KISSsoft Release 03/2017

List of Modules

NEW
HIGHLIGHTS
KISSsys reliability

Fast group-based modelling

Tooth root stress calculation with FEM

Rough sizing for shafts

Fine sizing for bearings

and much more

KISSsoft AG
Rosengartenstrasse 4
8608 Bubikon
Switzerland

T. +41 55 254 20 50
F. +41 55 254 20 51
[email protected]
www.KISSsoft.AG
Offer
The software KISSsoft has a modular structure: a variety of calculation modules are available. You can limit
the amount of modules to suit your requirements

Get to know
Our free 30 days test version enables you to evaluate and select the modules independently before
purchasing a license.

Table of Contents
Table of Contents ............................................................................................................................................ 2
Base packages ................................................................................................................................................ 4
Base packages individual ............................................................................................................................ 4
Base package gearbox ................................................................................................................................ 6
Base packages complete ............................................................................................................................ 6
System modules .............................................................................................................................................. 6
KISSsys ....................................................................................................................................................... 6
Gearbox configurations ............................................................................................................................... 6
KISSsys Web ............................................................................................................................................... 7
KISSsys Expert Modules ................................................................................................................................. 7
Extended development environment for KISSsys ....................................................................................... 7
Gearbox variant generator ........................................................................................................................... 7
KISSsys efficiency calculation ..................................................................................................................... 7
KISSsys modal analysis .............................................................................................................................. 8
KISSsys housing deformation ..................................................................................................................... 8
KISSsys Reliability NEW ............................................................................................................................. 8
KISSsys Export Interfaces .............................................................................................................................. 8
Expert Modules Gears .................................................................................................................................... 8
Cylindrical gears .......................................................................................................................................... 8
Configuration / Dimensioning ................................................................................................................... 8
Methods for strength calculation .............................................................................................................. 9
Calculation with load distribution ............................................................................................................ 10
Contact analysis package .......................................................................................................................... 11
Contact analysis package complete .......................................................................................................... 11
Master gears .............................................................................................................................................. 11
Gear pumps ............................................................................................................................................... 11
Bevel gears ................................................................................................................................................ 12
Worm gears (Globoid) ............................................................................................................................... 13
Crossed helical gears or worm gears (Cylindrical-Worm gear) ................................................................. 13
Face gears ................................................................................................................................................. 14
Non-circular gears ..................................................................................................................................... 14
Beveloid gears ........................................................................................................................................... 15
Tooth form calculation ............................................................................................................................... 15
Further gear specific modules ................................................................................................................... 15
Expert modules shafts and bearings ............................................................................................................. 16
Shafts.. ................................................................................................................................. 16
Further shaft-specific modules .................................................................................................................. 17
Bearings..................................................................................................................................................... 17
CAD Interfaces .......................................................................................................................................... 18
2D Export ................................................................................................................................................... 18

2 / 21
 3D Export ................................................................................................................................................... 18
COM Interfaces.......................................................................................................................................... 19
Languages .................................................................................................................................................... 19
Services ........................................................................................................................................................ 20
Customizing ............................................................................................................................................... 20
Engineering ............................................................................................................................................... 20
Training courses ........................................................................................................................................ 20
Conditions ..................................................................................................................................................... 21
Single user version .................................................................................................................................... 21
Multi-user network version ......................................................................................................................... 21
Software update contract ........................................................................................................................... 21
* Third party manufacturers ....................................................................................................................... 21
Universities ................................................................................................................................................ 21

3 / 21
Base packages
Base packages individual
Modules Description

ZPK Cylindrical gear package

Geometry, control measures (DIN 3960, DIN 3962, DIN 3963, DIN 58400)
Tolerances as specified in updated ISO 1328-1:2013
Reference Profiles acc. to JIS 1701-1 NEW
Calculation and presentation 2D and 3D of the tooth form for external and internal
toothing with tooth flank modification
Graphical display of specific sliding
One strength calculation for a cylindrical gear, either as specified in DIN 3990, ISO
6336, AGMA 2001, VDI 2545, VDI 2736 or GOST 21354-87
Tooth friction / power loss acc. to Niemann
Extended range for possible profile shift
Deep tooth form/short cut tooth form, tools
Grinding the tooth root
Flash temperature course
Scuffing according to DIN 3990 and ISO TR 13989
Micropitting according to ISO TR 15144-1:2014 (Method B)
Arc of circle and spline approximation for 2D export (requires CA1)
Extended 2D and 3D tooth form display
Animation of gears when meshing, simultaneous display of more than one
manufacturing step, measuring function in the graphics, function for saving data for
A B comparison,
tooth form and tool in normal section
Collision check, marking of contact point, marking of collision
Manufacturing drawings
Rights: Z01, Z02 (Z02a, Z13, Z14, Z14a, ZA22), Z05, Z5x, Z5i, Z5j, Z5k, Z19e, Z19m

