Motor Protection Principles

Craig Wester
GE Multilin
[email protected]
Motor History & Facts

2
Motor History & Facts
The first U.S. patent for a motor Today in North America, more
was issued to Thomas Davenport in than 1 billion motors are in
1837. service.

Motors consume 25% of

electricity in North America.

Electricity consumption by motors

In 1888, Nikola Tesla patented the in manufacturing sector is 70%.
first AC poly-phase motor. In oil, gas and mining industries
around 90%.

Three phase squirrel-cage

induction motors account for over
90% of the installed motor
capacity.

3
Various Industry Motor Applications

Fans, Blowers
Pumps, Compressors
Grinders, Chippers
Conveyors, Shredders
Crushers, Mixers
Cranes, Extruders
Refiners, Chillers
 Motor Failure Rates and Cost
IEEE STUDY EPRI STUDY AVERAGE
Motor failure rate is FAILURE % FAILED COMPONENT % %

conservatively estimated as CONTRIBUTOR

Persistent Overload 4.20% Stator Ground Insulation 23.00
Electrical
26.40% 4.00
3-5% per year Normal Deterioration Turn Insulation
Bracing 3.00
Related Failures

In Mining, Pulp and Paper Core 1.00

industry, motor failure rate Cage 5.00 33%

Electrical Related Total 30.60% Electrical Related Total 36.00%
can be as high as 12%. High Vibration 15.50% Sleeve Bearings 16.00
Mechanical
Poor Lubrication 15.20% Antifriction Bearings 8.00
Related Failures
5.00
Motor failures divided in 3 Trust Bearings
Rotor Shaft 2.00
groups: Rotor Core 1.00
31%
Mechanical Related Mechanical Related
Electrical (33%) Total
30.70%
Total
32.00%

Mechanical (31%) High Ambient Temp. 3 Bearing Seals 6.00

Environmental,
Abnormal Moisture 5.8 Oil Leakege 3.00
Environmental, Abnormal Voltage 1.5 Frame 1.00
Maintanence &
Other Reasons
Maintenance, & Other (36%) Abnormal Frequency 0.6 Wedges 1.00 Related Failures
Abrasive Chemicals 4.2
Poor Ventilation Cooling 3.9
Other Reasons 19.7 Other Components 21.00

Environmental Related Maintanence Related &

36%
38.70% 32.00%
& Other Reasons: Other Parts: Total
Total
 Motor Failure
t Rates and Cost
Produc
M r tion
o i
t b Harsh
o u Conformal
r t Coating Can
o Reduce
f r E
a s n
i : v
l i
u Repair r
r or o
e Repla n
cemen m
c t e
o n
s Remov t
al and a
t
Install l
c ation
F
o Loss
a
n of
Motor
i
l
Failure Rates and Cost
u
r
e
s
Thermal Stress Causes Motor Failure
Most of the motor failure contributors and failed motor components are
related to motor overheating.

Thermal stress potentially can cause the failure of all the major motor parts:
Stator, Rotor, Bearings, Shaft and Frame.
Risks for an Overheated
Motor
Stator Windings Insulation Degradation (for stator limited motors)
Insulation lifetime decreases by half if motor operating temperature
exceeds thermal limit by 10C for any period of time
110
Risks for an Overheated 100

For F class

PERCENTAGE OF LIFE (%)

90

Motor 80

70
A B F H insulation, stator
temperature of
165C causes motor
60 lifetime to decrease
to 50%
50
A-CLASS (105 C)
40
B-CLASS (130C)
30
F-CLASS (155 C)
20
H-CLASS (180 C)
10

0
0 50 100 150 200 250 300
TEMPERATURE (C)

Rotor Conductors Deforming or Melting (for rotor limited - thermal limit is

defined by motor stall time)
Motor Electrical Protection
Thermal Overload
Process Caused (Excessive load)
High Ambient Conditions (Hot, Blocked Ventilation)
Power Supply Issues (Voltage/Current Unbalance, Harmonics)

Phase Fault
Ground Fault
Abnormal Operating Conditions
Over & Under Voltage
Underfrequency
Voltage and Current Unbalance
Load Loss
Jamming
Jogging
Overload Protection - Thermal Model
A motor can run overloaded without a fault in motor or supply
A primary motor protective element of the motor protection relay is the
thermal overload element and this is accomplished through motor
thermal image modeling. This model must account for thermal process
in the motor while motor is starting, running at normal load, running
overloaded and stopped. Algorithm of the thermal model integrates
both stator and rotor heating into a single model.

