Schedule of Rates Example
Uploaded by
MarvvvSchedule of Rates Example
Uploaded by
MarvvvSCHEDULE OF RATES
FOR
TERM CONTRACTS
FOR
BUILDING WORKS
2013 EDITION
Volume 1
(Builders Works)
ARCHITECTURAL SERVICES DEPARTMENT
HONG KONG
ARCHITECTURAL SERVICES DEPARTMENT
HONG KONG
October 2013
DISCLAIMER
This Schedule of Rates is solely compiled as a basis for tendering of Term Contracts for which the
Architectural Services Department is responsible. The Schedule rates may not necessarily reflect the
market values of materials / products / works as included in this Schedule.
There are no representations, either expressed or implied, as to the suitability of this Schedule for purposes
other than that stated above, and the Architectural Services Department does not accept any liability
and responsibility for any special, indirect or consequential loss or damages whatsoever arising out of
or in connection with the use of this Schedule or reliance placed on it.
Users who choose to adopt this Schedule for other purposes are responsible for making their own
assessments and judgment of all information contained herein, and they shall acknowledge and shall
deem to have acknowledged any risks and consequences resulted from such use.
VOLUME 1
CONTENTS
Items Pages
Section 00 General Regulations .................................................................................................................................... 00/1 - 00/19
Section 01 Contract Facilities and Special Attendances................................................... 01001 - 01017 ............... 01/1 - 01/9
Section 02 Demolition..................................................................................................... 02001 - 02033 ............... 02/1 - 02/8
Section 03 Excavation..................................................................................................... 03001 - 03063 ............... 03/1 - 03/12
Section 04 Concrete Work............................................................................................... 04001 - 04126 ............... 04/1 - 04/17
Section 05 Brickwork and Blockwork............................................................................. 05001 - 05096 ............... 05/1 - 05/11
Section 06 Masonry......................................................................................................... 06001 - 06035 ............... 06/1 - 06/9
Section 07 Roofing and Waterproofing........................................................................... 07001 - 07148 ............... 07/1 - 07/22
Section 08 Carpentry and Joinery.................................................................................... 08001 - 08271 ............... 08/1 - 08/34
Section 09 Ironmongery.................................................................................................. 09001 - 09337 ............... 09/1 - 09/26
Section 10 Steel and Metal Work.................................................................................... 10001 - 10464 ............... 10/1 - 10/56
Section 11 Plastering and Finishes.................................................................................. 11001 - 11455 ............... 11/1 - 11/46
Section 12 Roadwork and Cable Duct............................................................................. 12001 - 12066 ............... 12/1 - 12/14
Section 13 Plumbing and Drainage................................................................................. 13001 - 13568 ............... 13/1 - 13/64
Section 14 Glazing.......................................................................................................... 14001 - 14160 ............... 14/1 - 14/19
Section 15 Painting......................................................................................................... 15001 - 15330 ............... 15/1 - 15/44
Section 16 Repairs and Alteration to Specialty Works..................................................... 16001 - 16043 ............... 16/1 - 16/13
Section 17 Labour........................................................................................................... 17001 - 17049 ............... 17/1 - 17/7
Section 18 Temporary Plant and Facilities ..................................................................... 18001 - 18055 ............... 18/1 - 18/11
Section 19 Recreational / Sports Surfacing and Protective Padding................................. 19001 - 19076 ............... 19/1 - 19/18
Section 20 Fixtures and Fittings...................................................................................... 20001 - 20384 ............... 20/1 - 20/45
Section 21 Demountable Partition, Dry Wall and Cubicle System................................... 21001 - 21104 ............... 21/1 - 21/15
Section 22 Landscape Work............................................................................................ 22001 - 22266 ............... 22/1 - 22/29
Section 23 Geotechnical Works....................................................................................... 23001 - 23108 ............... 23/1 - 23/25
Section 24 Preservation and Protection of Preserved Trees............................................. 24001 - 24006 ............... 24/1 - 24/5
Section 25 Control Treatment on Pests, Termites and Red Imported Fire Ants................ 25001 - 25020 ............... 25/1 - 25/7
1 of 3
VOLUME 1 (Cont'd)
CONTENTS
Items Pages
Section 61 Site Safety...................................................................................................... 61001 - 61010 ............... 61/1 - 61/7
Section 62 Site Cleanliness and Tidiness......................................................................... 62001 - 62002 ............... 62/1 - 62/3
Section 63 Trip Ticket System......................................................................................... 63001 - 63002 ............... 63/1 - 63/3
Section 64 Monitoring Payment of Wages...................................................................... 64001 - 64003 ............... 64/1 - 64/5
Section 65 Sub-contractor Management Plan ................................................................. 65001 - 65002 ............... 65/1 - 65/2
Section 66 Uniform......................................................................................................... 66001 - 66001 ............... 66/1 - 66/2
Annex 'A' - Drawing Schedule and Drawings for Builder's Works ................................................................................................. A/1 - A/29
Annex 'B' - Grouping of Plant Materials.......................................................................................................................................... B/1 - B/8
Annex 'C' - Tables of Metal Weights, etc........................................................................................................................................ C/1 - C/34
VOLUME 2
CONTENTS
Items Pages
Section 00 General Regulations .................................................................................................................................... 00/1 - 00/19
Section 01 Contract Facilities and Special Attendances................................................... 01001 - 01017 ............... 01/1 - 01/9
Section 27 Electrical Installation - Lighting System and Fixtures.................................... 27001 - 27798 ............... 27/1 - 27/70
Section 28 Electrical Installation - Small Power Distribution.......................................... 28001 - 28593 ............... 28/1 - 28/37
Section 29 Electrical Installation - Main Distribution Systems........................................ 29001 - 29730 ............... 29/1 - 29/38
Section 30 Electrical Installation - Miscellaneous............................................................ 30001 - 30859 ............... 30/1 - 30/57
Section 31 Low Voltage Cubicle Switchboard................................................................. 31001 - 31123 ............... 31/1 - 31/10
Section 32 Emergency Generator Installation.................................................................. 32001 - 32108 ............... 32/1 - 32/11
Section 33 Burglar Alarm and Security........................................................................... 33001 - 33099 ............... 33/1 - 33/13
Section 34 Public Address System ................................................................................. 34001 - 34037 ............... 34/1 - 34/6
Section 35 Broadcast Reception...................................................................................... 35001 - 35022 ............... 35/1 - 35/5
2 of 3
VOLUME 2 (Cont'd)
CONTENTS
Items Pages
Section 36 Heating, Ventilation and Air-Conditioning - Pipework ................................. 36001 - 36587 ............... 36/1 - 36/43
Section 37 Heating, Ventilation and Air-Conditioning - Ductwork ................................ 37001 - 37208 ............... 37/1 - 37/15
Section 38 Heating, Ventilation and Air-Conditioning - Equipment................................ 38001 - 38699 ............... 38/1 - 38/55
Section 39 Heating, Ventilation and Air-Conditioning - Electrical Power Supply,
Control and Monitoring System..................................................................... 39001 - 39068 ............... 39/1 - 39/7
Section 40 Fire Services.................................................................................................. 40001 - 40356 ............... 40/1 - 40/32
Section 41 Liquefied Petroleum Gas............................................................................... 41001 - 41091 ............... 41/1 - 41/13
Section 42 Town Gas...................................................................................................... 42001 - 42048 ............... 42/1 - 42/7
Section 43 Medical Gases............................................................................................... 43001 - 43259 ............... 43/1 - 43/26
Section 44 Catering Equipment....................................................................................... 44001 - 44095 ............... 44/1 - 44/14
Section 45 Swimming Pool Water Treatment Installation............................................... 45001 - 45110 ............... 45/1 - 45/15
Section 46 Crane and Hoist Installation........................................................................... 46001 - 46025 ............... 46/1 - 46/5
Section 47 Fuel Supply System....................................................................................... 47001 - 47050 ............... 47/1 - 47/9
Section 48 Chimney........................................................................................................ 48001 - 48075 ............... 48/1 - 48/8
Section 49 Sewage Treatment Installation....................................................................... 49001 - 49039 ............... 49/1 - 49/9
Annex 'A' - Drawings for Building Services Works ........................................................................................................................ A/1 - A/9
3 of 3
Section 00
GENERAL REGULATIONS
00 GENERAL REGULATIONS 00
SECTION 00
GENERAL REGULATIONS
Associated GR.01 This Schedule of Rates (hereinafter referred to as this Schedule or "the Schedule") shall
documents be read and used in conjunction with : -
(a) The General Conditions of Contract and Special Conditions of Contract
adopted for the Term Contract.
(b) The Conditions of Tender, Form of Tender and Articles of Agreement of the
Term Contract.
(c) Drawings, Specification and Employers Requirements of the Term Contract.
(d) The term Specification shall mean the General Specification, Codes of
Practice and other documents referred herein below, Particular Specifications
and all other specification requirements issued therein and referred to in the
Term Contract.
(e) The General Specifications and other documents for building works as listed
below including all current amendments issued thereto and referred to in the
Term Contract : -
(i) General Specification for Building issued by Architectural Services
Department.
(ii) Appropriate Sections of General Specification for Civil Engineering
Works issued by Civil Engineering and Development Department.
(iii) Design Manual : Barrier Free Access issued by Buildings Department.
(iv) Code of Practice for Fire Resisting Construction issued by Building
Authority, Hong Kong.
(v) The Fresh Water Plumbing Maintenance Guide, Handbook on Plumbing
Installation and Hong Kong Waterworks Standard Requirements For
Plumbing Installation in Buildings issued by Water Supplies Department.
(f) The General Specifications, Codes of Practice and other documents for building
services installations as listed below, which are issued by Architectural Services
Department or Electrical and Mechanical Services Department including all
current amendments issued thereto and referred to in the Term Contract : -
(i) General Specification for Electrical Installation in Government Buildings
of the Hong Kong Special Administrative Region issued by Architectural
Services Department.
(ii) General Specification for Air Conditioning, Refrigeration, Ventilation
and Central Monitoring and Control System Installation in Government
Buildings of the Hong Kong Special Administrative Region issued by
Architectural Services Department.
00/1
00 GENERAL REGULATIONS 00
Associated GR.01 (f) (iii) General Specification for Mechanical Installation in Government
documents (Cont'd) Buildings of the Hong Kong Special Administrative Region issued
(Cont'd) by Architectural Services Department.
(iv) General Specification for Fire Service Installation in Government
Buildings of the Hong Kong Special Administrative Region issued
by Architectural Services Department.
(v) General Specification for Lift, Escalator and Passenger Conveyor
Installation in Government Buildings of the Hong Kong Special
Administrative Region issued by Architectural Services Department.
(vi) General Specification for Liquefied Petroleum Gas Installation in
Government Buildings of the Hong Kong Special Administrative
Region issued by Architectural Services Department.
(vii) General Specification for Catering Equipment Installation in
Government Buildings of the Hong Kong Special Administrative
Region issued by Architectural Services Department.
(viii) General Specification for Swimming Pool Water Treatment
Installation in Government Buildings of the Hong Kong Special
Administrative Region issued by Architectural Services Department.
(ix) General Requirement for Electronic Contract (ESG01) issued by
Electrical and Mechanical Services Department
(x) General Specification for Broadcast Reception Installation in
Government Buildings of the Hong Kong Special Administrative
Region issued by Architectural Services Department.
(xi) General Specification for Public Address Systems (ESG11) issued by
Electrical and Mechanical Services Department.
(xii) General Technical Specification for Monochrome and Colour Closed
Circuit Television Systems (ESG14) issued by Electrical and
Mechanical Services Department.
(xiii) General Technical Specification for Uninterruptible Power Supply
(UPS) (ESG15) issued by Electrical and Mechanical Services
Department.
(xiv) General Specification for Plumbing and Drainage Installation in
Government Buildings of the Hong Kong Special Administrative
Region issued by Architectural Services Department.
(xv) Code of Practice for the Electricity (Wiring) Regulations issued by
Electrical and Mechanical Services Department.
(xvi) Code of Practice for Energy Efficiency of Building Services Installation
issued by Electrical and Mechanical Services Department.
00/2
00 GENERAL REGULATIONS 00
Associated GR.01 (f) (xvii) Code of Practice for Minimum Fire Services Installations and
documents (Cont'd) Equipment and Inspection, Testing and Maintenance of Installations
(Cont'd) and Equipment issued by Fire Services Department.
(xviii) Code of Practice for Lift Works and Escalator Works issued by
Electrical and Mechanical Services Department.
(xix) Testing and Commissioning Procedure for Electrical Installation in
Government Buildings of the Hong Kong Special Administrative Region
issued by Architectural Services Department.
(xx) Testing and Commissioning Procedure for Air-conditioning,
Refrigeration, Ventilation and Central Monitoring and Control System
Installation in Government Buildings of the Hong Kong Special
Administrative Region issued by Architectural Services Department.
(xxi) Testing and Commissioning Procedure for Fire Services Installation in
Government Buildings of the Hong Kong Special Administrative Region
issued by Architectural Services Department.
(xxii) Testing and Commissioning Procedure for Lift, Escalator and
Passenger Conveyor Installation in Government Buildings of the Hong
Kong Special Administrative Region issued by Architectural Services
Department.
(xxiii) Testing and Commissioning Procedure for Liquefied Petroleum Gas
Installation in Government Buildings of the Hong Kong Special
Administrative Region issued by Architectural Services Department.
(xxiv) Testing and Commissioning Procedure for Catering Equipment
Installation in Government Buildings of the Hong Kong Special
Administrative Region issued by Architectural Services Department.
(xxv) Testing and Commissioning Procedure for Swimming Pool Water
Treatment Installation in Government Buildings of the Hong Kong
Special Administrative Region issued by Architectural Services
Department.
(xxvi) Testing and Commissioning Procedure for Broadcast Reception
Installation in Government Buildings of the Hong Kong Special
Administrative Region issued by Architectural Services Department.
(xxvii) Testing and Commissioning Procedure for Burglar Alarm and Security
Installation in Government Buildings of the Hong Kong Special
Administrative Region issued by Architectural Services Department.
(xxviii) Testing and Commissioning Procedure for Emergency Generator
Installation in Government Buildings of the Hong Kong Special
Administrative Region issued by Architectural Services Department.
00/3
00 GENERAL REGULATIONS 00
Associated GR.01 (f) (xxix) Testing and Commissioning Procedure for Steam Boiler and Calorifier
documents (Cont'd) Installation in Government Buildings of the Hong Kong Special
(Cont'd) Administrative Region issued by Architectural Services Department.
(xxx) Testing and Commissioning Procedure for Plumbing and Drainage
Installation in Government Buildings of the Hong Kong Special
Administrative Region issued by Architectural Services Department.
(g) Particular Specification(s) and all other specification requirements issued and
referred to in the Term Contract.
(h) Any Amendments to the Schedule of Rates issued and referred to in the Term
Contract.
All items of works contained in this Schedule and in the Amendments to the Schedule
of Rates issued and referred to in the Term Contract, shall be executed in accordance
with the conditions and stipulations as provided in the above mentioned documents, and
in compliance with all requirements on workmanship, materials, plant, measurements
and any other requirements as stipulated in the above documents.
Due allowance is deemed to have been made in the Contract Percentages for complying
with the requirements in the Specification and/or Employer's Requirements as adopted
in the Term Contract.
Definitions GR.02 Where any of the definitions given in these General Regulations are at variance with
generally those given in the Special Conditions preceding the Sections throughout this Schedule,
the definitions given in the Sections in this Schedule shall take priority.
approved shall mean approved in writing by the Maintenance Surveyor but this
approval shall not relieve the Contractor from responsibilities
imposed by the Term Contract.
described shall mean described in the Specification and all current amendments
(if any) issued thereto.
ditto shall mean the whole of the work described in detail in the preceding
item, except as qualified in the description in which it occurs.
origin shall mean the place or country where the material (which shall be
natural material only) is originally produced.
proprietary shall mean a proprietary material or product, protected by a patent or
registered trade mark or a trade mark symbol or similar
recognizable trade mark or copyright, that is manufactured and
marketed by the owner who has exclusive rights of use, or other
material or product that the Contractor could provide authentication
documents on its make and origin as required by the Maintenance
Surveyor and to his satisfaction.
00/4
00 GENERAL REGULATIONS 00
Definitions GR.02 Schedule shall mean this Schedule of Rates.
generally (Cont'd)
(Cont'd) specified shall mean specified in the Specification and all current amendments
(if any) issued thereto.
submission shall mean the submission of all documents like design, calculation,
working drawings, shop drawings, records, etc. as required in the
Special Conditions to each Section of the Schedule including obtaining
the approval of the Maintenance Surveyor on the submission.
"Term Contract" shall mean the Contract referring this Schedule as forming part of the
Contract.
Abbreviations exc. shall mean exceeding.
n.e. shall mean not exceeding.
c/w shall mean complete with.
xx - yy shall mean a range of dimensions exceeding the first dimension as stated
but not exceeding the second, for example: "1.50 - 3.00" shall mean
exceeding 1.50 and not exceeding 3.00.
bore shall mean nominal internal diameter.
dia shall mean nominal diameter.
mm shall mean millimetre.
m shall mean linear metre.
m shall mean square metre.
m shall mean cubic metre.
kg shall mean kilogram.
"B.S." shall mean British Standard.
"DBH" shall mean diameter at breast height of trees.
"EN" shall mean European Standard.
G.S. shall mean the General Specification and other documents referred to in
General Regulations Clause GR.01(e) and (f) where appropriate.
"MDF" shall mean medium density fibreboard.
RSE shall mean Registered Structural Engineer.
TCP shall mean Technically Competent Person.
00/5
00 GENERAL REGULATIONS 00
Methods of GR.03 All works including Supply only of materials measured and paid for under this Schedule
measurement shall be measured in accordance with the conditions and rules detailed herein irrespective
of any local or trade customs.
All works shall be measured net as completed or fixed in its place. Due consideration has
been made in the Schedule rates for works executed in small quantities, narrow widths,
short lengths, isolated patches, repairs, any height or locations above or below ground,
difficult positions or confined spaces or any other exceptional circumstances; and no
additional payment for such circumstances shall be made except where specifically
provided for in this Schedule.
All works of Supply only of materials shall be the net quantities specified in a Works
Order. No allowance or payment will be made to the Contractor for small quantities, short
lengths, breakage or damage, delivery to store or any designated location as directed by
the Maintenance Surveyor or any other circumstance except where specifically provided
for in this Schedule.
Any disadvantage which may be entailed by items being performed under exceptional
circumstances must be regarded as being offset by other items which may be proven
exceptionally advantageous.
Overtime GR.04 All works shall be deemed to be executed during any working hour in a 24 hour-day
(from 00:00 hour to 24:00 hour) including Sundays and General Holidays. No additional
payment will be made for any overtime including : -
(a) Overtime which is ordered by the Maintenance Surveyor in accordance with the
Conditions of Contract to expedite slow progress of the work caused by default,
negligence or omission by the Contractor.
(b) Watchmen or security guard at any time.
Deductions for GR.05 Where a minimum area is defined for the deduction of voids, such minimum shall refer only
voids to openings or voids detached from the boundaries of the space measured. Reductions of
area caused by projections or recesses from the boundary of the area measured shall
always be deducted irrespective of size.
Curved or GR.06 Except where specified items are included in this Schedule for curved or circular work, all
circular works work shall be measured and priced as if straight and flat. Where specific items for curved
work or circular work are included, the maximum radius stated in such description shall
be the limit for which curved or circular work will be paid for and any work curved to a
radius greater than this limit shall be measured and priced as if straight and flat.
00/6
00 GENERAL REGULATIONS 00
Works executed GR.07 Where appropriate throughout this Schedule and where specified in the Term Contract,
by Specialist the following categories of works shall be executed by : -
Sub-contractors,
sub-contractors, (a) Specialist Sub-contractors included in the list of Approved Suppliers of Materials
etc. and Specialist Contractors for Public Works maintained by Development Bureau
namely : -
(i) Air-conditioning Installation
(ii) Audio Electronics Installation
(iii) Broadcast Reception Installation
(iv) Burglar Alarm and Security Installation
(v) Catering Equipment Installation
(vi) Design, Manufacture and Installation of Glass (or Fibre) Reinforced
Plastic Units
(vii) Diesel Generator Installation
(viii) Electrical Installation
(ix) Electrical and Mechanical Installation for Sewage Treatment and Screening
Plant
(x) Electronic Timing and Display Installation
(xi) Fabrication of Steel Pipe Specials
(xii) Fabrication of Unfired Pressure Vessels
(xiii) Fire Service Installation
(xiv) Fountain Installation
(xv) Landscaping
(xvi) Landslip Preventive/Remedial Works to Slopes/Retaining Walls
(xvii) Lift, Escalator and Passenger Conveyor Installation
(xviii) Liquefied Petroleum Gas Installation
(xix) Low Voltage Cubicle Switchboard Installation
(xx) Mechanical Handling and Lifting Installation
00/7
00 GENERAL REGULATIONS 00
Works executed GR.07 (a) (xxi) Mechanical Plant and Equipment Installation
by Specialist (Cont'd)
Sub-contractors, (xxii) Plumbing Installation
sub-contractors,
etc. (xxiii) Radio Electronics Installation
(Cont'd)
(xxiv) Repair and Restoration of Historic Buildings
(xxv) Repair of Motors, Transformers and Switchgear
(xxvi) Road Marking
(xxvii) Soil and Rock Testing
(xxviii) Space Frame Systems
(xxix) Steam and Compressed Air Installation
(xxx) Structural Steelwork
(xxxi) Supply and Installation of Pumpsets and Associated Pipework
(xxxii) Supply and Installation of Water Treatment Plant
(xxxiii) Supply of Bituminous Pavement Materials and Construction of Special
Bituminous Surfacing
(xxxiv) Swimming Pool Water Treatment Installation
(xxxv) Turn-key Interior Design and Fitting-out Works
(xxxvi) Uninterruptible Power Supply Installation
(xxxvii) Video Electronics Installation
(b) Maintenance Surveyor's approved sub-contractors or applicators namely : -
(i) Medical Gas
(ii) Town Gas
(iii) Curtain Walling
The above categories of specialist works are not exhaustive. Other categories of works,
if specified in the Term Contract, shall also be executed by Specialist Sub-contractors
or other approved sub-contractors or applicators.
Due allowance is deemed to have been made in the Contract Percentages for complying
with these requirements.
00/8
00 GENERAL REGULATIONS 00
Latest standards GR.08 Where materials, workmanship and works are specified in this Schedule to be in
and specification conformity with certain British Standards or other International Standards, or to be
in accordance with certain G.S. Items, Code of Practice and the like, they shall deem
to be referred to the latest relevant and equivalent standards and specification current
and published before the date of first tender invitation for the Term Contract unless
otherwise specified. If conflict occurs between various standards, then the more onerous
is to apply.
Due allowance is deemed to have been made in the Contract Percentages for complying
with these requirements.
Imperial equivalents GR.09 Whenever practicable, the Contractor shall supply materials in metric sizes and execute
where required or the works strictly in accordance with the metric dimensions specified. Imperial equivalents
necessary may be accepted only when circumstances prohibit compliance with this sub-clause (for
example, statutory obligations) or where the Maintenance Surveyor considers it impracticable,
undesirable or impossible to use metric sizes or dimensions or when suitable materials are
not available in metric sizes.
The provision of this sub-clause shall not apply to materials which are specified in this
Schedule by their actual manufactured sizes or their metric equivalents (for example, roof
tiles, plywood, building boards, p.v.c. pipes, mosaic tiles) or classified in accordance with
the relevant British Standards (for example, copper pipes) or other International Standards.
Schedule rates GR.10 The rates throughout this Schedule shall include for : -
(a) All materials supplied, and all works and services executed complying strictly with the
Specification as detailed in General Regulations Clause GR.01 and the provision or
execution of all samples of materials or finished works in patterns where required.
(b) Provision of all materials and cutting and wastage on the same, except where
otherwise stated, including collection, loading, conveyance, delivery, unloading,
stacking, storage of the same, multi-handling between positions as directed on
Site and provision of storage accommodation, handling, hoisting, lowering,
distributing, etc. to specified location.
(c) Provision of all labour including contributions to Mandatory Provident Fund, paid
leave, travelling expenses, lodging allowance or living accommodation and any
other allowances as required.
(d) Provision of all tools, plant, temporary water, power and lighting, watching and
work sheds.
(e) All expenses for delivery, distribution or transportation of articles, materials, labour,
personnel, tools, plant, work sheds etc. by all means including land, sea or air
except otherwise specifically provided for in the Special Conditions of each Section
in this Schedule or when specifically required and ordered by the Maintenance
Surveyor.
00/9
00 GENERAL REGULATIONS 00
Schedule rates GR.10 (f) Executing work in any position, location and height unless otherwise stated.
(Cont'd) (Cont'd)
(g) Providing record of photograph, location plan and schedule of existing trees, if
any, within and in close vicinity (within 2.00 m) of the site boundary and works
areas including protective and preservative works/measures such as tree surgery
works, temporary fencing, etc. and the like, allowance for method of operation
and vehicular access for tree preservation throughout the period of Works and
removing all temporary protective and preservative works/measures on
completion and making good all works disturbed.
(h) Setting up monitor points for controlling noise, vibration, settlement and lateral
movement imposed on adjoining properties including provision of equipment,
technical and supervisory personnel carrying out daily monitoring and submission
of records as directed by the Maintenance Surveyor.
(i) Provision and maintaining temporary access and road as G.S. Item 1.25 and
making good to match existing.
(j) Provision and maintaining temporary drainage system as G.S. Item 1.26 and
making good to match existing.
(k) Provision of drawings, operation manuals and tests on samples or finished works.
(l) Allowance for the works to be executed by Specialist Sub-contractors, Maintenance
Surveyor's approved sub-contractors and applicators where required in the
Specification, or as stated in the Special Conditions of each Section of the
Schedule.
(m) Testing and certification including the employment of independent certification
bodies wherever required or necessary.
(n) Provision, erection, maintenance, alterations, dismantling and clearing away of the
following temporary works and protective measures that are required for the
execution and completion of the Works unless specifically provided otherwise in
the Schedule : -
(i) All bamboo, metal or any proprietary scaffolding, staging, ladders, trestles,
cradles, gondolas, platforms and similar items complete with all netting,
coverings, screens, dust sheets, barricades, catch-fans, protective canopies,
etc.;
(ii) All types of hoardings and walkways complete with gateways, adequate
lighting, associated power supply and electrical work as required by the
Maintenance Surveyor including the types of hoardings and walkways
referred to in Section 10 - Steel and Metal Work of this Schedule and
other proprietary hoardings and walkways systems, and the submission
of detailed drawings together with supporting calculations certified by
TCP or RSE for approval and provide operation manuals of other
proprietary hoardings and walkways systems not referred to in Section
10 - Steel and Metal Work; and
00/10
00 GENERAL REGULATIONS 00
Schedule rates GR.10 (n) (iii) Similar temporary measures including but not limited to protective
(Cont'd) (Cont'd) shield coverings, fences, barriers and the like and/or other protective
measures specifically covered by the Special Conditions of each Section
in this Schedule, and the erection, alteration and dismantling of such
temporary measures on a daily basis where required by the Maintenance
Surveyor for all necessary protection to new works and the public from
harm, dust or nuisance.
The drawings referred to in Section 10 - Steel and Metal Work of this Schedule
and in sub-clause (ii) above are not exhaustive and would be subject to change.
The Contractor is deemed to allow for complying with the latest requirements.
(o) Clearing away debris, surplus materials or other materials arising from the works
and leaving the works and areas affected by the works clean and tidy on completion
to the satisfaction of the Maintenance Surveyor.
(p) Provision of mechanical dump truck covers in accordance with Particular
Specification for Mechanical Dump Truck Covers.
(q) All superintendence, establishment charges, overhead, expenses and profit.
(r) Any cost and/or expenses incurred for carrying out the works at all times including
working outside normal working hours as provided in General Regulations Clause
GR.04.
(s) Any costs and/or expenses in supplying materials or products to match existing
works, finishes or systems when instructed by the Maintenance Surveyor, except
when such materials or products are not specifically mentioned in this Schedule.
(t) Any other expenses incurred in conforming with the Term Contract.
(u) Reinstatement and making good surfaces disturbed.
(v) Imperial equivalents wherever required or necessary.
Where the Contractor considers any of the rate contained in the Schedule is insufficient or
inadequate, the Contractor is deemed to have made all necessary allowances in the Contract
Percentages adjustment and/or in any other priced items in the Term Contract for executing
the works as contained in the Schedule and in compliance with all requirements as stipulated
in the Term Contract.
00/11
00 GENERAL REGULATIONS 00
Rates for items GR.11 Rates for items not specifically mentioned in this Schedule shall be valued as follows : -
not specifically
mentioned in (a) Proportional rate When an article, a material, workmanship or service is
this Schedule of similar form, character or quality to that detailed in
the Schedule or executed under similar conditions and
circumstances as described therein, then at a rate equal
to a Schedule rate but with a fair adjustment for the
difference in form, character and quality or in conditions
and circumstances, and such rate to be agreed upon
between the Maintenance Surveyor and the Contractor.
Such proportional rate shall be subject to relevant
Contract Percentage adjustment.
(b) Star rate When an article, a material, workmanship or service is
not of similar form, character or quality to that detailed
in the Schedule or not executed under similar conditions
and circumstances as described therein, or when work
or material of any kind which is not detailed in the
Schedule, then at a reasonable rate to be agreed upon
between the Maintenance Surveyor and the Contractor.
Such star rate shall not be subject to relevant Contract
Percentage adjustment.
(c) Re-applicable rate A rate fixed in accordance with the Term Contract
requirements and to be re-applicable in any other Works
Orders as approved by the Maintenance Surveyor for
the whole duration of the Term Contract and not subject
to adjustment of fluctuation and Contract Percentage
adjustment.
Adjustments made GR.12 The Schedule rates in this Schedule are derived from the basic rates of provisions of
to basic rates and labour, materials, plant and all other provisions as stated in this Schedule including
application of adjustments made to the basic rates giving due consideration of factors including
Contract market trends, trade practices and the management efficiency and bidding strategies
Percentages as reflected in the past term contracts procurement.
The Schedule rates also take into account conditions under which term contracts
works are executed, which may include but not be limited to works executed in small
quantities or large quantities, narrow widths, short lengths, isolated patches, repairs,
any height or locations above or below ground, difficult positions or confined spaces
or any other exceptional circumstances of the works.
In all cases, the Schedule rates shall be applied in the valuation of works before
applying any relevant Contract Percentages contained in the Form of Tender of the
Term Contract.
The Contract Percentages including any percentage addition as contained in the
Form of Tender shall include the Contractor's profits and overheads, attendance,
all costs and expenses incurred in connection with the Works and are necessary in
fulfilling the requirements of the Term Contract where they are not separately itemized
or stated in this Schedule, including the works or services assessed under proportional
rate items, star rate items and re-applicable rate items.
00/12
00 GENERAL REGULATIONS 00
Materials supplied GR.13 When materials are supplied to the Contractor by Government or other designated
by Government or suppliers, no allowance will be made to the Contractor other than the payment for
other designated Fix only (Lay only or Set only, etc.) as detailed under the appropriate items of
suppliers this Schedule.
Supply only GR.14 The term Supply only used throughout this Schedule shall mean the provision
complete by the Contractor of an article, a fitting or a material. The rates for such
items shall include for, where applicable, obtaining and taking delivery of the article,
fitting or material, transporting by land, sea, or air to sites or Government stores or
other designated locations as directed by the Maintenance Surveyor, and all necessary
off-loading and moving into sites, Government stores or other designated locations.
The rates listed in the SUPPLY ONLY OF MATERIALS in each Section of this
Schedule shall include all the foregoing charges and allowance for replacement of
materials damaged during delivery to sites, off-loading and moving into sites,
Government stores or other designated locations as directed by the Maintenance
Surveyor.
Take down GR.15 The term Take down (Take up or Take out, etc.) and clear away used
(Take up or throughout this Schedule shall mean execution complete by the Contractor of the
Take out, etc.) work of taking down, taking up or taking out of an existing article, fitting or material
and clear away either in whole or in part and removing from Site and disposing of the same. The rates
for such items shall include for all or any of the following : -
(a) Works executed by skilled labourers of the required trades, unless
specifically provided otherwise in the Schedule.
(b) Payment of all fees and charges.
(c) Taking down, taking up or taking out of the article, fitting or material either in
whole or in part together with any associated plugs, holdfasts, lugs, brackets
and other fixings and all necessary cutting out and disposal.
(d) Making good any works disturbed and any damage to surrounding surfaces and
filling up all mortices, holes, etc. or alternatively leaving the same open and
clean to receive readily new articles, fittings or materials.
(e) Reinstatement and making good surfaces disturbed by specialists.
(f) Preparing edges, ends or surfaces of remaining material to receive junction with
new.
(g) Taking up or removing covers, access doors, etc. and the like for the execution
of the works and re-fixing the same on completion.
The articles, fittings, or materials taken down shall become property of the Contractor.
Unless otherwise specified, due allowance for credit has been considered in the
Schedule rates where applicable.
00/13
00 GENERAL REGULATIONS 00
Take down (Take GR.16 The term Take down (Take up or Take out, etc.) and set aside for re-use used
up or Take out, throughout this Schedule shall mean execution complete by the Contractor of the
etc.) and set aside work of taking down, taking up or taking out of an existing article, fitting or material
for re-use either in whole or in part and setting the same aside on site or transporting to
Government stores or other Government sites for subsequent re-use. The rates for
such items shall include for all or any of the following : -
(a) Works executed by skilled labourers of the required trades, unless specifically
provided otherwise in the Schedule.
(b) Payment of all fees and charges.
(c) Carefully taking down, taking up or taking out of the article, fitting or material
together with associated plugs, holdfasts, lugs, brackets and other fixings and
all necessary cutting out and disposal.
(d) Thoroughly cleaning, oiling and adjusting the article, fitting or material ready
for re-use, dismantling, re-assembling again as necessary, moving and
stacking or putting into stores on sites or alternatively loading, transporting,
unloading and moving to Government stores or other Government sites.
(e) Making good any works disturbed and any damage to surrounding surfaces
and filling up all mortices, holes, etc. or alternatively leaving the same open
and clean to receive readily re-used or new articles, fittings or materials.
(f) Reinstatement and making good surfaces disturbed by specialists.
(g) Preparing edges, ends or surfaces of remaining material to receive junction
with re-used or new.
(h) Repairing or replacing at Contractor's own cost any damage caused to the
articles, fittings or materials during taking down, taking up, taking out, etc.
and transit.
(i) Taking up or removing covers, access doors, etc. and the like for the
execution of the works and re-fixing the same on completion.
Fix only GR.17 The term Fix only (Lay only or Set only, etc.) used throughout this Schedule
(Lay only shall mean execution complete by the Contractor of the work of fixing, laying, setting,
or Set only, jointing, re-fixing, re-laying, re-setting and re-jointing an article, a fitting or a material
etc.) made available free of charge to the Contractor by Government or it has been previously
taken down. The prior taking down of the existing articles, fittings or materials shall be
measured separately and paid for at the appropriate rates under applicable Sections of
this Schedule. The rates for such items shall include for any or all of the following : -
(a) Works executed by skilled labourers of the required trades, unless specifically
provided otherwise in the Schedule.
(b) Payment of all fees and charges.
00/14
00 GENERAL REGULATIONS 00
Fix only GR.17 (c) Taking delivery of the articles, fittings or materials at Government stores or
(Lay only (Cont'd) other designated suppliers, loading, transporting to sites, unloading, checking
or Set only, and examining the same and storing on sites and returning any crates and
etc.) other packings to Government stores, if required.
(Cont'd)
(d) Taking the articles, fittings or materials from stores on sites, sorting, cutting and
fitting, fabricating, assembling, moving, hoisting, distributing at locations, fixing,
laying, setting, jointing, re-fixing, re-laying, re-setting and re-jointing in new or
existing work, opening or position.
(e) Providing all fixing and jointing materials such as nails, bolts, nuts, washers,
screws, gaskets, mastic, adhesive, mortar and the like or other fixing and
jointing materials made available from taking down.
(f) Executing all plugging and screwing, jointing, cutting all mortices and grouting
the same, and executing all cutting, fitting, easing or adapting necessary to the
articles, fittings or materials to the positions in which the same are to be fixed,
and oiling and leaving in good working order.
(g) Making good any damage caused to the articles, fittings or materials and
surrounding surfaces and making good new or existing finishes up to the same.
(h) Reinstatement and making good surfaces disturbed by specialists.
When the articles, fittings or materials despite having been taken down from another
positions and set aside for re-use or having been delivered by Government or other
designated suppliers or their agents are made available on site, no deduction will be
made from the rates of Fix only(Lay only or Set only, etc.) for transporting the
said articles, fittings or materials to Site.
Built up fittings or GR.18 The rates for Take down and clear away, Take down and set aside for re-use and
composite units Fix only are not intended to cover built up fittings or composite units, i.e. fittings or
units that are fabricated and can be moved in their entirety or broken down into
fabricated components. These items are to be measured as the appropriate items in
the respective Sections unless otherwise provided in this Schedule.
Nominated GR.19 When works are carried out by Nominated Sub-contractors and facilities for the
Sub-contractors' execution of such works are afforded to the Nominated Sub-contractors by the
accounts Contractor and accounts for such works are paid by the Contractor in accordance
with the Conditions of Contract, the percentage addition allowed to the Contractor
on the net cost of such works shall be as that contained in the Form of Tender for
Profit and Attendance on Nominated Sub-contractors' Works.
00/15
00 GENERAL REGULATIONS 00
Making good GR.20 The term Making good shall be understood as including all labour and materials
necessary to bring the disturbed area to the same face, colour, texture, etc., in the
same materials as the surrounding work and shall include for painting, colouring
and/or varnishing any new work to match the surrounding existing work to the entire
satisfaction of the Maintenance Surveyor.
Daywork GR.21 When daywork is ordered by the Maintenance Surveyor, measurement of daywork
shall be made according to the Special Conditions set out in Section 17 - Labour and
Section 18 - Temporary Plant and Facilities of this Schedule.
Utility Connection GR.22 The term Utility Connection And Pavement Works shall mean the works of
And Pavement drainage connection, water supply connection, construction of run-in and
Works reinstatement of footways which shall be executed complete by contractors selected
and employed by the Contractor from the List of Approved Contractor for Public
Works in Group A, B or C for Road & Drainage Works for the drainage connection
and construction of run-in and reinstatement of footways and from the List of
Approved Contractors for Public Works in Group A, B or C for Waterworks for
the water supply connection work.
When Utility Connection and Pavement Works are required to be executed under the
Term Contract and are ordered specifically by the Maintenance Surveyor for such
purpose, the Contractor will be reimbursed a lump sum fee payment as included in
Item 03063 in Section 03 Excavation of this Schedule for compliance with the
requirements stated herein and as provided in the Term Contract for the Utility
Connection and Pavement Works. This lump sum fee payment is an allowance made
for all costs and expenses other than the valued works executed in connection with the
Utility Connection and Pavement Works under the relevant Sections in this Schedule,
and shall include for the following :-
(a) Complying with the requirements and procedures in connection with the
Utility Connection And Pavement Works specified in the Particular
Specification referred to in the Term Contract and submitting assessments
and reports as required.
(b) Liaising with the relevant authorities and utility companies, preparing and
submitting relevant drawings, programmes and documents and completing all
the forms in connection with the Utility Connection And Pavement Works.
(c) Submitting all the detailed particulars in connection with the granting of an
Excavation Permit [Note : Excavation Permit means any excavation permit
issued by the Government in respect of the Utility Connection And Pavement
Works under Section 8 of the Land (Miscellaneous Provision) Ordinance] as
required by the Maintenance Surveyor.
00/16
00 GENERAL REGULATIONS 00
Utility Connection GR.22 (d) Obtaining approvals and permits from relevant utility companies or
And Pavement (Cont'd) Government departments.
Works
(Cont'd) (e) Complying with the conditions of any Excavation Permit applicable to the
Utility Connection And Pavement Works.
(f) Providing and maintaining temporary road or access where required for
pedestrian and vehicular traffic diversions and subsequent clearing away after
completion of Works.
(g) Providing and maintaining traffic control as G.S. Item 1.18.
(h) Locating and protecting existing services as G.S. Item 1.22.
(i) Carrying out all necessary site inspections (including handing over
inspections) jointly with the relevant authorities and utility companies.
(j) Provision of identification tapes along the water connection mains.
(k) Cleaning and sterilization of fresh water mains for making connections.
(l) Provision of as built drawings and test reports as specified.
(m) Protection of curbs, masking and unmasking of drainage channels, manhole
covers, gully gratings, expansion joints, road studs and road marking.
(n) Provision, maintenance and removal of all measures to maintain traffic flow
including labour and temporary traffic diversion lighting and signs and paying
all charges incurred.
(o) Provision, maintenance and removal of temporary road, walkway, covers to
trenches and the like.
(p) Making good all surfaces, features, etc. and the like disturbed by all
temporary road, access, traffic control, pedestrian footway, etc. and the like
to match existing and including all requirements as stipulated in the Term
Contract for carrying out the Utility Connection and Pavement Works.
This lump sum fee payment shall only be paid once for each project or each location
specified in the Works Order. Works executed in connection with the Utility Connection
and Pavement Works will be measured separately as in accordance with the General
Regulations and the Special Conditions of the relevant Sections in this Schedule.
Submission of GR.23 All quantities shall be measured and rounded to the nearest two decimals of a unit.
measurement
and accounts
00/17
00 GENERAL REGULATIONS 00
Materials/ GR.24 All materials/products shall generally be based on the corresponding properties and/or
Products performance standards as stipulated in the Specification (as defined in General
Regulations Clause GR.01(d) herein) and/or as set out in this Schedule.
Where materials, products or works in this Schedule are stipulated as "proprietary",
"approved", of "specific quality" or by their origins of which properties and/or
performance standards are specified without their brand names, authentication
document on such materials, products or works including certificates of origins,
technical literatures and catalogues, compliance test reports, manufacturers'
guarantees or warranties, samples and mock-ups of these materials, products or
works and other document as required by the Maintenance Surveyor should be
submitted or provided for the Maintenance Surveyor's written approval before
purchase, delivery and execution. If any of these materials, products or works
delivered or executed without the Maintenance Surveyor's prior written approval,
or are not carried out to the Maintenance Surveyor's satisfaction, they should be
removed or reinstated by the Contractor at his own expenses.
For all materials, products and works within the definition of "proprietary" in General
Regulations Clause GR.02, the Contractor, if required by the Maintenance Surveyor,
shall provide a certificate of patent or registered trade mark or copy right; or provide
authentication documents on the make or origin of the materials or products; and
provide local project reference to demonstrate that the materials, products and works
have proven track record of similar application, all to the satisfaction of the Maintenance
Surveyor. The Contractor shall further be required to have specific proprietary materials
/ products/works executed by approved sub-contractors/applicators and submit
technical literatures, method statements, etc. where required by the Maintenance
Surveyor or as stated in the Term Contract.
Due allowance is deemed to have been made in the Contract Percentages for complying
with all of the above requirements.
Materials/Products GR.25 Certain materials/products in this Schedule are stipulated as of specific quality. These
specified as shall generally be materials/products of significance, such as those that are safety critical,
specific quality prestigious in nature, or such are required to create a specific visual impact to the completed
works, or are critical to the completed works from their functionality, operation and
maintenance perspectives that the quality of such materials/products exceeds the requirement
generally stated in the General Specification and in the Term Contract.
The Contractor shall provide authentication of documentary evidence and proof including
those specified in this Clause and General Regulations Clause GR.24 herein to identify
and justify the properties and/or performance standards of "specific quality" of the subject
materials/products are generally of higher quality than that specified in the General
Specification and the requirements as stated in the Specification of the Term Contract, for
the Maintenance Surveyor's approval. Such proof may include carrying out appropriate
quality tests to verify the quality of the subject materials / products is of quality higher than
that specified in the General Specification, or obtaining certification from an independent
testing authority/expert (to be approved by the Maintenance Surveyor) confirming of such
specific quality.
Due allowance is deemed to have been made in the Contract Percentages for complying
with all of the above requirements.
00/18
00 GENERAL REGULATIONS 00
Payment for GR.26 Throughout this Schedule, the payment of materials / products shall generally be
materials/products assessed according to the corresponding properties or performance standards as set
out in this Schedule (with reference to the Specification) regardless of whether the
materials / products are specified with brand names or referred as "proprietary",
"approved", of "specific quality" or by their origins, or not.
The onus of proof is vested with the Contractor to identify the origins, properties
and/or performance standards of materials/products used in the works corresponding
to those set out in this Schedule (with reference to the Specification), and to provide
the necessary documentary evidence and authentications including but not limited to
certificates of origins, certificates of patent, registered trade marks or copy rights, local
job references of similar applications, technical literatures and catalogues, compliance
test reports, manufacturers' guarantees or warranties, sub-contractors' / applicators'
warranties and the like of the materials / products specified or approved for use by the
Maintenance Surveyor for payment of the corresponding materials / products as set
out in this Schedule.
In the absence of any documentary evidence and authentications that are required to
demonstrate the conformity or compliance of the materials/products/works with the
respective "proprietary", "approved", of "specific quality", origins or brand names, the
assessment of such materials / products / works may be based on the basic costs of the
materials / products/works, such basic costs and types of materials / products / works
shall be ascertained by the Maintenance Surveyor; or the Maintenance Surveyor shall
withhold or deduct the value of such materials / products / works that are not being
carried out to his satisfaction from the final value of the Works.
Adjustment GR.27 Whenever the unit rate for an item exceeds $99,999.99, it has been divided by a
to unit rates factor (adjustment factor) to reduce the figure to fall within $99,999.99 (adjusted
exceeding rate) for inclusion in this Schedule. Such unit rate before adjustment is described in
$99,999.99 the item description as the actual rate. When the adjusted rate is to be used for all
purposes under the Term Contract, such adjusted rate shall be multiplied by the
adjustment factor to revert it back to the actual rate before making any adjustment of
the relevant Contract Percentages.
Application of GR.28 This Schedule comprises Volume 1 for Builder's Works and Volume 2 for Building
Schedule rates Services Works (B.S. Works). The compilation of unit rates in these two Volumes of
Schedule of Rates are made with due consideration on the specific natures, purposes
and requirements which would vary for the execution of the builder's works and the
building services works.
Where similar Schedule rates are found in different Sections, whether within the same
volume or different volume of the Schedule, such valuation shall in so far as reasonable
be based on Schedule rates of the same Section under which the works are executed.
00/19
Section 01
CONTRACT FACILITIES AND SPECIAL ATTENDANCES
01 CONTRACT FACILITIES AND SPECIAL ATTENDANCES 01
SECTION 01
CONTRACT FACILITIES AND SPECIAL ATTENDANCES
SPECIAL CONDITIONS
Contract SC01.01 This Section shall be read and used in conjunction with the Specification and the
Requirements Employer's Requirements adopted in the Contract.
Contract Facilities stated in this Section shall refer to land transport facilities, contract
equipment and contract staff services provided by the Contractor for the exclusive use by
the Maintenance Surveyor, his representatives, the Employer or his staff all in accordance
with the requirements of the Contract for the Contract Period or such other period as
instructed by the Maintenance Surveyor.
Special Attendances stated in this Section shall mean the Contractor's provision of means
of access for the works in Works Orders of incidental minor maintenance and repair
nature at a height of over 10 metre where no other proper means of access is available.
Payments of Special Attendances shall satisfy the conditions as stated in Item SC01.11
below.
The Contractor shall arrange for the provisions of Contract Facilities and Special
Attendances to be readily available for use at the time or any time, for the duration and in
the manner as specified in the Contract, or otherwise as may be instructed by the
Maintenance Surveyor.
Particular SC01.02 The rates appearing in this Section are allowances for providing the Contract Facilities as
Preamble required in the Contract and Special Attendances. The Contractor is deemed to have
allowed in his Contract Percentage(s) for this and other Sections in the Schedule of Rates
of any insufficiency of rates and all other expenses incurred under the Contract for : -
(a) Meeting all contractual and statutory obligations in connection with the provision
of Contract Facilities and Special Attendances, and any other related obligations,
liabilities, risks and profit borne by the Contractor;
(b) Any of the Contract Facilities requirement which is impracticable or not available
(e.g. when the model satisfying the contract requirement is no longer available or
out of stock), the Contractor shall provide similar facilities and services satisfying
the requirement of the Contract and accepted by the Maintenance Surveyor;
(c) Any item or part thereof of any Contract Facilities that is required and specified in
the Contract but the methods of measurement provided hereunder do not measure
or have excluded such item or part thereof in this Section;
(d) The payment for Special Attendances shall in no way vitiate the provisions as
stipulated in General Regulations for all Works and Services carried out under
the Contract;
01/1
01 CONTRACT FACILITIES AND SPECIAL ATTENDANCES 01
SPECIAL CONDITIONS
Particular SC01.02 (e) Any further period of Contract Facilities provided beyond the period of
Preamble (Cont'd) measurement as provided in the Special Conditions contained in this Section and
(Cont'd) without any confirmation from the Maintenance Surveyor; and
(f) All other allowance as stipulated in the Contract in connection with the provision
of the Contract Facilities and Special Attendances.
SC01.03 The rates in this Section shall generally include for : -
(a) Maintenance, repairs, service charges, tax, license and any other government fees
and charges in connection with the use of the Contract Facilities and provisions
of Special Attendances;
(b) Provisions of all insurances on the Contract Facilities against accident, damage,
loss by theft or fire, etc.;
(c) Replacement of contract staff;
(d) Replacement of damaged or lost facilities; and
(e) Removal of the Contract Facilities within the time as stipulated in the Contract, or
at any time as may be informed by the Maintenance Surveyor.
Measurement of SC01.04 The items for Contract Facilities shall generally be measured and paid for in accordance
Contract Facilities with the Special Conditions provided below where such facilities are specifically stated in
generally the Contract. Any item(s) of Contract Facilities that are stated in the Contract but not
included in this Section, the Contractor is deemed to have allowed such item(s) in his
Contract Percentage(s) for this and other Sections in the Schedule of Rates under the
Contract.
The Contractor is not entitled to any payment when he fails to remove the Contract
Facilities in accordance with Special Conditions Clause SC01.03(e) of this Section.
LAND TRANSPORT
Measurement of SC01.05 The land transport facilities shall include the provision of petrol private car, electric vehicle
land transport or multi-purpose vehicle (MPV) and the driver services as specified in the Contract.
facilities
The rates for land transport facilities shall be measured each and on a monthly basis for the
period from the date when such land transport facilities are provided for use under the
Contract until the expiry of the Contract Period as specified in the Contract, and any
further period of provision of the land transport facilities that the Maintenance Surveyor
expressly confirms in writing.
01/2
01 CONTRACT FACILITIES AND SPECIAL ATTENDANCES 01
SPECIAL CONDITIONS
LAND TRANSPORT
Measurement of SC01.05 In case where the period of the provision of land transport facilities provided for use is not
land transport (Cont'd) in a whole month, or where no alternative replacement facilities are provided, the rates for
facilities land transport facilities shall be adjusted based on the number of working days basis (over
(Cont'd) the number of calendar days of the given month). The period of the provision of land
transport facilities measured in calendar days shall exclude Saturdays, Sundays and/or
public holidays immediately preceding or following the said period of provision.
No measurement and payment shall be made for any period of time during which there is
no land transport and other alternative replacement facilities is provided for use under the
Contract.
Rates for SC01.06 The rates for land transport facilities shall further include for : -
land transport
facilities (a) Provision of Environment-friendly Petrol Private Cars, Electric Vehicles or Hybrid
Vehicles of not more than one year old, in good working order that is eligible for
reduction of the First Registration Tax. A valid Environment-friendly Vehicle
Certificate shall be provided for Environment-friendly Petrol Private Cars.
(b) Provision of a competent and licensed driver for each vehicle who must have not
less than 3 years' driving experience, no dangerous driving records and who shall
be approved by the Maintenance Surveyor. The driver shall be equipped with a
mobile telephone for contact purpose when on duty.
(c) Provision of the vehicles at all times and for the uses and trips as specified in the
Contract, during normal working hours and such other times when the Contractor
is carrying out work including the time when requested by the Maintenance
Surveyor or his Representatives for emergency situations, or for the discharge of
their duties outside normal working hours and outside such other times when the
Contractor is carrying out work.
(d) Arranging the vehicles to be standby during the period when the vehicles are not
in use including having the vehicles parked at a location designated by the
Maintenance Surveyor.
(e) All tunnels, bridges and cross harbour tunnel toll fees, and parking fees including
the parking fees incurred when the vehicles are standby.
(f) Maintaining a record of the use of the vehicles including details, times and purpose
of journeys together with appropriate pedometer readings and distances travelled.
(g) Maintaining effective comprehensive insurances covering passenger liability of the
vehicles to be driven by any driver. In the case of a private car under the ownership
of the Contractor, inclusion of an endorsement in the insurance policy expanding
the definition to cover the Maintenance Surveyor and his Representatives and all
personnel of the Employer.
01/3
01 CONTRACT FACILITIES AND SPECIAL ATTENDANCES 01
SPECIAL CONDITIONS
LAND TRANSPORT
Rates for SC01.06 (h) Fuels, oils, lubricant and the like for the proper running and functioning of the
land transport (Cont'd) vehicles.
facilities
(Cont'd) (i) Provision for similar alternative transport when the vehicles provided are
unavailable.
(j) Providing or painting the contract number, contract title, the Contractor's name or
other suitable identification as approved by the Maintenance Surveyor to the
vehicles.
CONTRACT EQUIPMENT
Measurement of SC01.07 The rates for provision of contract equipment shall be measured each and on a monthly
contract equipment basis from the date when such equipment is provided for use until the expiry of the Contract
generally Period as specified in the Contract, and any further period of provision of the contract
equipment that the Maintenance Surveyor expressly confirms in writing.
In case where the period of the provision of contract equipment provided for use is not in
a whole month, or where no alternative replacement equipment is provided, the rates for
contract equipment shall be adjusted based on the number of working days basis (over the
total number of calendar days of the given month). The period of the provision of contract
equipment measured in calendar days shall exclude Saturdays, Sundays and/or public
holidays immediately preceding or following the said period of provision.
No measurement and payment shall be made for any period of time during which there is
no contract equipment and other alternative replacement equipment is provided for use
under the Contract.
Rates for SC01.08 The rates for contract equipment shall further include for : -
contract equipment
generally (a) Provision of all equipment with functions, configurations and specifications as
stated in the Contract and in good working order.
(b) Provision of all necessary consumables like paper, toner, etc..
(c) License fees, connection charges, rental charges, service charges, insurance and
the like.
(d) Maintaining monthly report on usage.
(e) Regular maintenance, repair and temporary replacement of the devices of similar
function and configuration during period of repair.
01/4
01 CONTRACT FACILITIES AND SPECIAL ATTENDANCES 01
SPECIAL CONDITIONS
CONTRACT STAFF SERVICES
Measurement of SC01.09 The contract staff services shall include the provision of the following staff services when
contract staff specified in the Contract : -
services
(a) Clerical support staff
(b) Technical officer
(c) Works supervisor (builder's work) and works supervisor
(building services)
(d) Quality control assistant (builder's work) and quality control assistant (building
services)
(e) Repair Call Centre staff
The rates for provisions of contract staff services shall be measured each and on a monthly
basis from the date when the contract staff report duty at the Employer's office until the
expiry of the Contract Period as specified in the Contract, and any further period of
provision of the contract staff services that the Maintenance Surveyor expressly confirms
in writing.
Payment shall only be made when the Contractor has demonstrated to the Maintenance
Surveyor's satisfaction that salary payments have been received by the contract staff.
In case where the contract staff services are not provided in a whole month, or where no
replacement is provided during the period when the contract staff is on leave, the rates for
the contract staff services shall be adjusted based on the number of working days basis
(over the total number of calendar days of the given month). The working period measured
in calendar days shall exclude Saturdays, Sundays and/or public holidays immediately
preceding or following the working period.
No measurement and payment shall be made for the period of time during which there are
no contract staff services provided for use under the Contract.
No measurement and payment shall be made for the period of time during which the
contract staff fails to discharge any of his or her duties to the satisfaction of the Maintenance
Surveyor.
Rates for SC01.10 The rates for "contract staff services" shall further include for : -
contract staff
services (a) Provision of full time contract staff with qualification and experience that meet the
requirements as specified in the Contract.
(b) Performance of all duties.
(c) Maintenance of an attendance diary.
01/5
01 CONTRACT FACILITIES AND SPECIAL ATTENDANCES 01
SPECIAL CONDITIONS
CONTRACT STAFF SERVICES
Rates for SC01.10 (d) All expenses and reimbursement in connection with employment of the contract
contract staff (Cont'd) staff including but not limited to basic salary, contribution to the Mandatory
services Provident Fund, gratuity and all necessary levies, e.g. Construction Industry
(Cont'd) Council, insurances, etc..
(e) Transportation arrangement required for executing their respective duties.
(f) Provision of facilities for executing their respective duties like computer equipment
including both hardware and software, digital cameras, stationery and consumables,
etc..
(g) Working outside normal working hours.
(h) Working on General Holidays, emergency and urgent works and working at
specific locations.
(i) Replacement by temporary staff when the contract staff is on leave.
(j) Any other related costs and expenses that the Contractor may incur from the
recruitment, management and deployment of the contract staff services.
PAYMENT FOR SPECIAL ATTENDANCES
Measurement of SC01.11 The item for Payment for Special Attendances" shall only be measured and paid for when
Payment the Maintenance Surveyor is satisfied that the following conditions have been fulfilled : -
for Special
Attendances (a) Where the work instructed under the Works Order is incidental minor
maintenance and repair work in nature and the claimed value of the works under
the Works Order alone, does not exceed $ 1,000;
(b) Works is carried out to walls or ceiling soffits, where the work is at a clear height
over 10 m high (measured from the level on which the staging or the mean of
access is erected, or where the level is sloping, measured from the level
immediately at the provision of the staging or the mean of access) with no other
means of access available;
(c) Submission of reports and photographic records to justify such reimbursement;
and
(d) The provision of the staging or means of access is made by the Contractor
ownself.
Where works under more than one Works Orders of incidental minor maintenance and
repair nature are carried out at the same location at or around the same period of time by
the Contractor or his Specialist Sub-contractors, the Contractor shall arrange for the full
utilization of the means of access to be provided for these Works Orders. Subject to
fulfillment of the conditions stated in sub-clauses (a) to (d) herein, payment for Special
Attendances will only be made once irrespective of the number of Works Orders issued
under such circumstance.
01/6
01 CONTRACT FACILITIES AND SPECIAL ATTENDANCES 01
SPECIAL CONDITIONS
PAYMENT FOR SPECIAL ATTENDANCES
Measurement of SC01.11 No measurement and payment shall be made for "Payment for Special Attendances" under
Payment (Cont'd) either one of the following conditions : -
for Special
Attendances (i) The claimed value of the works carried out under the above circumstances
(Cont'd) exceeds $ 1,000 per Works Order.
(ii) Where means of access is available or provided at the location by the owners, the
Employer or other parties.
(iii) The Contractor fails to submit the report and photographic records to justify the
reimbursement of the Special Attendances claimed, or the Maintenance Surveyor
considers that the report submitted fails to provide adequate information to
demonstrate satisfaction of the conditions as stated in sub-clauses (a) to (d) herein.
(iv) Where works are carried out under separate Works Order with staging or means
of access provided at the same location at or around the same period of time, and
the estimated value of the works exceeds $1,000 for that Works Order.
Rates for SC01.12 The rates for Payment for Special Attendances shall further include for : -
Payment
for Special (a) Providing any means of access including but not be limited to scaffolding, screens,
Attendances working platforms, staging, gondolas and the like; and erection, subsequent
dismantling and removal of the same upon completion of the works;
(b) Compliance with all safety requirements and certification from independent
checking engineer, where required, and payment of all fees; and
(c) Submission of all necessary records and reports in the format as approved by the
Maintenance Surveyor.
01/7
01 CONTRACT FACILITIES AND SPECIAL ATTENDANCES 01
Item Item
CONTRACT FACILITIES
Note : - The following Items 01001 to 01016 inclusive will only be paid for if the requirements as set out in the
Contract and the conditions as set out in the Special Conditions are complied with.
LAND TRANSPORT
A
Per number-month $
01001 Private car - fully air conditioned saloon car with seating capacity of not less than
five seats (including driver) ........................................................................................................................................................................................................... 22,100.00 01001
01002 MPV - fully air conditioned saloon car with seating capacity of not less than
seven seats (including driver) ........................................................................................................................................................................................................ 23,600.00 01002
CONTRACT EQUIPMENT
A
Per number-month $
01003 Provision of facsimile machine (for A4 size)................................................................................................................................................................................. 110.00 01003
01004 Provision of 3G mobile phone........................................................................................................................................................................................................ 230.00 01004
01005 Provision of computer facilities ..................................................................................................................................................................................................... 250.00 01005
01006 Provision of monochrome laser-jet printer (for A4 size)............................................................................................................................................................... 160.00 01006
01007 Provision of colour inkjet printer (for A3 size).............................................................................................................................................................................. 220.00 01007
01008 Provision of scanner ....................................................................................................................................................................................................................... 110.00 01008
01009 Provision of digital camera ............................................................................................................................................................................................................ 70.00 01009
CONTRACT STAFF SERVICES
A
Per number-month $
01010 Clerical support staff ...................................................................................................................................................................................................................... 11,600.00 01010
01011 Technical officer ............................................................................................................................................................................................................................ 16,000.00 01011
01012 Works supervisor (builder's work) ................................................................................................................................................................................................. 20,500.00 01012
01013 Works supervisor (building services)............................................................................................................................................................................................. 20,500.00 01013
01014 Quality control assistant (builder's work) ...................................................................................................................................................................................... 19,200.00 01014
01015 Quality control assistant (building services).................................................................................................................................................................................. 19,200.00 01015
01016 Repair Call Centre staff ................................................................................................................................................................................................................. 11,600.00 01016
01/8
01 CONTRACT FACILITIES AND SPECIAL ATTENDANCES 01
Item Item
PAYMENT FOR SPECIAL ATTENDANCES
Note : - Item 01017 will only be paid for if the requirements as set out in the Contract and the conditions as set out
in the Special Conditions are complied with.
A
Per item $
01017 Payment for Special Attendances................................................................................................................................................................................................... 3,000.00 01017
01/9
Section 02
DEMOLITION
02 DEMOLITION 02
SECTION 02
DEMOLITION
SPECIAL CONDITIONS
Measurement SC02.01 All demolition works in this Section shall mean the demolition of the whole building or part
generally of concrete or other structures irrespective of storey height including all partitions, fittings,
finishes, services, etc. within the building.
Alteration and repairs other than demolition in this Section shall be measured and paid for
at the appropriate rates under applicable Work Sections of this Schedule including but not
limited to : -
(a) Taking down concrete for Section 04 - Concrete Work
alteration
(b) Taking down brickwork or Section 05 - Brickwork and Blockwork
blockwork walling for
alteration
(c) Taking down rubble walling Section 06 - Masonry
for alteration
(d) Taking down structural Section 10 - Steel and Metal Work
steel for alteration
Measurement SC02.02 Demolition of whole building shall be measured net on the covered floor area of the
of demolition of building to be demolished.
whole building or
part of structures Covered floor area is measured from the outer face of the external walls of a fully covered
structure and measured over all walls, partitions, columns, stair wells, lift wells, escalator
openings, bay windows, covered balconies, pipe/drain/cable ducts, and the like. It
excludes all projections beyond the outer face of external wall and uncovered trafficable
areas such as external playground, landscaped areas and the like.
Demolition of roof shall be measured the overall flat plan area of the roof to be
demolished and will be measured as either one of the following categories : -
(i) Roof in concrete construction (including all structures above roof slab)
of building or structure;
(ii) Roof other than concrete construction (including all structures above roof
slab) of building or structure.
02/1
02 DEMOLITION 02
SPECIAL CONDITIONS
Measurement SC02.02 Roof other than concrete construction refers to structure of timber, steel or other
of demolition of (Cont'd) construction. Measurement of such demolition work shall not apply to structure built on
whole building or top of concrete roof structure of which shall be held to be included under demolition of
part of structures roof in concrete construction.
(Cont'd)
When measuring Demolish and clear away whole building at Ground Floor, cockloft and
the like where access is within the floor shall be measured separately. Break up and clear
away existing slabs on grade, footings, foundations and the like and backfilling voids will
be measured and paid for at the appropriate rates in Section 03 - Excavation of this
Schedule.
When measuring Demolish and clear away cockloft and the like, it shall include area of
staircase or any part of the access.
Removal of asbestos containing materials shall be measured separately.
Measurement SC02.03 Demolition of single storey sheds other than concrete or structural steel encased with
of single concrete structures shall be measured separately. The covered floor area of the single
storey shed storey structure to be demolished shall be measured. The rate shall be inclusive of the
whole structure including roof, all internal structures, fixtures and the like but excluding
slabs on grade which shall be measured in accordance with Special Conditions Clause
SC02.02 of this Section.
Measurement SC02.04 Asbestos containing corrugated sheeting shall be measured flat (not girth on corrugations)
of asbestos over the net area covered. No deduction shall be made for openings not exceeding 1.00 m.
containing Ridges, hips and the like shall be measured the net length times the average height as
corrugated fixed. Sheeting of curved, sloped, circular on plan or vertical shall be measured flat. Taking
sheeting down and clearing away existing metal or wooden framings shall be measured separately.
In case where the whole building will be demolished, no separate measurement for
framing shall be made.
Measurement SC02.05 Asbestos containing plaster shall be measured the net area. An allowance shall be made
of asbestos for walls and ceilings for additional area of moulded or carved work. No deduction shall
containing be made for openings not exceeding 1.00 m.
plaster
Measurement SC02.06 Asbestos containing plaster boards, ceiling tiles, particle boards, etc. and the like shall be
of asbestos measured over the area covered. No deduction shall be made for openings not exceeding
containing 1.00 m. Taking down and clearing away existing metal or wooden framings shall be
plaster measured separately. In case where the whole building will be demolished, no separate
boards, etc. measurement for framing shall be made.
02/2
02 DEMOLITION 02
SPECIAL CONDITIONS
Rates for SC02.07 The rates for demolition of whole building or part of structures shall include for : -
demolition of
whole building (a) Carrying out survey of building or structures prior to demolition and preparation
or part of of record drawings and survey reports where required including taking
structures photographic records and measurements.
(b) Submission of demolition proposals, method statement, sequence of demolition,
all necessary design and calculations for all temporary works, including
certification and endorsement by Registered Structural Engineer for Maintenance
Surveyor's approval before commencing demolition work.
(c) Providing all precautionary and protective measures, scaffolding, canopy, netting,
covering, dust-proof screens, heavy duty protective nettings, warning signs, and
all other measures proposed by the Contractor in the method statement that are
required for the execution of the demolition works.
(d) In addition to Clause GR.10 (n) of Section 00 - General Regulations of this
Schedule, providing all enhanced and heavy duty precautionary protective
measures including propping, shoring, strutting, special covered walkways,
scaffolding, catch fans and platforms, dust-proof screens, heavy duty protective
netting and all other measures proposed by the Contractor in the method
statement that are required for the execution of the demolition work.
(e) Provision of recording the entire demolition process in the form of CCTV of
sufficient number of cameras to be installed at strategic location(s) to be agreed
with the Maintenance Surveyor; and subsequent removal of the same upon
completion of the demolition process.
(f) Plain or reinforced concrete in case of concrete construction
(g) Provision of all necessary safety measures and taking all necessary measures to
minimize nuisance caused by the demolition works to adjoining properties and
occupants, the public in general, passing vehicles and workmen.
(h) Giving notice to relevant utility undertaker(s) or Government departments and
identify utilities that will be affected by the proposed demolition and arranging
utilities undertaker(s) or Government department for disconnection of services.
Disconnecting and sealing utilities, and marking and recording position of sealed
utilities, including liaising with relevant utility undertaker(s) and Government
department.
(i) Taking down and clearing away all structures, finishes, fittings and the like from
the structural floor level.
(j) Watering debris as necessary to reduce dust nuisance to a minimum.
(k) Removing off site all materials, debris and other arisings which shall become the
property of the Contractor, and complying with all relevant regulations and
requirements relating to the sorting and removal etc. of all demolition materials.
02/3
02 DEMOLITION 02
SPECIAL CONDITIONS
Rates for SC02.07 (l) Protecting areas adjacent to demolition works from damages resulting from such
demolition of (Cont'd) demolition.
whole building
or part of (m) Making good to buildings, structures, pavings, etc. and the like caused by the
structures demolition of adjacent building or structure.
(Cont'd)
(n) Provision of settlement monitoring points and reports as required.
(o) Provision of full time safety officer and/or registered professional engineer when
required for the demolition work.
(p) Executing works to comply with statutory requirements.
Rates for SC02.08 The rates for demolition of concrete structural roof shall, in addition to the requirements of
demolition Special Conditions Clause SC02.07, include for : -
of roof
(a) All parapets and rails.
(b) All upper stairs, water tanks and all structures and fittings above roof slab.
Rates for SC02.09 The rates for demolition of roof other than concrete structural roof shall, in addition to the
demolition requirements of Special Conditions Clause SC02.07, include for : -
of roof other
than concrete (a) Cladding, roof covering and all supporting framings, flashings, gutters and the like.
structural roof
(b) All associated features to the roof.
Rates for SC02.10 The rates for removal of asbestos containing materials shall include for : -
removal of
asbestos (a) Works carrying out by an approved Environmental Protection Department (EPD)
containing Registered Asbestos Contractor in compliance with statutory requirements.
materials
(b) All preparation work, air monitoring by approved EPD Registered Asbestos
Laboratory, safety precaution, giving statutory notices, disposal of waste and
other works as required by the Asbestos Abatement Plan or relevant legislation
and codes of practice issued under the Air Pollution Control Ordinance and
Waste Disposal Ordinance.
(c) Carrying out the works in accordance with the Code of Practice on the
Preparation of Asbestos Investigation Reports, Asbestos Management Plans and
Asbestos Abatement Plans.
(d) Provision for taking personal air samples for the worker carrying out asbestos
removal work as specified in the G.S. Item 2.52.
(e) Provision of respirator and protective clothing for use by Maintenance Surveyor's
Representative for inspection of the removal work.
02/4
02 DEMOLITION 02
SPECIAL CONDITIONS
Rates for SC02.10 (f) Where there is no Asbestos Abatement Plan, preparing and submission of a
removal of (Cont'd) method statement of the removal works before commencement of the removal
asbestos works.
containing
materials (g) Removal of asbestos-containing materials using glove bag method.
(Cont'd)
(h) Conducting smoke test by a registered asbestos consultant before
commencement of asbestos removal works to ensure the integrity of the full
containment.
(i) The opening up of pipe duct, etc, to gain access to asbestos containing material,
and the subsequent reinstatement, the making good of disturbed surface and the
application of non-asbestos substitute material.
Rates for SC02.11 The rates for asbestos survey and Asbestos Investigation Report shall include for : -
asbestos
survey (a) Designing, and directing bulk sampling and analysis work. (The work itself by an
approved EPD Registered Asbestos Laboratory is measured separately.)
(b) Carrying out the work in accordance with the Code of Practice on the
Preparation of Asbestos Investigation Reports, Asbestos Management Plans and
Asbestos Abatement Plans.
(c) Providing labelling asbestos containing materials and obtaining endorsement from
Environmental Protection Department on the Report.
Rate for SC02.12 The rate for Asbestos Management Plan shall include preparing an Asbestos Abatement
Asbestos Plan for materials to be removed and an Operation and Maintenance Plan for asbestos
Management containing materials to be retained. The rate shall also include for obtaining endorsement
Plan on the plan from Environmental Protection Department.
Rate for SC02.13 The rate for employing an approved EPD Registered Asbestos Consultant shall include
employing an for : -
approved EPD
Registered (a) Submission of the proposed Registered Asbestos Consultant to the approval of
Asbestos the Maintenance Surveyor.
Consultant
(b) Provision of supervision services of the Asbestos Contractor's work to ensure
that the work is carried out in accordance with the relevant legislation and codes
of practice, and to manage the implementation of the approved Asbestos
Abatement Plan.
(c) Provision of services for revision of the abatement method where necessary.
(d) Liaising and co-ordinating with the Environmental Protection Department.
G.S. clauses SC02.14 G.S. clauses for demolition can be found in Demolition, Site Clearance and Alterations
Section of the General Specification for Building.
02/5
02 DEMOLITION 02
Item Item
DEMOLITION OF WHOLE BUILDING OR PART OF STRUCTURES
Demolish whole building or part of structures in any height including clearing away all materials arising from Site : -
(Note : - The demolition of a whole building or part of structures shall be paid for on a floor-by-floor basis at the rates of
the following Items 02001 to 02008 inclusive )
A
Per square metre $
02001 Ground floor storey of building or structures (excluding slabs on grade)..................................................................................................................................... 675.00 02001
02002 Suspended ground slab or cockloft of building or structures including staircase......................................................................................................................... 282.40 02002
02003 Mezzanine floor of building or structures...................................................................................................................................................................................... 678.90 02003
02004 First to fourth floor of building or structures.................................................................................................................................................................................. 689.20 02004
02005 Additional floor from fifth floor and above (except roof) of building or structures...................................................................................................................... 698.00 02005
02006 Roof (including all structures above roof slab) of building or structures...................................................................................................................................... 732.10 02006
02007 Ditto but other than concrete construction (steel, timber or others construction)......................................................................................................................... 53.10 02007
02008 Single storey shed, building, structure, etc. (other than concrete construction)............................................................................................................................ 105.50 02008
RELATED WORKS FOR REMOVAL OF ASBESTOS CONTAINING MATERIALS
A
Each $
02009 Set up total containment with 3-chamber decontamination unit, maintaining negative air pressure by using HEPA-filtered
appliance throughout the course of asbestos abatement work, and taking down the containment on completion....................................................................... 13,097.70 02009
(The work shall be carried out in accordance with the Asbestos Abatement Plan and the Code of Practice on Asbestos Control
- Asbestos Work Using Full Containment and Mini-containment.)
02010 Set up segregation between asbestos work area and external area using plastic sheets, and decontamination unit and debris
port where specified, taking down the segregation on completion................................................................................................................................................ 11,642.40 02010
(The work shall be carried out in accordance with the Code of Practice on Asbestos Control- Safe Handling of Low Risk
Asbestos Containing Material.)
02011 Carry out bulk sampling of suspected asbestos containing material and conduct examination using polarized light microscopy
method on the presence, content and type of asbestos by an approved EPD Registered Asbestos Laboratory............................................................................ 392.90 02011
.
02012 Carry out further analysis (where the content of asbestos in a bulk sample cannot be determined by polarized light microscopy
method) using point counting method by an approved EPD Registered Asbestos Laboratory..................................................................................................... 2,037.40 02012
02013 Carry out environmental air sampling and analysis to measure the fibre concentration by an approved EPD Registered
Asbestos Laboratory........................................................................................................................................................................................................................ 272.90 02013
02014 Dispose a collection of loose items with asbestos containing materials like fire blankets and bench mats, from one site ......................................................... 2,728.70 02014
(The work shall be carried out in accordance with the Code of Practice on Handling, Transportation and Disposal of
Asbestos Waste.)
02/6
02 DEMOLITION 02
Item Item
REMOVAL OF ASBESTOS CONTAINING MATERIALS
A
Each $
02015 Take down and clear away asbestos containing fire-stopping material around electric cable running through wall and floor................................................... 1,819.10 02015
02016 Take down and clear away asbestos containing gasket and flexible joint in air duct of any size................................................................................................. 1,819.10 02016
02017 Take down and clear away asbestos containing arc chute in electric switch box, including attendance by a qualified electrician............................................ 873.20 02017
Per square metre
02018 Take down and clear away from Site asbestos containing roof insulation tiles............................................................................................................................ 240.10 02018
02019 Ditto but asbestos containing corrugated or flat cement sheets fixed to a metal or timber frame................................................................................................ 174.60 02019
02020 Ditto but asbestos containing plaster.............................................................................................................................................................................................. 385.70 02020
02021 Ditto but asbestos containing plaster boards, chalkboards, particle boards, etc. and the like fixed to wall or other structure.................................................... 185.60 02021
02022 Ditto but asbestos containing vinyl tile and tile adhesive by low VOC mastic remover,
including degreasing agent if any as recommended by manufacturer........................................................................................................................................... 207.40 02022
02023 Ditto but asbestos containing vinyl tile and adhesive including existing cement sand screeding................................................................................................ 174.60 02023
02024 Ditto but asbestos containing cement grille block wall and cement panel wall............................................................................................................................ 247.40 02024
02025 Ditto but asbestos containing insulation on calorifier or other surfaces........................................................................................................................................ 618.50 02025
Per linear metre
02026 Take down and clear away from Site asbestos containing refuse chutes of any sizes................................................................................................................... 2,401.30 02026
02027 Ditto but asbestos containing lagging or in-situ and pre-moulded insulation to pipework of any sizes....................................................................................... 1,746.40 02027
02028 Ditto but asbestos containing pipe or drain of any size.................................................................................................................................................................. 1,418.90 02028
ASBESTOS SURVEY
A
Per item $
02029 Carry out asbestos survey for total floor area n.e. 200 m of a building or structure and prepare an Asbestos Investigation Report
by an approved EPD Registered Asbestos Consultant .................................................................................................................................................................. 7,640.30 02029
02030 Ditto but for total floor area 200 - 1,200 m of a building or structure.......................................................................................................................................... 17,099.80 02030
02031 Extra over Item 02030 for each additional 200 m or part thereof in total floor area of a building or structure in excess of 1,200 m
of a building or structure................................................................................................................................................................................................................. 1,891.90 02031
02/7
02 DEMOLITION 02
Item Item
ASBESTOS MANAGEMENT PLAN
A
Per item $
02032 Prepare an Asbestos Management Plan by an approved EPD Registered Asbestos Consultant on premises where an Asbestos
Investigation Report is already available ....................................................................................................................................................................................... 5,457.40 02032
02033 Employ an approved EPD Registered Asbestos Consultant to manage the implementation of an Asbestos Abatement Plan. .................................................. 21,829.50 02033
(Note: This item will only be paid for, if ordered by the Maintenance Surveyor in writing.)
02/8
Section 03
EXCAVATION
03 EXCAVATION 03
SECTION 03
EXCAVATION
SPECIAL CONDITIONS
Measurement SC03.01 Excavation shall be measured net with no increase for working space or bulkage of material,
generally allowance for both having been made in the rates. Blasting will not be permitted.
Should occasion ever occur when blasting is permitted, no adjustment will be made to the
rates in this Schedule.
Where excavation oversite to areas exceeds an average of 200 mm deep, it shall be measured
as reduced level excavation from existing ground level (i.e. no top soil or surface excavation
item shall first be measured). Trench for foundation, manholes, etc. and other excavation items
shall be measured from the reduced levels or ground levels, whichever is the lower.
The definitions of trench excavation and bulk excavation shall be in accordance with
G.S. Item 3.01(x) and (xi).
Excavation for pipes and cables shall be measured to the nearest 0.25 m average depth.
When measuring Extra over pipe trench excavation for excavating in brickwork,
concrete, solid rock etc., the net width of trench excavation measured shall be in
accordance with Table B3.4.2 in the Specification for Plumbing and Drainage
Installation adopted in the Contract.
Measurements for spreading or removal of spoil arising from the Contractor's excavation
shall be made net on the basis of the solid contents before excavation and no allowance
shall be made for increase in bulk. Where the spoil to be removed has not been excavated
by the Contractor, as in the case of landslips, debris or rubbish, etc., the actual cubic
contents shall be measured.
Soil, hardcore, granular or graded granular filling items shall be measured net after
completion.
Measurement of SC03.02 Throughout this Schedule, rates for all Sections shall include for all temporary preventive,
steel sheet piling protective and supporting measures to the faces of excavation. No payment will be made
for steel sheet piling and the likes under any circumstances, except where specifically
ordered by the Maintenance Surveyor in writing.
Steel sheet piling including non-standard make up piles shall be measured net on the area
of the piling driven. The measurement of the calculated weight shall be the length along the
centre line of the alignment of completed sheet pile multiplied by the average depth from
the ground level or reduced level, whichever the lower to the toe edge of the pile driven.
03/1
03 EXCAVATION 03
SPECIAL CONDITIONS
Measurement of SC03.02 Extra over for corner piles and junction piles shall be the net length measured from the
steel sheet piling (Cont'd) ground level or reduced level, whichever is the lower, to the toe edge of the piles driven.
(Cont'd)
The measurement of burning off the tops of steel piles shall be the length along the centre
line of the alignment of piles driven. This item will only be paid for, if ordered by the
Maintenance Surveyor in writing.
All temporary strutting and shoring to sheet piling including waling, strutting, bracing, posts
and connecting members shall be found in Section 10 - Steel and Metal Work of this
Schedule.
Measurement of SC03.03 The measurement shall be the compacted thickness as specified by the Maintenance
earth, granular Surveyor, whether laid in one or more layers. No deduction shall be made for voids not
and hardcore exceeding 1.00 m.
filling
Measurement of SC03.04 Filter membrane shall be measured as the surface area of the face to be covered and no
filter membrane allowance shall be made for surface irregularities or other local peculiarities. No deduction
shall be made for an area not exceeding 1.00 m.
Rates for SC03.05 The rates for all excavation items shall include for : -
excavation items
(a) Mobilization, maintenance and demobilization of excavator, roller, compaction
plant, moving plant and the like.
(b) Allowance for working space and increase in bulk of all materials arising from
excavation, down taking, alteration or demolition.
(c) Excavating in any type of level or sloping ground encountered including earth,
clay, sand, gravel, loose boulders not exceeding 0.20 m, etc. (Note : - Extra for
excavating in solid rockas defined in Special Conditions Clause SC03.09 herein
below, will be paid in addition).
(d) Setting out the work and all profiles, rods, etc., and work straight or circular on
plan.
(e) Cutting down shrubs, undergrowth, etc., including trees not exceeding 95 mm
diameter at breast height, grubbing up roots and clearing away.
(f) Removing old drains and sealing off connections.
(g) Getting out excavated material by any means necessary and deposit excavated
material in heaps including multi-handling within Site area.
03/2
03 EXCAVATION 03
SPECIAL CONDITIONS
Rates for SC03.05 (h) Keeping excavations free from water by baling, pumping, temporary diversion
excavation items (Cont'd) channels or other means. All contaminated water arising from excavation shall be
(Cont'd) treated in accordance with the requirements of Environmental Protection
Department (EPD) before disposing into the public drainage system. All
additional expenses incurred shall be included in the rates.
(i) Trimming sides, vertical or battered as required, and trimming, levelling, grading
and ramming bottoms, and trimming slopes and banks.
(j) Protecting the exposed surfaces of excavation by any means necessary.
(k) Strutting, shoring, supporting and protecting measures for the faces of excavation.
(Note : - Timbering/Steel works required to be left-in shall be paid for, if ordered
by the Maintenance Surveyor in writing, at the rates contained in Section 08 -
Carpentry and Joinery and Section 10 - Steel and Metal Work of this Schedule.)
(l) Steel plates or other approved coverings to trenches or pits where required to
provide crossings for pedestrian and vehicular traffic, shall comply with all
regulations and requirements including providing traffic lights, warning lights, signs
etc. and payment of all charges incurred.
(m) All multi-handling and temporary spoil heaps, on or off-site between excavation
and final position.
(n) Temporarily supporting drain pipes, cables, etc., during excavation and making
good any damage that may be caused to the same.
(o) Filling with concrete or backfilling and compacting strictly in accordance with
G.S. to over excavation areas or as a result of the Contractor's proposed
method of excavation or where additional concrete is placed in lieu of trimming
rock bottoms to exact level.
(p) Making good with lean concrete any surface irregularities under the formation of
rock cuttings which remain after trimming of rock excavation.
(q) Preparation of record survey including an over Site topographical survey by a
registered surveyor when ordered by the Maintenance Surveyor in writing.
(r) Design of Temporary Works associated with earthworks, including temporary
slopes, stockpiles and drainage by Registered Structural Engineers. Submit the
design and calculations of the Temporary Works for the approval of the
Maintenance Surveyor. Prepare and submit method statement for the erection
and removal of Temporary Works as required.
(s) Settlement monitoring points.
03/3
03 EXCAVATION 03
SPECIAL CONDITIONS
Rates for Extra SC03.06 The rates for Extra for excavating in brickwork, concrete, solid rock, etc. shall further
for excavating include for trimming the faces or edges of the work remaining.
in brickwork,
concrete, etc.
Rates for soil SC03.07 The rates for soil filling and removal shall further include for all multi-handling to final
filling and position.
removal
Rates for soil, SC03.08 The rates for all soil, hardcore, granular and graded granular filling items shall further
hardcore, include for : -
granular and
graded granular (a) Mobilization, maintenance and demobilization of earth moving plant, rollers,
filling compaction plant and other plant necessary for the works.
(b) Deposition and compaction including compaction in layers to the required density.
(c) Finishing surfaces level or to falls, gradients, crowns and cambers to exact profile
required, with each successive surface finished parallel to the final finished surface.
(d) Additional bulk of material required to allow for compaction and consolidation.
(e) All wheeling and multi-handling of material from temporary spoil heaps to place of
final incorporation in the work.
(f) Forming and trimming banks and slopes.
(g) Temporary retaining boards to edges and slopes and any necessary handpacking
at stepping and the like.
(h) Removing, replacing or making good placed or compacted filling material as
required where filling material subsequently becomes damaged or unsuitable.
(i) Protecting the exposed surfaces of filling by any means necessary.
(j) Keeping and maintaining the exposed surfaces clean.
(k) Preparation of record survey when ordered by the Maintenance Surveyor in
writing.
03/4
03 EXCAVATION 03
SPECIAL CONDITIONS
Rates for soil, SC03.08 (l) Soil tests and in-situ tests including : -
hardcore, (Cont'd)
granular and (i) Collect samples selected by the Maintenance Surveyor.
graded granular
filling (ii) Carrying out all tests of soil samples by the personnel of an approved
(Cont'd) independent firm using their own equipment and providing such labour
and assistance as may be required.
(iii) Preparation of test reports.
(iv) Payment of all charges incurred.
Rates for rock SC03.09 Solid rock shall be defined as Rock, which in the opinion of the Maintenance Surveyor
excavation can only be excavated by means of wedging and splitting, the use of pneumatic tools or
stitch core, cut, drill, core hydraulic splitter, and shall only be allowed when the net
quantity to be actually cut, split and excavated in any isolated individual portion exceeds
0.20 m, except that in the case of excavating post holes the net quantity excavated shall
be paid for. For the purposes of this Schedule, excavation in solid rock has been
assumed based on excavation by hand or with tools. Should occasion ever occur when
blasting is permitted, no adjustment will be made to these rates but the Contractor shall
submit method statement for approval, provide blast screens as necessary and take all
other precautions and make good any damage caused at his own expense.
Brick, concrete, SC03.10 Any brick, concrete, rock, etc., arising from the excavations shall become the property of
rock, etc., to the Contractor, and may if required, and approved by the Maintenance Surveyor, be
become property broken and used for hardcore filling. For the purposes of removal, these materials shall be
of the Contractor paid for as ordinary soils but if they are subsequently used as hardcore filling on the Site,
no removal from the Site will be measured.
Rates for steel SC03.11 The rates for steel sheet piling shall further include for : -
sheet piling
(a) Welding, jointing and splicing.
(b) Fabrication of non-standard make up piles.
(c) Initial trenching and guide frames.
(d) Temporary strutting and waling for driving.
(e) Preparing and submitting details and drawings with method statement all in
accordance with G.S. Items 4.02, 4.03, 4.04, 4.06, 4.07, 4.08, 4.15 and 4.16
and by Registered Structural Engineer if required.
03/5
03 EXCAVATION 03
SPECIAL CONDITIONS
Rates for steel SC03.11 (f) Additional work and cost related to obstructions in accordance with G.S. Items
sheet piling (Cont'd) 4.12 and 4.13.
(Cont'd)
(g) Preparing and applying protective coating or other surface treatment to sheet pile.
(h) Extraction of sheet piles.
(i) Left-in position sheet pile when ordered by the Maintenance Surveyor in writing.
Rates for SC03.12 The rates for burning off tops of sheet pile shall further include for : -
burning off
tops of sheet (a) Provision, maintenance and removal from Site tools and equipment necessary for
pile the works.
(b) Disposal of surplus length of piles.
(c) Cleaning the affected area and applying protective coatings or other surface
treatment.
Payment for SC03.13 For payment purpose, the lump sum fee payment for Utility Connection And Pavement
"Utility Connection Works shall not be payable, unless the Contractor has demonstrated and substantiated
And Pavement by :
Works"
(a) A copy of successfully granted Excavation Permit for the work.
(b) Relevant approval forms and drawings from utility companies or Government
departments.
(c) Contractor's prior written notice to the Maintenance Surveyor of the name of the
specialist contractors employed for the Utility Connection And Pavement Works
when the Contractor is not included in the relevant List of Approved Contractors
for Public Works to carry out the Utility Connection And Pavement Works.
Specification for SC03.14 Specification for drain trench excavation can be found in the Specification for Plumbing
drain trench and Drainage Installation adopted in the Contract.
excavation
G.S. clauses for SC03.15 G.S. clauses for steel sheet piling can be found in Steel Sheet Piling Work Section of the
steel sheet piling General Specification for Building.
03/6
03 EXCAVATION 03
Item Item
STEEL SHEET PILING TO EXCAVATION
Plant : -
A
Per item $
03001 Mobilization, maintenance and demobilization of piling plant, crane, compressor and other equipment necessary for the work.............................................. 19,373.30 03001
Supplying, handling, transporting, pitching, driving and withdrawing / left in sheet piles as G.S. Item 4.01 : - Design length (m)
n.e. 10 10 - 20 20 - 30
A B C
Per kg $ $ $
03002 Steel sheet piles........................................................................................................................................................................................... 7.20 7.90 8.20 03002
A
Per linear metre $
03003 Extra over Item 03002 for corner piles........................................................................................................................................................................................... 698.20 03003
03004 Extra over Item 03002 for junction piles........................................................................................................................................................................................ 698.20 03004
Sundries : -
Per linear metre
03005 Burning off tops of sheet piles........................................................................................................................................................................................................ 220.50 03005
Diameter (mm)
n.e. 100 100 - 200 200 - 300 300 - 400 400 - 500
A B C D E
Each $ $ $ $ $
03006 Cutting or burning holes through sheet piling........................................................................................................ 44.50 89.00 133.40 201.00 245.50 03006
(Note : - The above Items 03001 to 03006 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing)
03/7
03 EXCAVATION 03
Item Item
GENERAL EXCAVATION
A
Per square metre $
03007 Excavate over Site n.e. 200 mm deep............................................................................................................................................................................................. 28.70 03007
Per cubic metre
03008 Excavate over Site to reduce levels average exceeding 200 mm deep.......................................................................................................................................... 165.60 03008
That portion of excavation
n.e. 1.50 - 3.00 - 4.50 -
1.50 m 3.00 m 4.50 m 6.00 m
deep deep deep deep
A B C D
Per cubic metre $ $ $ $
03009 Excavate trenches for foundation.............................................................................................................................................. 179.80 201.30 224.10 323.90 03009
03010 Excavate for foundations, manholes, pits, cesspits, etc., and the like...................................................................................... 182.50 210.10 259.00 394.50 03010
A
Each $
03011 Excavate for post holes n.e. 0.30 m including return, fill in and compact and remove surplus excavated material from Site................................................... 96.20 03011
03/8
03 EXCAVATION 03
Item Item
PIPE OR CABLE TRENCH EXCAVATION
Excavate trench for pipe or cable with Pipe bore or cable diameter (mm)
concrete bed (if any), including return, Two Three
fill in, compact and remove surplus Not 150 300 450 600 900 1,200 1,500 pipes pipes
excavated material from Site : - exceeding to to to to to to to side by side by
150 300 450 600 900 1,200 1,500 1,800 side each side each
n.e. 150 n.e. 150
A B C D E F G H I J
Per linear metre $ $ $ $ $ $ $ $ $ $
03012 Trench n.e. 1.50 m deep
and average 0.25 m deep............................................... 21.20 31.00 - - - - - - 32.50 43.70 03012
03013 Ditto average 0.50 m deep............................................. 38.50 55.80 75.80 104.00 - - - - 59.30 80.10 03013
03014 Ditto average 0.75 m deep............................................. 58.50 75.50 100.80 137.10 178.10 - - - 83.10 111.90 03014
03015 Ditto average 1.00 m deep............................................. 85.50 99.00 125.80 164.10 212.10 276.20 - - 107.00 143.80 03015
03016 Ditto average 1.25 m deep............................................. 107.90 128.80 154.50 191.60 250.20 326.40 398.10 - 139.80 171.70 03016
03017 Ditto average 1.50 m deep............................................. 128.50 152.30 181.80 224.70 290.40 375.50 454.00 537.40 152.10 186.00 03017
03018 Trench 1.50 - 3.00 m deep
and average 1.75 m deep............................................... 150.00 176.70 210.30 259.30 332.60 427.30 513.10 603.10 193.70 237.30 03018
03019 Ditto average 2.00 m deep............................................. 171.70 201.40 239.20 294.30 375.50 480.20 573.00 669.90 219.30 268.60 03019
03020 Ditto average 2.25 m deep............................................. 197.20 230.20 272.00 333.60 422.80 537.30 637.50 741.40 255.50 311.56 03020
03021 Ditto average 2.50 m deep............................................. 226.70 263.00 309.10 377.20 474.10 599.10 707.00 817.70 289.40 352.00 03021
03022 Ditto average 2.75 m deep............................................. 249.10 288.70 339.20 413.70 519.00 654.20 769.80 877.60 318.20 387.50 03022
03023 Ditto average 3.00 m deep............................................. 272.00 314.90 370.10 451.50 565.30 711.60 835.10 960.30 348.20 424.20 03023
03024 Trench 3.00 - 4.50 m deep
and average 3.25 m deep............................................... 302.70 349.00 408.80 497.20 620.00 777.00 908.70 1,041.60 385.60 468.70 03024
03025 Ditto average 3.50 m deep............................................. 326.20 376.00 440.80 536.30 668.00 836.40 976.40 1,117.00 416.30 506.70 03025
03026 Ditto average 3.75 m deep............................................. 350.00 403.70 473.10 575.90 716.60 896.80 1,045.30 1,193.90 447.60 545.20 03026
03027 Ditto average 4.00 m deep............................................. 377.70 435.10 509.50 619.80 770.00 961.80 1,119.00 1,275.70 482.70 587.70 03027
03028 Ditto average 4.25 m deep............................................. 402.20 463.30 542.90 660.60 820.30 1,024.20 1,190.20 1,355.00 514.80 627.40 03028
03029 Ditto average 4.50 m deep............................................. 431.00 496.20 581.00 707.10 876.60 1,093.10 1,268.50 1,441.90 551.70 672.20 03029
03/9
03 EXCAVATION 03
Item Item
EXCAVATING IN BRICKWORK, CONCRETE, ROCK, ETC.
A
Per cubic metre $
03030 Extra over either of Items 03007 to 03029 inclusive for excavating in chunam surfacing, cement rendering, masonry,
brickwork, blockwork, bituminous surfacing, etc. and the like..................................................................................................................................................... 39.20 03030
03031 Ditto for excavating in plain concrete foundations, surface beds, etc........................................................................................................................................... 137.70 03031
03032 Ditto for excavating in reinforced concrete foundations, surface beds, etc., including cutting reinforcement............................................................................ 232.90 03032
03033 Ditto for excavating in solid rock as described in Special Conditions Clause SC03.09............................................................................................................... 281.10 03033
03034 Ditto for excavating in solid rock with non-explosive demolition agent....................................................................................................................................... 441.10 03034
(Note : - This item will only be paid for, if ordered by the Maintenance Surveyor in writing.)
SOIL FILLING
A
Per cubic metre $
03035 Return, fill in and compact suitable excavated materials around foundations, etc., and the like................................................................................................. 39.60 03035
03036 Wheel, spread, level and compact suitable excavated materials in layers as filling to make up level.......................................................................................... 38.60 03036
03037 Approved suitable filling materials including both general filling material or special filling material as G.S.
Items 3.01(vii) and (viii) brought to Site from Contractor's own source, wheel, spread, level and compact
in layers as filling around foundations, etc. and the like................................................................................................................................................................ 98.80 03037
03038 Ditto but as filling to make up level............................................................................................................................................................................................... 87.50 03038
(Note : - The above Items 03037 to 03038 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
REMOVAL
A
Per cubic metre $
03039 Load surplus or unsuitable excavated material and remove from Site.......................................................................................................................................... 149.40 03039
03040 Load spoil, debris, rubbish, etc., and the like not arising from the works and remove from Site................................................................................................. 165.40 03040
(Note : - This item will only be paid for, if ordered by the Maintenance Surveyor in writing and the quantity agreed
before removal commences)
GRANULAR FILLING
A
Per cubic metre $
03041 Wheel, spread, level and compact sand / fine aggregate in layers including blinding top surface with approved fine grade
material............................................................................................................................................................................................................................................ 131.00 03041
03042 Wheel, spread, level and compact granular filling of size 75 - 150 mm coarse aggregate in layers including blinding top
surface with approved fine grade material..................................................................................................................................................................................... 180.40 03042
03043 Ditto but filling behind retaining walls.......................................................................................................................................................................................... 190.20 03043
03/10
03 EXCAVATION 03
Item Item
HARDCORE FILLING
Hardcore size : 28 - 150 mm in single or multi-graded size(s)
A
Per cubic metre $
03044 Wheel, spread, level and compact hardcore in beds under floors, pavings, etc., and the like in layers n.e. 150 mm thick
including blind top surface with approved fine grade material..................................................................................................................................................... 249.40 03044
03045 Ditto but in layers filled in behind retaining walls including hand packing where necessary...................................................................................................... 260.80 03045
FILTER MEMBRANE
Supply and lay thermally bonded non-woven filter membrane complying with the following specification : -
A
Per square metre $
03046 Filter membrane with pore size300m; permeability (at 5cm head)150 l/m.s; wide width strip tensile
strength 3.0 kN/m........................................................................................................................................................................................................................ 15.80 03046
03047 Ditto but with pore size180m; permeability (at 5cm head)130 l/m.s; wide width strip tensile strength 6.0 kN/m...................................................... 17.40 03047
03048 Ditto but with pore size150m; permeability (at 5cm head)100 l/m.s; wide width strip tensile strength 8.0 kN/m...................................................... 21.10 03048
03049 Ditto but with pore size125m; permeability (at 5cm head)75 l/m.s; wide width strip tensile strength 12.5 kN/m...................................................... 23.10 03049
03050 Ditto but with pore size110m; permeability (at 5cm head)65 l/m.s; wide width strip tensile strength 14.5 kN/m...................................................... 28.00 03050
MISCELLANEOUS ITEMS
A
Per linear metre $
03051 Clear and clean out mud, debris and the like from rainwater channel, earth ditch and/or culvert with waterway in sectional area
n.e. 0.10 m including raising and afterward replacing any channel cover, cutting back any vegetation alongside and removing
all debris from Site.......................................................................................................................................................................................................................... 6.40 03051
03052 Ditto but 0.10 to 0.20 m................................................................................................................................................................................................................. 9.60 03052
03053 Add to Item 03052 for each additional 0.10 m or part thereof sectional area.............................................................................................................................. 1.90 03053
03054 Clean out eaves gutter at any height and removing all debris from Site........................................................................................................................................ 3.80 03054
(Note : - This item will not be paid for if the gutter is required to be painted)
03/11
03 EXCAVATION 03
Item Item
MISCELLANEOUS ITEMS (CONT'D)
A
Each $
03055 Clear out mud, vegetation, debris and the like from weep hole approximately 600 mm deep from slopes, retaining walls, etc.
and removing all debris from Site................................................................................................................................................................................................... 3.80 03055
03056 Rod out, clear and clean choked drain run including trap, gully, or manhole at either end, raising and afterward replacing any
covers and removing all debris from Site....................................................................................................................................................................................... 61.60 03056
03057 Ditto but choked soil, waste or rainwater down pipe including heads, bends and other fittings.................................................................................................. 62.70 03057
03058 Ditto but choked trap or soil or waste branch pipe to bath, W.C., basin, sink and other sanitary fittings.................................................................................... 32.20 03058
03059 Clear out mud, vegetation, debris and the like from catch pit n.e. 0.30 m internally, raising and afterward replacing any
covers and removing all debris from Site....................................................................................................................................................................................... 43.80 03059
03060 Add to Item 03059 for each additional 0.15 m or part thereof internally..................................................................................................................................... 19.10 03060
03061 Supply sackcloth or nylon sandbag n.e. 0.10 m and excavate ordinary dry earth free from stones, etc., on Site and filled bag with
dry earth or clean sand either from Site or from Contractor's own source and place in position.................................................................................................. 19.10 03061
03062 Add to Item 03061 for mixing 10% cement with the dry earth or sand before filling into the bag.............................................................................................. 6.10 03062
UTILITY CONNECTION AND PAVEMENT WORKS
(Note : - The following Item 03063 will only be paid for, if ordered by the Maintenance Surveyor in writing.)
A
Per item $
03063 Lump sum fee for Utility Connection And Pavement Works........................................................................................................................................................ 8,000.00 03063
03/12
Section 04
CONCRETE WORK
04 CONCRETE WORK 04
SECTION 04
CONCRETE WORK
SPECIAL CONDITIONS
Measurement of SC04.01 Concrete shall be measured net as laid or cast.
concrete
No deduction shall be made for : -
(a) Voids not exceeding 0.05 m.
(b) The volume of reinforcement, steel joists, stanchions and the like cast in.
(c) Openings in walls, floors, roof slabs and the like not exceeding 0.10 m.
Measurement of SC04.02 Measurements of cutting and taking down existing concrete shall include the thickness of
cutting and taking any plastering, rendering or other finish on the surface of concrete.
down existing
concrete The items contained in this Section shall only apply to alterations. Any demolition works
with respect to whole or part of a building shall be measured separately and paid for at
appropriate rates under Section 02 - Demolition of this Schedule.
Measurement of SC04.03 Formwork shall be measured as the actual surface in contact with concrete. No deduction
formwork shall be made for openings not exceeding 1.00 m. Boxing for opening exceeding 1.00 m
shall be measured as edges. Wrot formwork shall be measured only when a fair finished
face to the concrete is specifically ordered by the Maintenance Surveyor in writing.
Measurement of SC04.04 Reinforcement shall be measured net as fixed. No allowance shall be made in the weight
reinforcement for rolling margin. The weight of reinforcement shall be calculated in accordance with the
weight per linear metre in Table 7 of Annex 'C' - Tables of Metal Weights, etc. to this
Schedule (regardless of the actual weight).
Fabric reinforcement shall be measured the net area covered excluding laps. No deduction
shall be made for openings not exceeding 1.00 m.
Measurement of SC04.05 Underlays shall be measured net as laid excluding laps. No deduction shall be made for
underlays openings not exceeding 1.00 m.
Measurement of SC04.06 Precast concrete shall be measured the actual size of the item casted. Any plasterwork
precast concrete shall be excluded in the measurement and it will be separately measured and paid for at
appropriate rates under relevant Sections of this Schedule.
04/1
04 CONCRETE WORK 04
SPECIAL CONDITIONS
Rates for SC04.07 The rates for all concrete shall generally include for : -
concrete
generally (a) Mobilization, maintenance and demobilization of concrete mixer, tower crane,
mobile crane, hoist, concrete pump, vibrator and other plant necessary for the
works.
(b) Conveying, lowering, hoisting, pumping, placing in position, compacting with
vibrator, curing and protection.
(c) Formwork to sides or edges of plain concrete.
(d) Construction joints including formwork, water bars and waterstops.
(e) Laying beds level or to falls, and laying beds or slabs in alternative bays including
necessary formwork to joints between bays.
(f) Finishing surfaces level or to falls, currents and cambers as required, and to
receive pavings unless otherwise specifically stated.
(g) Casting kickers monolithically with base slab where these are required at base of
walls and columns.
(h) Forming all necessary sinkings in or handpacking of hardcore.
(i) Forming or cutting all chases, grooves, notches, rebates, mortices, holes, grouting
in ends with cement mortar including making good to match existing.
(j) Forming all angles, ends, junctions, intersections, outlets and similar labours to
curbs, channels and the like.
(k) Casting in, building in and grouting in work to concrete inserts, puddle flanges,
water stops, ducts and pipes, bolts and cramps, dowels, baluster ends and the
like and making good.
(l) Giving adequate notice to the Maintenance Surveyor to permit inspection of
relevant part of the structure before concrete is placed and prior to commencing
concreting after approval has been obtained from the Maintenance Surveyor.
(m) Submission of samples and testing of materials before trial mix or making concrete
for use in the works.
(n) Carrying out trial mixes, sampling and testing on the same.
(o) Carrying out tests including making concrete cubes and testing on the same
including all necessary security handling of concrete cube.
04/2
04 CONCRETE WORK 04
SPECIAL CONDITIONS
Rates for SC04.07 (p) Sampling of fresh concrete and finished concrete including taking core samples as
concrete (Cont'd) required from the finished concrete works and tests on the same including all
generally necessary security handling of core samples.
(Cont'd)
(q) Filling core hole, tie bar holes with cement mortar or concrete of same strength to
the parent concrete and making good.
(r) Providing method statement for the replacement of condemned concrete and any
remedial works which may be supervised by a Registered Structural Engineer.
(s) All labours and equipment required at the specified locations including any
necessary hoisting, craneage, scaffolding and temporary platforms, etc. for
making test cores.
(t) Removing from Site any concrete work failed to conform to the Specification.
(u) Recording and submitting records for ready-mixed concrete.
(v) Submitting details of mix design.
(w) Control of alkali-aggregate reaction in concrete.
(x) Use of recycled aggregate and/or recycled water in concrete, when required.
Rates for SC04.08 The rates for plain concrete shall further include for : -
plain concrete
(a) Erecting, maintaining and removing formwork or falsework as required.
(b) Additional volume of concrete for filling over-break or working space.
Rates for SC04.09 The rates for reinforced concrete shall further include for :-
reinforced
concrete (a) Tamping around reinforcement.
Rates for SC04.10 The rates for reinforcement shall include for : -
reinforcement
(a) Cleaning, cutting to length, bending (including cranks and hooked ends), hoisting,
fixing and securely supporting in the required position.
(b) Plastic cover spacers, spacer blocks, steel spacer rods, steel clips, steel chairs
and annealed iron tying wire or tack welding.
04/3
04 CONCRETE WORK 04
SPECIAL CONDITIONS
Rates for SC04.10 (c) All requirements of sampling and testing including security handling, stock
reinforcement (Cont'd) management on Site and removal of non-compliant re-bars.
(Cont'd)
(d) Extra fabric reinforcement at laps.
(e) Provision of all types of test certificates.
(f) Submission of bar bending schedule.
Rates for SC04.11 The rates for epoxy coating to reinforcement shall further include for compliance with the
epoxy Specification.
coating to
reinforcement
Rates for SC04.12 The rates for formwork shall include for : -
formwork
(a) Submission of design on formwork and falsework including supports and foundations,
and where required, by a Registered Structural Engineer.
(b) Erecting, maintaining and striking formwork and falsework.
(c) Preventing loss of grout between joints.
(d) Fixing inserts and chases.
(e) Boxing out to form holes not exceeding 1.00 m.
(f) Preparing and applying surface retarders and release agents as required.
(g) Multi-handling of removing formwork and falsework when striking without
overloading the finished concrete work.
(h) Preparing and applying wood preservatives to all surfaces of left-in timber formwork.
(i) Forming cambers and falls.
(j) Individual fillets, chambers, splays, drips, rebates, recesses, grooves and the like,
not exceeding 100 mm total girth measured on the faces in contact with the concrete.
(k) Strutting to soffits at any height.
(l) Soffits of solid slabs in any thickness.
(m) Sides and soffits of beams in any depth.
(n) In case of formwork materials proposed by the Contractor, all necessary
preparation work other than spatterdash.
04/4
04 CONCRETE WORK 04
SPECIAL CONDITIONS
Rates for SC04.13 The rates for precast concrete items shall include for : -
precast
concrete (a) Conveying, lowering, hoisting and multi-handling within the Site or other locations
as required.
(b) All moulds, formwork, etc. including chamfers, throats, weathering, splayed
edges, rounded tops and the like.
(c) Fixing or laying, jointing and pointing in position including cement mortar.
(d) Providing and fixing of steel reinforcement.
Rates for SC04.14 The rates for surface treatment to concrete surface shall include for : -
surface
treatment (a) Preparing plastered or unplastered surfaces ready to receive surface treatment
to concrete including making good cracks with cement mortar.
(b) Cleaning grease or other contaminations.
(c) Forming fillets with cement mortar at junction between slabs and walls.
(d) Carrying out the works all in accordance with the manufacturer's
instructions.
Rates for SC04.15 The rates for cutting and taking down existing concrete shall include for : -
cutting and
taking down (a) Cutting, saw cutting, taking down and clearing away existing concrete by hand or
existing mechanical plant or both.
concrete
(b) Providing all necessary supports, props, struts and shores during taking down
period or until the stability of the affected works is approved by the Maintenance
Surveyor.
(c) Providing all necessary protection as required.
(d) Trimming, bending, straightening and cleaning of reinforcement for connection of
new reinforcement as required.
(e) Providing keys for bonding of new surface.
(f) Preparing and applying bonding agent or primer as required.
(g) Making good all structures, surfaces and finishings disturbed to match existing.
(h) Submission of method statements for approval.
(i) Submission of records as required.
04/5
04 CONCRETE WORK 04
SPECIAL CONDITIONS
Rates for SC04.16 The rates for cutting chases, sinking, grooves, holes and the like shall include for : -
cutting chases,
sinking, etc. (a) Cutting and clearing away from Site existing concrete by hand or mechanical plant
or both.
(b) Making good all structures, surfaces and finishings disturbed to match existing.
Rates for SC04.17 The rates for diamond coring to existing concrete shall include for : -
diamond coring
to existing (a) Mobilization, maintenance and demobilization of coring plant and other
concrete mechanical plants necessary for the works.
(b) Coring through existing concrete or reinforced concrete walls, floors, slabs, roofs
and the like including any finishes.
(c) Providing temporary water and power supplies and working platform as required.
(d) Making good all structures, surfaces and finishings disturbed to match existing.
(e) Clearing away all debris arose.
Rates for SC04.18 The rates for underlay shall include for : -
underlay
(a) Allowance for laps.
Rates for SC04.19 The rates for movement joints shall generally include for : -
forming
movement (a) Supply of movement joint components including but not be limited to water stops,
joints generally joint filler, bond breaker, back-up materials and sealant, all of which shall be of an
approved proprietary make, as stated in G.S. Item 6.61.
(b) Installation of movement joints strictly as specified in the Contract and in accordance
with the manufacturer's recommendations.
(c) Prior to applying joint sealants, keeping the edges of the joints true and free from
cracks, spalling and other imperfections, and keeping the joints clean, dry and
free from dust or grease.
(d) Fixing joint filler to concrete with a bituminous adhesive prior to casting adjoining
bay.
(e) Pressing and finishing all sealants with a smooth regular surface.
(f) Provision of warranty as specified in the Contract.
04/6
04 CONCRETE WORK 04
SPECIAL CONDITIONS
Rates for SC04.20 The rates for rebound hammer tests shall include for :-
rebound
hammer tests (a) Mobilization, maintenance and demobilization of all necessary mechanical plants
and instruments necessary for the works.
(b) Preparing test areas including removing loose mortar and the like before test.
(c) Providing temporary working platform and protection as required.
(d) Recording and submitting records and test reports.
Quality assurance SC04.21 All structural concrete shall be produced and supplied in accordance with the Quality
for structural Assurance requirement for Structural Concrete as stated in the Contract.
concrete
04/7
04 CONCRETE WORK 04
Item Item
PLAIN CONCRETE Concrete Grade
10P 20P 30P
A B C
Per cubic metre $ $ $
04001 Mass filling, packing, thicknessing and the like......................................................................................................................................... 530.20 569.00 584.00 04001
04002 Foundations................................................................................................................................................................................................. 533.90 572.80 587.70 04002
04003 Beds, paving slabs and the like................................................................................................................................................................... 532.10 570.90 585.80 04003
04004 Blinding under foundations........................................................................................................................................................................ 532.10 570.90 585.80 04004
04005 Curbs, upstands, plinths and the like.......................................................................................................................................................... 582.70 621.50 636.40 04005
REINFORCED CONCRETE Concrete Grade
20MPa 25MPa 30MPa 35MPa 40MPa 45MPa
or 20D or 25D or 30D or 35D or 40D or 45D
A B C D E F
Per cubic metre $ $ $ $ $ $
04006 Foundations, isolated and attached bases and the like ........................................................................ 621.10 638.30 644.20 668.50 698.80 728.50 04006
04007 Ground beams, tie beams and the like.................................................................................................. 625.40 647.80 648.50 672.80 703.10 732.80 04007
04008 Machine bases, thrust blocks and the like............................................................................................ 628.50 645.70 651.60 675.90 706.20 735.90 04008
04009 Ground slabs or suspended slabs.......................................................................................................... 629.70 646.90 652.80 677.10 707.40 737.10 04009
04010 Sloping suspended slabs........................................................................................................................ 632.80 650.00 655.90 680.20 710.50 740.20 04010
04011 Walls...................................................................................................................................................... 638.40 655.60 661.40 685.70 716.00 745.70 04011
04012 Retaining walls...................................................................................................................................... 647.00 664.20 670.10 694.40 724.70 754.30 04012
04013 Piers and columns.................................................................................................................................. 685.80 703.00 708.90 733.20 763.50 793.10 04013
04014 Beams..................................................................................................................................................... 655.60 672.80 678.70 703.00 733.30 763.00 04014
04015 Fins and the like..................................................................................................................................... 659.90 677.10 683.00 707.30 737.60 767.30 04015
04016 Casings to structural steelwork............................................................................................................. 672.90 690.10 695.90 720.20 750.50 780.20 04016
04017 Stairs...................................................................................................................................................... 707.40 724.60 730.40 754.70 785.00 814.70 04017
04018 Curbs, upstands and the like................................................................................................................. 651.30 668.50 674.40 698.70 729.00 758.60 04018
Extra over either of Items 04006 to 04018 inclusive for concrete in water retaining structures.................................................................................................. 10%
Extra over either of Items 04006 to 04018 inclusive for pulverized fuel ash ............................................................................................................................... 2%
Extra over either of Items 04006 to 04018 inclusive for concrete with recycled coarse aggregates............................................................................................ 15%
04/8
04 CONCRETE WORK 04
Item Item
"NO FINES" CONCRETE
A
Per cubic metre $
04019 No-fines concrete filling................................................................................................................................................................................................................. 328.00 04019
LIGHTWEIGHT CONCRETE
A
Per cubic metre $
04020 Cement and vermiculite (1:6) by volume or other approved lightweight concrete filling, thicknessing, insulation slabs and the like....................................... 890.80 04020
STEEL REINFORCEMENT
A
Per kg $
04021 Mild steel reinforcement n.e. 16 mm diameter............................................................................................................................................................................... 8.90 04021
04022 Ditto exceeding 16 mm diameter.................................................................................................................................................................................................... 8.90 04022
04023 High tensile steel reinforcement 10 - 40 mm diameter.................................................................................................................................................................. 8.50 04023
04024 Fabric reinforcement lapped at joints............................................................................................................................................................................................. 9.50 04024
Extra over either of Items 04021 to 04024 inclusive for epoxy coating including handling, cutting and bending, sampling and testing
(as Specification)............................................................................................................................................................................................................................. 50%
(Note : - The above item will only be paid for, if ordered by Maintenance Surveyor in writing.)
04/9
04 CONCRETE WORK 04
Item Item
FORMWORK Sawn Wrot
formwork formwork
A B
Per square metre $ $
04025 Vertical surfaces of foundations, ground beams, tie beams and the like..................................................................................................................... 186.10 - 04025
04026 Ditto but to casing of structural steelwork.................................................................................................................................................................... 202.60 211.20 04026
04027 Ditto but to machine base, thrust blocks and the like................................................................................................................................................... 198.80 207.40 04027
04028 Ditto but to piers, columns, stanchions and the like..................................................................................................................................................... 205.10 213.70 04028
04029 Ditto but to fins and the like......................................................................................................................................................................................... 202.60 211.20 04029
04030 Soffits of suspended slabs............................................................................................................................................................................................. 199.90 208.50 04030
04031 Sloping soffits of suspended slabs................................................................................................................................................................................ 220.20 228.70 04031
04032 Vertical surfaces of walls.............................................................................................................................................................................................. 202.60 211.20 04032
04033 Battered surfaces of walls............................................................................................................................................................................................. 193.60 202.10 04033
04034 Sides and soffits of beams............................................................................................................................................................................................. 201.20 209.80 04034
04035 Casing of steel beams.................................................................................................................................................................................................... 199.90 208.50 04035
04036 Sloping soffits of stairs.................................................................................................................................................................................................. 220.20 228.70 04036
04037 Edges of curbs, upstands, slabs and the like exceeding 300 mm high........................................................................................................................ 148.10 156.70 04037
04038 Forming upper surfaces sloping exceeding 15 degrees from horizontal...................................................................................................................... 116.40 125.00 04038
Per linear metre
04039 Edges, open strings or risers n.e. 100 mm wide........................................................................................................................................................... 23.40 24.60 04039
04040 Ditto, 100 - 200 mm wide............................................................................................................................................................................................. 38.00 39.20 04040
04041 Ditto, 200 - 300 mm wide............................................................................................................................................................................................. 54.90 59.20 04041
Add to either of Items 04025 to 04041 inclusive if formwork ordered by the Maintenance Surveyor in writing to produce
rough board finish (as G.S. Item 6.73)......................................................................................................................................................................... - 50%
Add to either of Items 04025 to 04041 inclusive if formwork ordered by the Maintenance Surveyor in writing to be left
in position...................................................................................................................................................................................................................... 20% -
Add to either of Items 04025 to 04041 inclusive if formwork curved on plan or elevation to a radius on face n.e. 3.00 m..................................... 30% 30%
Ditto but 3.00 - 15.00 m................................................................................................................................................................................................ 15% 15%
04/10
04 CONCRETE WORK 04
Item Item
PRECAST REINFORCED CONCRETE
Precast reinforced concrete Grade 20D or 20MPa placed in position with mortar or cast into concrete : -
A
Per cubic metre $
04042 Cooking shelf, sink, partition, slabs and the like............................................................................................................................................................................ 1,531.00 04042
04043 Lintols, beams, rafters, struts and columns, cills, strings, copings, cornices, kerbs, pier caps, pit covers and the like............................................................... 1,408.50 04043
04044 Planters, refuse bins and the like.................................................................................................................................................................................................... 1,125.50 04044
04045 Fencing components, posts and the like......................................................................................................................................................................................... 1,562.90 04045
04046 Ventilators, grilles, grille panelled walls and the like.................................................................................................................................................................... 1,469.80 04046
Extra over either of Items 04042 to 04046 inclusive for concrete Grade 30D or 30MPa............................................................................................................. 6%
Take out Take out
and and set Fix
clear aside for only
away re-use
A B C
Per cubic metre $ $ $
04047 Precast item laid or placed in position........................................................................................................................................................ 127.60 114.80 191.30 04047
04048 Ditto but cast into concrete (measured separately) .................................................................................................................................... 178.60 160.70 267.90 04048
04049 Ditto built in or bedded in cement mortar ................................................................................................................................................. 159.50 144.10 239.80 04049
SURFACE TREATMENT TO CONCRETE
A
Per square metre $
04050 Treat surfaces with an approved liquid hardener to horizontal surfaces....................................................................................................................................... 23.50 04050
04051 Ditto but to vertical or sloping surfaces.......................................................................................................................................................................................... 24.50 04051
04052 Treat surfaces with carborundum grains to horizontal surfaces.................................................................................................................................................... 12.20 04052
04053 Ditto but vertical or sloping surfaces.............................................................................................................................................................................................. 13.10 04053
04/11
04 CONCRETE WORK 04
Item Item
FINISHINGS AND SUNDRY LABOURS ON NEW CONCRETE
A
Per square metre $
04054 Float surface fair and even with a wood float including any additional cement required ............................................................................................................ 13.40 04054
04055 Trowel surface hard and smooth with a steel trowel including ditto ............................................................................................................................................ 18.30 04055
04056 Score surface with parallel anti-slip grooves approximately 15 mm wide x 15 mm deep at 100 mm centres ............................................................................ 24.50 04056
04057 Punch small anti-slip holes in surface approximately 15 mm deep at 150 mm centres staggered .............................................................................................. 11.00 04057
04058 Heavily tamp surface to form corrugated non-slip finish .............................................................................................................................................................. 9.80 04058
04059 Damp proof course of bitumen sprayed or brushed on surface at the rate of 0.50 litre/m .......................................................................................................... 22.90 04059
Per linear metre
04060 Form channel n.e. 150 mm girth with rounded bottom finished to falls including angles, ends junctions, outlets,
and similar labours and trowelling smooth ................................................................................................................................................................................... 19.60 04060
04061 Ditto 150 - 300 mm girth ............................................................................................................................................................................................................... 40.40 04061
Add to either of Items 04060 to 04061 inclusive if curved on plan to a radius n.e. 3 m to the centre line ................................................................................. 15%
TAKING DOWN CONCRETE FOR ALTERATION WORKS
Note : -
(i) The following Items 04062 to 04063 inclusive shall only apply to alteration works. All demolition works in respect of
a whole or part of a building shall be measured and priced under the Demolition Section of this Schedule. Concrete of
(ii) Diamond coring shall be measured separately if specifically ordered in writing by the Maintenance Surveyor. any grade
Plain Reinforced
concrete concrete
A B
Per cubic metre $ $
04062 Take down or break out and clear away concrete structural elements in any position n.e. 150 mm thick ................................................................ 362.10 436.70 04062
04063 Ditto exceeding 150 mm thick ..................................................................................................................................................................................... 406.80 493.30 04063
04/12
04 CONCRETE WORK 04
Item Item
CUTTING AND SUNDRY LABOURS ON EXISTING CONCRETE Concrete of
any grade
Plain Reinforced
concrete concrete
A B
Per cubic metre $ $
04064 Cut through wall, floor slab or similar, exceeding 0.05 m for new door, window or other opening, or to enlarge
existing opening, including trimming surfaces to receive new plaster or other finish (finishes measured separately)
(net size of required opening measured) ...................................................................................................................................................................... 436.70 511.20 04064
Per square metre
04065 Hack surface or edge to provide key for new concrete ................................................................................................................................................ 9.80 - 04065
04066 Cut parallel anti-slip grooves approximately 15 mm wide x 15 mm deep at 100 mm centres and make good ......................................................... 24.50 - 04066
04067 Cut small anti-slip holes in surface approximately 15 mm deep at 150 mm centres staggered and make good........................................................ 14.70 - 04067
04068 Cut into concrete floor all over n.e. 25 mm deep, trim and level surface to receive screed ....................................................................................... 15.90 - 04068
04069 Ditto but 25 - 50 mm deep............................................................................................................................................................................................ 30.60 40.40 04069
04070 Add to Item 04069 for each 25 mm deep or part thereof in excess of 50 mm............................................................................................................. 15.90 20.80 04070
04071 Cut sinking exceeding 0.10 m but n.e. 25 mm deep into surface, including trimming and making good back face
and edges (net size of required sinking measured) ...................................................................................................................................................... 22.10 - 04071
04072 Ditto but 25 - 50 mm deep............................................................................................................................................................................................ 36.80 49.00 04072
04073 Add to Item 04072 for each 25 mm deep or part thereof in excess of 50 mm............................................................................................................. 15.90 20.80 04073
Per linear metre
04074 Cut chase, groove or rebate n.e. 0.0005 m sectional area and make good, including pinning in and bedding and
pointing edges of slabs, cills, steps, pipes, and similar items ..................................................................................................................................... 15.90 18.40 04074
04075 Ditto 0.0005 - 0.01 m sectional area ........................................................................................................................................................................... 30.60 40.40 04075
04076 Cut channel n.e. 150 mm girth with rounded bottom finished to falls, and make good including rendering with
15 mm cement and sand (1:3) and forming all angles, ends, junctions, outlets and similar labours ......................................................................... 31.80 41.80 04076
04077 Ditto but 150 - 300 mm girth ....................................................................................................................................................................................... 53.90 63.90 04077
Add to either of Items 04074 to 04077 inclusive if curved on plan to a radius n.e. 3.00 m to the centre line .......................................................... 20% 20%
Add to either of Items 04074 to 04077 inclusive if curved on plan to a radius 3.00 - 15.00 m to the centre line .................................................... 10% 10%
04/13
04 CONCRETE WORK 04
Item Item
CUTTING AND SUNDRY LABOURS ON EXISTING CONCRETE (CONT'D) Concrete of
any grade
Plain Reinforced
concrete concrete
A B
Each $ $
04078 Cut sinking n.e. 0.01 m and 25 mm deep into surface including trimming and making good back face and edges
(net size of required sinking measured) ....................................................................................................................................................................... 7.40 9.80 04078
04079 Add to Item 04078 for each additional 25 mm or part of 25 mm in depth ................................................................................................................. 3.70 4.90 04079
04080 Cut sinking as Item 04078 but 0.01 - 0.10 m ............................................................................................................................................................. 15.90 19.60 04080
04081 Add to Item 04080 for each additional 25 mm or part of 25 mm in depth ................................................................................................................. 8.60 11.00 04081
04082 Cut hole through concrete for pipe, air brick, access panel or similar article n.e. 0.0001 m (net size of pipe or article
measured) and grout or render around reveals in cement mortar (1:2) and make good one or both sides ................................................................ 11.70 13.50 04082
04083 Ditto 0.0001 - 0.0002 m .............................................................................................................................................................................................. 16.50 18.40 04083
04084 Ditto 0.0002 - 0.002 m ................................................................................................................................................................................................ 28.80 34.60 04084
04085 Ditto 0.002 - 0.01 m .................................................................................................................................................................................................... 41.40 53.30 04085
04086 Ditto 0.01 - 0.05 m ...................................................................................................................................................................................................... 76.10 95.20 04086
04087 Cut or drill mortice in existing concrete structure for dowel, end of baluster, bracket, fixing cramp, or similar article
n.e. 0.0001 m (net size of article for end measured) and grout in cement and sand (1:2) and make good ............................................................... 11.10 13.50 04087
04088 Ditto 0.0001 - 0.0002 m .............................................................................................................................................................................................. 16.50 18.40 04088
DIAMOND CORING ON EXISTING CONCRETE
A
Per linear centimetre $
04089 Core diameter n.e. 25 mm............................................................................................................................................................................................................... 3.90 04089
04090 Ditto 25 - 50 mm............................................................................................................................................................................................................................. 4.50 04090
04091 Ditto 50 - 75 mm............................................................................................................................................................................................................................. 5.30 04091
04092 Ditto 75 - 100 mm........................................................................................................................................................................................................................... 6.40 04092
04093 Ditto 100 - 125 mm......................................................................................................................................................................................................................... 8.00 04093
04094 Ditto 125 - 150 mm......................................................................................................................................................................................................................... 10.20 04094
04095 Ditto 150 - 175 mm......................................................................................................................................................................................................................... 12.20 04095
04096 Ditto 175 - 200 mm......................................................................................................................................................................................................................... 13.80 04096
04097 Ditto 200 - 225 mm......................................................................................................................................................................................................................... 17.50 04097
04098 Ditto 225 - 250 mm......................................................................................................................................................................................................................... 22.90 04098
04099 Ditto 250 - 275 mm......................................................................................................................................................................................................................... 27.70 04099
04100 Ditto 275 - 300 mm......................................................................................................................................................................................................................... 31.70 04100
(Note : - The above Items 04089 to 04100 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
04/14
04 CONCRETE WORK 04
Item Item
MOVEMENT JOINTS
A
Per linear metre $
04101 Form horizontal or vertical movement joint through full thickness of slab or wall n.e. 75 mm thick including formwork to one edge,
providing approved centre bulb type plastic water stop 150 mm (minimum) wide and casting in one edge, coating concrete edge with
bitumen at the rate of 0.50 litre/m or with approved proprietary primer at rate recommended by the manufacturer when formwork
removed, supporting and casting in the other edge of the water stop to the abutting slab or wall, and forming cut and welded joints
at all junctions of the water stop in accordance with the manufacturer's instructions ................................................................................................................. 141.20 04101
04102 Add to Item 04101 for each additional 75 mm thickness, or part thereof, of slab or wall ........................................................................................................... 12.90 04102
04103 Cover movement joint with approved "T" or "Y" section P.V.C. or rubber cover strip pressed firmly into the joint including forming
groove in concrete or wall plaster and fixing clips at 300 mm centres ......................................................................................................................................... 115.70 04103
04104 Thoroughly rake out existing mastic pointing to movement joint and enlarge groove in plaster, paving, concrete, etc., as
necessary ready for re-pointing (measured separately) ................................................................................................................................................................. 5.90 04104
Filler thickness (mm)
9.50 12.50 19.00 25.00
A B C D
Per linear metre $ $ $ $
04105 Proprietary preformed rigid joint filler placed and supported in position against horizontal or vertical slab
edge, wall end, etc., n.e. 75 mm thick, including splitting into two widths if necessary to accommodate
plastic water stop (measured separately).................................................................................................................................. 5.70 6.10 6.90 7.70 04105
04106 Ditto 75 - 150 mm thick............................................................................................................................................................ 9.30 10.60 12.70 19.80 04106
04107 Ditto 150 - 225 mm thick.......................................................................................................................................................... 13.00 15.20 18.70 22.90 04107
04108 Ditto 225 - 300 mm thick.......................................................................................................................................................... 14.30 19.60 24.60 30.40 04108
04/15
04 CONCRETE WORK 04
Item Item
MOVEMENT JOINTS (CONT'D)
Point horizontal or vertical joint with one of the following joint sealants
as ordered or approved proprietary made including cleaning and
preparing surfaces of joint to receive the sealant : - Joint size (mm)
5 x 15 5 x 25 15 x 15 15 x 25 15 x 50 25 x 25 25 x 50
A B C D E F G
Per linear metre $ $ $ $ $ $ $
04109 General purpose, oil based standard grade mastic joint
sealant of strong adhesion property and high durability,
body of sealant to remain flexible under paintable skin
which forms between 24-48 hours, sealant to give
weathertight seal and for general pointing, bedding and
joint sealant up to 20 mm wide........................................................................................... 9.00 12.80 20.40 31.90 60.40 - - 04109
04110 Cold applied, two part elastomeric polyurethane black
sealant for joint in concrete paved area, self levelling,
resistant to fuel, oil and hydraulic fluid spillage, to
BS5212, tack free and accept traffic after 16-24
hours of application............................................................................................................. 7.60 10.60 16.50 25.50 47.40 39.60 78.00 04110
04111 Thermoplastic bitumen based black putty joint sealant,
hot applied, for joint in water retaining structures
including vertical and inclined joints of width up to
40 mm wide, weather resistant seal, resistant to
bacteriological attack, for permanent immersion in water,
joint surfaces to be primed with compatible primer from
the same manufacturer and allowed to dry......................................................................... 9.80 13.60 21.30 33.30 62.60 52.70 102.10 04111
04112 Hot poured, black rubber bitumen horizontal joint
sealant, for movement and construction joints of width
up to 65 mm (non trafficking) in concrete pavements and
floor slabs including water retaining structures, potable
water tanks, strong adhesion to concrete and asphalt
surfaces, resistant to grit, porous surfaces to be primed
with compatible primer from the same manufacturer and
allowed to dry...................................................................................................................... 7.50 10.00 14.70 21.80 39.60 33.60 63.30 04112
04113 Liquid polysulphide polymer joint sealant,
including backing rod, for sealing joints of 5-50 mm
wide in brickwork, floors, retaining walls, basements,
subways and movement joints, strong adhesion to most
common substrates, to ISO11600:1993, BS4254 and
ASTM C920-87, Type M, Class 25, surfaces to be
primed with compatible primer from the same
manufacturer as required..................................................................................................... 16.00 23.30 37.10 58.90 84.40 94.60 135.30 04113
04/16
04 CONCRETE WORK 04
Item Item
MOVEMENT JOINTS (CONT'D) Diameter (mm)
15 20 25
A B C
Per linear metre $ $ $
04114 Form movement joint with polyethylene foam backing rod....................................................................................................................... 17.20 21.20 24.60 04114
Joint size (mm)
5 x 15 5 x 25 15 x 15 15 x 25 15 x 50 25 x 25 25 x 50
A B C D E F G
Per linear metre $ $ $ $ $ $ $
04115 Point horizontal or vertical joint with approved epoxy mortar
including cleaning and preparing surfaces of joint and priming
surfaces with approved epoxy primer before applying epoxy mortar................................ 9.40 13.70 17.00 22.40 36.30 33.30 55.10 04115
REBOUND HAMMER TEST
A
Per set $
04116 Carry out rebound hammer test on existing concrete surface in accordance with BS EN 12504-2 including
set up equipment, calibrate, carry out test and submit reports....................................................................................................................................................... 262.00 04116
UNDERLAYS
A
Per square metre $
04117 Reinforced waterproof building paper laid on surfaces................................................................................................................................................................. 5.80 04117
04118 Ditto but fixed to edges of slabs or tops of walls with and including mastic ............................................................................................................................... 10.50 04118
04119 0.08 mm Thick polythene sheet laid on surfaces........................................................................................................................................................................... 7.00 04119
04120 Ditto but fixed to edges of slabs or tops of walls with and including mastic ............................................................................................................................... 12.60 04120
SUPPLY ONLY OF MATERIALS
A
Per cubic metre $
04121 40 mm Granite aggregate................................................................................................................................................................................................................ 71.80 04121
04122 20 mm Ditto.................................................................................................................................................................................................................................... 71.80 04122
04123 Granite fines.................................................................................................................................................................................................................................... 91.70 04123
04124 Sand................................................................................................................................................................................................................................................. 95.50 04124
Per 100 kg
04125 Ordinary Portland cement............................................................................................................................................................................................................... 50.50 04125
04126 Coloured cement............................................................................................................................................................................................................................. 99.40 04126
04/17
Section 05
BRICKWORK AND BLOCKWORK
05 BRICKWORK AND BLOCKWORK 05
SECTION 05
BRICKWORK AND BLOCKWORK
SPECIAL CONDITIONS
Measurement of SC05.01 Brickwork and blockwork shall generally be measured net as built. Where exceeding 225 mm
brickwork and or one brick thick, it shall be measured in cubic metres, and where 225 mm or one brick
blockwork thick or less, it shall be measured in square metres. Flues and chimney breasts shall
generally be measured solid. Apertures and voids for ranges, boilers, grates, cookers etc., shall be
deducted. Deductions shall also be made for string courses, cills, lintols, etc., but only to
the extent of a full brick course in height.
No deduction shall be made for : -
(a) Openings not exceeding 0.10 m.
(b) Flues not exceeding 0.25 m in sectional area.
(c) String courses, cills, lintols, etc., less than a full brick course in height.
Apart from face work, no additional rate will be allowed for brickwork or blockwork
curved on plan or built battered.
Measurement of SC05.02 Facing brickwork shall be measured net over the whole exposed surface including additional
facing brickwork girth of top and bottom returns of oversailing and receding courses, top of copings
and the like. Exposed surfaces of all fair axed arches shall not be deducted from the area
of general facings and measured separately as Extra over general brickwork for
arches.
On no account will facing be measured where the work is to be plastered, rendered or
otherwise covered up, or left rough as in trenches, backs, retaining walls and the like.
Measurement of SC05.03 Fair face work shall be measured net as Extra over the general blockwork over the
fair face whole exposed surface including additional girth of top and bottom returns of oversailing
to blockwork and receding courses, top of copings and the like.
On no account will fair face work be measured where the work is to be plastered,
rendered or otherwise covered up, or left rough as in trenches, backs, retaining walls and
the like.
05/1
05 BRICKWORK AND BLOCKWORK 05
SPECIAL CONDITIONS
Measurement for SC05.04 Measurement for cutting, etc., and sundry labours on existing brickwork and blockwork
cutting and shall include the thickness of any plastering, rendering, or other finishes on both sides. In
sundry labours the case of taking down walls 300 mm thick and less, the net thickness of the brickwork
on existing or blockwork shall be stated.
brickwork and
blockwork
Rates for SC05.05 The rates for brickwork, blockwork and facings shall include for : -
brickwork and
blockwork (a) Rough and fair cuttings and bonding at angles, intersections, etc..
(b) Oversailing and receding courses.
(c) Rough relieving and discharging arches.
(d) Wedging and pinning.
(e) Raking out joints to form key.
(f) Raking out and enlarging joints, and cement or lime mortar pointing to flashings
and the like.
(g) Bedding and pointing frames, plates and the like in cement or lime mortar.
(h) Eaves filling.
(i) Plumbing angles.
(j) Forming square or rebated reveals.
(k) Cutting squints, birdsmouths, splays, chamfers and the like.
(l) Leaving or cutting chases, notches, holes, mortices and the like, and grouting in
ends, pipes and the like, and making good.
(m) Cutting and pinning ends and making good.
(n) Mild steel rod reinforcement or bonding rods painted with two coats of bituminous
paint, galvanised mild steel fabric reinforcement and the like.
(o) Special bonding and tying for conduit installation.
(p) Bonding to existing work.
05/2
05 BRICKWORK AND BLOCKWORK 05
SPECIAL CONDITIONS
Rates for SC05.05 (q) Bonding to walls of different construction.
brickwork and (Cont'd)
blockwork (r) Protection to faced and fair faced work until completion of the Works.
(Cont'd)
(s) Sundry items of like nature to any of the above.
(t) Facing brickwork in all types of bond.
Rates for SC05.06 The rates for blockwork shall further include for : -
blockwork
(a) Special quoin blocks, plain reveal blocks, closers and the like.
(b) In the case of hollow blocks, filling cavities solid with cement mortar at ends,
opening reveals, intersections and similar positions if necessary.
Rates for SC05.07 The rates for fire resisting lightweight concrete blocks shall further include for : -
fire resisting
lightweight (a) Submission of test certificates and manufacturer's guarantee.
concrete
blocks
Rates for SC05.08 The rates for cutting and sundry labour on existing brickwork or blockwork shall include
cutting and for : -
sundry labour
on existing (a) Cutting opening, cutting chase or rebate, cutting hole or sinking, cutting or drilling
brickwork or mortice and similar labour through all types of brickwork and/or blockwork.
blockwork
(b) Removal from the Site of all debris and materials arising from the cutting and
labour operations.
(c) Removal of all related plastering, rendering or other finishes on one or both sides
of brickwork or blockwork.
(d) Making good any disturbed surfaces and existing surfaces.
Rates for SC05.09 The rates for cutting chases, sinkings, grooves, rebates, holes and the like shall include for
cutting chases, removing debris and making good any existing finish.
sinkings, etc.
Glass blocks SC05.10 Glass block panelling can be found in Section 14 - Glazing of this Schedule.
05/3
05 BRICKWORK AND BLOCKWORK 05
Item Item
GENERAL BRICKWORK
Note : - The nominal size of standard brick is 225 x 112.5 x 75 mm.
Thus nominal thickness of : - One brick wall is 225 mm thick.
Half brick wall is 112.5 mm thick.
Brick on edge wall is 75 mm thick.
Brickwork built in cement/lime mortar or cement mortar : -
A
Per cubic metre $
05001 Solid brickwork exceeding one brick thick.................................................................................................................................................................................... 911.80 05001
Per square metre
05002 Brick-on-edge wall.......................................................................................................................................................................................................................... 85.50 05002
05003 Ditto built honeycomb..................................................................................................................................................................................................................... 69.00 05003
05004 Half brick wall................................................................................................................................................................................................................................. 92.20 05004
05005 Ditto built honeycomb..................................................................................................................................................................................................................... 76.70 05005
05006 One brick wall................................................................................................................................................................................................................................. 167.90 05006
05007 One brick staining to wall............................................................................................................................................................................................................... 211.50 05007
05008 Ditto with mortar bed joints but open vertical joints..................................................................................................................................................................... 208.90 05008
05009 Half brick lining to stone or concrete wall bonded to same with and including flushing up solid between the brick wall and
stone or concrete with mortar.......................................................................................................................................................................................................... 93.00 05009
05010 One brick lining ditto...................................................................................................................................................................................................................... 169.70 05010
Per linear metre
05011 Brick-on-edge coping, upstand kerb or similar 75 mm wide including angles and ends.............................................................................................................. 39.50 05011
05012 Ditto but 225 mm wide................................................................................................................................................................................................................... 61.20 05012
Per square metre
05013 Form cavity between brick walls, including providing and building in wall ties in accordance with G.S. items 9.11 and 9.36................................................. 13.70 05013
05/4
05 BRICKWORK AND BLOCKWORK 05
Item Item
BRICK PITS Internal girth (m)
n.e. 0.90 - 1.35 -
0.90 1.35 1.80
A B C
Each $ $ $
05014 Small pit for stop-cock, etc., n.e. 300 mm deep internally constructed of 75 mm thick concrete Grade 10P
base extending to outside face of sides and trowelled smooth and half brick sides in cement mortar finished
fair and pointed, or rendered in 15 mm cement and sand (1:3) internally, including all excavation, disposal
and formwork (cover measured separately)................................................................................................................................................ 68.00 91.50 109.90 05014
05015 Ditto 300 - 600 mm deep internally............................................................................................................................................................ 86.50 121.60 149.30 05015
05016 Ditto 600 - 900 mm deep internally............................................................................................................................................................ 168.00 237.70 308.90 05016
05017 Add to either of Items 05014 to 05016 inclusive for 75 mm thick precast concrete Grade 20P cover slab extending
to outside face of sides, reinforced with and including expanded mesh fabric, finished fair and placed in
position including all moulds and additional excavation........................................................................................................................... 19.20 24.40 37.30 05017
FACING BRICKWORK
A
Per square metre $
05018 Extra over brickwork exceeding one brick thick in any type of bonds for facing and pointing with a neat
struck or flush joint as the work proceeds...................................................................................................................................................................................... 101.10 05018
05019 Ditto but battered............................................................................................................................................................................................................................ 96.80 05019
05020 Half brick wall in any type of bonds faced and pointed with a neat struck or flush joint as the work proceeds one side........................................................... 166.60 05020
05021 Ditto both sides............................................................................................................................................................................................................................... 216.40 05021
05022 One brick wall in any type of bonds faced and pointed with a neat struck or flush joint as work proceeds one side.................................................................. 321.70 05022
05023 Ditto both sides............................................................................................................................................................................................................................... 324.30 05023
Add to either of Items 05018 to 05023 inclusive for work built circular on plan to a radius n.e. 1.50 m.................................................................................... 15%
Add to ditto for work built circular on plan to a radius 1.50 - 15.00 m......................................................................................................................................... 10%
05/5
05 BRICKWORK AND BLOCKWORK 05
Item Item
FACING BRICKWORK (CONT'D)
A
Per linear metre $
05024 Brick-on-edge coping, upstand kerb or similar 75 mm wide including angles and ends.............................................................................................................. 47.40 05024
05025 Ditto but 225mm wide.................................................................................................................................................................................................................... 77.00 05025
05026 Extra over brickwork for one brick axed arch in facing (or arch of purpose made bricks) jointing and pointing........................................................................ 92.50 05026
Add to either of Items 05024 to 05026 inclusive for work built circular on plan to a radius n.e. 1.50 m.................................................................................... 15%
Add to ditto for work built circular on plan to radius 1.50 - 15.00 m............................................................................................................................................ 10%
GENERAL FIRE BRICKWORK AND SUNDRY WORK TO FLUES
Brickwork in approved imported firebricks set and jointed in approved fire cement or in a mortar composed
of one part of high-alumina cement to two parts of finely crushed firebrick by volume : -
A
Per cubic metre $
05027 Solid brickwork exceeding one brick thick in lining to flues, boilers, grates, cookers, and similar positions............................................................................. 3,726.00 05027
Per square metre
05028 Brick-on-edge wall.......................................................................................................................................................................................................................... 284.90 05028
05029 Half brick wall................................................................................................................................................................................................................................. 402.70 05029
05030 One brick wall................................................................................................................................................................................................................................. 873.50 05030
Per square metre
05031 Rendering to flues in approved fire cement or in mortar composed of one part of high-alumina cement to two
parts of finely crushed firebrick by volume 25mm thick............................................................................................................................................................... 288.20 05031
05/6
05 BRICKWORK AND BLOCKWORK 05
Item Item
BLOCKWORK
A
Per cubic metre $
05032 Solid concrete block walling exceeding 225 mm thick in cement mortar..................................................................................................................................... 925.30 05032
05033 Hollow concrete block walling ditto............................................................................................................................................................................................... 1,118.40 05033
Thickness of wall (mm)
n.e 75 75 - 150 150 - 225
A B C
Per square metre $ $ $
05034 Solid concrete block walling in cement mortar.......................................................................................................................................... 91.40 104.20 126.40 05034
05035 Hollow concrete block ditto........................................................................................................................................................................ 93.00 122.90 155.70 05035
05036 Solid vermiculite or other approved lightweight aggregate concrete block walling in
cement/lime/sand (1:2:9) by volume........................................................................................................................................................... 87.60 117.40 146.70 05036
A
Per square metre $
05037 Extra over either of Items 05032 to 05036 inclusive for finishing with a fair face and pointing
with a neat flush or struck joint as the work proceeds................................................................................................................................................................... 8.60 05037
Add to Item 05037 for work built circular on plan to a radius n.e. 1.50 m................................................................................................................................... 15%
Add to ditto for work built circular on plan to a radius 1.50 - 15.00 m......................................................................................................................................... 10%
FIRE RESISTING LIGHTWEIGHT CONCRETE BLOCKS
Fire Rated Period (hours)
Fire resisting lightweight concrete blocks in any size and thickness:- 1 2 3 4 6
A B C D E
Per square metre $ $ $ $ $
05038 Fire resisting lightweight concrete block walling bedded and pointed in fireproof mortar.................................. 118.00 121.10 127.60 131.20 168.80 05038
A
Per square metre $
05039 Extra over Item 05038 for sealing one side of wall with moisture sealer...................................................................................................................................... 1.70 05039
(Note : The above Items 05038 and 05039 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
05/7
05 BRICKWORK AND BLOCKWORK 05
Item Item
PERFORATED CONCRETE BLOCKWORK
A
Per square metre $
05040 90 mm Perforated concrete block walling laid in standard pattern in cement mortar pointed with neat flush or
struck joint both sides as the work proceeds.................................................................................................................................................................................. 110.80 05040
05041 90 mm Ditto but built honeycomb.................................................................................................................................................................................................. 73.80 05041
SUNDRIES
A
Per square metre $
05042 Hack off and clear away existing glass bottling bonded in mortar and make good in cement mortar.......................................................................................... 37.80 05042
Per linear metre
(Note : - The following Items 05043 and 05044 inclusive will not be paid for, if working on new works item.)
05043 Fillet in cement/lime mortar or cement mortar n.e. 0.002 m sectional area................................................................................................................................. 7.70 05043
05044 Add to Item 05043 for each additional 0.001 m or part thereof in sectional area........................................................................................................................ 3.90 05044
Each
05045 Glass or cement "tell-tale" executed complete including inscribing in legible figures the date of fixing, and removing
old "tell-tale" where necessary........................................................................................................................................................................................................ 17.10 05045
05046 Add to Item 05045 if cutting is necessary on stone or concrete wall for fixing............................................................................................................................ 8.60 05046
DAMP PROOF COURSE
A
Per square metre $
05047 One course bituminous felt damp proof course laid on, under, or to vertical face of, walls, lapped 150 mm at joints, and including
cement mortar levelling bed on wall or concrete under (measured net)........................................................................................................................................ 104.00 05047
05/8
05 BRICKWORK AND BLOCKWORK 05
Item Item
CUTTING AND SUNDRY LABOURS ON EXISTING BRICKWORK
OR BLOCKWORK IN CEMENT OR CEMENT/LIME MORTAR
(Note : - The following Items 05048 to 05078 inclusive will not be paid for, if working on new works item.)
A
Per cubic metre $
05048 Cut through wall exceeding 0.05 m for new door, window or other opening, or to enlarge existing opening including
any necessary strutting and shoring required, levelling for cills, cutting toothings and providing and bonding in any new
bricks required, and making out jambs and heads ready to receive new plaster or other finish, cutting and pinning in ends
of new cills, lintols, fixing lugs, cramps, bolts, etc., and clearing away all debris (net size of required opening including
allowance for lintol or arch and cill but excluding pockets for fixing lugs, cramps, bolts, etc., measured. New lintol,
arch, plastering, decoration or "Extra for facing" all measured separately)................................................................................................................................... 774.80 05048
Per square metre
05049 Rake out joints 10 mm deep and re-point in cement or cement/lime mortar with a neat struck weathered or flush joint........................................................... 34.40 05049
05050 Level and prepare top of wall for raising........................................................................................................................................................................................ 38.70 05050
05051 Cut sinking exceeding 0.10 m but n.e. 25 mm deep into surface, including trimming and making good back face and
edges (net size of required sinking measured)............................................................................................................................................................................... 56.00 05051
05052 Add to Item 05051 for each additional 25 mm or part of 25 mm in depth.................................................................................................................................... 47.30 05052
05053 Wedge and pin up top of wall to new soffit................................................................................................................................................................................... 137.70 05053
05054 Bed corrugated roof sheeting on top of wall in cement mortar including pointing edges if required.......................................................................................... 86.10 05054
05055 Make good end or face of wall where existing wall which was bonded in has been removed including providing selected bricks
or blocks and jointing in and pointing if required to match existing (any new plaster, etc. measured separately)...................................................................... 111.90 05055
05056 Cut out decayed or broken bricks or blocks of any thickness and replace with new selected bricks or blocks and joint in and
point, if required, to match existing (in areas where more than seven adjacent bricks or one block are replaced)
(any new plaster, etc. measured separately)................................................................................................................................................................................... 198.00 05056
Per linear metre
05057 Bed frame, plate or similar item n.e. 150 mm wide, when fixing in existing opening or position, in cement mortar and
point one or both sides if required.................................................................................................................................................................................................. 12.20 05057
05058 Ditto 150 - 300 mm wide................................................................................................................................................................................................................ 16.60 05058
05059 Rake out defective joint, at least 10 mm deep around door frame or window, or to flashing or similar, and re-point in cement mortar.................................... 4.80 05059
05060 Rake out crack in wall, beam, slab or other position and point in cement mortar (Note : - Repairs of minor cracks
included in preparation for painting, refer to Section 15 of this Schedule)................................................................................................................................... 4.60 05060
05061 Rake out and enlarge joint for turn in of new lead or asphalt flashing or similar, and point in cement mortar including
lead or teak wedging if necessary................................................................................................................................................................................................... 10.90 05061
05062 Add to either of Items 05057 to 05061 inclusive of pointing in mastic or coloured cement mortar in lieu of cement mortar
(per side pointed)............................................................................................................................................................................................................................ 9.30 05062
05063 Point joint of all sizes with silicon mastic to metal/wood frames or sanitary appliance, etc........................................................................................................ 10.00 05063
05064 Cut chase or rebate n.e. 0.0005 m section area (net size of chase or rebate required measured) in brickwork or blockwork
and make good including pinning in and bedding and pointing in cement mortar to edges of slabs, cills, steps, pipes and similar items................................ 13.30 05064
05065 Ditto 0.0005 - 0.010 m sectional area........................................................................................................................................................................................... 19.60 05065
05066 Ditto 0.010 - 0.030 m sectional area.............................................................................................................................................................................................. 26.30 05066
05/9
05 BRICKWORK AND BLOCKWORK 05
Item Item
CUTTING AND SUNDRY LABOURS ON EXISTING BRICKWORK
OR BLOCKWORK IN CEMENT OR CEMENT/LIME MORTAR (CONT'D)
A
Each $
05067 Cut hole or sinking n.e. 0.01 m and 25 mm deep into surface of brickwork or blockwork including trimming and
making good back face and edges. (net size of required sinking measured)................................................................................................................................. 9.50 05067
05068 Add to Item 05067 for each additional 25 mm or part of 25 mm deep......................................................................................................................................... 6.00 05068
05069 Cut sinking as Item 05067 but 0.01 - 0.10 m................................................................................................................................................................................ 18.90 05069
05070 Add to Item 05069 for each additional 25 mm or part 25 mm deep.............................................................................................................................................. 11.20 05070
05071 Cut hole through brickwork or blockwork for pipe, airbrick or similar, n.e. 0.0001 m (net size of pipe or article measured)
and grout in or render round reveals in cement mortar (1:2) and make good one or both sides................................................................................................... 6.00 05071
05072 Ditto 0.0001 - 0.0002 m................................................................................................................................................................................................................. 12.90 05072
05073 Ditto 0.0002 - 0.002 m................................................................................................................................................................................................................... 21.50 05073
05074 Ditto 0.002 - 0.01 m....................................................................................................................................................................................................................... 30.10 05074
05075 Ditto 0.01 - 0.05 m......................................................................................................................................................................................................................... 38.70 05075
05076 Cut out decayed or broken brick or block of any thickness and replace with new selected brick or block and joint in and point
if required to match existing (in area where not more than seven adjacent bricks or one block is replaced) (any new plaster, etc.,
measured separately)....................................................................................................................................................................................................................... 34.40 05076
(Note : - Rates for ragbolts, rawbolts, etc., in Section 10 - Steel and Metal Work of this Schedule include for all mortices and grouting.)
05077 Cut or drill mortice in brickwork or blockwork for dowel, baluster end, bracket end, fixing cramp, bolt or similar
articles n.e. 0.0001 m (net size of article or end measured) and grout in cement and sand (1:2) and make good...................................................................... 6.00 05077
05078 Ditto 0.0001 - 0.0002 m................................................................................................................................................................................................................. 12.90 05078
TAKING DOWN EXISTING BRICKWORK OR BLOCKWORK
A
Per cubic metre $
05079 Take down and clear away wall in any position exceeding 225 mm thick.................................................................................................................................... 204.10 05079
Per square metre
05080 Take down and clear away wall in any position n.e. 75 mm thick................................................................................................................................................ 19.10 05080
05081 Ditto 75 - 150 mm thick.................................................................................................................................................................................................................. 28.70 05081
05082 Ditto 150 - 225 mm thick................................................................................................................................................................................................................ 51.00 05082
05/10
05 BRICKWORK AND BLOCKWORK 05
Item Item
FIXING RANGES, FIRE SURROUNDS, BOILERS AND SIMILAR Take Take
down down Fix
and and set only
clear aside for
away re-use
A B C
Each $ $ $
05083 Free standing range or kitcheners, with single or double ovens, side or high-pressure boilers, and
feed cistern if required................................................................................................................................................................................ 63.80 67.00 75.80 05083
05084 Domestic boiler, copper, rice container or similar..................................................................................................................................... 41.50 43.40 52.10 05084
05085 Range or kitcheners (not free-standing) with single or double ovens, side or high-pressure
boilers, feed cistern if required................................................................................................................................................................... 102.00 107.10 112.70 05085
05086 Damper and frame, soot door, fire door, fireplace fret or similar (when not included with any
of the above fittings)................................................................................................................................................................................... 9.60 10.20 13.30 05086
FIXING SUNDRY METAL WORK ITEMS Take Take
down down Fix
Fix or place in position (fixing material measured separately) : - and and set only
clear aside for
away re-use
A B C
Each $ $ $
05087 Combined gate, covers, fireplace surround, mantel, range, damper and frame, soot
door, fire door, fireplace fret, fire bar and the like except manhole covers and frames n.e. 3 kg
to concrete, brickwork, blockwork or masonry ......................................................................................................................................... 9.60 10.20 21.80 05087
05088 Ditto 3 - 12 kg.............................................................................................................................................................................................. 19.10 20.40 26.50 05088
05089 Ditto 12 - 24 kg........................................................................................................................................................................................... 25.50 26.20 35.00 05089
05090 Add to Item 05089 for each additional 12 kg or part thereof n.e. 100 kg.................................................................................................. 6.40 7.00 9.50 05090
05091 Safe in any weight....................................................................................................................................................................................... 414.60 435.60 535.10 05091
SUPPLY ONLY OF MATERIALS
A
Per 1,000 $
05092 Bricks............................................................................................................................................................................................................................................... 1,251.60 05092
05093 Facing bricks................................................................................................................................................................................................................................... 2,139.30 05093
05094 Firebricks......................................................................................................................................................................................................................................... 3,070.70 05094
Thickness (mm)
75 100 140 190 220
A B C D E
Per 100 $ $ $ $ $
05095 390 x 190 mm Solid concrete blocks...................................................................................................................... 209.50 279.30 - - - 05095
05096 390 x 190 mm Hollow concrete blocks.................................................................................................................. 200.90 267.90 543.70 634.40 906.20 05096
05/11
Section 06
MASONRY
06 MASONRY 06
SECTION 06
MASONRY
SPECIAL CONDITIONS
Drawings for SC06.01 The sketches for rubble walling as referred to in this Schedule are provided in G.S.
rubble walling Section 10 - Masonry and listed in Annex 'A' - Drawing Schedule and Drawings for
Builder's Works of the Schedule and can be viewed on the ArchSD internet website via the
pathway referred therein.
Measurement SC06.02 All unsquared random rubble walling, hearthing or backing to face of walls shall be
generally measured net and grouped together irrespective of thickness.
All squared rubble walling shall be measured net as fixed.
No deduction shall be made for : -
(a) Openings not exceeding 0.10 m.
(b) String courses, cills, lintols and the like not exceeding 100 mm high.
Apart from fair facing, no additional rate will be allowed for random rubble walling built
curved on plan or battered.
Measurement SC06.03 Squared rubble walls as facing to brick, concrete or random rubble hearthing or backing,
of squared shall be measured net thickness. No addition shall be measured for the additional volume
rubble walls of the bond stones projecting into or through the hearthing or backing and no deduction
shall be made from the hearthing or backing for the volume of such bond stones.
Measurement SC06.04 Fair facing shall be measured net as Extra over the random rubble walls over the whole
of extra over exposed surface including additional girth of top and bottom returns of oversailing and
for fair face receding courses, top of copings and the like.
On no account will fair facing be measured where the work is to be plastered, rendered,
or otherwise covered up or left rough as trenches, backs, retaining walls and the like.
Measurement SC06.05 Battered faces shall be measured net over the exposed surface area on line of batter as
of battered face Extra over stone wall. Battered faces shall not be measured on random rubble
hearthing or backing.
06/1
06 MASONRY 06
SPECIAL CONDITIONS
Measurement SC06.06 The measurement of cutting opening through walls shall be the net size
of cutting required including allowance for lintel or arch. New lintel or arch shall be
opening measured separately.
through walls
Measurement SC06.07 Fully dressed stone shall be measured the smallest square or rectangular
of fully dressed shaped block from which it can be worked.
stone
Measurement SC06.08 Measurement for cutting mortices and the like, or taking down existing stone
for cutting, etc., shall include the thickness of any rendering or other surfacing.
or taking down
existing stone
Rates for all SC06.09 The rates for all random and squared rubble walling, facework and fully
random and dressed stone shall generally include for : -
squared
rubble (a) Irregular shaped roughly cut random rubble or roughly squared
walling, rubble walling.
facework and
fully dressed (b) Preparing all existing beds and joints, hoisting, setting, jointing and
stone pointing the work in any position including all joggles, templates, ties,
generally dowels, cramps, other fixing devices and the like.
(c) Oversailing and receding courses.
(d) Rough and fair cutting and bonding at angles, intersections and the
like.
(e) Rough relieving and discharging arches.
(f) Raking out joints for and pointing as the work proceeds.
(g) Bedding and pointing frames, plates and the like.
(h) Plumbing angles.
(i) Forming reveals, returns, rounded, coved, moulded angles and the like.
(j) Leaving or forming chases, notches, holes, grooves, rebates, throats,
chamfers, arrises, splays, sinkings, margins, mortices and the like and
building in ends, pipes and the like (work where cutting on the face
involved shall be measured).
06/2
06 MASONRY 06
SPECIAL CONDITIONS
Rates for all SC06.09 (k) Casing or protecting work with slurry, cleaning off and rubbing down
random and (Cont'd) on completion if required.
squared
rubble (l) Bonding into existing work.
walling,
facework and (m) Marking for identification and delivery in any matching sequence.
fully dressed
stone (n) Temporary protection and subsequent removal.
generally
(Cont'd)
Rates for SC06.10 The rates for extra over random rubble walling for fair face shall further
extra over include for : -
random
rubble walling (a) Selected quality of random granite rubble in evenness, texture,
for fair face stainless and sharpness of arrises.
(b) Cutting in, replacing with approved quality rubbles and removing
inferiority from Site.
Rates for SC06.11 The rates for squared rubble walling shall further include for : -
squared
rubble walling (a) Preparation of joint faces of each stone to a square and true plane
surfaces, free from hollow or rough area.
(b) Building quoins and jambs in selected stones each 175 to 250 mm high
to bond in with the wall courses if required.
(c) Flushing up backing with cement mortar.
(d) Making good affected works to match existing.
(e) Removal from Site all arisings.
Rates for SC06.12 The rates for take down and set aside for re-use shall include for : -
take down and
set aside for (a) Taking down stonework at any locations.
re-use
(b) Providing, maintaining and dismantling all necessary strutting,
shoring and the like, and working platform.
(c) Cleaning stonework free from mortar or other contaminations.
(d) Multi-handling, storage and delivery of stoneworks to designated
locations including that as directed by the Maintenance Surveyor.
06/3
06 MASONRY 06
SPECIAL CONDITIONS
Rates for SC06.13 The rates for fully dressed granite shall further include for : -
fully dressed
granite (a) Dressing and fine punching on all exposed surfaces accurately.
(b) Forming squared back and punching bed and other sides to produce joints not
exceeding 3 mm thick.
(c) Setting, bedding, jointing and pointing with flush, struck or recessed joints in
cement and granite fines (1:3) mortar.
Rates for SC06.14 The rates for cutting opening through walls shall include for : -
cutting
opening (a) Providing, maintaining and dismantling all necessary strutting, shoring and the like.
through walls
(b) Levelling, cutting, cutting toothing, dressing and the like.
(c) Providing and bonding in new stone, making out jambs, heads and facing and
pointing the same to match existing.
(d) Cutting and pinning in ends of new walls, lintels and the like.
(e) Making good affected works to match existing.
(f) Removal from Site all arisings.
Rates for SC06.15 The rates for cutting toothings shall include for : -
cutting
toothings (a) Providing, maintaining and dismantling all necessary strutting, shoring and the like.
(b) Cutting, dressing and the like.
(c) Providing and bonding new stone as required.
(d) Making good affected works to match existing.
(e) Removal from Site all arisings.
Rates for SC06.16 The rates for cutting holes shall include for : -
cutting holes
(a) Mobilization, maintenance and demobilization of coring plant and other
mechanical plant necessary for the works.
(b) Coring through existing stone works including any finishes.
06/4
06 MASONRY 06
SPECIAL CONDITIONS
Rates for SC06.16 (c) Providing temporary water and power supplies and working platform as required.
cutting holes (Cont'd)
(Cont'd) (d) Grouting in pipes or articles and rendering around reveals with cement mortar as
required.
(e) Making good disturbed surfaces to match existing.
(f) Removal from Site all arisings.
06/5
06 MASONRY 06
Item Item
RANDOM RUBBLE WALLING BUILT DRY Take Take
Supply down down Lay
and and and set only
lay clear aside for
away re-use
A B C D
Per cubic metre $ $ $ $
06001 Walling of any thickness........................................................................................................................................................... 801.70 131.20 167.50 339.20 06001
RANDOM RUBBLE WALLING SOLIDLY
BEDDED AND JOINTED IN CEMENT MORTAR
Per cubic metre
06002 Walling of any thickness........................................................................................................................................................... 966.40 144.70 195.20 468.40 06002
06003 Hearthing or backing of any thickness to squared rubble face wall (measured separately).................................................... 966.40 144.70 195.20 468.40 06003
A
Per square metre $
06004 Extra over random rubble walling or hearthing for fair face in the form as sketch "A"................................................................................................................ 11.20 06004
06005 Add to Item 06004 for battered face............................................................................................................................................................................................... 40.90 06005
Add to either of Items 06004 to 06005 inclusive for work built circular on plan to radius n.e. 1.50 m....................................................................................... 20%
Ditto but 1.50 - 15.00 m.................................................................................................................................................................................................................. 10%
UNCOURSED SQUARED RUBBLE WALLING (AS SKETCH "B") Take Take
SOLIDLY BEDDED AND JOINTED IN CEMENT MORTAR Supply down down Lay
and and and set only
lay clear aside for
away re-use
A B C D
Per square metre $ $ $ $
06006 Walling n.e. 75 mm thick.......................................................................................................................................................... 83.30 14.50 22.10 53.90 06006
06007 Ditto but as facing to brick, concrete or random rubble backing (measured separately) including
bonding screed........................................................................................................................................................................... 115.30 14.10 20.40 72.50 06007
06008 Add to either of Items 06006 to 06007 inclusive for each additional 25 mm or part thereof in thickness ............................ 29.00 4.70 7.00 22.30 06008
06009 Extra over walling for battered face.......................................................................................................................................... 33.30 - - 14.00 06009
Add to either of Items 06006 to 06009 inclusive for work built circular on plan to radius n.e. 1.50 m................................. 20% - - 20%
Ditto but 1.50 - 15.00 m............................................................................................................................................................ 10% - - 10%
06/6
06 MASONRY 06
Item Item
SQUARED RUBBLE WALLING BROUGHT UP TO COURSES Take Take
(AS SKETCH "C") SOLIDLY BEDDED AND JOINTED IN CEMENT MORTAR Supply down down Lay
and and and set only
lay clear aside for
away re-use
A B C D
Per square metre $ $ $ $
06010 Walling n.e. 75 mm thick.......................................................................................................................................................... 97.90 15.70 24.60 58.50 06010
06011 Ditto but as facing to brick, concrete or random rubble hearthing or backing (measured separately).................................... 121.90 15.30 23.80 77.20 06011
06012 Add to either of Items 06010 to 06011 inclusive for each additional 25 mm or part thereof in thickness............................. 31.40 5.10 7.80 24.20 06012
06013 Extra over walling for battered face.......................................................................................................................................... 39.20 - - 16.50 06013
Add to either of Items 06010 to 06013 inclusive for work built circular on plan to radius n.e. 1.50 m................................. 20% - - 20%
Ditto but 1.50 - 15.00 m............................................................................................................................................................ 10% - - 10%
SQUARED COURSED RUBBLE WALLING (AS SKETCH "D")
SOLIDLY BEDDED AND JOINTED IN CEMENT MORTAR
Per square metre
06014 Walling n.e. 75 mm thick.......................................................................................................................................................... 104.90 16.90 27.00 55.60 06014
06015 Ditto but as facing to brick, concrete or random rubble hearthing (measured separately)...................................................... 126.80 18.50 29.10 83.40 06015
06016 Add to either of Items 06014 to 06015 inclusive for each additional 25 mm or part thereof in thickness
(up to a maximum of 250 mm)................................................................................................................................................. 34.30 6.40 10.20 20.80 06016
06017 Extra over walling for battered face.......................................................................................................................................... 42.00 - - 17.70 06017
Add to either of Items 06014 to 06017 inclusive for work built circular on plan to radius n.e. 1.50 m................................. 20% - - 20%
Ditto but 1.50 - 15.00 m............................................................................................................................................................ 10% - - 10%
PREPARATION OF SURFACING FINISH TO RUBBLE WALLING Random Un- Squared Regular
rubble coursed rubble coursed
walling squared walling squared
as Sketch rubble brought rubble
"A" walling up to walling
courses
A B C D
Per square metre $ $ $ $
06018 Prepare surface to regular convex "rock faced" finish including allowance for additional thicknessing............................... 79.00 42.30 42.30 42.30 06018
06019 Prepare surface finish as G.S. item 10.18 including allowance for additional thicknessing................................................... 231.20 120.60 120.60 120.60 06019
06/7
06 MASONRY 06
Item Item
FULLY DRESSED GRANITE Take Take
Supply down down Lay
and and and set only
lay clear aside for
away re-use
A B C D
Per square metre $ $ $ $
06020 Ashlar walling or facing n.e. 100 mm thick............................................................................................................................. 122.30 12.80 17.20 41.50 06020
06021 Ditto 100 mm to 300 mm thick................................................................................................................................................. 244.60 24.90 35.10 82.90 06021
Add to either of Items 06020 to 06021 inclusive for work circular on plan to radius n.e. 1.50 m......................................... 20% - - 20%
Ditto but 1.50 - 15.00 m............................................................................................................................................................ 10% - - 10%
CUTTING AND SUNDRY LABOURS ON EXISTING STONE Un- Squared Regular
Random coursed rubble coursed Fully
(Note : - The following Items 06022 to 06033 will not be paid for, if working rubble squared walling squared dressed
on new works item.) walling rubble brought rubble granite
walling up to walling
courses
A B C D E
Per square metre $ $ $ $ $
06022 Rake out joints not less than 15 mm deep and re-point with flush, struck, recessed or keyed
joint as required in cement mortar.......................................................................................................................... 38.50 29.30 29.30 29.30 24.90 06022
06023 Redress face to wall where discoloured or badly stained by fine punching (any re-pointing
required measured separately)................................................................................................................................. - 27.30 27.30 27.30 30.40 06023
06024 Level and prepare top of wall for raising or to receive damp proof course........................................................... 23.80 23.80 23.80 23.80 - 06024
06025 Make good end or face of wall where existing wall which was bonded in has been removed
including providing cutting and building in any new stone required and facing and pointing
to match existing (vertical face in contact with old wall measured)...................................................................... 88.40 119.30 119.30 119.30 185.30 06025
06026 Cut toothings not less than 100 mm deep and at not more than 300 mm centres vertically
in face of existing wall............................................................................................................................................ 45.00 45.40 45.40 45.40 52.70 06026
Per linear metre
06027 Rake out single detached joint not less than 15 mm deep and re-point with flush, struck,
recessed or keyed joint as required in cement mortar............................................................................................. 5.10 5.10 5.10 5.10 5.10 06027
06028 Rake out from wall crack, etc., cut back edges as required and point with flush joint in
cement mortar.......................................................................................................................................................... 7.70 7.70 7.70 7.70 7.70 06028
A
Each $
06029 Cut or drill mortice for dowel, baluster end, bracket end, fixing cramp, bolt or similar article n.e. 0.0001 m
(net size of article or end measured) and grout in cement and sand (1:2) and make good........................................................................................................... 8.00 06029
06030 Ditto 0.0001 - 0.0002 m................................................................................................................................................................................................................. 13.80 06030
06/8
06 MASONRY 06
Item Item
CUTTING AND SUNDRY LABOURS ON EXISTING STONE (CONT'D) Thickness of stone (mm)
n.e. 150 150 - 300 300 - 450 450 - 600
A B C D
Each $ $ $ $
06031 Cut hole for pipe or similar article n.e. 0.004 m...................................................................................................................... 17.20 34.70 51.90 69.40 06031
06032 Ditto 0.004 - 0.008 m............................................................................................................................................................... 22.20 43.30 64.70 87.10 06032
06033 Ditto 0.008 - 0.017 m............................................................................................................................................................... 34.70 69.70 104.70 139.40 06033
CUTTING LETTERS IN NEW OR EXISTING STONE Height of letter or number (mm)
n.e. 75 75 - 150 150 - 225 225 - 300
A B C D
Each $ $ $ $
06034 Cut plain block letter or number in face of stone including picking out with painting........................................................... 33.00 56.40 71.50 80.70 06034
06035 Cut Chinese character ditto....................................................................................................................................................... 40.00 68.90 88.20 98.80 06035
Add to either of Items 06034 to 06035 inclusive for working on existing stonework.................................................................................................................. 10%
06/9
Section 07
ROOFING AND WATERPROOFING
07 ROOFING AND WATERPROOFING 07
SECTION 07
ROOFING AND WATERPROOFING
SPECIAL CONDITIONS
Definition of SC07.01 Whole roof slope shall mean an area extending from one gable wall to another, from gable
whole roof wall to hip or valley between two hips, between two valleys, or between hip and valley in
slope length, and from eaves to ridge in breath and shall include any subsidiary features such as
roofs to dormers which may be contained within such area.
