Project Job Ref.

Section Sheet no./rev.

1
Calc. by Date Chk'd by Date App'd by Date
D 9/24/2017

FOUNDATION ANALYSIS & DESIGN (ACI318)

In accordance with ACI318-11 incorporating Errata as of August 8, 2014
Tedds calculation version 3.0.04

FOOTING ANALYSIS
Length of foundation; Lx = 9.5 ft; Width of foundation; Ly = 9.5 ft
2
Foundation area; A = 90.25 ft ; Depth of foundation; h = 27 in
Depth of soil over foundation; hsoil = 0 in; Density of concrete; conc = 150.0 lb/ft3

4.77 ksf 4.77 ksf

4.77 ksf 4.77 ksf

Column no.1 details

Length of column; lx1 = 16.00 in; Width of column; ly1 = 16.00 in
position in x-axis; x1 = 57.00 in; position in y-axis; y1 = 57.00 in
Soil properties
Gross allow. bearing press.; qallow_Gross = 5 ksf; Density of soil; soil = 110.0 lb/ft3
Angle of internal friction; b = 32.0 deg; Design base friction angle; bb = 32.0 deg
Coefficient of base friction; tan(bb) = 0.625
Design wall friction angle; b = 15.0 deg
Passive pressure coeff.; KP = 5.541
Foundation loads
Self weight; Fswt = 337.5 psf
Column no.1 loads
Dead load in z; FDz1 = 200.0 kips; Live load in z; FLz1 = 200.0 kips
Footing analysis for soil and stability
 Project Job Ref.

Section Sheet no./rev.

2
Calc. by Date Chk'd by Date App'd by Date
D 9/24/2017

Load combinations per ASCE 7-10

1.0D (0.511)
1.0D + 1.0L (0.954)

Combination 2 results: 1.0D + 1.0L

Forces on foundation
Force in z-axis; Fdz = 430.5 kips
Moments on foundation
Moment in x-axis, about x is 0; Mdx = 2044.7 kip_ft; Moment in y-axis, about y is 0; Mdy = 2044.7 kip_ft
Uplift verification
Vertical force; Fdz = 430.459 kips
PASS - Foundation is not subject to uplift
Bearing resistance
Eccentricity of base reaction
Eccentricity in x-axis; edx = 0 in; Eccentricity in y-axis; edy = 0 in
Pad base pressures
Min. base press.; qmin = 4.77 ksf; Max. base press.; qmax = 4.77 ksf
Allowable bearing capacity
Allowable bearing capacity; qallow = 5 ksf; qmax / qallow = 0.954
PASS - Allowable bearing capacity exceeds design base pressure

FOOTING DESIGN (ACI318)

In accordance with ACI318-11 incorporating Errata as of August 8, 2014
Material details
Compr. strength of concrete; fc = 3000 psi; Yield strength of reinforcement; fy = 60000 psi
Cover to reinforcement; cnom = 3 in; Concrete type; Normal weight
Concrete modification factor; = 1.00; Column type; Concrete

Analysis and design of concrete footing

Load combinations per ASCE 7-10
1.4D (0.435)
1.2D + 1.6L + 0.5Lr (0.871)

Combination 2 results: 1.2D + 1.6L + 0.5Lr

Forces on foundation
Ultimate force in z-axis; Fuz = 596.6 kips
Moments on foundation
Ultimate moment in x-axis, about x is 0; Mux = 2833.6 kip_ft; Ultimate moment in y-axis,
about y is 0; Muy = 2833.6 kip_ft
Eccentricity of base reaction
Eccentricity in x-axis; eux = 0 in; Eccentricity in y-axis; euy = 0 in
Pad base pressures
Min. ultimate base press.; qumin = 6.61 ksf; Max. ultimate base press.; qumax = 6.61 ksf
 Project Job Ref.

Section Sheet no./rev.

3
Calc. by Date Chk'd by Date App'd by Date
D 9/24/2017

Shear diagram, x axis (kips)

280
127.5

0
0
-127.4

-280

Moment diagram, x axis (kip_ft)

