Scribd
Upload
160 views

Audio Oscillator Circuit

The document describes an audio oscillator circuit using the ICL8038 waveform generator IC. The ICL8038 can produce sine, square, and triangular waveforms with low distortion from 0.001Hz to 300KHz by using an external timing capacitor and resistor. The circuit diagram shows a variable audio frequency oscillator using the ICL8038 that generates frequencies from 20Hz to 20KHz. Potentiometers can be used to adjust the frequency, distortion, duty cycle, and variations in duty cycle.

Uploaded by

wira
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
160 views

Audio Oscillator Circuit

The document describes an audio oscillator circuit using the ICL8038 waveform generator IC. The ICL8038 can produce sine, square, and triangular waveforms with low distortion from 0.001Hz to 300KHz by using an external timing capacitor and resistor. The circuit diagram shows a variable audio frequency oscillator using the ICL8038 that generates frequencies from 20Hz to 20KHz. Potentiometers can be used to adjust the frequency, distortion, duty cycle, and variations in duty cycle.

Uploaded by

wira
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Audio oscillator circuit

ICL 8038 waveform generator.

ICL8038 is a monolithic waveform generator IC that can produce sine, square and triangular waveforms
with very little distortion. The frequency can be programmed from 0.001Hz to 300 KHz using external
timing capacitor and resistor. Frequency modulation and sweeping can be attained by using an external
voltage. Other features of the ICL8038 are high linearity, high level outputs, simultaneous sine, square,
triangle wave outputs, low external parts count, high temperature stability etc.

The working of ICL8038 is as follows. The external timing capacitor (C2 in the circuit diagram) is charged
and discharged using two internal current sources. The first current source is on all the time and second
current is switched ON and OFF using a flip-flop. Suppose the second current source is OFF and the first
current source is ON, then the capacitor C2 will be charged with a continuous current (i) and the voltage
across C2 increases linearly with time. When the voltage reaches 2/3 supply voltage, controlling flip flop
is triggered and the first current source is activated. This current source carries double the current (2i)
making the capacitor C2 is discharged with a current i and the voltage across it drops linearly with time.
When this voltage reaches 1/3 supply voltage, the flip flop is resetted to the initial condition and the
cycle is repeated again.

Circuit diagram ICL8038 audio oscillator.


The circuit diagram given above shows a variable audio frequency oscillator using ICL8038. Such a
circuit is very useful while testing audio related projects. The frequency range of this circuit is 20Hz
to 20KHz. POT R6 can be used for adjusting the frequency while POT R9 can be used for adjusting
the distortion. POT R4 can be used for adjusting the duty cycle while POT R7 can be used for
nullifying the variations in duty cycle. C2 is the external timing capacitor and R5 is a pull up resistor.
Merupakan Potensiometer Digital yang dikontrol melalui SPI yang biasanya terdapat pada mikrokontroler.
Sangat dianjurkan menggunakan mikrokontroler Arduino untuk mengatur resistansi MCP42100.
pada MCP42100 terdapat 2 output sehingga dapat digunakan untuk 2 device yang berbeda dengan
menggunakan 1 ic MCP42100.

Spec :
Control Interface: Serial, SPI
End To End Resistance: 100kohm
MSL: -
No. of Pins: 14
No. of Pots: Dual
No. of Steps: 256
Operating Temperature Max: 85C
Operating Temperature Min: -40C
Potentiometer IC Case Style: DIP
Resistance Tolerance: -
Supply Voltage Max: 5.5V
Supply Voltage Min: 2.7V
Supply Voltage Range: 2.7V to 5.5V
Temperature Coefficient: 800ppm/C
Track Taper: Linear

You might also like