WPK Shafts and bearing standard package

Calculation of deformations also for statically overdetermined systems / multiple
supports, and line loads, Input of linear bearing stiffness
Shaft rough sizing NEW
3D display of forces and diagrams of bending
pressure angle and transverse shear
Mirror shaft
Rolling bearing service life (ISO281, L10)
Bearing power loss
One shaft strength calculation, either as specified in DIN743, in FKM Guideline,
Hnchen&Decker, AGMA 6101-E08 or AGMA 6001-E08
Smith and Haigh diagram
Rights: W01, W01c, W03, W03a, W05, W06a (or W06b, W06c, W6d), W12, K07b

MPK Shaft-hub connections

Cylindrical interference fit
Conical interference fit
Keys and Woodruff key
Multi-Spline, Polygonal connection
Involute splined shaft according to DIN5480, ANSIB92, ISO4156, DIN5482,
AGMA 6123-B06, AGMA 6123-C16 NEW

4 / 21
 AGMA 6123 incl. calculation of axis misalignment and crowning and verification of
the of the rim fracture NEW
Flank form straight line according to DIN5481
Go and no-go gauges according to DIN 5480-15
Bolts and pins, welded, glued and soldered joints
Clamped connections according to Roloff/Matek, Snaprings
Rights: M01a, M01x, M01b, M01c, M02a, M02e, M02b, M02d, M02c, Z09, M03a,
M08, M09a, Z5n, M05

SPK Bolt calculation according to VDI 2230, Sheet 1, 2015 and Sheet 2, 2014
Single bolt with axial and shearing force
Cylindrical flange
General connections with user-defined screw configurations (Sheet 2)
Calculation according to input FEM results (Sheet 2)
Considers high and low temperatures, temperature differences
Rights: M04, M04a, M04b

APK Automotive
Friction clutches
Synchronization as specified by Borg/Warner
allows for the calculation of either time or force during gear shifting
Rights: A10, A20

FPK Springs
Tension springs, compression springs, disc springs, leg springs, torsion springs
Tolerance standards for wire diameter (DIN EN 10218:2012, DIN EN 10270-3:2012)
NEW Rights: F01, F02, F03, F04, F05

RPK V-belts, toothed belts, chain drives

Strength and dimensioning, roller diameter, distance between axes, number of
belts, with or without tensioning pulley
Rights: Z90, Z91, Z92

LPK Stress analysis with local stresses according to FKM Guideline

2012, 6th edition
Consideration of support effect, for fatigue and static load
For calculation of safety factor and service life on basis of an external FEM
calculation
Rights: K12

VPK Linear drive train and Spindles according to Roloff/Matek

Calculation of safeties against buckling, flank pressure and more, for the operation
modes tightening and loosening
Rights: K15

TPK Chain of tolerances

Maximum- minimum dimension analysis, statistical analysis, tolerances: ISO / own
input
Rights: K10

Hardness conversion
Hardness conversion according to DIN EN ISO 18265: 2014
from and to HB, HRC, HV, Rm, etc.
Rights: K09

HPK Hertzian pressure

Calculation of Hertzian pressure for rolls, balls and planes
Rights: K14

5 / 21
Base package gearbox
Modules Description

KPK-G ZPK, WPK, MPK, TPK, HPK, hardness conversion

Base packages complete

Modules Description

KPK ZPK, WPK, MPK, SPK, APK, FPK, RPK, LPK, TPK, HPK, VPK,
Hardness conversion

System modules
KISSsys
Modules Description

SYS KISSsys
Software extension for the calculation of complete systems with power transmission
calculation, administration of variants and integrated programming language
Group-based modeling with new assemblies (e.g. Wolfrom, Ravigneaux) NEW
Import of CAD data, collision check
Assistant for input of parallel shafts and planetary stages
Automated 3D modeling
Adding complete stages to an existing model
Damage calculation results displayed in tables
Template for taking help results into account (moment of inertia, etc.)
Call the planet carrier deformation calculation in KISSsys NEW
Includes GPK
The corresponding KISSsoft modules (min. WPK, ZPK) are needed
Rights: K11, K11a, K11c

Gearbox configurations
Modules Description

GPK Package for sizing and rating of complete gearboxes (bearings, shafts, gears)
based on KISSsys
One to five stage cylindrical gearbox
One to four stage bevel and cylindrical gear unit (requires at least ZC1)
One to four stage worm and cylindrical gear unit (requires at least ZD1)
One and two stage planetary gear unit (requires ZA1), also with coaxial shafts
(requires WA1)
Load spectra (requires ZZ1, WA8
The corresponding KISSsoft modules (min.WPK, ZPK) are needed
Expert modules KS1, KS2, KS3 and KS4 run also with GPK
Rights: K11, K11c

6 / 21
KISSsys Web
Modules Description

SYSweb Software platform with configurable web interface for accessing KISSsys models,
designed for easy gear unit sizing using only the principal data.
The corresponding KISSsoft modules (min. WPK, ZPK) are needed
The price excludes the necessary KISSsoft and KISSsys modules.
Services will be invoiced at cost.

