Henkel The Solution Provider

Truly Integrated, Truly International

Surface Engineering
Solutions
Henkel is a world-wide operating, market-driven specialist in brands and technologies with
affiliates in over 75 countries, providing technology competence from one single source. People in
125 countries around the world trust in brands and technologies from Henkel. The portfolio
Rebuild, Repair and Protect
includes adhesives and sealants, products for direct glazing, corrosion protection, underbody and
anti-chip coating, sound deadening solutions, body care and many other speciality chemicals. Industrial Equipment
Strong brands with proven and trusted names, such as Loctite Nordbak and Loctite Hysol
Polymer Composites, are incorporated into this common platform and have long been the key to
Henkels success.

Around the world, Henkel also has an extensive commitment to motorsports. In 2004, the Henkel
logo appeared for the first time on the rear-wing of the Team McLaren Mercedes race cars,
thereby continuing the technical association with the team. The Dakar Rally is the latest in a long
line of top-level competitive motor sport events in which Henkel has been involved. Loctite and
Teroson products from the Henkel portfolio have demonstrated their capability to provide fast and
reliable repairs in the most difficult situations and have proved that they are more than a match for
the worlds most demanding conditions.

Meets all Needs

At Henkel, we understand plant maintenance and the problems that you face in ensuring
reliability, safety and durability. We see our duty as being an active partner in providing products
that are going to help in the cost-efficient, trouble-free and effective maintenance and repair of
industrial plant and equipment.

We're here to ensure that you receive all the help and support you need.
All you have to do is ask.

For more information on the complete range of Loctite products from the Henkel portfolio, please
visit www.loctite.com, where you can download catalogues, data sheets, technical papers and
application examples.

Henkel Loctite Adhesives Ltd

Technologies House
Wood Lane End
Hemel Hempstead
Hertfordshire HP2 4RQ
Tel. 01442 278100 The data contained herein are intended as reference only. Please contact your local Henkel Technical Support Group for assistance and recommendation on
Fax 01442 278071 specifications for these products.

www.loctite.co.uk designates a trademark of Henkel KGaA or its affiliates, registered in Germany and elsewhere Henkel KGaA, 2007
2 1
 Introduction Table of Contents

Advanced Solutions Surface Preparation 4

Metal Surface Repair and Rebuild 6
Loctite Nordbak and Loctite Hysol Polymer Composites rebuild, repair
and protect industrial equipment and surfaces, extending equipment life, Protecting Surfaces 10
improving efficiency and minimising down time.
Technical Reference 14
Tried and proven for over 50 years, Loctite Nordbak and Loctite Hysol Polymer Composite

products offer maintenance solutions to the problems caused by wear, abrasion, chemical attack, Application Case Histories 14
erosion, corrosion, impingement and mechanical damage.
Surface Preparation Grades of Blast 18
With extremely hard fillers, Loctite Nordbak and Loctite Hysol Polymer Composite products

have excellent wear resistance and superior adhesion. They are designed for specific service
Environmental Conditions for Effective Coating 19
conditions and to protect and extend the service life of a wide range of plant areas and plant Application Tips 20
equipment. Their key advantage is their capability to create a sacrificial and renewable working
surface, protecting the structural integrity of the original substrate. Troubleshooting Guide 21
Henkel offers a complete range of Loctite Nordbak and Loctite Hysol Polymer Composite Properties Chart 22
products to treat, rebuild and protect your assets in the harshest industrial environments.

Your Professional Partner for Industrial Maintenance Solutions

With Loctite branded products, Henkel offers one of the worlds leading and proven industrial
maintenance technologies, for effective solutions to specific problems in a wide range of industrial
maintenance environments.

Our highly experienced Henkel Application Engineers are committed to providing the highest level
of technical support and assistance in the industry. Working closely with local industrial suppliers
and selected Engineering Service Agents, our Application Engineers provide full process support,
from maintenance assessment to implementation of solutions.

With Henkel, you benefit from a trusted partner who is committed to your success.

2 3
 Surface Preparation

Correct surface preparation is the most important factor

affecting the total success of any surface treatment.
Without suitable surface profile and surface cleanliness
coating systems will quickly fail.

Surface Cleanliness
Chemical contaminants that are not readily visible, such as chlorides
and sulphates, attract moisture through coating systems resulting in
premature failure. It is fundamentally important to chemically clean all
substrates with an industrial strength cleaner and degreaser. Loctite
Polymer Composite product applications require a surface profile of
SP 2.5 to 3 (refer to page 18).

Loctite 7840 multi-purpose cleaner & degreaser

Loctite 7840 Cleaner and degreaser

Before Abrasive Blasting
Biodegradable, solvent free, non-toxic and non flammable, diluted
with water. Rated USFA-C1.
Meets the requirements of a wide range of industrial cleaning
applications. Removes grease, oil, cutting fluids.

