Scribd
Upload
93 views4 pages

1 Level:: 2.1 Material Properties

This document provides information on the design of a reinforced concrete column. It includes details on the material properties, geometry, loads, calculation options, analysis results, and reinforcement details. The column is a 30x30 cm rectangular section with a height of 3 meters. The analysis shows it is a short column with a safety factor of 1.18. Reinforcement consists of 6 bars of 14mm diameter rebar and 13 stirrups and pins of 8mm diameter rebar.

Uploaded by

kkklllyyy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
93 views4 pages

1 Level:: 2.1 Material Properties

This document provides information on the design of a reinforced concrete column. It includes details on the material properties, geometry, loads, calculation options, analysis results, and reinforcement details. The column is a 30x30 cm rectangular section with a height of 3 meters. The analysis shows it is a short column with a safety factor of 1.18. Reinforcement consists of 6 bars of 14mm diameter rebar and 13 stirrups and pins of 8mm diameter rebar.

Uploaded by

kkklllyyy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as RTF, PDF, TXT or read online on Scribd
You are on page 1/ 4

1 Level:

0 Name : Standard Level


1 Reference level : ---
2 Concrete creep coefficient : jp = 2,91
3 cement class :N
4 Environment class : XC1
5 Structure class : S2

2 Column: Column1 Number: 1


2.1 Material properties:

6 Concrete : C25/30 fck = 25,00


(MPa)
Unit weight : 2501,36 (kG/m3)
Aggregate size : 16,0 (mm)
7 Longitudinal reinforcement: : B500B fyk = 500,00
(MPa)
Ductility class :B
8 Transversal reinforcement: : B500C fyk = 500,00
(MPa)

2.2 Geometry:
2.2.1 Rectangular 30,0 x 30,0 (cm)
2.2.2 Height: L = 3,00 (m)
2.2.3 Slab thickness = 0,16 (m)
2.2.4 Beam height = 0,36 (m)
2.2.5 Cover = 3,5 (cm)

2.3 Calculation options:

9 Calculations according to : EN 1992-1-1:2004 AC:2008


10 Seismic dispositions : No requirements
11 Precast column : no
12 Pre-design : no
13 Slenderness taken into account : yes
14 Compression : with bending
15 Ties : to slab
16 More than 50 % loads applied: after 90 day
17 Fire resistance class : No requirements

2.4 Loads:

Case Nature Group gf N My(s) My(i) Mz(s) Mz(i)


(kN) (kN*m) (kN*m) (kN*m) (kN*m)
DL1 dead load 1 1,35 -0,11 0,00 0,00 0,08 -0,08
DL2 dead load 1 1,35 0,21 0,00 0,00 -0,15 0,15
DL3 dead load 1 1,35 -0,99 0,00 0,00 0,71 -0,71
DL4 dead load 1 1,35 -1,61 0,00 0,00 1,15 -1,15
DL5 dead load 1 1,35 13,71 0,00 0,00 -3,16 3,16
DL6 dead load 1 1,35 69,84 0,00 0,00 -16,11 16,11
DL7 dead load 1 1,35 -8,20 0,00 0,00 5,86 -5,86
DL8 dead load 1 1,35 -5,06 0,00 0,00 3,61 -3,61
DL9 dead load 1 1,35 1,17 0,00 0,00 -0,84 0,84
DL10 dead load 1 1,35 -0,43 0,00 0,00 0,31 -0,31
LL1 live load 1 1,50 33,06 0,00 0,00 -7,63 7,63
LL2 live load 1 1,50 0,66 0,00 0,00 -0,47 0,47
LL3 live load 1 1,50 -0,18 0,00 0,00 0,13 -0,13
SNOW1 snow 1 1,50 -1,03 0,00 0,00 0,73 -0,73
SNOW2 snow 1 1,50 -1,17 0,00 0,00 0,84 -0,84
WIND1 wind 1 1,50 -0,58 0,00 0,00 0,41 -4,50
WIND2 wind 1 1,50 -1,16 0,00 0,00 0,83 20,64
DL11 dead load 1 1,35 -0,71 0,00 0,00 0,50 -0,50
LL4 live load 1 1,50 -0,36 0,00 0,00 0,26 -0,26
gf - load factor

