Scribd
Upload
45 views

Output Rating Operating Temperature and Efficiency

This technical document discusses: 1. Inverters and battery chargers are rated at specific temperatures and their continuous output decreases as temperature increases due to derating. 2. Power loss and efficiency are related to load and temperature - efficiency peaks at medium loads and decreases at high loads and temperatures due to increased losses. 3. Derating curves are based on limiting components like semiconductors and transformers, with semiconductors limiting battery chargers and transformers limiting inverters. Output current decreases as temperature rises to prevent exceeding maximum component temperatures.

Uploaded by

marckalhi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
45 views

Output Rating Operating Temperature and Efficiency

This technical document discusses: 1. Inverters and battery chargers are rated at specific temperatures and their continuous output decreases as temperature increases due to derating. 2. Power loss and efficiency are related to load and temperature - efficiency peaks at medium loads and decreases at high loads and temperatures due to increased losses. 3. Derating curves are based on limiting components like semiconductors and transformers, with semiconductors limiting battery chargers and transformers limiting inverters. Output current decreases as temperature rises to prevent exceeding maximum component temperatures.

Uploaded by

marckalhi
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

11-03-2016

Technical notes on output rating, operating


temperature and efficiency
1. Inverters: continuous output rating as function of temperature
In our datasheets inverters, and the inverter function of Multis and Quattros, are rated at
25C (75F). On average, derating at higher temperatures is as shown below (see
paragraph 4 for the theoretical background).

Temperature Cont. output


C F %
Low temp. 100
25 77 100
30 86 96
35 95 93
40 104 90
50 122 82
60 140 75
65 149 69
High temp. 0

Power vs temperature
110%

100%

90%
Output

80%

70%

60%

50%

40%
20 30 40 50 60 70
Temperature (C)
2. Battery chargers: continuous output rating as a function of
temperature
In our datasheets battery chargers are rated at 40C (104F). The battery charger
function of our Multis and Quattros is rated at 25C (77F). As explained in paragraph 4,
derating for higher temperatures is approximately as follows:

Blue curve: products rated at Red curve: products rated at


25C (77F) 40C (104F)
Temperature Cont. output Temperature Cont. output
C F % C F %
25 77 100
30 86 95
35 95 88
40 104 80 40 104 100
50 122 62 50 122 77
60 140 36 60 140 45
65 149 0 65 149 0
3. Power loss and efficiency as a function of load
As an example let us look at the Phoenix Inverter 24/3000 or MultiPlus 24/3000/70 (both
products have the same inverter). These products use high frequency switching to
generate a sinewave, which is then transformed to the required output voltage by two
toroidal transformers. Toroidal transformers have a higher efficiency and less no load
losses than the more common E-core transformers.
The measured efficiency curve is shown below:

Output power (W) Dissipation (W) Efficiency (%)


0 20 0
10 20 33,3
30 20 59,9
100 21 83,0
400 28 93,5
800 52 93,9
1600 148 91,5
2500 333 88,3
4000 820 83,0
5000 1270 79,7
4. The theory behind the graphs of paragraph 1 3

4.1. Operating temperature range


The operating temperature range may vary from one product to another.
The upper temperature is limited by the maximum operating temperature of certain
components (for ex. semiconductors, electrolytic capacitors, relays).
The low temperature limit is mainly limited by the minimum operating temperature of
semiconductors and electrolytic capacitors.

As has been shown in section 1 and 2, this does not mean that the full output rating is
available over the whole temperature range.
Derating is needed at high ambient temperatures to prevent overheating of a.o. power
semiconductors and transformers.
In general, output power cannot be increased at low temperatures due the maximum current
rating of certain components (terminals, core saturation of filter chokes).

4.2. Power loss and efficiency


Electric current generates heat in the conductor through which it flows. The basic formula to
calculate the rate of heat generation, or power dissipation, is:

P = R x I (1)

where P stands for power (measured in Watts), R (Ohm) is the resistance of the conductor
and I (Ampre, or Amps) the current.

What is interesting about this formula is that it shows that power dissipation increases with
the square of the current. A resistance of for example 2 Ohm and a current of 10 Amps
results in a dissipation of 2 x 10 x 10 = 200 W. Twice that current results in 4 times more heat
generated: 2 x 20 x 20 = 800 W!

