1 2 3 5 6 7

TOP MENU MENU

OPEN/CLOSE
HDMI

ORDER NO.
STANDBY/ON
ENTER
DVD/USB USB
HOME RETURN
MENU

13 12 9 8 RRV3798
DV-610AV-S

DVD PLAYER

DV-610AV-S
DV-610AV-K
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model Type Power Requirement Region No. Remarks

DV-610AV-S WYXZT5 AC 220 V to 240 V 2

DV-610AV-S WVXZT5 AC 220 V to 240 V 2

DV-610AV-S WSXZT5 AC 220 V to 240 V 5

DV-610AV-K WYXZT5 AC 220 V to 240 V 2

DV-610AV-K WSXZT5 AC 220 V to 240 V 5

For details, refer to "Important Check Points for good servicing".

PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan

PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2008
T-ZZV JUNE 2008 Printed in Japan
 1 2 3 4

SAFETY INFORMATION

A
This service manual is intended for qualified service technicians ; it is not meant for the casual
do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been
trainedto properly and safely repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may
void the warranty. If you are not qualified to perform the repair of this product properly and safely,
you should not risk trying to do so and refer the repair to a qualified service technician.

WARNING !
B THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1
BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR
CLASS 1.
A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS.

LASER DIODE CHARACTERISTICS

FOR DVD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 650 nm
FOR CD : MAXIMUM OUTPUT POWER : 5 mW
WAVELENGTH : 780 nm

LABEL CHECK

Location: inside of the unit

Additional Laser Caution

1.
Laser diode is driving with Q2303,Q2305(650 nm LD) and Q2302,
Q2304(780 nm LD)on the DVD MT PCB Assy.
Therefore, when short-circuit between the emitter and collector of these
transistors or the base voltage is supplied for transistors turn on, the
laser oscillates. (failure mode)
(Printed on the Rear Panel) In the test mode , there is the mode that the laser oscillates except
for the disc judgment and playback. LD ON mode in the test mode
E oscillates with the laser forcibly.

2. When the cover is open, close viewing through the objective lens with
the naked eye will cause exposure to the laser beam.

STAN
DB
Y/O
N

HD
MI
: See page 27.

OP
EN
/CL
OS
E

DV
D/U
SB

US
B

TO
P ME
NU

ME

F
HO NU
MEME
NU EN
TE
R

RE
TU
RN

2 DV-610AV-S
1 2 3 4
5 6 7 8

DV-610AV-S 3
5 6 7 8
 1 2 3 4

CONTENTS
SAFETY INFORMATION ..........................................................................................................................................................2
1. SERVICE PRECAUTIONS ....................................................................................................................................................5
A 1.1 NOTES ON SOLDERING ...............................................................................................................................................5
1.2 WHEN REPLACING DVD DECK ....................................................................................................................................5
1.3 DISC REMOVAL METHOD.............................................................................................................................................6
2. SPECIFICATIONS .................................................................................................................................................................7
2.1 ACCESSORIES ..............................................................................................................................................................7
2.2 SPECIFICATIONS...........................................................................................................................................................8
2.3 DISC/CONTENT FORMAT .............................................................................................................................................9
2.4 PANEL FACILITILES .....................................................................................................................................................11
3. BASIC ITEMS FOR SERVICE.............................................................................................................................................13
3.1 CHECK POINTS AFTER SERVICING..........................................................................................................................13
3.2 PCB LOCATIONS .........................................................................................................................................................14
3.3 JIGS LIST .....................................................................................................................................................................15
B
4. BLOCK DIAGRAM...............................................................................................................................................................16
4.1 OVERALL WIRING DIAGRAM......................................................................................................................................16
4.2 OVERALL BLOCK DIAGRAM.......................................................................................................................................18
4.3 DVD LOADER/MPEG BLOCK DIAGRAM.....................................................................................................................19
4.4 POWER BLOCK DIAGRAM..........................................................................................................................................20
5. DIAGNOSIS.........................................................................................................................................................................21
5.1 TROUBLE SHOOTING .................................................................................................................................................21
5.2 METHOD FOR DIAGNOSING DEGRADATION OF THE LDS ON THE PICKUP ASSY .............................................26
6. SERVICE MODE .................................................................................................................................................................27
6.1 SERVICE MODE PROCEDURE...................................................................................................................................27
6.2 SERVICE MODE IN ......................................................................................................................................................28
C
6.3 DISPLAY SPECIFICATION OF THE SERVICE MODE ................................................................................................29
6.4 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY........................................................................................30
6.5 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE ........................................................................................31
7. DISASSEMBLY....................................................................................................................................................................32
8. EACH SETTING AND ADJUSTMENT ................................................................................................................................37
8.1 RE-WRITE FOR DVD FIRMWAVE ...............................................................................................................................37
9. EXPLODED VIEWS AND PARTS LIST...............................................................................................................................40
9.1 PACKING ......................................................................................................................................................................40
9.2 EXTERIOR SECTION...................................................................................................................................................42
9.3 06 DVD MECHA SECTION...........................................................................................................................................44
10. SCHEMATIC DIAGRAM ....................................................................................................................................................46
10.1 DVD MT PCB ASSY(1/7) ............................................................................................................................................46
D 10.2 DVD MT PCB ASSY(2/7) ............................................................................................................................................48
10.3 DVD MT PCB ASSY(3/7) ............................................................................................................................................50
10.4 DVD MT PCB ASSY(4/7) ............................................................................................................................................52
10.5 DVD MT PCB ASSY(5/7) ............................................................................................................................................54
10.6 DVD MT PCB ASSY(6/7) ............................................................................................................................................56
10.7 DVD MT PCB ASSY(7/7) ............................................................................................................................................58
10.8 OPERATION PCB ASSY ............................................................................................................................................60
10.9 POWER PCB ASSY(1/2) ............................................................................................................................................62
10.10 POWER PCB ASSY(2/2) ..........................................................................................................................................64
10.11 WAVEFORMS ...........................................................................................................................................................66
11. PCB CONNECTION DIAGRAM ........................................................................................................................................68
11.2 DVD MT PCB ASSY....................................................................................................................................................69
E 11.3 OPERATION PCB ASSY ............................................................................................................................................71
11.4 POWER PCB ASSY....................................................................................................................................................72
11.1 LOADING MOTOR and SW ........................................................................................................................................68
12. PCB PARTS LIST ..............................................................................................................................................................74

4 DV-610AV-S
1 2 3 4
 5 6 7 8

1. SERVICE PRECAUTIONS
1.1 NOTES ON SOLDERING
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit. A
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.

Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.

Do NOT use a soldering iron whose tip temperature cannot be controlled.

Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden). B

The following lead-free solders are available as service parts:

Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.

1.2 WHEN REPLACING DVD DECK

WHEN REPLACING DVD DECK C

[ Removing the DVD Deck ]

Before removing Pick Up PCB and DVD PCB connector, short circuit the position shown in Fig. 1 using
a soldering iron. If you remove the DVD Deck with no soldering, the Laser may be damaged.

[ Installing the DVD Deck ]

Remove all the soldering on the short circuit position after the connection of Pick Up PCB and DVD
PCB connector.

NOTE
D
Before your operation, please read PREPARATION OF SERVICING .
Use the Lead Free solder.
Manual soldering conditions
Soldering temperature: 320 20 C
Soldering time: Within 3 seconds
Soldering combination: Sn-3.0Ag-0.5Cu
When Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to prevent the
Flux smoke from it.

Short circuit using a E

soldering iron.

Pick Up PCB

Fig. 1
F

DV-610AV-S 5
5 6 7 8
 1 2 3 4

1.3 DISC REMOVAL METHOD

DISC REMOVAL METHOD AT NO POWER SUPPLY

A
1. Slide the Rack Loading (White) toward the arrow direction by using a minus driver to release the lock.
(Refer to Fig. 1)
2. Manually open the Tray.
NOTE: Please strongly pushing Rack Loading (White) to release the lock because the tray doesn't go out
easily.

DVD Player (Bottom Side)

Rack Loading (White)

Fig. 1

PARENTAL CONTROL - RATING LEVEL

4 DIGIT PASSWORD CANCELLATION
If the stored 4 digit password in the Rating Level menu needs to be cancelled, please follow the steps
below.
D
1. Set the DVD to the Stand-by Mode.
2. Press and hold the 'STOP' key on the front panel.
3. Simultaneously press and hold the POWER key on the front panel.
4. The 4 digit password has now been cleared.

NOTE: The above procedure will reset ALL of the player's settings to the default factory state.

PREPARATION OF SERVICING
E The laser diode used for a pickup head may be destroyed with external static electricity.
Moreover, even if it is operating normally after repair, when static electricity discharge is
received at the time of repair, the life of the product may be shortened.
Please perform the following measure against static electricity, be careful of destruction of a
laser diode at the time of repair.

Place the unit on a workstation equipped to protect against static electricity, such as
conductive mat.
Soldering iron with ground wire or ceramic type is used.
A worker needs to use a ground conductive wrist strap for body.
F

6 DV-610AV-S
1 2 3 4
 5 6 7 8

2. SPECIFICATIONS
2.1 ACCESSORIES
Accessories A

Remote control x1 Power cable x1 Audio / Video cable(1.2m) x1

(076E0PP121:DV-610AV-S) (1206158802 : WYXZT5, WSXZT5) (red/white/yellow)
(076E0PP131:DV-610AV-K) (06CPBA2006)

(1206138802 : WVXZT5)

Warranty Card
Operating Instructions

Dry cell batteries x2

(AA/R6P)

DV-610AV-S 7
5 6 7 8
 1 2 3 4

2.2 SPECIFICATIONS

General Audio output (1 stereo pair)

Power requirements. . . . AC 220 V to 240 V, 50 Hz/60 Hz Output level. . . . . . . . . . . . . . . . . . . .During audio output
Power consumption. . . . . . . . . . . . . . . . . . . . . . . . . .12 W 200 mVrms (1 kHz, 20 dB)
Power consumption (standby) . . . . . . . . . . . . . . . . 0.8 W Number of channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.7 kg Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA
Dimensions
. . . . . . . . . . . 420 mm (W) x 49.5 mm (H) x 215.5 mm (D) Audio output (multi-channel / L, R, C, SW,
Operating temperature . . . . . . . . . . . . . .+5 C to +35 C SL, SR)
Operating humidity . . . . 5 % to 85 % (no condensation)
Output level. . . . . . . . . . . . . . . . . . . .During audio output
AV Connector 200 mVrms (1 kHz, 20 dB)
Number of channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
(21-pin connector assignment) Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA
B AV connector output . . . . . . . . . . . . . . .21-pin connector
This connector provides the video and audio signals for HDMI output
connection to a compatible colour TV or monitor.
HDMI output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19pin

Digital audio characteristics

Frequency response. . . . . . . . . . . . . . . . . . 4 Hz to 44 kHz
S/N ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 dB
Dynamic range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 dB
Total harmonic distortion. . . . . . . . . . . . . . . . . . .0.0023 %
PIN no. Wow and flutter . . . . . . . . . . . . . . Limit of measurement
1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Audio 2/R out (0.001 %W. PEAK) or lower
3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Audio 1/L out
4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND Digital outputs
7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B out
8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Status Coaxial digital output. . . . . . . . . . . . . . . . . . . . . . . . . RCA
C 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .G out Optical digital output . . . . . . . . . . . . . . . . . . . . . . . Optical
15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .R out
17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND Accessories
19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Video out Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND AA/R6P dry cell batteries. . . . . . . . . . . . . . . . . . . . . . . . 2
Audio/video cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Component video output Power cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Y (luminance) - Output level . . . . . . . . . . . . 1 Vp-p (75 ) Warranty card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
PB (color) - Output level. . . . . . . . . . . . . . .0.7 Vp-p (75 ) Operating instructions
PR (color) - Output level. . . . . . . . . . . . . . .0.7 Vp-p (75 )
Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA The specifications and design of this product are subject
to change without notice, due to improvement.
S-video output Published by Pioneer Corporation.
Y (luminance) - Output level . . . . . . . . . . . . 1 Vp-p (75 ) Copyright 2008 Pioneer Corporation.
C (color) - Output level. . . . . . . . . . . . . .286 mVp-p (75 ) All rights reserved.
D Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S-video

Video output
Output level . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p (75 )
Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RCA

8 DV-610AV-S
1 2 3 4
 5 6 7 8

2.3 DISC/CONTENT FORMAT

Disc/content format playback compatibility About DualDisc playback
A DualDisc is a new two -sided disc, one side of which contains DVD
content video, audio, etc. while the other side contains non-DVD A
This player is compatible with a wide range of disc types (media) and
formats. Playable discs will generally feature one of the following content such as digital audio material.
logos on the disc and/or disc packaging. Note however that some The non-DVD, audio side of the disc is not compliant with the CD
disc types, such as recordable CD and DVD, may be in an audio specification and therefore may not play.
unplayable formatsee below for further compatibility information.
The DVD side of a DualDisc plays in this product.
Please also note that recordable discs cannot be recorded
using this player. For more detailed information on the DualDisc specification, please
refer to the disc manufacturer or disc retailer.

CD-R/-RW compatibility
Compatible formats: CD-audio, Video CD/Super VCD, ISO 9660
CD-ROM* containing MP3, WMA, MPEG-4 AAC, JPEG or DivX
video/WMV files
B
*ISO 9660 Level 1 or 2 compliant. CD physical format: Mode1,
Mode2 XA Form1. Romeo and Joliet file systems are both
compatible with this player.
Multi-session playback: No
Unfinalized disc playback: No
File structure (may differ): Up to299 folders on a disc;
up to 648 folders and files (combined) within each folder

DVD+R/+RW compatibility
Only DVD+R/DVD+RW discs recorded in Video Mode (DVD Video
Mode) which have been finalized, can be played back. However,
some editing made during the recording may not be played back C
accurately.

DVD-R/-RW compatibility
This unit will play DVD+R/+RW discs. Compatible formats: DVD-Video, Video Recording (VR)*
* Edit points may not play exactly as edited; screen may go
momentarily blank at edited points.
is a trademark of DVD Format/Logo Licensing
Unfinalized playback: No
Corporation.
MP3/WMA/MPEG-4 AAC/JPEG or DivX video/WMV file playback
is a trademark of FUJIFILM Corporation. on DVD-R/-RW: Yes
Also compatible with KODAK Picture CD
Compressed audio compatibility
This player supports the IECs SuperVCD standard. Compared to Compatible formats: MPEG-1 Audio Layer 3 (MP3), Windows
the VideoCD standard, SuperVCD offers superior picture quality, Media Audio (WMA), MPEG-4 AAC D
and allows two stereo soundtracks to be recorded. SuperVCD also
supports the widescreen size. Sampling rates: 32 kHz, 44.1 kHz or 48 kHz
Bit-rates: Any (128 kbps or higher recommended)
VBR (variable bit rate) MP3/WMA/MPEG-4 AAC playback: No
WMA lossless encoding compatible: No
DRM (Digital Rights Management) compatible: No (DRM-
protected audio files will not play in this player
File extensions: .mp3, .wma, .m4a (these must be used for the
Super VCD player to recognize MP3, WMA and MPEG-4 AAC filesdo not
use for other file types)

DV-610AV-S 9
5 6 7 8
 1 2 3 4

About MPEG-4 AAC DivX video compatibility

Advanced Audio Coding (AAC) is at the core of the MPEG-4 AAC Official DivX Ultra Certified product.
standard, which incorporates MPEG-2 AAC, forming the basis of the
MPEG-4 audio compression technology. The file format and Plays all versions of DivX video (including DivX 6) with
A
extension used depend on the application used to encode the AAC standard playback of DivX media files.
file. This unit plays back AAC files encoded by iTunes bearing the File extensions: .avi and .divx (these must be used for the player
extension .m4a. DRM-protected files will not play, and files to recognize DivX video files).Note that all files with the .avi
encoded with some versions of iTunes may not play, or filenames extension are recognized as MPEG4, but not all of these are
may display incorrectly. necessarily DivX video files and therefore may not be playable
Apple and iTunes are trademarks of Apple Inc., registered in the on this player.
U.S. and other countries.
About Windows Media Video (WMV)
WMA (Windows Media Audio) compatibility WMV is an acronym for Windows Media Video and refers to a video
This player can playback Windows Media Audio content. compression technology developed by Microsoft Corporation. WMV
WMA is an acronym for Windows Media Audio and refers to an content can be encoded by using Windows Media Encoder.

B audio compression technology developed by Microsoft Corporation.

This player is compatible with WMV9 files that are encoded by
WMA content can be encoded by using Windows Media Player for
Windows XP, Windows Media Player 9 or Windows Media Player 10 using the Windows Media Encoder 9 Series, with .wmv as an
series. extension.
TM
Windows Media is a trademark of Microsoft Corporation. Compatible with size under 720 x 480 pixels/720 x 576 pixels.
This product includes technology owned by Microsoft Corporation Advanced Profile is not supported.
and cannot be used or distributed without a license from DRM-protected video files will not play in this player.
Microsoft Licensing, Inc.
JPEG file compatibility
About DivX video Compatible formats: Baseline JPEG and EXIF 2.2* still image
DivX is a digital videoformat created by DivX, Inc. This player can files up to a resolution of 3072 x 2048.
play DiviX videos burned on CD-R/-RW/-ROM discs. Keeping the * File format used by digital still cameras.
C same terminology as DVD-Video, individual DivX video files are Progressive JPEG compatible: No
called Titles. When naming files/titles on a CD-R/-RW disc prior to File extensions: .jpg (must be used for the player to recognize
burning, keep in mind that by default they will be played in JPEG filesdo not use for other file types)
alphabetical order.
PC-created disc compatibility
Discs recorded using a personal computer may not be playable in
This player can play DivX videos recorded on
this unit due to the setting of the application software used to create
DVDs, CDs, or USB storage devices. Keeping
the same terminology as DVD-Video, the disc. In these particular instances, check with the software
individual DivX video files are called Titles. publisher for more detailed information.
DivX videos will be played in alphabetical Discs recorded in packet write mode (UDF format) are not
order. compatible with this player.
Check the DVD-R/-RW or CD-R/-RW software disc boxes for
D additional compatibility information.

DivX, DivX Ultra Certified, and associated

logos are trademarks of DivX, Inc. and are
used under license.

10 DV-610AV-S
1 2 3 4
 5 6 7 8

2.4 PANEL FACILITILES

Front panel
A
1 2 3 4 5 6 7
TOP MENU MENU
OPEN/CLOSE
HDMI
STANDBY/ON
ENTER
DVD/USB USB
HOME
MENU RETURN

16 15 14 13 12 11 10 9 8

B
1 STANDBY/ON 16 HDMI indicator
Press to switch the player on or into standby. Lights when this player is recognized by
another HDMl or DVI/HDCP compatible
2 Disc tray component.

3 OPEN/CLOSE
Press to open or close the disc tray.

4 Display

5 TOP MENU
Displays the top menu of a DVD disc
this varies with the disc. C

6 ENTER & cursor buttons

Selects the current menu option.

7 MENU
Displays a DVD disc (or DiviX media files) menu
this varies with the disc and may be the same
as the top menu.

8 RETURN
Returns to the previously displayed menu screen.

9 HOME MENU D

Display/exit the on-screen display.

10 USB port (Type A)

11 DVD/USB
Press to turn to USB mode and return to DVD mode.

12
Press to start or resume playback.

13
Press to pause playback. Press again to E
restart.
14
Press to stop the disc (you can resume play-
back by pressing (play)).

15 and
Skips to the start of the current track, title or
chapter, then to previous tracks/titles/chapters.
Skips to the next track, title or chapter.

DV-610AV-S 11
5 6 7 8
 1 2 3 4

Remote control
Press to start or resume playback.

