Scribd
Upload
162 views

IDG Setup Guide

This document provides instructions for setting up a virtual IBM Datapower Gateway v7.5. It outlines the minimum system requirements, which include 64-bit x86 architecture, virtualization technology enabled, 2.0GHz processor, 4GB RAM, and 150GB disk space. It then walks through the installation wizard steps to configure networking, services, host name, remote access via SSH and webGUI, user accounts, disk array, and license acceptance.

Uploaded by

Jonathan Campos
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
162 views

IDG Setup Guide

This document provides instructions for setting up a virtual IBM Datapower Gateway v7.5. It outlines the minimum system requirements, which include 64-bit x86 architecture, virtualization technology enabled, 2.0GHz processor, 4GB RAM, and 150GB disk space. It then walks through the installation wizard steps to configure networking, services, host name, remote access via SSH and webGUI, user accounts, disk array, and license acceptance.

Uploaded by

Jonathan Campos
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Set up a Virtual IBM Datapower Gateway v7.

Requisitos

La mquina debe tener una tecnologa de 64-bit x86.


Tener activado el virtualization technology (VT-x).
Velocidad mnima 2.0 GHz.
4 virtual CPUs
Se recomienda como mnimo 150 GB de espacio en disco.
4 a 8GB RAM.

Configuracin de Datapower Gateway v7.5

Encender el DataPower y loguearse con las siguientes credenciales


login: admin
password: admin
Enter Disaster Recovery mode [yes/no]: no
Enter Common Criteria Compatibility mode? [yes/no]: no
Please enter new password: provide-password
Do you want to run the Install Wizard? [y:n]: y

Paso 1 Do you want to configure network interfaces? [y]: y


Do you have this information? [y]: y
Do you want to configure the eth0 interface? [y]: y
Do you want to enable DHCP? [y]: n
Enter the IP address for interface in CIDR notation: 192.168.xxx.100/24
Note:
La IP configurada est a modo de ejemplo.
Enter the IP Address for default IPv4 gateway []: 192.168.xxx.100
Enter n for question to configure eth1, eth2 and eh3 interfaces.

Paso 2:
Do you want to configure network services? [y]: y
Do you want to configure DNS? [y]: n
Paso 3:
Do you want to define unique system identifier for the appliance? [y] :
Note: Ingresar un hostname para el DataPower

Paso 4:
Do you want to configure remote management access? [y]: y
Esta configuracin require la IP de la interfaz de gestin.
Do you have this information? [y]: y
Do you want to enable SSH? [y]: y
Enter the local IP address [0 for all] : 192.168.1.10
Nota: Ingresar la misma IP configurada anteriormente

Enter the port number [22]:


Nota: Enter para aceptar por default.
Do you want to enable WebGUI access [y]: y

Enter the local IP address [0 for all] : 192.168.1.10


Nota: Ingresar la misma IP configurada anteriormente

Enter the port number [9090]:


Nota: Enter para aceptar por default.

Paso 5: Do you want to configure a user account that can reset passwords [y]: y
Es opcional

Paso 6: Do you want to configure the hard disk array? [y]: y

Do you want to continue? [y]:


Enter name for the file system [ondisk]: dpdiskarray
Nota: Ingresar un nombre apropiado
Paso 7 Do you want to review the current configuration? [y]:
Do you want to save current configuration? [y]: y
Overwrite previously saved configuration? [y/n]:
And now everything should be set and you can get to web interface.

Paso 8 Ingresar a la consola Web y aceptar los certificados


http://ipAddress:9090/

Paso 9 Aceptar la licencia del DataPower

You might also like