Main Factors and Elements Comprising

the Thermal Model are:
Overload Pickup Level
Overload Curve
Running & Stopped Cooling Time Constants
Hot/Cold Stall Time Ratio
RTD & Unbalance Biasing
Motor State Machine
Thermal Model - Motor States
Motor Stopped:
Current < 0 threshold & contactor/breaker is open.

Motor Starting:
Previous state is Stopped & Current > 0 threshold. Motor current
must increase to the level higher than overload pickup within
seconds.

Motor Running:
Previous state is Starting or Overloading & Current drops below
overload pickup level.

Motor Overloading:
Previous state is Running & Current raises above overload pickup
level. Thermal Capacity Used (TCU) begins to accumulate during
overload.
Motor Thermal Limit Curves
Thermal Limit of the model is dictated by overload curve
constructed in the motor protection device in reference to thermal
damage curves normally supplied by motor manufacturer.

Motor protection device is equipped with set of standard

curves and capable to construct customized curves for any
motor application.

Thermal Limit Curves:

A
A. Cold Running Overload
C
B. Hot Running Overload
B
C. Cold Locked Rotor Curve
D D. Hot Locked Rotor Curve
E. Acceleration curve @ 80% rated
E F voltage
F. Acceleration curve @100%
voltage
Thermal Overload Pickup
Set to the maximum allowed by the
service factor of the motor.
Set slightly above the motor service
factor by 8-10% to account for
measuring errors

If RTD Biasing of Thermal Model is

used, thermal overload setting can
be set higher
Thermal
Note: motor Overload Pickup
feeder cables
SF Thermal
are normally
Overload
sized at 1.25
Pickup
times motors
full load 1.0
current rating, 1.1
which would 1.15
limit the motor 1.25
overload
pickup setting
to a maximum
of 125%.
Thermal Model Thermal Capacity
Used
Thermal Capacity Used (TCU) is a criterion selected in thermal
model to evaluate thermal condition of the motor.

TCU is defined as percentage of motor thermal limit utilized

during motor operation.

A running motor will have some level of thermal capacity used due
to Motor Losses.

Thermal Overload Trip when Thermal Capacity Used equals 100%

Overload Curve Selection for Thermal Model

Overload Curve
Set the overload curve below cold thermal limit and above hot thermal limit
If only hot curve is provided by mfgr, then must set at or below hot thermal limit
Thermal ModelHot/Cold Stall Time Ratio (HCR)
Typically motor manufacturer provides the values of the locked rotor
thermal limits for 2 motor conditions:
COLD : motor @ ambient temperature
HOT : motor @ rated temperature for specific class and service factor.
NEMA standard temperature rises for motors up to 1500HP and Service
Factors 1 and 1.15 respectively.

AMBIENT CLASS A CLASS B CLASS F CLASS H

When motor is running below overload pickup, the TCU will rise or fall to value
based on average current and HCR. HCR is used to calculate level of TCU by
relay, at which motor will settle for current below overload pickup.
Hot/Cold Safe Stall Ratio
Hot/Cold Safe Stall Ratio HCR =
LRTHOT
LRTCOLD

Hot/Cold Ratio =
30/35
=> 0.86

Overload Curve Method

If the thermal limits curves are being used to

determine the HOT/COLD ratio proceed as follows:

From the thermal limits curves run a line

LRTcold = 8sec perpendicular to the current axis that intersects the
hot and cold curves at the stall point or LRA
The Hot/cold ratio can now be calculated as follows:
LRThot = 6sec = 6s/8s = 0.75
If hot and cold times are not provided and only one
curve is given verify with the manufacturer that it is
LRC = 5.4FLA
the hot curve ( which is the worst case), then the
Hot/ Cold ratio should be set to 1.0
Overload Curve Selection
If the motor starting current
begins to infringe on the
thermal damage curves or if
the motor is called upon to
drive a high inertia load such
that the acceleration time
exceeds the safe stall time,
custom or voltage
dependent overload curve
may be required.
Overload Curve Selection
A custom overload curve will
allow the user to tailor the
relays thermal damage
curve to the motor such that
a successful start can occur
without compromising
protection while at the same
time utilizing the motor to its
full potential during the
running condition.
Thermal Model Behavior - Long Starts
Issue Duration of a high inertia load start is longer than the allowed
motor safe stall time.
For these starts, thermal model must account for the current change during
acceleration and also use the acceleration thermal limits for TCU calculations.
Motor thermal limit is growing along with motor rotation speed during
acceleration.
Starting current is proportional to system voltage during motor acceleration,
thus voltage could be a good indication of the current level corresponding to the
locked rotor conditions.
Voltage dependant dynamic thermal limit curve is employed to enhance the
thermal model algorithm.
Motor relay will shift acceleration
thermal limit curve linearly
and constantly based on
measured line voltage during
a motor start.

