Scribd
Upload
296 views

Foot Step Power Generation System Using Pic Microcontroller

This document describes a footstep power generation system that converts the kinetic energy of footsteps into electrical energy. It uses piezoelectric sensors to transduce force into voltage, which is then filtered and regulated to charge a lead acid battery. A PIC microcontroller monitors the battery voltage and displays it on an LCD. The stored energy can power devices directly or be inverted to AC. Potential applications include charging phones, powering lights at bus stops or in rural areas without a grid connection.

Uploaded by

Aprilian Sandi
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
296 views

Foot Step Power Generation System Using Pic Microcontroller

This document describes a footstep power generation system that converts the kinetic energy of footsteps into electrical energy. It uses piezoelectric sensors to transduce force into voltage, which is then filtered and regulated to charge a lead acid battery. A PIC microcontroller monitors the battery voltage and displays it on an LCD. The stored energy can power devices directly or be inverted to AC. Potential applications include charging phones, powering lights at bus stops or in rural areas without a grid connection.

Uploaded by

Aprilian Sandi
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Foot step power generation system using pic microcontroller

1 Foot step power generation system


2 Foot step power generation system working
3 Foot step power generation system block diagram
4 PIC Microcontroller based Foot step power generation system
5 Components of microcontrollers based foot step power generation system
o 5.1 PIEZO ELECTRIC SENSOR
o 5.2 Filtering
o 5.3 UNIDIRECTIONAL CURRENT CONTROLLER
o 5.4 Lead acid battery
o 5.5 Voltage divider
o 5.6 PIC16F877A microcontroller
o 5.7 LCD display
6 Foot step power generation system code:
7 Click here to purchase code and circuit diagram
8 Applications

Foot step power generation system

In this foot step power generation project is designed to convert foot step, walking and
running energy into electrical energy. It is used to generate electricity from by walking or
running on foot step. The demand of electrical energy is increasing day by day. But power
generation conventional resources are now not enough for total demand of electrical energy.
Therefore many researchers and engineers are working on non conventional ways of
electrical power generation. Foot step power generation system is also a non conventional
electrical energy production system. It converts mechanical energy of foot steps into
electrical energy by using transducers. This power generation system can become very
popular among populated countries like Pakistan, china, India. It can be implemented on
roads, bus stations and many public places. Although this system is little bit expensive, but it
can make a huge difference in electrical power generation of country.

Foot step power generation system basically converts force energy of foot into electrical
energy by using piezoelectric sensor. Piezoelectric sensor is transducer which converts force
energy into electrical energy. I will discuss it in more detail in later part of this article.

Foot step power generation system working

Working of footstep power generation system consists of following main points:

Piezoelectric sensor interfaced with microcontroller and used as a transducer to


convert force energy into electrical energy
It is consists of large number of Piezoelectric sensors connected in series. Kinetic
energy of series connected transducers is converted into electrical energy.
Voltages generated by piezoelectric sensors are feed to circuit elements to get proper
output.
Output energy is stored in batteries.
Foot step power generation system block diagram

Its basic block diagram is shown below.

foot step power generation system using microcontroller

With application of force on piezoelectric transducer, its converts force into electrical energy.
AC ripple neutralizer controls the fluctuation in generated voltages and unidirectional current
controller controls the battery charging current with the help of pic16f877A pic
microcontroller. The voltage generated by series of sensors is stored in Lead Acid batteries.
This voltage can be used to drive either DC or AC loads. For AC loads, pure sine wave
inverter circuit is used. Inverter converts dc voltages stored in lead acid batteries in 220 volt
AC. AC voltage can be used to drive AC loads. User can use any type of inverter according
to his/her requirement like pure sine wave inverter, square wave inverter and modified sine
wave inverter. Rating of battery charger also depends on amount of power generation from
foot step.PIC16F877A microcontroller displays the amount of battery charging.

PIC Microcontroller based Foot step power generation system

Circuit diagram of microcontroller based foot step power generation system is shown below.
microcontroller based foot step power generation system

Components of microcontrollers based foot step power generation system

PIEZO ELECTRIC SENSOR

It is a sensor which converts force applied on sensor into voltage with the help of mechanical
vibrations. It basically converts kinetic energy into electrical energy. Array of sensors should
be connected in series to generate reasonable amount of electrical power. For example 10
piezoelectric sensors are connected in series; they will generate 9 volt and 100mA current.
Two types of such sensors are available in market lead zirconate titanate (PZT) and PVDF.
The output voltages of these sensors are controlled by filters.

Filtering

Capacitor is used as filter to remove AC components from sensors output voltages. A


capacitor stores minutes voltages with charging and discharging phenomenon. Capacitor acts
like a short circuit for AC voltages and open circuit for DC voltages. Output of filter is fed to
unidirectional current controller.

UNIDIRECTIONAL CURRENT CONTROLLER


Diodes and triacs are used as unidirectional current controllers. Diode and triac based charge
controller can be used to charge lead acid battery. In this project, triac based battery charger
is used. Triac firing angle control circuit is used to control flow of charge into battery. It
will make the flow of current in one direction only by conducting in one direction only. It is
used to protect back current to array of sensors. After that voltage is fed to lead acid battery
and voltage divider which is connected with PIC16F877A microcontroller.

Lead acid battery

Lead acid battery is used to store electrical energy. It is consists of electrochemical cells. In
foot step power generation system lead acid battery is used to store electrical energy of
sensors.

Voltage divider

Voltage divider lowers the voltage to the level of microcontroller. We cant fed 12 volt
directly to microcontroller. Voltage divider is used to divide the voltage. After that pic
microcontroller reads the analog voltage and displays on the LCD. If you dont know how to
measure dc voltage using pic microcontroller, dc voltmeter using pic microcontroller
project can help you to get its good understanding.

PIC16F877A microcontroller

PIC16F877A microcontroller is main part of foot step power generation system. It is used to
display battery voltage on LCD. It is also used to measure battery voltage with the help of
analog to digital converter of pic microcontroller. 10MHz crystal is used in this project.

LCD display

16 * 2 LCD is interfaced with microcontroller. LCD interfacing with pic microcontroller is


very simple task. It is used to display status of sensors and battery voltages. Ouput results are
shown below :

results of foot step power generation system

Foot step power generation system code:

Flow chart to write programming is given below:


code of Foot step power generation system

Click here to purchase code and circuit diagram

Applications

Foot step power generation system have many applications, but some of them are given
below:

Mobile charging
street lighting
bus station lighting
emergeny power failure stations
Rural areas etc

You might also like