JOB NO. ITEM NO.

PURCHASE ORDER NO.

SPECIFICATION NO.
RECIPROCATING PUMP (API 674-2ND) REVISION NO. DATE
DATA SHEET PAGE 1 OF 5 BY
SI UNITS
1 APPLICABLE TO: PROPOSAL PURCHASE AS BUILT
2 FOR UNIT
3 SITE NO. OF PUMPS REQUIRED
4 SERVICE SIZE AND TYPE
5 MANUFACTURER SERIAL NO.

6 NOTE: INDICATES INFORMATION TO BE COMPLETED BY PURCHASER BY MANUFACTURER

7 GENERAL
8 NO. MOTOR DRIVEN OTHER DRIVER TYPE
9 PUMP ITEM NO'S PUMP ITEM NO'S
10 MOTOR ITEM NO'S DRIVER ITEM NO'S GEAR ITEM NO'S
11 MOTOR PROVIDED BY DRIVER PROVIDED BY GEAR PROVIDED BY
12 MOTOR MOUNTED BY DRIVER MOUNTED BY GEAR MOUNTED BY
13 MOTOR DATA SHEET NO. DRIVER DATA SHEET NO. GEAR DATA SHEET NO.

14 OPERATING CONDITIONS LIQUID

15 CAPACITY @ PT (m/h): TYPE OR NAME OF LIQUID
16 @ MAXIMUN VISCOSITY @ MINIMUM VISCOSITY PUMPING TEMPERATURE (C): COMPRESSIBILITY
17 DISCHARGE PRESSURE (kPa)(BARG): NORMAL MAXIMUM MINIMUM
18 MAXIMUM MINIMUM SPECIFIC GRAVITY MAXIMUM
19 SUCTION PRESSURE (kPa)(BARG): SPECIFIC HEAT Cp (kJ/kg
20 MAXIMUM MINIMUM VISCOSITY (cp) MINIMUM
21 DIFFERENTIAL PRESSURE (kPa)(BARG): CORROSIVE/EROSIVE AGENTS
22 MAXIMUM MINIMUM CHLORIDE CONCENTRATION (PPM)
23 NPSH AVAILABLE (m) WITHOUT ACCELERATION HEAD H2S CONCENTRATION (PPM)

24 ACCELERATION HEAD (APP G) NET LIQUID TOXIC FLAMMABLE OTHER

25 PERFORMANCE SITE AND UTILITY DATA

26 RATED CAPACITY (m/h) LOCATION INDOOR
27 NPSH REQUIRED (m) HEATED UNHEATED
28 PISTON SPEED (m/h) ELECTRICAL AREA CLASS GROUP
29 DISPLACEMENT (m/h) WINTERIZATION REQ'D TROPICALIZATION R
30 VOLUMETRIC EFFICIENCY (%) SITE DATA
31 MECHANICAL EFFICIENCY(%) RANGE OF AMBIENT TEMPS: MIN/MAX
32 kW @ MAXIMUM VISCOSITY UNUSUAL CONDITIONS
33 kW @ RELIEF VALVE SETTING DUST FUMES SALT ATMOSPHERE
34 MAXIMUM ALLOWABLE SPEED (RPM) OTHER
35 MINIMUM ALLOWABLE SPEED (RPM) UTILITY CONDITIONS
36 PINION SHAFT (RPM) ELECTRICITY DRIVERS HEATING CONTROL
37 HYDRAULIC kW BRAKE kW VOLTAGE
38 FOR DIRECT-ACTING PUMPS: HERTZ
39 DRIVE GAS PHASE
40 GOVERNOR TYPE COOLING WATER INLET RETURN DESIGN
41 INLET PRESSURE (kPa)(BARG) TEMPF MAX
42 INLET TEMPERATURE (C) PRESS.(kPa)(BARG) MIN
43 EXHAUST PRESSURE (kPa)(BARG) SOURCE
44 STALL PRESSURE (kPa)(BARG) INSTRUMENT AIR MAX
45 GAS CONSUMPTION (kg/kW-h) PRESSURE (kPa)(BARG)

46 APPLICABLE SPECIFICATIONS
47 API 674 POSITIVE DISPLACEMENT PUMPS-RECIPROCATING
48 GOVERNING SPECIFICATION (IF DIFFERENT)
49 REMARKS:
50
51