KISSsys Expert Modules

Extended development environment for KISSsys
Modules Description

KSE Interface to Eclipse shareware

Development environment for KISSsys functions, including debugging and
breakpoints
Requires KISSsys
Rights: K11e

Gearbox variant generator

Modules Description

KS1 KISSsys model for the sizing of Gearbox variants

Automatically generates gear unit variants with different stages and transmission
ratios from the overall transmission ratio and the torque
Results are displayed in 3D
For cylindrical gear units with first stage as a cylindrical, bevel, worm or crossed
helical gear stage, and for planetary gear units
This function needs a KISSsys or GPK license and requires the appropriate
KISSsoft modules (min. WPK, ZPK)
Rights: K11f

KISSsys efficiency calculation

Modules Description

KS2 Calculation of efficiency and thermal power

Power losses can be changed by predefined factors.
Range of options for evaluating thermal power etc.
Transferring meshing losses from the contact analysis
Power loss and efficiency for plain bearings NEW
This function needs a KISSsys or GPK license and requires the appropriate
KISSsoft modules (min. WPK, ZPK)
Rights: K11h

7 / 21
KISSsys modal analysis, beta version in 03/2017
Modules Description

KS3 Calculation of the drive's Eigenfrequencies and vibration modes (shaft systems)
Three-gear chains, four-gear chains and planetary systems NEW
Takes the contact stiffness of the gears into account
Outputs of torsional and coupled (torsional, flexural and axial) vibrations
Vibration calculation with unbalance response and amplitude using speed
Calculation of the Campbell diagram for shaft systems
This function needs a KISSsys or GPK license and requires the appropriate
KISSsoft modules (min. WPK, ZPK)
Rights: K11i

KISSsys housing deformation

Modules Description

KS4 Calculation of housing deformation using the bearings reaction forces

Calculates and modifies the bearings offset and tilting
The housings stiffness matrix is used to perform the calculation. This matrix is
derived from an FE calculation (NEW ANSYS, ALTAIR OptiStruct. etc.)
This function needs a KISSsys or GPK license and requires the appropriate
KISSsoft modules (min. WPK, ZPK): Rights: K11j, K20a, K20b, K20c, K20d, K20e

KISSsys Reliability NEW

Modules Description

KLR Calculation and display according to Bernd Bertsche, with 3-parameter Weibull
NEW distribution. Results for gears (bending, pitting) are displayed in the reports, results
for roller bearings also in the graphics. Rights: K18

KISSsys Export Interfaces

Modules Description

KS10 MSC Adams Gear AT Integration

Export of KISSsys data into Gear AT. Exports data of the system, bearings, shafts,
connecting elements, loads, macro geometry of cylindrical gears.
Rights: K11k1, K11k

Expert Modules Gears

Cylindrical gears

Configuration / Dimensioning
Modules Description

ZA1 Planetary gear, Three gears, Four gears; Rights: Z01a, Z19g

ZA2 Rack; Rights: Z01b

8 / 21
ZA3 Rough sizing
Cylindrical gear pre-sizing (gear pairs, planetary trains)
Sizing acc. to required safeties, determination of the possible range for center
distance and tooth thickness for solutions with the same torque capacity, Display of
several suggestions with indication of the total weight;
Rights: Z03

ZA4 Fine sizing (macro geometry)

Gear pairs, planetary trains, gear chains
The optimization produces a list of all possible variants with various parameters;
varying of gear module, number of teeth, profile shift, pressure angle, helix angle,
center distance
Considers assembly conditions
For each solution, a separate strength calculation is performed
Automatic sizing of deep tooth form (requires module ZA5)
Calculation of transmission error for al variants (requires module ZA30)
Varying the reference profile
Individual definition of cutter and pinion type cutter list NEW
All feasible solutions regarding geometry are listed
All solutions are classified as to various criteria
Display of results in tables and graphics
Rights: Z04, Z04a

