nnnn - 9001 discovery
nnnn - 9002
nnnn - 9008 Controller does not support function expected for one or MAP 3030
more disks
nnnn - 9010 Cache data associated with attached disks cannot be found MAP 3020
nnnn - 9011 Cache data belongs to disks other than those attached MAP 3090
nnnn - 9020 Two or more disks are missing from a RAID-5 Disk Array MAP 3011
nnnn - 9021
nnnn - 9022
nnnn - 9023 One or more Disk Array members are not at required MAP 3012
physical locations
nnnn - 9024 Physical location of Disk Array members conflict with another MAP 3090
Disk Array
nnnn - 9025 Incompatible disk installed at degraded disk location in Disk MAP 3010
Array
nnnn - 9026 Previously degraded disk in Disk Array not found at required MAP 3090
physical location

32 PCI-X SCSI RAID Controller: Reference Guide for AIX

Table 1. (continued)
SRN Description MAP
nnnn - 9027 Disk Array is or would become degraded and parity data is MAP 3013
out of synchronization
nnnn - 9028 Maximum number of functional Disk Arrays has been MAP 3090
exceeded
nnnn - 9029 Maximum number of functional Disk Array disks has been MAP 3090
exceeded
nnnn - 9030 Disk Array is degraded due to missing/failed disk MAP 3010
nnnn - 9031 Automatic reconstruction initiated for Disk Array MAP 3010
nnnn - 9041 Background Disk Array parity checking detected and MAP 3090
corrected errors
nnnn - 9050 Required cache data can not be located for one or more MAP 3031
disks
nnnn - 9051 Cache data exists for one or more missing/failed disks MAP 3032
nnnn - 9052 Cache data exists for one or more modified disks MAP 3090
nnnn - 9054 RAID controller resources not available due to previous MAP 3021
problems
nnnn - 9060 One or more disk pairs are missing from a RAID-10 Disk MAP 3011
Array
nnnn - 9061 One or more disks are missing from a RAID-0 Disk Array MAP 3011
nnnn - 9062
nnnn - 9063 Maximum number of functional Disk Arrays has been MAP 3090
exceeded
nnnn - 9081 Controller detected device error during internal media MAP 3090
nnnn - 9082 recovery
nnnn - 9090 Disk has been modified after last known status MAP 3033
nnnn - 9091 Incorrect disk configuration change has been detected MAP 3033
nnnn - 9092 Disk requires Format before use MAP 3034
nnnn - 9200 Identify disk to be replaced MAP 3036
nnnn - FFF3 Disk media format bad MAP 3035
nnnn - 719 Various errors requiring SCSI bus problem isolation MAP 3050
nnnn - 720
nnnn - 721
nnnn - 3020
nnnn - 3100
nnnn - 3101
nnnn - 3109
nnnn - 3110
nnnn - FFFE
nnnn - 102E Various errors which call for disk replacement, however, MAP 3051
nnnn - 3002 replacing disk did not solve problem
nnnn - 3010
nnnn - 7001
nnnn - FFF4
nnnn - FFF6
nnnn - FFFA

Chapter 5. Problem Determination and Recovery 33

Maintenance Analysis Procedures (MAPs)
Use the following procedures to resolve adapter, cache, or disk array problems associated with a PCI-X
SCSI RAID Controller. See Service Request Number (SRN) Table on page 32 to identify which MAP to
use.

MAP 3000
Use this MAP to resolve the following problems:
v Permanent Cache Battery Pack failure (SRN nnnn - 8008)
v Impending Cache Battery Pack failure (SRN nnnn - 8009)

Step 3000-1
Are you here because of a permanent Cache Battery Pack failure (SRN nnnn - 8008)?

NO Go to Step 3000-2.
YES Go to Step 3000-3.

Step 3000-2
Prior to replacing the Cache Battery Pack, it must be forced into an error state. This will ensure that write
caching is stopped prior to replacing the battery pack thus preventing possible data loss. Perform the
following to force the Cache Battery Pack into an error state:

Note: Ensure that you have a replacement Cache Battery Pack before proceeding.
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Diagnostics and Recovery Options.
3. Select Controller Rechargeable Battery Maintenance.
4. Select Force Controller Rechargeable Battery Error.
5. Select the PCI-X SCSI RAID Controller.
6. Press Enter to continue and force the battery error.
7. Go to Step 3000-3.

Step 3000-3
Replace the Cache Battery Pack as follows:

Note: When replacing the Cache Battery Pack, the battery must be disconnected for at least 15 seconds
before connecting the new battery. This is the minimum amount of time needed for the card to
recognize that the battery has been replaced.

CAUTION:
The battery is a nickel metal hydride battery. To avoid possible explosion, do not burn. Exchange
only with the IBM approved part. Recycle or discard the battery as instructed by local regulations.
In the United States, IBM has a process for the collection of this battery. For information, call
1-800-426-4333. Have the IBM part number for the battery unit available when you call.

Attention: All cards are sensitive to electrostatic discharge.

1. Using appropriate service procedures, remove the adapter from the system.

34 PCI-X SCSI RAID Controller: Reference Guide for AIX

2. Locate the casing A that holds the battery pack in the following figure.

A Battery Pack Casing

B Cache Directory Card

3. Squeeze the casing A to remove the battery unit from the card.
4. Remove the plug that connects the battery unit and the card.

Note: The plug fits in the board only one way so that it cannot be inserted incorrectly during the
replacement phase.
5. Remove the battery unit from the battery casing. Save the battery casing. The replacement battery
pack does not provide a casing.

Note: Ensure that the Cache Battery Pack is disconnected for at least 15 seconds before connecting
the new battery. This is the minimum amount of time needed for the card to recognize that the
battery has been replaced.
6. Install the new Cache Battery Pack by reversing this procedure.
When the problem is resolved, then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3010
Use this MAP to resolve the following problems:
v Incompatible disk installed at degraded disk location in Disk Array (SRN nnnn - 9025)
v Disk Array is degraded due to missing/ failed disk (SRN nnnn - 9030)
v Automatic reconstruction initiated for Disk Array (SRN nnnn - 9031)

Step 3010-1
Identify the disk array by examining the hardware error log. The hardware error log may be viewed as
follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapters resources if the adapter resource is not known.

Chapter 5. Problem Determination and Recovery 35

5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem that sent
you here and select it.

Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.
6. Select the hardware error log to view. This error log displays the following disk array information under
the Array Information heading: Location, S/N(serial number), and RAID Level.
7. Go to Step 3010-2.

Step 3010-2
View the current disk array configuration as follows:
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select List PCI-X SCSI Disk Array Configuration.
3. Select the PCI-X SCSI RAID Controller identified in the hardware error log.
4. Go to Step 3010-3.

Step 3010-3
Does a disk array have a state of Degraded?

NO Go to Step 3010-4.
YES Go to Step 3010-5.

Step 3010-4
The affected disk array should have a state of either Rebuilding or Optimal due to the use of a hot spare
disk.

Identify the Failed disk, which is no longer a part of the disk array, by finding the pdisk listed at the bottom
of the screen that has a state of either Failed or RWProtected. Using appropriate service procedures, such
as use of the SCSI and SCSI RAID Hot Plug Manager, remove the failed disk and replace it with a new
disk to use as a hot spare:
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Diagnostics and Recovery Options .
3. Select SCSI and SCSI RAID Hot Plug Manager.
4. Select Identify a Device Attached to an SCSI Hot Swap Enclosure Device.
5. Choose the location for the device you want to remove or install.

Note: The visual indicator on the Device will blink at the Identify rate.
6. If you are removing a device:
a. Select Replace/Remove a Device Attached to an SCSI Hot Swap Enclosure Device.

Note: The visual indicator on the device will blink at the Remove rate.
b. Remove the device.

36 PCI-X SCSI RAID Controller: Reference Guide for AIX

 else, if installing a device:
a. Select Attach a Device to an SCSI Hot Swap Enclosure Device.

Note: The visual indicator on the device will blink at the Remove rate.
b. Insert the device.