06/95 SHT 1 OF 5 API674SI.XLS REV 0

 JOB NO. ITEM NO.
RECIPROCATING PUMP (API 674-2ND) REVISION NO. DATE
DATA SHEET PAGE 2 OF 5 BY
SI UNITS
1 CONSTRUCTION
2 ANSI
3 LIQUID END: (2.7.1.1 THROUGH 2.7.1.4) NOZZLES SIZE RATING FACING
4 SIMPLEX MULTIPLEX PLUNGER LIQUID SUCTION
5 DUPLEX NO. OF CYLINDERS PISTON LIQUID DISCHARGE
6 SINGLE ACTING HORIZONTAL REMOVABLE LINERS GAS INLET
7 DOUBLE ACTING VERTICAL NO LINERS GAS EXHAUST
8 VALVES PER CORNER: GLAND FLUSH
9 NUMBER AREA (mm) VELOCITY (m/h) DRAINS
10 SUCTION OTHER
11 DISCHARGE OTHER
12 VALVE TYPE: DISC WING 2'BLE PORTED BALL OTHER

13 MATERIALS
14 PART LIQUID END ASTM NO. GAS EN
15 CYLINDER
16 LINER
17 PISTON OR PLUNGER
18 PISTON RINGS
19 PISTON ROD
20 VALVES/VALVE SEATS
21 GLAND
22 THROAT BUSHING
23 PACKING
24 LANTERN RING
25 BOLTING
26 OTHER
27 OTHER

28 LIQUID END LUBRICATION PACKING

29 PACKING LUBE LIQUID END GAS END
30 FLUSH SOURCE NO. OF RINGS
31 LUBRICATOR MAKE SIZE OF RINGS
32 SIZE NO. OF FEEDS OTHER

33 PRESSURE RATINGS QA INSPECTION AND TEST

34 LIQUID GAS COMPLIANCE WITH INSPECTORS CHECK LIST
35 CYLINDER CYLINDER CERTIFICATION OF MATERIALS
36 MAXIMUM PRESSURE (kPa)(BARG) FINAL ASSEMBLY CLEARANCES
37 MAXIMUM TEMPERATURE (C) SURFACE AND SUBSURFACE EXAMINATIONS
38 HYDROSTATIC TEST PRESS. (kPa)(BARG) RADIOGRAPHY
39 OTHER ULTRASONIC

40 DRIVE MECHANISM MAGNETIC PARTICLE

41 DIRECT COUPLED V-BELT OR COG GEAR LIQUID PENETRANT
42 COUPLING MANUFACTURER CLEANLINESS PRIOR TO FINAL ASSEMBLY

43 SOLEPLATES BASEPLATE SKID HARDNESS OF PARTS, WELDS & HEAT AFFECTED ZONES
44 BY PUMP MANUFACTURER SUITABLE FOR EPOXY GROUT FURNISH PROCEDURES FOR OPTIONAL TESTS
45 EXTENDED FOR TESTS REQ'D W/T
46 SUBPLATES BY PUMP MANUFACTURER HYDROSTATIC X
47 DRAIN-RIM DRAIN-PAN PERFORMANCE
48 LEVELING PADS SUITABLE FOR COLUMN MOUNTING NPSH
49 OTHER
50 REMARKS:
51

06/95 SHT 2 OF 5 API674SI.XLS REV 0

 JOB NO. ITEM NO.
RECIPROCATING PUMP (API 674-2ND) REVISION NO. DATE
DATA SHEET PAGE 3 OF 5 BY
SI UNITS
1 POWER FRAME CONTROLS
2 MAXIMUM FRAME RATING: TYPE:
3 kW @ RPM MANUAL REMOTE
4 MAXIMUM PRESSURE RATING(kPa)(BARG) AUTOMATIC LOCAL
5 CRANKSHAFT MATERIAL CAPACITY CONTROL:
6 NO. OF MAIN BEARINGS FLOW BYPASS VARIABLE SPEED
7 TYPE OF MAIN BEARINGS ONLY ONLY
8 INTERNAL GEARS YES NO VENDOR FURNISHES CS GOVERNOR & VALVE
9 GEAR RATIO VENDOR TO FURNISH CONTROL PANEL
10 GEAR SERVICE FACTOR FREESTANDING ON UNIT OTHER
11 POWER END LUBRICATION: TACHOMETER REQUIRED TYPE