A
Skips to the start of the current track, title or
chapter, then to previous tracks/titles/chapters.

Press to pause playback; press again to

restart.

12 USB REC
Press to enter to the USB REC screen.

13 PLAY MODE
Press to display the Play Mode menu. (You
B can also get to the Play Mode menu by
pressing HOME MENU and selecting Play
Mode).
Press to jump to the beginning of the current

Press to open or close the disc tray.

15 ANGLE
Press to change the camera angle during
DVD multi-angle scene playback.

C 16 DVD/USB
Press to turn to USB mode and return to DVD
mode.
17 CLEAR
Press to clear a numeric entry.

18 MENU
Displays a DVD disc (or DiviX media files) menu
this varies with the disc and may be the same
as the top menu.

Press to switch the player on or into standby. 19 RETURN

D Press to return to a previous menu screen.
2 AUDIO
Press to select the audio channel or language.
Use for forward slow motion playback, frame
3 SUBTITLE advance and forward scanning.
Press to select a subtitle option.

4 Number buttons Press to jump to the next chapter or track.

5 TOP MENU
Press to display the top menu of a DVD disc.

6 ENTER & cursor buttons

Use to navigate on-screen displays and
23 DISPLAY
E
menus. Press ENTER to select an option or Press to display information about the disc
execute a command. playing.

24 ZOOM
7 HOME MENU
Display/exit the on-screen display. Press to change the zoom level.

and
Use for reverse slow motion playback, frame
reverse and reverse scanning.

12 DV-610AV-S
1 2 3 4
 5 6 7 8

3. BASIC ITEMS FOR SERVICE

3.1 CHECK POINTS AFTER SERVICING
Check points after servicing (DVD player) A

To keep the product quality after servicing, confirm recommended check points shown below.

No. Procedure Check points

1 Confirm the firmware version on Service Mode. The version of the firmware must be latest.
Update firmware to the latest one, if it is not the latest.
Confirm whether the customer complain has been solved. The customer complain must not be reappeared.
2 If the customer complain occurs with the specific disc, Video, audio and operations must be normal.
use it for the operation check.
Confirm playback error rates at the innermost and The error rates must be less than 5.0e-4.
3 outermost tracks by using the following disc. B
DVD test disc (GGV1025)
Play back a DVD. Audio and operations must be normal.
4
(Menu operation, Title/chapter search)
Play back a DVD. Video, audio and operations must be normal.
5
(Menu operation, Title/chapter search)
Check the appearance of the product. No scratches or dirt on its appearance after receiving it
6
for service.

See the table below for the items to be checked regarding video and audio: C

Items to be checked regarding video Item to be checked regarding audio

Block noise Distortion
Horizontal noise Noise
Dot noise Volume too low
Disturbed image (video jumpiness) Volume too high
Too dark Volume fluctuating
Too bright Sound interrupted
D
Mottled color

Cleaning
Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools:
Position to be cleaned Cleaning tools Remark
Pickup lenses Cleaning liquid : GEM1004
E
Cleaning paper : GED-008

DV-610AV-S 13
5 6 7 8
 1 2 3 4

3.2 PCB LOCATIONS

POWER PCB ASSY

DVD MECHA ASSY

B DVD MT PCB ASSY

OPERATION PCB ASSY

Mark No. Description Part No.

LIST OF ASSEMBLIES
1..DVD MT PCB ASSY A2L502A130

1..OPERATION PCB ASSY A2L502A270

(WYXZT5,WVXZT5)

1..OPERATION PCB ASSY A2L506A270

(WSXZT5)
E
> 1..POWER PCB ASSY A2L502A240

1..DVD MECHA ASSY A2L101A650

14 DV-610AV-S
1 2 3 4
 5 6 7 8

3.3 JIGS LIST

Jigs list
A
Name Jig No. Remarks
Service Remote Control Unit GGF1381 diagnosis
DVD Test Disc (DVD-Video,NTSC) GGV1025 Operation Check
DVD Test Disc (DVD-Video,PAL) GGV1101 Operation Check
CD Test Disc STD-905 Operation Check

Lubricants and Glues list

B
Name Lubricants and Glues No. Remark
Daifree GEM1036 (ZLX-ME413A) Refer to "9.3 DVD MECHA SECTION"
Grease GYA1001 (ZLB-PN397B) Refer to "9.3 DVD MECHA SECTION"
Grease GEM1018 Refer to "9.3 DVD MECHA SECTION"

DV-610AV-S 15
5 6 7 8
 1 2 3 4

4. BLOCK DIAGRAM
4.1 OVERALL WIRING DIAGRAM
A

INTERCONNECTION D
E E E
CP502 CP4003_1 1 4 1
CD502 6 5
GND 1 1 1 1 GND
AC120V_60Hz(US)
CD501 P.CON+12V 2 2 2 2 P.CON+12V 3 2 6 5 3 2
CONNECTOR H2 H1 H2 H1 2 1 H2
BLADE
WIDE
3 3 3 3 J7302
N CP501 4 3
GND 4 4 4 4 GND CVBS/Y/U/V LS/R

2
WHITE P.CON+5V 5 5 P.CON+5V J7304
5 5
P.CON+6V 6 6 P.CON+6V S-VIDEO OUT for HE
6 6
1

1
BLACK GND(M) 7 7 7 7 GND(M)
L AT+3.3V 8 8 AT+3.3V
8 8
AT+3.3V 9 9 9 9 AT+3.3V
P.ON-H(STBY L) 10 10 10 10 P.ON-H(STBY L) DVD MT PCB ASSY
B GND(D)
FL DC-
11
12
11 11 11
12
GND(D)
FL DC-
(1/7 - 7/7)
FL DC+ 13
12
13
12
13 13 FL DC+ (A2L502A130)
-28V 14 14 14 14 -28V
GND(USB) 15 15 15 15 GND(USB)
USB+5V 16 16 16 16 USB+5V HDMI CONNECTOR
CP5901
1 D2+
CP8102 CP8001 2 D2-S
3 DVD MT PCB
SPDIF 1 1 1 1 SPDIF D2- PCB130
GND 2 2 2 2 GND 4 D1+ DMG100
5 D1-S
OPTICAL 6 D1-
OS8101 7
COAXIAL D0+
J8102 1 INPUT 8 D0-S
POWER PCB
2 VCC PCB240 9
H

D0-
DPG017
2

3 GND 10 CLK+
C 11 CLK-S
12
POWER PCB ASSY 13
CLK-
CEC NC
(1/2,2/2) 14 NC
NC
15
(A2L502A240) 16
SCL
SDA
17 GND
18 POWER
19 HOTPLUG

DO (F to M)

DI (M to F)
GND(USB)
USB+5V

FLDC+
FLDC-

DGND
DGND
USBN
USBP

V+3E
-28V

STB

CLK
IR

OPERATION
CP4004

CP4002
PCB ASSY
11
10
4
3
2
1

9
8
7
6
5
4
3
2
1

(WYXZT5,WVXZT5:A2L502A270)
4
3
2
1

11
10
9
8
7
6
5
4
3
2
1

(WSXZT5:A2L506A270)
CD605

CD601
11
10
9
8
7
6
5
4
3
2
1
4
3
2
1
CP602
USB CONNECTOR

CP605

CP601
11
10
4
3
2
1

4
3
2
1

9
8
7
6
5
4
3
2
1

CP603 CP604
GND 1 1 1 1 GND
DO (F to M)

DI (M to F)
GND(USB)

E
USB_DN
USB_DP

USB+5V

FLDC+

SW2 2
FLDC-

DGND
DGND
USBN
USBP

V+3E

2 2 2 SW2
-28V
GND

STB

CLK
+5V

IR

POWER 3 3 3 3 POWER
OPERATION2 PCB

OPERATION PCB
DEG150
PCB271

DEG149
PCB270

1 Vout
2 GND
3 B+

OS651

F
CAUTION:SINCE THESE PARTS MARKED BY ARE ATTENTION:LES PIECES REPAREES PAR UN ETA
CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SEC
DESCRIBED IN PARTS LIST ONLY. N'UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES

16 DV-610AV-S
1 2 3 4
 5 6 7 8

ECTION DIAGRAM
E E

H2 H1
1 4

2
6 5

3
3 2 6 5
2 1 H2 H1 H2 H1 J8001
J8002 L/R CP2301
4 3
LS/RS/C/LFE FOCS RTN 24 24 24 FOCS RTN
J7304
DEO OUT for HE
FOCS DRV 23 23 23 FOCS DRV
TRKG RTN 22 22 22 TRKG RTN
TRKG DRV 21 21 21 TRKG DRV
NC 20 20 20 NC
DVD
B ASSY GND 19 19 19 GND DRIVE
LD_DVD(650) 18 18 18 LD_DVD(650) DM-4PB B
PD/GND 17 17 17 PD/GND
30) LD_CD(780) 16 16 16 LD_CD(780)
GND 15 15 15 GND
VR780(CD) 14 14 14 VR780(CD)
VRCOM 13 13 13 VRCOM
VR650(DVD) 12 12 12 VR650(DVD)
A 11 11 11 A
DVD MT PCB
PCB130 B 10 10 10 B
OPTICAL PICK-UP
DMG100 VRF(RF_OUT) 9 9 9 VRF(RF_OUT)
SW1(DVD/CD) 8 8 8 SW1(DVD/CD)
C 7 7 7 C
D 6 6 6 D
E 5 5 5 E
VCC 4 4 4 VCC
VS 3 3 3 VS C
F 2 2 2 F
GND 1 1 1 GND (SW PCB)
PCB640
DED020

SW2
CD2301 ESE22MH22
CP2303 2H061605
SW(GND) 6 6 1 1 GND(SW)
LIMIT SW 5 5 2 2 PICK UO INNER LIMIT SWITCH
SLD- 4 4 3 3 FEED MOTOR(-) M M2602
SLD+ 3 3 4 4 FEED MOTOR(+) BCZ3B05
SPD- 2 2 5 5 SPINDLE MOTOR(-)
6 SPINDLE MOTOR(+) M2601
SPD+ 1 1 6 M JCV9B12
D
CD2302
CP2302 2H051602
M2603
LOAD- 5 1 LOADING MOTOR(-) M BCZ3B05
LOAD+ 4 2 LOADING MOTOR(-)
DI (M to F)

OPEN 3 3 SW-1(OPEN)
SW1
CLK

GND 2 4 GND(SW)
SSS-28-5
5 SW-2(CLOSE)
CP4002

CLOSE 1

PCB610
2
1

DED021
2
1
CD601

(LOADING MOTOR PCB)

2
1
CP601
2
1

DVD MECHA ASSY

DI (M to F)

E
(A2L101A650)
CLK

F
REPAREES PAR UN ETANT NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS
SES AN POINT DE VUE SECURITE OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. MEASURED WITH THE DIGITAL TESTER
QUE CELLS DECRITES DURING PLAYBACK.
MENCLATURE DES PIECES.

DV-610AV-S 17
5 6 7 8
 F
E
B
A

D
C

18
1
1

OVERALL BLOCK DIAGRAM SR

SL

LFE

RESET IC 4K EEPROM IC8003/4/5 IC8002/7/8

IC4003 IC4001 AUDIO DAC IC R
AUDIO LPF AND AMP IC
R3112N291A-TR- S-24CS04AFJ-TB- PCM1742KE/2K RC4580IDR L
FA GE

21 PIN
FIP
HNV-08SS84 DAC_XCSO, SCK, SD, CVBS OUT
SDA, SCL ACLK, ABCK, ALRCK,
RGB OUT

RESET
KEY ASDAT0~2

2
2

27MHz

MPEG/MICON BLOCK CVBS

4.2 OVERALL BLOCK DIAGRAM

FIP DRIVER IC IC4002 AMUTE

FP,STB AUDIO CODEC/ Y
IC651 MT1389EXE/S-L 4CH BUS SW IC
INTERNAL DAC
PT6315 IC7302 U
SN74CBT3257PWR
V

IR MPEG-1/2/ S_Y
IR

DV-610AV-S
RF JPEG 108MHz 4CH VIDEO DAC VIDEO DRIVER 6CH IC
SERVO IC7301
VIDEO TV Encoder S_C
IR RECEIVER (OS651) DECORDER LA73054-TLM-E
KSM-2001TC2P
ASPDIF COAXIAL
CO

3
3

MOTOR DRIVER TX0+/-,

IC2301 RF LD_DVD, A0~A20, MA0~MA11, TX1+/-, OPTICAL
AM5766 LD_CD AD0~AD7 DQ0~DQ15 TX2+/-, OP
TXC+/-

SERVO
16Mbit FLASH 64Mbit SDRAM HDMI
IC4004 IC4005 CONNECTOR
ES29LV160EB-70TG M12L64164A-5TG CP5901
DVD LOADER
(DM4)

P.CON+12V
POWER P.CON+5V
SUPPLY
P.CON+6V
+1.8V

4
4

AT+3.3V
AT+12V for mute
-28V
AC120V V+5H
FLDC+/-
 DVD LOADER/MPEG BLOCK DIAGRAM
5

5
S-VIDEO JACK
LETTER, I/XP, S_Y, S_C, J7304
R/CR, B/CB, G/Y, CVBS ASP
DVD C RESET IC VIDEO DRIVER 6CH IC 3 Y
Loader SQUEEZE, VSEL1
IC4003 IC7301
(DM-4) A 4 C
IOA, V20 R3112N291A- LA73054-TLM-E
TR-FA C CVBS/Y/U/V
J7302
RF, A, B, C, D, E, F, MDI1 X4001
A, B 6 CVBS
27MHz

RESET
A 5 Y

Y OUT
CB OUT
OPU

CR OUT
3 U
LD_DVD, LD_CD LDO1, LDO2 VSEL1 2 V
Q2302~2305 4CH BUS SW IC
LD DRIVE IC7302 21PIN CONNECTOR
T+/-, F+/-, DMSO, FMSO,
D SN74CBT3257PWR J8101
LOAD+/-,
D TROPEN, TRCLOSE,
MOT_SLED+/-, TRSO, FOSO, 19 CVBS
MOT_SPDL+/- MOTOR DRIVER IC STBY, V1P4 15 R OUT
SPINDLE/
STEPING/ IC2301 11 G OUT
AM5766
6

6
SLED MPEG/MICON IC 7 B OUT
MOTOR LIMIT, TRIN, TROUT, Q8101, Q8102 21 PIN CTL
IC4002 8
SQUEEZE BLANKING_OUT
OPO, OP+/- MT1389EXE/S-L 21 PIN CTL 16
A0~A20, AD0~AD7, Q8104, Q8105 3 L
PRD#, PCE#, PWR# VSEL1 1 R
DVD_RGB_H_OUT
MA0~MA11, DQ0~DQ15, L/R JACK
DQM0, DQM1, DBA0, DBA1, SDC J8001
IC8002/7/8
LK, SDCKE, DWE#, F 2 R
AUDIO LPF AND AMP IC
DRAS#, DCAS#, DCS# 3 L
RC4580IDR
A LS/RS/S/LFE JACK
J8002

DV-610AV-S
4.3 DVD LOADER/MPEG BLOCK DIAGRAM

16Mbit FLASH 64Mbit SDRAM SDA 2 SR

EEPROM IC IC8003/4/5
A IC4004 IC4005 A IC4001 SCL A, C AUDIO DAC IC 3 SL
ES29LV160EB-70TG M12L64164A-5TG
S-24CS04AFJ-TB- PCM1742KE/2K 5 LFE
GE C
6
DAC_XCSO, SCK, SD,
7

7
COAXIAL JACK
ACLK, ABCK, ALRCK, J8102
ASDAT0~2 COAXIAL
HDMI CONNECTOR 2
L5902
CP5901 5 ASPDIF OPTICAL
1 D2+ 4 6 OS8001
OPTICAL
3 D2- 3 IR RECEIVER (OS651)
7 1
KSM-2001TC2P
4 D1+ 2 8
L5901
6 D1- 1 IR A.......AT+3.3V
5 IR A
7 D0+ 4 6 B.......+1.8V
FP_DI, FP_DO, C.......P.CON+5V
9 D0- 3
7 FP_SCK, STB D.......P.CON+6V
FIP DRIVER IC GR1~GR8, P1~P16
10 CLK+ 2 8 FIP (V651) E.......AT+12V
IC651 HNV-08SS84 F.......P.CON+12V
12 CLK- 1 A PT6315 G
G.......-28V
19 HOTPLUG H.......V+5H
18 POWER
8

8
15 SCL
Q5906
16 SDA
USB_FLAG
HIGH SIDE SW IC
USB_P_ON-L IC4007
R5523N001B-TR-F

19
F
E
B
A

D
C
 F
E
B
A

D
C

20
POWER BLOCK DIAGRAM

1
1

PHOTO COUPLER
IC504 VOLTAGE CTL
PS2561AL1-1-V(W) IC501
KIA431A-AT

REG+1.8V
POWER CTL IC4006
IC502 LD1117AL-ADJ-AA3 +1.8V
STR-A6159M

2
-A-R
2

4.4 POWER BLOCK DIAGRAM

AT+12V for mute

Q510
P.CON +12V SW P.CON+12V
Q515
P.CON +5V SW P.CON+5V

DV-610AV-S
SWITCHING 6V REG P.CON+6V
AC IN TRANS IC503
T501 PQ070XF01SZH
HDMI+5V REG IC

3
3

IC5902 V+5H
PQ1K503M2ZPH
Q505
P.CON SW P.ON-H

AT+3.3V
FL DC -

Q504
FL+ P.CON SW FL DC +

Q502

4
4

-28V P.CON SW -28V

 5 6 7 8

5. DIAGNOSIS
5.1 TROUBLE SHOOTING
A

POWER DOES NOT TURN ON

Is the voltage at No
pin 8 and pin 9 of CP502 about 3.3 V Check AT+3.3V line of POWER BLOCK.
and at pin 5 of CP502 Check Q515 and peripheral circuit.
about 5 V? B

Yes

Is there waveform at No Check X4001, IC4002 and

X4001 about 3.0 Vp-p ? peripheral circuit.

Yes
C

Write DVD FIRMWARE DATA.

DECK DOES NOT ACCEPT

OPEN/CLOSE
D

Is the voltage at No Check P.CON 6V line of

pin 8 and 19 of IC2301
about DC 6 V ? POWER BLOCK.

Yes

Is the lose connection Yes Check CD2302

at CD2302 to DECK ? connection to DECK.

No

Change DVD LOADER.

DV-610AV-S 21
5 6 7 8
 1 2 3 4

A
DOES NOT LIGHT ON DISPLAY

Is the voltage at No Check AT+3.3V line of

pin 13 and pin 43 of IC651
about 3 V ? POWER BLOCK.

B Yes

Replace V651 or IC651.

NO PLAYBACK PICTURE OF AV
C JACK

Is there No Check IC4002 and

a signal at pin 187 of
IC4002 ? peripheral circuit.

Yes

Is there Yes Check J7302 and peripheral

video signal at pin 33
of IC7301 ? circuit.

No

Change IC7301.

22 DV-610AV-S
1 2 3 4
 5 6 7 8

NO DIGITAL AUDIO ON
A
PLAYBACK OF COAXIAL JACK

Is there Yes Check connection at RCA

waveform at pin 2 of J8102
about 0.5Vp-p? Cable.

No

Is there Yes Check Q8103 and

waveform at pin 215 of IC4002
about 3.3 Vp-p ? peripheral circuit.

No

Change IC4002.
C

NO ANALOG AUDIO ON
PLAYBACK

D
Yes
Is there Check J8001 and peripheral
AUDIO signal at pins 7 and 8
of IC8003 ? circuit.

No

Is there waveform at Yes Is there voltage at No

pins 1,2 and 3 of pin 6 of IC8003 about 5 V ? Check AT+5V E
IC8003 ?