If a new disk is not listed as a pdisk, it may first need to be prepared for use in a disk array. Do the
following:
1. Start the PCI-X SCSI Disk Array Manager
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Create an Array Candidate pdisk and Format to 522 Byte Sectors.
3. Select the PCI-X SCSI RAID Controller.
4. Select the disk(s) from the list that you want to prepare for use in the disk arrays.
In order to make the new disk usable as a hot spare, do the following:
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen .
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Change/Show PCI-X SCSI pdisk Status.
3. Select Create a Hot Spare.
4. Select the PCI-X SCSI RAID Controller.
5. Select the pdisk that you want to designate as a hot spare.

Note: Hot spare disks are useful only if their capacity is greater than or equal to that of the smallest
capacity disk in a disk array that becomes Degraded.

When the problem is resolved, go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

Step 3010-5
Identify the failed disk by finding the pdisk listed for the degraded disk array that has a state of Failed.
Using appropriate service procedures, such as use of the SCSI and SCSI RAID Hot Plug Manager,
remove the failed disk and replace it with a new disk to use in the disk array. The SCSI and SCSI RAID
Hot Plug Manager can be invoked as follows:
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Diagnostics and Recovery Options.
3. Select SCSI and SCSI RAID Hot Plug Manager.
4. Select Identify a Device Attached to an SCSI Hot Swap Enclosure Device.
5. Choose the location for the device you wish to remove/install.

Note: The visual indicator on the device will blink at the Identify rate.
6. If removing a device:
a. Select Replace/Remove a Device Attached to an SCSI Hot Swap Enclosure Device.

Chapter 5. Problem Determination and Recovery 37

 Note: The visual indicator on the device will blink at the Remove rate.
b. Remove the device.

else, if installing a device:

a. Select Attach a Device to an SCSI Hot Swap Enclosure Device.

Note: The visual indicator on the device will blink at the Remove rate.
b. Insert the device.
To bring the disk array back to a state of Optimal, do the following:
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Reconstruct a PCI-X SCSI Disk Array.
3. Select the failed pdisk to reconstruct.

Note: The replacement disk should have a capacity that is greater than or equal to that of the smallest
capacity disk in the degraded disk array.

When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3011
Use this MAP to resolve the following problems:
v Two or more disks are missing from a RAID-5 Disk Array (SRN nnnn - 9020 / nnnn - 9021 / nnnn -
9022)
v One or more disk pairs are missing from a RAID-10 Disk Array (SRN nnnn - 9060)
v One or more disks are missing from a RAID-0 Disk Array (SRN nnnn - 9061 / nnnn - 9062)

Step 3011-1
Identify the disks missing from the disk array by examining the hardware error log. The hardware error log
may be viewed as follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapters resources if the adapter resource is not known.
5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem which sent
you here and select it.

Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.
6. Select the hardware error log to view. Viewing the hardware error log, the missing disks are those
listed under Array Member Information with an Actual Location of *unkwn*.
7. Go to Step 3011-2.

Step 3011-2
There are three possible ways to correct the problem. Perform only one of the following three options,
listed in the order of preference:

38 PCI-X SCSI RAID Controller: Reference Guide for AIX

v Locate the missing disks and install them in the correct physical locations (that is the Expected
Locations) in the system. Perform only one of the following two options:
IPL the system or logical partition
Unconfigure and reconfigure the adapter by performing the following:
1. Unconfigure the adapter.
a. Start the PCI-X SCSI Disk Array Manager.
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Unconfigure an Available PCI-X SCSI RAID Controller.
2. Configure the adapter.
a. Start the PCI-X SCSI Disk Array Manager
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Configure a Defined PCI-X SCSI RAID Controller.
When the problem is resolved then go to MAP 0410: Repair Checkout, inRS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.
v Delete the disk array, as follows:
Attention: All data on the disk array will be lost.
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Delete a PCI-X SCSI Disk Array.
3. Select the PCI-X SCSI RAID Controller.
4. Select the disk array to delete.
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.
v Format the remaining members of the disk array, as follows
Attention: All data on the disk array will be lost.
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Diagnostics and Recovery Options.
3. Select Format Physical Disk Media (pdisk).
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

Chapter 5. Problem Determination and Recovery 39

MAP 3012
Use this MAP to resolve the following problem:
One or more Disk Array Members are not at required physical locations (SRN nnnn - 9023)

Step 3012-1
Identify the disks which are not at their required physical locations by examining the hardware error log.
The hardware error log may be viewed as follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapters resources if the adapter resource is not known.
5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem which sent
you here and select it.

Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.
6. Select the hardware error log to view.
Viewing the hardware error log, the disks which are not at their required locations are those listed
under Array Member Information with an Expected Location and Actual Location which do not match.

Note: An Actual Location of *unkwn* is acceptable, and no action is needed to correct it. This *unkwn*
location should only occur for the disk array member that corresponds to the Degraded Disk
S/N.
7. Go to Step 3012-2.

Step 3012-2
There are three possible ways to correct the problem. Perform only one of the following three options,
listed in the order of preference:
v Locate the missing disks and install them in the correct physical locations (that is the Expected
Locations) in the system. Perform only one of the following two options:
IPL the system or logical partition
Unconfigure and reconfigure the adapter by performing the following:
1. Unconfigure the adapter.
a. Start the PCI-X SCSI Disk Array Manager.
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Unconfigure an Available PCI-X SCSI RAID Controller.
2. Configure the adapter.
a. Start the PCI-X SCSI Disk Array Manager
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Configure a Defined PCI-X SCSI RAID Controller.

40 PCI-X SCSI RAID Controller: Reference Guide for AIX

 When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.
v Delete the disk array, as follows:
Attention: All data on the disk array will be lost.
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Delete a PCI-X SCSI Disk Array.
3. Select the PCI-X SCSI RAID Controller.
4. Select the disk array to delete.
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.
v Format the remaining members of the disk array, as follows
Attention: All data on the disk array will be lost.
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Diagnostics and Recovery Options.
3. Select Format Physical Disk Media (pdisk).
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3013
Use this MAP to resolve the following problem:
Disk array is or would become degraded and parity data is out of synchronization (SRN nnnn - 9027)

Step 3013-1
Identify the adapter and disks by examining the hardware error log. The hardware error log may be viewed
as follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapters resources if the adapter resource is not known.
5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem which sent
you here and select it.

Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.
6. Select the hardware error log to view. Viewing the hardware error log, if the disk array member which
corresponds to the Degraded Disk S/N has an Actual Location of *unkwn* and is not physically
present, it may be helpful to find this disk.
7. Go to Step 3013-2.

Chapter 5. Problem Determination and Recovery 41

Step 3013-2
Have the adapter card or disks been physically moved recently?

NO Contact your service support organization.

YES Go to Step 3013-3.

Step 3013-3
There are three possible ways to correct the problem. Perform only one of the following three options,
listed in the order of preference:
v Restore the adapter and disks back to their original configuration. Perform onlyone of the following two
options:
IPL the system or logical partition
Unconfigure and reconfigure the adapter by performing the following:
1. Unconfigure the adapter.
a. Start the PCI-X SCSI Disk Array Manager.
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Unconfigure an Available PCI-X SCSI RAID Controller.
2. Configure the adapter.
a. Start the PCI-X SCSI Disk Array Manager
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Configure a Defined PCI-X SCSI RAID Controller.
When the problem is resolved then go to MAP 0410: Repair Checkout, inRS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.
v Delete the disk array, as follows:
Attention: All data on the disk array will be lost.
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Delete a PCI-X SCSI Disk Array.
3. Select the PCI-X SCSI RAID Controller.
4. Select the disk array to delete.
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.
v Format the remaining members of the disk array, as follows
Attention: All data on the disk array will be lost.
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.

42 PCI-X SCSI RAID Controller: Reference Guide for AIX

 2. Select Diagnostics and Recovery Options.
3. Select Format Physical Disk Media (pdisk).
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3020
Use this MAP to resolve the following problem:
Cache data associated with attached disks cannot be found (SRN nnnn - 9010)

Step 3020-1
Did you just exchange the adapter as the result of a failure?