18
Thermal Model - Current Unbalance Bias
Negative sequence currents (or unbalanced phase currents) will
cause additional rotor heating that will be accounted for in Thermal
Model.

19
Thermal Model - Current Unbalance
Main causes Bias
of current unbalance
Blown fuses
Loose connections
Stator turn-to-turn faults
System voltage distortion and unbalance
Faults
Positive Sequence

Negative Sequence

20
 Equivalent heating motor current is employed to bias thermal
model in response to current unbalance.
 2 2
IEQ = IM (1 + K I1 ) )
(I2

Im - real motor current; K - unbalance bias factor; I1 & I2 - positive

and negative sequence components of motor current.
K factor reflects the degree of extra heating caused by the negative
sequence component of the motor current.
IEEE guidelines for typical and conservative estimates of K.

K = 175 ILRC
2
TYPICAL

K = 230 I2 CONSERVATIVE
LRC
Thermal Model RTD Bias
Accelerate thermal trip for
hot stator windings
RTD bias model determines the
Thermal Capacity Used based on the
temperature of the Stator and is
separate from the overload model for
calculating Thermal Capacity Used.
Motor relay will use the calculated
thermal capacity unless the RTD
thermal capacity is higher.
This function will not trip the motor at
the max point temp unless the average
current is greater than the overload
pickup setting
RTD biasing is a back up protection
element which accounts for such things
as loss of cooling or unusually high
ambient temperature.
Thermal Model RTD Bias 21
Thermal Model - Motor
Cooling
Motor cooling is characterized by separate cooling time constants
(CTC) for running and stopped motor states. Typical ratio of the
stopped to running CTC is 2/1
It takes the motor typically 5 time constants to cool.
Thermal
Thermal
Model
Model - Motor
Thermal Model
Cooling100% load -
Cooling
Cooling
Motor
Running

Tripped

22
Overvoltage Protection
The overall result of an overvoltage condition is a decrease
in load current and poor power factor.
Although old motors had robust design, new motors are
designed close to saturation point for better utilization of
core materials and increasing the V/Hz ratio cause
saturation of air gap flux leading to motor heating.
The overvoltage element should be set to 110% of the
motors nameplate unless otherwise started in the data
sheets.
Overvoltage Protection 23
Undervoltage Protection
The overall result of an undervoltage condition is an increase in current
and motor heating and a reduction in overall motor performance.

The undervoltage protection element can be thought of as backup

protection for the thermal overload element. In some cases, if an
undervoltage condition exists it may be desirable to trip the motor faster
than thermal overload element.

The undervoltage trip should be set to 80-90% of nameplate unless

otherwise stated on the motor data sheets.

Motors that are connected to the same source/bus may experience a

temporary undervoltage, when one of motors starts. To override this
temporary voltage sags, a time delay setpoint should be set greater than
the motor starting time.
Undervoltage Protection 24
Unbalance Protection
Indication of unbalance negative sequence current / voltage
Unbalance causes motor stress and temperature rise
Current unbalance in a motor is result of unequal line voltages
Unbalanced supply, blown fuse, single-phasing
Unbalance Protection
Current unbalance can also be present due to:
Loose or bad connections
Incorrect phase rotation connection
Stator turn-to-turn faults
Motor Relay

For a typical three-phase induction motor:

1% voltage unbalance (V2) relates to 6% current unbalance (I2)
For small and medium sized motors, only current transformers (CTs) are available
and no voltage transformers (VTs). Measure current unbalance and protect motor.
The heating effect caused by current unbalance will be protected by enabling the
unbalance input to the thermal model
For example, a setting of 10-15% x FLA for the current unbalance alarm with a
delay of 5-10 seconds and a trip level setting of 20-25% x FLA for the current
unbalance trip with a delay of 2-5 seconds would be appropriate.
25
Ground Fault Protection

A ground fault is a fault that creates a path

for current to flow from one of the phases
directly to the neutral through the earth
bypassing the load

Ground faults in a motor occur:

When its phase conductors insulation is
damaged for example due to voltage stress,
moisture or internal fault occurs between the
conductor and ground

To limit the level of the ground fault current

connect an impedance between the
supplies neutral and ground. This
impedance can be in the form of a resistor
or grounding transformer sized to ensure
maximum ground fault current is limited.
Ground Fault Protection 26
Ground Fault Protection
Zero Sequence CT Connection
Best method
Most sensitive & inherent noise immunity