No Yes

Change IC4002. Change IC8003.

DV-610AV-S 23
5 6 7 8
 1 2 3 4

A NO 5.1CH AUDIO ON
PLAYBACK

Is there AUDIO signal at Yes Check J8001, J8002 and

pins 7 and 8 of IC8003, peripheral circuit.
IC8004 and IC8005 ?

No
B

Is there waveform at Yes Is there voltage at pin 6 No

pins 1, 2 and 3 of IC8003, of IC8003, IC8004 and Check AT+5V.
IC8004 and IC8005 ? IC8005 about 5 V ?

No
Yes

Change IC8003,
Change IC4002. IC8004 and IC8005.

D NO OPTICAL OUT

No
Is there voltage at pin Check P.CON +D5V line.
2 of OS8101 about 5 V?

Yes

Yes REFER TO "NO DIGITAL

Is the waveform at pin 1
of OS8101 about 2.5 V ? AUDIO ON PLAYBACK OF
COXIAL JACK"
No

Change OS8101.

24 DV-610AV-S
1 2 3 4
 5 6 7 8

A
Symptoms That May Occur When Any Of The Following ICs Is In Failure
IC Symptoms
EEPROM User's data cannot be stored in memory.
(DVD MT PCB Assy : IC4001) The ID number is lost.

16M Flash ROM The power cannot be turned on.

(DVD MT PCB Assy : IC4004) Downloading of the firmware cannot be performed.

DVD IC Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be
(DVD MT PCB Assy : IC4002) generated, because the DVD processing is performed by a single chip.

64M SDRAM No power. B

(DVD MT PCB Assy : IC4005) Block noise is generated during playback.

DV-610AV-S 25
5 6 7 8
 1 2 3 4

5.2 METHOD FOR DIAGNOSING DEGRADATION OF THE LDS ON THE PICKUP ASSY
Case when this diagnosis is required :
A
When playback of any disc, including a test disc (DVD: GGV1025, CD: STD-905), cannot be performed

How to diagnose
In the case mentioned above, degradation of the laser diodes (LDs) mounted on the PICKUP Assy is suspected.
Measure the voltage between the two ends of one of the resistors mentioned below.

No playback of a DVD :
Measure the voltage between the two ends of NR2301 on the DVD MT PCB Assy.
If the voltage is 0.17 V or higher, the 650-nm LD is degraded.
B
If the measurements show degradation
of an LD, replace the PICKUP Assy.
No playback of a CD :
Measure the voltage between the two ends of NR2301 on the DVD MT PCB Assy.
If the voltage is 0.20 V or higher, the 780-nm LD is degraded.

DVD MT PCB ASSY

C404

C404

R4004
R4014

C4052
C4131

C4101
C4120
R4044

C4022

C5920
C4040

W840

C5921
Q5906
R4051

R4001
C4055

C4064

W862
W813

D7309
Q4004

C4054
C4051
B4014

C4021

C4025

C4088 C4073
C4037 C4012

C4072
R4054

D7312
C4029

C4016 C4013 C4020 R4039

R4060 B4018
C4015 C4019 C4005 C4075

B7304
C4036
C4030

R4009 W856
C4081 C4068
W822
W848

R4034
R4021
W821

W851
W858
W850

W820

C4071 C4082

R4003
W804

C5901
Q4002

D7311
D7307
D7308
W844

C4130

R7321
D4005

R7305
C4080
W816
C4008
C4009

W864
D7310
R4005
C4105

B4015
R4020 C4017
C4026
C4027

C4014
R4064

B4016
NR4003
R4065

C7313
R4067
R4068
R4069
C4083
R4048

R4008 C4065 C4074

R4026

R4066
R4058
R4022 C4028

C4043
C4033

C4046

C4110 R4061
C4084

C4067 R4002

C7302 C7317
C4061
R7304
C4041
C4034
C4035

C7330
C4066
R4006
R7317

C7305
W832

W807
C4048

C4049

R7315
C4128
Q7302

B7301

R7316
W819

C8057

R8058

W868
R8055
R4050
B4014

Q8017

R8077
R8054
C8052

R8076
R4040

W822
DMG100A

R8048

C8056
W804

R8031

R8052
R8069

R8067
R8045 C8059 C8049
C8044

D NR2301 R8053

C8063
R4058 Q8020

R8050
R8093
R8012

R8036
D8003 D8006
W832

D8005 R8003

R8046
R8017
R8006

R8092 R8068
C8009 R8072
C8053
Q8010
C4086

C8010
R8021
W845

C8030
W878 Q8008
R8064 R8063
C8013

Q8009

R8074
C8051
C2303
C2302

DMG100A R8002 Q8015

C8055
C8039

NR2301 R8066
R8025 Q8019 Q8021
R8059

R8096 R8099
C8005 C8006
C4086

B8001 R8020
R8082
R8087
R8075
W845

R8061

C8062
C8054

R8065
C2303
C2302

C8025

C8046

26 DV-610AV-S
1 2 3 4
 5 6 7 8

6. SERVICE MODE
6.1 SERVICE MODE PROCEDURE
A

POWER ON

POWER

ON

DISC SET
<TRAY OPEN> <TRAY CLOSE>

OPEN/CLOSE DVD disc OPEN/CLOSE

(Player) (Player)
C

SERVICE MODE: PLAY

CHECK
<PLAY> DVD, CD An address is displayed
ESC TEST D
Press the play key
( ) of the normal
remote control unit.

GGF1381
Service mode DSC -
remote control
unit

Notes:
After going into service mode, if you play back the disc, "DISC-NON" is displayed.
The video signal and the audio signal are outputted during the servicemode.
E
The SKIP key and the SCAN key are effective during the service mode.

SERVICE MODE: OFF

ESC

POWER
OR
GGF1381
Service mode F
OFF remote control
unit

DV-610AV-S 27
5 6 7 8
 1 2 3 4

6.2 SERVICE MODE IN

Service Mode Functional Specification
A  Service mode entry
In the power ON state, press the [ESC] (A8-5F) key and [TEST / RANDOM] (A8-5E) key in order of the Service mode
remote control
unit.
Light the all FL and LEDs.
OSD displays test mode.

Note:
* When pressing the keys of something, the FL displays "NO DISC" and the LED lighting disappears.

 Release the Service mode

B Turn off the power.
Press the [ESC] (A8-5F) key of the remote control unit.

 LD ON
DVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650n).
CD : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n).

28 DV-610AV-S
1 2 3 4
 5 6 7 8

6.3 DISPLAY SPECIFICATION OF THE SERVICE MODE

A
Character in bold : Item name 2
: Information display 3

1 7
8
5 9
6
12 13
14
15

10 B

11

 Address indication RGB : [02]

The address being traced is displayed in number.
(as for the DVD, indication of decimal number is
Disc sensing [DSC ]
possible.) The type of discs loaded is displayed.
DVD : ID indication (hexadecimal number, 8 digits) [DVD], [CD ], [VCD], [ ]
[ ] C
CD : ID indication [ ]
 Jitter value [J ] Note:Don't use it.
 Code indication of remote control unit [R ]
In case of double code, display a 2nd code.  Version of the FL controller [FL: ]

 Main unit keycode indication [K ] Region setting of the player [REG: ]

Setting value : [1] to [6]
 Tracking status [TRKG ]
Tracking on : [ON]  Destination setting of the FL controller
Tracking off : [OFF] [MDL: / ]
Four characters in the front represent code 01.
 Spindle status [SPDL ] Three characters in the back represent the destination D

[OFF], [CLV] code.

J: /J, K: /KU, /KC, /KU/KC, R: /RL/RD, RAM : /RAM,
 Mechanism (loading) position value [M ] LB: /LB, WY: /WY
Unknown : [01] or [41]
Open state : [04]  Version of the flash ROM [VERSION: ]
Close state : [08]
During opening : [12]
During closing : [22]

 Slider position [S ]
In Side Switch ON : [01] E
In Side Switch OFF : [00]

Output video system [V ]

NTSC system : [NTSC]
PAL system : [PAL]
Automatic setting: [AUTO]
Scart terminal output [SK ]
(Display only the WY model which can do the output
setting
of scart terminal.)
VIDEO : [00]
S-VIDEO : [01] F

DV-610AV-S 29
5 6 7 8
 1 2 3 4

6.4 FUNCTIONAL SPECIFICATION OF THE SHORTCUT KEY

Only during normal playback, the following shortcut keys can be assigned by pressing a required key after pressing the ESC
key of the remote control unit. To quit, press the ESC key
A
Remote Control Remote
Command Contents Conditions Key Name ControlCode
Memory clear and region / revision indication CLEAR (1) A8-45
Average value measurement of DVD error rate 5 (1) A8-05
CD error rate measurement 5 (1) A8-05
Scart terminal output : VIDEO AUDIO AF-BE
Scart terminal output : S-VIDEO WY, models equipped with Scart terminal SUBTITLE AF-36
Scart terminal output : RGB ANGLE AF-B5
Progressive OFF R_SKIP A3-9D
Only for progressive models
Progressive ON F_SKIP A3-9C
B ZOOM ON (X2 -> X4 -> x1) ZOOM AF-37
Service mode indication (error rate indication, etc.) CHP/TIM (1) A8-13
Model information indication CHAP (1) A8-40
Title search Input mode IN SIDE A (1) A8-4D
Title No. input Numbers (1) A8-00 to A8-09
Search execution PLAY (1) A8-17
A.MON (1) A8-1E
Region confimation mode
Numbers (1) A8-01 to A8-08
1 : Service mode remote control unit

C Service mode indication (ESC + CHP/TIM keys)

ID Address
The error rate is always displayed in exponential notation, e.g., . e - , for both DVDs and CDs.
EDC/ID/AV 1 error history (ID Address, EDC/ID Error, last eight errors)

Calculation of the average error rate (ESC + "5" [Service mode remote control unit] keys)
The average of the last eight error rates is calculated and indicated in exponential notation. After the calculation is completed, "OK" or "NG" is
displayed. If "NG" is displayed, the disc tray will open (for both DVDs and CDs)
For DVDs: OK with 5.0e-4 or less, for CDs: OK with 7.6e-3 or less

Indication of model information (ESC + CHAP keys)

The items from 12 to 15 of the SERVICE MODE Indications are displayed. However, in the indications, S in the standard test mode is changed
to CHIP VERSION, and M is changed to FL VERSION.
D
Region confirmation mode (ESC + A.MON [Service mode remote control unit] + "1"-"8" [Service mode remote control unit] keys)
After you press the A.MON key while holding the ESC key pressed and then input the region number, if the number is different from that set in
the unit, an error message is displayed, and the tray opens.

30 DV-610AV-S
1 2 3 4
 5 6 7 8

6.5 FUNCTIONAL SPECIFICATION OF THE SERVICE MODE

Display during Service Mode
To enter Service Mode, press the CHP/TIM key while holding the ESC key pressed.
To quit, press the ESC key. A

Service mode display

1 ID Address
2 Error rate (always displayed), in exponential notation
ERROR RATE :
()

Number of error

Calculation of the average error rate

For DVDs: OK with 5.0e-4 or less, for CDs: OK with 7.6e-3 or less
B
ex) For DVDs

Step 1 Step 2
e- e -4

e -6 : OK 3.0e -4 : OK
e -5 : OK 4.0e -4 : OK
e -4 : Refer to Step 2 5.0e -4 : OK
e -3 : NG 6.0e -4 : NG
e -2 : NG 7.0e -4 : NG

3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors)

Note:
Error of AV1 is not supported in this player.

Indication plan contents

3
1
2 D

Character in bold : Item name

: Information display
E

DV-610AV-S 31
5 6 7 8
 1 2 3 4

7. DISASSEMBLY
1. REMOVAL OF MECHANICAL PARTS 1-3: DVD DECK (Refer to Fig. 1-3)
A
AND P.C. BOARDS 1. Short circuit the position shown in Fig. 1-3 using a
soldering iron. If you remove the DVD Deck with no
CAUTION soldering, the Laser may be damaged.
Be careful not to remove the FFC cable forcibly, because 2. Disconnect the following connectors:
the FFC cable may be damaged. (CP2301, CP2302 and CP2303).
3. Remove the 4 screws (1).
4. Remove the DVD Deck in the direction of arrow.
1-1: TOP CABINET/FRONT CABINET AND OPERATION
(Refer to Fig. 1-1) Short circuit using a
(1) soldering iron.
1. Remove the 5 screws (1).
(1)
2. Remove the Top Cabinet in the direction of arrow (A). (1)
B 3. Disconnect the following connectors: (CP4002 and
CP4004). DVD Deck
4. Unlock the 4 supports (2). (1)
5. Remove the Front Cabinet in the direction of arrow (B).
6. Remove the 11 screws (3).
7. Remove the Operation PCB in the direction of arrow (C). Pick Up PCB

Top Cabinet
(1)

(1) (1)

C
(1)
Fig. 1-3
Operation PCB (A)
NOTE
(3)
(1) 1. Before your operation, please read PREPARATION OF
(3) (B)
(3)
SERVICING.
(2) (C)
(3) (3)
2. Use the Lead Free solder.
(3) 3. Manual soldering conditions
(2) (C)
(3) Soldering temperature: 320 20 C
(2) Soldering time: Within 3 seconds
Front Cabinet (2)
Soldering combination: Sn-3.0Ag-0.5Cu
Operation PCB 4. When Soldering/Removing of solder, use the drawing
Fig. 1-1
equipment over the Pick Up Unit to keep the Flux smoke
D away from it.
1-2: POWER PCB (Refer to Fig. 1-2)
5. When installing the DVD Deck, remove all the soldering
1. Disconnect the following connectors: on the short circuit position after the connection of Pick Up
(CP502 and CP8001). PCB and DVD MT PCB connector.
2. Remove the 4 screws (1).
3. Remove the 3 screws (2). 1-4: DVD MT PCB (Refer to Fig. 1-4)
4. Remove the Power PCB in the direction of arrow. 1. Remove the 5 screws (1).
2. Remove the 4 screws (2).
(2)
(2) 3. Remove the DVD MT PCB in the direction of arrow.

(2) (2)
(2) Power PCB
(2)
E
DVD MT PCB
(2)
(1) (1)
(1)
(1)
(1) (1)
(1)
(1)
(1)

Fig. 1-2 Fig. 1-4

F

32 DV-610AV-S
1 2 3 4
 5 6 7 8

2. REMOVAL OF DVD DECK PARTS NOTE

NOTE 1. In case of the Traverse Ass'y, install it from (1) to (4) in

order. (Refer to Fig. 2-2-B)
1. Disassemble only the DVD DECK PARTS parts listed 2. In case of the Traverse Ass'y installation, hook the wire A
here. Minute adjustments are needed if the disassembly on the Loader Ass'y as shown Fig. 2-2-C.
is done. If the repair is needed except listed parts,
replace the DVD MECHA ASS'Y. Loader Ass'y (Bottom Side)

2-1: TRAY (Refer to Fig. 2-1-A)

1. Set the Tray opened. (Refer to the DISC REMOVAL
METHOD AT NO POWER SUPPLY)
Rack Loading
2. Unlock the 2 supports  and draw it while sagging the
Tray.
Holder Traverse

Loader Ass'y

Push to Sag 
Traverse Ass'y

Tray

Push to Sag

Fig. 2-1-A Check Lock Fig. 2-2-B

NOTE
Loader Ass'y C
1. In case of the Tray installation, install them as the circled
section of Fig. 2-1-B so that the each markers are met.

Loader Ass'y

Check Hook
Fig. 2-2-C

2-3: LOADING MOTOR PCB ASS'Y/ LOADING BELT

(Refer to Fig. 2-3-A)
Tray 1. Remove the Loading Belt. D
Fig. 2-1-B 2. Remove the screw .
3. Remove the Loading Motor PCB Ass'y.
2-2: TRAVERSE ASS'Y (Refer to Fig. 2-2-A) 4. Remove the 2 screws .
5. Remove the Loading Motor.
1. Remove the screw . 6. Remove the Gear Pulley.
2. Unlock the 2 supports .
3. Remove the Insulator (R) from the Loader Sub Ass'y. Loading Belt
4. Remove the Traverse Ass'y. 




Loading Sub Ass'y
 E

Loader Sub Ass'y

Gear Pulley

 
Insulator (R)
Loading Motor PCB Assy

Traverse Ass'y 
Screw Torque: 2.5 0.3kgfcm (Screw )
Screw Torque: 1.0 0.3kgfcm (Screw )
Screw Torque: 2.0 0.3kgfcm Fig. 2-3-A
Fig. 2-2-A

DV-610AV-S 33
5 6 7 8
 1 2 3 4

NOTE 2-4: RACK LOADING/MAIN GEAR/PULLEY GEAR

(Refer to Fig. 2-4-A)
1. In case of the Pulley Motor installation, check if the value
of the Fig. 2-3-B is correct. 1. Unlock the support  and remove the Gear Pulley.
A 2. When installing the wire of the Loading Motor PCB Ass'y, 2. Remove the Gear Main.
install it correctly as Fig. 2-3-C. 3. Press down the catcher  and slide the Rack Loading.
Manual soldering conditions
Soldering temperature: 320 20 C
Soldering time: Within 3 seconds Gear Pulley Rack Loading
Soldering combination: Sn-3.0Ag-0.5Cu
3. When installing the Loading Motor PCB Ass'y, install it Gear Main
correctly as Fig. 2-3-D.
4. In case of the Loading Motor PCB Ass'y installation, hook
the wire on the Loader Sub Ass'y as shown Fig. 2-3-E. Loader Sub Assy



B
Fig. 2-4-A
Pulley Motor 7.0 0.1 mm
NOTE
Loading Motor
1. In case of the Rack Loading installation, hook the Rack
Loading on the Loader Sub Ass'y as shown Fig. 2-4-B.
2. When installing the Gear Main, take care the direction of
Safety surface for pressing
of the insert. up or down as shown Fig. 2-4-C.
Fig. 2-3-B

BROWN (1) Rack Loading

WHITE (2)
C

Loader Sub Ass'y (Bottom Side)

Check Hook
Loading Motor PCB Assy
Fig. 2-3-C Fig. 2-4-B

Rack Loading Up Side

Main Gear

Down Side
Fig. 2-4-C

2-5: CLAMPER ASS'Y (Refer to Fig. 2-5-A)

A B
1. Press the Clamper and rotate the Plate Clamper
The Lever should be position
between A and B. clockwise, then unlock the 3 supports .
Fig. 2-3-D
2. Remove the Plate Clamper, Magnet Clamper and
Clamper.
Check Hook Check Hook

E Plate Clamper

Magnet Clamper

Main Frame

Loading Motor PCB Assy

 
Check Hook Clamper
Fig. 2-3-E  Fig. 2-5-A

34 DV-610AV-S
1 2 3 4
 5 6 7 8

NOTE
1. In case of the Clamper Ass'y installation, install correctly Feed Motor
as Fig. 2-5-B.
Gear Motor A

Plate Clamper
Check Lock

Clamper  
Traverse Ass'y 
Gear Feed
Fig. 2-5-B

2-6: HOLDER TRAVERSE/INSULATOR (F)/INSULATOR
(R) (Refer to Fig. 2-6-A) Rack Feed Ass'y Gear Middle
B
Pickup leneses 
1. Remove the Holder Traverse. GEM1004
2. Remove the 2 Insulator (F). GED-008 Switch PCB Ass'y

3. Remove the Insulator (R).


Insulator (R) Screw Torque: 1.3 0.3 kgfcm (Screw )
Screw Torque: 3.0 0.3 kgfcm (Screw )
Screw Torque: 1.0 0.3 kgfcm (Screw , )
Traverse Ass'y Fig. 2-7-A

Insulator (F) NOTE

1. When installing the Rack Feed Ass'y, push both ends to
Holder Traverse
align the teeth as shown Fig. 2-7-B. Then install it.
2. In case of the Gear Motor installation, check if the value C
of the Fig. 2-7-C is correct.
Insulator (F) 3. When installing the wire of the Switch PCB Ass'y, install
it correctly as Fig. 2-7-D.
Manual soldering conditions
Fig. 2-6-A
Soldering temperature: 320 20 C
NOTE Soldering time: Within 3 seconds
Soldering combination: Sn-3.0Ag-0.5Cu
1. In case of the Insulator (F) installation, install correctly 4. After the assembly of the Traverse Ass'y, hook the wire
as Fig. 2-6-B. on the Traverse Ass'y as shown Fig. 2-7-E.
Insulator (F)
Rack Feed Ass'y
D
Traverse Holder

Push Push

Fig. 2-6-B

[OK] [NG]
2-7: SWITCH PCB ASS'Y/GEAR MIDDLE/GEAR FEED/
RACK FEED ASS'Y/FEED MOTOR
(Refer to Fig. 2-7-A)
Fig. 2-7-B
1. Unlock the support .
2. Remove the Gear Middle.
3. Remove the screw . E
4. Remove the Rack Feed Ass'y.
5. Remove the screw . Gear Motor
8.0 0.2 mm
6. Remove the Switch PCB Ass'y.
7. Remove the screw . Feed Motor
8. Remove the Gear Feed.
9. Remove the 2 screws .
10. Remove the Feed Motor.
Safety surface for pressing
11. Remove the Gear Motor. of the insert.
Fig. 2-7-C

DV-610AV-S 35
5 6 7 8
 1 2 3 4

Switch PCB Ass'y

~ FEED MOTOR ~
WHITE (4)
A BROWN (3)

Install wire from (1) to (4) in order.