NO Go to Step 3020-3.
YES Go to Step 3020-2.

Step 3020-2
1. Reclaim Controller Cache Storage as follows:
Attention: Data will be lost.
This may be performed as follows:
a. Start the PCI-X SCSI Disk Array Manager.
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Reclaim Controller Cache Storage.
d. Select the PCI-X SCSI RAID Controller.
e. Confirm that you wish to proceed.

Note: On the Reclaim Controller Cache Storage results screen, the number of lost sectors is
displayed. If the number is 0, there is no data loss. If the number is not 0, data has been lost
and the system operator may want to restore data after this procedure is completed.
2. Using appropriate service procedures, remove the new adapter, reinstall the Cache Directory Card
(label B in the following illustration) that came with the new adapter, and reinstall the new adapter. The

Chapter 5. Problem Determination and Recovery 43

 original Cache Directory Card from the failed adapter should be kept with the failed adapter.

A Battery Pack Casing

B Cache Directory Card

When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

Step 3020-3
Has the Cache Directory Card B been physically moved recently?

NO Go to Step 3020-5.
YES Go to Step 3020-4.

Step 3020-4
Restore Cache Directory Cards or adapters back to their original configuration.

When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

Step 3020-5
If the system has been powered off for several days after an abnormal power-down, the Cache Battery
Pack may be depleted. Do not replace the adapter or the Cache Battery Pack. Reclaim the controller
cache storage as follows:

Attention: Data will be lost.

1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Diagnostics and Recovery Options.
3. Select Reclaim Controller Cache Storage.
4. Select the PCI-X SCSI RAID Controller.

44 PCI-X SCSI RAID Controller: Reference Guide for AIX

5. Confirm that you wish to proceed

Note: On the Reclaim Controller Cache Storage results screen, the number of lost sectors is
displayed. If the number is 0, there is no data loss. If the number is not 0, data has been lost
and the system operator may want to restore data after this procedure is completed.
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3021
Use this MAP to resolve the following problem:
RAID controller resources not available due to previous problems (SRN nnnn - 9054)

Step 3021-1
Perform the following:
1. Remove any new or replacement disks which have been attached to the adapter.
2. Take action on the other errors which have occurred at the same time as this error.
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3030
Use this MAP to resolve the following problem:
Controller does not support function expected by one or more disks (SRN nnnn - 9008)

Step 3030-1
Identify the affected disks by examining the hardware error log. The hardware error log may be viewed as
follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapters resources if the adapter resource is not known.
5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem which sent
you here and select it.

Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.
6. Select the hardware error log to view. Viewing the hardware error log, the Device Errors Detected field
indicates the total number of disks which are affected. The Device Errors Logged field indicates the
number of disks for which detailed information is provided. Under the Device heading, the Location,
Vendor/Product ID, and S/N are provided for up to three disks. Additionally, the Controller Type and
S/N for each of these disks indicates the adapter to which the disk was last attached when it was
operational.
7. Go to Step 3030-2.

Step 3030-2
Have the adapter card or disks been physically moved recently?

NO Contact your service support organization.

YES Go to Step 3030-3.

Chapter 5. Problem Determination and Recovery 45

Step 3030-3
There are two possible ways to correct the problem. Perform only one of the following two options, listed
in the order of preference:
v Restore the adapter and disks back to their original configuration. Perform onlyone of the following two
options:
IPL the system or logical partition
Unconfigure and reconfigure the adapter by performing the following:
1. Unconfigure the adapter.
a. Start the PCI-X SCSI Disk Array Manager.
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Unconfigure an Available PCI-X SCSI RAID Controller.
2. Configure the adapter.
a. Start the PCI-X SCSI Disk Array Manager
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Configure a Defined PCI-X SCSI RAID Controller.
When the problem is resolved then go to MAP 0410: Repair Checkout, inRS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.
v Format the disks, as follows:
Attention: All data on the disk array will be lost.
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Diagnostics and Recovery Options.
3. Select Format Physical Disk Media (pdisk).
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3031
Use this MAP to resolve the following problem:
Required cache data cannot be located for one or more disks (SRN nnnn - 9050)

Step 3031-1
Did you just exchange the adapter as the result of a failure?

NO Go to Step 3031-3.
YES Go to Step 3031-2.

Step 3031-2
Note: The failed adapter that you have just exchanged contains cache data that is required by the disks
that were attached to that adapter. If the adapter that you just exchanged is failing intermittently,
46 PCI-X SCSI RAID Controller: Reference Guide for AIX
 reinstalling it and IPLing the system may allow the data to be successfully written to the disks. After
the cache data is written to the disks and the system is powered off normally, the adapter can be
replaced without data being lost. Otherwise, continue with this procedure.

When continuing with the new adapter, perform the following:

1. Using appropriate service procedures, remove the new adapter, replace the Cache Directory Card B
shown in the following figure with the original Cache Directory Card from the failed adapter, and
reinstall the new adapter.

A Battery Pack Casing

B Cache Directory Card

2. An error with SRN nnnn - 9010 will occur. Ignore this error and continue with the next steps.
3. Reclaim Controller Cache Storage as follows.
Attention: Data will be lost.
a. Start the PCI-X SCSI Disk Array Manager.
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Reclaim Controller Cache Storage.
d. Select the PCI-X SCSI RAID Controller.
e. Confirm that you wish to proceed.

Note: On the Reclaim Controller Cache Storage results screen, the number of lost sectors is
displayed. If the number is 0, there is no data loss. If the number is not 0, data has been lost
and the system operator may want to restore data after this procedure is completed.
4. Using appropriate service procedures, remove the new adapter, reinstall the Cache Directory Card
(label B in the following illustration) that came with the new adapter, and reinstall the new adapter. The

Chapter 5. Problem Determination and Recovery 47

 original Cache Directory Card from the failed adapter should be kept with the failed adapter.

A Battery Pack Casing

B Cache Directory Card

When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems

Step 3031-3
Identify the affected disks by examining the hardware error log. The hardware error log may be viewed as
follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapters resources if the adapter resource is not known.
5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem which sent
you here and select it.

Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.
6. Select the hardware error log to view. Viewing the hardware error log, the Device Errors Detected field
indicates the total number of disks which are affected. The Device Errors Logged field indicates the
number of disks for which detailed information is provided. Under the Device heading, the Location,
Vendor/Product ID, and S/N are provided for up to three disks. Additionally, the Controller Type and
S/N for each of these disks indicates the adapter to which the disk was last attached when it was
operational.
7. Go to Step 3031-4.

Step 3031-4
Have the adapter card or disks been physically moved recently?

NO Contact your service support organization.

48 PCI-X SCSI RAID Controller: Reference Guide for AIX

YES Go to Step 3031-5.

Step 3031-5
Is the data on the disks needed for this or any other system?

NO Go to Step 3031-7.
YES Go to Step 3031-6.

Step 3031-6
The adapter and disks, identified above, must be reunited so that the cache data can be written to the
disks.

Restore the adapter and disks back to their original configuration.

Once the cache data is written to the disks and the system is powered off normally, the adapter and/or
disks may be moved to another location.

When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

Step 3031-7
There are three possible ways to correct the problem. Perform only one of the following three options,
listed in the order of preference:
v Reclaim Controller Cache Storage by performing the following:
Attention: All data on the disk array will be lost.
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Diagnostics and Recovery Options.
3. Select Reclaim Controller Cache Storage.
4. Select the PCI-X SCSI RAID Controller.
5. Confirm that you will Allow Unknown Data Loss.
6. Confirm that you wish to proceed.
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.
v If the disks are members of a disk array, delete the disk array.
Attention: All data on the disk array will be lost.
This may be performed as follows:
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Delete a PCI-X SCSI Disk Array.
3. Select the PCI-X SCSI RAID Controller.
4. Select the disk array to delete.
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

Chapter 5. Problem Determination and Recovery 49

v Format the disks, as follows:
Attention: All data on the disks will be lost.
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Diagnostics and Recovery Options.
3. Select Format Physical Disk Media (pdisk).
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3032
Use this MAP to resolve the following problem:
Cache data exists for one or more missing or failed disks (SRN nnnn - 9051)

The possible causes are:

v One or more disks have failed on the adapter.
v One or more disks were either moved concurrently or were removed after an abnormal power off.
v The adapter was moved from a different system or a different location on this system after an abnormal
power off.
v The cache of the adapter was not cleared before it was shipped to the customer.

