Scribd
Upload
110 views

Support Overload Manual

This document provides instructions for installing, operating, and calibrating the AD-Overload System. The system [1] simulates an overload through a known weight, [2] has two selectable levels controlled by buttons, and [3] displays the weight on a four-digit screen. It installs rapidly on elevator traction ropes and cables. Setup involves mechanically mounting the sensor plate and control unit, electrically connecting the power supply, relays, and optional measuring block. Calibration sets the zero point and adjustment parameters like full load, overload levels, car weight, and tolerances.

Uploaded by

habibulla
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
110 views

Support Overload Manual

This document provides instructions for installing, operating, and calibrating the AD-Overload System. The system [1] simulates an overload through a known weight, [2] has two selectable levels controlled by buttons, and [3] displays the weight on a four-digit screen. It installs rapidly on elevator traction ropes and cables. Setup involves mechanically mounting the sensor plate and control unit, electrically connecting the power supply, relays, and optional measuring block. Calibration sets the zero point and adjustment parameters like full load, overload levels, car weight, and tolerances.

Uploaded by

habibulla
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

ADOverloadSystem 1

ADOVERLOADSYSTEM
(UserGuide)

ADOverloadSystem 2

ADOverLoadSystem

Rapidinstallation

Costeffective

Immunetooutsidedisturbancesandvariationsinsupplyvoltage

Stablemeasurementsoverlongperiodsandinvariableconditions

FUNCTIONAL FEATURES:

Simulationofloadwithaknownweightcorrespondingtoatleast25%oftheoverload
2levelstobeselectedbyoperator
3pushbuttonsforlevelsetting,scaleandzerosetting
4digitsindicatingweightandlevels
Outputsoncleanrelaycontacts
2LEDstoviewstateofrelays
1powerLEDtoshowelectricalsupply
3LEDstoshowstate(weight,zerosetting,
Supplyinputandrelayoutputonconnectorspitch3,96mm
Eliminationofbriefvariationsinweightmeasure
Constantautomaticcalibrationofthedevice
Weightblockconnectiontoeliminateweightvariationsduringliftoperation

ELECTRICAL FEATURES:

Power input 230V AC 50Hz (with internal transformer)


Maximum power absorbed 5VA
Relay for levels C-NO-NC
Protection fuse 1A
Outputs: clean relay contacts 3A 220V AC / 1A 80V DC
Weight block input 40mA _ 2A AC/DC
ADOverloadSystem 3

MECHANICALINSTALLATION:

Themetalsensorplatemustbeinstalledonthetractionropes.Itcanbepositionednearthecarframe
asshowninthefigure.

For the sensor fixing use the following instructions (Fig) :

1. Bring the comb near to the ropes, after having inserted them and to push it until the complete ropes
fitting.
2. Bring the sensor near to the comb in order to position the ropes between the sensor and the comb.
3. Insert the fixing bolts and the washers into the sensor holes.
4. Bring the comb near to the sensor and screw hardly the bolts into the comb's hole.
5. Continue to screw with the spanner until the sensor and the comb are parallel and then in contact
between them.
6. Screw tight the bolts.
ADOverloadSystem 4

Thecontrolunitlinkedtothesensorwithcablelength3m.mustbefixednearthesensor.Forthe
controlunitfixingusethesuitablescrews.

ADOverloadSystem 5

ELECTRICALINSTALLATION
Please follow the instruction below:

1. POWER SUPPLY CONNECTION :

Make sure that your power supply fits the above values (230 AC, 50 Hz) and then connect it to the main
connector into the Overload System (Fig.).

2. RELAY CONNECTION :

Connect the outputs of the relays RELAY1 and RELAY2 to the control board in the most suitable way
for your installation, considering that the relay accept maximum 3A at 220V AC and 3A at 30V DC.

3. MEASURING BLOCK CONNECTION (OPTIONAL):

AD- Overload System has an electronic device measuring variations while lift is moving. With the
Measuring Block connections such variations can be completely eliminated. The detected weight will
be memorized while lift is moving. To activate the option Measuring Block proceed as follows:

Connect the Measuring Block Connections as

- Connect GND with the MAIN CONTROL PANEL Ground


- Connect CIL1/CIL2 with UP/DOWN or CIL command form the MAIN CONTROL PANEL
(while door closed).
- When Control Unit receives CIL signal, LED indicated by CIL will be ON.

When the lift doors are closed, the current to the terminals should be between 40mA and 4A AC/DC:
CONTROL UNIT will not to be affected by weight variations when lift moves. The car load variations do
not affect the status of relays RELAY1, RELAY2 (overload) and the weight indication on the displays.

CALIBRATION PROCEDURE

Calibration procedure for lift capacity EQUAL or INFERIOR than 999 kilos

Please follow the sequence:

1.After the perfect and careful Mechanical Installation of both Sensor and Control Unit as explained
above, Move the Lift from TOP to BOTTOM at least five times through its way for Mechanical Stress
Adjustment.

2.For calibration process stop the lift at CENTRE FLOOR and leave doors open. The units on the display
indicator are turned off.

3. Connect AD-Overload system power supply connector completely plugged in.

4. SWICH ON the control unit.

5.Wait at least 10 minutes before to begin with calibration procedure (thermic settle).
ADOverloadSystem 6

The Zero Setting process

AD Overload System is provided with ZERO SETTING When NO LOAD on the plate.

6. Now press UP , for the NEW ZERO SETTING process at Current Site Location.
( UP button has a dual function . It is used for Increment if in Edit Mode else for Zero Setting)
When unit is in Zero Setting mode then LED indicated by ZERO will start blinking. The reading on
display at that time is due to the Unloaded Cabin weight.

7.Now move the Zero Setting POT such a way that the reading will display 200 kg( because cabin-car
load is initially set at 200kg).

8. Press UP again to Exit from Zero Setting Process.

9. After Exit from Zero Setting Process the Display will indicate 00 .

The Parameter Setting process

1. Press Enter to set parameters.

Enter correct Password.(if wrong Password then Eror will be Displayed.)

COMPANY PASSWARD : P. 09

NOTE : DONT FORGET THE PASSWORD IF YOU CHANGE IT.

Press again Enter to set next parameters.

2. Press UP or DOWN to set following Parameters.

Set Full load ( F.) = 300 Kg ( Used for Relay 1)


Set Overload (H.) = 350 Kg ( Used for Relay 2 + BUZZER)
Set Carload (C.) = 200 Kg
Set Tolerance ( t.) = 25 Kg
Set Difference (d.) = 25 Kg
Set Password (P.) = 09 (Company Password)

3 . Press Enter to Exit from Parameter Setting process.


.

~~~~~~~~~~~~~~~~~ THANK YOU ~~~~~~~~~~~~~~~~~~~~~~~~~

You might also like