Eurocode2 Design Guide

for midas Gen

Integrated Design System for Building and General Structures
Introduction
This design example book provides a comprehensive guide for RC design as per Eurocode2-1-1:2002. Specifically,
this guide will review the design algorithms implemented in midas Gen, and go through design tutorials. This book is
helpful in understanding the Eurocode design concept and verifying design results using midas Gen.

CHAPTER 1 Why midas Gen

This chapter describes the main features and advantages of midas Gen and showcases
prominent project applications.

CHAPTER 2 RC Design Algorithms

This chapter discusses the general design concept of EN1992-1-1 and how it has been
implemented in midas Gen. T his enables the user to understand the equations,
formulas, program limitations and development scope of the midas Gen design
features.

CHAPTER 3 RC Design Tutorial

This chapter enables the user to get acquainted with the RC design procedure in midas
Gen as per EN1992-1-1: 2004. It encompasses the overall design procedure, from
generating load combinations to checking design results with updated sections.
 CHAPTER 1

Why midas Gen

Eurocode2 Design Guide for midas Gen
CHAPTER 1
Why midas Gen
CHAPTE R 1. Why midas Gen

2
CHAPTE R 1. Why midas Gen

3
CHAPTE R 1. Why midas Gen

4
CHAPTE R 1. Why midas Gen

5
CHAPTE R 1. Why midas Gen

6
 CHAPTER 2

RC Design Algorithm
Eurocode2 Design Guide for midas Gen
 CHAPTE R 2. RC Design Algorithm

Overview
1.1 Design Scope -------------------------------------------------------------------------------------------- 3
1.2 Materials ------------------------------------------------------------------------------------------------ 3
1.2.1 Concrete ........................................................................................................................................................... 3
1.2.1.1 Modulus of Elasticity (Ec)------------------------------------------------------------------------------------------4
1.2.1.2 Poissons Ratio -------------------------------------------------------------------------------------------------------4
1.2.1.3 Weight Density ------------------------------------------------------------------------------------------------------4
1.2.1.4 User Defined Materials --------------------------------------------------------------------------------------------5
1.2.2 Reinforcement ................................................................................................................................................. 5
1.2.2.1 Modulus of Elasticity (Es )------------------------------------------------------------------------------------------6
1.2.3 Design Strength of Materials ........................................................................................................................ 6
1.2.3.1 Design compressive strength of concrete (f cd) --------------------------------------------------------------6
1.2.3.2 Design yield strength of reinforcement (fyd) -----------------------------------------------------------------6
1.2.3.3 Short/Long Term Elasticity Ratio --------------------------------------------------------------------------------7
1.2.3.4 Partial Safety Factors for Materials -----------------------------------------------------------------------------8
1.3 Design Information -------------------------------------------------------------------------------------- 9
1.3.1 Member Assignment ...................................................................................................................................... 9
1.3.2 Unbraced Length ........................................................................................................................................... 10
1.3.3 Live Load Reduction Factor ......................................................................................................................... 10
1.3.4 Imperfections................................................................................................................................................. 11
1.3.5 P-Delta Analysis ............................................................................................................................................. 11
1.3.6 Pattern Loading ............................................................................................................................................. 12
1.3.7 Selection of Design Code ............................................................................................................................. 12
Ultimate Limit State
2.1 Design for flexure without axial force ------------------------------------------------------------------ 13
2.1.1 Requirements ................................................................................................................................................ 13
2.1.2 Calculating the moment capacity, MRd...................................................................................................... 13
2.1.3 Design Criteria for Rebars............................................................................................................................ 16
2.1.4 Concrete Checking for beams ..................................................................................................................... 17
2.1.4.1 Rebar Input for Beam Checking ------------------------------------------------------------------------------- 18
2.1.5 Design load combinations ........................................................................................................................... 18
2.2 Design for flexure with Axial Force --------------------------------------------------------------------- 19
2.2.1 Requirements ................................................................................................................................................ 19
2.2.2 Magnification of Design Moments ............................................................................................................ 19
2.2.2.1 Slenderness ratio-------------------------------------------------------------------------------------------------- 19
2.2.2.2 Limiting value of slenderness ratio --------------------------------------------------------------------------- 20
2.2.2.3 Magnification of Moments ------------------------------------------------------------------------------------- 21
2.2.3 Determination of the Eccentric Axial Load Capacity............................................................................... 22
2.2.4 Design Criteria for Rebars............................................................................................................................ 26
2.2.5 Concrete checking for columns & walls .................................................................................................... 26
2.2.5.1 Rebar Input for Column Checking ---------------------------------------------------------------------------- 26
2.2.5.2 Rebar Input for Wall Checking--------------------------------------------------------------------------------- 27
2.2.6 Design load combinations ........................................................................................................................... 27
2.3 Design for Shear---------------------------------------------------------------------------------------- 28
2.3.1 Requirements ................................................................................................................................................ 28
2.3.2 Calculation of Shear Resistance (VRd) ........................................................................................................ 28
2.3.2.1 Members not requiring design shear reinforcement ---------------------------------------------------- 28
2.3.2.2 Members requiring design shear reinforcement --------------------------------------------------------- 28
2.3.3 Design Criteria for Rebars............................................................................................................................ 30
2.3.4 Shear in Concrete Code Checking .............................................................................................................. 31
2.3.5 Design Load Combinations .......................................................................................................................... 31
 CHAPTE R 2. RC Design Algorithm

