Course Title: STRENGTH OF MATERIALS

[As per Choice Based Credit System (CBCS) scheme]

SEMESTER III
Subject Code 15CV32 I.A. Marks 20
Number of Lecture Hours/Week 04 Exam. Marks 80
Total Number of Lecture Hours 50 Exam. Hours 03
CREDITS 04
Course objectives: This course will enable students;
1. To understand the basic concepts of the stresses and strains for different
materials and strength of structural elements.
2. To know the development of internal forces and resistance mechanism for one
dimensional and two dimensional structural elements.
3. To analyse and understand different internal forces and stresses induced due
to representative loads on structural elements.
4. To analyse and understand principal stresses due to the combination of two
dimensional stresses on an element and failure mechanisms in materials.
5. To evaluate the behavior of torsional members, columns and struts.
Revised
Modules Teaching Blooms
Hours Taxonomy
(RBT) Level
Module -1:
Simple Stresses and Strain: 10 Hours L2,L3
Introduction, Definition and concept and of stress
and strain. Hookes law, Stress-Strain diagrams for
ferrous and non-ferrous materials, factor of safety,
Elongation of tapering bars of circular and
rectangular cross sections, Elongation due to self-
weight.
Saint Venants principle, Compound bars,
Temperature stresses, Compound section subjected
to temperature stresses, state of simple shear,
Elastic constants and their relationship.
Module -2:
Compound Stresses: 5 Hours L2,L4
Introduction, state of stress at a point, General two
dimensional stress system, Principal stresses and
principal planes. Mohrs circle of stresses
Thin and Thick Cylinders:
Introduction, Thin cylinders subjected to internal 5 Hours L2,L4
pressure; Hoop stresses, Longitudinal stress and
change in volume. Thick cylinders subjected to
both internal and external pressure; Lames
equation, radial and hoop stress distribution.

Module-3:

1
Shear Force and Bending Moment in Beams: 10 Hours L2,L4
Introduction to types of beams, supports and
loadings. Definition of bending moment and shear
force, Sign conventions, relationship between load
intensity, bending moment and shear force. Shear
force and bending moment diagrams for statically
determinate beams subjected to points load,
uniformly distributed loads, uniformly varying
loads, couple and their combinations.
Module -4:
Bending and Shear Stresses in Beams: 6 Hours L2.L4
Introduction, pure bending theory, Assumptions,
derivation of bending equation, modulus of
rupture, section modulus, flexural rigidity.
Expression for transverse shear stress in beams,
Bending and shear stress distribution diagrams for
circular, rectangular, I, and T sections.
Shear centre(only concept)
Columns and Struts: 4 Hours L2,L4
Introduction, short and long columns. Eulers
theory; Assumptions, Derivation for Eulers
Buckling load for different end conditions,
Limitations of Eulers theory. Rankine-Gordons
formula for columns.
Module -5:
Torsion in Circular Shaft: 7 Hours L2,L4
Introduction, pure torsion, Assumptions, derivation
of torsion equation for circular shafts, torsional
rigidity and polar modulus Power transmitted by a
shaft, combined bending and torsion.
Theories of Failure:
Introduction, maximum principal stress theory 3 Hours L1,L2
(Rankines theory), Maximum shearing stress
theory (Trescas theory), Strain energy theory
(Beltrami and Haigh), and maximum strain theory
(St. Venants theory).

2
Course outcomes:
After studying this course, students will be able;
1. To evaluate the strength of various structural elements internal forces
such as compression, tension, shear, bending and torsion.
2. To suggest suitable material from among the available in the field of
construction and manufacturing.
3. To evaluate the behavior and strength of structural elements under the
action of compound stresses and thus understand failure concepts.
4. To understand the basic concept of analysis and design of members
subjected to torsion.
5. To understand the basic concept of analysis and design of structural
elements such as columns and struts.
Program Objectives (as per NBA)
o Engineering Knowledge.
o Problem Analysis.
o Interpretation of data.
Question paper pattern:
The question paper will have Ten questions, each full question carrying
16 marks.
There will be two full questions (with a maximum three sub divisions, if
necessary) from each module.
Each full question shall cover the topics under a module.
The students shall answer Five full questions selecting one full
question from each module.
If more than one question is answered in modules, best answer will be
considered for the award of marks limiting one full question answer in
each module.
Text Books:
1. B.S. Basavarajaiah, P.Mahadevappa Strength of Materials in SI
Units, University Press (India) Pvt. Ltd., 3rd Edition, 2010
2. Ferdinand P. Beer, E. Russell Johnston and Jr.John T. DeWolf
Mechanics of Materials, Tata McGraw-Hill, Third Edition, SI Units
Reference Books:
1. D.H. Young, S.P. Timoshenko Elements of Strength of Materials
East West Press Pvt. Ltd., 5th Edition (Reprint 2014)
2. R K Bansal, A Textbook of Strength of Materials, 4th Edition, Laxmi
Publications, 2010
3. S.S. Rattan Strength of Materials McGraw Hill Education (India)
Pvt. Ltd., 2nd Edition (Sixth reprint 2013)
4. Vazirani, V N, Ratwani M M. and S K Duggal "Analysis of Structures
Vol. I", 17th Edition, Khanna Publishers, New Delhi.