Step 3032-1
Identify the affected disks by examining the hardware error log. The hardware error log may be viewed as
follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapters resources if the adapter resource is not known.
5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem which sent
you here and select it.

Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.
6. Select the hardware error log to view. Viewing the hardware error log, the Device Errors Detected field
indicates the total number of disks which are affected. The Device Errors Logged field indicates the
number of disks for which detailed information is provided. Under the Device heading, the Location,
Vendor/Product ID, and S/N are provided for up to three disks. Additionally, the Controller Type and
S/N for each of these disks indicates the adapter to which the disk was last attached when it was
operational.
7. Go to Step 3030-2.

Step 3032-2
Are there other disk or adapter errors which have occurred at about the same time as this error?

NO Go to Step 3032-3.
YES Go to Step 3032-6.

50 PCI-X SCSI RAID Controller: Reference Guide for AIX

Step 3032-3
Is the data on the disks (and thus the cache data for the disks) needed for this or any other system?

NO Go to Step 3032-7.
YES Go to Step 3032-4.

Step 3032-4
Have the adapter card or disks been physically moved recently?

NO Contact your service support organization.

YES Go to Step 3032-5.

Step 3032-5
The adapter and disks must be reunited so that the cache data can be written to the disks.

Restore the adapter and disks back to their original configuration.

After the cache data is written to the disks and the system is powered off normally, the adapter and/or
disks may be moved to another location.

When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

Step 3032-6
Take action on the other errors that have occurred at the same time as this error.

When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

Step 3032-7
Attention: Data will be lost.

Reclaim the Controller Cache Storage by performing the following:

1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Diagnostics and Recovery Options.
3. Select Reclaim Controller Cache Storage.
4. Select the PCI-X SCSI RAID Controller.
5. Confirm that you will Allow Unknown Data Loss.
6. Confirm that you wish to proceed.

When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3033
Use this MAP to resolve the following problems:
v Disk has been modified after last known status (SRN nnnn - 9090)
v Incorrect disk configuration change has been detected (SRN nnnn - 9091)

Chapter 5. Problem Determination and Recovery 51

Step 3033-1
Perform onlyone of the following two options:
v IPL the system or logical partition
v Unconfigure and reconfigure the adapter by performing the following:
1. Unconfigure the adapter.
a. Start the PCI-X SCSI Disk Array Manager.
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Unconfigure an Available PCI-X SCSI RAID Controller.
2. Configure the adapter.
a. Start the PCI-X SCSI Disk Array Manager
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Configure a Defined PCI-X SCSI RAID Controller.

Take action on the other errors which have occurred at the same time as this error.

When the problem is resolved then go to MAP 0410: Repair Checkout, inRS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3034
Use this MAP to resolve the following problem:
Disk requires Format before use (SRN nnnn - 9092)

The possible causes are:

v Disk is a previously failed disk from a disk array and was automatically replaced by a hot spare disk.
v Disk is a previously failed disk from a disk array and was removed and later reinstalled on a different
adapter or different location on this adapter.
v Appropriate service procedures were not followed when replacing disks or reconfiguring the adapter,
such as not using the SCSI and SCSI RAID Hot Plug Manager when concurrently removing/installing
disks or not performing a normal power down of the system prior to reconfiguring disks and adapters.
v Disk is member of a disk array, but was detected subsequent to the adapter being configured.
v Disk has multiple or complex configuration problems.

Step 3034-1
Identify the affected disks by examining the hardware error log. The hardware error log may be viewed as
follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapters resources if the adapter resource is not known.
5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem which sent
you here and select it.

52 PCI-X SCSI RAID Controller: Reference Guide for AIX

 Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.
6. Select the hardware error log to view. Viewing the hardware error log, the Device Errors Detected field
indicates the total number of disks which are affected. The Device Errors Logged field indicates the
number of disks for which detailed information is provided. Under the Device heading, the Location,
Vendor/Product ID, and S/N are provided for up to three disks. Additionally, the Controller Type and
S/N for each of these disks indicates the adapter to which the disk was last attached when it was
operational.
7. Go to Step 3030-2.

Step 3034-2
Are there other disk or adapter errors which have occurred at about the same time as this error?

NO Go to Step 3034-3.
YES Go to Step 3034-5.

Step 3034-3
Have the adapter card or disks been physically moved recently?

NO Go to Step 3034-4.
YES Go to Step 3034-6.

Step 3034-4
Is the data on the disks not needed for this or any other system and you wish to continue to use them with
this adapter?

NO Go to Step 3034-6.
YES Go to Step 3034-7.

Step 3034-5
Take action on the other errors which have occurred at the same time as this error.

When the problem is resolved then go to MAP 0410: Repair Checkout, inRS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

Step 3034-6
Perform only one of the following actions that is most applicable to your situation:
v Perform only one of the following two options:
IPL the system or logical partition
Unconfigure and reconfigure the adapter by performing the following:
1. Unconfigure the adapter.
a. Start the PCI-X SCSI Disk Array Manager.
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Unconfigure an Available PCI-X SCSI RAID Controller.
2. Configure the adapter.
a. Start the PCI-X SCSI Disk Array Manager

Chapter 5. Problem Determination and Recovery 53

 1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Configure a Defined PCI-X SCSI RAID Controller.

Take action on the other errors which have occurred at the same time as this error.

When the problem is resolved then go to MAP 0410: Repair Checkout, inRS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.
v Restore the adapter and disks to their original configuration. Once this has been done, perform onlyone
of the following two options:
IPL the system or logical partition
Unconfigure and reconfigure the adapter by performing the following:
1. Unconfigure the adapter.
a. Start the PCI-X SCSI Disk Array Manager.
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Unconfigure an Available PCI-X SCSI RAID Controller.
2. Configure the adapter.
a. Start the PCI-X SCSI Disk Array Manager
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Configure a Defined PCI-X SCSI RAID Controller.
When the problem is resolved then go to MAP 0410: Repair Checkout, inRS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.
v Remove the disks from this adapter.
When the problem is resolved then go to MAP 0410: Repair Checkout, inRS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

Step 3034-7
There are two possible ways to correct the problem. Perform only one of these options.
v Format the disks.
Attention: All data on the disks will be lost.
This may be performed as follows:
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Diagnostics and Recovery Options.
3. Select Format Physical Disk Media (pdisk).
When the problem is resolved then go to MAP 0410: Repair Checkout, inRS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

54 PCI-X SCSI RAID Controller: Reference Guide for AIX

v If the disks are members of a disk array, delete the disk array by doing the following.
Attention: All data on the disk array will be lost.

Note: In some rare scenarios, deleting the disk array will not have no effect on a disk and the disk
must be formatted instead.
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Delete a PCI-X SCSI Disk Array.
3. Select the PCI-X SCSI RAID Controller.
4. Select the disk array to delete.

When the problem is resolved then go to MAP 0410: Repair Checkout, inRS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3035
Use this MAP to resolve the following problem:
Disk media format bad (SRN nnnn - FFF3)

The possible causes are:

v Disk was being formatted and was powered off during this process.
v Disk was being formatted and was reset during this process.

Step 3035-1
Identify the affected disk by examining the hardware error log. The hardware error log may be viewed as
follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapter resources if the adapter resource is not known.
5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem which sent
you here and select it.

Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.
6. Select the hardware error log to view. Viewing the hardware error log, under the Disk Information
heading, the Location, Vendor/Product ID, and S/N are provided for the disk.
7. Go to Step 3035-2.

Step 3035-2
Format the disk by performing the following.

Attention: All data on the disks will be lost.

1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.