Colour Blue

Did you know? Pack Size 750 ml trigger spray, 5 litre can, 20 litre drum

Surface Profile
Surface profile is
Abrasive blasting not only removes visible surface rust and
inadequate, providing Loctite 7063 Cleaner and degreaser
contaminates, but also creates a surface roughness ideal for a poor anchor pattern,
bonding to. This surface roughness is known as surface profile. resulting in adhesive After Abrasive Blasting
Bad Profile failure. No residue, rapid flash off cleaner ideal for removing greases and
Surface profile is critical to coating performance as it improves contaminates prior to adhesive bonding, coating and sealing
adhesion by increasing surface area and providing a keyed applications. Compatible with metal, glass, rubber, most plastics Loctite 7063 multi-purpose cleaner & degreaser
anchor pattern. and painted surfaces.
Surface profile provides
a very good anchor
Surface profiles will vary depending on the type and size of pattern, maximizing Colour Colourless/non-residue
abrasive particles, equipment and technique utilized. It is critical coating adhesion.
Correct Profile Coating thickness is Pack Size 400 ml aerosol pump, 10 litre
to achieve the correct profile depth, and product coating
sufficient.
thickness. Loctite Composite applications require a minimum
75 m surface profile. See page 18 for surface specification.
Insufficient coating,
The diagrams on the right hand side illustrate the importance of surface peaks may
the correct surface profile. be exposed to rust
Insufficient Coating and/or contamination.
For further information on surface profile, contact your local Henkel Engineer.

4 5
 Metal Surface
Repair and Rebuild

Loctite Hysol Polymer Composites repair, rebuild

and restore damaged machinery and equipment
permanently and without the need for heat or welding.

Technically advanced and manufactured with over

50 years product and application knowledge, the
range includes putty or pourable formulations for
aluminum, and steel.

Low-shrinking
Can be drilled, tapped, or machined after cure
Loctite Hysol 3472 pourable steel-filled,
Superior adhesion to metal, ceramic, wood, glass, self-levelling 2K-epoxy

and some plastics

Excellent resistance to aggressive chemicals
Choice of mild steel, aluminium, or non-metalic fillers
Create durable repairs

Loctite Hysol 3473 fast curing

Did you know? steel-filled, non-sagging 2K-epoxy

100 % Solids
Loctite Hysol and Nordbak Polymer Composites are formulated with 100 % solids.
This means that unlike solvent based systems Loctite Hysol and Nordbak composites
will have no or low shrinkage when cured.

6 7
 Metal Surface
Repair and Rebuild

Repair or rebuild damaged parts? What material are you filling?

Steel Aluminium Metal before coating

High compressive High temperature Rebuild badly worn metal surfaces

Kneadable Putty Pourable Fast cure Multi purpose
strength resistant before coating*

Solution 3463 3478 A&B 3471 A&B 3472 A&B 3473 A&B 3475 A&B 3479 A&B 7222 7232
Metal Magic Steel Stick Superior metal Metal Set S1 Metal Set S2 Metal Set S3 Metal Set A1 Metal Set HTA

Description 2K-Epoxy 2K-Epoxy 2K-Epoxy 2K-Epoxy 2K-Epoxy 2K-Epoxy 2K-Epoxy 2K-Epoxy 2K-Epoxy
Mix ratio by volume/weight N/A 4:1 / 7.25:1 1:1 1:1 1:1 1:1 1:1 2:1 / 4.8:1 4:1 / 5.33:1
Working life 3 min. 20 min. 45 min. 45 min. 6 min. 45 min. 40 min. 30 min. 45 min
Fixture time 10 min. 180 min. 180 min. 180 min. 15 min. 180 min. 150 min. 180 min 120 min
Shear strength (GBMS) 6 N/mm 2
17 N/mm 2
20 N/mm 2
25 N/mm 2
20 N/mm 2
20 N/mm 2
20 N/mm 2
10 N/mm 2

Compressive strength 82.7 N/mm 2
125 N/mm 2
70 N/mm 2
70 N/mm 2
60 N/mm 2
70 N/mm 2
90 N/mm 2
80 N/mm 2
103 N/mm2
Operating temperature -30 to +120 C -30 to +120 C -20 to +120 C -20 to +120 C -20 to +120 C -20 to +120 C -20 to +190 C -30 to +105 C -30 to +205 C
Pack sizes 50 g, 114 g 452 g tub kit 500 g tub kit 500 g tub kit 500 g tub kit 500 g tub kit 500 g tub kit 1.4 kg kit 1 kg kit

* Loctite Nordbak 7222 Wear

Resistant Putty or Loctite Nordbak
7232 HighTemperature Wear
Resistant Putty, are used prior to
applying protective Loctite
Nordbak composite coatings.