3
 Course Title: FLUIDS MECHANICS
[As per Choice Based Credit System (CBCS) scheme]
SEMESTER III
Subject Code 15CV33 IA Marks 20
Number of Lecture Hours/Week 04 Exam Marks 80
Total Number of Lecture Hours 50 Exam Hours 03
CREDITS 04
Course objectives:
The objectives of this course is to make students to learn:
1. The Fundamental properties of fluids and its applications.
2. Hydrostatic laws and application to practical problem solving
3. Principles of Kinematics and Hydro-Dynamics for practical applications
4. Basic design of pipes and pipe networks considering flow, pressure and
its losses.
5. The basic flow rate measurements

Revised
Modules Teaching Blooms
Hours Taxonomy
(RBT)
Level
Module -1
Fluids & Their Properties: 5 Hours L2,L3
Concept of fluid, Systems of units. Properties of
fluid; Mass density, Specific weight, Specific
gravity, Specific volume, Viscosity, Cohesion,
Adhesion, Surface tension& Capillarity. Fluid as a
continuum, Newtons law of viscosity (theory &
problems).Capillary rise in a vertical tube and
between two plane surfaces (theory & problems).
vapor pressure of liquid, compressibility and bulk
modulus, capillarity, surface tension, pressure
inside a water droplet, pressure inside a soap
bubble and liquid jet. Numerical problems

Fluid Pressure and Its Measurements: 5 Hours L2,L3

Definition of pressure, Pressure at a point,
Pascals law, Variation of pressure with depth.
Types of pressure. Measurement of pressure using
simple, differential & inclined manometers (theory
& problems). Introduction to Mechanical and
electronic pressure measuring devices.

4
Module -2
Hydrostatic forces on Surfaces : 3 Hours L2,L4
Definition, Total pressure, centre of pressure, total
pressure on horizontal, vertical and inclined plane
surface, total pressure on curved surfaces, water
pressure on gravity dams, Lock gates. Numerical
Problems.

Fundamentals of fluid flow (Kinematics):

7 Hours L2,L4
Introduction. Methods of describing fluid motion.
Velocity and Total acceleration of a fluid particle.
Types of fluid flow, Description of flow pattern.
Basic principles of fluid flow, three-dimensional
continuity equation in Cartesian coordinate
system. Derivation for Rotational and irroational
motion. Potential function, stream function,
orthogonality of streamlines and equipotential
lines. Numerical problems on Stream function and
velocity potential.
Introduction to flow net.

Module -3
Fluid Dynamics: 10 Hours L2,L4
Introduction. Forces acting on fluid in motion.
Eulers equation of motion along a streamline and
Bernoullis equation. Assumptions and limitations
of Bernoullis equation. Modified Bernoullis
equation. Problems on applications of Bernoullis
equation (with and without losses).
Vortex motion; forced vortex, free vortex, problems
Momentum equation problems on pipe bends.
Applications:
Introduction. Venturimeter, Orificemeter, Pitot
tube. Numerical Problems
Module -4
Orifice and Mouthpiece: 3 Hours L1,L2
Introduction, classification, flow through orifice,
hydraulic coefficients, Numerical problems.
Mouthpiece, classification, Bordas Mouthpiece
(No problems).
Notches and Weirs:
Introduction. Classification, discharge over 7 Hours L2,L4
rectangular, triangular, trapezoidal notches,
Cippoletti notch, broad crested weirs. Numerical
problems. Ventilation of weirs, submerged weirs.