Chapter 5. Problem Determination and Recovery 55

2. Select Diagnostics and Recovery Options.
3. Select Format Physical Disk Media (pdisk).

When the problem is resolved then go to MAP 0410: Repair Checkout, inRS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3036
Use this MAP to resolve the following problem:
Identify disk to be replaced (SRN nnnn - 9200)

You are sent here when a pdisk (that is physical disk in 522 bytes/sector format) is to be replaced,
however, the location of this disk was not provided.

Step 3036-1
Identify the failing disk by examining the hardware error log. The hardware error log may be viewed as
follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapters resources if the adapter resource is not known.
5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem which sent
you here and select it.

Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.
6. Select the hardware error log to view. Viewing the hardware error log, under the Disk Information
heading, the Location, Vendor/Product ID, and S/N are provided for the disk.
7. Go to Step 3036-2.

Step 3036-2
Using appropriate service procedures, such as use of the SCSI and SCSI RAID Hot Plug Manager,
remove the failed disk and replace it with a new disk. The SCSI and SCSI RAID Hot Plug Manager can be
invoked as follows:
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select Diagnostics and Recovery Options.
3. Select SCSI and SCSI RAID Hot Plug Manager.
4. Select Identify a Device Attached to an SCSI Hot Swap Enclosure Device.
5. Choose the location for the device you wish to remove or install

Note: The visual indicator on the Device will blink at the Identify rate.
6. If removing a device:
a. Select Replace/Remove a Device Attached to an SCSI Hot Swap Enclosure Device

Note: The visual indicator on the Device will blink at the Remove rate.
b. Remove the device

56 PCI-X SCSI RAID Controller: Reference Guide for AIX

 else if installing a device:
a. Select Attach a Device to an SCSI Hot Swap Enclosure Device

Note: The visual indicator on the Device will blink at the Remove rate.
b. Insert the device
7. Go to Step 3036-3.

Step 3036-3
1. Run diagnostics in system verification mode on the adapter
2. Take action on any other errors which may have surfaced due to removing the disk, if any, such as for
degraded disk arrays
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3050
Use the following to perform SCSI bus problem isolation.

Considerations:
v Remove power from the system before connecting and disconnecting cables or devices, as appropriate,
to prevent hardware damage or erroneous diagnostic results.
v Some systems have SCSI and PCI-X bus interface logic integrated onto the system boards and use a
pluggable RAID Enablement Card (a non-PCI form factor card) for these SCSI/PCI-X buses. An
example of such a RAID Enablement Card is FC 5709. For these configurations, replacement of the
RAID Enablement Card is unlikely to solve a SCSI bus-related problem because the SCSI bus interface
logic is on the system board.
v Some adapters provide two connectors, one internal and one external, for each SCSI bus. For this type
of adapter, it is not acceptable to use both connectors for the same SCSI bus at the same time. SCSI
bus problems are likely to occur if this is done. However, it is acceptable to use an internal connector
for one SCSI bus and an external connector for another SCSI bus. The internal and external connectors
are labeled to indicate which SCSI bus they correspond to.

Attention: Replacing RAID adapters is not recommended without assistance from your service support
organization when SCSI bus problems exist. Because the adapter may contain non-volatile write cache
data and configuration data for the attached disk arrays, additional problems can be created by replacing a
adapter when SCSI bus problems exist.

Attention: Removing functioning disks in a disk array is not recommended without assistance from your
service support organization. A disk array may become degraded or failed if functioning disks are removed
and additional problems may be created.

Common Device Removal and Installation Procedure

When this MAP calls for a device (that is disk, tape, CD-ROM, or DVD-ROM) to be removed or installed,
use this common device removal and installation procedure:

If the boot device is not on this adapter and the device to be removed or installed is a hot-swap device,
follow this procedure. If these conditions do not apply to your situation, see the else section located at the
end of this procedure.
1. Remove or install the device by invoking the SCSI and SCSI RAID Hot Plug Manager.
a. Start the PCI-X Disk Array Manager.
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.

Chapter 5. Problem Determination and Recovery 57

 b. Select Diagnostics and Recovery Options.
c. Select SCSI and SCSI RAID Hot Plug Manager.
d. Select Identify a Device Attached to an SCSI Hot Swap Enclosure Device.
e. Choose the location for the device you wish to remove or install.

Note: The visual indicator on the device will blink at the Identify rate.
f. If removing a device:
1) Select Replace/Remove a Device Attached to an SCSI Hot Swap Enclosure Device.

Note: The visual indicator on the device will blink at the Remove rate.
2) Remove the device.
3) Label the device with the slot it was removed from to ensure it can be reinstalled in the same
location.
else if installing a device:
1) Select Attach a Device to an SCSI Hot Swap Enclosure Device.

Note: The visual indicator on the device will blink at the Remove rate.
2) Insert the device.
2. Unconfigure the adapter
a. Start the PCI-X SCSI Disk Array Manager.
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Unconfigure an Available PCI-X SCSI RAID Controller.
3. Configure the adapter.
a. Start the PCI-X SCSI Disk Array Manager.
1) Start Diagnostics and select Task Selection on the Function Selection screen.
2) Select RAID Array Manager.
3) Select PCI-X SCSI Disk Array Manager.
b. Select Diagnostics and Recovery Options.
c. Select Configure a Defined PCI-X SCSI RAID Controller.
else:
1. Power off the system/logical partition
2. Remove/install the device(s)
3. Power on the system/logical partition

Step 3050-1
Identify the SCSI bus which the problem is occurring on by examining the hardware error log. The
hardware error log may be viewed as follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapter resources if the adapter resource is not known.
5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem which sent
you here and select it.

58 PCI-X SCSI RAID Controller: Reference Guide for AIX

 Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.
6. Select the hardware error log to view. Viewing the hardware error log, under the Disk Information
heading, the Location field can be used to identify which SCSI bus the error is associated with (that is
the SCSI bus is the value EF given a location of EF-G,H).
7. Go to Step 3050-2.

Step 3050-2
Have recent changes been made to the SCSI configuration?

NO Go to Step 3050-5.
YES Go to Step 3050-3.

Step 3050-3
Check for the following problems:
v Address conflicts between devices
v Cabling problems such as; configurations that exceed the maximum cable lengths, missing termination,
or excessive termination
v Both internal and external connectors for this SCSI bus are being used at the same time (only one
should have a cable attached)
v Ensure the SCSI bus does not have multi-initiators (for example, set up for a high-availability
configuration).

Note: Multi-initiator and High Availability (for example, HACMP) support is not provided at this time.
For more details about supported SCSI cabling, refer to RS/6000 Eserver pSeries Adapters, Devices,
and Cable Information for Multiple Bus Systems.

Did you find a problem?

NO Go to Step 3050-5.
YES Go to Step 3050-4.

Step 3050-4
1. Power off the system or logical partition.
2. Correct the problem.
3. Power on the system or logical partition, and run diagnostics in system verification mode on the
adapter.
Did a SCSI bus-related failure occur?

NO Go to Step 3050-16.
YES Go to Step 3050-5.

Step 3050-5
Is problem related to the thermal fuse (that is SRN nnnn-719)?

NO Go to Step 3050-7.
YES Go to Step 3050-6.

Chapter 5. Problem Determination and Recovery 59

Step 3050-6
The thermal fuse protects the SCSI bus from high currents due to shorts on the terminator, cable, or
device. It is unlikely that the thermal fuse can be tripped by a defective adapter. A fault (short-circuit)
causes an increase in resistance and temperature of the thermal fuse. The increase in temperature causes
the thermal fuse to halt current flow. The thermal fuse returns to a low resistive and low temperature state
when the fault is removed from the SCSI bus or when the system is turned off. Wait 10 seconds for the
thermal fuse to reset itself and recover, then retest.

If the same error persists, replace the components of the failing SCSI bus in the following order. Wait 10
seconds for the thermal fuse to reset itself between steps.
1. Cable (if present)
2. DASD backplane (if present)
3. System board (if SCSI bus interface logic is on the system board)

To replace a component and verify that the problem was corrected, do the following:
1. Power off the system or logical partition.
2. Replace a component listed above.
3. Power on the system or logical partition, and run diagnostics in system verification mode on the
adapter.
Did you correct the problem?