ZA33 Fine sizing (micro geometry) Profile and width modifications

ZA5 Geometry sizing functions and special calculations

Sizing of profile shift related to various criteria
Calculation of profile shift based on measured tooth geometry
Calculation of tooth thickness allowances based on measured tooth geometry
Pre-machining tools with grinding allowance, Topping tools
Sizing for tooth height regarding transverse contact ratio
Sizing of linear profile modification
Crowning and helix angle modification sized whilst taking into account axis
inclinations as specified in ISO 6336-1, Appendix E (requires ZA35)
Report for tolerances ISO 1328, DIN 3961, DIN 58405, BS 436, AGMA 2001,
AGMA 2015
Calculation with manufacturing profile shift
Sizing of center distance regarding balanced specific sliding
Sizing of helix angle regarding various criteria
Profile and tooth trace diagram (K diagrams)
Rights: Z01x, Z15, Z19a, Z19d, Z19f, Z19h, Z19l, Z19n

ZA6 Profile modifications with grinding worms and dressing wheels

NEW Checks whether a required tip relief can be generated with an available grinding
worm / dressing wheel
Includes the available grinding worms / dressing wheels from a user-defined file. It
Displays the suitable ginding worms / dressing wheels in a table and shows the
manufacturing tip relief for the current gear
Right: Z19j

Methods for strength calculation

Modules Description

ZA10 ISO 6336: 2006; Rights: Z02a

9 / 21
ZA11 DIN 3990: 1988; Rights: Z02

ZA12 AGMA 2001, AGMA 2101; Rights: Z13

ZA13 VDI 2737: Calculate the tooth root load capacity of internal teeth with the influence
of the rim thickness, draft edition 2016, Rights: Z23

ZA14 FVA (output of analogue results like Stplus)

Rights: Z10

ZA15 Graphical method for calculating the tooth root stress; Rights: Z19i

ZA16 AGMA 925: 2003, lubrication gap and flash temperature course according to AGMA
Rights: Z19k

ZA17 VDI 2545: 1988, for plastics, wear calculation with safety against shearing according
to Frstenberger, Rights: Z14

ZA18 Static strength (metal and plastic); Rights: Z02x

ZA19 BV-RINA for military vessels, RINA 2010 for commercial vessels, Lloyds Register:
2013, DNV41.2, (requires ZA10); Rights: Z02b, Z02d

ZA20 AGMA 6011, AGMA 6014, AGMA 6011-J14, AGMA 7004, API 613; Rights: Z13b

ZA21 VDI 2736: 2014, for plastics (Sheet 2), wear calculation with safety against shearing
according to Frstenberger, Rights: Z14a

ZA22 GOST 21354-87: 1987, including manufacturing tolerances and tooth thickness
allowances; Rights: Z02e

ZA23 ISO13691: 2001, for High speed, special purpose gear units.
Rights: Z02f

ZA24 Tooth root stresses with FEM

NEW Calculation of the tooth root stresses for cylindrical gears (with straight or helical
teeth) using 2D-FEM
Right: Z38

Calculation with load distribution

Modules Description

ZA30 Contact analysis for cylindrical gears, taking into account tooth profile and tooth
flank modifications, and shaft deformation
Flank fracture according to ISO/DTR 19042-1 (July 2016) (requires ZZ4)
Path of contact under load
Calculation and display of Hertzian pressure and tooth root stress along the actual
tooth flank
Calculation of tooth mesh stiffness and transmission error under load based on the
actual tooth form
Display of specific sliding, sliding velocity and sliding factors for gears under load
from actual tooth form
Display of friction loss and local heat generation along the meshing
Calculates wear for plastics (dry run) and steel (cold wear)
Calculation and display of progression of wear
Calculation of safety against micropitting according to ISO TR 15144,
Calculation of lubrication gap according to ISO 15144 and AGMA 925
with actual normal force
Rights: Z24, Z25, Z27, Z30, Z31, Z31a, Z32, Z36

10 / 21
ZA34 Contact analysis for planetary gears, taking into account tooth profile and tooth flank
modifications, and shaft deformation
Floating sun wheel
Flank fracture according to ISO/DTR 19042-1 (July 2016) (requires ZZ4)
All other functionalities as described in ZA30.
Rights: Z24, Z25, Z27, Z30, Z31, Z31a, Z34, Z36

ZA33 Optimization of tooth flank and tooth profile modifications

Optimized options for varying and combining data, for example, cross variations of
amounts and coefficients
All solutions are classified as to various criteria
Graphical display of the classification
Enhanced graphical representation according to the fine sizing method
(requires ZA30 or ZA34); Rights: Z33

ZA35 Load distribution coefficient KHbeta acc. to ISO 6336 Annex E

Gaping and load distribution with shaft deformation and for every variation of
tolerances with (+/-)fma and (+/-)fhb displayed as a graphics and listed in the report.
Also for individual planets
Rights: Z02c