5
Module -5
Flow through Pipes: 7 Hours L2,L4
Introduction. Major and minor losses in pipe flow.
Darcy-Weisbach equation for head loss due to
friction in a pipe. Pipes in series, pipes in parallel,
equivalent pipe-problems. Minor losses in pipe
flow, equation for head loss due to sudden
expansion. Numerical problems.
Hydraulic gradient line, energy gradient line.
Pipe Networks, Hardy Cross method, Numerical
problems.
Surge Analysis in Pipes:
3 Hours L2,L4
Water hammer in pipes, equations for pressure
rise due to gradual valve closure and sudden
closure for rigid and elastic pipes. Problems
Course outcomes:
After successful completion of the course, the student will be able to:
1. Possess a sound knowledge of fundamental properties of fluids and
fluid continuum
2. Compute and solve problems on hydrostatics, including practical
applications
3. Apply principles of mathematics to represent kinematic concepts
related to fluid flow
4. Apply fundamental laws of fluid mechanics and the Bernoullis
principle for practical applications
5. Compute the discharge through pipes and over notches and weirs
Program Objectives (as per NBA)
o Engineering Knowledge.
o Problem Analysis.
o Interpretation of data.
Question paper pattern:
The question paper will have Ten questions, each full question carrying
16 marks.
There will be two full questions (with a maximum Three sub divisions, if
necessary) from each module.
Each full question shall cover the topics under a module.
The students shall answer Five full questions selecting one full question
from each module.
If more than one question is answered in modules, best answer will be
considered for the award of marks limiting one full question answer in
each module.

6
Text Books:
1. P N Modi and S M Seth, Hydraulics and Fluid Mechanics, including
Hydraulic Machines, 20th edition, 2015, Standard Book House, New
Delhi
2. R.K. Bansal, A Text book of Fluid Mechanics and Hydraulic
Machines, Laxmi Publications, New Delhi
3. S K SOM and G Biswas, Introduction to Fluid Mechanics and Fluid
Machines, Tata McGraw Hill,New Delhi
Reference Books:
1. Victor L Streeter, Benjamin Wylie E and Keith W Bedford, Fluid
Mechanics, Tata McGraw Hill Publishing Co Ltd., New Delhi,
2008(Ed)
2. K Subramanya, Fluid Mechanics and Hydraulic Machines, Tata
McGraw Hill Publishing Co. Ltd.
3. K Subramanya, Fluid Mechanics and Hydraulic Machines-problems
and solutions, Tata McGraw Hill Publishing Co. Ltd.
4. J. F. Douglas, J. M. Gasoriek, John Swaffield, Lynne Jack,
Fluid Mechanics, Pearson, Fifth Edition
5. Mohd.Kaleem Khan, Fluid Mechanics and Machinery, Oxford
University Press

7
 Course Title: BASIC SURVEYING
[As per Choice Based Credit System (CBCS) scheme]
SEMESTER III
Subject Code 15CV34 IA Marks 20
Number of Lecture Hours/Week 04 Exam Marks 80
Total Number of Lecture Hours 50 Exam Hours 03
CREDITS 04
Course objectives:
This course will enable students to;
1. Understand the basic principles of Surveying
2. Learn Linear and Angular measurements to arrive at solutions to basic
surveying problems.
3. Employ conventional surveying data capturing techniques and process the
data for computations.
4. Analyze the obtained spatial data to compute areas and volumes and draw
contours to represent 3D data on plane figures.
Revised
Modules Teaching Blooms
Hours Taxonomy
(RBT) Level
Module -1
Introduction: 6 Hours L1, L2
Definition of surveying, Objectives and importance of
surveying. Classification of surveys. Principles of
surveying. Units of measurements, Surveying
measurements and errors, types of errors, precision
and accuracy. Classification of maps, map scale,
conventional symbols, topographic maps, map
layout, Survey of India Map numbering systems.
Measurement of Horizontal Distances:
Measuring tape and types. Measurement using 4 Hours L1, L2
tapes, Taping on level ground and sloping ground.
Errors and corrections in tape measurements,
ranging of lines, direct and indirect methods of
ranging, Electronic distance measurement, basic
principle. Booking of tape survey work, Field book,
entries, Conventional symbols, Obstacles in tape
survey, Numerical problems.

