Rock mass properties for surface mines

Evert Hoek and Antonio Karzulovic

Published in Slope Stability in Surface Mining, (Edited by W.A. Hustralid, M.K.

McCarter and D.J.A. van Zyl), Littleton, Colorado: Society for Mining, Metallurgical
and Exploration (SME), 2000, pages 59-70.
Page 2Brown criterion for surface mining
Hoek Hoek-Brown criterion for surface mining
Page 2

Rock mass properties for surface mines

Evert Hoek* and Antonio Karzulovic**

1.1 INTRODUCTION

Reliable estimates of the strength and deformation characteristics of rock masses are
required for almost any form of analysis used for the design of surface excavations.
Hoek and Brown (1980a, 1980b) proposed a method for obtaining estimates of the
strength of jointed rock masses, based upon an assessment of the interlocking of rock
blocks and the condition of the surfaces between these blocks. This method was
modified over the years in order to meet the needs of users who applied it to problems
that were not considered when the original criterion was developed (Hoek 1983,
Hoek and Brown 1988). The application of the method to very poor quality rock
masses required further changes (Hoek, Wood and Shah 1992) and, eventually, the
development of a new classification called the Geological Strength Index (Hoek
1994, Hoek, Kaiser and Bawden 1995, Hoek and Brown 1997, Hoek, Marinos and
Benissi (1998)). A review of the development of the criterion and of the equations
proposed at various stages in this development is given in Hoek and Brown (1997).
This chapter presents the Hoek-Brown criterion in a form that has been found
practical in the field and that appears to provide the most reliable set of results for use
as input for methods of analysis currently used in rock engineering.
For surface excavations, the rock mass properties are particularly sensitive to
stress relief and blast damage and these two factors are discussed in his chapter.

1.2 GENERALISED HOEK-BROWN CRITERION

The Generalised Hoek-Brown failure criterion for jointed rock masses is defined by:
' a
1 =' +' mb 3+ s (1.1)
3 ci
ci

where 1' and '3 are the maximum and minimum effective stresses at failure,

mb is the value of the Hoek-Brown constant m for the rock mass,

s and a are constants which depend upon the rock mass characteristics, and
ci is the uniaxial compressive strength of the intact rock pieces.

* Consulting engineer, Vancouver, Canada.

** Professor, Department of Mining Engineering, University of Chile, Santiago, Chile
Page 3Brown criterion for surface mining
Hoek Hoek-Brown criterion for surface mining
Page 3

The Mohr envelope, relating normal and shear stresses, can be determined by the
method proposed by Hoek and Brown (1980a). In this approach, equation 1.1 is used
to generate a series of triaxial test values, simulating full scale field tests, and a
statistical curve fitting process is used to derive an equivalent Mohr envelope defined
by the equation:
B
' tm
= A ci n (1.2)
ci

where A and B are material constants

'n is the normal effective stress, and
tm is the tensile strength of the rock mass.

In order to use the Hoek-Brown criterion for estimating the strength and
deformability of jointed rock masses, three properties of the rock mass have to be
estimated. These are

1. the uniaxial compressive strength ci of the intact rock elements,

2. the value of the Hoek-Brown constant mi for these intact rock elements, and
3. the value of the Geological Strength Index GSI for the rock mass.

1.3 INTACT ROCK PROPERTIES

For the intact rock pieces that make up the rock mass equation 1.1 simplifies to:
0.5
' ' 3'
1 = 3 + ci mi +1 (1.3)
ci

The relationship between the principal stresses at failure for a given rock is defined
by two constants, the uniaxial compressive strength ci and a constant mi .

Wherever possible the values of these constants should be determined by statistical

analysis of the results of a set of triaxial tests on carefully prepared core samples.
When laboratory tests are not possible, Table 1.1 and Table 1.2 can be used to obtain
estimates of ci and mi .
In the case of mineralised rocks, the effects of alteration can have a significant
impact on the properties of the intact rock components and this should be taken into
account in estimating the values of ci and mi . For example, the influence of quartz-
seritic alteration of andesite and porphyry is illustrated in the Figure 1.1. Similar
trends have been observed for other forms of alteration and, where this type of effect
is considered likely, the geotechnical engineer would be well advised to invest in a
program of laboratory testing to establish the appropriate properties for the intact
rock.
Page 4Brown criterion for surface mining
Hoek Hoek-Brown criterion for surface mining
Page 4

100

Percentage uniaxial compressive strength

Porphyry
Andesite
80 Quartz-monzonite porhpyry
Andesite

60

40

20

0
Light Moderate Intense Very Intense

Quartz -sericite alteration

Figure 1.1: Influence of quartz-seritic alteration on the uniaxial compressive strength

of intact specimens of andesite and porphyry.