ZA36 Planet carrier deformation, with open-source FE library Code_Aster for para-
metrized geometry, import of planet carrier data in STEP format
Import of calculation results from ABAQUS
(requires ZA35 or ZA34). Rights: Z37

Contact analysis package

Modules Description

KAP ZA30 and ZA34

Contact analysis package complete

Modules Description

KAPK ZA30, ZA33, ZA34, ZA35, ZA36

Master gears
Modules Description

ZA40 Master gears: Master gear analysis and check; Rights: Z29

Gear pumps
Modules Description

ZB1 Gear pumps, Basic calculation

Calculation of the transported volume of oil for gear pumps (without consideration
of any feed-back volume)
for internal and externally geared pumps
for both standard involute and non-involute profiles
can be combined with fine sizing
Rights: Z26

11 / 21
ZB2 Gear pumps, Enhanced calculation
Calculation and presentation of the pump characteristics during contact for detailed
analysis and optimization
Enclosed volume during mesh (feed-back volume), volume under critical in-flow
speed at the narrowest point in entry chamber, total volume under entry pressure,
torque on both gears (including option for calculation with or without Hertzian
Pressure consideration), sliding velocity, wear number
Alternatively, the Hertzian flattening due to tooth contact can be considered
Rights: Z26a, Z32

Bevel gears
Modules Description

ZC1 Bevel and hypoid gears geometry

Geometry according to DIN 3971 and ISO 23509
dimensions of bevel gears (measurements for manufacturing), for straight, helix-
and spiral bevel gears
Conventional production, Klingelnberg or Gleason
Conversion of Gleason bevel-gear geometry data to DIN 3971 and vice versa
Rough sizing
Graphics
2D tooth form geometry verification of the tooth form separately for inside and
outside (toe/heel)
Rights: Z07, Z07d, Z07m, Z7s1

ZC10 Generation of a 3D model for exporting straight and helical toothed bevel gears with
modifications (apexes not in one point), and spiral bevel gears with modifications,
for export. Load-free visual inspection of tooth contact by rotating either one, or both,
gears.
(requires CB1); Rights: Z07p

ZC2 Strength acc. to ISO 10300:2001 and ISO 10300:2014 Methods B and C
Rights: Z07e

ZC3 Strength according to DIN 3991; Rights: Z07g

ZC4 Strength according to AGMA 2003-B97 and AGMA 2003-C10; Rights: Z07j

ZC5 Strength calculation according to Klingelnberg KN3030 1.2 (Spiral bevel gear,
palloid and cyclo-palloid gears; Rights: Z07a

ZC6 Strength calculation according to Klingelnberg KN3030 1.2 (Hypoid gear, palloid
and cyclo-palloid gears); Rights: Z07b

ZC7 Strength according to VDI 2545 and Niemann; Rights: Z07h

ZC8 Static strength bevel gears / differentials; Rights: Z07i

ZC9 Strength acc. to ISO 10300:2014 Method B for hypoid gears; Rights: Z07f

ZC11 Strength acc. to DNV 41.2, root and flank strength, flank breaking, safety hardening
depth; Rights: Z07l

ZC12 Fine sizing for bevel, hypoid and differential bevel gears
Rights: Z07n

ZC13 Sizing of topological modifications

Only sold together with engineering services performed by KISSsoft AG

12 / 21
 Specific instructions on how to use this tool are supplied with this package
Rights: Z7s3

ZC30 Contact analysis under load

Takes microgeometry into account
Calculation of contact lines, transmission error and stress ratios
Calculation of wear
Flank fracture according to ISO/DTR 19042-1 (July 2016)
Calculation of the relative positions VHJ and axis angle errors directly from the shaft
deformation
(requires ZZ4)
Rights: Z24, Z25, Z27, Z35, Z36

ZC33 Modification sizing

NEW Optimization of tooth flank and tooth profile modifications
Optimized combinations and different variations (cross-variations of amounts and
coefficients, etc.) works also with topological modifications
Classification of all solutions relative to different criteria
Graphic display of classifications
Right: Z7o

Worm gears (Globoid)

Modules Description

ZD1 Worm gear geometry

Cylindrical Worms with enveloping worm wheels, geometry according to ISO14521
and DIN 3975
Control measures for worms (measurement over 3 pins) and worm wheels
(measurement over balls)
Worm sizing with tool module; Rights: Z08

ZD10 Generates a 3D model for export. Load-free visual inspection of tooth contact by
rotating either one, or both, gears
For flank forms ZA, ZI and ZN, ZC, ZK,
(requires CB1); Rights: Z08p

ZD2 Strength according to ISO 14521

Rights: Z08b

ZD3 Strength according to DIN 3996,

Rights: Z08a

ZD4 Strength according to AGMA 6034 and AGMA 6135

Rights: Z08c

ZD5 Fine sizing for worm gears,

Rights: Z08n

Crossed helical gears or worm gears (Cylindrical-Worm gear)