8
Module -2
Measurement of Directions and Angles: 5 Hours L2,L3
Compass survey:
Basic definitions; meridians, bearings, magnetic and
True bearings. Prismatic and surveyors compasses,
temporary adjustments, declination. Quadrantal
bearings, whole circle bearings, local attraction and
related problems
Theodolite Survey and Instrument Adjustment: 5 Hours L2,L3
Theodolite and types, Fundamental axes and parts of
Transit theodolite, uses of theodolite, Temporary
adjustments of transit theodolite, measurement of
horizontal and vertical angles, step by step procedure
for obtaining permanent adjustment of Transit
theodolite
Module -3
Traversing: 5 Hours L1, L2
Traverse Survey and Computations: Latitudes and
departures, rectangular coordinates, Traverse
adjustments, Bowditch rule and transit rule,
Numerical Problems
5 Hours L1, L2
Tacheometry:
basic principle, types of tacheometry, distance
equation for horizontal and inclined line of sight in
fixed hair method, problems
Module -4
Leveling: 10Hours L3,L4
Basic terms and definitions, Methods of leveling,
Dumpy level, auto level, digital and laser levels.
Curvature and refraction corrections. Booking and
reduction of levels.
Differential leveling, profile leveling, fly leveling, check
leveling, reciprocal leveling, trigonometric leveling
(heights and distances-single plane and double plane
methods.
Module -5:
Areas and Volumes: 8Hours L2,L3
Measurement of area by dividing the area into
geometrical figures, area from offsets, mid ordinate
rule, trapezoidal and Simpsons one third rule, area
from co-ordinates, introduction to planimeter, digital
planimeter. Measurement of volumes-trapezoidal and
prismoidal formula.
Contouring 2 Hours L2,L3
Contours, Methods of contouring, Interpolation of
contours, contour gradient, characteristics of
contours and uses.

9
Course outcomes:
After a successful completion of the course, the student will be able to:
1. Posses a sound knowledge of fundamental principles Geodetics[L1][PO1]
2. Measurement of vertical and horizontal plane, linear and angular dimensions
to arrive at solutions to basic surveying problems.[L2][L3][PO3]
3. Capture geodetic data to process and perform analysis for survey problems
[L4][PO2]
4. Analyse the obtained spatial data and compute areas and volumes. Represent
3D data on plane figures as contours [L4] [PO2]
Program Objectives (as per NBA)
o Engineering Knowledge.
o Problem Analysis.
o Interpretation of data.
Question paper pattern:
The question paper will have Ten questions, each full question carrying 16
marks.
There will be two full questions (with a maximum Three sub divisions, if
necessary) from each module.
Each full question shall cover the topics under a module.
The students shall answer Five full questions selecting one full question from
each module.
If more than one question is answered in modules, best answer will be
considered for the award of marks limiting one full question answer in each
module.

Text Books:
1. B.C. Punmia, Surveying Vol.1, Laxmi Publications pvt. Ltd., New Delhi
2009.
2. Kanetkar T P and S V Kulkarni , Surveying and Leveling Part I, Pune
Vidyarthi Griha Prakashan, 1988
Reference Books:
1. S.K. Duggal, Surveying Vol.1, Tata McGraw Hill Publishing Co. Ltd. New
Delhi. 2009.
2. K.R. Arora, Surveying Vol. 1 Standard Book House, New Delhi. 2010
3. R Subramanian, Surveying and Leveling, Second edition, Oxford
University Press, New Delhi
4. A. Bannister, S. Raymond , R. Baker, Surveying, Pearson, 7th ed., New
Delhi

10
 Course Title: ENGINEERING GEOLOGY
[As per Choice Based Credit System (CBCS) scheme]
SEMESTER III
Subject Code 15CV35 IA Marks 20
Number of Lecture Hours/Week 04 Exam Marks 80
Total Number of Lecture Hours 50 Exam Hours 03
CREDITS 04
Course objectives:
This course will enable students;
1. To understand the internal structure and composition of the earth.
2. To comprehend the properties, occurrence and uses of minerals in various
industries.
3. To learn about geo-morphological agents such as river, wind, sea waves, and
their implications in implementing civil engineering projects.
4. To gain knowledge about the structures of the rocks and their considerations in
the selection of site for dams, tunnels, bridges and highways.
5. To learn the application of Topographic maps, remote sensing and GIS in Civil
engineering practices and natural resource management.
Revised
Modules Teaching Blooms
Hours Taxonomy
(RBT) Level
Module -1
Introduction: 10 Hours L1,L2
Application of Earth Science in Civil Engineering
Practices, Understanding the earth, internal
structure and composition.
Mineralogy:
Mineral properties, composition and their use in the
manufacture of construction materials - Quartz
Group (Glass); Feldspar Group (Ceramic wares and
Flooring tiles); Kaolin (Paper, paint and textile);
Asbestos (AC sheets); Carbonate Group ( Cement) ;
Gypsum (POP, gypsum sheets, cement); Mica Group
(Electrical industries); Ore minerals - Iron ores
(Steel); Chromite (Alloy); Bauxite (aluminum);
Chalcopyrite (copper)