Please see page 12 for product
details.

Loctite 3463 Loctite Hysol 3478 A&B Loctite Hysol 3471 A&B Loctite Hysol 3472 A&B Loctite Hysol 3473 A&B Loctite Hysol 3475 A&B Loctite Hysol 3479 A&B Loctite Nordbak 7222 Loctite Nordbak 7232
Sets in 10 minutes. Steel filled A ferro-silicon filled 2K-Epoxy with General-purpose steel-filled, Pourable, steel-filled, self levelling Fast curing, steel filled, non- A non sagging, heavily reinforced, A non sagging, heavily reinforced, Ceramic filled, non rusting, A high temperature silicon carbide
kneadable Stick. Adheres to outstanding compression strength. non-sagging 2K-Epoxy. Cures 2K-Epoxy. Recommended for sagging, 2K-Epoxy. Reaches aluminium powder filled 2K-Epoxy. aluminium powder filled 2K-Epoxy. trowelable putty. Excellent wear filled, trowelable putty that resists
damp surfaces and cures under Ideal for renewing surfaces sub- to a metal-like finish. Used to casting into hard to reach areas, functional cure in approx. 10 Easily mixed and moulded to form Easily mixed and moulded to form and abrasion resistance. Cures wear, and provides a smooth
water. Chemical and corrosion jected to compression, thrust, rebuild worn metal parts. anchoring and levelling, forming minutes. Ideal for emergency odd shapes if required. Cures to a odd shapes if required. Cures to a to a smooth, low friction finish surface. Used as a wear-resistant
resistant. Can be drilled, filed and impact and harsh environments. moulds and parts. repair and repairing worn metal non-rusting, aluminium-like finish non-rusting, aluminium-like finish for equipment exposed to wear, coating and filler.
painted. ANSI/NSF Standard 61 Typical Applications: parts to prevent downtime. ideal for repairing aluminium ideal for repairing aluminium erosion and cavitation.
Typical Applications: Seal cracks in tanks, castings, Typical Applications: parts. parts. Typical Applications:
Typical Applications: Rebuilding keyways and spline vessels and valves Form moulds, fixtures and Typical Applications: Typical Applications: Filling cavitation or providing
Emergency sealing of leaks in assemblies Patch non-structural defects in prototypes Repair holes in fuel and gas Typical Applications: Typical Applications: Repair pitting caused by protective coating on pump
pipes and tanks Rebuilding worn cylindrical steel casings Repair threaded parts tanks Repair aluminium castings Repair aluminium castings cavitation or corrosion impellers and in pump housings
Smoothes welds joints with a shaft mounted Make moulds and jigs for odd Repair pipes and tanks Renew stripped threads Repair cracked or worn Repair cracked or worn Repair and coat pump Repairing wear or providing
Repairs small cracks in component like bearings, clamp shaped parts Repair and level broken metal Repair leaks in pipes and aluminium parts aluminium parts impellers protective coating in pipe
castings connections, tensioning Resurface worn air seals components and parts elbows Make aluminium dies Make aluminium dies Add protective coating to systems
Fills over-sized bolt holes elements or gear wheels Repair leaks in storage tanks Repair stripped aluminium Repair stripped aluminium pipes, elbows, pumps, Repairing and resurfacing valve
Repair pitting caused by
Rebuilding bearing seats cavitation and/or corrosion Rebuild worn steel parts threads threads transitions, butterfly valves, parts
deflection plates and tanks Filling areas subjected to sliding
wear and abrasion
Repairing or providing protective
coating to turbine blades

8 9
 Protecting Surfaces

Loctite Nordbak Polymer Composite Compounds

utilize the superior wear properties of ceramic and
the convenience of two-part epoxies to protect
equipment like pumps, chutes, and augers in harsh
industrial environments. Available in trowelable
and brushable formulations with special fillers for
tough conditions, Loctite Nordbak products stand
up to every corrosion, abrasion, and wear problem
you can encounter, and are ideal for all those
large-scale repairs that have to last.