~ SPINDLE MOTOR ~
YELLOW (2)

GREEN (1)

Fig. 2-7-D

Traverse Ass'y
Check Hook
B

Check Hook
Check Hook

Check Hook

Loosen the wire in the direction of the arrow.

Fig. 2-7-E

2-8: FFC WIRE HANDLING

C
1. When installing the FFC, fold it correctly and install it as
shown from Fig. 2-8.
NOTE
1. Do not make the folding lines except the specified
positions for the FFC.

[ 24 pin FFC ]

Printing Surface Fold

79 1 mm

Reinforcement Plate
To Pick Up PCB
Fig. 2-8

36 DV-610AV-S
1 2 3 4
 5 6 7 8

8. EACH SETTING AND ADJUSTMENT

8.1 RE-WRITE FOR DVD FIRMWAVE
1. Purpose A
After replacing the DVD MT PCB Assy, be sure to update the firmware to the latest version. The firmware of the Assy for
service may not be the latest.

2. Procedures for creating the disc for updating

Necessary tools:
1 PC with a CD-R/CD-RW drive
2 Blank CD-R or CD-RW
3 Firmware file (.BIN)

How to create:
1 Start up the program for writing to CD. B
2 Load a blank disc in the CD-R/CD-RW drive.
3 Enter "PIONEER" as the volume label.
4 Select the .BIN file.
5 Write the latest version of the firmware in ISO 9660 format.

3. Procedures for updating the firmware

How to update:
1 Turn on the main unit and open the disc tray.
2 Place the disc for updating in the disc tray and close the tray.
3 Press the PLAY button. C

While the screen shown at left is being displayed, updating is in progress.

DO NOT TURN OFF THE POWER DURING UPDATING.

D
4 Updating of the firmware is completed.
When the screen with the Pioneer logo is displayed, updating is completed.
The time required for updating is about 2 minutes.

DV-610AV-S 37
5 6 7 8
 1 2 3 4

4. How to confirm the version of the firmware

Press the ESC then the CHAP key on the remote control unit for servicing. The version of the firmware is labeled ROM
NUMBER. Check if the version is the latest one.
A

AREA:WY REGION:2
ROM NUMBER YJC8223A
REG CHK 20
SUM CHK 02A6
FL VERSION 1.16
CHIP VERSION 1389FE

How to interpret the version code:

YJC 8223A

Number of releases on the same release date

Release date:(Example:2008.2.23)
8: Year
2: Month (1-9 [Jan-Sep], A-C [Oct-Dec])
C 23: Day

Fixed

5. Troubleshooting
 If updating of the firmware failed
If the main unit was turned off during updating, it cannot initialize and start up again properly. In such a case, replace the
flash ROM on the DVD MT PCB Assy.
 If updating of the firmware using the disc for updating failed
D
Was the disc for updating recognized properly?
Check if the volume label of the disc is PIONEER.
Is playback of a disc other than the disc for updating possible?
If playback of a test CD is also impossible, a reading section, such as PU, may be defective. In such a case, repair the
defective part first.
If playback of a test CD is possible, the disc for updating may be defective. Check for any scratches or foreign matter,
such as fingerprints, on the reading surface.
If no problem is found with the disc, create a new disc for updating again.

38 DV-610AV-S
1 2 3 4
5 6 7 8

DV-610AV-S 39
5 6 7 8
 1 2 3 4

9. EXPLODED VIEWS AND PARTS LIST

NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List.
The mark found on some component parts indicates the importance of the safety factor of the part.
A Therefore, when replacing, be sure to use parts of identical designation.
Screws adjacent to mark on product are used for disassembly.
For the applying amount of lubricants or glue, follow the instructions in this manual.
(In the case of no amount instructions, apply as you think it appropriate.)
9.1 PACKING

WVXZT5 Only
B

WSXZT5 Only

Except
WVXZT5

WVXZT5
Only

40 DV-610AV-S
1 2 3 4
 5 6 7 8

(1) PACKING SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

> 1 Power Cable See Contrast table (2) 9 Operating Instructions (S/D) See Contrast table (2)
2 Audio/Video Cable 06CPBA2006 10 Operating Instructions (R) See Contrast table (2) A
3 Remote Control See Contrast table (2)
4 Package Pad 792WHAA237 11 ........
5 ........ 12 ........
13 Package See Contrast table (2)
6 Operating Instructions (E) See Contrast table (2) 14 Gift Box See Contrast table (2)
7 Operating Instructions (E/I) See Contrast table (2)
8 Operating Instructions (G/F) See Contrast table (2)

(2) CONTRAST TABLE

DV-610AV-S/WYXZT5, /WVXZT5, /WSXZT5, DV-610AV-K/WYXZT5 and WSXZT5 types are constructed the same
B
except for the following:
DV-610AV-S/ DV-610AV-S/ DV-610AV-S/ DV-610AV-K/ DV-610AV-K/
Mark No. Symbol and Description
WYXZT5 WVXZT5 WSXZT5 WYXZT5 WSXZT5
> 1 Power Cable 1206158802 1206138802 1206158802 1206158802 1206158802
3 Remote Control 076E0PP121 076E0PP121 076E0PP121 076E0PP131 076E0PP131
6 Operating Instructions (English) Not used J2L50501A Not used Not used Not used
7 Operating Instructions J2L50221A Not used Not used J2L50221A Not used
(English, Italian)
8 Operating Instructions J2L50222A Not used Not used J2L50222A Not used
(German, French)

9 Operating Instructions J2L50223A Not used Not used J2L50223A Not used C
(Spanish, Dutch)
10 Operating Instructions (Russian) Not used Not used J2L50601A Not used J2L50601A
13 Package 792WHAA252 792WHAA253 792WHAA252 792WHAA252 792WHAA252
14 Gift Box 793WCDD677 793WCDD788 793WCDD775 793WCDD714 793WCDD774

DV-610AV-S 41
5 6 7 8
 1 2 3 4

9.2 EXTERIOR SECTION

A
C

D
4
A

D
B

E D
B

42 DV-610AV-S
1 2 3 4
 5 6 7 8

(1) EXTERIOR SECTION PARTS LIST

Mark No. Description Part No. Mark No. Description Part No.

1 DVD MT PCB Assy A2L502A130 17 Screw,Tap Tite(B) (3x6.0) See Contrast table (2)
2 OPERATION PCB Assy See Contrast table (2) 18 Screw,Tap Tite(B)Pan (3x6) 810913060U A
3 ........ 19 Screw,Tap Tite(P) (2.6x8) 811022680U
> 4 POWER PCB Assy A2KL502A240 20 Screw,Tap Tite(P) Bind WH7 8110I2680U
5 DVD MECHA ASSY A2L101A650
21 Screw Pan 810213060U
6 Shield,21Pin 761WSA0237 22 Sheet DVD 723674A001
7 ........ 23 Front Cabi Assy See Contrast table (2)
8 ........ 24 Flap, DVD 712WPAA171
9 Plate,Cover power 755WPAA035 25 Spring, Flap-DVD 743WKA0052
10 Holder,FFC 761WPA0396
26 Cord Connector (CD502) 06E82G3301
27 Cord Jumper (CD601) 122H0B1003 B
11 Cushion,Leg VEB1349
12 Cabinet,Top See Contrast table (2) 28 Cord Jumper (CD7301) 122H0C3002
13 Spring Earth 743WKAA015 29 Cord Jumper (CD605) 06CU241203
14 Cushion 65TS10-7.5 8965TS0610 30 Flat Cable WAL6815038
15 ........
31 Spring Earth 753WUAA013
16 Screw,Tap Tite(B)-R (3x5.5) 815223055U

(2) CONTRAST TABLE

DV-610AV-S/WYXZT5, /WVXZT5, /WSXZT5, DV-610AV-K/WYXZT5 and WSXZT5 types are constructed the same
except for the following: C
DV-610AV-S/ DV-610AV-S/ DV-610AV-S/ DV-610AV-K/ DV-610AV-K/
Mark No. Symbol and Description
WYXZT5 WVXZT5 WSXZT5 WYXZT5 WSXZT5
2 OPERATION PCB Assy A2L502A270 A2L502A270 A2L506A270 A2L502A270 A2L506A270
12 Cabinet, Top 702WSBA075 702WSBA075 702WSBA075 702WSBA076 702WSBA076
17 Screw,Tap Tite(B) (3x6.0) 810923060U 810923060U 810923060U 810923060S 810923060S
23 Front Cabi Assy 7A701B096A 7A701B096A 7A701B096A 7A701B0173A 7A701B173A

DV-610AV-S 43
5 6 7 8
 1 2 3 4

9.3 06 DVD MECHA SECTION

Cannot supply separately.

AB If the repair is needed, replace the
Lubricating Oil LOADER SUB ASS'Y.
GYA1001

Daifree AB
GEM1036
AB
AB
AC
AB
AB

C
AB Lubricating Oil
GYA1001

AC

CD2001 SW1
PCB610
Pickup leneses (LOADING MOTOR PCB ASS'Y)
GEM1004
GED-008
D
CD2302

Do not replace the parts. Because,

minute adjustments are needed if
this condition is disassembled
AA further more.
If the repair is needed, replace the
DVD MECHA ASS'Y.
Grease
GEM1018

PCB640
SW2
Note : (SW PCB ASS'Y)

CD2301

CLASS NOTE: Applying positions AA, AB and AC for the

PART NO. MARK
grease are displayed for this section.
GREASE GEM1018 AA Check if the correct grease is applied for each
GYA1001 AB position.
F GEM1036 AC

44 DV-610AV-S
1 2 3 4
 5 6 7 8

06 DVD MECHA SECTION PARTS LIST

Mark No. Description Part No.
1 ........
2 Gear,Middle 92P100117A A
3 Loading Motor 1515S98004
4 Pulley,Motor 92P100097A
5 FEED Motor 1515S98004

6 Cord Jumper (CD2001) 12C14O2202

7 Cord Jumper (CD2302) 12C1051601
8 Insulator (F) 92P200013A
9 Belt,Loading 92P200015A
10 Insulator (R) 92P200016A

B
11 Frame,main 92P100119A
12 Tray (R) 92P100151A
13 Holder ,Traverse 92P100125A
14 Gear,Pulley 92P100123A
15 Gear,Main 92P100124A

16 Gear,Feed 92P100116A
17 ........
18 Plate, Clamper 92P000023A
19 LOADER SUB ASSY (R) 92AAA0024A
20 Clamper 92P100122A
C

21 Screw,Pan (M1.7x3 P3) 814011730U

22 Screw,Pan (M1.7x2.3 P3) 814011723U
23 Rack,Loading 92P100121A
24 Gear,Motor 92P100088A
25 Feed Rack Assy 92AAA0017A

26 Screw,T-Tite(B) (M1.7x5.0 P3) 813381750U

27 Screw,Gear Feed 92P700007A
28 Cord Jumper (CD2301) 12C1061601
29 Switch (SW1) 0515S32003 D
30 Push Switch (SW2) 0500101036

31 Screw,Tap Tite(P) (2.6x8) 811022680U

32 Sems.Tap Tite(P) (2x8) 816112080U
33 Screw (Bind 2x8) 811022080U

DV-610AV-S 45
5 6 7 8
 1 2 3 4

10. SCHEMATIC DIAGRAM

10.1 DVD MT PCB ASSY(1/7)
A

FROM/TO LOADER/MOTOR DRIVE 1 4

B4016 V+1R8D

ALRCK
33 ASDAT0
33 ASDAT1
33 ASDAT2
ABCK
ACLK

ADAC_GND
W833 V+3

B4014 V+3
V1P4
V+3D
X4001
R4046 10

EBMS160808
A102_RDC45
EBMS160808
A102_RDC45
12P CH
C4048
100GT02720

20P CH
R4047 33

R4022

C4034

C4041
100K
27MHz

0.1 B
R4050 33

11P CH
C4049

4D03WGJ0103T5E
R4025

C4043

1000 YK_P

R4038
C4035

NC
B

0.1 B
100K

R4043
R4040

6.3V 470 YK_P

NR4003
A C4033 C4047

0.1
B 0.001 B

0.1 B
C 0.001 B

W830
PLLVDD3 R4026

W807
NC
D

C4046

C4023
R4024

C4060
6.3V
E W816 RFVDD3 6.8

RFV33
F 750K
MDI1

R4027 100
C4031
0.033 B

0.1 B

C4042
0.047 B

B
C4044
LDO1

10 B
(2125)
C4061
(2125)

4.7 B

3.3 0.0015 B
1.3 C4024
LDO2

C4032

1.0 C4063
0.047
V1P4
C4028
DMSO
FMSO

1.5

1.7
1.5
1.3
1.6
3.3

3.3
1.4
1.5
1.5
1.7
3.2

0.8
0.6
1.0
0.5
1.9

1.9
3.3

3.3
3.3

1.6

1.6

1.7
0.1 B NC NC NC
TRCLOSE

0
0

0
0
0

0
0
0
B TROPEN 256255 254 253 252251 250 249 248 247 246245 244 243242 241240 239 238 237 236 235 234 233 232 231 230 229 228 227 226 225 224 223 222 221 220 219 218 217 216 215 214
TRSO 1.4
OSN

RFRPAC
RFRPDC
RFVDD3
ADCVSS
ADCVDD3
LPFOP
LPFIN
LPFIP
LPFON
PLLVDD3
PLLVSS
JITFN
JITFO
XTALI
XTALO
RFVDD18
RFGND18
SADCVSS18
SADCVDD18
ADACVDD3
ADACVSS3
CH7
CH8
ADACVDD1
ADACVDD2
CENTER
ALS
AL
AVCM
AR
ARS
LFE
ADACVSS1
ADACVSS2
APLLVSS
APLLCAP
APLLVDD
SPDIF/GPIO23
GPIO12
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
FOSO C4027 0.1 B 1.1
RFGC
OPO R4020 15K 0.9
OP+ IREF
C4026 3.3
OP- AVDD3
TROUT 0.1 B 0
AGND
TRIN D C4014 1 B 0 253 HRZFC
DVDA
STBY A C4015 1 B 0
V20 DVDB 254 CRTPLP
B C4016 1 B 0
LIMIT DVDC
C C4017 1 B 0 255 RFGND
IOA DVDD
RF RF C4103 1 B 1.6
DVDRFIP 256 OSP
2.2
D_GND MA
2.2
MB
2.2
MC
2.2
MD
NC SA
NC SB
E 2.0
SC/TNI
FROM/TO MEMORY/USB F 2.0
SD/TPI
MDI1 0.2
MDI1
LDO2 0.2
MDI2
LDO1 2.5
C FP_DO C4013 0.1 B 3.3
LDO2
LDO1
STB C4005 3.3
FP_DI SVDD3
C4019 TP4010 0
FP_SCK 0.1 B CSO/RFOP
V+3D TP4011 0
V20 0.1 B RFLVL/RFON
USB_P_ON-L 0
V1P4 SGND
USB_FLAG 2.7
270P CH
270P CH

V2REF
C4001 0.0022 B

0.015 B

C4105 0.0022 B

C4007

USBP
0.1 B
0.1 B

2.0
V20
680K

USBN
1.4
USB_GND VFEFO
IR TP4012 1.3
C4020

0.1 B

EFO MPEG/MICON IC
MA0
C4003
C4002

C4008
C4009

TP4013 1.3 IC4002

R4005

MA1 TEO
1.3 MT1389EXE/S-L
MA2 TEZISLV
MA3 OPO 1.2
OP_OUT
MA4 OP- 1.7
OP_INN
MA5 OP+ 1.6
MA6 OP_INP
DMSO R4015 13K +-1% 1.9
MA7 DMO
FMSO R4016 8.2K +-1% 1.3
MA8 FMO
MA9 TROPEN 0
TROPENPWM
MA10 TP4036 R4017 22K 1.4
MA11 PWMOUT1/_ADIN0
TRSO R4018 13K +-1% 1.3
SDCKE TRO
FOSO R4019 13K +-1% 1.4
SDCLK FOO
0
C4037

C4038

DBA0
(2125)

AGND18_DMPLL
4.7 B

0.1 B

D DBA1 1.9
AVDD18_DMPLL
DCS# USBP 0
DRAS# USB_DP
DCAS# USBN 0
USB_DM
DWE# V+3D W813 3.3
VDD33_USB
STBY POWER CTL
C4012 C4030

C4036

DQM0 0
10 B

0.1 B
(2125) (2125)

DQM1 R4039 VSS33_USB

Q4004 0.8
DQ0 PAD_VRT
DQ1 V+1R8D W815 KTC3875S_Y_RTK 5.1K +-1% 1.9
VDD18_USB
C4029

R4059 1.47 3.18

10 B

0.1 B

DQ2 C4075 0
VSS18_USB
DQ3 3.3
DQ4 10K USB_XTALO/GPIO15
56P CH 3.7
DQ5 USB_P_ON-L W858 (R4053) 0.6 USB_XTALI/GPIO14
DQ6 0
USB_FLAG FG/GPIO16
DQ7 0
IOA22/GPIO18
DQ8 W857 C4021 1.9
IOA W851 DVDD18
DQ9 0.1 B 2.0 65 DVDD33
DQ10 R4054 10K IOA2
DQ11 TP4001 2.1 66 XIOWR
A2 IOA3
DQ12 TP4002 2.1
A3 IOA4 67 A16
DQ13 TP4003 1.9
DQ14 A4 IOA5 68 HIGHA7
TP4004 2.1
UP1_2/GPIO19

DQ15 A5 IOA6
IOA21/GPIO17

UP1_5/VSDA
UP1_3/VSCK
UP1_4/VSTB

TP4005 2.6
UP3_4/RXD
UP1_7/SDA

UP3_5/TXD
UP1_6/SCL

A0 A6 IOA7
A1 TP4006 2.3
DVDD18

DVDD33
DVSS18

DVSS33

A7 HIGHA0
HIGHA6
HIGHA5
HIGHA4
HIGHA3
HIGHA2
HIGHA1

UP3_0
UP3_1
XUWR
XIOCS

XIOOE

A2 2.3
XURD

TP4007
IOA20

A8 IOA18
IOA1

IOA0
AD0
AD1

AD2
AD3
AD4
AD5
AD6

AD7
ALE

A17

A3
E 0
ICE

A18 TP4008 IOA19

A4
A5 A19 TP4009 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101102103104105106107
A6
0