11
Module -2
Petrology: 10 Hours L2,L3
Formation, Classification and Engineering
Properties. Rock as construction material, concrete
aggregate, railway ballast, roofing, flooring, cladding
and foundation. Deformation of rocks, Development
of Joints, Folds, Faults and Unconformities. Their
impact in the selection of sites for Dams, Reservoirs,
Tunnels, Highways and Bridges, Rock Quality
Determination (RQD), Rock Structure Rating (RSR),:
Igneous Rocks - Granite, Gabbro, Dolerite, Basalt;
Sedimentary rocks - Sandstone, Shale, Limestone,
Laterite; Metamorphic rocks - Gneiss, Quartzite,
Slate, Charnockite: Decorative stones - Porphyries,
Marble and Quartzite.

Module -3
Geomorphology and Seismology: 12 Hours L2, L3, L5
Landforms Classification, Rock weathering, types
and its effects on Civil Engineering Projects. Study of
Geo-morphological aspects in the selection of sites for
Dams, Reservoirs, Tunnels, Highways and Bridges.
Watershed management, Floods and their control,
River valley, Drainage pattern parameters and
development; Coastlines and their engineering
considerations.
Earthquake - Causes and Effects,, Seismic waves,
Engineering problems related to Earthquakes,
Earthquake intensity, Richter Scale, Seismograph,
Seismic zones- World and India, Tsunami causes
and effects. Early warning system. Reservoir Induced
Seismicity; Landslides causes and their control.
Module -4
Hydrogeology: 8 Hours L4,L5
Hydrological cycle, Occurrence of Groundwater in
different terrains -Weathered, Hard and Stratified
rocks; Determination of Quality aspects - SAR, RSC
and TH of Groundwater. Groundwater Pollution,
Groundwater Exploration- Electrical Resistivity and
Seismic methods, Resistivity curves, Water Bearing
Formations, Aquifer types and parameters -
Porosity, Specific yield and retention, Permeability,
Transmissibility and Storage Coefficient. Springs and
Artesian Wells, Artificial Recharging of Groundwater,
Sea water intrusion and remedies.

12
Module -5:
Geodesy: 10 Hours L2,L3, L5
Study of Topographic maps and Contour maps;
Remote Sensing Concept, Application and its
Limitations; Geographic Information System (GIS)
and Global Positioning System (GPS) Concept and
their use resource mapping. LANDSAT Imagery
Definition and its use. Impact of Mining, Quarrying
and Reservoirs on Environment. Natural Disasters
and their mitigation.
Course outcomes:
After a successful completion of the course, the student will be able to:
1. Students will able to apply the knowledge of geology and its role in Civil
Engineering
2. Students will effectively utilize earths materials such as mineral, rocks and
water in civil engineering practices.
3. Analyze the natural disasters and their mitigation.
4. Assess various structural features and geological tools in ground water
exploration,
Natural resource estimation and solving civil engineering problems.
5. Apply and asses use of building materials in construction and asses their
properties
Program Objectives (as per NBA)
o Engineering Knowledge.
o Problem Analysis.
o Interpretation of data.
Question paper pattern:
The question paper will have Ten questions, each full question carrying 16
marks.
There will be two full questions (with a maximum Three sub divisions, if
necessary) from each module.
Each full question shall cover the topics under a module.
The students shall answer Five full questions selecting one full question from
each module.
If more than one question is answered in modules, best answer will be
considered for the award of marks limiting one full question answer in each
module.

Text Books:
1. P.K. Mukerjee, A Text Book of Geology, World Press Pvt., Ltd. Kolkatta.
2. Parbin Singh, Text Book of Engineering and General Geology, Published by
S.K. Kataria and Sons, New Dehli