Restore worn surfaces, use on new parts to extend life

Provide superior protection from environmental impact
Eliminate and break corrosion / erosion cycle
Non-shrinking and non-sag formulations
High compressive strength
Good chemical resistance

Tips & Tricks Wide range tailored to specific applications

Preventing Flash Rusting Wear Indicator standard pressure pot or airless

In high humidity conditions, flash rusting When applying two coats of Loctite systems with a tungsten tip orifice size
of a newly prepared metal surface can Nordbak Brushable Ceramic, a different of 0.19 to 0.21 mm and a maximum
develop within minutes, causing colour can be used for each grey and hose length of 3 to 5 meters. Depending
contamination which will need to be white. When the first coat begins to on climatic conditions and technique, up
removed again before a coating is wear the second coat colour will show to four of the 5.4 kg kits can be sprayed
applied. through, providing an accurate visual through the line before cleaning is
The application of a thin coat of Loctite indicator of wear. required. This will cover approximately
Nordbak Brushable Ceramic applied as 20 square metres. A solvent such as
soon as possible after preparing a metal Pressure Spraying industrial paint thinner or acetone
surface will prevent flash rusting. Loctite Nordbak Chemical Resistant should be used to clean equipment.
Concentrate on edges, corners and hard Coating is suitable for brush, roller and Cleaning may be required more
to reach areas first and then fill in the pressure spray application. Pressure frequently if the product and ambient
remaining areas until totally covered. spraying Loctite Nordbak Chemical temperatures are higher, to prevent the
Resistant Coating can be achieved with line being clogged by curing product.

10 11
 Protecting Surfaces

Protect against particle abrasion or chemical attack?

Coarse particle Fine particle Chemical attack

Resists abrasion & Resists fine particle Brushable protective

Resists abrasion Resists impact & Resists fine Brushable protective Chemical resistant
corrosion at high abrasion at high coating at high
& corrosion sliding abrasion particle abrasion coating brushable coating
temperature temperature temperature

High Temperature High Impact High Temperature High Temperature Chemical Resistant
Wearing Compound Pneu-Wear Brushable Ceramic
Wearing Compound Wearing Compound Pneu-Wear Brushable Ceramic Coating

Solution 7218 7230 7219 7226 7229 7227/7228 7234 7221

Colour Grey Grey Grey Grey Grey Grey/White Grey Grey
Temperature range - 28 to +120 C - 28 to +230 C - 30 to +120 C - 29 to +120 C - 30 to +230 C - 29 to +95 C - 29 to +205 C - 30 to +65 C
Mix ratio by volume 2:1 4:1 2:1 4:1 4:1 2.75:1 / 2.8:1 2.6:1 2.3:1
Working time 30 min. 30 min. 30 min. 30 min. 30 min. 30 min. / 15 min. 30 min. 20 min.
Cure time 7 hrs 7 + 2 hrs Post Cure 6 hrs 6 hrs 6 + 2 hrs Post Cure 6 hrs / 5 hrs 8 + 3 hrs Post Cure 16 hrs
Recommended layer thickness min. 6 mm min. 6 mm min. 6 mm min. 6 mm min. 6 mm min. 0.5 mm min. 0.5 mm min. 0.5 mm
Pack sizes 1 kg, 10 kg 10 kg 1 kg, 10 kg 1 kg, 10 kg 10 kg 1 kg 1 kg 5.4 kg

Badly worn surfaces are rebuilt using Loctite Nordbak 7222

Wear Resistant Putty or Loctite Nordbak 7232 High
Temperature Wear Resistant Putty, prior to applying protective
Loctite Nordbak composite coatings.

Please see page 9 for product details.

Refere to your Henkel Engineer for further information.

Loctite Nordbak 7218 Loctite Nordbak 7230 Loctite Nordbak 7219 Loctite Nordbak 7226 Loctite Nordbak 7229 Loctite Nordbak 7227/7228 Loctite Nordbak 7234 Loctite Nordbak 7221
A two-part, trowelable, ceramic A two-part, ceramic filled epoxy A two-part, rubber modified, A two-component epoxy, filled A two-part, small ceramic bead An ultra-smooth, ceramic A brushable two-part epoxy This advanced two-part epoxy is
filled epoxy designed to protect, paste designed to protect, rebuild ceramic filled epoxy paste that with small ceramic beads and filled epoxy putty, non-sag and reinforced epoxy that provides designed to protect against designed to protect equipment
rebuild and repair high wear areas and repair high wear areas of offers wear resistance properties silicon carbide for protecting trowelable. Designed to protect a high gloss, low friction coating turbulence and abrasion under against extreme chemical attack
of processing equipment. Non- processing equipment. and impact resistance. processing equipment from fine equipment from fine particle to protect against turbulence and extreme heat. and corrosion. It forms a smooth,
sagging and suitable for overhead Requires post curing for ultimate Recommended for areas exposed particle abrasion. This trowelable abrasion in dry, high temperature abrasion. Seals and protects equip- glossy, low-friction finish that
applications and irregular surfaces. performance and temperature to abrasion and impact. Non- and non-sag epoxy is suitable for applications. Requires post curing ment from corrosion and wear. Typical Applications: protects against turbulence and
resistance. sagging and suitable for overhead providing abrasion resistance on for ultimate performance and Protecting exhausters from cavitation. It can be applied by
Typical Applications: applications and irregular surfaces. overhead and vertical surfaces. temperature resistance. Typical Applications: cyclic heat and corrosion brush or pressure sprayed.
Cyclone and separator bodies Typical Applications: Lining tanks and chutes Repairing heat exchangers
Dust collectors and exhausters Cyclone and separator bodies Typical Applications: Typical Applications: Typical Applications: Rudders and pintle housings and condensers Typical Applications:
Pump liners and impellers Dust collectors and exhausters Dredge pump liners Elbows Providing protective lining in Heat exchangers butterfly Lining tanks and chutes Impellers, butterfly valves,
Pump liners and impellers Flumes and troughs Chutes and hoppers pneumatic conveyor systems valves and cavitated pumps
Fan blades and housings Repairing butterfly valves
Fan blades and housings Pump impellers Cyclones Repairing and providing Condensers Rudders and pintel housings
Chutes and hoppers
Vibrating feeders Air ducts abrasion resistance in: Lining tanks and chutes
Elbows and transition points Chutes and hoppers Repairing cooling pump
- elbows
Exhausters Material transfer chutes/ impellers Lining chemical containment
- hoppers
hoppers areas
- cyclones
- dust collectors
12 13
 Application Case Histories Application Case Histories
Metal Surface Repair and Rebuild Protecting Surfaces