0
0

0
0

0
3.3
3.3

0.5
1.7
1.9
1.9
2.1
1.1
2.0

1.9

1.8
1.8

1.1
1.1
1.4
1.5
1.3
0.1
1.2
1.2

2.1
1.8
TP4033 UWR# 3.2
3.2
3.3
3.2
33 3.2
3.0
3.1
3.3
3.3

3.2
3.3

33

A7 V+3D NC NC
R4014

R4004

A8
10K

10K

TP4034 URD#

A9
TP4015
TP4016
TP4017
TP4018
TP4019
TP4020
TP4021

TP4022
TP4023

TP4024
TP4025
TP4026
TP4027
TP4028
TP4029
TP4030
TP4031

TP4032

TP4044

SDA TP4108
A10
SCL TP4107
A11
R4035

A12
3.3

3.3

3.3

A13
0

A14 8 7 6 5
EEPROM 4K IC IC4001

A15
S-24CS04AFJ-TB-GE

EBMS160808
VCC

A102_RDC45
WP

SCL

SDA

R400110K
B4018

A16
0.1 B
C4055
B
C4022

C4025

A17
B

C4051

A18
0.1

0.1

0.1

A19
A20
GND
NC

NC

NC

AD0
AD1
100P CH

4D03WGJ
C4131

NR4001

1 2 3 4
0330T5E

AD2
IOCE#
0

IOWR#
PWR#

PRD#

AD3
PCE#

AD0
TP4103 AD1

AD2
AD3
AD4
AD5
AD6

AD7
A16
A15
A14
A13
A12
A11
A10

A20

A17

B4010
A9

A1

A0

AD4
AD5 TP4109 BLM18BD102SN1
TP4014

AD6
AD7
FP_SCK
V+1R8D

FP_DO
FP_DI

PWR#
RXD
SDA

TXD
STB

SCL

F PCE#
PRD#

46 DV-610AV-S
1 2 3 4
 5 6 7 8

MPEG/MICON/DSP SCHEMATIC DIAGRAM DVD MT PCB ASSY (1/7)

(A2L502A130) A

TROUT
ALRCK

V+3A
XMMUTE
XAMUTE
33 ASDAT0
33 ASDAT1
33 ASDAT2
ABCK

V+1R8D
DAC_XCS0
ACLK

STBY

V+1R8
SCK

PWDN#
TRCLOSE
VSEL1

LETTER

V+1R8
ADAC_GND

SQUEEZE
B4014 V+3

B4007 ASPDIF

TRIN
SD

I/XP
TO AUDIO/JACK
EBMS160808
A102_RDC45

BLM18BD
221SN1D
33 W820 TO VIDEO SD

W804
33 SCK
DAC_XCS0

TP4089
TP4049
TP4065

TP4046
VSEL1
C4011 XAMUTE
R4038

100P CH
LETTER
R4043
R4040

XMMUTE
6.3V 470 YK_P

SQUEEZE
C4084 0.1 B

16V47 ALRCK

V+3V
I/XP

C4110
YK_P ABCK

100P CH
C4117
R/CR
ACLK
W807

B/CB
C4023

C4128 ASDAT0
G/Y
ASDAT1
0.01 B CVBS
ASDAT2
S_C
ASPDIF
TP4090

S_Y
10 B
(2125)

3.3 0.0015 B

1.2 C4066
3.3 C4065

0 R400810K

0 R4006 10K

1 B
3.3 0.1 B

3.3 0.1 B
1.3 C4024

3.3 C4067
R4061 51K D_GND
1.0 C4063

R4002 D_GND
1.6

1.7

1.9

3.3

3.3

3.3

2.9

1.1
NC NC NC NC
0
0
0

0
0
0
0

0
5 224 223 222 221 220 219 218 217 216 215 214 213 212 211 210 209 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193
2.2K +-1% FROM/TO POWER PORT B
0 0 R4064 150+-1% TP4060

129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192
AVCM
AR
ARS
LFE
ADACVSS1
ADACVSS2
APLLVSS
APLLCAP
APLLVDD
SPDIF/GPIO23
GPIO12
GPIO11
DVDD18
GPIO10
GPIO9
TS_PWM
TS_ERROR
DVDD33
TS_SYNC
TS_CLK
TS_VALID
TS_DATA7
TS_DATA6
TS_DATA5
TS_DATA4
TS_DATA3
TS_DATA2
TS_DATA1
TS_DATA0
DACVDDC
VREF
FS
0.5 S_Y V+5H
3.3 C4074 R4065 150+-1%TP4066 V+3H
0.7 0.1 B S_C DVDD18
PWDN#
0 R4066 150+-1% TP4061
DADVSSB V+1R8
0.4 CVBS V+3
CVBS
192 DACVSSC 3.3 C4083 R4067 150+-1% TP4067 V+3A
DACVDDA
0.4 0.1 B G/Y ADAC_GND
191 Y G
0 R4068 150+-1% TP4062
190 DACVDDB DACVSSA
0.7 B/CB D_GND
B
189 C 0.7 R/CR
R
0 R4069 150+-1% TP4068
AGND18_TX0
1.0 TX2+
TX2P FROM/TO HDMI
1.0 TX2-
TX2N
1.9 C4071 TX1+
AVDD18_TX0 V+3D
1.1 0.1 B TX1-
TX1P HDMI_SDA
1.0 TX0+ HDMI_SCL
TX1N
0 TX0- HPD
AGND18_TX1
1.1 TXC+ TXC-
TX0P TXC+
1.1 C4080 TXC-
TX0N TX0-
1.8 0.1 B TX0+
AVDD18_TX1
1.0
B4015 DVDD18 TX1-
C
TXCP EBMS160808A102_RDC45
1.0 TX1+
TXCN TX2-
0
AGND18_TX2 TX2+
0
AGND33_TX C4081 SW Q4002 A_GND
0 C4069 2SK3019_TL
EXT_CAP
3.2 0.0056 B 0.1 B 3.10 3.2 V+3H
D

AVDD33_TX S
3.2 R4009
AVDD33_VPLL
G

1.3 2.7K +-1% C4082

EXT_RES 4.88
0 R4034
AGND33_VPLL R4003 33K 0.1 B V+5H
0.1 C4130
GPIO8_HPLG 100
5.0 C4088
GPIO7_DDC_CLK
1.8 0.1 B HDMI_SCL
DVDD18
5.0 0.1 B HDMI_SDA
GPIO6_DDC_DA
0.3 HPD
GPIO5 NC C4068
GPIO4 NC
3.3 0.1 B
DVDD33
1.6 TP4069 MA4
RA4
1.6 TP4070 MA5
RA5
1.6 TP4071 MA6
RA6
1.5 TP4072 MA7
RA7
0.1 TP4073 MA8
RA8
RA9
0.1 TP4074 MA9 D
0 TP4075 MA11
RA11
0
DVSS33
3.3 R4082 33 SDCKE
CKE
1.6 C4072 R4083 47 SDCLK
RCLK V+3D TP4104
3.3
DVDD33
1.5 0.1 B 2 TP4076 MA3
RXD TP4040
RA3
2.1 C4073 TP4077 MA2 TXD TP4042
RA2
1.8 D_GND TP4105
DVDD18
1.8 0.1 B TP4078 MA1
RA1
0.6 TP4079 MA0
RA0
123 RD14 0.1 TP4080 MA10
RA10
124 RD13 0 R4070 33 TP4081 DBA1
BA1
125 RD12 1.4 R4071 33 TP4082 DBA0
BA0
2.7 TP4083 DCS#
126 RD11 XRCS
3.1 TP4084 DRAS#
127 RD10 XRAS
2.9 TP4085 DCAS#
GPIO22/SDD0/INT

XCAS
GPIO21/SD_CLK

128 RD9 3.1 TP4086 DWE#

UP1_2/GPIO19

XRWE
UP1_5/VSDA
UP1_3/VSCK
UP1_4/VSTB

2.0 TP4087 DQM1

UP3_4/RXD
UP1_7/SDA

UP3_5/TXD
UP1_6/SCL

DQM1
3.3 NR4002
DVDD33
XRESET

DVDD33 4D03WGJ0330T5E
UP3_0
UP3_1

DQM0

2.9 R4060 33 LIMIT

RD15

GPIO20/SD_CMD
RD7
RD6
RD5
RD4
RD3

RD2
RD1
RD0

1.1 TP4088 DQ8 E

ICE

RD8
IR

97 98 99 100 101102103104105106107108109110111112113114115116117118119120121122123124125126127128
3.3V
1.8V
0
3.2
33 3.2
3.0
3.1
3.3
3.3

3.2
3.3

3.3
3.2
2.9
2.0
0.2
1.0
0.8
0.7
1.1
1.3
3.3
1.0
1.1
1.3
1.0
1.0
1.3
1.0
1.3
1.1
1.1

NC NC C4104
220P CH
C4054

0.01 B 1.9 0 NC
TP4044

TP4106
TP4063
TP4048
TP4051
TP4052
TP4053
TP4054

TP4055
TP4056
TP4057
TP4058
TP4059

5 4
R3112N291A-TR-FA
RESET IC IC4003
R4035

NC
CT
V_OUT

VDD

VSS
R400110K

B
B

1 2 3
C4064
0.1

3.3 3.3 0
0.1

PCB130
R4084 C4091 DMG100
100P CH

W850
4D03WGJ
C4131

4.7K 1 B
NR4001

0330T5E

W846
DQM0

DQ15
DQ14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ7
DQ6
DQ5
DQ4
DQ3

DQ2
DQ1
DQ0

10
SN1
R4051 220 RESET TP4110
FP_SCK

FP_DO

V+3D
FP_DI

V+3
RXD
SDA

TXD
STB

SCL

F
IR

NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.
DURING PLAYBACK.

DV-610AV-S 47
5 6 7 8
 1 2 3 4

10.2 DVD MT PCB ASSY(2/7)

MEMORY/USB SCHEMATIC DIAG

FROM/TO MPEG/MICON/DSP
64Mbit(4M*16) 166MHz SDRAM
IC4005 M12L64164A-5TG
DQ0
0.0

54
DQ1 16Mbit FLASH IC VSS V
DQ2 IC4004 ES29LV160EB-70TG
DQ3
DQ15 1.5

53
DQ4 A17 1.2 1.7 A16 DQ15

48
A16 A15

1
DQ5
DQ6
0.0

52
DQ7 0 1.0 A15 VSSQ VD

47
BYTE# A14

2
DQ8
DQ9
DQ14 1.5

51
DQ10 0 0.8 A14 DQ14

46
VSS A13

3
B DQ11
DQ12
DQ13 1.5

50
DQ13 A0 0.7 1.5 A13 DQ13

45
D15/A1 A12

4
DQ14
DQ15 C4101
3.3

49
MA0 AD7 1.9 2.5 A12 VDDQ V

44
D7 A11

5
MA1 0.1 B
MA2
DQ12 1.5

48
MA3 1.3 1.3 A11 DQ12

43
D14 A10

6
MA4 NC
MA5
DQ11 1.5

47
MA6 AD6 1.2 1.6 A10 DQ11

42
D6 A9

7
MA7
MA8
0.0

46
MA9 0.6 1.5 A9 VSSQ VD
41
D13 A8

8
MA10 NC
MA11
0 DQ10 1.5

45
DWE# AD5 0.7 A20 DQ10
40

D5 A19

9
SDCKE
DQM1
0 DQ9 1.5

44
DQM0 0.8 R4044 DQ9
39

10
DCAS# NC D12 NC NC
DRAS# 10K C4102
3.3

43
DBA1 AD4 1.6 3.3 PWR# VDDQ V
38

11
DBA0 D4 WE# 0.1 B
C
SDCLK
C4062 0 DQ8 1.5

42
DCS# 3.3 DQ8
37

12
A0 VCC RESET#
0.001 B
A1
0.1 0.0

41
A2 C4040 1.6 VSS V
36

13
A3 NC D11 NC NC
A4 1 B 0.1

40
A5 AD3 1.6 NC NC/RFU LD
35

14

A6 D3 NC (WP#/ACC) NC
A7
0 DQM1 1.9

39
A8 1.3 UDQM W
34

15

A9 NC D10 RY/BY# NC
A10
1.6 SDCLK 1.7

38
A11 AD2 1.2 A19 CLK C
33

16

A12 D2 A18
A13
0.7 SDCKE 1.9

37
A14 1.4 A18 CKE R
32

17

A15 D9 A17
NC
A16
1.4

36
A17 AD1 1.4 A8 NC NC
31

18

A18 D1 A7
A19
1.6 MA11 1.7 A11

35
A20 0.9 A7 BA0/
30

19

AD0 NC D8 A6
D AD1
1.6 MA9 1.7

34
AD2 AD0 1.6 A6 A9 BA1/
29

20

AD3 D0 A5
AD4
1.3 MA8 1.7

33
AD5 PRD# 2.6 A5 A8 A10
28

21

AD6 OE# A4
AD7
1.7 MA7 1.7 32
PRD# 0 A4 A7
27

22

PCE# VSS A3
PWR#
2.5 MA6 1.7
31

USB_P_ON-L PCE# 2.6 A3 A6

26

23

USB_FLAG CE# A2
USBN
1.6 MA5 1.7
30

USBP A1 2.5 A2 A5
25

24

USB_GND A0 A1
IR
MA4 1.7
29

FP_DO A4
STB
FP_DI
0.0
28

FP_SCK VSS V
V+3D

E FROM/TO POWER PORT

6.3V 1000 YK_P

V+3
SH4001
0.1 B
C4050

C4120

FLDC-
YQ-12
-28V
FLDC+
V+3E
D_GND
V+5V_USB

NOTE:THE DC VOLTAGE EACH P

NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE D
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. DURING PLAYBACK.
F

48 DV-610AV-S
1 2 3 4
 5 6 7 8

DVD MT PCB ASSY (2/7)

(A2L502A130) A

ATIC DIAGRAM

64Mbit(4M*16) 166MHz SDRAM IC

IC4005 M12L64164A-5TG
C4052
3.3
54

VSS VDD
1

0.1 B
DQ0 1.5 DQ7
53

DQ15
2

3.3
52

VSSQ VDDQ
3

1.5 DQ6
51

DQ14 DQ1
4

B
DQ2 1.5 DQ5
50

DQ13
5

0.0
49

VDDQ VSSQ
6

1.5 DQ4
48

DQ12 DQ3
7

1.5 DQ3
47

DQ11 DQ4
8

V+3
3.3
46

VSSQ VDDQ
9

V+5V_USB

1.5 DQ2
45

10

DQ10 DQ5 HIGH SIDE SW IC

R4010
R4007

100K
10K
IC4007
1.5 DQ1 R5523N001B-TR-F
44

11

DQ9 DQ6 R4021

USB_FLAG /FLG VIN

4
10K 3.3 5.3
0.0
0.001 B
C4143
43

12

VDDQ VSSQ
GND C

2
0
1.5 DQ0
42

13

DQ8 DQ7 TP4035

EN VOUT

5
3.3 5.3
3.3
41

14

VSS VDD 3.3

0

25V 10 KA_P
USB_P_ON-L
2.0 DQM0

C4076

C4077

C4078
40

15

NC/RFU LDQM 0

0.1 B

0.1 B
USB_P_ON-H
Q4003
3.3 DWE# KRC103SRTK
39

16

UDQM WE#

3.3 DCAS#
38

17

CLK CAS#

3.3 DRAS#
37

18

CKE RAS# FROM/TO DISPLAY

CP4002
3.3 DCS#
36

19

NC CS# 00_6232_011_006_800+
FLDC- FLDC- 11
A11 3.3 DBA0 -28V
35

20

BA0/A13 -28V 10
FLDC+ FLDC+ 9 D
1.0 DBA1 D_GND
34

21

A9 BA1/A12 DGND 8
C4115

C4114
B

DGND 7
1

0.0 MA10 V+3E

1
33

22

A8 A10/AP V+3E 6
IR IR 5
1.7 MA0 FP_DO
32

23

A7 A0 DO (F to M) 4
STB STB 3
1.7 MA1 FP_DI
31

24

A6 A1 DI (M to F) 2
FP_SCK CLK 1
1.7 MA2
W848
30

25

A5 A2 CP4004
A2001WV2-4P
33P CH

100P CH

33P CH

100P CH
C4122

C4132

C4134

C4135
100P CH

C4133

1.7 MA3 USBN 4

29

26

A4 A3
USBP 3
C4123
3.3 USB+5V 2
28

27

VSS VDD
0.1 B GND(USB) 1
D4003
L4001
AVRL161A1R1NT DLP11SN201HL2L
E
W837

USBN 2 3
W805
USBP
0.1 B

W806 1 4
D4002
TP4050 W810
(SCHOTTKY 3.0A) AVRL161A1R1NT
W844 D4005
10V 100 YK_P

USB+5V
EC31QS04
C4142
R4048

22K

PCB130
DMG100

CAUTION: DIGITAL TRANSISTOR

:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK. F

DV-610AV-S 49
5 6 7 8
 1 2 3 4

10.3 DVD MT PCB ASSY(3/7)

A
LOADER/MOTOR DR
C2303 0.1 B

V+5S

IOA
C2304 16V 100 KA_P
PICK-UP(GOLD)
CP2301 V+5S
C2301 0.1 B
LD07T2-24ND-03 R2306
1 GND
JG2304 100K
2 F F
JG2305 0.2 4.9 0.0
3 VS V20
6 5 4

R2308
Q2306 UM6K1N
1D

2G

2S

10K
4 VCC
JG2306 E
5 E
JG2307 R2307
6 D D

VR CTL
JG2308 C 100K
7 C

1G

2D
1S
JG2309 IOA
8 SW1(DVD/CD) 1 2 3
JG2302 RF
9 VRF(RF_OUT) 0.0 0.0 0.0
B JG2310 B
10 B
JG2311 A 5.0
11 A 0.0 R2309
JG2312 VCR_CTL
12 VR650(DVD) Q2301 10K
13 VRCOM MDI1 KTC3875S_Y_RTK 0.0
JG2313
14 VR780(CD)
15 GND
JG2314
16 LD_CD(780)
17 PD/GND
JG2303 JG2315
18 LD_DVD(650)
19 GND C2302
20 NC NC
0.1 B JG2316
21 TRKG DRV T+
JG2317 T-
22 TRKG RTN
JG2318 F+
23 FOCS DRV
JG2319 F-
24 FOCS RTN

LOADING
CP2302
00_6232_005_006_800+

FMSO
TRSO
STBY
JG2320 LOAD-
5 LOAD-
JG2321 LOAD+ C2306
4 LOAD+
JG2322 V+6A
3 OPEN TROUT
10V 100
2 GND YK_P
JG2323 TRIN
1 CLOSE

C2323 R2304
0.1 B OPO 10K
TP2330 R2313 R2312
0.0022 B

R2342
C2322

680K

Track 10K +-1% 8.2K +-1

D SLED/SPINDLE
CP2303 OP-
00_6232_006_006_800+ R2316
OP+
6 SW(GND)
TP2324 LIMIT 3.3K
R2319

R2331

5 LIMIT SW
150K

150K

TP2333 R2325
TP2325 MOT_SLED-
4 SLD-
TP2326 MOT_SLED+ Sled R2310 470 +-1
3 SLD+
TP2327 R2329_1
2 SPD- 10K
TP2328 MOT_SPDL+ 1 1/4W
1 SPD+
(2125)
R2338