12 TYPE SPLASH POSITIVE PRESSURE GRAVITY OTHER PURCHASE REQUIREMENTS

13 OIL PUMP: NAMEPLATE UNITS U.S. CUSTOMARY
14 MAIN VENDOR REVIEW FURNISHED PROCESS PIPING
15 AUXILIARY
16 DRIVEN BY VENDOR REVIEW PIPING DRAWINGS
17 OIL FILTER: VENDOR FURNISHED PULSATION SUPPRESSION DEVICES
18 TYPE MAKE VENDOR FURNISHED RELIEF VALVE
19 FILTRATION SIZE MODEL INTERNAL EXTERNAL
20 OIL COOLER RELIEF VALVE SETTING (kPa)(BARG)
21 TYPE LIQUID-FILLED PRESSURE GAUGES REQUIRED
22 SIZE TECHNICAL DATA MANUAL REQUIRED

23 DRIVERS MAXIMUM SOUND PRESSURE LEVEL

24 MOTOR @ m dBA
25 MANUFACTURER OVERSIZE NOZZLE MATING PARTS BY VENDOR
26 TYPE QUENCH-TYPE GLANDS REQUIRED
27 FRAME NO. PROVIDE PACKING COLLECTION CHAMBER
28 CONSTANT SPEED PROVIDE LANTERN RING PURGE
29 VARIABLE SPEED SIZE
30 kW RPM OIL HEATER CONNECTION REQUIRED
31 VOLTS PHASE DISTANCE PIECE COVERS
32 HERTZ SERVICE FACTOR SAFETY LOUVERED
33 ENCLOSURE GUARDS WEATHER
34 COVERS
35 STEAM TURBINE ADDITIONAL OIL SYSTEM ITEMS
36 OTHER (SEE SEPARATE DATA SHEETS) FLOW PRESSURE

37 GEAR REDUCER INDICATOR GAUGES

38 REQUIRED STRAINER OTHER
39 MANUFACTURER
40 MODEL OIL HEATER REQUIRED
41 TYPE STEAM ELECTRIC
42 SERVICE FACTOR MECHANICAL LUBRICATION REQUIRED
43 RATING MINIMIM DESIGN METAL TEMPERATURE C

44 V-BELT OR CHAIN DRIVE GEARS COMPLY WITH API 613 API 677
45 REQUIRED API 671 COUPLINGS AND GAUGES REQUIRED
46 NO. OF BELTS PREPARATION FOR SHIPMENT
47 SIZE OF BELTS DOMESTIC EXPORT
48 CHAIN DETAILS OUTDOOR STORAGE MORE THAN 6 MONTHS
49 TOTALLY ENCLOSED GUARD WEIGHTS (kg)
50 SLIDE RAILS FOR ADJUSTMENT PUMP BASE GEAR
51
06/95 SHT 3 OF 5 API674SI.XLS REV 0
 JOB NO. ITEM NO.
RECIPROCATING PUMP (API 674-2ND) REVISION NO. DATE
DATA SHEET PAGE 4 OF 5 BY
SI UNITS
1 PULSATION SUPPRESSION DEVICES FOR RECIPROCATING PUMPS(CONTD) SERVICE
2 THESE SHEETS TO BE FILLED OUT FOR EACH SERVICE AND /OR STAGE STAGE NO.

3 APPLICABLE TO: PROPOSAL PURCHASE AS BUILT

4 FOR/USER
5 SITE/LOCATION AMBIENT TEMPERATURE MIN/MAX /
6 PUMP SERVICE NUMBER OF PUMPS
7 PUMP MFG. MODEL/TYPE
8 SUPPRESSOR MFG.
9 NOTE: Data Completed Purch. By Pump/Supp. Mfg. w/Proposal By Mfg(s) after order By Mfg(s)/Purchaser
10 GENRAL INFORMATION APPLICABLE TO ALL SUPPRESSORS
11
12 TOTAL NUMBER OF SERVICES AND /OR STAGES
13 AMSE CODE STAMP STATE/COUNTRY/PROVINCE OF CODE AND REGULATIONS AP
14 OTHER APPLICABLE PRESSURE VESSEL SPEC. OR CODE
15 RADIOGRAPHY (X-RAY OF WELDS): NONE SPOT 100% IMPACT TEST SPECIAL WELDING REQUIRE
16 SHOP INSPECTION OUTDOOR STORAGE OVER 6 MONTHS SPECIAL PAINT SPEC
17
18 DESIGN APPROACH: 1 W/SIMPLIFIED MANUAL ANALYSIS OF PIPING SYSTE
19 HYDROTEST WITNESS 2 ACOUSTIC SIMULATION STUDY
20 OBSERVE STUDY TO BE WITNESSED: YES
21
22 OPERATING AND SUPPRESSOR DESIGN DATA
23 PUMP DATA, THIS SERVICE OR STAGE ONLY NUMBER OF CYL. INTERNAL PASSAGES
24 NOTES:
25 BORE DIA mm STROKE mm RPM
26 PUMP VALVE DATA
27 TYPE LIFT mm WEIGHT
28 SPRING PRELOAD N SPRING RATE
29 FULL PROJECTED AREA EFF. FULL LIFT