Particular SC07.02 Laying or re-laying of proprietary roofing system or floor waterproofing system apart from
Preamble patch repairs shall be measured in accordance with this Section 07 - Roofing and
Waterproofing. Patch repairs to proprietary roofing system or floor waterproofing system
shall be measured in accordance with Section 16 - Repairs and Alteration to Specialty
Works.
Rates for SC07.03 The rates for roofing and waterproofing shall generally include for : -
roofing and
waterproofing (a) Works at any height and locations.
generally
(b) Works to new or existing surfaces in repairs.
(c) Forming and including movement joints, expansion joints and the like, and
allowing for laps including side and end laps when required.
(d) Allowing for cutting, waste and breakage including those at abutments, top edges,
verges, hips and valleys.
(e) Preparing, cleaning and protection of surfaces to receive roofing or waterproofing
materials.
(f) Fixing or laying to falls and currents.
(g) Sealing at edges, joints and around intersections and projections.
(h) All narrow widths and small areas.
(i) Cleaning and priming to surfaces prior to applying roofing or waterproofing
materials all in accordance with the manufacturer's instructions.
(j) Cutting back existing roofing or waterproofing materials to provide joints for new
roofing or waterproofing when required.
07/1
07 ROOFING AND WATERPROOFING 07
SPECIAL CONDITIONS
Rates for SC07.03 (k) Allowing all cutting, fitting, dressing and making good around rainwater outlets,
roofing and (Cont'd) pipes, flues, openings and the like.
waterproofing
generally (l) Sampling and testing of roofing or waterproofing materials.
(Cont'd)
(m) Providing shop drawings as necessary for the works.
(n) Providing waterproofed rain shelter or any other covers completed with rigid
framing when required throughout the progress of the work to roof areas to
prevent the ingress of rain or other water.
(o) Providing temporary drainage system throughout the progress of the work.
(p) Making good affected areas to match existing.
(q) Temporary protective measures, cleaning and removing all arisings.
(r) Infra-red thermograph testing when required.
(s) Keep a register of all dangerous substances including those hazardous to health,
which are delivered to and stored on Site for use on the Works. The register
include information physical and chemical properties, hazards, safe handling and
storage, precautionary measures to be taken, first aid measures, disposal of
containers and surplus of waste materials, and measures to be taken in case of
accidents.
(t) Leaving roof or floor clean, windproof and watertight on completion and cleaning
out rainwater outlets and gutters.
(u) Provision of manufacturer's guarantee and warranty.
CORRUGATED OR PROFILED SHEET ROOFING
Measurement SC07.04 Corrugated or profiled sheet roofing shall be measured flat over the net area covered (girth
of corrugated or of corrugations not measured) including ridges, hips, valleys, channels, gutters and the like.
profiled sheet In the case of sloping roof, it shall be measured flat over the exposed surfaces (girth of
roofing corrugations not measured). No deduction shall be made for openings not exceeding 0.50 m.
Rates for SC07.05 The rates for corrugated or profiled sheet roofing shall further include for : -
corrugated or
profiled sheet (a) Allowing all notching and fitting edges of sheets and mitring corners as required,
roofing and all mitred angles, junctions and ends on ridges and hips.
(b) Allowing all eaves, jambs, lintel filling pieces, barges boards, corner pieces and
the like.
07/2
07 ROOFING AND WATERPROOFING 07
SPECIAL CONDITIONS
CORRUGATED OR PROFILED SHEET ROOFING
Rates for SC07.05 (c) Spot, fillet or seam welding, brazing or soldering.
corrugated or (Cont'd)
profiled sheet (d) Drilling holes for and providing all drive screws, self-tapping screws, rivets, bolts,
roofing hook bolts, nuts, metal and rubber washers, and plastic caps for fixing to purlins
(Cont'd) or framing spaced at any interval.
(e) Drilling holes to existing or new purlins or framing spaced at any interval for the
fixing of corrugated or profiled sheet roofing as required.
(f) Forming and including holes for pipes or articles.
(g) Recommended fixing method in accordance with the manufacturer's instructions.
(h) Forming movement joints as required.
(i) Forming sheets to required curvature on curved roofs.
(j) In the case of proprietary steel/aluminium sheet roofing, provision of subgrit and
purlin system to the roofing including design and submission of RSE calculations
and shop drawings.
(k) All necessary testing to ensure integrity and water-tightness of the whole roofing
system.
PROPRIETARY GREEN ROOFING SYSTEM
Measurement SC07.06 Supply and installation of proprietary green roofing system shall be measured as the net
of proprietary surface area of the face to be covered. No deduction shall be made for voids not
green roofing exceeding 0.50 m.
system
Rates for SC07.07 The rates for proprietary green roofing system shall further include for :
proprietary
green roofing (a) Preparation and making good existing roof.
system
(b) Condition and structural survey to existing roof including preparation and
submission of records and reports.
(c) Engagement of a Registered Structural Engineer for checking and verifying the
imposed loading of the proprietary green roof system onto the existing structure
including preparation and certification of all required structural submissions.
07/3
07 ROOFING AND WATERPROOFING 07
SPECIAL CONDITIONS
PROPRIETARY GREEN ROOFING SYSTEM
Rates for SC07.07 (d) Including, but not limited to, roof barrier system, moisture retention layer,
proprietary (Cont'd) drainage layer, drainage inspection chamber, filter layer and light weight growing
green roofing medium.
system
(Cont'd) (e) Ground covers of approved species and spacing including necessary fertilizers.
(f) Submission of shop drawings, working drawings and as-built drawings.
(g) Submission of samples with composition report for growing mediums and
groundcovers.
(h) Provision of automatic irrigation system but excluding electrical installation
(measured separately).
(i) Submission of photographical records.
(j) Establishment works after completion for a period of 12 months including
replacement of vegetation upon failure of vegetation for becoming established.
(k) Provision of warranty.
(l) Submission of working programme.
(m) Submission of maintenance and operation manual.
BITUMEN FELT BUILT-UP AND BITUMINOUS EMULSION ROOFING
Measurement SC07.08 Bitumen felt built-up and bituminous emulsion roofing shall be measured net over the whole
of bitumen felt exposed finished top surface, additional girth of vertical or sloping faces and sides or ends
built-up and of upstands, gutters, flashings, skirtings, edge coverings, steps in roof level and the like.
bituminous No deduction shall be made for openings not exceeding 0.50 m.
emulsion
roofing
Rates for SC07.09 The rates for bitumen felt built-up and bituminous emulsion roofing shall further
bitumen felt include for : -
built-up and
bituminous (a) Roofing to flat, sloping or curved roofs.
emulsion
roofing (b) Allowing for all laps, cutting and waste on felts and glass fibre membrane where
applicable.
07/4
07 ROOFING AND WATERPROOFING 07
SPECIAL CONDITIONS
BITUMEN FELT BUILT-UP AND BITUMINOUS EMULSION ROOFING
Rates for SC07.09 (c) Dressing to sides or ends of upstands, gutters, flashings, skirtings, edge coverings,
bitumen felt (Cont'd) steps in roof level and the like, including angles, junctions, turn-in edges, welted
built-up and drips and the like.
bituminous
emulsion (d) Making good surfaces including filling cracks with bitumen or emulsion.
roofing
(Cont'd) (e) Checking the felt roofing works with infra-red thermo-scanning equipment or
other testing equipment on water tightness as the work proceeds.
(f) Replacement of roofing installation if failing in the non-destructive test.
Measurement of SC07.10 Measurement of strip off existing bitumen felt built-up roofing and bituminous emulsion
strip off existing roofing shall not be measured when the backing screed, sheet roofing or insulation layer is
bitumen felt also taking down simultaneously unless it is specifically ordered by the Maintenance
built-up roofing Surveyor in writing.
and bituminous
emulsion roofing
MASTIC ASPHALT (ROCK ASPHALT) ROOFING
Measurement of SC07.11 Measurement of strip off existing mastic asphalt roofing shall not be measured when the
strip off existing backing screed, sheet roofing or insulation layer is also taking down simultaneously unless
mastic asphalt it is specifically ordered by the Maintenance Surveyor in writing.
roofing
PROPRIETARY ROOFING SYSTEM AND FLOOR
WATERPROOFING SYSTEM
Measurement SC07.12 Proprietary roofing system and floor waterproofing system shall be measured net over the
of proprietary whole exposed finished top surface, additional girth of vertical or sloping faces and sides
roofing system or ends of upstands, gutters, flashings, skirtings, edge coverings, steps in roof level and the
and floor like. No deduction shall be made for openings not exceeding 0.50 m.
waterproofing
system Drip flashing, fascia flashing, eave flashing, toothed plate, fascia corner flashing, ridge
flashing, verge flashing, fascia capping, gutters and the like for the proprietary roofing
system shall be measured the net length as fixed.
Proprietary roofing system or floor waterproofing system referred hereinafter shall mean
the waterproof covering materials approved by the Maintenance Surveyor.
For avoidance of doubt, all rates in this sub-section shall deem to apply to works executed
by the specialist contractors or applicators approved by the Maintenance Surveyor.
07/5
07 ROOFING AND WATERPROOFING 07
SPECIAL CONDITIONS
PROPRIETARY ROOFING SYSTEM AND FLOOR
WATERPROOFING SYSTEM
Measurement SC07.13 Measurement of strip off existing proprietary roofing system and floor waterproofing
of strip off system shall not be measured when the backing screed, sheet roofing or insulation layer is
existing also being taken down simultaneously unless it is specifically ordered by the Maintenance
proprietary Surveyor in writing.
roofing system
and floor
waterproofing
system
Rates for SC07.14 The rates for proprietary roofing system and floor waterproofing system shall further
proprietary include for : -
roofing system
and floor (a) Laying on flat, sloping or curved roofs or floors.
waterproofing
system (b) Inspection, preparing, cleaning and drying surfaces including removing all grease,
contaminants, dust, loose stones, debris and the like.
(c) Applying the proprietary roofing system or floor waterproofing system using
spray, trowel or brush application all in accordance with the manufacturer's
instructions.
(d) Dressing to sides or ends of upstands, gutters, flashings, skirtings, edge coverings,
steps in roof, floor and the like, including angles, junctions, turn-in edges, welted
drips and the like all in accordance with the manufacturer's instructions.
(e) Forming fillets with cement mortar at junction between slabs and walls.
(f) Making good surfaces of substrate including filling cracks with bitumen emulsion
or any other materials recommended by the manufacturer's recommendations.
(g) Replacement of roofing or floor waterproofing installation if failing in the
non-destructive test.
(h) Providing protective boarding in accordance with the manufacturer's instructions,
if required.
(i) Submission of catalogues, technical literature and other documentation covering
the materials supplied.
(j) Providing all reports and maintenance manuals.
(k) Providing deeds of warranty in compliance with the Contract requirements.
07/6
07 ROOFING AND WATERPROOFING 07
SPECIAL CONDITIONS
ROOF TILING AND INSULATION BOARD
Measurement SC07.15 Roof tiling and insulation board shall generally be measured as the net area covered when
of roof tiling fixed or laid. No deduction shall be made for voids not exceeding 0.50 m.
and insulation
board
generally
Rates for roof SC07.16 The rates for roof tiling and insulation board shall generally include for : -
tiling and
insulation (a) Working at any height and locations.
board
generally (b) Working to new or existing surfaces in repairs.
(c) All straight or raking cutting and waste.
(d) Narrow widths and small quantities.
(e) Forming and including all joints between new and existing materials.
(f) Laying level or to slopes and finishing to falls and currents.
(g) Mitred edges to external corners and the like.
(h) Covering up and protecting where necessary.
Rates for SC07.17 The rates for roofing tiles including "Canton" tiles, concrete tiles, insulating tiles and foam
roofing tiles board tiles shall further include for forming expansion joints and fill with cold bitumen or all
other approved sealants to roofing tiles as provided in G.S. Items 6.61, 6.62 and 18.120.
Screeds to roofing SC07.18 Screeds to roofing, flooring or tiling can be found in Section 11 - Plastering and Finishes of
or tiling this Schedule.
NON-DESTRUCTIVE TEST
Rates for SC07.19 The rates for non-destructive test shall include for : -
non-destructive
test (a) Constructing temporary dams to compartmentalize large roofs as required and
subsequent removal.
(b) Temporary blocking to all outlets flooding the roof, releasing water and
subsequent removal of blockages.
07/7
07 ROOFING AND WATERPROOFING 07
SPECIAL CONDITIONS
NON-DESTRUCTIVE TEST
Rates for SC07.19 (c) Carrying out test of infra-red scanning by an approved independent specialist in
non-destructive (Cont'd) accordance with the Specification as adopted in the Contract including providing
test all necessary labour, supervisory staff and equipment.
(Cont'd)
(d) In the case of new roofing system, re-testing up to the satisfaction of the
Maintenance Surveyor.
(e) Submission of reports.
SPECIFICATION FOR ROOFING
G.S. clauses SC07.20 G.S. clauses for "Canton" tiles and concrete roof tiles can be found in the Finishes Section
of the General Specification for Building.
07/8
07 ROOFING AND WATERPROOFING 07
Item Item
PROFILED UNREINFORCED RIGID PVC SHEET ROOFING Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
07001 0.80 mm Profiled unreinforced rigid PVC roofing sheet in any profile, colour and transparency
fixed to timber framing (measured separately)......................................................................................................................... 76.20 3.80 5.70 24.40 07001
07002 Ditto but fixed to curved timber framing.................................................................................................................................. 76.40 4.20 6.30 26.30 07002
07003 0.80 mm Profiled unreinforced rigid pvc roofing sheet in any profile, colour and transparency
fixed to steel framing (measured separately)............................................................................................................................ 77.60 4.00 6.00 25.60 07003
07004 Ditto but fixed to curved steel framing..................................................................................................................................... 77.90 4.20 6.30 26.80 07004
A
Each $
07005 Cut hole through existing sheet roofing for pipes or articles in any size and thickness................................................................................................................ 6.80 07005
PROFILED GLASS-FIBRE REINFORCED PLASTIC (GRP) SHEET ROOFING Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
07006 6 mm Profiled glass-fibre reinforced plastic (GRP) sheet roofing in any profile, colour and
transparency fixed to timber framing (measured separately)................................................................................................... 143.90 8.30 12.80 51.60 07006
07007 Ditto but 8 mm thick................................................................................................................................................................. 185.30 8.70 13.40 54.20 07007
07008 Ditto but 10 mm thick............................................................................................................................................................... 226.70 9.10 14.00 56.80 07008
07009 Ditto but 12 mm thick............................................................................................................................................................... 268.10 9.50 14.70 59.40 07009
07010 6 mm Profiled glass-fibre reinforced plastic (GRP) sheet roofing in any profile, colour and
transparency fixed to curved timber framing (measured separately)....................................................................................... 144.90 9.10 14.00 56.80 07010
07011 Ditto but 8 mm thick................................................................................................................................................................. 186.70 9.60 14.70 59.70 07011
07012 Ditto but 10 mm thick............................................................................................................................................................... 228.50 10.00 15.40 62.50 07012
07013 Ditto but 12 mm thick............................................................................................................................................................... 270.30 10.50 16.10 65.30 07013
07/9
07 ROOFING AND WATERPROOFING 07
Item Item
PROFILED GLASS-FIBRE REINFORCED PLASTIC (GRP) SHEET ROOFING Take Take
(CONT'D) Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
07014 6 mm Profiled glass-fibre reinforced plastic (GRP) sheet roofing in any profile, colour and
transparency fixed to steel framing (measured separately)...................................................................................................... 148.90 8.70 13.40 54.20 07014
07015 Ditto but 8 mm thick................................................................................................................................................................. 192.50 9.10 14.10 56.90 07015
07016 Ditto but 10 mm thick............................................................................................................................................................... 236.10 9.60 14.70 59.70 07016
07017 Ditto but 12 mm thick............................................................................................................................................................... 279.60 10.00 15.40 62.40 07017
07018 6 mm Profiled glass-fibre reinforced plastic (GRP) sheet roofing in any profile, colour and
transparency fixed to curved steel framing (measured separately).......................................................................................... 149.90 9.60 14.70 59.70 07018
07019 Ditto but 8 mm thick................................................................................................................................................................. 194.00 10.10 15.50 62.60 07019
07020 Ditto but 10 mm thick............................................................................................................................................................... 237.90 10.50 16.20 65.60 07020
07021 Ditto but 12 mm thick............................................................................................................................................................... 282.00 11.00 17.00 68.60 07021
A
Each $
07022 Cut hole through existing sheet roofing for pipes or articles in any size and thickness................................................................................................................ 15.60 07022
07/10
07 ROOFING AND WATERPROOFING 07
Item Item
GALVANISED STEEL SHEET ROOFING Take Take
Supply down down Fix
Steel sheet roofing as G.S. Item 12.72 : - and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
07023 Corrugated steel sheet roofing n.e. 0.60 mm thick in any corrugation fixed to timber framing (measured
separately).................................................................................................................................................................................. 71.30 4.50 5.70 19.40 07023
07024 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 75.70 4.60 5.90 20.00 07024
07025 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 88.10 4.90 6.30 21.20 07025
07026 Corrugated steel sheet roofing n.e. 0.60 mm thick in any corrugation fixed to curved timber framing
(measured separately)................................................................................................................................................................ 85.90 4.90 6.30 21.40 07026
07027 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 93.90 5.10 6.50 22.00 07027
07028 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 113.50 5.40 6.90 23.30 07028
07029 Corrugated steel sheet roofing n.e. 0.60 mm thick in any corrugation fixed to steel framing
(measured separately)................................................................................................................................................................ 81.50 4.60 5.90 20.00 07029
07030 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 89.50 4.70 6.10 20.60 07030
07031 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 107.00 5.00 6.40 21.80 07031
07032 Corrugated steel sheet roofing n.e. 0.60 mm thick in any corrugation fixed to curved steel framing
(measured separately)................................................................................................................................................................ 87.30 5.10 6.50 22.00 07032
07033 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 96.30 5.20 6.70 22.70 07033
07034 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 118.00 5.50 7.10 24.00 07034
A
Each $
07035 Cut hole through existing sheet roofing for pipes or articles in any size and thickness................................................................................................................ 13.50 07035
07/11
07 ROOFING AND WATERPROOFING 07
Item Item
PROPRIETARY PROFILED STEEL SHEET ROOFING
Proprietary steel profiled sheet cladding in concave or convex shapes, maximum length of sheet
that can be curved is 12 m, to Australian Standard AS1397-1993 and Malaysian Standard MS1196, Take Take
0.42 mm BMT with minimum yield strength of 550 MPA, sheets coating shall comprise alloy of Supply down down Fix
zinc, aluminium and silicon applied by hot dip process, thickness 0.05 mm thick to AS1397 for and and and set only
coating class AZ150, paint coating to AS2728 : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
07036 0.47 mm Thick steel profiled sheeting fixed to timber framing............................................................................................... 375.50 4.50 5.70 50.70 07036
07037 Ditto but fixed to curved timber framing.................................................................................................................................. 431.70 4.90 6.30 55.70 07037
07038 0.47 mm Thick steel profiled sheeting fixed to steel framing.................................................................................................. 375.70 4.60 5.90 52.20 07038
07039 Ditto but fixed to curved steel framing..................................................................................................................................... 434.70 5.10 6.50 57.40 07039
Proprietary steel profiled sheet cladding with concealed fastening, available in two thickness
(0.48 mm & 0.6 mm BMT) with minimum yield strength of 550 MPA, metallic hot dip coated with
alloy of zinc, aluminium and silicon, coating mass to be 150 g/m2 coated both sides, to Australian
Standard AS1397-1993 and Malaysian Standard MS1196, wind pressure capacities to
AS1562.1-1992 and AS4040.2-1992 : -
Per square metre
07040 0.53 mm Thick steel profiled sheeting fixed to timber framing............................................................................................... 419.40 4.60 5.90 52.20 07040
07041 Ditto but 0.65 mm thick............................................................................................................................................................ 464.00 4.70 6.00 53.20 07041
07042 0.53 mm Thick steel profiled sheeting fixed to curved timber framing................................................................................... 422.00 4.90 6.30 55.70 07042
07043 Ditto but 0.65 mm thick............................................................................................................................................................ 468.00 5.20 6.60 58.50 07043
07044 0.53 mm Thick steel profiled sheeting fixed to steel framing.................................................................................................. 419.40 4.60 5.90 52.20 07044
07045 Ditto but 0.65 mm thick............................................................................................................................................................ 464.00 4.80 6.20 54.80 07045
07046 0.53 mm Thick steel profiled sheeting fixed to curved steel framing...................................................................................... 423.20 5.10 6.50 57.40 07046
07047 Ditto but 0.65 mm thick............................................................................................................................................................ 469.20 5.30 6.80 60.30 07047
07/12
07 ROOFING AND WATERPROOFING 07
Item Item
PROPRIETARY GALVANISED STEEL FLASHING, CAPPING, ETC. Take Take
Supply down down Fix
Proprietary steel profiled sheeting with XRW colourbond finish matching with proprietary steel and and and set only
sheet roofing fixing in fasteners or screws in accordance with the manufacturer's recommendations : - fix clear aside for
away re-use
A B C D
Per linear metre $ $ $ $
07048 0.60 mm Thick steel flashing or capping n.e. 200 mm girth.................................................................................................... 102.90 1.30 1.30 26.50 07048
07049 Ditto 200 - 400 mm girth.......................................................................................................................................................... 154.00 2.60 3.20 39.80 07049
07050 Ditto 400 - 600 mm girth.......................................................................................................................................................... 189.40 3.80 7.00 45.40 07050
07051 Ditto 600 - 800 mm girth.......................................................................................................................................................... 236.70 6.40 8.90 49.90 07051
07052 Ditto 800 - 1000 mm girth........................................................................................................................................................ 270.60 7.70 10.90 53.10 07052
Add to either of Items 07048 to 07052 inclusive for curved works......................................................................................... 10% - - 10%
GALVANISED STEEL SHEET RIDGING, GUTTERS, ETC. Take Take
Supply down down Fix
1 mm Thick galvanized mild steel sheet (painting measured separately) : - and and and set only
fix clear aside for
away re-use
A B C D
Per linear metre $ $ $ $
07053 Ridge or hip plain capping of approximately 450 mm girth with 75 mm roll, lapped 150 mm at end joints
(measured net)........................................................................................................................................................................... 64.00 4.50 6.40 16.90 07053
07054 Ditto but both edges corrugated, cut and scribed as necessary to suit sheet roofing (measured net)...................................... 72.00 5.70 8.30 21.10 07054
07055 Half-octagonal shaped valley gutter of approximately 300 x 175 mm deep, lapped 150 mm at end joints
(measured net)........................................................................................................................................................................... 107.70 5.70 8.30 19.40 07055
07/13
07 ROOFING AND WATERPROOFING 07
Item Item
ALUMINIUM SHEET ROOFING Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
07056 Corrugated aluminium sheet roofing n.e. 0.60 mm thick in any corrugation and colour
fixed to timber framing (measured separately) ........................................................................................................................ 298.30 3.80 5.10 15.20 07056
07057 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 356.60 3.90 5.30 15.70 07057
07058 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 443.90 4.20 5.60 16.60 07058
07059 Corrugated aluminium sheet roofing n.e. 0.60 mm thick in any corrugation and colour
fixed to curved timber framing (measured separately)............................................................................................................. 305.60 4.20 5.60 16.70 07059
07060 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 371.10 4.30 5.80 17.20 07060
07061 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 451.10 4.60 6.10 18.20 07061
07062 Corrugated aluminium sheet roofing n.e. 0.60 mm thick in any corrugation and colour
fixed to steel framing (measured separately)............................................................................................................................ 299.10 3.90 5.30 15.70 07062
07063 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 358.00 4.10 5.40 16.10 07063
07064 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 445.30 4.30 5.70 17.10 07064
07065 Corrugated aluminium sheet roofing n.e. 0.60 mm thick in any corrugation and colour
fixed to curved steel framing (measured separately)................................................................................................................ 306.30 4.30 5.80 17.20 07065
07066 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 372.60 4.50 6.50 17.70 07066
07067 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 451.90 4.70 6.80 18.80 07067
A
Each $
07068 Cut hole through existing sheet roofing for pipes or articles in any size and thickness................................................................................................................ 13.50 07068
07/14
07 ROOFING AND WATERPROOFING 07
Item Item
ALUMINIUM FLASHING, CAPPING, ETC. Take Take
Supply down down Fix
0.60 mm Thick aluminium colorbond finish matching with aluminium sheet roofing fixing in and and and set only
fasteners or screws : - fix clear aside for
away re-use
A B C D
Per linear metre $ $ $ $
07069 0.60 mm Thick steel flashing or capping n.e. 200 mm girth.................................................................................................... 69.90 1.30 1.90 4.20 07069
07070 Ditto 200 - 400 mm girth.......................................................................................................................................................... 105.50 3.20 4.50 12.70 07070
07071 Ditto 400 - 600 mm girth.......................................................................................................................................................... 157.20 5.10 10.20 19.40 07071
07072 Ditto 600 - 800 mm girth.......................................................................................................................................................... 212.20 9.60 12.80 27.00 07072
07073 Ditto 800 - 1000 mm girth........................................................................................................................................................ 265.20 10.20 14.70 33.80 07073
Add to either of Items 07069 to 07073 inclusive for curved works......................................................................................... 10% - - 10%
ALUMINIUM SHEET RIDGING, GUTTERS, ETC.
1.00 mm Thick aluminium colorbond finish fixing in fasteners or screws : -
Per linear metre
07074 Ridge or hip plain capping of approximately 450 mm girth with 75 mm roll, lapped 150 mm at end
joints (measured net)................................................................................................................................................................. 131.00 4.50 6.40 16.90 07074
07075 Ditto but both edges corrugated, cut and scribed as necessary to suit sheet roofing
(measured net)........................................................................................................................................................................... 152.80 5.70 8.30 21.10 07075
07076 Half-octagonal shaped valley gutter of approximately 300 x 175 mm deep, lapped 150 mm at end
joints (measured net)................................................................................................................................................................. 180.50 6.40 7.70 22.80 07076
07/15
07 ROOFING AND WATERPROOFING 07
Item Item
PROPRIETARY STEEL/ALUMINIUM SHEET ROOFING
Proprietary sheet roofing system comprising 0.75 mm thick trapezoidal profiled steel shell with Take Take
specialist coating 25 microns thick on visible sides and protective layer (RSL) 10 microns thick on Supply down down Fix
the reverse side to DIN 18807 in any colour including subgrit, purlins and fixing with approved and and and set only
stainless steel fasteners to level or sloping framing all in accordance with the manufacturers fix clear aside for
recommendations : - away re-use
A B C D
Per square metre $ $ $ $
07077 Roofing system.......................................................................................................................................................................... 407.50 5.10 7.00 22.80 07077
Proprietary sandwich roofing system, comprising 0.75 mm thick trapezoidal profiled steel outer
shell and 0.55 mm thick slightly profiled inner shell with specialist coating 25 microns thick on
visible sides and protective layer (RSL) 10 microns thick on the reverse side to DIN 18807 in any
colour enclosing a continuous core of polyurethane rigid foam (HCFC free), thermal resistance
to 1.74 mK/W heat transfer coefficient 0.52 W/m2K to EN ISO6946, including subgrit, purlins and
concealed fixing with integral roof clamps in the longitudinal joint and approved stainless steel
fasteners to level or sloping framing all in accordance with the manufacturers recommendations : -
Per square metre
07078 Roofing system.......................................................................................................................................................................... 3,373.00 19.10 21.10 70.10 07078
0.75 mm Thick proprietary steel sheeting with proprietary coating (25 microns thick) on visible
sides and proprietary protective layer on the reverse side (10 microns thick) in matching colour to
the sandwich roofing system, including forming into any component shape and required girth
including subgrit, purlins and fixing with all necessary clamps and approved stainless steel
fasteners all in accordance with the manufacturer's recommendations : -
Per linear metre
07079 Drip flashing.............................................................................................................................................................................. 298.30 5.70 7.70 25.30 07079
07080 Fascia flashing........................................................................................................................................................................... 400.20 6.40 8.30 27.00 07080
07081 Eave flashing............................................................................................................................................................................. 262.00 5.10 6.40 22.80 07081
07082 Toothed plate complete with foam filler at ridge..................................................................................................................... 276.50 6.40 8.30 27.00 07082
07083 Fascia corner flashing, ridge flashing, verge flashing and the like.......................................................................................... 334.00 6.40 8.30 27.00 07083
07084 Fascia capping, ridge capping and the like.............................................................................................................................. 254.70 6.40 8.30 27.00 07084
Proprietary profiled sheet roofing system of galvanized and plastic coated steel sheet, processed
in roll to form trapezoidal profiles, comprising 0.75 mm thick steel (S280/S320 GD to EN 10326)
with zinc galvanizing (Z275), with 25 microns polyester coating on the exterior surface and 10
microns reverse side coating (RSL) on the interior surface including subgrit, purlins and fixing
with stainless steel self-tapping screws with stainless steel washer (with vulcanized EDPM layer)
to level or sloping framing all in accordance with the manufacturers recommendations : -
Per square metre
07085 Roofing system.......................................................................................................................................................................... 422.00 5.10 7.00 22.80 07085
07/16
07 ROOFING AND WATERPROOFING 07
Item Item
PROPRIETARY STEEL/ALUMINIUM SHEET ROOFING (CONT'D)
0.75 mm Thick proprietary steel (S350 GD to EN 10326) flashing with zinc galvanizing (55% AlZn
AZ 185 to EN 10326), with 25 microns polyester coating on the exterior surface with matching Take Take
colour to cladding profile and 10 microns reverse side coating (RSL) on the interior surface Supply down down Fix
including press-forming to the shape and girth including subgrit, purlins and fixing with all and and and set only
necessary stainless steel self-tapping screws all in accordance with the manufacturer's fix clear aside for
recommendations : - away re-use
A B C D
Per linear metre $ $ $ $
07086 Drip flashing.............................................................................................................................................................................. 232.90 5.70 7.70 25.30 07086
07087 Fascia flashing........................................................................................................................................................................... 349.30 6.40 8.30 27.00 07087
07088 Eave flashing............................................................................................................................................................................. 262.00 5.10 7.00 22.80 07088
07089 Toothed plate complete with foam filler at ridge..................................................................................................................... 276.50 6.40 8.30 27.00 07089
07090 Fascia corner flashing, ridge flashing, verge flashing and the like.......................................................................................... 299.80 6.40 8.30 27.00 07090
07091 Fascia capping, ridge capping and the like.............................................................................................................................. 229.90 6.40 8.30 27.00 07091
Proprietary sandwich roofing panel (concealed fixing type) comprising 0.75 mm thick coil-galvanized
(S350 GD+Z275 to EN 10326) trapezoidal profile steel outer shell with 25 microns PVF2 coating,
continuous core of rigid CFC- and HCFC-free polyurethane foam, 0.55 mm thick coil-galvanized
slightly profiled steel inner shell with 10 microns polyester coating (RSL), proprietary factory-applied
EDPM sealing profile along longitudinal joint including subgrit, purlins and fixing with all necessary
stainless steel self-tapping screws with spherical cap, proprietary roll-formed steel concealed fixing
capping with matching colour on every pitch of sandwich panel all in accordance with the
manufacturers recommendations : -
Per square metre
07092 Roofing panels........................................................................................................................................................................... 3,266.00 17.20 20.40 67.60 07092
0.75 mm Thick proprietary coil-galvanized (S350 GD+Z275 to EN 10326) steel flashing with 25
microns PVF2 coating on weather side with matching colour to sandwich roof panel and 10
microns protective coating (RSL) on the other side, including press-forming to the shape and
girth including subgrit, purlins and all necessary stainless steel self-tapping screws all in
accordance with the manufacturer's recommendations : -
Per linear metre
07093 Drip flashing.............................................................................................................................................................................. 298.30 5.70 7.70 38.80 07093
07094 Fascia flashing........................................................................................................................................................................... 400.20 6.40 8.30 27.00 07094
07095 Eave flashing............................................................................................................................................................................. 262.00 5.10 7.00 22.80 07095
07096 Toothed plate complete with foam filler at ridge..................................................................................................................... 276.50 6.40 8.30 27.00 07096
07097 Fascia corner flashing, ridge flashing, verge flashing and the like.......................................................................................... 334.00 6.40 8.30 27.00 07097
07098 Fascia capping, ridge capping and the like.............................................................................................................................. 254.70 6.40 8.30 27.00 07098
07/17
07 ROOFING AND WATERPROOFING 07
Item Item
PROPRIETARY STEEL/ALUMINIUM SHEET ROOFING (CONT'D)
Proprietary aluminium roofing system comprising 1.00 mm thick in 65/400 profile with PVDF 2
coats finish (23-25microns) on weather side for outer liner in one single sheet for the whole roof
run (no end laps allowed) and 0.80 mm thick Kaibau TR 35/200 of the same material as the outer
liner with polyester coating on underside as the inner liner infilled evenly with 100 mm thick
mineral wool with fire performance complying BS476 Part compressed to 85 mm at a density of
40 kg/m3 with vapour barrier including subgirt, purlins and fixing with necessary ST-Clips and
approved self-tapping screws all in accordance with manufacturer's recommendations, on site Take Take
fabricated system to achieve a maximum thermal insulation U-value of 0.4W/m2K and minimum Supply down down Fix
Weighted Sound Reduction Index of 31dB with test report showing the compliance to BS 5821 and and and set only
Part 3:1984 and minimum 10 years of material warranty is to be provided on completion : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
07099 Proprietary series insulated roofing system ............................................................................................................................. 2,488.60 20.40 25.50 84.50 07099
Per linear metre
07100 Flashing to fascia....................................................................................................................................................................... 262.00 7.00 8.30 27.00 07100
07101 Flashing to drip.......................................................................................................................................................................... 342.00 5.70 7.70 24.50 07101
07102 Flashing to eave......................................................................................................................................................................... 266.30 5.10 7.00 22.80 07102
07103 Flashing to corner flashing, ridge flashing and verge flashing, etc.......................................................................................... 378.40 6.40 8.30 27.00 07103
07104 Flashing to capping, ridge capping and the like....................................................................................................................... 283.80 6.40 8.30 27.00 07104
07105 Toothed plate complete with foam filler n.e. 1.00 m high....................................................................................................... 269.20 7.00 8.30 27.00 07105
07106 Gutter in any size....................................................................................................................................................................... 225.60 7.00 5.70 7.60 07106
PROPRIETARY GREEN ROOFING SYSTEM
Proprietary green roofing system comprising root barrier, moisture retention layer, drainage layer, drainage inspection chamber,
filter layer, light weight growing medium, groundcovers of approved species and spacing, and including provision of automatic
irrigation system but excluding electrical installation (measured separately), submission of drawings, samples, photographical records,
programme, maintenance and operation manual, provisions of 12-month establishment period, warranty as specified in Specification
as adopted in the Contract and approved Registered Structural Engineer checking on calculation of loadings, all in accordance
with the manufacturer's recommendation : -
A
Per square metre $
07107 Proprietary green roofing system ................................................................................................................................................................................................... 1,673.60 07107
07/18
07 ROOFING AND WATERPROOFING 07
Item Item
BITUMEN FELT BUILT-UP ROOFING Nominal weight
1.8 kg/m2 2.5 kg/m2
A B
Per square metre $ $
07108 Underlayer of bitumen felt fixed to timber roof including nails.................................................................................................................................. 34.60 48.00 07108
07109 Ditto but laid on screed or concrete roof including primer and bonding..................................................................................................................... 43.20 60.10 07109
07110 Subsequent underlayer of bitumen bonded to underlayer including bonding compound........................................................................................... 43.20 60.10 07110
07111 Top layer bonded to underlayers with bonding compound.......................................................................................................................................... - 60.10 07111
A
Per square metre $
07112 Surface dressing with stone chippings on and including base coat of bitumen compound.......................................................................................................... 86.40 07112
REPAIRS TO EXISTING; BITUMEN FELT BUILT UP ROOFING
A
Per square metre $
07113 Strip off existing bitumen felt built-up roofing (any number of layers) fixed on timber battens.................................................................................................. 8.70 07113
07114 Ditto but laid on screed or concrete surfaces.................................................................................................................................................................................. 12.10 07114
BITUMINOUS EMULSION ROOFING Concrete, Corrugated Profiled Bitumen
Concrete Canton steel particle felt built-
tiled roof sheet up roof
roof vertical roof surface roof surface
surface surface surface surface
A B C D E F
Per square metre $ $ $ $ $ $
07115 Apply wash coat, priming coat, two coats of approved bitumen emulsion.......................................... 38.90 46.70 54.40 - 54.40 - 07115
07116 Ditto but with three coats of approved bitumen emulsion................................................................... 50.60 58.30 66.10 - 66.10 - 07116
07117 Apply wash coat, priming coat, one coat of approved bitumen emulsion, one layer
of glass fibre membrane and two coats of approved bitumen emulsion as
G.S. Item 12.32...................................................................................................................................... 70.00 77.80 93.30 - 93.30 - 07117
07118 Ditto but with three coats of approved bitumen emulsion to last as G.S. Item 12.32......................... 77.80 93.30 101.00 - 101.00 - 07118
07119 Apply wash coat and primer to grooves, filling grooves with approved bitumen emulsion
and sand (1:3) by volume, apply one coat of approved cover coating and two coats of
approved bitumen emulsion including cutting out cracks exceeding 5 mm wide
as G.S. Item 12.33 ................................................................................................................................ - - - - - 70.00 07119
07120 Apply one coat of approved cover coating, one coat of approved bitumen emulsion,
one layer of glass fibre membrane and two coats of approved bitumen emulsion
as G.S. Item 12.34 ................................................................................................................................ - - - 77.80 - - 07120
07/19
07 ROOFING AND WATERPROOFING 07
Item Item
BITUMINOUS EMULSION ROOFING (CONT'D) Thickness of
base coat
3 mm 5 mm
A B
Per square metre $ $
07121 Surface dressing with clean and sharp sand, one base coat of compound composed of cement, approved bitumen
emulsion and sand (1:8:32) volume.............................................................................................................................................................................. 19.50 23.30 07121
07122 Surface dressing with two coats bitumen based aluminium protective coating.......................................................................................................... 35.00 38.90 07122
07123 Surface dressing with two coats water borne with mineral fibre coloured coating..................................................................................................... 38.90 42.80 07123
REPAIRS TO EXISTING; BITUMINOUS EMULSION ROOFING
A
Per square metre $
07124 Strip and clean off existing bitumen emulsion roofing (any number of coats) complete with any glass fibre membrane
on screed or concrete roofs, and remove from Site including making good surfaces to receive new surfacing if required........................................................ 7.80 07124
07125 Ditto but on corrugated steel or profiled compressed particle sheet (measured flat over corrugations or profiles)..................................................................... 10.80 07125
Per linear metre
07126 Point joints of corrugated steel or profiled compressed particle sheet with approved bitumen emulsion, apply approved cover
coating, apply one coat of approved bitumen emulsion, apply one layer glass fibre membrane and apply two coats
of bitumen emulsion, 150 mm wide............................................................................................................................................................................................... 23.30 07126
SOLAR PROTECTION
A
Per square metre $
07127 Dress surface with bitumen compound and stone chippings......................................................................................................................................................... 27.20 07127
07128 Prepare and apply two coats reflective paint on asphalt surfaces, sloping.................................................................................................................................... 23.30 07128
07129 Ditto, vertical.................................................................................................................................................................................................................. 23.30 07129
REPAIRS TO EXISTING; MASTIC ASPHALT ROOFING
Per square metre A
$
07130 Strip and clean off existing mastic asphalt roofing (any thickness) and associated isolating membrane and reinforcement
on screed or concrete roof, and remove from Site including making good surfaces to receive new surfacing if required.......................................................... 29.10 07130
Each
07131 Cut through complete thickness of mastic asphalt roofing, prepare for inspection by the Maintenance Surveyor in patch
approximately 0.10 m and reseal after inspection the position as directed by the Maintenance Surveyor................................................................................. 51.80 07131
(Note : - This item will only be paid for, if ordered by the Maintenance Surveyor in writing.)
07132 Make good mastic asphalt dressing around pipes, rainwater outlets, etc. and the like................................................................................................................. 12.60 07132
07/20
07 ROOFING AND WATERPROOFING 07
Item Item
PROPRIETARY ROOFING SYSTEM AND FLOOR
Liquid applied
WATERPROOFING SYSTEM Sheet material
material
Apply sheet membrane or liquid applied proprietary roofing system or floor waterproofing system ordered requiring requiring
self self
to the following new or existing surfaces, all in accordance with the manufacturer's instructions : - protec- protec-
finished finished
tion tion
A B C D
Per square metre $ $ $ $
07133 Concrete, screed, asphalt/felt membrane roofing system or floor waterproofing system........................................................ 109.20 134.60 120.10 145.50 07133
07134 Corrugated steel/compressed particle sheet covering roof....................................................................................................... - - 160.10 193.60 07134
07135 Chinese tiled roof (measured flat over tiles) ............................................................................................................................ - - 160.10 193.60 07135
07136 Strip off and clean existing waterproofing roof coverings and associated skirtings, flashings, etc.,
and the like, remove from Site including making good surfaces to receive new surfacing if required.................................. 36.40 36.40 36.40 36.40 07136
A
Per square metre $
07137 Proprietary spray applied high build acrylic waterproofing membrane system comprising primer and top coat, to existing or new
surfaces, including all necessary preparation and protection, all in accordance with the manufacturer's instructions................................................................ 550.10 07137
CANTON TILES AND CONCRETE ROOFING TILES Take Take
Supply down down Fix
Canton tiles and concrete roofing tiles and fitting as BS EN 490 and BS EN 491 : - and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
07138 Tiling laid with 15 mm wide open joints and bedded solid and pointed in cement mortar (1:4) on
screed or roof covering (measured separately) size 300 x 300 x 30 mm thick........................................................................ 82.30 6.40 7.00 12.70 07138
07139 Ditto but bedded, jointed and pointed in hot bitumen.............................................................................................................. 97.80 7.00 7.70 14.60 07139
07140 Tiling laid with 15 mm wide open joints and bedded solid and pointed in cement mortar (1:4) on
screed or roof covering (measured separately) size 400 x 400 x 35 mm thick........................................................................ 89.70 6.40 7.00 11.70 07140
07141 Ditto but bedded, jointed and pointed in hot bitumen.............................................................................................................. 105.20 6.40 7.00 12.70 07141
07/21
07 ROOFING AND WATERPROOFING 07
Item Item
INSULATING ROOFING TILES Take Take
Supply down down Fix
and and and set only
Insulating roofing tiles 300 or 400 mm square and 40 mm thick : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
07142 Tiling laid with 15 mm wide open joints and bedded solid and pointed in cement mortar (1:4) on
screed or roof covering (measured separately)......................................................................................................................... 133.10 6.40 7.00 12.70 07142
07143 Ditto but bedded, jointed and pointed in hot bitumen.............................................................................................................. 143.70 7.00 7.70 14.60 07143
FOAM BOARD ROOFING TILES
Approved concrete foam board roofing tiles of any size and minimum embedded with extruded Take Take
cellular polystyrene foam which is free from halogenated hydrocarbon, CFCs, HCFCs or HFCs Supply down down Fix
Burning behaviour is to be Class B1, non readily ignitable. Maximum compressive load shall not and and and set only
be less than 300 kN m-2. Temperature difference between both sides when tile is heated on one side fix clear aside for
for 1 hour shall not be greater than 15C : - away re-use
A B C D
Per square metre $ $ $ $
07144 Tiling laid with 15 mm wide open joints and bedded solid and pointed in cement mortar (1:4) on
screed or roof covering (measured separately)......................................................................................................................... 192.00 6.40 7.00 19.50 07144
07145 Ditto but bedded, jointed and pointed in hot bitumen.............................................................................................................. 206.40 7.00 7.70 34.10 07145
EXTRUDED POLYSTYRENE FOAM BOARD
Extruded cellular polystyrene foam board shall be free from halogenated hydrocarbon, CFCs, HCFCs or HFCs
Burning behaviour is to be Class B1, non readily ignitable. Density is not less than 33 kg/m. Thermal Thickness (mm)
conductivities are 28, 27,and 27mW.m-1.k-1 for 25 mm, 40 mm and 50 mm thick respectively : - 25 40 50
A B C
Per square metre $ $ $
07146 Extruded cellular polystyrene foam board laid on screed or concrete (measured separately)................................................................... 56.30 79.10 91.70 07146
NON-DESTRUCTIVE TEST
A
Each $
07147 Flooding test in accordance with G.S. Item 12.117....................................................................................................................................................................... 4,286.20 07147
07148 Ditto for inspection of existing roofing system.............................................................................................................................................................................. 4,421.40 07148
07/22
Section 08
CARPENTRY AND JOINERY
08 CARPENTRY AND JOINERY 08
SECTION 08
CARPENTRY AND JOINERY
SPECIAL CONDITIONS
TEMPORARY BARRIERS
Temporary SC08.01 Throughout this Schedule, rates for all trades shall include for all temporary preventive
barriers and protective measures necessary for the execution of the work, such as to protect
new or existing works, and to protect the public from harm, dust or nuisance. No payment
will be made for temporary barriers under any circumstance, with the following exception : -
(a) Temporary barriers specifically ordered by the Maintenance Surveyor in
writing and specifically stating that the temporary barriers are for the exclusive
use of the Employer and other contractor employed directly by the Employer
within the Works Order period.
In the event that the temporary barriers mentioned in sub-clause (a) above are subsequently
used as preventive and protective measures by the Contractor themselves, no payment will
be made.
The temporary barriers shall be measured the length on plan as fixed.
No measurement shall be made for anchor bolts.
Rates for SC08.02 The rates for temporary barriers shall include for : -
temporary
barriers (a) Delivering to and erecting on Site, repairing and maintaining throughout the period
of use in first or subsequent positions, and taking down and setting aside for
re-erection or clearing away.
(b) Providing all materials including poles, struts, cover boarding and the like.
(c) Preparing and applying or touching up paint to all surfaces including writings and
logos in single or multi-colour paints.
(d) Providing and fixing anchor bolts, nuts and washers.
(e) Providing adequate lighting and warning lights and payment of all charges
incurred.
(f) Making good any damage caused to pavings and other surfaces during use,
erection and taking down.
08/1
08 CARPENTRY AND JOINERY 08
SPECIAL CONDITIONS
CARPENTRY AND JOINERY WORK
Measurement SC08.03 All sizes and thicknesses shall be finished sizes and thicknesses.
generally
Measurement SC08.04 Furniture and joinery fittings which are composite items that are fabricated off Site, in
of carpentry whole or substantially in whole, delivered and assembled on Site, shall be measured and
and joinery paid for under Section 20 - Fixtures and Fittings of this Schedule; and shall not be broken
timber down and measured as constituent components. The Schedule rates in this Section of the
Schedule shall not be applied to furniture and joinery fittings, unless otherwise specifically
confirmed by the Maintenance Surveyor in writing.
Carpentry and joinery timber shall be measured as the net length or area fixed, of the
smallest finished square or rectangular section from which the piece can be cut. Timber
members shall be measured flush over joints, no allowance shall be made for tenon and
housing, tongue and groove, and the like at joints.
Fillets, shelving, lining and the like exceeding 150 mm wide and not exceeding 50 mm
thick shall be measured as boarding.
Measurement SC08.05 Boarding, weather boarding, floor boarding, wood block and parquet flooring, plywood
of boarding, and all other building boards, wood wool slabs, wood panels and the like shall all be
flooring, measured as the net area covered when fixed or laid. No deduction shall be made for
plywood, etc. openings not exceeding 0.50 m.
Plywood, plasterboard, fibre insulation board, blockboard, medium density fibreboard,
wood chipboard, laminated plastic decorative sheeting and/or other building boards as
constituent components forming part of a composite item of joinery furniture and fittings
shall not be measured separately.
When stated, the width of boarding shall mean the exposed face width when fixed.
Timber members shall be measured flush over joints, no allowance shall be made for
tenon and housing, tongue and groove, and the like at joints.
Timber boarding shall be measured and rounded up to the nearest 5 mm.
Where teak is supplied and fixed, it will only be paid when specifically ordered by the
Maintenance Surveyor in writing.
Measurement SC08.06 Fibreglass insulating quilts shall be measured as the net area covered. No deduction
of fibreglass quilts shall be made for openings not exceeding 0.50 m.
Measurement SC08.07 Each leaf of doors hung folding or in two heights shall be measured separately.
of folding
doors, etc. Plastic folding doors shall be measured as the net area of the clear opening with
reference to drawing or reference to manufacturer's catalogue excluding any linings,
tracks, rails and the like.
08/2
08 CARPENTRY AND JOINERY 08
SPECIAL CONDITIONS
Ironmongery SC08.08 Ironmongery items can be found in Section 09 - Ironmongery of this Schedule.
items
Measurement SC08.09 Circular windows shall be measured square, semi-circular or segmental portion of
of circular, windows and doors with semi-circular or segmental heads shall be measured
semi-circular rectangular, i.e. net width by net height from springing.
or segmental
heads to doors
and windows
Measurement SC08.10 Measurement of screen fabric and synthetic leather covering shall be the net covered
of screen areas as fixed.
fabric and
synthetic
leather
covering
Measurement SC08.11 Proprietary compact laminate panel as constituent components forming part of a
of proprietary composite item like toilet cubicles, changing room benches, lockers, laboratory
compact laminate benches, fume cupboards and the like shall not be measured separately, unless
panel otherwise specifically ordered by the Maintenance Surveyor in writing.
Measurement SC08.12 Proprietary solid surfacing materials shall be measured as the net plane area inclusive
of proprietary of fittings. The area of any backsplash, bullnose, front apron and inlay or the like shall
solid surfacing not be measured. No deduction shall be made for openings not exceeding 0.50 m.
material
Backsplash, bullnose, front apron and inlay, integral wash basin or sink bowls and the
like shall be measured as Extra over solid surfacing material in which they occur.
The rates for such items shall include the labour and material and other costs
necessary for the items.
Rates generally SC08.13 The rates shall generally include for any or all of the following as applicable : -
(a) Setting out, framing up and straight, raking or circular cutting and waste.
(b) Fixing items complete, true and level including scribing to new or existing work
in any position, fixing in clips or to cramps, embedding in concrete, screeds and
the like, or screwing or bolting to steel. (Special clips, bolts, cutting rebates in
concrete or other surfaces and drilling steel, etc., all measured separately.)
(c) Fixing items in piecing out and replacing existing defective material which has
been cut out and removed. (Cutting out of defective material measured separately.)
(d) Providing all nails, pins, tacks, screws, cups and screws, adhesive, mastics,
white lead and any other fixing and jointing materials.
08/3
08 CARPENTRY AND JOINERY 08
SPECIAL CONDITIONS
Rates generally SC08.13 (e) Notching, cutting and fitting, drilling for screws and boring for bolts including
(Cont'd) (Cont'd) counter-sinking screw, bolt heads and nuts, and pelleting when required.
(f) Executing all plugging required for fixing to new or existing concrete, brick, stone
or other surfaces, with rawplugs or other approved proprietary plugs including
all drilling and cutting mortices or alternatively using Ramset or other similar
approved power operated fixing system.
(g) Narrow widths and small quantities.
(h) Gluing, forming splayed or rounded edges, holes, housing ends, ship-lap joints,
mitres, ends and shaped ends, angles, junctions, heading joints, short lengths
and the like.
(i) Forming tongued angles, chamfers, rebates, grooves and the like.
(j) Forming all mortices and tenons, housed, dovetailed and other framed joints and
providing hardwood or teak pins, wedges, keys and the like when required.
(k) Submission of an authenticated certificate from the Forest Stewardship Council
(FSC) or other approved authority to substantiate the source of supply from a
sustainable forest or plantation.
Rates for SC08.14 The rates for wrot timber shall further include for : -
wrot
timber (a) Punching nail heads, counter sinking screws and the like.
(b) Stopping and sanding to exposed surfaces.
(c) Preparing surfaces for painting or polishing.
(d) In the case of wrot softwood, notwithstanding the botanical classification, it
shall include beech, birch, cherry, chestnut, maple, ash, oak, pine, zen, teak,
mahogany, walnut, aneigre, citron, sapele or sycamore facing.
Rates for SC08.15 The rates for boarding and flooring shall further include for : -
boarding and
flooring (a) Providing and fixing boards in matching widths of any face width required.
(b) Cramping and wedging up if required.
(c) Forming cross-tongued in lieu of tongued and grooved boarding if required.
(d) In the case of tongued and grooved or cross-tongued boarding, ripping off
tongue, cutting back grooves and planning edges flat and square exposed
surfaces.
08/4
08 CARPENTRY AND JOINERY 08
SPECIAL CONDITIONS
Rates for SC08.16 The rates for opening sashes, jalousies and doors shall further include for : -
opening
sashes, (a) Hanging on hinges, rising butts, sliding track, pivots and the like (ironmongery
jalousies measured separately).
and doors
(b) Glazing and glazing beads to framed, panelled and glazed doors.
Rates for SC08.17 The rates for forming observation or vent openings in timber doors shall further
forming include for : -
observation or
vent openings (a) Glazing, glazing beads, hardwood lippings and hardwood louvre
in timber doors blades, etc.
Rates for SC08.18 The rates for flush doors shall further include for : -
flush doors
(a) The use of plywood shall be luan faced internal quality.
(b) The use of beech, birch, cherry, chestnut, maple, ash, oak, pine, zen, teak,
mahogany, walnut, aneigre, citron, sapele or sycamore facing, to flush doors
where hardwood facing is specified.
(c) The use of any thickness of laminated plastic sheet to flush doors where
laminated plastic sheet is specified.
Rates for SC08.19 The rates for proprietary fire resisting doors shall further include for : -
proprietary fire
resisting doors (a) Supply and installation in accordance with the manufacturer's instructions.
(b) Providing and fixing all accessories, ironmongeries (except emergency panic
device with alarm system and digital locking device), intumescent materials
for protection, etc. recommended by the manufacturer.
(c) Providing and fixing door frames where required.
(d) Sealing edges with door seals.
(e) Cutting mortice or drilling in concrete, brick, stone or other surfaces as required.
(f) Grouting into new or existing mortice or holes.
(g) Finishing all surfaces.
(h) Making good disturbed surfaces.
(i) Providing test certificate, operation manual and manufacturer's guarantee as required
by the Maintenance Surveyor for approval or as stated in the Contract.
08/5
08 CARPENTRY AND JOINERY 08
SPECIAL CONDITIONS
Rates for SC08.20 The rates for acoustic doors shall further include for :-
acoustic
doors (a) Supply and installation in accordance with the manufacturer's instructions.
(b) Providing and fixing all accessories, ironmongeries, sound proof/absorbing
materials, etc. recommended by the manufacturer.
(c) Providing and fixing door frames where required.
(d) Sealing door edges with acoustic door seals.
(e) Cutting mortice or drilling in concrete, brick, stone or other surfaces as required.
(f) Grouting into new or existing mortice or holes.
(g) Finishing all surfaces.
(h) Making good disturbed surfaces.
(i) Providing test certificate, operation manual and manufacturer's guarantee as
required by the Maintenance Surveyor for approval or as stated in the Contract.
Rates for SC08.21 The rates for plastic folding doors shall further include for : -
plastic
folding (a) Cutting mortice, sinking or drilling in concrete, brick, stone or other surfaces
doors as required.
(b) Grouting into new or existing mortice or holes.
(c) Providing and fixing with nuts and washers.
(d) Providing and fixing rail, locking device, lock and all necessary ironmongeries.
(e) Making good disturbed surfaces.
Rates for SC08.22 The rates for screen fabric and synthetic leather covering shall further include for : -
screen
fabric and (a) All straight or raking cutting and waste, holes and fittings.
synthetic
leather (b) Executing work in any position, at any height and on new or existing
covering surfaces.
(c) All staples, adhesive and the like.
(d) Covering up and protecting.
08/6
08 CARPENTRY AND JOINERY 08
SPECIAL CONDITIONS
Rates for SC08.23 The rates for proprietary compact laminate panels shall further include for : -
proprietary
compact (a) Supply, fabrication and installation of a compact laminate panel formed
laminate homogeneously under high pressure and high temperature with cellulose fibres or
panels multiple layers of kraft paper of various colours and patterns, all in accordance
with the manufacturer's instructions, to form wall panels, partitions, cladding or
other usage to be approved by the Maintenance Surveyor in writing.
(b) Assembling and erection work either carried out on Site or off-Site.
(c) Submission of certificates of origin, catalogues, technical literature and test
certificates of the compact laminate panel.
(d) Submission of the documentary proof from the manufacturer that the compact
laminate panel to be constructed exhibits acceptable properties of moisture
resistance and/or damage resistance against scratches, graffiti and/or general
wear and tear.
(e) All necessary supporting framework and fixing accessories for completing
the installation of the wall panels, partitions and cladding.
(f) Pointing, jointing and sealing edges with approved sealant, where required.
(g) Submission of samples.
(h) Submission of the manufacturer's warranty of not less than 3 years.
Rates for SC08.24 The rates for proprietary acoustic panels shall further include for :-
proprietary
acoustic (a) Fabric of any thickness complying with flame spread test to BS 476
panels Part 7 : Class 1.
(b) Submission of shop drawings, certificates of origin, catalogues, technical
literature and test certificates.
(c) Provision of samples of acoustic panels showing complete range of colours
and all components.
(d) Preparing mock up as required by and to the approval of the Maintenance
Surveyor.
(e) Providing operation and maintenance manuals, manufacturer's guarantee
and supplier's warranty.
08/7
08 CARPENTRY AND JOINERY 08
SPECIAL CONDITIONS
Rates for SC08.25 The rates for proprietary sport flooring system shall further include for : -
proprietary
sport (a) Submission of shop drawings, certificates of origin, catalogues, technical
flooring literature and test certificates.
system
(b) Provision of samples of flooring showing complete range of colours and all
components.
(c) Preparing mock up as required by and to the approval of the Maintenance
Surveyor.
(d) Provision of operation and maintenance manuals, manufacturer's guarantee
and supplier's warranty.
(e) Applying and obtaining accreditation/certification from recognized international
sports organizations when required.
Rates for SC08.26 The rates for proprietary solid surfacing materials shall further include for : -
proprietary
solid (a) All accessories necessary for the works.
surfacing
material (b) Pointing, jointing and sealing edges with sealant.
(c) Forming holes for pipes, water taps, building services installations, basin,
sink and the like.
(d) Providing and fixing all necessary brackets for sinks, basins and the like.
(e) Submission of catalogues, technical literature, samples, shop drawings and
manufacturer's guarantee.
Rates for SC08.27 The rates for proprietary anti-ricochet surfaces shall further include for :-
proprietary
anti- (a) Supply and installation including all necessary fixing accessories all in
ricochet accordance with manufacturer's instructions.
surfaces
(b) Provision of samples
(c) Provision of technical literature, test certificates, reports, maintenance manuals,
manufacturer's guarantee and supplier's warranty.
08/8
08 CARPENTRY AND JOINERY 08
Item Item
TEMPORARY BARRIERS Erect,
maintain, Erect, Take
take maintain down
down and and
and left-in clear
clear position away
away
A B C
Per cubic metre $ $ $
08001 Sawn hardwood in scantlings and boarding in temporary barriers............................................................................................................ 4,806.50 4,647.10 159.50 08001
Per square metre
08002 25 mm Plywood covering........................................................................................................................................................................... 130.70 125.60 5.10 08002
SCANTLINGS
(Note :- Timber not exceeding 50 mm thick and exceeding 150 mm wide Sectional area (m2)
shall be measured as boarding.) Add to
0.016 m2
for each
Scantlings fixed in grounds, fillets, rafters, trusses, purlins, floor joists, additional
unexposed wall and partition studs, frames, louvre blades, skirtings, n.e. 0.0005 - 0.001 - 0.002 - 0.004 - 0.008 - 0.008 m2
architraves, beads, stops and the like : - 0.0005 0.001 0.002 0.004 0.008 0.016 or part
thereof
in
sectional
area
A B C D E F G
Per linear metre $ $ $ $ $ $ $
08003 Sawn hardwood scantlings.................................................................................................. 4.70 6.00 7.50 10.80 14.20 21.80 6.30 08003
08004 Wrot hardwood scantlings................................................................................................... 8.20 11.90 16.80 26.40 36.90 60.90 20.00 08004
08005 Wrot softwood scantlings.................................................................................................... 8.90 12.90 18.20 28.70 40.10 66.00 21.60 08005
08006 Wrot teak scantlings............................................................................................................ 14.20 21.80 31.10 50.60 80.00 127.20 39.30 08006
Add to either of Items 08003 to 08006 inclusive for scantlings bent to curve to radius n.e. 15 m during fixing by
means of saw cuts, steam bending, etc........................................................................................................................................................................................... 20%
Ditto for scantlings cut curved from solid timber including dowelling and keying sections together.......................................................................................... 35%
08/9
08 CARPENTRY AND JOINERY 08
Item Item
SCANTLINGS (CONT'D) Sectional area (m)
n.e. 0.004 - 0.008 - Exc.
0.004 0.008 0.016 0.016
A B C D
Per linear metre $ $ $ $
08007 Take down and clear away sawn hardwood scantlings / wrot hardwood scantlings /
wrot softwood scantlings / wrot teak scantlings....................................................................................................................... 3.00 5.10 8.30 10.20 08007
08008 Take down and set aside for re-use ditto.................................................................................................................................. 3.20 5.70 9.60 12.10 08008
08009 Fix only ditto including making all joints................................................................................................................................. 6.30 10.10 19.00 25.30 08009
Sawn Sawn
soft- hard- Sawn teak
wood wood
A B C
Per square metre $ $ $
08010 Plane and sand down surface of existing scantlings in position to produce
wrot face including punching nail heads as necessary............................................................................................................................... 45.60 46.90 73.50 08010
BOARDING
Boarding in coverings, linings, window reveals and similar positions,
including weather boarding, exceeding 150 mm in width and not Thickness (mm)
exceeding 50 mm thick : - 15 20 25 30 40 45 50
A B C D E F G
Per square metre $ $ $ $ $ $ $
08011 Sawn hardwood boarding.................................................................................................... 43.70 50.30 57.80 67.80 84.20 95.70 99.80 08011
08012 Wrot hardwood boarding..................................................................................................... 117.70 132.50 154.70 171.00 216.10 242.30 260.40 08012
08013 Ditto tongued and grooved.................................................................................................. 153.10 168.60 183.40 198.20 227.80 247.50 263.90 08013
08014 Ditto tongued, grooved and "V" or bead jointed one face.................................................. 164.90 180.50 195.30 210.10 239.70 254.60 269.40 08014
08015 Ditto tongued, grooved and "V" or bead jointed both faces............................................... 167.10 183.30 198.80 214.30 245.40 260.80 276.40 08015
08/10
08 CARPENTRY AND JOINERY 08
Item Item
BOARDING (CONT'D)
Boarding in coverings, linings, window reveals and similar positions,
including weather boarding, exceeding 150 mm in width and not
exceeding 50 mm thick : - (Cont'd) Thickness (mm)
15 20 25 30 40 45 50
A B C D E F G
Per square metre $ $ $ $ $ $ $
08016 Wrot softwood boarding...................................................................................................... 126.70 142.80 164.10 180.60 225.70 252.30 266.60 08016
08017 Ditto tongued and grooved.................................................................................................. 163.00 176.90 193.50 208.40 239.20 257.70 274.10 08017
08018 Ditto tongued, grooved and 'V' or bead jointed one face.................................................... 173.70 190.50 205.50 220.20 251.00 265.90 281.20 08018
08019 Ditto tongued, grooved and 'V' or bead jointed both faces................................................. 177.60 193.70 209.40 224.90 257.30 272.00 288.90 08019
08020 Wrot teak boarding.............................................................................................................. 223.40 273.30 323.30 373.30 473.20 523.20 573.10 08020
08021 Ditto tongued and grooved.................................................................................................. 262.50 315.00 367.50 419.90 524.90 577.30 629.80 08021
08022 Ditto tongued, grooved and "V" or bead jointed one face.................................................. 273.90 326.40 378.90 431.30 536.30 588.70 641.20 08022
08023 Ditto tongued, grooved and "V" or bead jointed both faces............................................... 281.40 336.40 391.30 446.30 556.20 611.20 666.20 08023
Add to either of Items 08011 to 08023 inclusive for boarding bent to curve to radius n.e. 15 m during
fixing by means of saw cuts, steam bending, etc............................................................................................................................................................................ 20%
Ditto for boarding cut curved from solid timber including dowelling and keying sections together..............................................................................................................................................
35%
Sawn Wrot
Wrot
hard- hard-
teak
wood wood
A B C
Per square metre $ $ $
08024 Plane and sand down surface of existing boarding in position to produce wrot face including
punching nail heads as necessary................................................................................................................................................................ 46.90 32.90 51.90 08024
08/11
08 CARPENTRY AND JOINERY 08
Item Item
BOARDING (CONT'D) Tongued
Square
and
edge
grooved
boarding
boarding
A B
Per square metre $ $
08025 Take down and clear away existing sawn hardwood / sawn softwood / sawn teak
/wrot hardwood / wrot softwood / wrot teak boarding of any thickness...................................................................................................................... 14.70 15.30 08025
08026 Take down and set aside for re-use ditto...................................................................................................................................................................... 17.90 28.70 08026
08027 Fix only ditto................................................................................................................................................................................................................. 69.70 101.30 08027
Hard- Soft-
Teak
wood wood
A B C
Per linear metre $ $ $
08028 Forming rebate, groove, splay, chamfer, bead, rounded angle, tongue, flute, cove, moulding or similar labour
on existing boarding in position.................................................................................................................................................................. 6.30 8.90 10.10 08028
08029 Ditto but circular to radius n.e. 15.00 m..................................................................................................................................................... 10.10 16.50 21.50 08029
STRIP FLOORING Soft-
Teak
wood
A B
Per square metre $ $
08030 Flooring of 20 mm thick in any size wood strips matched for colour, tongued, grooved and "V" jointed all round and
laid in basket or herringbone pattern with straight borders as ordered, laid on bitumen/rubber latex waterproofing
emulsion coated screed or blockboard backing (paint, screed and blockboard backing measured separately),
including preparing surface for polishing..................................................................................................................................................................... 451.60 556.80 08030
08031 Take up and clear away wood strip flooring (blockboard backing measured separately)........................................................................................... 21.10 21.10 08031
08032 Take up and set aside for re-use wood strip flooring (ditto)........................................................................................................................................ 31.90 31.90 08032
08033 Lay only wood strip flooring (ditto).............................................................................................................................................................................. 190.00 190.00 08033
WOOD BLOCK FLOORING Thickness (mm)
20 25 20 25
Softwood Teak
A B C D
Per square metre $ $ $ $
08034 Flooring of the stated thickness in any size wood blocks matched for colour, tongued and grooved all round
and laid in basket or herringbone pattern with straight borders as ordered, fixed with cold bitumen/rubber
emulsion adhesive to screeds, including preparing surfaces for polishing.............................................................................. 162.50 189.40 188.20 227.30 08034
08035 Take up and clear away wood block flooring........................................................................................................................... 12.80 16.00 16.00 19.10 08035
08036 Take up and set aside for re-use wood block flooring.............................................................................................................. 17.90 21.10 21.10 24.20 08036
08037 Lay only wood block flooring................................................................................................................................................... 76.00 82.30 76.00 82.30 08037
08/12
08 CARPENTRY AND JOINERY 08
Item Item
PARQUET FLOORING Hard- Soft-
Teak
wood wood
A B C
Per square metre $ $ $
08038 Parquet flooring of 8 mm thick in any size wood blocks matched for colour, tongued and groove and laid in pattern
as ordered, fixed with cold bitumen/rubber emulsion adhesive to screeds, including preparing surfaces for polishing......................... 95.40 102.40 107.20 08038
08039 Take up and clear away parquet flooring.................................................................................................................................................... 10.90 14.00 14.00 08039
08040 Take up and set aside for re-use parquet flooring...................................................................................................................................... 16.00 21.10 21.10 08040
08041 Lay only parquet flooring............................................................................................................................................................................ 44.30 44.30 44.30 08041
A
Per square metre $
08042 Plane as necessary, sand down, clean off existing wood block or parquet flooring of any type and prepare surface for polishing............................................ 16.50 08042
LAMINATED FLOORING
Laminated flooring of various series comprising laminated planks, pre-finished, tongued and grooved and laid in the Boarding
required pattern including sub-floor with approved bitumen/rubber latex waterproofing emulsion, fibreglass or thickness (mm)
polyethylene backing as required all in accordance with the manufacturer's recommendations : - n.e. 10 exc. 10
A B
Per square metre $ $
08043 Laminated flooring........................................................................................................................................................................................................ 234.50 266.80 08043
08044 Take up and clear away laminated flooring complete with sub-flooring..................................................................................................................... 23.30 23.30 08044
08045 Take up and set aside for re-use ditto........................................................................................................................................................................... 18.20 18.20 08045
08046 Fix only ditto................................................................................................................................................................................................................. 45.60 63.30 08046
A
Per linear metre $
08047 Aluminium T-strip cover for expansion joint................................................................................................................................................................................. 97.00 08047
08048 Aluminium end edging strip........................................................................................................................................................................................................... 63.80 08048
08049 Laminated skirting n.e. 100 mm high............................................................................................................................................................................................. 88.90 08049
08/13
08 CARPENTRY AND JOINERY 08
Item Item
SASHES
Sashes for solid or cased frames, fanlights, lanterns and skylights, etc., with styles, head and bottom rails of required widths,
divided into squares of any size with glazing bars including all rebates, splays, throats, mouldings and similar labours
(solid or cased frames, glass, glazing beads and ironmongery all measured separately) : -
Thickness (mm)
40 45 50 55 65
A B C D E
Per square metre $ $ $ $ $
08050 Fixed wrot hardwood sash including screwing to frame and bedding in white lead if required........................... 385.80 401.70 417.20 433.60 464.70 08050
08051 Ditto but wrot softwood.......................................................................................................................................... 526.10 549.70 573.50 598.70 646.00 08051
08052 Ditto but wrot teak................................................................................................................................................... 539.60 567.60 596.00 625.40 681.80 08052
08053 Opening wrot hardwood sash including hanging or hanging folding on hinges, pivots or to
slides vertically or horizontally, providing and fixing parting beads and stops required...................................... 430.60 447.00 464.40 480.90 515.50 08053
08054 Ditto but wrot softwood.......................................................................................................................................... 547.10 570.70 595.60 618.80 668.20 08054
08055 Ditto but wrot teak................................................................................................................................................... 598.60 628.40 659.80 689.40 751.60 08055
JALOUSIES
Per square metre
08056 Wrot hardwood jalousie with fixed wood louvre blades at angle of 45 degrees rounded or splayed
on edges and spaced at about 40 mm centres, framed up in panels with styles, head and bottom
rails of required widths including all rebates, splays, throats, mouldings and similar labours,
louvre blades notched and housed into styles and secured with small fillet around back
edges of styles, and hanging or hanging folding (ironmongery measured separately).......................................... 485.70 498.50 510.50 521.90 545.40 08056
08057 Ditto but wrot softwood.......................................................................................................................................... 621.30 636.30 652.90 669.00 702.00 08057
08058 Ditto but wrot teak................................................................................................................................................... 682.00 700.90 721.60 742.00 783.20 08058
08059 Wrot hardwood jalousie with wood louvre blades movable and spaced at about 65 mm centres
pivoted into styles and movable operating bar secured to louvres with pairs of eyes, framed up
in panels with styles, head and bottom rails of required widths including all rebates, splays, throats,
mouldings and similar labours, louvre blades notched and housed into styles and secured with
small fillet around back edges of styles, and hanging or hanging folding
(ironmongery measured separately)........................................................................................................................ 631.90 646.70 659.20 671.80 696.60 08059
08060 Ditto but wrot softwood.......................................................................................................................................... 790.60 808.40 825.50 834.60 878.30 08060
08061 Ditto but wrot teak................................................................................................................................................... 847.90 869.90 891.60 901.80 957.60 08061
Add to either of Items 08050 to 08061 inclusive for semi-circular, segmental or elliptical head to rectangular sash or jalousie (circular sash
measured square, semi-circular, segmental or elliptical portion only measured rectangular net width by net height from springing)....................................... 35%
08/14
08 CARPENTRY AND JOINERY 08
Item Item
FRAMED, PANELLED AND GLAZED DOORS
Framed, panelled and glazed doors with styles, muntin, head, intermediate and bottom rails
of required widths and 20 mm thick panels, wholly or partly glazed, including semi-circular, Wrot hardwood
segmental, or elliptical head etc, and hanging (ironmongery measured separately) : - Overall door thickness (mm)
40 45 50 55 65
A B C D E
Per square metre $ $ $ $ $
08062 Door square and flat both sides............................................................................................................................... 452.60 477.40 497.50 512.10 555.00 08062
SOLID DOORS Wrot hardwood
Overall door thickness (mm)
40 45 50 55 65
A B C D E
Per square metre $ $ $ $ $
08063 Solid door of tongued and grooved boarding clamped with and including three 16 mm diameter
horizontal mild steel rods each 15 mm shorter than door width and threaded and fitted with nuts
and washers both ends, drilling boarding for rods, countersinking for nuts, pelleting, "V" or
bead jointed to one or both sides and hanging (ironmongery measured separately)............................................. 479.40 521.00 560.90 591.50 669.60 08063
FLUSH DOORS
Flush doors lipped all round with 12 mm selected hardwood lipping and lipped meeting
Overall door thickness (mm)
edge with 25 mm selected hardwood lipping. (ironmongery measured separately) : -
25 30 40 45 50
A B C D E
Per square metre $ $ $ $ $
08064 Hollow core flush door covered both sides with 3.2 mm standard hardboard....................................................... 173.80 190.20 208.00 247.50 274.70 08064
08065 Extra over Item 08064 for cover one side with 5 mm plywood............................................................................. 67.70 67.70 67.70 67.70 67.70 08065
08066 Extra over Item 08064 for cover one side with 5 mm hardwood faced plywood.................................................. 61.10 61.10 61.10 61.10 61.10 08066
08067 Extra over Item 08064 for cover one side with laminated plastic sheet................................................................ 70.90 70.90 70.90 70.90 70.90 08067
08068 Solid core flush door covered both sides with 3.2 mm standard hardboard.......................................................... 215.90 236.20 258.40 270.50 302.60 08068
08069 Extra over Item 08068 for cover one side with 5 mm plywood............................................................................. 67.70 67.70 67.70 67.70 67.70 08069
08070 Extra over Item 08068 for cover one side with 5 mm hardwood faced plywood.................................................. 61.10 61.10 61.10 61.10 61.10 08070
08071 Extra over Item 08068 for cover one side with laminated plastic sheet................................................................ 70.90 70.90 70.90 70.90 70.90 08071
08072 Add to either of Items 08062, 08063, 08064 and 08068 if door hung folding or in two heights
including rebates, beads and additional thickness of edge fillet required............................................................. 19.50 21.10 23.70 25.00 26.80 08072
Each
08073 Extra over either of Items 08064 to 08071 inclusive for forming observation or vent panel
opening n.e. 0.20 m (net opening size) through hollow or solid core flush door................................................. 67.70 75.40 80.50 88.00 91.80 08073
08074 Ditto but opening 0.20 - 0.40 m............................................................................................................................. 99.00 109.70 121.40 131.40 138.00 08074
08/15
08 CARPENTRY AND JOINERY 08
Item Item
PROPRIETARY FIRE RESISTING DOORS
Supply and fix proprietary fire resisting timber doors tested in accordance with BS 476 : Pt. 20-23
Fire rated period
including any finish : -
hour 1 hour 1 hours 2 hours
A B C D
Per square metre $ $ $ $
(door panel size measured net)
08075 Single leaf fire resisting door without door frames.................................................................................................................. 1,181.60 1,574.80 1,969.00 2,373.70 08075
08076 Ditto, with door frames............................................................................................................................................................. 1,392.10 2,057.50 2,739.00 3,409.30 08076
08077 Double leaf fire resisting door without door frames................................................................................................................. 856.10 1,250.80 1,648.40 2,045.60 08077
08078 Ditto, with door frames............................................................................................................................................................. 1,099.30 1,617.90 2,136.00 2,673.60 08078
Per linear metre
08079 Smoke and intumescent seals, tested in accordance with BS 476 : Pt. 20 - 23....................................................................... 117.90 117.90 117.90 117.90 08079
Each
08080 Extra over either of Items 08075 to 08078 inclusive for forming observation panel opening n.e. 0.20 m
(net opening size) through fire resisting timber flush door ..................................................................................................... 67.70 75.40 80.50 88.00 08080
08081 Ditto but opening 0.20 - 0.40 m............................................................................................................................................... 99.00 109.70 121.40 131.40 08081
Each or per leaf
08082 Take down and clear away fire resisting door without door frames........................................................................................ 14.70 14.70 14.70 14.70 08082
08083 Take down and clear away fire resisting door with and including door frames...................................................................... 21.70 21.70 21.70 21.70 08083
08084 Take down and set aside for re-use fire resisting door without door frames........................................................................... 33.80 33.80 33.80 33.80 08084
08085 Take down and set aside for re-use fire resisting door with and including door frames......................................................... 59.30 59.30 59.30 59.30 08085
08086 Fix only fire resisting door without door frames...................................................................................................................... 406.60 406.60 406.60 406.60 08086
08087 Fix only fire resisting door with and including door frames.................................................................................................... 867.70 867.70 867.70 867.70 08087
(Note : - The above Items 08075 to 08087 inclusive will only be paid for if ordered in writing by the Maintenance Surveyor.)
ACOUSTIC DOORS
Door
Approved acoustic doors including any finish : - with without
frames frames
Per square metre A B
(door panel size measured net) $ $
08088 Single leaf acoustic door complete with acoustic seal assembly................................................................................................................................. 5,836.80 5,338.20 08088
08089 Double leaf acoustic door complete with ditto............................................................................................................................................................. 4,864.00 4,399.30 08089
08090 Take down and clear away acoustic door..................................................................................................................................................................... 25.30 16.50 08090
08091 Take down and set aside for re-use acoustic door........................................................................................................................................................ 67.10 40.50 08091
08092 Fix only acoustic door................................................................................................................................................................................................... 1,013.40 461.10 08092
(Note : - The above Items 08088 to 08092 inclusive will only be paid for, if ordered in writing by the Maintenance Surveyor.)
08/16
08 CARPENTRY AND JOINERY 08
Item Item
REPAIRS, ETC., TO SASHES, JALOUSIES AND DOORS
Jalousie Jalousie
Cup-
Execute the following to hardwood, softwood or teak sashes, Fixed Opening with with Solid Flush
board
jalousies, drawers and doors of any size and thickness, single or sash sash fixed movable door door
door
folding (any new ironmongery measured separately) : - louvres louvres
A B C D E F G
Each or per leaf $ $ $ $ $ $ $
08093 Take down (complete with ironmongery, sash cords, etc., required)
and clear away..................................................................................................................... 17.90 17.90 20.40 20.40 26.80 26.80 14.70 08093
08094 Take down and set aside for re-use..................................................................................... 19.10 19.10 23.60 23.60 33.80 33.80 21.70 08094
08095 Fix only including screwing to frame and bedding in white lead
if required............................................................................................................................. 22.80 - - - - - - 08095
08096 Hang only including fixing any sash cord, etc.................................................................... - 18.70 23.30 23.30 37.20 37.20 23.10 08096
08097 Ease and adjust in position including re-securing, tightening existing
or providing new screws to hinges, pivots, sliding gear, etc., cleaning
and oiling the same, and planning, sanding down, painting one coat
of hard gloss paint and polishing edges as required.......................................................... - 11.90 14.80 14.80 18.70 18.70 14.80 08097
08098 Ditto but including taking down and afterwards re-fixing................................................. - 57.80 72.40 72.40 106.80 106.80 68.60 08098
08099 Repair angle or junction of framing with and including 150 x 150 x 25 x 5 mm
galvanized steel flat tee or angle, let in flush and screwed (per angle or tee).................... - 26.00 26.00 26.00 26.00 - - 08099
08100 Clamp up and repair or re-make joint with glue or white lead
including re-wedging or re-pinning with new wedges or pins if
required (taking down and re-hanging measured separately)............................................. 38.30 38.30 74.10 74.10 20.30 - - 08100
08101 Ditto but including taking down, removing or cutting out defective
parts and preparing to receive new parts (new parts measured
separately as boarding, fillets, plywood, etc., supplied and fixed
under the appropriate schedule items)................................................................................ 123.90 123.90 205.10 205.10 126.70 - - 08101
A
Per linear metre $
08102 Provide and fix new 16, 22 or 29 mm circumference white Manila or other approved sash cord............................................................................................... 8.00 08102
Each
08103 Small hardwood pieces let in or plug holes for making good where door fitting has been removed from sash or door frames, doors,
sashes, etc. including painting patch to match existing................................................................................................................................................................. 13.10 08103
(Note : - This item will not be paid for, if removal of door fitting and making good have been measured elsewhere.)
08/17
08 CARPENTRY AND JOINERY 08
Item Item
TIMBER FRAMES TO WINDOWS, DOORS, PARTITIONS AND PANELS
Timber frames to windows, doors, exposed partition or panel frames, transoms, mullions, styles, rails or cills, etc., framed up and fixed complete
including rebates, grooves, throats, rounded angles, chamfers, splays, mouldings on solid and similar labours and all framed joints : -
Wrot hardwood Wrot teak
Thickness (mm) Thickness (mm)
30 50 65 75 90 100 30 50 65 75 90 100
A B C D E F G H I J K L
Per linear metre $ $ $ $ $ $ $ $ $ $ $ $
08104 Width n.e. 50 mm....................... - 21.70 24.50 26.50 29.90 32.30 - 36.10 42.00 45.40 52.30 56.40 08104
08105 Width 50 - 100 mm.................... 21.30 29.30 35.20 39.50 45.20 49.20 35.30 50.90 62.50 71.50 83.60 90.30 08105
08106 Width 100 - 150 mm.................. 30.60 44.30 53.50 60.60 69.90 75.70 53.40 82.10 102.70 114.50 133.60 149.10 08106
08107 Width 150 - 200 mm.................. 41.80 59.10 74.10 83.30 94.00 103.60 77.50 115.90 148.70 166.40 188.20 210.70 08107
Timber frames to windows, doors, exposed partition or panel frames, transoms,
mullions, styles, rails or cills, etc., framed up and fixed complete including rebates, Wrot softwood
grooves, throats, rounded angles, chamfers, splays, mouldings on solid and similar Thickness (mm)
labours and all framed joints : - 30 50 65 75 90 100
A B C D E F
Per linear metre $ $ $ $ $ $
08108 Width n.e. 50 mm.................................................................................................................................. - 30.70 33.90 36.10 45.90 46.40 08108
08109 Width 50 - 100 mm................................................................................................................................ 29.70 41.50 50.30 56.60 64.10 71.30 08109
08110 Width 100 - 150 mm............................................................................................................................. 44.40 63.20 75.60 89.30 100.20 110.90 08110
08111 Width 150 - 200 mm............................................................................................................................. 59.50 89.10 109.30 123.70 142.00 158.40 08111
Add to either of Items 08104 to 08111 inclusive for frames, etc., bent to curve to radius n.e. 15 m during fixing
by means of saw cuts, steam bending, etc...................................................................................................................................................................................... 20%
Ditto for frames, etc., cut circular from solid timber including dowelling and keying sections together..................................................................................... 35%
08/18
08 CARPENTRY AND JOINERY 08
Item Item
TIMBER FRAMES TO WINDOWS, DOORS, PARTITIONS AND PANELS (CONT'D)
Timber frames to windows, doors, exposed partition or panel frames, transoms, mullions, styles, rails or cills, etc., framed up
and fixed complete including rebates, grooves, throats, rounded angles, chamfers, splays, mouldings on solid and similar
labours and all framed joints : - (Cont'd)
A
Per linear metre $
08112 Take down and clear away wrot hardwood / wrot softwood / wrot teak frames to windows, doors,
exposed partition or panel frames, transoms, mullions, styles, rails or cills, etc., of any size....................................................................................................... 10.20 08112
08113 Take down and set aside for re-use ditto........................................................................................................................................................................................ 16.50 08113
08114 Fix only ditto................................................................................................................................................................................................................................... 18.20 08114
A
Each $
08115 Repair angle or junction of frames, etc., with and including 150 x 150 x 25 x 5 mm galvanized steel flat tee or angle, let in flush
and screwed (per angle or tee)........................................................................................................................................................................................................ 24.50 08115
08116 Clamp up and repair or re-make joint with glue or white lead including re-wedging or re-pinning with new wedges or pins if
required (taking down and re-fixing measured separately)............................................................................................................................................................ 25.40 08116
PLASTIC FOLDING DOORS
Plastic folding doors in any colour and series including door frames and all necessary accessories, screwed to wood or plugged
and screwed to concrete, brickwork and the like in accordance with the manufacturer's recommendations : -
A
Per square metre $
(door panel size measured flat)
08117 Plastic folding door......................................................................................................................................................................................................................... 218.60 08117
SCREEN FABRIC
Screen fabric of 1.5 mm thick in any colours covered to panel or backing (panel or backing measured separately) : - Take
Supply down
and and
fix clear
away
A B
Per square metre $ $
08118 Screen fabric.................................................................................................................................................................................................................. 131.60 31.40 08118
08/19
08 CARPENTRY AND JOINERY 08
Item Item
SYNTHETIC LEATHER Take
Supply down
Synthetic leather of n.e. 3 mm thick in any colours covered to panel or backing and and
(panel or backing measured separately) :- fix clear
away
A B
Per square metre $ $
08119 Synthetic leather covering with 5 mm foam................................................................................................................................................................. 363.70 22.20 08119
08120 Synthetic leather covering without 5 mm foam............................................................................................................................................................ 316.20 16.60 08120
STAIRCASES Wrot hardwood Wrot teak
Thickness (mm) Thickness (mm)
20 25 30 40 50 20 25 30 40 50
A B C D E F G H I J
Per square metre $ $ $ $ $ $ $ $ $ $
08121 Tread (including winder tread) with
rounded nosing, grooved for risers and
wedged, glued, blocked and fixed complete
(exposed top surface area measured)............................. - - 232.80 304.40 358.70 - - 405.20 536.10 637.60 08121
08122 Riser (including winder riser) with rebated
or tongued edges, and wedged, glued and
fixed complete (exposed face area measured)............... 168.40 197.90 221.60 - - 289.90 351.60 394.10 - - 08122
Wrot
Wrot
hard -
teak
wood
A B
Per linear metre $ $
08123 Rounded or "mopstick" handrail n.e. 0.004 m sectional area, framed and fixed level or raking, housed for balusters or
rung for metal core rail, tenoned to newel posts, and jointed with and including double nut handrail screws, including
splayed or rounded ends................................................................................................................................................................................................ 59.00 89.10 08123
08124 Ditto ramped or circular................................................................................................................................................................................................ 60.70 91.70 08124
08125 Ditto wreathed............................................................................................................................................................................................................... 62.30 93.70 08125
08126 Add to either of Items 08123 to 08125 inclusive for each additional 0.001 m or part thereof in sectional area...................................................... 14.60 21.70 08126
08127 Handrail n.e. 0.004 m sectional area all as last described but moulded to detail....................................................................................................... 61.90 94.80 08127
08128 Ditto ramped or circular................................................................................................................................................................................................ 63.80 97.10 08128
08129 Ditto wreathed............................................................................................................................................................................................................... 68.10 108.10 08129
08130 Add to either of Items 08127 to 08129 inclusive for each additional 0.001 m or part thereof in sectional area...................................................... 16.60 25.40 08130
08131 75 x 30 or 40 mm Rounded nosing fixed to edge of landing to match stair tread nosing, rebated to match thickness of
flooring, and tongued and grooved to the same............................................................................................................................................................ 61.90 86.50 08131
08/20
08 CARPENTRY AND JOINERY 08
Item Item
REPAIRS TO STAIRCASES Take Take
down down Fix
Execute the following to hardwood or teak staircase parts of any size and thickness : - and and set only
clear aside for
away re-use
A B C
Per square metre $ $ $
08132 Treads and risers complete with wedges and blocks if required................................................................................................................ 23.00 33.80 89.90 08132
Per linear metre
08133 String of any type, straight or to any sweep................................................................................................................................................ 20.40 31.90 100.10 08133
08134 Handrail ditto............................................................................................................................................................................................... 10.80 20.40 35.50 08134
Each
08135 Baluster........................................................................................................................................................................................................ 15.30 15.90 24.10 08135
08136 Newel post complete with cap or pendant if any........................................................................................................................................ 16.60 16.60 29.10 08136
Wrot hardwood Wrot teak
Thickness (mm) Thickness (mm)
30 40 50 30 40 50
A B C D E F
Per linear metre $ $ $ $ $ $
08137 Cut out tread nosing for width of about 125 mm and clear away and
provide and fix new nosing glued and dowelled to existing tread....................................................... 61.40 74.50 83.40 82.50 106.10 121.10 08137
08/21
08 CARPENTRY AND JOINERY 08
Item Item
SUNDRY ITEMS Wrot
Wrot
hard-
teak
wood
A B
Per linear metre $ $
08138 Curtain pole 40 mm to 50 mm diameter with ends turned to 65 mm diameter and fixing......................................................................................... 69.40 103.70 08138
Each
08139 Turned caps and knobs 25 mm diameter and fixing.................................................................................................................................................... 15.30 18.70 08139
08140 Ditto but 50 mm diameter............................................................................................................................................................................................. 19.50 24.90 08140
08141 Ditto but 75 mm diameter............................................................................................................................................................................................. 27.90 37.50 08141
08142 Hatpegs of any length or size, square, shaped or turned.............................................................................................................................................. 12.20 14.80 08142
08143 Square or rectangular blocks with chamfered edges n.e. 40 mm thick for latches, bell pushes, door stops and the like,
and fixing ...................................................................................................................................................................................................................... 17.50 21.50 08143
08144 Circular ditto................................................................................................................................................................................................................. 21.30 28.50 08144
08145 25 mm Thick backboard to cistern n.e. 450 x 300 mm chamfered all round and fixing............................................................................................. 50.30 - 08145
SUNDRY LABOURS Diameter or average
length of side (mm)
Each
additional
n.e. 50 50 - 100 100 mm
or part
thereof
A B C
Each $ $ $
08146 Bore or cut round hole through hardwood or teak n.e. 25 mm thick......................................................................................................... 4.50 7.70 5.10 08146
08147 Add to Item 08146 for each additional 25 mm or part thereof in thickness.............................................................................................. 3.20 6.40 3.80 08147
08148 Cut square or rectangular hole through hardwood or teak n.e. 25 mm thick............................................................................................. 5.10 7.70 5.70 08148
08149 Add to Item 08148 for each additional 25 mm or part thereof in thickness.............................................................................................. 3.80 5.10 4.50 08149
A
Each $
08150 Cut oval shaped hole with rounded edges through timber or plywood for latrine seat................................................................................................................. 19.00 08150
08151 Cut dishes housing in timber for rifle butt and the like................................................................................................................................................................. 9.60 08151
08152 Cut rounded notch in timber for rifle, revolver barrel and the like................................................................................................................................................ 3.80 08152
08153 Cut pointed or rounded head to fencing post................................................................................................................................................................................. 3.80 08153
08/22
08 CARPENTRY AND JOINERY 08
Item Item
BUILDING BOARDS AND SUNDRY ITEMS
PLYWOOD Thickness (mm)
n.e. 6 9 12 15 18
A B C D E
Per square metre $ $ $ $ $
08154 Grade 2 plywood, internal quality, luan faced, finished for painting or polishing if
required, and fixed with nails, panel pins, screws or adhesive as ordered, in wall
or ceiling lining, doors, or any other position......................................................................................................... 58.90 67.00 78.00 84.50 99.00 08154
08155 Grade 2 plywood, external quality, luan faced, finished for painting or polishing if
required, and fixed with nails, panel pins, screws or adhesive as ordered, in wall
or ceiling lining, doors, or any other position......................................................................................................... 72.80 82.70 96.30 104.30 122.30 08155
A
Per square metre $
08156 Extra over either of Items 08154 to 08155 inclusive for hardwood facing including teak, beech, maple, oak,
zen wood, aneigre wood, sycamore wood and similar facing of natural finish to one side of plywood....................................................................................... 37.50 08156
Thickness (mm)
9 18
A B
Per square metre $ $
08157 Marine plywood as G.S. item 13.13 bonded with W.B.P. adhesive between plys, finished for painting or polishing if required,
and fixed with nails, panel pins, screws or adhesive as ordered, in wall or ceiling lining, doors, or any other position........................................... 92.40 128.90 08157
PLASTERBOARD Thickness (mm)
9.50 12.50
A B
Per square metre $ $
08158 Plasterboard of "gypsum base board" or "gypsum lath", fixed with nails panel pins, screws or adhesive as ordered, in walls
or any other vertical position......................................................................................................................................................................................... 64.10 69.00 08158
08159 Ditto in soffits, or any other sloping or horizontal position......................................................................................................................................... 70.50 75.10 08159
FIBRE INSULATION BOARD Thickness (mm)
9 12 19
A B C
Per square metre $ $ $
08160 Natural finish fibre insulating board fixed with nails, screws or adhesive as ordered, in wall or ceiling lining,
position, including chamfered edges to boards and fixing in symmetrical patterns if required................................................................ 53.20 56.80 68.90 08160
08/23
08 CARPENTRY AND JOINERY 08
Item Item
BLOCKBOARD AND MEDIUM DENSITY FIBREBOARD (MDF) Blockboard MDF
Grade 2 veneer Moisture resistant
bonded with grade as G.S.
Type M.R. 13.17.1 including
adhesive as G.S. plain or
13.14 with luan melamine faced
faced both sides boarding
Thickness (mm) Thickness (mm)
15 18 15 18
A B C D
Per square metre $ $ $ $
08161 Boarding in coverings, linings and similar position................................................................................................................. 84.50 97.30 67.30 77.40 08161
WOOD CHIPBOARD Thickness (mm)
9 12 18 32
A B C D
Per square metre $ $ $ $
08162 Wood chipboard fixed with nails, screws, or adhesive as ordered, in wall or ceiling lining,
doors, or any other position....................................................................................................................................................... 50.30 56.80 65.60 89.10 08162
08163 Ditto but faced for painting one side........................................................................................................................................ - 80.50 93.30 - 08163
08164 Ditto but faced for painting both sides..................................................................................................................................... - 92.10 113.70 - 08164
08165 Ditto but faced one side with and including laminated decorative plastic sheeting (Class VG
or HG as specified) ................................................................................................................................................................... - 137.90 153.00 - 08165
LAMINATED PLASTIC DECORATIVE SHEETING
Laminated plastic decorative sheeting fixed with adhesive to bench tops, doors or any other position : - Thickness (mm)
0.7 1.0 1.3
A B C
Per square metre $ $ $
08166 Standard laminated plastic decorative sheeting (Class HG or VG as specified)....................................................................................... 98.40 142.10 174.90 08166
A
Per square metre $
08167 1.3 mm Thick laminated plastic decorative sheeting cigarette proof or chemical resistance....................................................................................................... 165.90 08167
08168 0.7 mm (Overall) thick laminated plastic decorative sheeting (raw finished wood grains series)................................................................................................ 201.10 08168
08169 Ditto (PU finished wood grains series)........................................................................................................................................................................................... 250.90 08169
08170 0.8 mm Thick laminated decorative sheeting faced with polished finish aluminium sheet fixed with adhesive to bench
tops, doors or any position.............................................................................................................................................................................................................. 196.50 08170
08171 1.3 mm (Overall) thick laminated plastic in aluminium sheet with engraved pattern, in stainless steel or copper finish fixed
with adhesive to bench tops, doors or any position........................................................................................................................................................................ 335.50 08171
08172 Ditto brushed aluminium finish ditto............................................................................................................................................................................................. 342.20 08172
08/24
08 CARPENTRY AND JOINERY 08
Item Item
PROPRIETARY COMPACT LAMINATE PANELS
(Note : - The following Item 08173 will only be paid for, if ordered by the Maintenance
Surveyor in writing.) Thickness (mm)
3 6 8 9 12
A B C D E
Per square metre $ $ $ $ $
08173 Proprietary compact laminate panels in any colours and finishes to form wall panels,
partitions and cladding fixed in any position.......................................................................................................... 356.60 524.10 641.70 934.20 1,189.10 08173
PROPRIETARY ACOUSTIC PANELS
Proprietary acoustic panel fixed to timber or steel framing (framing measured separately) to wall or ceiling in any colours
and finishes complete with all backing and fixing accessories in accordance with the manufacturer's recommendation : -
A
Per square metre $
08174 Acoustic panel system comprising 25 mm thick acoustic panel of high density rigid composite panel fibreglass of density no less than 48kg/m3
and covered with fabric of any thickness....................................................................................................................................................................................... 669.70 08174
08175 Acoustic wooden panel with melamine finish, tile type, grooved or perforation panel in n.e. 20 mm thick MDF, back sides
laminated with acoustic inlay.......................................................................................................................................................................................................... 1,273.40 08175
08176 Acoustic wooden panel with melamine finish, plank type, grooved or perforation panel in n.e. 20 mm thick MDF, back sides
laminated with acoustic inlay.......................................................................................................................................................................................................... 1,091.50 08176
08177 25 mm thick acoustic underlay....................................................................................................................................................................................................... 152.80 08177
08178 50 mm thick acoustic underlay....................................................................................................................................................................................................... 262.00 08178
A
Per linear metre $
08179 Concealed friction fit or interlock PVC track system to wall or ceiling complete with all fixing accessories............................................................................. 109.20 08179
08/25
08 CARPENTRY AND JOINERY 08
Item Item
FLAT FIBROUS REINFORCED CEMENT SHEETING Thickness (mm)
5 6 12
A B C
Per square metre $ $ $
08180 Sheeting butt jointed and fixed to vertical or horizontal timber framing (measured separately) with
30 mm galvanized nails at 300mm centres around all edges..................................................................................................................... 105.50 109.00 149.10 08180
08181 Ditto but fixed to flat or sloping soffits...................................................................................................................................................... 111.50 115.60 155.50 08181
08182 Add to either of Items 08180 to 08181 inclusive if fixed with screws in lieu of nails.............................................................................. 12.30 12.30 12.30 08182
08183 Add to ditto if fixed to steel framing (measured separately) with screws, or bolts, nuts and washers,
including drilling steel and tapping if required.......................................................................................................................................... 5.80 5.90 6.30 08183
Per linear metre
08184 6 mm Thick fibrous reinforced cement cover strip 75 mm wide fixed at joints........................................................................................ 9.70 10.10 13.50 08184
GLAZED FIBROUS REINFORCED CEMENT COLOURED SHEETING
A
Per square metre $
08185 4 mm Thick glazed fibrous reinforced cement coloured sheeting fixed with screws or adhesive in wall or ceiling lining,
fittings, doors, or any other position............................................................................................................................................................................................... 108.60 08185
WOOD WOOL SLABS Thickness (mm)
25 40 50 75
A B C D
Per square metre $ $ $ $
08186 Slabs set on edge or end, and jointed in cement/lime mortar if required in partition including
building in panels between timber or other framing if necessary............................................................................................ 60.00 96.00 120.00 162.00 08186
08/26
08 CARPENTRY AND JOINERY 08
Item Item
SUNDRY LABOURS
Girth of hole or
(Note : - The following Items 08187 to 08188 inclusive will not be paid for, if working on new works item.) opening (mm)
Each
N.e. 150 - addit-
150 300 ional
100
A B C
Each $ $ $
08187 Bore or cut round hole through any type of boarding or sheeting in any thickness................................................................................... 1.00 2.90 2.00 08187
08188 Cut square or rectangular hole through any type of boarding or sheeting in any thickness...................................................................... 2.00 4.00 2.90 08188
GLASS FIBRE INSULATION
Uncompressed thickness (mm)
12 25 50
A B C
Per square metre $ $ $
08189 Glass fibre mat in rolls laid butt jointed on slab......................................................................................................................................... - 14.90 21.20 08189
08190 Ditto but fixed to timber floor joists, timber wall battening or partitions, or soffits of ceiling joists or
bearers, with clout headed nails or fixing fillets (measured separately).................................................................................................... - 18.50 25.20 08190
08191 Extra over glass fibre mat for faced on one side with aluminium foil....................................................................................................... - 17.50 18.20 08191
08192 Glass fibre resin bonded slabs laid butt jointed on slab under screed (measured separately)................................................................... 26.10 39.90 60.00 08192
08193 Ditto but fixed with approved adhesive to slabs, face of walls, ducts, etc................................................................................................ 40.10 54.00 73.50 08193
08194 Extra over glass fibre resin bonded slab for faced on one side with aluminium foil................................................................................. 16.80 16.80 16.80 08194
FIRE RESISTING INSULATION BOARD
Fire resisting insulation board fixed to position (horizontally or vertically) in any form : - 45 kg/m 60 kg/m 80 kg/m 100 kg/m 125 kg/m
A B C D E
Per square metre $ $ $ $ $
08195 30 mm thick............................................................................................................................................................. 29.80 34.40 38.30 39.30 45.60 08195
08196 50 mm thick............................................................................................................................................................. 61.80 69.00 75.30 82.90 94.20 08196
08197 75 mm thick............................................................................................................................................................. 105.20 115.10 123.50 134.80 151.60 08197
08198 100 mm thick........................................................................................................................................................... 145.40 159.00 170.10 184.40 206.00 08198
08/27
08 CARPENTRY AND JOINERY 08
Item Item
REPAIRS TO BUILDING BOARDS AND SUNDRY ITEMS
Take Take
down down Fix
and and set only
clear aside for
away re-use
A B C
Per square metre $ $ $
08199 Detached solid or slat shelving complete with bearers and wood or steel brackets (top
surface area of shelving measured)............................................................................................................................................................. 16.00 16.60 50.20 08199
08200 Plywood of any type or thickness, and in any position............................................................................................................................... 12.10 12.80 48.90 08200
08201 Plasterboard ditto........................................................................................................................................................................................ 12.10 12.80 49.00 08201
08202 Fibre or fire resisting insulating board ditto............................................................................................................................................... 10.20 10.90 40.50 08202
08203 Blockboard ditto.......................................................................................................................................................................................... 12.10 12.80 48.50 08203
08204 Wood chipboard ditto.................................................................................................................................................................................. 12.10 14.70 48.50 08204
08205 Laminated plastic decorative sheeting ditto............................................................................................................................................... 10.20 12.10 54.80 08205
08206 Flat fibrous reinforced cement sheeting ditto............................................................................................................................................. 10.90 12.10 64.20 08206
08207 Glazed fibrous reinforced cement sheets ditto........................................................................................................................................... 10.90 12.10 59.20 08207
08208 Wood wool slabs of any thickness fixed to any position............................................................................................................................ 12.80 14.70 26.80 08208
08209 Baize or fine felt fixed to any boarding in any position............................................................................................................................. 6.40 7.00 35.40 08209
08210 Glass fibre insulation of any type and thickness laid on or fixed to any component................................................................................. 5.70 6.40 6.60 08210
08211 Notice and directory boards, pin board and the like fixed to or hung on wall or column......................................................................... 17.90 18.50 55.50 08211
08/28
08 CARPENTRY AND JOINERY 08
Item Item
PROPRIETARY SPORT HALL FLOORING SYSTEMS Take
Supply down
and and
fix clear
away
A B
Per square metre $ $
08212 Proprietary sports flooring with 174 x 57 x 10 mm nominal thickness timber blocks on a consolidated yard broom
finished concrete levelled subfloor, total thickness of cement sand fixing bed and timber flooring blocks to be 20 mm,
grout all joint with mid-grey compound from the same manufacturer, machine sand the whole floor and apply
polyurethane seal from the same manufacturer............................................................................................................................................................ 856.90 7.00 08212
08213 Proprietary cushioned sleeper sports floor system enhanced with 12 mm exterior grade plywood subfloor, on 50 x 75 mm
sleepers spruce at 300 mm centres, pine or fir, CCA pressure treated, cushion pad by the same manufacturer for increased
shock absorption and added resiliency, finished with hard maple flooring 19 x 57 mm, tongue and groove joints, supplied
by the same manufacturer, 6 mm polyethylene vapour barrier (measured separately), to DIN 18032 Part 2, including
machine sanding and applying wood preservative on wood before fixing all as recommended by the manufacturer............................................... 1,019.30 8.30 08213
08214 Ditto but including applying three coats of polyurethane paint .................................................................................................................................. 1,172.20 8.30 08214
08215 Proprietary two-layer plywood subfloor sports floor system with 2 layers of 12 mm exterior grade plywood nailed
together, low profile system for blending with existing floor levels, fixed on 10 mm thick ISO cushion pad by the same
manufacturer, finished with hard maple flooring 19 x 57 mm, tongue and groove joints, supplied by the same
manufacturer, 6 mm polyethylene vapour barrier (measured separately), to DIN 18032 Part 2, and include machine
sanding and applying three coats of polyurethane paint and any necessary wood preservative on wood before
fixing all as recommended by the manufacturer........................................................................................................................................................... 1,263.90 8.30 08215
08216 Proprietary sports flooring system with first grade maple strip flooring of 19 x 57 mm, random length on two layers of
12 mm exterior grade plywood crossed and tacked with 19 mm thick pneumatic conical natural rubber pads at 300 mm
centres affixed to the bottom, laid on 6 mm thick polyethylene sheet vapour barrier (measured separately) and
include machine sanding and applying three coats of polyurethane paint and any necessary wood preservative on
wood before fixing all as recommended by the manufacturer..................................................................................................................................... 1,256.20 8.30 08216
08217 Proprietary sports flooring system with 22 x 129 x 1830 / 3700 mm (L) solid beech floor board, to DIN 18032 Part 2,
floor board weight 16.2 kg/m2, tongue and groove joints, controlled equilibrium moisture content 8% (+/-2%) and factory
finished with 2 coats of Iso-lacquer, fully sprung batten system with single layer battens from the same manufacturer
including resilient rubber strips with integrated progressive shock absorption, 32 kg/m3 sound absorption fiberglass
blanket laid between battens, together with 0.20 mm PE-foil moisture barrier laid on sub-floor all as recommended by
the manufacturer............................................................................................................................................................................................................ 1,361.20 8.30 08217
08218 Proprietary sports flooring system with 22 x 129 x 1830 / 3700 mm(L) solid beech floor board, to DIN 18032 Part 2,
floor board weight 16.2 kg/m2, tongue and groove joints, controlled equilibrium moisture content 8% (+/-2%) and factory
finished with 2 coats of Iso-lacquer held together by clips by the same manufacturer on the underside, supported by
an intermediate layer of 5 or 10 mm resilient foam of extruded polyethylene cellular plastic, together with 0.20 mm
PE-foil moisture barrier laid on sub-floor all as recommended by the manufacturer.................................................................................................. 1,138.40 8.30 08218
Supply
and
fix
A
Per linear metre $
08219 100 x 75 x 10 mm Thick 'L' shape vent cove rubber wall base skirting........................................................................................................................................ 187.90 08219
08220 12 x 100 mm Maple wood skirting with two coats of polyurethane paint.................................................................................................................................... 69.10 08220
08/29
08 CARPENTRY AND JOINERY 08
Item Item
GLUE - LAMINATED TIMBER
Glue - laminated timber shall be manufactured from plantation grown Radiata Pine, CCA (Copper Chromium Arsenate) treated
to Hazard Class as described in accordance with NZMP 3640 (1988). Glue laminated timber shall comply with NZS3603,
NZS3606 and NZS3616. All glue shall be Resorcinol or Phenol, Resorcinol used to manufacturer's instructions. Moisture
content at the time of lamination shall be 12-16% : -
A
Per linear metre $
08221 90 x 65 mm...................................................................................................................................................................................................................................... 154.10 08221
08222 135 x 65 mm.................................................................................................................................................................................................................................... 221.30 08222
08223 180 x 65 mm.................................................................................................................................................................................................................................... 288.70 08223
08224 230 x 65 mm.................................................................................................................................................................................................................................... 362.40 08224
08225 180 x 90 mm.................................................................................................................................................................................................................................... 390.70 08225
08226 230 x 90 mm.................................................................................................................................................................................................................................... 485.90 08226
08227 280 x 90 mm.................................................................................................................................................................................................................................... 569.10 08227
08228 230 x 113 mm.................................................................................................................................................................................................................................. 641.80 08228
08229 280 x 113 mm.................................................................................................................................................................................................................................. 769.60 08229
Add to either of Items 08221 to 08229 inclusive for members cut curved from solid timber including dowelling and keying sections................................... 20%
Ditto for members bent to curve to radius n.e. 15.00 m during fixing by means of saw cuts, steaming bending, etc................................................................. 20%
Ditto for members cut rounded or mopstick from solid timber including dowelling and keying sections................................................................................... 35%
A
Per linear metre $
08230 Take down and clear away glue laminated timber in any size....................................................................................................................................................... 4.50 08230
08231 Take down and set aside for re-use ditto........................................................................................................................................................................................ 5.10 08231
08232 Fix only ditto................................................................................................................................................................................................................................... 48.10 08232
08/30
08 CARPENTRY AND JOINERY 08
Item Item
LANDSCAPE TIMBER Structural Structural No. 2 No. 2
Select Select Framing Framing
Grade Grade Grade Grade
CCA - H3 CCA - H4 CCA - H3 CCA - H4
A B C D
Per cubic metre $ $ $ $
08233 Wrot landscape timber scantling n.e. 0.02 m sectional area................................................................................................... 19,423.70 25,222.90 16,765.20 17,735.10 08233
08234 Ditto exceeding 0.02 m sectional area..................................................................................................................................... 13,648.80 14,439.80 11,773.70 12,488.30 08234
Add to either of Items 08233 to 08234 inclusive for members cut curved from solid timber dowelling and keying sections.................................................... 20%
Ditto for members bent to curve to radius n.e. 15.00 m during fixing by means of saw cutting, steaming bending, etc............................................................ 20%
Ditto for members cut rounded or mopstick from solid timber including dowelling and keying sections................................................................................... 35%
Sectional area (m)
n.e. 0.02 exc. 0.02
A B
Per cubic metre $ $
08235 Take down and clear away landscape timber in any size............................................................................................................................................. 218.80 185.00 08235
08236 Take down and set aside for re-use ditto...................................................................................................................................................................... 368.00 305.50 08236
08237 Fix only ditto................................................................................................................................................................................................................. 1,271.80 1,059.00 08237
RECYCLED PLASTIC LUMBER Square / rectangular
sectional area (m)
Recycled plastic lumber, resistant to UV, vandal, impact, algae, moss and corrosion; and rot, splinter and crack proof :- n.e. 0.02 exc. 0.02
A B
Per cubic metre $ $
08238 Recycled plastic lumber (if the total quantity measured in a single Works Order exceed 0.05 m)........................................................................... 17,876.00 18,881.30 08238
Per linear metre
08239 Recycled plastic lumber (if the total quantity measured in a single Works Order n.e. 0.05 m)................................................................................. 178.80 377.60 08239
Add to either of Items 08238 to 08239 inclusive for recycled plastic lumber of specific quality................................................................................................ 50%
Square / rectangular
sectional area (m)
n.e. 0.02 exc. 0.02
A B
Per cubic metre $ $
08240 Take down and clear away recycled plastic lumber in any size................................................................................................................................... 218.80 185.00 08240
08241 Take down and set aside for re-use ditto...................................................................................................................................................................... 368.00 305.50 08241
08242 Fix only ditto including making all joints..................................................................................................................................................................... 1,271.80 1,059.00 08242
08/31
08 CARPENTRY AND JOINERY 08
Item Item
PROPRIETARY SOLID SURFACING MATERIALS
Counter top of proprietary solid surfacing material; non-porous surfacing material homogeneously composed of +1/3
acrylic resin (also known as PolyMehtyl MethAcrylate or PMMA), and + 2/3 natural minerals composed of Aluminum
TriHydrate (ATH) derived from bauxite, an ore from which aluminum is extracted; (Elongation : DIN 53 445 (ISO/DIS 527-78 Supply
0.36-0.49%) : - and
fix
A
Per square metre $
08243 12.3 mm Thick counter top............................................................................................................................................................................................................. 2,843.00 08243
Per linear metre
08244 Extra over Item 08243 for bull nose n.e. 50 mm wide................................................................................................................................................................... 104.30 08244
08245 Ditto for backsplash n.e. 50 mm high............................................................................................................................................................................................. 193.10 08245
08246 Ditto for backsplash 50 to 100 mm high ....................................................................................................................................................................................... 369.50 08246
08247 Ditto for front apron n.e. 100 mm high......................................................................................................................................................................................... 192.30 08247
08248 Ditto for front apron 100 to 200 mm high...................................................................................................................................................................................... 378.50 08248
08249 Ditto for front apron 200 to 300 mm high...................................................................................................................................................................................... 557.20 08249
08250 Ditto for inlay n.e. 20 mm wide...................................................................................................................................................................................................... 304.80 08250
Each
08251 Extra over Item 08243 for integral single bowl sink; external size : 469 mm (L) x 382 mm (W) x 183 mm (D);
internal size : 418 mm (L) x 331 mm (W) x 134 mm (D).............................................................................................................................................................. 1,393.20 08251
08252 Ditto for integral single bowl sink; external size : 445 mm (L) x 445 mm (W) x 223 mm (D); internal size :
401 mm (L) x 401 mm (W) x 206 mm (D)..................................................................................................................................................................................... 1,892.90 08252
08253 Ditto for integral single bowl sink; external size : 583 mm (L) x 450 mm (W) x 201 mm (D); internal size :
533 mm (L) x 400 mm (W) x 187 mm (D)..................................................................................................................................................................................... 2,541.80 08253
08/32
08 CARPENTRY AND JOINERY 08
Item Item
PROPRIETARY SOLID SURFACING MATERIALS (CONT'D)
Counter top of proprietary solid surfacing material, a homogeneous thermoset polymer alloy, comprised of both acrylic
and polyester co-polymer components and filled with Aluminum TriHydrate (ATH) under the license of the diller corporation
with hardness Rockwell M95 at ASTM test D785 and barcol 61 at ASTM test 2583; and complies with NSF-51, NEMA LD-3, Supply
ASTM tested : - and
fix
A
Per square metre $
08254 12.7 mm Thick counter top............................................................................................................................................................................................................. 2,573.80 08254
Per linear metre
08255 Extra over Item 08254 for bull nose n.e. 50 mm wide................................................................................................................................................................... 95.90 08255
08256 Ditto for backsplash n.e. 50 mm high............................................................................................................................................................................................. 185.50 08256
08257 Ditto for backsplash 50 to 100 mm high ....................................................................................................................................................................................... 365.60 08257
08258 Ditto for front apron n.e. 100 mm high......................................................................................................................................................................................... 189.90 08258
08259 Ditto for front apron 100 to 200 mm high...................................................................................................................................................................................... 365.50 08259
08260 Ditto for front apron 200 to 300 mm high...................................................................................................................................................................................... 552.70 08260
Each
08261 Extra over Item 08254 for integral single bowl basin; oval shape; overall internal size : 432 mm x 346 mm x 146 mm deep.................................................. 1,163.90 08261
08262 Ditto for integral single bowl basin; oval shape with one straight side; overall internal size : 381 mm x 267 mm x 146 mm deep........................................... 1,359.00 08262
08263 Ditto for integral single bowl basin; oval shape; overall internal size : 543 mm x 346 mm x 146 mm deep............................................................................... 2,039.50 08263
08264 Ditto for integral single sink; rectangular shape; internal size : 406 mm x 406 mm x 210 mm deep.......................................................................................... 1,169.60 08264
08265 Ditto for integral double sinks; rectangular shape; overall internal size : 838 (381 & 381) mm x 406 mm x 210 mm deep...................................................... 2,641.60 08265
08266 Ditto for integral double sinks; rectangular shape; overall internal size : 787 (483 & 279) mm x 406 mm x 210 mm deep...................................................... 2,641.60 08266
Proprietary solid surfacing material fixed to wall of various colour range and finish including curved corner, round edge, fixing
bracket, accessories, cut holes, pointing, jointing and sealing edges with sealant, etc. : -
Per square metre
08267 12.7 mm Thick proprietary solid surfacing material fixed to wall of non-porous surfacing material, acrylic-modified based
(ISSFA recommended), acrylic modified blinder (ISO-NPG type resin), Aluminum Hydroxide filler, non-toxic pigment, patented
additives; and providing maximum protection to all hygiene areas by Nano Sliver Anti-bacterial Technology......................................................................... 2,361.90 08267
08268 12.3 mm Thick proprietary solid surfacing material fixed to wall of non-porous surfacing material homogeneously composed of +1/3
acrylic resin (also known as PolyMehtyl MethAcrylate or PMMA), and + 2/3 natural minerals composed of Aluminum TriHydrate
(ATH) derived from bauxite, an ore from which aluminum is extracted. (Elongation : DIN 53 445 (ISO/DIS 527-78) 0.36-0.49%)....................................... 2,952.10 08268
08269 12.7 mm Thick proprietary solid surfacing material fixed to wall, a homogeneous thermoset polymer alloy, comprised of both acrylic and
polyester co-polymer components and filled with Alumina Trihydrate (ATH) under the license of the diller corporation with hardness
Rockwell M95 at ASTM test D785 and barcol 61 at ASTM test 2583; and complies with NSF-51, NEMA LD-3, ASTM test................................................ 2,891.20 08269
08/33
08 CARPENTRY AND JOINERY 08
Item Item
PROPRIETARY ANTI-RICOCHET SURFACES
Proprietary anti-ricochet tiles for flooring, walling and ceiling, size of 1000 mm x 500 mm (+/- 1%),
thickness at 43 mm, weight approximately 35 kg/m2; can be fixed or loose laid, with 2-component
polyurethane adhesive or with stainless steel screws to ceiling; tensile strength of approximately
1/mm2 and the elongation at break is approximately 75% according to DIN 53 571; tear resistance
at approximately 11 N/mm according to DIN 53 515 Graves; with heat resistance is up to 80, shortly Take Take
up to 100; water permeability at 0.34 cm/s that comply with the standard of DIN 18 035 Part 6; Supply down down
Fix
stress at 20% compression at approximately 0.74 N/mm2 according to DIN 53 577; can meet the and and and set
only
fire resistance standard according to DIN 4102 Class B2; certified with the standard DIN EN ISO fix clear aside for
9001:2000 and ISO 14001:2004 : - away re-use
A B C D
Per square metre $ $ $ $
08270 Proprietary anti-ricochet tile...................................................................................................................................................... 1,289.30 12.80 46.60 84.20 08270
Each
08271 Proprietary anti-ricochet tile, total area not exceeding 0.50 m of each Works Order............................................................. 694.90 6.40 23.60 42.10 08271
08/34
Section 09
IRONMONGERY
09 IRONMONGERY 09
SECTION 09
IRONMONGERY
SPECIAL CONDITIONS
Specification SC09.01 This Section shall generally be read and used in conjunction with the Specification adopted
in the Contract.
Measurement SC09.02 The "supply and fix" and "fix only" of various items of ironmongery shall be measured as
of "supply follows : -
and fix" and
"fix only" of (a) Butt, rising or falling butt, backflap,
ironmongery counter or Parliament hinge - Length along joint
(b) Cross garnet, tee or hook and ride hinge - Length from joint or
knuckle to point
(c) Spring hinge - Length along spring
(d) Tower or barrel bolt - Length of shoot
(e) Monkey tail bolt - Length overall
(f) Flush bolt and lever flush bolt - Length of plate
(g) Casement stay - Length from hinge to point
(h) Cabin hook - Length of hook
(i) Hasp and staple - Length from hinge to point
(j) Sliding door gear track and
channel, curtain track
and valance rail - Net length fixed
09/1
09 IRONMONGERY 09
SPECIAL CONDITIONS
Measurement SC09.03 Measurement of labour for taking down and clearing away or setting aside for re-use of
of labour for ironmongery shall be based on the following classification : -
ironmongery
(a) Group I : Articles of ironmongery or related fittings generally which involve only
minor labour, including but not be limited to the following
- Hinges generally
- Bolts generally except for panic bolts
- Door furniture generally
- Door seals generally
- Door holders and stoppers
- Fittings for sashes and fanlights
- Fittings for sliding sashes
- Fittings for jalousies and typhoon bars
- Fittings for doors and cupboards generally
- Similar articles or fittings
(b) Group II : Articles of ironmongery or related fittings generally which involve more
labour when compared with Group I, including but not be limited to the following
- Activating bar of panic bolts or panic exit devices (emergency panic bolt and
alarm system and rim exit device and alarm system are measured separately)
- Key-in the knob type of lock and latch sets
- Locks and latches generally
- Digital lock sets
- Door closers generally
- Sliding door gear
- Similar articles or fittings
(c) Group III : Articles of ironmongery or related fittings generally which involve more
extensive labour when compared with Groups I and II, including but not be
limited to the following
- Floor springs, both concealed and exposed types
- Similar articles or fittings
Labour for taking down and clearing away of ironmongery shall not be measured
separately where the same is taken down together with the removal of doors, windows
and/or frames.
SC09.04 Unless otherwise stated herein, all articles of ironmongery shall be measured per unit of
article of ironmongery irrespective of sizes and materials, except for the following : -
(a) Door seals shall be measured based on each number of single door.
(b) Curtain tracks shall be measured based on each number of window.
(c) Tracks and/or channel guides related to the sliding door gear shall be measured
together and measured once only based on each number of sliding door, and are
inclusive of brackets and accessories.
09/2
09 IRONMONGERY 09
SPECIAL CONDITIONS
Measurement SC09.05 Repairs to ironmongery shall be measured based on the same classification as described in
of repairs to Clause SC09.03 herein.
ironmongery
No measurement for oiling, easing, adjusting and re-securing of ironmongery shall be made
if repairs of ironmongery are measured as a separate item.
Measurement SC09.06 Circular or irregular shaped signs shall be measured as the smallest square or rectangle
of signage from which the sign can be cut.
generally
Cutting plastic sign shall be measured as a single cut and is only applicable to cutting
shapes, features and the like other than for letters and characters.
Cutting out letters, numbers or Chinese characters shall include for all full stops and
commas. No separate payment shall be made. All punctuations other than full stops and
commas shall be treated as letters. Logos, graphics and the like shall be measured as
Chinese characters of the same size.
Finishes to SC09.07 Unless otherwise stated, the material for articles of ironmongery is classified into the
ironmongery following types : -
Type A : aluminium, stainless steel or brass
Type B : steel, galvanized steel and wrot iron
The rates for Type A materials shall further include for any of the following surface finishes
as required : -
(a) Electroplated coatings on nickel, chromium, bronze, brass, cadmium or zinc to
form satin, bright, polished or similar plated finishes.
(b) Anodic oxidation coating on aluminium to form milled finish, rough or soft texture
finish, polished, satin anodized or similar finish.
(c) Coating on stainless steel to form polished or satin finish.
(d) Protection of all concealed components by the manufacturer's standard finish.
The rates for Type B materials shall further include for protection by galvanizing, zinc or
cadmium plated finish.
Rates for SC09.08 The rates for ironmongery shall generally include for : -
ironmongery
generally (a) Submission of samples, catalogues and certificates, and obtaining approval from
the Maintenance Surveyor as required.
(b) Provision of ironmongery schedule as G.S. Item 14.09.
09/3
09 IRONMONGERY 09
SPECIAL CONDITIONS
Rates for SC09.08 (c) Provision of key-alike or master-keying, if required, except for key-alike or
ironmongery (Cont'd) master-keying to existing group of door locks.
generally
(Cont'd) (d) Fixing to any type of timber or building board or other surfaces.
(e) Provision of all necessary screws to match the ironmongery and all bolts, nuts,
washers, nails, pins and the like.
(f) Protecting with approved intumescent sheets or intumescent paint where
required.
(g) All housing, sinking, drilling and similar labours required to timber or other surface
to which the article is being fixed.
(h) All plugging in concrete, brick, stone or other floors, walls, columns, soffits and
the like.
(i) Cutting and grouting all mortices, pockets, etc., for bolts, bolt sockets, floor spring
boxes and the like.
(j) Oiling, easing and adjusting, and leaving the ironmongery in perfect working order.
(k) Making good disturbed surfaces.
Rates for SC09.09 The rates for bolts shall further include for : -
bolts
(a) All sockets, staples plates, thimbles, etc. and all necessary accessories.
(b) Square or circular, straight or necked shoot.
Rates for SC09.10 The rates for locks shall further include for : -
locks
(a) Provision of knob with or without rose, lever handles with cover plates, and the
like.
(b) Provision of key hole escutcheon.
(c) Provision of keys and identification discs.
(d) Stamping number on lock face.
Rates for SC09.11 The rates for taking down and clearing away or setting aside for re-use of ironmongery,
labour for shall include for : -
ironmongery
(a) Piecing out and filling all old housing, sinking, screw holes, mortices and the like.
(b) Finishing surface fair and spot painting, polishing or making good.
09/4
09 IRONMONGERY 09
SPECIAL CONDITIONS
Rates for SC09.12 The rates for repairs to ironmongery shall include for : -
repairs to
ironmongery (a) Replacement of any compatible parts, fittings and fixing accessories, if required.
(b) Provision of any ancillary works as may be necessary.
(c) Carrying out oiling, easing, adjusting and re-securing of ironmongery on
completion of repairs and leaving the ironmongery in perfect working order.
Rates for SC09.13 The rates for plastic or metal signs, silkscreen printing and translucent film signage shall
plastic or generally include for : -
metal signs,
silkscreen (a) Setting out, cutting to size, bevelling and polishing edges, and anodizing after
printing and manufactured as required.
translucent
film signage (b) Drilling, plugging and screwing with brass, chromium plated or stainless steel
generally screws, or fixing with approved adhesive or fixing on a special suspension system
(measured separately).
(c) Providing backing plate with colour coating, powder coating, anodized or
polished finish on all exposed surfaces before silkscreen printing or after cut out
or cut through signage.
(d) Temporary protection with mask as required.
(e) Making good disturbed surfaces.
(f) Design, submission of shop drawings, samples and the like.
(g) Compliance with Design Manual : Barrier Free Access, issued by Buildings
Department, 2008 Edition.
Rates for SC09.14 The rates for silkscreen printing and translucent film signage to existing surfaces shall
silkscreen further include for : -
printing and
translucent (a) Preparing substrate surface to receive silkscreen printing or translucent
film signage film.
to existing
surfaces
Rates for SC09.15 The rates for plastic signs with cut through letters, Chinese characters and the like shall
plastic signs further include for : -
with cut
through (a) Cutting through for letters, numbers, Chinese characters, graphics, punctuations
letters, Chinese and the like.
characters
and the like (b) Plastic sign plate of any colour or finishes.
(c) Finishing with polished edges.
09/5
09 IRONMONGERY 09
SPECIAL CONDITIONS
Rates for SC09.16 The rates for letter or number signs cut from plastic or metal sheet shall further include for :-
letter or
number signs (a) Cutting out from sheets.
cut from
plastic or (b) In the case of plastic signs, any colour or finishes.
metal sheet
(c) Finishing with polished edges.
(d) Fixing with moulded metal/plastic pegs or projecting plastic.
(e) In the case of anodized aluminium signs, re-anodize after fabrication.
Rates for SC09.17 The rates for engraved plastic sign face shall further include for : -
engraved
plastic (a) Picking out with paint either in single or multi-colour for engraved letters, number,
sign face Chinese characters, graphics, punctuations and the like.
(b) Provision of plastic backing plate.
(c) Finishing with mirror face when engraved on the back of the plastic.
Rates for SC09.18 The rates for acid etched stainless steel sign face shall further include for : -
acid etched
stainless (a) Picking out with paint either in single or multi-colour for acid etched letters, number,
steel sign Chinese characters, graphics, punctuations and the like.
face
(b) Provision of stainless steel backing plate.
(c) Finishing with polished face.
Government SC09.19 Where ironmongery is obtained from Government stores or other designated suppliers, the
stores or rates for Fix only will be paid.
other
designated
suppliers
09/6
09 IRONMONGERY 09
Item Item
HINGES Supply and fix
Type Type Fix only
A B
A B C
Per pair $ $ $
09001 Butt hinges with or without nylon bushes n.e. 75 mm long....................................................................................................................... 37.70 28.30 11.70 09001
09002 Ditto 75 - 125 mm long............................................................................................................................................................................... 64.10 48.10 14.60 09002
09003 Rising or falling butt hinges n.e. 75 mm long............................................................................................................................................ 64.50 - 14.60 09003
09004 Ditto 75 - 100 mm long............................................................................................................................................................................... 67.10 - 17.60 09004
09005 Backflap hinges n.e. 75 mm long................................................................................................................................................................ 40.70 30.50 11.70 09005
09006 Counter hinges n.e. 75 mm long................................................................................................................................................................. 55.20 - 7.30 09006
09007 Parliament hinges n.e. 75 mm long............................................................................................................................................................. 87.70 - 17.60 09007
09008 Ditto 75 - 150 mm long............................................................................................................................................................................... 115.70 - 26.30 09008
09009 Cranked or semi-concealed cupboard hinges............................................................................................................................................. 84.20 63.20 8.80 09009
09010 Fully concealed cupboard hinges................................................................................................................................................................ 30.50 22.90 8.80 09010
09011 Cross garnet or tee hinges up to 150 mm long........................................................................................................................................... - 13.60 7.30 09011
09012 Ditto 150 - 300 mm long............................................................................................................................................................................. - 27.80 10.20 09012
09013 Ditto 300 - 450 mm long............................................................................................................................................................................. - 38.10 13.20 09013
09014 Ditto 450 - 600 mm long............................................................................................................................................................................. - 45.40 17.60 09014
09015 Hook and ride hinges, local made heavy pattern, with hook riveted to plate up to 300 mm long............................................................ 44.00 33.00 10.20 09015
09016 Ditto 300 - 600 mm long............................................................................................................................................................................. 62.80 47.10 14.60 09016
09017 Ditto 600 - 900 mm long............................................................................................................................................................................. 86.50 64.90 26.30 09017
09018 Add to either of Items 09015 to 09017 inclusive if hook plate is flanged for and cast into concrete,
brick or stone wall including cutting mortice and grouting....................................................................................................................... 7.30 7.30 7.30 09018
09019 Single action spring hinges n.e. 75 mm...................................................................................................................................................... 49.10 36.90 11.70 09019
09020 Ditto 75 - 150 mm long............................................................................................................................................................................... 68.10 51.10 14.60 09020
09021 Double action spring hinges n.e. 75 mm long............................................................................................................................................ 69.80 52.40 14.60 09021
09022 Ditto 75 - 150 mm long............................................................................................................................................................................... 106.60 80.00 14.60 09022
09023 Safety hinges n.e. 75 mm long.................................................................................................................................................................... - 32.50 7.30 09023
09024 Ditto 75 - 150 mm long............................................................................................................................................................................... - 45.80 10.20 09024
Per linear metre
09025 Piano hinge.................................................................................................................................................................................................. 39.00 - 14.60 09025
09/7
09 IRONMONGERY 09
Item Item
BOLTS Supply and fix
Type Type Fix only
A B
A B C
Each $ $ $
09026 Tower or barrel bolt n.e. 75 mm long......................................................................................................................................................... 31.80 23.90 5.90 09026
09027 Ditto 75 - 150 mm long............................................................................................................................................................................... 33.30 24.90 7.30 09027
09028 Ditto 150 - 225 mm long............................................................................................................................................................................. 36.70 27.50 8.80 09028
09029 Ditto 225 - 300 mm long............................................................................................................................................................................. 50.20 37.60 10.20 09029
09030 Ditto 300 - 450 mm long............................................................................................................................................................................. 58.80 44.10 11.70 09030
09031 Ditto 450 - 600 mm long............................................................................................................................................................................. 80.40 60.30 17.60 09031
09032 Ditto 600 - 750 mm long............................................................................................................................................................................. 100.40 75.30 21.90 09032
09033 Ditto 750 - 900 mm long............................................................................................................................................................................. 128.60 96.50 23.40 09033
09034 Ditto 900 - 1,050 mm long.......................................................................................................................................................................... 162.40 121.80 24.90 09034
09035 Ditto 1,050 - 1,200 mm long....................................................................................................................................................................... 188.20 141.10 26.30 09035
09036 Monkey tail bolt n.e. 500 mm long............................................................................................................................................................. 78.50 58.90 14.60 09036
09037 Ditto 500 - 1,200 mm long.......................................................................................................................................................................... 162.40 121.80 21.90 09037
09038 Flush bolt with sunk slide n.e. 75 mm long................................................................................................................................................ 51.00 - 17.60 09038
09039 Ditto 75 - 150 mm long............................................................................................................................................................................... 57.60 - 20.50 09039
09040 Ditto 150 - 300 mm long............................................................................................................................................................................. 93.60 - 26.30 09040
09041 Lever flush bolt n.e. 75 mm long................................................................................................................................................................ 59.70 - 21.90 09041
09042 Ditto 75 - 150 mm long............................................................................................................................................................................... 69.10 - 21.90 09042
09043 Ditto 150 - 300 mm long............................................................................................................................................................................. 112.10 - 26.30 09043
09044 Ditto 300 - 600 mm long............................................................................................................................................................................. 162.70 - 36.60 09044
09045 Indicating bolt.............................................................................................................................................................................................. 56.90 - 24.90 09045
09046 Mortise dead bolt with indicator and long lever turn for handicap............................................................................................................ 285.40 - 24.90 09046
09/8
09 IRONMONGERY 09
Item Item
BOLTS (CONT'D) Supply and fix
Type Type Fix only
A B
A B C
Each $ $ $
09047 Flat bolt plate for any size shoot................................................................................................................................................................. 12.60 - 7.30 09047
09048 Bolt socket of any size for surface fixing.................................................................................................................................................... 20.50 - 7.30 09048
09049 Bolt socket of any size for letting into and including cutting mortice in concrete,
brick, stone or similar surface and grouting in and making good.............................................................................................................. 22.00 - 10.20 09049
Per set
09050 Handicap indicator bolts with long lever operated, specially designed for use by the physically disabled and
visually impaired with range of colour available for contrast purpose...................................................................................................... 738.40 553.80 26.30 09050
09051 Toilet door lock enables one handed operation with flip-up locking/opening function for handicapped use, also with
outside level handle to operate latch bolt and inside level handle to operate both the latch and deadbolt ; featuring
outside colour indicator showing locked or unlocked condition ; outside override function in case of emergency,
and provided with option of right hand or left hand side installation to door........................................................................................... 847.20 635.40 26.30 09051
PANIC BOLTS Take Take
Supply and fix down down Fix
and and set only
Type Type clear aside for
A B away re-use
A B C D E
Each $ $ $ $ $
09052 Panic exit device with type A bar operation (push-bar) as BS EN 1125 comprising horizontal
activating bar and vertical shoots to suit single door.............................................................................................. 1,074.90 - 13.80 29.70 55.60 09052
09053 Ditto but to suit double leaf door............................................................................................................................ 1,820.90 - 21.30 44.60 84.80 09053
09054 Panic exit device with type B bar operation (touch-bar) as BS EN 1125 comprising
horizontal activating bar vertical shoots to suit single door................................................................................... 934.70 - 11.70 26.60 52.70 09054
09055 Ditto but to suit pair of doors.................................................................................................................................. 1,519.10 - 18.10 40.40 79.00 09055
09056 Add to either of Items 09054 to 09055 inclusive for cylinder locking device from outside................................. 603.90 - 9.60 19.10 41.00 09056
09057 Emergency panic bolt featuring with push bar, alarm system operated by 9-volt battery with back up
device at sound level approximately 100 dB piezo alarm ; tamper resistant housing, saw-resistant
deadbolt, corrosion-resistant alloy lock body, optional two-point locking device, can resist at least
2,000 lbs. outside pull force, signages available in different languages, different colour option,
ten year warranty, and complies with standard of U.L .Listed panic hardware exceeds all
Life Safety, ADA, California Title 19, ANSI/BHMA for all building codes....................................................... 2,404.50 1,803.40 40.40 91.40 175.50 09057
09058 Rim exit device for single doors or pairs of doors constructed of metal, wood or composite materials ;
non-handed ; with deadlocking latch bolt engages roller strike ; coupled with battery operated and
completely self-contained audible alarm with sounds continuously UL/cUL Listed :
FVSR/FVSR7Panic hardware GXHX/FXHX7Fire exit hardware.................................................................... 4,203.10 3,152.30 40.40 91.40 175.50 09058
09/9
09 IRONMONGERY 09
Item Item
LOCKS AND LATCHES Supply and fix
Type Type Fix only
A B
A B C
Each $ $ $
09059 Suffolk latch with 200 x 50 mm plate........................................................................................................................................................ - 73.90 21.90 09059
09060 Rim latch with case, staple and brass spring bolt....................................................................................................................................... 273.70 205.30 26.30 09060
09061 Upright mortice latch with brass spring bolt and striking plate................................................................................................................. 180.60 135.50 35.10 09061
09062 Horizontal ditto............................................................................................................................................................................................ 188.30 141.20 35.10 09062
09063 Latch including knob set in stainless steel.................................................................................................................................................. 64.00 - 26.30 09063
09064 Bathroom lock including knob set with push button on one side and emergency device on the other side............................................. 69.40 - 29.30 09064
09065 Lock including knob set with push button on one side and locking device on the other side.................................................................. 70.80 - 29.30 09065
09066 Combined latch and dead lock including knob set with thumb turn on one side and locking device on the other side.......................... 184.90 - 46.80 09066
09067 150 mm Rim dead lock with case, staple, brass bolt and three lever mechanism..................................................................................... 91.00 68.20 26.30 09067
09068 150 mm Rim lock with case, staple, brass dead and spring bolt and three lever mechanism................................................................... 91.00 68.20 26.30 09068
09069 Horizontal mortice dead lock with brass bolt, keeper and four lever mechanism..................................................................................... 145.70 109.30 41.00 09069
09070 Ditto but with rebated fore-end................................................................................................................................................................... 165.80 124.40 45.30 09070
09071 Upright mortice lock with brass dead and spring bolt, striking plate and four lever mechanism............................................................. 160.80 120.60 45.30 09071
09072 Ditto but with rebated fore-end................................................................................................................................................................... 237.20 177.90 58.50 09072
09073 Horizontal mortice lock with brass dead and spring bolt, striking plate and four lever mechanism........................................................ 160.80 120.60 45.30 09073
09074 Ditto but with rebated fore-end................................................................................................................................................................... 237.20 177.90 58.50 09074
09075 Cylinder rim night latch (reversible) with staple, brass bolt, cylinder, thumb slide, knob and three keys............................................... 176.50 132.30 43.90 09075
09076 Cylinder mortice night latch with brass bolt, cylinder, thumb turn and three keys................................................................................... 282.50 211.90 58.50 09076
09077 Flush cupboard, drawer or desk lock with four lever mechanism.............................................................................................................. - 38.00 23.40 09077
09078 Ditto but with four pin tumbler mechanism............................................................................................................................................... 47.90 35.90 23.40 09078
09079 Self locking flush cupboard, drawer or desk lock with brass spring bolt and four pin tumbler mechanism............................................ 52.10 39.10 23.40 09079
09080 50 mm Padlock with hardened steel shackle and four lever mechanism................................................................................................... 33.80 25.40 2.90 09080
09081 75 mm Ditto................................................................................................................................................................................................. 40.10 30.10 2.90 09081
09082 50 mm Padlock with hardened steel shackle and five pin tumbler mechanism........................................................................................ 38.80 - 2.90 09082
09083 75 mm Ditto................................................................................................................................................................................................. 61.60 - 2.90 09083
09/10
09 IRONMONGERY 09
Item Item
LOCKS AND LATCHES (CONT'D) Supply
and Fix only
fix
A B
Each $ $
09084 Mechanical digital lock................................................................................................................................................................................................. 882.80 51.20 09084
09085 Approved mechanical push button heavy-duty lock with heavy-duty cylindrical and mortise locksets ; optional mechanical
key override, passage allows access, lockout (privacy) to disable the lock and access by key override only ; and different
finish options ; and conform to ANSI specifications................................................................................................................................................... 1,700.30 52.70 09085
09086 Approved Grade 2 key-in-lever lockset with chassis constructed of heavy gauge steel and cast components, plated
to protect against rust and corrosion ; locksets shall be adjustable for different door thickness ; non-handed ; with
separate anti-rotation through bolts ; no exposed mounting screws ; in solid one piece ; cast levers without plastic
inserts ; independent operated lever ; inside and outside lever return springs ; vandal resistant lever and be free
wheeling in the locked condition ; stainless steel latch bolt ; optional and complies with certifications
of ASNI A156.2 Series 4000, Grade 2, UL 3 Hour Fire Rating.................................................................................................................................. 261.40 36.60 09086
DOOR FURNITURE
Supply and fix
Replacement parts only : - Type Type Fix only
A B
A B C
Each $ $ $
09087 Key hole escutcheon.................................................................................................................................................................................... 13.90 - 2.90 09087
09088 Ditto with cover........................................................................................................................................................................................... 16.60 - 2.90 09088
09089 Single knob with rose if required................................................................................................................................................................ 24.00 18.00 4.40 09089
09090 Single lever handle with cover plate if required......................................................................................................................................... 43.60 32.70 5.10 09090
09091 Set of knob furniture complete with roses or cover plates and spindle..................................................................................................... 28.40 21.30 8.80 09091
09092 Set of lever handles ditto............................................................................................................................................................................. 112.30 84.20 8.80 09092
DOOR SEALS Supply
and Fix only
fix
A B
Per linear metre $ $
09093 Aluminium door seal with neoprene inserts................................................................................................................................................................. 91.70 8.80 09093
09094 PVC door seal with neoprene inserts............................................................................................................................................................................ 83.40 8.80 09094
09/11
09 IRONMONGERY 09
Item Item
DOOR SPRINGS AND HOLDERS Supply and fix
Type Type Fix only
A B
A B C
Each $ $ $
09095 Single action floor spring and top pivot with or without check................................................................................................................. 877.90 - 87.80 09095
09096 Double action ditto...................................................................................................................................................................................... 1,017.30 - 87.80 09096
09097 Spring action type floor door holder with rubber door stop....................................................................................................................... 69.70 - 5.90 09097
09098 Door holder, clip pattern............................................................................................................................................................................. - 35.70 5.90 09098
09099 40 mm Diameter rubber door stop.............................................................................................................................................................. 6.60 4.90 2.90 09099
09100 40 mm Ditto but with plate fixing.............................................................................................................................................................. 5.10 3.80 2.90 09100
09101 Door stopper, dome shape with rubber buffer, chrome plated................................................................................................................... 14.60 - 5.90 09101
09102 Overhead door closer, light duty non-hold open........................................................................................................................................ 157.70 118.30 36.60 09102
09103 Overhead door closer, heavy duty non-hold open...................................................................................................................................... 205.10 153.80 36.60 09103
09104 Extra over either of Items 09102 to 09103 inclusive with delayed action................................................................................................. 68.40 51.30 - 09104
09105 Concealed door closer, light duty non-hold open....................................................................................................................................... 176.70 132.50 58.50 09105
09106 Concealed door closer, heavy duty non-hold open..................................................................................................................................... 231.70 173.80 58.50 09106
09107 Extra over either of Items 09105 to 09106 inclusive with delayed action................................................................................................. 78.60 59.00 - 09107
FITTINGS FOR SASHES AND FANLIGHTS, ETC. Supply and fix
Type Type Fix only
A B
A B C
Each $ $ $
09108 75 mm Cleat hook....................................................................................................................................................................................... 14.70 - 2.90 09108
09109 Spring catch with projecting ring and strike plate or staple....................................................................................................................... 40.30 - 7.30 09109
09110 Staple only for spring catch......................................................................................................................................................................... 18.90 - 2.90 09110
09111 15 mm Internal diameter screw eye............................................................................................................................................................ 9.40 - 2.90 09111
09112 Casement fastener with 115 mm handle and hook or mortice plate.......................................................................................................... 37.70 28.20 7.30 09112
09113 200 mm Casement stay with two stud pins................................................................................................................................................ 29.30 22.00 10.20 09113
09114 250 mm Ditto............................................................................................................................................................................................... 30.40 22.80 10.20 09114
09115 300 mm Ditto............................................................................................................................................................................................... 31.40 23.60 10.20 09115
09116 Single stud pins........................................................................................................................................................................................... 7.80 5.80 4.40 09116
09117 Sliding bar type casement stay n.e. 300 mm long...................................................................................................................................... 53.40 28.30 10.20 09117
09118 Ditto 300 - 600 mm long............................................................................................................................................................................. 71.00 53.20 16.10 09118
09119 Fanlight opener with 300 mm long rack and pinion, worm wheel, pulley and endless cord.................................................................... 175.50 - 14.60 09119
09120 Set of two sash pivots and sockets.............................................................................................................................................................. 81.60 - 19.00 09120
09/12
09 IRONMONGERY 09
Item Item
FITTINGS FOR SLIDING SASHES, ETC. (CONT'D) Supply and fix
Type Type Fix only
A B
A B C
Each $ $ $
09121 15 mm Diameter sash rollers with frame and face plate............................................................................................................................ 30.90 - 10.20 09121
09122 20 mm Diameter ditto................................................................................................................................................................................. 34.60 - 10.20 09122
09123 Sash axle pulley with brass face, galvanized steel frame and 40 mm diameter brass wheel.................................................................... 32.40 - 11.70 09123
09124 Ditto but with 50 mm diameter brass wheel............................................................................................................................................... 50.30 - 13.20 09124
09125 25 mm Internal diameter sash eye on plate................................................................................................................................................. 32.70 - 4.40 09125
09126 Sash hook pattern lift on 50 mm plate........................................................................................................................................................ 38.60 - 4.40 09126
09127 Sash flush pattern lift size 75 x 40 mm overall.......................................................................................................................................... 56.00 - 8.80 09127
09128 Iron sash weight with hook or plate for cord attachment weighing 1.50 kg including providing and fixing cord................................... - 50.20 13.20 09128
09129 Add for each additional 0.50 kg or part thereof in weight......................................................................................................................... - 13.20 2.90 09129
09130 Pair of spiral rods and tension spring sash balances for sash weighing n.e. 13 kg and height of run n.e. 2 m........................................ - 249.90 30.70 09130
09131 Ditto but for sash weighing 13 kg - 20 kg.................................................................................................................................................. - 284.00 33.60 09131
09132 Ditto but for sash weighing 20 kg - 27 kg.................................................................................................................................................. - 288.50 38.00 09132
WINDOW OPENERS Take Take
Supply down down Fix
Approved mechanical systems for the window remote control comprising all necessary and and and set only
fixing accessories all in accordance with the manufacturer's instructions : - fix clear aside for
away re-use
A B C D
Each $ $ $ $
09133 Window opener for 1 sash high level window......................................................................................................................... 980.60 10.60 13.80 14.60 09133
09134 Ditto but 2 sashes...................................................................................................................................................................... 1,452.10 19.10 27.60 32.20 09134
09135 Ditto but 3 sashes...................................................................................................................................................................... 1,833.40 30.80 41.40 48.30 09135
09136 Ditto but 4 sashes...................................................................................................................................................................... 2,257.90 41.40 55.20 62.90 09136
09137 Add to Item 09136 for each additional sash............................................................................................................................. 467.40 10.60 13.80 14.60 09137
Approved electrically operated systems for the window remote control comprising all necessary fixing
accessories all in accordance with the manufacturer's instructions and connection to nearest power
point by a registered electrical worker : -
Each
09138 Window opener for 1 sash high level window......................................................................................................................... 2,153.80 12.80 15.90 35.10 09138
09139 Ditto but 2 sashes...................................................................................................................................................................... 2,492.10 23.40 31.90 70.20 09139
09140 Ditto but 3 sashes...................................................................................................................................................................... 2,830.40 36.10 51.00 105.30 09140
09141 Ditto but 4 sashes...................................................................................................................................................................... 3,159.90 47.80 63.70 131.60 09141
09142 Add to Item 09141 for each additional sash............................................................................................................................. 528.10 12.80 15.90 35.10 09142
09/13
09 IRONMONGERY 09
Item Item
FITTINGS FOR JALOUSIES AND TYPHOON BARS Supply and fix
Type Type Fix only
A B
A B C
Each $ $ $
09143 Turn buckle comprising 150 x 25 x 5 mm plate flanged one end with 15 x 15 mm pin 75 mm long filed circular
for half the length and fitted with 75 x 25 x 5 mm turn buckle splayed one end and holed for 15 x 15 mm pin..................................... - 55.90 10.20 09143
09144 Bar clip 150 x 40 x 5 mm twice bent and three times holed for screws.................................................................................................... 80.10 60.10 5.90 09144
09145 Eye for movable louvre............................................................................................................................................................................... 14.10 10.60 2.90 09145
09146 8 mm Diameter butterfly headed thumb screw 150 mm long.................................................................................................................... 26.00 - 2.90 09146
09147 Ditto but 200 mm long................................................................................................................................................................................ 32.30 - 4.40 09147
09148 50 x 50 x 3 mm Plate holed for thumb screw and four fixing screws....................................................................................................... 26.00 - 5.90 09148
09149 Ditto with tapped shoulder to receive 8 mm diameter screw..................................................................................................................... 35.30 - 5.90 09149
FITTINGS FOR DOORS AND CUPBOARDS Supply and fix
Type Type Fix only
A B
A B C
Per square metre $ $ $
09150 1.60 mm Kicking plate with bevelled edges if required and holed for screws.......................................................................................... 892.00 - 77.50 09150
Per linear metre
09151 Corner guard................................................................................................................................................................................................ 284.90 213.70 43.90 09151
Each
09152 Local pattern "Magic Eye" observation eyehole fitting.............................................................................................................................. 47.00 - 5.90 09152
09153 Cupboard door pull knob............................................................................................................................................................................ 12.00 9.00 2.90 09153
09154 Ditto with 50 mm diameter back plate........................................................................................................................................................ 17.40 - 2.90 09154
09155 Bales catch with plate size 28 x 10 mm...................................................................................................................................................... 20.20 - 5.90 09155
09156 Ditto but plate size 40 x 15 mm.................................................................................................................................................................. 21.00 - 5.90 09156
09157 Ditto but plate size 50 x 20 mm.................................................................................................................................................................. 21.80 - 5.90 09157
09158 Magnetic door catch.................................................................................................................................................................................... 23.50 17.70 5.90 09158
09159 Drawer, wardrobe or cupboard pull handle 100 mm long......................................................................................................................... 32.20 24.20 7.30 09159
09160 Ditto but 150 mm long................................................................................................................................................................................ 37.60 28.20 7.30 09160
09161 Door pull handle 225 mm long................................................................................................................................................................... 33.00 - 8.80 09161
09162 Ditto but 300 mm long................................................................................................................................................................................ 40.80 - 8.80 09162
09/14
09 IRONMONGERY 09
Item Item
FITTINGS FOR DOORS AND CUPBOARDS (CONT'D) Supply and fix
Type Type Fix only
A B
A B C
Each $ $ $
09163 300 x 75 mm Finger plate........................................................................................................................................................................... 30.70 - 7.30 09163
09164 75 x 45 mm Flush pattern drop drawer handle........................................................................................................................................... 31.00 - 14.60 09164
09165 75 x 40 mm Flush pull handle.................................................................................................................................................................... 30.20 22.70 13.20 09165
09166 100 x 50 mm Ditto...................................................................................................................................................................................... 31.10 23.30 13.20 09166
09167 75 x 40 mm Card holder frame................................................................................................................................................................... 20.10 15.10 4.40 09167
09168 100 x 75 mm Ditto...................................................................................................................................................................................... 23.20 17.40 4.40 09168
09169 150 x 100 mm Ditto.................................................................................................................................................................................... 31.40 23.60 4.40 09169
09170 25 x 1.60 mm Hanging plate....................................................................................................................................................................... 34.90 - 2.90 09170
09171 40 x 1.60 mm Ditto..................................................................................................................................................................................... 38.90 - 2.90 09171
09172 50 x 1.60 mm Ditto..................................................................................................................................................................................... 42.80 - 2.90 09172
09173 50 mm Coat hook........................................................................................................................................................................................ 12.40 - 2.90 09173
09174 100 mm Hat and coat hook......................................................................................................................................................................... 18.00 - 2.90 09174
09175 75 mm Combined hook and rubber door stop............................................................................................................................................ 26.90 - 2.90 09175
09176 25 mm Cup hook......................................................................................................................................................................................... 7.80 - 2.90 09176
09177 50 mm Hook................................................................................................................................................................................................ 18.60 13.90 2.90 09177
09178 100 x 75 mm Shelf bracket......................................................................................................................................................................... - 13.70 8.80 09178
09179 150 x 125 mm Ditto.................................................................................................................................................................................... - 17.00 10.20 09179
09180 225 x 175 mm Ditto.................................................................................................................................................................................... - 20.20 11.70 09180
09181 300 x 250 mm Ditto.................................................................................................................................................................................... - 24.20 13.20 09181
09182 Cabin hook and eye n.e. 150 mm................................................................................................................................................................ 35.70 26.70 11.70 09182
09183 Ditto but 150 - 300 mm............................................................................................................................................................................... 55.00 41.50 19.00 09183
09184 150 mm Double hinged cabin hook and eye.............................................................................................................................................. - 30.50 13.20 09184
09185 Eye for cabin hook....................................................................................................................................................................................... 12.60 9.50 4.40 09185
09186 Hasp and staple n.e. 75 mm........................................................................................................................................................................ - 9.40 7.30 09186
09187 Ditto but exceeding 75 mm......................................................................................................................................................................... - 11.50 8.80 09187
09188 Solid drawn flat bar type hasp and staple n.e. 75 mm................................................................................................................................ 11.60 8.70 7.30 09188
09189 Ditto but exceeding 75 mm......................................................................................................................................................................... - 10.90 8.80 09189
09/15
09 IRONMONGERY 09
Item Item
FITTINGS FOR DOORS AND CUPBOARDS (CONT'D)
Supply and fix
Type Type Fix only
A B
A B C
Each $ $ $
09190 450 mm Hinged swing locking bar with pivot and plate, two hook plates and staple plate..................................................................... 82.20 - 26.30 09190
09191 600 mm Ditto............................................................................................................................................................................................... 97.50 - 33.60 09191
09192 900 mm Ditto............................................................................................................................................................................................... 116.40 - 36.60 09192
09193 Door chain complete with slider and 100 x 40 mm plate........................................................................................................................... 42.20 31.70 13.20 09193
09194 Ditto but with 150 x 40 mm plate............................................................................................................................................................... 49.50 37.10 13.20 09194
09195 Slide or upright single pulley (screw or frame and plate) with wheel n.e. 25 mm diameter..................................................................... 21.20 15.90 5.90 09195
09196 Ditto with wheel 25 - 50 mm diameter....................................................................................................................................................... 23.70 17.80 5.90 09196
09197 Slide or upright double pulley (screw or frame and plate) with wheel n.e. 25 mm diameter................................................................... 26.30 19.70 5.90 09197
09198 Ditto with wheel 25 - 50 mm diameter....................................................................................................................................................... 31.40 23.50 5.90 09198
09199 Ash tray in any size, surface mounted........................................................................................................................................................ 171.90 - 4.40 09199
09200 Litter bin, 250 x 250 x 350 mm high, surface mounted ............................................................................................................................ 550.70 - 14.60 09200
09201 Ditto, 400 x 400 x 550 mm high, surface mounted.................................................................................................................................... 1,215.40 - 17.60 09201
09202 Stud pin with socket for shelves................................................................................................................................................................. 8.50 6.40 2.90 09202
Per pair
09203 Set of drawer slider 300 mm long............................................................................................................................................................... 42.90 32.20 7.30 09203
09204 Add to Item 09203 for each additional 50 mm long or part thereof in length........................................................................................... 5.10 3.80 2.90 09204
FIBRE TRACK, SLIDERS, ETC., FOR SMALL CUPBOARD Supply and fix
AND GLASS SLIDING DOORS Type Type Fix only
A B
A B C
Per linear metre $ $ $
09205 "Grooving-in" type track including cutting groove..................................................................................................................................... 29.90 22.50 10.20 09205
09206 "T" shaped track for surface fixing............................................................................................................................................................. 30.20 22.60 7.30 09206
09207 Single channel including cutting groove if required.................................................................................................................................. 53.10 39.80 14.60 09207
09208 Double channel including ditto................................................................................................................................................................... 56.20 42.20 14.60 09208
09209 Triple channel including ditto..................................................................................................................................................................... 64.20 48.10 14.60 09209
Each
09210 Slider of various sizes................................................................................................................................................................................. 11.60 8.70 2.90 09210
09/16
09 IRONMONGERY 09
Item Item
SLIDING DOOR GEAR
Supply and fix
Sliding door gear as BS EN 1527 : - Type Type Fix only
A B
A B C
Per linear metre $ $ $
09211 Track and fixed in bracket (measured separately)...................................................................................................................................... 433.00 324.80 14.60 09211
09212 Add to Item 09211 for plugging and screwing direct to wall, beam, lintol and the like........................................................................... 33.20 24.90 21.90 09212
09213 Channel guide and fix in and including cutting or forming groove or mortice in concrete or paved floor, grouting
and making good; or in wood, wood block floor or edge of door and any necessary plugging................................................................ 234.30 175.70 42.40 09213
Each
09214 Closed or open end track bracket for face fixing or soffit fixing, screwed to wood or plugged and
screwed to wall, beam, lintol and the like.................................................................................................................................................. 203.70 152.80 33.60 09214
09215 Add to Item 09214 for fixing with 8 mm rawbolt including drilling hole in concrete, brick, stone or
other surface and make good....................................................................................................................................................................... 20.70 15.50 10.20 09215
09216 Ditto but with 12 mm rawbolt..................................................................................................................................................................... 28.30 21.20 13.20 09216
09217 Four wheel hanger and adjustable split sprons........................................................................................................................................... 198.00 148.50 23.40 09217
09218 Two wheel swivel hanger with nylon wheels concealed fixing................................................................................................................. 468.70 351.60 24.90 09218
09219 Four wheel swivel hanger with nylon wheels concealed fixing................................................................................................................. 285.40 214.00 24.90 09219
09220 Two wheel swivel end hanger face fixing.................................................................................................................................................. 257.70 193.30 24.90 09220
09221 Two wheel swivel intermediate hanger face fixing.................................................................................................................................... 330.50 247.90 32.20 09221
09222 Brass roller guide light duty........................................................................................................................................................................ 46.60 35.00 10.20 09222
09223 Ditto face fixed heavy duty......................................................................................................................................................................... 136.90 102.70 13.20 09223
09224 Flush fold guide........................................................................................................................................................................................... 74.30 55.70 16.10 09224
09225 Face fixed end fold guide............................................................................................................................................................................ 97.60 73.20 10.20 09225
09226 Face fixed intermediate fold guide.............................................................................................................................................................. 148.50 111.40 17.60 09226
09/17
09 IRONMONGERY 09
Item Item
CURTAIN TRACKS Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per linear metre $ $ $ $
09227 Metal curtain track including rails, brackets, hoods and accessories, operated manually or by cord..................................... 51.20 2.10 4.30 7.30 09227
09228 Metal valance rail including brackets at not more than 400 mm centres and thirteen hooks per linear metre ...................... 30.00 1.60 3.20 5.90 09228
09229 Approved hospital curtain tracks including ditto..................................................................................................................... 384.10 3.20 5.30 43.90 09229
Replacement parts only : -
Each
09230 Bracket to metal curtain track................................................................................................................................................... 13.00 1.10 2.10 2.90 09230
09231 Double bracket at overlap to ditto............................................................................................................................................. 16.20 1.10 2.10 4.40 09231
09232 End stop to ditto........................................................................................................................................................................ 3.90 1.10 1.10 2.90 09232
09233 Runner to ditto including removing and replacing end stop as necessary............................................................................... 6.60 1.10 2.10 4.40 09233
09234 Bracket to metal valance rail..................................................................................................................................................... 13.00 1.10 2.10 2.90 09234
09235 Hook to ditto.............................................................................................................................................................................. 4.00 1.10 1.10 2.90 09235
Per linear metre
09236 Cord operated metal curtain track with regular duty rail in baked enamelled finish for ceiling and wall
mounting, one-way or two-way or multiple draw; the whole can withstand maximum fabric weight
of at least 16 pounds for one-way draw, or at least 30 pounds for two-way draw; including all
necessary brackets for top or face fixing, centre overlap and master slides, sliders and accessories
(pulley set measured separately)............................................................................................................................................... 54.10 2.10 4.30 8.80 09236
09237 Cord operated metal curtain track with double duty rail in baked enamelled finish for ceiling, wall and
recessed mounting, extra strong and rugged deluxe traverse line and flange construction, one-way or
two-way or multiple draw; the whole can withstand maximum fabric weight of at least 30 pounds
for one-way draw, or at least 45 pounds for two-way and multiple draw; including all necessary brackets
for top or face fixing, featuring with push-in style brackets for fast mounting, centre self-lubricating
overlap and master slides, concealed cord, sliders and accessories (pulley set measured separately).................................... 56.50 1.80 3.60 8.80 09237
Replacement parts only : -
Each
09238 Pulley set complete with cords to regular or double duty rail.................................................................................................. 15.80 1.10 2.10 4.40 09238
09239 Bracket to regular or double duty rail....................................................................................................................................... 5.20 1.10 2.10 2.90 09239
09240 Slider for regular or double duty rail......................................................................................................................................... 4.10 1.10 1.10 2.90 09240
09241 Master slide to regular or double duty rail................................................................................................................................ 4.40 1.10 1.10 2.90 09241
09242 Tension pulley........................................................................................................................................................................... 23.70 1.10 2.10 4.40 09242
09/18
09 IRONMONGERY 09
Item Item
MOSQUITOES/FLY SCREENS Take Take
Supply down down Fix
and and and set only
Mosquitoes or fly screens of approved gauge and mesh size in any colour coating or finish : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
09243 Plastic coated glass fibre mosquitoes or fly screens fixed to wood or metal frames with or without
beads (beads measured separately)........................................................................................................................................... 75.90 4.30 8.50 17.60 09243
09244 Brass mosquitoes or fly screens ditto........................................................................................................................................ 170.70 4.30 8.50 17.60 09244
09245 Aluminium mosquitoes or fly screens ditto.............................................................................................................................. 156.80 4.30 8.50 17.60 09245
09246 Stainless steel mosquitoes or fly screens ditto.......................................................................................................................... 296.00 4.30 8.50 17.60 09246
(Note : - The above Item 09246A will only be paid for, if ordered by the Maintenance
Surveyor in writing.)
ROLLER TYPE MOSQUITOES/FLY SCREENS Take Take
Supply down down Fix
and and and set only
Roller type mosquitoes or fly screens of approved gauge and mesh size in any colour coating or finish : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
09247 Aluminium vertical sliding roller retractable fly screen comprising a roller cassette and side channels
with aluminium pull down bar on heavy duty fiberglass fly screen mesh including catch and all
necessary ironmongery.............................................................................................................................................................. 532.30 4.30 8.50 17.60 09247
09248 Ditto but horizontal sliding roller type...................................................................................................................................... 527.80 3.60 7.20 17.60 09248
SUNDRIES Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per linear metre $ $ $ $
09249 12.70 mm Wide x 6.40 mm thick plastic foam self-adhesive draught excluder strip fixed to door
edge, window edge or similar position..................................................................................................................................... 6.20 1.10 - 4.40 09249
09250 Plastic foam self adhesive strip size 15 x 3 mm fixed to window or door edge...................................................................... 17.10 1.10 - 4.40 09250
09251 Vinyl plastic handrail capping to 50 mm core rail................................................................................................................... 37.80 4.30 9.60 17.60 09251
09252 Rubber speed reduction ramp including end caps and anchor bolts........................................................................................ 632.40 12.80 21.30 41.00 09252
Per set
09253 Approved ball bearing slides n.e. 500 mm long inset/horizontal type and soft closing mechanism flipper
to cupboard door complete with slides, pivoted arms and all necessary fittings and furniture............................................... 491.00 18.10 28.70 58.50 09253
09/19
09 IRONMONGERY 09
Item Item
REPAIRS TO IRONMONGERY Take Take
down down
and and set
clear aside for
away re-use
A B
Each $ $
09254 Group I type of article of ironmongery......................................................................................................................................................................... 5.10 8.40 09254
09255 Group II ditto................................................................................................................................................................................................................. 8.40 13.50 09255
09256 Group III ditto................................................................................................................................................................................................................ 26.90 59.00 09256
A
Each $
09257 Oil, ease, adjust and re-secure of article of ironmongery of any types........................................................................................................................................... 2.90 09257
(Note : Item 09257 shall not be measured when either of Items 09258 to 09260 inclusive is ordered.)