Modules Description

ZE1 Geometry of crossed helical gears

Calculation of crossed helical gear and worm (cylindrical worm and cylindrical worm
gear as e.g. usual in precisions mechanics)

13 / 21
 Control measures for worms (measurement over 3 pins) and worm wheels
(measurement over balls)
Collision check
Rights: Z17, Z5k

ZE2 Strength calculation on the basis of ISO6336/Niemann, method Hirn

Rights: Z17a

ZE3 Strength calculation for plastics on basis of VDI 2545/Niemann, Hoechst method,
wear calculation according to Pech
Rights: Z17b, Z17c, Z17f

ZE4 Static strength (bending and shearing) for metal and plastic
Rights: Z17d

ZE5 VDI 2736 for plastics (Sheet 3), wear calculation according to Pech
Rights: Z17e, Z17f

ZE6 Fine sizing for crossed helical gear

Rights: Z17n

Face gears
Modules Description

ZF1 Face gears geometry

Calculates the geometry of face gears coupled with cylindrical pinion gears
2D views with tooth form simultaneously on the inside, the center and on the outside
Checking undercut and pointed tooth tip is performed graphically in the 2D view,
while tooth addendum height can be varied to prevent pointed tooth tip (including
sizing function)
Sizing of optimal facewidth
Rights: Z06

ZF10 Generates a 3D model, with offset and any shaft angle, for export (requires CB1)
Load-free visual inspection of tooth contact by rotating either one, or both, gears.
Rights: Z06f

ZF2 Strength calculation on basis of ISO6336 and literature; Rights: Z06a

ZF3 Strength calculation on basis of CrownGear/DIN 3990; Rights: Z06b

ZF4 Strength on basis of ISO 10300, Method B; Rights: Z06c

ZF5 Strength on basis of DIN 3991, Method B; Rights: Z06d

ZF6 Static strength calculation; Rights: Z06e

Non-circular gears
Modules Description

ZG1 Calculation of non-circular gears

Only sold together with engineering services performed by KISSsoft AG.
Specific instructions on how to use this tool are supplied with this package.
Rights: Z40

14 / 21
Beveloid gears
Modules Description

ZH1 Beveloid geometry and strength (only for external toothing)

The strength calculation is covered by a cylindrical gear calculation strength
calculation
Profile and tooth trace modifications, e.g. negative crowning etc.
Graphical contact analysis
Rights: Z50

ZH10 Generate 3D model for export

(requires CB1); Rights: Z50p

Tooth form calculation

Modules Description

ZY1 Extended 2D and 3D tooth form display Included in

Animation of gears when meshing, simultaneous display of more than one ZPK
manufacturing step
Measuring function in the graphics, function for saving data for A B comparison
Tooth form and tool in normal section
Collision check, marking of contact point, marking of collision
Rights: Z05x, Z05j, Z05k

ZY2 Import of tooth form or tool geometry

Import of any kind of non-involute tooth shapes or tools (e.g. from CAD or 3D-
application, DXF or VDA); Rights: Z05a

ZY3 Calculation of milling cutter (hob) and pinion type cutter

Calculation of reference profile and pinion type cutter (also for the design of special
tools); Rights: Z05c

ZY4 Calculation of counter gear by generating

Rights: Z05d

ZY5 Addition for moulding

Compensation of shrinking, spark gap, modification of pinion type cutter
Rights: Z05e

ZY6 Progressive Profile corrections, arc-like running in curve,

Elliptical root radius; Rights: Z05f, Z05g

ZY7 Cycloid- and arc of circle tooth forms

Designed Involute
Straight flank; Rights: Z05h, Z05n

ZY8 Tool scaling

Scaling the DXF tool or tooth form with the gear's normal module. Rights: Z05q

Further gear specific modules

Modules Description

ZZ1 Load spectra, service life, transmissible torque/power

Calculation of transmissible power with and without load spectra
Calculation of service life with and without load spectra

15 / 21
 Calculation of safeties with load spectra (for cylindrical, bevel, and cross helical
gears)
Taking into account the direction of rotation and load of the individual stages (for
cylindrical gears)
Rights: Z16, Z16a, Z18, Z18a

ZZ2 Hardening depth

Proposal of required hardening depth based on Hertzian pressure (for cylindrical
gears, bevel gears); Rights: Z22

ZZ3 Backlash
Calculation of acceptance-backlash and operating-backlash
Taking into account tooth and shaft bending (requires ZA35)
(for cylindrical-, crossed helical- and worm gears); Rights: Z12