30 LIQUID HANDLED -SEE DATA SHEET PG. 1 NORMAL OPERATING

31 CORR. PRESENT (DESCRIBE)
32 SPECIFIC GRAVITY
33 COMPRESSIBILITY%
34 OPERATION N PARALLEL W/

35 PUMP MANUFACTURER'S RATED CAPACITY GPM

36 LINE SIDE OPERATING PRESSURE INLET (kPa)(BARG) DISCHARGE

37 OPERATING TEMP WITHIN SUPRESSORS INLET C DISCHARGE
38 ALLOWABLE PRESSURE DROP THROUGH SUPPRESSORS P (kPa)(BAR) % P (kPa)(BAR

39 INLET SUPPRESSOR DISCHARGE S

40 COMBINATION INLET SUPP SEPARATOR/INTERNALS YS. NO / YS. NO /
41 NO. (QTY) OF INLET &DISCH. SUPP. PER STAGE
42 ALLOWABLE PEAK-PEAK PULSE @ LINE SIDE NOZZLE (kPa)(BARG) % (kPa)(BARG)
43 ALLOWABLE PEAK-PEAK PUSLE @ CYL FLANGE NOZZLE (kPa)(BARG) % (kPa)(BARG)
44 MIN. REQ'D WORKING PRESSURE & TEMPERATURE
45 NOTE: After design, the actual Mawp & temp are to be determined (kPa)(BARG) @ C (kPa)(BARG)
46 based on the weakest component and stamped on the vessel.
47 The actual Mawp is to be shown on pg. 5 line 11 and on the U1A
48 Forms.
49
50
51
06/95 SHT 4 OF 5 API674SI.XLS REV 0
 JOB NO. ITEM NO.
RECIPROCATING PUMP (API 674-2ND) REVISION NO. DATE
DATA SHEET PAGE 5 OF 5 BY
SI UNITS
1 PULSATION SUPPRESSION DEVICES FOR RECIPROCATING PUMPS (CONT'D) SERVICE
2 THESE SHEETS TO BE FILLED OUT FOR EACH SERVICE AND/OR STAGE STAGE NO.

