Scribd
Upload
50 views

Exp 12

This C program interfaces an LM35 temperature sensor with an LPC2148 microcontroller to read temperature data and display it on a PC through a serial port. The program initializes interrupts on pins connected to switches to trigger interrupt service routines. It also initializes the serial port and includes delay functions. The main function initializes interrupts, prints messages, and loops continuously printing the interrupt counts to demonstrate the interrupt functionality.

Uploaded by

Ashish Jog
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
50 views

Exp 12

This C program interfaces an LM35 temperature sensor with an LPC2148 microcontroller to read temperature data and display it on a PC through a serial port. The program initializes interrupts on pins connected to switches to trigger interrupt service routines. It also initializes the serial port and includes delay functions. The main function initializes interrupts, prints messages, and loops continuously printing the interrupt counts to demonstrate the interrupt functionality.

Uploaded by

Ashish Jog
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 2

Source Code

The Interfacing LM35 with LPC2148 program is very simple and straight forward, that reading
temperature from temperature sensor LM35 and it display into PC through serial port. The C
programs are written in Keil software. Some delay is occurring when a single data is sent to
PC.
#include
#include
int volatile EINT1 = 0;
int volatile EINT2 = 0;
void ExtInt_Serve1(void)__irq;
void ExtInt_Serve2(void)__irq;
/*----------------------------------< INT2 Initialization >------------------------------*/
void ExtInt_Init2(void)
{
EXTMODE |= 4;
//Edge sensitive mode on EINT2
EXTPOLAR = 0;
//Falling Edge Sensitive
PINSEL0 |= 0x80000000; //Enable
EINT2 on P0.15
VICVectCntl1 = 0x20 | 16; //Use VIC0 for
EINT2 ; 16 is index of EINT2
VICVectAddr1 = (unsigned long) ExtInt_Serve2; //Set Interrupt Vec Addr in VIC0
VICIntEnable |= 1<<16; //Enable
EINT2
}
/*----------------------------------< INT1 Initialization >------------------------------*/
void ExtInt_Init1(void)
{
EXTMODE |= 2;
//Edge sensitive mode on EINT1
EXTPOLAR = 0;
//Falling Edge Sensitive
PINSEL0 |= 0x20000000; //Enable
EINT1 on P0.15
VICVectCntl0 = 0x20 | 15; //Use VIC0 for
EINT1 ; 15 is index of EINT2
VICVectAddr0 = (unsigned long) ExtInt_Serve1; //Set Interrupt Vec Addr in VIC0
VICIntEnable |= 1<<15; //Enable
EINT1
}
/*----------------------------------< Serial Initialization >------------------------------*/
void Serial_Init(void)
{
PINSEL0 |= 0X00000005; //Enable Txd0 and Rxd0
U0LCR = 0x00000083; //8-bit data, no parity, 1-
stop bit
U0DLL = 0x00000061; //XTAL = 12MHz (pclk =
60 MHz, VPB = 15MHz(pclk=cclk/4)
U0LCR = 0x00000003; //DLAB = 0;
}
/*------------------------------------< Delay Function >----------------------------------*/
void DelayMs(unsigned int count)
{
unsigned int i,j;
for(i=0;i<count;i++)
{
for(j=0;j<1000;j++);
}
}
/*------------------------------------< Main Function >----------------------------------*/
void main(void)
{
Serial_Init();
ExtInt_Init1(); //Initialize Interrupt 1
ExtInt_Init2(); //Initialize Interrupt 2
putchar(0x0C);
printf ("***************** External Interrupt Demo
***************************\n\n\r");
DelayMs(100);
printf (">>> Press Interrupt Keys SW2(INT1) and SW3(INT2) for Output... \n\n\n\r");
DelayMs(100);
while(1)
{
DelayMs(500);
printf("INT1 Generated : %d | INT2 Generated : %d \r", EINT1, EINT2);
DelayMs(500);
}
}
/*----------------------------------< Interrupt Sub-Routine >------------------------------*/
void ExtInt_Serve1(void)__irq
{
++EINT1;
EXTINT |= 2;
VICVectAddr = 1;
}
void ExtInt_Serve2(void)__irq
{
++EINT2;
EXTINT |= 4;
VICVectAddr = 0;
}

You might also like