09258 Repair Group I article of ironmongery of any types including providing any parts and fittings as required and
including re-fixing upon repair (taking down article of ironmongery shall be measured separately if required)......................................................................... 36.50 09258
09259 Ditto but Group II article of ironmongery........................................................................................................................................................................................ 55.50 09259
09260 Ditto but Group III article of ironmongery...................................................................................................................................................................................... 161.50 09260
09261 Provide two new keys to lock each complete with chromium plated stamped label and split ring and including
re-fixing upon repair (taking down lock measured separately if required)..................................................................................................................................... 19.00 09261
09262 Provide new keys to cylinder lock from pattern of old complete with ditto (ditto)........................................................................................................................ 13.10 09262
09/20
09 IRONMONGERY 09
Item Item
TRANSLUCENT FILM SIGNAGE Size (m)
Add to
Signage comprising graphics, logos, letters, numbers, Chinese characters, full stops, commas, and 1.50m for
the like, cut from self adhesive translucent films and fixed on metal, plastic, or glass surfaces : - each
0.25 - 0.50 - 1.00 - additional
n.e. 0.25
0.50 1.00 1.50 0.50m or
part
thereof in
size
A B C D E
Each $ $ $ $ $
09263 Translucent film signage to existing plastic, glass and metal surfaces.................................................................. 81.80 140.70 351.70 451.90 77.50 09263
SILKSCREEN SIGNS
Silkscreen printed signs comprising graphics, logos, letters, numbers,
Chinese characters, full stops, commas, and the like : -
Each
09264 Silkscreen printing to existing plastic surfaces...................................................................................................... 51.80 84.30 164.20 250.10 71.60 09264
09265 Ditto to existing glass surfaces................................................................................................................................ 51.80 84.30 164.20 250.10 71.60 09265
09266 Ditto to existing metal surfaces............................................................................................................................... 51.80 84.30 164.20 250.10 71.60 09266
09267 Silkscreen printing with 3 mm thick white or coloured plastic sheet.................................................................... 72.80 120.70 244.80 354.70 91.50 09267
09268 Ditto but with 6 mm thick white or coloured plastic sheet.................................................................................... 94.10 161.30 323.30 460.20 114.10 09268
09269 Ditto but with 10 mm thick white or coloured plastic sheet.................................................................................. 121.10 208.00 430.40 613.40 152.50 09269
09270 Ditto but with 12.5 mm thick white or coloured plastic sheet............................................................................... 134.50 233.00 483.20 668.70 154.60 09270
09271 Silkscreen printing with 1.5 mm thick hairline stainless steel plate...................................................................... 107.70 183.40 374.60 527.90 127.80 09271
09272 Ditto but with 3 mm thick hairline stainless steel plate......................................................................................... 164.20 283.10 584.90 814.10 191.00 09272
09273 Ditto but with 1.5 mm thick mirror finished stainless steel plate.......................................................................... 109.90 185.30 378.70 533.40 128.90 09273
09274 Ditto but with 3 mm thick mirror finished stainless steel plate............................................................................. 166.30 286.40 586.40 814.10 189.90 09274
09275 Silkscreen printing with 1.5 mm thick aluminium plate........................................................................................ 73.70 121.10 249.70 356.90 89.30 09275
09276 Ditto but with 3 mm thick aluminium plate............................................................................................................ 96.40 163.70 331.60 471.40 116.50 09276
09/21
09 IRONMONGERY 09
Item Item
PLASTIC SIGNS Thickness (mm)
Add to
12mm for
each
additional
n.e. 3 3-6 6-9 9 - 12
3mm or
part
thereof in
thickness
A B C D E
Per square metre $ $ $ $ $
09277 Clear, white or coloured acrylic sheet..................................................................................................................... 113.20 226.40 339.60 452.80 94.30 09277
09278 Ditto but with matt finish........................................................................................................................................ 199.60 251.60 377.30 503.10 125.80 09278
09279 Clear, white or coloured acrylic sheet fixed with adhesive as laminated cover or backing sheet......................... 169.80 283.00 396.20 509.40 94.30 09279
09280 Ditto but with matt finish........................................................................................................................................ 188.70 314.40 440.20 566.00 104.80 09280
Per linear metre
09281 Cutting only acrylic sheet for features, graphics, etc. other than those measured elsewhere................................ 3.50 3.80 4.00 4.40 3.20 09281
Size (m)
Add to
1.50m for
each
0.25 - 0.50 - 1.00 - additional
n.e. 0.25
0.50 1.00 1.50 0.50m or
part
thereof in
size
A B C D E
Each $ $ $ $ $
09282 Engraved plastic sign face complete with letters, numbers, characters,
graphics, punctuations and the like, 3 mm thick.................................................................................................... 121.50 252.00 505.50 758.20 210.60 09282
09283 Ditto but 6 mm thick............................................................................................................................................... 143.30 297.70 600.20 882.70 236.40 09283
09284 Plastic sign complete with cut through letters, numbers, characters,
graphics, punctuations and the like, 3 mm thick.................................................................................................... 181.30 303.30 606.50 758.80 136.80 09284
09285 Ditto but through 4.50 mm thick sheet .................................................................................................................. 196.30 330.70 664.00 821.20 142.50 09285
09286 Ditto but through 6.00 mm thick sheet .................................................................................................................. 212.60 357.00 720.10 882.40 148.10 09286
09287 Ditto but through 10.00 mm thick sheet ................................................................................................................ 235.10 394.40 796.20 974.80 163.00 09287
09288 Ditto but through 12.50 mm thick sheet ................................................................................................................ 258.80 435.60 879.90 1,078.30 180.90 09288
09/22
09 IRONMONGERY 09
Item Item
PLASTIC SIGNS (CONT'D) Height (mm)
Add to
Plastic signs in letter, number or Chinese character : - 150mm
for each
additional
n.e. 25 25 - 50 50 - 100 100 - 150
50mm or
part
thereof in
height
A B C D E
Each $ $ $ $ $
09289 Letter or number cut from 3.00 mm thick sheet and fixed with adhesive ............................................................. 7.00 11.80 22.80 37.90 6.30 09289
09290 Ditto but from 4.50 mm thick sheet ditto ............................................................................................................... 8.50 17.00 34.00 43.00 7.50 09290
09291 Ditto but from 6.00 mm thick sheet ditto................................................................................................................ 14.70 24.40 48.80 77.30 19.00 09291
09292 Ditto but from 10.00 mm thick sheet ditto ............................................................................................................. 17.10 34.10 72.50 98.10 21.30 09292
09293 Ditto but from 12.50 mm thick sheet ditto ............................................................................................................. 22.60 45.30 90.50 145.50 45.80 09293
09294 Chinese character cut from 3.00 mm thick sheet and fixed with adhesive ........................................................... 8.10 13.40 26.80 46.30 16.20 09294
09295 Ditto but from 4.50 mm thick sheet ditto ............................................................................................................... 11.80 23.50 46.90 76.80 25.00 09295
09296 Ditto but from 6.00 mm thick sheet ditto................................................................................................................ 27.80 46.10 83.90 126.90 35.80 09296
09297 Ditto but from 10.00 mm thick sheet ditto.............................................................................................................. 29.40 58.70 119.50 181.80 51.90 09297
09298 Ditto but from 12.50 mm thick sheet ditto ............................................................................................................. 32.40 64.90 129.70 214.00 70.20 09298
Height (mm)
Add to
1000mm
for each
additional
n.e. 500 500 - 750 750 -1000
250mm or
part
thereof in
height
A B C D
Each $ $ $ $
09299 Letter or number cut from 8 mm thick plastic sheet with studs............................................................................................... 366.30 554.50 742.70 156.80 09299
09300 Ditto but from 10.00 mm thick sheet........................................................................................................................................ 407.00 616.10 825.20 174.30 09300
09301 Ditto but from 12.50 mm thick sheet........................................................................................................................................ 530.20 805.00 981.60 147.20 09301
09302 Chinese characters cut from 8 mm thick plastic sheet with studs............................................................................................ 535.30 791.60 1,047.80 213.50 09302
09303 Ditto but from 10.00 mm thick sheet........................................................................................................................................ 594.80 879.50 1,164.20 237.30 09303
09304 Ditto but from 12.50 mm thick sheet........................................................................................................................................ 803.90 980.30 1,266.70 248.60 09304
09/23
09 IRONMONGERY 09
Item Item
PLASTIC SIGNS (CONT'D) Size (m)
Add to
Plastic signs in letter, number or Chinese character : - (Cont'd) 1.50m for
each
0.25 - 0.50 - 1.00 - additional
n.e. 0.25
0.50 1.00 1.50 0.50m or
part
thereof in
size
A B C D E
Each $ $ $ $ $
09305 Take down and clear away plastic sheet sign from any position............................................................................ 3.40 5.10 8.40 10.10 1.30 09305
09306 Take down and set aside for re-use ditto................................................................................................................ 6.70 10.10 20.20 21.90 1.40 09306
09307 Fix only ditto............................................................................................................................................................ 10.10 15.20 27.00 30.40 2.70 09307
A
Each $
09308 Take down and clear away letters, numbers or Chinese characters of any size cut from plastic sheet from any position............................................................ 3.40 09308
09309 Take down and set aside for re-use ditto......................................................................................................................................................................................... 8.40 09309
09310 Fix only ditto.................................................................................................................................................................................................................................... 13.90 09310
METAL SIGNS Height (mm)
Add to
Metal signs in letter, number or Chinese character : - 300mm
for each
additional
n.e. 25 25 - 50 50 - 100 100 - 150 150 - 200 200 - 250 250 - 300
50mm or
part
thereof in
height
A B C D E F G H
Each $ $ $ $ $ $ $ $
09311 Letter or number cut from 3.00 mm thick anodized
aluminium sheet fixed with adhesive or screws .............................................. 21.00 41.10 83.60 119.90 166.00 212.20 258.30 30.70 09311
09312 Ditto but from 6.00 mm thick sheet ditto ......................................................... 30.40 60.90 125.60 168.50 295.40 344.60 383.30 32.20 09312
09313 Chinese character cut from 3.00 mm thick anodized aluminium
sheet fixed with adhesive or screws ................................................................. 26.60 53.30 109.80 196.50 283.30 370.00 456.70 57.80 09313
09314 Ditto but from 6.00 mm thick sheet ditto ......................................................... 52.30 104.80 214.00 276.10 346.50 417.70 487.60 58.80 09314
09315 Letter or number cut from 3.00 mm thick
brass sheet fixed with adhesive or screws......................................................... 30.40 68.00 139.10 239.50 339.90 440.30 540.70 83.70 09315
09316 Ditto but from 6.00 mm thick sheet ditto.......................................................... 60.10 111.90 235.20 335.80 436.50 537.10 637.70 83.90 09316
09317 Chinese character cut from 3.00 mm thick
brass sheet fixed with adhesive or screws ........................................................ 48.60 86.50 171.20 311.20 451.30 591.30 731.40 116.70 09317
09318 Ditto but from 6.00 mm thick sheet ditto ......................................................... 96.60 150.40 287.80 451.20 638.00 790.20 942.40 126.80 09318
09/24
09 IRONMONGERY 09
Item Item
METAL SIGNS (CONT'D) Height (mm)
Add to
Metal signs in letter, number or Chinese character : - (Cont'd) 1000mm
for each
additional
n.e. 500 500 - 750 750 -1000
250mm or
part
thereof in
height
A B C D
Each $ $ $ $
09319 Letter or number cut from 8 mm thick aluminium sheet with studs including baked paint finish and screws...................... 956.80 1,109.40 1,297.40 156.90 09319
09320 Ditto but from 10 mm thick sheet............................................................................................................................................. 1,076.50 1,248.10 1,459.90 176.50 09320
09321 Ditto but from 12 mm thick sheet............................................................................................................................................. 1,196.10 1,386.80 1,622.10 196.10 09321
09322 Chinese characters cut from 8 mm thick aluminium sheet with studs including baked
paint finish and screws.............................................................................................................................................................. 1,063.80 1,292.60 1,507.60 179.10 09322
09323 Ditto but from 10 mm thick sheet............................................................................................................................................. 1,126.40 1,454.20 1,696.00 201.50 09323
09324 Ditto but from 12 mm thick sheet............................................................................................................................................. 1,251.60 1,615.80 1,884.50 223.90 09324
Size (m)
Add to
1.50m for
each
0.25 - 0.50 - 1.00 - additional
n.e. 0.25
0.50 1.00 1.50 0.50m or
part
thereof in
size
A B C D E
Each $ $ $ $ $
09325 Acid etched stainless steel sign face, 1.5 mm thick................................................................................................ 223.20 446.40 892.80 1,339.20 372.00 09325
09326 Take down and clear away metal signs from any position..................................................................................... 2.10 3.20 6.40 7.40 0.90 09326
09327 Take down and set aside for re-use ditto................................................................................................................ 4.30 5.30 10.60 11.70 1.00 09327
09328 Fix only ditto............................................................................................................................................................ 7.20 10.60 19.70 21.10 1.10 09328
A
Each $
09329 Take down and clear away letters, numbers or Chinese characters of any size cut from metal sheet from any position.............................................................. 5.30 09329
09330 Take down and set aside for re-use ditto......................................................................................................................................................................................... 8.50 09330
09331 Fix only ditto.................................................................................................................................................................................................................................... 16.90 09331
09/25
09 IRONMONGERY 09
Item Item
HOLLOW METAL SIGNS Height (mm)
Add to
Hollow metal signs in letter, number or Chinese character : - 1000mm
for each
additional
n.e. 500 500 - 750 750 -1000
250mm or
part
thereof in
height
A B C D
Each $ $ $ $
09332 Letter or number cut and formed from stainless steel sheet not less than 1.2 mm thick with covered edge,
fixed at any height including all necessary fixing accessories................................................................................................. 359.90 539.70 719.60 163.00 09332
09333 Ditto but Chinese character....................................................................................................................................................... 449.80 674.60 899.60 202.30 09333
09334 Letter or number cut and formed from anodized aluminium sheet not less than 2 mm thick with
covered edge, fixed at any height including all necessary fixing accessories.......................................................................... 314.80 472.30 629.70 146.30 09334
09335 Ditto but Chinese character....................................................................................................................................................... 393.60 590.40 787.20 181.40 09335
Size (m)
Add to
2.00m for
each
0.50 - 1.00 - 1.50 - additional
n.e. 0.50
1.00 1.50 2.00 0.50m or
part
thereof in
size
A B C D E
Each $ $ $ $ $
09336 Logo or signage cut and formed from stainless steel sheet not less than 1.2 mm thick
with covered edge, including moulding, graphic finish, fixed at any height
and all necessary fixing accessories........................................................................................................................ 1,889.10 2,991.10 3,542.00 4,093.00 409.70 09336
09337 Ditto but cut and formed from anodized aluminium sheet not less than 2 mm thick............................................ 1,619.20 2,563.70 3,036.10 3,508.30 351.10 09337
Add to either of Items 09332 to 09337 inclusive for the supply of powder coated and baked paint finish.................................................................................. 20%
09/26
Section 10
STEEL AND METAL WORK
10 STEEL AND METAL WORK 10
SECTION 10
STEEL AND METAL WORK
SPECIAL CONDITIONS
Drawings SC10.01 The standard drawings for hoardings and walkways referred to in this Section and listed in
for hoardings Annex 'A' - Drawing Schedule and Drawings for Builder's Works of the Schedule can be
and walkways viewed on the ArchSD internet website via the pathway referred therein.
Measurement SC10.02 Throughout this Schedule, rates for all trades shall include for all temporary preventive
of hoardings and protective measures necessary for the execution of the work, such as to protect
and walkways new work or existing surfaces, and to protect the public from harm, dust or nuisance.
No payment will be made for hoardings and walkways under any circumstances, with
the following exceptions : -
(a) Hoardings and walkways are specifically ordered by the Maintenance
Surveyor in writing and stating that the hoarding and walkways are for the
exclusive use of the Employer and other contractor employed by the
Employer within the Works Order period.
In the event that the hoardings and walkways mentioned in sub-clause (a) above are
subsequently used as preventive and protective measures by the Contractor himself,
no payment will be made.
The hoardings and walkways shall be measured the length on plan as fixed.
No measurement or adjustment shall be made for concrete footings or anchor bolts.
Measurement SC10.03 Enhanced treatment to hoardings including graphic design proprietary graphical use
of enhanced film, plastic sheeting, painting and "green" features shall be measured the net area as
treatment to covered. No deduction shall be made for openings not exceeding 0.50 m.
hoardings
Measurement SC10.04 Throughout this Schedule, rates for all trades shall include for all temporary preventive and
of temporary protective measures necessary for the execution of the work such as to protect new work
work - Fire or existing surfaces, and to protect the public from harm, dust or nuisance. No payment
protection will be made for such work except additional requirement of fire protection enclosure
enclosure materials are specifically ordered by the Maintenance Surveyor in writing.
materials
Measurement SC10.05 Steel strutting, shoring, supporting and protective measures for the face of excavation have
of steel been allowed in the rates of Section 03 - Excavation in this Schedule. No payment will be
shoring made for these measures under any circumstance, with the following exception : -
(a) Steel strutting, shoring, bracings, supporting and the like in respect of the steel
sheet piling. Steel sheet piling must be specifically ordered by the Maintenance
Surveyor in writing.
Steel sections shall be measured the total weight as fixed. No deduction shall be made for
bolt holes, splays, notches and the like. The weight of the bolts and nuts shall be added.
10/1
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Measurement SC10.06 Structural steel work and metal work shall normally be measured by weight and shall
by weight be calculated in the following order of preference : -
(1) Measurements of the structural steel sections and metal sections and
reference to
(a) Annex 'C' - Tables of Metal Weights, etc. in this Schedule.
(b) Tables in British Standards or other International Standards.
(c) Tables in manufacturer's catalogues or similar documents.
(d) Unit weights calculated from the mass per cubic metre given in
Annex 'C' - Tables of Metal Weights, etc. in this Schedule.
or
(2) Weighed by the Contractor in the presence of the Maintenance Surveyor
before fixing, and in default of this, shall be taken out, weighed and re-fixed
by the Contractor at his own expense.
Measurement SC10.07 Structural steel work shall be paid only when it is specifically ordered by the
of structural Maintenance Surveyor in writing. Surface protection to structural steel shall be
steel work measured separately in Section 15 - Painting of this Schedule.
Measurement SC10.08 Metal sections shall be measured the length as fixed with square ends and the weight
of metal calculated.
sections
No deduction shall be made for rivet, screw and bolt holes, and notches or slots.
Measurement SC10.09 Mild steel (plain or galvanized) plate, stainless steel plate and aluminium plate, when
of sheet, flat exceeding 300 mm wide and not exceeding 3 mm thick shall be measured as sheet
bar or plate metal. When exceeding 3 mm thick, the same shall be measured as flat bar or
plate.
Measurement SC10.10 Sheet metal work shall be measured the area as fixed and the weight calculated. No
of sheet metal deduction shall be made for openings not exceeding 0.50 m. No addition shall be
made for rivets, screws, nuts, bolts and the like.
Perforated sheet metal work shall be measured the area as fixed. No deduction shall
be made in weight for factory-formed perforations of the sheet metal. No deduction
shall be made for openings cut on Site not exceeding 0.50 m.
Sheet or perforated sheet metal work shall include all sheet metal formed in any shape,
pattern, graphics, etc. and the like.
Measurement SC10.11 Except for holding down bolts for structural steelwork as stated in Special Conditions
of bolts and Clause SC10.30(d) and for bolts / anchor bolts required for replacement in isolated
anchor bolts repair items, of which the specified bolts shall be measured separately; all other types
for isolated of bolts / anchor bolts shall not be measured separately but shall deem to be included
repairs in the work items in this Section.
10/2
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Measurement SC10.12 Collapsible gate shall be measured the net weight calculated. No deduction shall be
of collapsible made for bolt holes, splays, notches and the like. The weight of bolts, nuts, rivets,
gate spacers, fixing lugs and the like, except ironmongeries, shall be added.
Measurement SC10.13 Items for sundry repairs in this Section of the Schedule shall not be measured except
of sundry under the following special circumstances : -
repairs
(a) Where the material and/or the labour of the work item to be repaired is not
measured and paid for separately under any other Schedule rates.
(b) Where the work item to be repaired requires labour, welding and fixing of the
work item at its existing position.
Measurement SC10.14 Corrugated and profiled sheet cladding (other than corrugated or profiled steel sheet
of corrugated roofing under Section 07 - Roofing and Waterproofing of this Schedule) shall be
and profiled measured flat (not girth on corrugations or profiles) over the net area covered with no
sheet cladding allowance for laps. No deduction shall be made for openings not exceeding 0.50 m.
Cladding to a radius not exceeding 15.00 m along the corrugation or profile shall be
measured as curved work.
Measurement SC10.15 Shutters shall be measured as the net area of the clear opening with reference to
of shutters drawing or reference to manufacturer's catalogue excluding any enclosures to the
shutter frames, linings, tracks, rails, hoods and the like.
"Extra over" for wicket door shall be measured the overall size of door.
Measurement SC10.16 Take down and set aside for re-use of existing shutters for repairs shall generally be
of Take down measured as net affected area.
and set aside
for re-use of The affected area means the damaged area including the individual module of each
shutters for affected slat or panel.
repairs
Measurement SC10.17 Cast iron, brass and copper articles shall be measured the net weight as cast and
of cast iron, finished ready for fixing.
brass and
copper
Measurement SC10.18 Metal windows and doors shall generally be measured net area of the structural
of metal opening of the windows and doors as fixed.
windows and
doors Extra over for opening sashes or doors shall be measured the overall size of the
generally opening sashes or doors.
Glazing to metal windows and doors shall be measured separately in Section 14
- Glazing of this Schedule.
10/3
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Measurement of SC10.19 Take down and clear away or Take down and set aside for re-use of existing
Take down and window and door shall generally be measured net area of the structural opening of the
clear away or window and door as fixed. No separate measurement will be made for openable sash,
Take down and ironmongery, fixing lugs, dowels, etc. and the like.
set aside for
re-use metal
window or door
Measurement SC10.20 Measurement of galvanized mild steel works shall include all processes of galvanizing
of galvanized in accordance with G.S. Items 15.63 and 17.02 for all raw materials and factory
steel works manufactured products.
Measurement SC10.21 Galvanizing, electro-plating and chromium shall be measured when the work has been
of galvanizing, fabricated on Site or off Site with further processing on Site required and is
electro-plating specifically ordered by the Maintenance Surveyor in writing. No payment will be
and chromium made for proprietary or factory manufactured products.
plating
Measurement of SC10.22 Zinc sprayed or hot dipped galvanizing shall only be measured when the mild steel
Zinc sprayed work has been fabricated (not factory manufactured products) and it is specifically
or Hot dipped ordered in writing by the Maintenance Surveyor.
galvanizing
Measurement of SC10.23 Composite aluminium cladding / panel linings shall be measured net on the area to be
proprietary cladded or covered. No deduction shall be made for opening not exceeding 0.50 m.
composite No measurement for additional materials required for bending, rolling edges, returns,
aluminium etc. and the like shall be made.
cladding / panel
linings
Measurement SC10.24 Curtain walls shall be measured the plane area of the curtain wall as fixed. No
of curtain walls deduction shall be made for opening not exceeding 0.50 m.
Measurement SC10.25 Proprietary automatic swing and sliding doors shall be measured the plane area of the
of proprietary door panel.
automatic
swing and
sliding doors
Measurement SC10.26 Slotted angle, galvanized steel tubing and wire rope shall be measured the net length
of slotted as fixed.
angle, tubing
and wire rope
Measurement SC10.27 Fire resisting door set shall be measured the plane area of the door panel.
of fire resisting
door set
10/4
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Measurement SC10.28 Proprietary fire resisting partitions shall generally be measured the plane area of
of proprietary panels. No deduction shall be made for voids or openings not exceeding 0.50 m.
fire resisting Finishes to the partition shall be measured separately.
partitions
Measurement SC10.29 Wire netting, wire mesh, welded wire mesh, expanded metal and chain link fencing
of wire netting, shall be measured the net area covered with no allowance for laps. No deduction shall
wire mesh, be made for openings not exceeding 0.50 m.
welded wire
mesh, expanded Irregular areas shall be measured the smallest square or rectangle size from which they
metal and can be cut.
chain link fencing
Various meshes sizes shall be measured in accordance with the British Standard
unless otherwise specified.
Rates generally SC10.30 The rates shall generally include for any or all of the following as applicable : -
(a) All straight, raking or circular cutting and waste.
(b) Lowering or hoisting to any depth or height and supporting, fitting and fixing
various items to new or existing work in any position including the provision
of all temporary supports and fastening, and grouting as required.
(c) All fabrication, assembling and erection work including riveting, drilling,
welding, brazing, either off Site or on Site as required.
(d) Providing throughout all ancillary materials for jointing and fixing, such as
welding rods, solders, screws, all types of bolts (except holding down bolts
for structural steelwork or otherwise specified), nuts and the like.
(e) Executing all work to true detail, filing all edges, welds, etc., smoothing, filing
off burrs around drilled holes, countersinking all screws, rivet heads and the
like when required and finishing work to the satisfaction of the Maintenance
Surveyor.
(f) Drilling and tapping holes, mortices and the like.
(g) Preparing new or existing surface for connection.
(h) Allowance for rolling margin.
(i) Building in, grouting and bedding, casting in and the application of bonding
agents, fillers and sealing materials.
(j) Sampling and testing of materials including submission of records.
(k) In the case of structural steel, sampling and testing of materials shall further
include all necessary security handling of samples, stock management on Site
and removal of non-compliant steel sections.
(l) Allowance for laps or seams.
(m) Providing of prototypes as G.S. Item 17.14.
10/5
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates generally SC10.30 (n) Protecting decorative finishes to metalwork.
(Cont'd) (Cont'd)
(o) Allowing all provisions of suitable connection point for equipotential bonding
as required by the I.E.E. Wiring Regulations.
Rates for SC10.31 The rates for hoardings and walkways shall include for : -
hoardings
and (a) Delivering to and erecting on Site, repairing and maintaining throughout the
walkways period of use in first or subsequent positions, and taking down and setting
aside for re-erection or clearing away.
(b) Providing all materials including poles, struts, wedges, plates, sheeting, bolts
and the like.
(c) Preparing and applying or touching up paint to all surfaces including writings
and logos in single or multi-colour paints.
(d) Providing and fixing anchor bolts, nuts and washers.
(e) Provision of concrete footing including associated earthwork, formwork and
reinforcement, if required.
(f) Providing adequate lightings and warning lights, associated power supply and
electrical work and payment of all charges incurred.
(g) Making good any damage caused to pavings and other surfaces during use,
erection and taking down.
(h) Payment for resurfacing of the pavings, roads, drainage system or any other
utilities in the event that making good is not allowed to be executed by the
Contractor.
Rates for SC10.32 The rates for temporary work - fire protection enclosure materials shall include for : -
temporary
work - fire (a) Working at any level, floor and locations.
protection
enclosure (b) All steel sections adequate for the fire rated period.
materials
(c) Finishing all fire protective boarding, metal plates, steel sections, etc. and the like
with intumescent paint, painting and colour coating.
(d) All concrete footing, base plate and anchor bolts including nuts and washers.
(e) Delivering to and erecting on Site, adjusting and maintaining throughout the period
of uses, and taking down and setting aside for re-use or removal from Site.
(f) Providing and forming temporary access door, ironmongeries and door seals.
(g) Providing, maintaining and clearing away after use adequate lighting and warning
lights, associated power supply and electrical work and payment of all charges
incurred.
(h) Cutting mortice or drilling in concrete, brick, stone or other surfaces as
required.
10/6
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates for SC10.32 (i) Sealing around edges with intumescent materials.
temporary (Cont'd)
work - fire (j) Grouting into new or existing mortice or holes.
protection
enclosure (k) Protecting and making good disturbed surfaces.
materials
(Cont'd) (l) Providing test certificate.
Rates for SC10.33 The rates for steel shoring shall further include for : -
steel
shoring (a) Working at any depth, height and locations.
(b) All steel sections such as round bars, squares, flats, plates, angles, tees,
channels, "I joists, hollow sections and the like.
(c) All anchor bolts and high friction grip bolts including nuts and washers.
(d) Any wedges as required.
(e) Delivering to and erecting on Site, adjusting and maintaining throughout the
period of uses, and taking down and setting aside for re-use or removal from
Site.
(f) Design and submission of calculation and working drawings of lateral support
including details of connections of walings, strutting, shoring, bracing, posts
and splicing of members and sequence of construction and sequence of
subsequent removal including endorsement by Registered Structural Engineer.
(g) Preparing and submitting method statement.
(h) Cleaning the interface of members to be jointed.
(i) Carrying out welding as G.S. Items 15.23 to 15.38.
(j) Grouting to joints as required.
(k) Protecting and making good existing surfaces disturbed.
Rates for SC10.34 The rates for structural steel works shall further include for : -
structural
steel works (a) Qualification tests for welders as G.S. Item 15.44 and submission of welding
record as G.S. Item 15.45.
(b) Approval tests of welding as G.S. Item 15.47.
(c) Test welded joints by non-destructive testing methods, and employing an
approved specialist firm to carry out and interpret these tests all as G.S.
Item 15.58.
(d) Making good damaged galvanized surfaces as G.S. Items 15.53 and
15.64.
10/7
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates for SC10.34 (e) Providing manufacturers' certificates as G.S. Item 15.13.
structural (Cont'd)
steel works (f) Marking for identification on all materials as G.S. Item 15.14, protection
(Cont'd) from damage and delivery in matching sequence.
Rates for SC10.35 The rates for mild steel shall further include for : -
mild steel
(a) Forging, notching, framing and bending.
(b) Pointed, forged, fanged and threaded ends.
(c) Mitres angles, ramps and wreaths.
(d) Spot, fillet and seam welding.
Rates for SC10.36 The rates for sheet metal work shall further include for : -
sheet
metal work (a) Notching, dressing, bending and rolled edges.
(b) Punching holes.
(c) Plugging or drilling existing surfaces.
(d) Fixing with an approved adhesive.
Rates for SC10.37 The rates for lining, ducting, gutters, ventilator and the like shall further include for : -
lining,
ducting, (a) Notching, dressing, bending and rolled edges.
gutters,
ventilator (b) Punching holes.
and the
like (c) Plugging or drilling existing surfaces.
(d) Fixing with an approved adhesive.
(e) All bends, ends, inlets, outlets, junctions, connections, flanged joints and the
like.
(f) Forming perforations (gross weight measured).
(g) Fixing to wood or metal framing with or without brackets (framing and
brackets measured separately).
Rates for SC10.38 The rates for collapsible gates shall further include for : -
collapsible
gates (a) Framing to head, jambs, top and bottom guides.
(b) Fixing blocks, pickets, diagonal folding item bars and fixing lugs.
(c) Riveted pivot points with brass washers and spacers.
10/8
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates for SC10.38 (d) Supply and fixing of ball bearing rollers, retaining catches, catch hook, brass
collapsible (Cont'd) pull handles, lock and all necessary ironmongeries.
gates
(Cont'd) (e) Forming pockets in existing structure, grouting in with cement mortar and
making good.
Rates for SC10.39 The rates for bolts and anchor bolts for isolated repairs shall further include for : -
bolts and
anchor bolts (a) Cutting mortice or drilling in concrete, brick, stone or other surfaces as
for isolated required.
repairs
(b) Grouting into new or existing mortice or holes.
(c) Providing and fixing with nuts and washers.
(d) Making good disturbed surfaces.
(e) Components and devices for grouping and tying anchor bolts to form
assemblies of bolts.
Rates for SC10.40 The rates for corrugated and profiled sheet cladding shall further include for : -
corrugated
and (a) Works at any height and locations.
profiled
sheet (b) Works to new or existing surfaces in repairs.
cladding
(c) Provision of sub-frames, backing frames and purlin system including design
and submission of RSE structural calculations and shop drawings.
(d) Forming and including joints and allowing for laps including side and end laps
when required.
(e) Allowing for cutting, waste and breakage.
(f) Sealing at edges, joints and around intersections and projections.
(g) All narrow widths and small areas.
(h) Providing shop drawings as necessary for the works.
(i) Making good affected areas to match existing.
(j) Allowing all notching and fitting edges of sheets and mitring corners as
required, and all mitred angles, junctions and ends.
(k) Drilling holes for and providing all drive screws, self-tapping screws, rivets,
bolts, hook bolts, nuts, metal and rubber washers, and plastic caps for fixing
to purlins or framing spaced at any interval.
(l) Drilling holes to existing or new purlins of framing spaced at any interval for
the fixing of corrugated and profiled sheet cladding.
(m) Forming holes for pipes or articles.
10/9
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates for SC10.40 (n) Recommended fixing method in accordance with the manufacturer's
corrugated (Cont'd) instructions.
and
profiled (o) Forming and including movement joints as required.
sheet
cladding (p) Forming sheets to required curvature.
(Cont'd)
Rates for SC10.41 The rates for tubular metal work shall further include for : -
tubular metal
work (a) Framing and bending.
(b) Cut and welded junctions, angles, tees and cross joints.
(c) Flanged or screw fitting connectors.
(d) Screw fitting bends, tees, crosses and flanges.
(e) Ramps, wreaths and fanged, fair and capped ends.
Rates for SC10.42 The rates for stainless steel shall further include for : -
stainless steel
(a) Items described as trim or cover strip shall include for cutting to length and
mitred angles.
(b) Finishing all welds, etc. to match the finish specified.
(c) Treatment on surfaces in contact with concrete or dissimilar metals with one
coat of bituminous paint on stainless steel surfaces or using an approved tape.
Rates for SC10.43 The rates for aluminium shall further include for : -
aluminium
(a) Clear anodized finish.
(b) Items described as trim or cover strip shall include for cutting to length and
mitred angles.
(c) Ramps, wreaths and flanged, fair and capped ends.
(d) Treatment on surfaces in contact with concrete or dissimilar metals with one
coat of bituminous paint on aluminium surfaces or using an approved tape.
Rates for wire SC10.44 The rates for wire netting, wire mesh, welded wire mesh, expanded metal and chain
netting, wire link fencing shall further include for : -
mesh, welded
wire mesh, (a) All bending and notching required.
expanded
metal and chain (b) Allowance for side and end laps.
link fencing
(c) Allowance for spot weld, staples, tying wire, strained wire and the like as
required.
10/10
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates for SC10.45 The rates for steel windows and doors shall further include for : -
steel windows
and doors (a) Providing steel clamps to all opening lights of casements as G.S. Item
17.32 (o).
(b) Providing and fixing galvanized mild steel glazing beads and drips, if required.
(c) Providing and fixing galvanized mild steel fixing lugs or anchor bolts as
required.
(d) Providing and fixing all necessary ironmongeries of any types of surface finish
and materials except torque arm control system.
(e) Providing drawings as G.S. Item 17.34.
(f) Providing sample as G.S. Item 17.35.
(g) Raking joints, pointing, masking, cleaning as G.S. Item 17.36 (i).
(h) Making good disturbed surfaces.
(i) Protecting and cleaning.
Rates for SC10.46 The rates for repairs to metal windows and doors shall further include for : -
repairs to
metal (a) Providing ironmongery of matching materials and finishes
windows and
doors (b) Cutting at all means.
(c) Drilling and tapping to existing framing including riveting and welding.
(d) Providing and fixing screws, rivets, etc. and the like.
(e) Cutting mortices and grouting in cement mortar and making good
disturbed surfaces.
(f) Making good disturbed surfaces.
(g) Protecting and cleaning.
Rates for SC10.47 The rates for aluminium windows and doors shall further include for : -
aluminium
windows (a) Providing all necessary galvanized steel fixing lugs and the like as G.S.
and doors Item 17.33 (e).
(b) Providing galvanized steel water bars as G.S. Item 17.33 (f).
(c) Providing and fixing all necessary ironmongeries, fittings and furniture as G.S.
Items 17.33 (k) to 17.33 (m) except remote control system.
(d) Providing and fixing all necessary weather strip as G.S. Item 17.33(h).
(e) Providing drawings as G.S. Item 17.34.
10/11
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates for SC10.47 (f) Providing sample as G.S. Item 17.35.
aluminium (Cont'd)
windows (g) Bedding frames as G.S. Item 17.36 (h).
and doors
(Cont'd) (h) Raking joints, pointing, masking, cleaning as G.S. Item 17.36 (j).
(i) Treatment on surfaces in contact with concrete or dissimilar metals with one
coat of bituminous paint on aluminium surfaces or using an approved tape.
Rates for SC10.48 The rates for curtain walls shall further include for : -
curtain
walls (a) The design of the curtain walls to comply with the maximum Overall Thermal
Transfer Values (OTTV) for building (including walls and roof) of 23 w/m or
less.
(b) All submissions of information as required in G.S. Item 16.07.
(c) Requirements pursuant to codes and standards as G.S. Item 16.05 and an
itemized list of deviations from the Specification and Drawings for the works.
(d) Submission of drawings and calculations as G.S. Item 16.09.
(e) Submission of samples, mock-up erection and tests.
(f) Method statement related to jointing of components, fire barriers between
perimeters of floors and curtain wall, programme for the works, erection and
any remedial works.
(g) In the case of aluminium curtain walls, all types of anodized finishes, powder
coated, organic coating fluorocarbon coated or PVF2 finishes.
(h) In the case of stainless steel curtain walls, all types of polished finishes.
(i) Reinforcing members, sub-frames and the like of any material.
(j) Fixing, connections and provision of anchorages.
(k) Openable windows and doors, integral louvres and associated ironmongeries
and fittings.
(l) Spandrels, stone panels and their supporting systems.
(m) Cills, copings, water bars, flashings, seals and other attachments including
dressing to roofs/abutments.
(n) Isolation of dissimilar metals and moving parts.
(o) Support fire-saving insulation on galvanized steel support clips spaced at a
maximum of 450 mm centres.
(p) Preparation work to adjoining structure for attachment of curtain wall.
(q) All glass and glazing work.
10/12
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates for SC10.48 (r) All tests, at field or in laboratories, and report work.
curtain (Cont'd)
walls (s) Sealing joints within curtain wall and joints to existing.
(Cont'd)
(t) Provision of reports, manufacturer's guarantee, maintenance manuals and
deed of warranty, if required.
(u) Provision of anchors for gondola.
(v) Provision of lightning protection.
(w) Provision of Field or Site mock-up.
(x) Provision of closure panel for venetian blind/shutter.
(y) Provision of waterproofing/water-tightness.
(z) Protection and cleaning.
Rates for SC10.49 The Special Conditions for Section 09 - Ironmongery in this Schedule shall
ironmongery apply equally to all items of ironmongery in this Section.
Rates for SC10.50 The rates for proprietary composite aluminium cladding shall further include for : -
proprietary
composite (a) Design, supply, fabrication and installation of composite aluminium cladding.
aluminium
cladding (b) Applying and installation of composite aluminium cladding panels to walls,
bulkheads, ceiling soffits or any other locations.
(c) Submission of structural design, calculations and drawings endorsed by a
Registered Structural Engineer.
(d) Submission of details related to quality, coating finish, thickness and standard
of aluminium and galvanized mild steel reinforcement together with the
manufacturer's certification, for the Maintenance Surveyor's approval.
(e) Submission of design drawings, working details and shop drawings for
Maintenance Surveyor's approval prior to commencement of installation.
(f) Submission of samples and carrying out of mock-up erection and testing
including all necessary tests required to ensure the integrity and safety of the
cladding and associated support and fixing system.
(g) Submission of method statements related to jointing of components,
programme for the work, erection and any remedial works.
(h) All types of finishes to the cladding panels and bending to suit all shapes and
configurations.
(i) Support framework constructed of reinforcing members, backing materials,
framing, stiffeners and the like of any materials.
(j) Fixing, connections, angle brackets and provision of all types of anchorages
including bolts, nuts and the like.
10/13
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates for SC10.50 (k) Openable access doors, louvres and openings for building services
proprietary (Cont'd) installation.
composite
aluminium (l) Ironmongeries and fittings.
cladding
(Cont'd) (m) Forming opening around door and/or window.
(n) Provision of anchorage for gondolas, where required.
(o) Provision of waterproofing and water-tightness.
(p) Provision of lightning protection.
(q) Isolation of dissimilar metals, moving parts and provision of lubrication.
(r) Support fire-saving insulation on galvanized steel support clips spaced at a
maximum of 450 mm centres.
(s) Preparation work to adjoining structure for attachment of cladding.
(t) Sealing joints within cladding and joints to existing.
(u) Concealed and exposed flashings, edge trims and the like.
(v) Provision of all necessary test reports, maintenance manuals and
manufacturer's guarantee.
(w) Protection and cleaning.
Rates for SC10.51 Where the proprietary composite aluminium cladding is applied / installed at ceiling
proprietary soffits, the rates for proprietary composite aluminium cladding shall further include for : -
composite
aluminium (a) Design, supply, fabrication and installation of the whole suspension system
cladding to (i.e. suspension framing, edge trims, runners, hangers and the like and fixing
ceiling to concrete soffits).
(b) Edge trims at junction with bulkheads.
(c) All cutting and narrow widths.
(d) Unless otherwise stated, any drop length from soffits.
(e) Forming openings and trimming around pipes, conduits, power points
and the like including extra supports and trimmers for the same.
(f) Trimming around sprinkler and detector heads, air grilles, light fittings,
access panels and the like including extra supports and trimmers for
the same.
(g) Additional framing and supports, etc. to bridge across ducts and the like.
10/14
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates for SC10.52 The rates for composite aluminium lining shall further include for : -
composite
aluminium (a) Design, supply, fabrication and installation of aluminium lining for internal use.
lining
(b) Submission of details related to quality, coating finish, thickness and standard
of aluminium and galvanized mild steel reinforcement together with the
manufacturer's certification, for the Maintenance Surveyor's approval.
(c) Submission of design drawings, working details and shop drawings for
Maintenance Surveyor's approval prior to commencement of installation.
(d) Submission of samples and carrying out of mock-up erection.
(e) Submission of method statements related to jointing of components,
programme for the work, erection and any remedial works.
(f) All types of finishes to the panel lining and bending to suit all shapes and
configurations.
(g) Support framework constructed of reinforcing members, backing materials,
framing, stiffeners and the like of any materials.
(h) Fixing, connections, angle brackets and provision of all types of anchorages
including bolts, nuts and the like.
(i) Openable access doors, louvres and openings for building services installation.
(j) Ironmongeries and fittings.
(k) Forming opening around door and/or window.
(l) Provision of lightning protection.
(m) Isolation of dissimilar metals, moving parts and provision of lubrication.
(n) Preparation work to adjoining structure for attachment of cladding.
(o) Sealing joints within panels of linings and joints to existing.
(p) Provision of all necessary test reports, maintenance manuals.
(q) Protection and cleaning.
Rates for SC10.53 The rates for shutters shall further include for : -
shutters
(a) Cutting mortice, sinking or drilling in concrete, brick, stone or other surfaces
as required.
(b) Grouting into new or existing mortice or holes.
(c) Providing and fixing with nuts and washers.
(d) Providing and fixing hinges, locking device, lock and all necessary
ironmongeries.
10/15
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates for SC10.53 (e) Making good disturbed surfaces.
shutters (Cont'd)
(Cont'd) (f) Provision of connection to nearest power point by registered electrical
workers for any electrically operated shutters.
Rates for SC10.54 The rates for fire resisting roller shutters shall further include for : -
fire resisting
roller shutters (a) Supply and installation in accordance with the manufacturer's instructions,
Particular Specification and in compliance with statutory requirements.
(b) Providing and fixing self closing mechanism activated by smoke detector(s)
and manual control device(s) on both side of the wall openings for automatic
and manual operation compliance with the Fire Service Installation if
Government Buildings, Architectural Services Department, and all
accessories, ironmongeries and the like recommended by the manufacturer.
(c) Cutting mortice or drilling in concrete, brick, stone or other surfaces as
required.
(d) Grouting into new or existing mortice or holes.
(e) Providing back up power supply.
(f) Connecting to fire alarm system when required.
(g) Finishing all surfaces as required.
(h) Providing test certificate, operation manuals and manufacturer's guarantee.
(i) Provision of connection to nearest power point by registered electrical
workers for any electrically operated fire resisting roller shutters.
Rates for SC10.55 The rates for transparent shutters shall further include for : -
transparent
shutters (a) Supply and installation in accordance with the manufacturer's instructions.
(b) Cutting mortice, sinking or drilling in concrete, brick, stone or other surfaces
as required.
(c) Grouting into new or existing mortice or holes.
(d) Providing and fixing with nuts and washers.
(e) Providing and fixing typhoon shutter guide with locking device.
(f) Providing and fixing hinges, locking device, lock and all necessary
ironmongeries.
(g) Making good disturbed surfaces.
(h) Providing test certificate, operation manuals and manufacturer's guarantee.
10/16
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates for fire SC10.56 The rates for fire resisting doors shall further include for : -
resisting doors
(a) Supply and installation in accordance with the manufacturer's instructions and
in compliance with statutory requirements.
(b) Providing and fixing door frames, all accessories, ironmongeries and the like
recommended by the manufacturer (panic bolt, emergency panic device and
digital locking device measured separately).
(c) Providing back up power supply when required.
(d) Cutting mortice or drilling in concrete, brick, stone or other surfaces as
required.
(e) Grouting into new or existing mortice or holes.
(f) Finishing all surfaces as required.
(g) Making good disturbed surfaces.
(h) Providing test certificate, operation manuals and manufacturer's guarantee.
Rates for SC10.57 The rates for proprietary automatic swing and sliding doors shall further include for : -
proprietary
automatic swing (a) Supply and installation in accordance with the manufacturer's instructions.
and sliding doors
(b) Providing and fixing door frames, door operator, automatic mechanism,
interlocking devices and all necessary accessories, ironmongeries and the like
recommended by the manufacturer.
(c) Providing clear tempered glass door panel or observation panel.
(d) Providing back up power supply.
(e) Cutting mortice or drilling in concrete, brick, stone or other surfaces as
required.
(f) Grouting into new or existing mortice or holes.
(g) Finishing all surfaces as required.
(h) Making good disturbed surfaces.
(i) Providing test certificate, operation manuals and manufacturer's guarantee.
(j) Provision of connection to nearest power point by registered electrical
workers.
10/17
10 STEEL AND METAL WORK 10
SPECIAL CONDITIONS
Rates for SC10.58 The rates for proprietary fire resisting partitions shall further include for : -
proprietary fire
resisting partitions (a) Supply and installation in accordance with the manufacturer's instructions and
in compliance with statutory requirements.
(b) Cutting mortice or drilling in concrete, brick, stone or other surfaces as
required.
(c) Grouting into new or existing mortice or holes.
(d) Finishing both sides of partition with fire resisting boarding/material.
(e) Making good disturbed surfaces.
(f) Providing test certificate, operation manuals and manufacturer's guarantee.
Rates for SC10.59 The rates for fibreglass house and planter shall further include for : -
fibreglass
house and (a) All necessary accessories recommended by the manufacturer.
planter
(b) Fixing to concrete base or steel support (measured separately) including
anchor bolts.
G.S. clauses SC10.60 G.S. clauses for the following items can be found in the respective sections of the
General Specification for Building as listed below : -
(a) Steel sheet cladding - Section 12 - Roofing.
(b) Fencing and gates - Section 24 - External Works.
(c) Structural steel work - Section 15 - Structural Steel Work.
(d) Curtain walls - Section 16 - Curtain Walls.
(e) Corrugated and - Section 12 - Roofing.
profiled sheeting
cladding
(f) Strong room doors - Section 22 - Internal Fittings and Fixtures.
10/18
10 STEEL AND METAL WORK 10
Item Item
STEEL SHORING
Erect, Erect,
The following Items 10001 to 10002 inclusive will only be paid in accordance with Special Conditions maintain, maintain,
Clause SC10.05 : - take down and
and clear left-in
away position
A B
Per kg $ $
10001 Steel shoring to support surface of excavation............................................................................................................................................................. 8.00 7.10 10001
10002 Steel shoring to support existing building or structure................................................................................................................................................ 9.80 8.50 10002
HOARDINGS AND WALKWAYS
The following Items 10003 to 10023 inclusive will only be paid in accordance with Special Conditions
Clause SC10.02 :-
Erect, Erect,
Note: The standard drawings for hoardings and walkways referred to in this Section are listed in Annex A - maintain, maintain,
Drawing Schedule and Drawings of the Schedule and can be viewed on the ArchSD internet website take down and
via the pathway referred therein. and clear left-in
away position
A B
Per linear metre $ $
10003 Type A hoarding corrugated steel fence as detailed on drawings 9711/A/A01 to 9711/A/A05
and 9711/A/S01 to 9711/A/S04.................................................................................................................................................................................... 1,051.00 998.10 10003
10004 Type E hoarding corrugated steel fence (surface-mounted footing) as detailed on drawings
9711/E/A01 to 9711/E/A05 and 9711/E/S01 to 9711/E/S04...................................................................................................................................... 1,247.50 1,185.20 10004
Each
10005 Gateway for Type A hoarding corrugated steel fence as detailed on drawings 9711/A/A01 to 9711/A/A05
and 9711/A/S01 to 9711/A/S04.................................................................................................................................................................................... 12,514.00 11,888.40 10005
10006 Gateway for Type E hoarding corrugated steel fence (surface-mounted footing) as detailed on drawings
9711/E/A01 to 9711/E/A05 and 9711/E/S01 to 9711/E/S04...................................................................................................................................... 14,059.00 13,356.00 10006
Erect, maintain, Erect, maintain
take down and clear away and left-in position
with walkway of with walkway of
minimum clear width minimum clear width
1.1 m 1.4 m 2.0 m 1.1 m 1.4 m 2.0 m
A B C D E F
Per linear metre $ $ $ $ $ $
10007 Type B hoarding covered walkway as detailed on drawings
9711/B/A01 to 9711/B/A07 and 9711/B/S01 to 9711/B/S05.............................................................. 2,780.90 2,919.90 3,337.10 2,641.80 2,773.90 3,170.20 10007
10008 Type C hoarding covered walkway with single deck catch
platform as detailed on drawings 9711/C/A01 to 9711/C/A07
and 9711/C/S01 to 9711/C/S05............................................................................................................ 4,267.90 4,481.30 5,121.50 4,054.50 4,257.20 4,865.40 10008
10009 Type D hoarding covered walkway with double deck catch
platform as detailed on drawings 9711/D/A01 to 9711/D/A07
and 9711/D/S01 to 9711/D/S05............................................................................................................ 5,677.70 5,961.50 6,813.20 5,393.80 5,663.40 6,472.60 10009
10/19
10 STEEL AND METAL WORK 10
Item Item
HOARDINGS AND WALKWAYS (CONT'D) Erect, maintain, Erect, maintain
take down and clear away and left-in position
with walkway of with walkway of
minimum clear width minimum clear width
1.1 m 1.4 m 2.0 m 1.1 m 1.4 m 2.0 m
A B C D E F
Per linear metre $ $ $ $ $ $
10010 Type F hoarding covered walkway (surface-mounted footing) as detailed
on drawings 9711/F/A01 to 9711/F/A07 and 9711/F/S01 to 9711/F/S05........................................... 2,974.00 3,122.70 3,568.80 2,825.30 2,966.50 3,390.40 10010
Erect, maintain, Erect, maintain
take down and clear away and left-in position
with walkway of with walkway of
minimum clear width minimum clear width
1.35m 1.60m 1.85m 1.35m 1.60m 1.85m
A B C D E F
Per linear metre $ $ $ $ $ $
10011 Type G1 hoarding covered walkway with single deck catch
platform (surface-mounted footing) as detailed on drawings
9711/G1/A01 to 9711/G1/A09 and 9711/G1/S01 to 9711/G1/S05..................................................... 4,461.00 4,856.60 4,996.30 4,238.00 4,613.80 4,746.50 10011
10012 Type H1 hoarding covered walkway with double deck catch
platform (surface-mounted footing) as detailed on drawings
9711/H1/A01 to 9711/H1/A09 and 9711/H1/S01 to 9711/H1/S05..................................................... 5,974.60 6,517.70 6,691.50 5,675.80 6,191.80 6,356.90 10012
Erect, maintain, Erect, maintain
take down and clear away and left-in position
with walkway of with walkway of
minimum clear width minimum clear width
1.85m 2.43m 3.00m 1.85m 2.43m 3.00m
A B C D E F
Per linear metre $ $ $ $ $ $
10013 Type G2 hoarding covered walkway with single deck catch
platform (surface-mounted footing) as detailed on drawings
9711/G2/A01 to 9711/G2/A08 and 9711/G2/S01 to 9711/G2/S05..................................................... 4,996.30 5,749.00 6,488.80 4,746.50 5,461.60 6,164.30 10013
10014 Type H2 hoarding covered walkway with double deck catch
platform (surface-mounted footing) as detailed on drawings
9711/H2/A01 to 9711/H2/A08 and 9711/H2/S01 to 9711/H2/S05..................................................... 6,691.50 7,699.60 8,690.30 6,356.90 7,314.70 8,215.80 10014
10/20
10 STEEL AND METAL WORK 10
Item Item
HOARDINGS AND WALKWAYS (CONT'D) Erect, maintain, Erect, maintain
take down and clear away and left-in position
with walkway of with walkway of
minimum clear width minimum clear width
1.1 m 1.4 m 2.0 m 1.1 m 1.4 m 2.0 m
A B C D E F
Each $ $ $ $ $ $
10015 Gateway for Type B hoarding covered walkway as detailed on drawings
9711/B/A01 to 9711/B/A07 and 9711/B/S01 to 9711/B/S05.............................................................. 24,139.70 25,346.70 28,967.60 22,936.70 24,079.30 27,519.30 10015
10016 Gateway for Type C hoarding covered walkway with single deck catch
platform as detailed on drawings 9711/C/A01 to 9711/C/A07
and 9711/C/S01 to 9711/C/S05............................................................................................................ 30,589.80 32,119.30 36,707.80 29,060.30 30,519.40 34,872.40 10016
10017 Gateway for Type D hoarding covered walkway with double deck catch
platform as detailed on drawings 9711/D/A01 to 9711/D/A07
and 9711/D/S01 to 9711/D/S05............................................................................................................ 30,589.80 32,119.30 36,707.80 29,060.30 30,519.40 34,872.40 10017
10018 Gateway for Type F hoarding covered walkway (surface-mounted footing)
as detailed on drawings 9711/F/A01 to 9711/F/A07
and 9711/F/S01 to 9711/F/S05............................................................................................................. 23,174.10 24,332.80 27,808.90 22,015.40 23,116.20 26,418.50 10018
Erect, maintain, Erect, maintain
take down and clear away and left-in position
with walkway of with walkway of
minimum clear width minimum clear width
1.35m 1.60m 1.85m 1.35m 1.60m 1.85m
A B C D E F
Each $ $ $ $ $ $
10019 Gateway for Type G1 hoarding covered walkway with single deck
catch platform (surface-mounted footing) as detailed on drawings
9711/G1/A01 to 9711/G1/A09 and 9711/G1/S01 to 9711/G1/S05..................................................... 30,589.80 32,119.30 36,707.80 29,060.30 30,519.40 34,872.40 10019
10020 Gateway for Type H1 hoarding covered walkway with double deck
catch platform (surface-mounted footing) as detailed on drawings
9711/H1/A01 to 9711/H1/A09 and 9711/H1/S01 to 9711/H1/S05..................................................... 30,589.80 32,119.30 36,707.80 29,060.30 30,519.40 34,872.40 10020
10/21
10 STEEL AND METAL WORK 10
Item Item
HOARDINGS AND WALKWAYS (CONT'D) Erect, maintain, Erect, maintain
take down and clear away and left-in position
with walkway of with walkway of
minimum clear width minimum clear width
1.85m 2.43m 3.00m 1.85m 2.43m 3.00m
A B C D E F
Each $ $ $ $ $ $
10021 Gateway for Type G2 hoarding covered walkway with single deck
catch platform (surface-mounted footing) as detailed on drawings
9711/G2/A01 to 9711/G2/A08 and 9711/G2/S01 to 9711/G2/S05..................................................... 30,589.80 32,119.30 36,707.80 29,060.30 30,519.40 34,872.40 10021
10022 Gateway for Type H2 hoarding covered walkway with double deck
catch platform (surface-mounted footing) as detailed on drawings
9711/H2/A01 to 9711/H2/A08 and 9711/H2/S01 to 9711/H2/S05..................................................... 30,589.80 32,119.30 36,707.80 29,060.30 30,519.40 34,872.40 10022
Erect, Erect,
maintain, maintain,
take down and
and clear left-in
away position
A B
Per linear metre $ $
10023 Extra over either of Items 10003 to 10004, 10007 to 10014 inclusive for toe sheet as detailed on drawings 9711/A/A03,
9711/B/A03, 9711/C/A03, 9711/D/A03, 9711/E/A03, 9711/F/A03, 9711/G1/A08, 9711/G2/A08, 9711/H1/A08 and 9711/H2/A08.................. 14.00 12.00 10023
ENHANCED TREATMENT TO HOARDINGS
(Note : - The following Items 10024 to 10027 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
A
Per square metre $
10024 Apply graphic design proprietary graphical use film, plastic sheeting or painting to hoarding surface ...................................................................................... 252.00 10024
10025 Apply "green" feature including suitable climbing plants and mesh to hoarding surface............................................................................................................. 126.00 10025
Per linear metre
10026 Transparent polycarbonate sheet hoarding 2 m high ..................................................................................................................................................................... 2,261.50 10026
10027 Hang flower pot at approximately 2 m intervals including support hanging brackets to hoarding ............................................................................................. 63.00 10027
10/22
10 STEEL AND METAL WORK 10
Item Item
TEMPORARY WORK - FIRE PROTECTION ENCLOSURE Erect, Erect,
maintain, maintain,
The following Items 10028 to 10029 inclusive will only be paid in accordance with Special Conditions take down and
Clause SC10.04 : - and clear left-in
away position
A B
Per square metre $ $
10028 Temporary enclosure with fire protection material of 1 hour fire rated period.......................................................................................................... 287.00 352.00 10028
10029 Ditto but 2 hour fire rated period.................................................................................................................................................................................. 682.00 783.00 10029
STRUCTURAL STEEL WORK Take Take
Supply and fix down down Fix
HOT ROLLED STEEL and and set only
Grade Grade clear aside for
S275 S355 away re-use
A B C D E
Per kg $ $ $ $ $
10030 Round rods, square rods, flat bars, plates, angle sections, tee sections,
universal beams, columns, channels or "I" joists.................................................................................................... 24.20 24.10 4.50 5.10 12.10 10030
10031 Rectangular, square or circular hollow sections..................................................................................................... 26.40 26.40 4.50 5.10 13.30 10031
10032 Fabricated small items n.e. 2 kg each..................................................................................................................... 27.50 27.50 4.50 6.40 15.70 10032
COLD ROLLED STEEL TO BS EN 10162 Take Take
Supply down down Fix
(Note : The following Items 10033 to 10035 inclusive will only be paid for, if ordered by the and and and set only
Maintenance Surveyor in writing.) fix clear aside for
away re-use
A B C D
Per kg $ $ $ $
10033 Angle or tee sections, channels, lipped channels or lipped "Z" sections, non-standard purlin sections
or other similar sections............................................................................................................................................................ 29.30 4.50 5.10 12.10 10033
10034 Rectangular, square or circular hollow sections....................................................................................................................... 33.40 4.50 5.10 13.30 10034
10035 Fabricated small items n.e. 2 kg each....................................................................................................................................... 35.40 4.50 6.40 15.70 10035
10/23
10 STEEL AND METAL WORK 10
Item Item
STRUCTURAL STEEL WORK (CONT'D)
HOLDING DOWN BOLTS Size
M16 M20 M24
A B C
Each $ $ $
10036 Holding down bolt, Grade 4.6 to B.S. 7419, n.e. 300 mm long complete with nuts and washers .......................................................... 115.20 127.00 143.10 10036
10037 Ditto but 300 - 450 mm long....................................................................................................................................................................... 150.30 160.60 179.30 10037
10038 Ditto but 450 - 600 mm long....................................................................................................................................................................... 174.90 183.70 204.30 10038
10039 Holding down bolt, Grade 8.8 to B.S. 7419, n.e. 300 mm long complete with nuts and washers .......................................................... 125.10 141.70 164.20 10039
10040 Ditto but 300 - 450 mm long....................................................................................................................................................................... 162.20 176.70 203.40 10040
10041 Ditto but 450 - 600 mm long....................................................................................................................................................................... 189.40 201.70 230.60 10041
MILD STEEL Take Take
Supply down down Fix
ROLLED SECTIONS AND PLATE and and and set only
fix clear aside for
away re-use
A B C D
Per kg $ $ $ $
10042 Round rods, square rods, flat bars, plates, chequer plates, angle sections, tee sections,
universal beams, columns, channels or "I" joists...................................................................................................................... 17.20 4.50 5.10 8.40 10042
10043 Rectangular, square or circular hollow sections....................................................................................................................... 18.70 4.50 5.10 8.40 10043
SHEET METAL WORK Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per kg $ $ $ $
10044 Flat or formed sheet covering ................................................................................................................................................... 23.00 3.20 3.80 7.60 10044
10045 Sheet lining to brick or concrete duct, sheet as ducting, pipes, gutters, funnels,
hoods, chimney cowls, roof plates and the like........................................................................................................................ 29.40 3.80 5.70 11.00 10045
10046 Ventilator formed to detail (gross weight measured) .............................................................................................................. 32.20 3.80 6.40 11.00 10046
COLLAPSIBLE GATES Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per kg $ $ $ $
10047 Mild steel collapsible gates, diamond pattern, welded and riveted connections..................................................................... 24.00 3.20 4.50 9.30 10047
10048 Ditto but galvanized.................................................................................................................................................................. 27.00 3.20 5.10 10.10 10048
10/24
10 STEEL AND METAL WORK 10
Item Item
SUNDRY REPAIRS Thickness of metal (mm)
N.e. 3 3-6 6 - 12 12 - 20
A B C D
Per linear metre $ $ $ $
10049 Straight, raking or circular cutting on any type of metal including filing edges clean............................................................ 2.10 2.70 4.80 7.60 10049
A
Each $
10050 Cut screw thread on end of steel or iron rod or tube for length upto twice the girth of the steel rod or tube
upto 50 mm in thread length........................................................................................................................................................................................................... 11.80 10050
10051 Add to Item 10050 for each additional 25 mm thread length or part thereof in length ................................................................................................................ 1.50 10051
10052 Cut off end of bolt or rod of upto 50 mm diameter for threading or re-threading......................................................................................................................... 4.20 10052
10053 Drill hole of upto 50 mm diameter in metal n.e. 50 mm deep including countersinking if required........................................................................................... 4.20 10053
10054 Add to Item 10053 for each additional 25 mm or part thereof in depth........................................................................................................................................ 0.80 10054
10055 Drill and tap hole in metal n.e. 50 mm deep.................................................................................................................................................................................. 6.80 10055
10056 Add to Item 10055 for each additional 25 mm or part thereof in depth........................................................................................................................................ 2.50 10056
Each
10057 Punch small hole for nail, screw and the like through any type of sheet metal not thicker than 3 mm........................................................................................ 0.80 10057
Execute the following welding including providing all plant, welding rods, etc., filing weld on completion and preparing and
chamfering ends, edges and surfaces to be welded as required : -
Per linear metre
10058 Fillet weld in lengths n.e. 300 mm at connections (net length of fillet measured - allowance made for angles, etc.)................................................................. 95.70 10058
10059 Fillet seam weld in lengths n.e. 300 mm at lapped joints (ditto)................................................................................................................................................... 79.80 10059
10060 Single butt weld in lengths exceeding 300 mm at butt joints and connections (net length of joint measured on one face only)................................................ 95.70 10060
10061 Double butt weld in lengths exceeding 300 mm when ordered at butt joints and connections where metal exceeds 6 mm thick
(net length of joint measured on both faces).................................................................................................................................................................................. 79.80 10061
Each
10062 Spot weld end of wire or rod n.e. 12 mm diameter, or bar n.e. 50 mm girth, and the like............................................................................................................ 4.80 10062
10/25
10 STEEL AND METAL WORK 10
Item Item
GALVANIZED MILD STEEL Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per kg $ $ $ $
10063 Round rods, square rods, flat bars, plates, chequer plates, angle sections, tee sections,
universal beams, columns, channels or "I" joists...................................................................................................................... 19.00 4.50 5.10 8.40 10063
10064 Rectangular, square or circular hollow sections excluding galvanized mild steel tubing....................................................... 20.00 4.50 5.10 8.40 10064
10065 Water bar................................................................................................................................................................................... 22.00 3.20 4.50 9.30 10065
10066 Wall tie, frame holdfast, single piece ceiling hanger or bracket, and the like......................................................................... 26.10 5.10 7.00 11.80 10066
10067 Composite ceiling hanger, bracket and the like of two or more pieces including
assembling, supplying and fixing nuts, bolts and washers, or welding................................................................................... 25.00 3.80 5.10 11.00 10067
10068 Chains, including hooks, rings, shackles, etc., complete......................................................................................................... 28.00 3.20 4.50 3.40 10068
10069 Flat / formed sheet covering...................................................................................................................................................... 25.00 3.20 4.50 9.30 10069
10070 Perforated flat or formed sheet covering................................................................................................................................... 19.00 3.20 4.50 9.30 10070
10071 Sheet lining to brick or concrete duct, sheet covering to roofs, domes, etc., including all rolls,
welts, flashings and the like, sheet as ducting, sheet as pipes, gutters, funnels, hoods, chimney
cowls, roof plates and the like, sheet in square or rectangular tanks, storage cisterns and the
like, and including angle stiffeners, corner plates and cover................................................................................................... 34.00 3.80 6.40 11.00 10071
10072 Ventilator formed to detail (gross weight measured)............................................................................................................... 37.00 3.80 6.40 10.60 10072
10073 Stopcock or meter box and the like with hinged or loose lid to detail (ironmongery measured separately)........................... 22.00 3.80 6.40 11.80 10073
A
Each $
10074 16 mm Diameter dowel 75 mm long including letting 40 mm in a frame, cutting mortice in concrete floor or paving if required, and
grouting in and making good.......................................................................................................................................................................................................... 8.80 10074
Diameter (mm)
40 50 65 75
Thickness (mm) 1.00 1.00 1.26 1.26
A B C D
Each $ $ $ $
10075 Single sided round toothed timber connector plate holed for bolt (measured separately) and fixing..................................... 6.50 6.80 7.20 7.40 10075
10076 Double sided ditto..................................................................................................................................................................... 9.20 9.50 9.90 10.30 10076
10/26
10 STEEL AND METAL WORK 10
Item Item
GALVANIZED STEEL WINDOWS AND GLAZED DOORS Take Take
Supply down down Fix
Galvanized steel windows and glazed doors (all glazing measured separately) : - and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10077 Galvanised steel window medium sections.............................................................................................................................. 656.80 24.20 25.50 47.30 10077
10078 Extra over for openable portions............................................................................................................................................... 345.40 - - - 10078
10079 Galvanised steel window large (38 mm) sections.................................................................................................................... 784.50 28.70 30.60 56.60 10079
10080 Extra over Item 10079 for openable portions........................................................................................................................... 410.30 - - - 10080
10081 Galvanised steel door medium sections.................................................................................................................................... 565.70 22.30 23.00 42.20 10081
10082 Extra over Item 10081 for openable portions........................................................................................................................... 293.10 - - - 10082
10083 Galvanised steel door large (38 mm) sections.......................................................................................................................... 673.00 26.10 27.40 50.70 10083
10084 Extra over Item 10083 for openable portions........................................................................................................................... 348.40 - - - 10084
REPAIRS TO GALVANIZED STEEL WINDOWS AND DOORS
A
Per linear metre $
10085 Coupling mullion for window complete with mastic for assembly............................................................................................................................................... 42.20 10085
10086 Coupling mullion for door or side light ditto................................................................................................................................................................................. 42.20 10086
10087 Coupling transom for window ditto................................................................................................................................................................................................ 44.80 10087
10088 Coupling transom for door or side light with ventilator over ditto................................................................................................................................................ 47.40 10088
Per square metre
10089 Take down and clear away openable sash, ventilator, window or door of any size or section including cutting
hinges away from frame.................................................................................................................................................................................................................. 10.10 10089
10090 Take down and set aside for re-use ditto........................................................................................................................................................................................ 8.30 10090
10091 Fix only openable sash, ventilator, window or door of any size or section to existing frame including welding or riveting hinges........................................... 17.20 10091
Each
10092 Oil only hinges and fittings to openable sash, ventilator, window or door................................................................................................................................... 3.20 10092
10093 Weld joint, corner, etc., of sash, ventilator, window, door or frame.............................................................................................................................................. 12.80 10093
10/27
10 STEEL AND METAL WORK 10
Item Item
REPAIRS TO GALVANIZED STEEL WINDOWS AND DOORS (CONT'D) Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per kg $ $ $ $
10094 Galvanized steel glazing bar of any diameters......................................................................................................................... 18.70 3.20 4.50 10.10 10094
10095 Galvanized steel channel bead fixed to existing window and door......................................................................................... 21.60 3.30 5.40 12.70 10095
Each
10096 Pair n.e. 75 mm butt hinges...................................................................................................................................................... 31.40 7.70 - 16.90 10096
10097 Pair projecting hinges (for metal casement)............................................................................................................................. 52.70 8.50 - 21.10 10097
10098 Barrel bolt n.e. 150 mm long with socket................................................................................................................................. 35.10 7.70 - 18.60 10098
10099 Ditto but 150 - 300 mm long ditto............................................................................................................................................ 54.80 7.70 - 19.40 10099
10100 Mortice lock with staple including labelling keys.................................................................................................................... 166.70 18.50 24.90 56.60 10100
10101 Set of lever handle furniture...................................................................................................................................................... 103.70 6.40 7.70 16.90 10101
10102 75 mm Cleat hook..................................................................................................................................................................... 14.60 1.90 - 4.20 10102
10103 Spring catch with ring and staple.............................................................................................................................................. 36.00 3.20 4.50 7.60 10103
10104 Staple only................................................................................................................................................................................. 14.50 1.30 - 3.40 10104
10105 Screw eye................................................................................................................................................................................... 9.00 1.30 - 2.50 10105
10106 Casement fastener with 115 mm handle and two point nose................................................................................................... 37.80 3.20 3.80 16.90 10106
10107 Two throw casement fastener with 115 mm handle and steel connecting rod........................................................................ 99.50 6.40 7.70 33.80 10107
10108 Casement stay of sliding bar type n.e. 300 mm long................................................................................................................ 53.30 4.50 5.70 10.10 10108
10109 Casement stay with two stud pins n.e. 300 mm long............................................................................................................... 29.00 4.50 5.10 9.30 10109
10110 Single stud pin only................................................................................................................................................................... 7.80 1.30 - 2.50 10110
10111 Set of sliding shoes, pivots and friction side arms for projecting casement............................................................................ 94.90 4.50 5.10 10.10 10111
10112 Pair fanlight roller stays............................................................................................................................................................ 44.30 2.60 3.20 4.20 10112
10113 Through-the-frame type fanlight stay........................................................................................................................................ 113.90 1.90 1.90 3.40 10113
10114 Roto-operator opening and closing mechanism with handle................................................................................................... 132.90 1.90 2.60 4.20 10114
10115 Fanlight opener with 300 mm rack and pinion, worm wheel, pulley and endless cord.......................................................... 165.00 12.80 15.30 22.80 10115
10116 Ditto but with 375 mm long rack and pinion............................................................................................................................ 170.00 13.40 16.00 23.60 10116
10/28
10 STEEL AND METAL WORK 10
Item Item
GALVANIZED STEEL SHEET CLADDING Take Take
(FACE WORK OTHER THAN ROOFING) Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10117 Corrugated steel sheet cladding n.e. 0.60 mm thick in any corrugation and colour 73.90 4.50 11.50 20.30 10117
fixed to timber framing (measured separately).........................................................................................................................
10118 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 77.90 4.50 12.10 21.10 10118
10119 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 89.60 5.10 12.80 23.60 10119
10120 Corrugated steel sheet cladding n.e. 0.60 mm thick in any corrugation and colour
fixed to curved timber framing (measured separately)............................................................................................................. 76.90 5.10 12.80 22.00 10120
10121 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 80.30 5.10 13.40 22.80 10121
10122 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 92.10 5.70 14.00 24.50 10122
10123 Corrugated steel sheet cladding n.e. 0.60 mm thick in any corrugation and colour 75.20 4.50 11.50 24.50 10123
fixed to steel framing (measured separately)............................................................................................................................
10124 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 78.50 4.50 12.10 25.30 10124
10125 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 90.10 5.10 12.80 27.00 10125
10126 Corrugated steel sheet cladding n.e. 0.60 mm thick in any corrugation and colour
fixed to curved steel framing (measured separately)................................................................................................................ 77.60 5.10 12.80 27.00 10126
10127 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 78.50 5.10 13.40 28.70 10127
10128 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 90.20 5.70 14.00 29.60 10128
Per linear metre
10129 Drip or flashing n.e. 0.60 mm thick and up to 150 mm girth fixed over door or window head,
lapped 150 mm at end laps (measured net).............................................................................................................................. 15.50 1.30 3.20 5.90 10129
10130 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 16.90 1.30 3.20 5.90 10130
10131 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 19.60 1.90 3.80 6.80 10131
10/29
10 STEEL AND METAL WORK 10
Item Item
PROPRIETARY PROFILED STEEL SHEET CLADDING
(FACE WORK OTHER THAN ROOFING)
Proprietary profiled steel sheet cladding, trapezoidal ribbed, roll-formed walling profile; has bold, Take Take
widely spaced ribs and is formed from steel; minimum base metal thickness is 0.42 mm (BMT), Supply down down Fix
grade of steel G550 (550 N/mm yield strength); coating class AZ150, total coated thickness in 0.47 and and and set only
mm (TCT); and available in a range of steel paint systems and colours : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10132 0.47 mm Thick proprietary profiled steel sheeting fixed to timber framing............................................................................ 344.80 3.80 8.30 16.10 10132
10133 Ditto but fixed to curved timber framing.................................................................................................................................. 350.10 4.50 8.90 17.70 10133
10134 0.47 mm Thick proprietary profiled steel sheeting fixed to steel framing............................................................................... 347.30 3.80 8.90 16.10 10134
10135 Ditto but fixed to curved steel framing..................................................................................................................................... 350.80 4.50 9.60 18.60 10135
Proprietary profiled steel sheet cladding, roll-formed from steel, lock-action rib for positive
concealed clip fixing; profile with an effective cover width of 406 mm and a rib height of 41
mm; minimum base metal thickness is 0.48 mm (BMT), grade of steel G550 (550 N/mm yield
strength); coating class AZ150, total coated thickness in 0.53 mm (TCT); and available in a
range of steel paint systems and colours : -
Per square metre
10136 0.53 mm Thick proprietary profiled steel sheet cladding fixed to timber framing.................................................................. 416.50 3.80 8.30 16.90 10136
10137 Ditto but 0.65 mm thick............................................................................................................................................................ 468.10 4.50 8.90 17.70 10137
10138 0.53 mm Thick proprietary profiled steel sheet cladding fixed to curved timber framing...................................................... 420.00 4.50 9.60 17.70 10138
10139 Ditto but 0.65 mm thick............................................................................................................................................................ 472.10 4.50 10.20 19.40 10139
10140 0.53 mm Thick proprietary profiled steel sheet cladding fixed to steel framing..................................................................... 417.40 4.50 8.90 16.90 10140
10141 Ditto but 0.65 mm thick............................................................................................................................................................ 469.20 4.50 9.60 17.70 10141
10142 0.53 mm Thick proprietary profiled steel sheet cladding fixed to curved steel framing......................................................... 421.30 4.50 10.20 18.60 10142
10143 Ditto but 0.65 mm thick............................................................................................................................................................ 473.00 4.50 10.20 19.40 10143
A
Each $
10144 Cut hole through existing sheet cladding for pipes or articles in any size and thickness............................................................................................................. 17.10 10144
10/30
10 STEEL AND METAL WORK 10
Item Item
GALVANIZED MILD STEEL TUBING Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per linear metre $ $ $ $
10145 15 mm Bore medium series galvanized tubing......................................................................................................................... 27.50 1.90 2.60 6.80 10145
10146 20 mm Ditto............................................................................................................................................................................... 35.80 2.60 3.20 8.50 10146
10147 25 mm Ditto............................................................................................................................................................................... 50.40 3.20 3.80 11.00 10147
10148 32 mm Ditto............................................................................................................................................................................... 63.50 3.80 4.50 13.50 10148
10149 40 mm Ditto............................................................................................................................................................................... 74.80 5.10 5.70 17.70 10149
10150 50 mm Ditto............................................................................................................................................................................... 109.20 7.00 8.90 22.80 10150
10151 80 mm Ditto............................................................................................................................................................................... 182.20 9.60 11.50 29.60 10151
10152 100 mm Ditto............................................................................................................................................................................. 238.10 10.90 13.40 33.80 10152
10153 150 mm Ditto............................................................................................................................................................................. 348.90 12.80 15.30 39.70 10153
Add to either of Items 10145 to 10153 inclusive for bending to radius n.e. 15.00 m............................................................. 5% - - -
GALVANIZED STEEL WIRE ROPE, ETC.
Per linear metre
10154 3 mm Diameter flexible galvanized steel wire rope in flagstaff guys and the like including all binding
and splicing, and splicing to existing rope............................................................................................................................... 9.50 1.30 1.90 3.40 10154
10155 4 mm Ditto................................................................................................................................................................................. 9.80 1.30 1.90 3.40 10155
10156 6 mm Ditto................................................................................................................................................................................. 10.70 1.30 1.90 3.40 10156
10157 8 mm Ditto................................................................................................................................................................................. 11.50 1.90 1.90 4.20 10157
10158 10 mm Ditto............................................................................................................................................................................... 12.10 1.90 1.90 4.20 10158
Each
10159 Galvanized steel sail thimble for rope n.e. 6 mm diameter...................................................................................................... 6.30 - - - 10159
10160 Ditto but exceeding 6 mm and n.e. 10 mm diameter................................................................................................................ 7.00 - - - 10160
10161 Galvanized wrot iron "D" shaped shackle with 6 mm diameter metal rod or bolt at centre of bow....................................... 13.90 1.30 1.90 4.20 10161
10162 Ditto but with 8 mm diameter metal rod or bolt at centre of bow............................................................................................ 16.50 1.30 1.90 4.20 10162
10163 Ditto but with 10 mm diameter metal rod or bolt at centre of bow.......................................................................................... 16.50 1.90 1.90 4.20 10163
10164 Heavy duty galvanized steel rope strainer with central body, screw hook on one end and screw eye
on the other end, 375 mm long overall to take load of 1 tonne................................................................................................ 40.10 3.80 4.50 8.50 10164
10165 Ditto but 475 mm long overall to take load of 2 tonnes........................................................................................................... 69.50 6.40 7.70 11.00 10165
10/31
10 STEEL AND METAL WORK 10
Item Item
REPAIRS TO GRATES, RANGES, ETC. Take
down Fix
and only
clear
away
A B
Each $ $
10166 Oven or side boiler ....................................................................................................................................................................................................... 55.50 171.40 10166
10167 Set of front bars, bottom grating, pair of iron fire cheeks, oven door, damper rod, soot door, smoke box,
register plane, falling door, etc. .................................................................................................................................................................................... 7.00 21.10 10167
STAINLESS STEEL
SHEET METAL WORK Take Take
Supply and fix down down Fix
and and set only
AISI AISI clear aside for
304 316 away re-use
A B C D E
Per kg $ $ $ $ $
10168 Chequer plate........................................................................................................................................................... 74.90 - 6.40 7.00 16.10 10168
10169 Flat or formed sheet covering.................................................................................................................................. 67.90 78.70 7.00 8.30 13.50 10169
10170 Perforated flat or formed sheet covering................................................................................................................. 50.30 58.30 5.70 8.30 13.50 10170
10171 Sheet as pipes, gutters, funnels, hoods, chimney cowls, roof plates and the like.................................................. 84.40 117.40 8.30 10.20 20.30 10171
10172 Ventilator formed to detail (gross weight measured)............................................................................................. 79.40 110.40 8.30 8.90 16.90 10172
METAL SECTIONS
Supply and fix
Fix
AISI AISI only
304 316
A B C
Per kg $ $ $
10173 Round rods, square rods, flat bars, plates, angle sections, tees, channels and other similar sections....................................................... 71.70 77.80 13.50 10173
10174 Rectangular, square or circular hollow sections ........................................................................................................................................ 81.70 82.00 14.40 10174
Per square metre
10175 Add to either of Items 10168 to 10174 inclusive for Finish No. 4 - polished with fine grit or hair line finish........................................ 6.20 10.30 - 10175
10176 Add to either of Items 10168 to 10174 inclusive for Finish No. 8 - mirror finish.................................................................................... 15.50 25.90 - 10176
(Note : - The above Items 10168 to 10174 inclusive for stainless steel in grade AISI 316 will only be paid for, if ordered
by the Maintenance Surveyor in writing.)
A
Per kg $
10177 Take down and clear away any of the above sections (Items 10168 to 10174 inclusive)............................................................................................................. 4.50 10177
10178 Take down and set aside for re-use (ditto)...................................................................................................................................................................................... 5.70 10178
10/32
10 STEEL AND METAL WORK 10
Item Item
STAINLESS STEEL (CONT'D)
METAL SECTIONS (CONT'D) Take Take
Supply and fix down down Fix
and and set only
AISI AISI clear aside for
304 316 away re-use
A B C D E
Each $ $ $ $ $
10179 Flange plate to 25 mm diameter tubing.................................................................................................................. 21.30 32.00 1.30 1.90 4.20 10179
10180 Ditto but to 38 mm diameter tubing........................................................................................................................ 28.70 43.10 1.90 2.60 5.10 10180
10181 Ditto but to 50 mm diameter tubing........................................................................................................................ 34.70 52.10 1.90 2.60 5.90 10181
10182 Ditto but to 75 mm diameter tubing........................................................................................................................ 44.10 66.20 2.60 3.20 6.80 10182
10183 Add to either of Items 10179 to 10182 inclusive for Finish No. 4 - polished with fine grit
or hair line finish .................................................................................................................................................... 3.00 4.80 - - - 10183
10184 Add to either of Items 10179 to 10182 inclusive for Finish No. 8 - mirror finish................................................. 7.50 11.10 - - - 10184
(Note : - The above Items 10179 to 10182 inclusive for stainless steel in grade AISI 316 will only be
paid for, if ordered by the Maintenance Surveyor in writing)
BOLTS AND ANCHOR BOLTS FOR ISOLATED REPAIRS
(Note : Items 10185 to 10191 inclusive shall only be measured when they are required for replacement Supply and fix
in isolated repair items as stipulated in Special Conditions Clauses SC10.11 and SC10.39.) Stainless Mild
steel steel
AISI 304
A B
Per kg $ $
10185 Bolt with nut and washer.............................................................................................................................................................................................. 56.60 17.40 10185
Nominal diameter of shank (mm)
6 8 10 12 16 20
A B C D E F
Each $ $ $ $ $ $
10186 Steel ragbolt n.e 150 mm long overall.................................................................................................. 6.80 8.40 10.00 11.50 14.40 18.70 10186
10187 Ditto but 150 - 300 mm long overall..................................................................................................... 7.30 9.10 10.80 12.00 15.20 19.70 10187
10188 Steel ragbolt (loose bolt or bolt projecting type) n.e. 150 mm long overall......................................... 5.80 7.10 8.50 12.30 23.70 34.80 10188
10189 Ditto but 150 - 300 mm long overall..................................................................................................... 8.30 10.20 12.10 15.00 25.90 42.60 10189
10190 Non-drilling or self drilling anchor bolt of any length......................................................................... 5.70 6.40 7.80 9.20 13.10 17.90 10190
10191 Stud anchor bolt of any length.............................................................................................................. 7.00 7.20 7.70 10.30 16.10 25.70 10191
10/33
10 STEEL AND METAL WORK 10
Item Item
ALUMINIUM SHEET CLADDING Take Take
(FACE WORK OTHER THAN ROOFING) Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10192 Corrugated aluminium sheet cladding n.e. 0.60 mm thick in any corrugation and colour
fixed to timber framing (measured separately)......................................................................................................................... 313.30 4.20 8.50 15.20 10192
10193 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 374.40 4.50 8.90 17.70 10193
10194 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 473.70 5.10 9.60 19.40 10194
10195 Corrugated aluminium sheet cladding n.e. 0.60 mm thick in any corrugation and colour
fixed to curved timber framing (measured separately)............................................................................................................. 317.70 5.10 9.60 19.40 10195
10196 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 376.10 5.10 9.60 20.30 10196
10197 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 475.20 5.10 10.20 22.00 10197
10198 Corrugated aluminium sheet cladding n.e. 0.60 mm thick in any corrugation and colour
fixed to steel framing (measured separately)............................................................................................................................ 316.50 4.50 8.90 17.70 10198
10199 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 374.80 5.10 9.60 18.60 10199
10200 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 474.00 5.10 9.60 20.30 10200
10201 Corrugated aluminium sheet cladding n.e. 0.60 mm thick in any corrugation and colour
fixed to curved steel framing (measured separately)................................................................................................................ 318.20 5.10 9.60 20.30 10201
10202 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 376.50 5.10 10.20 21.10 10202
10203 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 475.70 5.70 10.90 22.80 10203
Per linear metre
10204 Drip or flashing n.e. 0.60 mm and up to 150 mm girth fixed over door or window head,
lapped 150 mm at end laps (measured net).............................................................................................................................. 33.40 1.30 3.20 5.90 10204
10205 Ditto but 0.60 - 0.80 mm thick.................................................................................................................................................. 38.40 1.90 3.20 5.90 10205
10206 Ditto but 0.80 - 1.00 mm thick.................................................................................................................................................. 48.00 1.90 3.20 6.80 10206
10/34
10 STEEL AND METAL WORK 10
Item Item
ALUMINIUM
Take Take
SHEET METAL WORK Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per kg $ $ $ $
10207 Chequer plate............................................................................................................................................................................. 49.60 5.70 7.00 16.90 10207
10208 Flat or formed sheet covering.................................................................................................................................................... 51.80 5.70 7.70 15.20 10208
10209 Perforated flat or formed sheet covering................................................................................................................................... 38.40 5.70 7.70 15.20 10209
10210 Sheet as pipes, gutters, funnels, hoods, chimney cowls, roof plates and the like.................................................................... 60.00 8.90 11.50 27.90 10210
10211 Ventilator formed to detail (gross weight measured)............................................................................................................... 64.00 7.70 9.60 22.80 10211
10212 Round rods, square rods, flat bars, plates, angle sections, tees, channels or similar sections................................................. 71.70 5.70 7.70 38.90 10212
10213 Rectangular, square or circular hollow sections....................................................................................................................... 71.40 5.70 7.70 39.70 10213
10214 Segmental or moulded edge trim in any thickness................................................................................................................... 52.60 7.70 9.60 19.40 10214
Add to either of Items 10207 to 10214 inclusive for bronze or black anodized finish in lieu of clear anodized finish.............................................................. 5%
Add to either of Items 10207 to 10214 inclusive for powder coated or fluorocarbon coated finish in lieu of clear anodized finish.......................................... 12%
ALUMINIUM WINDOWS AND GLAZED DOORS Take Take
Supply down down Fix
Aluminium windows and glazed doors (all glazing measured separately) : - and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10215 Aluminium window in clear anodized finish .......................................................................................................................... 1,384.80 19.10 19.80 50.70 10215
10216 Extra over ditto for openable portions...................................................................................................................................... 249.30 - - - 10216
10217 Aluminium door in clear anodized finish................................................................................................................................. 1,273.50 17.20 17.90 44.80 10217
10218 Extra over ditto for openable portions...................................................................................................................................... 202.80 - - - 10218
Add to either of Items 10215 to 10218 inclusive for bronze or black anodized finish in lieu of clear anodized finish.............................................................. 5%
Add to either of Items 10215 to 10218 inclusive for powder coated or fluorocarbon coated finish in lieu of clear anodized finish.......................................... 12%
10/35
10 STEEL AND METAL WORK 10
Item Item
REPAIRS TO ALUMINIUM WINDOWS AND DOORS
A
Per linear metre $
10219 Coupling mullion for window complete with mastic for assembly............................................................................................................................................... 42.20 10219
10220 Coupling mullion for door or side light ditto................................................................................................................................................................................. 42.20 10220
10221 Coupling transom for window ditto................................................................................................................................................................................................ 44.80 10221
10222 Coupling transom for door or side light with ventilator over ditto................................................................................................................................................ 47.40 10222
10223 Positive pressure neoprene gasket seal........................................................................................................................................................................................... 8.30 10223
10224 Neoprene wiping primary seal........................................................................................................................................................................................................ 12.86 10224
10225 Glazing gasket for fixing................................................................................................................................................................................................................. 6.30 10225
Per square metre
10226 Take down and clear away openable sash, ventilator, window or door of any size or section including cutting hinges away from frame................................ 10.10 10226
10227 Take down and set aside for re-use ditto........................................................................................................................................................................................ 8.30 10227
10228 Fix only openable sash, ventilator, window or door of any size or section to existing frame including welding or riveting hinges........................................... 17.20 10228
Each
10229 Oil only hinges and fittings to openable sash, ventilator, window or door................................................................................................................................... 3.20 10229
10230 Weld joint, corner, etc., of sash, ventilator, window, door or frame.............................................................................................................................................. 12.80 10230
Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per linear metre $ $ $ $
10231 Aluminum glazing bar of any diameters................................................................................................................................... 18.70 3.20 4.50 10.10 10231
10232 Aluminum channel bead fixed to existing window and door................................................................................................... 21.60 3.30 5.40 12.70 10232
Add to either of Items 10231 to 10232 inclusive for bronze or black anodized finish in lieu of clear anodized finish.............................................................. 5%
Add to either of Items 10231 to 10232 inclusive for powder coated or fluorocarbon coated finish in lieu of clear anodized finish......................................... 12%
10/36
10 STEEL AND METAL WORK 10
Item Item
REPAIRS TO ALUMINIUM WINDOWS AND DOORS (CONT'D) Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Each $ $ $ $
10233 Pair of butt hinges n.e. 75 mm long.......................................................................................................................................... 31.40 7.00 8.90 10.10 10233
10234 Pair of locally manufactured sliding shoes 200 to 400mm long, pivots and friction side arm for
projecting window..................................................................................................................................................................... 147.00 21.70 26.80 31.30 10234
10235 Ditto but 400 - 600 mm ........................................................................................................................................................... 250.50 37.00 45.90 51.50 10235
10236 Pair of patent sliding shoes 200 to 400 mm long, pivots and friction side arms for projecting windows.............................. 242.30 17.20 21.10 31.30 10236
10237 Ditto but 400 - 600 mm long..................................................................................................................................................... 412.70 29.30 36.40 51.50 10237
10238 Barrel bolt n.e. 150 mm long.................................................................................................................................................... 35.10 5.70 7.70 11.00 10238
10239 Ditto but 150 - 300 mm long..................................................................................................................................................... 54.80 5.70 7.70 11.80 10239
10240 Flush bolt n.e. 150 mm long ..................................................................................................................................................... 48.50 5.70 7.00 11.80 10240
10241 Ditto but 150 - 300 mm long..................................................................................................................................................... 63.00 5.70 7.70 11.00 10241
10242 Cam catch.................................................................................................................................................................................. 41.10 2.60 3.20 7.60 10242
10243 Mortice lock with brass dead bolt and spring bolt, striking plate and four lever mechanism including
labelling keys............................................................................................................................................................................. 130.60 18.50 24.20 57.40 10243
10244 Set of lever handle furniture...................................................................................................................................................... 82.70 5.10 7.00 17.70 10244
10245 Mortice lock with brass expanding claw bolt for sliding door and flush furniture................................................................. 145.70 17.90 23.60 57.40 10245
10246 Casement fastener with 115 mm handle and standard wedge plate........................................................................................ 37.80 7.00 8.90 17.70 10246
10247 Two throw ditto with steel connecting rod............................................................................................................................... 79.30 14.00 17.90 34.60 10247
10248 Through-the-frame type casement fastener............................................................................................................................... 53.60 9.60 12.10 22.80 10248
10249 Two throw ditto with steel connecting rod............................................................................................................................... 116.60 14.00 18.50 34.60 10249
10250 Casement stay of sliding bar type n.e. 300 mm long................................................................................................................ 53.40 4.50 5.10 10.10 10250
10251 Casement stay with two stud pins n.e. 300 mm long............................................................................................................... 31.60 5.10 5.70 10.10 10251
10252 Set of adjustable rollers to suit sliding windows including all necessary guide, etc............................................................... 96.50 12.10 16.60 39.70 10252
10253 Ditto but for sliding door........................................................................................................................................................... 116.40 12.10 17.20 41.40 10253
10254 100 mm Pull handle.................................................................................................................................................................. 26.00 3.20 3.80 6.80 10254
10255 100 mm Flush pull handle......................................................................................................................................................... 39.90 3.20 3.80 7.60 10255
10/37
10 STEEL AND METAL WORK 10
Item Item
BRASS Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per kg $ $ $ $
10256 Casting, trimmed from mould, rough filed, drilled and countersunk as required.................................................................... 81.60 4.50 5.10 11.00 10256
10257 Ditto but fine filed, buffed and polished, drilled and countersunk, turned, threaded and
brazed as required ..................................................................................................................................................................... 92.10 4.50 5.10 11.00 10257
10258 Strip set in screed or paving as dividing strip........................................................................................................................... 89.60 4.50 5.10 9.30 10258
10259 Ditto but bent in addition at expansion joints........................................................................................................................... 106.40 4.50 5.10 10.10 10259
10260 Flat or formed sheet covering.................................................................................................................................................... 92.60 4.50 5.10 9.30 10260
10261 Sheet covering to roofs, domes, etc., including all rolls, welts, flashings and the like, sheet as pipes,
gutters, hoods, chimney cowls, roof plates and the like and sheet as square or rectangular tanks,
storage cisterns, etc., including all stiffeners, corner plates and covers................................................................................... 108.30 9.60 12.10 23.60 10261
10262 Ventilator formed to detail (gross weight measured)............................................................................................................... 105.30 8.90 11.50 21.10 10262
COPPER Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per kg $ $ $ $
10263 Casting, trimmed from mould, rough filed, drilled and countersunk as required, including
making pattern and preparing mould ....................................................................................................................................... 110.00 4.50 5.10 11.00 10263
10264 Ditto but fine filed, buffed and polished, drilled and countersunk, turned, threaded and
brazed as required ..................................................................................................................................................................... 114.00 4.50 5.10 11.00 10264
10265 Flat or formed sheet covering.................................................................................................................................................... 125.70 4.50 5.10 9.30 10265
10266 Sheet covering to roofs, domes, etc., including all rolls, welts, flashings and the like, sheet as pipes,
gutters, hoods, chimney cowls, roof plates and the like and sheet as square or rectangular tanks,
storage cisterns, etc., including all stiffeners, corner plates and covers................................................................................... 141.50 9.60 12.10 24.50 10266
10267 Ventilator formed to detail (gross weight measured)............................................................................................................... 137.50 8.90 11.50 22.00 10267
10/38
10 STEEL AND METAL WORK 10
Item Item
ROLLER SHUTTERS Take Take
Supply down down Fix
Supply and fix manually operated roller shutters to suit any structural opening by an approved and and and set only
roller shutter manufacturer : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10268 Galvanised mild steel rolling shutter Type K2 or B2............................................................................................................... 1,243.00 158.80 204.10 401.10 10268
10269 Extra over for wicket door......................................................................................................................................................... 1,244.60 - - - 10269
10270 Stainless steel rolling shutter, Finish No. 4 - polished with fine grit or hair line finish.......................................................... 2,527.40 158.80 204.10 401.10 10270
10271 Extra over for wicket door......................................................................................................................................................... 1,876.50 - - - 10271
10272 Stainless steel rolling shutter, Finish No. 8 - mirror finish...................................................................................................... 2,895.10 158.80 204.10 401.10 10272
10273 Extra over for wicket door......................................................................................................................................................... 2,144.70 - - - 10273
10274 Stainless steel link grilles shutters Type 12F............................................................................................................................ 2,136.90 158.80 204.10 401.10 10274
10275 Stainless steel semi-grilles shutters, Finish No. 4 - polished with fine grit or hair line finish................................................ 2,343.60 158.80 204.10 401.10 10275
10276 Ditto but Finish No. 8 - mirror finish........................................................................................................................................ 2,692.10 158.80 204.10 401.10 10276
10277 Aluminium rolling shutters Type OEC2 or EK2, clear anodized............................................................................................ 1,348.00 158.80 204.10 401.10 10277
10278 Extra over for wicket door......................................................................................................................................................... 2,527.40 - - - 10278
10279 Aluminium rolling shutters Type OEC2 or EK2, bronze anodized......................................................................................... 1,470.50 158.80 204.10 401.10 10279
10280 Extra over for wicket door......................................................................................................................................................... 2,697.00 - - - 10280
10281 Aluminium link grilles shutters Type 12F................................................................................................................................ 1,455.20 158.80 204.10 401.10 10281
10282 Aluminium semi-grilles shutters, clear anodized..................................................................................................................... 1,629.50 158.80 204.10 401.10 10282
10283 Ditto but bronze anodized......................................................................................................................................................... 1,723.30 158.80 204.10 401.10 10283
10/39
10 STEEL AND METAL WORK 10
Item Item
ROLLER SHUTTERS (CONT'D)
Take Take
Supply and fix electrically operated roller shutters to suit any opening by an approved roller shutter Supply down down Fix
manufacturer including provision of connection to nearest power point by a registered electrical and and and set only
worker : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10284 Galvanised mild steel rolling shutter Type K2 or B2............................................................................................................... 1,563.40 197.70 255.10 506.70 10284
10285 Extra over for wicket door......................................................................................................................................................... 1,244.60 - - - 10285
10286 Stainless steel rolling shutter, Finish No. 4 - polished with fine grit or hair line finish.......................................................... 4,184.20 197.70 255.10 506.70 10286
10287 Extra over for wicket door......................................................................................................................................................... 1,876.50 - - - 10287
10288 Stainless steel rolling shutter, Finish No. 8 - mirror finish...................................................................................................... 4,412.70 197.70 255.10 506.70 10288
10289 Extra over for wicket door......................................................................................................................................................... 2,113.90 - - - 10289
10290 Stainless steel link grilles shutters Type 12F............................................................................................................................ 3,540.20 197.70 255.10 506.70 10290
10291 Stainless steel semi-grilles shutters, Finish No. 4 - polished with fine grit or hair line finish................................................ 3,764.00 197.70 255.10 506.70 10291
10292 Ditto but Finish No. 8 - mirror finish........................................................................................................................................ 4,092.90 197.70 255.10 506.70 10292
10293 Aluminium rolling shutters Type OEC2 or EK2, clear anodized............................................................................................ 1,970.20 197.70 255.10 506.70 10293
10294 Extra over for wicket door......................................................................................................................................................... 2,466.20 - - - 10294
10295 Aluminium rolling shutters Type OEC2 or EK2, bronze anodized......................................................................................... 2,103.00 197.70 255.10 506.70 10295
10296 Extra over for wicket door......................................................................................................................................................... 2,691.30 - - - 10296
10297 Aluminium link grilles shutters Type 12F................................................................................................................................ 2,090.90 197.70 255.10 506.70 10297
10298 Aluminium semi-grilles shutters, clear anodized..................................................................................................................... 2,251.70 197.70 255.10 506.70 10298
10299 Ditto but bronze anodized......................................................................................................................................................... 2,439.40 197.70 255.10 506.70 10299
TRANSPARENT SHUTTERS
Supply and fix transparent security roller shutter manually operated constructed with UV-resistant Take Take
and top grade polycarbonate panels, aluminium extruded frame and support in powder coated Supply down down Fix
finish, complete with housing, track mechanism and accessories, by an approved roller shutter and and and set only
manufacturer : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10300 Transparent security roller shutter............................................................................................................................................ 2,131.20 210.50 293.40 481.30 10300
10301 Extra over for wicket door......................................................................................................................................................... 2,680.60 - - - 10301
10/40
10 STEEL AND METAL WORK 10
Item Item
SUNDRIES FOR SHUTTERS Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per linear metre $ $ $ $
10302 Shutter hood, galvanized mild steel including access door and all necessary ironmongery................................................... 686.40 210.50 293.40 472.90 10302
10303 Ditto but stainless steel, hair line finish.................................................................................................................................... 1,914.70 210.50 293.40 472.90 10303
10304 Ditto but stainless steel, mirror face finish............................................................................................................................... 2,190.50 210.50 293.40 472.90 10304
10305 Ditto but aluminium, clear anodized......................................................................................................................................... 1,523.40 210.50 293.40 472.90 10305
10306 Ditto but aluminium, bronze anodized..................................................................................................................................... 1,644.50 210.50 293.40 472.90 10306
10307 Typhoon shutter guide with locking device.............................................................................................................................. 367.60 42.70 59.30 95.40 10307
Replacement parts only : -
Per set
10308 Lock and malleable iron shoot bolts......................................................................................................................................... 257.40 12.10 14.70 35.50 10308
10309 Coil spring with barrel, shutter n.e. 2.4 m width...................................................................................................................... 1,348.00 36.40 46.80 58.30 10309
10310 Add to Item 10309 for each additional 600 mm width of shutter or part thereof in width..................................................... 360.90 8.90 11.50 14.40 10310
10311 A pair of aluminium guide rail, shutter n.e. 2.4 m height........................................................................................................ 1,348.00 42.70 59.30 95.40 10311
10312 Add to Item 10311 for each additional 600 mm height of shutter or part thereof in height................................................... 360.00 10.90 14.70 23.60 10312
10313 A pair of stainless steel guide rail, shutter n.e. 2.4 m height.................................................................................................... 2,998.50 42.70 59.30 95.40 10313
10314 Add to Item 10313 for each additional 600 mm height of shutter or part thereof in height................................................... 749.60 10.90 14.70 23.60 10314
10315 A pair of galvanized mild steel guide rail, shutter n.e. 2.4 m height....................................................................................... 833.30 42.70 59.30 95.40 10315
10316 Add to Item 10315 for each additional 600 mm height of shutter or part thereof in height................................................... 202.20 10.90 14.70 23.60 10316
Per square metre
10317 Slat for galvanised mild steel rolling shutter Type K2 or B2................................................................................................... 440.40 102.10 133.90 266.00 10317
10318 Slat for stainless steel rolling shutter, Finish No. 4 - polished with fine grit or hair line finish.............................................. 612.70 102.10 133.90 266.00 10318
10319 Slat for stainless steel rolling shutter, Finish No. 8 - mirror finish.......................................................................................... 737.60 102.10 133.90 266.00 10319
10320 Slat for stainless steel link grilles shutters Type 12F............................................................................................................... 727.60 102.10 133.90 266.00 10320
10321 Slat for stainless steel semi-grilles shutters, Finish No. 4 - polished with fine grit or hair line finish.................................... 765.90 102.10 133.90 266.00 10321
10322 Ditto but Finish No. 8 - mirror finish........................................................................................................................................ 896.10 102.10 133.90 266.00 10322
10323 Slat for aluminium rolling shutters Type OEC2 or EK2, clear anodized................................................................................ 593.60 102.10 133.90 266.00 10323
10324 Slat for aluminium rolling shutters Type OEC2 or EK2, bronze anodized............................................................................. 627.60 102.10 133.90 266.00 10324
10/41
10 STEEL AND METAL WORK 10
Item Item
SUNDRIES FOR SHUTTERS (CONT'D) Take Take
Supply down down Fix
Replacement parts only : - (Cont'd) and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10325 Slat for aluminium link grilles shutters Type 12F.................................................................................................................... 661.90 102.10 133.90 266.00 10325
10326 Slat for aluminium semi-grilles shutters, clear anodized......................................................................................................... 689.30 102.10 133.90 266.00 10326
10327 Ditto but bronze anodized......................................................................................................................................................... 728.60 102.10 133.90 266.00 10327
METAL LOUVRE FRAMES
Metal adjustable louvre frames complete with clips, operating handle, etc., and all necessary mullion coupling clips and Supply and fix
spacers for 100, 150 or 225 mm glass blades (measured separately), including any assembling, screwing to wood, plugging Galvan-
and screwing to concrete, brick, stone or other jamb or coupled to form mullion, and bedding with and including providing ized steel
mastic in accordance with the manufacturer's instructions : - with
alumin- Plain or
Set of two metal adjustable louvre frames complete with clips for glass, operating handle, etc., and any necessary mullion ium anodized
coupling clips and spacers : - lacquer alumin-
or stove ium
baked
enamel
finish
A B
Per set $ $
10328 Set of two frames with clips for three 100 mm wide glass blades (285 mm overall height)...................................................................................... 163.60 223.90 10328
10329 Add to Item 10328 for each additional clip (each additional 90 mm in overall height) or part thereof in height...................................................... 31.20 50.20 10329
10330 Set of two frames with clips for two 150 mm wide glass blades (300 mm overall height)........................................................................................ 179.20 245.00 10330
10331 Add to Item 10330 for each additional clip (each additional 140 mm in overall height) or part thereof in height.................................................... 54.60 86.00 10331
10332 Set of two frames with clips for two 225 mm wide glass blades (440 mm overall height)........................................................................................ 226.70 341.50 10332
10333 Add to Item 10332 for each additional clip (each additional 200 mm in overall height) or part thereof in height.................................................... 75.10 128.80 10333
Per linear metre
10334 Top weather strip to louvres.......................................................................................................................................................................................... 73.70 99.30 10334
10335 Bottom ditto................................................................................................................................................................................................................... 76.80 99.30 10335
Take Take
down down Fix
and and set only
clear aside for
away re-use
A B C
Per linear metre $ $ $
10336 Set of two frames with clips as above described (net height of each set of two frames measured).......................................................... 12.80 26.20 63.30 10336
10337 Top or bottom weather strip........................................................................................................................................................................ 3.20 5.70 14.40 10337
10/42
10 STEEL AND METAL WORK 10
Item Item
SLOTTED ANGLES
Take Take
Slotted steel angle, rust protected and stove enamelled, fixed complete and including all cutting, Supply down down Fix
fitting, supplying and fixing screws, bolts, nuts, washers, corner stiffeners and rubber pads, and and and set only
plugging to concrete, brick, stone or other surfaces and making good : - fix clear aside for
away re-use
A B C D
Per linear metre $ $ $ $
10338 36 x 36 x 1.80 mm Slotted angle section in brackets, shelving racks, stands and the like..................................................... 38.40 3.80 7.70 18.60 10338
10339 40 x 40 x 2.00 mm Ditto........................................................................................................................................................... 42.40 3.80 7.70 18.60 10339
10340 62 x 41 x 2.00 mm Ditto........................................................................................................................................................... 44.50 3.80 7.70 18.60 10340
10341 66 x 45 x 2.50 mm Ditto........................................................................................................................................................... 53.10 3.80 7.70 18.60 10341
STEEL NETTING, MESH AND EXPANDED METAL Take Take
Supply and fix down down Fix
and and set only
Wire (mm) 0.80 1.00 1.00 1.00 1.12 clear aside for
Mesh (mm) 15 25 30 40 50 away re-use
A B C D E F G H
Per square metre $ $ $ $ $ $ $ $
10342 Galvanized iron wire netting lapped 75 mm at joints
and bedded in floor screeds, paving, etc........................................................... 9.20 9.00 8.40 8.00 7.80 - - 5.10 10342
10343 Ditto but fixed to walls, wall lining or other vertical surfaces
as key for plaster or screed................................................................................ 10.90 10.70 10.10 9.70 9.40 - - 6.80 10343
10344 Ditto but fixed to soffits, or sides and soffits of beams
as key for plaster or screeds............................................................................... 12.60 12.30 11.80 11.40 11.10 - - 8.50 10344
10345 Ditto but fixed to timber, concrete or steel posts or framing
(measured separately) in fencing, gates, shelving, grilles, panels
and the like ........................................................................................................ 14.30 14.00 13.50 13.10 12.80 2.60 4.50 9.30 10345
Take Take
Supply and fix
down down Fix
Straight lattice mesh Diamond mesh and and set only
Wire (mm) 1.40 1.80 2.24 2.50 1.60 2.00 2.50 clear aside for
Mesh (mm) 5 10 13 16 25 30 40 away re-use
A B C D E F G H I J
Per square metre $ $ $ $ $ $ $ $ $ $
10346 Galvanized steel wire woven mesh fixed to
timber, concrete or steel posts or framing
(measured separately) in fencing, gates,
shelving, grilles, panels and the like............................. 52.70 49.70 53.70 54.20 35.20 36.30 37.80 3.20 6.40 13.50 10346
10/43
10 STEEL AND METAL WORK 10
Item Item
STEEL NETTING, MESH AND EXPANDED METAL Take Take
(CONT'D) Supply and fix down down Fix
and and set only
Wire (mm) 1.20 1.20 1.20 1.50 clear aside for
Mesh (mm) 12 x 12 12 x 25 25 x 25 50 x 50 away re-use
A B C D E F G
Per square metre $ $ $ $ $ $ $
10347 Galvanized steel welded wire mesh fixed to timber or steel posts or framing
(measured separately) in fencing, gates, shelving, racks, screens, window
guards, etc., including all galvanized staples, screws, typing wire and
the like (measured net)........................................................................................................ 34.00 32.20 30.00 29.20 2.60 4.50 9.30 10347
Take Take
Supply and fix
down down Fix
AISI 304 AISI 316 and and set only
Wire (mm) 2 3 3 4 2 3 3 4 clear aside for
Mesh (mm) 12 x 12 15 x 15 40 x 40 40 x 40 12 x 12 15 x 15 40 x 40 40 x 40 away re-use
A B C D E F G H I J K
Per square metre $ $ $ $ $ $ $ $ $ $ $
10348 Stainless steel welded wire mesh
fixed to timber, concrete or steel
posts or framing (measured
separately) in fencing, gates, shelving,
racks, screens, window guards, etc.,
including all galvanized staples,
screws, typing wire and the like
(measured net).............................................. 294.90 395.40 151.90 264.60 488.60 605.60 232.60 405.40 2.60 4.50 9.30 10348
Take Take
Supply and fix down down
Fix
and and set
only
Wire (mm) 2.50 3.15 5.30 4.00 clear aside for
Mesh (mm) 25 x 75 25 x 75 25 x 75 75 x 75 away re-use
A B C D E F G
Per square metre $ $ $ $ $ $ $
10349 Steel wire mesh fixed to timber, concrete or steel post framing
(measured separately) in fencing, gates, shelving, grilles,
panels and the like (measured net)...................................................................................... 41.60 43.80 39.10 39.70 2.60 4.50 9.30 10349
10350 Ditto but galvanized (ditto)................................................................................................. 43.80 45.70 40.80 41.40 3.20 5.10 10.10 10350
10/44
10 STEEL AND METAL WORK 10
Item Item
STEEL NETTING, MESH AND EXPANDED METAL (CONT'D) Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10351 Plastic dipped metal netting fixed to timber, concrete or steel posts or framing
(measured separately) in fencing, gates, shelving, grilles, panels and the like (measured net).............................................. 54.70 2.60 4.50 9.30 10351
Take Take
Supply and fix down down Fix
and and set only
Mesh (mm) 10 22 25 34 50 76 clear aside for
Weight (kg/m) 1.60 1.95 2.22 2.00 3.11 3.80 away re-use
A B C D E F G H I
Per square metre $ $ $ $ $ $ $ $ $
10352 Expanded metal fixed to timber, concrete, or steel post
framing (measured separately) in fencing gates,
shelving, grilles, panels and the like (measured net)...................... 44.80 54.60 62.20 56.00 87.10 106.40 3.20 5.10 12.70 10352
10353 Ditto but galvanised (ditto).............................................................. 56.80 69.20 78.70 70.90 110.30 134.80 3.20 5.10 12.70 10353
Supply and fix Take Take
77 30.48 38.1 down down Fix
Mesh (mm) x x x and and set only
34 13 16.93 clear aside for
Weight (kg/m) 5.91 7.38 12 away re-use
A B C D E F
Per square metre $ $ $ $ $ $
10354 Proprietary expanded metal for security fencing with hot dip
galvanized finish complied to BS EN ISO 1461.................................................................................. 215.50 219.30 279.80 3.20 5.70 12.70 10354
10/45
10 STEEL AND METAL WORK 10
Item Item
CHAIN LINK FENCING
Take Take
Supply and fix down down Fix
and and set only
Wire (mm) 2.50 3.00 3.00 3.00 4.00 clear aside for
Mesh (mm) 40 75 50 40 50 away re-use
A B C D E F G H
Per square metre $ $ $ $ $ $ $ $
10355 Galvanized steel chain link fencing fixed to
concrete, timber or steel posts ......................................................................... 25.90 26.20 33.60 43.30 57.00 2.60 4.50 9.30 10355
10356 Ditto but stainless steel chain link fencing....................................................... 104.20 102.80 111.40 134.50 154.00 2.60 4.50 9.30 10356
Take Take
Supply and fix down down Fix
and and set only
Wire (mm) 3.00 3.00 2.50 2.50 clear aside for
Mesh (mm) 75 50 40 25 away re-use
A B C D E F G
Per square metre $ $ $ $ $ $ $
10357 P.V.C. coated galvanised steel chain link fencing fixed to timber, concrete or
steel posts or framing (measured separately) in fencing, gates and the like ..................... 34.80 41.50 32.80 55.90 2.60 4.50 9.30 10357
BARBED WIRE OR TAPE Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per linear metre $ $ $ $
10358 Galvanised barbed wire formed from 2 strands of 2.5 mm mild steel line wires and 2 mm mild steel
pointed wires with set of two barbs at 125 mm centres, strained tight and fixed to fence top and steel
posts including all necessary tying wire, staples and the like (measured straight).................................................................. 3.90 0.60 1.30 3.40 10358
10359 Ditto but with sets of four barbs at 75 mm centre (measured straight).................................................................................... 4.90 0.60 1.30 3.40 10359
10360 Extra over either of Items 10358 to 10359 inclusive for forming into coils of any diameter.................................................. 4.90 - - 4.20 10360
10361 Extra over either of Items 10358 to 10359 inclusive for hand weaving into woven mat........................................................ 4.90 - - 4.20 10361
10362 Proprietary stainless steel razor barbed wire fence top and steel posts with any diameter coils
including all necessary stainless steel wire (measured straight).............................................................................................. 19.50 2.60 4.50 10.10 10362
10363 Proprietary stainless steel barbed wire fence top and steel posts with any diameter coils including
all necessary stainless steel wire (measured straight)............................................................................................................... 19.50 2.60 4.50 10.10 10363
10/46
10 STEEL AND METAL WORK 10
Item Item
FIXING BOLTS FOR ISOLATED REPAIRS TO SECURITY FENCING
Take Take
(Note : Items 10364 to 10369 inclusive shall only be measured when they are required for Supply down down Fix
replacement in isolated repair to security fencing as stipulated in Special Conditions and and and set only
Clauses SC10.11 and SC10.39.) fix clear aside for
away re-use
A B C D
Each $ $ $ $
10364 Fixing bolt with shear nuts and washers 6 mm diameter......................................................................................................... 7.80 1.90 2.60 4.20 10364
10365 Ditto but 8 mm diameter........................................................................................................................................................... 9.20 1.90 2.60 4.20 10365
10366 Ditto but 10 mm diameter......................................................................................................................................................... 11.20 2.60 1.90 5.10 10366
10367 Ditto but 12 mm diameter......................................................................................................................................................... 13.00 2.60 1.90 5.10 10367
10368 Ditto but 16 mm diameter......................................................................................................................................................... 17.90 2.60 3.20 5.90 10368
10369 U-bolt, hot dip galvanized with clamp plate and security shear nut........................................................................................ 38.00 2.60 3.20 5.90 10369
GALVANIZING, ELECTRO-PLATING AND CHROMIUM PLATING Zinc Electro Hot Chromium
sprayed plated dipped plated
A B C D
Each $ $ $ $
10370 Steel or cast iron articles complete with nuts, bolts or other fixing accessories,
n.e. 1 kg (weight of composite items measured) each in total weight..................................................................................... 6.80 7.60 8.60 19.40 10370
10371 Ditto but brass or copper articles.............................................................................................................................................. - - - 16.00 10371
Per kg
10372 Steel or cast iron articles complete with nuts, bolts or other fixing accessories,
1 - 13 kg (weight of composite items measured) each in total weight.................................................................................... 4.80 5.50 6.20 17.20 10372
10373 Ditto but exceeding 13 kg ditto................................................................................................................................................. 2.50 2.80 3.10 8.80 10373
10/47
10 STEEL AND METAL WORK 10
Item Item
PROPRIETARY FIRE PROTECTION ENCLOSURE AND CEILING
Proprietary fire protection enclosure and ceiling system complying with BS 476 : Parts 20-24 and statutory requirements,
complete with fire resisting boarding/material to all exposed surfaces, steel framings, insulation, and all necessary Supply
accessories in accordance with the manufacturers recommendations including providing test certificates : - and
fix
A
Per square metre $
10374 Proprietary fire protection enclosure of non-combustible composite panel of fibre reinforced cement, mechanically bonded to
punched steel sheet on both surfaces, 1 hour fire rated period (finishes measured separately).................................................................................................... 1,323.60 10374
10375 Ditto but 2 hours fire rated period (ditto)....................................................................................................................................................................................... 1,374.60 10375
10376 Ditto but 4 hours fire rated period (ditto)....................................................................................................................................................................................... 1,464.30 10376
10377 Proprietary fire protection enclosure of non-combustible calcium silicate board reinforced with selected fibres and fillers. The board
has smooth surface on one face and a lightly textured sanded surface on the other, 1 hour fire rated period (finishes measured
separately)........................................................................................................................................................................................................................................ 729.80 10377
10378 Ditto but 2 hours fire rated period (ditto)....................................................................................................................................................................................... 1,023.60 10378
10379 Proprietary fire protection enclosure of non-combustible calcium silicate board reinforced with selected fibres and fillers. The board
has smooth finish on both faces, 4 hour fire rated period (finishes measured separately)............................................................................................................ 1,172.10 10379
10380 Proprietary fire protection enclosure of non-combustible matrix engineered mineral boards, 1 hour fire rated period (finishes
measured separately)....................................................................................................................................................................................................................... 483.30 10380
10381 Ditto but 2 hours fire rated period (ditto)....................................................................................................................................................................................... 602.40 10381
10382 Ditto but 4 hours fire rated period (ditto)....................................................................................................................................................................................... 759.00 10382
10383 Proprietary fire protection enclosure of non-combustible board manufactured with a fibre reinforced cement core with outer facing
of perforated galvanized steel or other suitable materials mechanically bonded to each surface of the core, 1 hour fire rated period
(finishes measured separately)........................................................................................................................................................................................................ 1,286.50 10383
10384 Ditto but 2 hours fire rated period (ditto)....................................................................................................................................................................................... 1,328.20 10384
10385 Ditto but 4 hours fire rated period (ditto)....................................................................................................................................................................................... 1,417.90 10385
10386 Take down and clear away any type of fire protection enclosure or ceiling system...................................................................................................................... 92.50 10386
10/48
10 STEEL AND METAL WORK 10
Item Item
FIRE RESISTING DOOR SETS
Take Take
Approved galvanised mild steel fire resisting door and frame set of Supply and fix down down Fix
fire rated period tested in accordance with BS 476 : Parts 20-23 : - and and set only
Fire rated period clear aside for
1/2 hour 1 hour 2 hours 4 hours away re-use
A B C D E F G
Per square metre $ $ $ $ $ $ $
(Door panel size measured net)
10387 Fire resisting door, single leaf............................................................................................. 2,508.80 2,548.10 2,588.10 3,719.30 28.70 35.70 69.20 10387
10388 Fire resisting door, double leaf............................................................................................ 1,769.10 1,798.90 1,829.30 2,439.50 23.00 28.70 55.70 10388
Per linear metre
10389 Fire and smoke seals, tested in accordance with BS 476 : Parts
20/22 and BS 476-31.1:1983 including any finish............................................................. 148.60 148.60 148.60 148.60 1.90 3.20 6.80 10389
Fire rated period
hour 1 hour 2 hours 4 hours
A B C D
Each $ $ $ $
10390 Extra over either of Items 10387 to 10388 inclusive for observation panel n.e. 0.10 m........................................................ 135.50 135.50 156.90 235.30 10390
10391 Ditto but 0.10 - 0.20 m............................................................................................................................................................. 338.70 338.70 392.20 588.30 10391
10392 Ditto but 0.20 - 0.40 m............................................................................................................................................................. 541.90 541.90 627.40 941.20 10392
Approved stainless steel fire resisting door and frame set of fire Take Take
rated period tested in accordance with BS 476 : Parts 20-23 : - Supply and fix down down Fix
and and set only
Fire rated period clear aside for
hour 1 hour 2 hours 4 hours away re-use
A B C D E F G
Per square metre $ $ $ $ $ $ $
(Door panel size measured net)
10393 Fire resisting door, single leaf............................................................................................. 6,981.00 7,092.40 7,205.50 9,398.40 28.70 35.70 69.20 10393
10394 Fire resisting door, double leaf............................................................................................ 6,033.60 6,131.70 6,229.80 8,125.50 23.00 28.70 55.70 10394
Per linear metre
10395 Fire and smoke seals, tested in accordance with BS 476 : Parts 20/22
and BS 476-31.1:1983 including any finish....................................................................... 148.60 148.60 148.60 148.60 1.90 3.20 6.80 10395
10/49
10 STEEL AND METAL WORK 10
Item Item
FIRE RESISTING DOOR SETS (CONT'D)
Approved stainless steel fire resisting door and frame set of fire rated period
tested in accordance with BS 476 : Parts 20-23 : - (Cont'd) Fire rated period
hour 1 hour 2 hours 4 hours
A B C D
Each $ $ $ $
10396 Extra over either of Items 10393 to 10394 inclusive for forming observation panel n.e. 0.10 m.......................................... 135.50 135.50 156.90 235.30 10396
10397 Ditto but 0.10 - 0.20 m............................................................................................................................................................. 338.70 338.70 392.20 588.30 10397
10398 Ditto but 0.20 - 0.40 m............................................................................................................................................................. 541.90 541.90 627.40 941.20 10398
Approved fire resisting glazed doors and frame set of fire rated period tested in accordance Take Take
with BS 476 : Parts 20-23 comprising fire resisting clear tempered glass panels and mirror Supply down down Fix
finished stainless steel door frames : - and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
(Door panel size measured net)
10399 Single leaf door, 1 hour fire rated period with fire resisting clear tempered glass panels....................................................... 5,813.40 18.50 18.50 35.50 10399
10400 Ditto but double leaf door......................................................................................................................................................... 5,473.30 16.60 16.60 32.10 10400
10401 Single leaf door, 2 hours fire rated period with fire resisting clear tempered glass panels..................................................... 8,151.20 19.80 19.80 38.90 10401
10402 Ditto but double leaf door......................................................................................................................................................... 7,688.80 18.50 18.50 35.50 10402
FIRE RESISTING PARTITIONS
Approved fire resisting glazed partition comprising fire resisting glass panels, galvanized mild
steel frames, stainless steel beads and cladded with stainless steel facing in any finish complying
with BS 476 : Parts 20-24 : -
Per square metre
10403 Approved glazed partition with 6 mm thick fire resisting clear tempered glass with
1 hour fire rated period.............................................................................................................................................................. 1,736.30 45.30 69.50 135.10 10403
10404 Ditto but with 12 mm thick fire resisting clear tempered glass with 1 hour fire rated period................................................. 2,025.80 52.90 81.00 156.20 10404
10/50
10 STEEL AND METAL WORK 10
Item Item
FIRE RESISTING PARTITIONS (CONT'D)
Proprietary fire resisting partition wall system comprising steel framing with gypsum board and versatile Take Take
lining board, composed of calcium silicate and cellulose reinforced fibre, on both sides. The works shall Supply down down Fix
include sealing up head and bottom and joint with tape and compound in accordance with manufacturer's and and and set only
instructions and complying with BS 476 : Parts 20-24 : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10405 Proprietary fire resisting partition wall, 1 hour fire rated period............................................................................................. 314.60 33.80 44.60 84.40 10405
10406 Ditto, but 2 hours fire rated period............................................................................................................................................ 393.90 33.80 44.60 84.40 10406
Proprietary fire resisting partition system comprising steel framing, insulation, and all necessary
accessories in accordance with the manufacturers recommendations and complying with BS 476 :
Parts 20-24 : -
Per square metre
10407 Proprietary fire resisting partition comprising non-combustible composite panel of fibre
reinforced cement, mechanically bonded to punched steel sheet, 1 hour fire rated period
(finishes measured separately).................................................................................................................................................. 1,622.70 63.10 96.90 185.80 10407
10408 Ditto but 2 hours fire rated period (ditto)................................................................................................................................. 1,673.60 63.10 96.90 185.80 10408
10409 Ditto but 4 hours fire rated period (ditto)................................................................................................................................. 1,942.80 63.10 96.90 185.80 10409
10410 Proprietary fire resisting partition comprising non-combustible calcium silicate board
reinforced with selected fibres and fillers. The board has smooth surface on one face and
a lightly textured sanded surface on the other, 1 hour fire rated period (finishes measured
separately).................................................................................................................................................................................. 902.30 80.40 100.80 241.50 10410
10411 Ditto but 2 hours fire rated period (ditto)................................................................................................................................. 1,044.20 80.40 100.80 241.50 10411
10412 Ditto but 4 hours fire rated period (ditto)................................................................................................................................. 1,284.30 80.40 100.80 241.50 10412
10413 Proprietary fire resisting partition comprising non-combustible matrix engineered mineral
boards, 1 hour fire rated period, with or without lining (finishes measured separately)......................................................... 817.60 80.40 100.80 211.10 10413
10414 Ditto but 2 hours fire rated period (ditto)................................................................................................................................. 937.90 80.40 100.80 211.10 10414
10415 Ditto but 4 hours fire rated period (ditto)................................................................................................................................. 1,132.60 80.40 100.80 211.10 10415
10416 Proprietary fire resisting partition comprising non-combustible board manufactured with fibre
reinforced cement core with outer facing of perforated galvanized steel or other suitable
materials mechanically bonded to each surface of the core, 1 hour fire rated period, with or
without lining (finishes measured separately).......................................................................................................................... 1,677.20 80.40 100.80 211.10 10416
10417 Ditto but 2 hours fire rated period (ditto)................................................................................................................................. 1,746.40 80.40 100.80 211.10 10417
10418 Ditto but 4 hours fire rated period (ditto)................................................................................................................................. 2,015.60 80.40 100.80 211.10 10418
10/51
10 STEEL AND METAL WORK 10
Item Item
FIRE RESISTING SHUTTERS Take Take
Supply down down Fix
Approved fire resisting shutters comprising steel framing tested in accordance and and and set only
with BS 476: Parts 20-24 : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10419 Fire resisting drop shutter, 2 hours fire rated period ............................................................................................................... 4,225.10 108.40 131.40 346.20 10419
10420 Ditto but 4 hours fire rated period (ditto)................................................................................................................................. 4,995.40 108.40 131.40 346.20 10420
10421 Fire resisting slide shutter, 2 hours fire rated period................................................................................................................ 11,285.10 108.40 131.40 346.20 10421
PROPRIETARY FIRE RESISTING LOUVRES
Proprietary fire resisting louvres, tested in accordance with BS476 comprising steel framing and all Take Take
accessories in accordance with the manufacturer's recommendations and provision of connection Supply down down Fix
to nearest power point by registered electrical workers: - and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10422 Proprietary fire resisting louvre, 2 hours fire rated period....................................................................................................... 8,716.90 108.40 131.40 346.20 10422
FIRE RESISTING ROLLER SHUTTERS Take Take
Supply and fix down down Fix
Fire resisting roller shutters tested in accordance with BS 476 : Parts 20-24 comprising and and set only
framing and shutter hood : - Fire rated period clear aside for
1 hour 2 hours away re-use
A B C D E
Per square metre $ $ $ $ $
10423 Fire resisting roller shutter, galvanized mild steel, manually operated.................................................................. 1,396.70 1,982.20 158.80 208.60 405.30 10423
10424 Fire resisting roller shutter, galvanized mild steel, electrically operated including
provision of connection to nearest power point by registered electrical workers.................................................. 1,773.00 1,923.40 198.40 260.90 506.70 10424
10425 Fire resisting roller shutter, stainless steel, manually operated.............................................................................. 2,185.10 2,238.40 158.80 208.60 405.30 10425
10426 Fire resisting roller shutter, stainless steel, electrically operated including
provision of connection to nearest power point by registered electrical workers.................................................. 2,759.30 2,851.20 198.40 260.90 506.70 10426
10/52
10 STEEL AND METAL WORK 10
Item Item
CURTAIN WALLS Take Take
Supply down down Fix
Design, supply, fabricate and install glazed/unglazed aluminium curtain wall including framing and and and set only
components and sub-frames : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10427 Aluminium curtain wall............................................................................................................................................................ 1,564.30 185.60 364.80 878.20 10427
10428 Ditto but circular on plan.......................................................................................................................................................... 1,801.40 199.00 391.60 937.30 10428
10429 Extra over either of Items 10427 to 10428 inclusive for openable portion............................................................................. 124.10 14.00 33.20 64.20 10429
10430 Extra over either of Items 10427 to 10428 inclusive for louvres............................................................................................. 271.60 28.70 67.00 129.20 10430
Design, supply, fabricate and install glazed/unglazed stainless steel curtain wall including framing
components and sub-frames : -
Per square metre
10431 Stainless steel curtain wall........................................................................................................................................................ 2,348.30 177.90 327.80 785.30 10431
10432 Ditto but circular on plan.......................................................................................................................................................... 2,780.90 191.30 352.10 844.40 10432
10433 Extra over either of Items 10431 to 10432 inclusive for openable portion............................................................................. 187.70 23.00 49.70 97.10 10433
10434 Extra over either of Items 10431 to 10432 inclusive for louvres............................................................................................. 387.90 37.00 83.60 160.40 10434
PROPRIETARY COMPOSITE ALUMINIUM CLADDING
Design, supply, fabricate and install proprietary composite aluminium cladding all in accordance Take Take
with the manufacturer's instructions : - Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10435 Cladding minimum 3 mm thick internally................................................................................................................................ 1,272.90 186.20 329.70 413.80 10435
10436 Ditto but circular on plan.......................................................................................................................................................... 1,336.50 195.80 360.30 447.50 10436
10437 Cladding minimum 3 mm thick externally............................................................................................................................... 1,371.80 198.40 352.70 439.10 10437
10438 Ditto but circular on plan.......................................................................................................................................................... 1,440.40 209.20 384.60 472.90 10438
COMPOSITE ALUMINIUM LINING
Design, supply, fabricate and install composite aluminium lining all in accordance with the Take Take
manufacturer's instructions : - Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10439 Lining minimum 3 mm thick as internal infill panelling......................................................................................................... 885.00 95.70 127.60 211.10 10439
10440 Ditto but circular on plan.......................................................................................................................................................... 916.80 100.40 133.90 221.70 10440
10/53
10 STEEL AND METAL WORK 10
Item Item
PROPRIETARY AUTOMATIC SWING AND SLIDING DOORS
Proprietary automatic swing or sliding door system in accordance with the manufacturer's instructions comprising clear tempered
glass panels and mirror finished or other finished stainless steel door frames. The works shall include door operator to Supply
comply with BS 7036, safety unit, locks and all necessary accessories and provision of connection to nearest power point by and
registered electrical workers : - fix
A
Per square metre $
10441 Proprietary automatic swing door; single leaf door........................................................................................................................................................................ 16,939.70 10441
10442 Ditto but double leaf door............................................................................................................................................................................................................... 16,299.40 10442
10443 Proprietary automatic sliding door; single leaf door...................................................................................................................................................................... 20,374.20 10443
10444 Ditto but double leaf door............................................................................................................................................................................................................... 19,908.50 10444
STRONG ROOM DOORS AND FRAMES
Supply and fix strong room door and frame, complete with all boltwork, locking, anti-explosive Take Take
protection and fire protection, in accordance with G.S. Item 22.50 : - Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
10445 Single leaf Treasury Grade "C" door......................................................................................................................................... 17,209.30 134.60 247.50 793.80 10445
10446 Ditto but Treasury Grade "D".................................................................................................................................................... 15,303.30 113.50 209.20 675.50 10446
10447 Ditto but Treasury Grade "E".................................................................................................................................................... 12,622.10 93.10 170.90 456.80 10447
(Note : - The above Items 10445 to 10447 inclusive will only be paid for, if ordered by the Maintenance
Surveyor in writing.)
FIBREGLASS HOUSE AND PLANTER
Fibreglass house equipped with windows, door, louvres and all necessary accessories in Take Take
accordance with the manufacturer's instructions : - Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per set $ $ $ $
10448 Combinable house size 1520 x 1220 x 2250 mm high and sun cover size 2400 x 1500 x 150 mm high.............................. 7,696.10 354.60 318.90 613.10 10448
10449 Guard house size 1250 x 1250 x 2100 mm high and sun cover size 1800 x 1500 x 150 mm high........................................ 7,076.90 281.90 255.10 487.20 10449
10450 Guard house size 3460 x 1520 x 2350 mm high and sun cover size 3800 x 1800 x 150 mm high........................................ 17,371.60 959.90 892.90 1,655.10 10450
Fibreglass planters with galvanized mild steel framing in any colour finish and all necessary
accessories in accordance with the manufacturer's instructions : -
Each
10451 Planter size 1200 x 1200 x 1200 mm high............................................................................................................................... 4,325.40 149.20 133.90 257.60 10451
10/54
10 STEEL AND METAL WORK 10
Item Item
SUPPLY ONLY OF MATERIALS
MILD STEEL
A
Per kg $
10452 Square rods or flat bars, plates, angle sections, tee sections.......................................................................................................................................................... 9.50 10452
GALVANIZED MILD STEEL
A
Per kg $
10453 Flat bars, round rods, square rods, plates, angle sections, tee sections and chequer plates.......................................................................................................... 10.60 10453
STAINLESS STEEL AISI AISI
304 316
A B
Per kg $ $
10454 Square or flat bars, round bars, square or rectangular hollow tubes, hollow circular tubes, equal or
unequal angle, tee or channel sections ......................................................................................................................................................................... 50.20 77.20 10454
CAST IRON
Supply only the following cast iron items including making patterns for articles as required (fixing measured in Brickwork
and Blockwork Section of this Schedule) : -
A
Per kg $
10455 Combined gate, tree grilles, covers, fireplace surround, mantel, range, damper and frame, soot door, fire door, fireplace fret,
fire bar and the like except manhole covers and frames n.e. 6.0 kg in weight each...................................................................................................................... 9.50 10455
10456 Ditto but exceeding 6.0 kg in weight each..................................................................................................................................................................................... 9.10 10456
NON FERROUS METAL
A
Per kg $
10457 Extruded aluminium sections with clear anodized finish in square or flat bars, round bars, square or rectangular hollow tubes,
hollow circular tubes, equal or unequal angle, tee or channel sections......................................................................................................................................... 41.00 10457
Approved stove enamelled slotted steel angel section complete with fixing screws, bolts, nuts washers and corner stiffeners : -
Per linear metre
10458 36 x 36 x 1.8 mm Slotted angle section.......................................................................................................................................................................................... 22.50 10458
10459 40 x 40 x 2.00 mm Ditto................................................................................................................................................................................................................. 27.00 10459
10460 62 x 41 x 2.00 mm Ditto................................................................................................................................................................................................................. 29.80 10460
10461 66 x 45 x 2.50 mm Ditto................................................................................................................................................................................................................. 39.10 10461
10/55
10 STEEL AND METAL WORK 10
Item Item
SUPPLY ONLY OF MATERIALS (CONT'D)
EXPANDED METAL 77 30.48 38.10
Mesh (mm)
x 34 x 13 x 16.93
Weight (kg/m) 5.91 7.38 12
A B C
Per square metre $ $ $
10462 Proprietary expanded metal for security fencing with hot dip galvanized finish...................................................................................... 229.70 234.00 302.40 10462
FENCING
Wire (mm) 2.50 3.00 3.00 3.00 4.00
Mesh (mm) 40 75 50 40 50
A B C D E
Per square metre $ $ $ $ $
10463 Galvanized iron wire chain link fencing................................................................................................................. 18.90 19.10 27.50 38.50 54.00 10463
Wire (mm) 3.00 3.00 2.50 2.50
Mesh (mm) 75 50 40 25
A B C D
Per square metre $ $ $ $
10464 P.V.C. coated galvanized steel chain link fencing................................................................................................................... 28.80 36.50 26.60 52.80 10464
10/56
Section 11
PLASTERING AND FINISHES
11 PLASTERING AND FINISHES 11
SECTION 11
PLASTERING AND FINISHES
SPECIAL CONDITIONS
Specification SC11.01 The standard drawings referred to in this Section and listed in Annex 'A' - Drawing
and Drawings Schedule and Drawings for Builder's Works of the Schedule can be viewed on the
ArchSD internet website via the pathway referred therein.
This Section shall generally be read and used in conjunction with the Specification adopted
in the Contract.
Measurement SC11.02 All works shall be measured the net area covered. Unless otherwise stated, no deduction
generally shall be made for voids or openings not exceeding 0.50 m, nor for unbracketed cornice,
mouldings and the like of any width. Thickness shall be measured from the general face
of the surface being covered and exclusive of any grooves, raked out joints or other
irregularities.
Measurement SC11.03 Notwithstanding definitions of ceramic floor and wall tiles in BS EN 14411 and
of tiling BS EN ISO 10545 : -
(a) Measurement of ceramic tiles and quarry tiles shall include homogeneous ceramic,
porcelain, stoneware or similar tiles.
(b) Measurement of floor tiles described as anti-slip shall have suitably embossed surface
or with surface treated with carborundum or similar grit to comply with relevant
standards as stated in G.S. Item 18.103.
(c) Measurement of ceramic floor and wall tiles shall include glazed or unglazed tiles of
engobed, matt, non-slip or similar properties.
Measurement SC11.04 Mouldings and moulded cornices shall be measured the net length on wall or beam face by
of mouldings the net visible girth.
Measurement SC11.05 Skirting shall be measured the net height above finished floor or paving level. The thickness
of skirting of skirting shall be measured at the centre point of the height.
Measurement SC11.06 Each isolated patch is defined as the isolated surface required for tile replacement up to a
of hack out and maximum of 10 number of tiles and area not exceeding 0.50 m.
replace tile in
isolated patches
Measurement SC11.07 Suspended ceiling systems shall be measured over the net area covered including air grilles,
of suspended light fittings, access panels and the like. Deduction shall be made for areas covered by columns.
ceiling systems
Sheet metal or wooden bulkheads shall be measured separately and paid for at the appropriate
rates under applicable Work Sections in this Schedule.
11/1
11 PLASTERING AND FINISHES 11
SPECIAL CONDITIONS
Measurement SC11.08 Raised accessed flooring shall be measured over the net area covered including air
of raised grilles, access openings and the like.
accessed flooring
Measurement SC11.09 All works shall be measured over the net area covered to horizontal or sloping surfaces
of carpeting and shall deem to include for vertical surfaces of upstands curbs, channels and the like.
Measurement SC11.10 Entrance matting shall be measured the net area fixed. Forming matt well shall be
of entrance measured elsewhere in this Schedule.
matting
Rates generally SC11.11 The rates shall generally include for the following : -
(a) Narrow widths and small quantities.
(b) Preparation of surfaces to receive the finishing and any necessary dubbing out of
irregularities on the surface being covered.
(c) Working into channels and recessed covers and working around pipes, metal
sections and the like.
(d) Laying or executing work in bays or between strips, circular or pattern.
(e) Laying level or to slopes and finishing to falls or currents.
(f) All temporary formwork or rules.
(g) All cutting and wastes, holes, notches, cutting and fitting and making good.
(h) Executing internally or externally, working in any position, at any height and on
new or existing surfaces including any scaffolding and all temporary works.
(i) All quoin points and other intersections of curved surfaces.
(j) All making good up to existing finishes, door and window frames, around pipes,
brackets and the like, and dishing to outlets.
(k) All internal and external angles, fair ends, stopped ends and similar labours.
(l) All joints between different types of materials and joints between new and existing
surfaces including wire netting as G.S. Item 18.14.
(m) Any dressing around pipes passing through roofs as G.S. Item 18.82.
(n) Covering up and protecting where necessary.
(o) Construction and subsequent demolition of trial panels of finishings.
(p) Provision of samples and tests including submission of records and reports for
approval by the Maintenance Surveyor.
(q) All necessary tests as specified under the Specification and provision of test
certificates when required.
11/2
11 PLASTERING AND FINISHES 11
SPECIAL CONDITIONS
Rates for SC11.12 The rates for proprietary plaster and screeds shall further include for : -
proprietary
plaster and (a) Supplying and laying in accordance with the manufacturer's instruction.
screeds
(b) Cleaning existing surfaces by high pressure water jets.
(c) Repairing cracks and applying floor primer or bonding agent.
(d) Submission of manufacturer's guarantee.
Rates for SC11.13 The rates for metal lathing and wire netting shall further include for : -
metal lathing
and wire (a) Preparing and applying one coat of bituminous paint to cut ends.
netting
(b) Fixing to supports with staples or tying wire.
(c) Allowing for bending and laps.
(d) All circular cutting and waste.
Rates for SC11.14 The rates for screeds, rendering, plastering, granolithic and terrazzo works and any other
screeds and in-situ finishes shall further include for : -
in-situ finishes
(a) Spatterdashing, hacking, raking out joints, washing over with cement grout,
brushing down, cleaning and all other preparation works required to new or
existing surfaces to provide key or bonding.
(b) All internal angles, arrises, quirks, throats, drips, rounded angles and coves and
similar labours, and forming V or square edged grooves in surface when
required.
(c) Scratching undercoats, and steel trowel, wood float, trowelled stucco, brushed,
or combed finish as ordered.
(d) All metal beads as G.S. Items 18.25 and 18.53.
Rates for SC11.15 The rates for proprietary waterproofing protective screeds shall further include for : -
proprietary
waterproofing (a) Supplying and laying in accordance with the manufacturer's instruction.
protective
screeds (b) Cleaning existing surfaces by high pressure water jets.
(c) Repairing cracks and applying floor primer or bonding agent.
(d) Submission of manufacturer's guarantee.
11/3
11 PLASTERING AND FINISHES 11
SPECIAL CONDITIONS
Rates for acoustic SC11.16 The rates for acoustic plaster or cementitious fireproofing plaster shall further include for : -
plaster or fire
resisting (a) Application by special spray equipment.
cementitious
fireproofing (b) Coloured top coat.
plaster
(c) Supply and spraying in accordance with the manufacturer's recommendations.
(d) Submission of manufacturer's guarantee.
Rates for SC11.17 The rates for terrazzo shall further include for : -
terrazzo
(a) Preparing and applying one coat of wax polish to wall and floor finishes in
accordance with G.S. Item 18.97.
Rates for SC11.18 The rates for terrazzo tiles shall further include for : -
terrazzo
tiles (a) Forming rounded, squared or splayed edges as required.
(b) Pointing in natural or coloured cement slurry.
(c) Preparing and applying one coat of wax polish to wall tiles or two coats non-slip,
matt emulsion polish on floor tiles.
Rates for SC11.19 The rates for tiling, slabs or paving blocks shall further include for : -
tiling, slabs or
paving blocks (a) Special tiles or fittings. In the case of no special tiles or fittings, mitring edges to
external corners and the like.
(b) All slurry, grout, mortar and the like of approved type.
(c) Tile adhesives of approved proprietary type to BS EN 12004.
(d) Pointing joints with natural or coloured cement slurry or cement and sand grout to
match colours of tiles.
(e) Grouting up joints in approved grout or a proprietary grout to BS EN 13888.
(f) Cutting and laying or fixing to patterns including graphics.
(g) Unless otherwise stated, tiles of any configuration or dimension.
(h) Unless otherwise stated, any type of finish, likewise, matt, non-slip or polished
finishes.
11/4
11 PLASTERING AND FINISHES 11
SPECIAL CONDITIONS
Rates for SC11.20 The rates for Extra over for rounded edge tiles, skirting tiles and the like shall further
Extra over include for : -
for rounded
edge tiles, (a) All internal and external corner tiles, corner end tiles and the like.
skirting tiles
and the like
Rates for SC11.21 The rates for flexible tiles and sheet finishes, or rubber tiles and sheet finishes shall
flexible tiles further include for : -
and sheet
finishes, or (a) Providing and laying tiles or sheets with adhesives in accordance with the
rubber tiles manufacturer's instructions.
and sheet
finishes (b) Laying tiles or sheets in plain or pattern including graphics.
(c) Preheating process with preheating tools as required.
(d) Any welding joints between sheets including approved P.V.C. welding rods.
(e) Treating surfaces of tiles or sheets as G.S. Item 18.140.
(f) Execution by approved specialist contractor.
Rates for SC11.22 The rates for swimming pool tiles shall further include for : -
swimming
pool tiles (a) Provision of tile adhesive that is able to withstand continual immersion in water and
has acid resistant and hygiene properties.
(b) Pointing and grouting joints with cement based, water repellent floor grouting with
hard abrasion resistant finish, and resistant to dirt penetration.
Rates for SC11.23 The rates for pavers shall include for : -
pavers
(a) Excavation to reduced level or filling to make up levels, compacting bottom properly
to receive granular sub-base.
(b) Grading, measuring, mixing, transporting, depositing, spreading, levelling and
compacting granular sub-base.
(c) Sand filling, mortar bedding and the like.
(d) Cutting and making good at boundaries, manholes and the like.
(e) Laying at any designated pattern or design as specified by the Maintenance Surveyor
using multi-coloured paving slabs and paving blocks as required.
(f) Use of recycled aggregate as specified in the G.S. Items 6.42.3 (xiii) and 8.22 for
designed concrete mixes and prescribed concrete mixes respectively, when required.
11/5
11 PLASTERING AND FINISHES 11
SPECIAL CONDITIONS
Rates for SC11.24 The rates for stone or marble slabs/tiles and resin stone slabs shall further include for : -
stone or
marble slabs / (a) Forming rounded, squared or splayed edges as required.
tiles and resin
stone slabs (b) Pointing in natural or coloured grout.
(c) Preparing and applying one coat of wax polish to wall slabs or two coats non-slip,
matt emulsion polish on floor slabs.
(d) Providing and fixing copper cramps and S hooks as G.S. Item 18.126 or stainless
steel fixing as ordered.
(e) Laying level or to slopes and finishing to falls, or falls and currents.
(f) Preparing surfaces ready to receive cement and sand bedding or sand bedding to
receive stone paving or slabs.
(g) All joints between different types of materials and joints between new and existing
materials.
(h) Flushing up around pipes, floor drains, outlets and the like.
(i) Covering up and protecting.
(j) Providing one coat of approved sealer at back of stone paving or slabs.
(k) Submission of design and calculations endorsed by Registered Structural Engineer
for fixing of stone or marble slabs and resin stone slabs to vertical or sloping surfaces.
(l) Unless otherwise stated, natural stone or marble are of origin from China or Asian
countries (other than Japan).
Rates for SC11.25 The rates for division strips, cover angles, strips at expansion joints etc. to finishes and pavings
division strips shall include for cutting to required lengths, splay cut ends, drilling, fixing with brass or
stainless steel screws or the like and for countersinking the heads of all exposed screws.
Rates for SC11.26 The rates for suspended ceiling systems shall include for : -
suspended
ceiling systems (a) Design, supply and install the suspended ceiling systems complete with necessary
linings and including suspension framing, edge trims, runners, hangers and the like,
and fixing to concrete soffits and the like.
(b) All cutting and narrow widths.
(c) Unless otherwise stated, any drop length from soffits.
(d) Forming openings and trimming around pipes, conduits, power points and the like
and including extra supports and trimmers for same.
11/6
11 PLASTERING AND FINISHES 11
SPECIAL CONDITIONS
Rates for SC11.26 (e) Trimming around sprinkler and detector heads, air grilles, light fittings, access
suspended (Cont'd) panels and the like and including extra supports and trimmers for same.
ceiling systems
(Cont'd) (f) Additional framing and supports etc. to bridge across ducts and the like.
(g) Submission of catalogues, technical literature, data and the like on the suspended
ceiling systems.
(h) Submission of design drawings, working details and shop drawings for Maintenance
Surveyor's approval prior to commencement of installation.
(i) Submission of test certificates and manufacturer's guarantee.
Rates for SC11.27 The rates for Extra over for forming openings shall further include for : -
Extra over
for forming (a) Additional trimmer/suspension, stiffening plates, brackets, etc.
openings
(b) Sealing edges.
Rates for SC11.28 The rates for raised accessed flooring shall further include for : -
raised
accessed (a) Design, supply and installation in accordance with the manufacturer's instructions.
flooring
(b) Additional supports and framing for cut panels.
(c) All air grilles, skirting trims, integral fittings and the like.
(d) Forming openings for power points, trunking and other building services installations
including sealing edges.
(e) Providing and laying insulation under floor as required.
(f) All preparation works, cleaning and protection of completed works.
(g) Submission of design drawings, working details and shop drawings for Maintenance
Surveyor's approval prior to commencement of installation.
(h) Submission of test certificate, manual and manufacturer's guarantee.
Rates for SC11.29 The rates for carpeting or carpeting with underlays shall generally include for : -
carpeting or
carpeting with (a) Working to narrow widths and small areas.
underlays
generally (b) Working to flat or sloping surfaces.
(c) New and existing surfaces.
(d) All necessary cleaning and preparation of substrate prior to the laying of carpet,
carpet tiles or underlays.
(e) Proprietary release bond agent, approved sealants, tapes, adhesive, carpet grippers
and seaming cement, where necessary.
11/7
11 PLASTERING AND FINISHES 11
SPECIAL CONDITIONS
Rates for SC11.29 (f) Providing underlays in accordance with G.S. Item 18.155 and fixing underlays in
carpeting or (Cont'd) accordance with G.S. Item 18.160.
carpeting with
underlays (g) Laying of carpet including straight, raking or circular cutting and waste, seaming and
generally jointing as G.S. Item 18.161, sewing and fixing all smooth edges and carpet trims.
(Cont'd)
(h) Fixing and trimming, cutting and fitting carpets to floor mounted services outlets
including electric power point, telephone box, recessed removable covers and the
like including binding edges as required.
(i) Bonding to match existing works.
(j) Provision of protective treatment and cleaning.
(k) Provision of test certificates, manufacturer's guarantee and the like for carpet and
underlays.
Rates for SC11.30 The rates for carpet tiles shall further include for : -
carpet tiles
(a) Treating surfaces with approved protective treatment.
Rates for SC11.31 The rates for entrance matting shall include for : -
entrance
matting (a) Working to narrow widths and small areas.
(b) Working to flat or sloping surfaces.
(c) New and existing surfaces.
(d) All necessary framing and fixing accessories.
(e) All necessary cleaning and preparation of substrate prior to the fixing of entrance
matting.
(f) Protection and cleaning.
(g) Provision of samples, literature, test certificates and manufacturer's guarantee.
Rates for SC11.32 The rates for taking down existing plaster, paving, tiling, etc., shall include for : -
taking
down (a) Cutting back edges of the retaining work.
existing
finishes (b) Cutting and clearing away steel lathing of wire netting as required.
(c) Cutting by manual or mechanical means including saw cutting.
(d) Making good adjoining surfaces disturbed in the taking down process.
(e) Preparing joints for new work.
(f) Preparing surfaces to receive new finish.
11/8
11 PLASTERING AND FINISHES 11
SPECIAL CONDITIONS
Rates for SC11.33 The rates for Take up and clear away existing carpet or carpet tiles shall generally
Take up and include for : -
clear away
existing (a) Taking up and clearing away existing carpet by hand or power tools or both.
carpet or
carpet tiles (b) Removal of associated adhesive and release bond agent.
generally
(c) Removal of associated underlays and carpet grippers.
(d) Making good affected surfaces.
G.S. clauses SC11.34 G.S. clauses for suspended ceiling systems can be found in the Carpentry and Joinery
for suspended Section of the General Specification for Building.
ceiling
systems
11/9
11 PLASTERING AND FINISHES 11
Item Item
METAL LATHING AND NETTING
Supply and fix
Wire
Plain Ribbed netting
expanded expanded 0.9 mm
type type dia. x
1.6kg/m 2.25kg/m 50 mm
mesh
A B C
Per square metre $ $ $
11001 Vertical or horizontal surfaces.................................................................................................................................................................... 27.60 35.60 15.70 11001
11002 Soffits or sloping soffits including beams and the like.............................................................................................................................. 28.60 36.60 16.60 11002
SAND BEDDING Thickness (mm)
25 50
A B
Per square metre $ $
11003 Sand bedding to receive paving slab or block, pavers, etc........................................................................................................................................... 16.40 24.10 11003
LIGHTWEIGHT FLOOR AND ROOF SCREEDS Thickness (mm)
40 50 65 75
A B C D
Per square metre $ $ $ $
11004 Cement and vermiculite (1:8 by volume) roofing screed......................................................................................................... 85.40 104.50 142.60 161.70 11004
11005 Cement and vermiculite (1:6 by volume) floor screed ............................................................................................................ 83.40 102.00 139.10 157.70 11005
11006 Air entrained screed having a dry density of not more than 1,200 kg/m................................................................................ 97.30 119.30 163.40 185.40 11006
CEMENT PAVING, FLOOR SCREEDS, ETC. Cement and sand (1:3) or cement
and granite fines (1:3)
Thickness (mm)
15 20 25 30 40
A B C D E
Per square metre $ $ $ $ $
11007 Paving or floor screeds............................................................................................................................................ 30.00 33.20 36.30 39.50 45.80 11007
11008 Paving or screed to treads and risers, strings, sides and top of upstand kerbs, sides and bottom
of channels and sinkings and the like .................................................................................................................... 40.10 42.80 46.70 49.40 56.00 11008
11009 Extra over either of Items 11007 to 11008 inclusive for approved admixture of hardener
and/or dust proofer.................................................................................................................................................. 17.30 21.50 25.60 29.80 38.10 11009
11010 Extra over either of Items 11007 to 11008 inclusive for approved admixture of waterproofing.......................... 5.00 5.40 6.70 7.10 8.80 11010
11011 Extra over either of Items 11007 to 11008 inclusive for approved colour cement or pigments........................... 4.70 5.70 6.60 8.00 9.90 11011
11/10
11 PLASTERING AND FINISHES 11
Item Item
CEMENT PAVING, FLOORS SCREEDS, ETC. (CONT'D)
Cement, sand or
granite fines and
coarse aggregate
Grade 10 (1:1.5:3)
Thickness (mm)
50 60
A B
Per square metre $ $
11012 Paving or floor screeds.................................................................................................................................................................................................. 47.70 53.80 11012
11013 Paving or screed to treads and risers, strings, sides and top of upstand kerbs, sides and bottom of channels and sinkings
and the like.................................................................................................................................................................................................................... 51.60 57.70 11013
11014 Extra over either of Items 11012 to 11013 inclusive for approved admixture of hardener and/or dust proofer........................................................ 29.90 38.90 11014
11015 Extra over either of Items 11012 to 11013 inclusive for approved admixture of waterproofing................................................................................ 11.50 15.10 11015
11016 Extra over either of Items 11012 to 11013 inclusive for approved coloured cement or pigments............................................................................. 10.30 12.30 11016
Cement and sand (1:4) or cement and granite fines (1:4)
Thickness (mm)
15 20 25 30 40 50 65
A B C D E F G
Per square metre $ $ $ $ $ $ $
11017 Floor screeds........................................................................................................................ 26.80 29.60 33.10 36.10 42.20 48.60 57.50 11017
11018 Screed to treads and risers, strings, sides and top of upstand
kerbs, sides and bottom of channels and sinkings and the like.......................................... 29.00 32.10 35.80 38.90 45.90 53.40 62.80 11018
ROOF SCREEDS
Per square metre
11019 Screed on roofs.................................................................................................................... 29.00 32.00 35.80 38.90 45.90 53.40 62.80 11019
11020 Screed to treads and risers, strings, sides and top of upstand
kerbs, sides and bottom of channels and sinkings and the like.......................................... 31.50 34.70 35.80 42.00 49.30 57.20 67.20 11020
LEVELLING SKIM COAT
A
Per square metre $
11021 Apply resin based gypsum and cement skim coat of any thickness to level up floor before receiving rubber
and vinyl floor tiles, sheets or carpet (measured separately) ......................................................................................................................................................... 20.40 11021
11/11
11 PLASTERING AND FINISHES 11
Item Item
PROPRIETARY FLOOR SCREED SYSTEM
Average thickness (mm)
3-5 5-8 8 - 10 10 - 12
A B C D
Per square metre $ $ $ $
11022 Proprietary light duty self-levelling floor screed...................................................................................................................... 112.20 127.20 134.30 155.40 11022
11023 Proprietary medium duty self-levelling floor screed................................................................................................................ 134.60 153.20 164.60 180.60 11023
11024 Proprietary heavy duty self-levelling floor screed.................................................................................................................... 163.70 178.30 226.30 263.40 11024
11025 Proprietary super duty self-levelling floor screed..................................................................................................................... 229.50 256.10 294.70 329.30 11025
11026 Proprietary light duty floor screed (with laying to fall property)............................................................................................. 118.00 134.10 139.90 152.60 11026
11027 Proprietary medium duty floor screed (ditto)........................................................................................................................... 138.60 157.30 169.00 184.30 11027
11028 Proprietary heavy duty floor screed (ditto)............................................................................................................................... 209.80 238.30 274.30 302.20 11028
11029 Proprietary super duty floor screed (ditto)................................................................................................................................ 231.60 263.60 303.40 351.30 11029
A
Per square metre $
11030 Heavy duty mechanical scrabbling to existing surface ................................................................................................................................................................. 25.50 11030
Per linear metre
11031 Point movement joint with rubber granular based material and binder ........................................................................................................................................ 15.30 11031
PROPRIETARY WATERPROOFING PROTECTIVE SCREEDS
Proprietary waterproof protective screeding including mixing of 1 part of proprietary waterproofing and bonding styrene Supply
butadiene liquid additive, 1 part of water, 1 part of cement and 2 parts of sands including bond coat/primer all in strict and
accordance with manufacturers instructions, and wood floated or steel trowelled as required : - fix
A
Per square metre $
11032 20 mm Thick on floors ................................................................................................................................................................................................................... 75.30 11032
11033 Add to Item 11032 for each additional 5 mm or part thereof in thickness ................................................................................................................................... 11.90 11033
11034 10 mm Thick on walls, columns, vertical surfaces or top of benchings ....................................................................................................................................... 55.20 11034
11035 Add to Item 11034 for each additional 5 mm or part thereof in thickness ................................................................................................................................... 9.80 11035
11036 10 mm Thick on soffits or sloping soffits including beams and the like ...................................................................................................................................... 62.00 11036
11037 Add to Item 11036 for each additional 5 mm or part thereof in thickness ................................................................................................................................... 9.80 11037
11/12
11 PLASTERING AND FINISHES 11
Item Item
PROPRIETARY WATERPROOFING PROTECTIVE SCREEDS (CONT'D)
Proprietary prepacked polymer modified waterproof fast-setting heavy duty floor screed including bond coat/primer, all in
strict accordance with manufacturers instructions. The material is manufactured from a blend of non-shrink cements, Supply
rapid hardening fillers and waterproofing admixtures. It shall achieve a monolithic bond to cementitious substrates and will and
accept heavy traffic within two hours of placement. The compressive strength shall be greater than 40 MPa at 28 days and fix
the bond strength slant shear shall be of 22 MPa at 28 days : - A
$
Per square metre
11038 20 mm Thick on floors ................................................................................................................................................................................................................... 379.70 11038
11039 Add to Item 11038 for each additional 5 mm or part thereof in thickness ................................................................................................................................... 81.00 11039
(Note : - The above Items 11032 to 11039 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
RENDERING OR BACKING SCREEDS
Cement and sand (1:3) screed to : - 20 mm Thick 25 mm Thick
Height (mm) Height (mm)
n.e. 75 - 150 - 225 - n.e. 75 - 150 - 225 -
75 150 225 300 75 150 225 300
A B C D E F G H
Per linear metre $ $ $ $ $ $ $ $
11040 Skirting with square, splayed, rounded or rebated top edge, and
square, splayed or coved bottom ...................................................................... 22.00 24.00 26.10 28.10 23.30 25.60 27.90 30.10 11040
11041 Ditto but to open string or stepped wall string at side of stairs........................ 23.20 25.60 27.90 30.20 26.20 28.90 31.70 34.50 11041
11042 Extra over either of Items 11040 to 11041 inclusive for approved
coloured cement or pigments............................................................................ 0.40 1.20 1.70 2.30 0.50 1.20 2.00 2.60 11042
Cement and sand (1:3) or cement and granite fines (1:3) rendering to : - Thickness (mm)
10 15 20 25
A B C D
Per square metre $ $ $ $
11043 Walls, columns, vertical surfaces, top of benchings or under cupboards................................................................................ 27.20 30.60 34.30 37.60 11043
11044 Soffits or sloping soffits including beams and the like............................................................................................................ 29.60 33.20 36.80 40.20 11044
11045 Extra over either of Items 11043 to 11044 inclusive for approved admixture of waterproofing............................................ 3.20 4.00 5.10 6.20 11045
11046 Extra over either of Items 11043 to 11044 inclusive for approved coloured cement or pigments......................................... 3.30 4.70 6.10 7.10 11046
Cement and sand (1:4) or cement and granite fines (1:4) rendering to : - Thickness (mm)
10 15 20 25
A B C D
Per square metre $ $ $ $
11047 On surfaces between grounds to receive fitments (no deduction for grounds)........................................................................ 23.90 26.60 29.30 32.00 11047
11/13
11 PLASTERING AND FINISHES 11
Item Item
INTERNAL LIME PLASTER
5 mm 10 mm 5 mm
Two
first first finish-
coats
coat coat ing coat
A B C D
Per square metre $ $ $ $
11048 On walls, columns or vertical surfaces .................................................................................................................................... - 24.10 22.10 46.10 11048
11049 On soffits or sloping soffits including beams and the like ...................................................................................................... 24.00 - 28.00 52.10 11049
GYPSUM PLASTER
Mix of first coat : Browning plaster and sand (1:2) or cement and sand (1:3). Thickness (mm)
Finishing coat as G.S. Item 18.49 (ii) with smooth finish 5 mm maximum : - 5 10 13
A B C
Per square metre $ $ $
11050 On walls, columns or vertical surfaces ...................................................................................................................................................... - 40.30 - 11050
11051 On soffits or sloping soffits including beams and the like surfaces........................................................................................................... - 46.20 - 11051
11052 On walls, columns or vertical surfaces of expanded metal lathing (measured separately)....................................................................... - - 42.40 11052
11053 On soffits or sloping soffits including beams and the like, surfaces of expanded metal lathing (measured separately).......................... - - 48.20 11053
11054 On walls, columns or vertical plasterboard surfaces ................................................................................................................................. 29.90 - - 11054
11055 On soffits or sloping soffits including beams and the like, plasterboard surfaces.................................................................................... 35.80 - - 11055
MOULDING AND MOULDED CORNICES
Lime putty and paper pulp or Plaster of Paris (1:1) moulding and moulded cornices on and including Girth (mm)
rough plaster backing, all necessary bracketing, lathing, dubbing out, moulds, mitres, stops and the like, n.e. 75 - 150 - 225 -
and finishing true to details : - 75 150 225 300
A B C D
Per linear metre $ $ $ $
11056 Moulding or moulded cornice .................................................................................................................................................. 25.20 33.30 44.50 56.70 11056
11057 Ditto but circular on plan to radius n.e. 7.50 m ....................................................................................................................... 37.20 47.80 65.00 80.80 11057
11058 Preformed cornices.................................................................................................................................................................... 63.90 72.00 80.40 88.20 11058
11059 Ditto but circular on plan to radius n.e. 7.50 m........................................................................................................................ 72.30 81.50 92.30 101.60 11059
11/14
11 PLASTERING AND FINISHES 11
Item Item
ACOUSTIC AND CEMENTITIOUS FIREPROOFING PLASTER
(Note : - The following Items 11060 to 11063 inclusive will only be paid for, if ordered by the Maintenance Surveyor
in writing.)
Prepare and apply acoustic plaster in accordance with G.S. Items 18.35 and 18.56 and the minimum thickness
and coats as recommended by the manufacturer : -
A
Per square metre $
11060 On walls, columns, vertical surfaces, soffits or sloping soffits including beams and the like ..................................................................................................... 105.50 11060
Prepare and spray cementitious fireproofing plaster on the following structural steel surfaces Fire rated period
in accordance with manufacturer's recommendation : - 1 hour 2 hours 4 hours
A B C
Per square metre $ $ $
11061 Interior concealed structural steel surfaces with spray-texture finish........................................................................................................ 172.80 203.70 329.20 11061
11062 Interior exposed structural steel surfaces with spray-texture or trowelled smooth finish......................................................................... 172.80 320.20 387.10 11062
11063 Exterior exposed structural steel surfaces with spray-texture or trowelled smooth finish........................................................................ 291.10 436.60 727.70 11063
PROPRIETARY WALL PLASTER FOR SQUASH COURT
Prepare and apply proprietary plaster for squash court in accordance with the manufacturer's instruction : -
A
Per square metre $
11064 On walls, columns, vertical surfaces, soffits or sloping soffits including beams and the like ..................................................................................................... 1,303.20 11064
EXTERNAL RENDERING
Two
First Finish- coats
coat ing coat render-
ing
Thickness (mm) 10 10 20
A B C
Per square metre $ $ $
11065 On walls, columns or vertical surfaces ...................................................................................................................................................... 35.10 43.60 78.60 11065
11066 On soffits or sloping soffits including beams and the like ........................................................................................................................ 42.00 47.40 82.20 11066
11/15
11 PLASTERING AND FINISHES 11
Item Item
EXPOSED AGGREGATE RENDERING (SHANGHAI PLASTER) 20 mm Thick
Colour
Exposed aggregate rendering applied in two coats as G.S. Item 18.55 : - Dark Medium White
A B C
Per square metre $ $ $
11067 On walls, columns or vertical surfaces ...................................................................................................................................................... 76.00 78.00 87.50 11067
11068 On soffits or sloping soffits including beams and the like......................................................................................................................... 82.10 93.60 84.00 11068
GRANOLITHIC FINISH
Granolithic paving, etc., of the mix and finish required : - Mix A (Trowelled) Mix B (Trowelled)
Thickness (mm) Thickness (mm)
15 20 15 20
A B C D
Per square metre $ $ $ $
11069 On floors.................................................................................................................................................................................... 48.40 56.80 54.50 65.10 11069
11070 To treads and risers, ends of stairs, sides and top of upstand kerbs, sides and bottom of channels and
sinkings, tops, sides, soffits and edges of shelves, working slabs and the like....................................................................... 54.40 63.00 60.40 70.40 11070
11071 On walls, columns or vertical surfaces..................................................................................................................................... - 60.00 - 67.50 11071
11072 Add to either of Items 11069 to 11071 inclusive for rubbed finish ........................................................................................ 38.00 38.00 38.00 38.00 11072
11073 Extra over either of Items 11069 to 11071 inclusive for paving, etc., hardened with approved liquid hardener
and/or dust proofer.................................................................................................................................................................... 10.80 14.00 10.80 14.00 11073
11074 Extra over either of Items 11069 to 11071 inclusive for approved coloured cement or pigments......................................... 5.80 7.50 5.80 7.50 11074
Granolithic paving, etc., of the mix and finish required : - Mix C (Washed) Mix D (Washed)
Thickness (mm) Thickness (mm)
15 20 15 20
A B C D
Per square metre $ $ $ $
11075 On floors.................................................................................................................................................................................... 63.50 73.40 70.20 81.90 11075
11076 To treads and risers, ends of stairs, sides and top of upstand kerbs, sides and bottom of channels and
sinkings, tops, sides, soffits and edges of shelves, working slabs and the like ...................................................................... 71.30 81.60 78.70 90.70 11076
11077 On walls, columns or vertical surfaces..................................................................................................................................... - 77.60 - 86.40 11077
11078 Extra over either of Items 11075 to 11077 inclusive for paving, etc., hardened with approved liquid hardener
and/or dust proofer.................................................................................................................................................................... 10.60 14.00 10.60 14.00 11078
11079 Extra over either of Items 11075 to 11077 inclusive for approved coloured cement or pigments......................................... 6.70 8.40 6.70 8.40 11079
11/16
11 PLASTERING AND FINISHES 11
Item Item
GRANOLITHIC FINISH (CONT'D)
20 mm Thick 25 mm Thick
Granolithic paving, etc., of the mix and finish required : - Height (mm) Height (mm)
n.e. 75 - 150 - 225 - n.e. 75 - 150 - 225 -
75 150 225 300 75 150 225 300
A B C D E F G H
Per linear metre $ $ $ $ $ $ $ $
11080 Granolithic Mix A skirting with splayed, rounded or rebated top
edge, and square, splayed or coved bottom trowelled finish............................ 7.50 15.50 23.00 30.90 8.00 16.50 25.90 35.40 11080
11081 Granolithic Mix B ditto .................................................................................... 8.00 16.10 24.30 33.10 8.30 18.80 27.60 38.00 11081
11082 Add to either of Items 11080 to 11081 inclusive for rubbed
finish ................................................................................................................. 2.90 5.80 8.90 11.50 2.80 5.80 8.60 11.50 11082
11083 Granolithic Mix C skirting with splayed, rounded or rebated top
edge, and square, splayed or coved bottom washed finish............................... 9.80 20.80 30.90 42.80 10.50 23.00 34.60 47.80 11083
11084 Granolithic Mix D ditto..................................................................................... 10.10 21.40 31.40 45.50 10.90 24.20 36.70 50.20 11084
11085 Add to either of Items 11080 to 11081 inclusive and Items
11083 to 11084 inclusive for labour forming open string or
stepped wall string at side of stairs .................................................................. 1.10 2.00 2.90 3.90 1.10 2.00 2.80 4.00 11085
11086 Add to either of Items 11080 to 11081 inclusive and Items
11083 to 11084 inclusive for full thickness in coloured cement
or pigments ....................................................................................................... 0.50 1.40 2.10 2.90 0.70 1.40 2.40 3.30 11086
Mix A and B Mix C and D
Height (mm) Height (mm)
n.e. 75 - 150 - 225 - n.e. 75 - 150 - 225 -
75 150 225 300 75 150 225 300
A B C D E F G H
Per linear metre $ $ $ $ $ $ $ $
11087 Add to skirting of any thickness if executed in two coats with
finishing coat 10 mm thick mixed with coloured cement or
pigments............................................................................................................. 0.40 0.80 1.20 1.70 0.40 0.80 1.30 1.90 11087
11/17
11 PLASTERING AND FINISHES 11
Item Item
TERRAZZO WORK
Type A Type B Type C
(white (white (white
or or or
coloured coloured coloured
cement) cement) cement)
A B C
Per square metre $ $ $
11088 25 mm Thick on floors ............................................................................................................................................................................... 103.60 103.30 103.10 11088
11089 25 mm Thick on treads of stairs ................................................................................................................................................................. 108.00 108.00 108.00 11089
11090 15 mm Thick to risers and ends of stair, sides and top of upstand kerbs, sides and bottom of channels
and sinkings, and the like ........................................................................................................................................................................... 109.60 109.50 109.20 11090
11091 20 mm Thick on walls, columns or vertical surfaces including 1 coat of wax polish on finished surface............................................... 127.10 126.70 126.40 11091
11092 15 mm Thick to tops, sides, soffits and edges of shelves, working slabs, sinks, cills and the like .......................................................... 112.00 111.70 111.40 11092
Per linear metre
11093 20 mm Thick skirting n.e. 75 mm high with splayed, rounded or rebated top edge, and square, splayed or coved
bottom including 1 coat of wax polish on finished surface........................................................................................................................ 11.30 11.30 11.30 11093
11094 Ditto but 75 - 150 mm high ........................................................................................................................................................................ 24.50 24.40 24.40 11094
11095 Ditto but 150 - 225 mm high ...................................................................................................................................................................... 42.50 42.50 42.40 11095
11096 Ditto but 225 - 300 mm high....................................................................................................................................................................... 58.50 58.50 58.30 11096
Add to either of Items 11093 to 11096 inclusive for labour forming open string or stepped wall string at side
of stairs ....................................................................................................................................................................................................... 20% 20% 20%
11/18
11 PLASTERING AND FINISHES 11
Item Item
CERAMIC AND QUARRY FLOOR TILES
Thickness (mm)
Ceramic floor tiles and quarry floor tiles in any colour : - n.e. 9.5 exceeding 9.5
Exceed- Exceed-
Tile n.e. n.e.
ing ing
size 0.36 m 0.36 m
0.36 m 0.36 m
A B C D
Per square metre $ $ $ $
11097 Tiling on floors.......................................................................................................................................................................... 161.20 170.90 176.30 186.10 11097
11098 Ditto but to treads and risers of stairs, sides and top of upstand kerbs, sides and
bottom of channels and the like ............................................................................................................................................... 165.10 176.60 180.20 191.90 11098
11099 Extra over either of Items 11097 to 11098 inclusive for slip resistant tiles satisfying the
standard as set out in G.S. Item 18.184.................................................................................................................................... 9.50 9.50 9.50 9.50 11099
Per linear metre
11100 Extra over Item 11098 for stair tread tile.................................................................................................................................. 6.40 6.40 6.40 6.40 11100
11101 Skirting 100 mm high with rounded top edges and coved bottom.......................................................................................... 44.40 - 49.60 - 11101
11102 Ditto but 150 mm high.............................................................................................................................................................. 55.80 - 62.60 - 11102
11103 Ditto but 200 mm high.............................................................................................................................................................. 72.00 - 79.70 - 11103
Add to either of Items 11101 to 11103 inclusive for labour forming open string
or stepped wall string at side of stairs....................................................................................................................................... 20% - 20% -
Per square metre
11104 Lay only tiling on floors............................................................................................................................................................ 65.50 71.40 65.50 71.40 11104
11105 Lay only tiling to treads and risers of stairs, sides and top of upstand kerbs, sides
and bottom of channels and the like......................................................................................................................................... 69.40 77.20 69.40 77.20 11105
11106 Rake out joints between tiles and point in natural or coloured cement and sand
grout on existing tiled surface................................................................................................................................................... 29.50 28.20 29.50 28.20 11106
11107 Hack out and replace tiling on floor in isolated patches and
point to match existing.............................................................................................................................................................. 172.70 182.50 187.80 197.60 11107
Add to either of Items 11097 to 11098 inclusive, Items 11101 to 11103 inclusive and Item 11107 for
ceramic and quarry floor tiles of specific quality........................................................................................................................................................................... 65%
11/19
11 PLASTERING AND FINISHES 11
Item Item
CONCRETE FLOOR TILES
30 mm thick (maximum)
Concrete floor tiles to BS 1197 in any colour and size : - Finish Concrete Granolithic
Exceed- Exceed-
Tile n.e. n.e.
ing ing
Size 0.05 m 0.05 m
0.05 m 0.05 m
A B C D
Per square metre $ $ $ $
11108 Tiling on floors.......................................................................................................................................................................... 118.80 85.00 190.60 162.90 11108
11109 Tiling to treads and risers of stairs, sides and top of upstand kerbs, sides and bottom of channels
and the like ............................................................................................................................................................................... 125.80 90.20 198.10 166.70 11109
Per linear metre
11110 Extra over for tile with rounded edge....................................................................................................................................... 9.30 13.10 7.70 9.40 11110
11111 Skirting 100 mm high with rounded top edges and coved bottom.......................................................................................... 33.00 35.20 44.10 46.90 11111
11112 Ditto but 150 mm high.............................................................................................................................................................. 47.50 50.30 64.10 68.20 11112
11113 Ditto but 200 mm high.............................................................................................................................................................. 61.10 63.50 82.10 86.20 11113
Add to either of Items 11111 to 11113 inclusive for labour forming open string or stepped wall
string at side of stairs................................................................................................................................................................ 20% 20% 20% 20%
Per square metre
11114 Lay only tiling on floors............................................................................................................................................................ 43.70 31.00 43.70 31.00 11114
11115 Lay only tiling to treads and risers of stairs, sides and top of upstand kerbs, sides and bottom
of channels and the like ............................................................................................................................................................ 49.50 34.90 49.50 34.90 11115
TERRAZZO FLOOR TILES
Terrazzo floor tiles to BS EN 13748 in any size, colour and surface finish : - Thickness (mm)
20 30
A B
Per square metre $ $
11116 Tiling on floors.............................................................................................................................................................................................................. 147.20 166.10 11116
11117 Tiling to treads and risers of stairs, sides and top of upstand kerbs, sides and bottom of channels and the like ...................................................... 154.10 175.50 11117
Per linear metre
11118 Extra over Item 11117 for stair tread tile...................................................................................................................................................................... 20.80 21.90 11118
11119 Skirting 100 mm high with rounded top edges and coved bottom.............................................................................................................................. 38.70 43.20 11119
11120 Ditto but 150 mm high.................................................................................................................................................................................................. 50.00 55.50 11120
11121 Ditto but 200 mm high.................................................................................................................................................................................................. 63.10 68.90 11121
Add to either of Items 11119 to 11121 inclusive for labour forming open string or stepped wall string at side of stairs......................................... 20% 20%
11/20
11 PLASTERING AND FINISHES 11
Item Item
TERRAZZO FLOOR TILES (CONT'D)
Terrazzo floor tiles to BS EN 13748 in any size, colour and surface finish : - (Cont'd) Thickness (mm)
20 30
A B
Per square metre $ $
11122 Lay only tiling on floors................................................................................................................................................................................................ 43.10 49.00 11122
11123 Lay only tiling to treads and risers of stairs, sides and top of upstand kerbs, sides and bottom of channels and the like ......................................... 49.90 56.80 11123
11124 Hack out and replace tiling on floor in isolated patches and point to match existing................................................................................................. 152.20 174.40 11124
CORK TILING
Cork tiles of any size laid and fixed with adhesive including cleaning down and polishing with wax emulsion : - Thickness (mm)
6 9 12
A B C
Per square metre $ $ $
11125 Tiling on floors............................................................................................................................................................................................ 107.10 146.10 179.70 11125
11126 Tiling to walls, columns and vertical surfaces........................................................................................................................................... 108.70 147.70 181.30 11126
11127 Tiling to ceilings ......................................................................................................................................................................................... 110.20 149.40 182.90 11127
11128 Lay only tiling on floors.............................................................................................................................................................................. 32.60 32.60 32.60 11128
11129 Ditto to walls, columns and vertical surfaces............................................................................................................................................. 33.60 33.60 33.60 11129
11130 Ditto to ceilings........................................................................................................................................................................................... 35.60 35.60 35.60 11130
11/21
11 PLASTERING AND FINISHES 11
Item Item
FLEXIBLE TILES OR SHEET FINISHES
Supply and lay flexible tiles as G.S. Items 18.130, 18.131 and 18.134 in any colour and patterns : - Thickness (mm)
2.5 2 3.2
Semi- Unbacked
Lino-
flexible flexible
leum
p.v.c. vinyl tiles
tiles tiles
A B C
Per square metre $ $ $
11131 Tiling on floors............................................................................................................................................................................................ 134.60 111.70 189.20 11131
11132 Tiling to treads and risers of stairs.............................................................................................................................................................. 144.40 119.80 199.10 11132
11133 Lay only tiling on floors.............................................................................................................................................................................. 36.30 36.30 36.30 11133
11134 Lay only tiling to treads and risers of stairs................................................................................................................................................ 41.20 41.20 41.20 11134
Supply and lay flexible sheet as G.S. Items 18.132 to 18.134 in any colour and patterns : - Overall thickness (mm)
1.2 2 3 3.2 4.5
Un- Un- Foam
backed backed backed Lino- Lino-
flexible flexible (1.5 mm leum leum
vinyl vinyl thick) sheet sheet
sheet sheet vinyl sheet
A B C D E
Per square metre $ $ $ $ $
11135 Sheeting on floors.................................................................................................................................................... - 171.00 179.90 288.20 378.40 11135
11136 Sheeting to treads and risers of stairs...................................................................................................................... - 182.20 192.30 305.20 400.30 11136
11137 Sheeting to walls..................................................................................................................................................... 160.10 - - - - 11137
11138 Lay only sheeting on floors..................................................................................................................................... - 49.90 49.90 53.80 61.60 11138
11139 Lay only sheeting to treads and risers of stairs....................................................................................................... - 55.80 55.80 59.70 71.40 11139
11140 Lay only sheeting to walls....................................................................................................................................... 74.30 - - - - 11140
11/22
11 PLASTERING AND FINISHES 11
Item Item
FLEXIBLE TILES OR SHEET FINISHES (CONT'D) Vinyl Vinyl
tiles sheet
Supply and lay in any colour and patterns : - 2 mm 2 mm
thick thick
A B
Per square metre $ $
11141 Homogeneous vinyl flooring, heavy contact calendered and pressed sheet, fully flexible with PU reinforcement................................................... 145.50 194.70 11141
11142 Antistatic homogeneous vinyl flooring with acid resisting property, electrical resistance : 10 4 ohms to 10 6 ohms............................................................