NO Go to Step 3050-7.
YES Go to Step 3050-16.

Step 3050-7
Determine if any of the disk arrays on the adapter are in a Degraded state as follows:
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select List PCI-X SCSI Disk Array Configuration.
3. Select the PCI-X SCSI RAID Controller identified in the hardware error log.
Does any disk array have a State of Degraded?

NO Go to Step 3050-9.
YES Go to Step 3050-8.

Step 3050-8
1. Identify the failed disk(s) by first finding disk arrays with a state of Degraded and then a pdisk for that
disk array which has a state of Failed.
2. Remove the failed disk from each degraded disk array by using the Common Device Removal and
Installation Procedure on page 57.
3. Run diagnostics in system verification mode on the adapter.
Did a SCSI bus related failure occur?

NO Go to Step 3050-16.
YES Go to Step 3050-9.

60 PCI-X SCSI RAID Controller: Reference Guide for AIX

Step 3050-9
Are there any non-essential removable media devices (for example tape, CD-ROM, or DVD-ROM) on the
SCSI bus?

NO Go to Step 3050-12.
YES Go to Step 3050-10.

Step 3050-10
1. Remove one of the non-essential removable media devices by using the Common Device Removal
and Installation Procedure on page 57.
2. Run diagnostics in system verification mode on the adapter.
Did a SCSI bus related failure occur?

NO Go to Step 3050-11.
YES Go to Step 3050-9.

Step 3050-11
The last removable media device removed from the SCSI bus may be the cause of the SCSI bus
problems. Follow the repair procedures for that device.

Go to Step 3050-16.

Step 3050-12
Are there any non-essential disks which are not disk array members (for example, 512 byte/sector
standalone disks, hot spare disks, or Array Candidates) on the SCSI bus?

NO Go to Step 3050-15.
YES Go to Step 3050-13.

Step 3050-13
1. Remove one of the non-essential disks devices by using the Common Device Removal and
Installation Procedure on page 57.
2. Run diagnostics in system verification mode on the adapter.
Did a SCSI bus related failure occur?

NO Go to Step 3050-14.
YES Go to Step 3050-12.

Step 3050-14
The last disk removed from the SCSI bus may be the cause of the SCSI bus problems. Follow the repair
procedures for that device.

Go to Step 3050-16.

Step 3050-15
Contact your service support organization.

Exit this procedure

Step 3050-16
1. Reinstall any good devices that were removed by using the Common Device Removal and Installation
Procedure on page 57.

Chapter 5. Problem Determination and Recovery 61

2. Run diagnostics in system verification mode on the adapter.
3. Perform the appropriate problem determination steps to resolve any other non-SCSI bus related errors
that appear, if any, such as for degraded disk arrays.
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3051
Use the following to determine what other FRUs, besides a disk, may need to be replaced in order to
solve a problem.

You are sent here when a pdisk (that is physical disk in 522 bytes/sector format) was identified as the
primary FRU to replace in order to solve a problem. However, if replacing the disk did not resolve the
problem then other FRUs may need to be replaced.

Considerations:
v Remove power from the system before connecting and disconnecting cables or devices, as appropriate,
to prevent hardware damage or erroneous diagnostic results.
v Keep in mind that some systems have SCSI and PCI-X bus interface logic integrated onto the system
boards and use a pluggable RAID Enablement Card (a non-PCI form factor card) for these SCSI/PCI-X
busses. An example of such a RAID Enablement Card is FC 5709. For these configurations,
replacement of the RAID Enablement Card is unlikely to solve a SCSI bus related problem since the
SCSI bus interface logic is on the system board.
v Some adapters provide two connectors, one internal and one external, for each SCSI bus. For this type
of adapter, it is not acceptable to use both connectors for the same SCSI bus at the same time. SCSI
bus problems are likely to occur if this is done. However, it is acceptable to use an internal connector
for one SCSI bus and an external connector for another SCSI bus. The internal and external connectors
are labeled to indicate which SCSI bus they correspond to.

Attention: Replacing RAID adapters is not recommended without assistance from your service support
organization when SCSI bus problems exist. Because the adapter may contain non-volatile write cache
data and configuration data for the attached disk arrays, additional problems can be created by replacing a
adapter when SCSI bus problems exist.

Attention: Removing functioning disks in a disk array is not recommended without assistance from your
service support organization. A disk array may become degraded or failed if functioning disks are removed
and additional problems may be created.

Step 3051-1
Identify the SCSI bus which the problem is occurring on by examining the hardware error log. The
hardware error log may be viewed as follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapter resources if the adapter resource is not known.
5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem which sent
you here and select it.

Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.

62 PCI-X SCSI RAID Controller: Reference Guide for AIX

6. Select the hardware error log to view. Viewing the hardware error log, under the Disk Information
heading, the Location field can be used to identify which SCSI bus the error is associated with (that is
the SCSI bus is the value EF given a location of EF-G,H).
7. Go to Step 3051-2.

Step 3051-2
While the error persists, replace the components of the failing SCSI bus in the following order.
1. Cable (if present)
2. Adapter (if SCSI bus interface logic is on the adapter) or system board (if SCSI bus interface logic is
on the system board)
3. DASD backplane (if present)
To replace a component and see if the problem was corrected, do the following:
1. Power off the system/logical partition
2. Replace a component listed above
3. Power on the system/logical partition, and run diagnostics in system verification mode on the adapter
When the problem is resolved then go to MAP 0410: Repair Checkout, in RS/6000 Eserver pSeries
Diagnostic Information for Multiple Bus Systems.

MAP 3090
The problem that occurred is uncommon or complex to resolve. Information should be gathered and
assistance obtained from your service support organization.

Step 3090-1
Record the hardware error log. The hardware error log may be viewed as follows:
1. Start Diagnostics and select Task Selection on the Function Selection screen.
2. Select Display Hardware Error Report.
3. Select Display Hardware Errors for PCI-X SCSI RAID Adapters.
4. Select the adapter resource, or select all adapters resources if the adapter resource is not known.
5. On the Error Summary screen, look for an entry with a SRN corresponding to the problem which sent
you here and select it.

Note: If multiple entries exist for the SRN, some entries could be older versions or a problem has
occurred on multiple entities (such as adapters, disk arrays, and devices). Older entries can be
ignored, however, this MAP may need to be used multiple times if the same problem has
occurred on multiple entities.
6. Select the hardware error log to view.
7. Go to Step 3090-2.

Step 3090-2
Collect any hardware error logged about the same time for the adapter.

Go to Step 3090-3.

Step 3090-3
Collect the current disk array configuration. The disk array configuration may be viewed as follows:
1. Start the PCI-X SCSI Disk Array Manager.
a. Start Diagnostics and select Task Selection on the Function Selection screen.
b. Select RAID Array Manager.
c. Select PCI-X SCSI Disk Array Manager.
2. Select List PCI-X SCSI Disk Array Configuration.

Chapter 5. Problem Determination and Recovery 63

3. Select the PCI-X SCSI RAID Controller identified in the hardware error log.
4. Go to Step 3090-4.

Step 3090-4
Contact your service support organization.

Exit this procedure.

Finding an SRN Given an AIX Error Log

Normally Error Log Analysis (ELA) will examine the error logs and present a Service Request Number
(SRN) to the user as appropriate. If you need to determine an SRN given an AIX error log, perform the
following steps:
1. Display the error log using the AIX errpt command (for example errpt for a summary followed by
errpt -a -s timestamp or errpt -a -N resource_name).
2. Ensure that the Error ID is of the form SISIOA_xxxx (for example SISIOA_ARY_DEGRADED).

Note: Only Error IDs of the form SISIOA_xxxx are potentially related to disk arrays.
3. Locate the SENSE DATA in the Detail Data.
4. Identify the bytes 24-27 of the SENSE DATA from the 32 bytes shown.