The Hoek-Brown failure criterion, which assumes isotropic rock and rock mass
behaviour, should only be applied to those rock masses in which there are a sufficient
number of closely spaced discontinuities, with similar surface characteristics, that
isotropic behaviour involving failure on multiple discontinuities can be assumed.
When the structure being analysed is large and the block size small in comparison,
the rock mass can be treated as a Hoek-Brown material.
Where the block size is of the same order as that of the structure being analysed or
when one of the discontinuity sets is significantly weaker than the others, the Hoek-
Brown criterion should not be used. In these cases, the stability of the structure should
be analysed by considering failure mechanisms involving the sliding or rotation of blocks
and wedges defined by intersecting structural features. Figure 1.2 summarises these
statements in a graphical form.

1.4 GEOLOGICAL STRENGTH INDEX

The strength of a jointed rock mass depends on the properties of the intact rock pieces
and also upon the freedom of these pieces to slide and rotate under different stress
conditions. This freedom is controlled by the geometrical shape of the intact rock
pieces as well as the condition of the surfaces separating the pieces. Angular rock
pieces with clean, rough discontinuity surfaces will result in a much stronger rock
mass than one which contains rounded particles surrounded by weathered and altered
material.
Page 5Brown criterion for surface mining
Hoek Hoek-Brown criterion for surface mining
Page 5

Table 1.1: Field estimates of uniaxial compressive strength.

Uniaxial Point
Comp. Load Field estimate of
Grade* Term Strength Index strength Examples

(MPa) (MPa)
R6 Extremely > 250 >10 Specimen can only be Fresh basalt, chert,
Strong chipped with a diabase, gneiss, granite,
geological hammer quartzite

R5 Very 100 - 250 4 - 10 Specimen requires many Amphibolite, sandstone,

strong blows of a geological basalt, gabbro, gneiss,
hammer to fracture it granodiorite, peridotite ,
rhyolite, tuff

R4 Strong 50 - 100 2-4 Specimen requires more Limestone, marble,

than one blow of a sandstone, schist
geological hammer to
fracture it

R3 Medium 25 - 50 1-2 Cannot be scraped or Concete, phyllite, schist,

strong peeled with a pocket siltstone
knife, specimen can be
fractured with a single
blow from a geological
hammer

R2 Weak 5 - 25 ** Can be peeled with a Chalk, claystone, potash,

pocket knife with marl, siltstone, shale,
difficulty, shallow rocksalt,
indentation made by
firm blow with point of
a geological hammer

R1 Very 1-5 ** Crumbles under firm Highly weathered or

weak blows with point of a altered rock, shale
geological hammer, can
be peeled by a pocket
knife

R0 Extremely 0.25 - 1 ** Indented by thumbnail Stiff fault gouge

weak

* Grade according to Brown (1981).

** Point load tests on rocks with a uniaxial compressive strength below 25 MPa are likely to yield
highly ambiguous results.
Page 6Brown criterion for surface mining
Hoek Hoek-Brown criterion for surface mining
Page 6

Table 1.2: Values of the constant mi for intact rock, by rock group. Note that values
in parenthesis are estimates.