240.10 275.60 11142
11143 Antistatic homogeneous vinyl flooring with acid resisting property, electrical resistance : 10 4 ohms to 10 6 ohms
including all necessary copper strip or other conductive media.................................................................................................................................. 269.20 360.20 11143
11144 Antistatic homogeneous vinyl safety flooring in sheet form, patterned co-ordinated with clean surface treatment,
abrasion and slip resistance including cross-linked polyurethane reinforcement....................................................................................................... - 498.40 11144
(Note : - The above Items 11141 to 11144 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
A
Per linear metre $
11145 Preformed flexible P.V.C. skirting 100 mm high coved bottom and rounded or bevelled at top edge........................................................................................ 49.70 11145
11146 'L' shape PVC skirting of size 100 x 45 x 2 mm thick.................................................................................................................................................................. 48.50 11146
11147 Cove former and capping strip for vinyl roll-up skirting............................................................................................................................................................... 78.20 11147
11148 Vinyl heavy duty safety roll-up skirting......................................................................................................................................................................................... 69.20 11148
11149 PVC stair nosing 75 x 34 mm......................................................................................................................................................................................................... 84.20 11149
Per square metre
11150 Take up loose tiles of any description and size, clean back of tiles, prepare bed for and re-lay tiles, in plain or in patterns,
with approved mastic or adhesive to match existing and wax polish to an approved finish......................................................................................................... 43.10 11150
11151 Ditto but sheeting on floors............................................................................................................................................................................................................. 58.70 11151
11152 Ditto but sheeting to walls.............................................................................................................................................................................................................. 86.90 11152
11153 Scrub, clean and apply two coats wax polish with machine buffed on floors............................................................................................................................... 6.80 11153
11154 Scrub, clean and apply sealer and two coats machine applied polish on floors............................................................................................................................ 8.70 11154
Per linear metre
11155 Take up loose skirting of any description and size, clean back of skirting, prepare bed for and re-fix skirting
with approved mastic or adhesive to match existing and wax polish to an approved finish ........................................................................................................ 5.10 11155
11/23
11 PLASTERING AND FINISHES 11
Item Item
RUBBER TILES AND SHEET Thickness (mm)
4 4
Supply and lay as G.S. Item 18.135 in any size, colour and patterns : - tiles sheet
A B
Per square metre $ $
11156 Tiling/Sheeting on floors.............................................................................................................................................................................................. 352.90 409.90 11156
11157 Tiling/Sheeting to treads and risers of stairs................................................................................................................................................................ 374.40 435.10 11157
11158 Lay only tiling/sheeting on floors................................................................................................................................................................................. 29.70 48.20 11158
11159 Lay only tiling/sheeting to treads and risers of stairs................................................................................................................................................... 34.60 56.00 11159
A
Per square metre $
11160 Take up loose tiles of any description and size, clean back of tiles, prepare bed for and re-lay tiles, in plain or in
patterns, with approved mastic or adhesive to match existing and wax polish to an approved finish.......................................................................................... 36.30 11160
11161 Ditto but sheeting on floors............................................................................................................................................................................................................. 48.90 11161
11162 Scrub, clean and apply two coats wax polish with machine buffed on floors............................................................................................................................... 6.80 11162
11163 Scrub, clean and apply sealer and two coats machine applied polish on floors............................................................................................................................ 7.50 11163
MOSAIC FLOOR AND WALL TILES
Supply and lay as G.S. Item 18.110 but of any colour, size and surface finish : - Glazed Unglazed
Glass
ceramic vitreous
mosaic
mosaic mosaic
tile
tile tile
A B C
Per square metre $ $ $
11164 Tiling on floors............................................................................................................................................................................................ 120.70 141.10 147.30 11164
11165 Tiling on walls or columns.......................................................................................................................................................................... 120.80 144.10 155.90 11165
11166 Tiling to treads and risers, return ends, sides and top of upstand kerbs, sides and bottom of channels
and sinkings, surfaces of fitments, working benches and the like ............................................................................................................ 129.80 154.20 164.60 11166
Per linear metre
11167 Extra over for setting one row of tiles on splay at internal angle or junction of floor and wall tiling and the like................................... 3.20 3.20 3.20 11167
11168 Skirting n.e. 75 mm high, with square top edge and square or splay bottom edge................................................................................... 8.70 9.60 9.90 11168
11169 Ditto but 75 - 150 mm high......................................................................................................................................................................... 13.40 16.00 17.10 11169
11170 Ditto but 150 - 225 mm high....................................................................................................................................................................... 18.10 22.40 24.30 11170
11171 Ditto but 225 - 300 mm high....................................................................................................................................................................... 22.70 28.80 31.50 11171
Add to either of Items 11168 to 11171 inclusive for labour forming open string or stepped wall string
at side of stairs............................................................................................................................................................................................. 20% 20% 20%
11/24
11 PLASTERING AND FINISHES 11
Item Item
MOSAIC FLOOR AND WALL TILES (CONT'D)
Glazed Unglazed
Glass
Supply and lay as G.S. Item 18.110 but of any colour, size and surface finish : - (Cont'd) ceramic vitreous
mosaic
mosaic mosaic
tile
tile tile
A B C
Per square metre $ $ $
11172 Lay only tiling on floors.............................................................................................................................................................................. 40.20 40.20 40.20 11172
11173 Lay only tiling on walls or columns............................................................................................................................................................ 43.10 43.10 43.10 11173
11174 Lay only tiling to treads and risers, end of stairs, sides and top of upstand kerbs, sides and bottom of channels
and sinkings, surfaces of fitment, working slabs and the like ................................................................................................................... 47.00 47.00 47.00 11174
11175 Rake out joints between tiles and point in natural or coloured cement and sand grout on existing tiled surface ................................... 40.50 40.50 40.50 11175
CERAMIC WALL TILES
Ceramic wall tiles in any colour and surface finish : - Thickness (mm)
n.e. 9.5 exceeding 9.5
Exceed- Exceed-
Tile n.e. n.e.
ing ing
size 0.05 m 0.05 m
0.05 m 0.05 m
A B C D
Per square metre $ $ $ $
11176 Tiling on walls, columns, cills, top and edges of slabs, surfaces of fitment and the like........................................................ 148.10 142.20 166.30 160.40 11176
11177 Lay only tiling on walls, columns, cills, top edges of slabs and the like................................................................................. 56.80 50.90 56.80 50.90 11177
11178 Rake out joints between tiles and point in natural or coloured cement and sand grout
on existing tiled surface ........................................................................................................................................................... 31.80 29.50 31.80 29.50 11178
11179 Hack out and replace tile in isolated patches and point to match existing.............................................................................. 159.60 153.70 177.80 171.90 11179
Add to either of Items 11176 and 11179 for ceramic wall tiles of specific quality...................................................................................................................... 65%
11/25
11 PLASTERING AND FINISHES 11
Item Item
SWIMMING POOL TILES
Approved glazed ceramic swimming pool tiles of non-decaying and corrosion-proof, resistant to aggressive water Supply Fix
treated with chlorine and ozone, cleaning agents and disinfectants and slip resistant complying with DIN 51097, and only
in any size, colour, surface finish and thickness, all in accordance with the Specification : - fix
A B
Per square metre $ $
11180 Pool wall tiles; laid in pattern....................................................................................................................................................................................... 354.60 65.50 11180
11181 Pool floor tiles............................................................................................................................................................................................................... 346.80 57.70 11181
11182 Ditto; sloping................................................................................................................................................................................................................. 391.60 59.60 11182
11183 Pool tiles to steps, reveal, sides and soffit of recess..................................................................................................................................................... 398.10 74.30 11183
Per linear metre
11184 Extra over Item 11180 for pool edging tile with safety marking................................................................................................................................. 216.30 - 11184
11185 Extra over Item 11180 for pool edging tile with grooved and safety marking............................................................................................................ 376.00 - 11185
11186 Extra over Item 11180 for tile with coved bottom between sides and bottom of swimming pool.............................................................................. 224.10 - 11186
11187 Extra over Item 11180 for tile with coved bottom between sides and bottom of overflow channel........................................................................... 212.40 - 11187
11188 Extra over Item 11180 for corner tiles.......................................................................................................................................................................... 265.50 - 11188
11189 Coved skirting tiles in any size, colour and thickness.................................................................................................................................................. 120.40 - 11189
11190 Nosing tiles with embossed surface and finger grip in any size, colour and thickness............................................................................................... 99.00 - 11190
11191 Overflow channel in any size, colour and thickness.................................................................................................................................................... 1,414.50 - 11191
11192 PVC channel grating of any size, colour and thickness............................................................................................................................................... 245.00 - 11192
11193 Ditto but including stainless steel wire......................................................................................................................................................................... 359.60 - 11193
Each
11194 Add to Item 11191 for overflow channel with drainage outlet of any size.................................................................................................................. 502.70 - 11194
11195 Lane/depth marker tiles in any size, colour and thickness........................................................................................................................................... 500.70 - 11195
11196 Ditto but with factory-moulded marker........................................................................................................................................................................ 189.00 - 11196
Per pair
11197 Overflow channel internal angle .................................................................................................................................................................................. 778.40 - 11197
11198 Pool edging tile internal angle with safety marking..................................................................................................................................................... 253.30 - 11198
A
Per square metre $
11199 Rake out joints between tiles and point in approved grouting material on existing tiled surfaces............................................................................................... 46.00 11199
11/26
11 PLASTERING AND FINISHES 11
Item Item
MOVEMENT JOINTS TO TILING ON SWIMMING POOL AND POOL DECK
Prepare and apply proprietary one part medium modulus sealant based on hybrid silyl modified polyether technology to form a tough,
highly durable and water resistant elastomer suitable for intermittent and permanent immersion in potable water complying with the
following including priming surfaces with proprietary primer before applying sealant; all in strict compliance with the manufacturer's
recommendations :
Form Smooth, non-slumping paste
Colour White / Grey / Black / Portland / Buff / Rustic Red / Brown
Movement accommodation 25% butt joints
factor 50% lap joints
Skinning time at 20/50% RH 30 minutes
Cure rate at 20/50% RH 24 hours
48 hours
72 hours
Application temperature 50to 50
Service temperature Dry
Wet
Hardness shore 'A' 20 32
Standard compliance ISO 11600 Type F 25HM
DWI Water Quality Regulations 25(1)(b) - Products having a small surface
area in contact with water for public supply
BS 6920:Part 1:2000 - Water Regulations Advisory Service
ASTM C920 Class 25, Type NS, NT, G
Performance criteria of BS 4254(1991)
Chemical resistance Resistant to occasional spillage of many chemicals subject to the following
limitations :
(a) should not be applied at temperatures below 5
(b) not suitable for contact with bituminous materials
(c) must be fully cured prior to immersion in water
(d) should not be considered a substitute for a good standard of joint
preparation
(e) chlorine concentrations should be less than 10 mg/litre
Biological resistance Resistant to aerobic and anaerobic conditions evaluated in microbiologically
active situations
UV resistance Excellent
Joint size (mm)
5 x 20 5 x 25 15 x 20 15 x 25 15 x 50 25 x 25 25 x 50
A B C D E F G
Per linear metre $ $ $ $ $ $ $
11200 Proprietary sealant to movement joints in tiling on swimming pool
and pool deck including priming surfaces with proprietary primer
before applying sealant ....................................................................................................... 14.70 17.10 32.10 36.40 74.40 62.90 120.20 11200
11/27
11 PLASTERING AND FINISHES 11
Item Item
PRECAST CONCRETE PAVING SLAB OR BLOCK Supply Lay
and only
Precast concrete paving slabs (1:2:4) in any size, colour and surface finish, rectangular or irregular shape : - lay
A B
Per square metre $ $
11201 Slab 50 mm thick.......................................................................................................................................................................................................... 100.60 21.70 11201
Precast concrete blocks laid in stretcher bond, basket weave, herring bone patterns or any mixed colour Supply
patterns including all necessary cutting and trimming edges with cement and pouring sand to joints : - and lay
Lay
Block thickness
only
(mm)
60 80
A B C
Per square metre $ $ $
11202 200 x 100 mm Natural grey colour rectangular blocks.............................................................................................................................. 114.30 130.60 41.20 11202
11203 200 x 100 mm Red, brown, yellow or charcoal colour rectangular blocks................................................................................................ 115.60 132.90 41.20 11203
11204 225 x 112.50 mm Natural grey colour interlocking blocks........................................................................................................................ 74.70 90.80 41.20 11204
11205 225 x 112.50 mm Red, brown, yellow or charcoal colour interlocking blocks......................................................................................... 79.10 89.20 41.20 11205
RE-CONSTITUTED ARTIFICIAL GRANITE WALL AND FLOOR TILING
Re-constituted artificial granite tiles in any colour and surface finish : - Square/
Strip tile
rectangular tile
10 - 15 mm thick 12 - 18 mm thick
Exceed- Exceed-
Tile n.e. n.e.
ing ing
size 0.01 m 0.01 m
0.01 m 0.01 m
A B C D
Per square metre $ $ $ $
11206 Tiling on floors.......................................................................................................................................................................... 191.00 161.70 187.10 166.60 11206
11207 Tiling on walls or columns........................................................................................................................................................ 196.80 170.50 192.90 176.30 11207
11208 Tiling to treads and risers, return ends, sides and top of upstand kerbs, sides and bottom of
channels and sinkings, surface of fitment, working benches and the like............................................................................... 200.70 168.50 196.80 173.40 11208
Per linear metre
11209 Extra over for corner tiles.......................................................................................................................................................... 14.80 13.30 60.30 55.90 11209
Thickness (mm)
n.e. 10 10-15 15-20
A B C
Per linear metre $ $ $
11210 Re-constituted artificial granite door threshold, n.e. 70mm wide, with bevelled edges........................................................................... 83.40 100.10 116.70 11210
Add to either of Items 11206 to 11208 inclusive and Item 11210 for re-constituted artificial granite tiles of specific quality.................................................. 65%
11/28
11 PLASTERING AND FINISHES 11
Item Item
RE-CONSTITUTED ARTIFICIAL GRANITE WALL AND FLOOR TILING
(CONT'D) Square/
Strip tile
rectangular tile
Re-constituted artificial granite tiles in any colour and surface finish : - (Cont'd) 10 - 15 mm thick 12 - 18 mm thick
Exceed- Exceed-
Tile n.e. n.e.
ing ing
Size 0.01 m 0.01 m
0.01 m 0.01 m
A B C D
Per square metre $ $ $ $
11211 Lay only tiling on floor.............................................................................................................................................................. 66.50 50.90 66.50 50.90 11211
11212 Lay only tiling on walls or columns.......................................................................................................................................... 72.30 59.70 72.30 59.70 11212
11213 Lay only tiling to treads and risers, end of stairs, sides and top of upstand kerbs, sides and
bottom of channels and sinkings, surfaces of fitment, working slabs and the like.................................................................. 76.20 57.70 76.20 57.70 11213
11214 Rake out joints between tiles and point in natural or coloured cement and sand grout on
existing tiled surface.................................................................................................................................................................. 22.40 16.60 22.40 16.60 11214
11215 Hack out and replace tile in isolated patches and point to match existing.............................................................................. 210.90 176.40 206.60 179.20 11215
Add to Item 11215 for re-constituted artificial granite tiles of specific quality............................................................................................................................ 65%
CLAY / BRICK PAVERS
Clay/ brick pavers in any size and colour, laid in stretcher bond, basket weave, Thickness (mm)
herring bone patterns : - 43 50 55 60 65 76
A B C D E F
Per square metre $ $ $ $ $ $
11216 Clay/brick pavers on floor..................................................................................................................... 160.70 172.80 187.90 201.60 215.20 244.60 11216
11217 Lay only pavers on floor........................................................................................................................ 35.30 37.30 38.20 39.20 40.20 41.20 11217
Add to Item 11216 for one layer of geogrid reinforcement of 50 KN/m strength
and grid size of 25.4 x 25.4 mm underneath sand/sand and cement bedding of
clay/brick paver as detailed on drawing No. H5136 and 5137 (Payment will only
be paid for this item, if ordered by the Maintenance Surveyor in writing.)......................................... 12% 12% 11% 10% 9% 8%
A
Per linear metre $
11218 232 x 115 x 76 mm Kerb brick on sand bed.................................................................................................................................................................................. 45.90 11218
11219 232 x 115 x 76 mm Kerb brick on mortar...................................................................................................................................................................................... 48.60 11219
11/29
11 PLASTERING AND FINISHES 11
Item Item
STONE SLABS/TILES
Tiles Slabs
Natural marble or granite slabs/tiles in any size, shape, Thickness Thickness (mm)
pattern and colour : - (mm)
8-12 20 25 32 40 50 75 100
A B C D E F G H
Per square metre $ $ $ $ $ $ $ $
11220 Marble slabs/tiles, polished/flamed surface laid on floors............................... 237.90 389.40 471.20 548.50 610.80 652.70 774.50 938.10 11220
11221 Marble slabs/tiles, polished/flamed surface fixed on walls,
columns or vertical surfaces.............................................................................. 344.70 478.40 540.40 620.90 744.30 - - - 11221
11222 Marble slabs/tiles, polished/flamed surface laid to treads and risers,
steps, return ends, top and sides of counters, cills, door or window
jambs and heads, bands, string courses, copings, arches and
the like including all necessary cutting and forming holes............................... 305.10 455.10 479.30 566.00 628.30 - - - 11222
11223 Granite slabs/tiles, polished/flamed surface laid on floors............................... 233.90 371.30 447.90 548.50 610.80 652.70 737.40 938.10 11223
11224 Granite slabs/tiles, fine hammered dressed surface laid on floors................... 274.30 443.00 458.30 551.30 614.20 666.90 759.00 959.40 11224
11225 Granite slabs/tiles, polished/flamed surface fixed on walls,
columns or vertical surfaces.............................................................................. 439.90 584.50 600.10 682.00 744.30 - - - 11225
11226 Granite slabs/tiles, fine hammer dressed surface fixed on walls,
columns or vertical surfaces.............................................................................. 520.20 584.50 600.10 682.00 744.30 - - - 11226
11227 Granite slabs/tiles, polished/flamed surface laid to treads
and risers, steps, return ends, top and sides of counters, cills,
door or window jambs and heads, bands, string courses,
copings, arches and the like including all necessary cutting
and forming holes.............................................................................................. 332.20 541.60 557.20 643.90 706.30 - - - 11227
11228 Granite slabs/tiles, fine hammered dressed surface laid to treads
and risers, return ends, top and sides of counters, cills, door
or window jambs and heads, bands, string courses, copings,
arches and the like including all necessary cutting and
forming holes..................................................................................................... 381.10 541.60 557.20 643.90 706.30 - - - 11228
Thickness (mm)
20-30 30-40 40-50 50-75 75-100
A B C D E
Per linear metre $ $ $ $ $
11229 Marble/granite mouldings, polished/flamed surface n.e. 100 mm wide................................................................ 67.80 76.00 81.80 96.50 116.90 11229
11230 Ditto but 100 - 200 mm wide.................................................................................................................................. 120.00 135.40 146.10 174.40 213.40 11230
11/30
11 PLASTERING AND FINISHES 11
Item Item
STONE SLABS/TILES (CONT'D)
Thickness (mm)
Natural marble or granite slabs/tiles in any size, shape, pattern and colour : - (Cont'd) n.e. 10 10-15 15-20
A B C
Per linear metre $ $ $
11231 Marble/granite door threshold, n.e. 70mm wide, with bevelled edges...................................................................................................... 155.90 167.60 175.40 11231
Add to either Items 11220 to 11231 inclusive for natural marble or granite of European origin................................................................................................. 40%
Marble /
Granite Marble/Granite slabs
tiles
Thickness
Thickness (mm)
(mm)
8-12 20-30 30-40 40-50 50-75 75-100
Per square metre A B C D E F
$ $ $ $ $ $
11232 Lay only slabs/tiles on floors................................................................................................................. 53.80 64.50 67.50 70.40 75.30 83.10 11232
11233 Fix/lay only slabs/tiles to walls, columns or vertical surfaces.............................................................. 163.00 197.10 201.00 - - - 11233
11234 Ditto but including metal support backing frame................................................................................. - 631.50 681.20 - - - 11234
11235 Lay only slabs/tiles to treads and risers, steps, return ends, top and sides of counters,
cills, door or window jambs and heads, bands, string courses, copings, arches and the
like including all necessary cutting and forming holes........................................................................ 63.60 76.20 85.00 - - - 11235
Thickness (mm)
20-30 30-40 40-50 50-75 75-100
A B C D E
Per linear metre $ $ $ $ $
11236 Lay only moulding n.e. 100 mm wide..................................................................................................................... 21.70 23.60 25.60 28.50 33.40 11236
11237 Lay only moulding 100 - 200 mm wide.................................................................................................................. 25.60 28.50 31.40 36.30 44.10 11237
11/31
11 PLASTERING AND FINISHES 11
Item Item
RESIN STONE SLAB
Resin stone slabs 13 mm thick, in any size, shape, pattern and colour including forming splayed edges and polishing : -
A
Per square metre $
11238 Slabs on floors................................................................................................................................................................................................................................. 436.60 11238
11239 Slabs on walls, columns or vertical surfaces.................................................................................................................................................................................. 451.10 11239
11240 Slabs to treads and risers, steps, return ends, end of stairs, top and sides of counters, cills, door or window jambs and heads,
bands, string courses, copings, arches and the like including all necessary cutting and forming holes....................................................................................... 453.00 11240
11241 Lay only slabs on floors ................................................................................................................................................................................................................. 57.70 11241
11242 Fix only slabs on walls, columns or vertical surfaces.................................................................................................................................................................... 177.60 11242
11243 Lay only tiling to treads and risers, steps, return ends, end of stairs, top and sides of counters, cills, door or window jambs
and heads, bands, string courses, copings, arches and the like including all necessary cutting and forming holes
cutting and forming holes ......................................................................................................................................................................................................................................
65.50 11243
SUNDRY PAVING, ETC.
A
Per square metre $
11244 Pebble finish 20 mm thick Mix "A" comprising cement, sand and pebble (2:2:3) laid on floor with washed finish.................................................................. 122.20 11244
11245 Pebble finish 20 mm thick Mix "B" comprising cement and pebble (2:3) rendering to vertical surfaces with washed finish.................................................... 154.40 11245
11246 Pebble paving formed with selected pebbles exceeding 25 mm but n.e. 75 mm gauge, pressed into top of concrete bed (measured
separately) before setting to give roughly level surfaces, including neatly recess pointing between pebbles in cement and sand
(1:3) grout ....................................................................................................................................................................................................................................................
245.00 11246
11247 Small stone paving formed with selected stones exceeding 25 mm but n.e. 100 mm gauge, pressed into top of concrete bed
(measured separately) before setting to give roughly level surfaces, including dressing off top of stones after setting to give
roughly level surfaces and neatly recess pointing between stones in cement and sand (1:3) grout ............................................................................................. 298.10 11247
11248 Silicone carbide non-slip grains sprinkled on and lightly trowelled into surface of paving before setting, at a rate of 0.50 kg/m
paving.............................................................................................................................................................................................................................................. 37.30 11248
11249 Ditto but at rate of 1 kg/m paving ................................................................................................................................................................................................. 74.40 11249
Per linear metre
11250 15 x 25 mm Non-slip insert strips bedded in paving, stair treads or steps as G.S. Item 18.88..................................................................................................... 24.30 11250
11251 75 x 150 x 10 mm Plain vitreous clay or quarry non-slip nosing tiles with grooves or raisings on top surface, bedded, jointed
and pointed in cement and sand (1:3) grout ................................................................................................................................................................................. 23.40 11251
11252 Non-ferrous metal nosing angle fixed to stair and step treads....................................................................................................................................................... 52.80 11252
11/32
11 PLASTERING AND FINISHES 11
Item Item
TACTILES
Take Take
Rubber/PVC tactiles with adhesive in any pattern, colour, size and thickness, all in strict accordance Supply down down Fix
with manufacturer's instructions : - and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
11253 Rubber/plastic tactiles for indoor use....................................................................................................................................... 319.10 8.30 10.90 50.20 11253
11254 Rubber/plastic tactiles for outdoor use..................................................................................................................................... 321.30 9.60 10.90 55.00 11254
Concrete block tactiles with cement and sand slurry in any pattern, colour, size and thickness, all
in strict accordance with manufacturer's instructions : -
Per square metre
11255 Concrete block tactiles ............................................................................................................................................................. 243.60 10.90 14.70 50.20 11255
11256 Synthetic rubber tactiles with concrete base............................................................................................................................. 1,065.40 12.80 16.00 55.00 11256
Ceramic or quarry tile tactiles with cement and sand slurry in any pattern, colour, size and
thickness, all in strict accordance with manufacturer's instructions : -
Per square metre
11257 Ceramic or quarry tile tactiles................................................................................................................................................... 256.20 11.50 14.70 74.50 11257
Artificial granite tactiles with cement and sand slurry in any pattern, colour, size and thickness,
all in strict accordance with manufacturer's instructions : -
Per square metre
11258 Artificial granite tactiles............................................................................................................................................................ 654.00 16.00 22.30 79.40 11258
Supply and fix stainless steel tactile marker grade 316 with studs or strips with or without plastic
cover fixed with adhesive, fixing bolts and nuts including drilling, cut holes, make good and all
necessary fixing accessories, lay in any pattern and all in strict accordance with the
manufacturer's instructions: -
Each
11259 23mm dia. x 5mm (positional)................................................................................................................................................. 7.80 0.30 0.60 1.20 11259
11260 35mm dia. x 5mm (hazard warning tile).................................................................................................................................. 8.30 0.30 0.60 1.20 11260
11261 34mm x 285mm x 5mm (directional)...................................................................................................................................... 60.80 1.00 1.90 7.80 11261
11/33
11 PLASTERING AND FINISHES 11
Item Item
TACTILES (CONT'D)
Take Take
Supply and fix proprietary POM tactile guide path, with or without studs, fixed with adhesive Supply down down Fix
and including drilling, cut holes, make good and all necessary fixing accessories, lay in any and and and set only
pattern and all in strict accordance with the manufacturer's instructions : - fix clear aside for
away re-use
A B C D
Each $ $ $ $
11262 23mm Diameter x 5mm (positional)......................................................................................................................................... 5.10 0.30 0.60 1.20 11262
11263 35mm Diameter x 5mm (hazard warning tile).......................................................................................................................... 5.80 0.30 0.60 1.20 11263
11264 34mm Diameter x 285mm x 5mm (directional)....................................................................................................................... 40.00 1.00 1.90 7.80 11264
DIVISION STRIPS 3 mm thick
Depth Plastic Stainless steel Brass
(mm) 20 25 40 20 25 40 20 25 40
A B C D E F G H I
Per linear metre $ $ $ $ $ $ $ $ $
11265 Division strips set between different floor or
wall finishes..................................................................................... 6.30 6.90 7.90 14.80 17.20 23.10 17.20 20.40 28.40 11265
SUSPENDED CEILING SYSTEM FOR ACOUSTIC CEILING TILES; SUSPENSION
SYSTEM (GRIDS) ONLY Fit for square
or rectangular
Suspension system as G.S. Items 13.23 and 13.45 : - Tile size (m) n.e. 0.36 exc. 0.36
A B
Per square metre $ $
11266 Galvanised mild steel suspension system..................................................................................................................................................................... 53.80 57.60 11266
11267 Aluminium suspension system..................................................................................................................................................................................... 53.50 56.40 11267
11268 Composite galvanised mild steel and aluminium suspension system.......................................................................................................................... 53.50 50.60 11268
Add to either of Items 11266 to 11268 inclusive for suspension system suitable for foam tape or sealing mastic................................................... 15% 15%
11269 Fix only suspension system of any type........................................................................................................................................................................ 24.40 24.40 11269
11270 Take down and clear away suspension system of any type.......................................................................................................................................... 9.60 9.60 11270
11271 Take down and set aside for re-use suspension system of any type except suspension system suitable for foam
tape or sealing mastic.................................................................................................................................................................................................... 14.70 14.70 11271
Per linear metre
11272 Extra over either of Items 11266 to 11268 inclusive for forming openings for light fittings or air grilles module size
exceeding 1.50 m long and n.e. 200 mm wide............................................................................................................................................................. 20.10 20.10 11272
Each
11273 Extra over either of Items 11266 to 11268 inclusive for forming openings for light fittings or air grilles module size
n.e. 1.50 m long............................................................................................................................................................................................................. 25.40 25.40 11273
11/34
11 PLASTERING AND FINISHES 11
Item Item
SUSPENDED CEILING SYSTEM FOR ACOUSTIC CEILING TILES; ACOUSTIC CEILING
TILES ONLY
Tile size (m)
Acoustic ceiling tiles in any thickness as G.S. Item 13.22 : - n.e. 0.36 exc. 0.36
A B
Per square metre $ $
11274 Wood or other organic fibre perforated acoustic ceiling tiles fixed to soffits or walls................................................................................................ 70.20 72.20 11274
11275 Ditto but fixed to suspension system (measured separately)....................................................................................................................................... 67.50 68.60 11275
11276 Mineral fibre/rock wool acoustic tiles with fissured design tiles fixed to soffits or walls.......................................................................................... 96.20 99.50 11276
11277 Ditto but fixed to suspension system (measured separately)....................................................................................................................................... 93.30 96.60 11277
11278 Moisture resistant mineral fibre/rock wool acoustic tiles fixed to soffits or wall........................................................................................................ 117.80 129.30 11278
11279 Ditto but fixed to suspension system (measured separately)....................................................................................................................................... 114.90 126.40 11279
11280 Moisture resistant vinyl faced mineral fibre/rock wool acoustic tiles fixed to soffits or wall..................................................................................... 127.40 150.40 11280
11281 Ditto but fixing to suspension system (measured separately)...................................................................................................................................... 124.50 147.50 11281
11282 Moisture resistant hygiene acoustic tiles fixed to soffits or wall................................................................................................................................. 148.40 154.30 11282
11283 Ditto but fixed to suspension system (measured separately)....................................................................................................................................... 145.50 151.30 11283
11284 Moisture resistant metal foil faced mineral fibre/rock wool acoustic tiles fixed to soffits or wall............................................................................. 193.00 205.20 11284
11285 Ditto but fixed to suspension system (measured separately)....................................................................................................................................... 190.10 202.80 11285
11286 Moisture resistant metal foil faced bio-proof hygiene mineral fibre/rock wool acoustic tiles fixed to
suspension system (measured separately)..................................................................................................................................................................... 191.30 216.50 11286
11287 Ditto but sealed into the suspension system with low compression foam tape and/or silicone sealing mastic
(suspension system measured separately)..................................................................................................................................................................... 230.90 254.20 11287
11288 Take down and clear away acoustic ceiling tiles of any type....................................................................................................................................... 5.10 5.10 11288
11289 Take down, set aside for re-use acoustic ceiling tiles of any type (other than sealed type)........................................................................................ 15.30 15.30 11289
11290 Take down, set aside for re-use sealed acoustic ceiling tiles....................................................................................................................................... 31.30 31.30 11290
11291 Fix only ceiling tiles to soffits or wall of any type........................................................................................................................................................ 18.50 18.50 11291
11292 Fix only ceiling tiles to suspension system of any type................................................................................................................................................ 14.60 14.60 11292
11293 Fix only ceiling tiles sealed into the suspension system with low compression foam tape and/or silicone sealing
mastic............................................................................................................................................................................................................................. 39.00 39.00 11293
Each
11294 Forming openings through existing acoustic tiles (non-sealed type) for light fittings, sprinkler heads, smoke detectors, etc. in
size n.e. 0.05 m including plywood backing as required............................................................................................................................................ 6.30 6.30 11294
11295 Forming openings through existing acoustic tiles (sealed type) for light fittings, sprinkler heads, smoke detectors, etc. in size
n.e. 0.05 m including plywood backing as required and sealed into the system with low compression foam tape and/or
silicone sealing mastic.................................................................................................................................................................................................. 18.00 18.00 11295
11/35
11 PLASTERING AND FINISHES 11
Item Item
SUSPENDED CEILING SYSTEM FOR METAL CEILING; SUSPENSION SYSTEM
(GRIDS) ONLY Strip/panel
Lay-in Clip-in
Suspension system recommended by the manufacturer for approved ceiling type : - Internal Internal External
type type type
A B C
Per square metre $ $ $
11296 Galvanised mild steel suspension system .................................................................................................................................................. 81.30 86.10 103.80 11296
11297 Aluminium suspension system................................................................................................................................................................... 72.80 85.20 102.50 11297
11298 Composite galvanised mild steel and aluminium suspension system........................................................................................................ 81.60 91.70 104.50 11298
11299 Extra over either of Items 11296 to 11298 inclusive for air-tight suspension system............................................................................... 47.00 100.90 - 11299
11300 Take down and clear away suspension system of any type........................................................................................................................ 12.10 12.10 12.10 11300
11301 Take down and set aside for re-use suspension system generally.............................................................................................................. 21.70 21.70 21.70 11301
11302 Take down and set aside for re-use suspension system of air-tight type................................................................................................... 32.50 32.50 - 11302
11303 Fix only suspension system generally......................................................................................................................................................... 27.30 27.30 27.30 11303
11304 Fix only suspension system of air-tight type............................................................................................................................................... 53.60 53.60 - 11304
Per linear metre
11305 Extra over either of Items 11296 to 11298 inclusive for forming openings for light fittings or air grilles
module size exceeding 1.50 m long and n.e. 200 mm wide generally....................................................................................................... 17.90 17.90 17.90 11305
11306 Extra over either of Items 11296 to 11298 inclusive for forming openings for light fittings or air grilles
module size exceeding 1.50 m long and n.e. 200 mm wide for suspension system of air-tight type........................................................ 38.80 38.80 - 11306
Each
11307 Extra over either of Items 11296 to 11298 inclusive for forming openings for light fittings or air grilles
module size n.e. 1.50 m long for suspension system generally.................................................................................................................. 22.00 22.00 22.00 11307
11308 Extra over either of Items 11296 to 11298 inclusive for forming openings for light fittings or air grilles
module size n.e. 1.50 m long for suspension system air-tight type............................................................................................................ 89.80 89.80 - 11308
11/36
11 PLASTERING AND FINISHES 11
Item Item
SUSPENDED CEILING SYSTEMS FOR METAL CEILING; PANEL/STRIP ONLY
Non-perforated ceiling panel/strip in any thickness and colour fixed to Aluminium panel/strip G.M.S. panel/strip
suspension system in accordance with the manufacturer's instructions Lay-in Clip-in Lay-in Clip-in
(suspension system measured separately) : - Internal Internal External Internal Internal External
type type type type type type
A B C D E F
Per square metre $ $ $ $ $ $
11309 Ceiling panel/strip module size n.e. 0.36 m........................................................................................ 171.00 171.00 191.30 171.00 171.00 230.10 11309
11310 Ditto, exceeding 0.36 m....................................................................................................................... 211.10 203.80 274.10 203.80 214.90 287.50 11310
11311 Extra over either of Items 11309 to 11310 inclusive for additional sound
absorbing matts on the rear side of the panel/strip............................................................................... 34.60 34.60 34.70 34.60 34.60 34.70 11311
11312 Extra over either of Items 11309 to 11310 inclusive for air-tight panel/strip...................................... 221.60 362.80 - 213.50 - - 11312
11313 Take down and clear away ceiling panel/strip of any type................................................................... 10.90 10.90 10.90 10.90 10.90 10.90 11313
11314 Take down and clear away ceiling panel/strip of air-tight type............................................................ 26.20 26.20 - 26.20 - - 11314
11315 Take down and set aside for re-use away ceiling panel/strip generally............................................... 16.60 16.60 16.60 16.60 16.60 16.60 11315
11316 Take down and set aside for re-use away ceiling panel/strip of
any type of air-tight type........................................................................................................................ 42.10 42.10 - 42.10 - - 11316
11317 Fix only ceiling panel/strip generally.................................................................................................... 14.60 14.60 14.60 14.60 14.60 14.60 11317
11318 Fix only ceiling panel/strip of air-tight type.......................................................................................... 139.70 139.70 - 139.70 - - 11318
Per linear metre
11319 Extra over either of Items 11309 to 11310 inclusive for forming openings
for light fittings or air grilles module size exceeding 1.50 m long
and n.e. 200 mm wide for panel/strip generally................................................................................... 102.30 102.30 102.30 102.30 102.30 102.30 11319
11320 Extra over either of Items 11309 to 11310 inclusive for forming openings
for light fittings or air grilles module size exceeding 1.50 m long
and n.e. 200 mm wide for panel/strip of air-tight type......................................................................... 109.80 109.80 - 109.80 - - 11320
Each
11321 Extra over either of Items 11309 to 11310 inclusive for forming openings
for light fittings, air grilles and the like module size n.e. 1.50 m
long for panel/strip generally................................................................................................................ 62.20 62.20 62.20 62.20 62.20 62.20 11321
11322 Ditto for forming opening for sprinkler heads, smoke detectors, etc................................................... 28.80 28.80 28.80 28.80 28.80 28.80 11322
11323 Extra over either of Items 11309 to 11310 inclusive for forming openings
for light fittings, air grilles and the like module size n.e. 1.50 m
long for panel/strip of air-tight type...................................................................................................... 113.70 113.70 - 113.70 - - 11323
11324 Ditto for forming opening for sprinkler heads, smoke detectors, etc................................................... 59.10 59.10 - 59.10 - - 11324
Add to either of Items 11309 to 11310 inclusive for panel/strip of perforated
ceiling type............................................................................................................................................. 10% 10% 10% 10% 10% 10%
11/37
11 PLASTERING AND FINISHES 11
Item Item
RAISED ACCESSED FLOORING
Take Take
Raised accessed flooring in any pedestal height as G.S. Items 18.164 to 18.183 : - Supply down down
Fix
and and and set
only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
11325 Flooring with bare panel........................................................................................................................................................... 336.10 25.50 31.30 68.20 11325
11326 Flooring with high pressure laminated panel finish................................................................................................................. 462.60 25.50 31.30 68.20 11326
11327 Flooring with carpet tile finish.................................................................................................................................................. 471.20 25.50 31.30 68.20 11327
11328 Flooring with vinyl tile finish.................................................................................................................................................... 473.60 25.50 31.30 68.20 11328
11329 Access ramp............................................................................................................................................................................... 866.30 26.20 35.70 155.90 11329
11330 Steps........................................................................................................................................................................................... 1,091.50 23.60 35.70 116.90 11330
Per linear metre
11331 Standard railing......................................................................................................................................................................... 1,357.20 12.10 16.60 117.90 11331
A
Each $
11332 Set of picker and tool (lifting device)............................................................................................................................................................................................. 522.60 11332
HEAVY CONTRACT QUALITY CARPET
CARPET; FULLY ADHERING METHOD
Supply and lay carpet with all types of backing and in any series and colour finish Carpet
required : - Pile weight (kg/m)
n.e. 1.50 exc. 1.50
to floor to stairs to wall to floor to stairs to wall
A B C D E F
Per square metre $ $ $ $ $ $
11333 Carpet laid with adhesive...................................................................................................................... 124.60 141.90 166.50 175.10 187.70 209.70 11333
11334 Carpet laid with adhesive and release bond agent................................................................................ 131.60 150.20 175.00 175.00 191.40 215.00 11334
Supply and lay carpet including backing as "Environmentally Friendly Carpet" Carpet
in any series and colour finish required : - Pile weight (kg/m)
n.e. 1.00 exc. 1.00
to floor to stairs to wall to floor to stairs to wall
A B C D E F
Per square metre $ $ $ $ $ $
11335 Carpet laid with adhesive...................................................................................................................... 178.00 193.00 217.90 202.40 221.70 248.00 11335
11336 Carpet laid with adhesive and release bond agent................................................................................ 183.60 198.20 225.60 217.60 234.10 257.80 11336
11/38
11 PLASTERING AND FINISHES 11
Item Item
HEAVY CONTRACT QUALITY CARPET (CONT'D)
CARPET; FULLY ADHERING METHOD (CONT'D) Carpet
Pile density (fibre/m)
Supply and lay carpet including backing as "Environmentally Friendly Carpet" in any series and colour exc. 75 million
finish required : - (Cont'd) to floor to stairs to wall
A B C
Per square metre $ $ $
11337 Carpet laid with adhesive............................................................................................................................................................................ 224.30 240.50 260.70 11337
11338 Carpet laid with adhesive and release bond agent...................................................................................................................................... 237.20 250.00 278.30 11338
Alterations and repairs : - Carpet
to floor to stairs to wall
A B C
Per square metre $ $ $
11339 Take up and clear away existing carpet of any type................................................................................................................................... 5.70 6.90 7.50 11339
11340 Take up existing carpet of any type and set aside for re-use...................................................................................................................... 14.00 16.80 18.20 11340
11341 Lay or fix only carpet of any type with adhesive........................................................................................................................................ 19.50 29.20 32.20 11341
11342 Lay or fix only carpet of any type with adhesive and release bond agent.................................................................................................. 29.20 34.10 39.00 11342
CARPET; GRIPPER METHOD
Carpet
Supply and lay carpet with all type of backing and in any series and colour finish required : - Pile weight (kg/m)
n.e. 1.50 exc. 1.50
to floor to stairs to floor to stairs
A B C D
Per square metre $ $ $ $
11343 Carpet laid with grippers........................................................................................................................................................... 128.70 164.40 192.50 225.20 11343
11344 Ditto with underlays.................................................................................................................................................................. 154.30 189.10 217.10 251.80 11344
Supply and lay carpet including backing as "Environmentally Friendly Carpet" in any series and Carpet
colour finish required : - Pile weight (kg/m)
n.e. 1.00 exc. 1.00
to floor to stairs to floor to stairs
A B C D
Per square metre $ $ $ $
11345 Carpet laid with grippers........................................................................................................................................................... 185.10 220.50 228.30 272.50 11345
11346 Ditto with underlays.................................................................................................................................................................. 210.30 245.60 257.00 288.80 11346
11/39
11 PLASTERING AND FINISHES 11
Item Item
HEAVY CONTRACT QUALITY CARPET (CONT'D)
CARPET; GRIPPER METHOD (CONT'D)
Carpet
Alterations and repairs : - to floor to stairs
A B
Per square metre $ $
11347 Take up and clear away existing carpet of any type with or without underlay............................................................................................................ 5.70 6.90 11347
11348 Take up existing carpet of any type and set aside for re-use........................................................................................................................................ 14.00 16.80 11348
11349 Ditto but including underlays....................................................................................................................................................................................... 16.80 20.20 11349
11350 Lay only carpet of any type with and including grippers............................................................................................................................................. 19.50 53.60 11350
11351 Ditto with underlays ditto............................................................................................................................................................................................. 24.40 58.50 11351
11352 Lay only carpet of any type including provision of new underlays and clear away old underlays ditto..................................................................... 49.10 83.20 11352
100% PURE WOOL CARPET; GRIPPER METHOD
Carpet
Pile weight (kg/m)
n.e. 2.05 exc. 2.05
to floor to stairs to floor to stairs
A B C D
Per square metre $ $ $ $
11353 Carpet 'machine tufted' laid with grippers................................................................................................................................ 327.10 357.50 368.30 407.90 11353
11354 Ditto with underlays.................................................................................................................................................................. 344.20 375.10 403.70 436.60 11354
11355 Carpet 'hand made' laid with grippers....................................................................................................................................... 555.10 587.30 599.70 631.90 11355
11356 Ditto with underlays.................................................................................................................................................................. 583.70 619.50 628.30 664.10 11356
Alterations and repairs : - Carpet
to floor to stairs
A B
Per square metre $ $
11357 Take up and clear away existing carpet of any type..................................................................................................................................................... 5.10 6.90 11357
11358 Take up existing carpet of any type and set aside for re-use........................................................................................................................................ 13.40 16.10 11358
11359 Ditto but including underlays....................................................................................................................................................................................... 16.10 19.30 11359
11360 Lay only carpet of any type with and including grippers............................................................................................................................................. 19.50 59.00 11360
11361 Ditto with underlays ditto............................................................................................................................................................................................. 24.40 63.80 11361
11362 Lay only carpet of any type including provision of new underlays and clear away old underlays ditto..................................................................... 54.00 88.60 11362
11/40
11 PLASTERING AND FINISHES 11
Item Item
HEAVY CONTRACT QUALITY CARPET TILES
CARPET TILE; FULLY ADHERING METHOD
Carpet tiles
Supply and lay carpet tiles module size n.e. 0.40 m in all types of backing Pile weight (kg/m)
and in all series and colour finish required : - n.e. 1.00 exc. 1.00
to floor to stairs to wall to floor to stairs to wall
A B C D E F
Per square metre $ $ $ $ $ $
11363 Carpet tiles laid with adhesive.............................................................................................................. 135.10 155.90 169.80 162.30 178.40 206.20 11363
11364 Ditto laid with adhesive and release bond agent.................................................................................. 141.90 164.40 196.80 173.40 189.50 217.30 11364
Supply and lay carpet tiles module size n.e. 1.00 m including backing as
"Environmentally Friendly Carpet" in any series and colour finish required : -
Per square metre
11365 Carpet tiles laid with adhesive.............................................................................................................. 165.90 182.10 211.60 195.30 211.40 222.80 11365
11366 Ditto laid with adhesive and release bond agent.................................................................................. 177.10 193.20 222.80 206.40 222.50 250.30 11366
Supply and lay carpet tiles module size n.e. 0.40 m including backing as "Environmentally Friendly Carpet" Carpet tile
in any series and colour finish required : - Pile density (fibre/m)
exc. 75 million
to floor to stairs to wall
A B C
Per square metre $ $ $
11367 Carpet tiles laid with adhesive.................................................................................................................................................................... 271.40 291.50 313.50 11367
11368 Ditto laid with adhesive and release bond agent........................................................................................................................................ 282.20 302.70 328.20 11368
Carpet
Alterations and repairs : - to floor to stairs to wall
A B C
Per square metre $ $ $
11369 Take up and clear away existing carpet tiles of any type........................................................................................................................... 5.70 6.90 6.30 11369
11370 Take up existing carpet tiles of any type and set aside for re-use.............................................................................................................. 14.00 16.80 15.40 11370
11371 Lay only carpet tiles of any type with adhesive.......................................................................................................................................... 23.60 26.80 24.20 11371
11372 Lay only carpet tiles of any type with adhesive and release bond agent.................................................................................................... 25.50 30.60 28.10 11372
11/41
11 PLASTERING AND FINISHES 11
Item Item
ENTRANCE MATTING
Take Take
Supply and install entrance matting comprises aluminium rolling mat strips and Supply down down Fix
frames and aluminium/rubber/carpet scraper strip in any colour, profile spacing and and and set only
and finish : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
11373 Heavy duty entrance matting, ribbed carpet/grooved rubber/brush/aluminium scraper
finished strip, n.e. 17 mm high................................................................................................................................................. 3,032.00 35.70 54.20 97.40 11373
11374 Ditto, 17 - 22 mm high.............................................................................................................................................................. 3,225.60 35.70 54.20 97.40 11374
11375 Ditto, 22- 27 mm high............................................................................................................................................................... 3,744.80 35.70 54.20 97.40 11375
TAKING DOWN EXISTING PLASTER, PAVINGS, TILING, SUSPENDED CEILING, ETC.
(Note : - The items under column A hereafter shall not be measured if the wall or slab, etc. to which the finish being affixed is to
be taken down.)
Take Take
Take down and clear away, or set aside for re-use as required, the following from any position : - down down
and and set
clear aside for
away re-use
A B
Per square metre $ $
11376 Expanded metal lathing ................................................................................................................................................................................................ 3.20 - 11376
11377 Lightweight screeds to floors and roofs of any thickness ............................................................................................................................................ 11.50 - 11377
11378 Cement and sand paving, floor screeds or floor rendering of any mix or thickness, including covering to stair treads,
risers, kerbs, channels and the like .............................................................................................................................................................................. 9.60 - 11378
11379 Cement and sand wall or ceiling rendering, screeds, skirting and the like ................................................................................................................. 12.10 - 11379
11380 Internal plaster, external plaster, acoustic plaster, Shanghai plaster or gypsum plaster of any mix, thickness,
or number of coats......................................................................................................................................................................................................... 11.50 - 11380
11381 Flexible sheets and skirting of any type to floor or wall (screed measured separately)............................................................................................... 8.30 10.90 11381
11382 "Sandtex-trowel" finish including backing screed if any ............................................................................................................................................ 17.20 - 11382
11383 Granolithic or terrazzo paving of any mix or thickness, including covering to stair treads, risers, kerbs, channels and
the like, and backing screed if any ............................................................................................................................................................................... 16.60 - 11383
11384 Granolithic or terrazzo wall dadoes and skirting of any mix or thickness including backing screed if any............................................................... 13.40 - 11384
11385 Ceramic or quarry floor tiling, skirting, etc., of any type (screed measured separately) ............................................................................................ 11.50 - 11385
11386 Precast concrete floor tiling or skirting of any thickness (ditto) ................................................................................................................................. 10.90 14.70 11386
11387 Terrazzo floor tiling, skirting, etc. of any type (ditto).................................................................................................................................................. 12.80 17.90 11387
11388 Cork tiling of any thickness to floor, wall or ceiling (ditto) ........................................................................................................................................ 4.50 5.70 11388
11389 Flexible tiles and skirting of any type to floor or wall (ditto)....................................................................................................................................... 8.30 10.90 11389
11/42
11 PLASTERING AND FINISHES 11
Item Item
TAKING DOWN EXISTING PLASTER, PAVINGS, TILING, SUSPENDED CEILING, ETC.
(CONT'D)
Take Take
(Note : - The items under column A hereafter shall not be measured if the wall or slab, etc. to which the finish being down down
affixed is to be taken down.) (Cont'd) and and set
clear aside for
Take down and clear away, or set aside for re-use as required, the following from any position : - (Cont'd) away re-use
A B
Per square metre $ $
11390 Rubber tiles and sheets to floors, and treads and risers of any type (ditto) ................................................................................................................ 8.30 10.90 11390
11391 Mosaic floor or wall tiling of any type (ditto) .............................................................................................................................................................. 11.50 - 11391
11392 Glazed or ceramic wall tiling of any type (ditto) ......................................................................................................................................................... 11.50 - 11392
11393 Precast concrete paving slabs of any thickness (screed measured separately) ........................................................................................................... 10.90 14.70 11393
11394 Rectangular or interlocking precast concrete paving blocks of any thickness (ditto) ................................................................................................ 12.80 17.20 11394
11395 Artificial granite floor or wall tiling of any thickness (ditto)....................................................................................................................................... 13.40 18.50 11395
11396 Clay brick paver of any size (ditto)............................................................................................................................................................................... 12.10 16.00 11396
11397 Natural marble or granite slabs in any thickness on floors, walls, columns, vertical surfaces in dadoes and wall lining,
treads and risers, end of stairs, top and sides of counters, window cills and the like (screed measured separately).................................................. 13.40 18.50 11397
11398 Resin stone slabs in any thickness (screed measured separately) ............................................................................................................................... 12.10 17.20 11398
11399 Marble/granite tiles of any size (ditto).......................................................................................................................................................................... 11.50 15.30 11399
11400 Pebble or small stone paving of any mix or thickness................................................................................................................................................. 8.30 - 11400
Per linear metre
11401 Plaster of paris mouldings and moulded cornices n.e. 150 mm girth, complete with bracketing and the like........................................................... 3.20 - 11401
11402 Ditto 150 - 300 mm girth, ditto .................................................................................................................................................................................... 3.80 - 11402
11403 Brick curb of any size.................................................................................................................................................................................................... 5.10 7.00 11403
11404 Natural marble or granite moulding n.e. 100 mm wide............................................................................................................................................... 5.10 7.00 11404
11405 Ditto 100 - 200 mm wide.............................................................................................................................................................................................. 5.70 8.90 11405
11/43
11 PLASTERING AND FINISHES 11
Item Item
SUPPLY ONLY OF MATERIALS
A
Per square metre $
11406 6 mm Thick cork tiles .................................................................................................................................................................................................................... 64.00 11406
11407 9 mm Ditto ....................................................................................................................................................................................................................................................
87.30 11407
11408 12 mm Ditto ....................................................................................................................................................................................................................................................
107.40 11408
Thickness (mm)
n.e. exceed-
9.5 ing 9.5
A B
Per square metre $ $
11409 Ceramic and quarry floor tiles each tile size n.e. 0.36m............................................................................................................................................. 91.40 105.50 11409
11410 Ceramic and quarry floor tiles each tile size exceeding 0.36m................................................................................................................................... 84.50 98.20 11410
11411 Ditto but to treads and risers of stairs, sides and top of upstand kerbs, sides and
bottom of channels and the like each tile size n.e. 0.36m........................................................................................................................................... 97.80 111.90 11411
11412 Ditto but to treads and risers of stairs, sides and top of upstand kerbs, sides and
bottom of channels and the like each tile size exceeding 0.36m................................................................................................................................ 91.00 104.70 11412
Per linear metre
11413 Ceramic and quarry skirting tiles 100 mm high .......................................................................................................................................................... 34.20 39.90 11413
11414 Ceramic and quarry skirting tiles 150 mm high........................................................................................................................................................... 45.70 52.20 11414
11415 Ceramic and quarry skirting tiles 200 mm high........................................................................................................................................................... 76.00 83.30 11415
Add to either of Items 11409 to 11415 inclusive for ceramic and quarry floor tiles of specific quality...................................................................................... 65%
A
Per square metre $
11416 Re-constituted artificial granite strip tile n.e. 0.01 m, 10 - 15 mm thick...................................................................................................................................... 118.20 11416
11417 Re-constituted artificial granite strip tile exceeding 0.01 m, 10 - 15 mm thick........................................................................................................................... 105.50 11417
11418 Re-constituted artificial granite square/rectangular tile n.e. 0.01 m, 12 - 18 mm thick............................................................................................................... 114.60 11418
11419 Re-constituted artificial granite square/rectangular tile exceeding 0.01 m, 12 - 18 mm thick.................................................................................................... 105.50 11419
Add to either of Items 11416 to 11419 inclusive for re-constituted artificial grantie tiles of specific quality............................................................................. 65%
11/44
11 PLASTERING AND FINISHES 11
Item Item
SUPPLY ONLY OF MATERIALS (CONT'D)
A
Per square metre $
11420 Terrazzo floor tiles to BS EN 13748 in any colour and surface finish, 20 mm thick.................................................................................................................... 92.70 11420
11421 Semi-flexible p.v.c. tiles in any colour and surface finish, 2.5 mm thick...................................................................................................................................... 50.70 11421
11422 Vinyl tiles in any colour and surface finish 2 mm thick................................................................................................................................................................. 68.90 11422
11423 Linoleum tiles in any colour and surface finish 3.2 mm thick....................................................................................................................................................... 147.70 11423
11424 Unbacked flexible sheet in any colour and surface finish, 1.2 mm thick...................................................................................................................................... 104.60 11424
11425 Unbacked flexible sheet in any colour and surface finish, 2 mm thick......................................................................................................................................... 117.40 11425
11426 Foam backed (1.5 mm thick) flexible sheet in any colour and surface finish, overall 3 mm thick............................................................................................... 118.40 11426
11427 Linoleum flexible sheet in any colour and surface finish, 3.2 mm thick....................................................................................................................................... 217.60 11427
11428 Linoleum flexible sheet in any colour and surface finish, 4.5 mm thick....................................................................................................................................... 292.40 11428
11429 Antistatic homogeneous vinyl tiles, 2 mm thick............................................................................................................................................................................ 194.40 11429
11430 Antistatic homogeneous vinyl sheet, 2 mm thick........................................................................................................................................................................... 215.20 11430
11431 Rubber tiles in any colour and surface finish, 4 mm thick............................................................................................................................................................. 307.80 11431
11432 Rubber sheet in any colour and surface finish, 4 mm thick........................................................................................................................................................... 344.40 11432
Per linear metre
11433 Preformed flexible PVC skirting 100 mm high coved bottom...................................................................................................................................................... 28.90 11433
11434 'L' shape PVC skirting, 100 x 45 x 2 mm thick............................................................................................................................................................................. 32.40 11434
11/45
11 PLASTERING AND FINISHES 11
Item Item
SUPPLY ONLY OF MATERIALS (CONT'D)
A
Per square metre $
11435 Glazed ceramic mosaic tiles in any colour and size....................................................................................................................................................................... 79.20 11435
11436 Unglazed vitreous mosaic tiles in any colour and size................................................................................................................................................................... 95.30 11436
11437 Ceramic wall tiles each tile size n.e. 0.05 m and n.e. 9.5 mm thick............................................................................................................................................. 87.30 11437
11438 Ceramic wall tiles each tile size exceeding 0.05 m and n.e. 9.5 mm thick.................................................................................................................................. 97.50 11438
11439 Ceramic wall tiles each tile size n.e. 0.05 m and exceeding 9.5 mm thick ................................................................................................................................. 104.30 11439
11440 Ceramic wall tiles each tile size exceeding 0.05 m and exceeding 9.5 mm thick ....................................................................................................................... 104.30 11440
Add to either of Items 11437 to 11440 inclusive for ceramic wall tiles of specific quality.......................................................................................................... 65%
A
Per square metre $
11441 Glazed ceramic swimming pool tiles in any colour size, surface finish and thickness................................................................................................................. 280.20 11441
11442 Fully adhered or loosely laid carpet, pile weight n.e. 1.50 kg/m delivered to Site....................................................................................................................... 89.50 11442
11443 Fully adhered or loosely laid carpet, pile weight exceeding 1.50 kg/m delivered to Site............................................................................................................ 104.10 11443
11444 Fully adhered or loosely laid "Environmental Friendly" carpet, pile weight n.e. 1.00 kg/m delivered to Site............................................................................ 139.30 11444
11445 Fully adhered or loosely laid "Environmental Friendly" carpet, pile weight exc. 1.00 kg/m delivered to Site........................................................................... 192.00 11445
11446 Carpet tile module size n.e. 0.40 m, pile weight n.e. 1.00 kg/m delivered to Site...................................................................................................................... 118.70 11446
11447 Carpet tile module size n.e. 0.40 m, pile weight exc. 1.00 kg/m delivered to Site..................................................................................................................... 141.20 11447
11448 "Environmental Friendly" Carpet tiles size n.e. 1.00 m, pile weight n.e. 1.00 kg/m delivered to Site....................................................................................... 144.80 11448
11449 "Environmental Friendly" Carpet tiles size n.e. 1.00 m, pile weight exc. 1.00 kg/m delivered to Site...................................................................................... 179.10 11449
11450 "Environmental Friendly" Carpet tiles, pile density (fibre/m) exceeding 75 million in any series, delivered to Site................................................................. 260.90 11450
11451 100% pure wool, pile weight n.e. 2.05 kg/m "machine tufted" carpet delivered to Site.............................................................................................................. 288.40 11451
11452 100% pure wool, pile weight exceeding 2.05 kg/m "machine tufted" carpet delivered to Site................................................................................................... 365.20 11452
11453 100% pure wool, pile weight n.e. 2.05 kg/m "hand made" carpet delivered to Site.................................................................................................................... 560.90 11453
11454 100% pure wool, pile weight exceeding 2.05 kg/m "hand made" carpet delivered to Site.......................................................................................................... 599.30 11454
11455 Carpet underlay delivered to Site.................................................................................................................................................................................................... 31.10 11455
11/46
Section 12
ROADWORK AND CABLE DUCT
12 ROADWORK AND CABLE DUCT 12
SECTION 12
ROADWORK AND CABLE DUCT
SPECIAL CONDITIONS
Drawings SC12.01 The drawings referred to in this Section and listed in Annex 'A' - Drawing Schedule and
Drawings for Builder's Works of the Schedule can be viewed on the ArchSD internet
website via the pathway referred therein.
Specification SC12.02 This Section shall be read and used in conjunction with the G.S. Section 24 - External
Works.
Measurement SC12.03 All excavation, concrete work, steel and metal work, plaster work and drainage work will
of excavation, be measured separately and paid for at appropriate rates under applicable Work Sections
concrete work, of this Schedule unless specifically described in this Section.
etc.
Measurement SC12.04 The measurement of granular beds, base or sub-base shall be the compacted thickness as
of granular specified by the Maintenance Surveyor, whether laid in one or more layers. No deductions
beds, base or shall be made for manholes, gullies, catch pits, inspection covers, columns or piers, etc.
sub-base not exceeding 1.00 m.
In the case of quadrants, the outer circular girth shall be measured.
ROADWORK
Rates SC12.05 Rates for all items shall include for any or all of the following as applicable : -
generally
(a) Finishing surfaces level or to falls, gradients, crowns and cambers to exact profile
required, with each successive surface finished parallel to the final finished surface.
(b) Additional bulk of material required to allow for compaction and consolidation.
(c) All wheeling and multi-handing of material to place of final incorporation in the
work.
(d) Maintenance and cleaning of surfaces.
(e) Protection of curbs, masking and unmasking of drainage channels, manhole
covers, gully gratings, expansion joints, road studs and road marking.
(f) Provision, maintenance and removal of measures to maintain traffic flow including
all temporary traffic diversion lighting and signs including labours and all charges
incurred.
(g) Provision, maintenance and removal of temporary road, walkway covers to
trenches and the like.
12/1
12 ROADWORK AND CABLE DUCT 12
SPECIAL CONDITIONS
ROADWORK
Rates SC12.05 (h) Obtaining permits from Government departments before execution of the works.
generally (Cont'd)
(Cont'd) (i) Mobilization, maintenance and demobilization of paving machine, rollers,
compaction plant, milling machine and the like.
(j) Coring, testing and reinstatement with bituminous material shall include for : -
(i) Marking the edges of the surfaces to be cored.
(ii) Making good any overbreak, cracking or other damages.
(iii) Cleaning up and removing surplus material and waste.
(iv) Taking core samples, sealing and transferring in the proper sequence to
core box and delivering them to place of testing.
(v) Recording and submitting records and reports.
(vi) Filling up core holes with appropriate materials.
Rates for SC12.06 Rates for granular sub-base and/or lean concrete sub-base shall further include for : -
granular
sub-base (a) Trial areas.
and/or lean
concrete (b) Reclaimed asphalt pavement as specified in the G.S. Item 24.06.
(c) Grading, measuring, mixing, transporting, depositing, spreading, levelling and
compacting.
(d) Making of all joints.
(e) In the case of lean concrete sub-base, all testing and formwork.
(f) Spillage and slopes at edges.
(g) Edge support.
Rates for SC12.07 Rate for bituminous road base shall further include for : -
bituminous
road base (a) Trial areas.
(b) Reclaimed asphalt pavement as specified in the G.S. Item 24.06.
(c) Grading, measuring, mixing, transporting, depositing, spreading, levelling and
compacting.
(d) Making of all joints.
(e) Spillage and slopes at edges.
12/2
12 ROADWORK AND CABLE DUCT 12
SPECIAL CONDITIONS
ROADWORK
Rates for SC12.07 (f) Edge support.
bituminous (Cont'd)
road base (g) Sealing surfaces, priming and tack coats.
(Cont'd)
Rates for SC12.08 The rates for bituminous flexible surfacing shall further include for : -
bituminous
flexible (a) Preparation and cleaning of surface to receive bituminous materials.
surfacing
(b) Reclaimed asphalt pavement as specified in the G.S. Item 24.06.
(c) Grading, measuring, mixing, transporting, depositing, spreading, levelling and
compacting.
(d) Cutting back and making of joints including applying bituminous priming coats.
(e) Maintenance of surface and cleaning or removal and replacement of contaminated
layers.
(f) Spillage and slopes at edges.
(g) Making good up to curbs and around manholes and gully covers and frames and
up to existing services and around expansion joints.
(h) Making good up to existing flexible surfacing.
(i) Sealing surfaces, priming and tack coats.
Rates for SC12.09 The rates for stone mastic asphalt surface shall further include for : -
stone mastic
asphalt (a) Preparation and cleaning of surface to receive stone mastic asphalt materials.
surface
(b) Grading, measuring, mixing, transporting, depositing, spreading, levelling and
compacting.
(c) Cutting back and making of joints including applying bituminous priming coats.
(d) Maintenance of surface and cleaning or removal and replacement of contaminated
layers.
(e) Spillage and slopes at edges.
(f) Making good up to curbs and around manholes and gully covers and frames and
up to existing services and around expansion joints.
(g) Making good up to existing flexible surfacing.
(h) Sealing surfaces, priming and tack coats.
12/3
12 ROADWORK AND CABLE DUCT 12
SPECIAL CONDITIONS
ROADWORK
Rates for SC12.10 The rates for cold milling of wearing course shall further include for : -
cold milling
of wearing (a) Removal of all material arising.
course
(b) Preparation and brushing of surface.
(c) Multiple milling to the depth, profile shape, fall and the texture surface required.
(d) Making good up to curbs and around manholes and gully covers and frames and
up to existing services and around expansion joints.
(e) Making good up to existing flexible surfacing.
(f) Loosing, breaking of milled particles.
(g) Cleaning milled surface by mechanical vacuum road sweeper.
Rates for SC12.11 The rates for patching up potholes with bituminous material shall further include for : -
patching up
potholes with (a) Potholes of any thickness.
bituminous
material (b) Removal of debris and loose material from potholes.
(c) Drying out water in potholes.
(d) Preparation of surface and applying bituminous priming coat.
(e) Placing and compacting bituminous material marrying in with existing surfaces.
Rates for SC12.12 The rates for patching up potholes with instant filling material shall further include for : -
patching up
potholes with (a) Potholes of any thickness.
instant filling
material (b) Removal of debris and loose material from potholes.
(c) Drying out water in potholes.
(d) Placing and compacting instant hole filling material marrying in with existing
surfaces.
Rates for SC12.13 The rates of concrete carriageway shall further include for : -
concrete
carriageway (a) Trial mixes.
(b) Waterproofing membrane underlays.
(c) Formwork and trimming bars.
12/4
12 ROADWORK AND CABLE DUCT 12
SPECIAL CONDITIONS
ROADWORK
Rates for SC12.13 (d) Spreading, compacting and finishing the concrete.
concrete (Cont'd)
carriageway (e) In the case of rapid hardening concrete, providing and mixing approved concrete
(Cont'd) admixture for early strength or rapid hardening cement.
(f) Surface texturing, curing and protection.
(g) Forming channels as an integral part of the slab.
(h) Forming recesses, openings and bays for manholes, gullies and road studs.
(i) Forming surfaces within vertical and horizontal tolerances and surface regularity.
(j) Restrictions on the use of pavement courses by construction traffic.
(k) Making good up to existing.
(l) Forming expansion, longitudinal and contraction joints including all necessary
formwork.
Rates for SC12.14 The rates for steel fabric reinforcement shall include for : -
steel fabric
reinforcement (a) Extra fabric reinforcement at laps.
(b) All requirements of sampling and testing.
(c) Cleaning, cutting to size, bending, fixing and securely supporting in the required position.
(d) Plastic cover spacers, spacer blocks, steel spacer rods, steel chairs and annealed
iron tying wire or tack welding.
Rates for SC12.15 The rates for longitudinal, expansion and contraction joints shall include for : -
longitudinal,
expansion and (a) Forming joints through full thickness of concrete slab carriageway and surfacing
contraction including formwork.
joints
(b) Removal of dust and debris.
(c) Provision of bond breaker or backing strips.
(d) Masking tape to sides of groove.
(e) Application of primer to sides of sealing grooves.
(f) Joint assemblies complete including, as appropriate, groove forming strip, tie bars
with PVC sleeves, crack inducers, dowel bars, dowel sheaths, dowel bar cradles,
joint filler and joint sealant.
(g) Removal of groove forming strip at movement joints after concrete has set.
12/5
12 ROADWORK AND CABLE DUCT 12
SPECIAL CONDITIONS
ROADWORK
Rates for SC12.16 The rates for run-in shall further include for : -
run-in
(a) Cutting pavement by saw cut, excavating and clearing away or filling and
compacting excavated materials.
(b) Taking up and clearing away from Site or setting aside for re-lay existing curbs.
(c) Breaking up and clearing away from Site existing concrete bedding for curbs.
(d) Preparation of formation and compacting base.
(e) Laying and compacting of 150 mm granular sub-base.
(f) Concrete pavement up to 200 mm thick and finishing surface.
(g) Supplying and laying steel fabric reinforcement.
(h) Supplying and laying additional/replacement drop curbs including concrete
bedding as required.
Rates for SC12.17 The rates for granite or precast concrete curbs, precast concrete footway edgings, etc.
curbs, precast shall include for : -
concrete
footway (a) Excavating in any materials, ramming bottom, back filling and removal surplus
edgings, etc. materials from Site.
(b) Concrete bedding, backing and foundation for curbs or edgings.
(c) Formwork.
(d) Reinforcement.
(e) Keying of surface and tack coat.
(f) Finishing, protecting and curing.
(g) Making and sealing joints.
(h) Dressing of curbs as required.
Rates for SC12.18 The rates for concrete footways shall include for : -
concrete
footways (a) Trial mixes.
(b) Waterproofing membrane underlays.
(c) Formwork and trimming bars.
(d) Spreading, compacting and finishing the concrete.
12/6
12 ROADWORK AND CABLE DUCT 12
SPECIAL CONDITIONS
ROADWORK
Rates for SC12.18 (e) In the case of rapid hardening concrete, providing and mixing approved concrete
concrete (Cont'd) admixture for early strength or rapid hardening cement.
footways
(Cont'd) (f) Surface texturing, curing and protection.
(g) Spillage and slopes at sides.
(h) Forming channels as an integral part of the slab.
(i) Forming recesses, openings and bays for manholes, gullies and road studs.
(j) Forming surfaces within vertical and horizontal tolerances and surface regularity.
(k) Forming and including expansion, longitudinal and contraction joints including all
necessary formwork.
(l) Restrictions on the use of pavement courses by construction traffic.
(m) Making good up to existing.
CABLE DUCT
Measurement of SC12.19 All cable duct pipes shall be measured net as laid or fixed over all fittings.
cable duct pipes
Rates for SC12.20 The rates for concrete beds, haunchings and surrounds to pipes shall include for : -
concrete beds,
haunchings (a) Providing and laying a layer of polythene sheeting or concrete blinding on the
and surrounds bottom of trenches before concreting.
to pipes
(b) All necessary formwork and falsework.
(c) Forming flexible joints including joint filler.
(d) All necessary precast concrete wedges, blocks or cradles or other approved pipe
supports including compressible sheeting.
(e) Keeping concrete and pipes damp until backfilling placed.
Rates for SC12.21 The rates for granular beds shall include for : -
granular beds
(a) Recycled or non-recycled granular bedding material to be clean, hard, durable,
crushed rock or crushed concrete, broken stone, hard brick, concrete or other
comparable hard insert approved by the Maintenance Surveyor.
(b) Compacting and trimming granular beds to correct gradient and shape under
barrel and pipe sockets.
(c) Handling from temporary spoil heaps.
12/7
12 ROADWORK AND CABLE DUCT 12
SPECIAL CONDITIONS
CABLE DUCT
Rates for SC12.21 (d) Additional bulk of material required to allow for compaction and consolidation.
granular beds (Cont'd)
(Cont'd) (e) Re-compacting and laying granular around pipes after testing.
Rates for cable SC12.22 The rates for cable duct pipes shall include for : -
duct pipes
(a) All short lengths and all cutting and waste.
(b) All jointing and jointing materials as required.
(c) Provision of nylon draw cord in each length of duct.
(d) Provision of all information required by the Maintenance Surveyor for preparation
of record drawings.
12/8
12 ROADWORK AND CABLE DUCT 12
Item Item
ROAD, CARPARKS AND PAVED AREAS
SUB-BASE
A
Per cubic metre $
12001 Granular sub-base............................................................................................................................................................................................................................ 142.90 12001
12002 Lean concrete sub-base................................................................................................................................................................................................................... 559.80 12002
ROAD BASE
A
Per cubic metre $
12003 Bituminous road base...................................................................................................................................................................................................................... 614.60 12003
FLEXIBLE SURFACING
Nominal aggregate size (mm)
Supply, lay and roll with roller for the following bituminous surfacing (consolidated thickness stated) : - 37.5 28 20 10
A B C D
Per square metre $ $ $ $
12004 55 mm Thick bituminous base course...................................................................................................................................... 64.80 - - - 12004
12005 Extra over Item 12004 for each 5 mm thickness or part thereof in excess of 55 mm.............................................................. 6.00 - - - 12005
12006 55 mm Thick bituminous base course...................................................................................................................................... - 69.60 - - 12006
12007 Extra over Item 12006 for each 5 mm thickness or part thereof in excess of 55 mm.............................................................. - 6.60 - - 12007
12008 40 mm Thick bituminous wearing course................................................................................................................................ - - 68.60 - 12008
12009 Extra over Item 12008 for each 5 mm thickness or part thereof in excess of 40 mm.............................................................. - - 7.10 - 12009
12010 30 mm Thick bituminous wearing course................................................................................................................................ - - - 47.40 12010
12011 Extra over Item 12010 for each 5 mm thickness or part thereof in excess of 30 mm.............................................................. - - - 8.00 12011
Thickness (mm)
10 20 40
A B C
Per square metre $ $ $
12012 Stone mastic asphalt surfaces...................................................................................................................................................................... 18.10 34.60 62.90 12012
A
$
12013 Extra over Item 12012 for each 5 mm thickness or part thereof in excess of 40 mm................................................................................................................... 6.80 12013
12/9
12 ROADWORK AND CABLE DUCT 12
Item Item
ROAD, CARPARKS AND PAVED AREAS (CONT'D)
COLD MILLING WORK
A
Per square metre $
12014 Cold mill 25 mm thick wearing course with shaving machine and remove from Site all materials arising................................................................................. 15.00 12014
12015 Extra over Item 12014 for each 25 mm thickness or part thereof in excess of 25 mm................................................................................................................. 12.10 12015
PATCHING UP POTHOLES
(Note : - Items 12016 to 12017 inclusive shall only be measured when individual potholes n.e. 2.0 m Pothole size (m)
each are repaired.) n.e. 0.2 0.2 - 0.5 0.5 - 1.0 1.0 - 2.0
A B C D
Each $ $ $ $
12016 Patch up pothole with bituminous material.............................................................................................................................. 21.70 31.70 49.00 97.90 12016
12017 Patch up pothole with instant hole filling material................................................................................................................... 83.70 218.70 438.60 877.10 12017
REINFORCED CONCRETE CARRIAGEWAY
A
Per cubic metre $
12018 Reinforced concrete Grade 40S, Grade 40D or 40MPa carriageway............................................................................................................................................ 707.40 12018
12019 Extra over Item 12018 for rapid hardened concrete....................................................................................................................................................................... 210.40 12019
BS 4483 or SS-32 Reference number
STEEL FABRIC REINFORCEMENT C785 C636 C503 C385 C283
A B C D E
Per square metre $ $ $ $ $
12020 Supply and lay steel fabric reinforcement............................................................................................................... 39.90 36.00 30.20 25.40 21.30 12020
RUN-IN
A
Each $
12021 Concrete run-in size n.e. 10 m....................................................................................................................................................................................................... 2,288.10 12021
A
Per square metre $
12022 Concrete run-in size exceeding 10 m............................................................................................................................................................................................ 218.70 12022
12/10
12 ROADWORK AND CABLE DUCT 12
Item Item
ROAD, CARPARKS AND PAVED AREAS (CONT'D)
REPAIRS TO EXISTING CONCRETE SURFACING
Depth of grooves (mm) n.e. 15 15 - 25 n.e. 20 20 - 25 n.e. 20 20 - 35 n.e. 40
Width of grooves (mm) n.e. 10 n.e. 10 10 - 15 10 - 15 15 - 20 15 - 20 20 - 25
A B C D E F G
Per linear metre $ $ $ $ $ $ $
12023 Saw cut groove in concrete carriageway for joint sealant.................................................. 18.50 26.90 29.10 36.40 43.70 88.70 115.50 12023
Bar diameter (mm) 12 20 25
Embedded length (mm) 200 325 325
A B C
Each $ $ $
12024 Drill hole in edge of concrete carriageway for dowel bar and PVC sleeve............................................................................................... 21.90 39.10 48.60 12024
LONGITUDINAL, EXPANSION AND CONTRACTION JOINTS TO EXISTING Thickness of
CONCRETE SURFACING slab (mm)
n.e. 150 150-310
A B
Per linear metre $ $
12025 Form expansion joint through full thickness of slab.................................................................................................................................................... 202.60 290.60 12025
12026 Form longitudinal joint ditto......................................................................................................................................................................................... 110.30 120.70 12026
12027 Form contraction joint ditto.......................................................................................................................................................................................... 209.60 277.30 12027
FOOTWAYS, CYCLE TRACKS, PAVING AND CURBING
A
Per linear metre $
12028 Granite curb n.e. 200 mm high including backing and foundations.............................................................................................................................................. 128.40 12028
12029 Extra over Item 12028 for each additional 50 mm high or part thereof in excess 200 mm high.................................................................................................. 7.70 12029
12030 Extra over either of Items 12028 to 12029 inclusive for curb n.e. 15.00 m radius....................................................................................................................... 42.50 12030
12031 Granite quadrant n.e. 200 mm high including backing and foundations....................................................................................................................................... 209.30 12031
12032 Extra over Item 12031 for each additional 50 mm high or part thereof in excess 200 mm.......................................................................................................... 47.70 12032
12033 Extra over either of Items 12031 to 12032 inclusive for quadrant n.e. 15.00 m radius................................................................................................................ 42.50 12033
12034 Lay only granite curbs/quadrants of any size including backing and foundations........................................................................................................................ 109.50 12034
12035 Ditto but n.e. 15.00 m radius.......................................................................................................................................................................................................... 122.10 12035
12/11
12 ROADWORK AND CABLE DUCT 12
Item Item
FOOTWAYS, CYCLE TRACKS, PAVING AND CURBING (CONT'D) Concrete curb type
K1 K2 K3 K5 or K9 K6 or K8 K7
A B C D E F
Per linear metre $ $ $ $ $ $
12036 Precast concrete curb including backing and foundations................................................................... 121.70 131.60 126.20 142.60 139.70 122.80 12036
12037 Extra over Item 12036 for curb n.e. 15.00 m radius............................................................................. 43.20 43.20 39.80 45.10 45.10 36.30 12037
12038 Lay only precast concrete curb including backing and foundations.................................................... 102.80 102.80 95.20 104.90 104.90 91.80 12038
12039 Ditto but n.e. 15.00 m radius................................................................................................................. 120.00 120.00 111.10 122.40 122.40 107.20 12039
Edging type
E1 E2 E3
A B C
Per linear metre $ $ $
12040 Precast concrete footpath edging including backing and foundations....................................................................................................... 121.80 123.40 120.40 12040
A
Per linear metre $
12041 Precast concrete quadrant to suit curbs and edgings of any size and radius including backing and foundations........................................................................ 162.00 12041
A
Per cubic metre $
12042 Plain concrete Grade 30S, Grade 30D or 30MPa footway............................................................................................................................................................. 585.80 12042
12043 Plain concrete Grade 30S, Grade 30D or 30MPa margin or edging.............................................................................................................................................. 966.30 12043
12044 Ditto flat or dish channel................................................................................................................................................................................................................. 976.40 12044
12045 Extra over either of Items 12042 to 12044 inclusive for concrete footpath with rapid hardening concrete................................................................................. 269.00 12045
12046 Reinforced concrete Grade 30S, Grade 30D or 30MPa footway................................................................................................................................................... 652.80 12046
12047 Ditto margin or edging.................................................................................................................................................................................................................... 1,081.50 12047
12/12
12 ROADWORK AND CABLE DUCT 12
Item Item
FOOTWAYS, CYCLE TRACKS, PAVING AND CURBING (CONT'D)
SUNDRIES
A
Per square metre $
12048 Take up and clear away from Site existing paving slabs/blocks and sand bedding...................................................................................................................... 36.20 12048
12049 Take up, set aside for re-use and re-lay existing paving slabs/blocks and sand bedding including
additional sand filling and bedding................................................................................................................................................................................................ 66.50 12049
Per linear metre
12050 Take up and clear away from Site existing granite curbs or precast concrete curb, in any size and any
radius, and associated concrete bedding, backing and foundation................................................................................................................................................ 35.80 12050
12051 Take up, set aside for re-use and re-lay existing granite curbs or precast concrete curbs, ditto................................................................................................... 170.10 12051
CABLE DUCT
CABLE DUCT PIPES Type and bore of pipe (mm)
U.P.V.C. Galvanized mild steel
50 75 100 150 50 80 100 150
A B C D E F G H
Per linear metre $ $ $ $ $ $ $ $
12052 Pipe laid in trench as cable duct........................................................................ 24.80 43.80 64.20 123.80 58.00 78.00 109.90 163.20 12052
12053 Take up and clear away ditto............................................................................. 2.60 3.80 4.50 6.40 4.50 6.40 7.70 9.60 12053
12054 Take up and set aside for re-use ditto................................................................ 3.80 4.50 5.10 7.00 7.70 8.30 9.60 11.50 12054
12055 Add to either of Items 12053 to 12054 inclusive for breaking
out and clearing away concrete bed and surround if any.................................. 7.30 8.40 12.50 17.80 7.30 8.40 12.50 17.80 12055
12056 Lay only pipe in trench as cable duct................................................................ 9.40 18.80 27.20 41.80 10.50 20.90 31.40 47.10 12056
CONCRETE BEDS FOR CABLE DUCT PIPES Width of concrete bed and pipe bore (mm)
400 450 600 700 800 950
Concrete Grade 10S, Grade 10D or 10MPa in : - Wide Wide Wide Wide Wide Wide
under under under under under under
100 150 two 100 two 150 three 100 three 150
pipe pipe pipes pipes pipes pipes
A B C D E F
Per linear metre $ $ $ $ $ $
12057 Bed 100 mm thick under pipe or pipes laid side-by-side including haunching up
from outside edge of bed to meet pipe barrel tangentially after pipes are laid.................................... 39.80 42.80 60.70 73.80 87.30 104.00 12057
12058 Add to Item 12057 if pipe or pipes completely surrounded with
similar concrete not less than 100 mm thick all round......................................................................... 46.00 56.60 67.00 76.30 90.50 119.10 12058
12/13
12 ROADWORK AND CABLE DUCT 12
Item Item
CABLE DUCT (CONT'D)
GRANULAR BEDS FOR CABLE DUCT PIPES
A
Per cubic metre $
12059 Beds, haunching or surrounds to pipe or pipes laid side-by-side................................................................................................................................................... 190.50 12059
DRAW-IN PITS Internal girth (m)
Exc. Exc. Exc.
n.e. 2.44 3.05 3.66
2.44 but n.e. but n.e. but n.e.
3.05 3.66 4.27
A B C D
Each $ $ $ $
12060 Excavate temporary cable draw-in pit n.e. 450 mm deep, deposit surplus material on Site or
cart away to dump, maintain sides and backfill with clean sand after cable being laid.......................................................... 24.40 29.40 48.90 58.60 12060
12061 Ditto but 450 - 600 mm deep.................................................................................................................................................... 29.40 39.10 58.60 78.20 12061
12062 Ditto but 600 - 750 mm deep.................................................................................................................................................... 39.10 48.90 78.20 107.50 12062
12063 Permanent draw-in pit n.e. 450 mm deep internally (from top of base slab to top of cover slab)
constructed of concrete Grade 20S, Grade 20D or 20MPa with 200 mm base slab, 150 mm thick
walls and 100 mm thick precast concrete Grade 20S, Grade 20D or 20MPa cover slab extending
to outer face of walls and reinforced with and including 10 mm diameter steel rods at 150 mm centres
both ways, and set flush with surrounding paving and jointed against the same with mastic, including
all necessary excavation, disposal of surplus material on Site or cart away to dump, formwork,
leaving 50 mm diameter hole through base slab, forming 450 x 450 x 300 mm deep soakaway
sump under and filling the same with 50 mm gauge broken stone, and filling pit with dry sand after
cable being laid if ordered......................................................................................................................................................... 387.80 463.40 576.90 718.70 12063
12064 Ditto but 450 - 600 mm deep internally.................................................................................................................................... 605.20 709.30 888.90 1,078.10 12064
12065 Ditto but 600 - 750 mm deep internally.................................................................................................................................... 728.20 841.70 1,040.20 1,267.20 12065
MARKER SLABS
A
Each $
12066 Precast concrete Grade 20S, Grade 20D or 20MPa marker slab, size 225 x 200 mm and 100 mm thick trowelled smooth with
letters or numbers formed in top surface as ordered, and with two 6 mm diameter steel rods cast in and left projecting 225 mm
as anchor rods including setting in position flush with ground level over temporary draw-in pit or cable trench....................................................................... 28.40 12066
12/14
Section 13
PLUMBING AND DRAINAGE
13 PLUMBING AND DRAINAGE 13
SECTION 13
PLUMBING AND DRAINAGE
SPECIAL CONDITIONS
Specification SC13.01 This Section shall generally be read and used in conjunction with the Specification in particular
the Particular Specification for Plumbing and Drainage Installation and any other relevant
Particular Specifications adopted in the Contract.
Due allowance is deemed to have been made in the Contract Percentages and any percentage
addition adjustment to any of the rate contained in this Section or other Sections in the
Schedule for any difference in cost and expenses incurred for complying with all requirements
as stipulated in the Specification and Employer's Requirements adopted in the Contract for
the Plumbing and Drainage Installation (the Installation).
PLUMBING AND DRAINAGE INSTALLATION
Measurement SC13.02 Pipe sizes are referred to nominal sizes .
generally
Pipes shall generally be measured the length along centre line of the pipework over all in-line
fittings including bends, branches, junctions and the like unless otherwise provided.
All underground drain pipes shall be measured net as laid or fixed over all fittings.
Gutters shall be measured the net length as fixed. No allowance for laps shall be measured.
Insulation to pipe shall be measured the diameter of the pipes to be insulated.
Measurement SC13.03 Only fittings over 50 mm diameter, or 54 mm diameter in the case of copper fittings, shall
of fittings be measured separately. All fittings shall be identified by the largest diameter.
Unless otherwise stated, fittings shall be measured as Extra over the gutter, tubing or pipe
run.
Taper pipes, taper bends, tees and junctions with diminishing branches shall be measured
as the size of the largest end.
Connector shall include valve connector, press fitting, flat seal etc. and the like, female or
male construction. Connector shall only be measured in the connections of pipework to
water tanks, cisterns and the like, and connections between new and existing pipework.
Connectors in new pipework is deemed to be included in the measurement of pipes.
Elbow shall include all degree elbow, reducing elbow, pre-formed pipe bridge, adapter,
with or without sort, plain end, wall plate, outlet, etc. and the like, female or male construction.
Tee shall include equal tee, branch tee, reducing tee, with or without outlet, etc. and the
like, female or male construction.
All stainless steel pipe fittings shall include press fitting and any other construction
recommended by the manufacturer.
13/1
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
Measurement SC13.04 Sheet lead shall be measured the net weight as laid or fixed. The weight of tacks,
of sheet lead wedges and the like shall be added in.
work
Measurement SC13.05 Unless specifically included in the items under this Section, the following works shall be
under separate measured separately and paid for at the appropriate rates under the respective Sections as
Sections stated below or other applicable Work Sections in this Schedule : -
(a) All trench excavation under Section 03 - Excavation.
(b) All chases in and holes through existing walls, ceilings, etc. for tubing and pipes,
other than mortices or holes for brackets, and all concrete filling under Section 04
- Concrete Work and Section 05 - Brickwork and Blockwork.
(c) All steel reinforcement and joist under Section 04 - Concrete Work and Section
10 - Steel and Metal Work.
(d) All plasterwork under Section 11 - Plastering and Finishes.
(e) All painting to pipework under Section 15 - Painting.
Measurement SC13.06 The measurement shall be the compacted thickness as specified by the Maintenance
of granular Surveyor, whether laid in one or more layers. No deduction shall be made for voids not
bedding for exceeding 1.00 m.
drain pipes
Measurement SC13.07 Formwork shall be measured as the actual surface in contact with concrete. No deduction
of formwork shall be made for openings not exceeding 1.00 m. Boxing for opening exceeding 1.00 m
shall be measured as edges. Wrot formwork shall be measured only when a fair finished
face to the concrete is specifically ordered by the Maintenance Surveyor in writing.
Measurement SC13.08 Precast concrete shall be measured the actual size of the item casted.
of precast
concrete
Measurement SC13.09 Manholes, cesspits, etc. shall be measured net as cast.
of manholes,
cesspits, etc. No deduction shall be made for : -
(a) Voids not exceeding 0.05 m.
(b) The volume of reinforcement, steel joist and the like.
(c) Openings in walls, cover slabs and the like not exceeding 0.10 m.
13/2
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
Measurement SC13.10 Preparation and applying internal lining to leaking buried water-carrying services measured
of internal the number of the net length of pipes over all fittings and joints not exceeding 2500 mm
lining to long. Length exceeding 2500 mm shall be measured the net length of pipes over all fittings
leaking buried and joints. The material and length of internal lining shall be submitted for the Maintenance
water-carrying Surveyors approval before formal application.
services
Rates for SC13.11 Rates for Plumbing and Drainage Installation shall generally include for :-
Plumbing and
Drainage (a) Carrying out all necessary preparation and investigation to the Site and the areas
Installation or services that may be affected by the works prior to commencement of the
Installation.
(b) Working internally or externally.
(c) Submission of technical literatures, catalogues, sample boards, samples, etc. for
the approval of the Maintenance Surveyor.
(d) Provision of proper and safe protection of equipment, materials delivered to Site
and any installation works executed.
(e) Provision of cleaning and disinfection of the Installation upon completion using
methods as specified in the Contract.
(f) Works executed by Specialist Sub-contractor approved by the Maintenance
Surveyor.
(g) Provision of design and record drawings except for installation drawing and as-built
drawing preparation which are part of the services provided for the Enhanced Execution
Works for the Plumbing and Drainage Installation under Special Conditions Clause
SC13.36(a) herein, in which case, the drawing preparation shall be measured
and paid for separately in accordance with Special Conditions Clauses SC13.40
to SC13.41 herein.
(h) Programming, planning, co-ordination, control, supervision, monitoring and phasing
of installation works in existing and/or occupied buildings and premises including
providing all necessary superintendents as required and specified in the Contract.
(i) Provision of temporary works and protective measures for execution of works in
existing and/or occupied buildings or premises to suit users and/or building
management requirements, including the erection, alteration and dismantling of
such temporary works and protective measures on a daily basis.
(j) Temporary suspension of the water supplies and arranging for temporary plumbing
system and diversion, if required.
(k) Conduct sampling and analysis of potable fresh water upon substantial completion
of the plumbing installation.
(l) Carrying out cleaning of the plumbing installation pipework and water storage
tanks and disinfection of plumbing installation in potable use.
13/3
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
Rates for SC13.11 (m) Carrying out all testing and commissioning for the Installation as required under the
Plumbing and (Cont'd) Contract including provisions of all incidental sundry components for operation of the
Drainage Installation to the satisfaction of the Maintenance Surveyor.
Installation
(Cont'd)
Rates for lead SC13.12 Rates for lead work shall include for all dressing, bossing up, forming angles and inter-
work sections, bossing ends and the like to rolls and welts.
Rates for SC13.13 The rates for pipeworks shall further include for : -
pipeworks
(a) All short lengths, cutting and waste.
(b) All joints in the running lengths including flanges, couplings, unions, or other
connection device, cutting and jointing pipe to fittings like bends, elbows,
branches, tees, caps, heads, outlets, gullies, etc., joints between pipes of differing
materials, including using all necessary jointing materials and fixing accessories.
(c) All connections of pipework to water tanks, cisterns and the like including drilling
of tank, cistern, etc. as required, and connections between new and existing
pipework including all necessary jointing materials and fixing accessories, cutting
into existing pipework and removing short length of pipe in position, and
preparing and making good pipe ends to receive new fittings.
(d) Fittings for pipes not exceeding 50 mm diameter (or 54 mm diameter in the case of
copper pipes) including connections.
(e) Provision and fixing of all pipe sleeves of any kind of materials including loose
cover plates, pointing with approved sealants, sealing up voids between pipes and
fire rated walls or floors with sealing system as specified.
(f) Provision and fixing of pipe supports including stainless steel clamps, brackets,
clips, etc. as specified .
(g) Fixing in any position to floors, walls and soffits including fixing in chases, ducts,
false ceilings and similar positions, and laying in trench.
(h) Protection of underground and concealed metal pipes with Denso tape or other
materials as specified.
(i) Provision of connection point for the purposes of connection of equipotential
bonding connection as required by the I.E.E. Regulations.
(j) Making good to any length of pipe damaged in addition to the net length which
has actually been removed, including providing new pipes and forming and
including new joints.
(k) Making good all surfaces disturbed.
13/4
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
Rates for SC13.14 The rates for all types of drain pipes for underground drainage shall further include for : -
drain pipes for
underground (a) All jointing including provision of loose collars, loose sockets, connectors, flanged
drainage socket ends, flanged spigot ends and the like and jointing materials.
(b) Provision and fixing of all holderbats required for pipes fixed to manhole sides and
the like and making good.
(c) Building in ends of pipes to manhole sides and the like, jointing to channels and
making good.
(d) Temporary sealing of pipes during the progress of the work.
(e) Making good to any length of drain pipe damaged in addition to the net length
which has actually been removed, including providing new drain pipes and
forming and including new joints.
(f) Maintaining the soil or waste flow by means of temporary channels or drain pipes
whilst the work is in progress, including additional excavation or other related
works.
(g) Making good of surfaces disturbed.
Rates for SC13.15 The rates for sub-soil drain pipes shall further include for : -
sub-soil drain
pipes (a) Forming holes in pipeline for junction if required.
Rates for SC13.16 The rates for vitrified clay pipes shall further include for : -
vitrified clay
pipes (a) Providing extra strength o ring flexible spigot and socket joints.
Rates for SC13.17 Rates for UPVC pipes, polyethylene (PE) pipes, galvanized mild steel pipes, uPVC lined
tubing and galvanized mild steel pipes, stainless steel pipes and copper pipes shall further include for
pipes include made bends.
for made
bends
Rates for SC13.18 Rates for fittings on gutters, tubing and pipes of all types shall include for : -
fittings
(a) Additional cutting and waste on gutter, tubing or pipe and all extra joints.
(b) In the case of pipe bends and gutter angles, bends and gutter angles of any angle.
(c) In the case of tees, crosses and single or double junctions, square or oblique
connections with straight or curved offsets and all ends either equal or reducing.
13/5
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
Rates for SC13.19 The rates for take up or take down and clear away or take up or take down and set aside
take up or for re-use gutters, tubing or pipes shall further include for : -
take down,
etc. gutters, (a) All fittings including brackets or hangers.
tubing or pipes
(b) Cutting into existing gutter, tubing or pipe in position.
(c) Preparing remaining ends to receive joint with new pipe if required.
(d) Plugging ends with plugs or caps as required.
(e) Making good surfaces disturbed.
(f) Arranging for temporary plumbing system and diversion, if required.
Rates for SC13.20 The rates for fix only or lay only gutters, tubing or pipes shall further include for : -
fix only
or lay only (a) All fittings including brackets, gaskets, bolts, nuts and washers and other
gutters, tubing accessories.
or pipes
(b) Cutting mortices and grouting in cement mortar.
(c) Preparing ends to receive joints with pipes.
(d) Making good surfaces disturbed.
Rates for SC13.21 The rates for insulation to pipeworks and cylinders shall include for : -
insulation
(a) All cutting, waste and fitting.
(b) Fixing bands.
Rates for SC13.22 The rates for cisterns and tanks shall include for : -
cisterns and
tanks (a) Supply and installation in accordance with the manufacturer's instructions.
(b) Provision of design for glass-fibre reinforced plastic water tanks.
(c) Suitable for storage of fresh water, portable water and/or flushing water.
(d) Any colour and shape.
(e) Supply and fix nozzles, air vent, electrode seat and cover, internal ladder, external
ladder, galvanized mild steel base supporting frames, etc. and all necessary
accessories, fittings and the like recommended by the manufacturer.
13/6
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
Rates for SC13.22 (f) Providing and fixing with anchor bolts.
cisterns and (Cont'd)
tanks (g) Cutting mortice, sinking or drilling in concrete, brick, stone or other surfaces as
(Cont'd) required.
(h) Grouting into new or existing mortice or holes.
(i) Making good disturbed surfaces.
(j) Masking, protecting and cleaning.
(k) Submission of catalogues, technical literature, operation manuals and
manufacturer's guarantee for the approval of the Maintenance Surveyor.
(l) Testing and commissioning.
(m) Providing test certificate.
Rates for SC13.23 The rates for pressure vessels shall further include for : -
pressure
vessels (a) Supply and installation in accordance with the manufacturer's instructions.
(b) Providing and fixing all accessories, fittings and the like as recommended by the
manufacturer.
(c) Any colour and shape.
(d) Providing and fixing with anchor bolts.
(e) Cutting mortice, sinking or drilling in concrete, brick, stone or other surfaces as
required.
(f) Grouting into new or existing mortice or holes.
(g) Making good disturbed surfaces.
(h) Masking, protecting and cleaning.
(i) Submission of catalogues, technical literature, operation manuals and
manufacturer's guarantee for the approval of the Maintenance Surveyor.
(j) Testing and providing test certificates.
(k) Providing Statutory Inspection Certificate.
Rates for SC13.24 The rates for concrete beds, haunchings and surrounds to pipes shall include for : -
concrete beds,
haunchings (a) Providing and laying a layer of polythene sheeting or concrete blinding on the
and surrounds bottom of trenches before concreting.
to pipes
(b) All necessary formwork and falsework.
13/7
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
Rates for SC13.24 (c) Forming flexible joints including joint filler.
concrete beds, (Cont'd)
haunchings (d) All necessary precast concrete wedges, blocks or cradles or other approved pipe
and surrounds supports including compressible sheeting.
to pipes
(Cont'd) (e) Keeping concrete and pipes damp until backfilling placed.
Rates for SC13.25 The rates for granular beds shall include for : -
granular beds
(a) Recycled or non-recycled granular bedding material to be clean, hard, durable,
crushed rock or crushed concrete, broken stone, hard brick, concrete or other
comparable hard insert approved by the Maintenance
Surveyor.
(b) Compacting and trimming granular beds to correct gradient and shape under
barrel and pipe sockets.
(c) Handling from temporary spoil heaps.
(d) Additional bulk of material required to allow for compaction and consolidation.
(e) Re-compacting and laying granular around pipes after testing.
Rates for SC13.26 The rates for traps and gullies of any type shall include for : -
traps and
gullies of (a) All necessary concrete bedding, cover and surrounds including formwork.
any type
(b) Excavation, backfilling with suitable materials, compaction and removal of surplus
excavated materials from Site.
(c) Building in ends of pipes to gully sides and the like.
(d) Connecting and jointing to drainage system.
Rates for SC13.27 The rates for surface water channels or step channels shall include for : -
surface water
channels or (a) Excavation, backfilling with suitable filling materials, compaction and removal of
step channels surplus excavated materials from Site.
(b) All necessary formwork.
(c) Forming and including movement joints, angles, ends, intersections, junctions,
outlets, rebates to receive channel covers and the like.
(d) Rendering all exposed surfaces with minimum 13 mm thick cement and sand (1:3)
mortar.
(e) Providing and forming PVC weepholes, if required.
(f) Connecting and jointing to drainage system.
13/8
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
Rates for SC13.28 The rates for cast iron channel covers shall include for : -
cast iron
channel (a) Multi-handling and placing in position.
covers
(b) All necessary cutting and waste.
(c) Adjusting to suit channel alignment.
Rates for SC13.29 The rates for precast concrete channel covers shall include for : -
precast
concrete (a) Forming slots to channel covers.
channel
covers (b) Multi-handling and placing in position.
(c) All necessary formwork.
(d) All necessary cutting and waste.
(e) Adjusting to suit channel alignment.
Rates for SC13.30 The rates for manholes, cesspits, etc. shall include for : -
manholes,
cesspits, etc. (a) Tamping around reinforcement.
(b) Rendering all internal surfaces with minimum 13 mm thick cement and sand
(1:3) mortar.
(c) Forming benching for main and branch channels as required including finishing to
falls.
(d) Benching finishing smooth and marrying into structural sides with cement
mortar (1:3).
(e) Fair-faced finish internally.
(f) Testing of water tightness.
Rates for SC13.31 The rates for formwork shall include for : -
formwork
(a) Submission of design on formwork and falsework, if any, including supports and
foundations by a Registered Structural Engineer.
(b) Erecting, maintaining and striking formwork and falsework.
(c) Preventing loss of grout between joints.
(d) Fixing inserts and chases.
(e) Box out to form holes not exceeding 1.00 m.
(f) Preparing and applying surface retarders and release agents as required.
13/9
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
Rates for SC13.31 (g) Multi-handling of removing formwork and falsework when striking without
formwork (Cont'd) overloading the finished concrete work.
(Cont'd)
(h) Preparing and applying wood preservatives to all surfaces of left-in timber
formwork.
(i) Forming cambers and falls.
(j) Individual fillets, chambers, splays, drips, rebates, recesses, grooves and the like,
not exceeding 100 mm total girth measured on the faces in contact with the
concrete.
(k) Strutting to soffits at any height.
(l) Soffits of solid slabs in any thickness.
(m) Sides and soffits of beams in any depth.
(n) In case of formwork materials proposed by the contractor, all necessary
preparation work other than spatterdash.
Rates for SC13.32 The rates for manhole or gully sump cover and frame shall include for : -
manhole or
gully sump (a) Bedding frame in cement and sand (1:3) mortar.
cover and
frame (b) Sealing cover in heavy grease.
(c) Providing two keys for each pattern of cover.
Rates for SC13.33 The rates for alterations to existing manholes shall include for : -
alterations
to existing (a) All preparation work that are required for the alteration.
manholes
(b) Forming main and branch channels as required in re-formed benching including
finishing to falls.
(c) Provision of temporary channels or drain pipes and/or other temporary measures
necessary to maintain the existing soil or waste flow whilst the work is in progress.
(d) All other related works that are required for the alteration.
(e) Clearing away debris arising from alteration work.
(f) Making good areas disturbed to match existing.
Rates for SC13.34 The rates for internal lining to leaking buried water-carrying services shall include for : -
internal lining
to leaking (a) Removing covers of manholes and other drainage chambers and re-fixing
buried water- including heavy grease after cleaning.
carrying
services
13/10
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
Rates for SC13.34 (b) Cleaning of all pipelines and drainage structures with high pressure water jets
internal lining (Cont'd) before application of internal lining including removing all water arising and drying
to leaking up the pipelines and drainage structures before execution of works.
buried water-
carrying (c) Application to all types of pipe materials including fittings.
services
(Cont'd) (d) Temporary diversion of drainage flow.
(e) Establishment, maintaining and removal of all necessary plant, tools and
equipment.
(f) Testing as specified, remedying any defects and re-testing as necessary until the
Maintenance Surveyor satisfies the test results.
(g) Providing two sets of CD-ROM recording of the repaired pipelines certified
by the Contractors Leakage Test Team Leader and Contract Manager.
(h) Submission of catalogues, technical literature, etc. for the approval of the
Maintenance Surveyor.
G.S. clauses for SC13.35 G.S. clauses for formwork can be found in the Concrete Work Section of the General
formwork Specification for Building.
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION
Services SC13.36 Services for Plumbing and Drainage Installation in this Section shall refer to the following
generally services to be provided by the Contractor in connection with the Plumbing and Drainage
Installation, all in accordance with the requirements of the Contract : -
(a) Services provided for the Enhanced Execution Works ("EEW") for the Plumbing
and Drainage Installation.
(b) Services provided to fresh water plumbing system and successful application of
new or renewal certificates under the Quality Water Recognition Scheme
("QWRS") for Buildings (the Scheme).
(c) Services provided for cleaning and clearance of existing underground foul and
waste water drainage system at market complexes and cooked food centres.
(d) Services for inspection, testing and cleaning of existing drainage system.
Any services or works required for the satisfactory completion and operation of the
Plumbing and Drainage Installation in accordance with the requirements of the Contract
but are not separately itemized under the Services for Plumbing and Drainage Installation
in this Section, the Contractor is deemed to have allowed for such item(s) in his Contract
Percentages and any percentage addition to the rates contained in this and other Sections
in the Schedule of Rates under the Contract.
13/11
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION
Services for SC13.37 Services provided for the Enhanced Execution Works for the Plumbing and Drainage
Enhanced Installation shall include for any of the following services : -
Execution
Works (a) Submission of installation drawings prior to commencement of the Installation for
the approval of the Maintenance Surveyor.
(b) Submission of as-built drawings upon completion of the Installation for the
approval of the Maintenance Surveyor.
(c) Submission of operation and maintenance (O&M) manual upon completion of
the Installation for the approval of the Maintenance Surveyor.
(d) Providing specific operation and maintenance services for the completed Plumbing
and Drainage Installation.
Measurement SC13.38 The items included under Services for Plumbing and Drainage Installation shall only be
of Services for measured and paid for where specifically ordered by the Maintenance Surveyor in writing.
Plumbing and
Drainage
Installation
Measurement SC13.39 Measurement of the Services for the Enhanced Execution Works will be based on the final
of Services for value of the Installation included in the Works Order (but excluding the value of the services
Enhanced ordered for the EEW of such Installation) that has been certified by the Maintenance
Execution Surveyor (the "Installation Value").
Works
Measurement SC13.40 The provision for installation drawings shall be measured and paid for when the complete
of installation set of drawings and/or documents for the Installation has been submitted and accepted by
drawings the Maintenance Surveyor.
Measurement SC13.41 The provision for as-built drawings shall be measured and paid for when the drawings
of as-built have been submitted and accepted by the Maintenance Surveyor.
drawings
Measurement SC13.42 The provision for operation and maintenance (O&M) manuals shall be measured and paid
of O&M for when the O&M manual have been submitted and accepted by the Maintenance
manual Surveyor.
13/12
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION
Measurement SC13.43 Measurement of provision of inspection to fresh water plumbing system is based on the
of Inspection following : -
to Fresh Water
Plumbing System (a) The function / type of building to be inspected; and where the building is of a
mixed function, the dominant function of the building.
(b) The number of floors of the building to be inspected including any basement
floor(s), ground floor, sky garden floor and/or refuge floor(s), irrespective of the
storey height of each floor.
(c) Inspection to fresh water plumbing system shall be measured as number of
inspection.
(d) Any return visits due to attending follow-up actions from matters arising from the
inspection, as measured in sub-clause (c) above, shall be deemed included in the
same inspection, and such return visits shall not be measured separately.
The term "floor" in sub-clause (b) above shall mean the structural floor excluding any
mezzanine floor(s), catwalk, metal walkways, floating floors and the like, which shall not
be measured.
Lift machine room(s), fire escape staircase enclosures and mechanical plant room(s)
located at roof level shall not be measured.
Unless otherwise stated, if the building consists of an annex block, then only the main
building will be considered in the measurement which shall be measured based on the
number of floors of the main building.
If the annex block consists of an independent fresh water plumbing system, in which case,
measurement of the number of floors of the annex block shall be measured separately as if
it is a stand-alone building.
If it is not reasonable to identify which of the buildings is the main building and where more
than one building is jointed together, and provided that these buildings are served with the
same fresh water plumbing system, then only the building with the highest number of floors
will be measured once.
Measurement SC13.44 Measurement of utilities survey of the buried/exposed existing underground utilities /
of utilities services shall be the plan area within boundary as directed by the Maintenance Surveyor
survey inclusive of all terrains and irregularities, etc. and measured flat. Measurement shall either
be taken at the date of commencement or at the date of completion or both as agreed by
the Maintenance Surveyor.
Measurement SC13.45 Measurement of acoustic test for detection of leaking buried water pipes shall be the plan
of acoustic test length within boundary as directed by the Maintenance Surveyor inclusive of all terrains
for detection of and irregularities, etc. and measured flat. Measurement shall either be taken at the date of
leaking buried commencement or at the date of completion or both as agreed by the Maintenance
water pipes Surveyor.
13/13
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION
Measurement SC13.46 CCTV inspection survey carried out as part of the cleaning and clearance work of the
of CCTV underground foul and waste water drainage system and grease tanks at market complexes
inspection and cooked food centres shall not be measured separately.
survey
Rates for SC13.47 The rates for Services for Enhanced Execution Works for the Plumbing and Drainage
Services for Installation shall further include for :-
Enhanced
Execution (a) Submission of a detailed programme of the Installation showing the intended method,
Works stages and order of work execution for the approval of the Maintenance Surveyor.
(b) Submission of full details of builder's work requirements for the approval of the
Maintenance Surveyor.
For any works or services that are required in the Specification for Enhanced Execution
Works for Plumbing and Drainage Installation but are not separately itemized in this Section,
the Contractor is deemed to have allowed such works or services in the Contract Percentages
and any percentage addition for complying with the Specification requirements.
Rates for SC13.48 The rates for provision of installation drawings shall further include for : -
provision of
installation (a) Developing, preparing and completion of drawings showing the complete installation
drawings requirements incorporating the following details and other details as specified : -
- Installation drawings
- Pipework installation drawings
- Special plant rooms co-ordination work
- Builder's work drawings
- Manufacturer's shop drawings
- Checking drawings of other trades
(b) Reviewing, updating and revising the drawings taking into account comments from the
Maintenance Surveyor and/or changes of the works during the Contract.
(c) Provision of drawings in electronic format conforming to the latest version of CAD
Standard of Works Projects as specified.
(d) Submission of the number of copies of drawings as required by the Contract.
13/14
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION
Rates for SC13.49 The rates for provision of as-built drawings shall further include for : -
provision
of as-built (a) Developing, preparing and completion of drawings showing the as-built condition
drawings of the Installation incorporating the details as required by the Contract.
(b) Reviewing, updating and revising the drawings taking into account comments from
the Maintenance Surveyor and/or changes of the works during the Contract.
(c) Submission of the number of copies of drawings as required by the Contract.
(d) Provision and installation of a glass frame for the valve chart and plant room
record drawings at major plant rooms.
Rates for SC13.50 The rates for provision of O&M manual shall further include for : -
provision
of O&M (a) Developing, preparing and completion of the O&M manual showing the detailed
manual technical information covering both operation and maintenance aspects of the
Installation as required by the Contract.
(b) Reviewing, updating and revising the O&M manual taking into account comments
of the Maintenance Surveyor and/or changes of the works during the Contract.
(c) Submission of the number of copies of the O&M manual as required by the Contract.
Rates for SC13.51 The rates for provision for annual operation and maintenance services shall further include
provision of for : -
annual
operation and (a) Submission of a maintenance schedule identifying the programme for monthly
maintenance routine service, quarterly, half-yearly and annual operation and maintenance
services services, all to the approval of the Maintenance Surveyor.
(b) Carrying out monthly routine maintenance services, quarterly, half-yearly and
annual operation and maintenance services, as detailed in the Contract and to the
satisfaction of the Maintenance Surveyor.
(c) Provision of emergency call-out services for any installation and equipment failure.
(d) Carry out replacement or repair of all components of equipment and
pipework as necessary in order to maintain the whole Installation in a good
working order including supply of equipment, fittings and consumable items.
(e) Maintaining an attendance log book and details of operation and maintenance
services carried out.
(f) Carrying out checking and, if necessary, re-adjustment of the Installation one
month before the expiry date of the Maintenance Period.
13/15
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION
Rates for SC13.52 The rates for carrying out inspection to fresh water plumbing system shall further include for : -
inspection to
fresh water (a) Provision of a licensed plumber, building surveyor or building services engineer
plumbing with qualification and experience that meets the requirements as laid down in the
system Fresh Water Plumbing Maintenance Guide issued by Water Supplies Department.
(b) All expenses and reimbursement in connection with employment of the licensed
plumber, building surveyor or building services engineer including but not limited
to basic salary, contribution to the Mandatory Provident Fund, gratuity and all
necessary levies, e.g. Construction Industry Council, insurances, etc.
(c) Carrying out inspection of the fresh water plumbing system in accordance with the
recommended practices as laid down in the Fresh Water Plumbing Maintenance
Guide issued by Water Supplies Department.
(d) Programming, planning, co-ordination and phasing of installation works in existing
and/or occupied buildings and premises.
(e) Provision of temporary works and protective measures for execution of works in
existing and/or occupied buildings or premises to suit users and/or building
management requirements.
(f) Submission of documentary support and inspection results, provision of estimates
for proposed repair works, water tank cleansing reports and other documents
necessary for the new or renewal application under the Scheme as required by
the Maintenance Surveyor.
Rates for SC13.53 The rates for cleaning of water tanks shall include for : -
cleaning of
water tanks (a) Cleaning of water tanks all in accordance with the Specification requirements.
(b) Designating a competent Unit Foreman to supervise throughout the course of cleaning.
(c) Co-ordination with the user or management office in carrying out cleaning works
in existing and/or occupied buildings and premises.
(d) Submitting method statements, plant / equipment lists and risk assessment on the delivery
of cleaning.
(e) Submitting attendance records.
(f) Taking photographic records.
(g) Submitting completion reports including :
(i) attendance records of all skilled labourers;
(ii) photographic records on the locations and distribution of defects found
on the internal wall finishes and/or structure before and after the repairs;
(iii) photographic records after completion of the cleaning services; and
(iv) photographic records to show the proper functioning condition of the
stop valves and stop cocks after completion of the cleaning services.
13/16
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION
Rates for SC13.54 The rates for sampling and analysis for water quality examination shall include for : -
sampling and
analysis for (a) Conducting sampling and analysis for the quality of fresh water on completion of
water quality the plumbing installation. At least one sampling shall be taken from each water
examination supply tank.
(b) All water tests and analysis shall be conducted by an independent accredited
laboratory as stated in the Contract.
(c) Submission of test reports.
Rates for SC13.55 The rates for cleaning and clearance of underground foul and waste water drainage system
cleaning and and grease tanks at market complexes and cooked food centres shall include for : -
clearance of
underground foul (a) Designating a competent Unit Foreman to supervise throughout the course of
and waste water cleaning and clearance;
drainage system
and grease tanks (b) Co-ordination with the user or management office in carrying out cleaning works
at market in existing and/or occupied buildings and premises.
complexes and
cooked food (c) Submitting method statements and risk assessment on the delivery of periodic
centres CCTV inspection survey and cleaning and clearance of the underground foul
and waste water drainage system and grease tanks.
(d) Submitting completion reports including :
(i) attendance records of all skilled labourers;
(ii) photographic records to substantiate the provisions of plant/equipment,
labours and conditions of all manholes and grease tanks before and after
the cleaning and clearance services;
(iii) submitting CCTV inspection survey reports after the cleaning and
clearance services; and
(iv) layout plans with records of the routing of all underground drainage pipes
and the locations of all manholes and grease tanks.
Rates for SC13.56 The rates for utilities survey of the buried/exposed existing underground utilities/services
utilities shall include for :-
survey
(a) Carrying out the utilities survey of the buried/exposed existing underground
utilities/services by the qualified personnel of an approved independent firm using their
own equipment and providing such labour and assistance as may be required.
(b) Preparation and submission of survey report in 2 copies with record drawings,
photo records, text reports and layout plans and 2 sets of CD-ROM containing
all such information.
(c) Compliance with the requirements of the current Code of Practice on Monitoring
and Maintenance of Water Carrying Services Affecting Slopes issued by Civil
Engineering and Development Department.
13/17
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION
Rates for SC13.57 The rates for acoustic test for detection of leaking buried water pipes shall include for :-
acoustic test
detection (a) Carrying out the acoustic test by the qualified personnel of an approved
of leaking independent firm using their own equipment and providing such labour and
buried water assistance as may be required.
pipes
(b) Preparation and submission of survey report in 2 copies with record drawings,
photo records, text reports and layout plans and 2 sets of CD-ROM containing
all such information.
(c) Compliance with the requirements of the current Code of Practice on Monitoring
and Maintenance of Water Carrying Services Affecting Slopes issued by Civil
Engineering and Development Department.
Rate for SC13.58 The rates for cleaning of existing drainage system shall include for : -
cleaning of
existing drainage (a) Cleaning of existing manholes including branches and drains between manholes,
system cesspits, septic tanks, catch pits, grease pits and other drainage chambers.
(b) Removing covers and re-fixing including re-sealing with heavy grease after
cleaning out works.
(c) Removing all sludge, silts, solid matters, etc. and the like by labour or pumping
out from drainage chamber.
(d) Clearing away and disposal of sludge, deposits, solid matters, etc. to the dumping
site approved by Environmental Protection Department.
(e) Cleaning of drainage chamber with high pressure jets including removing all water
arising.
(f) Obtaining a disposal permit from Environmental Protection Department and
submitting a copy to the Maintenance Surveyor.
(g) Keeping surrounding and affected areas clean and tidy including sanitizing,
cleaning, removing all matters arising.
Rates for SC13.59 The rates for CCTV inspection survey to existing underground drainage system shall
CCTV include for : -
inspection
survey to (a) Cleaning all pipelines and drainage structures with high pressure water jets before
existing testing.
underground
drainage system (b) Providing two copies of CCTV inspection survey reports and two sets of 3R-size
digital colour photographs of all identified defects.
(c) Providing two sets of CD-ROM recordings of all drains, manholes, cesspits,
septic tanks, catch pits, grease pits and other drainage chambers inspected.
13/18
13 PLUMBING AND DRAINAGE 13
SPECIAL CONDITIONS
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION
Rates for SC13.60 The rates for testing existing drains shall include for : -
testing
existing (a) Cleaning all pipelines and drainage structures with high pressure water jets before
drains testing.
(b) Temporary sealing ends of drains and connections.
(c) Provision of all water, material and equipment.
(d) Provision of test record.
13/19
13 PLUMBING AND DRAINAGE 13
Item Item
LEAD WORK Take Take
Supply down down Fix
Milled lead and all labours including provision of all nails, screws, holdfasts, wedges, and and and set only
tacks and solder in : - fix clear aside for
away re-use
A B C D
Per kg $ $ $ $
13001 Flats (including rolls), gutters (including cesspools), cornices, dormers, flashings, hips, ridges,
linings to sinks, cisterns, safes, drawers and the like .............................................................................................................. 71.50 6.40 7.70 13.20 13001
DUCTILE IRON PIPES AND FITTINGS FOR WATER SUPPLY SYSTEM
Pipe diameter (mm)
Ductile iron pipes and fittings to BS EN 545: 2010 with internal cement lining, for fresh and flushing water system : - 80 100
A B
Per linear metre $ $
13002 Pipe laid in trench......................................................................................................................................................................................................... 477.20 488.90 13002
13003 Pipe fixed to floor, wall or soffits................................................................................................................................................................................. 495.40 510.70 13003
Each
13004 Extra over pipe for cover plate to flanged end ............................................................................................................................................................. 67.00 81.30 13004
13005 Ditto for flanged socket end ......................................................................................................................................................................................... 324.90 489.00 13005
13006 Ditto for flanged spigot end ......................................................................................................................................................................................... 225.50 308.50 13006
13007 Ditto for flanged connector to existing pipework or water tank, etc............................................................................................................................ 284.50 343.90 13007
13008 Ditto for bend ............................................................................................................................................................................................................... 219.30 300.50 13008
13009 Ditto for tee ................................................................................................................................................................................................................... 337.50 444.10 13009
13010 Ditto for cross ............................................................................................................................................................................................................... 503.90 671.60 13010
Per linear metre
13011 Take up and clear away pipe laid in trench excavation (trench excavation measured separately) ............................................................................ 8.90 10.90 13011
13012 Take up and set aside for re-use pipe laid in trench (ditto) ......................................................................................................................................... 11.50 13.40 13012
13013 Take down and clear away pipe fixed to floor, wall or soffits .................................................................................................................................... 9.60 11.50 13013
13014 Take down and set aside for re-use pipe fixed to floor, wall or soffits ....................................................................................................................... 11.50 13.40 13014
13015 Lay only pipe in trench ................................................................................................................................................................................................. 35.30 37.10 13015
13016 Fix only pipe to floor, wall or soffits ........................................................................................................................................................................... 48.60 51.20 13016
Each
13017 Unbolt existing joint, remove gasket and clear away, clean flange faces, provide new gasket and re-bolt joint ...................................................... 48.60 54.80 13017
13018 Remove flange cover plate and clear away, clean flange face, provide new gasket and prepare
end of existing pipe for jointing to new pipework (measured separately)................................................................................................................... 45.90 51.20 13018
13/20
13 PLUMBING AND DRAINAGE 13
Item Item
UPVC LINED GALVANIZED MILD STEEL PIPES AND FITTINGS FOR WATER SUPPLY SYSTEM
UPVC lined galvanized steel pipes
and fittings to BS 1387:1985 with
internal lining of an approved Pipe diameter (mm)
type for fresh water supply system : - 15 20 25 32 40 50 65 80 100 125 150
A B C D E F G H I J K
Per linear metre $ $ $ $ $ $ $ $ $ $ $
13019 Pipe laid in trench........................................ 89.70 98.20 106.70 127.80 147.00 179.40 251.20 305.30 399.20 539.00 614.60 13019
13020 Pipe fixed to floor,
wall or soffits............................................... 91.20 102.00 112.70 135.70 158.30 195.20 270.50 335.50 433.50 507.00 580.50 13020
Each
13021 Extra over pipe for cap end
or plug.......................................................... - - - - - - 101.70 123.10 164.60 241.60 318.60 13021
13022 Extra over for bend or elbow....................... - - - - - - 149.10 193.50 321.60 509.90 597.10 13022
13023 Ditto for three-way elbow
or tee............................................................. - - - - - - 119.50 152.00 226.20 316.20 409.30 13023
13024 Ditto for cross............................................... - - - - - - 178.80 221.10 359.30 620.70 831.90 13024
13025 Ditto for reducer........................................... - - - - - - 210.40 260.90 372.00 407.50 451.60 13025
13026 Ditto for connector to existing
pipework or water tank, etc......................... - - - - - - 54.30 69.10 102.80 143.70 186.10 13026
Per linear metre
13027 Take up and clear away
pipe laid in trench (trench
excavation measured
separately).................................................... 1.90 2.60 3.20 3.80 4.50 5.10 5.70 6.40 7.00 8.90 10.90 13027
13028 Take up and set aside for
re-use pipe laid in trench
(ditto)............................................................ 3.20 3.80 4.50 5.10 5.70 6.40 7.00 7.70 8.30 10.20 12.10 13028
13029 Take down and clear away
pipe fixed to floor, wall or soffits................ 2.60 3.20 3.80 4.50 5.10 5.70 6.40 7.00 7.70 9.60 12.80 13029
13030 Take down and set aside for
re-use pipe fixed to floor,
wall or soffits............................................... 3.20 3.80 4.50 5.10 5.70 7.00 7.70 8.30 10.20 11.50 13.40 13030
13031 Lay only pipe in trench................................ 4.40 5.30 6.20 7.10 8.00 9.70 10.60 11.50 12.40 13.20 15.00 13031
13032 Fix only pipe to floor,
wall or soffits............................................... 6.20 8.00 8.80 10.60 12.40 14.10 15.00 15.90 19.40 21.20 23.80 13032
13/21
13 PLUMBING AND DRAINAGE 13
Item Item
COPPER PIPES AND FITTINGS FOR WATER SUPPLY SYSTEM
Copper pipes and fittings to BS EN 1057: 2006 with
amendment A1: 2010 insulation polyethylene sheath, Pipe diameter (mm)
for fresh water supply system : - 15 22 28 35 42 54 67 76 108
A B C D E F G H I
Per linear metre $ $ $ $ $ $ $ $ $
13033 Pipe fixed to floor, wall or soffits ................................................... 97.20 164.40 206.20 259.20 298.30 357.20 421.00 577.90 744.20 13033
Brass "Compression type" fittings : -
Each
13034 Extra over pipe for stop end ........................................................... - - - - - - 179.10 222.70 307.90 13034
13035 Ditto for bend or elbow (copper to copper) .................................... - - - - - - 175.50 195.50 270.60 13035
13036 Ditto (copper to steel) ..................................................................... - - - - - - 360.70 399.60 466.40 13036
13037 Ditto for tee (all ends for copper) ................................................... - - - - - - 239.80 266.10 397.00 13037
13038 Ditto (copper to copper to steel) ..................................................... - - - - - - 397.60 589.30 651.00 13038
13039 Ditto for cross (all ends for copper) ............................................... - - - - - - 501.00 554.90 655.40 13039
13040 Ditto for connector to existing pipework........................................ - - - - - - 109.00 121.00 180.40 13040
13041 Ditto flanged tank connector or double nut tank
connector to existing water tank cistern and the like...................... - - - - - - 576.50 719.80 1,221.00 13041
Brass or copper "Capillary type" fittings : -
Each
13042 Extra over pipe for stop end ........................................................... - - - - - - 94.80 133.30 160.70 13042
13043 Ditto for bend or elbow (copper to copper) .................................... - - - - - - 97.90 138.30 181.10 13043
13044 Ditto (copper to steel) ..................................................................... - - - - - - 188.10 208.50 280.20 13044
13045 Ditto for tee (all ends for copper) ................................................... - - - - - - 403.80 481.10 578.20 13045
13046 Ditto (copper to copper to steel) ..................................................... - - - - - - 338.60 514.60 565.80 13046
13047 Ditto for cross (all ends for copper) ............................................... - - - - - - 371.10 421.30 538.30 13047
13048 Ditto for connector to existing pipework........................................ - - - - - - 183.50 218.70 323.50 13048
13049 Ditto flanged tank connector or double nut tank
connector to existing water tank cistern and the like...................... - - - - - - 634.20 791.80 1,343.10 13049
Per linear metre
13050 Take down and clear away pipe fixed to floor, wall
or soffits .......................................................................................... 1.90 2.60 3.20 3.80 4.50 5.10 5.70 6.40 7.00 13050
13051 Take down and set aside for re-use pipe fixed to floor,
wall or soffits .................................................................................. 2.60 3.20 3.80 4.50 5.10 5.70 6.40 7.00 8.30 13051
13052 Fix only pipe to floor, wall or soffits .............................................. 10.60 12.40 13.20 13.20 15.00 17.70 20.30 21.20 23.00 13052
13/22
13 PLUMBING AND DRAINAGE 13
Item Item
COPPER PIPES AND FITTINGS FOR WATER SUPPLY SYSTEM (CONT'D)
Copper pipes and fittings to BS EN 1057: 2006 with
amendment A1: 2010 insulation polyethylene sheath, Outside diameter (mm)
for fresh water supply system : - (Cont'd) 15 22 28 35 42 54 67 76 108
A B C D E F G H I
Each $ $ $ $ $ $ $ $ $
13053 Repair and make good one existing joint for "compression type"
joint fittings including loosening nut and compression
ring, cleaning tube end and re-tightening ....................................... 7.50 8.40 9.30 10.10 11.00 12.80 15.10 16.90 21.30 13053
13054 Repair and make good one existing joint for "capillary
type" joint fittings including heating, re-tinning tub end
and re-soldering as necessary ......................................................... 25.70 28.40 32.80 36.30 40.70 47.80 54.90 62.80 80.50 13054
13055 Seal off existing pipe fixed in position including providing
and jointing on "compression type" stop end ................................. 28.80 34.10 43.80 87.90 118.90 135.60 149.80 160.40 189.50 13055
13056 Ditto but "capillary type" stop end ................................................. 30.60 35.00 41.20 72.10 79.10 89.70 123.30 145.30 189.50 13056
Pipe diameter (mm)
15 22 28 35 42 54
A B C D E F
Per linear metre $ $ $ $ $ $
13057 Add to Item 13033 for approved white polyethylene sleeve covered copper
pipe in lieu of plain copper pipe including all cutting and fitting at joints,
tees, bends and other fittings or alternatively covering such fittings with
insulation quilt or insulation rope to the thickness required ............................................................... 15.00 17.70 19.40 30.00 30.90 38.00 13057
STAINLESS STEEL PIPES AND FITTINGS FOR WATER SUPPLY SYSTEM
Stainless steel pipes and fittings to BS EN 10312: 2002 with amendment A1: Pipe diameter (mm)
2005, for fresh water supply system : - 15 18 22 28 35 42
A B C D E F
Per linear metre $ $ $ $ $ $
13058 Pipe fixed to floor, wall or soffits ........................................................................................................ 94.70 109.10 136.20 172.00 229.20 263.30 13058
Per linear metre
13059 Take down and clear away pipe fixed to floor wall or soffits ............................................................. 1.90 2.60 3.20 3.80 4.50 5.10 13059
13060 Take down and set aside for re-use pipe fixed to floor, wall or soffits................................................ 3.20 3.80 4.50 5.10 5.70 6.40 13060
13061 Fix only pipe to floor, wall or soffits .................................................................................................... 13.20 15.00 16.80 18.50 20.30 23.00 13061
Each
13062 Repair and make good existing joint including cleaning ends............................................................. 21.70 24.40 26.10 28.80 30.60 34.10 13062
13063 Seal off existing pipe fixed in position including
threading end and providing and jointing on cap or plug .................................................................... 50.00 52.60 57.00 72.10 87.10 101.20 13063
13/23
13 PLUMBING AND DRAINAGE 13
Item Item
STAINLESS STEEL PIPES AND FITTINGS FOR WATER SUPPLY SYSTEM (CONT'D)
Pipe diameter (mm)
Stainless steel pipes and fittings to BS EN 10217-7: 2005 for fresh water supply system : - 54 76
A B
Per linear metre $ $
13064 Pipe laid in trench......................................................................................................................................................................................................... 336.30 571.20 13064
13065 Pipe fixed to floor, wall or soffits ................................................................................................................................................................................ 347.20 589.40 13065
Each
13066 Extra over for cap end or plug....................................................................................................................................................................................... 69.00 71.80 13066
13067 Ditto for bend or elbow ................................................................................................................................................................................................ 221.70 305.50 13067
13068 Ditto for three-way elbow or tee .................................................................................................................................................................................. 248.80 350.20 13068
13069 Ditto for cross ............................................................................................................................................................................................................... 317.10 638.00 13069
13070 Ditto for reducer ........................................................................................................................................................................................................... 202.20 298.70 13070
13071 Ditto for connector to existing pipework...................................................................................................................................................................... 113.10 159.20 13071
13072 Ditto flanged tank connector or double nut tank connector to existing water tank cistern and the like..................................................................... 545.00 701.00 13072
Per linear metre
13073 Take up and clear away pipe laid in trench (trench excavation measured separately) ............................................................................................... 5.10 5.70 13073
13074 Take up and set aside for re-use pipe laid in trench (ditto) ......................................................................................................................................... 6.40 7.00 13074
13075 Take down and clear away pipe fixed to floor wall or soffits ..................................................................................................................................... 5.70 6.40 13075
13076 Take down and set aside for re-use pipe fixed to floor, wall or soffits........................................................................................................................ 7.00 7.70 13076
13077 Lay only pipe in trench.................................................................................................................................................................................................. 22.10 24.70 13077
13078 Fix only pipe to floor, wall or soffits ........................................................................................................................................................................... 23.80 26.50 13078
Each
13079 Repair and make good existing joint including cleaning ends..................................................................................................................................... 36.70 39.40 13079
13080 Seal off existing pipe fixed in position including threading end and
providing and jointing on cap or plug .......................................................................................................................................................................... 116.20 131.20 13080
13/24
13 PLUMBING AND DRAINAGE 13
Item Item
UPVC PIPES AND FITTINGS FOR WATER SUPPLY SYSTEM
UPVC Pressure pipes and fittings to BS 3505: 1986 Class D Pipe diameter (mm)
for fresh and flushing water supply system : - 15 20 25 32 40 50 65
A B C D E F G
Per linear metre $ $ $ $ $ $ $
13081 Pipe laid in trench................................................................................................................ 40.80 49.90 71.60 85.30 91.50 107.00 130.70 13081
13082 Pipe fixed to floor, wall or soffits........................................................................................ 42.30 53.50 75.30 91.20 98.80 117.90 145.20 13082
Each
13083 Extra over pipe for cap end................................................................................................. - - - - - - 23.90 13083
13084 Ditto for bend or elbow....................................................................................................... - - - - - - 150.90 13084
13085 Ditto for tee.......................................................................................................................... - - - - - - 209.20 13085
13086 Ditto for connector to existing pipework............................................................................ - - - - - - 95.10 13086
13087 Ditto flanged tank connector or double nut tank connector to
existing water tank cistern and the like............................................................................... - - - - - - 492.90 13087
Per linear metre
13088 Take up and clear away pipe laid in trench (trench excavation
measured separately)........................................................................................................... 1.30 1.90 2.60 3.20 3.80 4.50 5.10 13088
13089 Take up and set aside for re-use pipe laid in trench (ditto)............................................... 2.60 3.20 3.80 4.50 5.10 5.70 6.40 13089
13090 Take down and clear away pipe fixed to floor, wall or soffits........................................... 1.90 2.60 3.20 3.80 4.50 5.10 5.70 13090
13091 Take down and set aside for re-use pipe fixed to floor, wall or soffits.............................. 3.20 3.80 4.50 5.10 5.70 6.40 7.00 13091
13092 Lay only pipe in trench........................................................................................................ 4.40 5.30 6.20 7.10 8.00 8.80 9.70 13092
13093 Fix only pipe to floor, wall or soffits................................................................................... 9.70 10.60 12.40 13.20 14.10 18.50 22.10 13093
Each
13094 Seal off existing pipe fixed in position including threading end and
providing and jointing on cap or plug................................................................................. 18.70 24.00 31.90 39.00 50.40 55.70 67.30 13094
13/25
13 PLUMBING AND DRAINAGE 13
Item Item
UPVC PIPES AND FITTINGS FOR WATER SUPPLY SYSTEM (CONT'D)
UPVC Pressure pipes and fittings to BS 3505: 1986 Class D Pipe diameter (mm)
for fresh and flushing water supply system : - (Cont'd) 80 100 150 200 250 300
A B C D E F
Per linear metre $ $ $ $ $ $
13095 Pipe laid in trench.................................................................................................................................. 154.00 184.90 225.00 414.20 474.40 597.80 13095
13096 Pipe fixed to floor, wall or soffits......................................................................................................... 172.20 206.70 254.10 446.90 510.80 637.80 13096
Each
13097 Extra over pipe for cap end................................................................................................................... 73.30 121.20 283.20 421.90 546.50 713.50 13097
13098 Ditto for bend or elbow......................................................................................................................... 155.10 218.90 405.80 604.60 783.10 1,022.50 13098
13099 Ditto for tee............................................................................................................................................ 211.60 321.80 474.30 692.50 853.80 1,053.70 13099
13100 Ditto for connector to existing pipework.............................................................................................. 96.20 146.30 215.60 314.80 388.10 479.00 13100
13101 Ditto flanged tank connector or double nut tank
connector to existing water tank cistern and the like............................................................................ 534.00 844.40 1,061.30 1,415.00 1,768.80 2,122.50 13101
Per linear metre
13102 Take up and clear away pipe laid in trench
(trench excavation measured separately).............................................................................................. 5.70 6.40 7.70 8.90 10.20 11.50 13102
13103 Take up and set aside for re-use pipe laid in trench (ditto)................................................................. 7.00 7.70 10.20 11.50 12.80 14.70 13103
13104 Take down and clear away pipe fixed to floor, wall or soffits............................................................. 6.40 7.00 8.30 9.60 10.90 12.10 13104
13105 Take down and set aside for re-use pipe fixed to floor, wall or soffits................................................ 7.70 8.30 10.90 12.10 13.40 15.30 13105
13106 Lay only pipe in trench.......................................................................................................................... 9.70 10.60 12.40 15.00 15.90 16.80 13106
13107 Fix only pipe to floor, wall or soffits .................................................................................................... 23.80 27.40 30.90 34.40 38.00 41.50 13107
Each
13108 Seal off existing pipe fixed in position including threading end and
providing and jointing on cap or plug................................................................................................... 117.70 258.90 584.90 721.00 945.40 1,085.10 13108
13/26
13 PLUMBING AND DRAINAGE 13
Item Item
POLYETHYLENE (PE) PIPES AND FITTINGS FOR WATER SUPPLY SYSTEM
PE Pressure pipes and fittings to BS 6572 or
BS-EN-12201-3-2003 with nominal pressure rating Pipe diameter (mm)
PN16, SDR 11, for fresh water supply system : - 25 32 50 63 90 125 180 250 315
A B C D E F G H I
Per linear metre $ $ $ $ $ $ $ $ $
13109 Pipe laid in trench............................................................................ 10.90 15.40 29.60 43.80 67.50 120.20 237.60 446.30 700.20 13109
Each
13110 Extra over pipe for cap end.............................................................. - - - 75.40 106.60 200.70 466.10 934.50 1,491.20 13110
13111 Ditto for bend or elbow................................................................... - - - 174.30 234.60 369.40 722.60 1,277.10 1,895.50 13111
13112 Ditto for tee...................................................................................... - - - 230.80 380.20 574.20 1,184.10 1,808.30 2,939.60 13112
13113 Ditto for connector to existing pipework........................................ - - - 104.90 172.80 261.00 538.20 821.90 1,336.20 13113
13114 Ditto flanged tank connector or double nut tank
connector to existing water tank cistern and the like...................... - - - 453.10 609.90 960.40 1,300.70 1,915.70 2,274.60 13114
Per linear metre
13115 Take up and clear away pipe laid in trench
(trench excavation measured separately)........................................ 3.80 4.50 5.10 5.70 6.40 8.30 10.20 12.80 16.60 13115
13116 Take up and set aside for re-use pipe laid
in trench (ditto)................................................................................ 5.10 5.70 6.40 7.00 7.70 9.60 11.50 14.00 17.90 13116
13117 Lay only pipe in trench.................................................................... 5.30 6.20 7.10 8.00 10.60 13.20 15.90 18.50 21.20 13117
PE Pressure pipes and fittings to BS 6730 or
BS-EN-12201-3-2003 with nominal pressure
rating PN20, SDR 9, for fresh water supply system : -
Per linear metre
13118 Pipe fixed to floor, wall or soffits.................................................... 16.40 20.40 41.70 62.90 119.90 223.50 470.40 963.60 1,497.90 13118
Each
13119 Extra over pipe for cap end.............................................................. - - - 82.40 114.60 206.30 473.70 944.60 1,517.40 13119
13120 Ditto for bend or elbow................................................................... - - - 185.60 259.30 394.40 745.20 1,299.60 1,912.90 13120
13121 Ditto for tee...................................................................................... - - - 264.20 420.90 618.30 1,222.60 1,871.30 2,992.30 13121
13122 Ditto for connector to existing pipework........................................ - - - 120.10 191.30 281.10 555.70 850.60 1,360.10 13122
13123 Ditto flanged tank connector or double nut tank
connector to existing water tank cistern and the like...................... - - - 482.60 674.30 1,025.40 1,341.40 1,949.40 2,295.50 13123
13/27
13 PLUMBING AND DRAINAGE 13
Item Item
POLYETHYLENE (PE) PIPES AND FITTINGS FOR WATER SUPPLY SYSTEM (CONT'D)
PE Pressure pipes and fittings to BS 6730 or
BS-EN-12201-3-2003 with nominal pressure rating PN20, Pipe diameter (mm)
SDR 9, for fresh water supply system : - (Cont'd) 25 32 50 63 90 125 180 250 315
A B C D E F G H I
Per linear metre $ $ $ $ $ $ $ $ $
13124 Take down and clear away pipe fixed to
floor, wall or soffits......................................................................... 4.50 5.10 5.70 6.40 7.00 8.90 10.90 13.40 17.20 13124
13125 Take down and set aside for re-use pipe
fixed to floor, wall or soffits............................................................ 5.70 6.40 7.00 7.70 8.30 10.20 12.10 14.70 18.50 13125
13126 Fix only pipe to floor, wall or soffits............................................... 8.80 9.70 14.10 15.00 18.50 21.20 26.50 31.80 37.10 13126
Each
13127 Seal off existing pipe fixed in position including
threading end and providing and jointing on cap
or plug.............................................................................................. 38.20 45.30 59.50 85.20 141.80 378.70 632.70 989.50 1,173.40 13127
THERMAL INSULATION TO PIPES
Take Take
(Note: The following Items 13128 to 13131 inclusive do not apply to factory applied thermal Supply down down Fix
insulation to pre-insulated pipework.) and and and set only
fix clear aside for
away re-use
A B C D
Per linear metre $ $ $ $
13128 Thermal insulation to pipework n.e. 15 mm diameter.............................................................................................................. 57.40 14.00 15.30 32.70 13128
13129 Ditto but 15 - 30 mm diameter ................................................................................................................................................. 63.40 16.00 17.90 39.70 13129
13130 Ditto but 30 - 40 mm diameter ................................................................................................................................................ 105.70 17.90 18.50 45.90 13130
13131 Ditto but 40 - 55 mm diameter ................................................................................................................................................ 129.90 21.10 22.30 53.00 13131
13/28
13 PLUMBING AND DRAINAGE 13
Item Item
CAST IRON RAINWATER GUTTERS AND FITTINGS
Half round section Ogee
Cast iron gutter and fittings to BS 416-1: 1990, internally and externally coated : - section
Internal Internal
diameter diameter
(mm) (mm)
75 100 150 100
A B C D
Per linear metre $ $ $ $
13132 Gutter fixed on brackets at 1.00 m (maximum) centres .......................................................................................................... 116.90 156.40 241.10 165.20 13132
Each
13133 Extra over gutter for stop end ................................................................................................................................................... 42.40 54.00 65.70 54.00 13133
13134 Ditto internal or external angle ................................................................................................................................................ 54.00 63.10 106.50 77.40 13134
13135 Ditto nozzle outlet .................................................................................................................................................................... 77.40 96.40 160.60 124.20 13135
13136 Ditto combined stop end nozzle outlet .................................................................................................................................... 92.00 122.60 198.50 153.30 13136
Per linear metre
13137 Take down and clear away gutter complete with all fittings and brackets ............................................................................. 8.30 11.50 14.00 12.10 13137
13138 Take down and set aside for re-use ditto ................................................................................................................................. 8.90 12.10 14.70 12.80 13138
13139 Fix only gutter complete including providing brackets at 1.00 m (maximum) centres ......................................................... 51.40 61.80 88.30 70.60 13139
Each
13140 Repair and make good existing joint including cleaning ends ................................................................................................ 23.20 26.70 40.80 33.80 13140
13/29
13 PLUMBING AND DRAINAGE 13
Item Item
CAST IRON PIPES AND FITTINGS FOR SURFACE AND FOUL WATER DRAINAGE
Pipe diameter (mm)
Cast iron pipes and fittings to BS 416-1: 1990, internally and externally coated, for surface water drainage : - 100 150
A B
Per linear metre $ $
13141 Pipe fixed to floor, wall or soffits................................................................................................................................................................................. 226.70 353.60 13141
Each
13142 Extra over pipe for shoe ............................................................................................................................................................................................... 292.20 411.70 13142
13143 Ditto for bend ............................................................................................................................................................................................................... 193.50 258.40 13143
13144 Ditto for single junction ............................................................................................................................................................................................... 149.30 406.70 13144
13145 Ditto for double junction .............................................................................................................................................................................................. 273.80 516.20 13145
13146 Ditto for connector to existing pipework...................................................................................................................................................................... 67.90 184.80 13146
13147 Add to either of Items 13143 to 13145 inclusive if fitted with bolted access door .................................................................................................... 72.70 80.70 13147
13148 Swan-neck of any projection ........................................................................................................................................................................................ 259.40 425.00 13148
13149 Roof outlet with square or circular, flat or domed grating .......................................................................................................................................... 466.80 602.10 13149
13150 Rainwater head, flat or angular .................................................................................................................................................................................... 131.70 148.90 13150
Per linear metre
13151 Take down and clear away pipe fixed to floor, wall or soffits .................................................................................................................................... 7.70 10.20 13151
13152 Take down and set aside for re-use pipe fixed to floor, wall or soffits ....................................................................................................................... 9.60 12.80 13152
13153 Fix only pipe to floor, wall or soffits ........................................................................................................................................................................... 23.00 35.30 13153
Each
13154 Repair and make good existing joint including cleaning ends .................................................................................................................................... 51.40 69.10 13154
13/30
13 PLUMBING AND DRAINAGE 13
Item Item
CAST IRON PIPES AND FITTINGS FOR SURFACE AND FOUL WATER DRAINAGE (CONT'D)
Pipe diameter (mm)
50 65 75 90 150
Cast iron pipes and fittings to BS 416-1: 1990, internally and externally coated, for foul water drainage : - or 80 or 100
A B C D E
Per linear metre $ $ $ $ $
13155 Pipe fixed to floor, wall or soffits........................................................................................................................... 113.30 147.30 170.00 226.70 353.60 13155
Each
13156 Extra over pipe for loose socket ............................................................................................................................. 51.50 57.70 65.10 82.30 120.00 13156
13157 Ditto for large socket for and including joint to clayware pipe ............................................................................. - - - 151.60 209.40 13157
13158 Ditto for swan-neck of any projection .................................................................................................................... - 149.70 202.00 234.00 421.00 13158
13159 Ditto for plug to socket end .................................................................................................................................... - 127.00 169.70 205.70 291.10 13159
13160 Ditto for cap to spigot end ...................................................................................................................................... - 166.10 193.20 215.00 308.10 13160
13161 Ditto for bend ......................................................................................................................................................... - 127.90 147.80 193.50 258.40 13161
13162 Ditto for single junction ......................................................................................................................................... - 136.90 150.10 174.90 406.70 13162
13163 Ditto for double junction ........................................................................................................................................ - 208.50 233.70 335.00 600.90 13163
13164 Ditto for connector to existing pipework................................................................................................................ - 62.20 68.30 79.50 184.80 13164
13165 Add to either of Items 13161 to 13163 inclusive if fitted with bolted access door .............................................. - 101.30 118.30 121.90 135.50 13165
Per linear metre
13166 Take down and clear away pipe fixed to floor, wall or soffits .............................................................................. 4.50 5.10 6.40 8.30 9.60 13166
13167 Take down and set aside for re-use pipe fixed to floor, wall or soffits ................................................................. 6.40 7.00 8.30 9.60 10.90 13167
13168 Fix only pipe to floor, wall or soffits ...................................................................................................................... 15.00 19.40 21.20 24.70 30.90 13168
Each
13169 Cut or burn out existing joint, clean socket and spigot ends, repair and
make good existing joint ........................................................................................................................................ 61.80 70.60 79.50 97.10 123.60 13169
13/31
13 PLUMBING AND DRAINAGE 13
Item Item
CAST IRON PIPES AND FITTINGS FOR SURFACE AND FOUL WATER DRAINAGE (CONT'D)
Pipe
Cast iron pipes and fittings to BS 437: 2008, internally and externally coated for foul water drainage : - diameter
(mm)
200
or 225
A
Per linear metre $
13170 Pipe fixed to floor, wall or soffits................................................................................................................................................................................................... 1,052.00 13170
Each
13171 Extra over pipe for loose socket ..................................................................................................................................................................................................... 384.50 13171
13172 Ditto for large socket for and including joint to clayware pipe ..................................................................................................................................................... 866.60 13172
13173 Ditto for swan-neck of any projection ........................................................................................................................................................................................... 1,790.00 13173
13174 Ditto for plug to socket end ............................................................................................................................................................................................................ 1,192.80 13174
13175 Ditto for cap to spigot end .............................................................................................................................................................................................................. 1,426.40 13175
13176 Ditto for bend ................................................................................................................................................................................................................................. 1,174.30 13176
13177 Ditto for single junction ................................................................................................................................................................................................................. 1,430.70 13177
13178 Ditto for double junction ................................................................................................................................................................................................................ 2,540.70 13178
13179 Ditto for connector to existing pipework........................................................................................................................................................................................ 469.70 13179
13180 Add to either of Items 13176 to 13178 inclusive if fitted with bolted access door ...................................................................................................................... 470.00 13180
Per linear metre
13181 Take down and clear away pipe fixed to floor, wall or soffits ...................................................................................................................................................... 12.80 13181
13182 Take down and set aside for re-use pipe fixed to floor, wall or soffits ......................................................................................................................................... 14.00 13182
13183 Fix only pipe to floor, wall or soffits ............................................................................................................................................................................................. 42.40 13183
Each
13184 Cut or burn out existing joint, clean socket and spigot ends, repair and make good existing joint ............................................................................................. 158.90 13184
13/32
13 PLUMBING AND DRAINAGE 13
Item Item
CAST IRON PIPES AND FITTINGS FOR SURFACE AND FOUL WATER DRAINAGE (CONT'D)
Pipe diameter (mm)
Grey iron pipes and fittings to BS 4622: 1970, internally and externally coated, for foul water drainage : - 200 250
or 225
A B
Per linear metre $ $
13185 Pipe fixed to floor, wall or soffits................................................................................................................................................................................. 1,208.10 1,330.90 13185
Each
13186 Extra over pipe for loose socket ................................................................................................................................................................................... 384.50 477.40 13186
13187 Ditto for large socket for and including joint to
clayware pipe ................................................................................................................................................................................................................ 866.60 1,043.70 13187
13188 Ditto for swan-neck of any projection ......................................................................................................................................................................... 1,790.00 2,342.80 13188
13189 Ditto for plug to socket end .......................................................................................................................................................................................... 1,192.80 1,478.30 13189
13190 Ditto for cap to spigot end ............................................................................................................................................................................................ 1,426.40 1,640.50 13190
13191 Ditto for bend ............................................................................................................................................................................................................... 1,187.30 1,448.50 13191
13192 Ditto for single junction ............................................................................................................................................................................................... 1,430.70 2,246.60 13192
13193 Ditto for double junction .............................................................................................................................................................................................. 2,540.70 3,223.50 13193
13194 Ditto for connector to existing pipework...................................................................................................................................................................... 565.40 689.70 13194
13195 Add to either of Items 13191 to 13193 inclusive if fitted with bolted access door .................................................................................................... 470.00 495.10 13195
Per linear metre
13196 Take down and clear away pipe fixed to floor, wall or soffits .................................................................................................................................... 12.80 15.30 13196
13197 Take down and set aside for re-use pipe fixed to floor, wall or soffits ....................................................................................................................... 14.00 16.60 13197
13198 Fix only pipe to floor, wall or soffits ........................................................................................................................................................................... 42.40 49.50 13198
Each
13199 Cut or burn out existing joint, clean socket and spigot ends, repair and make good existing joint ........................................................................... 158.90 185.40 13199
13/33
13 PLUMBING AND DRAINAGE 13
Item Item
CAST IRON PIPES AND FITTINGS FOR SURFACE AND FOUL WATER DRAINAGE (CONT'D)
Cast iron socketless pipes and fittings to BS EN 877:1999
with amendment for surface A1: 2006, epoxy coated internally, Pipe diameter (mm)
anti-corrosive coated externally, for surface or foul water 40 50 70 100 150 200 250 300
drainage : - or 75 or 125
A B C D E F G H
Per linear metre $ $ $ $ $ $ $ $
13200 Pipe fixed to floor, wall or soffits...................................................................... 302.10 362.50 453.10 543.70 713.70 1,017.50 1,616.90 1,943.30 13200
Each
13201 Extra over pipe for cap end or plug................................................................... - - 212.20 266.00 350.90 493.50 565.30 600.40 13201
13202 Ditto for bend or elbow..................................................................................... - - 271.40 314.70 486.60 970.40 1,728.00 2,226.80 13202
13203 Ditto for three-way elbow or tee........................................................................ - - 297.60 421.30 649.50 1,286.70 2,360.60 3,207.00 13203
13204 Ditto for access door.......................................................................................... - - 541.60 787.00 1,608.70 1,764.80 1,924.50 2,352.50 13204
13205 Ditto for reducer................................................................................................ - - 211.30 275.40 347.50 430.90 737.00 909.50 13205
13206 Ditto for connector to existing pipework.......................................................... - - 135.30 157.40 243.30 485.20 864.00 1,113.40 13206
Per linear metre
13207 Take down and clear away pipe fixed to floor, wall or soffits.......................... 3.80 4.50 5.70 6.40 8.30 9.60 10.90 12.80 13207
13208 Take down and set aside for re-use pipe fixed to floor, wall or
soffits.................................................................................................................. 5.70 6.40 7.70 8.90 10.90 11.50 12.80 14.00 13208
13209 Fix only pipe to floor, wall or soffits................................................................. 11.50 12.40 13.20 15.90 17.70 18.50 20.30 25.60 13209
Each
13210 Repair and make good existing joint including cleaning ends ........................ 20.80 27.90 35.00 36.70 40.30 44.40 51.40 66.40 13210
13211 Seal off existing pipe laid or fixed in position including threading
end and providing and jointing on cap or plug ................................................ 47.80 91.90 136.10 180.20 228.00 272.20 316.30 360.50 13211
13/34
13 PLUMBING AND DRAINAGE 13
Item Item
GALVANIZED IRON PIPES AND FITTINGS FOR FOUL WATER DRAINAGE
Galvanized iron pipes and fittings to BS EN 10255 : 2004 Pipe diameter (mm)
medium grade and hot dip zinc coated for foul water drainage : - 90 114 140 165
A B C D
Per linear metre $ $ $ $
13212 Pipe fixed to floor, wall or soffits............................................................................................................................................. 348.60 441.60 499.60 588.80 13212
Each
13213 Extra over pipe for cap end or plug........................................................................................................................................... 63.30 114.00 128.70 137.80 13213
13214 Ditto for bend or elbow............................................................................................................................................................. 126.30 158.20 292.40 344.60 13214
13215 Ditto for three-way elbow or tee............................................................................................................................................... 169.90 217.10 399.30 470.60 13215
13216 Ditto for access door.................................................................................................................................................................. 354.80 609.80 1,030.80 1,214.90 13216
13217 Ditto for reducer........................................................................................................................................................................ 115.80 128.80 173.40 204.40 13217
13218 Ditto for connector to existing pipework.................................................................................................................................. 77.30 98.70 181.50 213.90 13218
Per linear metre
13219 Take down and clear away pipe fixed to floor, wall or soffits................................................................................................. 5.70 7.00 7.70 8.90 13219
13220 Take down and set aside for re-use pipe fixed to floor, wall or soffits.................................................................................... 8.30 9.60 10.20 11.50 13220
13221 Fix only pipe to floor, wall or soffits......................................................................................................................................... 15.00 16.80 17.70 18.50 13221
Each
13222 Repair and make good existing joint including cleaning ends ................................................................................................ 35.80 37.60 39.40 41.10 13222
13223 Seal off existing pipe laid or fixed in position including threading end and providing
and jointing on cap or plug ...................................................................................................................................................... 162.60 201.50 219.20 245.70 13223
13/35
13 PLUMBING AND DRAINAGE 13
Item Item
UPVC RAINWATER GUTTERS AND FITTINGS
Internal
UPVC Pipes and fittings to BS 5255: 1989 : - diameter
(mm)
80
A
Per linear metre $
13224 Half round rainwater gutter fixed on brackets at 1.00 m (maximum) centres .............................................................................................................................. 91.90 13224
Each
13225 Extra over half round gutter for stop end ....................................................................................................................................................................................... 41.00 13225
13226 Ditto for internal or external angle ................................................................................................................................................................................................. 148.30 13226
13227 Nozzle outlet .................................................................................................................................................................................................................................. 60.90 13227
13228 Combined stop end and nozzle outlet ............................................................................................................................................................................................ 74.10 13228
Per linear metre
13229 Take down and clear away gutter .................................................................................................................................................................................................. 7.00 13229
13230 Take down and set aside for re-use gutter ..................................................................................................................................................................................... 7.70 13230
13231 Fix only gutter including providing brackets at 1.00 m (maximum) centres ................................................................................................................................ 39.70 13231
UPVC Pipes and fittings to BS 4514 : 2001 : - Internal
diameter (mm)
100 150
A B
Per linear metre $ $
13232 Half round rainwater gutter fixed on brackets at 1.00 m (maximum) centres ............................................................................................................ 113.70 206.50 13232
Each
13233 Extra over half round gutter for stop end ..................................................................................................................................................................... 50.70 84.50 13233
13234 Ditto for internal or external angle ............................................................................................................................................................................... 185.40 353.90 13234
13235 Nozzle outlet ................................................................................................................................................................................................................. 76.10 118.30 13235
13236 Combined stop end and nozzle outlet .......................................................................................................................................................................... 92.70 134.80 13236
Per linear metre
13237 Take down and clear away gutter ................................................................................................................................................................................ 8.30 10.90 13237
13238 Take down and set aside for re-use gutter ................................................................................................................................................................... 9.60 12.10 13238
13239 Fix only gutter including providing brackets at 1.00 m (maximum) centres .............................................................................................................. 47.70 91.00 13239
13/36
13 PLUMBING AND DRAINAGE 13
Item Item
UPVC PIPES AND FITTINGS FOR SURFACE AND FOUL WATER DRAINAGE
Pipe diameter (mm)
UPVC Non-pressure pipes and fittings to BS 5255 : 1989 for foul water drainage : - 32 43 56
A B C
Per linear metre $ $ $
13240 Pipe fixed to floor, wall or soffits .............................................................................................................................................................. 40.70 62.70 72.10 13240
Each
13241 Extra over pipe for cap end ........................................................................................................................................................................ - - 43.50 13241
13242 Ditto for bend or elbow .............................................................................................................................................................................. - - 35.50 13242
13243 Ditto for branch .......................................................................................................................................................................................... - - 54.60 13243
13244 Ditto for double branch .............................................................................................................................................................................. - - 68.00 13244
13245 Ditto for connector to existing pipework.................................................................................................................................................... - - 24.80 13245
13246 Add to either of Items 13242 to 13244 inclusive for screwed access ....................................................................................................... - - 155.30 13246
13247 Tapered socket with cap nut and joint to steel tubing or brass fittings ..................................................................................................... - - 69.60 13247
13248 Flat roof outlet with raised grating ............................................................................................................................................................. - - 97.10 13248
Per linear metre
13249 Take down and clear away pipe fixed to floor, wall or soffits .................................................................................................................. 2.60 3.20 3.80 13249
13250 Take down and set aside for re-use pipe fixed to floor, wall or soffits ..................................................................................................... 3.20 3.80 4.50 13250
13251 Fix only pipe to floor, wall or soffits .......................................................................................................................................................... 7.10 8.00 8.80 13251
Each
13252 Seal off existing pipe fixed in position including threading
end and providing and jointing on cap or plug .......................................................................................................................................... 33.80 44.40 49.70 13252
13/37
13 PLUMBING AND DRAINAGE 13
Item Item
UPVC PIPES AND FITTINGS FOR SURFACE AND FOUL WATER DRAINAGE (CONT'D)
UPVC Non-pressure pipes and fittings to BS 4514: 2001 for foul water drainage : - Pipe diameter (mm)
65 80 100 150
A B C D
Per linear metre $ $ $ $
13253 Pipe fixed to floor, wall or soffits ............................................................................................................................................ 79.10 86.20 94.10 167.60 13253
Each
13254 Extra over pipe for cap end ...................................................................................................................................................... 65.90 88.30 137.90 287.40 13254
13255 Ditto for bend or elbow ............................................................................................................................................................ 46.20 55.10 71.10 106.10 13255
13256 Ditto for branch ........................................................................................................................................................................ 56.80 69.50 81.90 136.90 13256
13257 Ditto for double branch ............................................................................................................................................................ 162.70 257.50 332.90 841.60 13257
13258 Ditto for connector to existing pipework.................................................................................................................................. 25.80 31.60 37.20 62.20 13258
13259 Add to either of Items 13255 to 13257 inclusive for screwed access ..................................................................................... 161.10 166.90 174.80 242.30 13259
13260 Tapered socket with cap nut and joint to steel tubing or brass fittings ................................................................................... 90.50 111.40 139.20 208.90 13260
13261 Flat roof outlet with raised grating ........................................................................................................................................... 115.50 142.10 194.20 334.40 13261
Per linear metre
13262 Take down and clear away pipe fixed to floor, wall or soffits ................................................................................................ 4.50 5.10 6.40 9.60 13262
13263 Take down and set aside for re-use pipe fixed to floor, wall or soffits ................................................................................... 5.10 5.70 7.00 10.90 13263
13264 Fix only pipe to floor, wall or soffits ........................................................................................................................................ 9.70 11.50 12.40 14.10 13264
Each
13265 Seal off existing pipe fixed in position including threading end and providing and jointing on cap or plug ........................ 69.10 88.50 132.70 243.00 13265
13/38
13 PLUMBING AND DRAINAGE 13
Item Item
VULCATHENE MECHANICAL WASTE PIPES AND FITTINGS
FOR ABOVE GROUND DRAINAGE Pipe diameter (mm)
38 51
A B
Per linear metre $ $
13266 Pipe fixed to floor, wall or ceiling with and including brackets.................................................................................................................................. 141.00 211.50 13266
Each
13267 Extra over pipe for cap end........................................................................................................................................................................................... - 70.80 13267
13268 Ditto for bend or elbow................................................................................................................................................................................................. - 152.60 13268
13269 Ditto for branch............................................................................................................................................................................................................. - 174.50 13269
13270 Ditto for reducer............................................................................................................................................................................................................ - 138.10 13270
13271 Ditto for connector to existing pipework...................................................................................................................................................................... - 79.30 13271
PRECAST CONCRETE PIPES FOR BELOW GROUND DRAINAGE
Precast concrete pipes and fittings to BS 5911-1:2002 with amendment A2: 2010 or BS
EN 1916: 2002, for below ground drainage :- Pipe bore (mm)
150 225 300 375 450
A B C D E
Per linear metre $ $ $ $ $
13272 Pipe, unreinforced, laid in trench............................................................................................................................ 421.20 550.60 655.20 853.80 1,105.10 13272
13273 Ditto, reinforced, laid in trench............................................................................................................................... - - - - 1,160.30 13273
VITRIFIED CLAY PIPES AND FITTINGS FOR BELOW GROUND DRAINAGE
Vitrified clay pipes and fittings to BS 65:1991, chemical resistant, for below ground drainage :- Pipe bore (mm)
100 150 225 300
A B C D
Per linear metre $ $ $ $
13274 Pipe laid in trench...................................................................................................................................................................... 340.10 451.10 617.60 943.50 13274
Each
13275 Extra over pipe for taper pipe.................................................................................................................................................... - 68.40 177.60 - 13275
13276 Ditto for bend............................................................................................................................................................................ 95.20 154.70 360.90 - 13276
13277 Ditto for single junction............................................................................................................................................................ 150.70 222.10 404.50 622.60 13277
13/39
13 PLUMBING AND DRAINAGE 13
Item Item
DUCTILE IRON PIPES AND FITTINGS FOR BELOW GROUND DRAINAGE
Ductile iron pipes and fittings to BS EN 598: 2007 with amendment A1: 2009 Pipe bore (mm)
with cement lining internally and zinc coating externally, for below ground drainage :- 80 100 150 200 250 300
A B C D E F
Per linear metre $ $ $ $ $ $
13278 Pipe laid in trench.................................................................................................................................. 490.00 519.40 643.80 771.80 945.30 1,116.90 13278
13279 Drop pipe............................................................................................................................................... 741.70 777.70 924.20 1,074.90 1,329.00 1,454.70 13279
Each
13280 Extra over pipe for cover plate for end................................................................................................. 77.13 123.70 192.80 269.20 352.90 499.20 13280
13281 Ditto for socket end (for repair work only)........................................................................................... 154.60 189.80 293.40 327.00 488.30 639.10 13281
13282 Ditto for spigot end (for repair work only)............................................................................................ 164.90 197.30 310.30 342.90 514.80 702.50 13282
13283 Ditto for connector with screwed end to existing pipework................................................................. 183.00 221.00 340.70 378.30 568.90 757.40 13283
13284 Ditto for bend......................................................................................................................................... 177.40 270.00 461.30 647.90 1,176.00 1,505.50 13284
13285 Ditto for single junction........................................................................................................................ 249.40 282.80 496.60 714.80 1,249.90 1,507.10 13285
13286 Ditto for double junction....................................................................................................................... 250.60 381.70 645.90 735.90 1,287.70 1,908.20 13286
13287 Add to either of Items 13284 to 13286 inclusive if fitted with bolted
access door............................................................................................................................................. 22.70 41.10 70.90 104.40 186.00 267.60 13287
Per linear metre
13288 Take up and clear away pipe laid in trench complete with all fittings (trench
excavation measured separately)........................................................................................................... 8.90 9.60 13.40 16.00 21.10 26.80 13288
13289 Take up and set aside for re-use ditto................................................................................................... 11.50 13.40 17.20 21.70 27.40 33.80 13289
13290 Break up and clear away concrete beds and surrounds if any including drain
pipes and fittings (trench excavation measured separately)................................................................. 26.80 29.30 37.00 52.90 63.10 73.30 13290
13291 Lay only pipe in trench.......................................................................................................................... 35.30 37.10 41.50 48.60 58.30 70.60 13291
13292 Fix only drop pipe.................................................................................................................................. 115.00 120.20 129.70 139.10 148.50 158.90 13292
Each
13293 Remove gasket to existing joint and clear away and re-joint with new gasket.................................... 49.10 57.50 68.00 73.20 78.40 84.70 13293
13/40
13 PLUMBING AND DRAINAGE 13
Item Item
CAST IRON PIPES AND FITTINGS FOR BELOW GROUND DRAINAGE
Pipe
Cast iron pipes and fittings to BS 437: 2008, internally and externally coated, for below ground drainage :- diameter
(mm)
200
or 225
A
Per linear metre $
13294 Pipe laid in trench........................................................................................................................................................................................................................... 1,015.60 13294
13295 Drop pipe to ditto, in manhole........................................................................................................................................................................................................ 1,225.30 13295
Each
13296 Extra over pipe for plug to socket end ........................................................................................................................................................................................... 899.00 13296
13297 Ditto for cap to spigot end .............................................................................................................................................................................................................. 899.00 13297
13298 Ditto for bend ................................................................................................................................................................................................................................. 1,102.20 13298
13299 Ditto for single junction ................................................................................................................................................................................................................. 1,342.90 13299
13300 Ditto for double junction ................................................................................................................................................................................................................ 2,546.90 13300
13301 Ditto for connector to existing pipework........................................................................................................................................................................................ 551.10 13301
13302 Add to either of Items 13298 to 13300 inclusive if fitted with bolted access door ...................................................................................................................... 233.10 13302
Per linear metre
13303 Take up and clear away pipe laid in trench complete with all fittings (trench excavation measured separately)........................................................................ 11.50 13303
13304 Take up and set aside for re-use ditto............................................................................................................................................................................................. 12.80 13304
13305 Break up and clear away concrete beds and surrounds if any including drain
pipes and fittings (trench excavation measured separately)........................................................................................................................................................... 58.00 13305
13306 Take down and clear away drop pipe complete with fittings and brackets .................................................................................................................................. 16.00 13306
13307 Take down and set aside for re-use ditto........................................................................................................................................................................................ 34.40 13307
13308 Lay only pipe in trench.................................................................................................................................................................................................................... 22.10 13308
13309 Fix only drop pipe........................................................................................................................................................................................................................... 117.40 13309
Each
13310 Cut or burn out existing joint, clean spigot and socket ends and make good joint....................................................................................................................... 336.90 13310
13/41
13 PLUMBING AND DRAINAGE 13
Item Item
CAST IRON PIPES AND FITTINGS FOR BELOW GROUND DRAINAGE (CONT'D)
Pipe diameter (mm)
Grey iron pipes and fittings to BS 4622 : 1970, internally and externally coated, for below ground drainage :- 200 250
or 225
A B
Per linear metre $ $
13311 Pipe laid in trench......................................................................................................................................................................................................... 1,125.90 1,244.10 13311
13312 Drop pipe, in manhole................................................................................................................................................................................................... 1,390.40 1,535.40 13312
Each
13313 Extra over pipe for plug to socket end ......................................................................................................................................................................... 899.00 1,007.20 13313
13314 Ditto for cap to spigot end ............................................................................................................................................................................................ 899.00 982.10 13314
13315 Ditto for bend ............................................................................................................................................................................................................... 1,102.20 1,359.50 13315
13316 Ditto for single junction ............................................................................................................................................................................................... 1,342.90 2,108.70 13316
13317 Ditto for double junction .............................................................................................................................................................................................. 2,546.90 3,246.60 13317
13318 Ditto for connector to existing pipework...................................................................................................................................................................... 551.10 679.80 13318
13319 Add to either of Items 13315 to 13317 inclusive if fitted with bolted access door .................................................................................................... 233.10 245.80 13319
Per linear metre
13320 Take up and clear away pipe laid in trench complete with all fittings (trench excavation measured separately)...................................................... 10.20 14.70 13320
13321 Take up and set aside for re-use ditto........................................................................................................................................................................... 12.10 15.30 13321
13322 Break up and clear away concrete beds and surrounds if any including drain pipes and fittings
(trench excavation measured separately)...................................................................................................................................................................... 58.00 63.80 13322
13323 Take down and clear away drop pipe complete with fittings and brackets ................................................................................................................ 16.00 17.90 13323
13324 Take down and set aside for re-use ditto...................................................................................................................................................................... 34.40 37.60 13324
13325 Lay only pipe in trench.................................................................................................................................................................................................. 22.10 24.70 13325
13326 Fix only drop pipe......................................................................................................................................................................................................... 117.10 128.60 13326
Each
13327 Cut or burn out existing joint, clean spigot and socket ends and make good joint..................................................................................................... 336.90 370.10 13327
13/42
13 PLUMBING AND DRAINAGE 13
Item Item
UPVC PIPES AND FITTINGS FOR BELOW GROUND DRAINAGE
UPVC Pressure pipes and fittings to BS 3506 : 1969 for pressurized
drainage with joints and fittings complying with relevant parts of Pipe diameter (mm)
BS 4346-1 : 1969 and BS 4346-2 : 1970 or BS EN ISO 1452-1 : 2009 :- 80 100 125 150 200 250 300
A B C D E F G
Per linear metre $ $ $ $ $ $ $
13328 Pipe laid in trench................................................................................................................ 81.70 122.80 177.40 232.00 313.10 466.20 582.20 13328
Each
13329 Extra over pipe for cap end................................................................................................. 64.10 118.70 180.10 241.50 359.90 466.20 608.60 13329
13330 Ditto for bend or elbow....................................................................................................... 173.00 237.90 350.70 463.60 690.80 894.80 1,168.30 13330
13331 Ditto for tee.......................................................................................................................... 445.60 642.90 794.90 946.80 1,410.80 1,827.40 2,386.10 13331
13332 Ditto for connector to existing pipework............................................................................ 86.50 118.90 175.40 231.80 345.40 447.40 584.20 13332
Per linear metre
13333 Take up and clear away pipe laid in trench
(trench excavation measured separately)............................................................................ 6.40 7.70 8.90 10.90 12.10 13.40 16.00 13333
13334 Take up and set aside for re-use pipe laid in trench (ditto)................................................ 7.70 8.90 10.20 12.10 13.40 14.70 17.20 13334
13335 Lay only pipe in trench........................................................................................................ 8.80 9.70 10.60 11.50 12.40 13.20 14.10 13335
UPVC Pressure pipes and fittings to BS 4660 : 1969 for gravity sewage and surface water drainage :- Pipe diameter (mm)
110 160
A B
Per linear metre $ $
13336 Pipe laid in trench......................................................................................................................................................................................................... 135.10 247.40 13336
Each
13337 Extra over pipe for cap end........................................................................................................................................................................................... 130.60 257.60 13337
13338 Ditto for bend or elbow................................................................................................................................................................................................. 261.70 494.50 13338
13339 Ditto for tee.................................................................................................................................................................................................................... 707.20 1,010.00 13339
13340 Ditto for connector to existing pipework...................................................................................................................................................................... 130.80 247.30 13340
Per linear metre
13341 Take up and clear away pipe laid in trench (trench excavation measured separately)................................................................................................ 8.30 11.50 13341
13342 Take up and set aside for re-use pipe laid in trench (ditto).......................................................................................................................................... 9.60 12.80 13342
13343 Lay only pipe in trench.................................................................................................................................................................................................. 10.60 12.40 13343
13/43
13 PLUMBING AND DRAINAGE 13
Item Item
VALVES
Nominal size (mm)
UPVC or PVC valves : - 15 20 25 30 40 50 65 80
A B C D E F G H
Each $ $ $ $ $ $ $ $
13344 PVC or UPVC screw down valve..................................................................... 64.20 73.20 111.40 141.40 259.60 291.30 - - 13344
13345 Ditto but flanged ............................................................................................... 124.00 150.20 210.20 249.20 311.80 328.20 408.00 489.60 13345
13346 Plastic ball valve with plastic float for flushing cistern.................................... 85.90 96.70 - - - - - - 13346
Copper alloy valves : - Nominal size (mm)
15 20 25 32 40 50 65 80 100 150
A B C D E F G H I J
Each $ $ $ $ $ $ $ $ $ $
13347 Copper alloy gate valve................................................. 128.40 158.00 187.70 223.50 325.90 470.40 644.50 821.00 1,235.80 2,133.40 13347
13348 Ditto but flanged............................................................ - - - - - - - - 1,140.80 2,120.40 13348
13349 Copper alloy non-return valve ...................................... 203.70 244.50 285.20 290.80 395.60 487.10 656.80 992.60 1,507.40 3,500.00 13349
Cast iron valves : - Nominal size (mm)
80 100 125 150 200 250
A B C D E F
Each $ $ $ $ $ $
13350 Cast iron globe valve flanged................................................................................................................ 3,896.80 5,252.20 7,496.10 10,634.80 16,267.70 28,154.70 13350
13351 Cast iron gate valve flanged.................................................................................................................. 1,395.10 1,661.70 2,179.80 3,703.70 4,448.20 8,533.40 13351
Nominal size (mm)
300 350 400
A B C
Each $ $ $
13352 Cast iron globe valve flanged...................................................................................................................................................................... 34,968.40 59,962.50 92,958.90 13352
13353 Cast iron gate valve flanged........................................................................................................................................................................ 12,167.70 - - 13353
13/44
13 PLUMBING AND DRAINAGE 13
Item Item
VALVES (CONT'D)
Nominal size (mm)
Brass or bronze or gunmetal valves : - 15 20 25 30 40 50 65 80
A B C D E F G H
Each $ $ $ $ $ $ $ $
13354 Brass or bronze ball valve with plastic float..................................................... 217.80 268.50 314.10 356.80 507.60 614.30 882.80 1,123.70 13354
13355 Gun metal ball valve with plastic float ............................................................ 316.60 428.20 646.40 852.40 1,119.20 1,299.70 2,342.80 3,010.50 13355
Nominal size (mm)
80 100
A B
Each $ $
13356 Heavy pattern gunmetal full way gate valve ................................................................................................................................................................ 1,017.70 1,528.90 13356
13357 Heavy pattern gunmetal full way gate valve flanged.................................................................................................................................................... 1,150.60 1,736.20 13357
Stainless steel Grade 316 valves : - Nominal size (mm)
15 18 22 28 35 42 54 76 89 108
A B C D E F G H I J
Each $ $ $ $ $ $ $ $ $ $
13358 Stainless steel gate valve .............................................. 328.30 375.20 442.60 495.50 600.90 761.20 1,076.60 2,835.70 3,645.00 4,393.20 13358
13359 Stainless steel check valve ............................................ 256.20 300.00 364.80 458.70 516.40 654.00 904.20 2,588.30 3,028.30 3,714.90 13359
SUNDRIES REPAIRS TO VALVES AND BALL VALVES Nominal size (mm)
15 65 125 200 and
to 50 to 100 to 150 beyond
A B C D
Each $ $ $ $
13360 Take down and clear away valve of all types of materials and functions................................................................................ 12.80 15.30 17.90 20.40 13360
13361 Take down and set aside for re-use valve of all types of materials and functions................................................................... 14.70 17.20 20.40 23.00 13361
13362 Fix only valve of all types of materials and functions.............................................................................................................. 22.10 26.50 30.90 35.30 13362
13/45
13 PLUMBING AND DRAINAGE 13
Item Item
SUNDRIES REPAIRS TO VALVES AND BALL VALVES (CONT'D)
Nominal size (mm)
15 65
to 50 to 80
A B
Each $ $
13363 Take off copper float from ball valve, solder to watertight and re-fix in position....................................................................................................... 53.90 60.40 13363
13364 Take off and clear away existing copper or plastic float from ball valve, provide and fix new plastic float.............................................................. 203.80 252.60 13364
13365 Take off and clear away metal or plastic connecting rod from ball valve, provide and fix new rod.......................................................................... 141.00 172.70 13365
13366 Re-wash ball valve including providing leather, vulcanized fibre, plastic or rubber washer as ordered.................................................................... 66.20 102.40 13366
13367 Re-pack stuffing box, grind in valve and regulate ....................................................................................................................................................... 106.00 220.80 13367
TRAPS AND WASTE
OUTLETS
Supply Take down and Take down and set aside Fix
and fix clear away for re-use only
Nominal size (mm) Nominal size (mm) Nominal size (mm) Nominal size (mm)
32 38 51 32 38 51 32 38 51 32 38 51
A B C D E F G H I J K L
Each $ $ $ $ $ $ $ $ $ $ $ $
13368 Plastic re-sealing
anti-syphonic trap
with 80 mm seal......................... 160.60 199.40 238.20 21.70 23.60 26.20 23.00 24.90 27.40 44.20 53.90 63.60 13368
13369 Galvanized malleable
iron "P", "S" or
running trap with
38 mm or 76 mm seal,
as ordered, and
screwed cleaning
eye including joints
to fitting, waste
outlet, or galvanized
steel or P.V.C.
tubing......................................... 146.70 170.10 218.80 33.80 38.30 43.40 35.10 39.60 44.70 52.10 60.90 73.30 13369
13370 Cast brass ditto........................... 213.10 257.40 349.80 33.80 38.30 44.00 35.10 39.60 44.70 53.00 60.90 73.30 13370
13371 Chromium plated
brass ditto................................... 224.10 261.10 381.80 33.80 38.30 44.00 35.10 39.60 44.70 49.50 57.40 68.90 13371
13372 Add to either of Items
13369 to 13371 inclusive
if fitted with connector for
copper tubing............................. 119.50 145.80 205.50 - - - - - - - - - 13372
13373 Approved "P" or "S"
plastic bottle trap
including joints to
fitting, waste outlet
or P.V.C. tubing......................... 137.00 160.40 - 21.70 23.60 - 23.00 25.50 - 42.40 51.20 - 13373
13/46
13 PLUMBING AND DRAINAGE 13
Item Item
TRAPS AND WASTE
OUTLETS
(CONT'D) Supply Take down and Take down and set aside Fix
and fix clear away for re-use only
Nominal size (mm) Nominal size (mm) Nominal size (mm) Nominal size (mm)
32 38 51 32 38 51 32 38 51 32 38 51
A B C D E F G H I J K L
Each $ $ $ $ $ $ $ $ $ $ $ $
13374 Brass waste outlet
with chromium
plated flange and
grating flynut, long
shank slotted for
overflow if required,
and screwed for
joint to galvanized
steel tubing or trap
including rubber or
vulcanite plug with
chromium plated
ring and chain and
fixing stud if required,
and bedded in red
lead cement in sink
or basin....................................... 161.70 197.60 298.40 23.60 28.70 31.90 25.50 30.60 33.80 40.60 55.60 61.80 13374
13375 Ditto but with
chromium plated
brass overflow grid
and connection for
bath............................................. 187.90 237.50 - 24.90 31.90 - 26.80 33.80 - 45.00 59.20 - 13375
CLEARING TRAPS AND WASTE PIPES
A
Each $
13376 Clear blocked trap and waste pipe complete with combined overflow if necessary to lavatory basin, sink, bath or wall urinal bowl
including taking off and re-fixing cleaning eye from trap, etc., if required and leaving trap and pipe in clean and perfect condition....................................... 42.40 13376
13377 Ditto but for trap and waste pipe to W.C., gully, stall or slab urinal ............................................................................................................................................ 46.80 13377
13/47
13 PLUMBING AND DRAINAGE 13
Item Item
CISTERNS AND TANKS
Take Take
Galvanized low carbon steel cisterns and tanks complete with vent, overflow and warning pipe, Supply down down Fix
accessories, etc. including all joints to tubing : - and and and set only
fix clear aside for
away re-use
A B C D
Each $ $ $ $
13378 Cistern or tank n.e. 100 litre nominal capacity......................................................................................................................... 2,659.80 121.20 42.70 113.00 13378
13379 Ditto but 100 - 200 litre nominal capacity................................................................................................................................ 3,406.00 150.50 50.40 131.60 13379
13380 Ditto but 200 - 300 litre nominal capacity................................................................................................................................ 4,607.30 206.70 67.00 168.70 13380
13381 Ditto but 300 - 500 litre nominal capacity................................................................................................................................ 5,836.90 274.30 102.10 234.00 13381
13382 Ditto but 500 - 1,000 litre nominal capacity............................................................................................................................. 7,986.50 367.40 149.30 346.10 13382
13383 Ditto but 1,000 - 2,000 litre nominal capacity.......................................................................................................................... 10,702.80 483.40 207.90 515.70 13383
13384 Ditto but 2,000 - 3,000 litre nominal capacity.......................................................................................................................... 13,369.60 651.20 254.50 674.60 13384
13385 Ditto but 3,000 - 5,000 litre nominal capacity.......................................................................................................................... 19,144.90 810.00 371.80 1,011.90 13385
13386 Ditto but 5,000 - 10,000 litre nominal capacity........................................................................................................................ 21,787.00 1,581.10 558.10 1,500.20 13386
13387 Add to Item 13386 for each additional 2,500 litres or part thereof in nominal capacity......................................................... 1,938.50 465.00 167.70 280.80 13387
GLASS-FIBRE REINFORCED PLASTIC WATER TANKS
One-piece glass-fibre reinforced plastic (GRP) water tanks with cover complete with vent,
overflow and warning pipe, accessories, etc. including all joints to tubing : - Take Take
Supply down down Fix
(Note: The nominal capacity is measured based on the base area of the tank, measured on plan, and and and set only
and multiplied by the height of the tank, excluding any projection, and multiplied by 1,000 litres/m3.) fix clear aside for
away re-use
A B C D
Each $ $ $ $
13388 Water tank n.e. 100 litre nominal capacity............................................................................................................................... 1,086.80 47.20 33.80 93.60 13388
13389 Ditto but 100 - 250 litre nominal capacity............................................................................................................................... 1,716.60 56.80 40.80 112.10 13389
13390 Ditto but 250 - 350 litre nominal capacity............................................................................................................................... 2,270.10 85.50 61.20 168.70 13390
13391 Ditto but 350 - 500 litre nominal capacity............................................................................................................................... 2,937.80 114.20 81.60 225.20 13391
13392 Ditto but 500 - 800 litre nominal capacity.............................................................................................................................. 3,765.70 165.80 118.60 327.60 13392
13/48
13 PLUMBING AND DRAINAGE 13
Item Item
GLASS-FIBRE REINFORCED PLASTIC WATER TANKS (CONT'D)
Panel type glass-fibre reinforced plastic (GRP) water tank with cover complete
with access ladder if required, roof vent, overflow and warning pipes,
bracing system, accessories, etc. and including all joints to tubing : -
Height (m)
(Note: The area on plan of water tanks is measured the dimensions of the bottom of the tank.) 1.00 1.50 2.00 2.50 3.00
A B C D E
Each $ $ $ $ $
13393 Water tank of area on plan n.e. 2.00 m2....................................................................................................................................................................
