Scribd
Upload
44 views

Overview:: Figure 1: The Total Structure Rendered With Correct Cross-Section

1) A beam model 400mm long and with a cross section of 25mm by 50mm was analyzed under a 10000N central load. 2) The maximum displacement of 0.91641E-07mm occurred at node 7 near the center of the beam. 3) Node 1 experienced a moment force of 0.74254E+06 reported in the results.

Uploaded by

Cris Demby
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
44 views

Overview:: Figure 1: The Total Structure Rendered With Correct Cross-Section

1) A beam model 400mm long and with a cross section of 25mm by 50mm was analyzed under a 10000N central load. 2) The maximum displacement of 0.91641E-07mm occurred at node 7 near the center of the beam. 3) Node 1 experienced a moment force of 0.74254E+06 reported in the results.

Uploaded by

Cris Demby
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Homework #4

02/17/2016

Christopher Demby

Overview:
The model is shown in Figure 1 as the total structure. This is a beam that is 25mm by 50mm cross-
section that is 400mm long. The element consists of a meshing size of ten separations. The loading that
is applied is in the center of the beam at 10000N, which applies a bending stress on the beam, which is
seen in Figure 2. At key point 1, the point is constrained in all degrees of freedom.at the other end, key
point 2, the constraint is only applied in the y axis, due to the point being a roller point.

Figure 1: The total structure rendered with correct cross-section.


Figure 2:The deformation in the beam with the outline of the original dimensions.

Analysis:

Below, the results are shown. The nodes experience strain, with the maximum being experienced in
node 7. Node 1 experiences a moment force that is displayed in the bottom results. The forces that act
in each node can also be reviewed below. Here, the increase of displacement can be seen closer to the
center of the structure at node which agrees with the deformation of the structure in Figure 2.

PRINT U NODAL SOLUTION PER NODE

***** POST1 NODAL DEGREE OF FREEDOM LISTING *****

LOAD STEP= 1 SUBSTEP= 1


TIME= 1.0000 LOAD CASE= 0

THE FOLLOWING DEGREE OF FREEDOM RESULTS ARE IN THE GLOBAL COORDINATE SYSTEM

NODE UX UY UZ USUM
1 0.0000 0.0000 0.0000 0.0000
2 0.0000 0.0000 0.0000 0.0000
3 0.0000 -0.94976E-08 0.0000 0.94976E-08
4 0.0000 -0.29651E-07 0.0000 0.29651E-07
5 0.0000 -0.54220E-07 0.0000 0.54220E-07
6 0.0000 -0.76964E-07 0.0000 0.76964E-07
7 0.0000 -0.91641E-07 0.0000 0.91641E-07
8 0.0000 -0.90482E-07 0.0000 0.90482E-07
9 0.0000 -0.77876E-07 0.0000 0.77876E-07
10 0.0000 -0.56686E-07 0.0000 0.56686E-07
11 0.0000 -0.29774E-07 0.0000 0.29774E-07

MAXIMUM ABSOLUTE VALUES


NODE 0 7 0 7
VALUE 0.0000 -0.91641E-07 0.0000 0.91641E-07

PRINT REACTION SOLUTIONS PER NODE

***** POST1 TOTAL REACTION SOLUTION LISTING *****

LOAD STEP= 1 SUBSTEP= 1


TIME= 1.0000 LOAD CASE= 0

THE FOLLOWING X,Y,Z SOLUTIONS ARE IN THE GLOBAL COORDINATE SYSTEM

NODE FX FY FZ MX MY MZ
1 0.0000 6856.4 0.0000 0.89005E-11-0.21144E-11 0.74254E+06
2 3143.6

TOTAL VALUES
VALUE 0.0000 10000. 0.0000 0.89005E-11-0.21144E-11 0.74254E+06
PRINT ROT NODAL SOLUTION PER NODE

***** POST1 NODAL DEGREE OF FREEDOM LISTING *****

LOAD STEP= 1 SUBSTEP= 1


TIME= 1.0000 LOAD CASE= 0

THE FOLLOWING DEGREE OF FREEDOM RESULTS ARE IN THE GLOBAL COORDINATE SYSTEM

NODE ROTX ROTY ROTZ RSUM


1 0.0000 0.0000 0.0000 0.0000
2 0.0000 0.0000 0.73232E-09 0.73232E-09
3 0.0000 0.0000 -0.34441E-09 0.34441E-09
4 0.0000 0.0000 -0.53281E-09 0.53281E-09
5 0.0000 0.0000 -0.56518E-09 0.56518E-09
6 0.0000 0.0000 -0.44154E-09 0.44154E-09
7 0.0000 0.0000 -0.16187E-09 0.16187E-09
8 0.0000 0.0000 0.16004E-09 0.16004E-09
9 0.0000 0.0000 0.41041E-09 0.41041E-09
10 0.0000 0.0000 0.58925E-09 0.58925E-09
11 0.0000 0.0000 0.69656E-09 0.69656E-09

MAXIMUM ABSOLUTE VALUES


NODE 0 0 2 2
VALUE 0.0000 0.0000 0.73232E-09 0.73232E-09

PRINT SUMMED NODAL LOADS

***** POST1 SUMMED TOTAL NODAL LOADS LISTING *****

LOAD STEP= 1 SUBSTEP= 1


TIME= 1.0000 LOAD CASE= 0

THE FOLLOWING X,Y,Z SOLUTIONS ARE IN THE GLOBAL COORDINATE SYSTEM

NODE FX FY FZ MX MY MZ
1 -6856.4 -0.89005E-11 0.21144E-11-0.74254E+06
2 -3143.6 -0.40809E-11 0.21958E-12
3 -0.95782E-12
4 -0.95782E-12
5 -0.95782E-12
6 -0.95782E-12
7 10000. 0.12981E-10-0.25933E-12
8 0.43916E-12
9 0.43916E-12
10 0.43916E-12
11 0.43916E-12

TOTAL VALUES
VALUE 0.0000 -0.54570E-10 0.0000 -0.71086E-25-0.10097E-27-0.74254E+06

You might also like