Rock Class Group Texture

type Coarse Medium Fine Very fine
Conglomerates Sandstones Siltstones Claystones
( 21 3) 17 4 72 42
Breccias Greywackes Shales
Clastic
(19 5) (18 3) (6 2)
Marls
(7 2)
SEDIMENTARY

Crystalline Sparitic Micritic Dolomites

Limestone Limestones Limestones (9 3)
(12 3) ( 10 2) (9 2 )

Non- Gypsum Anhydrite

Clastic Evaporites 82 12 2

Chalk
Organic
72
Marble Hornfels (19 Quartzites
Non Foliated 93 4) 20 3
Metasandstone
METAMORPHIC

(19 3)
Migmatite Amphibolites
Slightly foliated (29 3) 26 6

Foliated* Gneiss Schists Phyllites Slates

28 5 12 3 (7 3) 74

Granite Diorite
32 3 25 5
Light Granodiorite
(29 3)
Plutonic
Gabbro
Dolerite
27 3
Dark (16 5)
Norite
20 5
IGNEOUS

Hypabyssal Porphyries Diabase Peridotite

(20 5) (15 5) (25 5)

Rhyolite Dacite Obsidian

(25 5) (25 3) (19 3)
Lava
Andesite Basalt
Volcanic 25 5 (25 5)

Pyroclastic Agglomerate Breccia Tuff

(19 3) (19 5) (13 5)

* These values are for intact rock specimens tested normal to bedding or foliation. The value of mi will
be significantly different if failure occurs along a weakness plane.
Page 7Brown criterion for surface mining
Hoek Hoek-Brown criterion for surface mining
Page 7

Intact rock specimens

- use equation 1.3

One joint set - do not use

Hoek-Brown criterion

Two joint sets - do not

use Hoek-Brown criterion

Many joints - use equation

1.1 with caution

Heavily jointed rock mass

- use equation 1.1

Figure 1.2: Idealised diagram showing the transition from intact to a heavily
jointed rock mass with increasing sample size.

The Geological Strength Index (GSI), introduced by Hoek (1994) and Hoek, Kaiser
and Bawden (1995) provides a system for estimating the reduction in rock mass
strength for different geological conditions. This system is presented in Table 1.3, for
blocky rock masses, and Table 1.4 for schistose metamorphic rocks.
Once the Geological Strength Index has been estimated, the parameters that
describe the rock mass strength characteristics, are calculated as follows:

GSI 100
mb = mi exp (1.4)
28
Page 8Brown criterion for surface mining
Hoek Hoek-Brown criterion for surface mining
Page 8

For GSI > 25, i.e. rock masses of good to reasonable quality:

GSI 100
s = exp (1.5)
9
and

a = 0.5 (1.6)

For GSI < 25, i.e. rock masses of very poor quality:
s=0 (1.7)
and
GSI
a = 0.65 (1.8)
200

For better quality rock masses (GSI > 25), the value of GSI can be estimated directly
from the 1976 version of Bieniawskis Rock Mass Rating, with the Groundwater
rating set to 10 (dry) and the Adjustment for Joint Orientation set to 0 (very
favourable) (Bieniawski 1976). For very poor quality rock masses the value of RMR
is very difficult to estimate and the balance between the ratings no longer gives a
reliable basis for estimating rock mass strength. Consequently, Bieniawskis RMR
classification should not be used for estimating the GSI values for poor quality rock
masses (RMR < 25) and the GSI charts should be used directly.
If the 1989 version of Bieniawskis RMR classification (Bieniawski 1989) is used,
then GSI = RMR89 - 5 where RMR89 has the Groundwater rating set to 15 and the
Adjustment for Joint Orientation set to zero.

1.5 MOHR-COULOMB PARAMETERS

Most geotechnical software is written in terms of the Mohr-Coulomb failure criterion

in which the rock mass strength is defined by the cohesive strength c and the angle of
friction . The linear relationship between the major and minor principal stresses,
1' and 3' , for the Mohr-Coulomb criterion is
1' = cm + k3' (1.9)

where cm is the uniaxial compressive strength of the rock mass and k is the slope of

the line relating 1' and '3 . The values of and c can be calculated from

k 1
sin ' = (1.10)
k +1
'
' cm (1 sin )
c = (1.11)
2 cos '
Page 9Brown criterion for surface mining
Hoek Hoek-Brown criterion for surface mining
Page 9

Table 1.3: Characterisation of a blocky rock masses on the basis of particle

interlocking and discontinuity condition. After Hoek, Marinos and Benissi (1998).
Page 10
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
10

Table 1.4: Characterisation of a schistose metamorphic rock masses on the basis of

foliation and discontinuity condition. (After M. Truzman, 1999)
Page 11
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
11