Pump Rebuild Pump Protection in Copper Mine

So bad was the condition of the split case pump (pictured right) that In a copper mine, plant equipment is exposed to
replacement was considered the most viable option. However, using Loctite extremely harsh conditions. Damage or failure to plant
Nordbak products, the pump was repaired and returned to service with components and equipment can cause very expensive
superior protection qualities and at a lower cost. downtime. In this Polish copper mine pumps that had
Before any repairs began the surface was thoroughly perpared, and then a been operating without protective coatings were exposed
thin coat of Loctite Nordbak Brushable Ceramic was applied to prevent to extreme wear and corrosion (Pic. 1).
flash rusting or further contamination. Next, a wire frame was used to To prevent further damage, increase efficiency and
recreate the shape of the centre web surface which had totally eroded. prolong service life, all new pumps are now coated with
This frame was then filled with Loctite Nordbak 7222 Wear Resistant Putty. Loctite Nordbak Polymer Composite Compounds.
The wear ring channels were then rebuilt by applying Loctite 3478 Superior
Metal to the affected area. Next the rings were secured into position and Pitting and erosion Reclaiming totally Pic.1: Corrosion and erosion were clearly evident Pic.2: Surface was abrasive blasted to surface After surface preparation (Pic. 2), the casing and
was clearly evident eroded surface profile of 75 m
excess product that was displaced was removed and smoothed. The rings impellers are coated with Loctite Nordbak 7227
were precoated with a release agent and when cured were removed leaving Brushable Ceramic Grey (Pic. 4). In places exposed to
perfectly engineered channels. wear a 1.5 mm layer of ceramic filled epoxy has been
Finally pits were filled with Loctite Nordbak 7222 Wear Resistant Putty and applied (Pic. 3). To maximise protection the pumps are
the entire surface sealed with Loctite Nordbak 7227 Brushable Ceramic, checked and re-surfaced where necessary, once a year.
forming an ultra smooth low friction surface.

Restored and ready

for assembly

Fan Impellers in Steel Mill Pic.3: Application of Loctite 7227 Pic.4: Full surface coated, then after partial cure
to casing and Cutwater the second coat was applied

Application steps:
1. Removal and cleaning of any grease, oils
2. Drying of the impeller surface
Did you know?
3. Abrasive blasting of impeller surface
(SP 2.5 - 3; refer to page 18) Traditional methods vs. modern solutions
4. Removal of dust from the surface Traditional repair methods such as hard face welding are time consuming and expensive. Alternatively, Loctite Nordbak composite
5. Application of two coats of Loctite products are easily applied and offer superior compressive strength and protection qualities. Consider the following comparison of the
Nordbak 7227 process required to repair a 600 cm2 surface area;
6. 24-hour cure time allowed
Loctite Nordbak Wearing Compound Hard Face Weld
Two impellers before abrasive blasting First impeller is coated
Step 1: Prepare surface Step 1: Prepare surface
Step 2: Mix resin and hardener Step 2: Preheat rods & substrate
In coke production in steel mills, big fans are in operation, 24 hours a day. Their impellers are in contact with air coming from the Step 3: Apply to surface with trowel Step 3: Lay 6 mm x 3 mm beads x 210 mm long.
coke production, containing corrosive gases with very fine dust. Corroding very quickly, the impellers in this Slovakian Steel Mill TOTAL LABOUR: 1 HOUR Overlap each bead by 50 %
needed repainting regularly, hence interrupting costly production. Loctite Nordbak 7227 is able to protect against these severe Step 5: Lay second pass of beads to achieve 6 mm
conditions. When coated with Loctite Nordback 7227 the working life of the impellers was increased to more than two years. + Additional benefits thickness. Total of 176 passes.
No specialised labour required Step 6: Relieve stress caused by application of heat
No heat distortion of the substrate TOTAL LABOUR: 8 HOURS

14 15
 Application Case Histories Application Case Histories
Protecting Surfaces Pump Efficiency Improvement

Detergent Mixing Tank 600 Megawatt Electricity Consumption Savings in a Year!