ZZ4 Tooth flank fracture calculation for bevel gears and cylindrical gears according to
Dr. Annast, TU Mnchen, 2002 and ISO/DTR19042 (draft); Rights: Z07k

ZZ5 Measurement grid points for measuring topology, flank and root, for cylindrical,
bevel and spiral-toothed gears, and for splines
For measurement machines: Klingelnberg and Gleason (requires CB1); Rights:
Z05o

ZZ6 Plastics Manager

NEW Easy way to generate plastics material files (DAT files) based on the material
properties and measured test bench data according to VDI 2736-4 (needs the ZA21
or ZE5 module)
Save the new materials directly to the KISSsoft database
Right: K17

Expert modules shafts and bearings

Shafts
Modules Description

WA1 System of shafts composed of various coaxial shafts

Calculation of the deformation in the shaft system
Taking into account the bearing offset, bearing clearance, thermal expansion, linked
shafts, nonlinear bearing stiffness calculated from the internal geometry
Rights: W01a, W01b, W03b, W03c, W03d

WA2 Tooth trace modification

Calculation of longitudinal deformation
Load distribution with and without modification
Sizing of the optimal tooth trace modification
Takes gear body deformation into account
Implementation of the displacement matrix from the gear body deformation
calculated in DPK (DPK see page 17)
Rights: W10

WA3 Buckling (for beams and shafts)

Rights: W13

WA4 Critical speeds and frequencies

Torsions-, bending-, longitudinal frequencies

16 / 21
 Campbell diagram
Rights: W04, W04x

WA5 Strength calculation according to Hnchen & Decker

Shaft design regarding constant equivalent stress and maximal deformation
Rights: W06a, W12

WA6 Strength calculation acc. to DIN 743, 2012 edition

Shaft design regarding constant equivalent stress and maximal deformation; Rights:
W06b, W12

WA7 Strength calculation acc. to FKM, 2012 edition

Shaft design regarding constant equivalent stress and maximal deformation
Endurance limit calculation for surface treated parts according to section 5.5
Options for coefficient Kf according to sections 4.3.2 and 4.3.3, determining of the
core hardness from the tensile strength Rm NEW
Rights: W06c, W12

WA10 Strength calculation based on AGMA 6101-E08 and AGMA 6001-E08

Rights: W06c, W12

WA8 Load spectra for shafts and bearings

Calculation for shaft limited life- and endurance strength
Bearing calculation with load spectra. Setting of separate temperatures for each
load bin with consideration in the calculation of bearing clearance and lifetime
according to ISO/TS 16281 NEW
Rights: W01s, W06s

WA11 Forced vibration

NEW Vibration on the shaft calculated on basis of the unbalance response.
Right: W14

Further shaft-specific modules

Modules Description

DPK Gear body deformation

For asymmetric gear bodies, the resilience of the gear body is calculated using the
integrated FE Software Code Aster (flexibility of gear rims and webs in axial plane).
Precise determination of the gear flank misalignment. Display of the results of the
deformation calculation in the software Salome. Output of the stiffness matrix. Also
for internal toothing. Rights: K16

Bearings
Modules Description

WB1 Enhanced bearing calculation (L10m, Lnm)

Influence of lubrication according to ISO281-1
Thermally permissible service speed acc. DIN732
Definition of the impurity for each rolling bearing individually NEW
Rights: W05a

WB2 Reference service life calculation according to ISO 16281 (L10r or Lnmr if combined
with Module WB1)
Diagram of the load distribution in the bearing
Diagram of the load distribution over the rolling bodies and races

17 / 21
 User specified input of roller profiles
Works for thrust needle roller bearings NEW
Graphic showing stresses under the contact surface NEW
Rights: W05b, W05c (Requires WA1)

WB3 Plain hydrodynamic bearings

Hydrodynamic radial plain bearings: Oil or grease lubricated, according to DIN
31657, DIN 31652 NEW and Niemann
Hydrodynamic axial plain bearings: Calculation of pad thrust bearings, tilting-pad
thrust bearings, according to ISO 12130
Rights: W07, W07a, W07b, W07c, W7d, W7e, W08

WB4 Calculation of a single bearing with internal geometry according to ISO16281

Own input of the inner and outer ring deformation (possible without the WPK)
User specified input of roller profiles
Deformation of bearing rings through external load NEW
Input loads from the planetary stage calculation NEW
Tilting of elastic bearing rings is taken into account NEW
Rights: W51

WB5 Rolling bearing fine sizing

NEW Optimization of the internal geometry of bearings through variation calculation
Variants are displayed in a list, or graphically (needs the WB4 module)
Right: W51a