There is no direct correlation between equation 1.9 and the non-linear Hoek-Brown
criterion defined by equation 1.1. Consequently, determination of the values of c and
for a rock mass that has been evaluated as a Hoek-Brown material is a difficult
problem.
Having considered a number of possible approaches, it has been concluded that
the most practical solution is to treat the problem as an analysis of a set of full-scale
triaxial strength tests. The results of such tests are simulated by using the Hoek-
Brown equation 1.1 to generate a series of triaxial test values. Equation 1.9 is then
fitted to these test results by linear regression analysis and the values of c and are
determined from equations 1.11 and 1.10. A full discussion on the steps required to
carry out this analysis is presented in the Appendix, together with a spreadsheet for
implementing this analysis.
The range of stresses used in the curve fitting process described above is very
important. For the confined conditions surrounding tunnels at depths of more than
about 30 m, the most reliable estimates are given by using a confining stress range
from zero to 0.25 ci , where ci is the uniaxial compressive strength of the intact

rock elements. For this stress range, the uniaxial compressive strength of the rock
mass cm , the cohesive strength c and the friction angle are given in Figures 1.3

and 1.4.
For slopes and shallow excavations the user is given the choice of the stress
range for this curve fitting process. This is discussed in full in the Appendix.

1.0

0.9
Rock mass strength cm / Intact strength ci

mi
0.8
35
30
0.7
25
0.6

0.5

0.4

0.3 20
15
0.2
10
5
0.1
0.0
0 10 20 30 40 50 60 70 80 90 100

Geological Strength Index GSI

Figure 1.3: Ratio of uniaxial compressive strength of rock mass to intact rock versus
Geological Strength Index GSI for depths of more than 30 m.
Page 12
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
12

0.20

Cohesive strength / Uniaxial strength of intact rock

0.10

0.08

0.06
0.05
0.04

0.03
mi
35
30 0.02
25
2
18160
1412
1
70 0.01
5
0.008
10 20 30 40 50 60 70 80 90

Geological Strength Index GSI

a. Plot of ratio of cohesive strength c to uniaxial compressive

strength ci for depths of more than 30 m.

55 mi
35
50 30
25
20
45 18
16
14
Friction angle - degrees

12
40
10

35 7

30 5

25

20

15

10
10 20 30 40 50 60 70 80 90

Geological Strength Index GSI

b. Plot of friction angle

Figure 1.4: Cohesive strengths and friction angles for different GSI and mi values for
depths of more than 30 m.
Page 13
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
13

1.6 DEFORMATION MODULUS

Serafim and Pereira (1983) proposed a relationship between the in situ modulus of
deformation and Bieniawskis RMR classification. This relationship is based upon
back analysis of dam foundation deformations and it has been found to work well for
better quality rocks. However, for many of the poor quality rocks it appears to predict
deformation modulus values that are too high. Based upon practical observations and
back analysis of excavation behaviour in poor quality rock masses, the following
modification to Serafim and Pereiras equation is proposed for ci < 100 :

GSI 10
ci 40
Em = 10 (1.12)
100

Note that GSI has been substituted for RMR in this equation and that the modulus Em
is reduced progressively as the value of ci falls below 100. This reduction is based

upon the reasoning that the deformation of better quality rock masses is controlled by
the discontinuities while, for poorer quality rock masses, the deformation of the intact
rock pieces contributes to the overall deformation process.
Based upon measured deformations, equation 1.12 appears to work reasonably
well in those cases where it has been applied. However, as more field evidence is gathered
it may be necessary to modify this relationship.

180 ci = 100 MPa

160

140
Deformation modulus E - GPa

ci = 50 MPa
120

100 ci = 30MPa

80
ci = 15 MPa
60
ci = 10 MPa

40 ci = 5 MPa

20 ci = 1MPa

0
0 10 20 30 40 50 60 70 80 90 100

Geological Strength Index GSI

Figure 1.5: Deformation modulus versus Geological Strength Index GSI.