In power electronic circuits the situation is much more complicated: one has to do with DC
losses and switching losses, losses in semiconductors and in high frequency transformers,
etc. Very often, however, formula (1) appears to be a fairly good approximation of the overall
losses in the circuit. The power dissipation P of the circuit can then be calculated by defining
R as the overall resistance between input and output of the circuit and I as the output current.

An even better approximation is obtained if a factor is added to (1) to account for the no-load
power consumption or no-load power dissipation. The no-load power consumption is the
power dissipated by the circuit when it is switched on without any load connected. It is an
important specification especially of inverters since in the long run it can drain a battery.

Taking into account the no-load power consumption results in the following formula:

Ploss = Po + R x Iout (2)

Ploss is the total power dissipation in the product; Po is the no-load power dissipation (and by
definition also the no-load power consumption); R is the resistance between input and
output; and Iout the output current.

With formula (2) efficiency, an important specification of inverters, can be calculated:

= 100 x Pout / (Pout + Ploss) (3)

where is the efficiency in % and Pout the output power (Pout = Vout x Iout).
At no-load conditions the output current Iout = 0 and the output power Pout = 0, so that:

Ploss = Po (4)

and:

= 0 / (0 + Po) = 0 % (5)

In other words: the efficiency is 0 at no-load.

If there would be no power dissipation in the circuit (Ploss = 0), then:

= 100 x Pout / (Pout + 0) = 100 % (6)

In words: if an ideal circuit without any losses could be made, efficiency would be 100 %.

Formula (2) shows that with increasing load the losses at first do not increase very quickly
because Po will still be very much larger than R x Iout as long as Iout is small. Efficiency will
start at 0 and increase when the load increases.

But with the load increasing further, R x Iout will increase even faster and become larger
than Po, so that Ploss will start increasing approximately with the square of the load or output
current. After reaching a maximum, efficiency will therefore start decreasing as the load
increases further.

4.3. High temperature and derating


All power conversion products of Victron Energy are protected against damage due to
overheating by temperature sensors placed on transformers and on the heatsink of the
hottest semiconductors.

Inverters: When the power semiconductors and / or transformers reach a preset


temperature, inverters will first show a temperature pre-warning, and if temperature
increases further, the inverter will shut down. After cooling down, it will restart.

Battery chargers: When the power semiconductors and / or transformers reach a preset
temperature, the output current will automatically be reduced to prevent a further increase in
temperature.

The power semiconductors are the most critical, with a preset maximum heatsink
temperature of approximately 80C (167F).
High frequency magnetics are in general limited to 100C, and toroidal transformers to
110C.

The derating curve resulting from maximum heatsink temperature will therefore show a
steeper downward slope than the derating curve resulting from high frequency magnetics or
a toroidal transformer.

In general the toroidal transformer is the limiting factor in our inverters and inverter/chargers,
while semiconductors are the limiting factor in our battery chargers. This explains the
difference between the curves shown in paragraph 1 and paragraph 2.

Knowing that, in case of forced cooling, the cooling capacity of a heatsink or transformer is
proportional to the temperature difference between the heatsink/transformer and the cooling
air flow, formula (2) can be restated as follows:
Iout = K x (Tmax - To - Tamb) (7)

where Iout is the output current; K is a constant; Tmax is the maximum heatsink or transformer
temperature; To is the temperature rise of the heatsink or transformer due to the no-load
power dissipation; and Tamb is the temperature of the cooling air flow.

Formula (7) shows that when To + Tamb = Tmax, Iout = 0.


In words: when the ambient temperature is so high that the no load power dissipation alone
will cause the heatsink or transformer to reach the maximum temperature limit, the output
current of the circuit is 0. Any output current would increase temperature beyond the
maximum and result in shut down of the circuit due to overheating.

The derating formula (7) is applicable when the ambient temperature increases beyond the
temperature at which the full output power is specified, in general 25C (77F) for inverters
and 40C (104F) for battery chargers.

Why 25C (77F) for inverters? Inverters are very often used with intermittent loads. Short
term power and peak power are therefore more important than the continuous rated power.
Battery chargers on the contrary will regularly operate at maximum output current for several
hours and are therefore rated for continuous operation at 40C (104F).

You might also like