Due to the cavitation effects and wear on the impeller and casing, this 1,400-
kilowatt water circulation pump in a Chinese petrochemical plant was losing its
efficiency, and could break down anytime. It would cost a fortune to replace
it with a new pump.
In addition to the anti-abrasion and anti-cavitation capabilities, the smooth
surface of Loctite Nordbak 7227 Brushable Ceramic coating has minimized
Mechanical removal of rusted Abrasive blast to surface profile of Application of Loctite 7227 Full surface coated, then after partial After 24 hrs, the tank was ready resistance to the water flow inside the pump. As a direct result, current draw
patches and drying of inner surface 75 m and surface cleanliness SA 3 on weld lines cure the second coat was applied to be filled dropped to 160 amps from previous 170 amps. The cost saved in terms of
energy consumption alone is EUR 30,000 each year. The pump can now work
to its optimum efficiency. A Loctite solution has brought the customer
Due to the absence of oxygen on the tank surface, corrosion was attacking the stainless steel in this German detergent factory. The
Impeller and casing before repair. The pit holes on the impeller were significant economic and social benefits:
customer needed to prevent this corrosion-erosion cycle from causing leaks in the tank, and seriously interrupting production. Serious wear and cavitations on the reclaimed by using Loctite Superior
In the past, the customer used to resurface the tank inner parts with a product based on vinyl ester resin, needing 7 days cure after impeller Metal Putty. Loctite Nordbak 7227
Brushable Ceramic was coated as
application. With a repair time of 24 hrs, Loctite Nordbak 7227 Brushable Ceramic has not only prevented further corrosion and the second layer.
achieved protection against turbulence and abrasion, but has provided a cost effective solution.

A Total of 2,400 Megawatt Energy Saved

within 7 Months and Productivity Increased by
8.06 % in the plant, reported by local
newspaper. Loctite contributed 1,200
Butterfly Valve Casing after repair. Megawatt saving in a year for 2 pumps!

A butterfly control valve at a Waste Water Treatment Plant was corroded

and therefore unable to seal effectively. The components were abrasive
blasted and a thin coat of Loctite Nordbak 7228 Brushable Ceramic
3 amps less current!
(White) applied to seal the newly cleaned surface. The rough and corroded
This 20" pump is used to pump potable water to fill three gravity feed
edges of the valve were then re-profiled with Loctite Nordbak 7222
reservoirs that supply drinking water to Brisbane Australia. The pump has
Wear Resistant Putty before a final coat of Loctite Nordbak 7227
been in service for many years without any major overhaul. The refurbishment
The corroded butterfly valve before and after repair Brushable Ceramic (Grey) was applied. The two coat colours can be
program was to reclaim and rebuild the worn housing and impeller of the
utilised as a wear indicator for any future repairs or maintenance. The
pump. After recommissioning of the pump, it runs smoother and quieter. The
butterfly valve was returned to service within 1 day.
use of Loctite coatings has increased water flow and draws 3 amps less
current. All these factors will contribute to a more cost effective and
higher efficiency unit.
Top cap and bronze impeller before repair. The first step is to abrasive blast
these parts to SA-3 White Blast 75 m profile.
Pipes & Ducts
Pipes and ducts are a common wear point in almost every industrial plant.
The coke plant pictured was forced to repair or replace duct elbows every
3 months at significant cost of labour and material.
After application of Loctite Nordbak 7229 Pneu-Wear, the same pipe
elbows remained in service for 3 years without need for further repair.
Loctite Nordbak 7227 Brushable Ceramic
Grey applied to seal the blast. Fill the corroded Repair the worn and corroded shaft using Loctite 3478 Superior Metal. After its
Coke Plant and abraded areas using Loctite Wear 7222 cured, machine it to complete the repair. Coat all parts with Loctite Nordbak
Pipe Elbow Resistant Putty. 7228 Brushable Ceramic White (certified for use in contact with drinking water).

16 17
 Surface Preparation Grades of Blast Environmental Conditions for Effective Coating

Loctite composite applications require a minimum 75 m surface profile (see page 4) and a 2.5 blast class. It is critical to the success of most coating systems that the surface is completely free of moisture prior to and during
product application and curing.