Page 14
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
14

1.7 STRESS RELAXATION

When the rock mass adjacent to a tunnel wall or a slope is excavated, a relaxation of
the confining stresses occurs and the remaining material is allowed to expand in
volume or to dilate. This has a profound influence on the strength of the rock mass
since, in jointed rocks, this strength is strongly dependent upon the interlocking
between the intact rock particles that make up the rock mass.
As far as the authors are aware, there is very little research evidence relating the
amount of dilation to the strength of a rock mass. One set of observations that gives
an indication of the loss of strength associated with dilation is derived from the
support required to stabilise tunnels. Sakurai (1983) suggested that tunnels in which
the strain, defined as the ratio of tunnel closure to tunnel diameter, exceeds 1% are
likely to suffer significant instability unless adequately supported. This suggestion
was confirmed in observations by Chern et al (1998) who recorded the behaviour of a
number of tunnels excavated in Taiwan. They found that all of those tunnels that
exhibited strains of greater than 1 to 2% required significant support. Tunnels
exhibiting strains as high as 10% were successfully stabilised but the amount of effort
required to achieve this stability increased in proportion to the amount of strain.
While it is not possible to derive a direct relationship between rock mass strength
and dilation from these observations, it is possible to conclude that the strength loss is
significant. An unconfined surface that has deformed more than 1 or 2% (based upon
Sakurais definition of strain) has probably reached residual strength in which all of
the effective cohesive strength of the rock mass has been lost. While there are no similar
observations for rock slopes, it is reasonable to assume that a similar loss of strength
occurs as a result of dilation. Hence, a 100 m high slope which has suffered a total crest
displacement of more than 1 m (i.e. more than 1% strain) may start to exhibit
significant signs of instability as a result of loss of strength of the rock mass.

1.8 BLAST DAMAGE

Blast damage results in a loss of rock mass strength due to the creation of new
fractures and the wedging open of existing fractures by the penetration of explosive
gasses. In the case of very large open pit mine blasts, this damage can extend as much
as 100 m behind the final row of blast holes.
In contrast to the strength loss due to stress relaxation or dilation, discussed in the
previous section, it is possible to arrive at an approximate quantification of the
strength loss due to blast damage. This is because the blast is designed to achieve a
specific purpose which is generally to produce a fractured rock mass that can be
excavated by means of a given piece of equipment.
Figure 1.6 presents a plot of 23 case histories of excavation by digging, ripping
and blasting published by Abdullatif and Cruden (1983). These case histories are
summarised in Table 1.5. The values of GSI are estimated from the data contained in
the paper by Abdullatif and Cruden while the rock mass strength values were
calculated by means of the spreadsheet given in the appendix, assuming an average
slope height of 15 m.
Page 15
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
15

These examples shows that rock masses can be dug, obviously with increasing
difficulty, up to GSI values of about 40 and rock mass strength values of about 1
MPa. Ripping can be used up to GSI values of about 60 and rock mass strength
values of about 10 MPa, with two exceptions where heavy equipment was used to rip
strong rock masses. Blasting was used for GSI values of more than 60 and rock mass
strengths of more than about 15 MPa.
Consider the case of an open pit slope excavated in granodiorite. The uniaxial
compressive strength of the intact rock is ci = 60 MPa and the Geological Strength Index
is GSI = 55. For granodiorite, Table 2 gives the value of mi = 30. Substitution of these
values into the spreadsheet given in the appendix, for a single 18 m high bench,
gives a rock mass strength cm= 5.7 MPa. In order to create conditions for easy digging,
the blast is designed to reduce the GSI value to below 40 and/or the rock mass
strength to less than 1 MPa. In this case the controlling parameter is the rock mass
strength and the spreadsheet given in the appendix shows that the GSI value has to be
reduced to about 22 on order to achieve this rock mass strength.
In another example of a 15 m high slope in weak sandstone, the compressive
strength of the intact rock is ci = 10 MPa, mi = 17 and GSI = 60. These values give a
rock mass strength cm= 1.4 MPa and this is reduced to 0.7 by reducing the GSI to 40.
Hence, in this case, both the conditions for efficient digging in this soft rock are
satisfied by designing the blast to give a GSI value of 40.