2.5 Calculation results:


The cover deviation is less than recommended by the code. Smaller deviations
are allowed in structures where the quality assurance system is used. (Story
parameters)

Safety factors Rd/Ed = 1,18 > 1.0

2.5.1 ULS Analysis

Design combination:
1.35DL1+1.35DL2+1.35DL3+1.35DL4+1.35DL5+1.35DL6+1.35DL7+1.35DL8+1.35
DL9+1.35DL10+1.35DL11+1.05LL1+1.05LL2+1.50WIND2 (B)
Internal forces:
Nsd = 125,22 (kN) Msdy = 0,00 (kN*m) Msdz = 50,32 (kN*m)
Design forces:
Lower node
N = 125,22 (kN) N*etotz = 2,50 (kN*m) N*etoty= 51,26 (kN*m)

Eccentricity: ez (My/N) ey (Mz/N)


Static eEd: 0,0 (cm) 40,2 (cm)
Imperfection ei: 0,0 (cm) 0,8 (cm)
Initial e0: 0,0 (cm) 40,9 (cm)
Minimal emin: 2,0 (cm) 2,0 (cm)
Total etot: 2,0 (cm) 40,9 (cm)

2.5.1.1. Detailed analysis-Direction Y:

2.5.1.1.1 Slenderness analysis


Non-sway structure

L (m) Lo (m) l llim


3,00 3,00 34,64 42,13 Short column

2.5.1.1.2 Buckling analysis


M2 = 0,00 (kN*m) M1 = 0,00 (kN*m)
Case: Cross-section at the column end (Lower node), Slenderness not taken into account
M0 = 0,00 (kN*m)
ea = 0,0 (cm)
Ma = N*ea = 0,00 (kN*m)
MEdmin = 2,50 (kN*m)
M0Ed = max(MEdmin,M0 + Ma) = 2,50 (kN*m)

2.5.1.2. Detailed analysis-Direction Z:

2.5.1.2.1 Slenderness analysis


Non-sway structure

L (m) Lo (m) l llim


3,00 3,00 34,64 124,00 Short column

2.5.1.2.2 Buckling analysis


M2 = 50,32 (kN*m) M1 = -18,12 (kN*m)
Case: Cross-section at the column end (Lower node), Slenderness not taken into account
M0 = 50,32 (kN*m)
ea = q1*lo/2 = 0,8 (cm)
q1 = qo * ah * am = 0,01
qo = 0,01
ah = 1,00
am = (0,5(1+1/m))^0.5 = 1,00
m = 1,00
Ma = N*ea = 0,94 (kN*m)
MEdmin = 2,50 (kN*m)
M0Ed = max(MEdmin,M0 + Ma) = 51,26 (kN*m)

2.5.2 Reinforcement:

Real (provided) area Asr = 9,24 (cm2)


Ratio: r = 1,03 %

2.6 Reinforcement:
Main bars (B500B):
18 6 f14 l = 2,97 (m)

Transversal reinforcement: (B500C):


stirrups: 13 f8 l = 1,05 (m)
13 f8 l = 0,40 (m)

pins 13 f8 l = 1,05 (m)


13 f8 l = 0,40 (m)

3 Material survey:
19 Concrete volume = 0,24 (m3)
20 Formwork = 3,17 (m2)

21 Steel B500B
22 Total weight = 21,51 (kG)
23 Density = 90,51 (kG/m3)
24 Average diameter = 14,0 (mm)
25 Reinforcement survey:
Diameter Length Weight Number Total weight
(m) (kG) (No.) (kG)
14 2,97 3,58 6 21,51

26 Steel B500C
27 Total weight = 7,44 (kG)
28 Density = 31,31 (kG/m3)
29 Average diameter = 8,0 (mm)
30 Reinforcement survey:

Diameter Length Weight Number Total weight


(m) (kG) (No.) (kG)
8 0,40 0,16 13 2,08
8 1,05 0,41 13 5,36

You might also like