All phase conductors are passed through the window of the same CT referred
to as the zero sequence CT
Under normal circumstances, the three phase currents will sum to zero
resulting in an output of zero from the Zero Sequence CTs secondary.
If one of the motors phases were to shorted to ground, the sum of the phase
currents would no longer equal zero causing a current to flow in the secondary
of the zero sequence. This current would be detected by the motor relay as a
ground fault.
Ground Fault Protection 27
Ground Fault Protection
Residual Ground Fault Connection
Less sensitive
Drawbacks due to asymmetrical starting
current and un-matched CTs

For large cables that cannot be fit through the zero sequence CTs window, the
residual ground fault configuration can be used.
This configuration is inherently less sensitive than that of the zero sequence
configuration owing to the fact that the CTs are not perfectly matched.
During motor starting, the motors phase currents typically rise to magnitudes
excess of 6 times motors full load current and are asymmetrical.
The combination of non perfectly matched CTs and relative large phase current
magnitudes produce a false residual current. This current will be
misinterpreted by the motor relay as a ground fault unless the ground fault
elements pickup is set high enough to disregard this error during starting
Ground Fault Protection 28
Differential Protection
Differential protection may be considered the first line of protection
for internal phase-to-phase or phase-to-ground faults. In the event
of such faults, the quick response of the differential element may
limit the damage that may have otherwise occurred to the motor.

Core balance method:

Two sets of CTs, one at the beginning of
the motor feeder, and the other at the
neutral point
Alternatively, one set of three core-balance
CTs can also be used
The differential element subtracts the
current coming out of each phase from the
current going into each phase and
compares the result or difference with the
differential pickup level.
Differential Protection 29
Differential Protection

Summation method with six CTs:

If six CTs are used in a summing
configuration, during motor starting, the
values from the two CTs on each phase
may not be equal as the CTs are not
perfectly identical and asymmetrical
currents may cause the CTs on each phase
to have different outputs.
To prevent nuisance tripping in this
configuration, the differential level may
have to be set less sensitive, or the
differential time delay may have to be
extended to ride through the problem
period during motor starting.
The running differential delay can then be
fine tuned to an application such that it
responds very fast and is sensitive to low
differential current levels.
Differential Protection 30
Differential Protection

Biased differential protection - six CTs:

Biased differential protection method allows
for different ratios for system/line and the
neutral CTs.
This method has a dual slope characteristic.
Main purpose of the percent-slope
characteristic is to prevent a mis-operation
caused by unbalances between CTs during
external faults. CT unbalances arise as a
result of CT accuracy errors or CT saturation.
Characteristic allows for very sensitive
settings when the fault current is low and less
sensitive settings when the fault current is
high and CT performance may produce
incorrect operating signals.
Short Circuit Protection
The short circuit element provides protection
for excessively high overcurrent faults
Phase-to-phase and phase-to-ground faults
are common types of short circuits
When a motor starts, the starting current
(which is typically 6 times the Full Load
Current) has asymmetrical components .
These asymmetrical currents may cause one
phase to see as much as 1.7 times the RMS
starting current.
To avoid nuisance tripping during starting,
set the the short circuit protection pick up to
a value at least 1.7 times the maximum
expected symmetrical starting current of
motor.
The breaker or contactor must have an
interrupting capacity equal to or greater then
the maximum available fault current or let an
upstream protective device interrupt fault
current. 32
Stator RTD Protection
A simple method to determine the heating
within the motor is to monitor the stator with
RTDs.
Stator RTD trip level should be set at or below
the maximum temperature rating of the
insulation.
For example, a motor with class F insulation
that has a temperature rating of 155C could
have the Stator RTD Trip level be set between
140C to 145C, with 145 C being the
maximum (155C - 10C hot spot)
The stator RTD alarm level could be set to a
level to provide a warning that the motor
temperature is rising

33
Additional Protection Methods

Start Inhibit
This function will limit starts when the motor is already hot.

Starts/Hour

Time Between Starts (Jogging)

Bearing RTD Protection

Acceleration Trip
Set higher than the maximum starting time to avoid nuisance
tripping when the voltage is lower or for varying loads during
acceleration.
34
Conclusions
Induction & synchronous motors are valuable assets to
todays industrial facilities.
The temperature rise of motor dictates its life
When applied, thermal protection can prevent loss of motor
life
Additional protection elements such as overvoltage,
undervoltage, unbalance, ground fault, differential, short
circuit and stator RTD supplement the thermal model
protection and provide complete motor protection.
Harsh conformal coating of motor protection relays should
be considered to avoid the environmental effects of harsh
gaseous sulphides (H2S, etc.)

35