100

Excavation method
Dig
Rip
Rock mass strength ci - MPa

Blast

10

0.1
0 10 20 30 40 50 60 70 80 90 100

Geological Strength Index GSI

Figure 1.6: Plot of rock mass strength versus GSI for different excavation methods,
after Abdullatif and Cruden (1983).
Page 16
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
16

Table 1.5: Summary of methods used to excavate rock masses with a range of
uniaxial compressive strength values, based on data published by Abdullatif and
Cruden (1983).
Rock mass
GSI strength Excavation method

cm - MPa
85 86 Blasting
85 117 Blasting
77 64 Blasting
77 135 Blasting
77 84 Blasting
76 54 Blasting
71 35 Blasting
69 15 Blasting
68 17 Blasting
68 30 Blasting
67 42 Ripping by D9L bulldozer
67 33 Ripping by D9L bulldozer
58 2.4 Ripping by track loader
57 9.5 Ripping by 977L track loader
51 0.8 Ripping by track loader
42 1.2 Digging by 977L track loader
40 0.5 Digging by wheel loader
34 0.5 Digging by hydraulic face shovel
25 0.3 Digging by 977L track loader
24 0.2 Digging by wheel loader
25 0.2 Digging by hydraulic backhoe
19 0.1 Digging by D9 bulldozer
19 0.1 Digging by 977L track loader

Figure 1.7: Diagrammatic representation of the transition between the in situ rock
mass and blasted rock that is suitable for digging.
Page 17
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
17

Figure 1.7 summarises the conditions for a muckpile that can be dug efficiently and
the blast damaged rock mass that lies between the digging limit and the in situ rock mass.
The properties of this blast damaged rock mass will control the stability of the slope that
remains after digging of the muckpile has been completed.
The thickness D of the blast damaged zone will depend upon the design of the
blast. Based upon experience, the authors suggest that the following approximate
relationships can be used as a starting point in judging the extent of the blast damaged
zone resulting from open pit mine production blasting:

Large production blast, confined and with little or D = 2 to 2.5 H

no control
Production blast with no control but blasting to a D = 1 to 1.5 H
free face
Production blast, confined but with some control, D = 1 to 1.2 H
e.g. one or more buffer rows
Production blast with some control, e.g. one or D = 0.5 to 1 H
more buffer rows, and blasting to a free face
Carefully controlled production blast with a free D = 0.3 to 0.5 H
face
Page 18
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
18

1.9 REFERENCES

Abdullatif, O.M. and Cruden, D.M. 1983. The relationship between rock mass quality
and ease of excavation. Bull. Intnl. Assoc. Eng. Geol. No. 28. 183-187.
Balmer G. 1952. A general analytical solution for Mohr's envelope. Am. Soc. Test.
Mat. 52, 1260-1271.
Bieniawski Z.T. 1976. Rock mass classification in rock engineering. In Exploration
for Rock Engineering, Proc. of the Symp., (Edited by Bieniawski Z.T.) 1, 97-106.
Cape Town, Balkema.
Bieniawski Z.T. 1989. Engineering Rock Mass Classifications. p. 251. New York,
Wiley.
Brown E.T. (Ed). 1981. Rock characterization, testing and monitoring - ISRM
suggested methods, 171-183. Oxford, Pergamon.
Chern, J.C., Yu, C.W. and Shiao, F.Y. 1998. Tunnelling in squeezing ground and
support estimation. Proc. Regional Symposium on Sedimentary Rock Engineering,
Taipei. 192-202.
Hoek E. 1994. Strength of rock and rock masses, ISRM News Journal, 2(2), 4-16.
Hoek E. and Brown E.T. 1980. Underground excavations in rock, p. 527. London,
Instn Min. Metall.
Hoek E. and Brown E.T. 1988 The Hoek-Brown failure criterion - a 1988 update. In
Rock Engineering for Underground Excavations, Proc. 15th Canadian Rock
Mech. Symp. (Edited by Curran J.C.), 31-38. Toronto, Dept. Civil Engineering,
University of Toronto.
Hoek E. Strength of jointed rock masses, 1983. 23rd Rankine Lecture. Gotechnique
33(3), 187-223.
Hoek E., Kaiser P.K. and Bawden W.F. 1995. Support of underground excavations in
hard rock. p. 215. Rotterdam, Balkema.
Hoek E., Wood D. and Shah S. 1992. A modified Hoek-Brown criterion for jointed
rock masses. Proc. Rock Characterization, Symp. Int. Soc. Rock Mech.: Eurock
92, (Edited by Hudson J.A.), 209-214. London, Brit. Geotech. Soc.
Hoek, E. and Brown, E.T. 1980. Empirical strength criterion for rock masses. J.
Geotech. Engng. Div., ASCE, 106 (GT 9), 1013-1035.
Hoek, E. and Brown, E.T. 1997. Practical estimates or rock mass strength. Int. J.
Rock Mech. & Mining Sci. & Geomechanics Abstracts. 34(8), 1165-1186.
Hoek, E., Marinos, P. and Benissi, M. 1998. Applicability of the Geological Strength
Index (GSI) classification for very weak and sheared rock masses. The case of the
Athens Schist Formation. Bull. Engg. Geol. Env. 57(2), 151-160.
Sakurai, S. 1983. Displacement measurements associated with the design of
underground openings. Proc. Intnl. Symp. Field Measurements in Geomechanics,
Zurich. Vol. 2, 1163-1178.
Page 19
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
19