8,018.70 11,761.00 14,311.40 17,851.30 26,852.90 13393
13394 Ditto but 2.00 - 4.00 m2......................................................................................................................................................
13,364.80 19,780.40 22,758.70 28,677.80 51,482.00 13394
13395 Ditto but 4.00 - 6.00 m2.....................................................................................................................................................
19,360.20 30,637.10 33,223.00 41,165.40 60,489.50 13395
13396 Ditto but 6.00 - 8.00 m2.....................................................................................................................................................
23,369.90 37,808.00 41,509.20 51,629.00 79,890.90 13396
13397 Ditto but 8.00 - 10.00 m2.....................................................................................................................................................
26,960.20 37,419.40 46,432.10 57,009.60 94,250.30 13397
13398 Ditto but 10.00 - 12.00 m2.....................................................................................................................................................
33,910.70 45,211.80 59,889.20 68,999.10 11,747.11 13398
(The actual rate should be : $117,471.10 for Item 13398E)
13399 Ditto but 12.00 - 16.00 m2.....................................................................................................................................................
39,103.90 54,988.50 67,050.00 76,480.00 13,371.81 13399
(The actual rate should be : $133,718.10 for Item 13399E)
Take down and clear away panel type GRP water tank with cover including all Height (m)
accessories : - 1.00 1.50 2.00 2.50 3.00
A B C D E
Each $ $ $ $ $
13400 Water tank of area on plan n.e. 2.00 m2....................................................................................................................................................................
318.90 446.50 574.00 701.60 1,084.20 13400
13401 Ditto but 2.00 - 4.00 m2......................................................................................................................................................
510.20 701.60 829.10 1,020.50 1,211.80 13401
13402 Ditto but 4.00 - 6.00 m2.....................................................................................................................................................
701.60 892.90 1,084.20 1,403.10 1,913.40 13402
13403 Ditto but 6.00 - 8.00 m2.....................................................................................................................................................
829.10 1,020.50 1,403.10 1,722.00 2,359.80 13403
13404 Ditto but 8.00 - 10.00 m2.....................................................................................................................................................
892.90 1,594.50 1,849.60 2,232.30 2,742.50 13404
13405 Ditto but 10.00 - 12.00 m2.....................................................................................................................................................
1,084.20 1,658.30 2,296.00 2,742.50 3,252.70 13405
13406 Ditto but 12.00 - 16.00 m2.....................................................................................................................................................
1,275.60 1,913.40 2,806.30 3,316.50 4,018.10 13406
13/49
13 PLUMBING AND DRAINAGE 13
Item Item
GLASS-FIBRE REINFORCED PLASTIC WATER TANKS (CONT'D)
Take down and set aside for re-use panel type GRP water tank with cover including all Height (m)
accessories : - 1.00 1.50 2.00 2.50 3.00
A B C D E
Each $ $ $ $ $
13407 Water tank of area on plan n.e. 2.00 m2....................................................................................................................................................................
303.00 424.10 545.30 666.50 1,030.00 13407
13408 Ditto but 2.00 - 4.00 m2......................................................................................................................................................
484.70 666.50 787.70 969.40 1,151.20 13408
13409 Ditto but 4.00 - 6.00 m2.....................................................................................................................................................
666.50 848.30 1,030.00 1,333.00 1,817.70 13409
13410 Ditto but 6.00 - 8.00 m2.....................................................................................................................................................
787.70 969.40 1,333.00 1,635.90 2,241.80 13410
13411 Ditto but 8.00 - 10.00 m2.....................................................................................................................................................
848.30 1,514.70 1,757.10 2,120.60 2,605.40 13411
13412 Ditto but 10.00 - 12.00 m2.....................................................................................................................................................
1,030.00 1,575.30 2,181.20 2,605.40 3,090.10 13412
13413 Ditto but 12.00 - 16.00 m2.....................................................................................................................................................
1,211.80 1,817.70 2,666.00 3,150.70 3,817.10 13413
Fix only panel type GRP water tank with cover including all accessories : - Height (m)
1.00 1.50 2.00 2.50 3.00
A B C D E
Each $ $ $ $ $
13414 Water tank of area on plan n.e. 2.00 m2....................................................................................................................................................................
760.40 1,064.60 1,368.70 1,672.90 2,585.30 13414
13415 Ditto but 2.00 - 4.00 m2......................................................................................................................................................
1,216.60 1,672.90 1,977.00 2,433.30 2,889.50 13415
13416 Ditto but 4.00 - 6.00 m2.....................................................................................................................................................
1,672.90 2,129.10 2,585.30 3,345.70 4,562.40 13416
13417 Ditto but 6.00 - 8.00 m2.....................................................................................................................................................
1,977.00 2,433.30 3,345.70 4,106.10 5,626.90 13417
13418 Ditto but 8.00 - 10.00 m2.....................................................................................................................................................
2,129.10 3,802.00 4,410.30 5,322.80 6,539.40 13418
13419 Ditto but 10.00 - 12.00 m2.....................................................................................................................................................
2,585.30 3,954.10 5,474.80 6,539.40 7,756.00 13419
13420 Ditto but 12.00 - 16.00 m2.....................................................................................................................................................
3,041.60 4,562.40 6,691.50 7,908.10 9,581.00 13420
13/50
13 PLUMBING AND DRAINAGE 13
Item Item
STERILIZER SYSTEM AND DRINKING FOUNTAIN
Take Take
Sterilizer system and drinking fountain including U.V. water sterilizer system/filter and all Supply down down Fix
necessary accessories : - and and and set only
fix clear aside for
away re-use
A B C D
Per Set $ $ $ $
13421 Single-station satin finished stainless steel barrier-free wall mounted drinking fountain 308 mm
long x 165 mm high x 476 mm deep with backsplash comprising safety bubbler; a contoured basin;
vandal-resistant push-button control; vandal-resistant bottom cover plate; and drain and trap
assembly ................................................................................................................................................................................... 5,387.10 83.60 68.30 234.00 13421
13422 Satin finish stainless steel counter top mounted drinking fountain 250 mm diameter x 48 mm deep
comprising safety bubbler; a contoured basin; vandal-resistant push-button control; and drain
and trap assembly ..................................................................................................................................................................... 8,679.60 95.00 77.20 300.20 13422
13423 Satin finished stainless steel wall mounted drinking fountain 305 mm long x 152 mm high x 310 mm
deep comprising polished chrome plated forged brass, integral basin shank, shielded, anti-squirt,
vandal-resistant bubbler head; in-line bowl type strainer with positive rubber seals moulded onto
a fine 60 micron mesh screen; push button activation, front adjustable, automatic diaphragm
pressure regulation with fully adjustable flow; polished chrome-plated brass vandal-resistant
combination waste strainer and tailpiece assembly; a polished chrome plated finish push button
assembly; a low profile trap; and bottom plate with vandal resistant screws ......................................................................... 5,466.50 83.60 68.30 318.80 13423
13424 Reinforced concrete pedestal drinking fountain 362 x 362 x 1016 mm high overall with exposed
aggregate finish comprising polished chrome plated forged brass, integral basin shank, shielded,
anti-squirt, vandal-resistant bubbler head; in-line bowl type strainer with rubber seals moulded
onto a fine 60 micron mesh screen; push button activation, front adjustable, automatic diaphragm
pressure regulation with fully adjustable flow; polished chrome-plated vandal-resistant waste
strainer, a polished chrome plated finish push button; a lead-free brass screwdriver stop; and
integral mounting plate ............................................................................................................................................................ 6,726.90 83.60 68.30 327.60 13424
PRESSURE VESSELS Take Take
Supply down down Fix
Pressure vessel complete with all necessary accessories in accordance with the manufacturer's and and and set only
recommendations : - fix clear aside for
away re-use
A B C D
Per Set $ $ $ $
13425 Pressure vessel, vertical type, of 10 bar working pressure and 60 litres capacity .................................................................. 2,432.90 95.70 107.80 337.30 13425
13426 Ditto but 200 litres capacity ..................................................................................................................................................... 3,815.20 135.20 158.20 468.00 13426
13427 Ditto but 300 litres capacity ..................................................................................................................................................... 5,451.70 181.80 218.80 794.70 13427
13428 Ditto but 500 litres capacity ..................................................................................................................................................... 6,955.50 237.90 292.70 843.30 13428
13429 Ditto but 1,000 litres capacity .................................................................................................................................................. 18,353.10 358.40 430.50 1,180.60 13429
13/51
13 PLUMBING AND DRAINAGE 13
Item Item
BALLOON GRATINGS AND FRESH AIR INLETS
Supply Take Take
and down down Fix
fix and and set only
Nominal size (mm) clear aside for
51 75 100 150 away re-use
A B C D E F G
Each $ $ $ $ $ $ $
13430 Stout galvanized iron wire balloon grating with pronged feet and set
in top of pipe ....................................................................................................................... 29.10 43.70 58.20 87.30 7.70 8.90 9.70 13430
13431 Stout copper wire ditto ....................................................................................................... 87.30 131.00 174.60 262.00 7.70 8.90 9.70 13431
Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Each $ $ $ $
13432 Galvanized cast iron fresh air inlet valve with brass front and mica flap, and joint to top
of 100 mm cast iron pipe .......................................................................................................................................................... 232.80 33.20 35.10 51.20 13432
A
Each $
13433 Take off and clear away existing mica flap, and provide and fix new .......................................................................................................................................... 65.30 13433
FIRE COLLAR
Pipe diameter (mm)
15 20 25 32 40 50 65 80 100 150
A B C D E F G H I J
Each $ $ $ $ $ $ $ $ $ $
13434 Pyrosleeve 'GV' type fire collar as ordered
by the Maintenance Surveyor in writing ...................... 89.00 90.80 93.40 97.00 106.80 113.20 124.60 141.50 161.70 214.30 13434
GRANULAR BEDS FOR DRAIN PIPES
Granular bedding :
A
Per cubic metre $
13435 Beds, haunching or surrounds to pipe............................................................................................................................................................................................ 184.10 13435
13/52
13 PLUMBING AND DRAINAGE 13
Item Item
CONCRETE BEDS FOR DRAIN PIPES
Pipe bore (mm)
Concrete Grade 10S, Grade 10D or 10MPa in : - 50 75 80 100 110 150 160 200
A B C D E F G H
Per linear metre $ $ $ $ $ $ $ $
13436 Bed 300 mm wider than external diameter of pipe
and 100 mm thick under pipe including haunching
up after drain is tested from outside edge of bed
to meet pipe barrel tangentially......................................................................... 38.00 44.60 45.80 52.20 55.20 67.00 - - 13436
13437 Ditto but 150 mm thick under pipe including filling up after
the drain is tested to mid point of pipe barrel................................................... 70.50 85.20 87.50 98.90 104.70 127.40 134.20 158.10 13437
13438 Add to Item 13437 if pipe is completely surrounded
after testing with similar concrete not less than 150 mm
thick all round.................................................................................................... 41.00 47.90 48.90 54.80 58.70 70.40 73.00 86.50 13438
Pipe bore (mm)
225 250 300 315 350 375 400 450
A B C D E F G H
Per linear metre $ $ $ $ $ $ $ $
13439 Bed 300 mm wider than external diameter of pipe and 150 mm
thick under pipe including filling up after the drain is tested
to mid point of pipe barrel................................................................................. 204.10 222.80 240.10 251.50 278.50 286.70 305.90 324.10 13439
13440 Add to Item 13439 if pipe is completely surrounded after testing
with similar concrete not less than 150 mm thick all round............................. 90.00 97.10 105.60 110.50 120.10 126.50 133.80 136.90 13440
Extra over either of Items 13436 to 13440 inclusive for concrete Grade 20S, Grade 20D or 20MPa ........................................................................................ 13%
13/53
13 PLUMBING AND DRAINAGE 13
Item Item
CAST IRON TRAPS AND GULLIES
Traps and gullies with concrete Grade 20S, Grade 20D or 20MPa bed and surround minimum Take Take
100 mm thick all round : - Supply up up Fix
and and and set only
(Note : - All Items 13441 to 13456 (Columns (A) to (D)) inclusive include for concrete bed fix clear aside for
and surround or breaking up the same as applicable.) away re-use
A B C D
Each $ $ $ $
13441 Trap with 50 mm bore outlet..................................................................................................................................................... 171.70 16.60 23.60 97.20 13441
13442 Ditto 75 mm ditto...................................................................................................................................................................... 225.00 20.40 28.70 110.80 13442
13443 Ditto 100 mm ditto.................................................................................................................................................................... 271.10 25.50 35.70 150.60 13443
13444 Ditto 150 mm ditto.................................................................................................................................................................... 423.40 33.20 46.60 183.00 13444
13445 Ditto 225 mm ditto.................................................................................................................................................................... 759.90 53.60 74.60 266.60 13445
13446 Gully with 100 mm bore trapped outlet and 150 mm diameter circular or 150 x 150 mm
square top rebated for grating (measured separately)............................................................................................................... 404.70 34.40 47.80 187.20 13446
13447 Ditto but with 150 mm bore trapped outlet and 225 mm diameter circular or 225 x 225 mm
square top ditto (ditto)............................................................................................................................................................... 619.80 38.90 54.90 219.60 13447
13448 Add to either of Items 13446 to 13447 inclusive for side or back inlet................................................................................... 189.10 21.10 29.30 87.80 13448
13449 Grit or grease gully with 100 mm bore trapped outlet and 225 mm diameter circular or 225 x
225 mm square top rebated for grating (measured separately) complete with removable
galvanized steel strainer and handle......................................................................................................................................... 1,027.10 33.20 46.60 210.20 13449
13450 Intercepting trap with 100 mm bore outlet and square or oblique inspection arm fitted with
galvanized stopper in plain or screw pattern joint.................................................................................................................... 416.80 28.10 38.90 97.20 13450
13451 Ditto but with 150 mm bore outlet ditto................................................................................................................................... 605.30 34.40 47.80 125.50 13451
13452 Ditto but with 225 mm bore outlet ditto................................................................................................................................... 935.10 46.60 65.10 158.90 13452
13453 Ditto but with 300 mm bore outlet ditto................................................................................................................................... 1,260.40 68.90 96.30 187.20 13453
13454 Ditto but with 375 mm bore outlet ditto................................................................................................................................... 2,109.80 102.70 144.10 222.70 13454
13455 Ditto but with 600 mm bore outlet ditto................................................................................................................................... 3,449.60 155.00 216.90 364.90 13455
13456 Add to either of Items 13450 to 13455 inclusive if fitted with cast iron stopper and lever handle,
1.80 m long galvanized chain, hook and ring........................................................................................................................... 60.50 - - - 13456
13/54
13 PLUMBING AND DRAINAGE 13
Item Item
VITRIFIED CLAY TRAPS AND GULLIES
Traps and gullies with concrete Grade 20S, Grade 20D or 20MPa bed and surround minimum Take Take
100 mm thick all round : - Supply up up Fix
and and and set only
(Note : - All Items 13457 to 13474 (Columns (A) to (D)) inclusive include for concrete bed fix clear aside for
and surround or breaking up the same as applicable.) away re-use
A B C D
Each $ $ $ $
13457 Trap with 100 mm bore outlet................................................................................................................................................... 149.60 19.10 26.80 179.80 13457
13458 Ditto with 150 mm ditto............................................................................................................................................................ 210.70 23.00 33.80 125.50 13458
13459 Ditto with 225 mm ditto............................................................................................................................................................ 447.80 32.50 45.90 163.10 13459
13460 Ditto with 300 mm bore outlet.................................................................................................................................................. 807.50 48.50 61.20 201.80 13460
13461 Gully with 100 mm bore trapped outlet and 150 mm diameter circular or 150 x 150 mm
square top rebated for grating (measured separately)............................................................................................................... 254.70 31.90 54.90 163.10 13461
13462 Ditto but with 150 mm bore trapped outlet and 225 mm diameter circular or 225 x 225 mm
square top ditto (ditto)............................................................................................................................................................... 514.60 37.60 61.20 191.30 13462
13463 Add to either of Items 13461 to 13462 inclusive for side or back inlet of any bore............................................................... 115.40 - - - 13463
13464 Grit or grease gully with 100 mm bore trapped outlet and 225 mm diameter circular or 225 x
225 mm square top rebated for grating (measured separately) complete with removable
galvanized steel strainer and handle......................................................................................................................................... 662.50 37.00 61.20 153.70 13464
13465 Road gully, 300 mm diameter and 600 mm deep, with plain top and 100 mm or 150 mm bore outlet................................. 929.10 73.30 115.40 294.90 13465
13466 Ditto but 300 mm diameter and 750 mm deep ditto................................................................................................................. 1,014.90 77.20 126.90 332.50 13466
13467 Ditto but 375 mm diameter and 900 mm deep ditto................................................................................................................. 1,184.20 89.90 141.60 397.30 13467
13468 Add to either of Items 13465 to 13467 inclusive for cleaning eye with sealing plate or stopper........................................... 38.50 - - - 13468
13469 Intercepting trap with 100 mm bore outlet and square or oblique inspection arm fitted with
clayware stopper in plain or screw pattern joint....................................................................................................................... 511.20 22.30 33.80 103.50 13469
13470 Ditto but with 150 mm bore outlet ditto................................................................................................................................... 706.40 26.80 41.50 120.20 13470
13471 Ditto but with 225 mm bore outlet ditto................................................................................................................................... 1,108.10 38.30 58.00 149.50 13471
13472 Ditto but with 300 mm bore outlet ditto................................................................................................................................... 1,707.90 55.50 71.40 181.90 13472
13473 Ditto but with 375 mm bore outlet ditto................................................................................................................................... 2,117.30 66.30 84.80 210.20 13473
13474 Add to either of Items 13469 to 13473 inclusive if fitted with galvanized iron stopper and lever
handle, 1.80 m long galvanized chain, hook and ring.............................................................................................................. 37.80 - - - 13474
13/55
13 PLUMBING AND DRAINAGE 13
Item Item
PRECAST CONCRETE GULLIES
Gullies with concrete Grade 20S, Grade 20D or 20MPa bed and surround minimum Take Take
100 mm thick all round : - Supply up up Fix
and and and set only
(Note : - All Items 13475 to 13476 (Columns (A) to (D)) inclusive include for concrete bed fix clear aside for
and surround or breaking up the same as applicable.) away re-use
A B C D
Each $ $ $ $
13475 Road gully, 225 mm diameter and 600 mm deep internally with plain top and 100 or 150 mm
bore outlet.................................................................................................................................................................................. 832.20 102.10 74.60 472.60 13475
13476 Ditto but size 450mm diameter and 900mm deep internally................................................................................................... 1,532.00 176.70 135.20 755.90 13476
GULLY KERBS, HOPPERS AND GRATINGS
Size of gully top (mm)
150 x 150 225 x 225
75 or 150 or 225
diameter diameter diameter
A B C
Each $ $ $
13477 Kerb 75 mm thick and n.e. 150 mm high, around two or three sides of gully top, of concrete Grade 10S,
Grade 10D or 10MPa or bricks-on-edge in cement mortar, rendered in 15 mm thick cement and sand (1:3)
trowelled smooth on all exposed surfaces and dished to gully, including all necessary formwork......................................................... 29.30 49.10 73.20 13477
13478 Extra for raising concrete surround to trap or gully to a height n.e. 300 mm above top to
form hopper (or alternatively providing and fixing glazed clayware or cast iron raising piece
surrounded with and including 100 mm thick concrete) including forming rebate around top
if required for grouting (measured separately), trowelling all surfaces smooth with cement
and sand (1:2), forming all back inlets, and all additional excavation, disposal and formwork............................................................... 66.20 113.50 160.80 13478
13479 Add to Item 13478 for each additional 150 mm or part thereof in height................................................................................................. 28.40 56.70 75.70 13479
13480 Galvanized steel or coated cast iron flat or dished grating and set in gully top or concrete surround to
trap or gully................................................................................................................................................................................................. 47.30 66.20 75.70 13480
13481 Take up and clear away galvanized steel or coated cast iron flat or dished grating set in gully top or
concrete surround to trap or gully............................................................................................................................................................... 3.20 3.80 4.50 13481
13482 Take up and set aside for re-use ditto......................................................................................................................................................... 5.10 6.40 7.00 13482
13483 Fix only ditto................................................................................................................................................................................................ 4.20 5.20 6.30 13483
13484 Galvanized steel or coated cast iron flat or dished hinged grating and frame and set frame in gully top
or concrete surround to trap or gully........................................................................................................................................................... 106.10 123.80 132.70 13484
13485 Take up and clear away galvanized steel or coated cast iron flat or dished hinged grating and frame set
in gully top or concrete surround to trap or gully....................................................................................................................................... 3.80 4.50 5.10 13485
13486 Take up and set aside for re-use ditto......................................................................................................................................................... 6.40 7.00 8.90 13486
13487 Fix only ditto................................................................................................................................................................................................ 8.40 11.50 13.60 13487
13/56
13 PLUMBING AND DRAINAGE 13
Item Item
SURFACE WATER CHANNELS
A
Per cubic metre $
13488 Concrete Grade 20S, Grade 20D or 20MPa in surface water channel n.e. 0.10 m cross sectional area (void of waterway
not deducted) with 75mm (minimum) thick sides and base, level or slope.................................................................................................................................. 1,134.80 13488
13489 Ditto 0.10 - 0.20 m cross sectional area........................................................................................................................................................................................ 993.00 13489
13490 Ditto 0.20 - 0.40 m cross sectional area........................................................................................................................................................................................ 851.10 13490
Add to either of Items 13488 to 13490 inclusive if cast to curve n.e. 3.00 m radius to centre line of waterway......................................................................... 25%
13491 Add to either of Items 13488 to 13490 inclusive for breaking up and carting away existing concrete surface water channel
and step surface water channel including clearing away channel cover and any silting in channel, if required.......................................................................... 151.30 13491
13492 Add to either of Items 13488 to 13490 inclusive for forming step surface water channel including ditto.................................................................................. 37.80 13492
CAST IRON CHANNEL COVERS
Take Take
Supply up up Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per kg $ $ $ $
13493 Cast iron surface channel cover with slots, weight n.e. 24 kg each......................................................................................... 6.00 1.30 1.90 3.10 13493
13494 Ditto, weight exceeding 24 kg each.......................................................................................................................................... 5.80 0.60 1.30 3.10 13494
PRECAST CONCRETE CHANNEL COVERS
Take Take
Supply up up Fix
and and and set only
fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
13495 Precast concrete Grade 20S, Grade 20D or 20MPa channel cover with slots, 25 mm thick
including reinforcement............................................................................................................................................................ 340.50 36.40 45.30 60.60 13495
13496 Ditto but 50 mm thick............................................................................................................................................................... 397.20 47.20 56.10 95.20 13496
13/57
13 PLUMBING AND DRAINAGE 13
Item Item
MANHOLES, CESSPITS, SEPTIC TANKS, CATCHPITS, GREASE PITS AND OTHER
DRAINAGE CHAMBERS
Plain Reinforced
Plain and/or reinforced concrete Grade 20S, Grade 20D or 20MPa (reinforcement and formwork measured separately) : - concrete concrete
A B
Per cubic metre $ $
13497 Base slabs...................................................................................................................................................................................................................... 570.90 629.70 13497
13498 Walls.............................................................................................................................................................................................................................. 621.50 638.40 13498
13499 Suspended slabs............................................................................................................................................................................................................ 570.90 629.70 13499
Extra over either of Items 13497 to 13499 inclusive for plain and/or reinforced concrete Grade 25S, Grade 25D or 25Mpa................................................... 8%
Extra over either of Items 13497 to 13499 inclusive for plain and/or reinforced concrete Grade 30S, Grade 30D or 30Mpa................................................... 10%
Extra over either of Items 13497 to 13499 inclusive for plain and/or reinforced concrete Grade 40S, Grade 40D or 40Mpa................................................... 19%
Sawn Wrot
formwork formwork
A B
Per square metre $ $
13500 Formwork to base slabs................................................................................................................................................................................................. 129.10 137.70 13500
13501 Formwork to walls......................................................................................................................................................................................................... 202.60 211.20 13501
13502 Formwork to soffit of suspended slabs......................................................................................................................................................................... 199.90 208.50 13502
Per linear metre
13503 Formwork to edges n.e. 75 mm wide............................................................................................................................................................................ 22.60 23.50 13503
13504 Ditto but 75 - 150 mm wide.......................................................................................................................................................................................... 39.50 41.30 13504
13505 Ditto but 150 - 225 mm wide........................................................................................................................................................................................ 52.60 55.90 13505
A
Per square metre $
13506 Concrete Grade 20S, Grade 20D or 20MPa benching and channels in any thickness.................................................................................................................. 114.20 13506
13/58
13 PLUMBING AND DRAINAGE 13
Item Item
CAST IRON MANHOLE COVERS AND FRAMES
Take Take
Supply up up Fix
and and and set only
fix clear aside for
away re-use
A B C D
Each $ $ $ $
13507 Manhole cover and frame, approximately 37kg....................................................................................................................... 225.70 47.80 65.10 40.80 13507
13508 Ditto, approximately 52kg......................................................................................................................................................... 315.20 64.40 104.00 53.30 13508
13509 Ditto, approximately 143kg....................................................................................................................................................... 848.20 83.60 114.20 152.70 13509
13510 Ditto, approximately 178kg....................................................................................................................................................... 1,120.50 104.60 145.40 165.20 13510
13511 Ditto, approximately 192kg....................................................................................................................................................... 1,140.00 113.50 155.60 173.60 13511
13512 Ditto, approximately 308kg....................................................................................................................................................... 1,820.90 176.70 238.50 278.10 13512
13513 Circular manhole cover and manhole frame, approximately 95kg.......................................................................................... 568.10 54.90 76.50 94.10 13513
13514 Double triangular manhole cover and frame approximately 140kg......................................................................................... 832.60 84.20 113.50 135.90 13514
13515 Gully sump cover and frame, approximately 69kg................................................................................................................... 412.40 40.80 53.60 70.10 13515
13516 Ditto, approximately 83kg......................................................................................................................................................... 498.00 46.60 65.10 80.50 13516
Deduct from any of Items 13507 to 13516 inclusive for work of manhole cover only or
gully sump cover only............................................................................................................................................................... - - ( 30% ) ( 30% )
STEP IRONS
A
Each $
13517 Manhole step irons built into concrete or grouted into existing mortice....................................................................................................................................... 59.20 13517
13518 Cut out and clear away existing step iron including making good side or cutting mortice ready to receive new
step iron (measured separately)...................................................................................................................................................................................................... 11.50 13518
13/59
13 PLUMBING AND DRAINAGE 13
Item Item
ALTERATION TO EXISTING MANHOLES
A
Per square metre $
13519 Hack up existing defective benching of any thickness and re-form with concrete Grade 20S, Grade 20D or 20MPa
rendered smooth in 20 mm thick cement and sand (1:3) including forming channels................................................................................................................. 146.40 13519
Pipe bore (mm)
50 75 100 150 225
A B C D E
Each $ $ $ $ $
13520 Block up pipe entering manhole for a length of 300 mm with concrete
Grade 10S, Grade 10D or 10MPa and make good face of manhole wall.............................................................. 29.20 30.30 40.30 45.40 60.50 13520
13521 Cut hole through manhole wall for new pipe entering above manhole
invert level and made good..................................................................................................................................... 21.60 43.30 48.70 59.50 91.90 13521
13522 Ditto but for new pipe entering at manhole invert level including
cutting out and re-forming benching as necessary, and forming new
channel and make good........................................................................................................................................... 199.20 213.80 243.00 252.70 320.70 13522
A
Per cubic metre $
13523 Break up existing manhole and fill in void with graded aggregates or approved hardcore well rammed.................................................................................... 95.70 13523
REPAIRS TO LEAKING BURIED WATER-CARRYING SERVICES
(Note : - The following Items 13524 to 13525 inclusive will only be paid for, if ordered by the Maintenance Pipe bore Pipe bore
Surveyor in writing.) n.e. 300 -
300 mm 600 mm
A B
Each $ $
13524 Prepare and apply approved internal lining of continuous length not exceeding 2500 mm for all types of leaking
pipework and fittings laid in trench.............................................................................................................................................................................. 3,864.00 5,796.00 13524
Per linear metre
13525 Extra over Item 13524 for preparing and applying approved internal lining of continuous length exceeding 2500 mm
for all types of leaking pipework and fittings laid in trench........................................................................................................................................ 1,436.10 2,154.10 13525
13/60
13 PLUMBING AND DRAINAGE 13
Item Item
SUB-SOIL DRAIN PIPES AND DRAINAGE LAYER
Supply and lay : -
A
Per square metre $
13526 Proprietary non-woven geotextile filter.......................................................................................................................................................................................... 14.80 13526
Supply and lay : - Pipe bore (mm)
100 150 200 300 450
A B C D E
Per linear metre $ $ $ $ $
13527 Perforated plastic pipe laid in trench...................................................................................................................... 332.80 442.70 885.40 1,936.90 3,486.30 13527
WEEPHOLES THROUGH RETAINING WALLS
Pipe bore (mm)
75 100 150
A B C
Per linear metre $ $ $
13528 Form weep holes through concrete walls with and including PVC pipe cast in on rake.......................................................................... 20.30 30.50 50.80 13528
13529 Ditto but through brick or stone wall ditto................................................................................................................................................. 20.30 30.50 50.80 13529
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION
(Note : All Items 13530 to 13568 inclusive included under Services for Plumbing and Drainage Installation (the Installation) will only
be paid for, if ordered by the Maintenance Surveyor in writing.)
SERVICES PROVIDED FOR ENHANCED EXECUTION WORKS
FOR THE PLUMBING AND DRAINAGE INSTALLATION Installation Value ($ million)
Upto 0.50 to 1.50 to Exc.
0.50 1.50 3.00 3.00
A B C D
Per item $ $ $ $
13530 Provide installation drawings.................................................................................................................................................... 18,191.30 30,318.80 48,510.00 60,637.50 13530
13531 Provide as-built drawings.......................................................................................................................................................... 18,537.80 30,665.30 48,856.50 60,984.00 13531
13532 Provide operation and maintenance manual............................................................................................................................. 17,671.50 29,452.50 46,431.00 58,212.00 13532
13533 Provide annual operation and maintenance services................................................................................................................ 4,473.60 6,421.60 8,369.60 10,317.60 13533
13/61
13 PLUMBING AND DRAINAGE 13
Item Item
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION (CONT'D)
SERVICES PROVIDED TO FRESH WATER PLUMBING SYSTEM AND
QUALITY WATER RECOGNITION SCHEME (QWRS) FOR BUILDINGS No. of floors
of building
Carry out inspection to the fresh water plumbing system : - N.e. 20 Exc. 20
A B
Per inspection $ $
13534 Inspection of residential buildings................................................................................................................................................................................ 7,507.50 12,993.80 13534
13535 Ditto of schools and institutions................................................................................................................................................................................... 6,496.90 8,662.50 13535
13536 Ditto of police stations, fire stations and ambulance depots........................................................................................................................................ 8,662.50 - 13536
13537 Ditto of hospitals, clinics and health buildings............................................................................................................................................................ 17,325.00 25,987.50 13537
13538 Ditto of correctional institutions and related buildings................................................................................................................................................ 21,656.30 34,650.00 13538
13539 Ditto of museums, cultural buildings, community centres, community halls and libraries........................................................................................ 8,662.50 - 13539
13540 Ditto of public toilets, bathhouses and refuse collection points.................................................................................................................................. 4,331.30 - 13540
13541 Ditto of municipal buildings, markets, cooked food centres, slaughterhouses, public mortuaries and funeral parlours.......................................... 10,828.10 - 13541
13542 Ditto of offices, law courts and post offices................................................................................................................................................................. 12,993.80 21,656.30 13542
13543 Ditto of indoor game halls, recreation centres, swimming pools and coliseums......................................................................................................... 8,662.50 - 13543
13544 Ditto of laboratories and science buildings.................................................................................................................................................................. 10,828.10 18,900.40 13544
A
Per number $
13545 Cleaning of water tank of internal volume not exceeding 10 m................................................................................................................................................... 2,055.80 13545
13546 Ditto 10 m to 20 m........................................................................................................................................................................................................................ 2,398.40 13546
13547 Ditto 20 m to 30 m........................................................................................................................................................................................................................ 2,741.10 13547
13548 Ditto 30 m to 50 m........................................................................................................................................................................................................................ 3,426.30 13548
13549 Ditto 50 m to 100 m...................................................................................................................................................................................................................... 4,672.20 13549
13550 Add to Item 13549 for each additional 10 m or part thereof in internal volume.......................................................................................................................... 241.40 13550
13551 Carry out sampling for water quality examination ........................................................................................................................................................................ 462.00 13551
13552 Conduct water analysis of fresh water for water quality examination........................................................................................................................................... 485.10 13552
13/62
13 PLUMBING AND DRAINAGE 13
Item Item
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION (CONT'D)
SERVICES PROVIDED TO CLEANING AND CLEARANCE OF UNDERGROUND
FOUL AND WASTE WATER DRAINAGE SYSTEM AT MARKET COMPLEXES
AND COOKED FOOD CENTRES
Cleaning and clearance of underground foul and waste water drainage system and grease tanks
at market complexes and cooked food centres, including provision of CCTV inspection survey : -
A
Per item $
13553 Market complexes or cooked food centre of paved area not exceeding 5,000 m2............................................................................................................................................
3,888.60 13553
13554 Add to Item 13553 for each additional 750 m2 or part thereof in paved area.................................................................................................................................... 510.20 13554
Cleaning and clearance of underground foul and waste water drainage system and grease tanks
at market complexes and cooked food centres : -
Per item
13555 Market complexes or cooked food centre of paved area not exceeding 5,000 m2....................................................................................................................................
3,280.30 13555
13556 Add to Item 13555 for each additional 750 m2 or part thereof in paved area.................................................................................................................................... 255.10 13556
SERVICES FOR INSPECTION, TESTING AND CLEANING OF EXISTING DRAINAGE SYSTEM
UTILITIES SURVEY
A
Per square metre $
13557 Carry out utilities survey by an approved specialist to ascertain the alignment of the buried/exposed
existing underground utilities/services and related surface features, including power cables, gas pipes,
telecommunication lines, cable TV, water mains, drainage, fuel tank and pipes, fire hydrants, valve
chambers/pits, manholes, combined services ducts, etc., within and in the vicinity of the site; determine the
sizes and the horizontal and vertical alignments of these utilities by means of electromagnetic induction
method including submission of survey report in 2 copies, record drawings, photo records, text reports
and layout plan and 2 sets of CD-ROMS....................................................................................................................................................................................... 104.60 13557
DETECTION OF LEAKING BURIED WATER PIPES
Per linear metre
13558 Carry out acoustic water leakage detection works by an approved specialist including leak noise correlation survey, ground
microphone survey for identification of the location of any possible leakage along the pressurized fresh water and flush water
supply pipes within the hatched areas, including submission of survey report in 2 copies, record drawings, photo records, text
reports and layout plan and 2 sets of CD-ROMs............................................................................................................................................................................ 115.00 13558
13/63
13 PLUMBING AND DRAINAGE 13
Item Item
SERVICES FOR PLUMBING AND DRAINAGE INSTALLATION (CONT'D)
SERVICES FOR INSPECTION, TESTING AND CLEANING OF EXISTING DRAINAGE SYSTEM Pipe
(CONT'D) bore
n.e.
CLEANING OF EXISTING DRAINAGE SYSTEM 300 mm
A
Per item $
13559 Cleaning of existing drainage system including manholes, cesspits, septic tanks, catch pits, grease pits, and
other drainage chambers including branches and connection by using high pressure water jet up to 2200 PSI
and 262 litre/min. by an approved specialist for a period not exceeding 4 hours......................................................................................................................... 1,292.30 13559
13560 Add to Item 13559 for each additional 4 hours or part thereof in hour......................................................................................................................................... 928.50 13560
Each
13561 Cleaning existing manholes, cesspits, septic tanks, catch pits, grease pits, or other drainage chambers n.e. 6.0 m including
branches and connections by sludge and sewage vacuum pump/sucker with branch up to 204mm diameter including hoses
n.e. 100 metre long.......................................................................................................................................................................................................................... 903.40 13561
13562 Add to Item 13561 for each additional 6.0 m or part thereof in volume...................................................................................................................................... 688.00 13562
13563 Cleaning existing manholes, cesspits, septic tanks, catch pits, grease pits, or other drainage chambers n.e. 2.0 m including
branches and connections by using methods other than high pressure water jet or vacuum pump/sucker.................................................................................. 341.90 13563
13564 Add to Item 13563 for each additional 2.0 m or part thereof in volume...................................................................................................................................... 46.00 13564
CCTV INSPECTION SURVEY TO EXISTING DRAINAGE SYSTEM
Pipe
bore
n.e.
300 mm
A
Per item $
13565 Carrying out CCTV inspection survey to existing drainage system by an approved specialist for a period not
exceeding 4 hours............................................................................................................................................................................................................................ 3,032.40 13565
13566 Add to Item 13565 for each additional 4 hours or part thereof in hour......................................................................................................................................... 2,021.60 13566
TESTING EXISTING DRAINS
A
Each $
13567 Water test as described to existing branch or drain between manholes, up to 150 mm diameter................................................................................................. 243.60 13567
13568 Ditto but for 150 - 300 mm diameter.............................................................................................................................................................................................. 315.80 13568
13/64
Section 14
GLAZING
14 GLAZING 14
SECTION 14
GLAZING
SPECIAL CONDITIONS
Measurement SC14.01 Glazing works shall be measured the net area as glazed. No deduction shall be made for
generally opening not exceeding 0.50 m.
Panes of glass of circular or irregular shape shall be measured the smallest rectangular or
square out of which such circular or irregular shape can be cut.
Special glazing works shall only be paid when specifically ordered by the Maintenance
Surveyor in writing.
Window and door films shall be measured the net area covered.
Glazing to timber doors including glazing to observation panel/openings is included in the
respective timber door items in Section 08 - Carpentry and Joinery and will not be measured
separately in this Section unless specifically instructed otherwise.
Measurement SC14.02 All finished works shall include for cutting to the required sizes. No measurement shall be
of cutting made unless the glass is not supplied by the Contractor himself.
Forming holes through glass shall be measured separately. In the case of forming hole
through existing fixed glass. Take down and set aside for re-use and Fix only shall be
measured separately.
Forming hole exceeding 0.20 m through glass shall be measured as straight or circular
cutting.
Measurement SC14.03 Fire resisting glass block panels shall be measured by the net area of the structural opening
of fire of the glass block panels as fixed. No deduction shall be made for voids not exceeding
resisting glass 0.50 m.
block panels
Rates for SC14.04 The rates for glazing shall generally include for : -
glazing
generally (a) Panes or sheets in any size unless otherwise stated, fixed in any positions and
including all colours.
(b) All cutting and waste, breakage and replacing scratched or cracked pane.
(c) Painting to wood or steel beads and rebate surfaces with one coat of priming
paint before glazing.
(d) Providing all putty or glazing compound, plastic setting and location blocks, pointing
and sealing junctions between glass and glazing beads or the like with approved
sealant materials; or in the case of glazing with beads, for taking off and re-fixing
wood beads supplied by the joiner or metal beads supplied with metal windows.
14/1
14 GLAZING 14
SPECIAL CONDITIONS
Rates for SC14.04 (e) Painting cut edges of wired glass with bitumastic paint.
glazing (Cont'd)
generally (f) Protecting and cleaning.
(Cont'd)
(g) Fixing in accordance with the manufacturer's instructions.
Rates for SC14.05 The rates for glazing of louvre blades shall further include for : -
glazing of
louvre blades (a) Fixing in adjustable metal clips including adjusting and oiling clips.
(b) Fixing in fixed metal clips.
(c) Making good surfaces disturbed.
Rates for SC14.06 The rates for take out and clear away or take out and set aside for re-use glass or glass
take out blockwork shall further include for : -
glass, glass
blocks, etc. (a) Hacking out old putty and cleaning glass, blockwork and window bead and
frames.
(b) Protecting and storing glass or blockwork and metal beads.
Rates for forming SC14.07 The rates for forming holes through glass shall further include for : -
holes through
glass (a) Cutting holes in any size and polishing all edges.
(b) Forming holes in any size.
Rates for SC14.08 The rates for fully tempered glass shall further include for : -
fully tempered
glass (a) Glass that has been treated under heat soak testing and conforming to the relevant
safety glass requirements determined by the required testing standards as G.S.
Items 20.01.01, 20.01.05 and 20.08.
(b) Submission of methodology of the heat soak testing to the Maintenance
Surveyor's approval.
(c) Provision of a quality supervision plan for a quality supervisor of the manufacturer's
heat soak process.
(d) Provision of a full time technically competent persons (TCP) with experience and
qualification accepted by the Maintenance Surveyor and the TCP shall supervise
the heat soak process in the manufacturer's factory.
(e) Submission of compliance test certificates and manufacturer's guarantee.
14/2
14 GLAZING 14
SPECIAL CONDITIONS
Rates for SC14.09 The rates for polycarbonate sheet shall further include for : -
polycarbonate
sheet (a) All cutting and waste, breakage and replacing scratched or cracked pane.
(b) All cold or heat bent to shape and fixing to metal or wood frames.
(c) In the case of fixing to metal or wood frames, drilling holes for and providing all
drive screws, self-tapping screws, rivets, bolts, hook, bolts, nuts, metal and
rubber washers, and plastic caps for fixing to purlins or framing spaced at any
interval.
(d) Drilling holes to existing or new purlins or framing spaced at any interval the fixing
of polycarbonate sheet as required.
Rates for SC14.10 The rates for laminated glass shall further include for : -
laminated
glass (a) Laminated glass, either as a safety glass or a security glass, in conformity to the
relevant safety class requirements determined by the required testing standards as
G.S. Items 20.01.01 and 20.11.
(b) Two or more sheets of glass bonded together incorporating a plastic inlay of the
required thickness.
(c) Laminated glass conforming to category 1 as a minimum standard and/or
categories 2 or 3 as may be required, all as specified in G.S. Item 20.11(ii).
(d) Submission of test certificates and manufacturer's guarantee.
Rates for SC14.11 The rates for bullet or blast resistant laminated safety glass shall further include for : -
bullet or
blast resistant (a) Adding an applied adhesive film, either to the external face or the internal face,
laminated if required.
safety glass
(b) Submission of test certificates and manufacturer's guarantee.
Rates for SC14.12 The rates for fire rated glass shall further include for : -
fire rated
glass (a) Supply of fire rated glass with insulation and integrity of the fire resistance period
in accordance with the testing standards as stated in G.S. Item 20.05 and
complying with the latest fire safety code and relevant statutory requirements.
(b) Providing and filling jambs and head of panels with expansion strips, joint filler
and sealant of fire resisting type.
(c) Submission of test certificates and manufacturer's guarantee.
14/3
14 GLAZING 14
SPECIAL CONDITIONS
Rates for SC14.13 The rates for glass block panels shall further include for : -
glass block
panels (a) Painting all sides of structural opening to receive glass block panels with two
coats of bituminous paint.
(b) Providing and filling jambs and head of panels with expansion strips, joint filler
and sealant.
(c) Providing and fixing expanded metal reinforcement, galvanized, weighting not less
than 1.6 kg/m including securing to structure using proprietary fixing components.
(d) Bedding and pointing in cement/lime mortar.
(e) Supply and installation of glass block panels with panel anchors in accordance
with the manufacturer's instructions.
Rates for fire SC14.14 The rates for fire resisting glass block panels shall further include for :-
resisting glass
block panels (a) Supply and installation of glass block panels with panel anchors in accordance
with the manufacturer's instructions and in compliance with statutory requirements.
(b) Painting all sides of structural opening to receive glass block panels with two
coats of bituminous paint, if required.
(c) Providing and filling jambs and head of panels with expansion strips, joint filler
and sealant of fire resisting type.
(d) Providing and fixing reinforcement including securing to structure using proprietary
fixing components.
(e) Bedding and pointing in proprietary screeds and sealant of fire resisting type.
(f) Submission of test certificates and manufacturer's guarantee.
Rates for SC14.15 The rates for window and door films shall include for : -
window and
door films (a) Films of minimum nominal thickness of polyester of 0.08 mm pigmented to
provide black or other colour as required by the Maintenance Surveyor.
(b) Cleaning of bonding surface and coating with a solvent based adhesive prior to
applying films.
(c) Providing technical information, test certificate and manufacturer's guarantee as
required by the Maintenance Surveyor for approval or as stated in the Contract.
Glass block SC14.16 G.S. clauses for glass block panels can be found in the Brickwork and Blockwork Section
panels of the General Specification for Building.
14/4
14 GLAZING 14
Item Item
GENERAL GLAZING Wired
Figure Wired
Reeded polished
Clear float glass rolled Rough cast glass cast
Glass glazing sheet : - glass plate
glass glass
glass
Thickness (mm) 3 4 5 6 3 3 5 6 6 6
A B C D E F G H I J
Per square metre $ $ $ $ $ $ $ $ $ $
14001 Glass and glazing to wood with putty or
to metal with glazing compound................................... 97.30 105.60 124.20 146.60 111.50 124.50 134.40 168.90 233.20 353.20 14001
14002 Ditto but with wood or metal beads.............................. 123.50 132.20 157.50 185.00 138.50 151.50 159.80 195.60 283.80 429.80 14002
14003 Add to either of Items 14001 to 14002
inclusive if glass, when fixed, is in single
pane exceeding 5 m...................................................... 9.90 10.80 12.40 14.70 9.60 11.30 13.70 16.10 37.70 35.30 14003
14004 Take out and clear away serviceable
glass glazed to wood with putty or to
metal with glazing compound....................................... 21.70 23.60 25.50 27.40 21.70 21.70 25.50 27.40 27.40 27.40 14004
14005 Ditto but with wood or metal beads.............................. 25.50 27.40 29.30 31.90 25.50 25.50 29.30 31.90 31.90 31.90 14005
14006 Take out and set aside for re-use
serviceable glass glazed to wood with putty
or to metal with glazing compound............................... 26.20 28.10 31.30 32.50 26.20 26.20 31.30 32.50 32.50 32.50 14006
14007 Ditto but with wood or metal beads.............................. 33.80 36.40 38.90 42.10 33.80 33.80 38.90 42.10 42.10 42.10 14007
14008 Glazing only to wood with putty or to
metal with glazing compound....................................... 22.40 24.40 26.30 29.30 22.40 22.40 26.30 29.30 29.30 29.30 14008
14009 Ditto but with wood or metal beads.............................. 40.00 41.90 42.90 44.90 40.00 40.00 42.90 44.90 44.90 44.90 14009
14010 Add to either of Items 14001 to 14009
inclusive if glazing to fixed sash in
position behind guard bars............................................ 11.70 11.70 11.70 11.70 11.70 11.70 11.70 11.70 11.70 11.70 14010
Per linear metre
14011 Straight cutting............................................................... 2.90 3.90 3.90 3.90 2.90 2.90 2.90 3.90 4.90 4.90 14011
14012 Circular cutting.............................................................. 3.90 3.90 4.90 4.90 3.90 3.90 4.90 4.90 7.80 7.80 14012
Each
14013 Cutting hole with straight sides n.e. 0.20 m
through pane of glass..................................................... 12.70 13.70 14.60 15.60 12.70 12.70 14.60 15.60 23.40 23.40 14013
14014 Cutting circular or elliptical hole of n.e. 0.20 m
through pane of glass..................................................... 19.50 20.50 22.40 23.40 19.50 19.50 22.40 23.40 35.10 35.10 14014
14/5
14 GLAZING 14
Item Item
GENERAL GLAZING (CONT'D)
Glass glazing sheet : - (Cont'd) Float plate glass Reflec-
Tinted glass in any colour Obscure glass
(Polished plate or float) tive glass
Thickness (mm) 5 6 10 12 6 10 12 6 5 6
A B C D E F G H I J
Per square metre $ $ $ $ $ $ $ $ $ $
14015 Glass and glazing to wood with putty or
to metal with glazing compound................................... 174.20 201.50 340.90 417.40 223.80 380.50 447.70 317.10 137.10 171.40 14015
14016 Ditto but with wood or metal beads.............................. 206.50 233.30 380.10 458.80 255.20 418.60 488.00 339.40 161.80 200.50 14016
.
14017 Add to either of Items 14015 to 14016
inclusive if glass, when fixed, is in
single pane exceeding 5 m........................................... 14.40 16.10 25.80 32.10 31.30 57.10 67.20 50.80 16.10 18.80 14017
14018 Take out and clear away serviceable glass
glazed to wood with putty or to metal
with glazing compound................................................. 25.50 27.40 31.90 35.70 23.60 28.10 31.30 25.50 23.60 24.90 14018
14019 Ditto but with wood or metal beads.............................. 29.30 31.90 36.40 40.80 26.80 33.20 37.00 28.10 23.60 28.70 14019
14020 Take out and set aside for re-use
serviceable glass glazed to wood with putty
or to metal with glazing compound............................... 31.30 32.50 38.30 42.70 30.00 37.60 42.70 31.30 28.70 31.30 14020
14021 Ditto but with wood or metal beads.............................. 38.90 42.10 48.50 53.60 38.90 46.60 54.20 39.60 37.60 40.80 14021
14022 Glazing only to wood with putty or
to metal with glazing compound................................... 26.30 29.30 34.10 38.00 28.30 34.10 39.00 29.30 27.30 30.20 14022
14023 Ditto but with wood or metal beads.............................. 42.90 44.90 50.70 54.60 44.90 54.60 60.50 45.80 44.90 47.80 14023
14024 Add to either of Items 14015 to 14023
inclusive if glazing to fixed sash in
position behind guard bars............................................ 11.70 11.70 11.70 11.70 11.70 11.70 11.70 11.70 11.70 11.70 14024
Per linear metre
14025 Straight cutting............................................................... 2.90 3.90 3.90 3.90 3.90 4.90 5.90 3.90 3.90 3.90 14025
14026 Circular cutting.............................................................. 4.90 4.90 5.90 5.90 5.90 6.80 7.80 5.90 5.90 5.90 14026
Each
14027 Cutting hole with straight sides
n.e. 0.20 m through pane of glass................................. 14.60 15.60 19.50 21.50 15.60 19.50 21.50 16.60 15.60 16.60 14027
14028 Cutting circular or elliptical hole
n.e. 0.20 m through pane of glass................................. 22.40 23.40 29.30 31.20 23.40 29.30 31.20 24.40 23.40 24.40 14028
14/6
14 GLAZING 14
Item Item
GENERAL GLAZING (CONT'D)
Polycarbonate glazing sheet : - Polycarbonate glazing sheet
Thickness (mm) 2 3 5 6 10 12
A B C D E F
Per square metre $ $ $ $ $ $
14029 Polycarbonate glazing sheet glazed to wood with putty or to metal with
glazing compound................................................................................................................................. 300.30 428.90 561.30 714.80 1,217.10 1,338.80 14029
14030 Ditto but with wood or metal beads...................................................................................................... 318.30 520.20 578.70 736.20 1,241.40 1,365.60 14030
14031 Polycarbonate glazing sheet fixed to wood or metal frames
(measured separately) with screws........................................................................................................ 297.30 490.50 556.20 707.60 1,134.30 1,325.40 14031
14032 Add to either of Items 14029 to 14031 inclusive for coloured polycarbonate
sheet....................................................................................................................................................... 84.10 93.10 129.70 150.10 192.30 214.00 14032
14033 Add to either of Items 14029 to 14031 inclusive for polycarbonate sheet, when
fixed, is in single pane exceeding 5 m................................................................................................. 24.30 39.60 48.80 62.90 103.50 111.10 14033
14034 Add to either of Items 14029 to 14031 inclusive for polycarbonate with surface
hardened treatment sheet....................................................................................................................... 151.00 178.40 190.30 233.00 286.00 311.70 14034
14035 Take out and clear away polycarbonate glazing sheet glazed to wood with
putty or to metal with glazing compound............................................................................................. 19.80 20.40 22.30 24.20 27.40 28.10 14035
14036 Ditto but with wood or metal beads...................................................................................................... 22.30 23.60 26.80 28.70 33.20 37.60 14036
14037 Take out and set aside for re-use polycarbonate glazing sheet glazed to
wood with putty or to metal with glazing compound........................................................................... 24.20 25.50 30.60 31.30 38.90 42.10 14037
14038 Ditto but with wood or metal beads...................................................................................................... 31.30 35.10 38.90 39.60 49.80 51.70 14038
14039 Take down and clear away polycarbonate sheet fixed to wood or metal
frames with screws................................................................................................................................ 22.30 23.60 26.80 28.70 33.20 37.60 14039
14040 Take out and set aside for re-use polycarbonate sheet fixed to wood or
metal frames with screws...................................................................................................................... 24.20 25.50 30.60 30.60 38.90 42.10 14040
14041 Glazing only to wood with putty or to metal with glazing compound................................................. 63.40 64.40 69.20 71.20 75.10 76.10 14041
14042 Ditto but with wood or metal beads...................................................................................................... 44.90 45.80 50.70 51.70 61.40 63.40 14042
14043 Fix only polycarbonate sheet to wood or metal frames with self-tapping
screws or hooks..................................................................................................................................... 31.30 31.90 37.00 37.60 44.00 47.20 14043
Per linear metre
14044 Straight cutting...................................................................................................................................... 3.90 4.50 4.80 5.20 6.70 7.20 14044
14045 Circular cutting...................................................................................................................................... 5.90 6.60 6.80 7.30 9.10 9.80 14045
14/7
14 GLAZING 14
Item Item
GENERAL GLAZING (CONT'D)
Polycarbonate glazing sheet : - (Cont'd) Polycarbonate glazing sheet
Thickness (mm) 2 3 5 6 10 12
A B C D E F
Each $ $ $ $ $ $
14046 Cutting hole with straight sides n.e. 0.20 m through
pane of polycarbonate............................................................................................................................ 12.70 14.60 16.60 17.60 22.40 24.40 14046
14047 Cutting circular or elliptical hole n.e. 0.20 m through
pane of polycarbonate............................................................................................................................ 20.50 22.40 24.40 25.40 32.20 34.10 14047
14048 Forming speak hole perforations of diameter n.e. 10 mm through
polycarbonate sheet over an area of overall size n.e. 0.20 m.............................................................. 19.50 21.50 23.40 24.40 30.20 33.20 14048
Clear float heat strengthened glass 19 mm thick : -
A
Per square metre $
14049 Glass and glazing to wood with putty or to metal with glazing compound................................................................................................................................... 810.00 14049
14050 Ditto but with wood or metal beads................................................................................................................................................................................................ 834.30 14050
14051 Add to either of Items 14049 to 14050 inclusive if glass, when fixed, is in single pane exceeding 5 m and not exceeding 30 m........................................... 136.10 14051
14052 Add to either of Items 14049 to 14050 inclusive if glass, when fixed, is in single pane exceeding 30 m.................................................................................. 130.40 14052
14053 Take out and clear away serviceable glass glazed to wood with putty or to metal with glazing compound................................................................................ 34.40 14053
14054 Ditto but with wood or metal beads................................................................................................................................................................................................ 40.80 14054
14055 Take out and set aside for re-use serviceable glass glazed to wood with putty or to metal with
glazing compound........................................................................................................................................................................................................................... 52.90 14055
14056 Ditto but with wood or metal beads................................................................................................................................................................................................ 62.50 14056
14057 Glazing only to wood with putty or to metal with glazing compound........................................................................................................................................... 57.50 14057
14058 Ditto but with wood or metal beads................................................................................................................................................................................................ 75.10 14058
14059 Add to either of Items 14049 to 14058 inclusive if glazing to fixed sash in position behind guard bars.................................................................................... 11.70 14059
Per linear metre
14060 Straight cutting................................................................................................................................................................................................................................ 6.80 14060
14061 Circular cutting................................................................................................................................................................................................................................ 10.70 14061
Each
14062 Cutting holes with straight sides n.e. 0.20 m through pane of glass............................................................................................................................................ 29.30 14062
14063 Cutting circular or elliptical holes n.e. 0.20 m through pane of glass.......................................................................................................................................... 39.00 14063
14/8
14 GLAZING 14
Item Item
GENERAL GLAZING (CONT'D)
Thickness (mm)
Fully tempered glass : 6 10 12 19
A B C D
Per square metre $ $ $ $
14064 Glass and glazing to wood with putty or to metal with glazing compound............................................................................. 318.30 413.90 455.00 818.30 14064
14065 Ditto but with wood or metal beads.......................................................................................................................................... 353.40 447.10 491.40 842.90 14065
14066 Add to either of Items 14064 to 14065 inclusive if glass, when fixed, is in single pane exceeding
5 m and not exceeding 30 m................................................................................................................................................... 53.50 69.60 76.40 137.50 14066
14067 Add to either of Items 14064 to 14065 inclusive if glass, when fixed, is in single pane exceeding 30 m............................ 51.30 66.70 73.30 131.80 14067
14068 Take out and clear away serviceable glass glazed to wood with putty or to metal with glazing compound.......................... 23.60 26.80 31.90 34.40 14068
14069 Ditto but with wood or metal beads.......................................................................................................................................... 27.40 31.90 38.30 40.80 14069
14070 Take out and set aside for re-use serviceable glass glazed to wood with putty or to metal with
glazing compound..................................................................................................................................................................... 29.30 37.60 41.50 52.90 14070
14071 Ditto but with wood or metal beads.......................................................................................................................................... 38.30 47.80 53.60 62.50 14071
14072 Glazing only to wood with putty or to metal with glazing compound..................................................................................... 28.30 34.10 38.00 57.50 14072
14073 Ditto but with wood or metal beads.......................................................................................................................................... 44.90 52.70 59.50 75.10 14073
14074 Add to either of Items 14064 to 14073 inclusive if glazing to fixed sash in position behind guard bars............................... 11.70 11.70 11.70 11.70 14074
Per linear metre
14075 Straight cutting.......................................................................................................................................................................... 3.90 4.90 5.90 7.80 14075
14076 Circular cutting.......................................................................................................................................................................... 5.90 6.80 7.80 10.70 14076
Each
14077 Cutting holes with straight sides n.e. 0.20 m through pane of glass....................................................................................... 16.60 21.50 23.40 29.30 14077
14078 Cutting circular or elliptical holes n.e. 0.20 m through pane of glass.................................................................................... 24.40 31.20 33.20 39.00 14078
14/9
14 GLAZING 14
Item Item
GLASS LOUVRE BLADES Clear
Rough Wired Wired plate
Clear float glass cast cast polished glass
Glass louvre blades with ground and arrived edges glass glass plate (polish-
and fixing to slots in frames or adjustable louvre glass ed plate
metal clips (slots or clips measured separately) : - or float)
Thickness (mm) 4 5 6 6 6 6 6
A B C D E F G
Per linear metre $ $ $ $ $ $ $
14079 Blade 75 mm wide............................................................................................................... 24.00 27.00 28.40 31.50 48.90 68.20 36.20 14079
14080 Ditto 100 mm wide.............................................................................................................. 25.20 28.30 29.80 33.00 51.30 71.60 38.00 14080
14081 Ditto 150 mm wide.............................................................................................................. 27.60 32.40 34.10 37.80 58.60 81.80 43.40 14081
14082 Take out and set aside for re-use blade 75 mm wide
including risk and making good breakages......................................................................... 1.90 1.90 1.90 1.90 1.90 1.90 1.90 14082
14083 Ditto 100 mm wide.............................................................................................................. 1.90 1.90 1.90 1.90 1.90 1.90 1.90 14083
14084 Ditto 150 mm wide.............................................................................................................. 1.90 1.90 1.90 1.90 1.90 1.90 1.90 14084
A
Each $
14085 Fix only louvre blades of any length, width or thickness in slot or clip (measured separately).................................................................................................... 3.20 14085
14086 Take out and clear away broken or serviceable louvre blade of any length, width or thickness in slot or clip............................................................................ 1.30 14086
POLYCARBONATE SHEET Double layer "Cellular Type" clear UV protection polycarbonate sheet
Thickness (mm) overall 4 4.5 6 8 10 16 20 30
Approx. weight g/m2 800 1000 1300 1500 1700 2700 3100 3500
Light transmission % 88 88 88 88 88 82 79 82
U-value W/m2K 3.9 3.9 3.7 3.4 3.2 2.9 2.8 2.6
Falling dare Gardiner
21.3 21.3 >27 >27 >27 >27 >27 >27
impact at 23C Nm
A B C D E F G H
Per square metre $ $ $ $ $ $ $ $
14087 Polycarbonate sheet fixed to wood or metal frames
(measured separately) with screws or metal beads........................................... 138.50 146.00 175.80 203.10 229.20 287.40 339.20 448.30 14087
14088 Take down and clear away polycarbonate sheet fixed
to wood or metal frames with screws or metal beads....................................... 20.40 21.70 23.00 24.20 27.40 35.10 37.60 45.90 14088
14089 Take down and set aside for re-use polycarbonate
sheet fixed to wood or metal frames with screws or
metal beads........................................................................................................ 20.40 21.70 24.20 26.80 30.00 37.60 44.00 54.20 14089
14090 Fix only polycarbonate sheet fixed to wood or metal
frames with screws or metal beads.................................................................... 40.20 42.10 45.90 49.10 55.50 61.20 72.70 83.60 14090
14/10
14 GLAZING 14
Item Item
POLYCARBONATE SHEET (CONT'D) Triple layer
"Cellular Type"
clear UV protection
polycarbonate sheet
Thickness (mm) 16 20
Approx. weight g/m2 2700 3100
Light transmission % 82 79
U-value W/m2K 2.4 2.2
Falling dare Gardiner
>27 >27
impact at 23C Nm
A B
Per square metre $ $
14091 Polycarbonate sheet fixed to wood or metal frames (measured separately) with screws or metal beads................................................................... 228.70 527.00 14091
14092 Take down and clear away polycarbonate sheet fixed to wood or metal frames with screws or metal beads............................................................ 30.60 33.20 14092
14093 Take down and set aside for re-use polycarbonate sheet fixed to wood or metal frames with screws or metal beads............................................... 33.80 37.60 14093
14094 Fix only polycarbonate sheet fixed to wood or metal frames with screws or metal beads.......................................................................................... 54.20 61.90 14094
Add to either of Items 14087 and 14091 inclusive for bronze and opal white polycarbonate plastic sheet................................................................................. 5%
Add to either of Items 14087 and 14091 inclusive for coloured polycarbonate plastic other than bronze or opal white............................................................ 15%
LAMINATED GLASS Clear Colour
Float Tinted
Glass
A B
Per square metre $ $
14095 Supply and fix (6 mm float plate glass + 1.52 mm Pvb + 6 mm float plate glass) thick laminated glass and glazing to wood
with putty or to metal with silicon mastic sealant or other glazing compound and drilling holes through the glass ................................................ 636.90 675.50 14095
14096 Ditto but with wood or metal beads.............................................................................................................................................................................. 803.70 770.10 14096
14/11
14 GLAZING 14
Item Item
LAMINATED GLASS (CONT'D) Glass thickness (mm) 6+6 8+8 8+8 10 + 10 12 + 12
Pvb thickness (mm) 0.76 0.76 1.52 1.52 1.52
A B C D E
Per square metre $ $ $ $ $
14097 Supply and fix laminated float glass with Pvb inlay and glazing to wood with putty or to metal
with silicon mastic sealant or other glazing compound and drilling holes through the glass............................... 402.80 495.50 598.00 720.10 836.80 14097
14098 Ditto but with wood or metal beads........................................................................................................................ 508.30 625.30 754.60 908.80 1,056.10 14098
Glass thickness (mm) 6+6 8+8 10 + 10 12 + 12
Pvb thickness (mm) 1.52 1.52 1.52 1.52
A B C D
Per square metre $ $ $ $
14099 Supply and fix laminated clear tempered glass with Pvb inlay and heat soak test processes and glazing to
wood with putty or to metal with silicon mastic sealant or other glazing compound and drilling holes
through the glass........................................................................................................................................................................ 621.70 759.50 864.30 973.60 14099
14100 Ditto but with wood or metal beads.......................................................................................................................................... 784.50 958.40 1,090.70 1,228.60 14100
Add to either of Items 14095 to 14100 inclusive for tinted glass in any colour............................................................................................................................ 10%
Add to either of Items 14095 to 14100 inclusive for sheeting bent to curve to radius n.e. 3.00 m.............................................................................................. 20%
Add to either of Items 14095 to 14100 inclusive for sheeting bent to curve to radius 3.00 - 15.00 m......................................................................................... 10%
BULLET OR BLAST RESISTANT LAMINATED SAFETY GLASS Take Take
Supply down down Fix
and and and set only
Bullet or blast resistant laminated safety glass fixed in accordance with the manufacturer's instructions : - fix clear aside for
away re-use
A B C D
Per square metre $ $ $ $
14101 7.52 mm Thick bullet or blast resistant laminated safety glass................................................................................................ 2,458.10 33.30 49.50 101.20 14101
14/12
14 GLAZING 14
Item Item
FIRE RATED GLASS
(Note : - The following Items 14102 to 14105 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
Fire rated glass with fire insulation and integrity of the half-hour fire resistance period : - Sand-
Clear Tinted Temper-
blasted
glass glass ed glass
glass
A B C D
Per square metre $ $ $ $
14102 Glass and glazing to wood with putty or to metal with glazing compound............................................................................. 1,015.20 1,948.10 1,637.80 2,412.00 14102
14103 Ditto but with wood or metal beads.......................................................................................................................................... 1,129.90 2,168.20 1,822.80 2,684.60 14103
14104 Add to either of Items 14102 to 14103 inclusive if glass, when fixed, is in single pane
exceeding 5 m and not exceeding 30 m................................................................................................................................. 170.60 327.30 275.10 405.20 14104
14105 Add to either of Items 14102 to 14103 inclusive if glass, when fixed, is in single pane exceeding 30 m............................ 163.50 313.60 263.70 388.30 14105
14106 Take out and clear away serviceable glass glazed to wood with putty
or to metal with glazing compound........................................................................................................................................... 27.40 23.60 24.90 23.60 14106
14107 Ditto but with wood or metal beads.......................................................................................................................................... 31.90 26.80 28.70 27.40 14107
14108 Take out and set aside for re-use serviceable glass glazed to wood or metal with
glazing compound..................................................................................................................................................................... 32.50 30.00 31.30 29.30 14108
14109 Ditto but with wood or metal beads.......................................................................................................................................... 42.10 38.90 40.80 38.30 14109
14110 Glazing only to wood with putty or to metal with glazing compound..................................................................................... 76.50 76.50 76.50 76.50 14110
14111 Ditto but with wood or metal beads.......................................................................................................................................... 86.10 86.10 86.10 86.10 14111
14112 Add to either of Items 14102 to 14111 inclusive if glazing to fixed sash in position behind
guard bars.................................................................................................................................................................................. 16.00 16.00 16.00 16.00 14112
Per linear metre
14113 Straight cutting.......................................................................................................................................................................... 3.90 3.90 3.90 3.90 14113
14114 Circular cutting.......................................................................................................................................................................... 5.90 5.90 5.90 5.90 14114
Each
14115 Cutting hole with straight sides n.e. 0.20 m through pane of glass........................................................................................ 22.40 22.40 22.40 23.40 14115
14116 Cutting circular or elliptical hole n.e. 0.20 m through pane of glass...................................................................................... 32.20 32.20 32.20 33.20 14116
14/13
14 GLAZING 14
Item Item
FIRE RATED GLASS (CONT'D)
(Note : - The following Items 14117 to 14120 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
Fire rated glass with fire insulation and integrity of the one hour fire resistance period : - Sand-
Clear Tinted Temper-
blasted
glass glass ed glass
glass
A B C D
Per square metre $ $ $ $
14117 Glass and glazing to wood with putty or to metal with glazing compound............................................................................. 1,151.00 2,184.00 1,821.80 2,683.00 14117
14118 Ditto but with wood or metal beads.......................................................................................................................................... 1,281.10 2,430.70 2,027.60 2,986.20 14118
14119 Add to either of Items 14117 to 14118 inclusive if glass, when fixed, is in single pane
exceeding 5 m and not exceeding 30 m................................................................................................................................. 193.40 366.90 306.10 450.70 14119
14120 Add to either of Items 14117 to 14118 inclusive if glass, when fixed, is in single pane exceeding 30 m............................ 185.30 351.60 293.30 432.00 14120
14121 Take out and clear away serviceable glass glazed to wood with putty
or to metal with glazing compound........................................................................................................................................... 27.40 23.60 24.90 23.60 14121
14122 Ditto but with wood or metal beads.......................................................................................................................................... 31.90 26.80 28.70 27.40 14122
14123 Take out and set aside for re-use serviceable glass glazed to wood or metal with
glazing compound..................................................................................................................................................................... 32.50 30.00 31.30 29.30 14123
14124 Ditto but with wood or metal beads.......................................................................................................................................... 42.10 38.90 40.80 38.30 14124
14125 Glazing only to wood with putty or to metal with glazing compound..................................................................................... 86.10 86.10 86.10 86.10 14125
14126 Ditto but with wood or metal beads.......................................................................................................................................... 95.70 95.70 95.70 95.70 14126
14127 Add to either of Items 14117 to 14126 inclusive if glazing to fixed sash in position behind
guard bars.................................................................................................................................................................................. 19.10 19.10 19.10 19.10 14127
Per linear metre
14128 Straight cutting.......................................................................................................................................................................... 3.90 3.90 3.90 3.90 14128
14129 Circular cutting.......................................................................................................................................................................... 5.90 5.90 5.90 5.90 14129
Each
14130 Cutting hole with straight sides n.e. 0.20 m through pane of glass........................................................................................ 25.40 25.40 25.40 26.40 14130
14131 Cutting circular or elliptical hole n.e. 0.20 m through pane of glass...................................................................................... 35.10 35.10 35.10 36.10 14131
14/14
14 GLAZING 14
Item Item
SUNDRIES
A
Per square metre $
14132 Grind surface of sheet glass (any size)........................................................................................................................................................................................... 93.20 14132
14133 Hack out old broken glass (any type and thickness) from wood or metal sash glazed with putty, glazing compound or beads,
set aside beads for re-use if any, clean and prepare rebates for re-glazing (re-glazing measured separately).............................................................................. 38.60 14133
Per linear metre
14134 Grind and round edge of glass (any type and thickness)................................................................................................................................................................ 16.80 14134
14135 Bed edge of glass (any type and thickness) in and including strip of wash leather or approved felt or plastic............................................................................ 10.80 14135
Each
14136 Grind recess of any size in pane of glass (as for sliding doors to hatches).................................................................................................................................... 18.50 14136
Per linear metre
14137 Point and seal joint between glass and beads, window frames and the like with 3 x 3 mm silicon mastic
sealant.............................................................................................................................................................................................................................................. 2.80 14137
14138 Ditto but with 3 x 6 mm silicon mastic sealant.............................................................................................................................................................................. 3.70 14138
14139 Cut out existing sealant................................................................................................................................................................................................................... 4.50 14139
GLASS BLOCK PANELS
Hollow glass blocks size: 150 x 150 - 250 x 250 mm square and 80 - 120 mm thick in any pattern and colour and including
all special blocks at junctions, corners and the like bedded and jointed in cement/lime mortar and pointed both sides
with white cement or white cement/lime mortar : -
A
Per square metre $
14140 Glass block panel............................................................................................................................................................................................................................ 985.20 14140
14141 Take down and clear away glass block panel................................................................................................................................................................................. 29.60 14141
14142 Take down and set aside for re-use glass block panel.................................................................................................................................................................... 78.80 14142
14143 Lay only glass block panel.............................................................................................................................................................................................................. 128.10 14143
Each
14144 Cut out existing defective glass block in isolated patches n.e. 10 glass blocks, fill up, joint in and replace
with new glass block and make good (each glass block measured).............................................................................................................................................. 60.90 14144
14/15
14 GLAZING 14
Item Item
FIRE RESISTING GLASS BLOCK PANELS
Fire resisting hollow glass blocks size: 150 x 150 - 250 x 250 mm square and 80 - 120 mm thick in any Fire rated period
pattern and colour and including all special blocks at junctions, corners and the like bedded and jointed : - Hour 1 Hour 1 Hour
A B C
Per square metre $ $ $
14145 Fire resisting glass block panels.................................................................................................................................................................. 4,436.40 6,144.50 8,982.90 14145
14146 Take down and clear away fire resisting glass block panels including corner glass blocks..................................................................... 26.80 26.80 26.80 14146
14147 Take down and set aside for re-use fire resisting glass block panels including corner glass blocks........................................................ 72.70 72.70 72.70 14147
14148 Lay only fire resisting glass block panels including corner glass blocks................................................................................................... 195.00 324.70 324.70 14148
MIRRORS
Glass mirror silver backed and painted with two coats of shellac varnish after silvering, Take
Take
Supply down and
bevel edged, if required, and fixed with chromium plated clips or screws with chromium down and
and set aside Fix only
plated clip-on heads, including drilling mirror and screwing clips or screws to backing or clear
fix for
plugging and screwing the same to wall : - away
re-use
A B C D
Per square metre $ $ $ $
14149 6 mm Silvering quality polished plate glass mirror.................................................................................................................. 202.50 6.80 14.60 40.80 14149
Supply
and
fix
A
Each $
14150 600 mm (Minimum) diameter convex mirror including brackets, mounting poles, visors, bolts, screws and the like, and drilling or
cutting mortices in concrete or other surfaces, grouting and make good....................................................................................................................................... 908.60 14150
14151 6 mm Thick single side reflective mirror, size 2400 x 1500 mm fixed to wood or metal frames (measured separately) with screws
or metal beads.................................................................................................................................................................................................................................. 454.30 14151
14/16
14 GLAZING 14
Item Item
WINDOW AND DOOR FILMS Supply
and
fix
A
Per square metre $
14152 Approved clear polyester window film which removes destructive ultraviolet rays from sunlight complying with the
following :
Not Less than
Total solar energy rejected 57%
Visible light transmitted 35%
Shading coefficient 0.49
Interior reflection 12%
Exterior reflection 18%
Glare reduction 60%
UN blocked 99%
......................................................................................................................................................................................................................................................... 382.00 14152
14153 Approved tough, durable, tear- and penetration-resistant film which bonds to the windows for protection complying with
the following :
Shading coefficient 0.91
Visible light reflected 11%
Visible light transmitted 86%
Emissivity 0.87
U Value 1.09
Heat gain reduction 3%
Heat loss reduction 0%
Glare reduction 2%
UV blocked 98%
Safety and Security Pass the 400ft.ib. (538 Joule) impact level: tested according
to the Safety Glazing Standard ANSI Z97.1 and CPSC 16CFR
......................................................................................................................................................................................................................................................... 458.40 14153
14154 Ditto complying with the following :
Shading coefficient 0.92
Visible light reflected 11%
Visible light transmitted 87%
Emissivity 0.87
U Value 1.09
Heat gain reduction 2%
Heat loss reduction 0%
Glare reduction 1%
UV blocked 98%
Safety and Security Pass the 150ft.ib. (202 Joule) impact level : tested according
to the Safety Glazing Standard ANSI Z97.1 and CPSC 16CFR
......................................................................................................................................................................................................................................................... 397.30 14154
14/17
14 GLAZING 14
Item Item
WINDOW AND DOOR FILMS (CONT'D) Supply
and
fix
A
Per square metre $
14155 Approved transparent, infra-red reflective polyester film which can be bonded to glass surfaces complying with the following :
Total solar transmission 17%
Total solar absorption 35%
Visible light transmission 21%
Visible light reflectance 53%
Shading coefficient 0.30
Emissivity 0.68
Total solar energy rejection 74%
Glare reduction 76%
Total solar energy rejection 74%
Ultra violet rejection 99%
......................................................................................................................................................................................................................................................... 244.50 14155
14156 Ditto complying with the following :
Total solar transmission 22.7%
Total solar absorption 59.25%
Visible light transmission 16%
Visible light reflectance 13%
Shading coefficient 0.43
Emissivity 0.71
Total solar energy rejection 63%
Glare reduction 82%
Total solar energy rejection 63%
Ultra violet rejection 99%
......................................................................................................................................................................................................................................................... 244.50 14156
14157 Ditto complying with the following :
Total solar transmission 28%
Total solar absorption 54%
Visible light transmission 33%
Visible light reflectance 21%
Shading coefficient 0.50
Emissivity 0.87
Total solar energy rejection 57%
Glare reduction 63%
Total solar energy rejection 57%
Ultra violet rejection 99%
......................................................................................................................................................................................................................................................... 244.50 14157
14158 Ditto complying with the following :
Total solar transmission 82%
Total solar absorption 16%
Visible light transmission 87%
Visible light reflectance 11%
Shading coefficient 0.95
Emissivity 0.89
Total solar energy rejection 15%
Ultra violet rejection 99%
Safety Standard ANSIZ97-1 Unlimited (Section 5.1) applied to nominal 1/4 inch annealed glass
......................................................................................................................................................................................................................................................... 244.50 14158
14/18
14 GLAZING 14
Item Item
WINDOW AND DOOR FILMS (CONT'D) Supply
and
fix
A
Per square metre $
14159 Approved transparent, infra-red reflective polyester film which can be bonded to glass surfaces complying with the
following :
Total solar absorption 18%
Visible light transmission 85%
Visible light reflectance 13%
Shading coefficient 0.96
Emissivity 0.88
Total solar energy rejection 17%
Ultra violet rejection 99%
Safety Standard ANSIZ97-1 Unlimited (Section 5.1) applied to nominal
5/32 inch, 1/8 inch and 1/4 inch annealed glass
......................................................................................................................................................................................................................................................... 364.40 14159
A
Per square metre $
14160 Take down and clear away window and door films and safety and security films........................................................................................................................ 54.20 14160
14/19
Section 15
PAINTING
15 PAINTING 15
SECTION 15
PAINTING
SPECIAL CONDITIONS
Paints generally SC15.01 All paints in this Section shall comply with the Air Pollution Control Ordinance (Cap.
311), Air Pollution Control (Volatile Organic Compounds) Regulation (Cap. 311W)
and G.S. Item 21.90 whether the paint is a low VOC paint or not.
New surfaces SC15.02 Painting of any type shall only be measured as on new surfaces when a complete
and wall face, door, frame or other area is of new or previously undecorated materials, or
redecoration has been completely stripped of existing decoration. Where patches of new plaster
occur within an area of existing plaster or portions of paintwork has been stripped off
and stopped or portions only of metal or woodwork insert in repairs, the painting to
the complete area shall be measured as redecoration.
Surfaces SC15.03 Surfaces described as walls and soffits include all vertical, horizontal, sloping or
described as curved walls, columns, soffits of slabs, beams, cills and the like, of concrete, brick,
walls and clay or concrete block, mason, or smooth or rough plastered or rendered, or
soffits unplastered or unrendered surface of any type, regardless of texture or porosity.
Measurement SC15.04 All works shall be measured the net area as painted. No deduction shall be made
generally for voids not exceeding 0.50m.
Surfaces to be painted exceeding 300 mm wide or girth or pipework exceeding
300 mm nominal diameter shall be measured as general surfaces. Surfaces to be
painted not exceeding 300 mm wide or girth or pipework not exceeding 300 mm
nominal diameter shall be measured as surfaces to the girth/nominal diameter as stated.
Articles not exceeding 0.01 m each where not in conjunction with surrounding
painted work shall be measured separately. Articles exceeding 0.01 m shall be
measured as general surfaces.
Allowance shall be made for the measurements of walls and soffits for additional
area of moulded or carved work and the like.
Measurement SC15.05 Certain specific items shall be measured as follows : -
of certain
specific items Chinese roof tiling, corrugated or Measured flat overall. Girth on rolls,
profiled sheeting. corrugations or profiles and the like
shall be held to be included in the items.
Metal work - glazed windows and Measured flat overall on both sides.
door the like.
Opening edges and all surfaces of frames,
mullions, transoms, cills and the like
shall be held to be included in the items.
15/1
15 PAINTING 15
SPECIAL CONDITIONS
Measurement SC15.05 Metal work - mesh covered or Measured flat overall on both sides.
of certain (Cont'd) ornamental fencing, gates and
specific items the like. All surfaces of frames, posts,
(Cont'd) braces, rails, projection and the like
shall be held to be included in the
items.
Manhole covers and frames, Measured flat overall on both sides.
tree grilles, channel covers and
the like. All surfaces of frames and the like
should be held to be included in the
items.
Wood sashes, glazed wooden Measured flat overall on both sides.
doors, windows, partitions,
panels, decorating or grilled Opening edges and all surfaces of
panels and the like. frames, mullions, transoms, cills
and the like shall be held to be
included in the items.
Wire mesh or mosquito Measured flat on both sides for
gauge panels. individual construction.
Painting shall be deemed to be
included in the sashes, doors,
partitions or panels if it forms
part of the construction.
Jalousies, louvre panels and the Measured flat on both sides for
like. individual construction.
Painting shall be deemed to be
included in the sashes, doors,
partitions or panels if it forms part
of the construction.
Collapsible gates Measured flat overall on both sides.
All surfaces of frames, guide and
track shall be held to be included in
the item.
Nuts, bolts, locks, brackets, Measured separately if it is isolated
staples, knobs, access panels, from the surrounding work.
switch and cover plates and the
like less than 0.01 m each and Painting to nuts and bolts shall be
isolated lengths of pipe or rod deemed to be carried out after
less than 300 mm long fixing in position.
15/2
15 PAINTING 15
SPECIAL CONDITIONS
Measurement SC15.05 Railings and balustrades with Measured flat overall on both sides.
of certain (Cont'd) balusters less than 200 mm
specific items centres All surfaces of frames, posts, braces,
(Cont'd) rails and the like shall be held to be
included in the items.
All other railings and balustrades Measured in accordance with
aforesaid Special Conditions Clause
SC15.04.
Measurement SC15.06 Throughout this Section, rates for all types of painting shall include all kinds of
of stripping of preparatory work. No payment will be made for stripping of existing decoration
existing under any circumstances, with the following exceptions : -
decorative
material (a) Stripping of existing decorative material is specifically ordered by the
Maintenance Surveyor in writing and there will be no further decorative
material applied on the prepared surface.
(b) Stripping of existing decorative material due to compatibility problem, which
is specifically ordered by the Maintenance Surveyor in writing.
Stripping of existing decoration shall be measured the net area of existing decoration
to be stripped. No deduction shall be made for voids not exceeding 0.50 m.
Measurement SC15.07 Paper hanging shall be measured the net area covered. No deduction shall be
of paper made for voids not exceeding 0.50 m.
hanging
Measurement SC15.08 Writing of letters, numbers or Chinese characters shall include for all full stops and
of writing commas. No separate payment shall be made. All punctuation excluding full stops and
commas shall be treated as letters. Logos, features, symbols and the like shall be
measured as Chinese characters of the same size.
Rates for SC15.09 The rates for painting shall generally include for : -
painting
generally (a) The application of low Volatile Organic Compound (VOC) paint in
accordance with the manufacturer's recommendation.
(b) Execution of work either internally or externally and in any position at any
height.
(c) Working to flat, curved or sloping surfaces.
(d) All preparation work to surfaces as G.S. Items 21.45 and 21.48.
(e) Mixing and applying as G.S. Item 21.53.
(f) Multi-coloured work and cutting to line.
15/3
15 PAINTING 15
SPECIAL CONDITIONS
Rates for SC15.09 (g) Painting on associated beads, hinges and other fittings, brackets, bolts,
painting (Cont'd) nuts, lugs and the like (unless isolated from other paintwork which will
generally be measured separately).
(Cont'd)
(h) Painting all surfaces with an approved primer.
(i) All identification of pipelines as G.S. Item 21.78.
(j) Keeping adjacent surfaces clean and painting surfaces disturbed as G.S.
Item 21.44.
(k) Removing all articles of ironmongery, hardware and the like before
painting and replacing after painting has been completed.
(l) Rubbing down smooth with sand paper on hardened coatings before the
subsequent coating is applied.
(m) Painting sample panels.
(n) Touching up coated surfaces on completion.
(o) Protecting and cleaning as G.S. Item 21.43.
(p) Removing painted sample panels.
(q) Submission of technical literature, test certificates and manufacturer's
guarantee or warranty.
(r) On-site checking, quality tests and surveillance tests.
(s) All necessary tests as specified in the Specification.
Rates for SC15.10 The rates for paintwork on new surfaces shall further include for : -
paintwork on
new surfaces (a) All preparation work to new surfaces as G.S. Item 21.46.
Rates for SC15.11 The rates for paintwork on existing surfaces shall further include for : -
paintwork
on existing (a) All preparation work to existing surfaces as G.S. Items 21.48 and 21.49.
surfaces
Rates for SC15.12 The rates for painting metal windows and doors shall further include for : -
painting
metal windows (a) Painting opening edges and all surfaces of frames, mullions, transoms,
and doors cills, guard bars, glazing beads and the like.
(b) Sealing putty with primer and paint as required.
15/4
15 PAINTING 15
SPECIAL CONDITIONS
Rates for SC15.13 The rates for painting wire mesh, expanded metal mesh, chain link and the like in
painting gates, fencing, guards, door and partition panels, etc. shall further include for : -
wire mesh,
expanded metal (a) Painting edge framing, posts, braces, rails and the like.
mesh, chain
link and the
like in gates,
fencing, etc.
Rates for SC15.14 The rates for painting general surfaces of wood including wood panels and flush
painting doors, wood sashes, wood partitions, etc. shall further includes for : -
wood
(a) Painting opening edges, mouldings, glazing beads and the like.
Rates for SC15.15 The rates for painting jalousies, louvre panels in doors and the like shall further
painting include for : -
jalousies,
louvre panels, (a) Painting all frames, stiles, rails, edges, louvre blades and the like.
etc.
Rates for SC15.16 The rates for surface protection to structural steel shall further include for any
surface combination of the following where applicable : -
protection to
structural (a) All preparation work to new surfaces as G.S. Item 15.61.
steel
(b) All preparation work to existing surfaces as G.S. Item 15.62.
(c) Painting to all joints as G.S. Item 15.64.
(d) Making good damaged galvanized coating as G.S. Item 15.63.
Rates for SC15.17 The rates for intumescent paint to structural steel surfaces shall further include for : -
intumescent
paint to (a) All preparation work to existing surfaces as recommended by the
structural steel manufacturer.
surfaces
(b) Application by an approved applicator including submission of method
statement and provision of a warranty for the period as required by the
Maintenance Surveyor or as stated in the Contract.
15/5
15 PAINTING 15
SPECIAL CONDITIONS
Rates for SC15.18 The rates for proprietary floor coating system shall further include for : -
proprietary
floor (a) All preparation work to existing surfaces as recommended by the manufacturer.
coating
system (b) Repairing minor cracks and voids to the substrate with approved
proprietary materials.
(c) Submission of method statement and provision of a warranty for the period
as required by the Maintenance Surveyor or as stated in the Contract.
Rates for SC15.19 The rates for proprietary paintwork system and line marking to existing or new sport
proprietary hall flooring system shall further include for : -
paintwork
system and line (a) All preparation work to existing surfaces or new surfaces as recommended
marking to by the manufacturer where required.
sport hall
flooring (b) Application by an approved applicator including submission of method
statement and provision of a warranty for the period as required by the
Maintenance Surveyor or as stated in the Contract, the warranty period of
which shall not be less than 2 years.
(c) Applying and obtaining accreditation / certification from recognized
international sports organizations when required.
Rates for SC15.20 The rates for stripping of existing decoration shall further include for : -
stripping of
existing decoration (a) Preparing surfaces as G.S. Item 21.48 after stripping the existing decoration.
Rates for SC15.21 The rates for road marking materials shall further include for : -
road marking
materials (a) All preparation work to new or existing surfaces as G.S. Item 21.71.
(b) Marking out to the required size and styles as ordered by the Maintenance
Surveyor.
(c) Executing work at specific time to avoid disturbance to public and traffic, and
provision of temporary lighting and traffic diversion arrangement when required.
(d) Testing of road marking materials, if required.
(e) Submission of samples and test certificate as G.S. Item 21.75.
Rates for SC15.22 The rates for painting lines, letters, characters, numbers, logos, symbols and the like
writing, line shall further include for : -
marking, etc.
(a) Marking out to the required size and styles.
(b) Setting out and paint all line marking to the required standards.
15/6
15 PAINTING 15
SPECIAL CONDITIONS
Rates for SC15.23 The rates for paper hanging shall further include for : -
paper
hanging (a) Execution of work internally and in any position at any height.
(b) Working to flat, curved or sloping surfaces.
(c) Preparing new or existing decorated surfaces.
(d) All necessary cleaning and preparation of substrate including applying skim
coat prior to hanging wall paper covering.
(e) All straight, raking or circular cutting.
(f) All cutting and waste and adhesive.
(g) Fixing in required pattern.
(h) Fixing and fitting around holes and openings, pipes, switches, brackets
and the like.
(i) Bonding to match existing works.
(j) Submission of samples and mock-up.
(k) Protecting and covering up.
Rates for SC15.24 The rates for proprietary paintwork system shall further include for : -
proprietary
paintwork (a) All preparation work to existing surfaces or new surfaces as recommended
system by the manufacturer where required.
(b) Application by an approved applicator including submission of method
statement and provision of a warranty for the period as required by the
Maintenance Surveyor or as stated in the Contract, the warranty period of
which shall not be less than 4 years.
Rates for SC15.25 The rates for re-enamel on bath tub shall include for : -
re-enamel
on bath tub (a) Cleaning and touch up existing surfaces of bath tub.
(b) Different colour of paint.
(c) Each bath tub ordered without any adjustment for minimum order.
(d) Protection of adjacent surfaces and make good all works damaged and
disturbed.
(e) The provision of a one-year warranty.
15/7
15 PAINTING 15
Item Item
LIMEWASH Internal External
New New
Redecoration Redecoration
Prepare and apply limewash to the following surfaces : - surfaces surfaces
Two One Two Two One Two
coats coat coats coats coat coats
A B C D E F
Per square metre $ $ $ $ $ $
15001 Walls and soffits.................................................................................................................................... 16.30 12.10 17.80 17.10 12.80 19.10 15001
15002 Profiled compressed particle sheeting.................................................................................................. 21.80 16.90 24.30 22.50 17.40 25.50 15002
EMULSION PAINT Internal External
New surfaces Redecoration New surfaces Redecoration
Water Water
Prepare and apply emulsion paint to the following surfaces : - One based One based
thinned lime thinned lime
coat resistant One Two coat resistant One Two
and primer full full and primer full full
two and coat coats two and coat coats
full two full two
coats full coats full
coats coats
A B C D E F G H
Per square metre $ $ $ $ $ $ $ $
15003 Walls and soffits................................................................................................ 38.80 42.90 18.50 30.00 40.40 44.70 20.30 32.90 15003
15004 Extra over Item 15003 for moulded enriched
surface picked out in one or more different
colours from general surface............................................................................. 16.10 17.00 7.60 12.90 19.20 19.80 7.70 13.40 15004
15005 Grille block wall of any thickness including
painting into recesses......................................................................................... 58.20 60.50 29.70 50.40 61.60 66.90 30.30 52.80 15005
15006 Soft or hard fibre board, insulating board,
acoustic tiles and similar surfaces..................................................................... 36.80 44.70 19.00 31.20 39.60 45.50 20.90 33.20 15006
15007 Profiled compressed particle sheeting............................................................... 53.20 60.30 25.50 38.90 56.40 61.00 28.80 40.50 15007
15/8
15 PAINTING 15
Item Item
ANTI-MOULD ACRYLIC EMULSION PAINT Internal External
New surfaces Redecoration New surfaces Redecoration
Water Water
Prepare and apply anti-mould acrylic emulsion paint to the One based One based
following surfaces : - thinned lime thinned lime
coat resistant One Two coat resistant One Two
and primer full full and primer full full
two and coat coats two and coat coats
full two full two
coats full coats full
coats coats
A B C D E F G H
Per square metre $ $ $ $ $ $ $ $
15008 Walls and soffits................................................................................................ 44.60 47.90 20.60 35.60 48.60 50.00 22.00 39.40 15008
15009 Extra over Item 15008 for moulded enriched
surface picked out in one or more different
colours from general surface ............................................................................ 13.50 16.40 5.80 9.70 15.20 18.00 6.90 12.00 15009
15010 Grille block wall of any thickness including
painting into recesses......................................................................................... 63.80 69.40 33.20 57.30 67.30 71.80 35.80 59.70 15010
15011 Soft or hard fibre board, insulating board,
acoustic tiles and similar surfaces .................................................................... 42.40 46.50 24.00 37.10 43.60 48.10 24.30 38.80 15011
15012 Profiled compressed particle sheeting............................................................... 55.60 59.10 27.80 49.80 58.70 62.80 29.50 51.80 15012
TEXTURED EMULSION PAINT Internal External
New surfaces Redecoration New surfaces Redecoration
Prepare and apply textured emulsion paint on the Water Water
following surfaces : - One based One based
thinned lime thinned lime
coat resistant One Two coat resistant One Two
and primer full full and primer full full
two and coat coats two and coat coats
full two full two
coats full coats full
coats coats
A B C D E F G H
Per square metre $ $ $ $ $ $ $ $
15013 Walls and soffits................................................................................................ 37.10 38.90 19.00 31.30 40.10 42.90 20.40 33.80 15013
15014 Grille block wall of any thickness including
painting into recesses......................................................................................... 57.30 62.60 27.20 46.60 60.30 64.70 28.60 47.20 15014
15015 Profiled compressed particle sheeting............................................................... 46.40 49.20 23.70 38.60 49.80 51.70 25.90 41.10 15015
15/9
15 PAINTING 15
Item Item
CEMENT PAINT Internal External
New New
Redecoration Redecoration
Prepare and apply cement paint on the following surfaces : - surfaces surfaces
Two One Two Two One Two
coats coat coats coats coat coats
A B C D E F
Per square metre $ $ $ $ $ $
15016 Walls and soffits.................................................................................................................................... 29.70 19.60 33.90 31.60 20.90 35.90 15016
15017 Grille block wall of any thickness including painting into recesses.................................................... 51.10 31.60 57.20 52.60 32.70 58.30 15017
15018 Chinese roof tiling................................................................................................................................. 53.20 30.40 58.60 55.60 33.20 59.40 15018
EXTERNAL TEXTURED PAINT External
New
Redecoration
Prepare and apply external textured paint to the following surfaces : - surfaces
Two One Two
coats coat coats
A B C
Per square metre $ $ $
15019 Walls and soffits.......................................................................................................................................................................................... 42.30 27.70 47.70 15019
15020 Grille block wall of any thickness including painting into recesses.......................................................................................................... 72.70 46.90 79.10 15020
15021 Chinese roof tiling....................................................................................................................................................................................... 77.10 47.00 81.80 15021
15022 Profiled compressed particle sheeting........................................................................................................................................................ 63.50 39.70 68.10 15022
MULTI-COLOUR PAINT Internal External
New Redeco- New Redeco-
Prepare and apply multi-colour paint to the following surfaces by spraying : - surfaces ration surfaces ration
One coat One One coat One
primer, binder primer, binder
one coat one coat
binder and binder and
coat one coat one
and one finishing and one finishing
finishing coat finishing coat
coat coat
A B C D
Per square metre $ $ $ $
15023 Walls and soffits........................................................................................................................................................................ 76.70 65.80 79.30 67.40 15023
Per linear metre
15024 Surfaces n.e. 150 mm girth....................................................................................................................................................... 12.00 10.30 15.00 13.00 15024
15025 Ditto but 150 - 300 mm girth.................................................................................................................................................... 21.60 18.90 24.70 21.80 15025
15/10
15 PAINTING 15
Item Item
SYNTHETIC PAINT Internal External
New surfaces Redecoration New surfaces Redecoration
Prepare and apply synthetic paint to the following surfaces : - Alkali Alkali
resisting Sealer, One resisting Sealer, One
primer, one undercoat primer, one undercoat
one undercoat One and one undercoat One and
undercoat and one finishing one undercoat and one finishing one
and one finishing coat finishing and one finishing coat finishing
finishing coat coat finishing coat coat
coat coat
A B C D E F G H
Per square metre $ $ $ $ $ $ $ $
15026 Walls and soffits................................................................................................ 46.50 44.50 25.60 35.60 51.90 48.10 28.60 38.90 15026
15027 Soft or hard fibre board, insulating board,
acoustic tiles and similar surfaces..................................................................... 49.20 46.80 26.10 36.00 51.60 49.30 28.40 39.30 15027
15028 Profiled compressed particle sheeting............................................................... 62.80 61.60 31.60 49.90 65.60 63.40 33.40 51.40 15028
Per linear metre
15029 Surfaces n.e. 150 mm girth................................................................................ 4.20 4.10 2.20 3.50 6.70 6.40 3.30 5.10 15029
15030 Ditto but 150 - 300 mm girth............................................................................ 12.70 12.50 7.80 10.80 14.60 14.30 9.30 12.20 15030
POLYURETHANE PAINT Internal External
New New
Redecoration Redecoration
Prepare and apply polyurethane paint to the following surfaces : Surfaces Surfaces
One coat One coat
primer, primer,
one One one One
undercoat One undercoat undercoat One undercoat
and finishing and one and finishing and one
one coat finishing one coat finishing
finishing coat finishing coat
coat coat
A B C D E F
Per square metre $ $ $ $ $ $
15031 Walls and soffits.................................................................................................................................... 64.70 32.90 53.80 68.50 33.90 55.60 15031
15032 Grille block wall of any thickness including painting into recesses.................................................... 95.50 47.20 79.00 98.70 51.80 81.10 15032
15033 Profiled compressed particle sheeting.................................................................................................. 79.20 43.00 72.10 83.30 45.90 75.00 15033
15034 Concrete paving, kerb stones and the like............................................................................................ 58.10 32.10 47.80 60.20 33.60 50.70 15034
15/11
15 PAINTING 15
Item Item
COLD CURE EPOXY PAINT Internal External
New New
Redecoration Redecoration
Prepare and apply cold cure epoxy paint (coloured) to the following surfaces : surfaces surfaces
One One One One
undercoat One undercoat undercoat One undercoat
and one finishing and one and one finishing and one
finishing coat finishing finishing coat finishing
coat coat coat coat
A B C D E F
Per square metre $ $ $ $ $ $
15035 Walls and soffits.................................................................................................................................... 54.90 38.60 60.00 56.30 39.90 62.80 15035
15036 Grille block wall of any thickness including painting into recesses.................................................... 82.30 49.20 84.10 87.00 53.80 89.10 15036
15037 Profiled compressed particle sheeting.................................................................................................. 65.50 43.80 79.70 69.60 45.10 83.30 15037
Per linear metre
15038 Surfaces n.e. 150 mm girth.................................................................................................................... 4.20 3.30 5.00 4.30 3.50 5.40 15038
15039 Ditto but 150 - 300 mm girth................................................................................................................ 13.90 8.30 14.80 15.60 8.50 16.10 15039
GRANITE COATING
Internal External
Prepare and apply 2 mm thick spray granite coating system to the following surfaces : New Redecor- New Redecor-
surfaces ration surfaces ration
A B C D
Per square metre $ $ $ $
15040 Walls and soffits........................................................................................................................................................................ 216.10 231.60 228.90 227.40 15040
15041 Grille block wall of any thickness including painting into recesses........................................................................................ 268.80 304.80 287.00 313.30 15041
15042 Masonry walls............................................................................................................................................................................ 268.80 304.80 287.00 313.30 15042
WATER-BASED PAINT ON SLOPEWORK New
Redecoration
Surfaces
Prepare and spray water-based paint (any colour) to : One One
undercoat One undercoat
and one finishing and one
finishing coat finishing
coat coat
A B C
Per square metre $ $ $
15043 Sprayed concrete surfaces on slopes........................................................................................................................................................... 85.00 62.60 98.30 15043
15/12
15 PAINTING 15
Item Item
SYNTHETIC PAINT ON METAL WORK New surfaces Redecoration
Primer Primer, One
Prepare and apply synthetic paint to the following metal work : only two under-
(No sub- under- One coat
sequent coats finishing and
paint and one coat one
to be finishing finishing
applied) coat coat
A B C D
Per square metre $ $ $ $
15044 General surfaces........................................................................................................................................................................ 16.00 54.70 24.90 38.30 15044
15045 Glazed windows, doors and the like......................................................................................................................................... 16.30 73.70 34.50 53.10 15045
15046 Wire mesh, expanded metal mesh, chain link, railings, balustrades and the like.................................................................... 15.70 56.60 27.90 43.50 15046
15047 Surfaces of corrugated or profiled sheeting ............................................................................................................................. 20.20 62.90 28.10 41.60 15047
15048 Surfaces of collapsible gate....................................................................................................................................................... 23.50 103.60 43.10 68.30 15048
15049 Jalousies, louvre panels and the like with fixed or moveable louvres..................................................................................... 21.70 85.70 35.80 58.50 15049
Per linear metre
15050 Surfaces n.e. 150 mm girth....................................................................................................................................................... 2.80 8.30 4.50 6.40 15050
15051 Ditto but 150 - 300 mm girth.................................................................................................................................................... 5.20 16.30 7.80 12.00 15051
15052 Pipe n.e. 55 mm nominal diameter........................................................................................................................................... 3.70 9.90 4.50 7.40 15052
15053 Ditto but 55 - 110 mm nominal diameter................................................................................................................................. 6.50 28.90 12.00 18.90 15053
15054 Ditto but 110 - 300 mm nominal diameter............................................................................................................................... 12.80 48.70 20.00 32.10 15054
15055 Eaves gutter of any type, inside and outside n.e. 600 mm total girth, including cleaning
out and making good joints in red lead .................................................................................................................................... 43.50 73.40 51.40 58.90 15055
Each
15056 Small isolated article n.e. 0.01 m............................................................................................................................................. 2.80 3.60 2.90 3.20 15056
15057 W.C. cistern including brackets................................................................................................................................................ 10.00 34.10 12.00 19.70 15057
15058 Rainwater or waste head of any size, inside and outside, including cleaning out................................................................... 40.20 65.60 44.20 52.50 15058
15/13
15 PAINTING 15
Item Item
METALLIC PAINT ON METAL WORK New Surfaces Redecoration
Primer Primer, One Two
Prepare and apply metallic paint (bright or bronze finish) on the following metal work : only two under- under-
(No under- One coat coats
subse- coats finishing and and
quent and one coat one one
paint finishing finishing finishing
to be coat coat coat
applied)
A B C D E
Per square metre $ $ $ $ $
15059 General surfaces...................................................................................................................................................... 16.00 70.20 31.70 44.80 64.90 15059
15060 Glazed windows, doors and the like....................................................................................................................... 18.30 83.20 36.50 58.30 79.70 15060
15061 Wire mesh, expanded metal mesh, chain link, railings, balustrades and the like.................................................. 17.30 65.80 30.90 46.60 60.70 15061
15062 Surfaces of corrugated or profiled sheeting............................................................................................................ 21.90 78.40 38.50 52.30 69.20 15062
15063 Surfaces of collapsible gate..................................................................................................................................... 23.10 115.50 45.90 73.90 104.50 15063
15064 Jalousies, louvre panels and the like with fixed or moveable louvres................................................................... 22.10 94.10 41.70 63.50 87.20 15064
Per linear metre
15065 Surfaces n.e. 150 mm girth..................................................................................................................................... 2.40 8.90 3.90 6.70 8.50 15065
15066 Ditto but 150 - 300 mm girth.................................................................................................................................. 5.20 17.40 8.00 12.90 15.70 15066
15067 Pipe n.e. 55 mm nominal diameter......................................................................................................................... 3.20 11.00 4.60 7.80 10.70 15067
15068 Ditto but 55 - 110 mm nominal diameter............................................................................................................... 6.60 32.20 12.60 20.00 29.60 15068
15069 Ditto but 110 - 300 mm nominal diameter............................................................................................................. 13.00 57.20 23.80 38.90 50.30 15069
15070 Eaves gutter of any type, inside and outside n.e. 600 mm total girth, including
cleaning out and making good joints in red lead ................................................................................................... 40.50 76.90 51.70 67.80 74.50 15070
Each
15071 Small isolated article n.e. 0.01 m........................................................................................................................... 2.20 3.80 2.30 3.50 3.60 15071
15072 W.C. cistern including brackets.............................................................................................................................. 8.10 36.20 14.00 22.60 27.50 15072
15073 Rainwater or waste head of any size, inside and outside, including cleaning out................................................. 40.00 70.40 45.90 51.70 65.30 15073
15/14
15 PAINTING 15
Item Item
HEAT RESISTING PAINT ON METAL WORK New Surfaces Redecoration
Primer Primer, One Two
Prepare and apply heat resisting paint on the following metal work : only two under- under-
(No under- One coat coats
subse- coats finishing and and
quent and one coat one one
paint finishing finishing finishing
to be coat coat coat
applied)
A B C D E
Per square metre $ $ $ $ $
15074 General surfaces...................................................................................................................................................... 21.20 75.30 33.00 51.20 69.40 15074
Per linear metre
15075 Surfaces n.e. 150 mm girth..................................................................................................................................... 2.90 8.50 3.90 6.20 8.30 15075
15076 Ditto but 150 - 300 mm girth.................................................................................................................................. 5.80 21.10 8.40 13.00 17.40 15076
15077 Pipe n.e. 55 mm nominal diameter......................................................................................................................... 4.20 12.30 5.20 8.60 12.00 15077
15078 Ditto but 55 - 110 mm nominal diameter............................................................................................................... 8.60 36.00 14.30 23.40 31.60 15078
15079 Ditto but 110 - 300 mm nominal diameter............................................................................................................. 16.10 63.50 28.00 40.20 54.70 15079
Each
15080 Small isolated article n.e. 0.01 m........................................................................................................................... 1.60 4.40 1.70 2.90 4.00 15080
CHEMICAL RESISTING PAINT ON METAL WORK
Prepare and apply chemical resisting paint on the following metal work : -
Per square metre
15081 General surfaces...................................................................................................................................................... 23.20 77.70 33.00 51.20 69.40 15081
Per linear metre
15082 Surfaces n.e. 150 mm girth..................................................................................................................................... 2.90 8.70 3.90 6.20 8.30 15082
15083 Ditto but 150 - 300 mm girth.................................................................................................................................. 6.00 21.90 8.40 13.00 17.40 15083
15/15
15 PAINTING 15
Item Item
BLACK ENAMEL PAINT ON METAL WORK Redeco-
New surfaces
ration
Prepare and apply black enamel paint on the following metal work : - Primer
only
(No Primer
subse- and one One
quent coat coat
paint
to be
applied)
A B C
Per square metre $ $ $
15084 General surfaces.......................................................................................................................................................................................... 15.70 28.60 25.20 15084
Per linear metre
15085 Surfaces n.e. 150 mm girth......................................................................................................................................................................... 2.40 5.60 4.40 15085
15086 Ditto but 150 - 300 mm girth...................................................................................................................................................................... 4.50 9.50 7.50 15086
15087 Pipe n.e. 55 mm nominal diameter............................................................................................................................................................. 3.90 8.70 6.80 15087
15088 Ditto but 55 - 110 mm nominal diameter................................................................................................................................................... 8.50 18.20 11.90 15088
15089 Ditto but 110 - 300 mm nominal diameter................................................................................................................................................. 14.10 31.40 22.60 15089
Each
15090 Small isolated article n.e. 0.01 m............................................................................................................................................................... 1.00 2.30 1.70 15090
NON-TOXIC PAINT ON METAL WORK
Prepare and apply non-toxic paint on the following metal work : -
Per square metre
15091 General surfaces.......................................................................................................................................................................................... 15.40 58.70 54.70 15091
15092 Surfaces of corrugated or profiled sheeting................................................................................................................................................ 20.20 74.30 67.00 15092
Per linear metre
15093 Surfaces n.e. 150 mm girth......................................................................................................................................................................... 2.40 9.00 6.70 15093
15094 Ditto but 150 - 300 mm girth...................................................................................................................................................................... 5.40 15.90 12.90 15094
15095 Eaves gutter of any type, inside and outside n.e. 600 mm total girth, including cleaning out and
making good joints in approved non-toxic mastic ..................................................................................................................................... 42.60 73.20 61.80 15095
15/16
15 PAINTING 15
Item Item
POLYURETHANE PAINT ON METAL WORK New surfaces Redecoration
Primer Primer, One
Prepare and apply polyurethane paint (coloured) on the following metal work : - only one under-
(No under- One coat
subse- coat finishing and
quent and one coat one
paint finishing finishing
to be coat coat
applied)
A B C D
Per square metre $ $ $ $
15096 General surfaces........................................................................................................................................................................ 16.20 55.50 31.30 47.00 15096
15097 Glazed windows, doors and the like......................................................................................................................................... 17.30 67.10 46.20 59.10 15097
15098 Wire mesh, expanded metal mesh, chain link, railings, balustrades and the like.................................................................... 17.30 55.80 31.60 49.50 15098
Per linear metre
15099 Surfaces n.e. 150 mm girth....................................................................................................................................................... 2.70 7.10 4.50 6.00 15099
15100 Ditto but 150 - 300 mm girth.................................................................................................................................................... 5.70 15.90 8.60 12.90 15100
15101 Pipe n.e. 55 mm nominal diameter........................................................................................................................................... 3.90 10.50 7.00 10.40 15101
15102 Ditto but 55 - 110 mm nominal diameter................................................................................................................................. 7.50 33.90 13.50 24.90 15102
15103 Ditto but 110 - 300 mm nominal diameter............................................................................................................................... 13.00 47.30 32.30 40.40 15103
Each
15104 Small isolated article n.e. 0.01 m............................................................................................................................................. 1.20 3.80 1.90 3.20 15104
15/17
15 PAINTING 15
Item Item
COLD CURE EPOXY PAINT ON METAL WORK New surfaces Redecoration
Primer Primer, One
Prepare and apply cold cure epoxy paint (coloured) on the following metal work : - only one under-
(No under- One coat
subse- coat finishing and
quent and one coat one
paint finishing finishing
to be coat coat
applied)
A B C D
Per square metre $ $ $ $
15105 General surfaces........................................................................................................................................................................ 16.40 51.80 28.20 45.70 15105
15106 Glazed windows, doors and the like......................................................................................................................................... 17.50 59.70 33.00 52.70 15106
15107 Wire mesh, expanded metal mesh, chain link, railing, balustrades and the like..................................................................... 16.90 55.90 30.50 48.00 15107
Per linear metre
15108 Surfaces n.e. 150 mm girth....................................................................................................................................................... 2.80 7.70 3.90 5.80 15108
15109 Ditto but 150 - 300 mm girth.................................................................................................................................................... 6.50 14.90 7.90 12.30 15109
15110 Pipe n.e. 55 mm nominal diameter........................................................................................................................................... 3.90 10.50 6.80 7.90 15110
15111 Ditto but 55 - 110 mm nominal diameter................................................................................................................................. 7.70 25.40 16.70 21.30 15111
15112 Ditto but 110 - 300 mm nominal diameter............................................................................................................................... 12.50 40.90 20.70 35.10 15112
Each
15113 Small isolated article n.e. 0.01 m............................................................................................................................................. 1.00 3.70 1.90 3.20 15113
SURFACE PROTECTION TO STRUCTURAL STEEL
Prepare and apply surface protection on the following surfaces as Type A Type B Type C Type D Type E Type F Type G
G.S. Items 15.61 & 15.62 : -
A B C D E F G
Per square metre $ $ $ $ $ $ $
15114 Structural steel (new surfaces)............................................................................................ 60.30 70.70 160.80 141.20 203.70 51.00 50.70 15114
15115 Structural steel (redecoration)............................................................................................. 63.80 74.50 158.70 139.70 167.90 48.90 50.40 15115
(Note : - The above Items 15114 to 15115 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
15/18
15 PAINTING 15
Item Item
POWDER COATING ON METAL WORK
Prepare and apply epoxy or polyester or polyurethane resin based dry powder coating with dry film thickness
50 ~ 70 microns on metal surface, including surface preparation all in strict accordance with manufacturer's instructions : -
A
Per square metre $
15116 Powder coating on metal surfaces.................................................................................................................................................................................................. 99.80 15116
Per linear metre
15117 Surfaces n.e. 150 mm girth............................................................................................................................................................................................................. 14.70 15117
15118 Ditto but 150 - 300 mm girth.......................................................................................................................................................................................................... 27.70 15118
Each
15119 Small isolated article n.e. 0.01m.................................................................................................................................................................................................... 1.80 15119
(Note : - The above Items 15116 to 15119 inclusive will only be paid for, if ordered by Maintenance Surveyor in writing.)
FLUOROCARBON PVF2 COATING ON METAL WORK
Prepare and apply fluoropolymer resin based coating with dry film thickness 30 ~ 72 microns on metal surface, including
surface preparation all in strict accordance with manufacturer's instructions :
A
Per square metre $
15120 2 Coats system (dry film thickness 30 ~ 37 microns) comprising primer coat and top coat on metal surface............................................................................. 109.20 15120
15121 3 Coats system (dry film thickness 40 ~ 52 microns) comprising primer coat, top coat and clear coat on metal surface.......................................................... 142.10 15121
15122 4 Coats system (dry film thickness 60 ~ 72 microns) comprising primer coat, barrier coat, top coat and clear coat on metal surface...................................... 199.00 15122
(Note : - The above Items 15120 to 15122 inclusive will only be paid for, if ordered by Maintenance Surveyor in writing.)
FIRE RETARDANT PAINT
New Redeco-
Prepare and apply fire retardant paint as G.S. Item 21.14 :
surfaces ration
A B
Per square metre $ $
15123 Fabric surfaces............................................................................................................................................................................................................... 18.20 20.80 15123
15124 Wood surfaces............................................................................................................................................................................................................... 19.20 21.50 15124
15125 Metal surfaces............................................................................................................................................................................................................... 18.40 21.00 15125
15/19
15 PAINTING 15
Item Item
INTUMESCENT PAINT
Fire rated period
Prepare and apply fire rated intumescent paint on structural steel surfaces : -
1 hour 2 hours
A B
Per square metre $ $
15126 Structural steel general surfaces................................................................................................................................................................................... 276.50 436.80 15126
Per linear metre
15127 Structural steel surfaces not exceeding 150 mm girth.................................................................................................................................................. 56.60 61.30 15127
15128 Ditto but 150 - 300 mm girth........................................................................................................................................................................................ 72.40 103.00 15128
Each
15129 Structural steel small isolated article n.e. 0.01 m........................................................................................................................................................ 9.10 15.50 15129
(Note:- The above Items 15126 to 15129 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
BLACK BITUMASTIC PAINT
New surfaces Redecoration
Prepare and apply black bitumastic paint on the following surfaces : - One Two One Two
coat coats coat coats
A B C D
Per square metre $ $ $ $
15130 Concrete, brick, stone, plastered or rendered, or similarly finished walls and soffits............................................................. 18.40 29.50 23.10 35.80 15130
15131 General metal surfaces.............................................................................................................................................................. 19.00 31.10 24.70 36.80 15131
15132 General surface of concrete and fixing fillets under floor boarding........................................................................................ 21.40 36.40 25.30 39.00 15132
15133 Glazed metal windows, doors and the like............................................................................................................................... 27.20 44.10 30.90 48.80 15133
15134 Wire mesh, expanded metal mesh, chain link, railings, balustrades and the like.................................................................... 20.10 32.00 24.70 38.30 15134
15135 Surfaces of corrugated or profiled metal sheeting.................................................................................................................... 20.50 32.90 26.30 39.30 15135
15136 Metal manhole covers, channel covers, tree grilles and the like.............................................................................................. 18.60 31.20 24.60 38.30 15136
15/20
15 PAINTING 15
Item Item
BLACK BITUMASTIC PAINT (CONT'D)
New surfaces Redecoration
Prepare and apply black bitumastic paint on the following surfaces : (Cont'd) One Two One Two
coat coats coat coats
A B C D
Per linear metre $ $ $ $
15137 Surfaces of metal n.e. 150 mm girth......................................................................................................................................... 1.70 2.60 2.40 3.00 15137
15138 Ditto but 150 - 300 mm girth.................................................................................................................................................... 4.10 7.70 5.10 9.00 15138
15139 Pipe n.e. 55 mm nominal diameter........................................................................................................................................... 3.40 5.30 3.90 6.00 15139
15140 Ditto but 55 - 110 mm nominal diameter................................................................................................................................. 8.00 13.70 9.70 14.30 15140
15141 Ditto but 110 - 300 mm nominal diameter............................................................................................................................... 14.70 25.80 15.10 27.00 15141
15142 Eaves gutter of any type, inside and outside n.e. 600 mm total girth, including
cleaning out and making good joints in red lead ..................................................................................................................... 37.90 46.50 44.40 53.50 15142
Each
15143 Small isolated article n.e. 0.01 m............................................................................................................................................. 5.10 9.30 6.00 9.80 15143
15144 W.C. cistern including brackets................................................................................................................................................ 8.20 14.30 9.50 15.40 15144
15145 Rainwater or waste head of any size, inside and outside, including cleaning out................................................................... 37.80 46.40 41.90 49.70 15145
WOOD PRESERVATIVE ON WOOD WORK
New surfaces Redecoration
Prepare and apply wood preservative on the following wood work : - One Two One Two
coat coats coat coats
A B C D
Per square metre $ $ $ $
15146 General surfaces........................................................................................................................................................................ 8.10 14.90 10.70 15.80 15146
Per linear metre
15147 Surfaces n.e. 150 mm girth....................................................................................................................................................... 1.10 2.10 1.20 2.20 15147
15148 Ditto but 150 - 300 mm girth.................................................................................................................................................... 2.40 3.90 2.50 4.10 15148
15/21
15 PAINTING 15
Item Item
SYNTHETIC PAINT ON WOOD WORK New surfaces Redecoration
Primer Primer, Primer, One
Prepare and apply synthetic paint on the following wood work : - only one two under-
(No sub- under- under- One coat
sequent coat coats finishing and
paint and one and one coat one
to be finishing finishing finishing
applied) coat coat coat
A B C D E
Per square metre $ $ $ $ $
15149 General surfaces including doors and sashes......................................................................................................... 10.80 39.10 46.10 24.60 32.00 15149
15150 Jalousies, louvre panels and the like with fixed or moveable louvres................................................................... 16.50 62.60 88.30 41.70 54.60 15150
Per linear metre
15151 Surfaces n.e. 150 mm girth..................................................................................................................................... 2.10 5.30 7.20 2.90 3.60 15151
15152 Ditto but 150 - 300 mm girth.................................................................................................................................. 3.30 11.50 14.50 6.20 9.00 15152
Each
15153 Small isolated article n.e. 0.01 m........................................................................................................................... 0.80 2.90 3.90 1.60 2.60 15153
POLYURETHANE PAINT ON WOOD WORK New
Redecoration
surfaces
Prepare and apply polyurethane paint on the following wood work : - One One
under- under-
coat One coat Two
and finishing and finishing
one coat one coats
finishing finishing
coat coat
A B C D
Per square metre $ $ $ $
15154 General surfaces including doors and sashes........................................................................................................................... 42.20 31.50 48.10 51.70 15154
15155 Jalousies, louvre panels and the like with fixed or moveable louvres..................................................................................... 66.90 44.60 73.40 81.50 15155
Per linear metre
15156 Surfaces n.e. 150 mm girth....................................................................................................................................................... 4.90 3.40 5.50 6.30 15156
15157 Ditto but 150 - 300 mm girth.................................................................................................................................................... 10.70 8.00 12.10 13.20 15157
Each
15158 Small isolated article n.e. 0.01 m............................................................................................................................................. 1.90 1.60 2.50 2.90 15158
New Redeco-
surfaces ration
A B
Per square metre $ $
15159 Wood block, strip or parquet flooring........................................................................................................................................................................... 30.20 34.90 15159
15/22
15 PAINTING 15
Item Item
POLYURETHANE SEALER AND POLISH ON WOOD WORK New
Redecoration
surfaces
Prepare and apply polyurethane sealer and polish on the following wood work : - One
sealer
coat and One Two
two coat coats
finishing
coats
A B C
Per square metre $ $ $
15160 Wood block or wood strip flooring............................................................................................................................................................. 51.10 32.60 47.20 15160
WAX POLISH ON WOOD WORK
New surfaces Redecoration
Prepare and wax polish to approval on the following wood work : Two Three One Two
coats coats coat coats
A B C D
Per square metre $ $ $ $
15161 General surfaces........................................................................................................................................................................ - 45.30 22.30 34.50 15161
Per linear metre
15162 Surfaces n.e. 150 mm girth....................................................................................................................................................... - 3.70 1.90 2.90 15162
15163 Surfaces 150 - 300 mm girth..................................................................................................................................................... - 10.80 5.30 8.20 15163
Per square metre
15164 Surfaces of wood block or wood strip flooring........................................................................................................................ 19.20 - 12.50 20.40 15164
NATURAL OIL ON LANDSCAPE TIMBER New Redeco-
surfaces ration
Prepare and apply natural oil coating on the following wood work : - Three Two
coats coats
A B
Per square metre $ $
15165 General surfaces of landscape timber........................................................................................................................................................................... 80.30 54.60 15165
15/23
15 PAINTING 15
Item Item
LINSEED OIL ON WOOD WORK New Redeco-
surfaces ration
Prepare and apply linseed oil on the following wood work : - Three Two
coats coats
A B
Per square metre $ $
15166 General surfaces............................................................................................................................................................................................................ 40.30 31.30 15166
Per linear metre
15167 Surfaces n.e. 150 mm girth........................................................................................................................................................................................... 3.30 2.60 15167
15168 Surfaces 150 - 300 mm girth......................................................................................................................................................................................... 9.80 7.80 15168
STAIN, VARNISH
New surfaces Redecoration
AND LACQUER ON
WOOD WORK Cellu-
Stain Varnish lose Stain Varnish Cellulose lacquer
Prepare and apply and stain, lacquer
varnish and/or lacquer on Two Addit- Two Three Three Two Addit- One Two One Two
the following wood work : coats ional coats coats coats coats ional coat coats coat coats
one coat one coat
A B C D E F G H I J K
Per square metre $ $ $ $ $ $ $ $ $ $ $
15169 General surfaces including
doors and sashes ......................................... 21.30 8.50 28.40 37.40 44.80 26.10 8.50 24.40 30.20 26.40 33.80 15169
15170 Jalousies, louvre panels and the like
with fixed or movable louvres .................... 28.10 11.10 39.50 48.90 57.70 34.80 11.10 29.70 44.00 32.00 48.10 15170
Per linear metre
15171 Surfaces n.e. 150 mm girth ......................... 1.80 0.60 2.50 3.20 3.60 2.40 0.60 1.90 2.90 2.20 3.20 15171
15172 Ditto but 150 - 300 mm girth....................... 5.40 2.30 6.80 9.10 11.10 6.50 2.30 5.10 7.60 6.80 8.60 15172
Each
15173 Small isolated article not
exceeding 0.01 m ....................................... 1.50 1.30 1.60 1.80 1.90 1.50 1.50 1.40 1.60 1.40 1.60 15173
PESTICIDAL COATING
Prepare and apply pesticidal coating to the following surfaces : New Redeco-
surfaces ration
A B
Per square metre $ $
15174 General surfaces of plaster, render, concrete, brick, block, stone or wood.................................................................................................................. 25.90 30.30 15174
Per linear metre
15175 Ditto but in band n.e. 150 mm wide at joints, junctions, skirting tops and similar positions..................................................................................... 3.70 4.20 15175
15/24
15 PAINTING 15
Item Item
MARKING MATERIALS Mark
out Re-paint over
Oblit-
Prepare and paint the following lines, etc., in white or yellow thermoplastic road marking material and existing
erate
(Type A) as BS 3262:1989 on tarmac, concrete or other surfaces for roads, carriageways, car parks, paint
existing
paving and the like : - in two One Two
coats coat coats
A B C D
Per linear metre $ $ $ $
15176 Line n.e. 150 mm wide.............................................................................................................................................................. 13.50 7.50 13.80 3.80 15176
15177 Ditto but 150 - 300 mm wide.................................................................................................................................................... 26.50 14.60 27.40 7.40 15177
15178 Line n.e. 150 mm wide and circular on plan n.e. 15.00 m radius............................................................................................ 14.40 8.30 14.70 4.20 15178
15179 Ditto but 150 - 300 mm wide.................................................................................................................................................... 27.60 15.50 29.20 7.90 15179
Each
15180 Letter, number, Chinese character, logo, symbol and the like n.e. 75 mm high...................................................................... 8.80 6.10 9.40 2.50 15180
15181 Ditto but 75 - 150 mm high....................................................................................................................................................... 18.50 12.00 19.10 5.50 15181
15182 Ditto but 150 - 225 mm high..................................................................................................................................................... 25.40 16.40 26.50 8.30 15182
15183 Ditto but 225 - 300 mm high..................................................................................................................................................... 35.20 22.30 36.30 12.40 15183
15184 Ditto but 300 - 450 mm high..................................................................................................................................................... 49.20 31.00 51.80 19.40 15184
15185 Ditto but 450 - 600 mm high..................................................................................................................................................... 72.90 44.60 74.50 31.80 15185
15186 Ditto but 600 - 1,000 mm high.................................................................................................................................................. 97.60 66.20 112.60 47.50 15186
15187 Ditto but 1,000 - 2,000 mm high.............................................................................................................................................. 144.40 87.70 151.30 63.90 15187
15188 Arrow-head n.e. 150 mm long.................................................................................................................................................. 12.70 8.30 13.40 4.60 15188
15189 Ditto but 150 - 300 mm long..................................................................................................................................................... 19.10 12.30 19.80 7.60 15189
15190 Ditto but 300 - 450 mm long..................................................................................................................................................... 27.20 17.10 28.20 10.20 15190
15191 Ditto but 450 - 900 mm long..................................................................................................................................................... 43.40 26.60 46.00 14.90 15191
15192 Ditto but 900 - 1,350 mm long.................................................................................................................................................. 77.70 45.30 80.60 21.10 15192
15193 Ditto but 1,350 - 2,000 mm long............................................................................................................................................... 118.40 67.20 121.70 31.70 15193
15194 Ditto but 2,000 - 3,000 mm long............................................................................................................................................... 154.50 90.10 162.10 42.00 15194
15195 Arrow-head with left/right and straight 1,350 - 2,000 mm long.............................................................................................. 138.00 79.80 141.90 36.50 15195
15196 Ditto but 2,000 - 3,000 mm long............................................................................................................................................... 176.10 101.00 182.30 47.40 15196
15/25
15 PAINTING 15
Item Item
MARKING MATERIALS (CONT'D) Mark
out Re-paint over
Oblit-
Prepare and paint the following lines, etc., in white or yellow thermoplastic road marking material and existing
erate
(Type B) as BS 3262:1989 on tarmac, concrete or other surfaces for roads, carriageways, car parks, paint
existing
paving and the like : - in two One Two
coats coat coats
A B C D
Per linear metre $ $ $ $
15197 Line n.e. 150 mm wide.............................................................................................................................................................. 14.30 7.80 14.60 3.80 15197
15198 Ditto but 150 - 300 mm wide.................................................................................................................................................... 27.10 14.90 29.00 7.40 15198
15199 Line n.e. 150 mm wide and circular on plan n.e. 15.00 m....................................................................................................... 14.80 8.20 15.70 4.00 15199
15200 Ditto but 150 - 300 mm wide.................................................................................................................................................... 28.70 15.90 30.80 8.00 15200
Each
15201 Letter, number, Chinese character, logo, symbol & the like n.e. 75 mm high......................................................................... 9.00 6.10 9.40 2.50 15201
15202 Ditto but 75 - 150 mm high....................................................................................................................................................... 18.50 12.00 19.20 5.50 15202
15203 Ditto but 150 - 225 mm high..................................................................................................................................................... 25.60 16.10 26.80 8.30 15203
15204 Ditto but 225 - 300 mm high..................................................................................................................................................... 30.50 27.30 37.00 12.40 15204
15205 Ditto but 300 - 450 mm high..................................................................................................................................................... 49.70 32.40 52.30 19.40 15205
15206 Ditto but 450 - 600 mm high..................................................................................................................................................... 73.70 45.50 76.80 31.80 15206
15207 Ditto but 600 - 1,000 mm high.................................................................................................................................................. 111.30 67.80 114.20 47.50 15207
15208 Ditto but 1,000 - 2,000 mm high.............................................................................................................................................. 148.20 90.20 151.60 63.90 15208
15209 Arrow-head n.e. 150 mm long.................................................................................................................................................. 12.70 8.30 13.40 4.60 15209
15210 Ditto but 150 - 300 mm long..................................................................................................................................................... 19.30 12.40 20.00 7.60 15210
15211 Ditto but 300 - 450 mm long..................................................................................................................................................... 27.60 17.20 28.60 10.20 15211
15212 Ditto but 450 - 900 mm long..................................................................................................................................................... 44.20 26.70 46.70 14.90 15212
15213 Ditto but 900 - 1,350 mm long.................................................................................................................................................. 79.40 46.70 83.40 21.10 15213
15214 Ditto but 1,350 - 2,000 mm long............................................................................................................................................... 119.10 68.60 123.90 31.60 15214
15215 Ditto but 2,000 - 3,000 mm long............................................................................................................................................... 158.70 92.00 163.70 42.00 15215
15216 Arrow-head with left/right and straight 1,350 - 2,000 mm long.............................................................................................. 138.90 80.40 144.10 36.10 15216
15217 Ditto but 2,000 - 3,000 mm long............................................................................................................................................... 182.20 104.30 184.40 47.50 15217
15/26
15 PAINTING 15
Item Item
FLUORESCENT PAINT New
Redecoration
surfaces
Prepare and apply fluorescent paint of any colour ordered on the following surfaces : - Alkali
resisting
primer, One
one white flat
white flat One water or
water or finishing oil based
oil based coat undercoat
undercoat and one
and one finishing
finishing coat
coat
A B C
Per square metre $ $ $
15218 Concrete paving, kerb stones and the like.................................................................................................................................................. 49.80 30.80 41.20 15218
15219 Plastered or rendered vertical surfaces....................................................................................................................................................... 51.50 32.50 43.10 15219
REFLECTING PAINT New
Redecoration
surfaces
Prepare and apply reflecting paint on the following surfaces including applying a surface One
coating of fine grain reflective aggregate, applied at a rate of not less than 0.6 kg/m2 coat
while finishing coat is still wet : - One One alkali
finishing finishing resisting
coat of coat of primer,
white white one
synthetic synthetic finishing
paint paint coat of
with high with high white
gloss gloss synthetic
finish finish paint
with high
gloss
finish
A B C
Per square metre $ $ $
15220 Concrete paving, kerb stones and the like.................................................................................................................................................. 32.60 48.00 63.20 15220
15221 Plastered or rendered vertical surfaces....................................................................................................................................................... 33.80 48.80 65.10 15221
CHALKBOARD PAINT New Redecoration
surfaces
Prepare and apply chalkboard paint to the following surfaces : - Two One Two
coats coat coats
A B C
Per square metre $ $ $
15222 On surfaces of chalkboard paint................................................................................................................................................................. 26.60 16.10 27.90 15222
15/27
15 PAINTING 15
Item Item
PROPRIETARY PAINTWORK SYSTEM
(Note : - The following Items 15223 to 15246 inclusive will only be paid for, if ordered by Maintenance Surveyor in writing.)
Proprietary hygienic coating system containing finely dispersed Polytetrafluoroethylene (PTFE) Prepare and apply
comprising primer, one base coat and two top coats, complying with the following properties New Redeco-
in accordance with the manufacturer's recommendation : - surfaces ration
A B
Product properties $ $
Water based and ready to use surface coating
Easy to clean
Fungicidal and prevention of most common bacteria and micro-organisms
Resistance to chemical and weathering / climatic attack
Water and dust shedding abilities
Inter-coat adhesion
Environmental friendly, UV and yellowing resistance
Material characteristics
Density 1,08 -1,18
Application temperature (Includes substrate) 8 - 30 deg C
Maximum Relative Humidity 85%
Volume Solids ca 35%
Typical D.F.T. ca 40 microns per coat
Theoretical Coverage 8-10 square metres per litre
Biocide Approvals EPA No's. 10466-27 and 6922-19-10466
Flash Point Not applicable. Waterborne.
Contains biocide Yes
Micro-porous Yes
Colour range BS4800
Testing
EEC Food Safety Regulation Complies to EEC 43/93 standards (CCFRA)
BS 476 Part 7 Spread of Flame Class 1
BS 148 Part 6 Combustion Class 0
BS 148 Part 6 Impact Resistance Hammer test. Surface free from cracks and delamination.
ASTM D2486 Abrasion Resistance Coating intact after 8,000 oscillations
BS 3900E1 Flexibility 1/4 bend test. Coating intact, free from crazing.
BS 3900 G6 Bacterial Control Surface growth test. Surface free from growth.
Per square metre
15223 Proprietary hygienic coating system to tiled wall surfaces including tile filler........................................................................................................... 341.40 350.60 15223
15224 Ditto to plastered walls and soffits............................................................................................................................................................................... 297.70 308.90 15224
Proprietary hygienic coating system comprising water based primer using water dispersible organic polymers and water
soluble amine resin blended with mix of pigments and fillers, and water-based epoxy coating of water dispersible epoxy
resin combined with hydrophilic amin adducts, complying with the following properties in accordance with the
manufacturer's recommendation : -
Material characteristics and testing
Abrasion resistance ASTM D4060 70 mg loss per 1000 cycles
Bacteria resistance BS4618 Section 4.5 Excellent
Dry heat resistance ASTM D248 135 (275)
Humidity resistance BS3900 Part F2 Unaffected 5,000 hours exposure
Scratch resistance BS 3900 Part E2 No failure at 2.5 kg (5.5 lbs) load
Primer : Water vapour permeability ASTM D1653 2.767 x 10-5 perm. Cm
Epoxy coating : Water vapour permeability ASTM D1653 5.62 x 10-6 perm.cm
Per square metre
15225 Proprietary hygienic coating system to tiled wall surfaces including tile filler........................................................................................................... 131.10 136.70 15225
15/28
15 PAINTING 15
Item Item
PROPRIETARY PAINTWORK SYSTEM (CONT'D)
Proprietary acrylic coating system comprising acrylic emulsion resin sealer and acrylic resin water based topcoat, Prepare and apply
complying with the following properties in accordance with the manufacturer's recommendation : - New Redeco-
surfaces ration
Product properties A B
Alkali resistant $ $
Strong sealing and adhesion
Weathering resistant
Easy application
Material characteristics and testing for acrylic emulsion resin sealer
Condition in container There shall be no lumps, no separation and no coagulation
of the ingredients.
Hardness H : Pencil scratch value
Film appearance JIS K5400 Little difference from samples JIS K5400
Water resistance JIS K5400 Unchanged when immersed 96 hours in tap water
Alkali proof JIS K5400 Unchanged when immersed 48 hours in saturated solution
of calcium hydroxide
Water permeability JIS A6909 0.3; in accordance with Water Permeability Test B Method.
After still standing for 24 hours, calculated from the height
of water head in the measuring pipette
Adhesive strength : standard condition : 199.9 N/cm2
JIS A 6910 5.8 1988
Adhesive strength : immersion in water 203.9 N/cm2
JIS A 6910 5.8 1988
Permeability JIS A 6910: 5.10 1988 0.05 ml
Material characteristics and testing for acrylic resin water based topcoat
Condition in container When agitated, absent of lumps and evenly mixed
Graining () 30
Admixture Evenly mixed consistency
Drying time (h) 1 Hour at 20
Film appearance When observing the painted surface, the flatness shall
be good, and there shall be no graining, wrinkles, unevenness,
blisters, holes or peelings.
Flexibility After still standing for 7 days, it shall withstand the flexure
steer caused by a mandrel with 10mm diameter.
Cross cut test It shall be 25/25
Impact When dropping a 300 g weight from the height of 500 mm,
the impact film surface shall have no cracks or peelings.
Accelerated weathering The degree of change in colour is not so large when
compared it with the standard products.
Resistance to fungal growth to BS 3900 G6 : Rating 0, no fungal growth
Quantifying dirt collection ASTM D 3719-87 Total dirt : 96.99%
Imbedded dirt : 94.48%
Per square metre
15226 Proprietary acrylic coating system to tiled wall surface including tile filler............................................................................................................... 161.70 165.50 15226
15227 Ditto to plastered walls and soffits............................................................................................................................................................................... 115.80 120.60 15227
15/29
15 PAINTING 15
Item Item
PROPRIETARY PAINTWORK SYSTEM (CONT'D)
Proprietary polyurethane resin based textured coating system comprising sealer, base coat and topcoat, Prepare and apply
complying with the following properties in accordance with the manufacturer's recommendation : - New Redeco-
surfaces ration
Product properties A B
Cross-linked film with acrylic urethane resin $ $
Weather resistant
Dirt resistant
Mould, fungus, algae, etc. resistant
Material characteristics
Sealer Mixing ratio (wt %) pre-mixed
Coverage (kg/m2) 0.14 ~ 0.18
Base coat Mixing ratio (wt %) 100%
Water 0 ~ 5%
Coverage (kg/m2) 1.3 ~ 1.7
Topcoat Mixing ratio (wt %) 100%
Water 0 ~ 20%
Coverage (kg/m2) 0.30 ~ 0.35
Testing
Low temperature stability (-5oC) to
JIS 5660 No deterioration
Application properties to JIS 5660 No application difficulties when applied twice
Drying Time (20oC) to JIS 5660 2 hours or less
Drying Time (5oC) to JIS 5660 4 hours or less
Appearance of film to JIS 5660 Film has normal appearance
Opacity (white and tint) to JIS 5660 0.95 or more
Gloss to JIS 5660 70 or more
Water resistance to JIS 5660 More than 80% gloss retention after 96 hour immersion; no
abnormalities on film surface
Alkali resistance to JIS 5660 More than 65% gloss retention after 7 days immersion; no
abnormalities on film surface
Salt water resistance to JIS 5660 168 hours immersed in 3% sodium chloride solution
Wet scrub resistance to JIS 5660 Must pass 1,000 cycles
Humidity and cool-heat cycling More than 80% gloss retention; no abnormalities on film
resistance to JIS 5660 surface
Fungus and mould resistance to Based on JIS Z 2911
JIS Z 2911
Accelerated weather resistance to More than 60% gloss retention after 480 hours test; degree of
JIS 5660 chalking is 8 points or more;
negligible change in color when compared to sample;
Weather resistance to JIS 5660 Degree of chalking is 6 points or more under 12 months test;
no cracking, swelling, holes, blistering; negligible change in
color and gloss when compared to sample
Per square metre
15228 Proprietary polyurethane resin based textured coating system to tiled wall surfaces including tile filler.................................................................. 117.80 122.80 15228
15229 Ditto to plastered walls and soffits............................................................................................................................................................................... 71.70 75.90 15229
15/30
15 PAINTING 15
Item Item
PROPRIETARY PAINTWORK SYSTEM (CONT'D)
Proprietary vermiculite acoustic spray coating system of resin emulsion combined with lightweight vermiculite Prepare and apply
comprising primer coat and texture coat, complying with the following properties in accordance with the New Redeco-
manufacturer's recommendation : - surfaces ration
A B
Product properties $ $
Condensation resistant
Sound absorption
Strong adhesion
Alkali resistant
Lightweight and easy workability
Performs humidity control
Non-combustible
Fire and heat resistant
Material characteristics
Primer coat
Texture coat Mixing ratio 20 kg Colour coating and 66 litre aggregate
30 ~ 50% with water
Coverage 1.80 ~ 2.00 kg/m2
Finish Matt
Specific gravity 1.22 0.05
Drying time Surface dry 6 hours
(at 30) Hard dry 24 hours
Shelf life Up to 6 months if stored in tightly sealed containers
Solid content 44 3%
Viscosity 55 5 ps / 30
Testing
Tested to Result
Regulations
Clear type Coloured type
Alkali resistance JIS A 6906 Passed Passed There shall be free from
Method C cracking, blister and peeling
Anti-condensation JIS A 6906 0.34 g 0.36 g 0.25 g minimum
Humidity resistance JIS A 6906 Passed Passed There shall be free from
Method B cracking, blister and peeling.
Adhesive strength JIS A 6906 0.1 N/mm2 0.1 N/mm2 0.1 N/mm2 {1.0 kgf/cm2} min.
{1.0 kgf/cm } {1.0 kgf/cm2}
2
or no interfacial peeling (result:
inside of substrate damaged)
Bonding property JIS A 6906 Passed Passed Aggregate shall be free from
of aggregate peeling and scattering.
Incombustibility JIS A 6906 Passed Passed It shall the first grade in
incombustibility of surface
test.
Per square metre
15230 Proprietary vermiculite acoustic spray coating system to plastered walls and soffits................................................................................................. 102.70 110.50 15230
15/31
15 PAINTING 15
Item Item
PROPRIETARY PAINTWORK SYSTEM (CONT'D)
Proprietary elastic acrylic silicon resin colour coating system comprising sealer coat, textured base coat and Prepare and apply
textured pattern topcoat, complying with the following properties in accordance with the manufacturer's New Redeco-
recommendation : - surfaces ration
A B
Product properties $ $
Sealer Acrylic emulsion resin sealer
Alkali resistant
Sealing and adhesion on different substrates
Topcoat Dust and dirt resistant
Fungus, Mould and algae resistant
Vapour permeable coating
Preventive of water prevention, carbonation damage and salt damage
Weather resistant
Fast drying
Material characteristics
Sealer Mixing ratio (wt %) 100%
Water 0 ~ 20%
Coverage (kg/m2) 0.08 ~ 0.15
Roller tile finish SP tile finish Stipple finish
Base Mixing ratio (wt %) 100% 100% 100%
coat Water 2 ~ 4% Water 2 ~ 4% Water 2 ~ 4%
Coverage (kg/m2) 0.6 ~ 0.8 0.5 ~ 0.7 0.4 ~ 0.5
Topcoat Mixing ratio (wt %) 100% 100% 100%
Water 2 ~ 4% Water 2 ~ 4% Water 2 ~ 4%
Coverage (kg/m2) 0.6 ~ 0.8 0.5 ~ 0.7 0.4 ~ 0.5
Testing to JIS A 6909
Stability at low temperature There shall be no lump and separation and compacting
of ingredients.
Crack resistance No crack shall appear during drying process.
Adhesive strength - standard condition 198.0 N/cm2
Adhesive strength - after immersion in water 172.5 N/cm2
Heating and cooling resistance There shall be no peeling off, crack, swell, remarkable
discoloration, and gloss reduction.
Water permeability 0.25 ml
Impact resistance There shall be no crack, peeling off and remarkable damage
Weather resistance There shall be no crack, peeling off. The discoloration
shall be below No. 3 of Grey Scale.
Elongation At 20 392 %
At -10 25 %
After immersion in water 314 %
After heating 268 %
Fungus and mould resistance Compliant with JIS Z 2911
Algae resistance Using agar, there shall be no alga appearing.
Vapour permeability (g/m2 24hrs) 123 compliant with JIS Z 0208
Following cracks 0.6 mm based on zero expectation
Per square metre
15231 Proprietary elastic acrylic silicon resin colour coating system to tiled wall surfaces including tile filler.................................................................. 99.80 101.50 15231
15232 Ditto to plastered walls and soffits............................................................................................................................................................................... 61.50 66.00 15232
15/32
15 PAINTING 15
Item Item
PROPRIETARY PAINTWORK SYSTEM (CONT'D)
Proprietary polyurethane coating system of polyurethane resin, water based and coloured finishing coating Prepare and apply
comprising sealer coat, textured base coat and textured pattern topcoat, complying with the following New Redeco-
properties in accordance with the manufacturer's recommendation : - surfaces ration
A B
Product properties $ $
Sealer Acrylic emulsion resin sealer
Alkali resistant
Sealing and adhesion on different substrates
Topcoat Dust and dirt resistant
Fungus, Mould and algae resistant
Vapour permeable coating
Preventive of water penetration carbonation damage and salt-damage
Weather resistant
Fast drying
Material characteristics
Sealer Mixing ratio (wt %) 100%
water 0 ~ 20%
Coverage (kg/m2) 0.08 ~ 0.15
Roller tile finish SP tile finish Stipple finish
Base Mixing ratio (wt %) 100% 100% 100%
coat Water 2 ~ 4% Water 2 ~ 4% Water 2 ~ 4%
Coverage (kg/m2) 0.6 ~ 0.8 0.5 ~ 0.7 0.4 ~ 0.5
Topcoat Mixing ratio (wt %) 100% 100% 100%
Water 2 ~ 4% Water 2 ~ 4% Water 2 ~ 4%
Coverage (kg/m2) 0.6 ~ 0.8 0.5 ~ 0.7 0.4 ~ 0.5
Testing to JIS 5660
Condition in container Uniform condition without hard lumps when mixed.
Low temperature stability (-5) No deterioration
Application properties No application difficulties when applied twice.
Drying time 2 hours or less at 20
4 hours or less at 5
Appearance of film Film has normal appearance
Opacity (white and tint) 0.98
Gloss 82 or more
Water resistance More than 80% gloss retention after 96 hours immersion;
no abnormalities on the film surface
Alkali resistance More than 65% gloss retention after 7 days immersion;
no abnormalities on the film surface
Salt water resistance Pass 168 hours immersed in 3% sodium chloride solution
Wet scrub resistance Pass 1,000 cycles
Humidity and cool-heat cycling resistance More than 80% gloss retention ; no abnormalities on the
film surface.
Fungus and mould resistance Passed based on JIS Z 2911
Accelerated weather resistance More than 60% gloss retention after 480 hours test;
degree of chalking is 8 points or more; negligible change
in colour when compared to sample.
Weather resistance Degree of chalking is 6 points or more under 12 months
test; no cracking, swelling, holes, blistering; negligible
change in colour and gloss when compared to sample.
Per square metre
15233 Proprietary polyurethane coating system to tiled wall surfaces including tile filler.................................................................................................... 120.60 122.40 15233
15234 Ditto to plastered walls and soffits............................................................................................................................................................................... 75.50 90.00 15234
15/33
15 PAINTING 15
Item Item
PROPRIETARY PAINTWORK SYSTEM (CONT'D)
Proprietary spray-on granite coating system comprising undercoat, mid-coat, topcoat and clear topcoat, Prepare and apply
complying with the following properties in accordance with the manufacturer's recommendation : - New Redeco-
surfaces ration
Product properties A B
Textured finish $ $
Water base finishing material
Weather resistant
Dust and dirt resistant
Mildew and algae resistant
Matt / Semi-gloss finish
Material characteristics
Sealer Dilution ratio (wt %) 100 %
Water 0 ~ 20%
Coverage (kg/m2) 0.08 ~ 0.15
Mid coat Dilution ratio (wt %) 100 %
Water 3 ~ 5%
Coverage (kg/m2) 0.4 ~ 0.5
Topcoat Dilution ratio (wt %) 100%
Coverage (kg/m2) 0.7 ~ 0.8
Clear Dilution ratio (wt %) 100%
topcoat Water 0 ~ 20%
Coverage (kg/m2) 0.3 ~ 0.4
Testing
Workability to JIS K 5660 There shall be no problem in application
Drying time to JIS K 5660 Within 24 hours
Water resistance to JIS K 5660 There shall be no abnormality after immersion in water
for 96 hours.
Alkali resistance to JIS K 5660 There shall be no abnormality after immersion in water
for 48 hours.
Wet scrub resistance to JIS K 5660 There shall be no damage after scrubbing the surface
300 times.
Weather resistance to JIS K 5660 After 12 month test degree of whitening is 4 points or
more and there shall be no peeling and degree of
cracking and colour change shall be not more than
sample.
Per square metre
15235 Proprietary spray-on granite coating system to tiled wall surfaces including tile filler.............................................................................................. 286.60 288.20 15235
15236 Ditto to plastered walls and soffits............................................................................................................................................................................... 239.60 246.30 15236
15/34
15 PAINTING 15
Item Item
PROPRIETARY PAINTWORK SYSTEM (CONT'D)
Proprietary fluorine resin coating system comprising primer, texture base coat, mid-coat and topcoat, Prepare and apply
complying with the following properties in accordance with the manufacturer's recommendation : - New Redeco-
surfaces ration
Product properties A B
Ceramic film with hydrophilic property that allows easy-cleaning function $ $
Textured finish
Weather resistant
Heat resistant
Salt resistant
Chemical and solvent resistant
Colour coating resistant to ultra-violet ray
Fungus and algae resistant
Anti-staining mechanism
Material characteristics
Sealer Mixing ratio (wt %) 100 %
Water 0 ~ 20%
2
Coverage (kg/m ) 0.10 ~ 0.20
Texture Mixing ratio (wt %) 100 %
coat Water 0 ~ 6%
2
Coverage (kg/m ) 0.6 ~ 1.7
Pressing Press the texture with plastic roller dipped in paint thinner
Mid-coat Mixing ratio (wt %) 100%
Water 0 ~ 10%
Coverage (kg/m2) 0.15 ~ 0.17
Topcoat Mixing ratio (wt %) Base 100%
Hardener 6.67%
Water 0 ~ 10%
Coverage (kg/m2) 0.15 ~ 0.18
Testing
Stability at lower temperature (-5) to JIS K 5660 There is no change in quality.
Workability to JIS K 5660 There is no obstacle to apply materials twice by brush.
Drying time to JIS K 5660 20o C Less than 2 hours
Drying time to JIS K 5660 5o C Less than 4 hours
Appearance to JIS K 5660 There is no change in the appearance of paint film.
Hiding ability to JIS K 5660 0.98
Specular gloss to JIS K 5660 80
Water resistance to JIS K 5660 Immersion in water for 96 hours. The gloss retention ratio
is over 80% and there is no change in the paint film.
Alkali resistance to JIS K 5660 Immersion in alkali for 7 days. Gloss retention ratio is over
65% and there is no change in the paint film.
Wash ability to JIS K 5660 Possible to resist washing for 1,000 times.
Salt resistance to JIS K 5400 8.23 JIS K 5400 8.23 for 3,000 hours. No damage observed on
the dense film.
Heat resistance to JIS K 5660 The gloss retention is over 80% and possible to resist the
repetition of heat and cold.
Dirt resistance to JIS K 5660 5 : Value of grey scale after outdoor exposure test for 1 year.
Accelerated weather test to JIS K 5660 Tested by sunshine carbon arc type weather-o-meter for
2,000h and gloss retention ratio is over 80%.
Condition in container to JIS K 5660 When being stirred, it makes uniform condition without
any hard lumps. Based on JIS L0805 for grey scale
pollution level test with JIS K5660 6.16 methods. Compare
test specimen with model sample after 12 months outside
exposure.
Application properties to JIS K 5660 When making twice coating, no impediment for brushing work.
Humidity and cool-heat cycling resistance Gloss retention of 80% or more and endurable for
to JIS K 5660 humidity and cool-heat cycling test.
Water permeability (Test method B) (ml) 0.0 : JIS A 6909. Measure the amount of water
to JIS A 6909 permeated through the paint film of unit area per
definite time by using a water permeating tester. In this
testing method, measure the permeated water amount in
24 hours by using a water-permeating tester, and take the
value of permeated water amount converted to per 1 m2 of
paint film as the water permeability of the paint film.
Per square metre
15237 Proprietary fluorine resin coating system to tiled wall surfaces including tile filler................................................................................................... 267.80 274.00 15237
15238 Ditto to plastered walls and soffits............................................................................................................................................................................... 216.70 223.80 15238
15/35
15 PAINTING 15
Item Item
PROPRIETARY PAINTWORK SYSTEM (CONT'D)
Proprietary elastomeric acrylic waterproofing coating system comprising high strength primer / filler, Prepare and apply
one coat of acrylic alkali resisting primer and two coats of acrylic water resistance topcoat, complying New Redeco-
with the following properties in accordance with the manufacturer's recommendation : - surfaces ration
A B
Product properties $ $
Good hardness and dynamic anti-crack property
Strong adhesion and protection
Good hiding power
Good light fastness
Good water resistant
Alkali resistant
Fungus and algae resistant
Quick drying
Material characteristics
Primer / filler : High strength primer / filler consists of silicate, curing agent, fillers and additives
Finish Non-flat
Volume solid 34%
Flash point None
Primer : Acrylic Alkali Resisting Primer consists of acrylic copolymer emulsion
additives and water
Finish Glossy
Volume solid 25%
Flash point None
Topcoat : Acrylic Water Resistance Paint consists of acrylic copolymer emulsion,
pigments, fillers and additives etc.