Note: Use the following example AIX Error Log to help you identify bytes 24-27.
5. The first four digits of the SRN, known as the Failing Function Code (FFC), can be found in the
following table:

Feature Code (bytes 24-25) of SENSE DATA Failing Function Code (FFC)
5703 2523
5709 2523

6. The second four digits of the SRN, known as the Reason Code is equal to bytes 26-27 of the SENSE
DATA

For the example error log:

v Bytes 24-27 of the SENSE DATA are 5703 9030
v The first four digits of the SRN, using 5703 in the table above, is 2523
v The second four digits of the SRN is 9030
v Thus the SRN would be 2323 - 9030

Example AIX Error Log (Error ID = SISIOA_ARY_DEGRADED)

LABEL: SISIOA_ARY_DEGRADED
IDENTIFIER: 8267403B
Date/Time: Wed Dec 11 15:19:54 CST
Sequence Number: 2600
Machine Id: 000B51FD4C00
Node Id: rokon
Class: H
Type: TEMP
Resource Name: sisioa0
Resource Class: adapter
Resource Type: 14107802
Location: 17-08
VPD:
Product Specific.( ).......PCI-X Dual Channel Ultra320 SCSI RAID
Adapter
Part Number.................21P6477
FRU Number..................21P6477

64 PCI-X SCSI RAID Controller: Reference Guide for AIX

 Serial Number...............YL3382127011
Manufacture ID..............0038
EC Level....................3
ROM Level.(alterable).......03090025
Product Specific.(Z0).......58
Device Specific.(YL)........U0.2-P1-I1

Description
DISK ARRAY PROTECTION SUSPENDED

Recommended Actions
PERFORM PROBLEM DETERMINATION PROCEDURES

Detail Data
SENSE DATA
00FF FFFF 1900 00F0 066B 0200 0201 0000 0309 0025 0000 0004 5703 9030 0000 0000
^ ^
| |
| Last 4-digits of SRN (bytes 26-27)
Feature Code of Controller (bytes 24-25)
ARRAY INFORMATION
Location S/N RAID Level
ff-0,0 23897FFD 5

DEGRADED DISK S/N

0023ABA7

ARRAY MEMBER INFORMATION

Expected Actual Vendor/
Location Location Product ID S/N
00-2,0 00-2,0 IBM DFHSS4W 00661BF3
00-1,0 00-1,0 IBM DFHSS4W 002395F4
00-3,0 00-3,0 IBM DFHSS4W 0023ABA7
00-4,0 00-4,0 IBM DFHSS4W 000F4089
00-5,0 00-5,0 IBM DFHSS4W 001B10F2

ADDITIONAL HEX DATA

E210 0080 0400 0000 06F0 0017 00BF 632B 0000 0000 0000 036C 066B 0200 00FF FFFF
FFFF FFFF 1705 B004 0000 0000 0000 0000 0000 0000 0000 0000 2020 2020 2020 2020
2020 2020 2020 2020 2020 2020 2020 2020 3030 3030 3030 3030 0000 0000

Chapter 5. Problem Determination and Recovery 65

66 PCI-X SCSI RAID Controller: Reference Guide for AIX
Appendix A. Communications Statements
The following statement applies to this product. The statement for other products intended for use with this
product appears in their accompanying documentation.

Federal Communications Commission (FCC) Statement

Note: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission
limits. Neither the provider nor the manufacturer is responsible for any radio or television interference
caused by using other than recommended cables and connectors or by unauthorized changes or
modifications to this equipment. Unauthorized changes or modifications could void the users authority to
operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

European Union (EU) Statement

This product is in conformity with the protection requirements of EU Council Directive 89/336/EEC on the
approximation of the laws of the Member States relating to electromagnetic compatibility. The
manufacturer cannot accept responsibility for any failure to satisfy the protection requirements resulting
from a non-recommended modification of the product, including the fitting of option cards supplied by third
parties. Consult with your dealer or sales representative for details on your specific hardware.

This product has been tested and found to comply with the limits for Class A Information Technology
Equipment according to CISPR 22 / European Standard EN 55022. The limits for Class A equipment were
derived for commercial and industrial environments to provide reasonable protection against interference
with licensed communication equipment.

Attention: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.

International Electrotechnical Commission (IEC) Statement

This product has been designed and built to comply with IEC 60950.

United Kingdom Telecommunications Safety Requirements

This equipment is manufactured to the International Safety Standard EN60950 and as such is approved in
the UK under the General Approval Number NS/G/1234/J/100003 for indirect connection to the public
telecommunication network.

The network adapter interfaces housed within this equipment are approved separately, each one having its
own independent approval number. These interface adapters, supplied by the manufacturer, do not use or
contain excessive voltages. An excessive voltage is one which exceeds 70.7 V peak ac or 120 V dc. They

67
interface with this equipment using Safe Extra Low Voltages only. In order to maintain the separate
(independent) approval of the manufacturers adapters, it is essential that other optional cards, not
supplied by the manufacturer, do not use main voltages or any other excessive voltages. Seek advice from
a competent engineer before installing other adapters not supplied by the manufacturer.

Avis de conformit aux normes du ministre des Communications du

Canada
Cet appareil numrique de la classe A est conforme la norme NMB-003 du Canada.

Canadian Department of Communications Compliance Statement

This Class A digital apparatus complies with Canadian ICES-003..

VCCI Statement

The following is a summary of the VCCI Japanese statement in the box above.

This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio
disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

Electromagnetic Interference (EMI) Statement - Taiwan

The following is a summary of the EMI Taiwan statement above.

Warning: This is a Class A product. In a domestic environment this product may cause radio interference
in which case the user will be required to take adequate measures.

Radio Protection for Germany

Dieses Gert ist berechtigt in bereinstimmung mit Dem deutschen EMVG vom 9.Nov.92 das
EGKonformittszeichen zu fhren.

Der Aussteller der Konformittserklrung ist die IBM Germany.

Dieses Gert erfllt die Bedingungen der EN 55022 Klasse A. Fr diese von Gerten gilt folgende
Bestimmung nach dem EMVG:

68 PCI-X SCSI RAID Controller: Reference Guide for AIX

Gerte drfen an Orten, fr die sie nicht ausreichend entstrt sind, nur mit besonderer Genehmigung des
Bundesministers fr Post und Telekommunikation oder des Bundesamtes fr Post und Telekommunikation
betrieben werden. Die Genehmigung wird erteilt, wenn keine elektromagnetischen Strungen zu erwarten
sind.

(Auszug aus dem EMVG vom 9.Nov.92, Para.3, Abs.4)

Hinweis

Dieses Genehmigungsverfahren ist von der Deutschen Bundespost noch nicht verffentlicht worden.

Appendix A. Communications Statements 69

70 PCI-X SCSI RAID Controller: Reference Guide for AIX
Appendix B. Notices
This information was developed for products and services offered in the U.S.A.

The manufacturer may not offer the products, services, or features discussed in this document in other
countries. Consult the manufacturers representative for information on the products and services currently
available in your area. Any reference to the manufacturers product, program, or service is not intended to
state or imply that only that product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any intellectual property right of the manufacturer may be used
instead. However, it is the users responsibility to evaluate and verify the operation of any product,
program, or service.

The manufacturer may have patents or pending patent applications covering subject matter described in
this document. The furnishing of this document does not give you any license to these patents. You can
send license inquiries, in writing, to the manufacturer.

The following paragraph does not apply to the United Kingdom or any country where such
provisions are inconsistent with local law: THIS MANUAL IS PROVIDED AS IS WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain
transactions; therefore, this statement may not apply to you.

This information could include technical inaccuracies or typographical errors. Changes are periodically
made to the information herein; these changes will be incorporated in new editions of the publication. The
manufacturer may make improvements and/or changes in the product(s) and/or the program(s) described
in this publication at any time without notice.

Information concerning products made by other than the manufacturer was obtained from the suppliers of
those products, their published announcements, or other publicly available sources. The manufacturer has
not tested those products and cannot confirm the accuracy of performance, compatibility or any other
claims related to products made by other than the manufacturer. Questions on the capabilities of products
made by other than the manufacturer should be addressed to the suppliers of those products.

71
72 PCI-X SCSI RAID Controller: Reference Guide for AIX
Appendix C. AIX Command-Line Interface
Many tasks used to manage the PCI-X SCSI RAID Controller can be performed by using the AIX
command line instead of using the PCI-X SCSI Disk Array Manager as described throughout this guide.
The following table summarizes these commands.