Serafim, J.L. and Pereira, J.P. 1983. Consideration of the Geomechanics

Classification of Bieniawski. Proc. Intnl. Symp. Engng. Geol. And Underground
Construction. Lisbon, Portugal, Vol. 1, Part 11, 33-44.
Truzman, M, 1999, personal communication.
Page 20
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
20

1.10 APPENDIX DETERMINATION OF MOHR COULOMB CONSTANTS

The steps required to determine the parameters A, B, c and are given below. A
spreadsheet for carrying out this analysis, with a listing of all the cell formulae, is
given in Figure 1.8.
The relationship between the normal and shear stresses can be expressed in terms
of the corresponding principal effective stresses as suggested by Balmer (1952):

1' 3'
' = ' + (1.13)
n 3
1' '3 + 1

= (1' 3' ) 1' 3' (1.14)

For the GSI > 25, when a = 0.5:

' mb ci
1
= + (1.15)

1
3' 2(1' 3' )
For GSI < 25, when s = 0:
a 1
' '
1 = 1 + am a 3 (1.16)
b
3' ci

The tensile strength of the rock mass is calculated from:

2
= m m + 4s (1.17)
ci
tm b b
2

The equivalent Mohr envelope, defined by equation 1.2, may be written in the form
Y = log A + BX (1.18)

where
n' tm
Y = log , X = log (1.19)
ci ci

Using the value of tm calculated from equation 1.17 and a range of values of and
'
Page 21
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
21
n calculated from equations 1.13 and 1.14 the values of A and B are determined by
linear regression where :
XY ( X Y) T
B= (1.20)
2 2
X ( X) T
Page 22
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
22

A = 10^ ( Y T B( X T ) ) (1.21)

and T is the total number of data pairs included in the regression analysis.
The most critical step in this process is the selection of the range of '3 values. As far

as the authors are aware, there are no theoretically correct methods for choosing this
range and a trial and error method, based upon practical compromise, has been used
for selecting the range included in the spreadsheet presented in Figure 1.9.
For a Mohr envelope defined by equation 1.2, the friction angle 'i for a specified

normal stress 'ni is given by:

B 1
' 'ni tm
= arctan AB (1.22)
i
ci

The corresponding cohesive strength ci' is given by:

c i' = '
ni tan i' (1.23)

and the corresponding uniaxial compressive strength of the rock mass is :

2ci' cos 'i

cmi = (1.24)
1 sin i'

The values of c and obtained from this analysis are very sensitive to the range of
values of the minor principal stress '3 used to generate the simulated full-scale

triaxial test results. On the basis of trial and error, it has been found that the most
consistent results for deep excavations (depth > 30 m below surface) are obtained
when 8 equally spaced values of '3 are used in the range 0 < 3 < 0.25ci. For

shallow excavations and slopes, the user should input the depth below surface of the
anticipated failure surface and the unit weight of the rock mass. For typical slopes, the
depth of the failure surface can be assumed to be equal to the slope height.
Page 23
Hoek Brown criterion for surface mining Hoek-Brown criterion for surfacePage
mining
23

Figure 1.8: Spreadsheet for calculation of Hoek-Brown and equivalent Mohr-

Coulomb parameters for shallow excavations and slopes.

