Scribd
Upload
98 views

P2 Series InstallationlManual

This document provides installation instructions for the Series P2 Mobile Piston Pump in 3 pages or less. It includes checking the model code and pump rotation, connecting suction, pressure and drain lines, filling the pump case with oil prior to start up, and guidelines for hydraulic fluid type, cleanliness, viscosity, and operating temperature.

Uploaded by

xxsh
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
98 views

P2 Series InstallationlManual

This document provides installation instructions for the Series P2 Mobile Piston Pump in 3 pages or less. It includes checking the model code and pump rotation, connecting suction, pressure and drain lines, filling the pump case with oil prior to start up, and guidelines for hydraulic fluid type, cleanliness, viscosity, and operating temperature.

Uploaded by

xxsh
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

INSTALLATION MANUAL

SERIES P2
MOBILE PISTON PUMP

ECN 133814 RELEASE TO PR STATUS


ECN 134356 CHANGED TO REV. A

APPROVED BY DATE TITLE SHEET

M. KUEHNE 04NOV04 INSTALLATION MANUAL P2 1 OF 6


DRAWN BY DATE PART NO. REV. STATUS

J.LONGERICH 04NOV04 P2-000-3921 A PR


1. Check model code / compare with your paper work

Nameplate of pump Ordering / sales acknowledgement

2. Check rotation of pump

Clockwise rotation (right) - side ported pump Counter clockwise rotation (left)-side ported pump

Clockwise rotation (right) - rear ported pump Counter clockwise rotation (left)-rear ported pump
P2060* and P2075* only P2060* and P2075* only

APPROVED BY DATE TITLE SHEET

M. KUEHNE 04NOV04 INSTALLATION MANUAL P2 2 OF 6


DRAWN BY DATE PART NO. REV. STATUS

J.LONGERICH 04NOV04 P2-000-3921 A PR


3. Suction, pressure and drain line connection

Minimum pump inlet pressure under static and dynamic load : pin min = 0,8 bar absolute

Maximum pump inlet pressure : pin max = 10 bar

pressure port
pressure
drain port gauge port

suction optional
suction port drain port
gauge port

APPROVED BY DATE TITLE SHEET

M. KUEHNE 04NOV04 INSTALLATION MANUAL P2 3 OF 6


DRAWN BY DATE PART NO. REV. STATUS

J.LONGERICH 04NOV04 P2-000-3921 A PR


Arrangement outside tank. Arrangement outside tank.
Fill pump case with oil before start. Fill pump case with oil before start.
Do not restrict suction line. Do not restrict suction line.

Arrangement outside tank.


Arrangement outside tank. Fill pump case with oil before start.
Fill pump case with oil before start. Do not restrict suction line.
Do not restrict suction line.
Preferred arrangement for best suction
characteristic and low noise level operation.

APPROVED BY DATE TITLE SHEET

M. KUEHNE 04NOV04 INSTALLATION MANUAL P2 4 OF 6


DRAWN BY DATE PART NO. REV. STATUS

J.LONGERICH 04NOV04 P2-000-3921 A PR


4. Drain line connection

OPTION !
Connect highest drain port with a separate line
reduced in size for purging the air out of the
case

AND

secondary drain port has to be connected as


main drain line.

WARNING !
Do not combine drain lines.

Maximum continuous case pressure :

pcase = 0,5 bar

Maximum intermittent peak case pressure :

pcase = 2 bar

WARNING !
Do not restrict drain line.

A restricted drain line can damage the pump.

APPROVED BY DATE TITLE SHEET

M. KUEHNE 04NOV04 INSTALLATION MANUAL P2 5 OF 6


DRAWN BY DATE PART NO. REV. STATUS

J.LONGERICH 04NOV04 P2-000-3921 A PR


5. Start up

Prior to start up, the pump case must be filled with hydraulic fluid (use case drain port).
Initial start up should be at zero pressure with an open circuit to enable the pump to prime.
Pressure should only be increased once the pump has been fully primed.

6. Hydraulic Fluid

6.1. Recommended fluids

Normal mineral oil


Premium hydraulic fluid / HLP oil
Biodegradable hydraulic fluid
Synthetic hydraulic fluid
Fire resistant fluids

Remark :
Maximum system pressure reduced to 210 bar for water based fluids.
Bearing life time reduced to 25 % by using water based fluids.

6.2. Cleanliness level

Recommendation for maximized component life and reliability :

Class 21 / 18 / 14 according to ISO 4406

6.3. Viscosity range

Minimum viscosity for short periods : 10 mm/s ( cSt )

Normal operating viscosity : 15 cSt 40 mm/s ( cSt )

Maximum viscosity for short periods : 1000 mm/s ( cSt )

7. Temperature

7.1. Check hydraulic fluid specification for chemical resistance of seal material !

7.2. Check temperature range of seal material


and compare with maximum system and ambient temperature !

N Nitrile, single shaft seal -40C to +90C

D Nitrile, double shaft seal -40C to +90C

V Fluorocarbon, single shaft seal -15C to +150C

T Fluorocarbon, double shaft seal -15C to +150C

Remark :
The highest fluid temperature will be at the drain port of the pump,
up to 20C higher than in the reservoir.

APPROVED BY DATE TITLE SHEET

M. KUEHNE 04NOV04 INSTALLATION MANUAL P2 6 OF 6


DRAWN BY DATE PART NO. REV. STATUS

J.LONGERICH 04NOV04 P2-000-3921 A PR

You might also like