3 CONSTRUCTION REQUIREMENTS & DATA INLET SUPPRESSOR DISCHARGE S

4 BASIC MATERIAL REQUIRED, CS, SS, ETC.
5 ACT.MAT.,ASTM OR SA DESIGNATION SHELL/HEAD /
6 SPECIAL HARDNESS LIMITATIONS Rc YES NO SHELL & HEADS WELDS SHELL & HEADS
7 CORROSION ALLOW. (mm) REQUIRED mm
8 WALL THICKNESS, (mm) SHELL/HEAD mm/ mm mm/
9 NOM. SHELL DIA x OVERALL LGTH. mm/VOL.m x mm/ m x mm/
10 PIPE OR ROLLED PLATE CONSTRUCTION PIPE ROLLED PLATE PIPE
11 ACT MAX ALLOW. WORKING PRESS AND TEMPERATURE (kPa)(BARG) @ C (kPa)(BARG) @
12 MAX EXPECTED PRESSURE DROP D P, (kPa)(BAR)% LINE PRESS DP (kPa)(BAR) / % DP (kPa)(BAR
13 WEIGHT, kg EACH kg
14 INSUL NUTS & ALLOW. FOR INSULATION REQUIRED YES NO YES
15 EXPECTED P-P PULSE @ LINE SIDE CYL FLG, % LINE PRESS
16 BASED ON FINAL SUPPRESSOR DESIGN %/ % %/
17
18 SUPPORTS, TYPE/QUANTITY
19 CONNECTION REQUIREMENTS & DATA
20 LINE SIDE FLANGE, SIZE RATING/FACING/TYPE
21 PUMP FLANGE(S),QTY: SIZE RATING/FACING/TYPE
22 FLANGE FINISH, SPECIAL (SPECIFY)
23 PER ASME 16.5
24 INSPECTION OPENINGS REQUIRED YES NO BLINDED YES
25 SPEC. QTY, SIZE, 6000 LB NPT CPLG, FLG TYPE & RATING
26 *QTY, SIZE, 6000 LB NPT CPLG, FLG TYPE & RATING
27 VENT CONNECTIONS REQUIRED YES NO YES
28 SPEC. QTY, SIZE, 6000 LB NPT CPLG, FLG TYPE & RATING
29 *QTY, SIZE, 6000 LB NPT CPLG, FLG TYPE & RATING
30 DRAIN CONNECTIONS REQUIRED YES NO YES
31 SPEC. QTY, SIZE, 6000 LB NPT CPLG, FLG TYPE & RATING
32 *QTY, SIZE, 6000 LB NPT CPLG, FLG TYPE & RATING
33 PRESSURE CONNECTIONS REQUIRED YES NO YES
34 SPEC. QTY, SIZE, 6000 LB NPT CPLG, FLG TYPE & RATING
35 *QTY, SIZE, 6000 LB NPT CPLG, FLG TYPE & RATING
36 TEMPERATURE CONNECTIONS REQUIRED YES NO YES
37 SPEC. QTY, SIZE, 6000 LB NPT CPLG, FLG TYPE & RATING
38 CYL NOZZLE MAIN BODY
39 *QTY, SIZE, 6000 LB NPT CPLG, FLG TYPE & RATING
40
41
42 OTHER DATA AND NOTES
43 PUMP MFG'S SUPP. OUTLINE OR DRAWING NO.
44 SUPPRESSOR MFG'S OUTLINE OR DRAWING NO.
45 NOTES* = AS BUILT
46
47
48
49
50
51
06/95 SHT 5 OF 5 API674SI.XLS REV 0
 GENERAL

GEAR DATA SHEET NO.

LIQUID

COMPRESSIBILITY %
MINIMUM
MINIMUM
Cp (kJ/kg C)
MAXIMUM

OTHER

SITE AND UTILITY DATA

OUTDOOR
UNDER ROOF
DIV
TROPICALIZATION REQ'D

/ C

SALT ATMOSPHERE

CONTROL SHUTDOWN

MAX D

MIN

APPLICABLE SPECIFICATIONS
CONSTRUCTION

FACING LOCATION

GAS END

VALVE ROD

QA INSPECTION AND TEST

HARDNESS OF PARTS, WELDS & HEAT AFFECTED ZONES

W/T OBS
 CONTROLS
SIGNAL:
PNEUMATIC
ELECTRONIC

COMBINATION

OTHER

OTHER PURCHASE REQUIREMENTS

SI

VENDOR FURNISHED PULSATION SUPPRESSION DEVICES

dBA

SOLID
COVERS

TEMPERATURE

GAUGES

API 677

PREPARATION FOR SHIPMENT

EXPORT BOXING

WEIGHTS (kg)
DRIVER
 C

By Mfg(s)/Purchaser as Applicable
FORMATION APPLICABLE TO ALL SUPPRESSORS

CODE AND REGULATIONS APPLY

SPECIAL WELDING REQUIREMENTS

1 W/SIMPLIFIED MANUAL ANALYSIS OF PIPING SYSTEM

NO

ERATING AND SUPPRESSOR DESIGN DATA

INTERNAL PASSAGES

RPM

g
LIFT AREA
EFF. FULL LIFT AREA

(kPa)(BARG)
C
(kPa)(BARG) %

DISCHARGE SUPPRESSOR
YES NO

(kPa)(BARG) %
(kPa)(BARG) %

@ C
 DISCHARGE SUPPRESSOR

/
SHELL & HEADS WELDS
mm
mm/ mm
mm/ m
ROLLED PLATE
(kPa)(BARG) @ C
(kPa)(BAR) / %
kg
NO

CONNECTION REQUIREMENTS & DATA

NO BLINDED

NO

NO

NO

NO

OTHER DATA AND NOTES