Rust Grade Blast Class Dewpoint

A Steel with mill scale layer intact and very minor, 1 (SP-7/N4) Very light over clean with removal of loose Condensation of water (dew) from the atmosphere on to the surface will occur, given the right conditions. For a given set of
or no rusting surface contaminants conditions, the temperature at which condensation will occur is called the dewpoint. As long as the surface temperature is 3 C
B Steel with spreading surface rust and the mill scale 2 (SP-6/N3) Substantial blast clean with wide spread, visible (or more) above the dewpoint temperature, it is generally considered safe to coat as far as risk of condensation is concerned.
commenced flaking contaminate removal and base metal colour
C Rusty steel with mill scale layer flaked and loose or lost but appearing
only minor occurrence of pitting 2.5 (SP-10/N2) Intensive blast clean leaving shading grey metal
D Very rusty steel with mill scale layer all rusted and extensive with only contaminates Atmospheric conditions for coating application
occurrence of pitting 3 (SP-5/N1) Complete blast clean with consistent metal colour
all over and no visible contaminates 16

Unblasted Blast Class 1 Blast Class 2 Blast Class 2.5 Blast Class 3
14
Rust Grade A

12
Do not coat zone
(above guide line)

Air temperature minus substrate temperature

10

DIFFERENCE IN TEMPERATURE (C)

Coa
Rust Grade B

tin
gG
uid
eL
6

ine
4
Rust Grade C

2
Ok to coat zone
(below guide line)
0
Rust Grade D

-2
20 30 40 50 60 70 80 90
RELATIVE HUMIDITY
Blastmaster. Used with written permission from Blastmaster Blastmaster. Used with written permission from Blastmaster

18 19
 Application Tips Troubleshooting Guide

For maximum adhesion Problem Possible causes Suggested solution

After surface preparation, pre-coat the application surface by rubbing the mixed composite
Curing too fast - Air temperature too high Working time and cure time depend on temperature
into the substrate. This technique, called wetting out the surface, helps the repair material
- Application surface too hot and the amount of material being mixed; the higher the
fill all the crevices in the application surface, creating a superior bond between the composite
and substrate. The rest of the mixed product can then be applied over the pre-coat to finish - Composite temperature too hot temperature, the faster the cure. The larger the amount
the application. - Too much material being mixed of material mixed, the faster the cure. To slow the cure
at high temperatures, mix in smaller amounts to prevent
rapid curing and/or cool resin/hardener components
and application surface.
Creating a smooth finish
Smooth out the uncured product with a warm towel for a smooth, glossy finish. A heat gun
can also be used to create a smooth finish.
Curing too slow - Air temperature too cold To speed the cure at low temperatures (< +15 C),
- Composite temperature too cold store at room temperature (+20 C) and/or pre-heat
- Application surface too cold application surface until warm to the touch.

Machining with a lathe

Tooling: Achievable surface roughness:
Loss of adhesion - Surface contamination Prepare surface by grit blasting, if possible. For less
- Tipped tooling with hard metal insert or diamond Example Loctite Hysol 3478 Superior
insert, like CBN Metal or Brushable Ceramic - Surface too smooth severe application, roughening the surface with hand
(Loctite Nordbak 7227/7228) tools is suitable. Solvent clean with a residue-free
Machining parameters: - Ra ~5 m; Rz ~30 m cleaner such as Loctite 7063 Cleaner and degreaser,
- Cutting speed: 125 m/min
- In feed: 0.08 mm/RPM
non-residue or Loctite 7840 Cleaner & degreaser,
- No cooling/lubricating is necessary biodegradable and solvent free. Product should be
applied as soon as possible after surface preparation to
avoid surface rust or contamination.
Machining with the grinding machine
For further details please refer to page 4/5.
Tooling: Achievable surface roughness:
- Silicon carbide grinding disk Example Loctite Hysol 3478 Superior
Machining parameters: Metal or Brushable Ceramic
- Cutting speed: 15 m/sec (Loctite Nordbak 7227/7228)
- Cooling with emulsion during grinding is important - Ra ~0.8 m; Rz ~10 m Excessive shrinking - Too much product being applied Applying too much material at one time will cause
in order not to damage the polymer and cracking or poured resulting in high heat excessive heat build-up, which will cause shrinking and
build-up cracking. Apply material in layers of 25 mm at a time,
allowing the layer to cool before applying the next layer.