CAD Interfaces
2D Export
Modules Description

CA1 2D DXF and IGES Export; Rights: K05a, K05e

3D Export
Modules Description

CB1 STEP and Parasolid format export in 3D through Parasolid kernel

Display and export cylindrical gears with modifications, and straight and helical
toothed bevel gears (apexes in one point, without modifications), beveloid gears,
display as skin model for checking tooth contact, spline (shaft-hub), shafts, rack
Rights: K05u

CB2 Integration with Solid Edge: Generation of 3D gears (cylindrical gears, worms,
crossed helical gears, straight bevel gears, splines (shaft-hub), shafts and racks)
directly from the calculation, using the KISSsoft menu in Solid Edge, includes CC1;
Rights: K05d, K4

CB3 Integration with SolidWorks: Generation of 3D gears (cylindrical gears, worms,

crossed helical gears, straight bevel gears, splines (shaft-hub), shafts and racks)
directly from the calculation, using the KISSsoft menu in SolidWorks, includes CC1;
Rights: K05k, K4

CB4 Integration with Inventor: Generation of 3D gears (cylindrical gears, worms, crossed
helical gears, straight bevel gears, splines (shaft-hub), shafts and racks) directly

18 / 21
 from the calculation, using the KISSsoft menu in Inventor, includes CC1; Rights:
K05m, K4

CB5 Integration with CATIA V5: Generation of 3D gears (cylindrical gears, worms,
crossed helical gears, straight bevel gears, splines (shaft-hub)) (manufacturer:
SWMS); Rights: K05o*

CB6 Integration with Creo Parametric: Generation of 3D gears (cylindrical gears, worms,
crossed helical gears, straight bevel gears, splines (shaft-hub)) beinhaltet CC1,
(manufacturer: Applisoft); Rights: K05q*, K4

CB7 Integration with Siemens NX: Generation of 3D gears (cylindrical gears, worms,
crossed helical gears, straight bevel gears, splines (shaft-hub), shafts and racks)
directly from the calculation, using the KISSsoft menu in NX, includes CC1; Rights:
K05n, K4

*) please refer to the conditions

COM Interfaces
Modules Description

CC1 COM interface, basic

Calls basic KISSsoft functions, such as report creation, CalculateRetVal, and
KsoftVersion, via the COM interface.
On request, can also display KISSsoft messages.
Rights: K04

CC2 COM interface, expert (includes CC1)

Most of the sizing and optimization functions are provided by the extended COM
interface, which is accessed using CallFunc and CallFuncNParam. Contact analysis
can now be completely controlled via the COM interface.
Rights: K04, K04a

Languages
Modules Description

LA1 German: Software user interface, reports, graphics, messages included

LA2 English: Software user interface, reports, graphics, messages; Rights: K02a

LA3 French: Software user interface, reports, graphics, messages; Rights: K02b

LA4 Italian: Software user interface, reports, graphics, messages; Rights: K02c

LA5 Spanish: Software user interface, reports, graphics, messages; Rights: K02d

LA6 Russian: Software user interface, reports, graphics, messages; Rights: K02e

LA7 Portuguese: Software user interface, reports, graphics, messages; Rights: K02f

19 / 21
Services
Customizing
We can tailor our software to suit our customers' requirements. If you can't find the functionality you require
in the list, please contact us directly. Our team of experts will then work together with you to develop your
own specialized solutions.

Engineering
KISSsoft AG also provides engineering and consultancy services. Our expertise and experience has been
gathered over many years, working on a multitude of different projects in a wide range of industries. We would
also be delighted to make you a specific offer.

Training courses
Our training courses teach you how to make best possible use of our software and explain the most important
theories that lie behind it. You will find more information about public training courses, and also the registration
forms, on our website.
Please contact us directly if you would like information about company-specific training courses.

20 / 21
Conditions
Single user version
The single-user installation of KISSsoft is licensed with a USB dongle. The calculation program can be
installed on various computers, but calculations can only be executed with dongle in the USB port.

Multi-user network version

We offer network installation for any number of users, whereas the number of simultaneous users is restricted
to the number of purchased licenses. The license is restricted to one site (physical address).

Software update contract

The software maintenance and update contract guaranties continuous long term use of KISSsoft. It offers the
following benefits Technical support on the calculation methods, software usage support, updates of software,
adaptations to new standards and full compatibility with new operation systems at a cycle of one update a
year, patches, and some additional features. Copy of contract on request.

* Third party manufacturers

* = Software developed by one of our partners. The modules marked with * may have different conditions.
Details on request.

Universities
Special conditions for universities apply. Please refer to our website for more information.

KISSsoft AG
Rosengartenstrasse 4
8608 Bubikon
Switzerland

T. +41 55 254 20 50
F. +41 55 254 20 51
[email protected]
www.KISSsoft.AG

21 / 21