Input: sigci = 30 MPa mi = 15 GSI = 55

Depth of failure surface or tunnel below slope = 25 m Unit wt. = 0.027 MN/n3

Output: stress = 0.68 MPa mb = 3.01 s = 0.0067

a= 0.5 sigtm = -0.0672 MPa A = 0.7086
B= 0.7263 k= 9.19 phi = 53.48 degrees
coh = 0.494 MPa sigcm = 3.00 MPa E = 7304.0 MPa

Calculation:
Sums
sig3 1E-10 0.10 0.19 0.29 0.39 0.48 0.58 0.68 2.70
sig1 2.46 3.94 5.04 5.96 6.78 7.52 8.21 8.86 48.77
ds1ds3 19.32 12.74 10.31 8.95 8.06 7.41 6.91 6.51 80.20
sign 0.12 0.38 0.62 0.86 1.09 1.32 1.54 1.76 7.70
tau 0.53 1.00 1.38 1.70 2.00 2.28 2.54 2.78 14.21
x -2.20 -1.83 -1.64 -1.51 -1.41 -1.34 -1.27 -1.21 -12.42
y -1.75 -1.48 -1.34 -1.25 -1.18 -1.12 -1.07 -1.03 -10.21
xy 3.85 2.71 2.19 1.88 1.66 1.49 1.36 1.25 16.41
xsq 4.85 3.35 2.69 2.28 2.00 1.78 1.61 1.47 20.04
sig3sig1 0.00 0.38 0.97 1.72 2.61 3.63 4.75 5.98 20
sig3sq 0.00 0.01 0.04 0.08 0.15 0.23 0.33 0.46 1
taucalc 0.53 1.00 1.37 1.70 2.00 2.28 2.54 2.79
sig1sig3fit 3.00 3.88 4.77 5.65 6.54 7.42 8.31 9.20
signtaufit 0.66 1.00 1.33 1.65 1.97 2.28 2.58 2.88

Cell formulae:
stress = if(depth>30, sigci*0.25,depth*unitwt*0.25)
mb = mi*EXP((GSI-100)/28)
s = IF(GSI>25,EXP((GSI-100)/9),0)
a = IF(GSI>25,0.5,0.65-GSI/200)
sigtm = 0.5*sigci*(mb-SQRT(mb^2+4*s))
sig3 = Start at 1E-10 (to avoid zero errors) and increment in 7 steps of stress/28 to stress/4
sig1 = sig3+sigci*(((mb*sig3)/sigci)+s)^a
ds1ds3 = IF(GSI>25,(1+(mb*sigci)/(2*(sig1-sig3))),1+(a*mb^a)*(sig3/sigci)^(a-1))
sign = sig3+(sig1-sig3)/(1+ds1ds3)
tau = (sign-sig3)*SQRT(ds1ds3)
x = LOG((sign-sigtm)/sigci)
y = LOG(tau/sigci)
xy = x*y x sq = x^2
A = acalc = 10^(sumy/8 - bcalc*sumx/8)
B = bcalc = (sumxy - (sumx*sumy)/8)/(sumxsq - (sumx^2)/8)
k = (sumsig3sig1 - (sumsig3*sumsig1)/8)/(sumsig3sq-(sumsig3^2)/8)
phi = ASIN((k-1)/(k+1))*180/PI()
coh = sigcm/(2*SQRT(k))
sigcm = sumsig1/8 - k*sumsig3/8
E = IF(sigci>100,1000*10^((GSI-10)/40),SQRT(sigci/100)*1000*10^((GSI-10)/40))
phit = (ATAN(acalc*bcalc*((signt-sigtm)/sigci)^(bcalc-1)))*180/PI()
coht = acalc*sigci*((signt-sigtm)/sigci)^bcalc-signt*TAN(phit*PI()/180)
sig3sig1= sig3*sig1 sig3sq = sig3^2
taucalc = acalc*sigci*((sign-sigtm)/sigci)^bcalc
s3sifit = sigcm+k*sig3
sntaufit = coh+sign*TAN(phi*PI()/180)