Finish Flat
Volume solid 37%
Theoretical spreading rate 11.0 m / Ltr (1 coat on flat system)
Practical spreading rate 6.0 m / Ltr (1 coat on textured primers)
Flash point None
Testing
Status in Container to no any obstacle not found Liquefy status
Application properties to paint 2 coats without any No changes
difficulties
Repeat to frozen paints in 3 times under negative No changes
5 degree Celsius, place in room temperature in 6 hours
Hard drying time to dry to touch less than 2 hours Dry touch 0.5 hour
Water resistance No changes within 96 hours
Alkaline resistance No changes within 48 hours
Paint layer - Thermal dimensional stability to 5 times No changes
re-cycling in soaking at 23 degree Celsius 18 hours,
freezing at negative 20 degree Celsius in 3 hours
Contrast ratio 0.94
Wet scrub resistance cycles 10000 cycles without exposing the contrasting
colour of the undercoat
Air dirt 5%
Weathering hour 1000 hours
Chalking 1 class
Discoloration 1 class
Outlook status No blistering, no peeling off and no cracks
Per square metre
15239 Proprietary elastomeric acrylic waterproofing coating system to tiled wall surfaces including tile filler.................................................................. 157.20 159.90 15239
15240 Ditto to plastered walls and soffits............................................................................................................................................................................... 129.20 135.40 15240
15/36
15 PAINTING 15
Item Item
PROPRIETARY PAINTWORK SYSTEM (CONT'D)
Proprietary waterproofing coating system comprising water based acrylic co-polymer waterproof membrane Prepare and apply
with high quality pigmentation complying with the following properties in accordance with the manufacturer's New Redeco-
recommendation : - surfaces ration
A B
$ $
Product properties
Weathering resistant
CO2 resistant
High opacity
Testing
Carbon dioxide transmission 222 m
(Klopfer criterion R > 50 m)
Water vapour diffusion resistance 1.38 Sd cm
(Klopfer criterion SD < 4 m)
Water permeability ASTM E514-08 Class E (Highest resistance to water penetration)
Acoustic dampening : 500 micron sample Effective noise reduction : 2.5 dB
on Lysaght "Custom Orb" 26 gauge
thickness corrugated steel sheet
Chemical resistance Unaffected by a range of mild acids, alkalis, and is resistant
to bio-deterioration
Per square metre
15241 Proprietary waterproofing coating system to tiled wall surfaces including tile filler.................................................................................................. 179.20 185.30 15241
15242 Ditto to plastered walls and soffits............................................................................................................................................................................... 137.40 141.60 15242
15/37
15 PAINTING 15
Item Item
PROPRIETARY PAINTWORK SYSTEM (CONT'D)
Proprietary mineral silicate based coating system complying with the following properties in accordance with the Prepare and apply
manufacturer's recommendation : - New Redeco-
surfaces ration
Product properties A B
Binder : Combination of silica sol and water glass (sol-silicate) $ $
Direct and multi-purpose application to existing exterior surfaces without priming coat
Multi purpose application
UV and acid resistant, anti-static
High weathering resistance
Alkaline, non-flammable
Lightfast
Mineral matt
Water vapour permeable, non film forming and micro-porous
Highly water repellent
No solvents and plasticizers added
Resists algal and fungal growth
Material characteristics
Specific Weight : approx. 1.6g/cm3
pH value : approx. 11
Testing according to DIN EN 1062-1, ASTM E96, ASTM G154 and ASTM E514
Water vapour diffusion density V 2000g/m2d
Diffusion-equivalent air layer thickness Sd 0.01 m
Water permeability rate (24h) w < 0.1 kg/m2 h0.5
Gloss At 85 : 1.5
Per square metre
15243 Proprietary mineral silicate based coating system........................................................................................................................................................ 203.70 213.90 15243
Per linear metre
15244 Surfaces n.e. 150 mm girth........................................................................................................................................................................................... 34.60 36.40 15244
15245 Ditto but 150 - 300 mm girth........................................................................................................................................................................................ 62.00 65.10 15245
Each
15246 Small isolated article n.e. 0.01 m................................................................................................................................................................................ 14.30 15.00 15246
Sundries
A
Per square metre $
15247 Supply and apply 2 coats proprietary tile filler to tiled surface including cleaning all dirt,
dust and efflorescence on existing surface..................................................................................................................................................................................... 53.70 15247
Per linear metre
15248 Supply and apply proprietary pattern sticker in any width to the designated pattern as stipulated by Maintenance
Surveyor, including setting out, fixing and removal...................................................................................................................................................................... 35.90 15248
(Note:- The above Items 15247 to 15248 inclusive will only be paid for, if ordered by Maintenance Surveyor in writing.)
15/38
15 PAINTING 15
Item Item
PROPRIETARY FLOOR COATING SYSTEM
(Note : - The following Items 15249 to 15254 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
A
Per square metre $
15249 Proprietary floor harderner protection coating and sealer system to concrete or rendered surface, clear colour to floor in
accordance with the manufacturers instructions. The system shall increase the abrasion resistance of the floor surface
by minimum of 400% and also provide chemical resistance and dusting prevention. The system shall include (1) penetration
treatment with water based liquid comprising blend of metallic silico fluorides with absorption and penetration agent,
and (2) a final protection top coat................................................................................................................................................................................................... 87.30 15249
15250 Ditto but of coloured floor protection coating and sealer system.................................................................................................................................................. 101.90 15250
Proprietary floor coating system comprising minimum 2 coats of solvent based epoxy resin floor coating, capable to provide slip
resistance of appropriate coefficient of friction, on concrete floor or rendering floor including primer, all necessary surface
preparation and use of compatible primer, in strict accordance with the manufacturer's recommendation : -
A
Per square metre $
15251 On floors.......................................................................................................................................................................................................................................... 200.80 15251
15252 On floors with non-slip aggregate (fine grade) to achieve non-slip surfaces................................................................................................................................ 207.80 15252
Proprietary epoxy self-levelling heavy duty floor coating system comprising epoxy floor primer, solvent free epoxy undercoat
and epoxy floor paint, on concrete floor or rendering floor, all necessary surface preparation and use of compatible primer,
in strict accordance with the manufacturer's recommendation :
A
Per square metre $
15253 On floors.......................................................................................................................................................................................................................................... 376.10 15253
Proprietary fast-cure anti-skid slurry coating, 1mm thick, with calcined bauxite including applying compatible
sealer to existing tiled surface in accordance with the manufacturer's recommendation : -
A
Per linear metre $
15254 On nosing tile upto 100 mm wide.................................................................................................................................................................................................. 236.20 15254
15/39
15 PAINTING 15
Item Item
PROPRIETARY PAINTWORK TO SPORT HALL FLOORING SYSTEM Prepare and apply
New Redecor-
Proprietary paintwork to sport hall flooring system all in accordance with the manufacturer's recommendations : - surface ation
A B
Per square metre $ $
15255 General surface.............................................................................................................................................................................................................. 35.40 44.20 15255
Proprietary line marking to sport hall flooring system all in accordance with the manufacturer's
recommendations :
Per linear metre
15256 Line not exceeding 25 mm wide................................................................................................................................................................................... 23.30 28.80 15256
15257 Ditto but 25 - 50 mm wide............................................................................................................................................................................................ 26.20 34.30 15257
15258 Ditto but 50 - 75 mm wide............................................................................................................................................................................................ 29.40 38.70 15258
RE-ENAMEL PAINT ON SURFACE OF BATH TUB
Prepare and apply re-enamel paint on the following : -
A
Per number $
15259 Exposed surfaces of bath tub of any sizes and any type................................................................................................................................................................. 636.70 15259
15/40
15 PAINTING 15
Item Item
WRITING
Mark out and paint the following letters, etc., in one or more thick coats of synthetic paint as necessary to Re-
Oblit-
obtain bold and solid result, free from brush marks or obliterate existing including scraping or stripping off Paint paint
erate
letter and touching up paint to match general surface (in the case of repaint over or obliterate existing new over existing
writing, not measurable if surrounding surface being re-painted) : - existing
A B C
Each $ $ $
15260 Letter, number, Chinese character, logo, symbol and the like, n.e. 25 mm high.................................................................................... 6.20 7.30 4.20 15260
15261 Ditto but 25 - 75 mm high....................................................................................................................................................................... 4.80 6.00 6.80 15261
15262 Ditto but 75 - 150 mm high..................................................................................................................................................................... 7.50 8.20 9.10 15262
15263 Ditto but 150 - 225 mm high................................................................................................................................................................... 10.00 14.30 9.80 15263
15264 Ditto but 225 - 300 mm high................................................................................................................................................................... 12.10 14.70 15.70 15264
15265 Index hand or arrow n.e. 300 mm long.................................................................................................................................................... 9.70 11.00 10.40 15265
15266 Ditto but 300 - 600 mm long................................................................................................................................................................... 19.20 22.70 21.70 15266
15267 Ditto but 600 - 900 mm long................................................................................................................................................................... 30.00 33.70 40.30 15267
Per linear metre
15268 Line n.e. 25 mm wide............................................................................................................................................................................... 10.00 11.90 8.40 15268
15269 Ditto but 25 - 50 mm wide....................................................................................................................................................................... 14.60 14.80 13.70 15269
15270 Ditto but 50 - 75 mm wide....................................................................................................................................................................... 18.60 22.00 23.50 15270
Add to either of Items 15260 to 15270 inclusive for gold gilding in lieu of synthetic paint........................................................................................................ 300%
15/41
15 PAINTING 15
Item Item
PAPER HANGING Plain
fabric Textured Vinyl
Supply and fix approved wall paper : - backed vinyl with
vinyl cloth paper
cloth backed
A B C
Per square metre $ $ $
15271 Wall paper to plastered surfaces.............................................................................................................................................................. 49.90 66.90 31.10 15271
15272 Ditto but to gypsum plasterboard surfaces.............................................................................................................................................. 51.50 66.40 29.10 15272
15273 Ditto but to plywood surfaces.................................................................................................................................................................. 50.70 63.90 29.10 15273
15274 Wall paper of self-adhesive type to plastered surfaces........................................................................................................................... 55.30 76.20 28.70 15274
15275 Ditto but to gypsum plasterboard surfaces.............................................................................................................................................. 48.30 73.10 27.20 15275
15276 Ditto but to plywood surfaces.................................................................................................................................................................. 48.30 73.10 27.20 15276
15277 Hang only to plastered surfaces............................................................................................................................................................... 19.50 19.50 19.50 15277
15278 Ditto but to gypsum plasterboard surfaces.............................................................................................................................................. 19.30 19.30 19.30 15278
15279 Ditto but to plywood surfaces.................................................................................................................................................................. 18.10 18.10 18.10 15279
15280 Hang only wall paper of self-adhesive type to plastered surfaces.......................................................................................................... 15.40 15.40 15.40 15280
15281 Ditto but to gypsum plasterboard surfaces.............................................................................................................................................. 12.90 12.90 12.90 15281
15282 Ditto but to plywood surfaces.................................................................................................................................................................. 12.90 12.90 12.90 15282
MISCELLANEOUS ITEMS
A
Per square metre $
15283 Completely strip off existing washable distemper, anti-mould washable distemper, plastic emulsion paint, anti-mould acrylic
emulsion paint, textured emulsion paint, cement paint, textured cement paint, cold cure epoxy paint and polyurethane paint
by scraping or other approved means ............................................................................................................................................................................................ 14.10 15283
15284 Completely strip off existing synthetic, metallic, heat resisting, polyurethane or similar type of paint or varnish (any number
of coats) or lacquer on any surface by scraping combined with burning off, or using chemical solvents if necessary, and leaving
surface bare and clean, including washing down with neutralizing solution if chemical solvents have been used ................................................................... 16.00 15284
15285 Completely strip off existing wall paper by scraping or other approved means (not measurable if backing being removed in the
same operation)............................................................................................................................................................................................................................... 9.20 15285
15286 Extra over painting of any description for applying first or any subsequent coat by means of electrical or petrol driven
compressed spraying plant, including all masking, etc., when specifically ordered in writing ................................................................................................... 1.40 15286
(This item will not be paid for, if requested by the Contractor and is permitted to execute painting by spraying.)
15287 Stipple last coat of paint of any description on any surface when specifically ordered in writing............................................................................................... 11.10 15287
15288 Frost glass with one coat of paint to imitate ground glass (glazing bars not deducted)................................................................................................................ 15.90 15288
15289 Wash down new or existing surface with anti-mould liquid before decorating or re-decorating................................................................................................. 6.00 15289
15290 Prepare new or existing wall or ceiling surface and apply one liberal coat of silicone water repellent liquid............................................................................. 26.70 15290
15291 Ditto but two coats ditto.................................................................................................................................................................................................................. 42.90 15291
15/42
15 PAINTING 15
Item Item
SUNDRY CLEANING AND SEALING ITEMS
(Note : - The following Items 15292 to 15309 inclusive shall only be paid for, if ordered by the Maintenance Surveyor in writing.
Normal cleaning up and removal of paint stains, etc., after execution of decoration or any other work, have been allowed for in the
rates throughout this Schedule.)
A
Per square metre $
15292 Thoroughly scrub and wash down surfaces of Shanghai plaster in any position with stiff hard bristle brushes and detergent in hot
or cold water, and rinse down with fresh water and leave clean and free from dirt, stains and the like ..................................................................................... 7.70 15292
15293 Scrub clean existing terrazzo or rubbed granolithic paving, covering, skirting, etc., in any position with non-caustic fine scouring
powder and water, and rinse down with fresh water ..................................................................................................................................................................... 11.90 15293
15294 Add to Item 15293 for rubbing with carborandum blocks............................................................................................................................................................. 40.40 15294
15295 Apply one coat of wax emulsion to surfaces of terrazzo or rubbed granolithic after cleaning..................................................................................................... 8.30 15295
15296 Clean surfaces of thermo-plastic, vinyl, cork and similar flooring with detergent in water including scrubbing with soft bristle
brushes if necessary, and mopping over surface with damp mop afterwards .............................................................................................................................. 3.40 15296
15297 Apply one coat of wax emulsion to surfaces of thermo-plastic, vinyl, cork and similar flooring after cleaning, and buff up..................................................... 2.50 15297
15298 Sweep surface of cork flooring clean and apply two coats of approved sealer............................................................................................................................. 6.30 15298
15299 Scrub and clean surfaces of glazed or mosaic wall or floor tiling with solution of warm water and 10% hydrochloric or oxalic acid,
and rinse with fresh water............................................................................................................................................................................................................... 3.80 15299
15300 Scrub and clean surfaces of vitreous or glass mosaic tiles in any position with approved cleaning solution and rinse down with
fresh water....................................................................................................................................................................................................................................... 4.80 15300
15301 Clean down synthetic painted or varnished surfaces with soft soap or suitable detergent and water, with admixture of disinfectant
if required, and dry off with wash leather...................................................................................................................................................................................... 4.40 15301
15302 Clean down external painted surface with high pressure water jets.............................................................................................................................................. 6.60 15302
15303 Clean stonework or Shanghai plaster in any position with approved chemical stone cleaning solution and thoroughly wash off with
fresh water applied by high pressure water jets............................................................................................................................................................................. 7.90 15303
15304 Seal cleaned stonework or Shanghai plaster with approved chemical stone sealer and thoroughly wash off surplus with fresh water
applied by high pressure water jets................................................................................................................................................................................................. 10.20 15304
15305 Clean off letters, Chinese characters, graffiti etc., painted on stone, plastered or similar surfaces in synthetic paint, marking paint,
tar and the like with approved chemical cleaner including scrubbing and scraping as necessary, and thoroughly washing off
with fresh water applied by high pressure water jets..................................................................................................................................................................... 41.80 15305
Each
15306 Thoroughly scrub and clean existing W.C. pan and cistern, urinal stall, lavatory basin, sink and the like with spirits of salts and hot
water................................................................................................................................................................................................................................................ 15.60 15306
15307 Empty galvanized steel, concrete water cistern, cylinder or tank or fibreglass tanks n.e. 1.00 m internal volume, scrape or brush off
internally and remove all growth, rust, scale, etc., from bottom, sides and top, scrub out and clean with chloride of lime solution
(less than 1 kg chloride of lime to 6,000 litre of water) and thoroughly flush and wash through with fresh water .................................................................... 31.70 15307
15308 Ditto but 1.00 - 2.00 m.................................................................................................................................................................................................................. 39.90 15308
15309 Add to Item 15308 for each additional 1.00 m or part thereof in internal volume...................................................................................................................... 26.50 15309
15/43
15 PAINTING 15
Item Item
SUPPLY ONLY OF MATERIALS
A
Per litre $
15310 Emulsion paint..................................................................................................................................................................................................................................................
35.80 15310
15311 Textured emulsion paint.........................................................................................................................................................................................................................................
37.20 15311
15312 Cold cured epoxy paint (coloured) (Two pack type)...............................................................................................................................................................................................................
58.20 15312
15313 External textured paint.........................................................................................................................................................................................................................................
36.40 15313
15314 Anti-mould acrylic emulsion paint...............................................................................................................................................................................................................................
45.20 15314
15315 Multi-colour paint - Primer.....................................................................................................................................................................................................................................
52.90 15315
15316 Ditto - binder...........................................................................................................................................................................................................................................................
58.10 15316
15317 119.40
Ditto - Finishing coat.......................................................................................................................................................................................................................................... 15317
15318 Synthetic paint - Undercoat.....................................................................................................................................................................................................................................
34.10 15318
15319 Ditto - Gloss finishing coat....................................................................................................................................................................................................................................
36.30 15319
15320 Metallic paint - Aluminium bright finish........................................................................................................................................................................................................................
69.10 15320
15321 69.10 15321
Ditto - Copper alloy bronze finish..............................................................................................................................................................................................................................
15322 83.20
Non-toxic paint................................................................................................................................................................................................................................................. 15322
15323 78.00 15323
Polyurethane paint (coloured) (Two pack type)...................................................................................................................................................................................................................
15324 78.00 15324
Polyurethane paint (clear) (Ditto)..............................................................................................................................................................................................................................
Per square metre
15325 30.70 15325
Wall paper - Plain fabric backed vinyl cloth....................................................................................................................................................................................................................
15326 35.50 15326
Ditto - Plain fabric backed vinyl cloth of self-adhesive type...................................................................................................................................................................................................
15327 Ditto - Textured vinyl cloth....................................................................................................................................................................................................................................
44.00 15327
15328 77.20 15328
Ditto - Textured vinyl cloth of self-adhesive type..............................................................................................................................................................................................................
15329 16.90 15329
Ditto - Vinyl with paper backed.................................................................................................................................................................................................................................
15330 15.90 15330
Ditto - Vinyl with paper backed of self-adhesive type...........................................................................................................................................................................................................
15/44
Section 16
REPAIRS AND ALTERATION TO SPECIALTY WORKS
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
SECTION 16
REPAIRS AND ALTERATION TO SPECIALTY WORKS
SPECIAL CONDITIONS
Measurement SC16.01 This Section contains composite repair and alteration to specialty works which will
of repairs only be measured and paid for using rates of this Section provided that the following
and alteration conditions are met : -
generally
(a) The Maintenance Surveyor specifically orders that the repairs and alteration
to specialty works shall be executed by specialist's skilled labourers or
tradesmen in the manner and method as recommended and accepted by the
manufacturers;
(b) Submission of documentary evidence from the manufacturers of the
proprietary systems / products of the specialty works to the Maintenance
Surveyor demonstrating their compliance with the manufacturer's
recommendations as stated in item (a) above; and
(c) Submission of the proprietary systems / products for the repair and alteration
works, and/or the method statements of taking down, setting aside, repairs,
alterations and re-fixing or re-installation of the proprietary systems /
products shall be in accordance with the requirements as set out in the
Specifications; and in the absence of any specific requirements, then the
manufacturer's recommended methods. All proprietary systems / products
and/or method statements shall be approved by the Maintenance Surveyor
prior to commencement of works.
No measurement and payment shall be made under this Section if the repair to the
proprietary system / product is resulted from any of the cause(s) that is(are) covered
under the product warranty of the said system / product during the warranty period.
SC16.02 All repair and alteration items under this Section shall be measured as finished work
in place.
All composite items in this Section shall be measured as a whole item and shall not be
broken down and measured in constituent components, and rates for any constituent
components in the composite items that could be found in other Sections of the
Schedule shall not be permitted to apply to the valuation of the composite items,
unless with the written approval of the Maintenance Surveyor.
Measurement SC16.03 The area for concrete repair by patch repair shall be measured as net area over the
of concrete cracked, spalled or bulged surface and agreed by the Maintenance Surveyor.
repair by patch
repair Where the shortest distance between two isolated patches does not exceed 300 mm,
the total area of these isolated patches shall be added together and measured as one
whole patch area.
No deduction shall be made for any voids.
16/1
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
SPECIAL CONDITIONS
Measurement SC16.04 Injection type of concrete repair work shall be measured the net length of the crack
of concrete where drillholes or injection ports are placed along the crack (crack exceeding 150
repair by mm long) at 150 - 200 mm centres. Only crack with drillhole(s) or port(s) placed
chemical along shall be measured. The net length of crack n.e. 200 mm shall only be measured
injection when at least one drillhole or port is placed along the crack. All continuous cracks
without any drillhole or port shall deem to be covered by the measurement of the
crack with drillhole(s) or port(s).
Measurement SC16.05 The area for patch repair to proprietary roofing system and floor waterproofing system
of patch repair shall be measured net over the exposed finished top surface of the patch to be repaired.
of proprietary
roofing system No deduction shall be made for any voids and openings exceeding 0.50 m2.
and floor
waterproofing Measurement of patch repair under this Section shall not apply in the case of complete
system re-application of new roofing and floor waterproofing of which the measurement shall
be made under Section 07 - Roofing and Waterproofing.
Rates for SC16.06 The rates for concrete repair by patch repair shall include for : -
concrete repair
by patch repair (a) Submission of method statement supported by drawings showing different
phases of repair works and details of the temporary works employed.
(b) Submission of the product information of the proposed Repair Mortar
System (RMS) to be used including relevant test certificates showing
compliance with the material requirements of the Contract.
(c) Marking out of the identified areas of bulged, spalled or cracked concrete to
be repaired and obtaining agreement of the Maintenance Surveyor prior to
commencement of repair work.
(d) Preparation of a sample area to be patch repaired.
(e) Hacking back defective concrete areas and cutting back all loose or defective
concrete including saw cutting into the required depth and into neat
rectangular shape, to the extent as given in the Contract and as directed by
the Maintenance Surveyor.
(f) Preparation of concrete substrate after breaking out defective concrete,
roughening surfaces to expose aggregate of concrete areas and removing
loose materials, ready to receive repair mortar.
(g) Applying admixtures for use in any type of mortar complying with B.S. 4887
Pt.2: 1987, B.S. 5075 Pt. 1: 1982, B.S. 5075 Pt.3: 1985 or other approved
standards.
(h) Applying curing compound to the repair mortar in accordance with the
manufacturer's instructions.
(i) Applying approved epoxy resin, polyesters or cementitious based material
as grout to dowel bar installation.
(j) Preparation and cleaning of exposed lengths of existing steel reinforcement
using one of the cleaning methods as given in the Contract and as directed
by the Maintenance Surveyor.
16/2
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
SPECIAL CONDITIONS
Rates for SC16.06 (k) Applying primer and bond coat to concrete substrate and steel reinforcement.
concrete repair (Cont'd)
by patch repair (l) Preparing and applying the RMS in accordance with the manufacturer's
(Cont'd) instructions.
(m) Carrying out tests all in accordance with the Specification as adopted in the
Contract, including employing an approved independent testing laboratory
accredited by HOKLAS and submission of test reports.
(n) Submission of repair records upon completion.
(o) Finishing the repaired surfaces with rendering or tiled finish to match existing.
(p) Repairing, reinstating and repainting the affected areas to match existing.
Rates for SC16.07 The rates for concrete repair by chemical injection shall include for : -
concrete repair
by chemical (a) Provision of a competent full time site supervisor of minimum 3 years of
injection experience of concrete repair by chemical injection.
(b) Submission of method statement supported by a proposal of field trial
testing, controlling attributes on suitability and injectability of the proposed
chemical injection system, and details of the temporary works employed
together with drawings and calculations.
(c) Submission of the product information of the proposed chemical
injection system to be used including relevant test certificates showing
compliance with the material requirements of the Contract, material
safety data sheets showing hazards of the materials and control measures
and other information as required.
(d) Marking out the locations and extent of cracks to be repaired and obtaining
agreement of the Maintenance Surveyor prior to commencement of repair
work.
(e) Preparation of cracks by removing all loose debris by brushing or
blowing out with clean compressed air, removing all defective concrete,
and making good all reinforcing bars before injection.
(f) Carrying out drilling of injection holes into concrete and applying the
chemical injection in accordance with the manufacturer's instructions.
(g) Carrying out tests all in accordance with the Specification as adopted in the
Contract, including employing an approved independent testing laboratory
accredited by HOKLAS and submission of test reports.
(h) Submission of repair records upon completion.
(i) Finishing the repaired surfaces by grounding flat to form a smooth
surface and applying rendering or tiled finish to match existing.
(j) Repairing, reinstating and repainting the affected areas to match existing.
16/3
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
SPECIAL CONDITIONS
Rates for SC16.08 The rates for patch repair to proprietary roofing system and floor waterproofing
patch repair to system shall include for : -
proprietary
roofing system (a) Carrying out the repairs in patches and isolated areas.
and floor
waterproofing (b) Roofing or waterproofing to flat, sloping or curved roofs or floors.
system
(c) Inspection, preparing, cleaning and drying surfaces including removing all
contaminants, dusts, loose stones, debris and the like.
(d) Dressing to sides or ends of upstands, gutters, flashings, skirtings, edge
coverings, steps and the like, including angles, junctions, turn-in edges,
welted drips and the like all in accordance with the manufacturer's
instructions.
(e) Making good surfaces of substrate including filling cracks with bitumen,
emulsion or any other materials recommended by the manufacturer's
recommendations.
(f) Carrying out the necessary tests in accordance with the Specification and/or
the manufacturer's recommendation, all to the satisfaction of the Maintenance
Surveyor.
(g) Replacement of roofing and floor waterproofing installation if failing in the
non-destructive test.
(h) Providing protective boarding in accordance with the manufacturer's
instructions, if required.
(i) Providing all reports and maintenance manuals upon completion.
Rates for SC16.09 The rates for repairs and alteration to existing proprietary demountable partition system
repairs and shall include for : -
alterations
to existing (a) Taking down, clearing away, setting aside for re-use and/or fixing existing
proprietary partitions, framing, covering materials, etc., as recommended by the
demountable manufacturer and the rate inclusion items as stated in General Regulations
partition Clauses GR.15 to GR.17.
system
(b) Replacement and provision of new compatible fittings and fixing accessories
including additional accessories as necessary, and provision of any ancillary
works as may be required by the manufacturer.
(c) Modifying existing openings, finishes or covering to suit actual site conditions.
(d) Making good surfaces disturbed.
(e) Multi-handling and delivery between the designated locations and storage
area as directed.
(f) Proper protection to the partitions, framing, fittings and accessories for
storage and re-use.
(g) Modifications on existing framing including provisions of additional framing
as required.
16/4
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
SPECIAL CONDITIONS
Rates for "fix SC16.10 The rates for "fix only" of existing fully glazed or partly glazed demountable partition
only" of existing shall include for : -
fully glazed or
partly glazed (a) Replacement of any glazing panel if damaged when carrying out repair and
demountable alteration to the demountable partition.
partition
Rates for SC16.11 The rates for repairs and alteration to existing proprietary fume cupboards shall further
repairs and include for : -
alteration to
existing (a) Taking down, clearing away, setting aside for re-use and/or fixing existing
proprietary fume cupboards including all fittings, components, services connections, etc.,
fume cupboards as recommended by the manufacturer and the rate inclusion items as stated in
General Regulations Clauses GR.15 to GR.17.
(b) Replacement and provision of new compatible fittings and fixing accessories
including additional accessories as necessary and provision of any ancillary
works as may be required by the manufacturer.
(c) Replacement of any glazing panel if damaged when carrying out repair and
alteration to the fume cupboards.
(d) Provision of connection to nearest power point by registered electrical workers.
(e) Making good surfaces disturbed.
(f) Carrying out testing and commissioning to the satisfaction of the Maintenance
Surveyor.
Rates for SC16.12 The rates for repairs to existing proprietary automatic swing or sliding doors shall
repairs to further include for : -
existing
proprietary (a) Taking down, clearing away, setting aside for re-use and/or fixing existing
automatic automatic swing or sliding doors including door frames, door operator,
swing or sliding automatic mechanism, interlocking devices and all necessary accessories,
doors ironmongeries and the like, as recommended by the manufacturer and the
rate inclusion items as stated in General Regulations Clauses GR.15 to
GR.17.
(b) Replacement and provision of new compatible fittings and fixing accessories
including additional accessories as necessary, provision of any ancillary
works as may be required by the manufacturer.
(c) Replacement of any glazing panel if damaged when carrying out repair to the
automatic swing or sliding doors.
(d) Provision of connection to nearest power point by registered electrical
workers.
(e) Making good surfaces disturbed.
(f) Carrying out testing and commissioning to the satisfaction of the Maintenance
Surveyor.
16/5
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
Item Item
CONCRETE REPAIR BY PATCH REPAIR
Thickness (mm)
(Note : - Items 16001 to 16005 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.) Additional
10mm 15mm 5mm
A B C
Per square metre $ $ $
16001 Prepare and apply proprietary pre-bagged or site batched Class 25 polymer modified concrete repair mortar to existing
concrete substrate complying with the following specification including breaking out and preparation of surfaces,
preparation and cleaning of existing steel reinforcement, both using methods as specified; applying prime coat to
steel reinforcement; applying bond coat to concrete substrate and primed steel reinforcement; carrying out
field trial test, works test, testing on grouted dowel bars and completed patch repairs, etc. all in accordance
with the manufacturer's instructions : -
Compressive strength at 28 days 20 - 40 MPa
Minimum tensile strength at 7 days 1.5 MPa
Elastic modulus at 28 days 9 - 15 kN/mm2
Minimum bond strength at 7 days 1.5 MPa
Cracking during the Coutinho ring test at 7 days 0
Minimum figg air permeability in seconds 150
..................................................................................................................................................................................................................... 232.90 291.10 52.40 16001
16002 Prepare and apply proprietary pre-bagged or site batched Class 40 polymer modified concrete repair mortar to existing
concrete substrate complying with the following specification including breaking out and preparation of surfaces,
preparation and cleaning of existing steel reinforcement, both using methods as specified; applying prime coat to
steel reinforcement; applying bond coat to concrete substrate and primed steel reinforcement; carrying out
field trial test, works test, testing on grouted dowel bars and completed patch repairs, etc. all in accordance
with the manufacturer's instructions : -
Compressive strength at 28 days 30 - 60 MPa
Minimum tensile strength at 7 days 2.0 MPa
Elastic modulus at 28 days 15 - 25 kN/mm2
Minimum bond strength at 7 days 2.0 MPa
Cracking during the Coutinho ring test at 7 days 0
Minimum figg air permeability in seconds 200
..................................................................................................................................................................................................................... 247.40 305.60 52.40 16002
16/6
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
Item Item
CONCRETE REPAIR BY PATCH REPAIR (CONT'D) Thickness (mm)
40mm Additional
5mm
A B
Per square metre $ $
16003 Prepare and apply proprietary pre-bagged or site batched Class 25 high-build polymer modified concrete repair mortar to
existing concrete substrate complying with the following specification including breaking out and preparation of surfaces,
preparation and cleaning of existing steel reinforcement, both using methods as specified; applying prime coat to
steel reinforcement; applying bond coat to concrete substrate and primed steel reinforcement; carrying out
field trial test, works test, testing on grouted dowel bars and completed patch repairs, etc. all in accordance
with the manufacturer's instructions : -
Compressive strength at 28 days 20 - 40 MPa
Minimum tensile strength at 7 days 1.5 MPa
Elastic modulus at 28 days 9 - 15 kN/mm2
Minimum bond strength at 7 days 1.5 MPa
Cracking during the Coutinho ring test at 7 days 0
Minimum figg air permeability in seconds 150
....................................................................................................................................................................................................................................... 320.20 101.90 16003
16004 Prepare and apply proprietary pre-bagged or site batched Class 40 high-build polymer modified concrete repair mortar to
existing concrete substrate complying with the following specification including breaking out and preparation of surfaces,
preparation and cleaning of existing steel reinforcement, both using methods as specified; applying prime coat to
steel reinforcement; applying bond coat to concrete substrate and primed steel reinforcement; carrying out
field trial test, works test, testing on grouted dowel bars and completed patch repairs, etc. all in accordance
with the manufacturer's instructions : -
Compressive strength at 28 days 30 - 60 MPa
Minimum tensile strength at 7 days 2.0 MPa
Elastic modulus at 28 days 15 - 25 kN/mm2
Minimum bond strength at 7 days 2.0 MPa
Cracking during the Coutinho ring test at 7 days 0
Minimum figg air permeability in seconds 200
....................................................................................................................................................................................................................................... 349.30 108.40 16004
16/7
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
Item Item
CONCRETE REPAIR BY PATCH REPAIR (CONT'D) Thickness (mm)
10mm 15mm Additional
5mm
A B C
Per square metre $ $ $
16005 Prepare and apply proprietary shrink resistant mortar consisting a mixture of cement, aggregate, water and
a shrink resistant admixture, to existing concrete substrate complying with the following specification
including breaking out and preparation of surfaces, preparation and cleaning of existing steel reinforcement,
both using methods as specified; applying prime coat to steel reinforcement; applying bond coat to concrete
substrate and primed steel reinforcement; carrying out field trial test, works test, testing on grouted dowel bars
and completed patch repairs, etc. all in accordance with the manufacturer's instructions : -
Minimum compressive strength at 28 days 40 MPa
Elastic modulus at 28 days 15 - 25 kN/mm2
Minimum bond strength at 7 days 2.5 MPa
Range of unrestrained plastic expansion
(ASTM C827-01(a)) 1-4%
Maximum drying shrinkage at 28 days 50 micro-strain
..................................................................................................................................................................................................................... 247.40 305.60 52.40 16005
CONCRETE REPAIR BY CHEMICAL INJECTION
Wall Ceiling
(Note : - Items 16006 to 16007 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.) surface surface
A B
Per linear metre $ $
16006 Prepare and apply proprietary low viscosity high-strength epoxy grout injection to cracks of any size and thickness
complying with the following specification including carrying out crack preparation, filling cracks with compatible
materials, field trial test, coring test, etc., all in accordance with the manufacturer's instructions : -
Tensile strength at 7 days tested according to >48.0 MPa, unless for non-load bearing
ASTM D638-08: or minor structural elements as to be
agreed by the Maintenance Surveyor but
shall not be less than 35.0 MPa.
or
Tensile strength at 7 days tested according to
BS 6319-7: >15.0 MPa
Bond strength tested according to ASTM
C-882
at 2 days (moist cure) >7.0 MPa
at 14 days (moist cure) >10.0 MPa
or
Bond strength tested according to
BS EN 12618-2
at 14 days for resin injection systems >2.0 Mpa
at 28 days (moist cure) for cementitious >2.0 MPa
injection systems
....................................................................................................................................................................................................................................... 334.70 363.80 16006
16/8
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
Item Item
CONCRETE REPAIR BY CHEMICAL INJECTION (CONT'D) Wall Ceiling
surface surface
A B
Per linear metre $ $
16007 Prepare and apply proprietary flexible polyurethane grout injection to cracks of any size and thickness
complying with the following specification including carrying out crack preparation, filling cracks with compatible
materials, field trial test, coring test, etc., all in accordance with the manufacturer's instructions : -
Specific gravity at 25 degree Celsius: 1.1 @ 25 C
Elongation: > 34 %
Bond Strength @ 24 hours in MPa: > 0.28
....................................................................................................................................................................................................................................... 414.80 443.90 16007
REPAIRS TO PROPRIETARY ROOFING SYSTEM OR FLOOR
WATERPROOFING SYSTEM
Liquid applied
Sheet material
material
requiring self requiring self
protection finished protection finished
A B C D
Per square metre $ $ $ $
16008 Carry out repair of existing roofing or floor waterproofing system in patches or isolated areas by cutting
through the complete thickness of the system, preparing, applying proprietary roofing or floor waterproofing,
resealing after inspection and making good disturbed surfaces, all in accordance with the manufacturer's
instructions (concrete roof tiles and cement and sand screed are measured separately)......................................................... 141.90 175.00 156.10 189.20 16008
A
Per square metre $
16009 Carry out repair of existing roofing or floor waterproofing system in patches or isolated areas by cutting through the complete
thickness of the system, preparing and spray applying proprietary high build acrylic waterproofing membrane comprising primer
and top coat, resealing after inspection and making good disturbed surfaces, all in accordance with the manufacturer's
instructions (concrete roof tiles and cement and sand screed are measured separately)............................................................................................................... 681.10 16009
16/9
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
Item Item
REPAIRS TO PROPRIETARY DEMOUNTABLE PARTITION SYSTEMS
AND SUNDRY ITEMS
Take Take
down down Fix
and and set only
clear aside for
away re-use
A B C
Per square metre $ $ $
16010 Proprietary demountable partition system complete with panel covering to both sides of partition,
with or without applied finishes, stud framework, infilled sound insulation, fittings and accessories, if any ........................................ 72.80 109.30 167.50 16010
16011 Ditto but fully glazed or partly glazed demountable partition................................................................................................................... 87.40 131.10 203.90 16011
16012 Proprietary demountable partition system as security / fire resisting / fire resisting security partition
complete with panel covering to both sides of partition, with or without applied finishes, stud framework,
infilled sound insulation, door and accessories, if any............................................................................................................................... 87.40 131.10 203.90 16012
Each
16013 Hollow or solid core flush door (single leaf measured)............................................................................................................................. 72.80 109.30 145.70 16013
ALTERATION WORKS TO EXISTING PROPRIETARY DEMOUNTABLE
PARTITION SYSTEM
Plaster- Plywood/
board chipboard
panel panel
covering covering
A B
Per square metre $ $
16014 Replace panel covering 12.5 mm (min.) thick to one side of existing demountable partition with panel covering finished
with laminated vinyl wall paper.................................................................................................................................................................................... 156.10 182.30 16014
16015 Ditto with fabric sheeting.............................................................................................................................................................................................. 194.30 218.50 16015
16016 Ditto with timber veneer sheeting................................................................................................................................................................................. 202.20 234.70 16016
16017 Ditto with laminated plastic sheeting........................................................................................................................................................................... 208.10 241.20 16017
16018 Ditto with 13 mm thick softboard covered with Hessian fabric.................................................................................................................................. 241.20 267.40 16018
16/10
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
Item Item
ALTERATION WORKS TO EXISTING PROPRIETARY DEMOUNTABLE
PARTITION SYSTEM (CONT'D)
A
Per square metre $
16019 Alter existing fully glazed demountable partition to double glazed demountable partition with 6 mm thick clear glass............................................................ 413.80 16019
16020 Ditto but with 6 mm thick obscure glass........................................................................................................................................................................................ 444.80 16020
16021 Ditto but with 6 mm thick wired glass........................................................................................................................................................................................... 611.50 16021
16022 Alter existing demountable partition to insert 50 mm thick fibreglass insulation layer (density not less than 16 kg/m)........................................................... 30.60 16022
16023 Ditto but density 48 kg/m.............................................................................................................................................................................................................. 49.20 16023
16024 Construct timber louvre consisting of 45 x 20 mm thick timber framing all round, 10 mm thick timber blades and
25 x 5 mm thick timber architrave including forming opening through existing hollow or solid core flush door
and providing all necessary framing............................................................................................................................................................................................... 727.70 16024
16025 Forming opening of any size through demountable partition including all necessary partition components............................................................................... 136.40 16025
Each
16026 Construct glazed sliding hatch, size 1200 x 450 mm high, consisting of 125 x 25 mm thick timber framing all
round, 6 mm thick clear sheet glass with polished edges and finger hole, P.V.C. tracks housed into framing
at head and cill including forming opening in existing demountable partition, providing and fixing of all necessary
framing components........................................................................................................................................................................................................................ 902.50 16026
16027 Construct 15 mm thick plywood blind box overall size 600 x 340 x 80 mm deep and lined with 13 mm thick
soft board......................................................................................................................................................................................................................................... 641.00 16027
16028 Scribe infill up to 300 mm wide in 12 mm thick luan plywood to existing window opening for abutting demountable partition
of any description and height, and finished to match abutting partition....................................................................................................................................... 548.80 16028
16/11
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
Item Item
REPAIRS TO PROPRIETARY FUME CUPBOARDS
A
Per set $
16029 Take down and clear away existing proprietary fume cupboard of varying dimensions complete with air flow indicator control,
safety devices, control and monitoring system, ductwork of upto 3 m long, exhaust extraction system and steel support frame,
extraction fan, motor and enclosure, worktop, sink, fittings and accessories, and disconnecting and capping off
ductwork and nearby power, water and gas services..................................................................................................................................................................... 510.50 16029
16030 Take down and set aside for re-use ditto........................................................................................................................................................................................ 593.40 16030
16031 Fix only existing proprietary fume cupboard of varying dimensions complete with air flow indicator control, safety devices,
control and monitoring system, ductwork of upto 3 m long, exhaust extraction system and steel support frame,
extraction fan, motor and enclosure, worktop, sink, fittings and accessories, and re-connection to ductworks and
nearby power, water and gas services............................................................................................................................................................................................. 1,021.10 16031
16032 Take down and clear away existing proprietary school-type fume cupboard of varying dimensions with two-compartment base
storage cupboard and glass panels complete with air flow indicator control, safety devices, control and monitoring system,
ductwork of upto 3 m long, exhaust extraction system and steel support frame, extraction fan, motor and enclosure, worktop,
sink, fittings and accessories, and disconnecting and capping off ductwork and nearby power, water and gas
services............................................................................................................................................................................................................................................ 510.55 16032
16033 Take down and set aside for re-use ditto........................................................................................................................................................................................ 593.40 16033
16034 Fix only existing proprietary school-type fume cupboard of varying dimensions with two-compartment base storage cupboard and
glass panels complete with all air flow indicator control, safety devices, control and monitoring system, ductwork of upto 3 m long,
exhaust extraction system and steel support frame, extraction fan, motor and enclosure, worktop, sink, fittings and
accessories, and re-connection to ductworks and nearby power, water and gas services ............................................................................................................ 1,021.10 16034
16/12
16 REPAIRS AND ALTERATION TO SPECIALTY WORKS 16
Item Item
REPAIRS TO EXTENSION DUCTWORK AND EXHAUST FANS TO FUME CUPBOARDS
A
Per linear metre $
16035 Take down and clear away existing 250 mm diameter extension ductwork connecting to exhaust system of proprietary
fume cupboard complete with steel support frame and fixing accessories and connectors to exhaust outlet.............................................................................. 63.00 16035
16036 Take down and set aside for re-use ditto........................................................................................................................................................................................ 96.70 16036
16037 Fix only existing 250 mm diameter extension ductwork in polypropylene or similar approved materials connecting
to exhaust system of proprietary fume cupboard, mounted either on internal or external wall or roof, complete
with steel support frame and fixing accessories if required; connectors to exhaust outlet, all necessary builder's
works as required; testing and commissioning on completion of the whole exhaust system in conjunction with
the proprietary fume cupboard........................................................................................................................................................................................................ 126.00 16037
Per set
16038 Take down and clear away existing exhaust fan and motor complete with steel support frame, enclosure for fan and motor, safety
devices, control and monitoring panel, connectors to the extended ductwork and exhaust system, and fixing accessories
and disconnecting from ductworks................................................................................................................................................................................................. 84.60 16038
16039 Take down and set aside for re-use ditto........................................................................................................................................................................................ 126.90 16039
16040 Fix only existing exhaust fan and motor complete with steel support frame, enclosure for fan and motor, fixing accessories,
and re-connection to extended ductworks, mounted either on external wall or roof, all necessary safety devices, control
and monitoring panel, connectors to the extended ductwork and exhaust system, builder's works as required, including
electrical wiring and all connection by a registered electrical worker, and testing and commissioning on completion
in conjunction with the proprietary fume cupboard and associated ductworks............................................................................................................................ 301.10 16040
REPAIRS TO PROPRIETARY AUTOMATIC SWING OR SLIDING DOOR SYSTEMS Single Double
leaf leaf
door door
A B
Per set $ $
16041 Take down and clear away proprietary automatic swing or sliding door system complete with door, frames, hood,
tracks, perimeter housing, ironmongery, electrical motor, control unit and associated wiring and electrical devices............................................... 212.20 318.20 16041
16042 Take down and set aside for re-use proprietary automatic swing or sliding door system complete with door and
ironmongery (excluding frames), electrical motor, control unit and associated wiring and electrical devices.......................................................... 318.20 475.00 16042
16043 Fix only proprietary automatic swing or sliding door system complete with door and ironmongery (excluding frame) including
connection to electrical motor, control unit and associated wiring, and testing and commissioning on completion................................................. 682.80 1,024.10 16043
16/13
Section 17
LABOUR
17 LABOUR 17
SECTION 17
LABOUR
SPECIAL CONDITIONS
Payment for SC17.01 Wherever possible, work executed under the Contract shall be measured and paid for as
labour trade items. Payment for labour on an hourly basis will not be made except in special
circumstances where specifically ordered in writing by the Maintenance Surveyor.
Measurement SC17.02 The measurement of labour shall be the aggregate time employed on the item of labour
generally to the nearest hour for any time in a 24-hour day (from 00:00 hour to 24:00 hour on the
same day) including all Sundays and General Holidays. No measurement shall be made for
meal breaks, rest period and travelling time. The Contractor will be paid for those labours
who are actually at work and ordered by the Maintenance Surveyor in writing.
Allowance for overtime work and any cost/expenses incurred therein is deemed to be
included in the Contract Percentage(s) applied to the Contract. Reference shall also be
made to General Regulations Clauses GR.04 and GR.12.
Any lodging and living accommodation allowance, if any, for labours is not reimbursable and
shall not be measured separately.
Measurement of SC17.03 The measurement of special attendance on Building Works and on Building Services
special attendance Installation shall be the time required for the general worker or electrical fitter to
on Building Works stand-by and to provide any attendance or services as directed by the Maintenance
and on Building Surveyor in the Works Order.
Services Installation
Rates for SC17.04 The rates for labour shall generally include for : -
labour
generally (a) Work being in any district.
(b) Use and maintenance of hand tools and appliances, non-mechanical plant
and equipment (such as ladders, trestles, stages, temporary track, wagons,
skips and similar items).
(c) Protective clothing and safety equipment.
(d) Contractor's site supervision and employee insurance.
(e) Meal breaks and rest periods.
(f) Contractor's profit, establishment charges and overheads.
(g) Allowance for travelling expenses and time to and from the Site.
(h) Pager and mobile phone including payment of all charges incurred.
17/1
17 LABOUR 17
SPECIAL CONDITIONS
Rates for SC17.04 (i) Contributions to Mandatory Provident Fund.
labour (Cont'd)
generally (j) Paid leave allowance.
(Cont'd)
(k) Any other allowances as required.
(l) Submission of documentary proof of qualifications, registration, certificates
and/or licenses in accordance with the Construction Workers Registration
Ordinance (Cap. 583).
Rates for SC17.05 The rates for Registered Skilled Worker (for designated trade) shall further
Registered include for : -
Skilled Worker
(for designated (a) Workers who have registered under the Construction Workers Registration
trade) Ordinance (Cap. 583) as a registered skilled worker for a designated trade
and possess a trade test certificate issued by the Construction Industry
Council (CIC) or former Construction Industry Training Authority (CITA) or
Vocational Training Council (VTC), or other qualifications as specified by the
Ordinance or other recognized registration, certificates or licenses acceptable
to the Maintenance Surveyor.
(b) Workers who have registered under the Construction Workers Registration
Ordinance (Cap. 583) as a registered skilled worker (provisional) for a
designated trade and possesses not less than six years of relevant experience
to personally carry out construction work of a particular trade as specified
under the Ordinance.
Rates for SC17.06 The rates for Registered Semi-skilled Worker (for designated trade) shall
Registered Semi- further include for : -
skilled Worker
(for designated (a) Workers who have registered under the Construction Workers Registration
trade) Ordinance (Cap. 583) as a registered semi-skilled worker for a designated
trade and possess an intermediate trade test certificate issued by the CIC or
former CITA or VTC, or other qualifications as specified by the Ordinance
or other recognized registration, certificates or licenses acceptable to the
Maintenance Surveyor.
(b) Workers who have registered under the Construction Workers Registration
Ordinance (Cap. 583) as a registered semi-skilled worker (provisional) for a
designated trade and possesses not less than two years of relevant
experience to personally carry out construction work of a particular trade as
specified under the Ordinance.
Rates for SC17.07 The rates for Demolition Worker shall include for demolition worker for building
Demolition and unauthorized building works.
Worker
Rates for SC17.08 The rates for Floor Layer shall include for floor layer for PVC flooring, timber
Floor Layer flooring and any other types of flooring systems.
17/2
17 LABOUR 17
SPECIAL CONDITIONS
Rates for SC17.09 The rates for Plant and Equipment Operator (other than cranes) shall include
Plant and for the following types of operators : -
Equipment
Operator (a) Plant and Equipment Operator (Bulldozer)
(other than
cranes) (b) Plant and Equipment Operator (Excavator)
(c) Plant and Equipment Operator (Loader)
(d) Plant and Equipment Operator (Mini-loader with or without attachment)
(e) Plant and Equipment Operator (Demolition) - Excavator
(f) Plant and Equipment Operator (Suspended Working Platform)
Rates for SC17.10 The rates for Plant and Equipment Operator (cranes generally) shall include for the
Plant and following types of operators : -
Equipment
Operator (a) Plant and Equipment Operator (Crawler-mounted Mobile Crane)
(cranes generally)
(b) Plant and Equipment Operator (Gantry Crane)
(c) Plant and Equipment Operator (Tower Crane)
(d) Plant and Equipment Operator (Truck-mounted Crane)
(e) Plant and Equipment Operator (Wheeled Telescopic Mobile Crane)
Rates for SC17.11 The rates for Fire Service Fitter shall include for the following types of fitters : -
Fire Service
Fitter (a) Fire Service Electrical Fitter
(b) Fire Service Mechanical Fitter
(c) Fire Service Potable Equipment Fitter
Rates for SC17.12 The rates for Refrigeration / Air-conditioning / Ventilation Mechanic shall include
Refrigeration / for the following types of mechanics : -
Air-conditioning /
Ventilation (a) Refrigeration / Air-conditioning / Ventilation Mechanic (Air System)
Mechanic
(b) Refrigeration / Air-conditioning / Ventilation Mechanic (Electrical control)
(c) Refrigeration / Air-conditioning / Ventilation Mechanic (Thermal insulation)
(d) Refrigeration / Air-conditioning / Ventilation Mechanic (Unitary System)
(e) Refrigeration / Air-conditioning / Ventilation Mechanic (Water System)
17/3
17 LABOUR 17
SPECIAL CONDITIONS
Rates for SC17.13 The rates for Registered General Worker shall further include for : -
Registered
General Worker (a) General worker and labourer who hold a valid Green Card.
17/4
17 LABOUR 17
Item Item
LABOUR Registered Worker
(for designated
BUILDING WORKS trade)
Semi-
Skilled
skilled
Worker
Worker
A B
Per hour $ $
17001 Asphalter (Road Construction)..................................................................................................................................................................................... 107.40 - 17001
17002 Bamboo Scaffolder........................................................................................................................................................................................................ 187.20 131.00 17002
17003 Bar Bender and Fixer.................................................................................................................................................................................................... 214.30 150.00 17003
17004 Bricklayer...................................................................................................................................................................................................................... 136.70 95.70 17004
17005 Builder's Lift Operator................................................................................................................................................................................................... - 66.60 17005
17006 Carpenter (Formwork - Building Construction)........................................................................................................................................................... 201.10 140.80 17006
17007 Concrete Repairer (Spalling Concrete)......................................................................................................................................................................... 185.60 - 17007
17008 Concretor....................................................................................................................................................................................................................... 194.50 136.10 17008
17009 Construction Plant Mechanic........................................................................................................................................................................................ 150.60 105.40 17009
17010 Demolition Worker........................................................................................................................................................................................................ 165.60 - 17010
17011 Drainlayer...................................................................................................................................................................................................................... 166.00 116.20 17011
17012 Floor Layer..................................................................................................................................................................................................................... 139.20 97.40 17012
17013 General Welder.............................................................................................................................................................................................................. 152.00 106.40 17013
17014 Glazier........................................................................................................................................................................................................................... 154.80 108.40 17014
17015 Joiner............................................................................................................................................................................................................................. 139.20 97.40 17015
17016 Leveller.......................................................................................................................................................................................................................... 150.20 105.10 17016
17017 Marble Worker.............................................................................................................................................................................................................. 179.80 125.80 17017
17018 Mason............................................................................................................................................................................................................................ 146.10 106.40 17018
17019 Metal Scaffolder............................................................................................................................................................................................................ 131.00 89.80 17019
17020 Metal Worker................................................................................................................................................................................................................. 154.70 108.30 17020
17021 Painter and Decorator.................................................................................................................................................................................................... 127.40 89.20 17021
17022 Painter (Texture-Spray)................................................................................................................................................................................................. - 154.10 17022
17023 Pipelayer........................................................................................................................................................................................................................ 166.00 - 17023
17024 Plant and Equipment Operator (other than cranes) ..................................................................................................................................................... 129.60 - 17024
17025 Plant and Equipment Operator (cranes generally)........................................................................................................................................................ 168.50 - 17025
17026 Plasterer......................................................................................................................................................................................................................... 154.70 108.30 17026
17027 Plumber......................................................................................................................................................................................................................... 140.20 102.30 17027
17/5
17 LABOUR 17
Item Item
LABOUR (CONT'D) Registered Worker
(for designated
BUILDING WORKS (CONT'D) trade)
Semi-
Skilled
skilled
Worker
Worker
A B
Per hour $ $
17028 Rigger / Metal Formwork Erector................................................................................................................................................................................. 160.40 112.30 17028
17029 Rock Breaking Driller................................................................................................................................................................................................... 163.90 - 17029
17030 Structural Steel Erector................................................................................................................................................................................................. 191.30 133.90 17030
17031 Structural Steel Welder................................................................................................................................................................................................. 187.30 - 17031
17032 Tiler............................................................................................................................................................................................................................... 139.20 97.40 17032
17033 Window Frame Installer................................................................................................................................................................................................ 140.70 98.50 17033
17034 Asbestos Abatement Worker......................................................................................................................................................................................... 151.90 - 17034
17035 Paving Block Layer....................................................................................................................................................................................................... 129.80 - 17035
BUILDING SERVICES INSTALLATION Registered Worker
(for designated
trade)
Semi-
Skilled
skilled
Worker
Worker
A B
Per hour $ $
17036 Electrical Fitter.............................................................................................................................................................................................................. 113.10 - 17036
17037 Control Panel Assembler.............................................................................................................................................................................................. 135.80 95.00 17037
17038 Electrical Wireman........................................................................................................................................................................................................ 124.40 87.10 17038
17039 Fire Service Mechanic................................................................................................................................................................................................... 113.20 - 17039
17040 Fire Service Fitter.......................................................................................................................................................................................................... 101.80 71.30 17040
17041 Mechanical Fitter........................................................................................................................................................................................................... 105.30 73.70 17041
17042 Refrigeration / Air-conditioning / Ventilation Mechanic............................................................................................................................................. 100.20 70.20 17042
17043 Building Security System Mechanic............................................................................................................................................................................. 137.50 96.30 17043
17044 Communication System Mechanic............................................................................................................................................................................... 131.60 92.10 17044
17045 Gas Installer................................................................................................................................................................................................................... 119.20 - 17045
17/6
17 LABOUR 17
Item Item
LABOUR (CONT'D)
GENERAL
A
Per hour $
17046 Registered General Worker............................................................................................................................................................................................................. 101.20 17046
17047 Security guard.................................................................................................................................................................................................................................. 42.30 17047
SPECIAL ATTENDANCE ON BUILDING WORKS AND ON BUILDING SERVICES INSTALLATION
A
Per hour $
17048 Registered General Worker for attending Building Works............................................................................................................................................................ 101.20 17048
17049 Registered Electrical Fitter for attending Building Services Installation...................................................................................................................................... 119.60 17049
17/7
Section 18
TEMPORARY PLANT AND FACILITIES
18 TEMPORARY PLANT AND FACILITIES 18
SECTION 18
TEMPORARY PLANT AND FACILITIES
SPECIAL CONDITIONS
TEMPORARY PLANT
Measurement of SC18.01 Temporary plant shall include the provision of plant and machineries like air compressors,
temporary vans, lorries, excavator, skid steer loaders, cranes, mobile access platforms, generator
plant sets, pumps, etc. measured in this Section of the Schedule.
Wherever possible, work executed under the Contract shall be measured and paid for at
the rates of the appropriate Section in this Schedule. No measurement shall be made for
temporary plant unless specifically ordered by the Maintenance Surveyor in writing.
The measurement of temporary plant shall be the aggregate time hired on the item of plant
to the nearest hour for any time in a 24-hour day (from 00:00 hour to 24:00 hour on the
same day) including all Sundays and General Holidays. No measurement shall be made for
standing time, mobilization and demobilization time. The minimum order for temporary
plant shall be calculated based on a minimum period of 8 hours in any one Works Order
which is to be confirmed by the Maintenance Surveyor in writing. The hiring of the
temporary plant shall be measured and valued based on the actual time of deployment of
the plant or based on a period of 8 hours, whichever is the higher.
Allowance for overtime work and any cost / expenses incurred therein is deemed to be
included in the Contract Percentage(s) applied to the Contract. Reference shall also be
made to General Regulations Clauses GR.04 and GR.12.
All temporary plant brought onto the Site shall be maintained in good operation condition.
Should the temporary plant provided to the Government break down or be found
unserviceable, no payment shall be made for replacement of the same.
Rates SC18.02 The rates shall generally include for : -
generally
(a) Mobilization and demobilization of all temporary plant to and from the Site.
(b) Plant operator (for excavator, skid steer loader, crane and access platform),
driver and attendant.
(c) Fuel, lubricants, consumable stores, maintenance and repair.
(d) Contractor's profit, establishment charges and overheads.
(e) Insurances, license fees, patent rights and royalties, where applicable.
(f) Moving from the designated location to new position as directed by the
Maintenance Surveyor.
(g) Lowering and hoisting including taking from or to any floor or roof of an existing
building or structure.
18/1
18 TEMPORARY PLANT AND FACILITIES 18
SPECIAL CONDITIONS
TEMPORARY PLANT
Rates SC18.02 (h) Loading and unloading.
generally (Cont'd)
(Cont'd) (i) Repairing and making good or replacing at the Maintenance Surveyor's discretion
any articles or materials damaged during moving, loading, transit, unloading, and
moving to new position, store or stack.
(j) All tunnel or bridge tolls.
TEMPORARY ACCOMMODATION
Measurement of SC18.03 Temporary accommodation shall include the provision of temporary container office and
temporary portable toilets which are for the exclusive use by the Employer and his staff.
accommodation
Throughout this Schedule, rates for all trades shall include for providing temporary offices
and portable toilets as in G.S. Item 1.28 for the period of uses throughout the Works
Order period. No payment will be made for providing and maintenance of container
office and portable toilets under any circumstances, except for the following ordered by
the Maintenance Surveyor specifically in writing : -
(a) Temporary container office and portable toilets for the exclusive use by the
Employer and his staff.
Rates for SC18.04 The rates for temporary container office shall include for : -
temporary
container (a) Mobilization and demobilization of temporary container office.
office
(b) Fitting out with internal finishes complete with door, windows, lighting, power
socket and room cooler (power supply measured separately).
Internal finishes shall be as follows : -
(i) Walls - painted or plastic veneered plywood including insulation.
(ii) Ceiling - painted or acoustic tiles with insulation.
(iii) Floors - PVC floor tiles or sheeting.
(c) Provision of adequate lighting, air-conditioning and ventilation including payment
of all charges.
(d) Forming and levelling ground for resting of container office.
(e) Providing MCB board for electricity supply connection.
Rates for SC18.05 The rates for portable toilet shall include for : -
portable
toilet (a) Mobilization and demobilization of portable toilet.
(b) Regularly pumping, desludging and clearing away soil and waste.
18/2
18 TEMPORARY PLANT AND FACILITIES 18
SPECIAL CONDITIONS
TEMPORARY ACCOMMODATION
Rates for SC18.05 (c) Cleaning and sanitizing the interior and exterior of the portable toilet to ensure that
portable (Cont'd) the portable toilet is always kept clean, tidy and hygienic including cleaning and
toilet sanitizing as directed by the Maintenance Surveyor.
(Cont'd)
(d) Filling and regularly re-filling flushing water, fresh water and toilet paper and
maintaining water and toilet paper available at all times.
(e) Re-charging deodorizer when required.
(f) Replacement of portable toilet which is not serviceable.
(g) Forming and levelling ground for resting of portable toilets.
(h) Reinstatement and making good surfaces disturbed at demobilization.
(i) Government dumping charges.
CONVEYANCE BY LAND VEHICLE
Measurement SC18.06 Conveyance of articles or materials by land vehicle shall only be measured where such
of conveyance conveyance is not included under any items in other Sections of this Schedule and is
of articles or specifically ordered in writing by the Maintenance Surveyor.
materials by
by land vehicle One trip is defined as the door-to-door conveyance of articles or materials from the
starting location to the last designated location which may include one or more interim
and/or designated stops.
Rates for SC18.07 The rates for conveyance of articles or materials by land vehicle shall generally include for :-
conveyance
of articles or (a) Conveyance of articles or materials inside and outside the Contract areas.
materials
by land vehicle (b) Moving from the designated location to new position as directed by the
Maintenance Surveyor.
(c) Lowering and hoisting including taking from or to any floor or roof of an existing
building or structure.
(d) Loading and unloading.
(e) Transporting to and return journey of packing and personnel as required.
(f) Neatly stacking, storing or leaving in the required new position.
(g) Provision of driver and all labour, tools and plant necessary including levers,
ropes, planks, rollers, wheelbarrows, trucks, lorries and the like.
18/3
18 TEMPORARY PLANT AND FACILITIES 18
SPECIAL CONDITIONS
CONVEYANCE BY LAND VEHICLE
Rates for SC18.07 (h) Provision of any necessary temporary packing, securing ropes and the like, and
conveyance (Cont'd) properly securing and keeping the articles or materials secured during transit.
of articles or
materials (i) Repairing and making good or replacing at the Maintenance Surveyor's discretion
by land vehicle any articles or materials damaged during moving, loading, transit, unloading, and
(Cont'd) moving to new position, store or stack.
(j) All tunnel or bridge tolls.
(k) All costs in respect of loading, unloading and delivery of articles or materials from
and to remote area where no vehicular access is available.
(l) Dismantling and reassembling composite articles, if required.
(m) Obtaining access licenses and permits.
(n) Insurance of all materials or articles being conveyed and supervising staff on
board.
CONVEYANCE BY HELICOPTER
Measurement SC18.08 Conveyance of articles or materials by helicopter shall only be measured where such
of conveyance conveyance is not included under any items in other Sections of this Schedule and is
of articles or specifically ordered in writing by the Maintenance Surveyor.
materials by
helicopter One trip is defined as the conveyance of articles and materials from the time when the
helicopter leaves the flying base to the time when it lands at the flying base. The helicopter
shall be fuelled adequately for any flights over 90 minutes before it flies. No measurement
shall be made for any time required for first fuelling. However, when a flight exceeds 90
minutes and where no access can be provided for the re-fuelling vehicle to the designated
locations for loading or unloading, the time for re-fuelling to and from the flying base shall
also be measured.
Conveyance by helicopter for the first 30 minutes shall be measured per trip. Conveyance
after the first 30 minutes shall be measured to the nearest 5 minutes.
Rates for SC18.09 The rates for conveyance by helicopter shall include for : -
conveyance
of articles or (a) Lowering to and hoisting from the designated locations for loading or unloading.
materials by
helicopter (b) Provision of pilot and lifting equipment certified by an independent specialist.
(c) Provision of any necessary temporary packing, securing ropes and the like, and
properly securing and keeping the articles or materials secured during transit.
(d) Insurance of all materials or articles being conveyed and supervising staff on
board.
18/4
18 TEMPORARY PLANT AND FACILITIES 18
SPECIAL CONDITIONS
CONVEYANCE BY HELICOPTER
Rates for SC18.09 (e) Training course at the flying base for the Employer's ground crew for loading and
conveyance (Cont'd) unloading.
of articles or
materials by (f) A loadmaster at the designated location for loading where the helicopter can land
helicopter nearby.
(Cont'd)
(g) Radio communication between the loadmaster and the pilot where load master is
provided.
(h) Any advance payment made to the specialist helicopter conveyance company.
SCAFFOLDING, SCREENS AND STAGING
Scaffolding, SC18.10 Throughout this Schedule, rates for all trades shall include for use and waste of all types of
screens and scaffolding and staging for the execution of the Works. No payment will be made for
staging scaffolding and staging under any circumstances except for the following : -
generally
(a) Scaffolding and staging are specifically ordered by the Maintenance Surveyor in
writing and stating that the scaffolding and staging are for the exclusive use of the
Maintenance Surveyor for carrying out design inspections or the exclusive use of
the Employer and other contractor employed by the Employer within the Works
Order period.
In the event where the scaffolding and staging mentioned in sub-clause (a) above are
subsequently used by the Contractor himself, no payment will be made.
Similarly, rates for all trades shall include for screens covering up and protecting works
from damage caused by dust, sun, rain and similar hazards, and protecting the public from
dust, nuisance, falling rubbish and the like.
No payment will be made for screens under any circumstance except where specifically
ordered by the Maintenance Surveyor in writing and stating that they are for the exclusive
use of the Employer.
Measurement SC18.11 Scaffolding shall be measured net face area as erected between the two outmost uprights
of scaffolding of the scaffolding. The height of the scaffolding shall be measured from the average
founding levels to the top continuous effective horizontal rails. No deduction for opening
shall be made.
Measurement SC18.12 Extra over for screens fixed to scaffolding shall be measured net to the areas as fixed.
of Extra over No deduction shall be made for opening not exceeding 2.00 m.
for screens
Measurement SC18.13 Tower scaffolding of any form shall be measured net volume based on net plan area as
of tower erected between the outmost supporting members of the scaffolding and the height of the
scaffolding top member of the scaffolding.
18/5
18 TEMPORARY PLANT AND FACILITIES 18
SPECIAL CONDITIONS
SCAFFOLDING, SCREENS AND STAGING
Measurement SC18.14 Staging to soffits of building or structure shall be measured net plan area as erected
of staging between the outmost supporting members of the staging. The height of the staging shall be
measured from the working platform to the average founding level where it is erected. No
deduction shall be made for opening not exceeding 1.00 m.
Rates for SC18.15 The rates for scaffolding shall generally include for : -
scaffolding
generally (a) Provision and erection on Site of all materials including poles, uprights, rails,
bracings, etc., timber, lashings, struts, wedges, boarding, toe boards, spikes,
screws, bolts, straps, brackets, clamps and the like and any safety nettings, safety
fans, sloping catch fans, protective canopy all as specified in the Specification in
the Contract.
(b) Making good any damage caused to walls and other surfaces during use, erection
and taking down.
(c) Repairing and maintaining throughout the period of use in first or subsequent
positions. Providing all necessary inspection report(s) as required by the
Construction Site (Safety) Regulations.
(d) Complying with codes and standards of G.S. Items 1.34 and 1.39.1 to 1.39.8.
(e) Certification by Authorized Persons or Registered Structural Engineers.
Rates for metal SC18.16 The rates for metal scaffolding shall further include for : -
scaffolding
(a) Delivery to and erection on Site, repairing and maintaining throughout the period
of use in first or subsequent positions and taking down and setting aside for
re-erection or removing from Site.
(b) Proprietary or non-proprietary type.
(c) Providing and assembling all materials including poles, rails, supports, struts,
ladders, bracings, working platform and any other accessories in accordance with
the recommendations of the system.
Rates for SC18.17 The rates for Extra over for screens shall include for : -
Extra over
for screens (a) Providing and fixing screens to scaffolding, repairing and maintaining throughout
the period of use in first or subsequent positions and taking down and setting
aside for re-erection or removing from Site.
(b) All fixing accessories.
(c) Sealing up joints, forming opening and finishing any portion as doors or flaps.
(d) Allowing for laps.
(e) Making good any damage caused during use, erection and taking down.
18/6
18 TEMPORARY PLANT AND FACILITIES 18
SPECIAL CONDITIONS
SCAFFOLDING, SCREENS AND STAGING
Rates for staging SC18.18 The rates for staging shall include for : -
(a) Delivery to and erection on Site, repairing and maintaining throughout the period
of use in first or subsequent positions, and taking down and setting aside for
re-erection or removing from Site.
(b) Providing and assembling all materials including poles, rails, supports, struts,
ladders, bracings, working platform, swivel casters with brake, jack base and any
other accessories to support any imposed loads in accordance with the
recommendations of the staging.
(c) Proprietary or non-proprietary type.
(d) Making good any damage during use including replacement if required.
(e) Allowance for ensuring no overloading the staging.
18/7
18 TEMPORARY PLANT AND FACILITIES 18
Item Item
TEMPORARY PLANT
A
Per hour $
18001 Air compressor, silenced machine (3.0 m/min. at 7 kg/cm) with two 15 m hoses and two breakers 187.10 18001
including one operator for compressor...........................................................................................................................................................................................
18002 Ditto, (6.0 m/min. at 7 kg/cm) with four 15 m hoses and four breakers including one operator for compressor...................................................................... 341.90 18002
18003 Excavator, full circle slew crawler or wheel mounted with backacter, 6 tonnes........................................................................................................................... 465.90 18003
18004 Skid steer loader, rated operating capacity up to 620 kg................................................................................................................................................................ 337.70 18004
18005 Crane, lorry mounted or all terrain, n.e. 12 tonnes......................................................................................................................................................................... 806.80 18005
18006 Ditto, up to 20 tonnes...................................................................................................................................................................................................................... 964.80 18006
18007 Ditto, up to 30 tonnes...................................................................................................................................................................................................................... 1,162.30 18007
18008 Access platform, scissor lift self propelled, yard travel, capacity up to 400 kg............................................................................................................................. 258.00 18008
18009 Ditto, up to 800 kg.......................................................................................................................................................................................................................... 314.60 18009
18010 Ditto, exceeding 800 kg.................................................................................................................................................................................................................. 346.80 18010
18011 Access platform, telescopic self propelled, yard travel, capacity up to 400 kg and platform height up to 10.0 metre................................................................ 689.90 18011
18012 Ditto, capacity up to 400 kg and platform height exceeding 10.0 metre....................................................................................................................................... 893.20 18012
18013 Access platform, vehicle mounted, telescopic/articulated in any capacity and platform height up to 20.0 metre....................................................................... 767.30 18013
18014 Ditto, platform height up to 30.0 metre.......................................................................................................................................................................................... 803.10 18014
18015 Ditto, platform height exceeding 30.0 metre.................................................................................................................................................................................. 2,385.50 18015
18016 Generator set, 330.0 kVA............................................................................................................................................................................................................... 750.80 18016
18017 Pumps, portable, double diaphragm, discharge branch up to 51 mm diameter including hoses n.e. 100 metre long.................................................................. 86.10 18017
18018 Ditto, up to 102 mm diameter......................................................................................................................................................................................................... 115.30 18018
18019 Pumps, portable, sludge and sewage, discharge branch up to 102 mm diameter including hoses n.e. 100 metre long.............................................................. 133.50 18019
18020 Pumps, portable, electric submersible, discharge branch up to 51 mm diameter including hoses n.e. 100 metre long.............................................................. 79.70 18020
18021 Ditto, up to 102 mm diameter......................................................................................................................................................................................................... 107.90 18021
18/8
18 TEMPORARY PLANT AND FACILITIES 18
Item Item
TEMPORARY ACCOMMODATION
Temporary container office : -
A
Per month $
18022 Container office, 20 feet long......................................................................................................................................................................................................... 1,362.90 18022
Portable toilet : -
Per month
18023 Portable toilet equipped with open waste tank............................................................................................................................................................................... 2,146.00 18023
18024 Ditto but of handicapped type......................................................................................................................................................................................................... 2,713.90 18024
18025 Portable toilet equipped with flushing system............................................................................................................................................................................... 3,203.20 18025
18026 Portable toilet equipped with flushing system and wash hand basin............................................................................................................................................ 3,571.40 18026
CONVEYANCE BY LAND VEHICLE
A
Per trip $
18027 Van, pick up or similar utility vehicle, capacity up to 1.30 tonnes................................................................................................................................................ 191.20 18027
18028 Ditto but up to 2.60 tonnes............................................................................................................................................................................................................. 223.20 18028
18029 Lorry (highway use) n.e. 6.50 tonnes.............................................................................................................................................................................................. 303.80 18029
18030 Ditto but 12.00 tonnes..................................................................................................................................................................................................................... 335.00 18030
18031 Ditto but 24.50 tonnes..................................................................................................................................................................................................................... 416.40 18031
18032 Extra over either of Items 18029 to 18031 inclusive for lorry fitted with crane (jib arm) attachment, maximum load
n.e. 3.50 tonnes............................................................................................................................................................................................................................... 20.80 18032
18033 Ditto exceeding 3.50 tonnes............................................................................................................................................................................................................ 29.50 18033
18034 Lorry with tipper (highway use) n.e. 11.0 tonnes........................................................................................................................................................................... 335.00 18034
18/9
18 TEMPORARY PLANT AND FACILITIES 18
Item Item
CONVEYANCE BY HELICOPTER
A
Per trip $
18035 Helicopter, carrying capacity up to 800 kilogrammes, for the first 30 minutes............................................................................................................................. 18,480.00 18035
Each
18036 Add to Item 18035 for each subsequent 5 minutes (measured to the nearest 5 minutes)............................................................................................................. 3,080.00 18036
SCAFFOLDING AND SCREENS (OTHER THAN METAL SCAFFOLDING)
Erect, maintain, take down and clear away : -
A
Per square metre $
18037 Scaffolding comprising a single framework of uprights and horizontal rails................................................................................................................................ 33.20 18037
18038 Scaffolding comprising a double framework of uprights and horizontal rails of free standing scaffolding................................................................................. 42.70 18038
18039 Extra over either of Items 18037 to 18038 inclusive for providing screens of woven polyethylene sheet (nei lung tso pao),
tarpaulin or other suitable coverings............................................................................................................................................................................................... 20.10 18039
18040 Extra over either of Items 18037 to 18038 inclusive for providing safety net; one layer............................................................................................................. 13.30 18040
18041 Ditto; two layers.............................................................................................................................................................................................................................. 26.60 18041
18042 Blast or landslip protection screen constructed of steel framings closely erected, and braced and strutted at not
more than 1.20 m centres, or other approved construction covered with expanded metal or chain link mesh and
fixed screen including concrete footings or movable concrete blocks and make good after completion..................................................................................... 306.20 18042
18043 Woven polyethylene sheet (nei lung tso pao) or tarpaulin laid on slopes, etc. as protection including stakes, pegs,
bamboo supports, etc. as necessary................................................................................................................................................................................................ 20.30 18043
Per cubic metre
18044 Tower scaffolding........................................................................................................................................................................................................................... 112.70 18044
18/10
18 TEMPORARY PLANT AND FACILITIES 18
Item Item
METAL SCAFFOLDING AND SCREENS
Erect, maintain, take down and clear away : -
A
Per square metre $
18045 Metal scaffolding comprising a single framework of uprights and horizontal rails...................................................................................................................... 100.20 18045
18046 Metal scaffolding comprising a double framework of uprights and horizontal rails of free standing scaffolding....................................................................... 133.60 18046
18047 Extra over either of Items 18045 to 18046 inclusive for providing screens of woven polyethylene sheet, tarpaulin or other
suitable coverings recommended by the system............................................................................................................................................................................. 20.10 18047
18048 Extra over either of Items 18045 to 18046 inclusive for providing safety net; one layer............................................................................................................. 13.50 18048
18049 Extra over either of Items 18045 to 18046 inclusive for providing safety net; two layers............................................................................................................ 27.10 18049
Per cubic metre
18050 Tower scaffolding........................................................................................................................................................................................................................... 496.50 18050
STAGING
Erect, maintain, take down and clear away : -
A
Per square metre $
18051 Metal staging n.e. 4.00 m high........................................................................................................................................................................................................ 147.20 18051
18052 Ditto 4.00 - 8.00 m high.................................................................................................................................................................................................................. 168.20 18052
18053 Ditto 8.00 - 11.00 m high................................................................................................................................................................................................................ 238.30 18053
18054 Ditto 11.00 - 15.00 m high.............................................................................................................................................................................................................. 308.40 18054
18055 Ditto 15.00 - 19.00 m high.............................................................................................................................................................................................................. 378.50 18055
18/11
Section 19
RECREATIONAL / SPORTS SURFACING AND
PROTECTIVE PADDING
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
SECTION 19
RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING
SPECIAL CONDITIONS
Measurement SC19.01 All items of surfacing/flooring systems shall be measured over the net area covered
including additional girth of curbs, channels and the like. No deduction shall be made
for voids not exceeding 0.5 m.
Rubber protective padding shall be measured the net covered area as fixed.
Rates SC19.02 Unless otherwise stated, the rates shall generally include for supply and installation
generally complete including all necessary fixing accessories all in accordance with
manufacturer's instructions.
Rates for SC19.03 The rates for athletic track/sports floor surfacing, multi-sport surfacing and impact
athletic track / absorbing surfacing shall further include for : -
sports floor
surfacing, (a) All works to flat or sloping surfaces.
multi-sport
surfacing and (b) Laying to falls and currents.
impact
absorbing (c) All works to curve, circular and any shape required by the Maintenance
surfacing Surveyor.
(d) All necessary cleaning and preparation of new or existing substrate as
recommended by manufacturers prior to laying including application of
sealer.
(e) Working along perimeter or around obstructions.
(f) Laying to pattern if required.
(g) Provision of literature, test certificates, reports, maintenance manuals,
manufacturer's guarantee and supplier's / applicator's warranty.
(h) Provision of samples.
(i) Providing all shop drawings associated with builder work requirements.
(j) Providing deed of warranty when required.
19/1
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
SPECIAL CONDITIONS
Rates for SC19.04 The rates for provision of International Association of Athletics Federation's (IAAF)
provision of Certificate and report of measurement shall further include for : -
IAAF Certificate
and report of (a) Carrying out examination and survey by an approved independent specialist
measurement including labour, supervisory staff and equipment required.
(b) Provision of examination certificate and IAAF Certification System - Report
of Measurement.
Rates for SC19.05 The rates for protective padding shall further include for : -
protective
padding (a) Provision of samples.
(b) Covering material of outdoor usage which is capable to resist ultraviolet
degradation within the warranty period.
(c) Provision of literature, test certificates, reports, maintenance manuals,
manufacturer's guarantee and supplier's / applicator's warranty.
(d) Providing deed of warranty when required.
Rates for SC19.06 The rates for self-levelling semi-flexible screed shall further include for : -
self-levelling
semi-flexible (a) All preparation work to the existing proprietary recreational surface coating,
screed as recommended by the manufacturer, prior to applying the self-levelling
semi-flexible screed.
(b) Adopting screed compatible to the existing proprietary recreational surface
coating underneath.
(c) Provision of literature, test certificates, reports, maintenance manuals,
manufacturer's guarantee and supplier's / applicator's warranty.
19/2
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
SPECIAL CONDITIONS
Rates for SC19.07 The rates for recreational surface coating system shall further include for : -
recreational
surfaces (a) All preparation work to existing surfaces as recommended by the
coating manufacturer.
system
(b) Repairing minor cracks and voids to the substrate with approved proprietary
materials.
(c) Multi-coloured work and cutting to line.
(d) Keeping adjacent surfaces clean as G.S. Item 21.44 and painting surfaces
disturbed.
(e) Removing all articles of hardware and the like before painting and re-fixing
after painting has been completed.
(f) Painting sample panels as required.
(g) Touching up coated surfaces on completion as required.
(h) Protecting and cleaning as G.S. Item 21.43.
(i) Removing painted sample panels.
(j) Provision of literature, test certificates, reports, maintenance manuals,
manufacturer's guarantee and supplier's / applicator's warranty.
Rates for line SC19.08 The rates for line marking on recreational surfaces coating system shall further include
marking on for : -
recreational
surfaces (a) All preparation work to existing surfaces as recommended by the
coating system manufacturer.
(b) Keeping adjacent surfaces clean as G.S. Item 21.44 and painting surfaces
disturbed.
(c) Removing all articles of hardware and the like before painting and re-fixing
after painting has been completed.
(d) Painting samples as required.
(e) Setting out and paint all courts to the required standards.
(f) Touching up coated surfaces on completion as required.
(g) Protecting and cleaning as G.S. Item 21.43.
(h) Provision of literature, test certificates, reports, maintenance manuals,
manufacturer's guarantee and supplier's / applicator's warranty.
19/3
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
ATHLETIC TRACK/SPORTS FLOOR SURFACING
Proprietary all weather athletic track/sports floor surfacing system on level or slope including applying by any means on
flexible sub-surfacing (measured separately), any preparation and protection works, fixing components and accessories,
making good and cleaning of affected areas on completion, all in accordance with manufacturer's instructions :
Take
Cast in-situ proprietary all weather sports floor surfacing system of high quality, stable and environmental friendly Supply down
materials suitable for playgrounds and ball games and complying with the following : - and and
fix clear
away
A B
Per square metre $ $
Construction Seamless
Cast in-situ all in accordance with manufacturer's instructions
System Single layer permeable system comprising of Proprietary materials mixed with EPDM
granules of 1 mm to 3 mm grain size using proprietary binder to give a textured finish
Surface colour Uniform and oxide-red in colour
Textured surface Flat texture, porous
Joints Shall not occur at points of intense wear
Joints between Shall be carefully set out to coincide with subsequent line making
bays
Conditions Requirements
Force reduction Between 10 and 40 35% to 50%
Modified vertical deformation Between 10 and 40 0.6 mm to 2.2 mm
Friction (Sliding coefficient) Wet, leather test sole 0.5 (DIN method)
47 (TRRL method)
Tensile properties Tensile strength 0.4 N/mm2
Elongation at break 40 %
Standard deformation Between 0 and 40 0.6 mm to 1.8 mm
Relative abrasion 1.0
Spike resistance Class 1 to DIN V 18035-6
Remaining indentation 1.0 mm
Ageing Constant climate with pass to DIN V 18035-6
condensation
Constant heat (80)
Combined climate of
heat, humidity and light
Environmental compatibility to DIN V 18035-6
19001 Proprietary all weather sports floor surfacing system, overall finished thickness 5 mm to 10 mm............................................................................ 256.40 41.50 19001
19002 Ditto but 10 mm to 15 mm thick................................................................................................................................................................................... 447.20 47.20 19002
19/4
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
ATHLETIC TRACK/SPORTS FLOOR SURFACING (CONT'D)
Proprietary all weather athletic track/sports floor surfacing system on level or slope including applying by any means on
flexible sub-surfacing (measured separately), any preparation and protection works, fixing components and accessories,
making good and cleaning of affected areas on completion, all in accordance with manufacturer's instructions : (Cont'd)
Take
Cast in-situ proprietary all weather athletic track surfacing system of high quality, stable and environmental friendly materials Supply down
suitable for athletic tracks for athletic competition and complying with relevant IAAF standards and the following : - and and
fix clear
away
A B
Per square metre $ $
Construction Seamless
Cast in-situ all in accordance with manufacturer's instructions
System Full pour system comprising :
a) 1st layer and 2nd Proprietary full depth PUR coating materials mixed with
layer embedded black recycled rubber granules (compact and
foamy) of 1 mm to 4 mm grain size using proprietary
binder
b) 3rd layer Proprietary full depth PUR materials with broadcast
EPDM granules of 1 mm to 4 mm grain size using
proprietary binder to give a textured finish, overall
finished thickness 3.5 mm
Surface colour Uniform and red-brown in colour
Textured surface Granular texture
Joints Shall not occur at points of intense wear
Joints between Shall be carefully set out to coincide with subsequent line making
bays
Conditions Requirements
Force reduction Between 10 and 40 35% to 50%
Modified vertical deformation Between 10 and 40 0.6 mm to 2.2 mm
Friction (Sliding coefficient) Wet, leather test sole 0.5 (DIN method)
47 (TRRL method)
Tensile properties Tensile strength 0.5 N/mm2
Elongation at break 40 %
19003 Proprietary all weather athletic track surfacing system, overall finished thickness 5 mm to 10 mm......................................................................... 377.90 47.20 19003
19004 Ditto but 10 mm to 15 mm thick................................................................................................................................................................................... 661.50 52.30 19004
19/5
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
ATHLETIC TRACK/SPORTS FLOOR SURFACING (CONT'D)
Proprietary all weather athletic track/sports floor surfacing system on level or slope including applying by any means on
flexible sub-surfacing (measured separately), any preparation and protection works, fixing components and accessories,
making good and cleaning of affected areas on completion, all in accordance with manufacturer's instructions : (Cont'd)
Cast in-situ proprietary all weather athletic track surfacing system of high quality, stable and environmental friendly materials Take
suitable for running tracks for training purposes and complying with relevant IAAF and DIN 18035/6 standards and the Supply down
following : - and and
fix clear
away
A B
Per square metre $ $
Construction Seamless
Cast in-situ all in accordance with manufacturer's instructions
System Sandwich system comprising :
a) 1st layer Proprietary materials mixed with black recycled rubber
granules of 1 mm to 4 mm grain size using proprietary
binder and grouted with proprietary pore sealer
b) 2nd layer Proprietary materials mixed with EPDM granules of 1 mm
to 4 mm grain size using proprietary binder to give a
textured finish, overall finished thickness 3 mm
Surface colour Uniform and oxide-red in colour
Textured surface Granular texture
Joints Shall not occur at points of intense wear
Joints between Shall be carefully set out to coincide with subsequent line making
bays
Conditions Requirements
Force reduction Between 10 and 40 35% to 50%
Modified vertical deformation Between 10 and 40 0.6 mm to 2.2 mm
Friction (Sliding coefficient) Wet, leather test sole 0.5 (DIN method)
47 (TRRL method)
Tensile properties Tensile strength 0.5 N/mm2
Elongation at break 40 %
Standard deformation Between 0 and 40 0.6 mm to 1.8 mm
Relative abrasion 1.0
Spike resistance Class 1 at DIN V 18035-6
Remaining indentation 1.0 mm
Ageing Constant climate with pass to DIN V 18035-6
condensation
Constant heat (80)
Combined climate of
heat, humidity and light
Environmental compatibility to DIN V 18035-6
19005 Proprietary all weather athletic track surfacing system, overall finished thickness 5 mm to 10 mm......................................................................... 300.80 47.20 19005
19006 Ditto but 10 mm to 15 mm thick................................................................................................................................................................................... 490.50 52.30 19006
19/6
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
ATHLETIC TRACK/SPORTS FLOOR SURFACING (CONT'D)
Proprietary all weather athletic track/sports floor surfacing system on level or slope including applying by any means on
flexible sub-surfacing (measured separately), any preparation and protection works, fixing components and accessories,
making good and cleaning of affected areas on completion, all in accordance with manufacturer's instructions : (Cont'd)
Prepare and apply proprietary athletic track/sports floor surfacing line marking paint of any colour and thickness including
marking out, preparing surface, cleaning and making good in accordance with the manufacturer's recommendations : -
A
Per linear metre $
19007 Line n.e. 100 mm wide ................................................................................................................................................................................................................... 23.50 19007
Each
19008 Hurdle and relay position ............................................................................................................................................................................................................... 59.20 19008
19009 Letters, characters, logos, signs, etc. and the like n.e. 300 mm high ............................................................................................................................................ 72.00 19009
19010 Apply and obtain International Amateur Athletic Federation (IAAF) Certificate (except Class 1 Certificate) including
examination certificate and report of measurement for Certified Athletics Facilities................................................................................................................... 38,358.20 19010
19011 Apply and obtain IAAF Class 1 Certificate including examination certificate and report of measurement for Certified
Athletics Facilities........................................................................................................................................................................................................................... 20,400.00 19011
(The actual rate should be : $204,000.00 for Item 19011A)
(Note : - The above Items 19001 to 19011 inclusive will only be paid for if ordered in writing by the Maintenance
Surveyor.)
19/7
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
MULTI-SPORT SURFACING
Proprietary multi-sport surfacing system on level or slope complying with relevant standards including applying by any means on
concrete or flexible sub-surfacing (measured separately), any preparation and protection works, fixing components and accessories,
making good and cleaning of affected areas on completion, all in accordance with manufacturer's instructions :
Proprietary all weather synthetic pre-fabricated roll sheet sport surfacing system for
outdoor use composed of two separate layers with butt-joint system between rolled
Overall thickness of system (mm)
joints complying with the following : -
4 6 8 10 12 15
A B C D E F
Per square metre $ $ $ $ $ $
Top layer 2-component UV resistant polyurethane resin
bound colour Ethylene Propylene Diene Poly
Methylene granules in 4 mm thick in
pre-fabricated roll sheet form
Bottom layer Resin bound black rubber-shred in
prefabricated roll sheet form
Both layers Tested and complied with BS 7044 including
testing at the following :
- Netball rebound under both wet
and dry conditions
- Basketball rebound under both wet and dry
conditions
- Abrasion resistance to abrasive wheels
- Fatigue resistance
- Resistance to indentation
- Slip resistance
- Peel strength
19012 Proprietary all weather synthetic pre-fabricated
roll sheet sport surfacing system to floor or wall ................................................................................. 595.80 653.40 670.20 699.70 815.00 924.10 19012
19013 Take down and clear away proprietary all weather synthetic
pre-fabricated roll sheet sport surfacing system................................................................................... 14.00 20.40 27.40 35.00 41.50 49.10 19013
Supply
and
fix
A
Per linear metre $
19014 In-laid line marking on proprietary all weather synthetic pre-fabricated roll sheet sports surfacing, n.e. 100 mm wide ............................................................ 125.20 19014
Each
19015 In-laid number on proprietary all weather synthetic pre-fabricated roll sheet sports surfacing, size : 800 x 800 mm ................................................................ 788.10 19015
19016 Ditto logo, size : 1200 x 1200 mm ................................................................................................................................................................................................ 1,600.80 19016
19/8
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
MULTI-SPORT SURFACING (CONT'D)
Proprietary multi-sport surfacing system on level or slope complying with relevant standards including applying by any means on concrete or
flexible sub-surfacing (measured separately), any preparation and protection works, fixing components and accessories, making good
and cleaning of affected areas on completion, all in accordance with manufacturer's instructions : (Cont'd)
Proprietary rubber sport surfacing system for indoor use comprising roll sheet 80% recycled EPDM rubber Overall thickness of
complying with the following : - system (mm)
7-8 9 - 10
A B
Per square metre $ $
Test Method Requirement
Density n/a 1,000 kg/m3
Resilience DIN 18032 -2 49%
Tensile Strength DIN 18032 -2 1.39 N/mm2
Tear Strength ASTM D 624 9.7 N/mm
Taber Abrasion ASTM C504 0.53 gm
Shore Hardness A ASTM D2240 60
Remaining DIN 53960 0.07 mm
Indentation
Noise Absorption EN 20140/ISO 140 18 db [10mm]
Stainability ASTM D543-95
Alcohol No Change
Ammonia No Change
Flammability ASTM D2859 (Sport Use) Class 1
DIN 4102 B2
Smoke ASTM E662
Non Flamming Avg SMC n/a
Flamming Avg SMC n/a
AS 1530 3:1999
Smoke Developed Index [0-10] n/a
Slip Resistance AS/NZS 4596 : 1999
Static Coefficient ASTM D2047 -97
of Friction Dry > 1.2
Wet > 1.2
Thermal Stability ASTM C1026 -40 to -100
19017 Proprietary recycled rubber and synthetic EPDM rubber surfacing system to floor or wall ...................................................................................... 556.70 705.80 19017
19018 Take down and clear away proprietary recycled rubber and synthetic EPDM rubber surfacing system.................................................................... 27.40 41.50 19018
Supply
and
fix
A
Per linear metre $
19019 In-laid line marking on proprietary recycled rubber and synthetic EPDM rubber surfacing system, n.e. 100 mm wide ............................................................ 72.80 19019
Each
19020 In-laid number on proprietary recycled rubber and synthetic EPDM rubber surfacing system, size : 800 x 800 mm ................................................................ 1,309.80 19020
19021 Ditto logo, size : 1200 x 1200 mm ................................................................................................................................................................................................ 1,600.80 19021
19/9
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
IMPACT ABSORBING SURFACING FOR PLAYGROUND
Proprietary impact absorbing surfacing for playground laid on level or slope complying with the relevant British Standards including
all preparation and protection works, fixing components and accessories, making good and cleaning of affected areas on completion,
all in accordance with manufacturer's instructions, fixing by any means on tarmacadam or concrete sub-base and the like : -
(Note : - All impact absorbing surfacing having weight in dry not less than 10 kg/m shall be supported by
laboratory report and submitted to the Maintenance Surveyor for approval. )
A
Per square metre $
19022 Impact absorbing surfacing of any colour and size with surface impact attenuation of
critical fall height 1.00 m maximum fixed with any approved adhesive ...................................................................................................................................... 349.70 19022
19023 Ditto but with critical fall height 1.30 m maximum ...................................................................................................................................................................... 374.90 19023
19024 Ditto but with critical fall height 1.50 m maximum ...................................................................................................................................................................... 476.10 19024
19025 Ditto but with critical fall height 2.00 m maximum ...................................................................................................................................................................... 576.70 19025
19026 Ditto but with critical fall height 3.00 m maximum ...................................................................................................................................................................... 814.30 19026
19027 Take down and clear away impact absorbing surfacing for either of Items 19022 to 19026 inclusive ....................................................................................... 14.60 19027
19028 Take down and set aside for reuse impact absorbing surface ditto ............................................................................................................................................... 46.80 19028
19029 Fix only impact absorbing surface ditto ......................................................................................................................................................................................... 63.30 19029
Per linear metre
19030 Triangular kerb margin for critical fall height 1.00 m maximum ................................................................................................................................................. 171.10 19030
19031 Ditto but with critical fall height 1.30 m maximum ...................................................................................................................................................................... 186.70 19031
19032 Ditto but with critical fall height 1.50 m maximum ...................................................................................................................................................................... 233.10 19032
19033 Ditto but with critical fall height 2.00 m maximum ...................................................................................................................................................................... 302.20 19033
19034 Ditto but with critical fall height 3.00 m maximum ...................................................................................................................................................................... 434.90 19034
19035 Take down and clear away triangular kerb margin surface for either of Items 19030 to 19034 inclusive .................................................................................. 6.40 19035
19036 Take down and set aside for reuse triangular kerb margin ditto ................................................................................................................................................... 15.90 19036
19037 Fix only triangular kerb margin ditto ............................................................................................................................................................................................. 24.60 19037
Per set
19038 Extra over impact absorbing surfaces for stepping block 300 x 300 x 600 mm high .................................................................................................................. 1,018.90 19038
19/10
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
PROTECTIVE PADDING
Proprietary protective padding complying with the relevant British Standards, DIN Standards or other equivalent standards all
in accordance with manufacturer's instructions, bonding by any means to walls, columns, posts and the like :
Proprietary rubber protective padding with anti-ozonant additive complying Take Take
with the following : - Supply down down Fix
and and and set only
Colour Black fix clear aside for
Polymer type 95% natural rubber, resistant to abrasion, UV away re-use
light and ozone attack A B C D
Hardness/Durometer 38 IRHD $ $ $ $
Tensile strength 26.7 MPa or 3870 psi
Elongation at break 760%
Tension set 10%
Tear strength 40 N/mm
Resilience 83%
Specific gravity 0.98
Temperature range -40 to +75 (-40 to +167)
Abrasion resistant index 105 at DIN 53516
Per square metre
19039 Rubber protective padding with 6 mm thick to wall or column............................................................................................... 1,721.30 24.90 25.50 86.50 19039
19040 Ditto but 12 mm thick............................................................................................................................................................... 2,802.90 24.90 25.50 86.50 19040
19041 Rubber protective padding with 6 mm thick to post................................................................................................................ 1,807.30 24.90 25.50 86.50 19041
19042 Ditto but 12 mm thick............................................................................................................................................................... 2,877.40 24.90 25.50 86.50 19042
Proprietary protective padding for outdoor use comprising PVC coated fabric vinyl cover in any
colour and 30 mm thick foam complying with the following: -
Vinyl Matt finish
PVC coated Flame retardant to NFPA 701 and ULC S-109 large-scale
fabric test requirement capable to resist ultraviolet degradation
Foam Closed cell polyethylene
Water vapour diffusion-resistance factor to DIN 52615
Chemical and water resistance to ASTM 543-56T
Ozone resistance to ASTM D1171
Self-extinguished fire rating to BS 476 Part 7 Class 1-2
Per square metre
19043 Wall padding with 12 mm thick 100% recycled plastic backing board................................................................................... 3,027.00 24.90 25.50 86.50 19043
19044 Column padding ditto................................................................................................................................................................ 3,536.40 24.90 25.50 86.50 19044
19045 Post padding (without backing board)...................................................................................................................................... 2,864.50 24.90 25.50 86.50 19045
19/11
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
PROTECTIVE PADDING (CONT'D)
Proprietary protective padding complying with the relevant British Standards, DIN Standards or other equivalent standards all in
accordance with manufacturer's instructions, bonding by any means to walls, columns, posts and the like : (Cont'd)
Proprietary protective padding for indoor use comprising PVC coated fabric
vinyl cover in any colour and 60 mm thick foam complying with the following : - Take Take
Supply down down Fix
and and and set only
Vinyl Matt finish fix clear aside for
PVC coated fabric Flame retardant to NFPA 701 and ULC S-109 away re-use
large-scale test requirement A B C D
Foam Density minimum 58 kg/m3 $ $ $ $
Meet fire test B.S. 5852 : Part 2
Contains no Class I or II Ozone Depleting
Chemicals (ODC) as listed under the Clean Air
Act Amendments 1990
Per square metre
19046 Wall padding with 12 mm thick plywood backing board........................................................................................................ 1,695.40 24.90 25.50 86.50 19046
19047 Column padding ditto................................................................................................................................................................ 2,292.10 24.90 25.50 86.50 19047
19048 Post padding (without backing board)...................................................................................................................................... 1,650.30 24.90 25.50 86.50 19048
Proprietary padding; 22 mm overall thickness for indoor use; with the foam made of polyether and polyester granules, density
is approximately 240 kg/m3, the tensile strength (at break) is 100 kPa at minimum, elongation at break is at minimum of 35%, the
flame rate is less than 100 mm per minute according to FMVSS 302, the force absorption is in average rate of 61.74% according
to DIN 18032; covered with flame retardant vinyl in any colour (excluding plywood backing), the weight is about 625 g/m2, the
material composition is made up with about 86% PVC compound and about 14% PES, the leather has the flame retardant
property according to DIN 4102 Class B2 / DIN 53 438 and DIN EN 1021 part 1 and part 2, thickness is about 0.90 mm to 1.15 mm, Supply
the data on the tensile strength (at break) is 230 N / 5 cm; q 120 N / 5 cm and the tear strength is 20 N; q 10 N : - and
fix
A
Per square metre $
19049 Proprietary padding to wall............................................................................................................................................................................................................. 2,397.60 19049
19050 Ditto to column................................................................................................................................................................................................................................ 2,570.10 19050
Take down and clear away safety wall padding of any thickness including backing, if any : -
Per square metre
19051 Padding fixed to wall or column..................................................................................................................................................................................................... 25.50 19051
TREATMENT TO EXISTING RECREATIONAL SURFACE COATING
A
Per square metre $
19052 Semi-flexible self-smoothing screed consisting of a slurry of bitumen emulsion, mineral filler combined with resilient
resin and a resilient aggregate of thermosetting polymers to form a hybrid resin and flexi-aggregate coating, applied
on existing recreational surface coating ........................................................................................................................................................................................ 192.80 19052
19/12
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
RECREATIONAL SURFACE COATING SYSTEM
Proprietary recreational surface coating system suitable for ball courts, soccer pitches and recreational grounds and Supply
complying with the following : - and
fix
A
Per square metre $
Formation 100% Acrylic resin formulation
Materials and application American Sports Builders Association
certified by
Materials approved International Tennis Federation
and classification by
Pace rating Average 39.5
Texture surface Mat surface with silica sand topping
Surface tolerance 1.5 mm
Surface colour Uniform and in standard colour
Coefficient of friction 0.7 Standard test by ITF
accredited laboratory
Coefficient of restitution Average 0.82 according to test report
ITFCS/01/01-05-129
Accelerated weather resistance No cracking, no swelling and no peeling off for 5 years
Coefficient of abrasion resistance Between 0.06-0.1 Taber's test 1000
Density of liquid coating Average 9 lb/gallon Standard test method for
inks and related products to
D1475-98(2003)
Viscosity at 77 Average 100-120 Standard test method for pigment
content of water emulsion paints by
low-temperature ashing to D562-01
Flammability Non-flammable Standard test method for determining
limits of flammability of chemicals
elevated temperature and pressure to
E918-83(1999)
Flash point None Standard test method for flash point
and fire point of liquids by tag
open-cup apparatus to D1310-01
Incombustibility No smoke
19053 Proprietary recreational surface coating system comprising two coats of asphaltic emulsion mixed with silica sand as underlayer
and filler coat, four coats of cushion resilient layer as texturizing layer and two coats of acrylic colour coating as finishing coat
(overall thickness 1.5 mm) on asphaltic or tarmacadam surfaces ............................................................................................................................................ 183.10 19053
19054 Proprietary recreational surface coating system comprising two coats of proprietary asphaltic emulsion mixed with silica sand
as underlayer and filler coat, four coats of proprietary acrylic resurfacer mixed with silica sand as texturizing layer and two
coats of proprietary acrylic colour coating as finishing coat (overall thickness 1.0 mm) on asphaltic or tarmacadam surfaces ........................................... 137.80 19054
19/13
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
RECREATIONAL SURFACE COATING SYSTEM (CONT'D)
Proprietary recreational surface coating system suitable for ball courts, soccer pitches and recreational grounds and complying Supply
with the following : - (Cont'd) and
fix
A
Per square metre $
19055 Proprietary recreational surface coating system comprising two coats of proprietary acrylic patch binder mixed with cement
and silica sand as underlayer, two coats of proprietary concrete primer as adhesion promotor, two coats of acrylic resurfacer
mixed with cement and silica sand as texturizing layer and two coats of proprietary acrylic colour coating as finishing coat
(overall thickness 1.0 mm) on concrete or coated surfaces ...................................................................................................................................................... 165.90 19055
19056 Add to either of Items 19053 to 19055 inclusive for laying one layer of fibreglass membrane .................................................................................................. 31.30 19056
19057 One coat of proprietary asphaltic emulsion mixed with silica sand as underlayer and filler coat ............................................................................................... 14.30 19057
19058 One coat of proprietary concrete primer as adhesion promotor .................................................................................................................................................... 12.90 19058
19059 One coat of proprietary acrylic resurfacer mixed with silica sand as texturizing layer ................................................................................................................ 19.90 19059
19060 One coat of proprietary acrylic patch binder mixed with cement and silica sand as underlayer ................................................................................................. 23.30 19060
19061 One coat of proprietary cushion resilient layer as texturing layer ................................................................................................................................................. 24.50 19061
19062 One coat of proprietary acrylic colour coating as finishing coat ................................................................................................................................................... 24.00 19062
Per linear metre
19063 Two coats of proprietary line marking on proprietary recreational surface coating system n.e. 50 mm wide ............................................................................. 16.30 19063
19064 Ditto but circular-on-plan n.e. 10.0 m radius ................................................................................................................................................................................ 19.30 19064
19/14
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
RECREATIONAL SURFACE COATING SYSTEM (CONT'D)
Proprietary recreational surface coating system suitable for ball courts, soccer pitches and recreational grounds and Supply
complying with the following : - (Cont'd) and
fix
A
Per square metre $
System An acrylic coloured sports surfacing consisting of one proprietary 100%
acrylic emulsion primer coat mixed with fine silica sand, two proprietary
100% acrylic highly pigmented emulsion under coats mixed with fine silica
sand and one proprietary 100% acrylic highly pigmented emulsion top coat
mixed with fine silica sand applied all in accordance with manufacturer's
instructions
Asbestos free
Suitable for all climatic conditions
Stable and fade resistant
Glare free
Uniform surface texture and colour
Vibrant colours remaining true and vibrant for years
Formulated to fight off ultraviolet degradation
Strong resistance to cracks and splitting
Strong resistance to abrasion
Strength and consistent ball bounce
Overall nominal thickness 1.0 mm
Surface colour Uniform and in standard colour
Accelerated weather resistance No fading, no cracking, no peeling tested to ASTM G26
and no chalking
Abrasion resistance 50 mg tested to ASTM D-4060 for 1000
revolutions
Tensile strength 283 psi tested to ASTM C-190
19065 Proprietary recreational surface coating system ............................................................................................................................................................................ 127.70 19065
Per linear metre
19066 Two coats of proprietary line marking on proprietary recreational surface coating system n.e. 50 mm wide ............................................................................. 49.80 19066
19067 Ditto but circular-on-plan n.e. 10.0 m radius ................................................................................................................................................................................ 53.80 19067
19/15
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
RECREATIONAL SURFACE COATING SYSTEM (CONT'D)
Proprietary recreational surface coating system suitable for ball courts, soccer pitches and recreational grounds and Supply
complying with the following : - (Cont'd) and
fix
A
Per square metre $
System A mineral based finish of inorganic nature consisting of
one proprietary primer coat, two proprietary under-coats
mixed with fine silica sand and one proprietary top coat
applied all in accordance with manufacturer's instructions.
Overall nominal thickness 1.0 mm
Surface colour Uniform and in standard colour
Air permeability 380 g/m2/24 hours tested to Japanese Industrial
Air permeability Standard Z0208
Coefficient of skid resistance 0.9 in dry condition tested to JIS A1407
0.9 in wet condition
Adhesion 24.5 kgf/cm2 at standard condition tested to 6.10 of JIS A6909
22.4 kgf/cm2 when immersed in
water
Abrasion resistance 0.15 mm tested to JIS K7204
Taber's test 1000 rotations
Accelerated weather resistance No change tested to 5.8 of JIS A6909
WS type, 2000 hours
Water resistance No swelling and no peeling tested to 6.8 of JIS K5668, 2 years
Cleaning resistance No breathing, no wear and no tear tested to 6.10 of JIS K5668,
1000 times
Gasoline resistance No change tested to 7.7 of JIS K5400
Freeze-thaw resistance No change tested to JIS A6910, 20 cycles
Incombustibility Pass JIS A1321 flame proof test
Building Ministry notice no.
1828 for incombustibility
Acid resistance No change tested with Citric acid (pH4)
at 60 for 7 days
Alkali resistance No change tested to 6.9 of JIS K5668, 1 month
Salt water resistance No change tested with 3 % salt water at room
temperature for 3 months
19068 Proprietary recreational surface coating system ............................................................................................................................................................................ 256.10 19068
Per linear metre
19069 Two coats of proprietary line marking on proprietary recreational surface coating system n.e. 50 mm wide ............................................................................. 49.50 19069
19070 Ditto but circular-on-plan n.e. 10.0 m radius ................................................................................................................................................................................ 53.80 19070
19/16
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
RECREATIONAL SURFACE COATING SYSTEM (CONT'D)
Proprietary recreational surface coating system suitable for ball courts, soccer pitches and recreational grounds and complying with
the following : - (Cont'd)
System Inorganic colour coating consisting of one proprietary bonding primer coat,
two proprietary under-coats mixed with fine silica sand and one proprietary
top coat applied all in accordance with manufacturer's instructions
Overall nominal thickness 1.0 mm
Surface colour Uniform and in standard colour
Textured surface Mat texture
Air permeability 250 g/m2/24 hours tested to JIS Z0208
Coefficient of skid resistance 0.9 in dry condition tested to JIS A1407
0.9 in wet condition
Adhesion 25 kgf/cm2 tested to 5.5 of JIS A6909
Coefficient of abrasion resistance Between 0.05 and 0.1 Taber's test CS-17.1kg, 1000 rotations
Shore hardness 97 Shore hardness meter
Accelerated weather resistance No cracking, no swelling, no peeling tested to 5.8 of JIS A6909, 2000 hours
off and no efflorescence
No substantial colour changed
compared with the test pieces not
exposed to the test
Wear resistance Wear loss 19 mg tested to 5.9 of JIS K5665, 1000 cycles
Weather resistance No problem outdoor exposure for 5 years
Water resistance No swelling and no peeling tested to 6.8 of JIS K5668, 1 year
Washing durability No tear and no wear tested to 6.10 of JIS K5668, 1000 times
Resistance against volatile oils : tested to 7.7 of JIS K5400
(a) No. 1 : Petroleum benzine 10 No wrinkling, no cracking and no
+ Toluene 0 peeling-off
(b) No. 2 : Petroleum benzine 9 Compared with the test pieces not
+ Toluene 1 subject to the test, not much change
in gloss, colour, adhesion and
hardness
(c) No. 3 : Petroleum benzine 8 Test liquid slightly less clear
+ Toluene 2
Freeze-thaw resistance Normal 5 hours at 20x 4 hours in water
x 15 hours at room temperature, 10 cycles
Incombustibility Pass : No smoke produced, no Building Authority notice no. 3 for
cracking and no peeling-off incombustibility test
Alkali resistance No cracking, no peeling-off, tested to 6.9 of JIS K5668, 1 month
no holes and no melting
Compared with the test
pieces not submerged in the
test liquid, no substantial
change in colour and gloss
Colour stability No efflorescence and no substantial tested to 6.4 of JIS K5400
colour change
Saline water resistance No abnormality Submerged in 5 % saline water for one month
Supply
and
fix
A
Per square metre $
19071 Proprietary recreational surface coating system ............................................................................................................................................................................ 182.60 19071
Per linear metre
19072 Two coats of proprietary line marking on proprietary recreational surface coating system n.e. 50 mm wide ............................................................................. 37.10 19072
19073 Ditto but circular-on-plan n.e. 10.0 m radius ................................................................................................................................................................................ 38.90 19073
19/17
19 RECREATIONAL / SPORTS SURFACING AND PROTECTIVE PADDING 19
Item Item
RECREATIONAL SURFACE COATING SYSTEM (CONT'D)
Proprietary recreational surface coating system suitable for ball courts, soccer pitches and recreational grounds and complying
with the following : - (Cont'd)
System 4" minimum thick compacted base course, 1 1/2" minimum compacted asphalt levelling
course (when required), 1" minimum compacted asphalt surface course on well
compacted and tested subgrade
Fall of the court Not less than 0.833% and not more than 1% Supply
and
fix
A
Per square metre $
19074 Proprietary tennis court surfacing system comprising two coats of acrylic resurfacer mix of surface filler coat, two coats of proprietary
acrylic textured coating with one coat of proprietary dilution agent as finishing coat on aspaltic or tarmacadam surfaces........................................................ 215.10 19074
Per linear metre
19075 Two coats of proprietary line marking on proprietary recreational surface coating system n.e. 50 mm wide ............................................................................. 43.20 19075
19076 Ditto but circular-on-plan n.e. 10.0 m radius ................................................................................................................................................................................ 46.40 19076
19/18
Section 20
FIXTURES AND FITTINGS
20 FIXTURES AND FITTINGS 20
SECTION 20
FIXTURES AND FITTINGS
SPECIAL CONDITIONS
Measurement SC20.01 This Section of the Schedule contains composite units of which the whole or majority
of joinery of the whole units are fabricated off-Site, delivered and assembled on Site.
fittings
All composite units shall be measured as finished work in place.
Unless otherwise stated, all sizes stated are finished sizes.
The rates appearing in this Section shall solely be applied to the valuation of fixtures
and fittings as composite units. Unless with the written approval of the Maintenance
Surveyor, composite units shall be measured as a whole unit and shall not be broken
down and measured as constituent components.
Rates for constituent components of the composite units in other Sections in the
Schedule of Rates shall not be permitted to apply to the valuation of the same, and
vice versa.
Unless otherwise stated, ironmongeries, hardware and all fixing accessories for joinery
fittings are deemed to be included in the rates of the joinery fittings and shall not
be measured separately.
No deduction shall be made for openings not exceeding 0.50 m2.
Measurement SC20.02 Drawer units, solid timber doors or sliding doors, shelving units and the like forming
of cabinets, part of the cabinets, cupboards, wardrobes, sink cabinets and the like shall not be
cupboards, measured separately but shall be deemed included as part of the whole joinery fittings.
wardrobes,
sink cabinets Glazed doors or glazed sliding doors are measured separately.
and the like
Measurement SC20.03 Book shelves, storage shelves, rack units and the like complete with side and back
of book shelves, panels, are composite units and are measured using rates in this Section of the Schedule.
storage shelves,
rack units and Shelving boards to open shelves without side and back panels shall not be measured
the like using rates in this Section, but shall be measured using rates in Section 08 - Carpentry
and Joinery of the Schedule.
Measurement SC20.04 Sunblinds shall generally be measured to the exact dimensions of the windows to be
of sunblinds, blinded.
curtains,
awnings and Curtains shall generally be measured the area to be curtained.
canvas generally
Awnings shall be measured to the net plan areas as fixed. Portion operating individually is
considered as one individual size.
20/1
20 FIXTURES AND FITTINGS 20
SPECIAL CONDITIONS
Measurement SC20.04 Canvas shall be measured to the net area as finished with no allowance made for
of sunblinds, (Cont'd) seams and pleats.
curtains,
awnings and Take down existing fixtures and power supply installation will be measured separately.
canvas generally
(Cont'd)
Rates for SC20.05 The rates for joinery fittings shall generally include for : -
joinery fittings
generally (a) Submission of design and shop drawings to be approved by the Maintenance
Surveyor.
(b) Submission of samples of components, colour samples, colour charts and the
like, for selection and consideration by the Maintenance Surveyor.
(c) Provision of prototypes for repetitive fittings, as required, to be approved by
the Maintenance Surveyor prior to fabrication.
(d) All fabrication, assembling and erection work either carried out on Site or off-Site.
(e) Installation and fixing work at any positions or heights and irrespective of
whether to existing or new surface.
(f) Materials used for framing construction shall include hardwood, softwood,
composite board or tropical hardwood substitute.
(g) All necessary treatment to all timber works.
(h) Any number of drawer units, shelving units and/or divisional panels as required.
(i) All surface finishes such as wax polished and/or painting with low VOC paint,
and/or laminated plastic veneer, unless otherwise specified.
(j) Where hardwood or timber veneer is specified as the surface finishes, the
veneer shall include the use of oak, maple, teak, beech, mahogany, cherry,
walnut, ash, anigre, citron, sapele or sycamore veneer.
(k) Lipping on all edges with selected hardwood.
(l) Forming tongued angles, chamfers, rebates, grooves and the like.
(m) Forming all types of framed joints including ship-lap, mitred, tenons, housed
dovetailed and the like.
(n) All ancillary materials for jointing and fixing accessories like metal brackets,
framing, bolts, nuts, etc. for installation and fixing in position.
(o) Ironmongery and hardware like hinges, catches, drawer runners, pull handles,
stud pins, locks and keys and the like.
(p) Pointing, jointing and sealing all edges.
20/2
20 FIXTURES AND FITTINGS 20
SPECIAL CONDITIONS
Rates for SC20.05 (q) Forming holes and recesses for toilet fittings, light fittings, sockets, accessories,
joinery fittings (Cont'd) etc. and/or pipework.
generally (Cont'd)
(r) Providing and maintaining suitable protective covering during progress of work and
removal of the same and leaving the joinery fittings clean upon completion of works.
(s) Making good all existing surfaces.
Rates for SC20.06 The rates for cabinets, cupboards, hanging cupboards, wardrobes and the like, shall
cabinets, further include for : -
cupboards,
hanging (a) Solid timber doors or sliding doors.
cupboards
wardrobes and (b) Where glazed doors or sliding glazed doors are specified, the panels shall be
the like constructed either in laminated glass or polycarbonate sheet complete with
glazing beads.
(c) Where sliding doors are specified, they should be fitted with tracks and rollers.
(d) Drawer units and shelving units forming part of the cabinets, cupboards, hanging
cupboards, wardrobes and the like.
(e) Hanging rods within wardrobes.
(f) Fixing to wall and ceiling including anchor bolts and stainless steel support brackets.
Rates for SC20.07 The rates for sink cabinets shall further include for : -
sink cabinets
(a) Under-sink cabinet either with fixed panels, door or sliding door panels.
(b) Drawer units and shelving units forming part of the sink cabinets.
(c) Forming or cutting opening to accommodate sink (measured separately).
(d) Fitting and installing sink (measured separately) and making all necessary adjustment
to suit.
(e) Pointing edges of the sink and tap with waterproof sealant.
Rates for SC20.08 The rates for pigeon hole racks shall further include for : -
pigeon hole
racks (a) Any number of pigeon holes as required.
Rates for SC20.09 The rates for proprietary fume cupboards shall include for : -
proprietary
fume cupboards (a) Design, supply, fabrication and installation of the complete system all in
accordance with the manufacturer's instructions.
(b) Assembling and erection work either carried out on Site or off-Site.
20/3
20 FIXTURES AND FITTINGS 20
SPECIAL CONDITIONS
Rates for SC20.09 (c) Installation and fixing work at any positions or heights and irrespective of whether to
proprietary (Cont'd) existing or new surface.
fume cupboards
(Cont'd) (d) All protection of appropriate means prior to and upon completion until the works
are handed over.
(e) Worktop to be constructed in suitable chemical resistant laboratory-grade
materials to be approved by the Maintenance Surveyor.
(f) Either static or mobile units; in the case of mobile units, the units shall be fitted with
lockable castors.
(g) Provision of connections to the necessary plumbing, drainage and building services
installations including electricity connectors, jointing materials and accessories.
Connection to nearest power point shall be carried out by registered electrical workers.
(h) Testing and commissioning on completion.
(i) Submission of catalogues, technical literature and shop drawings for the Maintenance
Surveyor's approval.
(j) Submission of the manufacturer's warranty.
(k) Submission of operation and maintenance manuals.
Rates for SC20.10 The rates for lockers shall include for : -
lockers
(a) Submission of catalogues, technical literature and shop drawings to be approved by
the Maintenance Surveyor.
(b) Submission of samples of components, colour samples, colour charts and other
document demonstrating the properties of moisture and impact resistance, for selection
and consideration by the Maintenance Surveyor.
(c) Provision of prototypes for repetitive fittings, as required, to be approved by the
Maintenance Surveyor prior to fabrication.
(d) All fabrication, assembling and erection work either carried out on Site or off-Site.
(e) Installation and fixing work at any positions and irrespective of whether to existing
or new surface.
(f) All protection of appropriate means prior to and upon completion until the works
are handed over.
(g) Any number of shelving units as required.
(h) Ironmongery and hardware like concealed hinges, cam or latch locks, hanging rods,
hooks and the like and integrated rubber strips.
20/4
20 FIXTURES AND FITTINGS 20
SPECIAL CONDITIONS
Rates for SC20.11 The rates for proprietary recycled plastic seating benches shall include for : -
proprietary
recycled plastic (a) Design, supply, fabrication and installation of the complete system all in accordance
seating benches with the manufacturer's instructions.
(b) Assembling and installation work either carried out on Site or off-Site.
(c) Arm rests at ends of seating benches.
(d) All protection of appropriate means prior to and upon completion until the works
are handed over.
(e) Submission of catalogues, technical literature and shop drawings for the Maintenance
Surveyor's approval.
(f) Submission of the manufacturer's warranty of not less than two (2) years.
Rates for SC20.12 The rates for venetian blinds shall include for : -
venetian blinds
(a) Supplying and fixing of single or multi-coloured slats, rise and fall control mechanism,
locking cord control mechanism, tilt control mechanism, ladder tape, child safety cleat
and all necessary accessories all in accordance with the manufacturer's instructions.
(b) Supplying and fixing of enamel coated galvanized steel or enamel coated, powder
coated or anodized aluminium head and bottom rails.
(c) Plugging and fixing to plastered surfaces or screwing to wooden pelmet.
(d) Making good area disturbed, touching up plasterwork and paintwork where required.
(e) Submission of technical pamphlets and samples of venetian blinds.
(f) Moving and replacing in position all movable furniture as necessary at the time of
execution of works.
Rates for SC20.13 The rates for vertical blinds shall include for : -
vertical blinds
(a) Supplying and fixing of single or multi-coloured blades, base weights, drag and base
connector cords, glider rail, open and close control, and stop control at any position
and all necessary accessories all in accordance with the manufacturer's instructions.
(b) Supplying and fixing of enamel coated galvanized steel or anodized aluminium head rail.
(c) Plugging and fixing to plastered surfaces or screwing to wooden pelmet.
(d) Preparing and applying flame-proof finish to all surfaces of the fabric covering.
(e) Making good area disturbed, touching up plasterwork and paintwork where required.
20/5
20 FIXTURES AND FITTINGS 20
SPECIAL CONDITIONS
Rates for SC20.13 (f) Submission of technical pamphlets and samples of vertical blinds.
vertical blinds (Cont'd)
(Cont'd) (g) Moving and replacing in position all movable furniture as necessary at the time of
execution of works.
Rates for SC20.14 The rates for chic sunblinds shall include for : -
chic sunblinds
(a) Supplying and fixing of single or multi-coloured split bamboo laths, well laced with
best quality waterproof line at 125 mm centres, fixing cord, pulley cleats, screw
hanging eyes and all necessary accessories.
(b) Supplying and fixing 65 mm wide stout fabric bands at both edges.
(c) Supplying and fixing of stout whole bamboo top and bottom.
(d) Plugging and fixing to plastered surfaces or screwing to wooden pelmet.
(e) Spraying fire retardant paint on blinds.
(f) Making good area disturbed, touching up plasterwork and paintwork where required.
(g) Submission of a sample of chic sunblinds.
(h) Moving and replacing in position all movable furniture as necessary at the time of
execution of works.
Rates for SC20.15 The rates for roller blinds shall include for : -
roller blinds
(a) Supplying and fixing of single or multi-coloured curtains with or without linings.
(b) Supplying and installation of switch control, motor and all necessary accessories for
electrically operated roller blinds.
(c) Supplying and installation of rise, fall and stop control mechanism including all
necessary accessories.
(d) Provision of fixing framings or brackets to existing building or structure.
(e) Preparing and applying flame-proof finish to all surfaces of the fabric covering.
(f) Making good areas disturbed, touching up plasterwork and paintwork where
required.
(g) Moving and replacing in position all movable furniture as necessary at the
time of execution of works.
(h) Submission of technical pamphlets and samples of roller blinds.
20/6
20 FIXTURES AND FITTINGS 20
SPECIAL CONDITIONS
Rates for SC20.16 The rates for alteration and repairs items shall generally include for : -
alteration
and repairs (a) Taking down and clearing away of old/defective articles or fittings.
generally
(b) Preparing to receive replacement articles or fittings.
(c) Supplying and fixing new articles or fittings.
(d) All matching screws, spacers, tape, rails and the like.
(e) All labour and material in mortising, fitting, plugging, cutting and pinning.
(f) Making good areas disturbed, touching up plasterwork and paintwork where required.
Rates for SC20.17 The rates for awnings shall include for : -
awnings
(a) Supplying and fixing of single or multi-coloured awnings manually or
electrically operated.
(b) Supplying and installation of switch control, motor and all necessary
accessories as required.
(c) Provision of fixing framings or brackets to existing building or structure.
(d) Preparing and applying flame-proof finish to all surfaces of the fabric covering.
(e) Making good areas disturbed, touching up plasterwork and paintwork where
required.
(f) Submission of technical pamphlets and samples of awnings.
Rates for SC20.18 The rates for blackout curtains and stage curtains shall include for : -
blackout
curtains and (a) Supplying and fixing of single or multi-coloured curtains with or without linings.
stage curtains
(b) All pleats and folding.
(c) Hooks and hangers.
(d) Moving and replacing in position all movable furniture as necessary at the
time of execution of works.
(e) Preparing and applying flame-proof finish to all surfaces of the fabric covering.
(f) Making good areas disturbed, touching up plasterwork and paintwork where
required.
(g) Submission of samples of curtains and linings.
Ironmongery SC20.19 Ironmongery for curtains can be found in Section 09 - Ironmongery of this Schedule.
for curtains
20/7
20 FIXTURES AND FITTINGS 20
SPECIAL CONDITIONS
Rates for SC20.20 The rates for sanitary fittings and parts of sanitary fittings shall generally include for : -
sanitary
fittings and (a) Supply and installation of the sanitary fittings in white or any standard colours,
parts of all in accordance with the manufacturer's recommendations.
sanitary fittings
generally (b) Providing and fixing all necessary accessories, fittings and the like as
recommended by the manufacturer.
(c) Providing all necessary jointing compound, mortar, lead plugs and other ancillary
materials including cutting and pinning or plugging and screwing brackets.
(d) Applying white or coloured silicone sealant after de-greasing and drying of fittings.
(e) Providing and making all necessary connections to water supply services,
overflow, waste and ventilating pipes.
(f) Providing temporary sealing off of water supply services, waste and ventilating
pipes in case when the installation work cannot be completed on time.
(g) Providing and maintaining protective coverings during the progress of work and
subsequently removal of the same, cleaning off when required and upon
completion of works.
Rates for SC20.21 The rates for taps, cocks and mixers shall further include for : -
taps, cocks
and mixers (a) Supply and installation of taps, cocks and mixers in brass, chromium plated brass
and other materials of the like.
(b) Different diameter of fittings, unless otherwise specifically stated.
Rates for fix SC20.22 The rates for fix only of taps, cocks and mixers shall further include for : -
only of taps,
cocks and mixers (a) Provisions of connectors, fittings and jointing materials.
Rates for SC20.23 The rates for sanitary fittings of WSD Water Efficiency Labelling Scheme (WELS)
sanitary fittings grade certification shall further include for : -
of WELS grade
certification (a) Sanitary fittings that have been registered with and certified by WSD under the
WELS as having the specified water efficiency grade.
(b) Submission of the WSD's Certificate of Registration of the sanitary fittings to the
Maintenance Surveyor.
(c) Conformance with the nominal flow rates as specified in the WSD's guidelines of
the relevant water efficiency grades for WELS.
Rates for SC20.24 The rates for toilet fittings and accessories shall include for : -
toilet fittings
and accessories (a) Provisions of all fixing accessories and fittings as recommended by the manufacturer.
20/8
20 FIXTURES AND FITTINGS 20
SPECIAL CONDITIONS
Rates for SC20.24 (b) Providing all necessary jointing compounding, mortar, plugs, screws and the like
toilet fittings (Cont'd) including cutting and pinning.
and accessories
(Cont'd) (c) Applying silicone sealant around toilet fittings and accessories after de-greasing and
drying.
(d) Submission of catalogues, technical literature and shop drawings.
(e) Providing and maintaining suitable protective covering during progress of work
and removal of the same and leaving the toilet fittings and accessories clean upon
completion of works.
Rates for SC20.25 The rates for braille and tactile maps shall include for : -
braille and
tactile maps (a) Design, supply and installation of the braille and tactile maps, all in accordance
with the manufacturer's instructions.
(b) Design, translation and proof reading of Braille message of tactile maps by a
recognized certifying body which shall be a Non-Government (Voluntary)
Organization and is a member of the Hong Kong Joint Council for People with
Disabilities, as accepted by the Maintenance Surveyor.
(c) Finishing all surfaces as required.
(d) All protection of appropriate means prior to and upon completion until the
works are handed over.
(e) Submission of design and shop drawings for the Maintenance Surveyor's
approval.
(f) Making good all disturbed surfaces.
Rates for SC20.26 The rates for projector screens shall include for : -
projector
screens (a) Design, supply and installation of the complete system all in accordance with
the manufacturer's instructions.
(b) Assembling and erection work carried out on Site.
(c) All protection of appropriate means prior to and upon completion until the
works are handed over.
(d) Provision of connection to nearest power point which shall be carried out by
registered electrical workers.
(e) Testing and commissioning on completion.
(f) Submission of catalogues, technical literature and shop drawings.
(g) Submission of the manufacturer's warranty.
(h) Submission of operating and maintenance manuals.
20/9
20 FIXTURES AND FITTINGS 20
SPECIAL CONDITIONS
Rates for SC20.27 The rates for traffic barrier system shall include for : -
traffic barrier
system (a) Design, supply and installation of the complete system all in accordance with
the manufacturer's instructions.
(b) Assembling and erection work carried out on Site.
(c) All protection of appropriate means prior to and upon completion until the
works are handed over.
(d) Provision of connection to nearest power point which shall be carried out by
registered electrical workers.
(e) Testing and commissioning on completion.
(f) Submission of catalogues, technical literature and shop drawings.
(g) Submission of the manufacturer's warranty.
(h) Submission of operating and maintenance manuals.
20/10
20 FIXTURES AND FITTINGS 20
Item Item
JOINERY FITTINGS
Base cabinets, cupboards, hanging cupboards and the like : - Particle
Plywood board or
MDF
A B
Per linear metre $ $
20001 Base cabinet, cupboard, hanging cupboard and the like, n.e. 0.40 m deep and n.e. 0.60 m high............................................................................... 2,194.50 1,905.80 20001
20002 Ditto but 0.60 - 0.90 m high.......................................................................................................................................................................................... 2,830.90 2,673.80 20002
20003 Ditto but 0.90 - 1.10 m high.......................................................................................................................................................................................... 3,505.70 3,280.20 20003
20004 Add to either of Items 20001 to 20003 inclusive for exposed surfaces finished with natural hardwood
veneer............................................................................................................................................................................................................................ 548.60 548.60 20004
Each
20005 Add to either of Items 20001 to 20003 inclusive for glazed door or glazed sliding door n.e. 0.40 m wide
and n.e. 1.10 m high...................................................................................................................................................................................................... 404.30 404.30 20005
Per linear metre
20006 Base cabinet, cupboard, hanging cupboard and the like, 0.40 - 0.60 m deep and n.e. 0.60 m high........................................................................... 2,304.20 1,963.50 20006
20007 Ditto but 0.60 - 0.90 m high.......................................................................................................................................................................................... 2,912.90 2,744.30 20007
20008 Ditto but 0.90 - 1.10 m high.......................................................................................................................................................................................... 3,598.10 3,350.90 20008
20009 Add to either of Items 20006 to 20008 inclusive for exposed surfaces finished with natural hardwood veneer ...................................................... 577.50 577.50 20009
Each
20010 Add to either of Items 20006 to 20008 inclusive for glazed door or glazed sliding door 0.40 - 0.60 m wide
and n.e. 1.10 m high...................................................................................................................................................................................................... 519.80 519.80 20010
20/11
20 FIXTURES AND FITTINGS 20
Item Item
JOINERY FITTINGS (CONT'D)
Tall cabinets, wardrobes and the like : - Particle
Plywood board or
(Note: Cabinets exceeding 1.10 m high are classified as tall cabinets.) MDF
A B
Per linear metre $ $
20011 Tall cabinet, wardrobe and the like, n.e. 0.40 m deep and n.e. 1.80 m high............................................................................................................... 3,840.40 3,234.00 20011
20012 Ditto but 1.80 - 2.40 m high.......................................................................................................................................................................................... 4,937.60 4,158.00 20012
20013 Add to either of Items 20011 to 20012 inclusive for exposed surfaces finished with natural hardwood veneer ...................................................... 932.70 932.70 20013
Each
20014 Add to either of Items 20011 to 20012 inclusive for glazed door or glazed sliding door n.e. 0.40 m wide
and n.e. 2.40 m high...................................................................................................................................................................................................... 646.80 646.80 20014
Per linear metre
20015 Tall cabinet, wardrobe and the like, 0.40 - 0.60 m deep and n.e. 1.80 m high............................................................................................................ 4,042.50 3,436.10 20015
20016 Ditto but 1.80 - 2.40 m high.......................................................................................................................................................................................... 5,197.50 4,417.90 20016
20017 Add to either of Items 20015 to 20016 inclusive for exposed surfaces finished with natural hardwood veneer ...................................................... 979.30 979.30 20017
Each
20018 Add to either of Items 20015 to 20016 inclusive for glazed door or glazed sliding door 0.40 - 0.60 m wide
and n.e. 2.40 m high...................................................................................................................................................................................................... 693.00 693.00 20018
Sink cabinets : - Particle
Plywood board or
(Note : Granite or solid surfacing material or material other than timber to sink top is measured separately.) MDF
A B
Per linear metre $ $
20019 Sink unit n.e. 0.40 m deep and n.e. 0.90 m high.......................................................................................................................................................... 2,830.90 2,323.90 20019
20020 Sink unit 0.40 - 0.60 m deep and n.e. 0.90 m high...................................................................................................................................................... 2,979.90 2,469.10 20020
20021 Add to either of Items 20019 to 20020 inclusive for exposed surfaces finished with natural hardwood veneer....................................................... 519.80 519.80 20021
20/12
20 FIXTURES AND FITTINGS 20
Item Item
JOINERY FITTINGS (CONT'D)
Book shelves, storage shelves, rack units and the like : - Particle
Plywood board or
MDF
A B
Per linear metre $ $
20022 Book shelf, storage shelf, rack unit and the like, n.e. 0.40 m deep and n.e. 0.90 m high........................................................................................... 2,037.40 1,731.80 20022
20023 Ditto but 0.90 - 1.10 m high.......................................................................................................................................................................................... 2,490.20 2,116.70 20023
20024 Ditto but 1.10 - 1.80 m high.......................................................................................................................................................................................... 3,553.40 3,020.40 20024
20025 Ditto but 1.80 - 2.40 m high.......................................................................................................................................................................................... 4,171.90 3,546.10 20025
20026 Add to either of Items 20022 to 20025 inclusive for exposed surfaces finished with natural hardwood veneer....................................................... 603.50 603.50 20026
20027 Book shelf, storage shelf, rack unit and the like, 0.40 - 0.60 m deep and n.e. 0.90 m high........................................................................................ 2,139.30 1,818.40 20027
20028 Ditto but 0.90 - 1.10 m high.......................................................................................................................................................................................... 2,614.70 2,222.50 20028
20029 Ditto but 1.10 - 1.80 m high.......................................................................................................................................................................................... 3,731.00 3,171.40 20029
20030 Ditto but 1.80 - 2.40 m high.......................................................................................................................................................................................... 4,380.50 3,723.40 20030
20031 Add to either of Items 20027 to 20030 inclusive for exposed surfaces finished with natural hardwood veneer....................................................... 633.70 633.70 20031
Reception counters and writing benches with or without under-counter drawers : -
Per linear metre
20032 Reception counter n.e. 0.90 m deep and n.e. 0.90 m high complete with under-counter drawer
0.15 m high, sliding tray and/or key board tray............................................................................................................................................................ 6,006.00 4,937.60 20032
20033 Add to Item 20032 for exposed surfaces finished with natural hardwood veneer ..................................................................................................... 2,887.50 2,367.80 20033
20034 Add to Item 20032 for base cabinet n.e. 0.60 m deep and n.e. 0.90 m high underneath reception counter............................................................... 2,656.50 2,172.60 20034
20035 Add to Item 20032 for drawer cabinet n.e. 0.60 m deep and n.e. 0.90 m high underneath reception counter........................................................... 2,656.50 2,172.60 20035
20036 Add to Item 20032 for shelving rack n.e. 0.30 m deep above reception counter top.................................................................................................. 2,136.80 1,753.30 20036
20037 Add to either of Items 20034 to 20036 inclusive for exposed surfaces finished with natural hardwood veneer ...................................................... 462.00 462.00 20037
20/13
20 FIXTURES AND FITTINGS 20
Item Item
JOINERY FITTINGS (CONT'D)
Reception counters and writing benches with or without under-counter drawers : - (Cont'd) Particle
Plywood board or
MDF
A B
Per linear metre $ $
20038 L-shaped reception counter unit, 700 mm deep and n.e. 0.90 m high overall, comprising of screen partition 1,100 mm
high with quadrant panel at corner and return panel at bottom ends, all covered with fabric on both sides, together
with cantilevered work top and counter top along the girth, both tops having pressure laminated surfaces trimmed
with T moulding and complete with support brackets................................................................................................................................................. 9,124.50 7,432.40 20038
20039 Writing bench n.e. 0.60 m deep fixed to wall complete with metal brackets ............................................................................................................. 3,003.00 2,629.90 20039
20040 Ditto but supported on vertical stand n.e. 0.90 m high................................................................................................................................................ 3,349.50 2,858.60 20040
20041 Add to either of Items 20039 to 20040 inclusive for exposed surfaces finished with natural hardwood veneer ...................................................... 577.50 577.50 20041
20042 Writing bench n.e. 0.90 m deep fixed to wall complete with metal brackets ............................................................................................................. 3,349.50 2,858.60 20042
20043 Ditto but supported on vertical stand n.e. 0.90 m high................................................................................................................................................ 3,684.50 3,144.50 20043
20044 Add to either of Items 20042 to 20043 inclusive for exposed surfaces finished with natural hardwood veneer ...................................................... 577.50 577.50 20044
Pigeon hole racks : -
Per linear metre
20045 Pigeon hole rack n.e. 0.30 m deep and n.e. 0.90 m high.............................................................................................................................................. 2,887.50 2,310.00 20045
20046 Ditto but 0.90 - 1.10 m high.......................................................................................................................................................................................... 3,713.30 2,970.70 20046
20047 Ditto but 1.10 - 1.80 m high.......................................................................................................................................................................................... 5,197.50 4,158.00 20047
20048 Pigeon hole rack 0.30 - 0.60 m deep and n.e. 0.90 m high.......................................................................................................................................... 3,421.70 2,737.40 20048
20049 Ditto but 0.90 - 1.10 m high.......................................................................................................................................................................................... 4,166.70 3,333.30 20049
20050 Ditto but 1.10 - 1.80 m high.......................................................................................................................................................................................... 5,532.50 4,426.00 20050
20/14
20 FIXTURES AND FITTINGS 20
Item Item
JOINERY FITTINGS (CONT'D)
Take Take
down and down and
Fix only
clear set aside
away for re-use
A B C
Per linear metre $ $ $
20051 Base cabinet, cupboard, hanging cupboard and the like, of any sizes....................................................................................................... 202.50 253.10 360.70 20051
20052 Tall cabinet and wardrobe, of any sizes...................................................................................................................................................... 303.70 384.70 541.00 20052
20053 Sink cabinet, book shelves, storage shelves and rack units of any sizes................................................................................................... 202.50 253.10 360.70 20053
20054 Reception counter or writing bench with or without under-counter drawers, of any sizes....................................................................... 303.70 384.70 541.00 20054
20055 Pigeon hole rack of any sizes...................................................................................................................................................................... 202.50 253.10 360.70 20055
PROPRIETARY FUME CUPBOARDS
Proprietary fire resistant double wall type fume cupboard with interior cabin body made of electro-galvanized steel and exterior
body cabin constructed of cold-laminated steel with an organic coating of epoxy polyester resin or other similar finish; complete with
airflow indicator control, safety devices, all control and monitoring system, 250 mm diameter polypropylene ductwork upto 3 m long,
exhaust extraction system including steel support frame, extraction fan and motor and enclosure, worktop and sink, accessories
like oval drip cup, water tap, gas outlet, electricity outlet and the like; all connection and testing and commissioning works on completion,
all in accordance with the manufacturers instructions and conformance to EN 14175 and BS 7258.
(associated power, water and gas supply measured separately)
A
Per set $
20056 Proprietary fume cupboard overall size : 1200 x 2300 x 810 mm................................................................................................................................................. 45,114.30 20056
20057 Ditto; overall size 1500 x 2300 x 810 mm..................................................................................................................................................................................... 48,024.90 20057
Proprietary school type fume cupboard constructed of 4-sides of toughened glass sash, side panels and baffles, with front fascia
constructed of aluminium panel with epoxy powder coated or other similar finish, complete with two-compartment base storage
cupboard for acid and inflammable liquids, cast epoxy resin worktop and sink; airflow indicator control, safety devices, all
control and monitoring system, 250 mm diameter polypropylene ductwork upto 3 m long, exhaust extraction system including
steel support frame, extraction fan and motor and enclosure, accessories like oval drip cup, water tap, gas outlet, electricity outlet
and the like; all connection and testing and commissioning works on completion, all in accordance with the manufacturers
instructions and conformance to EN 14175 and BS 7258. (associated power, water and gas supply measured separately)
Per set
20058 Proprietary fume cupboard overall size : 1200 x 2400 x 800 mm................................................................................................................................................. 42,815.20 20058
20059 Ditto overall size : 1500 x 2400 x 800 mm.................................................................................................................................................................................... 45,384.10 20059
20/15
20 FIXTURES AND FITTINGS 20
Item Item
EXTENSION TO DUCTWORK AND EXHAUST FANS TO FUME CUPBOARDS
A
Per linear metre $
20060 Add to either of Items 20056 to 20059 inclusive for extension of 250 mm diameter polypropylene ductwork connecting to
exhaust system of fume cupboard, mounted either on internal or external wall or roof, complete with steel support frame
and fixing accessories, connectors to exhaust outlet; all necessary builder's works as required; all connection and testing
and commissioning works on completion of the whole exhaust system in conjunction with the proprietary fume cupboard,
and all in accordance with the manufacturer's instructions and conformance to EN 14175 and BS 7258.
(fume cupboard, fan, motor and power supply measured separately)........................................................................................................................................... 1,091.50 20060
Per set
20061 Add to either of Items 20056 to 20059 inclusive for exhaust fan and motor complete with steel support frame, enclosure for fan
and motor, fixing accessories; connecting to extended ductwork; mounted either on external wall or roof; all necessary safety
devices, control and monitoring panel, connectors to the extended ductwork and exhaust system; builder's works as required; all
connection and testing and commissioning on completion of the whole exhaust system in conjunction with the proprietary fume
cupboard, and all in accordance with the manufacturer's instructions and conformance to EN 14175 and BS 7258. (fume cupboard,
ductwork and power supply measured separately)......................................................................................................................................................................... 12,370.10 20061
LABORATORY BENCHES AND FITTINGS
Laboratory benches comprising heavy duty steel framework complete with worktop of compact laminate
or epoxy resin panels with chemical resistant properties, with or without central spine units, shelving units,
hanging cabinets, under bench cabinets, sink units, laboratory valves, nozzles, swivel spout fittings, in high
gauge brass free from impurity coated with chemically resistant polyester powder coating; accessories
Take Take
like oval drip cup, water taps, gas outlets, electricity outlets and the like; all connection and testing and
Supply down and down and
commissioning works on completion, in accordance with the manufacturer's instructions Fix only
and fix clear set aside
(associated power, water and gas supply measured separately) away for re-use
A B C D
Per linear metre $ $ $ $
20062 Laboratory side bench, 0.60 - 0.70 m deep and n.e. 0.90 m high, complete with under bench
cabinets but without spine unit................................................................................................................................................. 2,362.30 191.30 255.10 369.30 20062
20063 Laboratory island bench, 1.20 - 1.50 m deep and n.e. 0.90 m high, complete with under bench
cabinets but without spine unit................................................................................................................................................. 4,374.70 318.90 382.70 587.10 20063
20064 Ditto but with central spine unit, shelving unit and/or hanging cupboards............................................................................. 15,142.70 510.20 637.80 956.30 20064
Each
20065 Add to either of Items 20062 to 20064 inclusive for chemical resistant fireclay sink with laboratory stop tap
with swivel outlet, acid resistant dilution trap and overflow................................................................................................... 1,067.80 67.00 69.50 131.50 20065
20/16
20 FIXTURES AND FITTINGS 20
Item Item
LABORATORY BENCHES AND FITTINGS (CONT'D)
Laboratory fittings in high gauge brass free from impurity coated with chemically resistant polyester
Take Take
powder coating complying with EN 200/DIN 17660 with nitrite seat for leak prove and approved
Supply down and down and
by W.W.O. with international code colour index to DIN EN 13792-2002. Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20066 Water fitting, wall mounted straight valve with removable nozzle ......................................................................................... 403.40 8.30 9.60 88.30 20066
20067 Water fitting with bib cock, wall mounted straight valve with removable nozzle ................................................................. 403.40 8.30 9.60 88.30 20067
20068 Bench mounted swivel swan neck water fitting with removable nozzle ................................................................................ 768.10 10.20 11.50 106.00 20068
20069 Bench mounted swivel swan neck water fitting with bore anti-splash nozzle ...................................................................... 775.40 10.20 11.50 106.00 20069
20070 Bench mounted swivel swan neck water fitting with two way side arm angle valve with removal nozzle .......................... 1,621.70 10.20 11.50 106.00 20070
20071 Bench mounted two way swivel swan neck water fitting with removal nozzle .................................................................... 1,359.70 10.20 11.50 106.00 20071
LOCKERS
Locker with panels made of impact and moisture resistant compact laminate or solid phenolic core panel
Take Take
conforming to EN 438 and metal framework including hinges, cam lock or latch lock and keys, with master
Supply down and down and
keying system, locker numbering labels and rubber strip Fix only
and fix clear set aside
away for re-use
A B C D
Per set $ $ $ $
20072 Locker, one tier, 300 mm wide x 300 - 500 mm deep x 1800 - 2000 mm high...................................................................... 2,266.80 63.80 127.60 190.50 20072
20073 Ditto but two tiers ..................................................................................................................................................................... 2,699.80 63.80 127.60 190.50 20073
20074 Ditto but three tiers.................................................................................................................................................................... 3,018.30 63.80 127.60 190.50 20074
20075 Ditto but four tiers..................................................................................................................................................................... 3,442.00 63.80 127.60 190.50 20075
20076 Ditto but five tiers...................................................................................................................................................................... 3,847.10 63.80 127.60 190.50 20076
20077 Ditto but six tiers....................................................................................................................................................................... 4,341.90 63.80 127.60 190.50 20077
20078 Extra over either of Items 20072 to 20077 inclusive for each locker door
for coin-return locking device................................................................................................................................................... 528.10 - - - 20078
20079 Extra over either of Items 20072 to 20077 inclusive for each locker door
for pad lock device.................................................................................................................................................................... 135.50 - - - 20079
20/17
20 FIXTURES AND FITTINGS 20
Item Item
LOCKERS (CONT'D)
Locker with panels made of mild cold rolled steel with powder coated or baked
Take Take
enamel finish and metal framework including hinges, cam lock or latch lock and keys,
Supply down and down and
with master keying system, locker numbering labels and rubber strip Fix only
and fix clear set aside
away for re-use
A B C D
Per set $ $ $ $
20080 Locker, one tier, 300 mm wide x 300 - 500 mm deep x 1800 - 2000 mm high...................................................................... 1,727.90 63.80 127.60 148.20 20080
20081 Ditto but two tiers ..................................................................................................................................................................... 1,924.20 63.80 127.60 148.20 20081
20082 Ditto but three tiers.................................................................................................................................................................... 2,022.40 63.80 127.60 148.20 20082
20083 Ditto but four tiers..................................................................................................................................................................... 2,120.60 63.80 127.60 148.20 20083
20084 Ditto but five tiers...................................................................................................................................................................... 2,245.30 63.80 127.60 148.20 20084
20085 Ditto but six tiers....................................................................................................................................................................... 2,316.90 63.80 127.60 148.20 20085
20086 Extra over either of Items 20080 to 20085 inclusive for each locker door
for coin-return locking device................................................................................................................................................... 528.10 - - - 20086
20087 Extra over either of Items 20080 to 20085 inclusive for each locker door
for pad lock device.................................................................................................................................................................... 135.50 - - - 20087
Replacement parts only : -
Each
20088 Supply only additional key and plastic key plate...................................................................................................................... 10.10 - - - 20088
20089 Door hinge................................................................................................................................................................................. 55.30 2.60 5.10 11.00 20089
20090 Cam lock ................................................................................................................................................................................... 145.50 3.20 9.60 27.90 20090
20/18
20 FIXTURES AND FITTINGS 20
Item Item
PROPRIETARY RECYCLED PLASTIC SEATING BENCHES
Proprietary recycled plastic seating benches of outdoor quality including back and arm rests with
Take Take
intermediate and end supports with slats in recycled plastic and polyester powder coated finish,
Supply down and down and
UV, moss, algae and impact resistant; rot, splinter and crack proof, and supports in cast iron with Fix only
and fix clear set aside
zinc rich epoxy coated complete with anchorage and fixing accessories, all in accordance with the away for re-use
manufacturer's instructions
A B C D
Each $ $ $ $
20091 Seating bench, 1200 - 1500 mm long x 600 - 750 mm wide................................................................................................... 5,566.50 127.60 191.30 222.30 20091
20092 Ditto, 1500 - 1800 mm long x 600 - 750 mm wide.................................................................................................................. 6,403.30 153.10 229.60 266.80 20092
20093 Ditto, 1800 - 2000 mm long x 600 - 750 mm wide.................................................................................................................. 7,640.30 191.30 293.40 340.90 20093
20094 Ditto, 2000 - 2500 mm long x 600 - 750 mm wide.................................................................................................................. 9,313.90 255.10 382.70 444.70 20094
A
Each $
20095 Add to either of Items 20091 to 20094 inclusive for intermediate arm rest to seating bench...................................................................................................... 218.30 20095
CHANGING SEATING BENCHES
Changing seating benches comprising compact laminated seat made of impact and moisture resistant
Take Take
compact laminate conforming to BS EN 438, including back rest, coat hook rail and coat hooks, stainless
Supply down and down and
steel or powder coated aluminium framing and all necessary accessories, all in accordance with Fix only
and fix clear set aside
the manufacturer's instructions away for re-use
A B C D
Per linear metre $ $ $ $
20096 Changing seating bench, 900 mm deep x 450 mm high.......................................................................................................... 2,897.70 63.80 127.60 151.50 20096
20097 Changing seating bench, single side, 450 mm deep x 450 mm high with 1650 mm high coat hook
rail.............................................................................................................................................................................................. 2,679.00 63.80 127.60 151.50 20097
20098 Changing seating bench, double side, 900 mm deep x 450 mm high with 1650 mm high coat hook
rail.............................................................................................................................................................................................. 4,598.60 127.60 255.10 302.90 20098
20/19
20 FIXTURES AND FITTINGS 20
Item Item
WRITING BOARDS / NOTICE BOARDS / CHALKBOARDS
Proprietary writing or notice boards in any colour with or without magnetic effect
Supply and fix Take Take
including aluminium frame, bottom rail, all necessary accessories and
down and down and
fixing all in accordance with the manufacturer's recommendations : - Fix only
Board size (m2) clear set aside
away for re-use
n.e. 1.0 1.0 - 2.0 exc. 2.0
A B C D E F
Per square metre $ $ $ $ $ $
20099 Proprietary writing or notice board in either ceramic or painted-surface board
with writing surface in silica polyester compound, with or without magnetic
effect including aluminium frame, bottom rail, complete with all necessary
accessories and fixing............................................................................................................................ 643.30 642.00 613.70 16.00 25.60 44.50 20099
20100 Proprietary triple coated writing board with acrylic resin top-coat over a galvanized steel
base sheet, rust proof, surface hardness to 8H, smooth, magnetic, no discoloration; optional
green chalk board with grid pattern; notice board to have 10 mm insulation board core
with plywood backing, Hessian fabric cover and extruded anodized aluminium frame,
including bottom rail, complete with all necessary accessories and fixing......................................... 357.70 338.30 319.10 12.80 22.40 36.90 20100
Proprietary chalkboard stands on floor or fixed to wall all as recommended by the manufacturer : -
Take Take
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Per square metre $ $ $ $
20101 Proprietary chalkboard comprising 4 mm thick high pressure laminated (HPL) based boards
of standard green colour, stain resistant and to NEMA LD3 standard, properties on resistance
to wear, impact, scratch, on flatness dimensional stability and reaction to immersion in boiling
water to meet BS EN458 (framework and backing measured separately)............................................................................... 478.40 10.80 21.10 33.80 20101
20102 Proprietary revolving surface writing board, with fixing plates, chalk writing surface to be magnetic, in
black or green, standard framework for roller boards in top quality timber, aluminium or medium
density fibreboard...................................................................................................................................................................... 1,849.20 72.80 90.40 72.80 20102
20103 Proprietary magnetic green / white board , 1.20 m wide, facing sheet to be vitreous porcelain enamel
with base metal, plywood core, perimeter trim in extruded anodized aluminium channel with rounded
rubber corner, complete with aluminium tube chalk trough installed with concealed bracket fastener................................. 1,041.90 37.40 52.20 60.80 20103
BAIZE OR NOTICE BOARD FELT
A
Per square metre $
20104 Good quality red, green, blue or black baize or fine felt, fixed to doors, notice and directory boards and the like
with adhesive or brass nails as required......................................................................................................................................................................................... 256.80 20104
20105 Ditto but fixed to grooved plastic name plates and notice boards (measured separately) including working
into grooves (measured flat overall grooves).................................................................................................................................................................................. 261.90 20105
20106 Ditto but fixed to grooved plywood or timber name and directory boards (measured separately) including cutting grooves in plywood
or timber and working the baize or felt into the same (measured flat overall grooves)................................................................................................................ 267.30 20106
20/20
20 FIXTURES AND FITTINGS 20
Item Item
CLOTHES DRYING RACKS
Side-way type pulley operated clothes drying rack, with aluminium self-retractable roller Take Take
system and nylon pulley system, wall mounted with stainless steel supporting brackets and Supply down down Fix
complete with gear box accessories and and and set only
fix clear aside for
away re-use
A B C D
Each $ $ $ $
20107 Clothes drying rack, 1500 mm long x 600 - 750 mm wide...................................................................................................... 705.80 31.90 38.30 42.20 20107
VENETIAN BLINDS
Area of blinds (m)
n.e. 1.0 1.0 - 1.5 1.5 - 2.0 Exc. 2.0
A B C D
Per square metre $ $ $ $
20108 Blinds in individual size............................................................................................................................................................ 212.80 177.40 153.90 139.20 20108
A
Per square metre $
20109 Extra over for forming graphics and the like on one side.............................................................................................................................................................. 50.20 20109
20110 Ditto but on both sides.................................................................................................................................................................................................................... 87.90 20110
Each
20111 Extra over for forming opening of any size.................................................................................................................................................................................... 40.20 20111
Alteration and repairs : -
Take down and clear away the following old or defective articles or fittings, and supply and fix new articles or fittings : -
Per linear metre
20112 Slat................................................................................................................................................................................................................................................... 15.00 20112
20113 Head rail.......................................................................................................................................................................................................................................... 70.40 20113
20114 Bottom rail....................................................................................................................................................................................................................................... 62.40 20114
20115 Lift cord........................................................................................................................................................................................................................................... 10.60 20115
20116 Ladder cord...................................................................................................................................................................................................................................... 15.00 20116
20117 U rod................................................................................................................................................................................................................................................ 20.20 20117
20/21
20 FIXTURES AND FITTINGS 20
Item Item
VENETIAN BLINDS (CONT'D)
Alteration and repairs : - (Cont'd)
Take down and clear away the following old or defective articles or fittings, and supply and fix new articles or fittings : - (Cont'd)
A
Each $
20118 Tassel............................................................................................................................................................................................................................................... 6.70 20118
20119 Tilter................................................................................................................................................................................................................................................ 29.90 20119
20120 Cord lock......................................................................................................................................................................................................................................... 35.20 20120
20121 Fixing bracket.................................................................................................................................................................................................................................. 24.60 20121
20122 Tape roll and tape holder................................................................................................................................................................................................................ 24.60 20122
20123 750 mm Long solid core wand with hook...................................................................................................................................................................................... 35.50 20123
20124 1,000 mm Long ditto....................................................................................................................................................................................................................... 55.70 20124
20125 1,300 mm Long ditto....................................................................................................................................................................................................................... 66.70 20125
20126 1,500 mm Long ditto....................................................................................................................................................................................................................... 76.20 20126
20127 2,300 mm Long ditto....................................................................................................................................................................................................................... 137.30 20127
20128 End cap to head or bottom rails...................................................................................................................................................................................................... 6.90 20128
20129 Slat clip............................................................................................................................................................................................................................................ 5.60 20129
Sundries Area of blinds (m)
N.e. 3.0 Exc. 3.0
A B
Each $ $
20130 Take down venetian blinds and fittings, reduce to smaller size (any area), ease, adjust and re-fix in original or
other position, including replacement of parts (take down area measured)................................................................................................................ 140.80 158.40 20130
20131 Take down existing venetian blinds and set aside for re-fix........................................................................................................................................ 25.40 28.90 20131
20132 Ditto but clear away from Site...................................................................................................................................................................................... 28.90 34.30 20132
20133 Fix only venetian blinds................................................................................................................................................................................................ 65.80 76.30 20133
20/22
20 FIXTURES AND FITTINGS 20
Item Item
VERTICAL BLINDS
Area of blinds (m)
N.e. 1.0 1.0 - 1.5 Exc. 1.5
A B C
Per square metre $ $ $
20134 Blinds in individual size.............................................................................................................................................................................. 195.40 167.50 147.50 20134
A
Each $
20135 Extra over for forming opening of any size.................................................................................................................................................................................... 56.40 20135
Alteration and repairs : -
Take down and clear away the following old or defective articles or fittings, and supply and fix new articles or fittings : -
A
Per linear metre $
20136 Fabric louvre.................................................................................................................................................................................................................................... 10.20 20136
20137 Drawing cord................................................................................................................................................................................................................................... 35.10 20137
20138 Bead chain....................................................................................................................................................................................................................................... 19.30 20138
Each
20139 Base weight..................................................................................................................................................................................................................................... 17.60 20139
20140 End cap............................................................................................................................................................................................................................................ 7.60 20140
20141 Hanger............................................................................................................................................................................................................................................. 12.30 20141
20142 Set of Runner................................................................................................................................................................................................................................... 85.20 20142
20143 Spacer.............................................................................................................................................................................................................................................. 9.30 20143
Area of blinds (m)
N.e. 3.0 Exc. 3.0
A B
Each $ $
20144 Take down vertical blinds and fittings, reduce to smaller size (any area), ease, adjust and re-fix in original or
other position, including replacement of parts (take down area measured)................................................................................................................ 119.30 136.90 20144
20145 Take down existing vertical blinds and set aside for re-fix.......................................................................................................................................... 14.00 16.70 20145
20146 Ditto but clear away from Site...................................................................................................................................................................................... 21.10 24.90 20146
20147 Fix only vertical blinds.................................................................................................................................................................................................. 65.80 78.00 20147
20/23
20 FIXTURES AND FITTINGS 20
Item Item
CHIC SUNBLINDS
Area of blinds (m)
N.e. 1.0 1.0 - 1.5 1.5 - 2.0 Exc. 2.0
A B C D
Per square metre $ $ $ $
20148 Chic sunblinds in individual size.............................................................................................................................................. 298.80 293.10 287.60 167.30 20148
A
Each $
20149 Extra over for forming opening of any size.................................................................................................................................................................................... 47.80 20149
Alterations and repairs : - Area of blinds (m)
N.e. 3.0 Exc. 3.0
A B
Each $ $
20150 Take down chic sunblinds and fittings, reduce to smaller size (any area), ease, adjust and re-fix in original or
other position, including replacement of parts (take down area measured)................................................................................................................ 129.90 147.40 20150
20151 Take down, set aside for re-use chic sunblinds and associated cord and fittings........................................................................................................ 21.60 25.00 20151
20152 Ditto but clear away from Site...................................................................................................................................................................................... 23.90 32.80 20152
20153 Fix only chic sunblinds complete with cord and fittings.............................................................................................................................................. 57.30 64.50 20153
ROLLER BLINDS Height (m)
N.e 1.0 1.0-2.0 Exc. 2.0
A B C
Per square metre $ $ $
20154 Blinds in individual size, manually operated.............................................................................................................................................. 190.60 157.60 150.70 20154
20155 Blinds in individual size, electrically operated........................................................................................................................................... 580.80 554.40 482.10 20155
20156 Extra over either of Items 20154 to 20155 inclusive for additional blackout blinds................................................................................ 102.90 102.90 102.90 20156
A
Each $
20157 Extra over for forming opening of any size.................................................................................................................................................................................... 100.60 20157
20/24
20 FIXTURES AND FITTINGS 20
Item Item
ROLLER BLINDS (CONT'D)
Alterations and repairs :-
A
Each $
20158 Take down roller blinds and fittings, reduce to smaller size (any area), ease, adjust and re-fix in original or
other position, including replacement of parts (take down area measured).................................................................................................................................. 141.30 20158
20159 Take down existing roller blinds and set aside for re-fix............................................................................................................................................................... 10.50 20159
20160 Ditto but clear away from Site........................................................................................................................................................................................................ 15.60 20160
20161 Fix only roller blinds....................................................................................................................................................................................................................... 85.10 20161
AWNINGS
Projection of
awning on plan
(m)
Awnings complete with all necessary accessories. N.e. 14.50 -
14.50 29.00
A B
Per square metre $ $
20162 Awnings in individual size, manually operated........................................................................................................................................................... 555.80 500.20 20162
20163 Ditto, electrically operated ........................................................................................................................................................................................... 687.10 582.80 20163
20164 Awning fabric to existing awning frame...................................................................................................................................................................... 300.60 270.30 20164
Sundries
A
Per square metre $
20165 Take down existing manually operated awnings and set aside for re-fix...................................................................................................................................... 15.60 20165
20166 Ditto but clear away from Site........................................................................................................................................................................................................ 19.50 20166
20167 Take down existing electrically operated awnings and set aside for re-fix................................................................................................................................... 23.40 20167
20168 Ditto but clear away from Site........................................................................................................................................................................................................ 26.30 20168
20169 Fix only manually operated awnings, including plugging, cutting and pinning etc., and making good and leaving in good order............................................ 156.90 20169
20170 Ditto, but electrically operated........................................................................................................................................................................................................ 167.60 20170
20/25
20 FIXTURES AND FITTINGS 20
Item Item
CANVAS
Take Take
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Per square metre $ $ $ $
20171 Best stripped drill canvas made up, including all seaming, scalloped edges and similar labours,
providing and fixing any tying tape or cord, and fixing complete in sunshades and similar
positions (rollers and framework measured separately)........................................................................................................... 65.60 6.80 7.80 10.70 20171
BLACKOUT CURTAINS Blackout curtains
with without
linings linings
A B
Per square metre $ $
20172 Blackout curtains of twill, polyester or velvet, fixed to curtain rails and tracks (measured separately)..................................................................... 271.80 185.50 20172
A
Each $
20173 Extra over for forming opening of any size.................................................................................................................................................................................... 95.90 20173
Sundries
A
Per square metre $
20174 Take down and clear away blackout curtains and associated cord and fittings............................................................................................................................. 6.80 20174
20175 Take down, set aside for re-use blackout curtains and associated cord and fittings..................................................................................................................... 7.80 20175
20176 Fix only blackout curtains completed with cord and fittings......................................................................................................................................................... 16.60 20176
20/26
20 FIXTURES AND FITTINGS 20
Item Item
STAGE CURTAINS
Stage curtains
with without
linings linings
A B
Per square metre $ $
20177 Cotton velveteen stage curtain with valance fixed on curtain rails and tracks (measured separately)....................................................................... 162.70 137.70 20177
Sundries Stage curtains
with without
linings linings
A B
Per square metre $ $
20178 Take down and clear away stage curtains and associated cord and fittings................................................................................................................ 9.10 7.80 20178
20179 Take down, set aside for re-use stage curtains and associated cord and fittings......................................................................................................... 8.90 7.80 20179
20180 Fix only stage curtains complete with cord and fittings............................................................................................................................................... 20.50 18.50 20180
SANITARY FITTINGS
LAVATORY BASINS
Vitreous china wash basins complete with waste fittings, plug and chain, trap fittings, tap hole
Take Take
with overflow and fixing brackets and accessories.
Supply down and down and
Fix only
and fix clear set aside
Note: All taps, cocks and mixers are measured separately. away for re-use
A B C D
Each $ $ $ $
20181 Counter top wash basin ............................................................................................................................................................ 547.50 74.60 76.50 176.60 20181
20182 Under-counter wash basin ........................................................................................................................................................ 662.50 67.00 69.50 176.60 20182
20183 Wall hung wash basin ............................................................................................................................................................. 458.90 74.60 76.50 176.60 20183
20/27
20 FIXTURES AND FITTINGS 20
Item Item
SANITARY FITTINGS (CONT'D)
WATER CLOSETS
Vitreous china water closet suites complete with seat and cover, cistern with flushing devices,
Take Take
traps, flush bend and pipes, syphon fittings, ball valves, inlet and outlet connectors and fixing
Supply down and down and
accessories. Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20184 Close-coupled W.C. suite complete with low or high level cistern with lever flush or
push button, 6 litre single flush or 6 / 4 litre dual flush and "P" or "S"-trap............................................................................ 988.40 76.50 79.10 247.20 20184
20185 Wash down wall-hung W.C. pan complete with bottom or top inlet concealed cistern
with push button, 6 litre single flush or 6 / 4 litre dual flush and "P" or "S"-trap................................................................... 1,773.90 76.50 79.10 247.20 20185
20186 Accessible W.C. suite complete with low or high level cistern with lever flush,
6 litre single flush or 6 / 4 litre dual flush and "P" or "S"-traps............................................................................................... 1,794.70 77.80 83.60 266.70 20186
Squatting type water closet pans complete with cistern and flushing device, traps, flush bend and
pipes, syphon fittings, ball valves, angle valves, inlet and outlet connector and fixing accessories
including bedding pan in cement mortar (concrete surround measured separately).
Each
20187 Vitreous china squatting W.C. pan complete with high or medium level cistern with lever flush, 6 litre
single flush device or 6 / 4 litre dual flush and "P" or "S"-trap................................................................................................ 1,205.40 77.80 83.60 269.30 20187
20188 Approved stainless steel Grade 316 floor mounted pedestal W.C. pan complete with low, medium
or high level cistern and fittings, single or dual flushing device and "P" or "S"-trap ............................................................. 7,233.50 127.60 191.30 441.50 20188
20189 Approved stainless steel Grade 316 floor mounted squatting W.C. pan complete with high or medium
level cistern and fittings, single or dual flushing device and "P" or "S"-trap.......................................................................... 2,079.50 68.90 72.70 247.20 20189
20190 Approved stainless steel Grade 316 floor mounted squatting W.C. pan complete with low level cistern
and fittings, single or dual flushing device, foot control and "P" or "S"-trap.......................................................................... 2,185.40 95.70 111.60 353.20 20190
20191 Fireclay plate floor mounted squatting W.C. wash-down pan complete with integral foot treads, low
level cistern and fittings, flushing device and "S"-trap............................................................................................................ 756.90 31.90 32.50 116.60 20191
20/28
20 FIXTURES AND FITTINGS 20
Item Item
SANITARY FITTINGS (CONT'D)
URINALS
Take Take
Supply down and down and
Urinals complete with grating, traps, flush bend and pipes, fittings, valves, inlet and outlet connectors Fix only
and fix clear set aside
and fixing accessories. away for re-use
A B C D
Each $ $ $ $
20192 Single individual stall pattern vitreous china urinal complete with grating and trap
(cistern, spreader, etc., measured separately) .......................................................................................................................... 1,332.20 60.60 63.80 203.10 20192
20193 Add to Item 20192 for each additional individual stall in the same range including overlap facings
if required.................................................................................................................................................................................. 1,399.70 60.60 63.80 203.10 20193
20194 Single section slab pattern urinal n.e. 1.00 m wide complete with two return ends, floor channel,
outlet grating and trap including bedding in cement mortar and pointing in white cement
(cistern, spreader, etc., measured separately) .......................................................................................................................... 4,397.50 111.60 121.20 375.30 20194
20195 Add to Item 20194 for each additional 610 mm wide back section and length of floor channel in the
same range ................................................................................................................................................................................ 1,720.00 61.20 64.40 264.90 20195
20196 Ditto for each intermediate division slab ................................................................................................................................. 1,405.80 31.90 32.50 132.50 20196
20197 Stall urinal in stainless steel Grade 316, size 975 mm high x 600 mm wide and n.e. 750 mm long,
complete with stainless steel Grade 316 hinged foot grating, level floor or tile step, outlet grating
(cistern, spreader, etc. measured separately) ........................................................................................................................... 6,822.60 111.60 133.90 273.70 20197
20198 Add to Item 20197 for each additional 300 mm long in the same range ................................................................................ 2,954.80 28.70 35.70 44.20 20198
Per linear metre
20199 Add to stall urinal for stainless steel step ................................................................................................................................ 1,880.90 18.50 19.80 61.80 20199
Each
20200 Wall urinal bowl complete with outlet grating, trap and concealed brackets or hanger (cistern, spreader, etc.,
measured separately) ................................................................................................................................................................ 875.90 30.60 38.30 79.50 20200
20201 Division slab between wall urinal bowls complete with concealed hanger ........................................................................... 444.40 11.50 14.00 44.20 20201
20202 Automatic flushing cistern (any size) complete with brackets or hanger, pet cock, and flush pipe and spreader
for single urinal stall or bowl, or flush and sparge pipe n.e. 1 m long for single section slab urinal ..................................... 457.50 63.80 70.20 132.40 20202
20203 Add to Item 20202 for each additional stall or bowl or 610 mm width of stall urinal served from the same
cistern ........................................................................................................................................................................................ 374.70 10.20 11.50 42.40 20203
20/29
20 FIXTURES AND FITTINGS 20
Item Item
SANITARY FITTINGS (CONT'D)
Take Take
SINKS
Supply down and down and
Fix only
and fix clear set aside
(Note: All sink mixers or faucets are measured separately.) away for re-use
A B C D
Each $ $ $ $
20204 Stainless steel Grade 316 single bowl sink complete with waste fitting, plug and chain, trap fitting, tap
hole with overflow and fixing brackets and accessories.......................................................................................................... 1,435.50 67.00 69.50 247.20 20204
20205 Add to Item 20204 for drain board n.e. 1.00 m long................................................................................................................ 886.60 43.40 45.30 158.90 20205
20206 Add to Item 20204 for drain board 1.00 - 1.60 m long............................................................................................................ 1,413.60 44.70 45.90 176.60 20206
20207 Stainless steel Grade 316 double bowl sink complete with waste fitting, plug and chain, trap, tap hole
with overflow and fixing brackets and accessories.................................................................................................................. 1,151.70 67.00 69.50 264.90 20207
20208 Add to Item 20207 for drain board n.e. 1.00 m long................................................................................................................ 1,359.60 43.40 45.30 158.90 20208
20209 Add to Item 20207 for drain board 1.00 - 1.60 m long............................................................................................................ 1,886.60 44.70 45.90 176.60 20209
Each
20210 Hospital sluice fitting comprising combined bed-pan and wash up sink complete with loose or fixed trap,
brackets, urinal bottle and bed-pan jets, high level cistern with brackets and flush pipe, waste fitting, plug
and chain, drainer, supply fitting and hand spray with supply fitting ..................................................................................... 16,376.30 260.20 264.00 830.00 20210
20211 Slop sink (any size) complete with drainer, overflow, waste fitting, plug and chain, trap and brackets................................ 11,904.50 77.20 79.10 309.10 20211
(Note : Items 20210 and 20211 inclusive will only be paid for if ordered by the Maintenance Surveyor in writing)
SHOWER TRAYS AND BATH TUBS
Note: All shower and bath fittings, mixers or faucets are measured separately.