13
Reference Books:
1. Earthquake Tips - Learning Earthquake Design and Construction - C V R
Murthy Published by National Information Centre of Earthquake Engineering,
Indian Institute of Technology, Kanpur.
2. Dimitri P Krynine and William R Judd, Principles of Engineering Geology and
Geotechnics, CBS Publishers and Distributors, New Delhi.
3. K V G K Gokhale, Principles of Engineering Geology, BS Publications,
Hyderabad.
4. M Anji Reddy, Text book of Remote Sensing and Geographical Information
System, BS Publications, Hyderabad.
5. Ground water Assessment, development and Management by K.R. Karanth,
Tata Mc Graw Hills
6. K. Todd, Groundwater Hydrology, Tata Mac Grow Hill, New Delhi.
7. D. Venkata Reddy, Engineering Geology, New Age International Publications,
New Delhi.
8. S.K Duggal, H.K Pandey and N Rawal, Engineering Geology, McGraw Hill
Education (India) Pvt, Ltd. New Delhi.
9. M.P Billings, Structural Geology, CBS Publishers and Distributors, New Delhi.
10. K. S. Valdiya, Environmental Geology,, Tata Mc Grew Hills.
11. M. B. Ramachandra Rao, Outlines of Geophysical Prospecting- A Manual
for Geologists, Prasaranga, University of Mysore, Myso

14
 Course Title: Building Materials and Construction
[As per Choice Based Credit System (CBCS) scheme]
SEMESTER III
Subject Code 15CV36 IA Marks 20
Number of Lecture Hours/Week 04 Exam Marks 80
Total Number of Lecture Hours 50 Exam Hours 03
CREDITS 04
Course objectives:
This course will develop a student;
1. In recognizing the good materials to be used for the construction work
2. In investigation of soil condition, Deciding and design of suitable
foundation for different structures
3. In supervision of different types of masonry
4. In selection of materials, design and supervision of suitable type of floor
and roof.
5. To gain knowledge about doors, windows, plastering, painting, damp
proofing, scaffolding, shoring, underpinning and to take suitable
engineering measures.
Revised
Teaching Blooms
Modules
Hours Taxonomy
(RBT) Level
Module -1

Building Materials: 10 Hours L1 L2

Stone as building material; Requirement of good
building stones, Dressing of stones, Deterioration
and Preservation of stone work.
Bricks; Classification, Manufacturing of clay
bricks, Requirement of good bricks. Field and
laboratory tests on bricks; compressive strength,
water absorption, efflorescence, dimension and
warpage.
Cement Concrete blocks, Stabilized Mud Blocks,
Sizes, requirement of good blocks. Mortar: types
and requirements. Timber as construction
material
Fine aggregate: Natural and manufactured: Sieve
analysis, zoning, specify gravity, bulking,
moisture content, deleterious materials.
Coarse aggregate: Natural and manufactured:
Importance of size, shape and texture. Grading of
aggregates, Sieve analysis, specific gravity,
Flakiness and elongation index, crushing, impact
and abrasion tests.

Module -2

15
Foundation: 10Hours L1,L2
Preliminary investigation of soil, safe bearing
capacity of soil, Function and requirements of
good foundation , types of foundation ,
introduction to spread, combined , strap, mat and
pile foundation
Masonry:
Definition and terms used in masonry. Brick
masonry, characteristics and requirements of
good brick masonry, Bonds in brick work, Header,
Stretcher, English, Flemish bond,
Stone masonry, Requirements of good stone
masonry, Classification, characteristics of
different stone masonry, Joints in stone masonry.
Types of walls; load bearing, partition walls,
cavitywalls
Module -3
Lintels and Arches: 10 hours L3
Definition, function and classification of lintels,
Balconies, chejja and canopy. Arches; Elements
and Stability of an Arch.
Floors and roofs:
Floors; Requirement of good floor, Components of
ground floor, Selection of flooring material, Laying
of Concrete, Mosaic, Marble, Granite, Tile flooring,
Cladding of tiles.
Roof;-Requirement of good roof, Types of roof,
Elements of a pitched roof, Trussed roof, King
post Truss, Queen Post Truss, Steel Truss,
Different roofing materials, R.C.C.Roof.
Module -4:
Doors, Windows and Ventilators: 10 Hours L2 L3 L5
Location of doors and windows, technical terms,
Materials for doors and windows, Paneled door,
Flush door, Collapsible door, Rolling shutter, PVC
Door, Paneled and glazed Window, Bay Window,
French window. Ventilators.
Sizes as per IS recommendations
Stairs: Definitions, technical terms and types of
stairs, Requirements of good stairs. Geometrical
design of RCC doglegged and open-well stairs.
Formwork: Introduction to form work,
scaffolding, shoring, under pinning.
Module -5
Plastering and Pointing : purpose, materials and 10 Hours L4 L5
methods of plastering and pointing, defects in
plastering-Stucco plastering, lathe plastering
Damp proofing- causes, effects and methods.
Paints- Purpose, types, ingredients and defects,

