Scribd
Upload
129 views

How To Check The Default Configuration of Switch S Interface

The document discusses how to view the default configuration settings of interfaces on Huawei S3700/S5700 switches. It explains that the 'display this include-default' command will show both the manually configured and default settings for an ethernet interface. It provides an example output of this command and demonstrates how manually configured settings are now included along with the default settings. It also describes how to clear all configuration on an interface and revert it to only the default settings.

Uploaded by

Hussein Dhafan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
129 views

How To Check The Default Configuration of Switch S Interface

The document discusses how to view the default configuration settings of interfaces on Huawei S3700/S5700 switches. It explains that the 'display this include-default' command will show both the manually configured and default settings for an ethernet interface. It provides an example output of this command and demonstrates how manually configured settings are now included along with the default settings. It also describes how to clear all configuration on an interface and revert it to only the default settings.

Uploaded by

Hussein Dhafan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

how to check the default configuration of

switchs interface
When taking into consideration that default settings are invisible in a configuration file, it is a
good information that Huaweis S3700/S5700 switches have such possibility to display
default settings for ethernet interfaces. The display this include-default command displays
the effective configurations in the current view, including the unchanged default
configurations.

[labnario-Ethernet0/0/1]display this include-default


#
interface Ethernet0/0/1
portswitch
undo shutdown
enable snmp trap updown
undo set flow-stat interval
undo qinq vlan-translation enable
undo mac-address learning disable
port priority 0
port link-type hybrid
port hybrid pvid vlan 1
port hybrid untagged vlan 1
qinq protocol 8100
undo loopback-detect enable
stp enable
undo stp config-digest-snoop
undo stp no-agreement-check
undo stp root-protection
undo stp loop-protection
stp transmit-limit 147
stp point-to-point auto
stp compliance auto
stp instance 0 port priority 128
undo port mux-vlan enable
undo mac-vlan enable
undo ip-subnet-vlan enable
undo rmon-statistics
undo smart-link flush receive
undo smart-link vll-notify enable
undo ntdp enable
undo ndp enable
bpdu enable
undo portal local-server enable
undo dot1x enable
dot1x max-user 256
dot1x port-control auto
dot1x port-method mac
undo dot1x reauthenticate
undo authentication critical eapol-success
authentication max-reauth-req 20
undo mac-authen
mac-authen max-user 256
mac-authen reauthenticate
undo authentication open
undo port-auto-sleep enable
undo port-security enable
undo qinq vlan-translation miss-drop
undo port discard tagged-packet
mac-learning priority 0
undo mac-address flapping trigger error-down
undo mac-address flapping trigger quit-vlan
jumboframe enable 9216
undo set flow-statistics include-interframe
trap-threshold input-rate 100 resume-rate 100
trap-threshold output-rate 100 resume-rate 100
log-threshold input-rate 100 resume-rate 100
log-threshold output-rate 100 resume-rate 100
trap-threshold error-statistics 3 interval 10
carrier up-hold-time 2000
carrier down-hold-time 0
undo port link-flap protection enable
qos wrr
qos queue 0 wrr weight 1
qos queue 1 wrr weight 1
qos queue 2 wrr weight 1
qos queue 3 wrr weight 1
qos queue 4 wrr weight 1
qos queue 5 wrr weight 1
qos queue 6 wrr weight 1
qos queue 7 wrr weight 1
trust 8021p outer
undo dei enable
qos phb marking enable
undo arp anti-attack rate-limit enable
undo arp-miss anti-attack rate-limit enable
undo arp anti-attack check user-bind enable
undo ip source check user-bind enable
unicast-suppression 100
multicast-suppression 100
broadcast-suppression 100
storm-control interval 5
port type nni
undo nd snooping enable
undo nd snooping trusted
undo dhcpv6 remote-id insert enable
undo dhcpv6 remote-id rebuild enable

This command is supported in V100R006C03 and V200R001 software version.

Lets add some configuration to the interface:

[labnario-Ethernet0/0/1]display this
#
interface Ethernet0/0/1
#
return
[labnario-Ethernet0/0/1]port link-type access
[labnario-Ethernet0/0/1]port default vlan 100
[labnario-Ethernet0/0/1]display this
#
interface Ethernet0/0/1
port link-type access
port default vlan 100
#
return

Now use display this include-default command again:


[labnario-Ethernet0/0/1]dis th include-default
#
interface Ethernet0/0/1
portswitch
undo shutdown
enable snmp trap updown
undo set flow-stat interval
undo qinq vlan-translation enable
undo mac-address learning disable
port priority 0
port link-type access
port default vlan 100
qinq protocol 8100
undo loopback-detect enable
stp enable
undo stp config-digest-snoop
undo stp no-agreement-check
undo stp root-protection
undo stp loop-protection
stp transmit-limit 147
stp point-to-point auto
stp compliance auto
stp instance 0 port priority 128
undo port mux-vlan enable
undo mac-vlan enable
undo ip-subnet-vlan enable
undo rmon-statistics
undo smart-link flush receive
undo smart-link vll-notify enable
undo ntdp enable
undo ndp enable
bpdu enable
undo portal local-server enable
undo dot1x enable
dot1x max-user 256
dot1x port-control auto
dot1x port-method mac
undo dot1x reauthenticate
undo authentication critical eapol-success
authentication max-reauth-req 20
undo mac-authen
mac-authen max-user 256
mac-authen reauthenticate
undo authentication open
undo port-auto-sleep enable
undo port-security enable
undo qinq vlan-translation miss-drop
undo port discard tagged-packet
mac-learning priority 0
undo mac-address flapping trigger error-down
undo mac-address flapping trigger quit-vlan
jumboframe enable 9216
undo set flow-statistics include-interframe
trap-threshold input-rate 100 resume-rate 100
trap-threshold output-rate 100 resume-rate 100
log-threshold input-rate 100 resume-rate 100
log-threshold output-rate 100 resume-rate 100
trap-threshold error-statistics 3 interval 10
carrier up-hold-time 2000
carrier down-hold-time 0
undo port link-flap protection enable
qos wrr
qos queue 0 wrr weight 1
qos queue 1 wrr weight 1
qos queue 2 wrr weight 1
qos queue 3 wrr weight 1
qos queue 4 wrr weight 1
qos queue 5 wrr weight 1
qos queue 6 wrr weight 1
qos queue 7 wrr weight 1
trust 8021p outer
undo dei enable
qos phb marking enable
undo arp anti-attack rate-limit enable
undo arp-miss anti-attack rate-limit enable
undo arp anti-attack check user-bind enable
undo ip source check user-bind enable
unicast-suppression 100
multicast-suppression 100
broadcast-suppression 100
storm-control interval 5
port type nni
undo nd snooping enable
undo nd snooping trusted
undo dhcpv6 remote-id insert enable
undo dhcpv6 remote-id rebuild enable
#
return

As you can see, the command shows both manually configured and default settings.

What if you want to come back to the previous settings (default):

Delete configuration one by one:

[labnario-Ethernet0/0/1]undo port default vlan


[labnario-Ethernet0/0/1]undo port link-type

Perform one-touch configuration clearance on an interface:

[labnario]clear configuration interface Ethernet 0/0/1


Warning: All configurations of the interface will be cleared, and its state
will
be shutdown. Continue? [Y/N] :y
Info: Total execute 2 command(s), 2 successful, 0 failed.
[labnario]dis cu int eth 0/0/1
#
interface Ethernet0/0/1
shutdown
#
return

All configuration has been deleted. Note that interface went to shutdown state.

You might also like