10K

MOT_SPDL- C2307
V+3F
0.1 B
W802

C2311
0.1 B

E
MOT_SLED+
MOT_SLED-

T+
T-

F
CAUTION:SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
ARE
ATTENTION :LES PIECES REPAREES PAR UN ETANT
NOTE:THE DC
DANGEREUSES AN POINT DE VUE SECURITE
DESCRIBED IN PARTS LIST ONLY. N'UTILISER QUE CELLS DECRITES MEASU
DANS LA NOMENCLATURE DES PIECES. DURIN

50 DV-610AV-S
1 2 3 4
 5 6 7 8

DVD MT PCB ASSY (3/7)

MOTOR DRIVE SCHEMATIC DIAGRAM
IOA
(A2L502A130) A

FROM/TO MPEG/MICON/DSP

V20
A
B
JG2301 TP2332
NR2301 C
JG2329 TP2341 4D03WGJ04R7T5E D
V+3F E

10V 100 YK_P

F

C2320
MDI1
LDO2
3.3 LD DRIV for CD 3.3
LD DRIV for CD LDO1
3.3 Q2304 3.3 LDO1
Q2302 IOA
KTA1504S_Y_RTK
KTA1504S_Y_RTK V1P4
0 0 LIMIT
B
.0 R2309 TROUT

10V 100 YK_P

TRIN
10K

C2321
STBY
JG2330 TP2342 DMSO
FMSO
TRCLOSE
TROPEN
3.1 LD DRIV for DVD 3.1 TRSO
LD DRIV for DVD 2.5 Q2305 2.5 LDO2 FOSO
Q2303 KTA1504S_Y_RTK
OPO
KTA1504S_Y_RTK 2.0 2.0
OP+
OP-
RF

FROM POWER PORT

V+3F
V+5S C
V+6A
D_GND
M_GND
TRCLOSE
TROPEN
DMSO
FOSO
V1P4

TP2329

MOTOR DRIVER IC
IC2301 AM5766
TP2301
3.24 R2311
1.27
28

MUTE VINFC
1

R2304 18K +-1%

NC

13.2 5.6
27

BIAS TRB_1
2

10K
R2313 R2312
NC

13.2 3.34
26

VINTK REGO 2
3

10K +-1% 8.2K +-1% TP2331 R2318

1.46
R2317 D
25
NC

TRB_2 VINSL+
4

5.56 10K
R2316 8.2K +-1%
NC

3.51 R2327
24
NC

OPOUT REGO 1
5

3.3K 3.5
R2325 13.2 10K
13.13
23

VINLD FWD
6

R2310 470 +-1% 0 C2308

13.13
22

GND REV
7

10K
0.01 B
0 0
PGND PGND
30

29

C2307 C2305 C2325_1

1.38 5.76
21

VCTL Vcc1
8

0.1 B 0.1 B 100P CH

NC

2.03 3.22
20

OPIN VOTR-
9

W802
5.77 3.26
19

10

Vcc2 VOTR+
C2311
0.1 B 2.92 3.25
18

11

VOLD- VOSL+
C2312
2.81 1.69 0.1 B
17

12

VOLD+ VOSL-
E
2.88 2.91
16

13

VOTK- VOFC-

2.82 2.77
15

14

VOTK+ VOFC+
MOT_SPDL+
MOT_SPDL-

LOAD+
LOAD-

PCB130
F+
F-

DMG100

NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. F
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.

DV-610AV-S 51
5 6 7 8
 1 2 3 4

10.4 DVD MT PCB ASSY(4/7)

AUDIO/JACK SCHEMATIC DIAGRAM
A FROM MPEG/MICON/DSP

V+12AT
XAMUTE MUTE CTL
XMMUTE Q8014

R8026
KTA1504S_Y_RTK

5.6K
SD
SCK 1.6 1.5
DAC_XCS0 NC

RN1907(T5L_F_T)
W819
ABCK R8022 0 3.2 1.6
XMMUTE 0.9
1 2 3

MUTE CTL
ALRCK (CU223002) (CP8102)

Q2
2.2K

Q8004
SD
ACLK CP8001A2001WV-2A

R8029
TP8001

Q1
SCK

4.7K
ASPDIF SPDIF 1

C8019
1 B
ASDAT0 TP8002 DAC_XCS0 6 5 4
GND 2 0 0 0
ASDAT1 ACLK1
ASDAT2 R8035
C8035
NC
10K +-1%

1.6
3.2
3.2

3.2
2.4
10V 100 YK_P

C8073
0
0

0
16 15 14 13 12 11 10 9

IC8004 PCM1742KE/2K
FROM POWER PORT

PCMMCK
CS
SCK
SI
ZEROL/MA
ZERORZEROA
VCOM
GND_A
AUDIO DAC (C,Lfe) IC

10V 100 YK_P

V+3A

R8049

C8048
B

C8049

C8043
V+12

B
680K
V+12AT

PCMLRCK

1
PCMDATA
PCMBCK
V+5A

VOUTR
VOUTL
GNDD
VDD
D_GND

VCC
1 2 3 4 5 6 7 8

0
1.5

1.6

3.3
4.8
2.4
2.4
ABCK1 C8033 R8036
ASDAT2
ALRCK 10V 100 YK_P 10K +-1%
V+5A
V+3A3

6.3V 220
C8031

C8037

B
YK_P
C8014
0.1 B

0.1
MUTE CTL
C8026 Q8013
0.0022 KTA1504S_Y_RTK
CH
P.CON+3.3V V+12AT R8024 5.6K
Q8001 XMMUTE R8019 2.2K
1.6 1.5
KTA1505S-Y-RTK/P SD
TP8003 0.9 R8031

RN1907(T5L_F_T)
V+3A 3.3 3.3 SCK 0 3.2 1.6

C8020

MUTE CTL
C R8008 DAC_XCS0 1 2 3 10K +-1%
V+3A3

C8044
Q8003
Q2
ACLK1
R8005

2.7 NC

1
10
10K

Q1
1.6
3.2
3.2

3.2
2.4

R8027
0
0

4.7K
16 15 14 13 12 11 10 9 6 5 4
B
C8002

R8007 0 0 0
IC8005 PCM1742KE/2K

V+3A2
PCMMCK
CS
SCK
SI
ZEROL/MA
ZERORZEROA
VCOM
GND_A
AUDIO DAC (Ls,Rs) IC
1
R8009

10
1K

10V 100 YK_P

R8006
0 V+3A1

C8052
R8054

C8047
1 B
680K
TO VIDEO V+5A 5.0
10
PCMLRCK
PCMDATA
PCMBCK
R8012

22K

VOUTR
VOUTL
GNDD

AUDIO_L 0
VDD

MUTE CTL
VCC

AUDIO_R Q8020
KRC103SRTK 1 2 3 4 5 6 7 8
GND
0

0
1.5

1.6

3.3
4.8
2.4
2.4

C8045
C8032
ABCK1
ASDAT1 10V 100 YK_P C8072 R8033
ALRCK
W878 V+5A 10V 100 YK_P 10K +-1%
ABCK ABCK1
V+3A2
6.3V 220

C8034
C8015

C8028
0.1 B

0.1 B
YK_P

MUTE CTL
D W879 ABCK0 Q8012
C8023 KTA1504S_Y_RTK

V+12AT R8038 6.8K 0.0022 CH 0 0

R8023 6.8K D8006 R8003

RN1907(T5L_F_T)

V+12 0 0 0 0
MUTE CTL

1 2 3 MA111 100
R8020 2.2K
Q8002

XAMUTE
Q2

D8005 R8002
SD TP8004
Q1

C8041 R804
R8028

R8017
25V10 KA_P

TP8011
4.7K

ACLK1 SCK 6 5 4 MA111 100

10 DAC_XCS0 2.6 2.6 0 10V 100 YK_P 10K +
C8016

D8004 R8001
3.3 1.6 R8018
ACLK0
TC7SHU04FU(TE85L_F
INVERTER IC IC8001

5 4 MA111 100
0

10 12.5
1.6
3.1
3.1

2.4

NC REF GEN
C8004

VCC
0

Q8009 6.3
16 15 14 13 12 11 10 9
1

KTC3875S_Y_RTK
IC8003 PCM1742KE/2K

PCMMCK
CS
SCK
SI
ZEROL/MA
ZERORZEROA
VCOM
GND_A

5.8 VREF_C
AUDIO DAC (L,R) IC

GND
12.5
1 2 3 REF GEN
C8054

C8050

6.3
R8065

1 B

Q8008
22K

0 1.5 0
NC
PCMLRCK
PCMDATA

KTC3875S_Y_RTK
PCMBCK

REF GEN 5.8 VREF_S

E
VOUTR
VOUTL

12.5 6.3 Q8010

GNDD
VDD
VCC

KTC3875S_Y_RTK 12.5
R8021

2.2K

6.8 6.3 REF GEN

ACLK B8001 1 2 3 4 5 6 7 8
Q8011
UDZSNP6.8B
0

MMZ1608R102CT
1.5
1.5
1.6

3.3
4.9
2.5
2.4

5.8 KTC3875S_Y_RTK
16V 47 YK_P

D8003
C80301 B

R8025

C8039
680K

B
C8027

VREF_F
1

ABCK0 C8040 R80

ASDAT0
10V 100 YK_P 10K
ALRCK
V+5A
V+3A1
6.3V 1000
C8029
C8017

C8036
B

0.1 B
0.001 B
C8013

YK_P
1

C8025

330P CH
AR
AL

F
NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST A
MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WIT
DURING PLAYBACK.

52 DV-610AV-S
1 2 3 4
 5 6 7 8

DVD MT PCB ASSY (4/7)

(A2L502A130) A

COAXIAL
V+12
R8045 C8061
18K +-1% 16V 47 YK_P

100P CH
C8053
R8046

10K +-1%
R8035

5.7

5.7

5.7
0
560P CH

10K +-1%
C8073

C8063

4 3 2 1

AUDIO LPF&AMP IC
IC8002 RC4580IDR
-VS
0.1

- R8072 9 R8092
TP8012
+
220 +-1% 220 +-1%
10V 100 YK_P

+
560P CH
R8049

C8048

B
C8049

C8043
B

-
680K

+VS
0

CH
C8009
R8068

W870
W868
1

R8074 0.6

22K
5 6 7 8 MUTE SW

330P
5.7

5.7

5.7

12.2
1K Q8015
0 2SD1306NE

R8036 R8053 0 MUTE SW

R8073 0.6 Q8016

330P CH
C8010
R8067
10K +-1%
100PCH

10K +-1% 2SD1306NE

C8059

22K
1K
0
R8050 C8060 R8071 10 R8094
TP8013
18K +-1% 16V 47 YK_P 220 +-1% 220 +-1%

R8048
100PCH

18K +-1%
C8056

R8031 R8052

10K +-1% 10K +-1% 7 C

560P CH

C8065 R8076 R8093

C8044

TP8014
5.7

5.7

5.7

220 +-1% 220 +-1%

C8064

16V 47 YK_P
B

4 3 2 1
0.1

0
AUDIO LPF&AMP IC

330P CH
IC8007 RC4580IDR

C8007
-VS

R8077 0.6
- MUTE SW
R8069

22K

+ 1K Q8017
2SD1306NE
10V 100 YK_P

0
+
C8052
R8054

C8047

-
+VS
1 B
680K

5 6 7 8
5.7

5.7

5.7

12.2

330P CH
R8079 0.6 MUTE SW C8008
R8070

Q8018
22K

2SD1306NE
560P CH

1K
C8045

R8033 R8058 C8066 R8078 8 R8095 TP8015

10K +-1% 10K+-1% 16V 47 YK_P 220 +-1% 220 +-1%

100P CH
C8057

R8055 D
R8082
18K +-1%
220 +-1%

R8059 -0.7
R8085 MUTE SW
0
Q8019
100P CH

18K +-1%
C8062

1K 2SD1306NE
0
C8041 R8043 R8061

10V 100 YK_P 10K +-1% 10K +-1%

5
C8067 560P CH

C8069 R8087 R8096

5.7

5.7

5.7
C8046

TP8017
0

4 3 2 1 16V 47 YK_P 220 +-1% 220 +-1%

AUDIO LPF&AMP IC
16V 47 YK_P

-0.7
IC8008 RC4580IDR
-VS

CH
C8068

C8005
R8075

- R8088 0
0.1 B

22K

+ MUTE SW
330P

1K Q8021
+ 0 2SD1306NE
-
+VS
10V 100
C8054

C8050
R8065

YK_P
1 B
22K

5 6 7 8
MUTE SW
5.7

5.7

5.7

12.2

0
E
CENTER
330P CH

R8090 Q8023
C8006

0
R8066

2SD1306NE
LFE
SR
SL
22K

1K
-0.7
560P CH
C8051

C8058 R8081 R8099 TP8019

TK
16V 47 YK_P 220 +-1% 220 +-1%
6 L R SL SR C LFE
C8040 R8041 R8063 H2 H1 H2 H1 H2 H1
0 3 2 3 2 6 5
10V 100 YK_P 10K +-1% 10K +-1% LS/RS/C/LFE
R8091
100P CH

0 MUTE SW 1 1 4 J8002
C8055

Q8024 E E E RCA-405A(CUSN)-06
1K L/R J8001
2SD1306NE
R8080 -0.7 RCA-207B(CUSN)-02
R8064
220 +-1%
18K +-1%
PCB130
DMG100
AUDIO_R

AUDIO_L
AR
AL

F
DIAGRAM IS THE LATEST AT THE TIME CAUTION: DIGITAL TRANSISTOR
D SUBJECT TO CHANGE WITHOUT NOTICE.

DV-610AV-S 53
5 6 7 8
 1 2 3 4

10.5 DVD MT PCB ASSY(5/7)

A
VIDEO SCHEMATIC DIAGRAM

VIDEO DRIVER 6CH IC

IC7301 LA73054
5 0

36
VCC1 AMP1

1
(9dB=H,6dB=L)
C7305 0
CVBS 2.7

35
CVBS in DRIVE1

2
1 B (1D=H,2D=L)
0 C7302
SQUEEZE 5

34
SQ VCC21

3
0.1 B
LETTER 0 2.9

33
LE CVBS out

4
B
FROM AUDIO/JACK 0 0

32
MUTE1 GND21

5
(ON=H,OFF=L)
AUDIO_L C7304
S_C 2.8 2.5

31
C in C out

6
AUDIO_R
0.1 B
0 0 W877

30
GND11 C-DC out

7
FROM/TO MPEG/MICON/DSP
C7306 0
S_Y 2.7

29
Y1 in GND22

8
SQUEEZE 1 B
VSEL1 2
0

28
YC-MIX Y1 out

9
LETTER
(MIX=H,OFF=L)
CVBS
S_C VSEL1 0 0
10

27
IN SW GND23
S_Y (RGB=H,YUV=L)
G/Y C7307 0
G/Y 2.6
11

26
Y2 in GND24
B/CB
1 B
R/CR
0 2
12

25
I/XP MUTE2 Y2 out
(ON=H,OFF=L)
C 5 5 C7317
13

24
LPF VCC22
(P=H,I=L) 0.1 B
C7308
B/CB 2.8 2.4
14

23
CB in CB out
1 B
0 0
15

AMP2 GND25 22
C7309 (9dB=H,6dB=L)
R/CR
2.8 2.5
1 B
16

21

R7315 CR in CR out

1K 0 0
17

20

GND12 GND26
C7312
P-H/I-L
0 10V100 YK_P
Q7302 DRIVE2 0
18

19

I/XP 3.4 REG

KRC103SRTK (1D=H,2D=L)
1.2
0 C7313

P-H/I-L 0.1 B
TP7302
FROM POWER PORT
W889
10V 100
C7319

YK_P

D V+5 TP7303
D_GND
V+6A

E
VSEL1

F NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC D

MEASURED WITH THE DIGITAL TESTER OF PRINTING AND
DURING PLAYBACK.

54 DV-610AV-S
1 2 3 4
 5 6 7 8

DVD MT PCB ASSY (5/7)

(A2L502A130) A

AUDIO_R

AUDIO_L
SQUEEZE

VSEL1
BLM18BD102SN1

BLM18BD102SN1
B7301

B7302
FROM/TO POWER

VIDEO/AUDIO for 21PIN

CP7301 (CP503)
IMSA-9604S-12C
21PIN-G/D-Y G 1
GND 2
21PIN-B/D-U B 3 B
GND 4
21PIN-R/D-V R 5
P-H/I-L_RGB-H RGB-H 6
ASP/FS FS 7
CVBS 8
GND 9
AUDIO L 10
GND 11
AUDIO R 12

TP7301
C
ASP

S_Y

S_C

CVBS

4CH BUS SW IC D
IC7302
SN74CBT3257PWR
MA111

MA111

MA111

BLM18BD102SN1 6.3V 470 YK_P

BLM18BD102SN1 6.3V 470 YK_P

6.3V 1000 YK_P

6.3V 1000 YK_P

D7307

D7308

D7309

3.3 S 5.0

6.3V 470 YK_P

16

VCC
1

0.001 B

C7314

C7315
C7322

C7316

C7318

C7329
R7301

C7330

0.1 B
10K

1.8 1B1 0
15

/OE
2

2.4 1B2 4B1

14

NC
3

B7305
B7304

2.6 1A 4B2
13

NC
4

75 +-1%
75 +-1%

1.3 2B1 4A
1/10W
12

R7316

NC
1/10W
5

R7317
R7321

1.2K
R7320
MA111

MA111

MA111
D7310

D7311

D7312

R7319

1.2K

2.5 2B2 3B1 1.3

11

1.2K
6

75 +-1%1/10W
75 +-1% 1/10W

2.5 2A 3B2 2.4

10
7

R7303

R7304

R7305
75 +-1%

75 +-1%
R7302

1/10W

1/10W

0 3A 2.4 16 15
GND E
8

14 11 12
13
CVBS

4 3
U
V

H2 H1 H2 H1 2 1
3 2 6 5 S-VIDEO OUT for HE
CVBS/Y/U/V J7304
J7302 DIN-409A 6 5
1 4
RCA-405A(CUSN)-08 E E

PCB130
DMG100
CAUTION: DIGITAL TRANSISTOR
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME F
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.

DV-610AV-S 55
5 6 7 8
 1 2 3 4

10.6 DVD MT PCB ASSY(6/7)

HDMI SCHEMATIC DIAGRAM

FROM/TO MPEG/MICON/DSP

C
V+3D
V+5H
TX2+
TX2-
TX1+
TX1-
TX0+
TX0-
TXC+
TXC-
HPD
HDMI_SCL
HDMI_SDA
D_GND
W855
A_GND
W856

W861

W863
D
W865

A_GND

E
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME N
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.