16
Preparation and applications of paints to new and
old plastered surfaces, wooden and steel surfaces.

Course outcomes:
After a successful completion of the course, the student will be able to:
1. Select suitable materials for buildings and adopt suitable construction
techniques.
2. Adopt suitable repair and maintenance work to enhance durability of
buildings.
Program Objectives (as per NBA)
o Engineering Knowledge.
o Problem Analysis.
o Interpretation of data.
Question paper pattern:
The question paper will have Ten questions, each full question carrying 16
marks.
There will be two full questions (with a maximum Three sub divisions, if
necessary) from each module.
Each full question shall cover the topics under a module.
The students shall answer Five full questions selecting one full question from
each module.
If more than one question is answered in modules, best answer will be
considered for the award of marks limiting one full question answer in each
module.
Text Books:
1. Sushil Kumar Building Materials and construction, 20th edition, reprint
2015, Standard Publishers
2. Dr. B.C.Punmia, Ashok kumar Jain, Arun Kumar Jain, Building
Construction, Laxmi Publications (P) ltd., New Delhi.
3. Rangawala S. C. Engineering Materials, Charter Publishing House, Anand,
India.
Reference Books:
1. S.K.Duggal, Building Materials, (Fourth Edition)New Age International (P)
Limited, 2016
2. National Building Code(NBC) of India
3. P C Vergese, Buliding Materials, PHI Learning Pvt. Ltd
4. Building Materials and Components, CBRI, 1990, India
5. Jagadish.K.S, Alternative Building Materials Technology, New Age
International, 2007.
6. M. S. Shetty, Concrete Technology, S. Chand & Co. New Delhi.

17
 Course Title: MATERIALS TESTING LABORATORY
[As per Choice Based Credit System (CBCS) scheme]
SEMESTER III
Subject Code 15CVL37 IA Marks 20
Number of Lecture Hours/Week 03 Exam Marks 80
Total Number of Lecture Hours 42 Exam Hours 03
CREDITS 02
Course objectives:
The objectives of this course is to make students to learn:
Ability to apply knowledge of mathematics and engineering in calculating the
1.
mechanical properties of structural materials.
2. Ability to function on multi-disciplinary teams in the area of materials
testing.
3. Ability to use the techniques, skills and modern engineering tools necessary
for engineering.
4. Understanding of professional and ethical responsibility in the areas of
material testing.
5. 5. Ability to communicate effectively the mechanical properties of materials.
Revised
Modules Teaching Blooms
Hours Taxonomy
(RBT) Level
1. Tension test on mild steel and HYSD bars. 03 Hours L2, L3, L5
2. Compression test on mild steel, cast iron and 03 Hours L1, L2, L3, L5
wood.
3. Torsion test on mild steel circular sections. 03 Hours L1, L2, L3, L5
4. Bending Test on Wood Under two point loading 03 Hours L1, L2, L3, L5
5. Shear Test on Mild steel- single and double shear 03 Hours L1, L2, L3, L5
6. Impact test on Mild Steel (Charpy & Izod) 03 Hours L1, L2, L3, L5
7. Hardness tests on ferrous and non-ferrous metals 06 Hours L1, L2, L3, L5
Brinells, Rockwell and Vickers
8. Tests on Bricks and Tiles 03 Hours L1, L2, L3, L5
9. Tests on Fine aggregates Moisture content, 06 Hours L1, L2, L3, L5
Specific gravity, Bulk density, Sieve analysis and
Bulking
10. Tests on Coarse aggregates Absorption, 06 Hours L1, L2, L3, L5
Moisture content, specific gravity, Bulk density
and Sieve analysis
11. Demonstration of Strain gauges and Strain 03 Hours L1, L2, L3, L5
indicators
NOTE: All tests to be carried out as per relevant latest
BIS Codes

