Scribd
Upload
275 views

Column Is800

This structural design calculation document contains calculations to check the safety and strength of beam number 27 in a frame located at position A between rows 1 and 2. The calculations show that the beam is safe under bending, axial compression, and their combined stresses based on its material properties, dimensions, and applied loads. Key parameters like permissible bending and axial stresses, and their calculated values are presented. The input data and stress check results indicate the beam is safe for the given load case of belt tension, dead, and live loads.

Uploaded by

rammohan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
275 views

Column Is800

This structural design calculation document contains calculations to check the safety and strength of beam number 27 in a frame located at position A between rows 1 and 2. The calculations show that the beam is safe under bending, axial compression, and their combined stresses based on its material properties, dimensions, and applied loads. Key parameters like permissible bending and axial stresses, and their calculated values are presented. The input data and stress check results indicate the beam is safe for the given load case of belt tension, dead, and live loads.

Uploaded by

rammohan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 4

SECTION : STRUCTURAL PROJECT : BSSL : J-26

DESIGN CALCULATION NO. COMPUTED : Prakash


WI NO. /ZONE / SEC. CODE/NO CHECKED :
MEC/Q269/02/SA/001 DATE :
SHEET ________ OF __________

Beam Nos 27 Frame No : at A Row No bet 1 and 2 Axis No


Members No : Load Case Belt Tension + DL + LL

Result:
Bf1 fac= 1344.087
y
fac,cal= 13.146
fbc= 1618.467
D1 fbc,cal= 40.875
x x
Area= 213.000
Lamda < 120 Safe in Buckling
Tf1 Safe in Bending
Safe in Axial Compression
Safe in Axial Compression & Bending
y
Stress factor= 0.035
Safe in Deflection

DESIGN PARAMETERS * Only for Major Contribution


Wind Load/Eq Load (Y/N)? Stress Factor*
Pac,cal= 2.80 T NO 1.00
Mz,cal= 1.71 T-m NO 1.00
Lx= 10.55 M
Ly= 0.25 M
Let fy= 250.00 Mpa
Let D= 600.00 mm
tw= 16.00 mm Area = 213.000
Tf= 25.00 mm Aw/Area = 0.413
Bf= 250.00 mm

INPUT DATA SUMMARY :--

Flanges Tf = 25.00 mm
Bf= 250.00 mm
Webs tw = 16.00 mm
d= 550.00 mm
Area= 213.00 cm2 xc = 30.00 cm
Ixx= 125503.65 cm 4
xt = 30.00 cm
Iyy= 6529.19 cm 4
Zxc = 4183.45 cm3
rx= 24.27 cm Zxt = 4183.45 cm3
ry= 5.54 cm
l-x= 43.46
l-y= 4.52
l max = 43.46 Lamda < 120 Safe in Buckling
d/tw= 34.38
T/t= 1.56
D/T= 24.00

file:///conversion/tmp/scratch/365022959.xlsx 09/07/2017
SECTION : STRUCTURAL PROJECT : BSSL : J-26
DESIGN CALCULATION NO. COMPUTED : Prakash
WI NO. /ZONE / SEC. CODE/NO CHECKED :
MEC/Q269/02/SA/001 DATE :
SHEET ________ OF __________

Beam Nos 27 Frame No : at A Row No bet 1 and 2 Axis No


Calculation of Permissible Bending Compressive Stress

fbc=0.66(fcb.fy/(fcbn + fyn)1/n where fy is yield strength and n=1.4 and


fcb=k1(X+k2Y)c2/c1 where
X=Y.sqrt{1+l/20(l.T/ry.D)2} & l=Ly
Y=26.5X10 /(l/ry) MPa
5 2

c1= 30.00
c2= 30.00
Value of k2 : as w = Iytf / ( Iytf + Iybf ) = 0.13
k2= 0.0 See Table 6.4
Value of k1 : as s = area of flanges at support/area of flanges at max.BMpt
No Curtailment s= 1.0
Refer Table 6.3
k1= 1.0
Y= 129708.67
X= 129823.64 MPA
fcb= 129823.64 MPA fy= 250.00 MPA
fbc= 1618.47 kg/cm

Calculation of Permissible Axial compressive Stresses


Refer Clause 5.1.1
fac=0.6[fcc.fyy/{fcc)n + (fy)n}1/n]
fcc=p2.E/l2 and n=1.4 E = 2.1 x 10 5 MPA
fcc= 1044.02 Mpa Lamda= 43.46
fy= 250.00 Mpa
fac= 1344.09 kg/cm
Checking of Combined Stresses:
fbc= 1618.47 kg/cm
fac= 1344.09 kg/cm
fbc,cal= 40.88 kg/cm Safe in Bending
fac,cal= 13.15 kg/cm Safe in Axial Compression
fac,cal/fac +
fbc,cal/fbc = 0.04 Safe in Axial Compression & Bending
B

2
/

file:///conversion/tmp/scratch/365022959.xlsx 09/07/2017
Kg/cm2
Kg/cm2
Kg/cm2
Kg/cm2
cm2

Compression & Bending

file:///conversion/tmp/scratch/365022959.xlsx 09/07/2017
file:///conversion/tmp/scratch/365022959.xlsx 09/07/2017

You might also like