56 DV-610AV-S
1 2 3 4
 5 6 7 8

DVD MT PCB ASSY (6/7)

(A2L502A130) A

TX2+

4
L5902
TX2- EXC28CG900U

3
W862
HDMI CONNECTOR
TX1+ CP5901
7

2
E110001-11
TX1-
8

1
TX2+
D2+ 1
D2-S 2
TX2- C
TX0+ D2- 3
5

L5901 TX1+
D1+ 4
TX0- EXC28CG900U
6

D1-S 5
TXC+ TX1-
D1- 6
7

TX0+
TXC- D0+ 7
8

D0-S 8
TX0-
D0- 9
V+5H TXC+
CLK+ 10
CLK-S 11
TXC-
R5919

R5920

CLK- 12
1.5K

1.5K

5.06 4.89 4.82 C5907

SW Q5906 UM6K1N

3 2 1 CEC 13
2D

1G

1S

10P CH NC NC 14
HDMI_SCL
SCL 15
HDMI_SDA
SDA 16
C5901 GND 17
2G

1D
2S

4 5 6 POWER 18 D
0.01 B W840
4.82 4.89 5.07 HOTPLUG 19
W853
SW Q5902
2SK3019_TL
HPD 0 0
D
S

B5901 3.4
V+3D
100P CH
C5925

EBMS160808A102_RDC45
0.1 B
C5920

C5921

10 B
(2125)

W864

E
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER PCB130
DURING PLAYBACK. DMG100

DV-610AV-S 57
5 6 7 8
 1 2 3 4

10.7 DVD MT PCB ASSY(7/7)

POWER PORT SCHEMATIC DIAGRAM

REG+1.8V IC IC4006
LD1117AL-ADJ-AA3-A-R

D
VIN VOUT ADJ

C4098
3 2 1

B
C4099
3.3 1.8 0.6
W843

1
6.3V 47 KA_P

R4011 R4012
FROM/TO POWER
C4095
0.1 B
C4094

B
C4096
C4086
C4093

12 68+-1%
B

CP4003_1(CP502)
39 +-1%
R4013

A2001WV2-16P
1
1

1 GND
2 P.CON+12V
3 AT+12V for MUTE
4 GND
0.001 B
C4112

5 P.CON+5V
6 P.CON+6V
E 7 GND(M)
8 AT+3.3V TP4064
9 AT+3.3V
10 P.ON-H
W845
11 GND(D)
12 FL DC-
13 FL DC+
14 -28V
15 GND(UUSB)
16 USB+5V

CAUTION :SINCE THESE PARTS MARKED BY

CRITICAL FOR SAFETY,USE ONES
ARE
ATTENTION :LES PIECES REPAREES PAR UN ETANT NOTE:THE
MEA
DANGEREUSES AN POINT DE VUE SECURITE
DESCRIBED IN PARTS LIST ONLY. N'UTILISER QUE CELLS DECRITES DUR
DANS LA NOMENCLATURE DES PIECES.
F

58 DV-610AV-S
1 2 3 4
 5 6 7 8

DVD MT PCB ASSY (7/7)

(A2L502A130) A

TO AUDIO/JACK
W832 B
V+3A
W826 V+5A (AUDIO DAC) V+5A

V+12AT(AUDIO MUTE) V+12AT

B4002 V+12 (AUDIO AMP) V+12
EBMS160808A102_RDC45
D_GND

TO VIDEO

V+5 (VIDEO/OPT/COAX) V+5

V+6A

TO LOADER/MOTOR DRIVE

V+6A (MOTOR) V+6A

B4001 V+5S (OPU) V+5S
EBMS160808A102_RDC45 V+3F (F/E) C
V+3F
M_GND
HDMI+5V REG(300mA) IC W839
D_GND
IC5902 PQ1K503M2ZPH
5.8 5
VIN VOUT
1

R5921
C5922

0.1 B
C5924
B

22K

0 TO HDMI
1

0
R5901

GND GND
2

5
10K

V+5H
5.4 1.2
ON/OFF NR
3

0.01 B
C5923

FROM/TO MPEG/MICON/DSP
0.01 B
C5906

V+5H
6 W841 V+3H (HDMI) V+3H
3-A-R W842 DVDD18 (HDMI) DVDD18
V+1R8
ADAC_GND
PWDN#
W822 V+3 (MPEG/SDRAM/FLASH/RESET) D
V+3
W821 V+3E (FIP/LED/IR)
DJ
6.3V 470YK_P
C4100
C4098

1
B

0.001 B
C4099

FROM/TO MEMORY/USB
1

V+1R8 (CORE) V+3

C4119
R4058
100PCH
V+3E
B
C4096

100
39 +-1%

FLDC-
1

0.01 B
R4028

FLDC+
C4056
10K

13
-28V
D_GND
V+5USB REG(1.3W/1A) IC
V+5V_USB
IC4009
BA00BC0WFP

V_C V_IN GND V_OUT V_ADJ

1 2 6 4 5
E
4.7 6.0 0 5.3 1.3 TP4038
10V 100 YK_P

R4063
C4141

10K R4072 R4073

W849
15K 220
R4074

+-1%

+-1%
4.7K
C4137

KA_P

C4140
25V 10

0.001

PCB130
B

DMG100

NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.
DURING PLAYBACK.
F

DV-610AV-S 59
5 6 7 8
 1 2 3 4

10.8 OPERATION PCB ASSY

A DISPLAY SCHEMATIC DIAGRAM

V651 HNV-08SS84

IR 1 Vout DVDCD TRACK ALL REPEA

2 GND
R666
V+3E 3 B+

6.3V 47 KA_P
47 1/4W
0.1 B
C651

C674
OS651
KSM-2001TC2P

P16
P15
P14
P13
P12
P11
P10
FL+
FL+

G8
G7
P9
P8
P7
P6
P5
P4
P3
P2
P1
32 31 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11
(OPERATION2 PCB)

-19.7
-19.7

-26.8
-22.7
-22.7
-20.5
-26.8
-26.8
-22.7
-20.5
-20.5
-22.7
-20.5
-20.5
-26.8
-26.8
-26.8
-20.5
-25.1
-25.1
Switch
SW667:POWER
POWER D651 1SS133
SW667
D652 1SS133
EVQ11L05R D654 1SS133
NC

D655 1SS133
HDMI LED(RED)

LTL-1CHEE-002A

D656 1SS133
D657 1SS133
D660

D658 1SS133
POWER

D659 1SS133
SW2
GND

P3 TP662
B2013H02-3P

GR8
GR7
P16
P15
P14
P13
P12
P11
P10
P9
P8
P7
P6
P5
P4

P2
P1
CP603

C PCB271
3
2
1

DEG150 SW2

SW1
1/4W

3
2
1

C658
R664

POWER
330

B2013H02-3P
SW2
GND
V+3E

6.3V 47
GND

LED

DOWN ENTER

C653
P10

P11

P12

P13

P14

P15

P16

KA_P
P8

P9

C676
CP604
IR

SW652 SW653

EVQ11L05R EVQ11L05R
RETURN RIGHT -6.0 -13.0 -12.6 -9.5 -13.0 -9.5 -19.0 -19.0 -15.6 3.3 0
SW655 SW654 22 21 20 19 18 17 16 15 14 13 12

P8

P9

P10

P11

P12

P13

P14

P15

P16

VDD
EVQ11L05R EVQ11L05R P7 -12.0
23

11
K2
MENU UP
SW656 SW657 P6 -6.0 23 P7
24

10
P6 12 GND K1
-18.0
EVQ11L05R EVQ11L05R P5
25

P5 STB

9
TOPMENU LEFT -18.0
D SW658 SW659 P4
26

P4 CLK

8
FIP DRIVER IC
-18.0 IC651
EVQ11L05R EVQ11L05R P3
27

P3 DI

7
PT6315
HOMEMENU -18.0
SW661 P2
28

DO

6
P2
-18.0
EVQ11L05R P1
29

P1 OSC

5
-18.0
30

-28V

4
LED4
EJECT -18.0
31

NC GR12 LED3

3
STOP SW666
SW660 -18.0
32

NC GR10 34 GR9 44 GND LED2

2
EVQ11L05R
EVQ11L05R -18.0 VDD
GR8

GR7

GR6

GR5

GR4

GR3

GR2

GR1
33

NC GR11 LED1

1
+SKIP PLAY
SW662 SW663 34 35 36 37 38 39 40 41 42 43 44
NC

-18.0 -18.0 -18.0 -16.0 -16.0 -16.0 -16.0 -16.0 -16.0 3.3 0
EVQ11L05R EVQ11L05R
GR8

GR7

GR6

GR5

GR4

GR3

GR2

GR1

-SKIP PAUSE
E SW664 SW665
LED
V+3E

EVQ11L05R
IR

EVQ11L05R
GND

SW1

SW2
B
C675

F
NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIA
MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SU
DURING PLAYBACK.

60 DV-610AV-S
1 2 3 4
 5 6 7 8

OPERATION PCB ASSY

(WYXZT5, WVXZT5 : A2L502A270) A

(WSXZT5 : A2L506A270)

LL REPEAT A B Switches
SW652 : DOWN
SW653 : ENTER
SW654 : RIGHT
SW655 : RETURN
B
SW656 : MENU
FL-
FL-
G8
G7
G6
G5
G4
G3
G2
G1
P7
P6
P5
P4
P3
P2
P1

19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 2 1 SW657 : UP
SW658 : TOP MENU
-22.7
-20.5
-20.5
-26.8
-26.8
-26.8
-20.5
-25.1
-25.1
-25.1
-25.1
-25.1
-25.1
-25.1
-25.1

-22.3
-22.3

FLDC- SW659 : LEFT

0.01 B
SW660 : STOP
C654

W804 FLDC+ SW661 : HOME MENU

SW662 : + SKIP
SW663 : PLAY
SW664 : SKIP

1SS133
D665
SW665 : PAUSE
1SS133
MS1_2
D669

SW666 : EJECT

EVQ11L05R
P3 TP662

SW668
(W802) USB
W806
GR8
GR7
GR6
GR5
GR4
GR3
GR2
GR1
P7
P6
P5
P4

P2
P1

C612 C
SW2
-28V 0.1 B
SW1 (60 OHM 2.5A)
B601 C608
USB+5V
0.1 B
C658

R655

R657

R656

R658

USB CONNECTOR
10K

HCB2012K-600T25 0.01 B
10K
1K

1K

CP602
USB-A1D102F-4B4N
+5V 1
6.3V 47
C653

0.1 B
P14

P15

P16

KA_P
C676

USBN USB_DN 2
USBP USB_DP 3
GND 4
47P CH

47P CH

.0 -19.0 -15.6 3.3 0

C611

C610

16 15 14 13 12
0
P14

P15

P16

VDD

11

K2
HCB2012K-600T25
(60 OHM 2.5A)

0
10

12 GND K1
B602

3.2 STB
STB
9

3.4 FP_SCK
CLK D
8

IC
W803

0.7 FP_DI
DI
7

FROM/TO MPEG/MICON/DSP
3.2 R654
DO FP_DO CP605
USB+5V
6

2.2 A2001WR2-4P
2.9 R662
GND(USB) 1
OSC
5

100K USB+5V 2
SHIELD CABLE
NC 0 USBP
1 USBP 3
4

LED4
USBN USBN 4 CD605
0
LED3
3

CU241203
NC
CP601
44 GND LED2 NC 0 00_6232_011_102_800+
2

FP_SCK CLK 1
0 FP_DI
VDD
GR3

GR2

GR1

LED1 DI (M to F) 2
1

NC STB STB 3
40 41 42 43 44 FP_DO DO (F to M) 4
.0 -16.0 -16.0 3.3 0 IR IR 5
FFC(1.0mm pitch)
V+3E
GR3

GR2

GR1

V+3E 6
C604
LED

C605
DGND 7 CD601 E
33P CH 2H0B1003
DGND 8
FLDC+ 1 B
FLDC+ 9
-28V -28V 10
FLDC- FLDC- 11

V+3E
B
B
C675

C601

PCB270
1

DEG149
1

GND

F
OTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE.

DV-610AV-S 61
5 6 7 8
 1 2 3 4

10.9 POWER PCB ASSY(1/2)

A
POWER SCHEMATIC DIAGRAM

SH501
YQ-12

D512

1H3-E
CHASSIS GND

C523
250V 0.0033 KX
C516
D505

1N4005-EIC
B
D502

1N4005-EIC

100K 1/2W

400V 0.01 PP
1.5M 1/2W

R512
R503

C515
275V 0.22 ECQUL

NHG
C511_2
T501
C502

81291354

400V 47

2KV 47P SL
D503
0

RL106F-E
D509
3 4 16

C513
50T016H 1N4005-EIC
F501
T1.6A_L_250V 1 2 130 0
2 15 D510
D506
130 0 SF26-F
COIL,LINE FILTER 1N4005-EIC 3 14

16V 1000 ZL P
AC220V-240V_50Hz L501
/60Hz(EU) FH501 FH502
SS11V-03550NT-CH

C521
EYF-52BCY EYF-52BCY 130 0
CD501_2 06158802 4 13
N NC
1

0
12

W4BRH3.5X6X1.0X2
1.6A 250V
2

C L
0 0
AC INLET 6 11 D527
J501 B501
D511

YKE31-0148N
1F5-E

0 -22.5 SR240-F
7 10

C522
0 -22.5
8 9
NC

D519 R511

1F5-E 68 1/4

C520
130 130 0 NC 130
8 7 6 5
IC502 STR-A6159M

NC

FB/OLPSTARTUP
POWER CTL IC

GND
OCP

VCC

C514
D515 R510_1
D 1 2 3 4 500V 470P B
0.1 17.5 0 3.9 D513 R505 1S40-E 2.7 1W

1H3-E 22 1/4W
2KV 100P R
C505

R507

10 1/4W
MTZJ5.6B
D508
R502_1

1W
1.5

50V 2.2 KA_P

PHOTO COUPLER IC
50V 10 YK_P

IC504
680P CH
680K

C506
R504

PS2561AL1-1-V(W)
C508

C509

3.9 10.9 R514

4

1K 1/4W
0 9.9 R515
3

1K
C540
E
R513 0.0068 B C503

6.8K 0.1 B
R516

10

VOLTAGE CTL IC
IC501 KIA431A-AT
1%
R517

1 2K

* The parts except mark cannot be changed. OUT GND IN

R518

3 3K

3 2 1
1.6A 250V
On that occasion, replace whole Assy. 4.69 0 2.39

CAUTION :FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

REPLACE ONLY WITH THE SAME TYPE FUSE
1.6A 250V{F501}

F
ATTENTION :POUR UNE PROTECTION CONTINUE LES RISQUES D'INCEIE
N'UTILISER QUE DES FUSIBLE DE MEME TYPE
NOTE:THIS SCHEMATIC DIAGRAM IS THE
1.6A 250V{F501}
OF PRINTING AND SUBJECT TO CHA
CAUTION :SINCE THESE PARTS MARKED BY ARE
ATTENTION:LES PIECES REPAREES PAR UN ETANT
DANGEREUSES AN POINT DE VUE SECURITE NOTE:THE DC VOLTAGE EACH PART WAS
CRITICAL FOR SAFETY,USE ONES N'UTILISER QUE CELLS DECRITES MEASURED WITH THE DIGITAL TES
DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES. DURING PLAYBACK.

62 DV-610AV-S
1 2 3 4
 5 6 7 8

POWER PCB ASSY (1/2)

(A2L502A240) A

P.CON+12V SW
Q510 KTA1281-Y(GP)
W817
12.9 12.6

R541

5.6K
+-1%
12.3
REG+12V CTL
Q509

R542
D512 KTC3875S_Y_RTK 12.3

+-1%
470
5.0 12.9
1H3-E 5.1
25V 470 YK_P

4.5 REG+12V CTL

4.7K +-1%
Q511 4.5
C523

R509

1K

R543
KTC3875S_Y_RTK

R540

680
+6V REG (DVD MOTOR) IC
B
IC503 R546 R545

W819
PQ070XF01SZH

1K 1/4W
3.3K +-1% 22K+-1%

R524
IN OUT GND ADJ FROM/TO POWER PORT
D534

R519

3.3K
1 2 3 4 CP502 (CP4003_1)
1SS133 P.CON SW
7.0 5.9 0 1.2 A2001WV2-16P
16V100YK_P

Q505

MTZJ2.2B
0

0.01 B
GND

C501
KRC102SRTK GND 1
+-1%
16V 330

R526

D517
6.8K
YK_P
C531

C535

CORD CONNECTOR
2.8 P.CON+12V 2
0
AT+12V for MUTE 3 CD502
P.CON+5V REG (W023) GND 4 E82G3301
D510 Q515 2SD1835S/T-AA L503 B502
P.CON+5V 5
SF26-F 7.0 5.1 22uH HCB2012K-600T25
P.CON+6V 6
6.3V 220 YK_P

R525 R547 TSL0808

16V 1000 ZL_P

W825
6.3V 220 YK_P
5.8 GND(M) 7
C521

10V100 YK_P

C538

100 22
AT+3.3V 8
C536

C541
C527

AT+3.3V 9
0.01 B
P.ON-H(STBY L) 10
GND(D) 11 C
D527 L505 FL DC- 12
FL DC+ 13
6.3V 1000 ZL_P

6.3V 470 YK_P

SR240-F 22uH
MTZJ5.1B

-28V 14
C522

D528

C526

GND(USB) 15
USB+5V 16

-28V P.CON SW
Q502 KTC3209-Y(GP) TO 21PIN/D-TERMINAL/DIGITAL
D519 R511 R529_1
28.4
-28V CTL 28.4
1F5-E 68 1/4W 220 1W
Q503 P.CON+D5V
50V 100 YK_P

27.8
KTA1504S_Y_RTK 100P CH
C524

AT+3.3V
MTZJ27B

R528
C520

0.6 6.8
50V 2.2 KA_P

P.CON+12V
D531

22K AMP_A_OUT_R
C528

0 1/4W AMP_A_OUT_L
R531

10K

G/Y_VIDEO
B/U_VIDEO
R/V_VIDEO
R548
CVBS/C_VIDEO
D515 R510_1 1K P-H/I-L_RGB-H
D
ASP/FS
25V 220 YK_P

1S40-E 2.7 1W 19.0 19.0 FL+ P.CON SW

MTZJ5.1B
MTZJ3.0B

19.7 Q504 A_GND

D535
C517

D536

KTA1281-Y(GP)
1/4W
560
R530

FROM/TO VIDEO

FL+ CTL Q512 A/V for 21PIN

KTC3875S_Y_RTK CP503(CP7301)
FL+ CTL
IMSA-9604S-12C
Q513 G/Y_VIDEO
21.6 21.5
KTA1504S_Y_RTK G 12
R534 R537 D533
20.8 20.7
GND 11 FFC(1.25mm pitch)
100 1/4W 0.6 1K B/U_VIDEO
MTZJ2.2B B 10
0 CD7301
GND 9
R536
R544

2H0C3002
10K
10K

R/V_VIDEO
R 8
P-H/I-L_RGB-H
RGB-H 7
R514 ASP/FS FS 6
1K 1/4W CVBS/C_VIDEO
R515 CVBS 5
GND 4
1K AMP_A_OUT_L
C540 AUDIO L 3
E
13 0.0068 B C503 GND 2
AMP_A_OUT_R
AUDIO R 1
1SS133

1SS133

1SS133
D520

D521

D522

K 0.1 B
R516

R539

4.7K
10

VOLTAGE CTL IC
IC501 KIA431A-AT ACCESSORY
1.2K +-1%
R517

R506

100

UM-4
PROTECT TM601
076E0PP121 BT601
OUT GND IN Q506
R518

R538

R6P(AR)XICI
+-1%

22K
3.3K

3 2 1 KTA1504S_Y_RTK
9.9 3.2
69 0 2.39 R527
0 0 CD6003
35V 22 YK_P

100 3.2 NC TD-OR0201R

MTZJ3.6B

PROTECT 0
C519
R523

D523
22K

Q501
KTC3875S_Y_RTK
PCB240
DPG017
CAUTION: DIGITAL TRANSISTOR F
EMATIC DIAGRAM IS THE LATEST AT THE TIME
ING AND SUBJECT TO CHANGE WITHOUT NOTICE.
OLTAGE EACH PART WAS
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR.
ED WITH THE DIGITAL TESTER THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP
PLAYBACK. IS NON POLAR ONE.