18
Course outcomes:
After successful completion of the course, the students will be able to:
1. Reproduce the basic knowledge of mathematics and engineering in finding the
strength in tension, compression, shear and torsion.
2. Identify, formulate and solve engineering problems of structural elements
subjected to flexure.
3. Evaluate the impact of engineering solutions on the society and also will be
aware of contemporary issues regarding failure of structures due to unsuitable
materials.
Program Objectives (as per NBA)
1. Engineering Knowledge.
2. Evaluation of mechanical properties of structural materials.
3. Interpretation of test results.
Question paper pattern:
Group experiments - Tension test, compression test, torsion test and bending
test.
Individual Experiments - Remaining tests.
Two questions are to be set - One from group experiments and the other as
individual experiment.
Instructions as printed on the cover page of answer script for split up of marks
to be strictly followed.
All exercises are to be included for practical examination.
Reference Books:
1. Davis, Troxell and Hawk, Testing of Engineering Materials, International
Student Edition McGraw Hill Book Co. New Delhi.
2. M L Gambhir and Neha Jamwal, Building and construction materials-
Testing and quality control, McGraw Hill education(India)Pvt. Ltd., 2014
3. Fenner, Mechanical Testing of Materials, George Newnes Ltd. London.
4. Holes K A, Experimental Strength of Materials, English Universities Press Ltd.
London.
5. Suryanarayana A K, Testing of Metallic Materials, Prentice Hall of India Pvt.
Ltd. New Delhi.
6. Kukreja C B, Kishore K. and Ravi Chawla Material Testing Laboratory Manual,
Standard Publishers & Distributors 1996.
7. Relevant IS Codes

19
 Course Title: BASIC SURVEYING PRACTICE
[As per Choice Based Credit System (CBCS) scheme]
SEMESTER III
Subject Code 15CVL38 IA Marks 20
Number of Lecture Hours/Week 03 Exam Marks 80
Total Number of Lecture Hours 42 Exam Hours 03
CREDITS 02
Course objectives: This course will enable students to
The objectives of this course is to make students to learn:
1. Apply the basic principles of engineering surveying and measurements
2. Follow effectively field procedures required for a professional surveyor
3. Use techniques, skills and conventional surveying instruments necessary for
engineering practice..
Revised
Modules Teaching Blooms
Hours Taxonomy
(RBT)
Level
1. a) Measurements of distances using tape along with 03 L3, L4
horizontal planes and slopes, direct ranging.
b) Setting out perpendiculars. Use of cross staff,
optical square.
2. Obstacles in chaining and ranging Chaining but not 03 L3
ranging, ranging but not chaining, both ranging and
chaining.
3. Measurements of bearings / directions using prismatic 03 L3
compass, setting of geometrical figures using prismatic
compass.
4. Measurement of bearings of sides of a closed traverse 03 L3
and adjustment of closing error by Bowditch method.
5. Determination of distance between two inaccessible 03 L4
points using compass and accessories
6. Determination of reduced levels of points using dumpy 03 L4
level/auto level (simple leveling)
7. Determination of reduced levels of points using dumpy 03 L4
level/auto level (differential leveling and inverted
leveling)
8. To determine the difference in elevation between two 03 L4
points using Reciprocal leveling and to determine the
collimation error
9. To conduct profile leveling, cross sectioning and block 03 L3
leveling. Plotting profile and cross sectioning in excel.
Block contour on graph paper to scale
10. Measurement of horizontal angle by repetition and 03 L4
reiteration methods and Measurement of vertical
angles using theodolite.

20
11. Determination of horizontal distance and vertical 03 L4
height to a base inaccessible object using theodolite by
single plane and double plane method.
12. To determine distance and elevation using 03 L3
tachometric surveying with horizontal and inclined
line of sight.
13. Closed traverse surveying using Theodolite and 03 L3
applying corrections for error of closure by transit
rule.
14. Demonstration of Minor instruments like 03 L3
Clinometer, Ceylon Ghat tracer, Box sextant, Hand
level, Planimeter, nautical sextant and Pentagraph.
Course outcomes:
After a successful completion of the course, the student will be able to:
1. Apply the basic principles of engineering surveying and for linear and angular
measurements.
2. comprehend effectively field procedures required for a professional surveyor.
3. Use techniques, skills and conventional surveying instruments necessary for
engineering practice.[L3,L4][PO5]
Program Objectives (as per NBA)
1. Engineering Knowledge.
2. Problem Analysis.
3. Interpretation of data.
Question paper pattern:
All are individual experiments.
Instructions as printed on the cover page of answer script for split up of marks
to be strictly followed.
All exercises are to be included for practical examination.
Text Books:
1. B.C. Punmia, Surveying Vol.1, Laxmi Publications pvt. Ltd., New Delhi
2009.
2. Kanetkar T P and S V Kulkarni , Surveying and Levelling Part I, Pune
VidyarthiGrihaPrakashan, 1988
Reference Books:
1. S.K. Duggal, Surveying Vol.1, Tata McGraw Hill Publishing Co. Ltd. New
Delhi. 2009.
2. K.R. Arora, Surveying Vol. 1 Standard Book House, New Delhi. 2010

21