Limitations in machining
Polymer Composites filled with abrasive filler Polymer Composites not recommended
with a large diameter cannot be ground or to machine:
machined after cure. - Loctite Nordbak 7218
Try to obtain the required depth of application and - Loctite Nordbak 7219
evenness to avoid unnecessary machining. - Loctite Nordbak 7226
- Loctite Nordbak 7229
- Loctite Nordbak 7230
not machinable machinable

20 21
 Properties Chart

Products Size Coverage Colour Dry service Compressive Shear Page Products Tensile Hardness Working Functional Mix ratio Mix ratio Page
temperature strength strength strength time cure by volume by weight
range ASTM D695 ASTM D1002 ASTN D638 ASTM D-2240 minutes at hours at (R:H) (R:H)
N/mm2 N/mm2 N/mm2 Shore D 25 C 25 C

Loctite 3463 114g tube 45cm2 dark grey -30 C to+120 C 82.7 6 8 Loctite 3463 17 80 3 0.5 N/A N/A 8
Metal Magic Steel 6mm thick Metal Magic Steel
per tube
Loctite Hysol 3471 A&B 500g grey -20 C to+120 C 70 20 8 Loctite Hysol 3471 A&B 60 85 50 12 1:1 1:1 8
tub kit
Loctite Hysol 3472 A&B 500g grey -20 C to+120 C 70 25 8 Loctite Hysol 3472 A&B 65 85 50 12 1:1 1:1 8
tub kit
Loctite Hysol 3473 A&B 500g grey -20 C to+120 C 60 20 9 Loctite Hysol 3473 A&B 45 85 6 1 1:1 1:1 9
tub kit
Loctite Hysol 3475 A&B 500g grey -20 C to+120 C 70 20 9 Loctite Hysol 3475 A&B 50 85 50 12 1:1 1:1 9
tub kit
Loctite Hysol 3479 A&B 500g grey -20 C to+190 C 90 20 9 Loctite Hysol 3479 A&B 60 85 50 12 1:1 1:1 9
tub kit
Loctite Hysol 3478 A&B 454g 500cm2 @ grey -30 C to+120 C 124.1 12.4 8 Loctite Hysol 3478 A&B 38 90 20 6 4:1 7.25:1 8
Superior Metal 6mm thick Superior Metal
per 1kg
Loctite Nordbak 7218 1kg kit 740cm2 @ grey -30 C to+120 C 110.3 12 Loctite Nordbak 7218 90 30 7 2:1 2:1 12
10kg kit 6mm thick
per 1kg
Loctite Nordbak 7219 1kg kit 740cm2 @ grey -30 C to+120 C 82.7 12 Loctite Nordbak 7219 85 30 6 2:1 2:1 12
10kg kit 6mm thick
per 1kg
Loctite Nordbak 7230 10kg kit 740cm2 @ grey -30 C to+230 C 103.4 12 Loctite Nordbak 7230 90 30 Post cure 2hrs 4:1 3.9:1 12
6mm thick at 150C
per 1kg
Loctite Nordbak 7226 1kg kit 740cm2 @ grey -30 C to+120 C 103.4 34.5 13 Loctite Nordbak 7226 85 30 6 4:1 4:1 13
10kg kit 6mm thick
per 1kg
Loctite Nordbak 7229 10kg kit 740cm2 @ grey -30 C to+230 C 103.4 34.5 13 Loctite Nordbak 7229 85 30 Post cure 2hrs 4:1 4:1 13
6mm thick at 150C
per 1kg
Loctite Nordbak 7227 1kg kit 1.2m2 @ 0.5mm grey -30 C to+90 C 86.2 13.8 13 Loctite Nordbak 7227 85 30 6 2.75:1 4.8:1 13
per 1kg
Loctite Nordbak 7228 1kg kit 1.2m2 @ 0.5mm white -30 C to+90 C 86.2 13.8 13 Loctite Nordbak 7228 85 15 5 2.8:1 4.5:1 13
per 1kg
Loctite Nordbak 7234 1kg kit 1.2m2 @ 0.5mm grey -30 C to+205 C 13 Loctite Nordbak 7234 30 Post cure 3hrs at 150C 2.75:1 4.8:1 13
per 1kg and 3hrs at 205C
Loctite Nordbak 7232 1kg kit 750cm2 @ grey -30 C to+205 C 103 9 Loctite Nordbak 7232 59 90 45 Post cure 3hrs at 150C 4:1 5.33:1 9
6mm thick and 3hrs at 200C
Loctite Nordbak 7221 5.4 kg kit 6.8m2 @ grey -30 C to+65 C 69 13 Loctite Nordbak 7221 83 20 16 2.3:1 3.4:1 13
0.5mm per kit
Loctite Nordbak 7222 1.4 750cm2 @ grey -30 C to+105 C 80 10 9 Loctite Nordbak 7222 33.8 89 30 6 2:1 2:1 13
6mm thick
per 1kg

22 23