DV-610AV-S 63
5 6 7 8
 1 2 3 4

10.10 POWER PCB ASSY(2/2)

A
21PIN/D-TERMINAL/DIGITAL SCHEMATIC DIAGRAM

CP8102(CP8001)
E8223401
1 SPDIF
2 GND
B

FROM POWER

B8101
P.CON+D5V
MMZ1608R102CT

AT+3.3V
P.CON+12V
P-H/I-L_RGB-H
ASP/FS
AMP_A_OUT_R
AMP_A_OUT_L

G/Y_VIDEO
B/U_VIDEO
R/V_VIDEO 6.3
C8113
CVBS/C_VIDEO
MTZJ6.8B

MTZJ6.8B

MTZJ6.8B

A_GND 6.3V 470 YK_P

1 1/4W
D8103

D8104

D8105
R8120

0.1 B
C8105

6
470 1/4W
R8103
R8104

6.8K

E 3.3 D
Q8
21PIN CTL IN 12.1 21PIN CTL DRV K
R8105 Q8102 0
Q8101 11.4 DVD_RGB_H_OUT
KTA1504S_Y_RTK Q8104 3.2
KTC3875S_Y_RTK 390 1/4W
12.1 KRC104SRTK
11.4 0
D8101

R8101
1SS133

0 3.2
4.7K
R8108

0 0
8.2K
C8101

C8106
0.001 B

0.001 B
R8102

56K

NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE. MEASURED WITH THE DIGITAL TESTER
F DURING PLAYBACK.

64 DV-610AV-S
1 2 3 4
 5 6 7 8

POWER PCB ASSY (2/2)

(A2L502A240) A

C8118

R8107
10V 100 YK_P

1.8K
4.9 C8119
R8106
ASPDIF 2.7 COAXIAL DRV
Q8103 1 B
2.4K
2.1 KTC3875S_Y_RTK
R8123 C8104 7
CP8102(CP8001)

R8121
E8223401 TP8101

3.9K
68 50V 1 KA_P
1 SPDIF +-1%

R8122

150P CH

R8124
C8103
2 GND

100K
220
TP8102 B

COAXIAL
COAXIALJ8102
RCA-117-01

E
2

1
OPTICAL OS8101
RFT5CB1
8
1 INPUT
2 VCC
C8120

0.1 B

3 GND
D_GND

B
C8121

100P
C

21PIN CONNECTOR
J8101
MRC-021V-07_A
R8114 5 21PIN_R

1
220 +-1% 1/10W 6 NC

2
R8115
21PIN_L

3
220 +-1% 1/10W
0.001 B

0.001 B
C8111

4
C8107

5
NC

6
D
7
21PIN_CTL L8101

8
10uH 0405 9

C8112 R8110
1 NC 10
G/Y_VIDEO_OUT
11

6.3V 1000 YK_P 68 +-1% 1/10W 2

12

C8113 NC
R8111 B/U_VIDEO_OUT
13

6.3V 470 YK_P 68 +-1% 1/10W 3

14

C8114 R8112 R/V_VIDEO_OUT

15

6.3V 470 YK_P 68 +-1% 1/10W BLANKING_OUT

16
17

4
18

C8115 R8113 CVBS_VIDEO_OUT

19
33P CH
C8116

6.3V 1000 YK_P 75 +-1% 1/10W

20

NC
21

3.3 DVD_RGB_H_OUT E
Q8105
0 KRA102SRTK
B_H_OUT
104 3.2
04SRTK
0
3.2 R8109

68 +-1% 1/10W
0

* The parts except mark cannot be changed.

On that occasion, replace whole Assy.
CH PART WAS
HE DIGITAL TESTER CAUTION: DIGITAL TRANSISTOR CAUTION: DIGITAL TRANSISTOR PCB240 F
DPG017

DV-610AV-S 65
5 6 7 8
 1 2 3 4

10.11 WAVEFORMS
Note : The encircled numbers denote measuring point in the schematic diagram.

A DVD MT PCB ASSY

MPEG/MICON/DSP
J8001-pin2 (R_Out) J7302-pin6 (CVBS_Out)
IC4002-pin238 (XTALO)
V:200 mV/div. H:500 s/div.
V:1.0 V/div. H:500 sec/div. VIDEO V:200 mV/div. H:10 sec/div.

1 6 11

B
J8002-pin3 (SL_Out) J7302-pin5 (Y_Out)
IC4002-pin146 (SDCLK) V:1.0 V/div. H:500 sec/div. V:500 mV/div. H:10 sec/div.
V:0.5 V/div. H:2 ns/div.

2 7
12

C
J8002-pin2 (SR_Out) J7302-pin3 (U_Out)
IC4002-pin215 (ASPDIF) V:1.0 V/div. H:500 sec/div. V:500 mV/div. H:20 sec/div.
V:1.0 V/div. H:200 ns/div.

3 8 13

D
IC4002-pin231 (ACLK) J8002-pin6 (CENTER_Out) J7302-pin2 (V_Out)
V:1.0 V/div. H:20 nsec/div. V:1.0 V/div. H:500 sec/div. V:500 mV/div. H:20 sec/div.

4 9 14

E J8002-pin5 (LFE_Out) J7304-pin3 (S_Y_Out)

AUDIO/JACK J8001-pin3 (L_Out)
V:1.0 V/div. H:500 sec/div.
V:1.0 V/div. H:500 sec/div. V:500 mV/div. H:20 sec/div.

10
5 15

66 DV-610AV-S
1 2 3 4
 5 6 7 8

DVD MT PCB ASSY POWER PCB ASSY

J7304-pin4 (S_C_Out) J8101-pin1 (21PIN_R) A
V:500 mV/div. H:10 sec/div. V:1.0 V/div. H:200 sec/div.

16 5

B
J8101-pin3 (21PIN_L)
V:1.0 V/div. H:200 sec/div.
21PIN/D-TERMINAL/DIGITAL
J8101-pin11 (G/Y_Video_Out)
V:500 mV/div. H:20 sec/div.

C
J8102-pin2 (COAXIAL_Out)
V:500 mV/div. H:200 nsec/div.
J8101-pin7 (B/U_Video_Out)
V:500 mV/div. H:20 sec/div.

OS8101-pin1 (OPTICAL_Out)
V:1.0 V/div. H:200 nsec/div.

J8101-pin15 (R/V_Video Out)

V:500 mV/div. H:20 sec/div.

8
3

OPERATION PCB ASSY

IC651-pin5 (OSC)
J8101-pin19 (CVBS_Video_Out)
V:500 mV/div. H:20 sec/div.
DISPLAY V:500 mV/div. H:1 sec/div.

1
4

DV-610AV-S 67
5 6 7 8
 1 2 3 4

11. PCB CONNECTION DIAGRAM

NOTE FOR PCB DIAGRAMS :
A 1. Part numbers in PCB diagrams match those in the schematic 3. The parts mounted on this PCB include all necessary parts for
diagrams. several destinations.
2. A comparison between the main parts of PCB and schematic For further information for respective destinations, be sure to
diagrams is shown below. check with the schematic diagram.
Symbol In PCB Symbol In Schematic Part Name
4. View point of PCB diagrams.
Diagrams Diagrams
B C E B C E
Connector Capacitor
Transistor
B C E

B C E B C E SIDE A
Transistor
B C E with resistor

D G S D G S
B
Field effect
D G S transistor P.C.Board Chip Part SIDE B

Resistor array

3-terminal
regulator

11.1 LOADING MOTOR and SW

C
SIDE A SIDE A

LOADING MOTOR
(INSERTED PARTS) SW CD2301
SW2

D
SW1
DED020A
WH

DED021A
BR

GR
YE

M2602 M2601

SIDE B SIDE B
LOADING MOTOR
E
(CHIP MOUNTED PARTS)

A120DED
BR
WH
M2603
CD2302
1
5

68 DV-610AV-S
1 2 3 4
 5 6 7 8

11.2 DVD MT PCB ASSY

SIDE A SIDE A
A

DVD MT PCB ASSY

B

DMG100A

01
C5925 C4123

40
SH
C4050

C4062
R4035
B4010

IC4004
IC4001
IC4005
L5902 L5901
CP5901

R5919 NR4001

C4091 R4084
W846
R5920
B5901
C4102

IC4003
R7320 W855

C4132 C4104
65
R4070
R4071

NR4002 129 C4115

Q5902
R7303

C4114

C4122

2
00
C4143
R7302
R7319

R4059

CP4
R4083

C4133
B7305

C4135

C4134
R4082 W815

W837
C7314
IC4002 C4038 C
C7315

C4007 C4003 R4019

R4018
C4002

D4002
C4069

D4003
R4017
L4001
W861

CP4004
C4077
J7302

C4001

R4016
R4015
C7308C7309

C7318 C4117 C4078 C4141

C4103
IC7302 IC4007
C4142

C4140 C4076
193 1

R4010
R4007
C7307 R2327 Q4003
C4032
IC7301

C4031

W849 R4072
R4063 R4074
R4073
C7316 C7306
B4007 C4024

C7322

IC4009
C2308
R2318
C4044
R4024
C4047

C7304 R2311 R2304

B7302

R4027
R4046

C4042
W830
R4043
R4047

R4025 R2317
CP7301 R2312 R2313
C4063

C4060
C8023

C4137
R8007
J7304

C7319 X4001 R2325

C7312

R2310 W802
IC2301
C2306
R7301

W833

C7329 W877 C8034 C8015 C2325_1

C2305

C2311
C2307
R2316
R8070
R8033

302
C8045 C8028
R8078 IC8005 CP8001 C4023
C8064 C8072

CP2
C8008

Q8018
R8095

W839

D
R8079

C8066
C8032 W842
IC8007
Q8013

C8020 C4011 C2312 C2323

R8008

C8065 C8047 C8026 R2338

C8043 R8024

C2322
Q8003

R8019

C8037 C8014 C4100 R2342

R8027 C8031 C5923 C4119 R2331
C8060 R4038
IC5902

R4028 C2320 R2319

B4001 C4056

IC8004
R4013
C4096

R8049 C8048 C8033

J8002

R8094 C8007

Q8001 C8002

IC8002
R8005 R8009

C5924 R5901 R2329_1

W826

C8061 R5921 C5922

R8022

C8035 Q8004 C8019 C2321

W889
C4094
R8071

C4095 Q2303
R2306 R2309
R8073

C8029 IC4006
D8004

C8073
R2308 Q2301
R8035

R8026
R8029

C8068 Q8014
W841
Q8016 R8001 Q2305
C8027 Q8011
R2307

C8036 C8017
R8085 Q8023

C8067 R8041 R4012

R8081 C8040 C4099
R4011 CP2303
R8018 W879

R8090 C4098 W843

R8088 Q2302 Q2304 Q2306
R8091 IC8001
C8041
B4002

C8058 IC8008 IC8003

R8080

C4093 C4112
Q8024

C8004

C2301
C8016 C2304
J8001

C8038 R8043
C8050 CP2301
R8028

C8069 CP4003_1
Q8012 Q8002
R8023 R8038 E

DV-610AV-S 69
5 6 7 8
 F
E
B
A

D
C

70
SIDE B

1
1

R4048

D4005
W848

W844

R4051
C2303 W821
C2302 R4021
W858
W850
W832 W851

R4044
W820

NR2301
C4008

W822
C4009

2
2

R4005
C4030
C4105
C4029
C4036 W813
C4026
W845 W804 C4027 C4040
R4022 C4028

Q4004
C4086 C4034 R4020 C4017 C4037 C4012

DMG100A
W816
C4035

W807
B4014 C4033 C4016 C4013 C4020 R4039

R4058
C4041
R4004

R4054
C4015 C4019 C4005 C4075
C4048 C4043 C4014

R4026
C4021 R4014
C4022
C4061 B4016
C4049 C4025
C4046
R4060 B4018 C4131
C4051 C4055

NR4003

DV-610AV-S
R8012 R4050 C4130
R8006 R4034
C4128 B4015
C4084

W878
R4006

Q4002

Q8020

R8017

B8001
R4040 R4008 C4065 C4074 R4001

R4065
R4064
C4071 C4082 C4054
C8013 C4066 R4066 C4064 C4120
C4080 C4088 C4073
C4083

R8020
C4110 R4061 C4081 C4068

3
3

R4067
C4067 R4002 C5901
D8005 R8003 R4068 C4072 C4052

W864
C8025 R4069 R4009 W856
D8003 D8006 R7315

R8002
C8054
R8021 C7305 C4101
DVD MT PCB ASSY

R8031 R4003
C8044 C7313

R8065
R8036

Q8008
R8054

Q7302
C8046

R8025
C8052 W819
R8061 C8039 C7302 C7317
B7301

Q8010

Q8009
R8059 C8057
C8062
R8064 R8063
R8075 C8030 C8063 D7307
R8055
R8082 C8055 R8052 R8058
R8046 D7308
R8087 R8048

R8053
D7311

R8066
Q5906

C8051 R8045 C8059 C8049

D7310

B7304
R8074 C8056 R8077

Q8019
R8067

Q8017
C8053 R7305

Q8015
R8050
R8092 R8068 R8076 C7330 D7309
R7316 R7321 D7312
R8093

4
4

Q8021
C8009 R8072

R8069
W840
R7317

C8010 C5920
R7304

R8096 R8099 C5921

C8005 C8006
W862

W868
SIDE B
 SIDE A

OPERATION PCB ASSY

5

5
SW668
SW655

SW662 CP601
SW660 SW665 SW663
SW664

CP602
SW661
SW652

W018

R666
R664 A30C5

CP604
W022 W021
W023

W014
W005
W004

W012

W013

W020
CP605 C653 SW659 SW653 SW654

W006
G DEG149A W804

C674

W019
W016
W007
SW657 W001
D660
DEG150A A30C5

D665
W002

D667

W017
G D651
W003

D657
SW666

D652

D656
D658

D654

D655
OS651 CP
60
3
W011 SW658 SW656
D659

V651
SW667
11.3 OPERATION PCB ASSY
6

6
DV-610AV-S
7

7
C658

23

C676
34

12
IC651

C651
C611
R655
R657
R658

DEG150A
1
C675

R662
W806

C610 R656
C605
C601

DEG149A B602
C654

W803

C604
B601

R654
C608
8

8
OPERATION PCB ASSY

71
SIDE B

F
E
B
A

D
C
 1 2 3 4

11.4 POWER PCB ASSY

SIDE A SIDE A
A

POWER PCB ASSY

B

SH
501

C5
L

1
6
J501

D506
L501

C511_2
FH501 F501 FH502 R503
N R512
D503

C51
D502 B501 5
C502
C
- REPLACE AS MARKED. D509
C8104
RISK OF FIRE IC502
D505 D511 C505
C8118
J8102

C513 C509
W006

W003

W002
W001
3
50 R502_1

D508
IC C531 Q510 R505

D513
C514

R507
CP8102
OS8101

W817
R524

W021
W022 T501
DPG017A C506

IC504
W013
D534
W012 C523
D517
C527 W007
C535 W825

D Q515 D512
W018
W017

W016 D510
C538 C521
W008

W015 D527
R8120

L503
W023

D519

IC501
D515

C8115
W014

C536 R51
1
R508

C8114 C522 W004

W019 C520 R514
A30C5
D8103

C528
D8105

G
J8101

R510_1
R8105
R8103

D528
L505 Q502
R534
R530
R528

C8112 C526 D521

C

D522
P5

W009 W010
03

W011
D520
R529_1

C517
Q504
D523
W005

L8101
D536

D8101 D8104 C519

E CP502
D531 D535
D533
C8113

72 DV-610AV-S
1 2 3 4
 SIDE B
5

5
Q501
R504
C508 R523
R515 C540
R527 R506
R513 C503
R538
R518

Q506
R539
R517

R516

Q512
Q513
R537
R548

Q503
R544
6

6
R531

R536
C541

B502

DV-610AV-S
R547
R540

Q511
R543 R541 R509
R542
POWER PCB ASSY
7

7
Q509
R525

Q505
R545
C524
R546 C8101
R519
R8108
C501
C8105 R8104
R8101
R526
Q8102

R8112 R8114
R8106
Q8101

C8111
R8121 C8106 R8109 C8116

Q8103
R8107 R8115
DPG017A

R8113 R8102
C8103 C8107
Q8104

C8119 B8101 R8110 R8111

R8122
Q8105

R8123
C8120
R8124
8

8
73
SIDE B

F
E
B
A

D
C
 1 2 3 4

12. PCB PARTS LIST

NOTES: - Parts marked by NSP are generally unavailable because they are not in our Master Spare Parts List.
A - The > mark found on some component parts indicates the importance of the safety factor of the part.
Therefore, when replacing, be sure to use parts of identical designation.
- When ordering resistors, first convert resistance values into code form as shown in the following examples.

Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47 k ohm (tolerance is shown by J = 5%,
and K = 10%).
560 56 101 561 ................................................................... RD1/4PU 5 6 1 J
47 k 47 103 473 ................................................................... RD1/4PU 4 7 3 J
0.5 R50 ................................................................................................. RN2H R 5 0 K
1 1R0 ................................................................................................. RS1P 1 R 0 K
Ex.2 When there are 3 effective digits (such as in high precision metal film resistors).
5.62 k 562 101 5621 ................................................................. RN1/4PC 5 6 2 1 F

- Meaning of the figures and others in the parentheses in the parts list.
B
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding PC board.
IC 301 (A, 91, 111) IC NJM2068V

Mark No. Description Part No. Mark No. Description Part No.
LIST OF ASSEMBLIES
1..DVD MT PCB ASSY A2L502A130

1..OPERATION PCB ASSY A2L502A270 OPERATION PCB ASSY

(WYXZT5,WVXZT5)* SEMICONDUCTORS
IC 651 IC PT6315 IF4K063150
1..OPERATION PCB ASSY A2L506A270
C (WSXZT5)* SWITCHES
SW 652-667SWITCH TACT 0504R01T38
> 1..POWER PCB ASSY A2L502A240
OTHERS
(*) A2L502A270 and A2L506A270 have same service parts.
CP 602 CONNECTOR PCB SIDE 06G5AA1002
But they are NOT COMPATIBLE.
V 651 TUBE FLUORESCENT 096F80R401
OS 651 REMOTE RECEIVER 077Q040004

Mark No. Description Part No.

POWER PCB ASSY
DVD MT PCB ASSY RESISTORS
SEMICONDUCTORS > R 511 R,FUSE 68 OHM 1/4W R65584680J
D
IC 2301 IC AM5766 I1UFV5766S
IC 4001 IC S-24CS04AFJ-TB-GE I5HJ0S04A0 OTHERS
IC 4002 IC MT1389EXE/S-L IC8K0389SX J 8101 SOCKET, 21PIN 063D100050
IC 4003 IC R3112N291A-TR-FA IE1F0291A0 J 8102 RCA JACK 060R401122
IC 4004 IC ES29LV160EB-70TG S2L502AF01 CP 8102 CORD CONNECTOR 06E8223401
OS 8101 OPTICAL DEVICE 07AA000011
IC 4005 IC M12L64164A-5TG IF9J0164AE
IC 4006 IC LD1117AL-ADJ-AA3-A-R I1YF9117A0
IC 4007 IC R5523N001B-TR-F I1ZF0N0010
IC 4009 IC BA00BC0WFP-E2 I07F0C0WF0
IC 5902 IC PQ1K503M2ZPH I0GF9K5030

E IC 7301 IC LA73054-TLM-E I03FG30540

IC 7302 IC SN74CBT3257PWR I5CJ032570
IC 8001 IC TC7SHU04FU I55F004FU0
IC 8003-8005 PCM1742KE/2K I17F042KE0
IC 8008 IC RC4580IDR I04J045800

OTHERS
J 7302 RCA JACK 060R451013
J 7304 JACK 063R700013
J 8001 RCA JACK 060R451012
J 8002 RCA JACK 060R451014
CP 5901 CONNECTOR PCB SIDE 06GEYJ3048

F X 4001 CRYSTAL (27 MHz) 100GT02720

74 DV-610AV-S
1 2 3 4