491.6

0 0

665

Moment design, x direction, positive moment

Ultimate bending moment; Mu.x.max = 491.591 kip_ft; Tension reinf. provided; 18 No.5 bot. bars (6.3 in c/c)
Area of tension reinf. provided; Asx.bot.prov = 5.58 in2; Min. area of reinforcement; As.min = 5.540 in2
PASS - Area of reinforcement provided exceeds minimum
Maximum spacing of reinf.; smax = 18 in
PASS - Maximum permissible reinforcement spacing exceeds actual spacing
Depth to tension reinf.; d = 23.687 in; Depth of compression block; a = 1.152 in
Neutral axis factor; 1 = 0.85; Depth to neutral axis; c = 1.355 in
Strain in tensile reinf.; t = 0.04945
PASS - Tensile strain exceeds minimum required, 0.004
Nominal moment capacity; Mn = 644.815 kip_ft; Flexural strength red. factor; f = 0.900
Design moment capacity; Mn = 580.333 kip_ft; Mu.x.max / Mn = 0.847
PASS - Design moment capacity exceeds ultimate moment load
One-way shear design, x direction
Ultimate shear force; Vu.x = 127.451 kips; Depth to reinforcement; dv = 23.687 in
Shear strength red. factor; v = 0.75; Nominal shear capacity; Vn = 295.811 kips
Design shear capacity; Vn = 221.858 kips; Vu.x / Vn = 0.574
PASS - Design shear capacity exceeds ultimate shear load
Two-way shear design at column 1
Depth to reinforcement; dv2 = 23.375 in; Shear perimeter length; lxp = 39.375 in
Shear perimeter width; lyp = 39.375 in; Shear perimeter; bo = 157.500 in
Shear area; Ap = 1550.391 in2; Surcharge loaded area; Asur = 1294.391 in2
Ult. bearing press.; qup.avg = 6.610 ksf; Ultimate shear load; Fup = 493.193 kips
Ult. shear stress, vertical load; vug = 133.963 psi; Column geometry factor; = 1.00
Column location factor; s =40; Concrete shear strength; vcp = 219.089 psi
Shear strength red. factor; v = 0.75; Nominal shear stress capacity; vn = 219.089 psi
Design shear stress capacity; vn = 164.317 psi; vug / vn = 0.815
 Project Job Ref.

Section Sheet no./rev.

4
Calc. by Date Chk'd by Date App'd by Date
D 9/24/2017

PASS - Design shear stress capacity exceeds ultimate shear stress load
Shear diagram, y axis (kips)
280
127.5

0
0
-127.4

-280

Moment diagram, y axis (kip_ft)

491.6

0 0

665

Moment design, y direction, positive moment

Ultimate bending moment; Mu.y.max = 491.591 kip_ft; Tension reinf. provided; 18 No.5 bot. bars (6.3 in c/c)
2
Area of tension reinf. provided; Asy.bot.prov = 5.58 in ; Min. area of reinforcement; As.min = 5.540 in2
PASS - Area of reinforcement provided exceeds minimum
Maximum spacing of reinf.; smax = 18 in
PASS - Maximum permissible reinforcement spacing exceeds actual spacing
Depth to tension reinf.; d = 23.062 in; Depth of compression block; a = 1.152 in
Neutral axis factor; 1 = 0.85; Depth to neutral axis; c = 1.355 in
Strain in tensile reinf.; t = 0.04806
PASS - Tensile strain exceeds minimum required, 0.004
Nominal moment capacity; Mn = 627.377 kip_ft; Flexural strength red. factor; f = 0.900
Design moment capacity; Mn = 564.64 kip_ft; Mu.y.max / Mn = 0.871
PASS - Design moment capacity exceeds ultimate moment load
One-way shear design, y direction
Ultimate shear force; Vu.y = 127.451 kips; Depth to reinforcement; dv = 23.062 in
Shear strength red. factor; v = 0.75; Nominal shear capacity; Vn = 288.006 kips
Design shear capacity; Vn = 216.005 kips; Vu.y / Vn = 0.590
PASS - Design shear capacity exceeds ultimate shear load
Two-way shear design at column 1
Depth to reinforcement; dv2 = 23.375 in; Shear perimeter length; lxp = 39.375 in
Shear perimeter width; lyp = 39.375 in; Shear perimeter; bo = 157.500 in
2
Shear area; Ap = 1550.391 in ; Surcharge loaded area; Asur = 1294.391 in2
Ult. bearing press.; qup.avg = 6.610 ksf; Ultimate shear load; Fup = 493.193 kips
Ult. shear stress, vertical load; vug = 133.963 psi; Column geometry factor; = 1.00
Column location factor; s =40; Concrete shear strength; vcp = 219.089 psi
Shear strength red. factor; v = 0.75; Nominal shear stress capacity; vn = 219.089 psi
 Project Job Ref.

Section Sheet no./rev.

5
Calc. by Date Chk'd by Date App'd by Date
D 9/24/2017

Design shear stress capacity; vn = 164.317 psi; vug / vn = 0.815

PASS - Design shear stress capacity exceeds ultimate shear stress load

18 No.5 bottom bars (6.3 in c/c)

18 No.5 bottom bars (6.3 in c/c)