General Help sisraidmgr -h

Viewing the Disk Array Configuration on page 15 sisraidmgr -Ll controller name -j1
Preparing Disks for Use in PCI-X SCSI Disk Arrays on sisraidmgr -P -z disk list (For example, sisraidmgr -P -z
page 14 `hdisk1 hdisk2 pdisk3 pdisk4)
Changing pdisks to hdisks on page 24 sisraidmgr -U -z `pdisk list
Creating a PCI-X SCSI Disk Array on page 14 sisraidmgr -C -r `raid level -s `stripe size -z `pdisk list
Deleting a PCI-X SCSI Disk Array on page 17 sisraidmgr -D -l controller name -d `array name
Adding Disks to an Existing Disk Array on page 17 sisraidmgr -A -l `array name -z `pdisk list
Creating Hot Spare Disks on page 18 sisraidmgr -H -z `pdisk list
Deleting Hot Spare Disks on page 19 sisraidmgr -I -z `pdisk list
Displaying Rechargeable Battery Information on page sisraidmgr -M -o0 -l adapter name
24
Forcing a Rechargeable Battery Error on page 26 sisraidmgr -M -o1 -l adapter name
Recovery Procedures for Disk Failures on page 28 sisraidmgr -R -z pdisk list

73
74 PCI-X SCSI RAID Controller: Reference Guide for AIX
Index
A hot spare
adding disks 18
adding disk to existing array 17
deleting disks 19
AIX command-line interface 73
Hot Spare Disks 18
avoiding shock hazard v

B L
location codes 31
battery
displaying information 24
error, forcing 26
bus settings
M
viewing and changing 19 Maintenance Analysis Procedures (MAPs) 34
maintenance tips 23
MAP 3000 34
C MAP 3010 35
MAP 3011 38
Cache Battery Pack
MAP 3012 40
replacing 26
MAP 3013 41
capacities, disk array 7
MAP 3020 43
checkpoints 34
MAP 3021 45
command-line interface 73
MAP 3030 45
common tasks 13
MAP 3031 46
controller microcode, updating 24
MAP 3032 50
creating disk array 14
MAP 3033 51
creating disks hot spare 18
MAP 3034 52
MAP 3035 55
MAP 3036 56
D MAP 3050 57
deleting disks hot spare 19 MAP 3051 62
deleting, disk array 17 MAP 3090 63
description
RAID Level 0 4
RAID Level 10 6
RAID Level 5 5
O
overview, controller 1
disk array
overview, disk arrays 7
adding disk to an existing 17
deleting 17
viewing configuration 15
disk array problems
P
identifying 32 PCI-X SCSI Disk Array Manager, using 13
disk array settings pdisk descriptions 9
viewing 21 pdisk settings
disk array settings, viewing 21 viewing 21
disk array states 8 pdisks
disk array, capacities 7 replacing 27
disk arrays, definitions 2 pdisks, changing to hdisks 24
disk arrays, overview 7 physical disks (pdisks), states 9
preparing disks for disk array use 14
problem determination 31
E
examples
AIX error log 64
R
RAID Level
recovery procedures 28
H RAID Level 0 4
recovery procedures 28
hdisks, changing from pdisks 24
RAID Level 10 6
highlighting ix
recovery procedures 28

75
RAID Level 5 5
RAID Levels 3, 7
rechargeable battery error, forcing 26
rechargeable battery information, displaying 24
Rechargeable Battery Maintenance 24
rechargeable Cache Battery Pack, replacing 26
recovery 31
recovery procedures
RAID Level 0 28
RAID Level 10 28
RAID Level 5 28
related publications ix

S
Service Request Number (SRN) Table 32
shock hazard, avoiding v
software, verifying installation 11
SRN
finding 64
table 32
states
disk arrays (hdisks) 8
physical disks (pdisks) 9
stripe-unit size 7
summary, RAID Level 7

V
verifying installation of controller software 11
viewing
disk array settings 21
viewing and changing, bus settings 19
viewing disk array configuration 15

76 PCI-X SCSI RAID Controller: Reference Guide for AIX

Vos remarques sur ce document / Technical publication remark form
Titre / Title : Bull ESCALA PCIX SCSI RAID Controller Reference Guide

N Refrence / Reference N : 86 A1 22EM 00 Dat / Dated : November 2003

ERREURS DETECTEES / ERRORS IN PUBLICATION

AMELIORATIONS SUGGEREES / SUGGESTIONS FOR IMPROVEMENT TO PUBLICATION

Vos remarques et suggestions seront examines attentivement.

Si vous dsirez une rponse crite, veuillez indiquer ci-aprs votre adresse postale complte.
Your comments will be promptly investigated by qualified technical personnel and action will be taken as required.
If you require a written reply, please furnish your complete mailing address below.

NOM / NAME : Date :

SOCIETE / COMPANY :
ADRESSE / ADDRESS :

Remettez cet imprim un responsable BULL ou envoyez-le directement :

Please give this technical publication remark form to your BULL representative or mail to:

BULL CEDOC
357 AVENUE PATTON
B.P.20845
49008 ANGERS CEDEX 01
FRANCE
Technical Publications Ordering Form
Bon de Commande de Documents Techniques

To order additional publications, please fill up a copy of this form and send it via mail to:
Pour commander des documents techniques, remplissez une copie de ce formulaire et envoyez-la :

BULL CEDOC
ATTN / Mr. L. CHERUBIN Phone / Tlphone : +33 (0) 2 41 73 63 96
357 AVENUE PATTON FAX / Tlcopie +33 (0) 2 41 73 60 19
B.P.20845 EMail / Courrier Electronique : [email protected]
49008 ANGERS CEDEX 01
FRANCE

Or visit our web sites at: / Ou visitez nos sites web :

http://www.logistics.bull.net/cedoc
http://wwwfrec.bull.com http://www.bull.com

CEDOC Reference # Qty CEDOC Reference # Qty CEDOC Reference # Qty

No Rfrence CEDOC Qt No Rfrence CEDOC Qt No Rfrence CEDOC Qt

__ __ ____ _ [__] __ __ ____ _ [__] __ __ ____ _ [__]

__ __ ____ _ [__] __ __ ____ _ [__] __ __ ____ _ [__]

__ __ ____ _ [__] __ __ ____ _ [__] __ __ ____ _ [__]

__ __ ____ _ [__] __ __ ____ _ [__] __ __ ____ _ [__]

__ __ ____ _ [__] __ __ ____ _ [__] __ __ ____ _ [__]

__ __ ____ _ [__] __ __ ____ _ [__] __ __ ____ _ [__]

__ __ ____ _ [__] __ __ ____ _ [__] __ __ ____ _ [__]

[ _ _ ] : no revision number means latest revision / pas de numro de rvision signifie rvision la plus rcente

NOM / NAME : Date :

SOCIETE / COMPANY :
ADRESSE / ADDRESS :

PHONE / TELEPHONE : FAX :

EMAIL :

For Bull Subsidiaries / Pour les Filiales Bull :

Identification:

For Bull Affiliated Customers / Pour les Clients Affilis Bull :

Customer Code / Code Client :

For Bull Internal Customers / Pour les Clients Internes Bull :

Budgetary Section / Section Budgtaire :

For Others / Pour les Autres :

Please ask your Bull representative. / Merci de demander votre contact Bull.
 PLACE BAR CODE IN LOWER
LEFT CORNER

BULL CEDOC
357 AVENUE PATTON
B.P.20845
49008 ANGERS CEDEX 01
FRANCE

ORDER REFERENCE
86 A1 22EM 00
Utiliser les marques de dcoupe pour obtenir les tiquettes.
Use the cut marks to get the labels.

ESCALA

PCIX SCSI RAID

Controller
Reference Guide

86 A1 22EM 00

ESCALA

PCIX SCSI RAID

Controller
Reference Guide

86 A1 22EM 00

ESCALA

PCIX SCSI RAID

Controller
Reference Guide

86 A1 22EM 00