Each
20212 Shower tray (any size) complete with waste fitting, plug and chain, and trap including bedding in cement
mortar and pointing in white or coloured cement (concrete surround or benching measured separately) ............................ 1,711.80 115.40 116.10 362.00 20212
20213 Vitreous enamelled cast iron bath n.e. 2 m long complete with combined overflow and waste fitting, plug
and chain and trap..................................................................................................................................................................... 2,643.10 151.80 154.30 485.70 20213
20/30
20 FIXTURES AND FITTINGS 20
Item Item
TAPS, COCKS AND MIXERS
Take Take
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20214 Bib cock, bib tap and stop cock................................................................................................................................................ 230.70 12.80 16.00 70.60 20214
20215 Pillar cock and pillar tap with lever action............................................................................................................................... 259.80 12.80 16.00 70.60 20215
20216 Basin mixer ............................................................................................................................................................................... 623.40 12.80 16.00 68.90 20216
20217 Sink mixer with swivel nozzle.................................................................................................................................................. 374.30 12.80 16.00 81.20 20217
20218 Shower mixer fitting with pillar taps or cocks, shower head and spray handset with flexible hose
including wall brackets and wall mounted tower pole............................................................................................................. 563.60 12.80 16.00 239.30 20218
20219 Bath mixer fitting with fixed nozzle......................................................................................................................................... 312.40 12.80 16.00 133.30 20219
20220 Ditto but for bath with fixed nozzle, diverter automatic fitting, shower head and spray handset with
flexible hose including wall brackets and wall mounted tower pole....................................................................................... 520.70 12.80 16.00 221.60 20220
20221 Add to either of Items 20214 to 20220 inclusive if fitted with "Compression type" connector for copper
tubing (per one end) ................................................................................................................................................................. 37.90 - - 8.80 20221
20222 Ditto if fitted with "Capillary type" connector for copper tubing (per one end) ..................................................................... 54.00 - - 17.70 20222
20/31
20 FIXTURES AND FITTINGS 20
Item Item
SELF-CLOSING TAPS, COCKS AND MIXERS WITH TIME-DELAY CLOSING ACTION
Vandal proof self closing taps or stop cocks with time delay closing action devices complete with fittings
and fixing accessories : - Supply Take down and
and fix clear away
Diameter (mm) 15 20 15 20
A B C D
Each $ $ $ $
20223 Surface mounted self closing non-concussive shower stop cock with built-in adjustable flow rate
device, supplied with anti-theft device fixed overhead shower and riser pipe and hose ........................................................ 1,259.10 1,477.40 31.90 35.10 20223
20224 Concealed self closing non-concussive shower stopcock ditto ............................................................................................... 1,622.90 1,768.40 31.90 35.10 20224
20225 Surface mounted self closing non-concussive shower mixer stop cock , knob to select showering
temperature, built in adjustable flow device supplied with anti-theft device fixed overhead shower
and riser pipe and hose ............................................................................................................................................................. 2,059.50 2,277.80 31.90 35.10 20225
20226 Concealed self closing non-concussive shower mixer stopcock ditto .................................................................................... 2,496.10 2,714.40 31.90 35.10 20226
20227 Self closing non-concussive shower mixer stop cock of WSD's Water Efficiency Labelling Scheme
(WELS) Grade 1 type knob to select showering temperature, built in adjustable flow device
supplied with anti-theft device fixed overhead shower and riser pipe and hose..................................................................... 1,887.80 2,509.70 31.90 35.10 20227
20228 Ditto but Grade 2, 3 or 4 type.................................................................................................................................................... 3,912.30 5,209.00 31.90 35.10 20228
20229 Self closing non-concussive basin pillar tap with time delay closing action, built in adjustable flow
rate device, self cleaning piston and anti-splash gauze strainer .............................................................................................. 677.00 1,040.80 31.90 35.10 20229
20230 Self closing non-concussive basin pillar tap or mixer of WSD's Water Efficiency Labelling Scheme
(WELS) Grade 1 type with built in adjustable flow rate device, self cleaning piston and anti-splash
gauze strainer ............................................................................................................................................................................ 364.10 478.10 31.90 35.10 20230
20231 Ditto but Grade 2, 3 or 4 type.................................................................................................................................................... 735.20 972.90 31.90 35.10 20231
20232 Self closing non-concussive basin pillar tap or mixer with lever action for disabled, with built in
adjustable flow rate device, self cleaning piston and anti-splash gauze strainer .................................................................... 786.10 1,113.60 31.90 35.10 20232
20233 Concealed non-concussive shower stop cock, with lever action for disabled, with lever handle at
least 75mm long from the centre of rotation to the handle tip................................................................................................. 1,002.70 1,102.90 31.90 35.10 20233
20234 Ditto but for shower and bath mixer stop cock ........................................................................................................................ 1,093.80 1,203.20 31.90 35.10 20234
20/32
20 FIXTURES AND FITTINGS 20
Item Item
ELECTRONIC OPERATED TAPS, COCKS AND MIXERS
Electronic operated taps, cocks or mixers with adjustable self closing timing devices, electronic sensor
devices, infra-red sensors, powered by transformer or battery operated complete with control box,
angle stop cocks with built-in filter and check valve, fittings and fixing accessories : - Supply Take down and
and fix clear away
Diameter (mm) 15 20 15 20
A B C D
Each $ $ $ $
20235 Electronic operated basin bib or pillar tap powered by transformer including provision of connection
to nearest power point by a registered electrical worker.......................................................................................................... 2,059.50 2,277.80 31.90 35.10 20235
20236 Ditto but operated by battery .................................................................................................................................................... 1,477.40 1,841.20 31.90 35.10 20236
20237 Electronic operated basin bib or pillar thermostatic mixer powered by transformer including provision
of connection to nearest power point by a registered electrical worker .................................................................................. 2,954.80 3,318.60 31.90 35.10 20237
20238 Ditto but operated by lithium battery ....................................................................................................................................... 2,809.20 3,027.50 31.90 35.10 20238
20239 Wall mounted electronic operated sensor tap with self closing device or premixed with adjustable
sensing distance with special 220 mm projected spout supplied with extra flexible hose and electric
cable with adaptor for 1 m length, powered by transformer including provision of connection to
nearest power point by a registered electrical worker.............................................................................................................. 2,026.50 3,717.70 47.80 54.20 20239
20240 Ditto but operated by battery..................................................................................................................................................... 1,671.50 2,853.40 47.80 54.20 20240
20241 Wall mounted electronic operated thermostatic mixer powered by transformer, including provision
of connection to nearest power point by a registered electrical worker................................................................................... 3,523.80 4,194.20 51.00 63.80 20241
20242 Ditto but operated by battery..................................................................................................................................................... 2,884.40 4,209.80 51.00 63.80 20242
THERMOSTATIC AND THERMOSCOPIC MIXING VALVES Take Take
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20243 Thermostatic mixing valve 15mm ........................................................................................................................................... 931.50 22.30 33.80 58.30 20243
20244 Ditto 20 mm .............................................................................................................................................................................. 1,143.40 22.30 33.80 58.30 20244
20245 Ditto 22 mm .............................................................................................................................................................................. 1,295.30 22.30 33.80 58.30 20245
20246 Ditto 25 mm ............................................................................................................................................................................. 1,440.80 22.30 33.80 58.30 20246
20247 Thermostatic mixing valve 15 mm with safety shut-off device ............................................................................................. 1,004.20 22.30 39.60 58.30 20247
20248 Ditto 20 mm .............................................................................................................................................................................. 1,295.30 22.30 39.60 58.30 20248
20249 Ditto 22 mm .............................................................................................................................................................................. 1,368.10 22.30 39.60 58.30 20249
.
20250 Ditto 25 mm ............................................................................................................................................................................. 1,586.30 22.30 39.60 58.30 20250
20251 15 mm Thermoscopic mixing valve.......................................................................................................................................... 1,440.80 24.20 33.80 58.30 20251
20252 Ditto with safety shut-off device............................................................................................................................................... 1,586.30 24.20 33.80 58.30 20252
20/33
20 FIXTURES AND FITTINGS 20
Item Item
PARTS OF SANITARY FITTINGS
WATER CLOSET ACCESSORIES Take Take
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20253 Solid plastic W.C. seat with moulded plastic adjustable hinges ............................................................................................. 102.00 12.10 14.70 22.10 20253
20254 Ditto but with cover .................................................................................................................................................................. 230.20 14.00 17.20 26.50 20254
20255 Solid W.C. seat with moulded adjustable hinges for disabled................................................................................................. 109.00 12.10 14.70 22.10 20255
20256 India rubber buffer to W.C. seat ............................................................................................................................................... 28.00 1.90 1.90 6.20 20256
20257 Pair of pillar hinges to W.C. seat ............................................................................................................................................. 28.90 1.90 1.90 7.10 20257
20258 Pair of double pillar hinges to W.C. seat and cover ................................................................................................................ 62.60 2.60 2.60 9.70 20258
20259 Vitreous china close-coupled cistern, 6 litre single flush or 6 / 4 litre dual flush, complete with
plastic syphon fittings, ball valve, close coupling fitments, overflow, chromium plated lever or
push button and fittings............................................................................................................................................................. 610.30 40.20 42.10 123.60 20259
20260 Vitreous china low level cistern, 6 litre single flush, complete with plastic syphon fittings, ball valve,
flush bend and pipe, inlet connector, overflow, chromium plated lever and fittings............................................................. 695.90 40.20 42.10 123.60 20260
20261 Vitreous china high level cistern, 6 litre single flush, complete with plastic syphon fittings, ball valve, flush bend and
pipe, inlet connector, overflow, chromium plated chain and rubber pull and fittings............................................................. 657.90 46.60 48.50 150.10 20261
20262 Plastic concealed type cistern, 6 litre single flush or 6 / 4 litre dual flush, complete with plastic syphon fittings,
ball valve, flush bend and pipe, inlet connector, overflow and chromium plated lever or push button................................. 497.60 46.60 48.50 150.10 20262
20263 Plastic low level cistern, 6 litre single flush, complete with plastic syphon fittings, ball valve, flush bend and
pipe, inlet connector, overflow, chromium plated lever and fittings....................................................................................... 450.30 46.60 48.50 150.10 20263
20264 Plastic high level cistern, 6 litre single flush, complete with plastic syphon fittings, ball valve, flush bend and
pipe, inlet connector, overflow, chromium plated chain and rubber pull and fittings............................................................. 321.20 46.60 48.50 150.10 20264
20/34
20 FIXTURES AND FITTINGS 20
Item Item
PARTS OF SANITARY FITTINGS (CONT'D)
WATER CLOSET ACCESSORIES (CONT'D)
Take Take
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20265 Electronic operated vandal proof vitreous china W.C. flush valve approved by Hong Kong Water
Authority suitable for sea water, concealed/built-in type, including infra-red sensor with manual
overriding button in case of failure of sensor, filter before flushing valve and DC powered and
and provision of connection to nearest power point by a registered electrical worker............................................................ 3,125.70 24.90 36.40 106.00 20265
20266 32 mm Self-closing non-concussive flushing devices, inlet connector and remote control system ....................................... 2,216.10 24.90 36.40 106.00 20266
20267 32 mm Diameter stainless steel flushing valve ....................................................................................................................... 1,200.40 22.30 28.70 44.20 20267
20268 Plastic syphon complete with chromium plated outlet connector including adjusting and re-fixing
lever arm ................................................................................................................................................................................... 145.20 26.80 28.10 72.40 20268
20269 Pair of porcelain enamelled brackets........................................................................................................................................ 253.80 9.60 11.50 53.00 20269
20270 Chromium plated brass lever handle with linkage to syphon including adjusting ................................................................. 77.20 16.60 17.90 35.30 20270
20271 Plastic lever handle ditto .......................................................................................................................................................... 54.10 16.60 17.90 35.30 20271
20272 Heavy galvanized chain pull to W.C. cistern ........................................................................................................................... 39.60 16.60 - 14.10 20272
20273 Nylon cord pull ditto ................................................................................................................................................................ 23.10 16.60 - 14.10 20273
20274 Rod pull and guide for high level cistern ................................................................................................................................. 28.50 16.60 - 14.10 20274
20275 Foot operated flushing mechanism .......................................................................................................................................... 672.20 26.20 26.80 90.10 20275
20276 Foot operated duct lever with high level cistern adaptor for wall thickness within 115 mm to 229 mm .............................. 1,107.00 30.00 30.60 88.30 20276
20277 Plastic flush pipe for low level cistern including connector ................................................................................................... 59.40 16.00 17.90 38.00 20277
20278 Plastic adjustable flush pipe for high level cistern .................................................................................................................. 79.40 22.30 23.60 44.20 20278
20279 Plastic flush pipe connector ..................................................................................................................................................... 22.30 7.70 8.30 16.80 20279
20/35
20 FIXTURES AND FITTINGS 20
Item Item
PARTS OF SANITARY FITTINGS (CONT'D)
URINAL FITTINGS AND ACCESSORIES
Take Take
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20280 Electronic operated vandal proof urinal flush valve approved by Hong Kong Water Authority suitable for
sea water, concealed/built-in type, including infra-red sensor with manual overriding button in case of
failure of sensor, filter before flushing valve and powered by transformer and provision of connection
to nearest power point by a registered electrical worker.......................................................................................................... 1,335.70 24.90 36.40 106.00 20280
20281 Urinal flush valve of WSD Water Efficiency Labelling Scheme (WELS) Grade 1 type......................................................... 2,540.00 24.90 36.40 106.00 20281
20282 Ditto but Grade 2, 3 or 4 type.................................................................................................................................................... 2,540.00 24.90 36.40 106.00 20282
20283 Glazed fire-clay automatic flushing cistern, 4.50 litre capacity .............................................................................................. 538.70 24.20 24.90 82.10 20283
20284 Ditto but 9.00 litre capacity ...................................................................................................................................................... 561.90 28.10 28.70 91.80 20284
20285 Ditto but 13.50 litre capacity .................................................................................................................................................... 621.30 31.90 32.50 100.70 20285
20286 Plastic syphon with screwed outlet and rubber washer to suit 4.50 litre capacity automatic flushing
cistern ........................................................................................................................................................................................ 196.70 15.30 16.00 51.20 20286
20287 Ditto but for 9.00 litre capacity automatic flushing cistern ..................................................................................................... 274.80 16.60 17.90 56.50 20287
20288 Ditto but for 13.50 litre capacity automatic flushing cistern ................................................................................................... 352.00 19.80 20.40 60.90 20288
20289 10 mm Plastic drip cock for automatic cistern ........................................................................................................................ 75.60 7.70 8.30 28.30 20289
20290 10 mm Brass drip cock ditto .................................................................................................................................................... 252.70 9.60 10.20 34.40 20290
20291 P.V.C. flush pipe and spreader for single urinal stall or bowl ................................................................................................ 227.40 20.40 21.10 60.10 20291
20292 Add to Item 20291 for each additional stall or bowl in a range served from the same cistern .............................................. 198.30 9.60 10.20 30.90 20292
20293 P.V.C. flush pipe and sparse pipe n.e. 1 m long for single section slab urinal ....................................................................... 383.50 26.80 27.40 70.60 20293
20294 Add to Item 20293 for each additional 610 mm width of slab urinal ..................................................................................... 57.60 7.70 8.30 21.20 20294
20295 Chromium plated copper flush pipe and chromium plated brass spreader for single urinal stall or bowl ............................ 229.50 24.20 24.90 61.80 20295
20296 Add to Item 20295 for each additional stall or bowl in a range served from the same cistern .............................................. 123.10 11.50 12.10 33.60 20296
20297 Chromium plated copper flush pipe and sparge pipe n.e. 1 m long for single section slab urinal ......................................... 285.40 27.40 28.10 75.10 20297
20298 Add to Item 20297 for each additional 610 mm width of slab urinal ..................................................................................... 140.00 7.70 8.30 23.00 20298
20299 Grating and waste connection to outlet from urinal channel ditto .......................................................................................... 142.00 13.40 14.00 42.40 20299
20/36
20 FIXTURES AND FITTINGS 20
Item Item
PARTS OF SANITARY FITTINGS (CONT'D)
SHOWER FITTINGS
Take Take
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20300 Shower fitting comprising tap, flexible hose, clamp bracket assembly, slide bar, shower head and
spray handset............................................................................................................................................................................. 502.60 22.30 23.60 70.60 20300
20301 Ditto but with shower mixer in lieu of tap ............................................................................................................................... 664.70 30.00 30.60 97.10 20301
20302 Ditto but with thermo-static shower mixer in lieu of tap ........................................................................................................ 3,088.30 35.10 36.40 141.30 20302
20303 Shower fitting for disabled comprising hand held shower including wall brackets, with 15 mm
diameter chromium plated brass flexible hose mounted on vertical bar minimum 500 mm long capable
to carry a static load of 150kg................................................................................................................................................... 1,353.90 31.90 38.30 110.40 20303
20304 Shower mixer with valves of WSD Water Efficiency Labelling Scheme (WELS) Grade 1, concealed
type complete with shower head and fittings........................................................................................................................... 808.70 26.80 28.10 88.30 20304
20305 Ditto but Grade 2, 3 or 4 type.................................................................................................................................................... 808.70 26.80 28.10 88.30 20305
20306 Shower rose............................................................................................................................................................................... 71.90 7.70 8.30 28.30 20306
20307 Plastic hand spray............................................................................................................................. 83.70 5.70 5.70 12.40 20307
20308 Chromium plated bracket for hand spray including plugging to wall .................................................................................... 101.20 10.20 11.50 23.00 20308
20309 15 mm Diameter chromium plated brass flexible tube, 1.20 m long ...................................................................................... 102.30 6.40 7.70 16.80 20309
20310 Ditto but 1.50 m long ............................................................................................................................................................... 142.30 6.40 7.70 16.80 20310
20311 Shower seat not less than 550 mm wide and 400 mm deep, and fixed to wall including wall
brackets...................................................................................................................................................................................... 1,531.90 33.20 38.30 83.90 20311
WASTE PLUGS AND CHAINS
Take Take
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20312 Rubber or vulcanite waste plug n.e. 64 mm top diameter with chromium plated ring to receive chain
(measured separately) ............................................................................................................................................................... 8.50 2.60 3.80 4.40 20312
20313 Stout chromium plated brass chain ring and screw fixing stud if required n.e. 0.80 m long ................................................. 16.20 5.10 5.70 7.10 20313
20/37
20 FIXTURES AND FITTINGS 20
Item Item
TOILET FITTINGS AND ACCESSORIES
Shower curtain rails or hanging rails in polished chrome, stainless steel or aluminium finish including
Take Take
mounting flanges, caps, curtain rings, brackets and fixing accessories : -
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Per linear metre $ $ $ $
20314 Shower curtain rail or hanging rail .......................................................................................................................................... 31.30 1.10 2.10 2.90 20314
Toilet roll holders including fixing accessories : -
Each
20315 Toilet roll holder (heavy pattern) in stainless steel polished finish or satin finish, or chrome plated finish,
surface mounted........................................................................................................................................................................ 174.10 3.20 7.40 14.70 20315
20316 Locking type ditto ..................................................................................................................................................................... 221.90 4.30 7.40 14.70 20316
20317 Single toilet paper holder ditto.................................................................................................................................................. 120.90 2.10 4.30 11.80 20317
20318 Double toilet roll holder in ditto .............................................................................................................................................. 251.80 2.10 4.30 11.80 20318
20319 Single vitreous china toilet roll holder surface mounted.......................................................................................................... 80.90 2.10 4.30 11.80 20319
20320 Ditto but semi-recessed ............................................................................................................................................................ 99.10 2.10 4.30 11.80 20320
Towel rails in polished chrome, stainless steel or aluminium finish including mounting flanges, caps,
brackets and fixing accessories :-
Each
20321 Towel rail 450 mm long............................................................................................................................................................ 158.00 3.20 6.40 13.20 20321
20322 Ditto 600 mm long.................................................................................................................................................................... 217.00 3.20 6.40 13.20 20322
20323 Ditto 900 mm long.................................................................................................................................................................... 297.00 3.20 6.40 13.20 20323
20/38
20 FIXTURES AND FITTINGS 20
Item Item
TOILET FITTINGS AND ACCESSORIES (CONT'D)
Multi-roll toilet tissue dispenser boxes including fixing accessories : -
Take Take
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20324 Multi-roll toilet tissue dispenser box in plastic........................................................................................................................ 122.80 4.30 9.60 17.60 20324
20325 Ditto in stainless steel................................................................................................................................................................ 284.50 4.30 9.60 17.60 20325
Towel and feminine napkin dispensers in polished chrome, stainless steel or aluminium finish
including mounting flanges, caps, brackets and fixing accessories : -
Each
20326 Towel dispenser, 400 x 600 x 300 mm, surface mounted ....................................................................................................... 527.00 3.20 7.40 17.60 20326
20327 Ditto, 275 x 230 x 110 mm surface mounted .......................................................................................................................... 357.00 3.20 7.40 17.60 20327
20328 Ditto, 380 x 585 x 370 mm surface mounted .......................................................................................................................... 527.00 3.20 7.40 17.60 20328
20329 Feminine napkin disposal, size 190 x 255 x 95 mm................................................................................................................ 210.40 2.10 5.30 11.80 20329
Grab bars in polished chrome finish, stainless steel hair line or mirror finish or aluminium finish
including mounting flanges, caps, tenons plates, brackets and fixing accessories : -
Each
20330 Grab bar 32 - 40 mm diameter, 600 mm long.......................................................................................................................... 259.00 3.20 7.40 17.60 20330
20331 Ditto but 900 mm long.............................................................................................................................................................. 391.60 5.30 10.60 22.10 20331
20332 Grab bar 32 - 40 mm diameter, in L-shaped or two bars arranged in L-shaped configuration,
750 mm by 900 mm in length, capable of carrying a static load of 150kg.............................................................................. 543.60 8.50 15.90 29.40 20332
20/39
20 FIXTURES AND FITTINGS 20
Item Item
TOILET FITTINGS AND ACCESSORIES (CONT'D)
Folding grab rails for disabled toilet, in stainless steel polished hair line or mirror
Take Take
finish, including mounting flanges, caps, tenon plates, brackets and fixing accessories : -
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20333 Folding grab bar 32 - 40mm diameter, in U-shaped of 750mm plan length, swing upwards,
capable of carrying a static load of 150kg................................................................................................................................ 668.50 10.60 21.30 36.80 20333
Grab bars, in non-ferrous metal, with colour resin or similar covering, easy grip
and stain proof coating : -
Each
20334 Grab bar, 32 - 40mm diameter, 600mm long........................................................................................................................... 295.60 3.20 7.40 17.60 20334
20335 Ditto but 900mm long............................................................................................................................................................... 564.20 5.30 10.60 22.10 20335
20336 Grab bar, 32 - 40mm diameter, in L-shaped or two bars arranged in L-shaped configuration,
750mm by 900mm in length, capable of carrying a static load of 150kg................................................................................ 893.80 8.50 15.90 29.40 20336
Folding grab rails for disabled toilet, in non-ferrous metal, with colour resin or similar covering,
easy grip and stain proof coating : -
Each
20337 Folding grab rail, 32 - 40mm diameter, in U-shaped of 750mm plan length, swing upwards,
capable of carrying a static load of 150kg................................................................................................................................ 1,488.40 10.60 21.30 36.80 20337
Shower cubicle screen in clear polycarbonate panel complete with frame, sliding or pivot door panel,
track, fittings and accessories : -
Per square metre
20338 Screen to one-side of shower cubicle, n.e. 1.00 m long and 1.80 m high................................................................................ 1,499.40 21.30 31.90 44.10 20338
20339 Ditto to two sides of shower cubicle, overall n.e. 2.00 m girth and 1.80 m high.................................................................... 2,241.70 31.90 42.50 58.80 20339
20/40
20 FIXTURES AND FITTINGS 20
Item Item
TOILET FITTINGS AND ACCESSORIES (CONT'D)
Accessories in polished chrome, stainless steel or aluminium finish including mounting flanges,
Take Take
caps, brackets and fixing accessories : -
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20340 Tumbler holder.......................................................................................................................................................................... 103.40 2.10 4.30 8.80 20340
20341 Tumbler and tooth brush holder................................................................................................................................................ 121.60 2.10 4.30 8.80 20341
20342 Pair of brackets for 125 mm glass shelves................................................................................................................................ 101.30 4.30 9.60 17.60 20342
20343 Guard rail for 525 x 125 mm glass shelves.............................................................................................................................. 68.30 1.10 2.10 2.90 20343
20344 Washing cream dispenser and plastic soap container.............................................................................................................. 271.70 2.10 4.30 8.80 20344
20345 Soap holder................................................................................................................................................................................ 188.50 2.10 3.20 7.40 20345
20346 Surface mounted liquid soap dispenser.................................................................................................................................... 206.50 2.10 4.30 8.80 20346
20347 Under-counter soap dispenser with 100 mm spout length....................................................................................................... 217.90 2.10 4.30 8.80 20347
20348 Battery operated automatic soap dispenser with infra-red sensor, plastic cover, inspection
window and soap container ...................................................................................................................................................... 484.00 2.10 4.30 8.80 20348
20349 Adjustable mirror for disabled, 450 x 600 mm complete with adjustable pivoted brackets................................................... 263.30 5.30 10.60 22.10 20349
PROPRIETARY DIAPER CHANGING STATION
Proprietary diaper changing station including all necessary accessories in accordance
Take Take
with the manufacturer's recommendations : -
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20350 Proprietary diaper changing station with FDA approved blow-moulded high-density, minimum size
of 900mm length x 500mm width, durable polyethylene with Microban Antimicrobial additive;
equipped with a pneumatic cylinder for controlled opening and closing of bed; secured to back
plate with a concealed full-length steel-on-steel hinge, no hinge structure shall be exposed on
interior and exterior surfaces; applicable for barrier-free accessibility and comply with
ADA regulations; have smooth concave changing area with a nylon safety strap and
two hooks for bags or purses; have universal instruction graphics; safety messages in 6
languages and Braille; static load performance requirements rated to support 250-300 lbs
to comply with ASTM; and the product is to comply with ANSI S117.1, ASTM F2285-04
(formerly ASTM PS125), ANSI Z535.4, German TUV, ASTM G21 and ASTM G22.......................................................... 2,598.60 21.30 42.50 88.20 20350
20/41
20 FIXTURES AND FITTINGS 20
Item Item
BRAILLE AND TACTILE SIGNS
Engraved plastic signs in Braille and tactile information comprising Braille characters, directional arrows, Size (m2)
floor numbers and the like : - n.e. 0.10 - 0.20 - 0.30 -
0.10 0.20 0.30 0.40
A B C D
Each $ $ $ $
20351 Engraved plastic Braille and tactile information signs, 3 mm thick, fixed on handrail, staircases and/or
other locations with adhesive or screws................................................................................................................................... 136.90 205.30 273.70 342.20 20351
20352 Ditto but 6mm thick.................................................................................................................................................................. 161.10 241.60 322.10 402.70 20352
A
Each $
20353 Take down and clear away plastic Braille and tactile information signs of any size.................................................................................................................... 3.20 20353
20354 Take down and set aside for re-use ditto........................................................................................................................................................................................ 6.40 20354
20355 Fix only ditto................................................................................................................................................................................................................................... 14.10 20355
Metal signs in Braille and tactile information comprising Braille characters, directional Size (m2)
arrows, floor numbers and the like :- n.e. 0.001 - 0.002 - 0.003 -
0.001 0.002 0.003 0.004
A B C D
Each $ $ $ $
20356 Stainless steel Braille and tactile information signs, 0.6 mm thick, polished with hair line or
mirror finish, fixed on handrail, staircase and/or other locations with adhesive or screws..................................................... 30.00 46.00 72.60 99.30 20356
A
Each $
20357 Take down and clear away metal Braille and tactile information signs of any size from any position........................................................................................ 5.30 20357
20358 Take down and set aside for re-use ditto........................................................................................................................................................................................ 10.60 20358
20359 Fix only ditto................................................................................................................................................................................................................................... 21.10 20359
20/42
20 FIXTURES AND FITTINGS 20
Item Item
BRAILLE AND TACTILE SIGNS (CONT'D)
Braille and tactile directory maps comprising graphics, logos, letters, numbers, Chinese characters, full stop, commas, and
the like, complete with all necessary accessories in accordance with the manufacturer's recommendations : -
A
Each $
20360 Acid etched stainless steel Braille and tactile directory maps, polished with hair line or mirror finish, fixed to wall,
n.e. 0.20 m2................................................................................................................................................................................................................................................................
11,144.40 20360
20361 Ditto but 0.20 m2 to 0.50 m2..............................................................................................................................................................................................................................................................
22,223.70 20361
20362 Acid etched stainless steel Braille and tactile directory maps, polished with fine grit or hair line finish, fixed to
floor with and including stand, overall height including stand not exceeding 1.0 m above finished floor level;
n.e. 0.20 m2..............................................................................................................................................................................................................................................................
14,663.70 20362
20363 Ditto but 0.20 m2 to 0.50 m2..............................................................................................................................................................................................................................................................
32,523.30 20363
Per square metre
20364 Acid etched stainless steel Braille and tactile directory maps, polished with fine grit or hair line finished, fixed to wall,
exceeding 0.50 m2..............................................................................................................................................................................................................................................................
35,518.80 20364
20365 Ditto but fixed to floor with and including stand, overall height including stand not exceeding 1.0 m above
finished floor level; exceeding 0.50 m2.............................................................................................................................................................................................................................................
46,923.90 20365
Each
20366 Extra over either of Items 20360 to 20365 inclusive for design, supply and installation of proprietary audio system including
provision of connection to nearest power point by a registered electrical worker and providing necessary test certificate........................................................ 4,953.10 20366
Per square metre
20367 Take down and clear away Braille and tactile directory maps....................................................................................................................................................... 127.50 20367
20368 Take down and set aside for re-use ditto........................................................................................................................................................................................ 191.20 20368
20369 Fix only ditto................................................................................................................................................................................................................................... 509.90 20369
20/43
20 FIXTURES AND FITTINGS 20
Item Item
FLAG POLES
Aluminium flag poles complete with all necessary accessories in accordance
Take Take
with the manufacturer's recommendations : -
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20370 Aluminium flag pole 12 - 15 m high, ground anchored (concrete footing measured separately)........................................... 42,737.40 31.90 95.60 504.80 20370
20371 Ditto but 9 -12 m high flag pole................................................................................................................................................ 33,468.20 25.50 85.00 476.80 20371
20372 Add to Item 20370 for each additional 3 m or part thereof in flag pole height....................................................................... 17,605.40 21.30 74.40 476.80 20372
20373 Aluminium flag pole 7 m high, wall mounted including fixing brackets and stainless steel anchor bolts ............................ 23,922.90 21.30 53.10 343.50 20373
20374 Ditto but 6 m high flag pole...................................................................................................................................................... 23,181.20 17.00 42.50 329.50 20374
Replacement parts only : -
Each
20375 Internal halyard, pulleys. etc. for 12 - 15 m high aluminium flag pole including taking down and clear
away existing ............................................................................................................................................................................ 3,328.60 5.30 15.90 126.90 20375
20376 Ditto but for 9 - 12 m high flag pole......................................................................................................................................... 3,205.40 4.30 14.90 112.90 20376
20377 Add to Item 20375 for each additional 3 m or part thereof in flag pole height....................................................................... 717.30 4.30 14.90 98.80 20377
20378 External halyard, pulleys. etc. for 6 or 7 m high flag pole ...................................................................................................... 2,886.20 4.30 13.80 84.80 20378
20/44
20 FIXTURES AND FITTINGS 20
Item Item
PROJECTOR SCREENS
Projection screen including all necessary accessories in accordance with the manufacturer's
Take Take
recommendations : -
Supply down and down and
Fix only
and fix clear set aside
away for re-use
A B C D
Each $ $ $ $
20379 Projector screen, manually operated size : 1,780 x 1,780 mm ................................................................................................ 1,956.20 79.70 92.50 249.40 20379
20380 Projector screen, electrically operated size : 1,600 x 2,130 mm, including provision of connection
to nearest power point by a registered electrical worker.......................................................................................................... 8,317.20 127.60 143.50 320.70 20380
TRAFFIC BARRIER SYSTEM
3m 4.5 m 6m
Traffic barrier system : - straight straight straight
gate arm gate arm gate arm
A B C
Per set $ $ $
20381 Supply and fix traffic barrier system complete with gate arm and ON/OFF push button......................................................................... 18,799.00 19,174.50 19,469.90 20381
20382 Take down and clear away traffic barrier system ...................................................................................................................................... 127.50 159.40 191.20 20382
20383 Take down and set aside for re-use ditto ................................................................................................................................................... 212.50 233.70 255.00 20383
20384 Fix only ditto ............................................................................................................................................................................................... 337.10 351.10 365.10 20384
20/45
Section 21
DEMOUNTABLE PARTITIONS,
DRY WALL AND CUBICLE SYSTEM
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
SECTION 21
DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM
SPECIAL CONDITIONS
Measurement SC21.01 All proprietary demountable partition system (inclusive of security type and fire resisting
of proprietary type partitions) and dry wall shall be measured the area of partition/dry wall over all
demountable framing, irrespective of whether the framing is concealed or exposed to view.
partition system
and dry wall No deduction shall be made for voids or openings not exceeding 0.50 m.
Sound insulation inside the demountable partitions and dry walls shall be measured the
net area where the sound insulation is applied.
All doors shall be measured separately.
Where the demountable partition system or dry wall is described and measured as
fully glazed, it means that the total glazed area of partition / dry wall shall be equal
to or exceeding 80% of the total partition / dry wall area.
Measurement of repairs and alterations to proprietary demountable partition system
and acoustic folding / sliding operable partition system shall be referred to Section 16
- Repairs and Alteration to Specialty Works.
Rates for SC21.02 The rates for demountable partition system and dry wall shall generally include for : -
demountable
partition system (a) Design, fabrication, assembly and erection of the complete system including
and dry wall all necessary riveting, drilling, welding etc. either on Site or off Site as required.
generally
(b) All steel stud framework and components, full or part length panels to
complete length of partitions ordered with natural or other anodized
colour acceptable to the Maintenance Surveyor.
(c) Sound sealing gaskets or other materials acceptable by the Maintenance
Surveyor to all junctions of partitions and dry wall and junctions with other
walls, partitions, window mullions and suspended ceilings.
(d) Treating all exposed wood or veneer surfaces with fire retardant paint.
(e) Treating all fabric surfaces with flame proof treatment.
(f) Aluminium skirting including all types of finishes or black or selected colour
mild steel skirting.
(g) Unless specifically provided otherwise, provisions of finishes to demountable
partitions and dry wall either applied in factories or on Site.
(h) All base, ceiling and abutment fixing.
(i) Forming wants including trimming edges.
21/1
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
SPECIAL CONDITIONS
Rates for SC21.02 (j) All necessary framing and suspension system from structural soffits to suspended
demountable (Cont'd) ceiling level (above the exposed heights for demountable partitions and dry wall)
partition system for holding the demountable partitions and dry wall in place including all necessary
and dry wall stiffening and fixings.
generally
(Cont'd) (k) Any glazing except for fully glazed partition / dry wall as described in Special
Conditions Clause SC21.01.
(l) Provisions of sample panels and applied finishes for selection by the Maintenance
Surveyor.
(m) Submission of design drawings, working details and shop drawings for the
Maintenance Surveyor's approval prior to commencement of installation.
Rates for SC21.03 The rates for proprietary demountable partition system shall further include for : -
proprietary
demountable (a) All framings and edging trims to intermediate, end or adjoining partitions
partition and around door frames, openings and the like.
system
(b) In the case of panel stopped at door height, include additional capping to
exposed upper edge of partition.
(c) For low level partitions, all upper cappings and intermediate stabilizers as
required.
(d) Providing and fixing to concrete structures, walls or fixtures with
anchor bolts, brackets and the like.
(e) Providing manufacturer's guarantee and supplier's warranty.
Rates for SC21.04 The rates for dry wall shall further include for : -
dry wall
(a) All mouldings at edges, skirtings and fixings complete.
(b) Providing and fixing to concrete structures, walls or fixtures with anchor bolts,
brackets and the like.
Rates for SC21.05 The rates for alterations to existing dry wall shall further include for : -
alterations
to existing (a) Taking down and re-fixing existing dry wall, framing, covering materials, etc..
dry wall
(b) Replacement and provision of new compatible fittings and fixing accessories
including additional accessories as necessary, provision of any ancillary
works as may be required.
(c) Modifying existing openings, finishes or covering to suit actual site conditions.
21/2
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
SPECIAL CONDITIONS
Rates for SC21.05 (d) Making good surfaces disturbed.
alterations (Cont'd)
to existing (e) Multi-handling and delivery between the designated locations and storage
dry wall area as directed.
(Cont'd)
(f) Proper protection to the dry wall, framing, fittings and accessories for
storage and re-use.
(g) Modifications on existing framing including provisions of additional framing,
as required.
Rates for SC21.06 The rates for security partitions shall further include for : -
security
partitions (a) All galvanized mild steel framings, bracings, supports and the like rigidly
and stably constructed for security purposes.
(b) Sandwiched mild steel plate security panel.
(c) Providing and fixing all steel or stainless steel anchors or bolts.
(d) Guard bar panel at top when required.
(e) Providing and fixing wood battens or steel brackets for the face coverings.
Rates SC21.07 The rates for fire resisting partitions shall further include for : -
for fire
resisting (a) Supply and installation in accordance with the manufacturer's instructions.
partitions
(b) All galvanized mild steel or stainless steel framings, bracings, supports
and the like rigidly and stably constructed for fire resisting purposes.
(c) Providing and fixing all steel or stainless steel anchors or bolts.
(d) All additional fire resisting panel, components and materials.
(e) Providing and fixing wood battens or steel brackets for the face coverings.
(f) Submission of technical literature, shop drawings, test certificate and
guarantees as required.
21/3
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
SPECIAL CONDITIONS
Rates for SC21.08 The rates for folding or sliding operable partitions shall further include for : -
folding or
sliding operable (a) Supply and installation in accordance with the manufacturer's instructions,
partitions including submission of all necessary design, calculations and shop drawings
as required.
(b) Providing and fixing all accessories, ironmongeries, suspension system, etc.
recommended by the manufacturer.
(c) Cutting mortice or drilling in concrete, brick, stone or other surfaces as
required.
(d) Grouting into new or existing mortice or holes.
(e) Finishing all surfaces, if required.
(f) Making good disturbed surfaces.
(g) Sealing with vinyl acoustical seals and twin-finger contact type vinyl strips
sweep seals as G.S. Items 22.83 and 22.84.
(h) Providing test certificate, operation manual and manufacturer's guarantee.
Rates for SC21.09 The rates for proprietary acoustic folding/sliding operable partition shall further include for : -
proprietary
acoustic folding/ (a) Supply and installation in accordance with the manufacturer's instructions, including
sliding operable submission of all necessary design, calculations and shop drawings as required.
partition
system (b) Providing and fixing all accessories, ironmongeries, suspension system, sound
proof/absorbing materials etc. recommended by the manufacturer.
(c) Cutting mortice or drilling in concrete, brick, stone or other surfaces as required.
(d) Grouting into new or existing mortice or holes.
(e) Finishing all surfaces, if required.
(f) Making good disturbed surfaces.
(g) Sealing with acoustical seals and sweep seals in accordance with the manufacturer's
instructions.
(h) Providing test certificate, operation manual and manufacturer's guarantee.
21/4
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
SPECIAL CONDITIONS
Rates for SC21.10 The rates for proprietary toilet cubicle system, unless otherwise stated, shall include for : -
proprietary
toilet cubicle (a) Supply and installation in accordance with the manufacturer's instructions.
system
(b) Complete systems with lightweight core and solid compact laminate panels
(in conformity to EN 438 standard), finished with high performance surface
veneer sheeting, to doors, partition, pilaster, divisions, etc..
(c) All frames in aluminium (in conformity to EN 6060 standard) coated with corrosion
resistant nylon.
(d) All necessary corrosion resistant nylon-aluminium accessories like hook, toilet roll
holder, and the like, and ironmongeries including adjustable feet, automatic hinges,
snib indicators; coat hooks with door stops and angle brackets.
(e) All types of surface finishes and colours.
(f) All computerized fabrication to ensure excellent edge finish, with no sharp and corners
for safety.
(g) Submission of catalogues, technical literature, shop drawings and manufacturer's
guarantee.
21/5
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
Item Item
PROPRIETARY DEMOUNTABLE PARTITION SYSTEM
Plaster-
board Plywood /
chipboard
panel
Proprietary demountable partition system complete with stud framework, with panel covering panel
covering
12.5 mm (min.) thick and fixed in accordance with the manufacturer's instructions : - covering to
to both both sides
sides of of partition
partition
A B
Per square metre $ $
21001 Partition with panel covering finished with laminated vinyl wall paper..................................................................................................................... 520.30 607.60 21001
21002 Ditto with fabric sheeting.............................................................................................................................................................................................. 647.60 728.40 21002
21003 Ditto with timber veneer sheeting................................................................................................................................................................................. 674.10 782.20 21003
21004 Ditto with laminated plastic sheeting........................................................................................................................................................................... 693.70 803.90 21004
21005 Ditto with 13 mm thick softboard covered with Hessian fabric.................................................................................................................................. 804.10 891.40 21005
21006 Fully glazed partition with glazing in clear glass of any thickness.............................................................................................................................. 644.00 663.00 21006
21007 Ditto in obscure glass of any thickness......................................................................................................................................................................... 676.70 697.00 21007
21008 Ditto in wired glass of any thickness............................................................................................................................................................................ 730.60 752.50 21008
Add to Item 21006 for clear or coloured tempered glass of any thickness.................................................................................................................. 25% 25%
A
Per square metre $
21009 Add to either of Items 21001 to 21005 inclusive for additional sound insulation, 50 mm thick fibreglass insulation
(density not less than 16 kg/m) to proprietary demountable partition system.............................................................................................................................. 30.60 21009
21010 Ditto but of density 48 kg/m.......................................................................................................................................................................................................... 49.20 21010
(Note : - The above Items 21009 to 21010 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
21/6
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
Item Item
PROPRIETARY DEMOUNTABLE PARTITION SYSTEM (CONT'D)
A
Per square metre $
21011 Add to either of Items 21001 to 21005 inclusive for security partitions for Level I security including lined with 1 mm thick
steel plate on both sides, all additional and enhanced framing, fixing, panelling and accessories, in compliance with
sound seal requirement................................................................................................................................................................................................................... 436.60 21011
21012 Add to either of Items 21001 to 21005 inclusive for security partitions for Level II security including lined with 2 mm thick
steel plate on both sides, all additional and enhanced framing, fixing, panelling and accessories, in compliance with
sound seal requirement................................................................................................................................................................................................................... 764.00 21012
21013 Add to either of Items 21001 to 21005 inclusive for security partitions for Level III security including lined with 5 mm thick
steel plate on both sides, all additional and enhanced framing, fixing, panelling and accessories, in compliance with
sound seal requirement................................................................................................................................................................................................................... 1,269.10 21013
21014 Add to either of Items 21001 to 21005 inclusive for fire resisting partitions including all additional and enhanced framing,
fixing, panelling and accessories, in compliance with 1 hour fire resisting requirements............................................................................................................ 218.30 21014
21015 Add to either of Items 21001 to 21005 inclusive for fire resisting security partitions for Level I security including lined with 1 mm
thick steel plate on both sides, all additional framing, fixing, panelling and accessories, in compliance with 1 hour fire resisting
requirements, sound seal requirements........................................................................................................................................................................................... 654.90 21015
21016 Add to either of Items 21001 to 21005 inclusive for fire resisting security partitions for Level II security including lined with
2 mm thick steel plate on both sides, all additional framing, fixing, panelling and accessories, in compliance with 1 hour fire
resisting requirements, sound seal requirements............................................................................................................................................................................ 982.30 21016
21017 Add to either of Items 21001 to 21005 inclusive for fire resisting security partitions for Level III security including lined with
5 mm thick steel plate on both sides, all additional framing, fixing, panelling and accessories, in compliance with 1 hour fire
resisting requirements, sound seal requirements............................................................................................................................................................................ 1,339.90 21017
21018 Add to either of Items 21001 to 21005 inclusive for timber louvre consisting of 45 x 20 mm thick timber framing all round,
10 mm thick timber blades and 25 x 5 mm thick timber architrave (louvre area measured)........................................................................................................ 727.70 21018
21019 Construct ceiling baffle from structural soffit to suspended ceiling level, consisting of 50 mm thick fibreglass insulation
(density 48 kg/m) on both sides of 12.50 mm thick plasterboard framed with metal channel including forming opening of
any size for pipes or ducts and providing all necessary bolts, screws and the like ...................................................................................................................... 764.00 21019
Each
21020 Add to either of Items 21001 to 21005 inclusive for glazed sliding hatch, size 1200 x 450 mm high, consisting of 125 x 25 mm thick
timber framing all round, 6 mm thick clear sheet glass with polished edges and finger holes, P.V.C. tracks housed into framing
at head and cill including forming opening in new partition, providing and fixing of all necessary additional framing
components...................................................................................................................................................................................................................................... 902.50 21020
21/7
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
Item Item
DRY WALL
Dry wall, non-demountable complete with stud framework and panel
Single layer full Double layer full
covering 12.5 mm (min.) thick to both sides of dry wall : -
solid wall solid wall
n.e. 100 mm thick n.e. 200 mm thick
Plywood / Plywood /
Plaster- Plaster-
chip- chip-
board board
board board
panel panel
panel panel
covering covering
covering covering
A B C D
Per square metre $ $ $ $
21021 Dry wall with panel covering without any applied finish........................................................................................................ 246.80 320.80 392.30 510.00 21021
21022 Dry wall with panel covering finished with vinyl wall paper.................................................................................................. 343.00 417.00 545.30 663.00 21022
21023 Ditto with fabric sheeting.......................................................................................................................................................... 391.80 465.80 623.00 740.70 21023
21024 Ditto with timber veneer sheeting............................................................................................................................................. 404.00 478.10 642.40 760.10 21024
21025 Ditto with laminated plastic sheeting....................................................................................................................................... 411.40 485.40 654.00 771.70 21025
21026 Ditto with 13 mm thick softboard covered with Hessian fabric............................................................................................... 440.70 514.70 700.60 818.30 21026
21027 Fully glazed dry wall with glazing in clear glass of any thickness........................................................................................... 277.20 292.00 402.70 426.20 21027
21028 Ditto in obscure glass of any thickness..................................................................................................................................... 289.60 304.50 415.10 438.60 21028
21029 Ditto in wired glass of any thickness........................................................................................................................................ 356.30 371.10 481.80 505.30 21029
Add to Item 21027 for clear or coloured tempered glass of any thickness.............................................................................. 60% 60% 40% 40%
A
Per square metre $
21030 Add to either of Items 21021 to 21026 inclusive for additional sound insulation, 50 mm thick fibreglass insulation
(density not less than 16 kg/m) to single layer dry wall................................................................................................................................................................ 30.60 21030
21031 Ditto but density 48 kg/m3................................................................................................................................................................................................................................................................
49.20 21031
(Note : - The above Items 21030 to 21031 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing.)
21032 Add to either of Items 21021 to 21026 inclusive for additional sound insulation, two layers, each 50 mm thick fibreglass insulation
(density not less than 16 kg/m) to double layer dry wall.............................................................................................................................................................. 61.10 21032
21033 Ditto but density 48 kg/m3.................................................................................................................................................................................................................................................................
98.50 21033
(Note : - The above Items 21032 to 21033 inclusive will only be paid for, if ordered by the Maintenance Surveyor in writing)
21/8
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
Item Item
DRY WALL (CONT'D)
A
Per square metre $
21034 Add to either of Items 21021 to 21026 inclusive for security partitions for Level I security including lined with 1 mm thick steel
plate on both sides, all additional and enhanced framing, fixing, panelling and accessories, in compliance with
sound seal requirement .................................................................................................................................................................................................................. 436.60 21034
21035 Add to either of Items 21021 to 21026 inclusive for security partitions for Level II security including lined with 2 mm thick steel
plate on both sides, all additional and enhanced framing, fixing, panelling and accessories, in compliance with
sound seal requirement .................................................................................................................................................................................................................. 764.00 21035
21036 Add to either of Items 21021 to 21026 inclusive for security partitions for Level III security including lined with 5 mm thick steel
plate on both sides, all additional and enhanced framing, fixing, panelling and accessories, in compliance with
sound seal requirement .................................................................................................................................................................................................................. 1,269.10 21036
21037 Add to either of Items 21021 to 21026 inclusive for single layer fire resisting partitions including all additional and enhanced
framing, fixing, panelling and accessories, in compliance with 1 hour fire resisting requirements ............................................................................................ 218.30 21037
21038 Add to either of Items 21021 to 21026 inclusive for double layer fire resisting partitions including all additional and enhanced
framing, fixing, panelling and accessories, in compliance with 1 hour fire resisting requirements ............................................................................................ 272.90 21038
21039 Add to either of Items 21021 to 21026 inclusive for fire resisting security partitions for Level I security including lined with
1 mm thick steel plate on both sides, all additional and enhanced framing, fixing, panelling and accessories,
in compliance with 1 hour fire resisting requirements, sound seal requirement........................................................................................................................... 654.90 21039
21040 Add to either of Items 21021 to 21026 inclusive for fire resisting security partitions for Level II security including lined with
2 mm thick steel plate on both sides, all additional framing, fixing, panelling and accessories, in compliance with 1 hour
fire resisting requirements, sound seal requirement....................................................................................................................................................................... 982.30 21040
21041 Add to either of Items 21021 to 21026 inclusive for fire resisting security partitions for Level III security including lined with
5 mm thick steel plate on both sides, all additional framing, fixing, panelling and accessories, in compliance with 1 hour fire
resisting requirements, sound seal requirement............................................................................................................................................................................. 1,339.90 21041
21042 Add to either of Items 21021 to 21026 inclusive for timber louvre consisting of 45 x 20 mm thick timber framing all round, 10 mm
thick timber blades and 25 x 5 mm thick timber architrave (louvre area measured).................................................................................................................... 727.70 21042
Each
21043 Add to either of Items 21021 to 21026 inclusive for glazed sliding hatch, size 1200 x 450 mm high, consisting of 125 x 25 mm thick
timber framing all round, 6 mm thick clear sheet glass with polished edges and finger holes, P.V.C. tracks housed into framing at
head and cill including forming opening in new partition, providing and fixing of all necessary additional framing components........................................... 902.50 21043
21/9
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
Item Item
FLUSH DOORS FOR PROPRIETARY DEMOUNTABLE PARTITION SYSTEM
AND DRY WALL
Doors for partitions with or without frames, each leaf size 600 - 900 x 2 100 mm high : - Door type with or
(ironmongery measured separately) without frame
Hard- Hard-
wood wood
hollow solid core
core door door and
and frame frame
A B
Each $ $
21044 Partition door, single leaf, without door frame............................................................................................................................................................. 903.00 974.00 21044
21045 Ditto but with door frame.............................................................................................................................................................................................. 1,247.10 1,259.90 21045
21046 Partition door, double leaf, without door frame........................................................................................................................................................... 1,547.10 1,668.80 21046
21047 Ditto but with door frame.............................................................................................................................................................................................. 1,943.10 1,996.60 21047
A
Each $
21048 Extra over either of Items 21044 to 21047 inclusive for upper portion of door fitted with 6 mm thick clear glass of any size
including forming opening through door, providing all necessary timber framing, timber fillers, glazing compound and the
like (single leaf measured).............................................................................................................................................................................................................. 169.60 21048
21049 Ditto but fitted with 6 mm thick obscure glass panel (ditto)......................................................................................................................................................... 163.40 21049
21050 Ditto but fitted with 6 mm thick wired glass panel (ditto)............................................................................................................................................................. 244.80 21050
21051 Extra over either of Items 21044 to 21047 inclusive for door faced both sides with laminated plastic sheeting in lieu of veneer
(single leaf measured)..................................................................................................................................................................................................................... 56.10 21051
21052 Extra over ditto for door with 15 mm thick plywood blind box, overall size 600 x 340 x 80 mm deep, and lined with 13 mm
thick softboard ................................................................................................................................................................................................................................ 297.60 21052
21053 Extra over ditto for door with timber louvre size 600 x 340 x 80 mm consisting of 45 x 20 mm thick timber framing all round,
10 mm thick timber blades and 25 x 5 mm thick timber architrave ............................................................................................................................................. 230.30 21053
21/10
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
Item Item
FOLDING OR SLIDING OPERABLE PARTITIONS
Folding or sliding operable partitions as G.S. Items 22.81, 22.82(a) and 22.83 to 22.86 complete with
partitions continuously hinged and suspended with swivel hanger or centrally hung suspension Surface finish
system, tracks or guides and all ironmongeries, fittings, partition panels constructed of hardwood Paint Wood Plastic Vinyl
frame and edging with plywood facing : - veneers laminate cloth
A B C D
Per square metre $ $ $ $
21054 Folding or sliding operable partitions, 45 mm thick................................................................................................................ 1,262.90 1,501.20 1,373.40 1,353.90 21054
21055 Extra over for infilling with mineral wool................................................................................................................................ 81.90 81.90 81.90 81.90 21055
Each
21056 Extra over for single pass door.................................................................................................................................................. 444.80 690.30 634.10 525.80 21056
21057 Extra over for double pass door................................................................................................................................................ 881.10 1,440.20 1,275.20 1,045.90 21057
PROPRIETARY ACOUSTIC FOLDING/SLIDING OPERABLE PARTITION SYSTEM
Proprietary acoustic folding/sliding operable partition system, manual-operated, as G.S. Items 22.81, 22.82(b)
and 22.83 to 22.86 complete with partitions continuously hinged and suspended with swivel hanger or centrally
hung and suspended with proprietary suspension system, tracks or guides and all ironmongery, fittings, Surface finish
partition panels constructed of aluminium or steel framing and facing panel, all in accordance with the Wood Plastic Vinyl
manufacturer's recommendation : - veneers laminate cloth
A B C
Per square metre $ $ $
21058 Proprietary acoustic folding/sliding operable partition system of sound transmission class (STC)
of rating not less than 45 dB....................................................................................................................................................................... 3,456.70 3,238.00 3,334.90 21058
21059 Extra over for infilling with mineral wool.................................................................................................................................................. 218.50 218.50 218.50 21059
Each
21060 Extra over for single pass door.................................................................................................................................................................... 6,639.80 6,639.80 6,639.80 21060
21061 Extra over for double pass door.................................................................................................................................................................. 13,279.60 14,189.20 13,279.60 21061
A
Per linear metre $
21062 Extra over for additional track ....................................................................................................................................................................................................... 1,218.80 21062
21/11
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
Item Item
REPAIRS TO DRY WALL AND SUNDRY ITEMS
Take Take
down down
and and set Fix only
clear aside for
away re-use
A B C
Per square metre $ $ $
21063 Single layer full solid dry wall complete with panel covering to both sides of dry wall, with or without applied
finishes, stud framework, infilled sound insulation, fittings and accessories, if any ............................................................................... 19.00 40.50 91.20 21063
21064 Ditto but double layer full solid dry wall.................................................................................................................................................... 25.30 53.20 120.30 21064
21065 Ditto but fully glazed dry wall partition...................................................................................................................................................... 20.30 48.10 126.70 21065
21066 Ditto but as security / fire resisting / fire resisting security partition......................................................................................................... 22.80 57.00 127.90 21066
Each
21067 Hollow or solid core flush door (single leaf measured)............................................................................................................................. 15.20 19.00 21.50 21067
ALTERATION WORKS TO EXISTING DRY WALL
Plywood/
Plaster-
chip-
board
board
panel
panel
covering
covering
A B
Per square metre $ $
21068 Replace panel covering 12.5 mm (min.) thick to one side of existing dry wall, without any applied finish.............................................................. 102.00 124.20 21068
21069 Replace panel covering 12.5 mm (min.) thick to one side of existing dry wall finished with
vinyl wall paper............................................................................................................................................................................................................. 150.10 162.30 21069
21070 Ditto but fabric sheeting................................................................................................................................................................................................ 174.50 189.20 21070
21071 Ditto but timber veneer sheeting................................................................................................................................................................................... 180.70 195.90 21071
21072 Ditto but laminated plastic sheeting............................................................................................................................................................................. 184.30 199.90 21072
21073 Ditto but 13 mm thick softboard covered with Hessian fabric.................................................................................................................................... 199.00 216.10 21073
21/12
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
Item Item
ALTERATION WORKS TO EXISTING DRY WALL (CONT'D)
A
Per square metre $
21074 Alter existing fully glazed partitions to double glazed partition with 6 mm thick clear glass...................................................................................................... 439.30 21074
21075 Ditto but with 6 mm thick obscure glass........................................................................................................................................................................................ 425.00 21075
21076 Ditto but with 6 mm thick wired glass........................................................................................................................................................................................... 583.20 21076
21077 Alter existing dry wall partitions to insert 50 mm thick fibreglass insulation layer (density not less than 16 kg/m)................................................................. 14.10 21077
21078 Ditto but density 48 kg/m.............................................................................................................................................................................................................. 42.26 21078
21079 Construct timber louvre consisting of 45 x 20 mm thick timber framing all round, 10 mm thick timber blades and
25 x 5 mm thick timber architrave including forming opening through existing hollow or solid core flush door
and providing all necessary framing............................................................................................................................................................................................... 881.20 21079
21080 Forming opening of any size through dry wall partition including all necessary partition components...................................................................................... 133.00 21080
Each
21081 Construct glazed sliding hatch, size 1200 x 450 mm high, consisting of 125 x 25 mm thick timber framing all
round, 6 mm thick clear sheet glass with polished edges and finger hole, P.V.C. tracks housed into framing
at head and cill including forming opening in existing dry wall partition, providing and fixing of all necessary
framing components........................................................................................................................................................................................................................ 870.60 21081
21082 Construct 15 mm thick plywood blind box overall size 600 x 340 x 80 mm deep and lined with 13 mm thick softboard......................................................... 617.50 21082
21083 Cutting and trimming partition / dry wall around beams, air-conditioning ducts, etc., including all necessary framing
components and fixings, girth of cut n.e. 1.20 m .......................................................................................................................................................................... 61.30 21083
21084 Scribe infill up to 300 mm wide in 12 mm thick luan plywood to existing window opening for abutting dry wall partition
of any description and height, and finished to match abutting partition / dry wall ...................................................................................................................... 532.50 21084
Per linear metre
21085 Pack top of dry wall partition to ceiling to make up height to 75 mm with painted scantlings plugged and screwed
to concrete soffit or tapped and screwed to grid of suspended ceiling ......................................................................................................................................... 39.50 21085
21086 Construct over dry wall partition n.e. 100 mm wide and up to 300 mm high painted false beam to make up height built up
of 12 mm thick luan plywood and 50 x 50 mm hardwood framing plugged and screwed to concrete soffits or
tapped and screwed to grid of suspended ceiling........................................................................................................................................................................... 186.40 21086
21087 Ditto but 300 - 600 mm high.......................................................................................................................................................................................................... 346.10 21087
21/13
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
Item Item
IRONMONGERY TO PROPRIETARY DEMOUNTABLE PARTITION SYSTEM AND DRY WALL
Supply and fix ironmongery : - Single Double
leaf leaf
door door
A B
Per set $ $
21088 Set of ironmongery comprising cylinder lock, 75 x 100 mm stainless steel hinges, bolts and rubber door stop ...................................................... 233.93 333.00 21088
21089 Set of ironmongery for sliding door comprising mortice locks, flush bolts, sliding door track, channel guide,
hanger, handles, door stop, etc...................................................................................................................................................................................... 1,571.00 3,007.90 21089
PROPRIETARY TOILET CUBICLE SYSTEM
Proprietary toilet cubicle system of impregnated homogeneous core with solid compact laminate panels Take Take
conforming to EN 438, both sides of panels finished with laminated plastic sheeting, and powder coated Supply down down Fix
aluminium frame, headrails and adjustable legs complete with ironmongery, hardware and accessories and and and set only
and all in accordance the manufacturer's instruction. fix clear aside for
away re-use
A B C D
Per set $ $ $ $
21090 Set of one cubicle unit comprising one front panel with one door included,
n.e. 1.00 m wide x n.e. 1.90 m deep x n.e. 2.10 m high........................................................................................................... 1,639.90 63.30 126.70 291.30 21090
21091 Set of one corner cubicle unit comprising one front panel with one door included and one
open-end panel, n.e. 1.00 m wide x n.e. 1.90 m deep x n.e. 2.10 m high................................................................................ 2,733.20 83.60 178.60 364.80 21091
21092 Set of one cubicle unit for disabled comprising one front panel with one door included,
n.e. 1.50 m wide x n.e. 1.90 m deep x n.e. 2.10 m high........................................................................................................... 1,812.90 74.70 162.10 317.90 21092
21093 Set of one corner cubicle unit for disabled comprising one front panel with one door included
and one open-end panel, n.e. 1.50 m wide x n.e. 1.90 m deep x n.e. 2.10 m high.................................................................. 3,021.50 88.70 191.30 388.90 21093
Each
21094 Add to either of Items 21090 to 21093 inclusive for division panel, n.e. 1.90 m deep x n.e. 2.10 m high............................ 1,093.30 48.10 102.60 106.40 21094
Per set
Add to either of Items 21090 to 21093 inclusive for each additional 0.25 m or part thereof in height.................................. 8% - - 8%
21/14
21 DEMOUNTABLE PARTITION, DRY WALL AND CUBICLE SYSTEM 21
Item Item
PROPRIETARY TOILET CUBICLE SYSTEM (CONT'D)
Replacement parts for proprietary toilet cubicle system : - Take Take
Supply down down Fix
and and and set only
fix clear aside for
away re-use
A B C D
Pair $ $ $ $
21095 Hinge (L/H or R/H) .................................................................................................................................................................. 87.30 2.00 4.00 9.10 21095
Each
21096 Adjustable leg ........................................................................................................................................................................... 111.00 2.00 4.00 9.10 21096
21097 Rail fixing rose.......................................................................................................................................................................... 54.60 2.00 4.00 9.10 21097
21098 Angle bracket ............................................................................................................................................................................ 32.80 2.00 4.00 9.10 21098
21099 Headrail 3000mm (L) ............................................................................................................................................................... 229.20 2.00 4.00 9.10 21099
21100 Rail bracket ............................................................................................................................................................................... 58.20 2.00 4.00 9.10 21100
21101 Rail elbow ................................................................................................................................................................................. 29.10 2.00 4.00 9.10 21101
21102 Coat hook .................................................................................................................................................................................. 29.10 2.00 4.00 9.10 21102
21103 Indicator snib (L/H or R/H) ...................................................................................................................................................... 163.70 2.00 4.00 9.10 21103
21104 Rail T connector ....................................................................................................................................................................... 98.20 2.00 4.00 9.10 21104
21/15
Section 22
LANDSCAPE WORK
22 LANDSCAPE WORK 22
SECTION 22
LANDSCAPE WORK
SPECIAL CONDITIONS
Specification SC22.01 This Section shall generally be read and used in conjunction with the Specification
relating to landscape work and new planting works adopted in the Contract.
Due allowance is deemed to have been made in the Contract Percentages for
complying with all requirements as stipulated in the Specification adopted in the
Contract for landscape work and new planting works.
PART I PREPARATORY WORKS
Measurement of SC22.02 Clearing, cutting down and removing from Site rubbish, grass, weed, vines, shrubs,
clearing and undergrowth, etc. and the like including trees not exceeding 95 mm DBH shall be
removing from measured based on the overall surface area covered; and no allowance shall be made
Site rubbish, for surface irregularities or other local peculiarities.
grass, etc.
No deduction shall be made for any area not exceeding 1.00 m.
The items for clearing, cutting down and removing from Site rubbish, grass, weed, vines,
shrubs, undergrowths, etc. and the like including trees not exceeding 95 mm DBH shall not
be paid for if such work is carried out in conjunction with the excavation works, or if
excavation is subsequently carried out by the Contractor at the same location.
Rates for SC22.03 The rates for clearing, cutting and removal of rubbish, grass, weed, vines, shrubs,
clearing and undergrowth and the like including trees not exceeding 95 mm DBH shall include for
removing from cutting the same down to below 25 mm of the level of the ground or sloping ground and
Site rubbish, grubbing out all roots and stumps and filling voids with approved materials.
grass, etc.
All cut materials shall be removed from the Site.
Rates for SC22.04 The rates for removing bamboo protective fencing shall include for taking down
removing bamboo fencing and transporting to a storage area for re-use; or disposal as
bamboo directed by the Maintenance Surveyor including all necessary operations to make
protective good the disturbed areas.
fencing
Rates for taking SC22.05 The rates for taking delivery, spreading, levelling or mixing the manufactured soil
delivery, spreading conditioner, mulch, peat moss, compost, alginate and water absorbing soil additive
and levelling or shall include for loading, and/or transporting from any locations as directed; unloading,
mixing manufactured spreading the mulch evenly on the surface of the soil to the specified depth; or mixing
soil conditioner, mulch, the soil conditioner, peat moss, compost, alginate, water absorbing soil additive into
peat moss, compost, the soil to a specified depth and/or at a specified rate.
alginate and water
absorbing soil additive
22/1
22 LANDSCAPE WORK 22
SPECIAL CONDITIONS
PART I PREPARATORY WORKS
Rates for SC22.06 The rates for supplying, delivering, spreading and levelling drainage aggregate and
supplying, lightweight aggregate shall include for supplying, loading, transporting from any
delivering, location, unloading, spreading, and all multi-handling to final position.
spreading and
levelling drainage
aggregate and
lightweight
aggregate
Rates for SC22.07 The rates for stripping of topsoil in layers not exceeding 150mm thick shall include for
stripping excavating, multi-handling, levelling, grading and trimming surfaces of excavation,
of topsoil depositing the excavated material in spoil heaps including removal to a distance not
exceeding 100 metres, or disposal to an approved dump site when direct, and all
necessary temporary protection.
Rates for SC22.08 The rates for specified underground guying system shall include for supplying,
underground excavating, multi-handling, backfilling, grading, fabricating and fixing the straps, ties,
guying system and other necessary materials as specified in the required location.
PART II LANDSCAPE HARDWORKS
Measurement SC22.09 Ornamental boulders shall be measured as the smallest square or rectangular block
of ornamental laid. In the case of ornamental boulders exceeding 3.00 m, they shall be measured in
boulders the multiple of the largest size and the remainder shall be added. For example, a block
of 10.25 m shall be measured 3 times boulders 1.00 - 3.00 m and the remainders
are 1 times boulders of 0.75 - 1.00 m and 1 times 0.25 - 0.50 m.
Rates for SC22.10 The rates for ornamental boulders shall further include for : -
ornamental
boulders (a) Mobilization, maintenance and demobilization of all plants necessary for the works.
(b) Provision of samples if required.
(c) Supply, loading, transport, unloading, all multiple handling and disposal of
surplus excavated material, storage and placing in final position including all
necessary excavation (footing shall be measured separately).
(d) Marking of ornamental boulders on delivery and removing all marking after
installation as instructed by the Maintenance Surveyor.
(e) Assembling ornamental boulders to any shape, pattern, sculptures as
directed by the Maintenance Surveyor.
Rates for SC22.11 The rates for supplying and laying stepping stones shall include for sourcing and
natural supplying, transporting, unloading, all multi-handling and placing at the final position,
stepping excavation and disposal of soil or surplus material. The stones shall be laid flush to the
stones adjacent finished ground level.
22/2
22 LANDSCAPE WORK 22
SPECIAL CONDITIONS
PART II LANDSCAPE HARDWORKS
Rates for SC22.12 The rates for supplying and laying bricks / concrete blocks for edging to planter beds
edging shall include for supplying, loading, transporting, unloading, placing in position,
to planter including excavation and disposal to allow stable placing, all mortar and bedding,
beds cutting and laying in patterns.
Rates for SC22.13 The rates for lifting existing cast iron tree grilles shall include for lifting the set of cast
lifting cast iron tree grilles and frames out of the tree pit, transporting the grilles to a required
iron tree grilles location and making good any damages resulting from the operation.
Rates for SC22.14 The rates for installing cast iron tree grilles shall include for delivering the set of tree
installing grilles and frames from the storage area or a location as directed by the Maintenance
cast iron Surveyor and placing the grilles in the required position. The rates shall include for all
tree grilles necessary protective coating and painting.
Rates for SC22.15 The rates for removing mild steel tree guards shall include for lifting the tree guard,
removing mild backfilling with suitable materials and making good existing tree pit and transporting
steel tree guards the guard to a location as directed by the Maintenance Surveyor.
Rates for SC22.16 The rates for installing mild steel tree guards shall include for delivery to the Site and
installing mild securing the guard in the required location.
steel tree guards
Rates for SC22.17 The rates for supply and install proprietary tree support and bracing system Cobra
proprietary tree or equivalent shall include supply of all necessary materials including rope, loop,
bracing support expansion insert, antiabrasion hose and shock absorber, transport, storage,
system Cobra manufacturers guarantees or warranties of products etc., submission of method
or equivalent statement, provision of all necessary equipment and safety measures, installation by
qualified specialists, and multi-handlings and adjustment of tree support and bracing
system for valuable problematic trees. The rates shall further include for working at
any height, slope inclination, cable length and any other insurance required.
PART III LANDSCAPE SOFTWORKS
Rates for SC22.18 The rates for landscape softworks shall generally include for : -
landscape
softworks (a) Works executed by approved Specialist Sub-contractors; and
generally
(b) Carrying out establishment works after completion for a period of 12 months
including all works required as stated in Special Conditions Clauses SC22.39
and SC22.40.
22/3
22 LANDSCAPE WORK 22
SPECIAL CONDITIONS
PART III.A LANDSCAPE SOFTWORKS SUPPLY ITEMS
Rates for SC22.19 The rates for supplying of various categories of plant materials shall further include for
supplying supplying the plant material including sourcing, loading, transportation, unloading,
of plant storage, transit protection and placing to the required locations. The rates shall include
materials for all necessary replacement of plant materials found dead or defective.
The grouping of planting materials referred to in this Section of the Schedule is
appended in Annex 'B' to this Schedule.
PART III.B LANDSCAPE SOFTWORKS PLANTING ITEMS
Rates for SC22.20 The rates for landscape softworks - planting items shall further include for : -
landscape
softworks - (a) Application of pre-planting fertilizer to soil mix or topsoil and soil conditioner
planting items to planting areas as specified;
(b) Setting-out and excavating planting pits for root balls, placing the plant in the
pit, backfilling with topsoil or fabricated soil mix;
(c) All necessary supports, staking and tying or guying as specified;
(d) Provision of pre-plant fertilizer and follow-up fertilizer and insect and disease
control treatment, watering and all necessary maintenance and establishment
measures;
Rates for SC22.21 The rates for soiling in landscape areas shall further include for : -
soiling
in landscape (a) Mixing, depositing, compaction, spreading, levelling and beating.
areas
(b) Multiple handling.
(c) Protection of prepared ground against compaction, erosion and siltation.
(d) Importing soils from any source.
(e) Provision of samples.
(f) Additional bulk of material required to allow for compaction and consolidation.
(g) Removing, replacing or making good placed or compacted soiling as required
where soiling material subsequently becomes damaged or unsuitable.
Rates for SC22.22 Further to Special Conditions Clause SC22.21, the rates for fabricated soil mix shall
fabricated soil further include for : -
mix
(a) Testing of samples by an approved laboratory and provision of Certificates
of Analysis of the soil conditioner.
(b) Protection and storage of fabricated soil mix.
22/4
22 LANDSCAPE WORK 22
SPECIAL CONDITIONS
PART III.B LANDSCAPE SOFTWORKS PLANTING ITEMS
Rates for SC22.22 (c) Replacement of fabricated soil mix which are not conforming to the Specification.
fabricated soil (Cont'd)
mix (Cont'd)
Rates for SC22.23 Further to Special Conditions Clause SC22.21, the rates for top soil shall further
top soil include for : -
(a) Protection and storage of top soil.
Rates for pots / SC22.24 The rates for supplying pots and containers shall include for supplying, delivering,
containers placing and removing when instructed.
Rates for SC22.25 The rates for supplying and planting of seasonal flowers shall include:
seasonal flowers
(a) Supplying pots of appropriate sizes, suitable planting medium and plant species as
directed by the Maintenance Surveyor;
(b) Placing the pots as required locations; and
(c) Removing from the Site when instructed.
Rates for SC22.26 The rates for supplying and planting flowering plants from the Orchidaceae family shall include:
Orchidaceae
(a) Supplying pots of appropriate sizes, suitable potting medium and plant species as
directed by the Maintenance Surveyor;
(b) Placing the pots as required locations; and
(c) Removing from the Site when instructed.
Rates for SC22.27 The rates for supplying and fixing in position artificial plants shall include supplying, delivering
artificial plants and placing the plants.
PART III.C TURFING AND GRASSING
Measurement of SC22.28 Hydroseeding, hydro-mulching, broadcasting, sprigging, turfing and the like shall be
hydroseeding, measured as the surface area of the face to be covered and no allowance shall be made
hydro-mulching, for surface irregularities or other local peculiarities. No deduction shall be made for an
broadcasting, area not exceeding 1.00 m.
sprigging and turfing
Rates for SC22.29 The rates for hydroseeding shall further include for : -
hydroseeding
(a) Cleaning ground and scarifying existing soil.
22/5
22 LANDSCAPE WORK 22
SPECIAL CONDITIONS
PART III.C TURFING AND GRASSING
Rates for SC22.29 (b) All materials and equipment necessary for the successful establishment of the
hydroseeding (Cont'd) vegetation.
(Cont'd)
(c) Watering.
(d) Protection of prepared ground surfaces.
(e) Providing and fixing protective layers of biodegradable fabric including allowance for
laps and staples.
(f) Making good areas not covered by approved germinated grass.
(g) First cut and subsequent cuts.
(h) Follow up fertilizer.
(i) Insect and disease control.
(j) Provision of samples and testing certificates.
(k) All necessary operations for satisfactory germination and completion of grass areas as
specified.
Rates for SC22.30 The rates for hydro-mulching shall further include for : -
hydro-mulching
(a) Mobilization and demobilization of all plant and equipment necessary for
the works.
(b) Carrying out survey and checking the existing conditions before applications.
(c) Application by a specialist approved by the Maintenance Surveyor.
(d) Provision of all necessary working platform.
(e) Submission of manufacturer's catalogue.
(f) Providing specialist's guarantee for a period of a minimum of five years.
(g) Providing deed of warranty when required.
(h) All necessary operations for satisfactory germination and completion of grass areas as
specified.
Rates for SC22.31 The rates for turfing and sprigging shall further include for : -
turfing and
sprigging (a) Cleaning ground and scarifying existing soil.
(b) Cultivation and watering.
22/6
22 LANDSCAPE WORK 22
SPECIAL CONDITIONS
PART III.C TURFING AND GRASSING
Rates for SC22.31 (c) Protection of prepared ground surfaces.
turfing and (Cont'd)
sprigging (d) Firming turfs with wooden beaters.
(Cont'd)
(e) Dressing of finely sifted topsoil mix and well brushing into joints.
(f) Adjusting any inequalities in finished levels.
(g) Making good areas not covered by approved germinated grass.
(h) First cut and subsequent cuts.
(i) Preplant fertilizer and follow up fertilizer.
(j) Insect and disease control.
(k) Provision of samples and testing certificates.
(l) All necessary operations for satisfactory germination and completion of grass
areas as specified.
PART III.D TRANSPLANTING
Measurement SC22.32 The DBH of trees to be transplanted shall be measured at a point 1.30 m above ground
generally level.
Rates for SC22.33 The rates for transplanting trees shall further include for : -
transplanting
trees (a) Submission of method statement and programme on all tree works to the
Maintenance Surveyor prior to any transplanting works including excavation,
crown thinning, root pruning and undercutting on the existing tree(s).
(b) Mobilization, maintenance and demobilization of all necessary plant and
equipment for the transplanting operations.
(c) Cleaning soil of existing ground and any contaminated ground including
preparation of tree pit at receptor site and provision of protection of pit.
(d) Root pruning, anchoring and undercutting of the root ball to the required
size and maintenance of root ball system during root pruning period.
(e) Preparation of root ball by wrapping the root ball with hessian or spraying with
approved anti-transpiration spray and keeping the whole plant moist at all time.
(f) Crown thinning of the tree to the required form and shape.
(g) Protection of the tree from mechanical damages, excessive sunlight, wind
and drought including dressing wounds during the whole process of
transplanting.
(h) Provision of tree lifting and pit planting tree including all necessary planting at
the receptor site, immediate maintenance, mulching, watering and cultivation.
22/7
22 LANDSCAPE WORK 22
SPECIAL CONDITIONS
PART III.D TRANSPLANTING
Rates for SC22.33 (i) Provision of metal stakes, ties, guys and guying stakes as required.
transplanting (Cont'd)
trees (j) Replacement of dead / dying tree after transplantation with the same species and
(Cont'd) size of tree.
(k) Back-filling voids and making good disturbed surface to match existing.
Rates for SC22.34 The rates for root pruning plants shall further include for all works to prepare for the uplift
root of the plant at original location, including:
pruning
plants (a) Provision of plants necessary for the works;
(b) Inspection and programming;
(c) Crown thinning;
(d) Root pruning and anchoring; and
(e) Maintenance during root pruning period.
Rates for SC22.35 The rates of temporary storage at the Contractors holding nursery shall cover the cost of
temporary taking up the physical space by individual plant at monthly rate, under the condition that
storage the crowns of the trees / plants shall not touch each other when placed in the nursery. If
the transplanted plant is a tree, the rates shall also cover the cost of the root ball container
per G.S. Item 25.73.5.
PART III.E TREE FELLING AND PRUNING / SURGERY WORKS
Measurement SC22.36 The DBH of trees to be felled shall be measured at a point 1.30 m above ground level.
generally
Pruning to climbers and groundcovers shall be measured the coverage area on plan
irrespective of the planting density and /or height of the plants.
Pruning to whip trees, seedling trees, shrubs, bamboos, herbaceous plants, standard
trees, light standard trees, small conifers and palms (Group A, B, C and E) shall be
measured per number irrespective of the height of the plants.
Rates for SC22.37 The rates for tree pruning / surgery works to existing trees shall further include for operations
pruning / as specified in G.S. Items 25.80 to 25.92.
surgery works
The grouping of planting materials referred to in this Section of the Schedule is appended
in Annex 'B' to this Schedule.
PART IV ESTABLISHMENT WORKS
Measurement SC22.38 The 12-month Establishment Works to be provided for all planting items shall generally be
generally included in the landscape softworks as stated in Special Conditions Clause SC22.18.
22/8
22 LANDSCAPE WORK 22
SPECIAL CONDITIONS
PART IV ESTABLISHMENT WORKS
Measurement SC22.38 Establishment Works shall only be measured where such operations are specifically
generally (Cont'd) (Cont'd) ordered by the Maintenance Surveyor in writing and in a separate Works Order.
Rates for SC22.39 The rates for Establishment Works generally shall include for : -
Establishment
Works (a) The operations as specified, including supply of all necessary materials, provision
of transportation, storage, multi-handling and disposal.
(b) All site inspections to determine the necessary requirements for Establishment
Works.
(c) Replacement of planting materials and regrassing of the same plant species and
heights / sizes where the plants or grass fail to become established or not
conforming to the Specification.
(d) Watering and carrying out operations based on the assessment of the
Establishment Works including weeding, removal of litter, mulching, forking,
aeration, firming up and securing of trees, etc..
(e) Provision of fertilizer and insect / pest and disease control treatment and all
necessary maintenance and establishment measures.
(f) Carrying out pruning of trees and grass cutting.
(g) Submission of monthly Establishment Operations Record.
Rates for SC22.40 The rates for basic establishment works operations for indoor plants shall further include
establishment for : -
operations for
indoor plants (a) Cleaning and polishing all plant leaves with an approved leaf polish at monthly
intervals.
(b) Supply and application of slow-release fertilizer at rate according to G.S.
Item 25.67(d).
(c) Removal of dead leaves and branches, where necessary.
PART V SUNDRIES
Measurement of SC22.41 The item for collect, handle and transport plant specimens shall be measured once for
plant identification each plant species in question as directed by the Maintenance Surveyor.
Measurement of SC22.42 The item for submit written report shall be measured once for each identified plant
written report species.
Rates for plant SC22.43 The rate for collect, handle and transport plant specimens shall include for : -
identification
(a) Storage of specimen in an approved container and other; and
22/9
22 LANDSCAPE WORK 22
SPECIAL CONDITIONS
PART V SUNDRIES
Rates for plant SC22.43 (b) Collection, handling and transporting all collected plant specimen(s) to the
identification (Cont'd) Herbarium of Agriculture, Fisheries and Conservation Department (AFCD).
(Cont'd)
Rates for written SC22.44 The rate for submit written report shall include for : -
report
(a) Completion and submission of necessary information in the appropriate
forms or format as directed by the Maintenance Surveyor.
22/10
22 LANDSCAPE WORK 22
Item Item
PART I - PREPARATORY WORKS
A
Per square metre $
22001 Clear, cut down and remove from Site rubbish, grass, weed, vines, shrubs, undergrowth and the like including
trees n.e. 95 mm DBH, and grubbing up roots and filling void with approved materials, where required,
and making good disturbed surfaces to match existing ................................................................................................................................................................. 24.70 22001
22002 Ditto but to surfaces of slope including clearing up blockages of weep holes and removing all ladders, gang planks, etc. as
required............................................................................................................................................................................................................................................ 27.40 22002
(Note: Items 22001 and 22002 inclusive shall not be paid for if the clearance, cutting down and removal works are carried
out in conjunction with the excavation works, or if excavation works are subsequently carried out by the Contractor at the
same location.)
Per linear metre
22003 Remove bamboo protective fencing............................................................................................................................................................................................... 8.70 22003
Per cubic metre
22004 Supply manufactured soil conditioner............................................................................................................................................................................................ 137.00 22004
22005 Supply mulch................................................................................................................................................................................................................................... 137.00 22005
22006 Supply pine bark mulch.................................................................................................................................................................................................................. 37.40 22006
Per kg
22007 Supply peat moss............................................................................................................................................................................................................................. 6.20 22007
22008 Supply compost............................................................................................................................................................................................................................... 6.20 22008
22009 Supply alginate................................................................................................................................................................................................................................ 87.20 22009
22010 Supply approved water absorbing soil additive.............................................................................................................................................................................. 93.40 22010
Per cubic metre
22011 Take delivery, spread and mix in manufactured soil conditioner.................................................................................................................................................. 18.70 22011
22012 Take delivery, spread and level mulch and pine bark mulch......................................................................................................................................................... 12.50 22012
22/11
22 LANDSCAPE WORK 22
Item Item
PART I - PREPARATORY WORKS (CONT'D)
A
Per square metre $
22013 Take delivery, spread and mix in peat moss, compost, alginate (at rate of 150kg per m2)......................................................................................................................................................
12.50 22013
Per kg
22014 Take delivery, spread and mix in approved water absorbing soil additive.................................................................................................................................... 14.90 22014
Per square metre
22015 Cultivate the surface of the formation up to 300 mm deep............................................................................................................................................................ 5.50 22015
22016 Cultivate the surface of the formation 300 - 450 mm deep............................................................................................................................................................ 8.20 22016
22017 Rip the surface of the formation..................................................................................................................................................................................................... 4.10 22017
22018 Scarify the surface of the formation................................................................................................................................................................................................ 2.70 22018
22019 Grade the surface of the formation................................................................................................................................................................................................. 2.70 22019
22020 Strip topsoil in layers n.e. 150 mm thick........................................................................................................................................................................................ 9.60 22020
Each
22021 Rod out, clear and clean existing weep hole and remove off Site all arising, and fill behind with geotextile fabric pocket with
20 - 25mm coarse aggregate in 150 x 150 x 150 mm overall size................................................................................................................................................. 43.60 22021
22022 Core out 50mm diameter weep hole in existing reinforced concrete or masonry planter wall and fill behind with geotextile
fabric pocket with 20 - 25 mm coarse aggregate in 150 x 150 x 150 mm overall size................................................................................................................. 249.10 22022
Per set
22023 Underground guying system........................................................................................................................................................................................................... 4,003.90 22023
22/12
22 LANDSCAPE WORK 22
Item Item
PART II - LANDSCAPE HARDWORKS Stone Size
N.e. 0.05 - 0.075 - 0.10 -
0.05 m2 0.075 m2 0.10 m2 0.15 m2
A B C D
Each $ $ $ $
22024 Supply and lay 50mm thick natural stepping stones................................................................................................................ 43.60 62.30 93.40 124.50 22024
A
Per cubic metre $
22025 Supply and place natural round river-washed pebbles................................................................................................................................................................... 2,802.10 22025
22026 Supply and place natural pea gravel............................................................................................................................................................................................... 361.20 22026
Per linear metre
22027 Supply and lay 210 x 110 x 50mm coloured concrete blocks edging to planter beds................................................................................................................... 39.20 22027
22028 Supply and lay 220 x 110 x 50mm coloured bricks edging to planter beds.................................................................................................................................. 39.20 22028
22029 Supply and lay 225 x 105 x 70mm bricks in diagonal fashion at planter edge............................................................................................................................. 54.90 22029
Per square metre
22030 Supply and lay 255 x 105 x 70 mm bricks in tree pits................................................................................................................................................................... 280.20 22030
Per linear metre
22031 Supply and fix bamboo protective fencing n.e. 600 mm high to planted and grassed areas......................................................................................................... 40.50 22031
22032 Ditto but 600 - 900 mm high.......................................................................................................................................................................................................... 43.60 22032
22033 Supply and fix plastic lattices of 300 mm high to planted and grassed areas............................................................................................................................... 186.80 22033
22034 Ditto but 600 mm high.................................................................................................................................................................................................................... 373.60 22034
Each
22035 Supply acrylic / aluminum plant labels for tree and climbers........................................................................................................................................................ 24.90 22035
22036 Supply acrylic / aluminum plant labels for shrubs and ground cover plants................................................................................................................................. 24.90 22036
22037 Fix plant labels for trees and climbers............................................................................................................................................................................................ 2.50 22037
22038 Fix plant labels for shrubs and ground cover plants....................................................................................................................................................................... 2.50 22038
22039 Supply, fix and remove weatherproof temporary tree identity label.............................................................................................................................................. 6.20 22039
22/13
22 LANDSCAPE WORK 22
Item Item
PART II - LANDSCAPE HARDWORKS (CONT'D) Size / Diameter
1.00 x 1.05 x 1.50 x 1.20m 1.50m
1.00 m 1.05 m 1.50 m diameter diameter
Type 5 Type 4 Type 1 Type 3 Type 2
A B C D E
Per set $ $ $ $ $
22040 Supply cast iron tree grille....................................................................................................................................... 498.20 373.60 871.80 435.90 498.20 22040
22041 Install cast iron tree grille........................................................................................................................................ 130.80 130.80 180.60 155.70 180.60 22041
A
Per set $
22042 Lift existing cast iron tree grille for re-use..................................................................................................................................................................................... 49.80 22042
22043 Install lifted cast iron tree grille...................................................................................................................................................................................................... 49.80 22043
Each
22044 Supply mild steel tree guard........................................................................................................................................................................................................... 249.10 22044
22045 Install small mild steel tree guard to tree pit.................................................................................................................................................................................. 94.20 22045
Per set
22046 Remove existing mild steel tree guard for re-use........................................................................................................................................................................... 49.80 22046
22047 Install lifted mild steel tree guard................................................................................................................................................................................................... 49.80 22047
Per square metre
22048 Supply and install precast reinforced concrete baffle as root barrier in tree pit............................................................................................................................ 373.60 22048
22049 Supply and install 2mm thick high density PVC sheet as root barrier (Vertically laid)............................................................................................................... 186.80 22049
22050 Supply and install 0.7mm thick high density PVC sheet as root barrier (Horizontally laid)........................................................................................................ 186.80 22050
22/14
22 LANDSCAPE WORK 22
Item Item
PART II - LANDSCAPE HARDWORKS (CONT'D)
(Note : - The following Items 22051 to 22054 will only be paid for, if ordered by the Maintenance Surveyor in writing.)
Supply and install proprietary tree bracing support system "Cobra" or equivalent including all necessary
materials and fittings like rope, loop, expansion insert, anti-abrasion hose and shock absorber etc.
all in accordance with manufacturer's recommendation :
A
Per set $
22051 Cobra plus 2T.................................................................................................................................................................................................................................. 2,745.70 22051
22052 Cobra plus 4T.................................................................................................................................................................................................................................. 3,144.10 22052
22053 Cobra 8T.......................................................................................................................................................................................................................................... 5,408.00 22053
22054 Cobra Ultrastatic............................................................................................................................................................................................................................. 5,306.60 22054
ORNAMENTAL BOULDERS
Ornamental boulders shall be natural, rounded rocks of various overall sizes and types as
specified and selected by the Maintenance Surveyor, supply, lay or assemble in mortar, Boulder size (m)
place and sit in soil base or concrete base (concrete base measured separately). n.e. 0.25 0.25 - 0.50 0.50 - 0.75 0.75 - 1.00 1.00 - 3.00
A B C D E
Each $ $ $ $ $
22055 Granite..................................................................................................................................................................... 228.40 690.60 883.70 1,054.50 2,435.30 22055
22056 Great Lake rock....................................................................................................................................................... 285.40 988.50 1,541.70 1,954.40 3,016.60 22056
22057 Serpentine boulders................................................................................................................................................. 251.20 828.60 1,251.30 1,611.50 2,627.90 22057
22058 Ying rock................................................................................................................................................................. 216.90 607.00 784.20 1,002.80 2,170.60 22058
22059 Yellow soap stone................................................................................................................................................... 274.20 954.30 1,388.60 1,788.60 2,885.60 22059
A
Per cubic metre $
22060 Take down and clear away ornamental boulders in any sizes........................................................................................................................................................ 264.90 22060
22061 Take down and set aside for re-use ditto........................................................................................................................................................................................ 113.60 22061
22062 Lay only in concrete or soil (concrete base measured separately) ditto......................................................................................................................................... 190.20 22062
22/15
22 LANDSCAPE WORK 22
Item Item
PART III.A - LANDSCAPE SOFTWORKS - SUPPLY ITEMS
Supply the following plants : -
Group A Group B Group C Group D Group E Group F Group G
A B C D E F G
Each $ $ $ $ $ $ $
22063 Seedling tree........................................................................................................................ 12.40 18.70 24.90 14.90 22.40 37.40 18.70 22063
22064 Whip..................................................................................................................................... 18.70 24.90 37.40 22.40 32.40 47.30 24.90 22064
22065 Light standard tree............................................................................................................... 74.70 124.50 186.80 99.60 174.40 305.10 124.50 22065
22066 Standard tree........................................................................................................................ 124.50 186.80 373.60 174.40 298.90 498.20 186.80 22066
22067 Heavy standard tree............................................................................................................. 373.60 622.70 1,494.50 498.20 - - 622.70 22067
22068 Semi-mature tree of stem diameter n.e. 200 mm................................................................ 3,113.50 3,736.20 6,227.00 3,487.10 - - 3,736.20 22068
A
Each $
22069 Extra over Item 22068A for each addition of 50mm or part thereof in stem diameter................................................................................................................. 853.10 22069
22070 Extra over Item 22068B for each addition of 50mm or part thereof in stem diameter.................................................................................................................. 1,027.50 22070
22071 Extra over Item 22068C for each addition of 50mm or part thereof in stem diameter................................................................................................................. 1,868.10 22071
22072 Extra over Item 22068D for each addition of 50mm or part thereof in stem diameter................................................................................................................. 996.30 22072
22073 Extra over Item 22068G for each addition of 50mm or part thereof in stem diameter................................................................................................................. 1,027.50 22073
22074 Extra over trees in clipped form with overall height n.e. 1200mm................................................................................................................................................ 373.60 22074
22075 Ditto - overall height 1200 -1500mm............................................................................................................................................................................................. 622.70 22075
22076 Ditto - overall height 1500 -1800mm............................................................................................................................................................................................. 871.80 22076
Group A Group B Group C Group D
A B C D
Each $ $ $ $
22077 Small conifers............................................................................................................................................................................ 249.10 435.90 311.40 342.50 22077
22078 Large conifers............................................................................................................................................................................ 996.30 1,494.50 1,245.40 1,432.20 22078
22/16
22 LANDSCAPE WORK 22
Item Item
PART III.A - LANDSCAPE SOFTWORKS - SUPPLY ITEMS (CONT'D)
Supply the following plants : - (Cont'd)
A
Each $
22079 Extra over Item 22078A for each addition of 300mm high or part thereof................................................................................................................................... 124.50 22079
22080 Extra over Item 22078B for each addition of 300mm high or part thereof................................................................................................................................... 199.30 22080
22081 Extra over Item 22078C for each addition of 300mm high or part thereof................................................................................................................................... 161.90 22081
22082 Extra over Item 22078D for each addition of 300mm high or part thereof................................................................................................................................... 186.80 22082
22083 Extra over Conifers in clipped form with overall height n.e. 1200mm......................................................................................................................................... 373.60 22083
22084 Ditto - overall height 1200-1500mm.............................................................................................................................................................................................. 622.70 22084
22085 Ditto - overall height 1500-1800mm.............................................................................................................................................................................................. 871.80 22085
Group A Group B Group C Group D Group E Group F
A B C D E F
Each $ $ $ $ $ $
22086 Small palms........................................................................................................................................... 373.60 186.80 124.50 224.20 99.60 155.70 22086
22087 Medium palms....................................................................................................................................... 622.70 435.90 249.10 435.90 224.20 323.80 22087
22088 Large palms............................................................................................................................................ 1,868.10 1,120.80 622.70 996.30 - 840.60 22088
A
Each $
22089 Extra over Item 22088A for each addition of 150mm high or part thereof................................................................................................................................... 249.10 22089
22090 Extra over Item 22088B for each addition of 300mm high or part thereof................................................................................................................................... 373.60 22090
22091 Extra over Item 22088C for each addition of 300mm high or part thereof................................................................................................................................... 186.80 22091
22092 Extra over Item 22088D for each addition of 500mm high or part thereof................................................................................................................................... 186.80 22092
22093 Extra over Item 22088F for each addition of 300mm high or part thereof.................................................................................................................................... 249.10 22093
22094 Small shrubs, 150 - 300mm high, 150 - 250 mm spread............................................................................................................................................................... 10.00 22094
22095 Small shrubs, 300 - 450mm high, 250 - 400 mm spread............................................................................................................................................................... 14.30 22095
22096 Small shrubs, 450 - 600mm high, 400 - 550 mm spread............................................................................................................................................................... 15.60 22096
22/17
22 LANDSCAPE WORK 22
Item Item
PART III.A - LANDSCAPE SOFTWORKS - SUPPLY ITEMS (CONT'D)
Supply the following plants : - (Cont'd)
A
Each $
22097 Large shrubs, 600 - 900mm high, 550 - 750 mm spread............................................................................................................................................................... 19.90 22097
22098 Large shrubs, 900 - 1200mm high, 750 - 1000 mm spread........................................................................................................................................................... 62.30 22098
22099 Large shrubs exc. 1200mm high .................................................................................................................................................................................................... 124.50 22099
22100 Extra over small shrubs in clipped form......................................................................................................................................................................................... 186.80 22100
22101 Extra over large shrubs in clipped form......................................................................................................................................................................................... 373.60 22101
22102 Herbaceous plants, 150 - 300mm high, 100 - 200mm spread....................................................................................................................................................... 12.40 22102
22103 Herbaceous plants, 300 - 450mm high, 200 - 400mm spread....................................................................................................................................................... 12.40 22103
22104 Herbaceous plants, 450 - 600mm high, 400 - 600mm spread....................................................................................................................................................... 14.30 22104
22105 Ground cover plants (except Wedelia trilobata), 100 - 200mm high, 100 - 200mm spread ........................................................................................................ 5.60 22105
22106 Ground cover plants (except Wedelia trilobata), 200 - 300mm high, 200 - 450mm spread ........................................................................................................ 7.50 22106
22107 Ground cover plants (except Wedelia trilobata), 300 - 450mm high, 450 - 700mm spread ........................................................................................................ 9.40 22107
22108 Wedelia trilobata ground cover 100 - 200mm high, 200 - 300mm spread.................................................................................................................................... 1.90 22108
22109 Climbers of shoot length 600 - 1500mm........................................................................................................................................................................................ 14.90 22109
22110 Climbers of shoot length 1500 - 2500mm...................................................................................................................................................................................... 29.90 22110
22111 Bamboos 500 - 1200mm................................................................................................................................................................................................................. 19.90 22111
22112 Bamboos 1200 - 1500mm............................................................................................................................................................................................................... 37.40 22112
22113 Bamboos 1500 - 2100mm............................................................................................................................................................................................................... 62.30 22113
22114 Extra over Item 22113A for each addition of 600mm high or part thereof................................................................................................................................... 62.30 22114
22115 Aquatic plants, n.e. 450mm high.................................................................................................................................................................................................... 12.40 22115
22116 Aquatic plants, 450 - 600mm high................................................................................................................................................................................................. 18.70 22116
22117 Aquatic plants, exc. 600mm high................................................................................................................................................................................................... 24.90 22117
22/18
22 LANDSCAPE WORK 22
Item Item
PART III.A - LANDSCAPE SOFTWORKS - SUPPLY ITEMS (CONT'D)
Supply, place and remove (when instructed) the following acclimatized indoor plants : -
Group A Group B Group C Group D Group E Group F Group G
A B C D E F G
Each $ $ $ $ $ $ $
22118 Standard tree........................................................................................................................ 137.00 205.50 411.00 186.80 330.00 548.00 205.50 22118
22119 Heavy standard tree............................................................................................................. 411.00 685.00 1,643.90 548.00 - - 685.00 22119
22120 Semi-mature tree.................................................................................................................. 3,424.80 4,109.80 6,849.60 3,835.80 - - 4,109.80 22120
22121 Small conifer........................................................................................................................ 274.00 479.50 342.50 373.60 - - - 22121
22122 Large conifer........................................................................................................................ 1,095.90 1,643.90 1,369.90 1,506.90 - - - 22122
22123 Small palm........................................................................................................................... 411.00 205.50 137.00 246.60 109.60 171.90 - 22123
22124 Medium palm....................................................................................................................... 685.00 479.50 274.00 479.50 246.60 356.20 - 22124
22125 Large palm........................................................................................................................... 2,054.90 1,232.90 685.00 1,095.90 - 890.50 - 22125
A
Each $
22126 Extra over Item 22125A for each addition of 150mm high or part thereof................................................................................................................................... 274.00 22126
22127 Extra over Item 22125B for each addition of 300mm high or part thereof................................................................................................................................... 411.00 22127
22128 Extra over Item 22125C for each addition of 300mm high or part thereof................................................................................................................................... 205.50 22128
22129 Extra over Item 22125D for each addition of 500mm high or part thereof................................................................................................................................... 205.50 22129
22130 Extra over Item 22125F for each addition of 300mm high or part thereof.................................................................................................................................... 274.00 22130
22131 Shrubs, climbers and herbaceous plants n.e. 600mm high above ground level with minimum 200mm diameter pot................................................................ 43.60 22131
22132 Shrubs, climbers and herbaceous plants 600 - 1200mm high above ground level with minimum 300mm diameter pot........................................................... 199.30 22132
22133 Shrubs, climbers and herbaceous plants 1200 - 1800mm high above ground level with minimum 400mm diameter pot......................................................... 647.60 22133
22134 Shrubs, climbers and herbaceous plants exc. 1800mm high above ground level with minimum 450mm diameter pot............................................................. 1,531.80 22134
Per cubic metre
22135 Supply, spread and mix in potting medium.................................................................................................................................................................................... 12.40 22135
22/19
22 LANDSCAPE WORK 22
Item Item
PART III.A - LANDSCAPE SOFTWORKS - SUPPLY ITEMS (CONT'D)
Supply, place and remove (when instructed) the following acclimatized indoor plants : - (Cont'd)
A
Each $
22136 Supply and plant plants in clipped form of overall height n.e. 1200mm....................................................................................................................................... 411.00 22136
22137 Ditto - overall height 1200 - 1500mm............................................................................................................................................................................................ 685.00 22137
22138 Ditto - overall height 1500 - 1800mm............................................................................................................................................................................................ 1,095.90 22138
Plant the following plants : -
Each
22139 Plant seedling tree........................................................................................................................................................................................................................... 4.40 22139
22140 Collect seedling tree, whip and pot plant from the Government Nursery or other site and deliver to the Site............................................................................ 1.20 22140
22141 Plant whip........................................................................................................................................................................................................................................ 6.20 22141
22142 Plant light standard tree.................................................................................................................................................................................................................. 62.30 22142
22143 Plant standard tree........................................................................................................................................................................................................................... 93.40 22143
22144 Plant heavy standard tree................................................................................................................................................................................................................ 124.50 22144
22145 Plant semi-mature tree n.e. 200 mm stem diameter....................................................................................................................................................................... 373.60 22145
22146 Extra over Item 22145 for each addition of 50 mm or part thereof in stem diameter................................................................................................................... 62.30 22146
22147 Plant small conifer.......................................................................................................................................................................................................................... 31.10 22147
22148 Plant large conifer........................................................................................................................................................................................................................... 124.50 22148
22149 Extra over Item 22148 for each addition of 600 mm high or part thereof..................................................................................................................................... 62.30 22149
22150 Plant small palm.............................................................................................................................................................................................................................. 24.90 22150
22151 Plant medium palm......................................................................................................................................................................................................................... 43.60 22151
22152 Plant large palm............................................................................................................................................................................................................................... 124.50 22152
22153 Extra over Item 22152 for each addition of 1000 mm high or part thereof................................................................................................................................... 62.30 22153
22/20
22 LANDSCAPE WORK 22
Item Item
PART III.B - LANDSCAPE SOFTWORKS - PLANTING ITEMS
A
Per cubic metre $
22154 Supply decomposed granite sub-soil filling materials, wheel, spread, level and compact in layers 75 mm thick to flat areas
and slopes or filled into flower bed or flower boxes, including trimming and beating surface and forming mitres and curves................................................. 114.20 22154
22155 Supply fabricated soil mix ditto...................................................................................................................................................................................................... 148.70 22155
22156 Supply top soil ditto........................................................................................................................................................................................................................ 200.70 22156
22157 Supply special soil mix composed of 1 part selected soil, 1 part sand and 1 part fine aggregate mixed thoroughly ditto........................................................... 127.50 22157
Plant the following plants : -
A
Each $
22158 Plant small shrub............................................................................................................................................................................................................................. 3.70 22158
22159 Plant large shrub.............................................................................................................................................................................................................................. 6.20 22159
22160 Plant herbaceous plant.................................................................................................................................................................................................................... 3.10 22160
22161 Plant ground cover plant................................................................................................................................................................................................................. 2.50 22161
22162 Plant climber with shortest shoot 600 - 1500 mm length.............................................................................................................................................................. 5.00 22162
22163 Plant climber with shortest shoot 1500 - 2500 mm length............................................................................................................................................................ 10.00 22163
22164 Plant bamboo of height n.e. 1200 mm ........................................................................................................................................................................................... 6.20 22164
22165 Plant bamboo of height 1200 - 2100 mm....................................................................................................................................................................................... 12.50 22165
22166 Extra over Item 22165 for each addition of 600 mm high or part thereof..................................................................................................................................... 6.20 22166
22167 Plant aquatic plant........................................................................................................................................................................................................................... 6.20 22167
Supply the following pots or containers and remove from the Site when instructed by the Maintenance Surveyor
(supply of plants is measured separately) : -
Each
22168 Plastic pot 250 - 300mm diameter.................................................................................................................................................................................................. 12.50 22168
22169 Plastic pot 300 - 900mm diameter.................................................................................................................................................................................................. 24.90 22169
22170 Glazed ceramic pot 400 - 450mm diameter.................................................................................................................................................................................... 99.70 22170
22171 Glazed ceramic pot 450 - 550mm diameter.................................................................................................................................................................................... 124.60 22171
22172 Glazed ceramic pot 550 - 1000mm diameter.................................................................................................................................................................................. 186.80 22172
22/21
22 LANDSCAPE WORK 22
Item Item
PART III.B - LANDSCAPE SOFTWORKS - PLANTING ITEMS (CONT'D)
Supply the following pots or containers and remove from the Site when instructed by the Maintenance Surveyor
(supply of plants is measured separately) : - (Cont'd)
A
Each $
22173 Unglazed pot in variety of shapes and colours with perimeter of inner rim n.e. 2000mm........................................................................................................... 24.90 22173
22174 Unglazed pot in variety of shapes and colours with perimeter of inner rim 2000 - 4000mm....................................................................................................... 24.90 22174
22175 Unglazed pot in variety of shapes and colours with perimeter of inner rim 4000 - 6000mm....................................................................................................... 37.40 22175
22176 Unglazed pot in variety of shapes and colours with perimeter of inner rim 6000 - 8000mm....................................................................................................... 37.40 22176
22177 Polished, coloured fibre-glass pot in variety of shapes and colours with perimeter of inner rim n.e. 2000mm........................................................................... 498.20 22177
22178 Polished, coloured fibre-glass pot in variety of shapes and colours with perimeter of inner rim 2000 - 4000mm...................................................................... 622.70 22178
22179 Polished, coloured fibre-glass pot in variety of shapes and colours with perimeter of inner rim 4000 - 6000mm...................................................................... 747.20 22179
22180 Polished, coloured fibre-glass pot in variety of shapes and colours with perimeter of inner rim 6000 - 8000mm...................................................................... 871.80 22180
22181 Coloured fibre-glass pots in 'granolithic' finish in variety of shapes with drain holes; bottom recessed for stand; concealed
lifting eyebolts and colours with inner rim n.e. 2000mm.............................................................................................................................................................. 747.20 22181
22182 Coloured fibre-glass pots in 'granolithic' finish in variety of shapes with drain holes; bottom recessed for stand; concealed
lifting eyebolts and colours with inner rim 2000 - 4000mm.......................................................................................................................................................... 871.80 22182
22183 Coloured fibre-glass pots in 'granolithic' finish in variety of shapes with drain holes; bottom recessed for stand; concealed
lifting eyebolts and colours with inner rim 4000 - 6000mm.......................................................................................................................................................... 996.30 22183
22184 Coloured fibre-glass pots in 'granolithic' finish in variety of shapes with drain holes; bottom recessed for stand; concealed
lifting eyebolts and colours with inner rim 6000 - 8000mm.......................................................................................................................................................... 1,245.40 22184
22185 Coloured fibre-glass pots in decorative molding finish in variety of shapes with drain holes; bottom recessed for stand;
concealed lifting eyebolts and colours with inner rim n.e. 2000mm............................................................................................................................................. 498.20 22185
22186 Coloured fibre-glass pots in decorative molding finish in variety of shapes with drain holes; bottom recessed for stand;
concealed lifting eyebolts and colours with inner rim 2000 - 4000mm........................................................................................................................................ 622.70 22186
22187 Coloured fibre-glass pots in decorative molding finish in variety of shapes with drain holes; bottom recessed for stand;
concealed lifting eyebolts and colours with inner rim 4000 - 6000mm........................................................................................................................................ 747.20 22187
22188 Coloured fibre-glass pots in decorative molding finish in variety of shapes with drain holes; bottom recessed for stand;
concealed lifting eyebolts and colours with inner rim 6000 - 8000mm........................................................................................................................................ 871.80 22188
22189 Natural granite pots in variety of shapes, finishes and colours with stands and inner rim n.e. 2000mm..................................................................................... 498.20 22189
22190 Natural granite pots in variety of shapes, finishes and colours with stands and inner rim 2000 - 4000mm................................................................................ 622.70 22190
22191 Natural granite pots in variety of shapes, finishes and colours with stands and inner rim 4000 - 6000mm................................................................................ 747.20 22191
22192 Natural granite pots in variety of shapes, finishes and colours with stands and inner rim 6000 - 8000mm................................................................................ 871.80 22192
22/22
22 LANDSCAPE WORK 22
Item Item
PART III.B - LANDSCAPE SOFTWORKS - PLANTING ITEMS (CONT'D)
Supply the following pots or containers and remove from the Site when instructed by the Maintenance Surveyor
(supply of plants is measured separately) : - (Cont'd)
A
Each $
22193 Concrete pots in variety of shapes with perimeter of inner rim n.e. 2000mm............................................................................................................................... 622.70 22193
22194 Concrete pots in variety of shapes with perimeter of inner rim 2000 - 4000mm.......................................................................................................................... 747.20 22194
22195 Concrete pots in variety of shapes with perimeter of inner rim 4000 - 6000mm.......................................................................................................................... 871.80 22195
22196 Concrete pots in variety of shapes with perimeter of inner rim 6000 - 8000mm.......................................................................................................................... 996.30 22196
22197 Stainless steel plant containers in variety of shapes with perimeter of inner rim n.e. 2000mm................................................................................................... 622.70 22197
22198 Stainless steel plant containers in variety of shapes with perimeter of inner rim 2000 - 4000mm............................................................................................... 747.20 22198
22199 Stainless steel plant containers in variety of shapes with perimeter of inner rim 4000 - 6000mm............................................................................................... 871.80 22199
22200 Stainless steel plant containers in variety of shapes with perimeter of inner rim 6000 - 8000mm............................................................................................... 996.30 22200
22201 Supply and plant seasonal flower 150 - 300mm high, 150 - 300mm spread including appropriate sized pot with tray............................................................. 24.90 22201
22202 Supply and plant seasonal flowers 300 - 450mm high, 300 - 400mm spread including appropriate sized pot with tray............................................................ 37.40 22202
22203 Supply and plant seasonal flowers 450 - 600mm high, 400 - 550mm spread including appropriate sized pots with trays......................................................... 62.30 22203
22204 Supply and plant seasonal flowers 600 - 900mm high, 550 - 750mm spread including appropriate sized pots with trays......................................................... 87.20 22204
22205 Supply and plant flowering plant from the Orchidaceae family with appropriate sized pot with tray......................................................................................... 99.70 22205
Supply and fix in position artificial plants as described and specified including Height
appropriate sized pots with trays : - N.e 900 - 1200 - 1500 -
900mm 1200mm 1500mm 1800mm
A B C D
Each $ $ $ $
22206 Trees.......................................................................................................................................................................................... 249.10 622.70 996.30 3,736.20 22206
A
Each $
22207 Extra over Item 22206D for each addition of 1000mm height or part thereof.............................................................................................................................. 1,245.40 22207
22/23
22 LANDSCAPE WORK 22
Item Item
PART III.B - LANDSCAPE SOFTWORKS - PLANTING ITEMS (CONT'D)
Supply and fix in position artificial plants as described and specified including
appropriate sized pots with trays : - (Cont'd)
Height
N.e 300 - 600 - 900 -
300mm 600mm 900mm 1200mm
A B C D
Each $ $ $ $
22208 Shrubs........................................................................................................................................................................................ 124.60 186.80 249.10 373.60 22208
Height
N.e 1000 - 1500 - 2000 - 3000 -
1000mm 1500mm 2000mm 3000mm 4000mm
A B C D E
Each $ $ $ $ $
22209 Palms....................................................................................................................................................................... 373.60 498.20 747.20 996.30 1,245.40 22209
A
Each $
22210 Extra over Item 22209E for each addition of 1000mm height or part thereof.............................................................................................................................. 249.10 22210
Height
500 - 1200 - 1500 -
1200mm 1500mm 2100mm
A B C
Each $ $ $
22211 Bamboo........................................................................................................................................................................................................ 311.40 373.60 498.20 22211
A
Each $
22212 Extra over Item 22211C for each addition of 600mm height or part thereof................................................................................................................................ 249.10 22212
22/24
22 LANDSCAPE WORK 22
Item Item
PART III.B - LANDSCAPE SOFTWORKS - PLANTING ITEMS (CONT'D)
Supply and fix in position artificial plants as described and specified including Height
appropriate sized pots with trays : - (Cont'd) N.e 1200 - 1500 - 2100 - 2700 -
1200mm 1500mm 2100mm 2700mm 3600mm
A B C D E
Each $ $ $ $ $
22213 Conifers................................................................................................................................................................... 373.60 498.20 747.20 996.30 1,245.40 22213
A
Each $
22214 Extra over Item 22213E for each addition of 500mm height or part thereof................................................................................................................................. 249.10 22214
200 - 300 -
Height
300mm 450
200 - 450 -
Spread
450mm 700mm
A B
Each $ $
22215 Ground covers............................................................................................................................................................................................................... 37.40 62.30 22215
Shoot Length
N.e 600 - 900 - 1200 -
600mm 900mm 1200mm 1800mm
A B C D
Each $ $ $ $
22216 Climbers.................................................................................................................................................................................... 37.40 49.80 62.30 87.20 22216
A
Per square metre $
22217 Turf (decorative)............................................................................................................................................................................................................................. 622.70 22217
22/25
22 LANDSCAPE WORK 22
Item Item
PART III.C - TURFING AND GRASSING
Hydro-mulching on sprayed concrete or other non-soil surface with slope gradient of not more than 70 degrees,
all in strict accordance with manufacturer's instructions : -
A
Per square metre $
22218 Hydro-mulching on spray-concrete or other non-soil surface........................................................................................................................................................ 1,090.30 22218
22219 Broadcast seed................................................................................................................................................................................................................................. 10.00 22219
22220 Supply and lay grass sprigs (grass species excluding Cynodon dactylon 'Tifway T419')............................................................................................................. 24.40 22220
22221 Supply and lay grass sprigs of species Cynodon dactylon 'Tifway T419'...................................................................................................................................... 31.50 22221
22222 Supply and lay turf (grass species excluding Cynodon dactylon 'Tifway T419').......................................................................................................................... 43.60 22222
22223 Supply and lay Cynodon dactylon 'Tifway T419' species turf ...................................................................................................................................................... 49.80 22223
22224 Lay only turfs on flat or slopes areas.............................................................................................................................................................................................. 19.20 22224
22225 Spray hydroseeding to surfaces of slope n.e. 30 degree from horizontal....................................................................................................................................... 29.30 22225
22226 Ditto exceeding 30 degree from horizontal ................................................................................................................................................................................... 32.40 22226
PART III.D - TRANSPLANTING
Transplant the following plants obtained from an existing or a designated location to any distance from or to Site including all
necessary excavation, backfilling, pruning, removing surplus excavated material from Site, loading, transporting, unloading,
tree surgery work, cultivating, planting firming, staking, protecting and watering as required for new works by the Specification
and as directed by the Maintenance Surveyor : -
A
Each $
22227 Groundcovers, herbaceous, climbers, small shrubs or any height and spread............................................................................................................................... 12.50 22227
22228 Large shrubs of any height and spread / bamboos n.e. 1200mm height........................................................................................................................................ 24.90 22228
22229 Bamboos exc. 1200mm height........................................................................................................................................................................................................ 62.30 22229
Location Location
within outside
the Site the Site
A B
Each $ $
22230 Transplant trees/palms/conifers 150 - 450 mm diameter at breast height................................................................................................................... 1,833.90 2,727.40 22230
22231 Ditto 450 - 900 mm diameter at breast height.............................................................................................................................................................. 3,686.70 4,674.20 22231
22232 Ditto 900 - 1,350 mm diameter at breast height........................................................................................................................................................... 4,871.80 8,163.50 22232
22233 Ditto 1,350 - 1,800 mm diameter at breast height........................................................................................................................................................ 16,552.40 26,333.40 22233
22234 Ditto 1,800 - 2,250 mm diameter at breast height........................................................................................................................................................ 32,446.50 47,258.90 22234
22/26
22 LANDSCAPE WORK 22
Item Item
PART III.D - TRANSPLANTING (CONT'D) Slope Inclination
exceeding
30- 45
45
A B
Each $ $
22235 Extra over either of Items 22230 to 22234 inclusive on slope inclination.................................................................................................................. 622.70 1,245.40 22235
Temporary storage at the Contractor's holding nursery of the following plants obtained from an existing or a designated location of
any distance to the nursery : -
A
Number per month $
22236 Bamboos, shrubs, ground covers, herbaceous, climbers / small palms and conifers / standard trees or below........................................................................... 12.50 22236
22237 Large palms and conifer / heavy standard trees.............................................................................................................................................................................. 93.40 22237
22238 Semi mature trees or above............................................................................................................................................................................................................. 124.60 22238
Root prune the following plants at the existing location ready for uplift, including all necessary excavation, backfilling, pruning,
removing surplus excavated material from Site, staking, protecting and watering as required for new works by the Specification
and as directed by the Maintenance Surveyor : -
Stem Diameter
50 - 100 - 200 - 350 - 500 - 600 - 700 -
0 - 50mm
100mm 200mm 350mm 500mm 600mm 700mm 800mm
A B C D E F G H
Each $ $ $ $ $ $ $ $
22239 Root prune trees / palms / conifers.................................................................... 18.70 24.90 124.60 373.60 747.20 1,245.40 1,619.00 1,992.60 22239
PART III.E - TREE FELLING AND PRUNING / SURGERY WORKS DBH
95 - 150 - 300 - 450 - 600 -
150mm 300mm 450mm 600mm 750mm
A B C D E
Each $ $ $ $ $
22240 Fell tree including grubbing up roots and stumps and clearing away all arisings, filling in voids
with approved materials, where required, and making good all disturbed ground surfaces
to match existing ..................................................................................................................................................... 1,013.30 1,519.90 2,026.50 3,005.10 3,039.80 22240
A
Per square metre $
22241 Prune climbers and groundcovers................................................................................................................................................................................................... 10.00 22241
22/27
22 LANDSCAPE WORK 22
Item Item
PART III.E - TREE FELLING AND PRUNING / SURGERY WORKS (CONT'D)
A
Each $
22242 Prune for crown cleaning of whip trees / seedling trees / shrubs / bamboos / herbaceous plants................................................................................................ 10.00 22242
22243 Prune for crown cleaning of standard trees / light standard trees / small conifers / palms (Group A, B, C and E)..................................................................... 21.40 22243
22244 Prune for crown cleaning of semi-mature trees / heavy standard trees / large conifers / palms (Group D) / transplanted trees
of overall height n.e. 7 m................................................................................................................................................................................................................ 94.20 22244
22245 Prune for crown cleaning of transplanting trees of overall height between 7 - 18 m.................................................................................................................... 376.60 22245
22246 Prune for crown thinning of whip trees / seedling trees / shrubs / bamboos / herbaceous plants................................................................................................. 21.40 22246
22247 Prune for crown thinning of standard trees / light standard trees / small conifers / palms (Group A, B, C and E)...................................................................... 41.40 22247
22248 Prune for crown thinning of semi-mature trees / heavy standard trees / large conifers / palms (Group D) / transplanted trees
of overall height n.e. 7 m................................................................................................................................................................................................................ 188.30 22248
22249 Prune for crown thinning of transplanted trees of overall height between 7 - 18 m..................................................................................................................... 753.20 22249
Diameter
100 - 200 - 300 - exceeding
200mm 300mm 400mm 400mm
A B C D
Each $ $ $ $
22250 Extra over either of Items 22244 to 22245 and Items 22248 to 22249 inclusive
for limb reduction / removal cut for each limb of diameter..................................................................................................... 62.30 373.60 622.70 1,245.40 22250
PART IV - ESTABLISHMENT WORKS
(Note : The following items 22251 to 22264 inclusive will only be paid for, if ordered by the Maintenance Surveyor
in writing.)
A
Square metre per month $
22251 Basic monthly establishment operations for climbers and groundcovers...................................................................................................................................... 2.50 22251
22252 Basic monthly establishment operations for grass area.................................................................................................................................................................. 3.80 22252
22253 Basic monthly establishment operations for seasonal flowers....................................................................................................................................................... 8.10 22253
22/28
22 LANDSCAPE WORK 22
Item Item
PART IV - ESTABLISHMENT WORKS (CONT'D)
(Note : The following items 22251 to 22264 inclusive will only be paid for, if ordered by the Maintenance Surveyor
in writing)
A
Number per month $
22254 Basic monthly establishment operations for semi-mature trees of above...................................................................................................................................... 9.40 22254
22255 Basic monthly establishment operations for heavy standard trees, large palms and large conifers.............................................................................................. 7.50 22255
22256 Basic monthly establishment operations for standard trees, medium palms and small conifers.................................................................................................. 5.00 22256
22257 Basic monthly establishment operations for light standard trees................................................................................................................................................... 3.10 22257
22258 Basic monthly establishment operations for whip trees / seedling trees / shrubs / bamboos / herbaceous plants........................................................................ 0.40 22258
22259 Basic monthly establishment operations for aquatic plants........................................................................................................................................................... 0.50 22259
22260 Basic monthly establishment operations for indoor semi-mature trees or above.......................................................................................................................... 5.00 22260
22261 Basic monthly establishment operations for indoor heavy standard trees, large palms and large conifers.................................................................................. 5.00 22261
22262 Basic monthly establishment operations for indoor standard trees, medium palms and small conifers....................................................................................... 5.00 22262
22263 Basic monthly establishment operations for indoor potted plants................................................................................................................................................. 1.00 22263
22264 Basic monthly establishment operations for transplanting trees.................................................................................................................................................... 148.60 22264
PART V - SUNDRIES
Plant identification:
A
Number Per Works Order $
22265 Collect, handle and transport plant specimen(s) to AFCD for identification................................................................................................................................ 1,183.10 22265
Each
22266 Submit written report for reporting to relevant Government Authorities...................................................................................................................................... 685.00 22266
22/29
Section 23
GEOTECHNICAL WORKS
23 GEOTECHNICAL WORKS 23
SECTION 23
GEOTECHNICAL WORKS
SPECIAL CONDITIONS
Measurement SC23.01 Inspection scaffolding shall be measured the area of the face to be covered by the
generally scaffolding and no allowance shall be made for surface irregularities or other local
peculiarities.
The rates for inspection scaffolding will only be paid for, if : -
(a) No other works will be executed by the Contractor and it is ordered in writing by
the Maintenance Surveyor; and
(b) The scaffolding will be taken down and clear away after the use for inspection or
uses by other Government departments or other contractor employed by
Government.
Preliminary stripping to existing slopes shall be measured the surface area of the area or
face cleared and no allowance shall be made for surface irregularities or other local
peculiarities.
Rock scaling shall be measured the surface area of the face to be scaled and no allowance
shall be made for surface irregularities or other local peculiarities.
Mesh protection to rock slopes shall be measured the surface area of the face to be
protected and no allowance shall be made for surface irregularities or other local
peculiarities. No deduction shall be made for openings each not exceeding 1.00 m.
All geotechnical works items other than those items specifically included in this Section
shall be measured and paid for at the appropriate rates under applicable Work Sections in
this Schedule.
For avoidance of doubt, all rates in this Section and other appropriate rates under
applicable Works Sections measured in relation to all geotechnical works shall deem to
apply to works executed by the Approved Suppliers of Material and Specialist Contractors
for Public Works : Landslip Preventive/Remedial Works to Slopes/Retaining Walls.
Measurement SC23.02 Mats for erosion control shall be measured net to the area fixed or laid. No deduction shall
of mats for be made for an area not exceeding 1.00 m.
erosion control
Measurement SC23.03 Different types of surface protection shall be measured as the surface area of the face to
of surface be covered and no allowance shall be made for surface irregularities or other local
protection peculiarities. No deduction shall be made for an area not exceeding 1.00 m.
Measurement SC23.04 Measurement of topographic survey shall be the plan area within the boundary as directed by
of topographic the Maintenance Surveyor inclusive of all terrains and irregularities, etc. and measured flat.
survey Measurement shall either be taken at the date of commencement or at the completion or both.
23/1
23 GEOTECHNICAL WORKS 23
SPECIAL CONDITIONS
Measurement SC23.04 The rate for topographic survey will only be paid for if order in writing by the Maintenance
of topographic (Cont'd) Surveyor.
survey
(Cont'd)
Rates generally SC23.05 The rates for all items shall generally include for : -
(a) Conveying, lowering, hoisting, placing in any position at any height on slopes.
(b) All multi-handling between excavation and final position.
(c) All multi-handling between temporary deposition in spoil heaps and removal from
site.
(d) All scaffolding and temporary works.
(e) Submission of survey records before and upon the completion of the geotechnical
works.
PART I - EARTHWORK ON EXISTING SLOPES
Rates for SC23.06 The rates for excavation on existing slopes shall further include for : -
excavation on
existing slopes (a) Mobilization, maintenance and demobilization of excavator, roller, compaction
plant, moving plant and the like.
(b) Allowance for increase in bulk of all materials arising from excavation.
(c) Excavating in any type of ground including earth, clay, sand, gravel, loose
boulders each not exceeding 0.20 m, any hard surface and the like.
(d) Setting out the work and all profiles, rods, etc. and work straight or circular on plan.
(e) Excavating to form buttress.
(f) Cutting down shrubs, under-growths, etc. including trees not exceeding 150 mm
girth, grubbing up roots and clearing away.
(g) Removing old drains, channels, stepped channels, catch pits, etc. and sealing off
connections.
(h) Provision of temporary drainage to the area affected and clearing away after
completion.
(i) Getting out excavated materials by any means necessary and deposit excavated
material in heaps.
(j) Cutting and trimming banks and slopes.
(k) Protecting the exposed surfaces of excavation by any necessary means.
23/2
23 GEOTECHNICAL WORKS 23
SPECIAL CONDITIONS
PART I - EARTHWORK ON EXISTING SLOPES
Rates for SC23.06 (l) Preparation and submission of survey record when ordered by the Maintenance
excavation on (Cont'd) Surveyor.
existing slopes
(Cont'd) (m) Depositing in temporary spoil heaps.
Rates for SC23.07 The rates for earth filling to existing slopes shall further include for : -
earth filling to
existing slopes (a) Additional bulk of filling required to allow for compaction.
(b) Forming and trimming banks and slopes and compaction.
(c) Temporary retaining boards to edges and slopes.
(d) Removing, replacing or making good placed or compacted filling material as
required where filling material subsequently becomes damaged or unsuitable.
(e) Protecting the exposed surfaces of filling by any necessary means.
(f) Apart from probe tests measured separately, all soil tests including in-situ density
tests, maximum dry density tests and etc. as required.
Rates for SC23.08 The rates for soil-cement filling shall further include for : -
soil-cement
filling (a) Preliminary mix trials.
(b) Preliminary trial panels.
(c) Preparation of surface to be filled.
(d) Compacting and finishing surfaces.
(e) Recording and submitting records.
PART II - SLOPE TREATMENTS
Drawings SC23.09 The drawings as referred to in this Schedule and listed in Annex 'A' - Drawing Schedule
and Drawings for Builder's Works of the Schedule can be viewed on the ArchSD internet
website via the pathway referred therein.
Preliminary Stripping
Rates for SC23.10 The rates for preliminary stripping of top soil shall further include for : -
preliminary
stripping of (a) Excavation and disposal of topsoil including loose soil, clearance of vegetations
top soil and undergrowths.
23/3
23 GEOTECHNICAL WORKS 23
SPECIAL CONDITIONS
PART II - SLOPE TREATMENTS
Preliminary Stripping
Rates for SC23.10 (b) Taking up and clearing away vegetation, topsoil, disused drains, stepped channels
preliminary (Cont'd) and the like.
stripping of
top soil (c) Temporary protection of stripped area.
(Cont'd)
(d) Clearing of the slope surface and the area so affected after stripping work by
means of compressed air or other approved means.
(e) Clearing, trimming, scarifying and regulating the surface for slope treatment works.
(f) Taking readings, measurements and observations, recording and submitting
survey records.
(g) Reinstatement of over-stripped area with approved materials.
(h) Removing surplus soil and debris.
Rates for SC23.11 The rates for preliminary stripping of impermeable surfaces shall further include for : -
preliminary
stripping of (a) Excavation and disposal of existing chunam, sprayed concrete and other
impermeable impermeable surfaces in any thickness including vegetations and under-growths.
surfaces
(b) Cutting of reinforcement.
(c) Taking up and clearing away vegetation, topsoil, disused drains, stepped channels
and the like.
(d) Temporary protection of stripped areas.
(e) Clearing of the slope surface and the area so affected after stripping work by
means of compressed air.
(f) Clearing, trimming, scarifying and regulating the surface for slope treatment works.
(g) Taking readings, measurements and observations, recording and submitting survey
records.
(h) Reinstatement of over-stripped area.
(i) Removing surplus soil and debris.
Inspection Scaffolding
Rates for SC23.12 The rates for inspection scaffolding shall further include for : -
inspection
scaffolding (a) Provision, maintenance, inspection, replacement (if required) and subsequent
removal.
23/4
23 GEOTECHNICAL WORKS 23
SPECIAL CONDITIONS
PART II - SLOPE TREATMENTS
Inspection Scaffolding
Rates for SC23.12 (b) Safety ropes, fall-arresting system, harnesses hand and foot holds.
inspection (Cont'd)
scaffolding (c) Platforms, ramps, access, protection fences and barriers.
(Cont'd)
(d) Provision of drawings, calculations in relation to the design of Temporary Works
including endorsement by a Registered Structural Engineer.
(e) Allowance in the works programme for inspection carried out by the
Maintenance Surveyor.
(f) Re-erect or repair the inspection scaffolding to allow the re-inspection, if required.
(g) Obtaining permission from the Maintenance Surveyor for any dismantle works.
(h) Compliance with the requirements of the current Code of Practice for Bamboo
Scaffolding Safety and Code of Practice for Metal Scaffolding Safety.
Probe test
Rates for SC23.13 The rates for GEO probe test shall include for : -
GEO
probe test (a) Carrying out all test and soil samples by the personnel of a Hong Kong
Laboratories Accreditation Scheme (HOKLAS) accredited laboratory using their
own equipment and providing such labour and assistance as may be required.
(b) Collect samples selected by the Maintenance Surveyor.
(c) Report work.
(d) Payment of all charges incurred.
(e) All apparatus and calibration, and associated equipment.
(f) Filling up holes.
(g) In the case of testing the works carried out by the Contractor, re-testing up to the
satisfaction of the Maintenance Surveyor.
Surface Protection
Rates for SC23.14 The rates for chunam shall further include for : -
chunam
(a) Cleaning, trimming and regulating the surface to be covered.
(b) Preliminary trial panels.
(c) Dowels (if required).
23/5
23 GEOTECHNICAL WORKS 23
SPECIAL CONDITIONS
PART II - SLOPE TREATMENTS
Surface Protection
Rates for SC23.14 (d) Weep holes and filter materials.
chunam (Cont'd)
(Cont'd) (e) Finishing and curing.
(f) Fixing anchorage.
(g) Protection of trees, structures, street furniture and the like.
(h) Recording and submitting records.
Rates for SC23.15 The rates for sprayed concrete shall further include for : -
sprayed
concrete (a) Providing, setting up, maintenance and removal of concrete spraying plant,
equipment and all necessary ancillary equipment.
(b) Preliminary mix trials.
(c) Preliminary trial panels.
(d) Test specimens and test panels.
(e) Preparation of surface to be covered.
(f) Formwork.
(g) Weep holes and filter materials.
(h) Forming and including construction joint and expansion joint.
(i) Finishing and curing.
(j) Inspection, sounding, and removal and replacement of sub-standard or hollow
areas.
(k) Coring samples, testing and making good core holes to match existing.
(l) Protection of trees, structures, street furniture and the like.
(m) Recording and submitting records.
Rate for SC23.16 The rate for supply and installation of sign plate shall include for excavation in any material
slope and disposal of surplus material; backfilling and compaction; waterproof membrane or
registration blinding layer; formwork; reinforcement and concrete, supply and protective treatment of
sign plate all metal/alloy or other components of the sign plate; painting; welding; qualification tests
for welders and welding tests.
23/6
23 GEOTECHNICAL WORKS 23
SPECIAL CONDITIONS
PART II - SLOPE TREATMENTS
Rock Scaling, Removal of Boulders, Mesh Protections, and Sealing and
Infilling Rock Joints
Rates for SC23.17 The rates for scaling and trimming of rock slopes shall further include for : -
scaling and
trimming (a) Soil cushions and subsequent removal.
of rock
slopes (b) Washing down.
(c) Scaling and trimming using hand-held tools.
(d) Disposal of scale, debris and boulders using hand-held tools.
(e) Temporary protective measures and subsequent removal.
Rates for SC23.18 The rates for mesh protection to rock slopes shall further include for : -
mesh
protection (a) Preparation of surface.
to rock
slopes (b) Bolts and anchorages.
(c) Lapping, binding and jointing.
(d) Taking down and carting away existing mesh on rock slope.
Rates for SC23.19 The rates for rock or boulder splitting and removal shall further include for : -
rock or
boulder (a) Mobilization, maintenance and demobilization of plant, tools and ancillary
splitting equipment necessary for the works.
and removal
(b) Moving the plant, tools and ancillary equipment at various locations.
(c) Temporary supports for plant, tools and ancillary.
(d) Temporary protective measures and subsequent removal.
(e) Disposal of boulders and debris.
Rates for SC23.20 The rates for sealing and infilling rock joints shall further include for : -
sealing and
infilling (a) Clearing unsuitable infill.
rock joints
(b) Excavating in rock joints to the depth required.
(c) Concrete, cement mortar and/or epoxy mortar.
(d) Formwork.
23/7
23 GEOTECHNICAL WORKS 23
SPECIAL CONDITIONS
PART II - SLOPE TREATMENTS
Rock Scaling, Removal of Boulders, Mesh Protections, and Sealing
and Infilling Rock Joints
Rates for SC23.20 (e) Reinforcement.
sealing and (Cont'd)
infilling (f) Masonry infilling.
rock joints
(Cont'd)
Rates for SC23.21 The rates for concrete buttress shall further include for : -
concrete buttress
(a) Preliminary mix trials.
(b) Slump and other tests as required.
(c) Preparation of surface to be buttressed.
(d) Compacting and finishing surfaces.
(e) Formwork, fair face, if required.
(f) Reinforcement, if required.
(g) PVC outlets connected to relief drainage system.
(h) Recording and submitting records.
Rock Dowels
Rates for SC23.22 The rates for rock dowels shall further include for : -
rock dowels
(a) Providing, setting up, maintenance and removal of sufficient number of
drill rigs and ancillary equipment.
(b) Moving the drill rigs, plant and ancillary equipment between rock dowel
positions.
(c) Drilling in any material.
(d) Water, compressed air and drilling fluids.
(e) Washing out holes.
(f) Grouting.
(g) Protective treatment to stud components.
(h) Recording and submitting records.
23/8
23 GEOTECHNICAL WORKS 23
SPECIAL CONDITIONS
PART II - SLOPE TREATMENTS
Soil Nails
Rates for SC23.23 The rates for soil nails shall further include for : -
soil nails
(a) Providing, setting up, maintenance and removal of sufficient number of drill rigs,
plant and ancillary equipment.
(b) Moving the drill rigs, plant and ancillary equipment between soil nail positions.
(c) Drilling in any material.
(d) Temporary support to drill holes.
(e) Water, compressed air and drilling fluids.
(f) Washing out holes.
(g) Pre-grouting and reaming.
(h) Provision and installation of steel bars.
(i) Grouting.
(j) Protective treatment to steel components.
(k) Couplers and centralizers.
(l) Head assembly, concrete, reinforcement and formwork.
(m) Excavation for soil nail head and disposal of surplus materials.
(n) Supporting device including wire, ties and the like.
(o) Recording and submitting records.
(p) Reinstatement to affected areas.
(q) Protective treatment to steel components, including provision of heat-shrinkable
sleeve, if ordered by the Maintenance Surveyor.
Rates for SC23.24 The rates for soil nails with double corrosion protection shall further include for : -
soil nails
with double (a) Corrugated sheathing as described in the Specification as adopted in the Contract
corrosion with proven record for use in similar projects as approved by the Maintenance
protection Surveyor.
Rates for SC23.25 The rates for pull out tests and performance tests on soil nails shall further include for : -
pull out tests
and performance (a) Setting up, operating, calibrating and maintaining load jacks.
tests on soil
nails
23/9
23 GEOTECHNICAL WORKS 23
SPECIAL CONDITIONS
PART II - SLOPE TREATMENTS
Soil Nails
Rates for SC23.25 (b) Provisions of temporary supports to spread the applied loads.
pull out tests (Cont'd)
and performance (c) Applying and re-applying the test loads and releasing.
tests on soil
nails (Cont'd) (d) Pulling out of soil nail for inspection and grouting the drillhole.
(e) Cutting off any protrusion from the drillhole and grout the remaining part of
drillhole.
(f) Taking readings, measurements and observations of the test and recording
and submitting results of test.
(g) Submission of remedial proposal and replacement of all soil nails failing
the test.
(h) Reinstatement of affected areas.
Drainage and Erosion Control
Rates for relief SC23.26 The rates for relief drains shall further include for : -
drains
(a) Nails, bolts and nuts for fixing and jointing.
(b) Excavation and disposal of material from joints, faults and discontinuities.
(c) Connecting to outlets including junction boxes.
(d) Weep holes.
(e) Trial length.
(f) Sealing up impermeable layers.
(g) Submission of method statement.
(h) P.V.C. flange and end cap.
Rates for SC23.27 The rates for raking drains shall further include for : -
raking drains
(a) Providing, setting up, maintenance and removal of sufficient number of drill rigs
and plant together with all ancillary equipment.
(b) Moving the drill rigs, plant and ancillary equipment between drain hole positions.
(c) Drilling in any material.
(d) Temporary support to drill holes.
(e) Water, compressed air and drilling fluids.
23/10
23 GEOTECHNICAL WORKS 23
SPECIAL CONDITIONS
PART II - SLOPE TREATMENTS
Drainage and Erosion Control
Rates for SC23.27 (f) Taking soil samples and rock cores.
raking drains (Cont'd)
(Cont'd) (g) Recording and submitting records.
(h) Disposal of material.
(i) Temporary sealing for holes.
(j) Pipes, tubes, drain liners, drain screens and the like, including slots and perforations.
(k) Filter sheaths and fabric.
(l) Jointing and socketing.
(m) Bentonite plugs and mortar seals.
(n) Marking.
(o) Reinstatement of affected areas.
Rates for SC23.28 The rates for maintenance of raking drains shall include for : -
maintenance of
raking drains (a) All the equipment and labours, including supply and pumping of water, required for
carrying out the maintenance of raking drains as per paragraphs 16 & 17 of WBTC
No. 10/91 and agreed by the Maintenance Surveyor.
(b) Provision of new removable inner liner as per ArchSD Standard Drawing No.
C2403 if required by the Maintenance Surveyor.
(c) Disposal of the old inner liner in an environmentally acceptable way as agreed by
the Maintenance Surveyor.
Rates for SC23.29 The rates for mats for erosion control shall further include for : -
mats for
erosion control (a) Preparation of surfaces to receive mats including filling irregularities with suitable
materials.
(b) Taking down and carting away existing mats for erosion control on slope.
(c) Pins, anchorages and the like for fixing mats.
(d) Allowance for laps between joints.
Rates for SC23.30 The rates for forming opening to rock mesh and erosion mat on slope shall further
forming opening include for : -
to rock mesh
and erosion mat (a) Setting-out works, wire trimming and making good opening.
on slope
23/11
23 GEOTECHNICAL WORKS 23
SPECIAL CONDITIONS
PART II - SLOPE TREATMENTS
Geotechnical Instrumentation and Sundries
Rates for SC23.31 The rates for tree rings and planter holes in sprayed concrete shall, in addition to the
tree rings and requirements of Special Conditions Clause SC23.15, include for : -
planter holes
(a) Thickened concrete, reinforcement and anchor bars, if required.
(b) Removal of any excessive sprayed concrete inside tree ring and planter hole.
(c) Filling hole with topsoil mix.
Rates for SC23.32 The rates for supply and installation of survey monitoring point shall further include for : -
supply and
installation (a) Installation of stainless steel bolts of minimum 12mm diameter or other similar and
of survey approved with tapered lower end firmly embedded in stone or concrete and
monitoring point protected hemispherical upper end with 1mm diameter drilled hole at apex.
(b) Provision of concrete bedding as directed by the Maintenance Surveyor.
Rates for SC23.33 The rates for monitoring operation at each survey monitoring point shall include for : -
monitoring
operation at each (a) Labour, supervisory staff and equipment necessary for the recording of
survey monitoring measurements to the frequency as required by the Maintenance Surveyor.
point
(b) Preparation and submission of daily records.
Rates for SC23.34 The rates for topographic survey shall include for : -
topographic
survey (a) Carrying out the topographic survey by the qualified personnel of an approved
independent firm using their own equipment and providing such labour and
assistance as may be required.
(b) Preparation and submission of survey plans and reports duly signed by an
authorized surveyor and approved by the Maintenance Surveyor.
(c) Payment of all charges incurred.
Rates for SC23.35 The rate shall include for provision of labour / supervisory staff and diameter for measuring
monitoring of groundwater level.
of piezometer
Rates for SC23.36 The rates for safety fence shall include for : -
safety fence
(a) Provision, erection, maintenance, alteration as required.
(b) Dismantle and clear away to left-in position, as required.
(c) Providing all materials including posts, strut, plates, wire meshes, rock dowel,
anchor bolts, nuts and washers, cable wire, tarpaulin sheets and the like.
23/12
23 GEOTECHNICAL WORKS 23
SPECIAL CONDITIONS
PART II - SLOPE TREATMENTS
Geotechnical Instrumentation and Sundries
Rates for SC23.36 (d) Designs for the temporary works including calculations and drawings endorsed by
safety fence (Cont'd) a Registered Structural Engineer when required.
(Cont'd)
(e) All associated footings including all necessary excavation, disposal, concrete,
reinforcement, base plates as required.
(f) Adequate lightings and warning lights and associated power supply and electrical
works and payment of all charges incurred.
(g) Reinstatement and making good surface disturbed.
Specification for Geotechnical Works
Specification SC23.37 The specification clauses for geotechnical works can be found in : -
clauses
(a) The General Specification for Building.
(b) The General Specification for Civil Engineering Works (Hong Kong
Government).
Geotechnical Works found in other Sections of this Schedule
Turfing and SC23.38 Turfing and grassing to slopes can be found in Section 22 - Landscape Work of this
grassing to slopes Schedule.
Drainage system SC23.39 Drainage system to slopes can be found in Section 13 - Plumbing and Drainage of this
to slopes Schedule.
Concrete works SC23.40 Concrete staircase to slopes and reinforcement to buttress can be found in Section 04 -
to slopes Concrete Work of this Schedule.
Steel railing and SC23.41 Steel railing and staircase to slopes can be found in Section 10 - Steel and Metal Work of
staircase to slopes this Schedule.
Paintwork SC23.42 Paintwork to slopes can be found in Section 15 - Painting of this Schedule.
to slopes
23/13
23 GEOTECHNICAL WORKS 23
Item Item
PART I - EARTHWORK ON EXISTING SLOPES
EARTHWORK ON EXISTING SLOPES
A
Per cubic metre $
23001 Excavate on slopes to reduce levels................................................................................................................................................................................................ 87.80 23001
23002 Load surplus excavated materials and remove from Site............................................................................................................................................................... 124.60 23002
23003 Spread and level or patching up excavated material on slopes in layers n.e. 250 mm including compacting and handling
from spoil heaps.............................................................................................................................................................................................................................. 91.80 23003
23004 Approved soil brought to Site from Contractor's own source and wheeled, spread, levelled, patching up, watered if
necessary and compacted in layers as filling.................................................................................................................................................................................. 154.80 23004
(Note : - This item will only be paid for, if ordered by the Maintenance Surveyor in writing.)
SOIL - CEMENT FILLING
A
Per cubic metre $
23005 Soil-cement filling including compacting and finishing surfaces as required............................................................................................................................... 189.50 23005
REMEDIAL WORK TO BANKS, LANDSLIPS, ETC.
A
Per cubic metre $
23006 Excavate as necessary to trim and cut back eroded, fissured or overhanging banks, slopes and sides of slips at any height
to revised profile, throw or lower earth, boulders, shrubs and other debris arising to bottom of slope and break or cut up
these arisings together with any former material and debris which had been washed down, into a suitable size for handling,
and load and remove from Site and erection, use and clearing away of any ladders, gang planks, shoring, etc., required
(Total volume of material actually loaded and removed measured) ............................................................................................................................................. 147.30 23006
23/14
23 GEOTECHNICAL WORKS 23
Item Item
PART II - SLOPE TREATMENTS
PRELIMINARY STRIPPING
A
Per square metre $
23007 Preliminary stripping of top soil in any depth................................................................................................................................................................................ 32.40 23007
23008 Preliminary stripping of impermeable surfaces in any thickness................................................................................................................................................... 47.10 23008
INSPECTION SCAFFOLDING
A
Per square metre $
23009 Inspection scaffolding..................................................................................................................................................................................................................... 68.10 23009
PROBE TEST
A
Each $
23010 GEO probe test n.e. 3.00 m deep.................................................................................................................................................................................................... 1,486.50 23010
23011 Ditto 3.00 - 6.00 m deep................................................................................................................................................................................................................. 2,494.80 23011
SURFACE PROTECTION
A
Per square metre $
23012 Chunam, 50 mm thick..................................................................................................................................................................................................................... 97.00 23012
23013 Ditto with single layer of 50 x 50 x 2.7 mm wire diameter galvanized welded mesh................................................................................................................... 259.90 23013
23014 Chunam, 75 mm thick..................................................................................................................................................................................................................... 133.40 23014
23015 Ditto with single layer of 50 x 50 x 2.7 mm wire diameter galvanized welded mesh................................................................................................................... 315.30 23015
Grade 20 or 20MPa sprayed concrete with A252 galvanized welded mesh Sprayed concrete with mesh
to BS4483, and with 50 mm diameter weep holes at 1.50 m staggered Single Double
centres in each direction : - layer mesh layer mesh
Thickness (mm) 75 100 125 150 200
A B C D E
Per square metre $ $ $ $ $
23016 Sprayed concrete to slopes...................................................................................................................................... 194.00 239.10 270.30 294.50 438.30 23016
23/15
23 GEOTECHNICAL WORKS 23
Item Item
PART II - SLOPE TREATMENTS (CONT'D)
SURFACE PROTECTION (CONT'D)
Grade 20 or 20MPa sprayed concrete, with single layer of 50 x 50 x 2.7 mm wire
diameter galvanized welded mesh, and with 50 mm diameter weepholes at 1.50 m
staggered centres in each direction : - Sprayed concrete with mesh
Thickness (mm) 50 75 100
A B C
Per square metre $ $ $
23017 Sprayed concrete to slopes.......................................................................................................................................................................... 119.60 151.80 185.70 23017
Grade 20 or 20MPa sprayed concrete, without mesh, and with 50 mm diameter weepholes Sprayed concrete
at 1.50 m staggered centres in each direction : - without mesh
Thickness (mm) 50 75
A B
Per square metre $ $
23018 Sprayed concrete to slopes............................................................................................................................................................................................ 101.90 136.90 23018
A
Per square metre $
23019 Extra over either of Items 23016 to 23018 inclusive for colour pigments in sprayed concrete
in accordance with ASTM C979.................................................................................................................................................................................................... 22.90 23019
Per number
23020 Supply and installation of slope registration sign plate as ArchSD Standard Drawing Nos. 7116_01 to 7116_05..................................................................... 85.70 23020
23021 Take down and clear away ditto..................................................................................................................................................................................................... 25.50 23021
23022 Take down and set aside for re-use ditto........................................................................................................................................................................................ 31.90 23022
23023 Fix only ditto................................................................................................................................................................................................................................... 44.70 23023
23/16
23 GEOTECHNICAL WORKS 23
Item Item
PART II - SLOPE TREATMENTS (CONT'D)
ROCK SCALING, REMOVAL OF BOULDERS, MESH PROTECTION AND SEALING AND
INFILLING ROCK JOINTS
A
Per square metre $
23024 Scaling and trimming of rock slopes including boulders n.e. 0.2 m............................................................................................................................................ 123.50 23024
23025 Mesh protection as ArchSD Standard Drawing No. C2205.......................................................................................................................................................... 157.80 23025
23026 Take down and clear away ditto..................................................................................................................................................................................................... 63.80 23026
Per cubic metre
23027 Sealing rock joints with 1:3 cement mortar.................................................................................................................................................................................... 554.40 23027
23028 Infilling rock joints with no fine concrete...................................................................................................................................................................................... 540.50 23028
23029 Ditto but with Grade 20 or 20MPa concrete.................................................................................................................................................................................. 779.60 23029
23030 Ditto but with soil-cement fill......................................................................................................................................................................................................... 443.50 23030
23031 Ditto but with masonry bedded in cement mortar.......................................................................................................................................................................... 571.70 23031
23032 Ditto but with proprietary epoxy mortar......................................................................................................................................................................................... 1,697.90 23032
23033 Concrete Grade 20 or 20MPa buttress............................................................................................................................................................................................ 1,039.50 23033
23034 Concrete Grade 30 or 30MPa buttress............................................................................................................................................................................................ 1,143.50 23034
23035 Split rocks or boulders exceeding 0.20 m and remove from Site................................................................................................................................................. 459.10 23035
(Note : - The above Item 23032 will only be paid for, if ordered by the Maintenance Surveyor in writing.)
ROCK DOWELS
Supply and install rock dowels as detailed in ArchSD Standard Drawing No. C2202 : - Rock dowels diameter (mm)
25 32 40 50
A B C D
Each $ $ $ $
23036 Rock dowels n.e. 2.00 m long................................................................................................................................................... 749.90 796.50 831.00 940.70 23036
23037 Ditto 2.00 - 3.00 m long............................................................................................................................................................ 1,129.40 1,170.60 1,248.00 1,408.90 23037
23038 Ditto 3.00 - 4.00 m long............................................................................................................................................................ 1,458.50 1,550.20 1,685.60 1,893.60 23038
23039 Ditto 4.00 - 5.00 m long............................................................................................................................................................ 1,746.40 2,054.80 2,269.60 2,385.20 23039
23040 Ditto 5.00 - 6.00 m long............................................................................................................................................................ 2,314.60 2,456.00 2,597.00 3,139.40 23040
23041 Ditto 6.00 - 7.00 m long............................................................................................................................................................ 2,865.50 3,034.30 3,245.60 3,647.60 23041
23042 Add to Item 23041 for each additional 1.00 m or part thereof in length................................................................................. 394.80 414.80 466.60 522.10 23042
23/17
23 GEOTECHNICAL WORKS 23
Item Item
PART II - SLOPE TREATMENTS (CONT'D)
SOIL NAILS
Supply and install soil nails as detailed in ArchSD Standard Drawing No. C2106/1, C2106/2
and C2106/3 : - Soil nails diameter (mm)
25 32 40 50
A B C D
Each $ $ $ $
23043 Soil nail n.e. 3.00 m long.......................................................................................................................................................... 1,536.80 1,759.30 1,866.60 1,948.70 23043
23044 Ditto 3.00 - 4.00 m long............................................................................................................................................................ 2,349.80 2,494.70 2,686.00 2,820.50 23044
23045 Ditto 4.00 - 5.00 m long............................................................................................................................................................ 2,677.10 2,867.50 3,170.20 3,527.40 23045
23046 Ditto 5.00 - 6.00 m long............................................................................................................................................................ 3,019.90 3,240.40 3,585.10 3,925.20 23046
23047 Ditto 6.00 - 7.00 m long............................................................................................................................................................ 3,362.80 3,609.80 3,995.90 4,317.40 23047
23048 Ditto 7.00 - 8.00 m long............................................................................................................................................................ 3,698.70 3,980.60 4,248.10 4,712.40 23048
23049 Ditto 8.00 - 9.00 m long............................................................................................................................................................ 4,034.70 4,385.00 4,821.20 5,114.30 23049
23050 Ditto 9.00 - 10.00 m long.......................................................................................................................................................... 4,490.10 4,718.00 5,237.80 5,784.80 23050
23051 Ditto 10.00 - 11.00 m long........................................................................................................................................................ 4,708.20 5,094.40 5,647.50 6,199.60 23051
23052 Ditto 11.00 - 12.00 m long........................................................................................................................................................ 5,045.90 5,470.70 6,057.30 6,681.00 23052
23053 Ditto 12.00 - 13.00 m long........................................................................................................................................................ 5,501.40 5,951.00 6,602.10 7,276.50 23053
23054 Ditto 13.00 - 14.00 m long........................................................................................................................................................ 5,839.10 6,327.30 7,008.40 7,713.10 23054
23055 Ditto 14.00 - 15.00 m long........................................................................................................................................................ 6,176.80 6,698.40 7,418.10 8,080.40 23055
23056 Add to Item 23055 for each additional 1.00 m or part thereof in length................................................................................. 384.60 422.70 476.40 545.70 23056
23/18
23 GEOTECHNICAL WORKS 23
Item Item
PART II - SLOPE TREATMENTS (CONT'D)
SOIL NAILS (CONT'D)
Supply and install soils nails with double corrosion protection as detailed in ArchSD
Drawing No. R1043/3 and R1043/3-1 and as specified in the Specification Soil nails diameter (mm)
25 32 40
A B C
Each $ $ $
23057 Soil nail n.e. 3.00 m long............................................................................................................................................................................ 2,079.00 2,113.70 2,148.30 23057
23058 Ditto 3.00 - 4.00 m long.............................................................................................................................................................................. 2,772.00 2,806.70 2,841.30 23058
23059 Ditto 4.00 - 5.00 m long.............................................................................................................................................................................. 3,465.00 3,499.70 3,534.30 23059
23060 Ditto 5.00 - 6.00 m long.............................................................................................................................................................................. 4,158.00 4,192.70 4,227.30 23060
23061 Ditto 6.00 - 7.00 m long.............................................................................................................................................................................. 4,851.00 4,885.70 4,920.30 23061
23062 Ditto 7.00 - 8.00 m long.............................................................................................................................................................................. 5,544.00 5,578.70 5,613.30 23062
23063 Ditto 8.00 - 9.00 m long.............................................................................................................................................................................. 6,237.00 6,271.70 6,306.30 23063
23064 Ditto 9.00 - 10.00 m long............................................................................................................................................................................ 6,930.00 6,968.50 6,999.30 23064
23065 Ditto 10.00 - 11.00 m long.......................................................................................................................................................................... 7,623.00 7,657.70 7,692.30 23065
23066 Ditto 11.00 - 12.00 m long.......................................................................................................................................................................... 8,316.00 8,350.70 8,385.30 23066
23067 Ditto 12.00 - 13.00 m long.......................................................................................................................................................................... 9,009.00 9,043.70 9,078.30 23067
23068 Ditto 13.00 - 14.00 m long.......................................................................................................................................................................... 9,702.00 9,736.70 9,771.30 23068
23069 Ditto 14.00 - 15.00 m long.......................................................................................................................................................................... 10,395.00 10,429.70 10,464.30 23069
23070 Add to Item 23069 for each additional 1.00 m or part thereof in length................................................................................................... 693.00 727.70 762.30 23070
A
Each $
23071 Pull-out test of any diameter........................................................................................................................................................................................................... 11,610.00 23071
23072 Performance test of any diameter.................................................................................................................................................................................................... 3,728.30 23072
23/19
23 GEOTECHNICAL WORKS 23
Item Item
PART II - SLOPE TREATMENTS (CONT'D)
DRAINAGE AND EROSION CONTROL
A
Each $
23073 Relief drains 200 mm wide, length n.e. 1.50 m, as detailed in ArchSD
Standard Drawing No. C2404......................................................................................................................................................................................................... 308.40 23073
23074 Ditto for length 1.50 - 3.00 m......................................................................................................................................................................................................... 671.10 23074
23075 Ditto for length 3.00 - 4.50 m......................................................................................................................................................................................................... 1,058.00 23075
Overall length
of each drain
n.e. exceeding
25.00 m 25.00 m
A B
Per linear metre $ $
23076 Raking drains Type 1 upwards at 0 - 45 to the horizontal as detailed in ArchSD
Standard Drawing No. C2403....................................................................................................................................................................................... 153.50 175.00 23076
23077 Ditto but Type 2............................................................................................................................................................................................................ 187.50 245.00 23077
23078 Ditto but Type 3............................................................................................................................................................................................................ 241.50 297.40 23078
A
Per item $
23079 Mobilization for maintenance of raking drains, including flushing with a clean air/water jet with a suitable
pressure as agreed by the Maintenance Surveyor, in accordance with the requirements as paragraphs
16 & 17 of ETWB TC(W) No. 10/91............................................................................................................................................................................................. 6,540.30 23079
Per number
23080 Extra over Item 23079 for completion, to the satisfaction of the Maintenance Surveyor, maintenance of raking
drains, including flushing with a clean air/water jet with a suitable pressure in accordance with the
requirements at paragraphs 16 & 17 of ETWB TC(W) No. 10/91............................................................................................................................................... 401.90 23080
23/20
23 GEOTECHNICAL WORKS 23
Item Item
PART II - SLOPE TREATMENTS (CONT'D)
DRAINAGE AND EROSION CONTROL (CONT'D)
Proprietary mats for erosion prevention/control on level or slope complying with the following specification including Supply
all necessary fixing accessories and all in accordance with manufacturer's instructions : - and
fix
A
Per square metre $
Material Dense three-dimensional filament structure open matting fused totally where
filaments cross and added with carbon black and UV stabilizers to secure
resistance to weathering and UV radiation
Colour Black
Thickness 20 mm
Density 25 kg/m3
Free volume 95%
Area holding capacity 19.7 x 106 mm3/m2
(The quantity of soil
retained in the mat)
Polymer type Polyamide 6
Polymer density 1140 kg/m3
Tensile strength :
- longitudinal direction 2.0 kN/m tested to DIN 53857
- transverse direction 1.2 kN/m tested to EN 10319
- of the joints 0.6 kN/m tested to EN 10319
Chemical resistance Resistant to all chemicals in concentrations normally contained in the earth and
surface water
Temperature resistance -30 to +100
Inflammability Classification B2 tested to DIN 4102
Smoke formation Low and suitable for used in tunnels
Toxicity None and suitable for use in potable water reservoirs
Rodent damage No nutritive value to support burrowing animals and rodents
Environmental protection Inert and not harmful to the environment
23081 Proprietary mat for erosion prevention........................................................................................................................................................................................... 64.10 23081
23082 Take down and clear away ditto..................................................................................................................................................................................................... 19.10 23082
Material Four layers of dense webs of polyethylene monofilaments thermally welded
together
Colour Black or green
Weight 450 gm/m2
Thickness 18 mm
Filament diameter 0.75 mm
Porosity 90 %
Tensile strength 3.2 kN/m tested to BS 6906 : Part 1 : 1987
Elongation 360 % tested to BS 6906 : Part 1 : 1987
Water flow rate 1000 L/sec/m2 tested to ASTM D4491-89
23083 Proprietary mat for erosion control................................................................................................................................................................................................. 55.40 23083
23084 Take down and clear away ditto..................................................................................................................................................................................................... 17.90 23084
23/21
23 GEOTECHNICAL WORKS 23
Item Item
PART II - SLOPE TREATMENTS (CONT'D)
DRAINAGE AND EROSION CONTROL (CONT'D)
Proprietary drainage filter system on level or slope complying with the following specification including all necessary fixing Supply
accessories and all in accordance with manufacturer's instructions : - and
fix
A
Per square metre $
Material A light and flexible geocomposite matting composed of a drainage core of
Composite drainage unit
looped polypropylene filaments and nonwoven filter fabric on both sides
thermally bonded together over the entire area and where filaments cross
Colour Black
Thickness 9 mm
Weight 540 g/m2
Discharge 2.00 l/s/m at 20 kPa tested to EN ISO 12958 under
0.80 l/s/m at 50 kPa hydraulic gradient 1:1
Water permeability mean value 110 mm/s tested to EN ISO 11058 at VIH50
mean value 180 m tested to EN ISO 12956 at opening size O90
Weight mean value 90 g/m2 tested to EN 965
Filter fabric alone
Thickness mean value 0.4 mm tested to EN 964-1
Tensile strength mean value 5 kN/m tested to EN 10319 at machine direction
Tensile strength mean value 6 kN/m tested to EN 10319 at cross machine direction
Elongation at break mean value 33 % tested to EN 10319 at machine direction
Resistance to static mean value 0.8 kN/m tested to EN 12236
puncture
Dynamic perforation mean value 48 mm tested to EN 918
resistance
23085 Proprietary drainage filter mat suitable to protect vertical surfaces of shallow underground building structures against seepage
and for horizontal drainage layer for lightweight green roof constructions and flower planters ................................................................................................. 72.80 23085
Material A geocomposite vertical drainage blanket composed of a plastic cusplates
inner core (cuspation on both sides) over wrapped with a heat-bonded
non-woven geotextile filter fabric bonded on one side only
Mean peak strength 9 kN/m tested to AS 3706.2 at machine direction
8 kN/m tested to AS 3706.2 at cross machine direction
Geotextile wrap
Trap tear 320 N tested to AS 3706.3 and ASTM D4533
Grab tensile 730 N tested to AS 2001.2.3
CBR burst strength 1800 N tested to AS 3706.4 and BS 6906:Part 4
Drop cone 1150 mm tested to AS 3706.5
G rating 1000 Nmm0.5 tested to AS 3706.2
G classification Mod robust tested to AS 3706.2
Pore size < 120 m tested to AS 3706.7 at EOS O95
< 75 m tested to AS 3706.7 at O95 when dry
Permeability 275 l/m2/s tested to AS 3706.9 at flow rate of 10 cm head
Core profile Raised cuspation on both sides (square shaped)
HDPE plastic core
Weight 900 g/m2
Colour Black
Fungus resistance Excellent
Crush strength 250 kPa
Core thickness 18 mm
23086 Proprietary drainage blanket suitable to reduce hydrostatic pressure behind structural walls ..................................................................................................... 108.10 23086
23/22
23 GEOTECHNICAL WORKS 23
Item Item
PART II - SLOPE TREATMENTS (CONT'D)
DRAINAGE AND EROSION CONTROL (CONT'D)
Proprietary drainage filter system on level or slope complying with the following specification including all necessary fixing Supply
accessories and all in accordance with manufacturer's instructions : - (Cont'd) and
fix
A
Per square metre $
Material A composite drainage filter structure composed of a three dimensional, high
Filter fabric Drainage structure
impact and creep resistance polymeric drainage core panel factory bonded to
an anti-clogging filter fabric and adhered with a polymeric backing
Thickness 10.2 mm
Inplane flow rate 261 l/min./m width at 400 kPa tested to ASTMD 4716
Compressive strength 790 kN/m2 tested to ASTMD 1621
Material High flow non-woven needle-punched fabric
Apparent opening size 0.085 mm tested to BS 6906 Part 1, Part 2 and Part 4
Puncture resistance 2250 N tested to BS 6906 Part 1, Part 2 and Part 4
Tensile strength 13.5 kN/m tested to BS 6906 Part 1, Part 2 and Part 4
23087 Proprietary drainage core panel suitable for vertical application behind foundation walls, basement cavity walls and tunnel walls......................................... 129.60 23087
Material A composite drainage filter structure composed of a three dimensional, high
Drainage structure
impact and creep resistance polymeric drainage core panel factory bonded to
an anti-clogging filter fabric
Thickness 10.2 mm
Inplane flow rate 302 l/min./m width at 400 kPa tested to ASTMD 4716
Compressive strength 862 kN/m2 tested to ASTMD 1621
Material Woven monofilament anti-clogging fabric
Apparent opening size 0.30 mm tested to BS 6906 Part 1, Part 2 and Part 4
% opening 10 %
Filter fabric
Puncture resistance 2700 N tested to BS 6906 Part 1, Part 2 and Part 4
Tensile strength 41 kN/m tested to BS 6906 Part 1, Part 2 and Part 4
at machine direction
30 kN/m tested to BS 6906 Part 1, Part 2 and Part 4
at cross machine direction
23088 Proprietary drainage core panel suitable for vertical and horizontal surfaces of planter boxes and roof gardens........................................................................ 149.00 23088
23/23
23 GEOTECHNICAL WORKS 23
Item Item
PART II - SLOPE TREATMENTS (CONT'D)
DRAINAGE AND EROSION CONTROL (CONT'D)
A
Per cubic metre $
23089 Coarse granular filter (Filter B)....................................................................................................................................................................................................... 270.30 23089
23090 Fine granular filter (Filter A).......................................................................................................................................................................................................... 262.20 23090
Each
23091 Filter drainage pipe as detailed in ArchSD Standard Drawing No. C2302, 50 mm diameter, length n.e. 3.00 m....................................................................... 90.10 23091
23092 Ditto, for length 3.00 - 6.00 m........................................................................................................................................................................................................ 149.00 23092
Diameter of opening (mm)
n.e. 500 1000 1500
500 - 1000 - 1500 - 2000
A B C D
Each $ $ $ $
23093 Form opening to rock mesh or erosion control mat on slope................................................................................................... 32.70 68.80 104.80 140.90 23093
GEOTECHNICAL INSTRUMENTATION AND SUNDRIES
A
Per month $
23094 Monitoring operation at each survey monitoring point.................................................................................................................................................................. 225.20 23094
Each
23095 Supply and installation of survey monitoring point....................................................................................................................................................................... 370.80 23095
23096 Dismantle and remove survey monitoring point, reinstatement of disturbed surfaces and making good.................................................................................... 10.40 23096
23097 Monitoring operation at each standpipe piezometer...................................................................................................................................................................... 13.20 23097
23/24
23 GEOTECHNICAL WORKS 23
Item Item
PART II - SLOPE TREATMENTS (CONT'D)
GEOTECHNICAL INSTRUMENTATION AND SUNDRIES (CONT'D)
A
Each $
23098 Construct tree rings in sprayed concrete as detailed in ArchSD Standard Drawing No. C2104,
inner ring diameter n.e. 800 mm..................................................................................................................................................................................................... 253.00 23098
23099 Ditto 800 - 1,200 mm...................................................................................................................................................................................................................... 338.90 23099
23100 Ditto 1,200 - 1,800 mm................................................................................................................................................................................................................... 508.00 23100
23101 Ditto 1,800 - 2,400 mm................................................................................................................................................................................................................... 637.60 23101
23102 Ditto 2,400 - 3,000 mm................................................................................................................................................................................................................... 844.80 23102
23103 150 mm Diameter perforated pipe planter holes not exceeding 600 mm long with top soil mix in chunam, 45.10 23103
sprayed concrete or masonry facing slope......................................................................................................................................................................................
23104 300 mm Ditto.................................................................................................................................................................................................................................. 91.40 23104
Per square metre
23105 Carry out topographic survey.......................................................................................................................................................................................................... 3.50 23105
(Note : - This item will only be paid for, if ordered by the Maintenance Surveyor in writing.)
SAFETY FENCE Erect,
maintain, Erect,
take maintain
down and and left in
clear position
away
A B
Per linear metre $ $
23106 Safety fence "Type A" as detailed in Drawing Nos. C2501/1B and C2501/2B.......................................................................................................... 1,774.10 1,462.20 23106
23107 Safety fence "Type A with Highway barrier" as detailed in Drawing Nos. C2501/1B, C2501/2B and H2112......................................................... 2,016.60 1,853.80 23107
23108 Safety fence "Type B" as detailed in Drawing Nos. C2502/1C and C2502/2C.......................................................................................................... 2,113.70 1,975.10 23108
23/25
Section 24
PRESERVATION AND PROTECTION OF PRESERVED TREES
24 PRESERVATION AND PROTECTION OF PRESERVED TREES 24
SECTION 24
PRESERVATION AND PROTECTION OF PRESERVED TREES
SPECIAL CONDITIONS
Particular SC24.01 This Section shall be read and used in conjunction with the Particular Specification for
Specification Preservation and Protection of Existing Trees including Old and Valuable Trees and
relevant Conditions of Contract adopted in the Contract.
Particular SC24.02 The items in this Section are applicable to existing trees which are to be preserved and
Preamble protected including Old and Valuable Trees (hereinafter referred to as OVT) from
the register at the website : http://www.lcsd.gov.hk/LEISURE/LP/gc/tree
PRESERVATION AND PROTECTION OF PRESERVED TREES
INCLUDING OLD AND VALUABLE TREES
Measurement SC24.03 The measurement for the items for the preservation and protection measures for Old and
of preservation Valuable Trees shall be the duration in which preservation and protection measures for
and protection of OVT are stated in the Works Order and provided in accordance with the requirements of
preserved trees the Contract. One item shall be measured for each OVT.
including Old and
Valuable Trees
SC24.04 The measurement for the item for the preservation and protection measures for preserved
trees other than Old and Valuable Trees shall be the duration in which preservation and
protection measures for preserved trees other than OVT as stated in the Works Order
and provided in accordance with the requirements of the Contract. One item shall be
measured for each tree.
Rates for SC24.05 The rates for preservation and protection measures for Old and Valuable Trees shall
preservation include for : -
and protection
of preserved (a) All works, materials and services for preservation and protection for the OVT in
trees including accordance with the Contract.
Old and Valuable
Trees (b) Provision, installation, securing, maintenance, reinstatement and removal of
identification, labelling or marking system for OVT.
(c) Provision, installation, securing, maintenance, reinstatement and removal of
temporary protective fencing/armouring/mulching for OVT.
(d) Provision, installation, securing, maintenance, reinstatement and removal of
physical support measures to protect the OVT from instability.
(e) Provision, installation, securing, maintenance and reinstatement of measures to
protect the OVT from reduction in ground level, including construction of retaining
wall, precautionary measures during excavation and root cutting, and measures to
maintain balanced moisture content after change in ground level.
