Scribd
Upload
434 views

Basic Steps For Foundation Design

This document provides the steps to design a pad footing, including: 1. Calculating the footing size based on allowable bearing pressure and service loads. 2. Checking the ultimate bearing pressure and punching shear. 3. Calculating the reinforcement required for bending and checking shear. It then works through a design example, sizing an 8.41m^2 footing to support a 400mm column with loads of 400kN live and 900kN dead, and checking requirements.

Uploaded by

sujith s p
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
434 views

Basic Steps For Foundation Design

This document provides the steps to design a pad footing, including: 1. Calculating the footing size based on allowable bearing pressure and service loads. 2. Checking the ultimate bearing pressure and punching shear. 3. Calculating the reinforcement required for bending and checking shear. It then works through a design example, sizing an 8.41m^2 footing to support a 400mm column with loads of 400kN live and 900kN dead, and checking requirements.

Uploaded by

sujith s p
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Basic Steps

01. Calculate the size of the footing considering allowable bearing pressure and service load.
02. Calculate the bearing pressure for ultimate loads
03. Check the vertical line shear (shear at face of the column)
04. Check for punching shear
05. Calculate reinforcement for bending
06. Check shear at critical section

Design Example

Live load 400kN

Dead load 900kN

Allowable bearing pressure 175kN

fck 30N/mm2

fyk 500N/mm2

Size of column 400mm

Assume 150kN as footing weight

Calculation of Base Area

Design service load = 1.0Gk + 1.0Qk


= 900 +150 + 400
= 1450kN

Required footing area = 1450/175


= 8.3m2
Hence, provide 2.9m square footing (area 8.41m2)

Calculate Ultimate Loads

Axial load = 1.35Gk + 1.5Gk


= 1.35*900 + 1.5*400
= 1815kN

Ultimate pressure = 1815/(2.9*2.9)


= 216kN/m2
Check for adequacy of footing thickness

Check for Maximum Shear

Assume, footing thickness 500mm, 16mm diameter bars at base and cover to the reinforcement as
40mm

d = 500-40-16/2
= 452mm
Max. Shear resistance
VRD,max = 0.5ud[0.6(1-fck/250)](fck/1.5)
= 0.5*(4*400)*452*0.6*(1-30/250)*(30/1.5)*10^-3
= 3818.5kN
Hence, VRd,max > VEd = 1815kN

Punching Shear

Critical section is considered at 2d from the face of the column

Critical Perimeter = Column Perimeter + 4d


= 4*400 + 4*452
= 7280mm
Area with the perimeter = (400-4d)^2 -(4-)(2d)^2
= (400+4*452)^2 -(4-)(2*452)^2
= 4.17*10^6 mm
Punching Shear Force = 216*(2.9^2-4.17)
= 915.84kN
Shear Stress = VEd/(perimeter * d)
= 915.84*E3/ (7280* 452)
= 0.28
Shear stress is not that large so 500mm thickness can be used

Bending Reinforcements
Consider critical section (at column face)

MEd = 216*2.9*(2.9/2-0.4/2)*(2.9/2-0.4/2)/2
= 490kNm
K = M/[b*(d^2)*fck]
K = 490*E6/[1000*(452^2)*30]
K = 0.08

Kbal = 0.167 (balance codition is taken based on x = 0.45d)


Therefore
K<Kbal
Compression reinforcement is not required

z = d[0.5+(0.25-K/1.134)^0.5]
z = 452[0.5+(0.25-0.08/1.134)^0.5]
z = 417.5mm (Z/d = 0.92<0.95)

As = M/(0.87*fyk*z)
As = 490*E6/(0.87*500*417.5
= 2698mm2
Provide T25@175mm spacing (As Provided = 2804mm2)
OR you may increase the depth of the footing in order to reduce the reinforcement area.

Check for Punching Shear


As/(bd) = 2698/(1000*452)
= 0.006
= 0.6% < 2%
Therefore,
Shear stress = 0.4N/mm2

VRd,c = 0.4*7280*542
= 1316.2kN > 915.84kN
Hence, punching shear is ok.

Check for Maximum Shear


Consider 1.0d form face of the column

Design Shear Force = 216*2.9*0.798


= 499.9kN
As above
VRd,c @ 1.0d = 0.4*1000*452
= 180.8kN < 499.9kN
Hence,
Shear reinforcement is required.
Normally, Shear reinforcements are not provided for pad footings. Therefor, the thickness of the footing
may be increased and re-do the design as done above.

You might also like