24/1
24 PRESERVATION AND PROTECTION OF PRESERVED TREES 24
SPECIAL CONDITIONS
PRESERVATION AND PROTECTION OF PRESERVED TREES
INCLUDING OLD AND VALUABLE TREES
Rates for SC24.05 (f) Provision, installation, securing, maintenance and reinstatement of measures to
preservation (Cont'd) protect the OVT from rise in ground level, including construction of dry well and
and protection soil aeration system.
of preserved
trees including (g) Measures to protect the OVT from excavation, including submission of
Old and Valuable photographic records, precautionary measures during excavation, tunnelling of
Trees services and root cutting, and measures to maintain balanced moisture content
(Cont'd) after excavation.
(h) Measures to protect the OVT from drilling, including precautionary measures
during drilling and root cutting, and measures to maintain balanced moisture
content after drilling.
(i) Measures to control pest and disease for the OVT, including precautionary
measures to prevent pest and disease attack and control measures to eradicate
pest and disease from the infected trees.
(j) Pruning of the OVT, including pre-pruning preparation, pruning operation,
post-pruning treatment and reinstatement of affected areas.
(k) Precautionary measures for the OVT as stated in the Contract.
Rates for SC24.06 The rates for preservation and protection measures for preserved trees other than Old and
preservation Valuable Trees shall include for : -
and protection
of preserved (a) All works, materials and services for preservation and protection to preserved
trees other than trees other than OVT in accordance with the Contract.
Old and Valuable
Trees (b) Provision, installation, securing, maintenance, reinstatement and removal of
identification labelling or marking systems for preserved trees other than OVT.
(c) Provision, installation, securing, maintenance, reinstatement and removal of temporary
protective fencing/armouring/mulching for preserved trees other than OVT.
(d) Provision, installation, securing, maintenance, reinstatement and removal of
physical support measures to protect the preserved trees other than OVT from
instability.
(e) Provision, installation, securing, maintenance and reinstatement of measures to
protect the preserved trees other than OVT from reduction in ground level,
including construction of retaining wall, precautionary measures during excavation
and root cutting, and measures to maintain balanced moisture content after change
in ground level.
(f) Provision, installation, securing, maintenance and reinstatement of measures to
protect the preserved trees other than OVT from rise in ground level, including
construction of dry well and soil aeration system.
24/2
24 PRESERVATION AND PROTECTION OF PRESERVED TREES 24
SPECIAL CONDITIONS
PRESERVATION AND PROTECTION OF PRESERVED TREES
INCLUDING OLD AND VALUABLE TREES
Rates for SC24.06 (g) Measures to protect the preserved trees other than OVT from excavation,
preservation (Cont'd) including submission of photographic records, precautionary measures during
and protection excavation, tunnelling of services and root cutting, and measures to maintain
of preserved balanced moisture content after excavation.
trees other than
Old and Valuable (h) Measures to protect the preserved trees other than OVT from drilling, including
Trees precautionary measures during drilling and root cutting, and measures to maintain
(Cont'd) balanced moisture content after drilling.
(i) Measures to control pest and disease for the preserved trees other than OVT,
including precautionary measures to prevent pest and disease attack and control
measures to eradicate pest and disease from infected trees.
(j) Pruning of the preserved trees other than OVT, including pre-pruning preparation,
pruning operation, post-pruning treatment and reinstatement of affected areas.
(k) Precautionary measures for the preserved trees other than OVT as stated in the
Contract.
TREE SURVEY
Measurement SC24.07 The item for tree survey of each existing tree including Old and Valuable Tree shall be
of tree survey measured for each tree to be surveyed as stated in the Works Order and required in the
Contract.
Measurement SC24.08 The item for reports on photographic record of each preserved tree including Old and
of reports Valuable Tree shall be measured for each tree to be preserved as stated in the Works
Order and required in the Contract.
Rates for SC24.09 The rates for tree survey of each existing tree including Old and Valuable Tree shall
tree survey include for : -
(a) All works, materials and services for undertaking tree survey of existing trees
including OVT in accordance with the Works Order.
(b) Preparing, amending and submitting to the Maintenance Surveyor the updated
survey record of the trees.
(c) Provision and installation of identification labelling or marking systems for all
existing trees including OVT earmarked to be felled under the Works Order.
24/3
24 PRESERVATION AND PROTECTION OF PRESERVED TREES 24
SPECIAL CONDITIONS
TREE SURVEY
Rates for SC24.10 The rates for reports on photographic record of each preserved tree including Old and
reports Valuable Tree shall include for : -
(a) All works, materials and services for preparation, submission, amendments and
updating of reports on photographic record of preserved trees including OVT in
accordance with the Works Order.
(b) Taking updated photographs of preserved trees including OVT.
INDEPENDENT TREE SPECIALIST
Measurement SC24.11 The measurement for the items for independent tree specialist (hereinafter referred to as
of independent ITS) shall be the duration in which the services of an ITS is stated in the Works Order and
tree specialist provided in accordance with the Contract.
Rates for SC24.12 The rates for ITS shall include for : -
independent
tree specialist (a) Payment for wages for the ITS.
(b) Provision of services required from the ITS as stipulated in the Contract including
conducting tree surveys, site surveys and soil tests, submitting reports and
providing advice.
(c) All works, materials and services for employment of the ITS and provision of the
services required from the ITS in accordance with the Contract including payment
of all fees and charges, provision of facilities and attendance on the ITS.
AFTERCARE TO OLD AND VALUABLE TREES
Measurement SC24.13 The measurement for the items for aftercare to Old and Valuable Treesshall be made to
of aftercare to the duration in which all requirements for providing aftercare to OVT as stated in the
Old and Valuable Works Order and provided in the Contract are complied with. One item shall be measured
Trees for each OVT.
Rates for SC24.14 The rates for aftercare to each Old and Valuable Tree shall include for : -
aftercare to each
Old and Valuable (a) All works, materials and services for providing aftercare to OVT in accordance
Tree with the Contract.
(b) Tree maintenance work, work of repair to damage or health deterioration, or
precautionary or mitigation measures against damage.
(c) Removal of all debris and surplus materials off the Site.
(d) Reinstatement of the affected areas.
24/4
24 PRESERVATION AND PROTECTION OF PRESERVED TREES 24
Item Item
PRESERVATION AND PROTECTION OF PRESERVED TREES
A
Per month $
24001 Preservation and protection measures for each Old and Valuable Tree........................................................................................................................................ 3,038.20 24001
24002 Preservation and protection measures for each existing tree other than Old and Valuable Tree.................................................................................................. 182.30 24002
TREE SURVEY
A
Per number $
24003 Tree survey of each existing tree including Old and Valuable Tree.............................................................................................................................................. 158.00 24003
24004 Reports on photographic record of each preserved tree including Old and Valuable Tree.......................................................................................................... 121.50 24004
INDEPENDENT TREE SPECIALIST
A
Per number-month $
24005 Independent tree specialist.............................................................................................................................................................................................................. 20,100.00 24005
AFTERCARE TO OLD AND VALUABLE TREES
A
Per month $
24006 Aftercare to each Old and Valuable Tree....................................................................................................................................................................................... 2,187.50 24006
24/5
Section 25
CONTROL TREATMENT ON PESTS, TERMITES AND
RED IMPORTED FIRE ANTS
25 CONTROL TREATMENT ON PESTS, TERMITES AND RED IMPORTED FIRE ANTS 25
SECTION 25
CONTROL TREATMENT ON PESTS, TERMITES AND RED IMPORTED FIRE ANTS
SPECIAL CONDITIONS
PART I - CONTROL TREATMENT ON PESTS AND TERMITES
Measurement of SC25.01 Only the infested areas by pests and termites as directed by the Maintenance Surveyor
pest and termite shall be measured.
control
Measurement of SC25.02 The items for provision of termite treatment to Old and Valuable Tree (OVT) shall be
termite treatment measured based on each OVT where termite infestation around the OVT is confirmed by
to Old and the Maintenance Surveyor.
Valuable Trees
Rates for pest SC25.03 The rates for pest and termite control shall include for : -
and termite
control (a) The application of an appropriate pesticide or insecticide approved by the
Agriculture, Fisheries and Conservation Department (AFCD) or any control
treatment methods approved by the Maintenance Surveyor.
(b) The employment of a pest control specialist approved by the Maintenance
Surveyor.
(c) Applying the pesticide or insecticide in strict accordance with the manufacturer's
instructions.
Rates for SC25.04 The rates for termite treatment in mounds and timber shall further include for : -
termite
treatment in (a) Carrying out the investigation for the presence of termites.
mounds and
timber (b) Preparing and drilling holes around termite mounds for the injection of the
approved pesticide or insecticide.
(c) Treatment services on the termite mounds.
(d) Collection services of specimens of termites.
(e) Eradication and removal of all termites and their queens.
(f) Carrying out periodic inspection to ensure that the termite treatment is effective.
(g) Provision of guarantee.
25/1
25 CONTROL TREATMENT ON PESTS, TERMITES AND RED IMPORTED FIRE ANTS 25
SPECIAL CONDITIONS
PART I - CONTROL TREATMENT ON PESTS AND TERMITES
Rates for SC25.05 The rates for termite treatment to Old and Valuable Trees (OVT) shall further include for : -
termite treatment
to Old and (a) Carrying out the investigation for the presence of termites including the extent of
Valuable Trees affected soil around the OVT.
(b) Preparing and drilling holes in ground for installation of timber interceptor as
in-ground bait station.
(c) Installing of termite mud-tubes at infested area of above-ground bait station.
(d) Working at any inclination of slopes if the OVT are on slopes.
(e) Eradication and removal of all termites and their queens.
(f) Carrying out treatment services.
(g) Carrying out periodic inspection to ensure that the termite treatment is effective.
(h) Provision of guarantee.
PART II - TREATMENT SERVICES ON RED IMPORTED FIRE ANTS
Particular SC25.06 This Section shall be read and used in conjunction with the Particular Specification for
Specification Treatment Services on Red Imported Fire Ants and relevant Conditions of Contract
adopted for the Contract.
Particular SC25.07 A pest control specialist in controlling Red Imported Fire Ants (RIFA) from the list
Preamble provided by AFCD shall be employed to provide treatment services for the RIFA
including their mounds.
The updated list of the pesticides for RIFA treatment available from AFCD shall be
referred when proposing pesticides for approval.
PROTECTION OF EXISTING PLANTING
Measurement of SC25.08 The items for maintain and protect all existing planting in the controlling area shall be
treatment services measured where treatment services are required to be carried out in planted area.
on Red Imported
Fire Ants
Rates for SC25.09 The rates for maintain and protect all existing planting in the controlling area shall
treatment services include for the following whenever maintenance or protection is not possible : -
on Red Imported
Fire Ants (a) Report to the Maintenance Surveyor with alternative proposal.
(b) Resume the original condition including re-planting to the satisfaction of the
Maintenance Surveyor.
25/2
25 CONTROL TREATMENT ON PESTS, TERMITES AND RED IMPORTED FIRE ANTS 25
SPECIAL CONDITIONS
PART II - TREATMENT SERVICES ON RED IMPORTED FIRE ANTS
COLLECTION SERVICES OF THE SUSPECTED RED IMPORTED FIRE ANTS
Measurement SC25.10 The items for mark, cordon off and isolate possible infested zone around single suspected
of collection RIFA mound shall be measured once for a single suspect of RIFA in one location. If there
services of are multiple suspected RIFA mounds in the same location, the add to Item shall be
the suspected measured for each additional mound.
Red Imported
Fire Ants
SC25.11 The items for collect specimen of suspected RIFA shall be measured once for each
Works Order as directed by the Maintenance Surveyor.
SC25.12 The items for add to Item for each additional specimen collection shall only be measured
as directed by the Maintenance Surveyor.
SC25.13 The item for reporting to relevant Government Authorities shall be measured once only
for the Works Order.
Rates for SC25.14 The rates for mark, cordon off and isolate possible infested zone and add to Item for
collection each multiple suspected RIFA mound shall include for : -
services of the
suspected Red (a) The provision of cordon line.
Imported Fire
Ants (b) Clear warning signs in both English and Chinese about the presence of suspected
RIFA and the relevant pest control situation.
SC25.15 The rates for collect specimen of suspected RIFA and add to for each additional
specimen collection shall include for : -
(a) Storage of specimen in an approved container and in 70% alcohol.
(b) Collection, handling and transporting all specimens of suspected RIFA to the
Plant and Pesticides Regulatory Division of AFCD.
SC25.16 The rates for reporting to the relevant Government Authorities shall include for : -
(a) Completion and submission of necessary information in the appropriate forms to
AFCD, Development Bureau and other relevant Government Authorities.
CONTROL SERVICES OF THE CONFIRMED RED IMPORTED FIRE ANTS
Measurement of SC25.17 The item for submit a proposal of controlling RIFA shall be measured once only for the
control services of the Works Order of treatment services on RIFA.
confirmed Red
Imported Fire Ants
25/3
25 CONTROL TREATMENT ON PESTS, TERMITES AND RED IMPORTED FIRE ANTS 25
SPECIAL CONDITIONS
PART II - TREATMENT SERVICES ON RED IMPORTED FIRE ANTS
CONTROL SERVICES OF THE CONFIRMED RED IMPORTED FIRE ANTS
Measurement of SC25.18 The item for clear and remove mulch from site shall be measured for the infested area of
control services of the the site as directed by the Maintenance Surveyor.
confirmed Red
Imported Fire Ants
(Cont'd) SC25.19 The items for pest control over infested area shall be measured for the infested area of
the site as directed by the Maintenance Surveyor.
SC25.20 The item for pest control to confirmed RIFA mounds shall be measured where RIFA
mounds are confirmed and as directed by the Maintenance Surveyor.
SC25.21 The item for submit written report after each controlling service shall be measured for
each controlling service completed.
Rates for SC25.22 The rates for submit a proposal of controlling RIFA shall include for : -
control services
of the confirmed (a) Submission of proposal for controlling RIFA including but not limited to pest control
Red Imported methodology to individual mound treatment and/or over large infested area.
Fire Ants
(b) Submission of working programme including pest control schedule and surveillance
programme schedule.
(c) Submission of layout plan showing the location of pest control to be provided.
(d) Submission of details of the pesticides to be applied including Material Safety Data
Sheet, application procedures with precautionary measures and ecological information.
SC25.23 The rates for clear and remove mulch from site shall include for : -
(a) Treating mulch with approved pest control methodology before removal.
(b) Making good disturbed surfaces to match existing.
SC25.24 The rates for pest control over large infested area shall include for : -
(a) The application of a pest control methodology approved by the Maintenance Surveyor.
SC25.25 The rates for pest control up to five confirmed RIFA mounds shall include for : -
(a) The application of a pest control methodology approved by the Maintenance
Surveyor.
(b) The application up to the first 5 number of confirmed RIFA mounds identified for
the Works Order.
25/4
25 CONTROL TREATMENT ON PESTS, TERMITES AND RED IMPORTED FIRE ANTS 25
SPECIAL CONDITIONS
PART II - TREATMENT SERVICES ON RED IMPORTED FIRE ANTS
CONTROL SERVICES OF THE CONFIRMED RED IMPORTED FIRE ANTS
Rates for SC25.26 The rates for submit written report after each controlling service shall include for : -
control services
of the confirmed (a) Reporting the effectiveness of each individual pest control.
Red Imported
Fire Ants (b) Reporting any new findings of RIFA mound.
(Cont'd)
SURVEILLANCE MONITORING OF THE CONFIRMED RED
IMPORTED FIRE ANTS
Measurement of SC25.27 The item for carry out surveillance visit shall be measured for the monitoring the
surveillance effectiveness of RIFA eradication as directed by the Maintenance Surveyor.
monitoring of the
confirmed Red
Imported Fire Ants SC25.28 The item for submit written report after each surveillance visit shall be measured for
each surveillance visit completed.
Rates for SC25.29 The rates for carry out surveillance visit up to five confirmed RIFA mound shall include
surveillance for : -
monitoring of
the confirmed (a) Carry out the visit to monitor the effectiveness of RIFA eradication up to the
Red Imported first 5 number of confirmed RIFA mounds.
Fire Ants
SC25.30 The rates for submit written report after each surveillance visit shall include for : -
(a) Reporting the effectiveness of the RIFA eradication.
(b) Reporting any new findings of RIFA mound.
25/5
25 CONTROL TREATMENT ON PESTS, TERMITES AND RED IMPORTED FIRE ANTS 25
Item Item
PART I - CONTROL TREATMENT ON PESTS AND TERMITES
PEST CONTROL
A
Per square metre $
25001 Provide pest/mosquito control over infested area for which the Contractor is not liable under his contractual obligations
and when ordered by the Maintenance Surveyor........................................................................................................................................................................... 5.80 25001
TERMITE CONTROL
A
Per item $
25002 Provide termite treatment in mounds and to timber skirting, floor boards, wall linings, door frames and architraves, cupboards
and wardrobes and all other surfaces within an infested premise of enclosed and covered internal floor area n.e. 100 m ....................................................... 3,465.00 25002
25003 Add to Item 25002 for each additional 10 m or part thereof in area ........................................................................................................................................... 577.50 25003
25004 Provide termite treatment to each Old and Valuable Tree including applying approved termite colony toxicant
to the infested area around the OVT, applying chemical bait to in-ground bait station in soil and above ground
bait station around infested area, all in accordance with the manufacturer's instructions............................................................................................................ 9,240.00 25004
Per month
25005 Provide regular inspection and monitoring services of the termite bait stations to each Old and Valuable Tree including
applying approved chemical bait as required and preparation and submission of all necessary information and reports........................................................... 1,386.00 25005
PART II - TREATMENT SERVICES ON RED IMPORTED FIRE ANTS
PROTECTION OF EXISTING PLANTING
A
Per item $
25006 Maintain and protect all existing planting in the controlling area................................................................................................................................................. 5,486.30 25006
COLLECTION SERVICES OF THE SUSPECTED RED IMPORTED FIRE ANTS
A
Each $
25007 Mark, cordon off and isolate possible infested zone around single suspected Red Imported Fire Ant mound............................................................................ 1,559.30 25007
25008 Add to Item 25007 for each multiple suspected Red Imported Fire Ant mound........................................................................................................................... 357.40 25008
25009 Collect specimen of suspected Red Imported Fire Ant.................................................................................................................................................................. 1,212.80 25009
25010 Add to Item 25009 for each additional specimen collection.......................................................................................................................................................... 505.60 25010
Per item
25011 Reporting to relevant Government Authorities.............................................................................................................................................................................. 1,443.80 25011
25/6
25 CONTROL TREATMENT ON PESTS, TERMITES AND RED IMPORTED FIRE ANTS 25
Item Item
PART II - TREATMENT SERVICES ON RED IMPORTED FIRE ANTS (CONT'D)
CONTROL SERVICES OF THE CONFIRMED RED IMPORTED FIRE ANTS
A
Per item $
25012 Submit a proposal of controlling Red Imported Fire Ant............................................................................................................................................................... 2,310.00 25012
Per square metre
25013 Clear and remove mulch from Site................................................................................................................................................................................................. 11.60 25013
25014 Pest control over infested area........................................................................................................................................................................................................ 2.30 25014
Per item
25015 Pest control up to five confirmed Red Imported Fire Ant mounds................................................................................................................................................ 1,155.00 25015
Each
25016 Add to Item 25015 for each subsequent confirmed Red Imported Fire Ant mound..................................................................................................................... 231.00 25016
Per item
25017 Submit written report after each controlling service...................................................................................................................................................................... 1,155.00 25017
SURVEILLANCE MONITORING OF THE CONFIRMED RED IMPORTED FIRE ANTS
A
Per item $
25018 Carry out surveillance visit up to five confirmed Red Imported Fire Ant mounds....................................................................................................................... 1,155.00 25018
Each
25019 Add to Item 25018 for each subsequent confirmed Red Imported Fire Ant mound..................................................................................................................... 346.50 25019
Per item
25020 Submit written report after each surveillance visit......................................................................................................................................................................... 1,155.00 25020
25/7
Section 61
SITE SAFETY
61 SITE SAFETY 61
SECTION 61
SITE SAFETY
SPECIAL CONDITIONS
Particular SC61.01 This Section shall be read and used in conjunction with the Particular Specification for Site
Specification Safety and relevant Conditions of Contract adopted in the Contract.
Particular SC61.02 Where no pre-priced rates are provided in this Section, the rates will be provided under
Preamble individual Term Contract.
For any rates to be provided and for pre-priced rates appearing in this Section, they shall
be deemed to allow for the value of work in connection with meeting all statutory and
contractual obligations in the upkeeping of safety and health in the execution of the Works
and any other related obligations, liabilities, risks and profit. In the event that the rates have
been insufficient or where there are any aspects where the methods of measurement
provided hereunder do not measure any item or exclude the measurement of any item or
part thereof, the difference in value shall be deemed to have been included in the Contract
Percentages allowed for other Sections in the Schedule of Rates.
SAFETY PLAN
Complete Draft Safety Plan
Measurement of SC61.03 The item for complete draft Safety Plan shall be measured and paid for when the draft
complete draft Safety Plan has been submitted and the content is in order when confirmed by the
Safety Plan Maintenance Surveyor in writing.
Rates for SC61.04 The rates for complete draft Safety Plan shall include for : -
complete draft
Safety Plan (a) Prepare and complete the draft Safety Plan incorporating the details required by
the Contract.
(b) Submit the draft Safety Plan to the Maintenance Surveyor.
(c) Attend ad hoc meetings with the Maintenance Surveyor to discuss the draft
Safety Plan.
Complete Safety Plan
Measurement of SC61.05 The item for complete Safety Plan shall be measured and paid for when the Maintenance
complete Safety Surveyor is satisfied and confirmed in writing that the Safety Plan has been completed and
Plan it meets all requirements of the Contract at the time of its completion and copies
distributed.
61/1
61 SITE SAFETY 61
SPECIAL CONDITIONS
Rates for SC61.06 The rates for complete Safety Plan shall include for : -
complete Safety
Plan (a) Develop and complete the Safety Plan based on the draft Safety Plan and taking
into account comments given by the Maintenance Surveyor or any other parties.
(b) Distribute the Safety Plan to all relevant parties.
Updating of Safety Plan
Measurement of SC61.07 The item for updating of Safety Plan shall be measured for the period of time
updating of commencing from the completion of the Safety Plan until the date of substantial completion
Safety Plan of the last Works Order or an earlier or later date notified by the Maintenance Surveyor.
No measurement shall be made for the updating of Safety Plan for any period of time in
which the Contractor fails to discharge any of its contractual obligations in respect of
reviewing, revising updating the Safety Plan.
Rates for SC61.08 The rates for updating of Safety Plan shall include for : -
updating of
Safety Plan (a) Review, update and revise the Safety Plan taking also into account of comments
made on the Safety Plan by the Maintenance Surveyor and any other parties.
(b) Update risk assessment for the work scheduled at least for the next two months.
(c) Review and establish safety and health provisions, safe working procedures
and method statements.
(d) Update emergency and rescue procedures.
(e) Distribute the revisions of the Safety Plan to all relevant parties.
PROVIDE SAFETY OFFICER
Provide Safety Officer
Measurement SC61.09 The item for provide Safety Officer shall be measured for the period commencing from
of provide the date of appointment of the Safety Officer as approved by the Maintenance Surveyor
Safety Officer or the date on which the Safety Officer commences his duty on the Site whichever is the
later.
No measurement shall be made for any Safety Officer employed by the Contractor over
and above the minimum number of Safety Officers required under the Particular
Specification for Site Safety.
No measurement shall be made after the date of substantial completion of the last Works
Order or an earlier or later date notified by the Maintenance Surveyor.
No measurement shall be made for any period of time in which the Safety Officer fails to
discharge any of his duties.
61/2
61 SITE SAFETY 61
SPECIAL CONDITIONS
Rates for provide SC61.10 The rates for provide Safety Officer shall include for : -
Safety Officer
(a) Submission to the Maintenance Surveyor for approval of the qualifications and
experience of the proposed Safety Officer.
(b) Provision of sufficient number of Safety Officers in accordance with the Particular
Specification for Site Safety and supporting staff to the Safety Officer.
(c) Performance of all duties of the Safety Officer.
(d) Maintenance of the safety diary.
SITE SAFETY MANAGEMENT COMMITTEE
Attend Site Safety Management Committee
Measurement SC61.11 The measurement shall commence from the date of the first meeting of the Site Safety
of attend Management Committee until the substantial completion of the last Works Order or an
Site Safety earlier or later date notified by the Maintenance Surveyor.
Management
Committee No measurement shall be made for any month in which the Contractor fails to hold or
attend any such Committee meeting in accordance with the Contract or fails to deal with
any of the matters associated with such Committee in a satisfactory manner.
Rates for SC61.12 The rates for attend Site Safety Management Committee shall include for : -
attend
Site Safety (a) Attend Site Safety Management Committee meetings and complete the agenda of
Management the meetings.
Committee
(b) Arrange inspection of the Site by members of the Site Safety Management
Committee before meetings.
(c) Provide necessary assistance for the proper functioning of the Site Safety
Management Committee.
(d) Submission of a monthly safety report for consideration at the meeting.
SITE SAFETY COMMITTEE
Attend Site Safety Committee
Measurement SC61.13 The measurement shall commence from the date of the first meeting of the Site Safety
of attend Committee until the substantial completion of the last Works Order or an earlier or later
Site Safety date notified by the Maintenance Surveyor.
Committee
No measurement shall be made for any month in which the Contractor fails to hold or
attend any such Committee meeting in accordance with the Contract or fails to deal with
any of the matters associated with such Committee in a satisfactory manner.
61/3
61 SITE SAFETY 61
SPECIAL CONDITIONS
Rates for SC61.14 The rates for attend Site Safety Committee shall include for : -
attend
Site Safety (a) Establish the Site Safety Committee.
Committee
(b) Arrange and give adequate notice to relevant parties of the Site Safety Committee
meeting to be held for that month.
(c) Attend at Site Safety Committee meetings.
(d) Completion and distribution of minutes of meetings.
ARRANGE AND ATTEND WEEKLY SAFETY WALK
Arrange and Attend Weekly Safety Walk
Measurement of SC61.15 Only those safety walks conducted in accordance with Particular Specification for Site
arrange and Safety during the period between the date for the commencement of the Works and the
attend weekly date of substantial completion of the last Works Order or an earlier or later date notified
safety walk by the Maintenance Surveyor shall be measured.
No measurement shall be made for the weekly safety walk when any one of the following
events occurs during that week : -
(i) Any Suspension Notice has been issued by the Labour Department pursuant to
the Occupational Safety and Health Ordinance in respect of any activities on the
Site until the notice has been revoked or the operation of that notice is
suspended.
(ii) The Maintenance Surveyor has suspended the progress of the Works or any part
thereof due to any reason caused by any default on the part of the Contractor in
failing to ensure safety and health.
(iii) The Maintenance Surveyor has given written notification to the Contractor
requiring the Contractor to rectify any failure in the proper and full implementation
of the Safety Plan and the Contractor has failed to rectify within a reasonable
time.
Rates for SC61.16 The rates for arrange and attend weekly safety walk shall include for : -
arrange and
attend weekly (a) Arranging and giving adequate notice to relevant parties of the safety walk.
safety walk
(b) Using a comprehensive checklist during the walk to identify and record, and
subsequently rectifying any deficiencies noted in the safety provisions.
(c) Preparing reports on safety walks and safety inspections conducted.
(d) Implementing and upkeeping all measures stipulated in the Safety Plan and
maintaining the effectiveness of all such provisions for the duration of the
Contract.
61/4
61 SITE SAFETY 61
SPECIAL CONDITIONS
Rates for SC61.16 (e) Safety inspections including, but not be limited to : -
arrange and (Cont'd)
attend weekly (i) scaffolding;
safety walk (ii) temporary electrical supply; and
(Cont'd) (iii) site cleanliness;
(f) Implementing the decisions and recommendations made by the Site Safety
Management Committee on matters of safety and health.
PROVIDE SAFETY TRAINING
Provide Trade Specific Advanced Safety Training to Skilled Workers
Measurement SC61.17 The item for provide trade specific advanced safety training to skilled workers shall be
of provide paid on a per worker basis subject to the production of a Silver Card issued by the
trade specific Construction Industry Training Authority as evidence in accordance with Particular
advanced safety Specification for Site Safety. Payment shall only be made for attending the second day of
training to the two-day trade specific advanced safety training course. No payment will be made if
skilled workers the second day of the course is attended : -
(a) before the skilled worker starts works on Site; or
(b) after the skilled worker has left the Site.
Rates for SC61.18 The rates for provide trade specific advanced safety training to skilled workers shall
provide trade include for : -
specific advanced
safety training to (a) Arranging skilled workers to attend the Silver Card training course organised by
skilled workers the Construction Industry Training Authority or any other recognised courses
notified by the Maintenance Surveyor.
(b) Payment of the token allowance to skilled workers.
(c) Preparation of training programme and records, and submission of certified
monthly statements to the Maintenance Surveyor.
(d) Administration in connection with (a), (b) and (c) above.
Provide Site Specific Safety Induction Training
Measurement SC61.19 The item for provide site specific safety induction training shall be measured on a per
of provide person per talk basis. Refresher talks required by the Contract shall also be measured.
site specific
safety induction Adjustment to payment or no payment will be made to the item for provide site specific
training safety induction training if the Maintenance Surveyor is dissatisfied with the frequency,
arrangements, numbers certified, relevance or quality of such training and the Contractor
cannot provide any justification acceptable to the Maintenance Surveyor.
61/5
61 SITE SAFETY 61
SPECIAL CONDITIONS
Rates for SC61.20 The rates for provide site specific safety induction training shall include for : -
provide site
specific safety (a) Site specific safety induction talks conducted in accordance with Particular
induction training Specification for Site Safety.
(b) The necessary facilities, trainers and demonstration equipment for compliance
with (a) above.
(c) Preparation of the training programme and records, submission of certified
monthly statements to the Maintenance Surveyor.
(d) Administration in connection with (a), (b) and (c) above.
Provide Tool Box Talks
Measurement of SC61.21 The item for provide tool box talks shall be measured on a per worker per talk basis on
provide tool a frequency of one talk per worker every two weeks in accordance with Particular
box talks Specification for Site Safety. Adjustment to payment or no payment to be made to the
item for provide tool box talks if the Maintenance Surveyor is dissatisfied with the
frequency, arrangements, numbers certified, relevance or quality of such talks and the
Contractor cannot provide any justification acceptable to the Maintenance Surveyor.
Rates for SC61.22 The rates for provide tool box talks shall include for : -
provide tool
box talks (a) Tool box talks conducted in accordance with Particular Specification for Site
Safety.
(b) The necessary training of Safety Supervisors, foremen or gangers to conduct
tool box talks.
(c) Basing such talks on training kits published by the Hong Kong Construction
Association Ltd. or other training kits of comparable standard approved by the
Maintenance Surveyor.
(d) Preparation of training programme and records, and submission of certified
monthly statements to the Maintenance Surveyor.
(e) Administration in connection with (a), (b), (c) and (d) above.
61/6
61 SITE SAFETY 61
Item Item
SCHEDULE FOR PAY FOR SAFETY SCHEME
(Note : - No pre-priced rates are provided in Items 61001 to 61007 inclusive in this Section. The rates of these items will be
provided under individual Term Contract.
The rates set out in this Section will only be paid for, if ordered by the Maintenance Surveyor in writing and
demonstrated compliance with the Particular Specification for Site Safety)
A
Per item $
61001 Complete draft Safety Plan............................................................................................................................................................................................................. - 61001
61002 Complete Safety Plan...................................................................................................................................................................................................................... - 61002
Per month
61003 Updating of Safety Plan.................................................................................................................................................................................................................. - 61003
Per number-month
61004 Provide Safety Officer..................................................................................................................................................................................................................... - 61004
Per month
61005 Attend Site Safety Management Committee.................................................................................................................................................................................. - 61005
61006 Attend Site Safety Committee......................................................................................................................................................................................................... - 61006
Per number-week
61007 Arrange and attend weekly safety walk.......................................................................................................................................................................................... - 61007
Per number
61008 Provide trade specific advanced safety training to skilled workers............................................................................................................................................... 650.00 61008
61009 Provide site specific induction training.......................................................................................................................................................................................... 100.00 61009
61010 Provide tool box talks...................................................................................................................................................................................................................... 30.00 61010
61/7
Section 62
SITE CLEANLINESS AND TIDINESS
62 SITE CLEANLINESS AND TIDINESS 62
SECTION 62
SITE CLEANLINESS AND TIDINESS
SPECIAL CONDITIONS
Particular SC62.01 This Section shall be read and used in conjunction with the Particular Specification for
Specification Daily Cleaning and Weekly Tidying and relevant Conditions of Contract adopted for the
Contract.
Particular SC62.02 Pre-priced rates appearing in this Section shall be deemed to allow for the value of work
Preamble in connection with meeting all statutory and contractual obligations in the upkeeping of site
cleanliness and tidiness in the execution of the Works and any other related obligations,
liabilities, risks and profit. In the event that the rates have been insufficient or where there
are any aspects where the methods of measurement provided hereunder do not measure
any item or exclude the measurement of any item or part thereof, the difference in value
shall be deemed to have been included in the Contract Percentages allowed for other
Sections in the Schedule of Rates.
Measurement SC62.03 The measurement of Daily Cleaning shall be made after cleaning and tidying up work of
of "Daily the Site of a Works Order for a Cleaning Day is carried out satisfactorily in accordance
Cleaning" with Clause 1(c) Daily Cleaning of Particular Specification for Daily Cleaning and
Weekly Tidying. The measurement of this item for a Cleaning Day shall be the area of the
Public Cleaning Areas in a Works Order for that Cleaning Day. The daily cleaning for the
areas of the Site other than the Public Cleaning Areas shall be deemed to be included in
the rates of other items of work for such Works Order and shall not be measured for
payment.
The extent of the Public Cleaning Areas required for cleaning shall be determined by the
Maintenance Surveyor's Representative for each Works Order.
The Contractor shall not be entitled to any payment for the item for Daily Cleaning for a
Works Order on a Cleaning Day if the performance of the Contractor on cleanliness and
tidiness for any part of the Site including areas other than the Public Cleaning Areas of
such Works Order for that Cleaning Day is not carried out to the satisfaction of the
Maintenance Surveyor's Representative. For the avoidance of doubt, the measurement for
Daily Cleaning" for each Works Order on a Cleaning Day shall be either in full or none.
The Contractor shall not be entitled to any payment for the item for Daily Cleaning for
more than one day for the cleaning and tidying up work carried out by the Contractor in
one Cleaning Day.
Rates for SC62.04 The item for Daily Cleaning shall include for : -
"Daily
Cleaning" (a) Daily cleaning on each Cleaning Day.
(b) Development of inspection checklist for the daily cleaning, and its revision.
62/1
62 SITE CLEANLINESS AND TIDINESS 62
SPECIAL CONDITIONS
Rates for SC62.04 (c) Assignment of person at supervisory level or higher responsible for the daily
"Daily (Cont'd) inspection and checking after the daily cleaning has been carried out on the Site.
Cleaning"
(Cont'd) (d) Completion of the inspection checklist and preparation of records and photographs
for checking by the Maintenance Surveyor's Representative.
(e) Inspection of the Site before any work commences to clear any rubbish and debris
that may be littered by the public.
Measurement SC62.05 The measurement of Weekly Tidying shall be made after the overall cleaning and tidying
of "Weekly up work of the Site of a Works Order for a Cleaning Week Day is carried out satisfactorily
Tidying" in accordance with Clause 1(d) Weekly Tidying of Particular Specification for Daily
Cleaning and Weekly Tidying. The measurement of this item for a satisfactory completed
Cleaning Week Day shall be the area of the Public Cleaning Areas in a Works Order for
that Cleaning Week Day. The weekly tidying for the areas of the Site other than the Public
Cleaning Areas shall be deemed to be included in the rates of other items of work for
such Works Order and shall not be measured for payment.
The extent of the Public Cleaning Areas required for weekly tidying is identical to those
defined for daily cleaning given in Special Conditions Clause SC62.03 herein.
The Contractor shall not be entitled to any payment for the item for Weekly Tidying for
a Works Order on a Cleaning Week Day if the Contractor fails to rectify the identified
defects pursuant to Special Conditions Clause SC62.06(e) herein to the satisfaction of the
Maintenance Surveyor's Representative before the end of the day (which is not a General
Holiday) following the Cleaning Week Day. For the avoidance of doubt, the measurement
for Weekly Tidying for each Works Order on a Cleaning Week Day shall be either in
full or none.
The Contractor shall not be entitled to any payment for the item for Weekly Tidying for
more than one day for the cleaning and tidying up work and/or defects rectification carried
out by the Contractor in one Cleaning Week Day.
Rates for SC62.06 The item for Weekly Tidying shall include for : -
"Weekly
Tidying" (a) Weekly tidying of the Site on the Cleaning Week Day.
(b) Development of inspection checklist for weekly tidying, and its revision.
(c) Assignment of person at supervisory level or higher responsible for the inspection
and checking after the weekly tidying has been carried out on the Site.
(d) Completion of the inspection checklist and preparation of records and photographs
for checking by the Maintenance Surveyor's Representative.
(e) Rectification of defects identified by the assigned person as referred to in
sub-clause (c) above and/or the Maintenance Surveyor's Representative.
(f) Inspection of the Site before any work commences to clear any rubbish and
debris that may be littered by the public.
62/2
62 SITE CLEANLINESS AND TIDINESS 62
Item Item
SCHEDULE FOR PAY FOR SITE CLEANLINESS AND TIDINESS
(Note : - The rates set out in this Section will only be paid for, if ordered by the Maintenance Surveyor in writing and demonstrated A
compliance with the Particular Specification for Site Cleanliness and Tidiness by the Contractor for these items.) $
Per m- day
62001 Daily cleaning.................................................................................................................................................................................................................................. 1.00 62001
62002 Weekly tidying................................................................................................................................................................................................................................ 1.80 62002
62/3
Section 63
TRIP TICKET SYSTEM
63 TRIP TICKET SYSTEM 63
SECTION 63
TRIP TICKET SYSTEM
SPECIAL CONDITIONS
Particular SC63.01 This Section shall be read and used in conjunction with the Particular Specification for
Specification Trip Ticket System and relevant Conditions of Contract adopted for the Contract.
Particular SC63.02 Pre-priced rates appearing in this Section shall be deemed to allow for the value of
Preamble work in connection with meeting all statutory and contractual obligations in ensuring
proper disposal of construction and demolition materials generated from the Site to
designated disposal ground under the Contract or other disposal grounds approved or
as directed by the Maintenance Surveyor, and any other related obligations, liabilities,
risks and profit. In the event that the rates are insufficient or where there are any
aspects where the methods provided hereunder do not measure any item or exclude
the measurement of any item or part thereof, the difference in value shall be deemed to
have been included in the Contract Percentages allowed for other Sections in the
Contract.
Measurement of SC63.03 The item for complete site management plan for trip ticket system shall be measured
complete site once for the whole Contract when the Maintenance Surveyor approves the site
management plan management plan.
for trip ticket
system
Measurement of SC63.04 The measurement of the implementation of site management plan for trip ticket
implementation of system shall be the period of time commencing from the date of approval by the
site management plan Maintenance Surveyor of the site management plan until all construction and
for trip ticket demolition materials have been removed from the Site, or an earlier or later date
system notified by the Maintenance Surveyor.
No measurement shall be made for the implementation of site management plan for
trip ticket system for any month during which there is any incident of improper
disposal or major improper disposal as defined in Clauses 15 and 16 of the Particular
Specification for Trip Ticket System, or late submission of the records as required in
Clause 10 of the Particular Specification for Trip Ticket System, or there is no
disposal of construction and demolition materials off the Site during the month.
Rates for SC63.05 The item for complete site management plan for trip ticket system shall include for : -
complete site
management plan (a) Prepare the site management plan for trip ticket system to the satisfaction of
for trip ticket the Maintenance Surveyor.
system
(b) Distribute or inform all relevant parties details of the site management plan for
trip ticket system.
(c) Inform truck drivers engaged in the disposal of construction and demolition
materials the requirements under the trip ticket system.
63/1
63 TRIP TICKET SYSTEM 63
SPECIAL CONDITIONS
Rates for SC63.06 The item for the implementation of site management plan for trip ticket systemshall
implementation of include for : -
site management
plan for trip ticket (a) Review, update and revise the site management plan for trip ticket system
system taking into account the comments made by the Maintenance Surveyor or any
other parties.
(b) Assign staff and provide / operate / maintain / remove video recording system
and other necessary facilities/equipment for overseeing and implementation of
site management plan for trip ticket system.
(c) Implement measures to ensure that trucks carrying construction and
demolition materials from the Site proceed to the disposal grounds designated
in the Contract or directed or approved by the Maintenance Surveyor to his
satisfaction.
(d) Devise and implement appropriate measures to ensure that the sorted
recyclable materials, which are sorted on the Site for the purpose of recycling
such materials, are delivered to a proper recycling outlet for processing.
(e) Compile, submit and maintain disposal records.
(f) Investigate and report on incidents of improper disposal and non-compliance
with the trip ticket system.
(g) Monitor performance of trip ticket system and implement improvement
measures.
(h) Implement additional measures to control disposal of construction and
demolition materials to alternative disposal ground which the Maintenance
Surveyor has approved.
(i) Distribute revisions of the site management plan for trip ticket system to all
relevant parties including the truck drivers engaged in delivery of construction
and demolition materials for disposal.
(j) Other requirements for implementation of the trip ticket system as stipulated
in the Particular Specification clauses for Trip Ticket System.
63/2
63 TRIP TICKET SYSTEM 63
Item Item
SCHEDULE FOR PAY FOR TRIP TICKET SYSTEM A
$
Per item
63001 Complete Site Management Plan.................................................................................................................................................................................................... 12,000.00 63001
Per month
63002 Implementation of Site Management Plan..................................................................................................................................................................................... 1,000.00 63002
63/3
Section 64
MONITORING PAYMENT OF WAGES
64 MONITORING PAYMENT OF WAGES 64
SECTION 64
MONITORING PAYMENT OF WAGES
SPECIAL CONDITIONS
Particular SC64.01 This Section shall be read and used in conjunction with the Particular Specification for
Specification Monitoring of Wage Payment to Site Personnel and relevant Conditions of Contract
adopted for the Contract.
Measurement for SC64.02 The item for operating monitoring system for payment of wages shall be measured
operating commencing from the date of approval by the Maintenance Surveyor of completion of
monitoring system establishment of monitoring system for payment of wages and the item for providing
for payment of Contractors Labour Officershall commence from the date the Contractors Labour
wages Officer provided by the Contractor is approved by the Maintenance Surveyor and
reports duty on Site. These items shall not be measured:
(a) Where the Works are not divided into Sections, between
(i) the end of the prescribed time or extended time for completion of the
last Works Order except Establishment Works and Aftercare to Old
and Valuable Trees due to extension of time which has been granted
by the Maintenance Surveyor to the Contractor under sub-clauses
(1)(b)(iii), (iv), (vi), (vii) and (viii) of GCC Clause 53; and
(ii) the date of completion of the last Works Order except Establishment
Works and Aftercare to Old and Valuable Trees certified by the
Maintenance Surveyor in accordance with GCC Clause 56.
For the purpose of calculating the extended time for completion of the Works
due to extension of time granted by the Maintenance Surveyor under
sub-clauses (1)(b)(iii), (iv), (vi), (vii) and (viii) of GCC Clause 53, the periods
of extended time for completion granted under sub-clauses (1)(b)(iii), (iv),
(vi), (vii) and (viii) of GCC Clause 53 shall be summed and added to the end
of the prescribed time for completion of the last Works Order.
(b) Where the Works are divided into Sections, between
(i) the end of the prescribed time or extended time for completion of the
Section of the Works (excluding the Sections for Establishment Works
and Aftercare for Old and Valuable Trees) due to extension of time
which has been granted by the Maintenance Surveyor to the Contractor
under sub-clauses (1)(b)(iii), (iv), (vi), (vii) and (viii) of GCC Clause 53,
which happens to be the latest in time (for the purpose of calculating the
extended time for completion of each Section of the Works due to
extension of time granted by the Maintenance Surveyor under
sub-clauses (1)(b)(iii), (iv), (vi), (vii) and (viii) of GCC Clause 53, the
periods of extended time for completion granted under sub-clauses
(1)(b)(iii), (iv), (vi), (vii) and (viii) of GCC Clause 53 for that Section of
the Works shall be summed and added to the end of the prescribed time
for completion of that Section of the Works); and
64/1
64 MONITORING PAYMENT OF WAGES 64
SPECIAL CONDITIONS
Measurement for SC64.02 (ii) the date of completion of whichever Section of the Works (excluding
operating (Cont'd) the Sections for Establishment Works and Aftercare for Old and
monitoring system Valuable Trees) certified by the Maintenance Surveyor in
for payment of accordance with GCC Clause 56 which happens to be the latest in
wages time.
(Cont'd)
(c) After the expiry of the Maintenance Period (or where there is more than one
such Maintenance Period, after the expiry of the last Maintenance Period
other than the Maintenance Periods for Establishment Works and Aftercare
for Old and Valuable Trees) where services are required as a consequence
of the default of the Contractor.
Measurement and SC64.03 No measurement and no payment shall be made for the item operating monitoring
payment for system for payment of wages for the period where there is any incident of
operating non-compliance with respect to the submission of documents and records in
monitoring system accordance with Particular Specification Section X and payment for the item shall
for payment of therefore be measured on a pro rata basis.
wages
Rate for SC64.04 The item for establishing monitoring system for payment of wages is given as a
establishing pre-priced rate and shall include for : -
monitoring system
for payment of (a) Preparation of the monitoring system for payment of wages to the satisfaction
wages of the Maintenance Surveyor.
(b) Setting-up the monitoring system for payment of wages and any modifications
thereof.
(c) Provision for collection and maintenance records of payment of wages to Site
Personnel.
(d) Opening of accounts in designated bank for relevant parties as required in
Particular Specification Clauses X.5 (1) to (2).
(e) Nomination of a Contractors Labour Officer as required in Particular
Specification Clause Y.1.
(f) Setting up the attendance recording system for accurate attendance records
of Site Personnel and any modifications thereof.
(g) Issuing identification cards to Site Personnel and self-employed workers.
(h) Insurance for the self-employed workers.
(i) Establishing a hotline in the Maintenance Surveyors site office to receive
enquiries from workers and Site Personnel on employment matters.
(j) Advising Site Personnel of the monitoring system and the procedures for
reporting wages arrears.
64/2
64 MONITORING PAYMENT OF WAGES 64
SPECIAL CONDITIONS
Rate for SC64.05 The item for operating monitoring system for payment of wages is given as a
operating pre-priced rate. In the event that the rate is insufficient or where there are any aspects
monitoring where the methods provided hereunder do not measure any item or exclude the
system for measurement of any item or part thereof, the difference in value shall be deemed to
payment of have been included in the Contract Percentages allowed for other Sections in the
wages Schedule of Rates. In addition, the rate shall also be deemed to include for :
(a) Operating and maintaining the attendance recording system to obtain accurate
attendance records of Site Personnel.
(b) Controlling the issue of identification cards to Site Personnel and
self-employed workers.
(c) Reviewing, updating and revising the monitoring system for payment of wages
taking into account the comments made by the Maintenance Surveyor or any
other parties.
(d) Implementing measures to ensure that payments of wages to Site Personnel
are consistent with the records of the attendance recording system.
(e) Compiling, submitting and maintaining records of payment of wages and other
monetary benefits to Site Personnel.
(f) Observing all statutory and contractual obligations in ensuring proper
payment of wages and other monetary benefits to Site Personnel, and any
other related obligations, liabilities, risks and profit.
(g) Providing all necessary assistance to the Labour Relations Officer in the
discharge of his duties, functions and responsibilities.
(h) Maintaining a hotline in the Maintenance Surveyors site office.
(i) Maintaining insurance for the self-employed workers.
(j) Providing access and assistance to visitors as required under Particular
Specification Clause Y.3 including the necessary insurance coverage.
Rate for SC64.06 The item for Providing Contractors Labour Officer is given as a pre-priced rate. In
providing the event that the rate is insufficient or where there are any aspects where the methods
Contractor's provided hereunder do not measure any item or exclude the measurement of any item
Labour or part thereof, the difference in value shall be deemed to have been included in the
Officer Contract Percentages allowed for other Sections in the Schedule of Rates. In
addition, the rate shall include the costs and expenses of providing the Contractors
Labour Officer and supporting staff inclusive and without limitation to the following :
(a) Basic salary.
(b) Gratuity.
(c) Overtime payment.
(d) Sundry allowance.
(e) Housing allowance.
(f) Travel allowance.
(g) Leave allowance.
64/3
64 MONITORING PAYMENT OF WAGES 64
SPECIAL CONDITIONS
Rate for SC64.06 (h) Education allowance.
providing (Cont'd) (i) Medical allowance.
Contractor's (j) Dental allowance.
Labour (k) Bonus.
Officer (l) Contribution to a registered mandatory provident fund scheme
(Cont'd) (m) All necessary levies, e.g. Construction Industry Council.
(n) Insurances.
(o) Fringe benefits.
64/4
64 MONITORING PAYMENT OF WAGES 64
Item Item
MONITORING PAYMENT OF WAGES
A
Per item $
64001 Establishing monitoring system for payment of wages.................................................................................................................................................................. 10,000.00 64001
Per month
64002 Operating monitoring system for payment of wages...................................................................................................................................................................... 15,000.00 64002
64003 Providing Contractor's Labour Officer........................................................................................................................................................................................... 12,000.00 64003
64/5
Section 65
SUB-CONTRACTOR MANAGEMENT PLAN
65 SUB-CONTRACTOR MANAGEMENT PLAN 65
SECTION 65
SUB-CONTRACTOR MANAGEMENT PLAN
SPECIAL CONDITIONS
Particular SC65.01 This Section shall be read and used in conjunction with the Particular Specification
Specification for Management of Sub-contractors and relevant Conditions of Contract
adopted for the Contract.
Particular SC65.02 The pre-priced rates appearing in the items under this Section shall be deemed to
Preamble have allowed for the value of work in connection with meeting all contractual
obligations regarding the Sub-contractor Management Plan (SMP) in the execution of
the Works and any other related obligations, liabilities, risks and profit. In the event
that the rates have been insufficient or where there are any aspects where the methods
provided hereunder do not measure any item or exclude the measurement of any item
or part thereof, the difference in value shall be deemed to have been included in the
Contract Percentages allowed for other Sections in the Schedule of Rates.
Measurement SC65.03 Measurement
of complete
Sub-contractor (a) The item for "complete Sub-contractor Management Plan" shall be measured
Management and paid for when the SMP has been submitted, the content is in order and
Plan the Maintenance Surveyor is satisfied and confirmed in writing that it has been
completed and it meets all requirements of the contract at the time of its completion.
(b) The item for "quarterly updating of Sub-contractor Management Plan" shall be
measured and paid for when the quarterly updated SMP has been submitted, the
content is in order and the Maintenance Surveyor is satisfied and confirmed in
writing that the SMP has been completed and meets all the requirements of the
Contract at the time of its completion. The declaration referred to in the Particular
Specification for Management of Sub-contractors Clause X.3(2) shall be
considered as quarterly updating of the SMP. No measurement shall be made for
Contractors interim notification of major changes of sub-contractor management.
Rate for SC65.04 The item for "complete Sub-contractor Management Plan" shall include for : -
complete
Sub-contractor (a) Develop and complete the SMP incorporating the details required by the Contract.
Management
Plan (b) Submit the required copies of the SMP to the Maintenance Surveyor.
Rate for SC65.05 The item for "quarterly updating of Sub-contractor Management Plan" include for : -
quarterly
updating of (a) Reviewing, updating and revising SMP taking into account the changes
Sub-contractor in the Contractor's sub-contracting arrangement during the period
Management and/or comments made by the Maintenance Surveyor.
Plan
(b) Submit the required copies of the quarterly updated SMP to the
Maintenance Surveyor.
65/1
65 SUB-CONTRACTOR MANAGEMENT PLAN 65
Item Item
SUB-CONTRACTOR MANAGEMENT PLAN
A
Per item $
65001 Complete Sub-contractor Management Plan.................................................................................................................................................................................. 15,000.00 65001
Each
65002 Quarterly updating of Sub-contractor Management Plan............................................................................................................................................................... 2,000.00 65002
65/2
Section 66
UNIFORM
66 UNIFORM 66
SECTION 66
UNIFORM
SPECIAL CONDITIONS
Particular SC66.01 This Section shall be read and used in conjunction with the Particular Specification
Specification for Uniform and relevant Conditions of Contract adopted in the Contract.
Particular SC66.02 Where no pre-priced rates are provided in this Section, the rates will be provided
Preamble under individual Term Contract.
For any rates to be provided in this Section, they shall be deemed to allow for the
value of work related to the item and for meeting all other related obligations,
liabilities, risks and profit. Any aspects where the methods of measurement
provided hereunder do not measure any item or exclude the measurement of
any item or part thereof, they shall be deemed to have been included in the
Contract Percentages allowed for other Sections in the Schedules of Rates.
Rates for SC66.03 The item for uniform for Site Personnel and self-employed workers shall
uniform for include for : -
Site Personnel
and self-employed (a) Design, provision, maintenance, and removal of uniform for Site
workers Personnel and self-employed workers;
(b) Preparing, amending as necessary, and submitting to the Maintenance
Surveyor for approval, details of and drawings showing the design of
the uniform items;
(c) Samples and testing thereof;
(d) Replacement of uniform items;
(e) Credit value of the uniform items when returned and removed; and
(f) Joint audit on the wearing of uniform items.
66/1
66 UNIFORM 66
Item Item
UNIFORM
(Note : - No pre-priced rate is provided in this Section. The rate of this item will be provided under individual Term Contract.
The rate set out in this Section will only be paid for, if ordered by the Maintenance Surveyor in writing
and demonstrated compliance with the Particular Specification for Uniform.)
A
Per item $
66001 Uniform for Site Personnel and self-employed workers................................................................................................................................................................ - 66001
66/2
ANNEX 'A' -
DRAWING SCHEDULE AND DRAWINGS FOR
BUILDER'S WORKS
ANNEX 'A' - DRAWING SCHEDULE AND DRAWINGS FOR BUILDER'S WORKS
ANNEX 'A'
DRAWING SCHEDULE AND DRAWINGS FOR BUILDER'S WORKS
Section Drawing No./ Title
Reference
Section 06 - Masonry
Note : The following drawing relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
General Specification for Building issued by Architectural Services Department
http://www.archsd.gov.hk/en/publications-publicity/publications.aspx
Page 10-5 of GS2012 Types of Rubble Walling
Section 10 - Steel and Metal Work
Note : The following drawings relevant to this Section of the Schedule can be viewed on website
via the pathway referred therein : -
Architectural Services Department, Architectural Standard Drawings
http://www.archsd.gov.hk/en/publications-publicity/publications.aspx
9711/A/A01 Type A hoarding - corrugated steel fence general plans
9711/A/A02 Type A hoarding - corrugated steel fence general notes
9711/A/A03 Type A hoarding - corrugated steel fence construction details 1
9711/A/A04 Type A hoarding - corrugated steel fence construction details 2
9711/A/A05 Type A hoarding - corrugated steel fence construction details 3
9711/A/S01 Type A hoarding - corrugated steel fence structural details 1
9711/A/S02 Type A hoarding - corrugated steel fence structural details 2
9711/A/S03 Type A hoarding - corrugated steel fence structural details 3
9711/A/S04 Type A hoarding - corrugated steel fence structural details 4
A/1
ANNEX 'A' - DRAWING SCHEDULE AND DRAWINGS FOR BUILDER'S WORKS
Section Drawing No./ Title
Reference
Section 10 - Steel and Metal Work (Cont'd)
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Architectural Services Department, Architectural Standard Drawings
http://www.archsd.gov.hk/en/publications-publicity/publications.aspx
9711/B/A01 Type B hoarding - covered walkway general plans
9711/B/A02 Type B hoarding - covered walkway general notes
9711/B/A03 Type B hoarding - covered walkway construction details 1
9711/B/A04 Type B hoarding - covered walkway construction details 2
9711/B/A05 Type B hoarding - covered walkway construction details 3
9711/B/A06 Type B hoarding - covered walkway construction details 4
9711/B/A07 Type B hoarding - covered walkway construction details 5
9711/B/S01 Type B hoarding - covered walkway structural details 1
9711/B/S02 Type B hoarding - covered walkway structural details 2
9711/B/S03 Type B hoarding - covered walkway structural details 3
9711/B/S04 Type B hoarding - covered walkway structural details 4
9711/B/S05 Type B hoarding - covered walkway structural details 5
9711/C/A01 Type C hoarding - covered walkway with single deck catch
platform - general plans
9711/C/A02 Type C hoarding - covered walkway with single deck catch
platform - general notes
9711/C/A03 Type C hoarding - covered walkway with single deck catch
platform - construction details 1
9711/C/A04 Type C hoarding - covered walkway with single deck catch
platform - construction details 2
9711/C/A05 Type C hoarding - covered walkway with single deck catch
platform - construction details 3
9711/C/A06 Type C hoarding - covered walkway with single deck catch
platform - construction details 4
9711/C/A07 Type C hoarding - covered walkway with single deck catch
platform - construction details 5
A/2
ANNEX 'A' - DRAWING SCHEDULE AND DRAWINGS FOR BUILDER'S WORKS
Section Drawing No./ Title
Reference
Section 10 - Steel and Metal Work (Cont'd)
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Architectural Services Department, Architectural Standard Drawings
http://www.archsd.gov.hk/en/publications-publicity/publications.aspx
9711/C/S01 Type C hoarding - covered walkway with single deck catch
platform - structural details 1
9711/C/S02 Type C hoarding - covered walkway with single deck catch
platform - structural details 2
9711/C/S03 Type C hoarding - covered walkway with single deck catch
platform - structural details 3
9711/C/S04 Type C hoarding - covered walkway with single deck catch
platform - structural details 4
9711/C/S05 Type C hoarding - covered walkway with single deck catch
platform - structural details 5
9711/D/A01 Type D hoarding - covered walkway with double deck catch
platform - general plans
9711/D/A02 Type D hoarding - covered walkway with double deck catch
platform - general notes
9711/D/A03 Type D hoarding - covered walkway with double deck catch
platform - construction details 1
9711/D/A04 Type D hoarding - covered walkway with double deck catch
platform - construction details 2
9711/D/A05 Type D hoarding - covered walkway with double deck catch
platform - construction details 3
9711/D/A06 Type D hoarding - covered walkway with double deck catch
platform - construction details 4
9711/D/A07 Type D hoarding - covered walkway with double deck catch
platform - construction details 5
9711/D/S01 Type D hoarding - covered walkway with double deck catch
platform - structural details 1
9711/D/S02 Type D hoarding - covered walkway with double deck catch
platform - structural details 2
9711/D/S03 Type D hoarding - covered walkway with double deck catch
platform - structural details 3
9711/D/S04 Type D hoarding - covered walkway with double deck catch
platform - structural details 4
A/3
ANNEX 'A' - DRAWING SCHEDULE AND DRAWINGS FOR BUILDER'S WORKS
Section Drawing No./ Title
Reference
Section 10 - Steel and Metal Work (Cont'd)
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Architectural Services Department, Architectural Standard Drawings
http://www.archsd.gov.hk/en/publications-publicity/publications.aspx
9711/D/S05 Type D hoarding - covered walkway with double deck catch
platform - structural details 5
9711/E/A01 Type E hoarding corrugated steel fence (surface mounted
footing) general plans
9711/E/A02 Type E hoarding corrugated steel fence (surface mounted
footing) general notes
9711/E/A03 Type E hoarding corrugated steel fence (surface mounted
footing) construction details 1
9711/E/A04 Type E hoarding corrugated steel fence (surface mounted
footing) construction details 2
9711/E/A05 Type E hoarding corrugated steel fence (surface mounted
footing) construction details 3
9711/E/S01 Type E hoarding corrugated steel fence (surface mounted
footing) structural details 1
9711/E/S02 Type E hoarding corrugated steel fence (surface mounted
footing) structural details 2
9711/E/S03 Type E hoarding corrugated steel fence (surface mounted
footing) structural details 3
9711/E/S04 Type E hoarding corrugated steel fence (surface mounted
footing) structural details 4
9711/F/A01 Type F hoarding - covered walkway (surface mounted footing)
general plans
9711/F/A02 Type F hoarding - covered walkway (surface mounted footing)
general notes
9711/F/A03 Type F hoarding - covered walkway (surface mounted footing)
construction details 1
9711/F/A04 Type F hoarding - covered walkway (surface mounted footing)
construction details 2
9711/F/A05 Type F hoarding - covered walkway (surface mounted footing)
construction details 3
9711/F/A06 Type F hoarding - covered walkway (surface mounted footing)
construction details 4
A/4
ANNEX 'A' - DRAWING SCHEDULE AND DRAWINGS FOR BUILDER'S WORKS
Section Drawing No./ Title
Reference
Section 10 - Steel and Metal Work (Cont'd)
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Architectural Services Department, Architectural Standard Drawings
http://www.archsd.gov.hk/en/publications-publicity/publications.aspx
9711/F/A07 Type F hoarding - covered walkway (surface mounted footing)
construction details 5
9711/F/S01 Type F hoarding - covered walkway (surface mounted footing)
structural details 1
9711/F/S02 Type F hoarding - covered walkway (surface mounted footing)
structural details 2
9711/F/S03 Type F hoarding - covered walkway (surface mounted footing)
structural details 3
9711/F/S04 Type F hoarding - covered walkway (surface mounted footing)
structural details 4
9711/F/S05 Type F hoarding - covered walkway (surface mounted footing)
structural details 5
9711/G1/A01 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) general notes
9711/G1/A02 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) plans
9711/G1/A03 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) elevation
9711/G1/A04 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) sections
9711/G1/A05 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) construction details 1
9711/G1/A06 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) construction details 2
9711/G1/A07 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) construction details 3
9711/G1/A08 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) construction details 4
9711/G1/A09 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) sited on carriageway / narrow pavement
9711/G1/S01 Type G1 hoarding - covered walkway with single deck catch
platform (surface mounted footing) structural details 1
A/5
ANNEX 'A' - DRAWING SCHEDULE AND DRAWINGS FOR BUILDER'S WORKS
Section Drawing No./ Title
Reference
Section 10 - Steel and Metal Work (Cont'd)
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Architectural Services Department, Architectural Standard Drawings
http://www.archsd.gov.hk/en/publications-publicity/publications.aspx
9711/G1/S02 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) structural details 2
9711/G1/S03 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) structural details 3
9711/G1/S04 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) structural details 4
9711/G1/S05 Type G1 hoarding - covered walkway with single deck catch platform
(surface mounted footing) structural details 5
9711/G2/A01 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) general notes
9711/G2/A02 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) plans
9711/G2/A03 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) elevation
9711/G2/A04 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) sections
9711/G2/A05 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) construction details 1
9711/G2/A06 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) construction details 2
9711/G2/A07 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) construction details 3
9711/G2/A08 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) construction details 4
9711/G2/S01 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) structural details 1
9711/G2/S02 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) structural details 2
9711/G2/S03 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) structural details 3
9711/G2/S04 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) structural details 4
A/6
ANNEX 'A' - DRAWING SCHEDULE AND DRAWINGS FOR BUILDER'S WORKS
Section Drawing No./ Title
Reference
Section 10 - Steel and Metal Work (Cont'd)
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Architectural Services Department, Architectural Standard Drawings
http://www.archsd.gov.hk/en/publications-publicity/publications.aspx
9711/G2/S05 Type G2 hoarding - covered walkway with single deck catch platform
(surface mounted footing) structural details 5
9711/H1/A01 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) general notes
9711/H1/A02 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) plans
9711/H1/A03 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) elevation
9711/H1/A04 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) sections
9711/H1/A05 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) construction details 1
9711/H1/A06 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) construction details 2
9711/H1/A07 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) construction details 3
9711/H1/A08 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) construction details 4
9711/H1/A09 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) sited on carriageway / narrow pavement
9711/H1/S01 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) structural details 1
9711/H1/S02 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) structural details 2
9711/H1/S03 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) structural details 3
9711/H1/S04 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) structural details 4
9711/H1/S05 Type H1 hoarding - covered walkway with double deck catch platform
(surface mounted footing) structural details 5
A/7
ANNEX 'A' - DRAWING SCHEDULE AND DRAWINGS FOR BUILDER'S WORKS
Section Drawing No./ Title
Reference
Section 10 - Steel and Metal Work (Cont'd)
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Architectural Services Department, Architectural Standard Drawings
http://www.archsd.gov.hk/en/publications-publicity/publications.aspx
9711/H2/A01 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) general notes
9711/H2/A02 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) plans
9711/H2/A03 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) elevation
9711/H2/A04 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) sections
9711/H2/A05 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) construction details 1
9711/H2/A06 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) construction details 2
9711/H2/A07 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) construction details 3
9711/H2/A08 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) construction details 4
9711/H2/S01 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) structural details 1
9711/H2/S02 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) structural details 2
9711/H2/S03 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) structural details 3
9711/H2/S04 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) structural details 4
9711/H2/S05 Type H2 hoarding - covered walkway with double deck catch platform
(surface mounted footing) structural details 5
Attached in this Annex 'A'
Total 16 pages Construction Industry Logo Guidelines issued in January 2011
A/8
ANNEX 'A' - DRAWING SCHEDULE AND DRAWINGS FOR BUILDER'S WORKS
Section Drawing No./ Title
Reference
Section 11 - Plastering and Finishes
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Highways Department Standard Drawings - Section 5 Landscape Hard Works
http://www.hyd.gov.hk/en/publications_and_publicity/publications/technical_document/index.html
H 5136 Block paved footway with geogrid
H 5137 Permanent reinstatement of pavement - block paved footway with geogrid
Section 12 - Roadwork and Cable Duct
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Highways Department Standard Drawings - Section 1 Roads
http://www.hyd.gov.hk/en/publications_and_publicity/publications/technical_document/index.html
H 1101 A Typical bituminous pavement construction
H 1102 A Typical concrete pavement construction
H 1118 Precast concrete kerbs (Sheet 1 of 2)
H 1119 Precast concrete kerbs (Sheet 2 of 2)
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Architectural Services Department, Structural Standard Drawings
http://www.archsd.gov.hk/en/publications-publicity/publications.aspx
SD/026 Typical detail of external driveway and carpark ground slab on grade
(5 of 5)
A/9
ANNEX 'A' - DRAWING SCHEDULE AND DRAWINGS FOR BUILDER'S WORKS
Section Drawing No./ Title
Reference
Section 23 - Geotechnical Works
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
General Specification for Building issued by Architectural Services Department (Section 26 Appendix Drawings)
http://www.archsd.gov.hk/en/publications-publicity/publications.aspx
C2104 Tree Ring
C2106/1 Typical detail of soil nail
C2106/2 Soil nail head details
C2106/3 Soil nail head details for sprayed concrete slope surface
C2202 Typical arrangement of rock dowel
C2205 Fixing of wire mesh to rock face
C2302 Filter blanket for fill slope and filling details at slope crest
C2403 Typical arrangement of raking drains
C2404 Relief drain details
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Civil Engineering and Development Department Standard Drawings
http://www.cedd.gov.hk/eng/publications/standards_handbooks_cost/stan_drawing.htm
C2501/1B Temporary safety fence (Type A)
C2501/2B Temporary safety fence (Type A)
C2502/1C Temporary safety fence (Type B)
C2502/2C Temporary safety fence (Type B)
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Highways Department Standard Drawings - Section 2 Street Furniture
http://www.hyd.gov.hk/en/publications_and_publicity/publications/technical_document/index.html
H2112A Beam barriers - Corrugated beam
A/10
ANNEX 'A' - DRAWING SCHEDULE AND DRAWINGS FOR BUILDER'S WORKS
Section Drawing No./ Title
Reference
Section 23 - Geotechnical Works (Cont'd)
Note : The following drawings relevant to this Section of the Schedule can be viewed on website via the pathway referred therein : -
Architectural Services Department, Architectural Standard Drawings
http://www.archsd.gov.hk/en/publications-publicity/publications.aspx
7116_01 (09/00) Display sign for man-made slopes / retaining walls (1 of 5)
7116_02 (09/00) Display sign for man-made slopes / retaining walls (2 of 5)
7116_03 (09/00) Display sign for man-made slopes / retaining walls (3 of 5)
7116_04 (09/00) Display sign for man-made slopes / retaining walls (4 of 5)
7116_05 (09/00) Display sign for man-made slopes / retaining walls (5 of 5)
Attached in this Annex 'A'
Issued in SE Instruction No. 04/2012 by Structural Engineering Branch, Architectural
Services Department
R1043/3 Soil nail (double corrosion protection with wire for TDR)
R1043/3-1 Soil nail (double corrosion protection without wire for TDR)
A/11
A/12
Page 1 of 18
(Not Applicable)
(Not Applicable)
A/13
Page 2 of 18
A/14
CONSTRUCTION INDUSTRY (CI) LOGO DESIGN
This CI logo shall be displayed alternately with the departmental logo on the hoardings installed. The Contractor shall confirm with the
Supervising Officer on the space, size, colours and details of the logo.
Page 4 of 18
A/15
Page 5 of 18
A/16
Page 6 of 18
A/17
CONSTRUCTION INDUSTRY (CI) LOGO DESIGN
This CI logo shall be displayed alternately with the departmental logo on the hoardings installed. The Contractor shall confirm
with the Supervising Officer on the space, size, colours and details of the logo.
Page 8 of 18
A/18
CONSTRUCTION INDUSTRY (CI) LOGO DESIGN
This CI logo shall be displayed alternately with the departmental logo on the hoardings installed. The Contractor
shall confirm with the Supervising Officer on the space, size, colours and details of the logo.
Page 9 of 18
A/19
CONSTRUCTION INDUSTRY (CI) LOGO DESIGN
This CI logo shall be displayed alternately with the departmental logo on the hoardings installed. The Contractor shall
confirm with the Supervising Officer on the space, size, colours and details of the logo.
Page 10 of 18
A/20
CONSTRUCTION INDUSTRY (CI) LOGO DESIGN
This CI logo shall be displayed alternately with the departmental logo on the hoardings installed. The Contractor
shall confirm with the Supervising Officer on the space, size, colours and details of the logo.
Page 11 of 18
A/21
CONSTRUCTION INDUSTRY (CI) LOGO DESIGN
This CI logo shall be displayed alternately with the departmental logo on the hoardings installed. The Contractor
shall confirm with the Supervising Officer on the space, size, colours and details of the logo.
Page 12 of 18
A/22
CONSTRUCTION INDUSTRY (CI) LOGO DESIGN
This CI logo shall be displayed alternately with the departmental logo on the hoardings installed. The Contractor shall
confirm with the Supervising Officer on the space, size, colours and details of the logo.
Page 13 of 18
A/23
CONSTRUCTION INDUSTRY (CI) LOGO DESIGN
This CI logo shall be displayed alternately with the departmental logo on the hoardings installed. The Contractor
shall confirm with the Supervising Officer on the space, size, colours and details of the logo.
Page 14 of 18
A/24
CONSTRUCTION INDUSTRY (CI) LOGO DESIGN
This CI logo shall be displayed alternately with the departmental logo on the hoardings installed. The Contractor
shall confirm with the Supervising Officer on the space, size, colours and details of the logo.
Page 15 of 18
A/25
CONSTRUCTION INDUSTRY (CI) LOGO DESIGN
This CI logo shall be displayed alternately with the departmental logo on the hoardings installed. The Contractor shall
confirm with the Supervising Officer on the space, size, colours and details of the logo.
Page 16 of 18
A/26
CONSTRUCTION INDUSTRY (CI) LOGO DESIGN
This CI logo shall be displayed alternately with the departmental logo on the hoardings installed. The Contractor
shall confirm with the Supervising Officer on the space, size, colours and details of the logo.
Page 17 of 18
Supplement to Construction Industry (CI) Logo Guidelines dated January 2011
A/27
CONSTRUCTION INDUSTRY (CI) LOGO DESIGN
This CI logo shall be displayed alternately with the departmental logo on the hoardings installed. The Contractor
shall confirm with the Supervising Officer on the space, size, colours and details of the logo.
Page 18 of 18
A/28
A/29
ANNEX 'B' -
GROUPING OF PLANT MATERIALS
ANNEX 'B' - GROUPING OF PLANT MATERIALS
ANNEX 'B' - GROUPING OF PLANT MATERIALS
Trees Grouping
(1) Group A consists of : -
Acacia auriculiformis
Acacia confusa
Acacia mangium
Bauhinia purpurea
Bauhinia variegata
Bischofia polycarpa
Bombax ceiba
Cassia fistula
Ca sia surattensis
Casuarina equisetifolia
Delonix regia
Elaeocarpus h inanensis
Erythrina corallodendron
Erythrina variegata
Eucalyptus camaldulensis
Eucalyptus citriodora
Eucalyptus robusta
Eucalypt s tere icornis
Eucalyptus torelliana ()
Ficus altissima
Ficus benjami a
Ficus binnendijkii Alii
Ficus elastica ()
Ficus rumphii ()
Ficus wightiana
Lagerstroemia speciosa ()
Lophostemon conf rtus
Melaleuca quinquenervia
Mesua ferrea
Michelia x alba
Peltophoru pterocarpum
Plumeria obtusa
Plumeria rubra
Salix babylonica
Spathodea campanulata
Syzygium cumini
Syzygium jambos
Termi alia c tappa
Terminalia mantaly
B/1
ANNEX 'B' - GROUPING OF PLANT MATERIALS
Trees Grouping (Cont'd)
(2) Group B consists of : -
Aleurites moluccana
Alnus japonica
Bauhinia variegata var. candida
Callistemon rigidus
Callistemon viminalis
Camptotheca acuminata
Cananga odorata ()
Cassia siamea
Cassia spectabilis
Ceiba pentandra ()
Chorisia speciosa
Chukrasia tabularia
Crateva trifoliata
Crateva unilocularis
Dracontomelon duperreanum
Elaeocarpus apiculatus
Elaeocarpus balansae
Elaeocarpus decipiens
Elaeocarpus sylvestris ()
Erythrina crista-galli
Erythrina speciosa
Erythrina variegataParcellii
Eucalyptus calophylla
Ficus benjamina Variegata
Ficus religiosa
Firmiana simplex
Glochidion hirsutum
Grevillea banksii
Grevillea robusta
Jacaranda mimosifolia
Khaya senegalensis ()
Koelreuteria bipinnata
Koelreuteria elegans
Ligustrum amamianum
Machilus chekiangensis ()
Machilus gamblei ()
Machilus pauhoi
Magnolia grandiflora ()
Melia azedarach ()()
Melicope pteleifolia ()
Michelia champaca
Michelia macclurei
Nauclea orientalis
Pandanus tectorius
Pterocarpus indicus ()
Pterocarya stenoptera
Schefflera actinophylla ()
Schima wallichii ()
B/2
ANNEX 'B' - GROUPING OF PLANT MATERIALS
Trees Grouping (Cont'd)
(2) Group B consists of : - (Cont'd)
Tabebuia chrysantha ()
Tabebuia impetiginosa
Tabebuia rosea ()
Tamarindus indica ()
Tectona grandis
Tipuana tipu
Toona sinensis
Vernicia fordii ()
(3) Group C consists of : -
Adenanthera microsperma
Albizia saman
Alstonia scholaris
Artocarpus altilis
Artocarpus macrocarpus
Bauhinia tomentosa
Bixa orellana ()
Brachychiton acerifolius
Cassia javanica
Cassia javanica var. indochinensis
Dillenia indica
Dracaena draco ()
Elaeocarpus angustifolius
Erythrina caffra
Firmiana simplex
Garcinia spicata
Garcinia subelliptica
Osmanthus fragrans ()
Paulownia fortunei
Paulownia tomentosa
Salix babylonica var Glandulipilosa
Sophora japonica
Swietenia mahogani
Xanthostemon chrysanthus
(4) Group D consists of : -
Albizia lebbeck
Bischofia javanica
Bridelia tomentosa
Broussonetia papyrifera
Canarium album
Castanopsis fissa ()
Celtis sinensis
Celtis timorensis
Cerbera manghas
Choerospondias axillaris ()
Cinnamomum burmannii
Cinnamomum camphora
Cinnamomum parthenoxylon
B/3
ANNEX 'B' - GROUPING OF PLANT MATERIALS
Trees Grouping (Cont'd)
(4) Group D consists of : - (Cont'd)
Cleistocalyx operculatus
Diospyros morrisiana
Elaeocarpus chinensis ()
Ficus hirta ()
Ficus hispida ()
Ficus microcarpa
Ficus pandurata
Ficus superba var. japonica
Ficus variegata var. chlorocarpa
Ficus virens var. sublanceolata
Gordonia axillaris
Hibiscus tiliaceus
Ilex rotunda
Ilex rotunda var. microcarpa
Liquidambar formosana ()
Lithocarpus glaber
Litsea glutinosa
Litsea monopetala
Macaranga tanarius
Mallotus paniculatus
Microcos paniculata ()
Myrica rubra
Phyllanthus emblica
Pongamia pinnata
Rhus hypoleuca ()
Rhus succedanea ()
Sapindus saponaria ()
Sapium discolor
Sapium sebiferum
Schefflera heptaphylla ()
Schima superba ()
Sterculia lanceolata
Syzygium levinei ()
Thespesia populnea ()
(5) Group E consists of : -
Alangium chinense
Aporusa dioica ()
Archidendron clypearia
Bauhinia blakeana
Camellia oleifera
Castanopsis fabri ()
Cordia dichotoma
Cratoxylum cochinchinense
Cryptocarya chinensis
Cryptocarya concinna ()
Cyclobalanopsis championii
Cyclobalanopsis edithiae
B/4
ANNEX 'B' - GROUPING OF PLANT MATERIALS
Trees Grouping (Cont'd)
(5) Group E consists of : - (Cont'd)
Cyclobalanopsis myrsinifolia
Cyclobalanopsis neglecta
Dalbergia balansae
Endospermum chinense
Garcinia oblongifolia ()
Homalium cochinchinensis
Machilus breviflora ()
Machilus thunbergii
Machilus velutina
Ormosia emarginata
Oroxylum indicum ()
Osmanthus marginatus (O. sinensis)
Pistacia chinensis
Prunus phaeosticta
Pyrus calleryana
Reevesia thyrsoidea
Symplocos glauca
Syzygium hancei ()
Tetradium glabrifolium
Tutcheria spectabilis
Ulmus parvifolia
Viburnum odoratissimum
(6) Group F consists of : -
Ailanthus fordii
Aquilaria sinensis ()
Camellia crapnelliana ()
Camellia granthamiana ()
Litsea cubeba ()
Rhodoleia championii ()
(7) Group G consists of other tree species : -
B/5
ANNEX 'B' - GROUPING OF PLANT MATERIALS
Conifers Grouping and Sizes
(i) The overall heights and groups are as follows:
Small Conifer Large Conifer Extra-large Conifer
(overall height in mm) (overall height in mm) (overall height in mm)
Group A Upto 1500 1501-2700 Exceeding 2700
Group B Upto 1500 1501-2100 Exceeding 2100
Group C Upto 1500 1501-1800 Exceeding 1800
Group D Upto 1500 1501-2100 Exceeding 2100
(ii) Conifers are divided into 4 groups by species:
Group A consists of:
Araucaria cunninghamii ()
Araucaria heterophylla
Cunninghamia lanceolata
Cupressus funebris ()
Glyptostrobus pensilis
Keteleeria fortunei
Taxodium distichum
Group B consists of :
Podocarpus macrophyllus
Thuja orientalis
Group C consists of :
Juniperus chinensis
Juniperus chinensis cv.Kaizuca
Nageia nagi
Group D consists of other conifer species:
B/6
ANNEX 'B' - GROUPING OF PLANT MATERIALS
Palms and Cycas Grouping and Sizes
(i) The overall heights and groups are as follows:
Small Palm Medium Palm Large Palm Extra-large Palm
(overall height (overall height (overall height (overall height
in mm) in mm) in mm) in mm)
Group A 300-500 501-1000 1000-1500 Exceeding 1500
Group B 500-1000 1001-1500 1500-2500 Exceeding 2500
Group C 500-1000 1001-2000 2000-3000 Exceeding 3000
Group D 2000-3000 3001-4000 4000-5000 Exceeding 5000
Group E 500-1000 1001-1500 NA NA
Group F 500-1000 1001-2000 2000-3000 Exceeding 3000
(ii) Palms are divided into 6 groups by species:
Group A consists of:
Cycas revoluta ()
Zamia furfuracea ()
Group B consists of:
Arenga pinnata ()
Elaeis guineensis ()
Hyophorbe lagenicaulis
Hyophorbe verschaffeltii
Livistona chinensis
Neodypsis decaryi
Phoenix canariensis
Phoenix dactylifera ()
Phoenix hanceana ()
Phoenix sylvestris
Ravenala madagascariensis
Trachycarpus fortunei
Washingtonia robusta
B/7
ANNEX 'B' - GROUPING OF PLANT MATERIALS
Palms and Cycas Grouping and Sizes (Cont'd)
(ii) Palms are divided into 6 groups by species: (Cont'd)
Group C consists of:
Bismarckia nobilis
Caryota mitis ()
Caryota ochlandra
Chrysalidocarpus lutescens
Phoenix roebelenii
Group D consists of:
Archontophoenix alexandrae
Areca triandra Roxb
Butia capitata Becc.
Cocos nucifera
Roystonea regia ()
Syagrus romanzoffiana ()
Wodyetia bifurcata
Group E consists of:
Chamaedorea elegans
Chamaedorea erumpens
Chamaedorea humilis ()
Pritchardia gaudichaudii
Rhapis excelsa
Rhapis gracilis
Rhapis humilis ()
Group F consists of Other palm species
B/8
ANNEX 'C' -
TABLES OF METAL WEIGHTS, ETC.
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
Table Page
1 Metric/Imperial equivalents.......................................................................................................... C/2
2 Mass (Weight) of wire.................................................................................................................. C/3
3 Mass (Weight) of sheet lead......................................................................................................... C/4
4 Mass (Weight) of sheet zinc......................................................................................................... C/4
5 Mass (Weight) of sheet metal....................................................................................................... C/5 - C/6
6 Mass (Weight) of metal plates...................................................................................................... C/7
7 Mass (Weight) of mild steel round bars....................................................................................... C/8
8 Mass (Weight) of rolled steel square bars.................................................................................... C/8
9 Mass (Weight) of rolled steel flat bars......................................................................................... C/9
10 Mass (Weight) of black bolts and nuts......................................................................................... C/10
11 Mass (Weight) of steel cup-headed rivets..................................................................................... C/11
12 Mass (Weight) of rolled steel equal angles................................................................................... C/12
13 Mass (Weight) of rolled steel unequal angles............................................................................... C/12
14 Mass (Weight) of rolled steel universal beams............................................................................. C/13 - C/14
15 Mass (Weight) of rolled steel universal columns......................................................................... C/15
16 Mass (Weight) of rolled steel universal bearing piles.................................................................. C/16
17 Mass (Weight) of rolled steel joists with taper flanges................................................................ C/17
18 Mass (Weight) of rolled steel structural tees cut from universal beams....................................... C/18 - C/19
19 Mass (Weight) of rolled steel structural tees cut from universal columns.................................... C/20
20 Mass (Weight) of rolled steel parallel flange channels................................................................. C/21
21 Mass (Weight) of rolled steel equal flange tees with radiused root and toes................................ C/21
22 Mass (Weight) of rolled steel circular hollow sections................................................................ C/22
23 Mass (Weight) of rolled steel square hollow sections.................................................................. C/23
24 Mass (Weight) of rolled steel rectangular hollow sections........................................................... C/24
25 Mass (Weight) of solid aluminium round bars............................................................................. C/25
26 Mass (Weight) of solid aluminium square bars............................................................................ C/25
27 Mass (Weight) of solid aluminium flats....................................................................................... C/26
28 Mass (Weight) of aluminium equal angles................................................................................... C/27
29 Mass (Weight) of aluminium unequal angles............................................................................... C/27
30 Mass (Weight) of aluminium channels......................................................................................... C/28
31 Mass (Weight) of aluminium tee sections.................................................................................... C/29
32 Mass (Weight) of aluminium round hollow tubes........................................................................ C/30
33 Mass (Weight) of aluminium square hollow sections.................................................................. C/31
34 Mass (Weight) of aluminium rectangular hollow sections........................................................... C/31
35 Mass (Weight) of stainless steel flat bars..................................................................................... C/32
36 Mass (Weight) of stainless steel angles........................................................................................ C/32
37 Mass (Weight) of stainless steel channels.................................................................................... C/32
38 Mass (Weight) of stainless steel round tubes............................................................................... C/32
39 Mass (Weight) of stainless steel square hollow sections.............................................................. C/32
40 Mass (Weight) of stainless steel rectangular hollow sections...................................................... C/32
41 Standard BRC fabrics square meshes........................................................................................... C/33
42 Standard BRC fabrics rectangular meshes................................................................................... C/33
43 Mass (Weight) of steel sheet piles................................................................................................ C/34
44 Mass (Weight) of steel chequer plate........................................................................................... C/34
C/1
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 1
METRIC/IMPERIAL EQUIVALENTS
Metric sizes Imperial
or dimensions equivalents
(millimetres) (inches)
3 1/8
6 1/4
10 3/8
13 1/2
16 5/8
19 3/4
22 7/8
25 1
32 1-1/4
35 1-3/8
38 1-1/2
44 1-3/4
51 2
57 2-1/4
64 2-1/2
70 2-3/4
76 3
83 3-1/4
89 3-1/2
95 3-3/4
100 4
125 5
150 6
175 7
200 8
225 9
250 10
275 11
300 12
450 18
600 24
750 30
900 36
1,200 48
Examples : -
1. An imperial sized scantling measuring 2" x 3" shall be paid for as a 50 x 75 mm scantling.
2. An imperial sized tower bolt measuring 9" long shall be paid for as a 225 mm long tower bolt.
C/2
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 2
MASS (WEIGHT) OF WIRE
Preferred kg/100 m Preferred kg/100 m
diameter Gauge diameter Gauge
(mm) S.W.G. diameter Steel Copper (mm) S.W.G. diameter Steel Copper
BS 4391 : (mm) BS 4391 : (mm)
1972 1972
40 0.122 0.01 0.01 1.000 0.62 0.66
0.125 0.01 0.01 19 1.016 0.64 0.68
39 0.132 0.01 0.01 1.200 0.89 0.95
38 0.152 0.01 0.02 18 1.219 0.92 0.98
0.160 0.02 0.02 17 1.422 1.25 1.34
37 0.173 0.02 0.02 1.600 1.58 1.69
36 0.193 0.02 0.02 16 1.626 1.63 1.75
0.200 0.02 0.02 15 1.829 2.06 2.21
35 0.213 0.03 0.03 2.000 2.47 2.64
34 0.234 0.03 0.04 14 2.032 2.55 2.73
0.250 0.04 0.04 13 2.337 3.37 3.61
33 0.254 0.04 0.04 2.500 3.85 4.13
32 0.274 0.05 0.05 12 2.642 4.31 4.62
31 0.295 0.05 0.06 11 2.946 5.35 5.74
0.300 0.06 0.06 3.000 5.55 5.95
30 0.315 0.06 0.07 10 3.251 6.52 6.99
29 0.345 0.07 0.08 9 3.658 8.25 8.85
28 0.376 0.09 0.09 4.000 9.87 10.58
0.400 0.10 0.11 8 4.064 10.19 10.92
27 0.417 0.11 0.11 7 4.470 12.32 13.21
26 0.457 0.13 0.14 6 4.877 14.67 15.73
0.500 0.15 0.17 5.000 15.42 16.53
25 0.508 0.16 0.17 5 5.385 17.89 19.17
24 0.559 0.19 0.21 4 5.893 21.42 22.96
0.600 0.22 0.24 6.000 22.20 23.80
23 0.610 0.23 0.25 3 6.401 25.27 27.09
0.700 0.30 0.32 2 7.010 30.31 32.49
22 0.711 0.31 0.33 1 7.620 35.81 38.39
0.800 0.39 0.42 8.000 39.47 42.32
21 0.813 0.41 0.44
0.900 0.50 0.54
20 0.914 0.52 0.55
Note :-
For mass of iron wire, multiply the mass of steel wire by 0.991.
For mass of brass wire, multiply the mass of steel wire by 1.072.
C/3
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 3
MASS (WEIGHT) OF SHEET LEAD
Code Thickness kg/m* Colour
number (mm) marking
3 1.25 14.18 green
4 1.80 20.41 blue
5 2.24 25.40 red
6 2.50 28.36 black
7 3.15 35.72 white
8 3.55 40.26 orange
* Basic value : 11,450 kg/m
TABLE 4
MASS (WEIGHT) OF SHEET ZINC
Metric
thickness Zinc Gauge kg/m*
BS-DD5 : gauge thickness
1971 (mm)
1 0.102 0.73
2 0.152 1.09
3 0.178 1.28
4 0.203 1.46
0.25 1.80
5 0.254 1.83
6 0.273 1.97
0.30 2.16
7 0.330 2.38
8 0.381 2.74
0.40 2.88
9 0.432 3.11
10 0.483 3.48
0.50 3.60
11 0.559 4.02
0.60 4.32
12 0.635 4.57
0.70 5.04
13 0.711 5.12
14 0.787 5.67
0.80 5.76
0.90 6.48
15 0.914 6.58
1.00 7.20
16 1.041 7.50
17 1.168 8.41
1.20 8.64
18 1.295 9.32
19 1.448 10.43
1.60 20 1.600 11.52
21 1.778 12.80
2.00 14.40
* Basic value : 7,200 kg/m
C/4
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 5
MASS (WEIGHT) OF SHEET METAL
Metric Gauge kg/m*
thickness S.W.G. thickness Stainless
(mm) (mm) Steel steel Copper Aluminium
34 0.234 1.84 1.84 2.09 0.63
0.25 1.96 1.97 2.23 0.68
33 0.254 1.99 2.00 2.27 0.69
32 0.274 2.15 2.16 2.45 0.74
31 0.295 2.31 2.32 2.64 0.80
0.30 2.35 2.36 2.68 0.81
30 0.315 2.47 2.48 2.82 0.85
29 0.345 2.71 2.72 3.08 0.93
28 0.376 2.95 2.96 3.36 1.02
0.40 3.14 3.15 3.58 1.08
27 0.417 3.27 3.29 3.73 1.13
26 0.457 3.58 3.60 4.08 1.24
0.50 3.92 3.94 4.47 1.35
25 0.508 3.98 4.00 4.54 1.38
24 0.559 4.38 4.41 5.00 1.51
0.60 4.71 4.73 5.36 1.62
23 0.610 4.78 4.81 5.45 1.65
0.70 5.49 5.52 6.26 1.89
22 0.711 5.58 5.60 6.35 1.92
0.80 6.27 6.30 7.15 2.17
21 0.813 6.38 6.41 7.27 2.20
0.90 7.06 7.09 8.04 2.44
20 0.914 7.17 7.20 8.17 2.47
1.00 7.84 7.88 8.94 2.71
19 1.016 7.97 8.01 9.08 2.75
1.20 9.41 9.46 10.73 3.25
18 1.219 9.56 9.61 10.90 3.30
17 1.422 11.15 11.21 12.71 3.85
1.60 12.55 12.61 14.30 4.33
16 1.626 12.75 12.81 14.53 4.40
15 1.829 14.34 14.41 16.35 4.95
2.00 15.69 15.76 17.88 5.41
14 2.032 15.94 16.01 18.16 5.50
13 2.337 18.33 18.42 20.89 6.33
2.50 19.61 19.70 22.35 6.77
12 2.642 20.72 20.82 23.61 7.15
11 2.946 23.11 23.22 26.33 7.97
C/5
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 5 (CONT'D)
MASS (WEIGHT) OF SHEET METAL (CONT'D)
Metric Gauge kg/m*
thickness S.W.G. thickness Stainless
(mm) (mm) Steel steel Copper Aluminium
3.00 23.53 23.64 26.81 8.12
10 3.251 25.50 25.62 29.06 8.80
9 3.658 28.69 28.83 32.70 9.90
4.00 31.37 31.52 35.75 10.83
8 4.064 31.87 32.03 36.32 11.00
7 4.470 35.06 35.23 39.95 12.10
6 4.877 38.25 38.44 43.59 13.20
5.00 39.22 39.41 44.69 13.54
5 5.385 42.23 42.44 48.13 14.58
4 5.893 46.22 46.44 52.67 15.95
6.00 47.06 47.29 53.63 16.24
3 6.401 50.20 50.45 57.21 17.33
2 7.010 54.98 55.25 62.66 18.98
1 7.620 59.76 60.05 68.11 20.63
8.00 62.74 63.05 71.50 21.66
* Basic value : Mild steel 7,843 kg/m
Stainless steel 7,881 kg/m
Copper 8,938 kg/m
Aluminium 2,707 kg/m
For mass of iron sheeting, multiply the mass of steel sheeting by 0.991.
For mass of brass sheeting, multiply the mass of steel sheeting by 1.072.
For mass of sheeting galvanized on both sides, add 0.730 kg/m.
C/6
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 6
MASS (WEIGHT) OF METAL PLATES
Metric Imperial Metric kg/m*
thickness thickness equivalents Stainless
(mm) (inches) (mm) Steel steel Copper Aluminium
1/16 1.59 12.47 12.53 14.21 4.30
1.60 12.55 12.61 14.30 4.33
2.00 15.69 15.76 17.88 5.41
3.00 23.53 23.64 26.81 8.12
1/8 3.18 24.94 25.06 28.42 8.61
4.00 31.37 31.52 35.75 10.83
3/16 4.76 37.33 37.51 42.54 12.89
5.00 39.22 39.41 44.69 13.54
6.00 47.06 47.29 53.63 16.24
1/4 6.35 49.80 50.04 56.76 17.19
8.00 62.74 63.05 71.50 21.66
3/8 9.53 74.74 75.11 85.18 25.80
10.00 78.43 78.81 89.38 27.07
12.00 94.12 94.57 107.26 32.48
1/2 12.70 99.61 100.09 113.51 34.38
15.00 117.65 118.22 134.07 40.61
5/8 15.88 124.55 125.15 141.94 42.99
18.00 141.17 141.86 160.88 48.73
3/4 19.05 149.41 150.13 170.27 51.57
20.00 156.86 157.62 178.76 54.14
7/8 22.23 174.35 175.19 198.69 60.18
25.00 196.08 197.03 223.45 67.68
1 25.40 199.21 200.18 227.03 68.76
* Basic value : Mild steel 7,843 kg/m
Stainless steel 7,881 kg/m
Copper 8,938 kg/m
Aluminium 2,707 kg/m
For mass of iron sheeting, multiply the mass of steel sheeting by 0.991.
For mass of brass sheeting, multiply the mass of steel sheeting by 1.072.
For mass of sheeting galvanized on both sides, add 0.730 kg/m.
C/7
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 7 TABLE 8
MASS (WEIGHT) OF MASS (WEIGHT) OF
MILD STEEL ROUND BARS ROLLED STEEL SQUARE BARS
Preferred Metric Recom- Metric
metric equivalents mended equivalents
diameter Imperial of kg/m* metric size Imperial of kg/m*
(mm) sizes imperial (mm) sizes imperial
BS 4461 : (inches) sizes BS 4429 : (inches) sizes
1971 (mm) 1972 (mm)
6 0.22 1/4 6.350 0.32
1/4 6.350 0.25 5/16 7.938 0.49
8 0.39 3/8 9.525 0.71
3/8 9.525 0.56 10 0.78
10 0.62 7/16 11.112 0.97
12 0.89 12 1.13
1/2 12.700 0.99 1/2 12.700 1.26
5/8 15.875 1.55 14 1.54
16 1.58 9/16 14.288 1.60
3/4 19.050 2.24 5/8 15.875 1.98
20 2.46 16 2.01
7/8 22.225 3.04 11/16 17.462 2.39
25 3.85 18 2.54
1 25.400 3.98 3/4 19.050 2.85
1-1/8 28.575 5.03 20 3.14
1-1/4 31.750 6.21 13/16 20.638 3.34
32 6.31 7/8 22.225 3.87
1-3/8 34.925 7.52 15/16 23.812 4.45
1-1/2 38.100 8.95 25 4.90
40 9.86 1 25.400 5.06
1-5/8 41.275 10.50 28 6.15
1-3/4 44.450 12.18 1-1/8 28.575 6.40
1-7/8 47.625 13.98 1-1/4 31.750 7.91
2 50.800 15.90 32 8.03
1-3/8 34.925 9.57
35 9.61
1-1/2 38.100 11.38
40 12.55
1-5/8 41.275 13.36
1-3/4 44.450 15.50
1-7/8 47.625 17.80
2 50.800 20.24
* Basic value : Mild steel 7,843 kg/m
For mass of cast iron bars, multiply the mass of steel bars by 0.919.
For mass of wrought iron bars, multiply the mass of steel bars by 0.991.
For mass of brass bars, multiply the mass of steel bars by 1.072.
For mass of copper bars, multiply the mass of steel bars by 1.134.
C/8
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 9
MASS (WEIGHT) OF ROLLED STEEL FLAT BARS
Width kg/m*
(mm) Thickness (mm)
1 2 3 4 5 6 7 8 9 10 20 30 40 50
5 0.04 0.08 0.12 0.16 0.20 0.24 0.27 0.31 0.35 0.39 0.78 1.18 1.57 1.96
10 0.08 0.16 0.24 0.31 0.39 0.47 0.55 0.63 0.71 0.78 1.57 2.35 3.14 3.92
15 0.12 0.24 0.35 0.47 0.59 0.71 0.82 0.94 1.06 1.18 2.35 3.53 4.71 5.88
20 0.16 0.31 0.47 0.63 0.78 0.94 1.10 1.25 1.41 1.57 3.14 4.71 6.27 7.84
25 0.20 0.39 0.59 0.78 0.98 1.18 1.37 1.57 1.76 1.96 3.92 5.88 7.84 9.80
30 0.24 0.47 0.71 0.94 1.18 1.41 1.65 1.88 2.12 2.35 4.71 7.06 9.41 11.76
35 0.27 0.55 0.82 1.10 1.37 1.65 1.92 2.20 2.47 2.75 5.49 8.24 10.98 13.73
40 0.31 0.63 0.94 1.25 1.57 1.88 2.20 2.51 2.82 3.14 6.27 9.41 12.55 15.69
45 0.35 0.71 1.06 1.41 1.76 2.12 2.47 2.82 3.18 3.53 7.06 10.59 14.12 17.65
50 0.39 0.78 1.18 1.57 1.96 2.35 2.75 3.14 3.53 3.92 7.84 11.76 15.69 19.61
55 0.43 0.86 1.29 1.73 2.16 2.59 3.02 3.45 3.88 4.31 8.63 12.94 17.25 21.57
60 0.47 0.94 1.41 1.88 2.35 2.82 3.29 3.76 4.24 4.71 9.41 14.12 18.82 23.53
65 0.51 1.02 1.53 2.04 2.55 3.06 3.57 4.08 4.59 5.10 10.20 15.29 20.39 25.49
70 0.55 1.10 1.65 2.20 2.75 3.29 3.84 4.39 4.94 5.49 10.98 16.47 21.96 27.45
75 0.59 1.18 1.76 2.35 2.94 3.53 4.12 4.71 5.29 5.88 11.76 17.65 23.53 29.41
80 0.63 1.25 1.88 2.51 3.14 3.76 4.39 5.02 5.65 6.27 12.55 18.82 25.10 31.37
85 0.67 1.33 2.00 2.67 3.33 4.00 4.67 5.33 6.00 6.67 13.33 20.00 26.67 33.33
90 0.71 1.41 2.12 2.82 3.53 4.24 4.94 5.65 6.35 7.06 14.12 21.18 28.23 35.29
95 0.75 1.49 2.24 2.98 3.73 4.47 5.22 5.96 6.71 7.45 14.90 22.35 29.80 37.25
100 0.78 1.57 2.35 3.14 3.92 4.71 5.49 6.27 7.06 7.84 15.69 23.53 31.37 39.22
110 0.86 1.73 2.59 3.45 4.31 5.18 6.04 6.90 7.76 8.63 17.25 25.88 34.51 43.14
120 0.94 1.88 2.82 3.76 4.71 5.65 6.59 7.53 8.47 9.41 18.82 28.23 37.65 47.06
130 1.02 2.04 3.06 4.08 5.10 6.12 7.14 8.16 9.18 10.20 20.39 30.59 40.78 50.98
140 1.10 2.20 3.29 4.39 5.49 6.59 7.69 8.78 9.88 10.98 21.96 32.94 43.92 54.90
150 1.18 2.35 3.53 4.71 5.88 7.06 8.24 9.41 10.59 11.76 23.53 35.29 47.06 58.82
160 1.25 2.51 3.76 5.02 6.27 7.53 8.78 10.04 11.29 12.55 25.10 37.65 50.20 62.74
170 1.33 2.67 4.00 5.33 6.67 8.00 9.33 10.67 12.00 13.33 26.67 40.00 53.33 66.67
180 1.41 2.82 4.24 5.65 7.06 8.47 9.88 11.29 12.71 14.12 28.23 42.35 56.47 70.59
190 1.49 2.98 4.47 5.96 7.45 8.94 10.43 11.92 13.41 14.90 29.80 44.71 59.61 74.51
200 1.57 3.14 4.71 6.27 7.84 9.41 10.98 12.55 14.12 15.69 31.37 47.06 62.74 78.43
210 1.65 3.29 4.94 6.59 8.24 9.88 11.53 13.18 14.82 16.47 32.94 49.41 65.88 82.35
220 1.73 3.45 5.18 6.90 8.63 10.35 12.08 13.80 15.53 17.25 34.51 51.76 69.02 86.27
230 1.80 3.61 5.41 7.22 9.02 10.82 12.63 14.43 16.24 18.04 36.08 54.12 72.16 90.19
240 1.88 3.76 5.65 7.53 9.41 11.29 13.18 15.06 16.94 18.82 37.65 56.47 75.29 94.12
250 1.96 3.92 5.88 7.84 9.80 11.76 13.73 15.69 17.65 19.61 39.22 58.82 78.43 98.04
260 2.04 4.08 6.12 8.16 10.20 12.24 14.27 16.31 18.35 20.39 40.78 61.18 81.57 101.96
270 2.12 4.24 6.35 8.47 10.59 12.71 14.82 16.94 19.06 21.18 42.35 63.53 84.70 105.88
280 2.20 4.39 6.59 8.78 10.98 13.18 15.37 17.57 19.76 21.96 43.92 65.88 87.84 109.80
290 2.27 4.55 6.82 9.10 11.37 13.65 15.92 18.20 20.47 22.74 45.49 68.23 90.98 113.72
300 2.35 4.71 7.06 9.41 11.76 14.12 16.47 18.82 21.18 23.53 47.06 70.59 94.12 117.65
310 2.43 4.86 7.29 9.73 12.16 14.59 17.02 19.45 21.88 24.31 48.63 72.94 97.25 121.57
320 2.51 5.02 7.53 10.04 12.55 15.06 17.57 20.08 22.59 25.10 50.20 75.29 100.39 125.49
330 2.59 5.18 7.76 10.35 12.94 15.53 18.12 20.71 23.29 25.88 51.76 77.65 103.53 129.41
340 2.67 5.33 8.00 10.67 13.33 16.00 18.67 21.33 24.00 26.67 53.33 80.00 106.66 133.33
350 2.75 5.49 8.24 10.98 13.73 16.47 19.22 21.96 24.71 27.45 54.90 82.35 109.80 137.25
360 2.82 5.65 8.47 11.29 14.12 16.94 19.76 22.59 25.41 28.23 56.47 84.70 112.94 141.17
370 2.90 5.80 8.71 11.61 14.51 17.41 20.31 23.22 26.12 29.02 58.04 87.06 116.08 145.10
380 2.98 5.96 8.94 11.92 14.90 17.88 20.86 23.84 26.82 29.80 59.61 89.41 119.21 149.02
390 3.06 6.12 9.18 12.24 15.29 18.35 21.41 24.47 27.53 30.59 61.18 91.76 122.35 152.94
400 3.14 6.27 9.41 12.55 15.69 18.82 21.96 25.10 28.23 31.37 62.74 94.12 125.49 156.86
410 3.22 6.43 9.65 12.86 16.08 19.29 22.51 25.73 28.94 32.16 64.31 96.47 128.63 160.78
420 3.29 6.59 9.88 13.18 16.47 19.76 23.06 26.35 29.65 32.94 65.88 98.82 131.76 164.70
430 3.37 6.74 10.12 13.49 16.86 20.23 23.61 26.98 30.35 33.72 67.45 101.17 134.90 168.62
440 3.45 6.90 10.35 13.80 17.25 20.71 24.16 27.61 31.06 34.51 69.02 103.53 138.04 172.55
450 3.53 7.06 10.59 14.12 17.65 21.18 24.71 28.23 31.76 35.29 70.59 105.88 141.17 176.47
460 3.61 7.22 10.82 14.43 18.04 21.65 25.25 28.86 32.47 36.08 72.16 108.23 144.31 180.39
470 3.69 7.37 11.06 14.74 18.43 22.12 25.80 29.49 33.18 36.86 73.72 110.59 147.45 184.31
480 3.76 7.53 11.29 15.06 18.82 22.59 26.35 30.12 33.88 37.65 75.29 112.94 150.59 188.23
490 3.84 7.69 11.53 15.37 19.22 23.06 26.90 30.74 34.59 38.43 76.86 115.29 153.72 192.15
500 3.92 7.84 11.76 15.69 19.61 23.53 27.45 31.37 35.29 39.22 78.43 117.65 156.86 196.08
* Basic value : Mild steel 7,843 kg/m
For mass of cast iron bars, multiply the mass of steel bars by 0.919.
For mass of wrought iron bars, multiply the mass of steel bars by 0.991.
For mass of brass bars, multiply the mass of steel bars by 1.072.
For mass of copper bars, multiply the mass of steel bars by 1.134.
For mass of lead bars, multiply the mass of steel bars by 1.454.
C/9
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 10
MASS (WEIGHT) OF BS 4190 ISO METRIC BLACK BOLTS WITH NUT
Length Approximate mass in kilogrammes per 1,000 bolts complete
under including hexagon head and one nut each
head Nominal size of bolt
(mm) M6 M8 M10 M12 M16 M20 M24 M30 M36 M42 M48
25 8.97 18.70 36.60 52.50 - - - - - - -
30 10.10 20.70 39.10 56.10 107.00 186.00 - - - - -
35 11.20 22.70 42.20 59.70 114.00 196.00 - - - - -
40 12.30 24.70 45.30 64.10 121.00 207.00 347.00 - - - -
45 13.40 26.70 48.40 68.50 128.00 217.00 362.00 - - - -
50 14.50 28.70 51.50 72.90 136.00 227.00 377.00 - - - -
55 15.60 30.70 54.60 77.30 144.00 238.00 392.00 - - - -
60 16.70 32.70 57.70 81.70 152.00 251.00 407.00 - - - -
65 17.80 34.70 60.80 86.10 160.00 264.00 422.00 - - - -
70 18.90 36.70 63.90 90.50 168.00 277.00 440.00 - - - -
75 20.00 38.70 67.00 95.00 176.00 290.00 458.00 - - - -
80 21.10 40.70 70.10 100.00 182.00 303.00 476.00 853.00 - - -
90 - 44.70 76.30 109.00 198.00 329.00 511.00 908.00 - - -
100 - 48.70 82.50 118.00 214.00 355.00 547.00 963.00 1,520.00 - -
110 - - 88.70 127.00 230.00 381.00 - - - - -
120 - - 94.90 136.00 246.00 407.00 618.00 1,070.00 1,680.00 2,450.00 -
130 - - 101.00 145.00 262.00 433.00 - - - - -
140 - - 107.00 154.00 278.00 459.00 689.00 1,180.00 1,840.00 2,670.00 -
150 - - 113.00 163.00 294.00 485.00 725.00 1,230.00 1,920.00 2,780.00 3,860.00
160 - - 119.00 172.00 310.00 501.00 760.00 1,290.00 2,000.00 2,890.00 4,000.00
170 - - 125.00 181.00 326.00 527.00 - - - - -
180 - - 131.00 190.00 342.00 553.00 831.00 1,400.00 2,160.00 3,110.00 4,280.00
190 - - 137.00 199.00 358.00 579.00 - - - - -
200 - - 143.00 208.00 374.00 605.00 902.00 1,510.00 2,320.00 3,330.00 4.560.00
Add for
extra nut 2.32 4.82 10.90 15.90 30.80 60.30 103.00 216.00 369.00 610.00 924.00
per 1,000
Note : -
For mass of stainless steel bolts, multiply by the mass of black bolts by factor : 7881/7843
C/10
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 11
MASS (WEIGHT) OF STEEL CUP-HEADED RIVETS
Length Approximate mass in kilogrammes per 1,000
under Diameter of rivet
head (mm)
(mm) 10 12 16 20 22 24 27
25 21.50 31.90 - - - - -
30 24.60 36.30 71.00 125.00 - - -
35 27.70 40.80 78.80 137.00 - - -
40 30.80 45.20 86.70 149.00 186.00 238.00 -
45 33.80 49.70 94.60 162.00 201.00 255.00 -
50 36.90 54.10 103.00 174.00 216.00 273.00 -
55 40.00 58.50 110.00 186.00 231.00 291.00 -
60 43.10 63.00 118.00 199.00 246.00 309.00 386.00
65 46.20 67.40 126.00 211.00 261.00 326.00 408.00
70 49.30 71.80 134.00 223.00 276.00 344.00 431.00
75 52.30 76.30 142.00 236.00 291.00 362.00 453.00
80 55.40 80.70 150.00 248.00 306.00 380.00 476.00
90 - 89.60 166.00 273.00 335.00 415.00 521.00
100 - 98.50 181.00 297.00 365.00 451.00 566.00
110 - - 197.00 322.00 395.00 486.00 611.00
120 - - 213.00 347.00 425.00 522.00 656.00
130 - - - 371.00 455.00 557.00 700.00
140 - - - 396.00 485.00 593.00 745.00
150 - - - - 514.00 628.00 790.00
160 - - - - 554.00 664.00 835.00
170 - - - - 574.00 699.00 880.00
180 - - - - 604.00 735.00 925.00
190 - - - - - 770.00 970.00
200 - - - - - 806.00 1,050.00
Approx.
mass in kg
of 1,000 6.10 9.70 23.60 50.60 66.80 95.50 116.20
heads
Variation in
mass of
1,000 rivets 0.62 0.89 1.58 2.47 2.98 3.55 4.49
per mm of
length
C/11
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 12 TABLE 13
MASS (WEIGHT) OF ROLLED STEEL MASS (WEIGHT) OF ROLLED STEEL
EQUAL ANGLES UNEQUAL ANGLES
Source: BS EN10056-1:1999, Table 1 Source: BS EN10056-1:1999, Table 2
Designation Mass/unit Designation Mass/unit
Size Thickness length Size Thickness length
(mm) (mm) (kg/m) (mm) (mm) (kg/m)
20 x 20 3 0.88 30 x 20 3 1.12
25 x 25 3 1.12 30 x 20 4 1.46
25 x 25 4 1.45 40 x 20 4 1.77
30 x 30 3 1.36 40 x 25 4 1.93
30 x 30 4 1.78 45 x 30 4 2.25
35 x 35 4 2.09 50 x 30 5 2.96
40 x 40 4 2.42 60 x 30 5 3.36
40 x 40 5 2.97 60 x 40 5 3.76
45 x 45 4.5 3.06 60 x 40 6 4.46
50 x 50 4 3.06 65 x 50 5 4.35
50 x 50 5 3.77 70 x 50 6 5.41
50 x 50 6 4.47 75 x 50 6 5.65
60 x 60 5 4.57 75 x 50 8 7.39
60 x 60 6 5.42 80 x 40 6 5.41
60 x 60 8 7.09 80 x 40 8 7.07
65 x 65 7 6.83 80 x 60 7 7.36
70 x 70 6 6.38 100 x 50 6 6.84
70 x 70 7 7.38 100 x 50 8 8.97
75 x 75 6 6.85 100 x 65 7 8.77
75 x 75 8 8.99 100 x 65 8 9.94
80 x 80 8 9.63 100 x 65 10 12.30
80 x 80 10 11.90 100 x 75 8 10.60
90 x 90 7 9.61 100 x 75 10 13.00
90 x 90 8 10.90 100 x 75 12 15.40
90 x 90 9 12.20 120 x 80 8 12.20
90 x 90 10 13.40 120 x 80 10 15.00
100 x 100 8 12.20 120 x 80 12 17.80
100 x 100 10 15.00 125 x 75 8 12.20
100 x 100 12 17.80 125 x 75 10 15.00
120 x 120 10 18.20 125 x 75 12 17.80
120 x 120 12 21.60 135 x 65 8 12.20
130 x 130 12 23.60 135 x 65 10 15.00
150 x 150 10 23.00 150 x 75 9 15.40
150 x 150 12 27.30 150 x 75 10 17.00
150 x 150 15 33.80 150 x 75 12 20.20
160 x 160 15 36.20 150 x 75 15 24.80
180 x 180 16 43.50 150 x 90 10 18.20
180 x 180 18 48.60 150 x 90 12 21.60
200 x 200 16 48.50 150 x 90 15 26.60
200 x 200 18 54.30 150 x 100 10 19.00
200 x 200 20 59.90 150 x 100 12 22.50
200 x 200 24 71.10 200 x 100 10 23.00
250 x 250 28 104.00 200 x 100 12 27.30
250 x 250 35 128.00 200 x 100 15 33.75
200 x 150 12 32.00
200 x 150 15 39.60
C/12
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 14
MASS (WEIGHT) OF ROLLED STEEL UNIVERSAL BEAMS
Source: BS4-1:2005, Table 2
Mass per unit
Section designation length Depth Width
kg/m mm mm
914 x 419 x 388 388.0 921.0 420.5
914 x 419 x 343 343.3 911.8 418.5
914 x 305 x 289 289.1 926.6 307.7
914 x 305 x 253 253.4 918.4 305.5
914 x 305 x 224 224.2 910.4 304.1
914 x 305 x 201 200.9 903.0 303.3
838 x 292 x 226 226.5 850.9 293.8
838 x 292 x 194 193.8 840.7 292.4
838 x 292 x 176 175.9 834.9 291.7
762 x 267 x 197 196.8 769.8 268.0
762 x 267 x 173 173.0 762.2 266.7
762 x 267 x 147 146.9 754.0 265.2
762 x 267 x 134 133.9 750.0 264.4
686 x 254 x 170 170.2 692.9 255.8
686 x 254 x 152 152.4 687.5 254.5
686 x 254 x 140 140.1 683.5 253.7
686 x 254 x 125 125.2 677.9 253.0
610 x 305 x 238 238.1 635.8 311.4
610 x 305 x 179 179.0 620.2 307.1
610 x 305 x 149 149.1 612.4 304.8
610 x 229 x 140 139.9 617.2 230.2
610 x 229 x 125 125.1 612.2 229.0
610 x 229 x 113 113.0 607.6 228.2
610 x 229 x 101 101.2 602.6 227.6
533 x 210 x 122 122.0 544.5 211.9
533 x 210 x 109 109.0 539.5 210.8
533 x 210 x 101 101.0 536.7 210.0
533 x 210 x 92 92.1 533.1 209.3
533 x 210 x 82 82.2 528.3 208.8
457 x 191 x 98 98.3 467.2 192.8
457 x 191 x 89 89.3 463.4 191.9
457 x 191 x 82 82.0 460.0 191.3
457 x 191 x 74 74.3 457.0 190.4
457 x 191 x 67 67.1 453.4 189.9
457 x 152 x 82 82.1 465.8 155.3
457 x 152 x 74 74.2 462.0 154.4
457 x 152 x 67 67.2 458.0 153.8
457 x 152 x 60 59.8 454.6 152.9
457 x 152 x 52 52.3 449.8 152.4
C/13
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 14 (CONT'D)
MASS (WEIGHT) OF ROLLED STEEL UNIVERSAL BEAMS (CONT'D)
Source: BS4-1:2005, Table 2
Mass per unit
Section designation length Depth Width
kg/m mm mm
406 x 178 x 74 74.2 412.8 179.5
406 x 178 x 67 67.1 409.4 178.8
406 x 178 x 60 60.1 406.4 177.9
406 x 178 x 54 54.1 402.6 177.7
406 x 140 x 46 46.0 403.2 142.2
406 x 140 x 39 39.0 398.0 141.8
356 x 171 x 67 67.1 363.4 173.2
356 x 171 x 57 57.0 358.0 172.2
356 x 171 x 51 51.0 355.0 171.5
356 x 171 x 45 45.0 351.4 171.1
356 x 127 x 39 39.1 353.4 126.0
356 x 127 x 33 33.1 349.0 125.4
305 x 165 x 54 54.0 310.4 166.9
305 x 165 x 46 46.1 306.6 165.7
305 x 165 x 40 40.3 303.4 165.0
305 x 127 x 48 48.1 311.0 125.3
305 x 127 x 42 41.9 307.2 124.3
305 x 127 x 37 37.0 304.4 123.4
305 x 102 x 33 32.8 312.7 102.4
305 x 102 x 28 28.2 308.7 101.8
305 x 102 x 25 24.8 305.1 101.6
254 x 146 x 43 43.0 259.6 147.3
254 x 146 x 37 37.0 256.0 146.4
254 x 146 x 31 31.1 251.4 146.1
254 x 102 x 28 28.3 260.4 102.2
254 x 102 x 25 25.2 257.2 101.9
254 x 102 x 22 22.0 254.0 101.6
203 x 133 x 30 30.0 206.8 133.9
203 x 133 x 25 25.1 203.2 133.2
203 x 102 x 23 23.1 203.2 101.8
178 x 102 x 19 19.0 177.8 101.2
152 x 89 x 16 16.0 152.4 88.7
127 x 76 x 13 13.0 127.0 76.0
C/14
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 15
MASS (WEIGHT) OF ROLLED STEEL
UNIVERSAL COLUMNS
Source: BS4-1:2005, Table 3
Mass per unit
Section designation length Depth Width
kg/m mm mm
356 x 406 x 634 633.9 474.6 424.0
356 x 406 x 551 551.0 455.6 418.5
356 x 406 x 467 467.0 436.6 412.2
356 x 406 x 393 393.0 419.0 407.0
356 x 406 x 340 339.9 406.4 403.0
356 x 406 x 287 287.1 393.6 399.0
356 x 406 x 235 235.1 381.0 394.8
356 x 368 x 202 201.9 374.6 374.7
356 x 368 x 177 177.0 368.2 372.6
356 x 368 x 153 152.9 362.0 370.5
356 x 368 x 129 129.0 355.6 368.6
305 x 305 x 283 282.9 365.3 322.2
305 x 305 x 240 240.0 352.5 318.4
305 x 305 x 198 198.1 339.9 314.5
305 x 305 x 158 158.1 327.1 311.2
305 x 305 x 137 136.9 320.5 309.2
305 x 305 x 118 117.9 314.5 307.4
305 x 305 x 97 96.9 307.9 305.3
254 x 254 x 167 167.1 289.1 265.2
254 x 254 x 132 132.0 276.3 261.3
254 x 254 x 107 107.1 266.7 258.8
254 x 254 x 89 88.9 260.3 256.3
254 x 254 x 73 73.1 254.1 254.6
203 x 203 x 86 86.1 222.2 209.1
203 x 203 x 71 71.0 215.8 206.4
203 x 203 x 60 60.0 209.6 205.8
203 x 203 x 52 52.0 206.2 204.3
203 x 203 x 46 46.1 203.2 203.6
152 x 152 x 37 37.0 161.8 154.4
152 x 152 x 30 30.0 157.6 152.9
152 x 152 x 23 23.0 152.4 152.2
C/15
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 16
MASS (WEIGHT) OF ROLLED STEEL
UNIVERSAL BEARING PILES
Source: BS4-1:2005, Table 4
Mass per unit
Section designation length Depth Width
kg/m mm mm
356 x 368 x 174 173.9 361.4 378.5
356 x 368 x 152 152.0 356.4 376.0
356 x 368 x 133 133.0 352.0 373.8
356 x 368 x 109 108.9 346.4 371.0
305 x 305 x 223 222.9 337.9 325.7
305 x 305 x 186 186.0 328.3 320.9
305 x 305 x 149 149.1 318.5 316.0
305 x 305 x 126 126.1 312.3 312.9
305 x 305 x 110 110.0 307.9 310.7
305 x 305 x 95 94.9 303.7 308.7
305 x 305 x 88 88.0 301.7 307.8
305 x 305 x 79 78.9 299.3 306.4
254 x 254 x 85 85.1 254.3 260.4
254 x 254 x 71 71.0 249.7 258.0
254 x 254 x 63 63.0 247.1 256.6
203 x 203 x 54 53.9 204.0 207.7
203 x 203 x 45 44.9 200.2 205.9
C/16
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 17
MASS (WEIGHT) OF ROLLED STEEL
JOISTS WITH TAPER FLANGES
Source: BS4-1:2005, Table 5
Mass per unit
Section designation length Depth Width
kg/m mm mm
254 x 203 x 82 82.0 254.0 203.2
254 x 114 x 37 37.2 254.0 114.3
203 x 152 x 52 52.3 203.2 152.4
152 x 127 x 37 37.3 152.4 127.0
127 x 114 x 29 29.3 127.0 114.3
127 x 114 x 27 26.9 127.0 114.3
127 x 76 x 16 16.5 127.0 76.2
114 x 114 x 27 26.9 114.3 114.3
102 x 102 x 23 23.0 101.6 101.6
102 x 44 x 7 7.5 101.6 44.5
89 x 89 x 19 19.5 88.9 88.9
76 x 76 x 15 15.0 76.2 80.0
76 x 76 x 13 12.8 76.2 76.2
C/17
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 18
MASS (WEIGHT) OF ROLLED STEEL
STRUCTURAL TEES CUT FROM UNIVERSAL BEAMS
Source: BS 4-1:2005 Table 6
Mass per Cut from universal beams
Section designation unit length (See BS4-1:2005,Table 2) Width Depth
kg/m Section designation mm mm
305 x 457 x 127 126.7 914 x 305 x 253 305.5 459.1
305 x 457 x 112 112.1 914 x 305 x 224 304.1 455.1
305 x 457 x 101 100.4 914 x 305 x 201 303.3 451.4
292 x 419 x 113 113.2 838 x 292 x 226 293.8 425.4
292 x 419 x 97 96.9 838 x 292 x 194 292.4 420.3
292 x 419 x 88 87.9 838 x 292 x 176 291.7 417.4
267 x 381 x 99 98.3 762 x 267 x 197 268.0 384.8
267 x 381 x 87 86.5 762 x 267 x 173 266.7 381.0
267 x 381 x 74 73.4 762 x 267 x 147 265.2 376.9
254 x 343 x 85 85.1 686 x 254 x 170 255.8 346.4
254 x 343 x 76 76.2 686 x 254 x 152 254.5 343.7
254 x 343 x 70 70.0 686 x 254 x 140 253.7 341.7
254 x 343 x 63 62.6 686 x 254 x 125 253.0 338.9
305 x 305 x 119 119.0 610 x 305 x 238 311.4 317.8
305 x 305 x 90 89.5 610 x 305 x 179 307.1 310.0
305 x 305 x 75 74.6 610 x 305 x 149 304.8 306.1
229 x 305 x 70 69.9 610 x 229 x 140 230.2 308.5
229 x 305 x 63 62.5 610 x 229 x 125 229.0 306.0
229 x 305 x 57 56.5 610 x 229 x 113 228.2 303.7
229 x 305 x 51 50.6 610 x 229 x 101 227.6 301.2
210 x 267 x 61 61.0 533 x 210 x 122 211.9 272.2
210 x 267 x 55 54.5 533 x 210 x 109 210.8 269.7
210 x 267 x 51 50.5 533 x 210 x 101 210.0 268.3
210 x 267 x 46 46.0 533 x 210 x 92 209.3 266.5
210 x 267 x 41 41.1 533 x 210 x 82 208.8 264.1
191 x 229 x 49 49.1 457 x 191 x 98 192.8 233.5
191 x 229 x 45 44.6 457 x 191 x 89 191.9 231.6
191 x 229 x 41 41.0 457 x 191 x 82 191.3 229.9
191 x 229 x 37 37.1 457 x 191 x 74 190.4 228.4
191 x 229 x 34 33.5 457 x 191 x 67 189.9 226.6
C/18
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 18 (CONT'D)
MASS (WEIGHT) OF ROLLED STEEL
STRUCTURAL TEES CUT FROM UNIVERSAL BEAMS (CONT'D)
Source: BS 4-1:2005 Table 6
Mass per Cut from universal beams
Section designation unit length (See BS4-1:2005,Table 2) Width Depth
kg/m Section designation mm mm
152 x 229 x 41 41.0 457 x 152 x 82 155.3 232.8
152 x 229 x 37 37.1 457 x 152 x 74 154.4 230.9
152 x 229 x 34 33.6 457 x 152 x 67 153.8 228.9
152 x 229 x 30 29.9 457 x 152 x 60 152.9 227.2
152 x 229 x 26 26.1 457 x 152 x 52 152.4 224.8
178 x 203 x 37 37.1 406 x 178 x 74 179.5 206.3
178 x 203 x 34 33.5 406 x 178 x 67 178.8 204.6
178 x 203 x 30 30.0 406 x 178 x 60 177.9 203.1
178 x 203 x 27 27.0 406 x 178 x 54 177.7 201.2
140 x 203 x 23 23.0 406 x 140 x 46 142.2 201.5
140 x 203 x 20 19.5 406 x 140 x 39 141.8 198.9
171 x 178 x 34 33.5 356 x 171 x 67 173.2 181.6
171 x 178 x 29 28.5 356 x 171 x 57 172.2 178.9
171 x 178 x 26 25.5 356 x 171 x 51 171.5 177.4
171 x 178 x 23 22.5 356 x 171 x 45 171.1 175.6
127 x 178 x 20 19.5 356 x 127 x 39 126.0 176.6
127 x 178 x 17 16.5 356 x 127 x 33 125.4 174.4
165 x 152 x 27 27.0 305 x 165 x 54 166.9 155.1
165 x 152 x 23 23.0 305 x 165 x 46 165.7 153.2
165 x 152 x 20 20.1 305 x 165 x 40 165.0 151.6
127 x 152 x 24 24.0 305 x 127 x 48 125.3 155.4
127 x 152 x 21 20.9 305 x 127 x 42 124.3 153.5
127 x 152 x 19 18.5 305 x 127 x 37 123.4 152.1
102 x 152 x 17 16.4 305 x 102 x 33 102.4 156.3
102 x 152 x 14 14.1 305 x 102 x 28 101.8 154.3
102 x 152 x 13 12.4 305 x 102 x 25 101.6 152.5
146 x 127 x 22 21.5 254 x 146 x 43 147.3 129.7
146 x 127 x 19 18.5 254 x 146 x 37 146.4 127.9
146 x 127 x 16 15.5 254 x 146 x 31 146.1 125.6
102 x 127 x 14 14.1 254 x 102 x 28 102.2 130.1
102 x 127 x 13 12.6 254 x 102 x 25 101.9 128.5
102 x 127 x 11 11.0 254 x 102 x 22 101.6 126.9
133 x 102 x 15 15.0 203 x 133 x 30 133.9 103.3
133 x 102 x 13 12.5 203 x 133 x 25 133.2 101.5
C/19
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 19
MASS (WEIGHT) OF ROLLED STEEL
STRUCTURAL TEES CUT FROM UNIVERSAL COLUMNS
Source: BS 4-1:2005 Table 7
Mass per Cut from universal beams
Section designation unit length (See BS4-1:2005,Table 2) Width Depth
kg/m Section designation mm mm
406 x 178 x 118 117.5 356 x 406 x 235 394.8 190.4
368 x 178 x 101 100.9 356 x 368 x 202 374.7 187.2
368 x 178 x 89 88.5 356 x 368 x 177 372.6 184.0
368 x 178 x 77 76.4 356 x 368 x 153 370.5 180.9
368 x 178 x 65 64.5 356 x 368 x 129 368.6 177.7
305 x 152 x 79 79.0 305 x 305 x 158 311.2 163.5
305 x 152 x 69 68.4 305 x 305 x 137 309.2 160.2
305 x 152 x 59 58.9 305 x 305 x 118 307.4 157.2
305 x 152 x 49 48.4 305 x 305 x 97 305.3 153.9
254 x 127 x 66 66.0 254 x 254 x 132 261.3 138.1
254 x 127 x 54 53.5 254 x 254 x 107 258.8 133.3
254 x 127 x 45 44.4 254 x 254 x 89 256.3 130.1
254 x 127 x 37 36.5 254 x 254 x 73 254.6 127.0
203 x 102 x 43 43.0 203 x 203 x 86 209.1 111.0
203 x 102 x 36 35.5 203 x 203 x 71 206.4 107.8
203 x 102 x 30 30.0 203 x 203 x 60 205.8 104.7
203 x 102 x 26 26.0 203 x 203 x 52 204.3 103.0
203 x 102 x 23 23.0 203 x 203 x 46 203.6 101.5
152 x 76 x 19 18.5 152 x 152 x 37 154.4 80.8
152 x 76 x 15 15.0 152 x 152 x 30 152.9 78.7
152 x 76 x 12 11.5 152 x 152 x 23 152.2 76.1
C/20
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 20
MASS (WEIGHT) OF ROLLED STEEL
PARALLEL FLANGE CHANNELS
Source: BS 4-1:2005 Table 8
Mass per unit
Section designation length Depth Width
kg/m mm mm
430 x 100 x 64 64.4 430.0 100.0
380 x 100 x 54 54.0 380.0 100.0
300 x 100 x 46 45.5 300.0 100.0
300 x 90 x 41 41.4 300.0 90.0
260 x 90 x 35 34.8 260.0 90.0
260 x 75 x 28 27.6 260.0 75.0
230 x 90 x 32 32.2 230.0 90.0
230 x 75 x 26 25.7 230.0 75.0
200 x 90 x 30 29.7 200.0 90.0
200 x 75 x 23 23.4 200.0 75.0
180 x 90 x 26 26.1 180.0 90.0
180 x 75 x 20 20.3 180.0 75.0
150 x 90 x 24 23.9 150.0 90.0
150 x 75 x 18 17.9 150.0 75.0
125 x 65 x 15 14.8 125.0 65.0
100 x 50 x 10 10.2 100.0 50.0
TABLE 21
MASS (WEIGHT) OF ROLLED STEEL
EQUAL FLANGE TEES WITH RADIUSED ROOT AND TOES
Source: BS EN 10055:1996
Designation Mass Cross-section Height Width Thickness
kg/m cm2 mm mm mm
T30 1.77 2.26 30 30 4
T35 2.33 2.97 35 35 4.5
T40 2.96 3.77 40 40 5
T50 4.44 5.66 50 50 6
T60 6.23 7.94 60 60 7
T70 8.32 10.6 70 70 8
T80 10.7 13.6 80 80 9
T100 16.4 20.9 100 100 11
T120 23.2 29.6 120 120 13
T140 31.3 39.9 140 140 15
C/21
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 22
MASS (WEIGHT) OF ROLLED STEEL CIRCULAR HOLLOW SECTIONS
Source: BS-EN-10210-2-2006, Table B.1
Mass/unit Mass/unit Mass/unit
Diameter Thickness length Diameter Thickness length Diameter Thickness length
(mm) (mm) (kg/m) (mm) (mm) (kg/m) (mm) (mm) (kg/m)
21.30 2.30 1.08 177.80 5.00 21.30 355.60 6.30 54.30
2.60 1.20 6.30 26.60 8.00 68.60
3.20 1.43 8.00 33.50 10.00 85.20
26.90 2.30 1.40 10.00 41.40 12.50 106.00
2.60 1.56 12.50 51.00 14.20 120.00
3.20 1.87 193.70 5.00 23.30 16.00 134.00
33.70 2.60 1.99 6.30 29.10 20.00 166.00
3.20 2.41 8.00 36.60 25.00 204.00
4.00 2.93 10.00 45.30 406.40 6.30 62.20
42.40 2.60 2.55 12.50 55.90 8.00 78.60
3.20 3.09 14.20 62.90 10.00 97.80
4.00 3.79 16.00 70.10 12.50 121.00
48.30 2.60 2.93 219.10 5.00 26.40 14.20 137.00
3.20 3.56 6.30 33.10 16.00 154.00
4.00 4.37 8.00 41.60 20.00 191.00
5.00 5.34 10.00 51.60 25.00 235.00
60.30 2.60 3.70 12.50 63.70 30.00 278.00
3.20 4.51 14.20 71.80 40.00 361.00
4.00 5.55 16.00 80.10 457.00 6.30 70.00
5.00 6.82 20.00 98.20 8.00 88.60
76.10 2.60 4.71 244.50 5.00 29.50 10.00 110.00
3.20 5.75 6.30 37.00 12.50 137.00
4.00 7.11 8.00 46.70 14.20 155.00
5.00 8.77 10.00 57.80 16.00 174.00
88.90 3.20 6.76 12.50 71.50 20.00 216.00
4.00 8.38 14.20 80.60 25.00 266.00
5.00 10.30 16.00 90.20 30.00 316.00
6.30 12.80 20.00 110.70 40.00 411.00
101.60 3.20 7.77 25.00 135.00 508.00 6.30 77.90
4.00 9.63 273.00 5.00 33.00 8.00 98.60
5.00 11.90 6.30 41.40 10.00 123.00
6.30 14.80 8.00 52.30 12.50 153.00
8.00 18.50 10.00 64.90 14.20 173.00
10.00 22.60 12.50 80.30 16.00 194.00
114.30 3.20 8.77 14.20 90.60 20.00 241.00
4.00 10.90 16.00 101.00 25.00 298.00
5.00 13.50 20.00 125.00 30.00 354.00
6.30 16.80 25.00 153.00 40.00 462.00
8.00 21.00 323.90 5.00 39.30 50.00 565.00
10.00 25.70 6.30 49.30 610.00 6.30 93.80
139.70 4.00 13.40 8.00 62.30 8.00 119.00
5.00 16.60 10.00 77.40 10.00 148.00
6.30 20.70 12.50 96.00 12.50 184.00
8.00 26.00 14.20 108.50 14.20 209.00
10.00 32.00 16.00 121.00 16.00 234.00
12.50 39.20 20.00 150.00 20.00 291.00
168.30 4.00 16.20 25.00 184.00 25.00 361.00
5.00 20.10 30.00 429.00
6.30 25.20 40.00 562.00
8.00 31.60 50.00 691.00
10.00 39.00
12.50 48.00
C/22
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 23
MASS (WEIGHT) OF ROLLED STEEL SQUARE HOLLOW SECTIONS
Source: BS-EN-10210-2-2006, Table B.2
Mass/unit Mass/unit
Size Thickness length Size Thickness length
(mm) (mm) (kg/m) (mm) (mm) (kg/m)
40 x 40 2.60 3.00 160 x 160 5.00 24.10
3.20 3.61 6.30 30.10
4.00 4.39 8.00 37.60
5.00 5.28 10.00 46.30
50 x 50 2.60 3.81 12.50 56.60
3.20 4.62 14.20 63.30
4.00 5.64 16.00 70.20
5.00 6.85 180 x 180 5.00 27.30
6.30 8.31 6.30 34.00
60 x 60 2.60 4.63 8.00 42.70
3.20 5.62 10.00 52.50
4.00 6.90 12.50 64.40
5.00 8.42 14.20 72.20
6.30 10.30 16.00 80.20
8.00 12.50 200 x 200 5.00 30.40
70 x 70 3.20 6.63 6.30 38.00
4.00 8.15 8.00 47.70
5.00 9.99 10.00 58.80
6.30 12.30 12.50 72.30
8.00 15.00 14.20 81.10
80 x 80 3.20 7.63 16.00 90.30
4.00 9.41 220 x 220 6.30 41.90
5.00 11.60 8.00 52.70
6.30 14.20 10.00 65.10
8.00 17.50 12.50 80.10
90 x 90 4.00 10.70 14.20 90.10
5.00 13.10 16.00 100.00
6.30 16.20 250 x 250 6.30 47.90
8.00 20.10 8.00 60.30
100 x 100 4.00 11.90 10.00 74.50
5.00 14.70 12.50 91.90
6.30 18.20 14.20 103.00
8.00 22.60 16.00 115.00
10.00 27.40 260 x 260 6.30 49.90
120 x 120 5.00 17.80 8.00 62.80
6.30 22.20 10.00 77.70
8.00 27.60 12.50 95.80
10.00 33.70 14.20 108.00
12.50 40.90 16.00 120.00
140 x 140 5.00 21.00 300 x 300 6.30 57.80
6.30 26.10 8.00 72.80
8.00 32.60 10.00 90.20
10.00 40.00 12.50 112.00
12.50 48.70 14.20 126.00
150 x 150 5.00 22.60 16.00 141.00
6.30 28.10 350 x 350 8.00 85.40
8.00 35.10 10.00 106.00
10.00 43.10 12.50 131.00
12.50 52.70 14.20 148.00
14.20 58.90 16.00 166.00
16.00 65.20 400 x 400 10.00 122.00
12.50 151.00
14.20 170.00
16.00 191.00
20.00 235.00
C/23
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 24
MASS (WEIGHT) OF ROLLED STEEL RECTANGULAR HOLLOW SECTIONS
Source: BS-EN-10210-2-2006, Table B.3
Mass/unit Mass/unit
Size Thickness length Size Thickness length
(mm) (mm) (kg/m) (mm) (mm) (kg/m)
50 x 30 2.60 3.00 180 x 100 4.00 16.90
3.20 3.61 5.00 21.00
4.00 4.39 6.30 26.10
5.00 5.28 8.00 32.60
60 x 40 2.60 3.81 10.00 40.00
3.20 4.62 12.50 48.70
4.00 5.64 200 x 100 4.00 18.20
5.00 6.85 5.00 22.60
6.30 8.31 6.30 28.10
80 x 40 3.20 5.62 8.00 35.10
4.00 6.90 10.00 43.10
5.00 8.42 12.50 52.70
6.30 10.30 16.00 65.20
8.00 12.50 200 x 120 6.30 30.10
90 x 50 3.20 6.63 8.00 37.60
4.00 8.15 10.00 46.30
5.00 9.99 12.50 56.60
6.30 12.30 250 x 150 6.30 38.00
8.00 15.00 8.00 47.70
100 x 50 3.20 7.13 10.00 58.80
4.00 8.78 12.50 72.30
5.00 10.80 14.20 81.10
6.30 13.30 16.00 90.30
8.00 16.30 260 x 180 6.30 41.90
100 x 60 3.20 7.63 8.00 52.70
4.00 9.41 10.00 65.10
5.00 11.60 12.50 80.10
6.30 14.20 14.20 90.10
8.00 17.50 16.00 100.00
120 x 60 4.00 10.70 300 x 200 6.30 47.90
5.00 13.10 8.00 60.30
6.30 16.20 10.00 74.50
8.00 20.10 12.50 91.90
10.00 24.30 14.20 103.00
120 x 80 4.00 11.90 16.00 115.00
5.00 14.70 350 x 250 6.30 57.80
6.30 18.20 8.00 72.80
8.00 22.60 10.00 90.20
10.00 27.40 12.50 112.00
140 x 80 4.00 13.20 14.20 126.00
5.00 16.30 16.00 141.00
6.30 20.20 400 x 200 8.00 72.80
8.00 25.10 10.00 90.20
10.00 30.60 12.50 112.00
150 x 100 4.00 15.10 14.20 126.00
5.00 18.60 16.00 141.00
6.30 23.10 450 x 250 8.00 85.40
8.00 28.90 10.00 106.00
10.00 35.30 12.50 131.00
12.50 42.80 14.20 148.00
160 x 80 4.00 14.40 16.00 166.00
5.00 17.80 500 x 300 10.00 122.00
6.30 22.20 12.50 151.00
8.00 27.60 14.20 170.00
10.00 33.70 16.00 191.00
12.50 40.90 20.00 235.00
C/24
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 25
MASS (WEIGHT) OF SOLID
ALUMINIUM ROUND BARS
Mass/unit Mass/unit Mass/unit
Diameter length Diameter length Diameter length
(mm) (kg/m) (mm) (kg/m) (mm) (kg/m)
5.00 0.054 17.45 0.649 35.99 2.760
6.35 0.086 19.05 0.772 36.50 2.838
6.73 0.097 19.84 0.838 38.10 3.092
7.14 0.109 20.62 0.906 44.45 4.210
7.92 0.134 21.44 0.979 46.99 4.656
8.74 0.162 22.22 1.052 47.62 4.832
9.14 0.178 23.80 1.207 50.80 5.497
9.52 0.193 25.40 1.375 52.98 6.207
10.31 0.226 26.97 1.552 57.15 6.959
11.10 0.263 28.19 1.694 60.32 7.753
11.89 0.301 28.58 1.740 63.50 8.590
12.70 0.344 30.15 1.936 69.85 10.387
14.27 0.434 31.75 2.147 76.20 12.359
15.06 0.484 33.32 2.366
15.87 0.537 34.92 2.598
TABLE 26
MASS (WEIGHT) OF SOLID
ALUMINIUM SQUARE BARS
Mass/unit Mass/unit Mass/unit
Size length Size length Size length
(mm) (kg/m) (mm) (kg/m) (mm) (kg/m)
6.35 0.109 12.19 0.403 19.05 0.984
7.92 0.171 12.70 0.438 22.22 1.341
9.52 0.244 15.88 0.682 25.40 1.750
C/25
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 27
MASS (WEIGHT) OF SOLID
ALUMINIUM FLATS
Mass/unit Mass/unit Mass/unit
Size length Size length Size length
(mm) (kg/m) (mm) (kg/m) (mm) (kg/m)
6.35 x 3.18 0.054 25.40 x 19.05 1.312 63.50 x 3.18 0.546
9.52 x 2.36 0.061 25.58 x 3.18 0.242 63.50 x 6.35 1.094
9.52 x 3.18 0.082 25.58 x 6.35 0.491 63.50 x 9.52 1.644
9.52 x 6.35 0.016 31.75 x 1.60 0.138 63.50 x 12.70 2.188
10.10 x 2.01 0.055 31.75 x 3.18 0.274 63.50 x 19.05 3.281
11.10 x 3.96 0.118 31.75 x 4.75 0.409 69.85 x 3.18 0.601
11.10 x 6.35 0.190 31.75 x 6.35 0.546 69.85 x 4.75 0.952
12.70 x 1.57 0.054 31.75 x 9.52 0.820 69.85 x 6.35 1.204
12.70 x 2.36 0.080 31.75 x 12.70 1.089 69.85 x 9.52 1.804
12.70 x 3.18 0.109 34.92 x 3.18 0.301 69.85 x 12.70 2.406
12.70 x 4.75 0.164 34.92 x 6.35 0.582 69.85 x 15.88 3.008
12.70 x 6.35 0.219 34.92 x 9.52 0.903 76.20 x 1.57 0.324
14.00 x 3.00 0.113 34.92 x 12.70 1.204 76.20 x 3.18 0.658
15.88 x 1.57 0.067 38.10 x 1.57 0.162 76.20 x 6.35 1.312
15.88 x 2.36 0.101 38.10 x 2.36 0.244 76.20 x 9.52 1.969
15.88 x 3.18 0.137 38.10 x 3.18 0.327 76.20 x 12.70 2.619
15.88 x 4.75 0.204 38.10 x 4.75 0.490 76.20 x 19.05 3.938
15.88 x 6.35 0.272 38.10 x 6.35 0.656 82.55 x 3.18 0.665
15.88 x 9.52 0.409 38.10 x 9.52 0.982 82.55 x 6.35 1.423
17.45 x 3.18 0.150 38.10 x 12.70 1.310 82.55 x 12.70 2.844
17.45 x 4.75 0.223 38.10 x 15.88 1.640 88.90 x 3.18 0.765
17.45 x 6.35 0.301 38.10 x 19.05 1.964 88.90 x 6.35 1.531
18.24 x 8.74 0.427 38.10 x 25.40 2.625 88.90 x 9.52 2.296
18.64 x 4.37 0.219 41.28 x 3.18 0.356 88.90 x 12.70 3.063
19.05 x 1.57 0.082 41.28 x 6.35 0.711 95.25 x 3.18 0.821
19.05 x 2.36 0.122 41.28 x 9.52 1.065 95.25 x 6.35 1.641
19.05 x 3.18 0.164 44.45 x 3.18 0.382 95.25 x 9.52 2.461
19.05 x 4.75 0.246 44.45 x 6.35 0.765 95.25 x 12.70 3.281
19.05 x 6.35 0.329 44.45 x 9.52 1.149 101.60 x 3.18 0.875
19.05 x 9.07 0.491 44.45 x 12.70 1.531 101.60 x 6.35 1.750
19.99 x 3.00 0.162 50.80 x 1.57 0.217 101.60 x 9.52 2.619
22.22 x 3.18 0.192 50.80 x 3.18 0.438 101.60 x 31.75 8.750
22.22 x 6.35 0.381 50.80 x 4.75 0.655 114.30 x 2.03 0.629
22.22 x 9.52 0.574 50.80 x 6.35 0.875 114.30 x 6.35 1.969
23.80 x 3.18 0.205 50.80 x 9.52 1.312 114.30 x 9.52 2.952
23.80 x 6.35 0.409 50.80 x 12.70 1.750 114.30 x 12.70 3.929
23.80 x 9.52 0.615 50.80 x 15.88 2.188 127.00 x 6.35 2.188
24.99 x 8.00 0.543 57.15 x 2.29 0.354 127.00 x 9.52 3.289
25.40 x 1.57 0.109 57.15 x 3.18 0.492 127.00 x 12.70 4.375
25.40 x 2.36 0.162 57.15 x 6.35 0.984 127.00 x 19.05 6.563
25.40 x 3.18 0.219 57.15 x 9.52 1.476 133.35 x 6.35 2.274
25.40 x 4.75 0.327 57.15 x 12.70 1.969 139.70 x 6.35 2.406
25.40 x 6.35 0.438 57.15 x 19.05 2.952 146.05 x 6.35 2.490
25.40 x 7.92 0.546 59.44 x 3.56 0.573 152.40 x 3.18 1.302
25.40 x 9.52 0.656 63.37 x 19.30 3.319 152.40 x 6.35 2.625
25.40 x 12.70 0.875 63.50 x 1.57 0.271 152.40 x 9.52 3.938
25.40 x 15.88 1.094 63.50 x 2.36 0.406
C/26
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 28 TABLE 29
MASS (WEIGHT) OF MASS (WEIGHT) OF
ALUMINIUM EQUAL ANGLES ALUMINIUM UNEQUAL ANGLES
Size Thickness Mass/unit length Size Thickness Mass/unit length
(mm) (mm) (kg/m) (mm) (mm) (kg/m)
9.52 1.19 0.058 12.70 x 6.35 3.18 0.137
9.52 1.57 0.076 15.88 x 12.70 3.18 0.219
12.70 1.02 0.067 19.05 x 6.35 3.18 0.190
12.70 1.19 0.079 19.05 x 9.52 3.18 0.219
12.70 1.57 0.101 19.05 x 12.70 1.19 0.100
12.70 2.36 0.147 19.05 x 12.70 1.57 0.129
12.70 3.18 0.192 19.05 x 12.70 3.18 0.247
15.88 1.57 0.129 22.22 x 12.70 1.19 0.109
15.88 3.18 0.244 22.22 x 12.70 3.18 0.274
15.88 4.75 0.351 25.40 x 12.70 1.19 0.119
19.05 1.19 0.119 25.40 x 12.70 1.57 0.158
19.05 1.57 0.156 25.40 x 12.70 2.36 0.231
19.05 2.39 0.231 25.40 x 12.70 3.18 0.301
19.05 3.18 0.301 25.40 x 19.05 3.18 0.356
20.22 1.17 0.124 31.75 x 12.70 1.19 0.140
22.22 3.18 0.356 31.75 x 12.70 1.57 0.183
25.40 1.19 0.161 31.75 x 12.70 2.36 0.272
25.40 1.57 0.210 31.75 x 12.70 3.18 0.186
25.40 2.36 0.308 31.75 x 19.05 2.08 0.275
25.40 3.18 0.409 31.75 x 19.05 3.18 0.409
25.40 6.35 0.766 31.75 x 25.40 3.18 0.464
28.58 3.18 0.464 38.10 x 11.10 1.57 0.204
31.75 1.57 0.266 38.10 x 12.70 1.19 0.161
31.75 3.18 0.521 38.10 x 12.70 1.27 0.170
31.75 6.35 0.967 38.10 x 12.70 1.57 0.210
34.92 3.18 0.574 38.10 x 12.70 2.36 0.311
38.10 1.57 0.318 38.10 x 12.70 3.18 0.409
38.10 3.18 0.629 38.10 x 19.05 2.36 0.354
38.10 4.75 0.918 38.10 x 19.05 3.18 0.464
38.10 6.35 1.202 38.10 x 25.40 1.57 0.265
44.45 3.18 0.738 38.10 x 25.40 2.36 0.391
44.45 6.35 1.421 38.10 x 25.40 3.18 0.521
50.00 3.00 0.789 38.10 x 31.75 3.18 0.574
50.00 5.00 1.290 44.45 x 12.70 1.57 0.234
50.80 1.60 0.432 44.45 x 12.70 3.18 0.464
50.80 2.36 0.635 44.45 x 25.40 1.57 0.292
50.80 3.18 0.845 44.45 x 25.40 2.36 0.432
50.80 4.75 1.244 44.45 x 25.40 3.18 0.574
50.80 6.35 1.640 47.72 x 15.88 3.18 0.516
63.50 3.18 1.066 50.80 x 12.70 1.19 0.202
63.50 6.35 2.068 50.80 x 12.70 1.57 0.265
63.50 7.92 2.564 50.80 x 12.70 2.36 0.391
76.20 6.35 2.502 50.80 x 12.70 3.18 0.519
80.01 5.99 2.504 50.80 x 19.05 3.18 0.574
80.01 10.01 4.073 50.80 x 25.40 1.57 0.318
50.80 x 25.40 3.18 0.626
50.80 x 38.10 3.18 0.729
63.50 x 12.70 2.54 0.507
63.50 x 25.40 3.18 0.740
63.50 x 38.10 6.35 1.637
76.20 x 12.70 1.60 0.379
76.20 x 12.70 2.36 0.555
76.20 x 25.40 3.18 0.847
76.20 x 31.75 3.18 0.903
88.90 x 25.40 6.35 1.845
88.90 x 44.45 3.18 1.122
C/27
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 30
MASS (WEIGHT) OF ALUMINIUM CHANNELS
Mass/unit Mass/unit
Size Thickness length Size Thickness length
(mm) (mm) (kg/m) (mm) (mm) (kg/m)
7.14 x 5.16 1.19 0.049 34.92 x 6.35 1.57 0.190
7.39 x 5.99 1.29 0.051 38.10 x 12.70 1.57 0.257
7.77 x 5.54 1.52 0.065 38.10 x 12.70 2.36 0.376
7.92 x 12.70 1.57 0.129 38.10 x 19.05 3.18 0.602
9.53 x 9.53 1.19 0.085 38.10 x 25.40 1.57 0.366
9.53 x 9.53 1.57 0.109 38.10 x 38.10 3.18 0.930
11,94 x 15.24 2.36 0.239 38.10 x 69.85 1.78 0.841
12.70 x 9.53 1.57 0.122 44.45 x 15.88 3.18 0.602
12.70 x 9.53 3.18 0.219 44.45 x 25.40 3.18 0.766
12.70 x 12.70 1.57 0.149 50.80 x 12.70 1.14 0.229
12.70 x 12.70 2.36 0.214 50.80 x 12.70 1.57 0.311
12.70 x 19.05 1.57 0.202 50.80 x 12.70 2.36 0.457
12.70 x 19.05 2.36 0.293 50.80 x 12.70 3.18 0.601
12.70 x 19.05 3.18 0.384 50.80 x 25.40 1.57 0.419
14.23 x 4.75 2.36 0.122 50.80 x 25.40 2.03 0.537
15.87 x 3.96 1.57 0.087 50.80 x 25.40 3.18 0.812
15.88 x 12.70 3.18 0.301 50.80 x 25.40 9.50 1.186
15.88 x 15.88 1.57 0.190 50.80 x 50.80 3.18 1.257
15.88 x 15.88 1.60 0.192 53.97 x 6.53 1.57 0.271
15.88 x 25.40 3.18 0.519 57.15 x 12.70 1.57 0.445
17.45 x 11.10 3.18 0.286 63.50 x 12.70 2.36 0.580
19.05 x 9.53 1.57 0.149 63.50 x 15.88 3.18 0.766
19.05 x 9.53 2.54 0.228 63.50 x 22.22 3.18 0.875
19.05 x 12.70 1.19 0.137 63.50 x 38.10 3.18 1.147
19.05 x 12.70 2.54 0.271 70.00 x 25.00 3.00 0.928
19.05 x 19.05 1.57 0.231 76.20 x 12.70 1.60 0.427
19.05 x 19.05 3.18 0.437 76.20 x 12.70 2.36 0.620
19.05 x 38.10 3.18 0.763 76.20 x 12.70 3.18 0.818
22.22 x 12.79 1.19 0.147 76.20 x 25.40 2.36 0.783
25.40 x 12.70 1.57 0.202 76.20 x 25.40 3.18 1.040
25.40 x 19.05 2.36 0.379 76.20 x 38.10 2.54 1.015
25.40 x 25.40 3.18 0.601 76.20 x 44.45 2.36 1.028
25.40 x 38.10 3.18 0.818 95.25 x 25.40 3.18 2.689
31.75 x 12.70 1.19 0.180 100.00 x 20.00 1.75 0.649
31.75 x 12.70 3.40 0.466 101.60 x 25.40 2.03 0.817
31.75 x 25.40 2.36 0.498 101.60 x 38.10 3.18 1.473
31.75 x 25.40 3.18 0.656 127.00 x 69.85 3.18 2.232
31.75 x 41.28 3.18 0.930
C/28
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 31
MASS (WEIGHT) OF ALUMINIUM TEE SECTIONS
Mass/unit
Size Thickness length
(mm) (mm) (kg/m)
12.70 x 12.70 3.18 0.190
15.88 x 15.88 3.18 0.245
19.05 x 19.05 1.57 0.156
19.05 x 19.05 3.18 0.305
19.05 x 31.75 3.18 0.409
25.40 x 19.05 1.57 0.180
25.40 x 25.40 1.57 0.211
25.40 x 25.40 3.18 0.409
25.40 x 30.15 1.57 0.231
25.40 x 31.75 3.18 0.466
25.40 x 38.10 1.57 0.262
25.40 x 38.10 3.18 0.519
28.58 x 38.10 3.18 0.549
31.75 x 19.05 2.08 0.275
31.75 x 25.40 3.18 0.466
38.10 x 25.40 2.39 0.396
38.10 x 25.40 3.96 0.641
38.10 x 38.10 3.18 0.629
38.10 x 38.10 6.35 1.201
50.80 x 19.05 3.18 0.574
50.80 x 25.40 3.18 0.629
50.80 x 38.10 3.18 0.738
50.80 x 50.80 4.75 1.247
C/29
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 32
MASS (WEIGHT) OF ALUMINIUM ROUND HOLLOW TUBES
Mass/unit Mass/unit Mass/unit
Size Thickness length Size Thickness length Size Thickness length
(mm) (mm) (kg/m) (mm) (mm) (kg/m) (mm) (mm) (kg/m)
10.31 1.27 0.098 31.75 2.03 0.515 47.75 6.60 2.292
12.29 1.45 0.134 31.75 3.18 0.774 48.21 5.61 2.037
12.70 1.22 0.122 31.75 4.75 1.085 48.26 1.91 0.753
12.70 1.57 0.149 31.75 6.35 1.360 49.99 4.04 4.750
13.34 1.57 0.159 32.99 1.52 0.405 50.50 13.23 4.204
15.65 1.42 0.173 33.02 6.35 1.429 50.80 1.57 0.661
15.88 1.57 0.235 33.35 3.18 0.820 50.80 3.18 1.289
15.88 2.03 0.239 34.93 1.47 0.420 50.80 5.38 2.067
18.01 1.50 0.211 34.93 2.79 0.790 50.80 7.92 2.869
19.05 1.24 0.180 34.93 3.18 0.851 50.80 9.39 3.286
19.05 1.57 0.235 34.93 4.75 1.222 50.80 13.41 4.229
19.05 2.03 0.295 34.93 4.95 0.689 50.80 14.30 4.445
19.05 2.36 0.336 34.93 6.35 1.531 50.93 4.00 1.583
19.05 3.18 0.429 34.93 7.14 1.692 50.93 7.49 2.769
19.99 4.50 0.594 35.00 1.50 0.466 51.00 11.99 3.985
20.00 1.50 0.236 38.10 3.25 0.966 51.00 16.76 4.686
21.49 3.51 0.552 38.10 1.57 0.490 51.56 6.09 2.336
22.23 1.57 0.277 38.10 2.36 0.719 51.56 8.31 3.034
22.23 2.03 0.349 38.10 2.64 0.798 51.99 10.00 3.542
23.01 1.50 0.277 38.10 3.18 0.945 51.99 11.99 4.048
23.01 5.00 0.768 38.10 5.08 1.430 52.50 1.50 0.652
23.50 1.50 0.281 38.10 6.17 1.677 52.50 16.00 4.973
23.50 3.81 0.678 38.10 8.74 2.186 52.98 15.49 4.947
24.13 3.18 0.567 38.99 7.98 2.089 53.26 2.03 0.878
25.40 1.24 0.256 39.37 9.37 2.378 53.98 6.99 3.542
25.40 1.91 0.381 39.67 6.35 1.802 54.00 2.24 0.991
25.40 2.03 0.405 40.13 9.07 2.400 54.00 2.26 0.991
25.40 2.36 0.464 41.28 4.70 1.461 54.48 2.59 1.140
25.40 3.18 0.601 41.28 5.94 1.793 54.51 2.29 1.018
25.91 1.27 0.266 41.28 10.34 2.723 55.88 16.51 5.540
26.19 1.09 0.234 42.85 1.57 0.558 57.15 3.86 1.801
26.49 3.25 0.643 42.93 6.93 2.124 57.51 1.50 0.716
26.97 2.39 0.493 43.99 8.00 2.429 58.93 11.48 4.642
26.97 5.94 1.052 44.45 1.57 0.579 58.98 11.99 7.405
27.00 4.90 0.905 44.45 3.18 1.115 60.96 5.84 2.716
27.20 1.60 0.350 44.45 4.06 1.399 60.96 9.83 4.239
28.58 1.47 0.339 44.45 6.02 1.610 60.96 8.26 3.670
28.58 2.49 0.554 44.45 6.73 2.164 61.11 2.36 1.183
29.01 8.99 1.534 44.45 8.74 2.633 63.50 1.60 0.844
29.06 4.57 0.954 44.45 14.22 3.664 63.50 3.13 0.143
29.11 5.41 1.082 44.45 15.88 3.866 63.50 6.99 3.329
29.11 7.01 1.305 45.24 1.98 0.731 76.20 2.36 1.487
29.36 6.35 1.246 45.72 2.03 0.749 76.20 4.76 2.897
30.99 9.00 1.686 45.72 2.34 0.865 76.20 20.32 9.676
31.24 2.74 0.664 47.63 3.66 1.371 101.60 6.35 5.155
31.75 1.47 0.379 47.63 4.75 1.722 127.00 12.70 12.369
31.75 1.57 0.408 47.63 7.32 2.509
C/30
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 33 TABLE 34
MASS (WEIGHT) OF ALUMINIUM MASS (WEIGHT) OF ALUMINIUM
SQUARE HOLLOW SECTIONS RECTANGULAR HOLLOW SECTIONS
Mass/unit Mass/unit
Size Thickness length Size Thickness length
(mm) (mm) (kg/m) (mm) (mm) (kg/m)
9.54 1.57 0.135 12.70 x 9.85 1.59 0.165
12.88 1.20 0.150 25.40 x 12.70 1.60 0.302
12.70 1.57 0.244 25.40 x 12.70 1.20 0.232
15.88 1.20 0.191 31.75 x 19.05 2.36 0.591
18.24 3.18 0.519 36.10 x 19.05 2.36 0.673
19.05 1.20 0.232 38.10 x 25.40 1.40 0.461
19.05 1.57 0.296 38.10 x 25.40 2.03 0.655
19.05 2.36 0.428 38.10 x 25.40 2.54 0.811
25.40 1.40 0.364 47.63 x 23.80 3.18 1.122
25.40 1.60 0.415 50.00 x 40.00 2.00 0.933
25.40 2.03 0.515 50.80 x 25.40 1.40 0.557
25.40 2.36 0.589 50.80 x 25.40 1.57 0.624
25.40 3.18 0.765 50.80 x 25.40 2.03 0.795
30.00 2.00 0.604 50.80 x 25.40 2.36 0.917
31.75 2.03 0.655 50.80 x 38.10 1.60 0.744
38.10 1.57 0.623 50.80 x 38.10 2.03 0.935
38.10 2.03 0.795 50.80 x 38.10 2.36 1.016
38.10 3.18 1.205 63.50 x 31.75 2.36 1.161
44.45 2.39 1.091 63.50 x 38.10 2.54 1.327
46.62 3.18 1.531 63.50 x 38.10 3.18 1.652
50.00 2.00 1.044 69.85 x 31.75 3.18 1.641
50.80 2.03 1.074 76.20 x 25.40 1.80 0.957
50.80 2.36 1.241 76.20 x 25.40 2.36 1.241
63.50 3.18 2.056 76.20 x 38.10 3.18 1.860
76.20 3.18 2.516 76.20 x 44.45 1.80 1.143
80.00 2.49 2.092 76.20 x 44.45 2.36 1.439
76.20 x 44.45 3.18 1.958
76.20 x 50.80 2.36 1.567
76.20 x 50.80 3.18 2.076
80.00 x 20.00 2.00 1.045
80.00 x 40.00 2.00 1.258
80.00 x 50.00 2.50 1.688
82.55 x 28.58 2.36 1.360
100.00 x 40.00 2.50 1.823
101.60 x 25.40 1.80 1.205
101.60 x 25.40 2.03 1.354
101.60 x 25.40 2.36 1.567
101.60 x 38.10 3.18 2.292
101.60 x 44.45 1.80 1.391
101.60 x 44.45 1.98 1.529
101.60 x 44.45 2.36 1.813
101.60 x 44.45 3.18 2.403
101.60 x 60.33 2.36 2.015
127.00 x 25.40 2.36 1.894
C/31
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 35 TABLE 36
MASS (WEIGHT) OF STAINLESS MASS (WEIGHT) OF STAINLESS
STEEL FLAT BARS STEEL ANGLES
Mass/unit Mass/unit
Size Thickness length Size Thickness length
(mm) (mm) (kg/m) (mm) (mm) (kg/m)
19.05 3.00 0.450 9.52 x 9.52 1.00 0.142
19.05 6.00 0.901 12.70 x 12.70 1.00 0.192
25.40 3.00 0.601 19.05 x 19.05 1.00 0.292
25.40 6.00 1.201 25.40 x 25.40 1.00 0.392
31.80 3.00 0.751 12.70 x 25.40 1.00 0.293
31.80 3.60 0.901 38.10 x 38.10 3.00 1.731
31.80 6.00 1.802
50.80 6.00 2.402
TABLE 37 TABLE 38
MASS (WEIGHT) OF STAINLESS MASS (WEIGHT) OF STAINLESS
STEEL CHANNELS STEEL ROUND TUBES
Mass/unit Mass/unit
Size Thickness length Size Thickness length
(mm) (mm) (kg/m) (mm) (mm) (kg/m)
9.52 x 9.52 0.50 0.109 9.52 0.80 0.173
9.52 x 9.52 0.80 0.170 12.70 1.00 0.290
12.70 x 12.70 0.50 0.146 15.87 0.80 0.298
12.70 x 12.70 0.80 0.230 19.05 1.00 0.447
12.70 x 19.05 0.50 0.171 19.05 1.20 0.530
12.70 x 25.40 0.50 0.196 25.40 1.00 0.604
12.70 x 38.10 0.50 0.246 25.40 1.50 0.888
12.70 x 50.80 0.50 0.296 31.75 1.00 0.761
12.70 x 76.20 0.50 0.396 31.75 1.50 1.123
12.70 x 101.60 0.80 0.791 38.10 1.50 1.359
44.45 1.50 1.595
50.80 1.50 1.831
60.32 1.50 2.184
TABLE 39 TABLE 40
MASS (WEIGHT) OF STAINLESS MASS (WEIGHT) OF STAINLESS STEEL
STEEL SQUARE HOLLOW SECTIONS RECTANGULAR HOLLOW SECTIONS
Mass/unit Mass/unit
Size Thickness length Size Thickness length
(mm) (mm) (kg/m) (mm) (mm) (kg/m)
19.05 1.00 0.569 12.70 x 25.40 1.00 0.569
25.40 1.00 0.769 15.87 x 31.75 1.20 0.855
12.70 1.00 0.369 25.40 x 38.10 1.20 1.156
19.05 1.00 0.569 25.40 x 50.80 1.20 1.396
25.40 1.20 0.915 38.10 x 76.20 1.50 2.631
31.75 1.20 1.156 44.45 x 76.20 1.50 2.782
38.10 1.20 1.396 50.80 x 101.60 2.00 4.678
50.80 1.20 1.876
C/32
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 41
STANDARD BRC FABRICS
SQUARE MESHES
BS 4483 Main wire Cross wire Cross Sectional Area Mass
BRC or SS-32 per unit
reference reference Size Spacing Size Spacing Main Cross area
number number (mm) (mm) (mm) (mm) mm2/m mm2/m (kg/m)
D 13 - 13.00 100.00 13.00 100.00 1,327.00 1,327.00 20.84
D 12 - 12.00 100.00 12.00 100.00 1,131.00 1,131.00 17.76
D 11 - 11.00 100.00 11.00 100.00 950.00 950.00 14.92
D 10 - 10.00 100.00 10.00 100.00 785.00 785.00 12.32
D9 - 9.00 100.00 9.00 100.00 636.00 636.00 9.98
D8 - 8.00 100.00 8.00 100.00 503.00 503.00 7.90
D7 - 7.00 100.00 7.00 100.00 385.00 385.00 6.04
D6 - 6.00 100.00 6.00 100.00 283.00 283.00 4.44
D5 - 5.00 100.00 5.00 100.00 196.00 196.00 3.08
D4 - 4.00 100.00 4.00 100.00 126.00 126.00 1.98
A 13 - 13.00 200.00 13.00 200.00 664.00 664.00 10.42
A 12 - 12.00 200.00 12.00 200.00 566.00 566.00 8.88
A 11 - 11.00 200.00 11.00 200.00 475.00 475.00 7.46
A 10 A 393 10.00 200.00 10.00 200.00 393.00 393.00 6.16
A9 - 9.00 200.00 9.00 200.00 318.00 318.00 4.99
A8 A 252 8.00 200.00 8.00 200.00 252.00 252.00 3.95
A7 A 193 7.00 200.00 7.00 200.00 193.00 193.00 3.02
A6 A 142 6.00 200.00 6.00 200.00 142.00 142.00 2.22
A5 A 98 5.00 200.00 5.00 200.00 98.00 98.00 1.54
E 13 - 13.00 150.00 13.00 150.00 885.00 885.00 13.89
E 12 - 12.00 150.00 12.00 150.00 754.00 754.00 11.84
E 11 - 11.00 150.00 11.00 150.00 634.00 634.00 9.95
E 10 - 10.00 150.00 10.00 150.00 524.00 524.00 8.23
E9 - 9.00 150.00 9.00 150.00 424.00 424.00 6.67
E8 - 8.00 150.00 8.00 150.00 335.00 335.00 5.27
N6 - 6.00 100.00 6.00 75.00 283.00 377.00 5.18
TABLE 42
STANDARD BRC FABRICS
RECTANGULAR MESHES
BS 4483 Main wire Cross wire Cross Sectional Area Mass
BRC or SS-32 per unit
reference reference Size Spacing Size Spacing Main Cross area
number number (mm) (mm) (mm) (mm) mm2/m mm2/m (kg/m)
B 13 - 13.00 100.00 10.00 200.00 1,327.00 393.00 13.50
B 12 B 1131 12.00 100.00 8.00 200.00 1,131.00 252.00 10.90
B 11 - 11.00 100.00 8.00 200.00 950.00 252.00 9.43
B 10 B 785 10.00 100.00 8.00 200.00 785.00 252.00 8.14
B9 - 9.00 100.00 8.00 200.00 636.00 252.00 6.97
B 8A - 8.00 150.00 7.00 200.00 335.00 193.00 4.14
B8 B 503 8.00 100.00 8.00 200.00 503.00 252.00 5.93
B7 B 385 7.00 100.00 7.00 200.00 385.00 193.00 4.53
B6 B 283 6.00 100.00 7.00 200.00 283.00 193.00 3.73
B5 B 196 5.00 100.00 7.00 200.00 196.00 193.00 3.05
C 10 C 785 10.00 100.00 6.00 400.00 785.00 70.80 6.72
C9 C 636 9.00 100.00 6.00 400.00 636.00 70.80 5.55
C8 C 503 8.00 100.00 5.00 400.00 503.00 49.00 4.34
C7 C 385 7.00 100.00 5.00 400.00 385.00 49.00 3.41
C6 C 283 6.00 100.00 5.00 400.00 283.00 49.00 2.61
C/33
ANNEX 'C' - TABLES OF METAL WEIGHTS, ETC.
TABLE 43
MASS (WEIGHT) OF
STEEL SHEET PILES
Mass per Mass per
Type pile wall width
(kg/m) (kg/m)
FSP-IA 35.50 88.80
FSP-II 48.00 120.00
FSP-IIA 43.20 108.00
FSP-III 60.00 150.00
FSP-IIIA 58.40 146.00
FSP-IIIL 68.00 138.00
FSP-IV 76.10 190.00
FSP-IVA 74.00 185.00
FSP-IVL 87.50 175.00
FSP-VL 105.00 210.00
FSP-VIL 120.00 240.00
YSP-I 36.50 91.20
YSP-U5 35.50 88.80
YSP-II 48.00 120.00
YSP-U9 43.20 108.00
YSP-III 60.00 150.00
YSP-U15 58.40 146.00
YSP-IV 76.10 190.00
YSP-U23 74.00 185.00
YSP-V 105.00 250.00
TABLE 44
MASS (WEIGHT) OF STEEL CHEQUER PLATE
Thickness Projected thickness Approximate
on plain (inclusive of weight
mm raised pattern) kg/m
(t) mm
3.0 4.5 28.7
4.5 6.0 40.5
6.0 7.5 52.2
8.0 9.5 67.9
10.0 11.5 83.6
12.5 14.0 103.1
C/34