2.4 Verification of Design/Check Results ------------------------------------------------------------------- 31

2.4.1 Design Result Dialog box.............................................................................................................................. 31
2.4.2 Design/Check Reports .................................................................................................................................. 31
Serviceability Limit State
3.1 Serviceability Type Load Combination------------------------------------------------------------------ 34
3.1.1 Definition of Short Term and Long Term Load ......................................................................................... 34
3.1.2 Classification of Serviceability type Load Combinations........................................................................ 34
3.2 Serviceability Parameters ------------------------------------------------------------------------------- 35
3.3 Stress Limitation ---------------------------------------------------------------------------------------- 36
3.3.1 Stress Verification to avoid micro cracking............................................................................................... 36
3.3.1.1 Un-cracked Sections ---------------------------------------------------------------------------------------------- 36
3.3.1.2 Cracked Sections -------------------------------------------------------------------------------------------------- 37
3.3.2 Check for linear Creep .................................................................................................................................. 38
3.3.2.1 Uncracked Sections ----------------------------------------------------------------------------------------------- 38
3.3.2.2 Cracked sections--------------------------------------------------------------------------------------------------- 38
3.4 Crack width --------------------------------------------------------------------------------------------- 38
3.4.1 Calculate crack widths.................................................................................................................................. 38
3.4.2 Limiting Crack Width, wmax .......................................................................................................................... 39
3.4.2.1 Exposure Class ----------------------------------------------------------------------------------------------------- 40
3.5 Deflection Check ---------------------------------------------------------------------------------------- 40
3.6 Verification of Results----------------------------------------------------------------------------------- 40
3.6.1 Check Result dialog box ............................................................................................................................... 40
3.6.2 Design/Check Reports .................................................................................................................................. 40
Detailing Rules
4.1 Detailing rules for Beam Design ------------------------------------------------------------------------ 42
4.1.1 Longitudinal Reinforcement........................................................................................................................ 42
4.1.2 Shear Reinforcement.................................................................................................................................... 42
4.2 Detailing Rules for column design ---------------------------------------------------------------------- 43
4.2.1 Longitudinal Reinforcement........................................................................................................................ 43
4.2.2 Shear Reinforcement.................................................................................................................................... 43
4.3 Detailing Rules for Wall design ------------------------------------------------------------------------- 44
4.3.1 Vertical Reinforcement ................................................................................................................................ 44
4.3.2 Horizontal Reinforcement ........................................................................................................................... 44
 Chapter 2.1 RC Design Algorithm: EN1992-1-1:2004

Overview
1.1 Design Scope
midas Gen provides automatic design of concrete beam, column, shear wall, meshed slab and
meshed wall. The program also supports section checking when relevant data is specified. With
respect to Eurocode, the major capabilities of the program can be summarized as below:
Ultimate Limit State and Serviceability Limit State design and checking
Auto generation of load combinations as per Eurocode 1990:2002
Auto generation of Static Wind Loads as per Eurocode 1991-1-4:2005
Auto generation of Static Seismic Loads & Response Spectrum Functions as per Eurocode
1998-1:2004
Capacity design as per Eurocode 1998-1:2004
Available Section shapes for design:
o Beam: Rectangle, T-shape
o Column: Rectangle, Circular, Hollow circular
o Wall: Rectangle
Design and checking of meshed slab and meshed wall
Cracked section analysis of slabs for serviceability checks

The following should be taken care of by the user:

Torsion check is not provided by midas Gen.
Irregular wall such as L or H shape cannot be designed.
Isolated footing design is not supported as per EN 1992-1-1:2004.

This design guide covers the design of frame elements as per EN 1992-1-1:2004 for non-seismic
situations. Aspects of column design, beam design and wall design are discussed in this guide.
For the purpose of component design, midas Gen interacts with midas Design+. midas Design+ is a
collection of handy structural component design and detailing tools, which are easy to use and speed
up the day-to-day design process. midas Design+ is developed to be s imple, fast and accurate. It
enables engineers to systematically and consistently manage design reports. midas Design+ supports
Column design, Wall Design and Strip Footing Design as per Eurocode.

[Ta ble 1.1] Ca pabilities of midas Gen with respect to Eurocode

Ultimate Limit State Serviceability Limit State
Flexure Shear Axial Torsion Stress Deflection Crack Control
Beam
Column
Wall
Meshed Slab
Meshed Wall

1.2 Materials
1.2.1 Concrete
EN 1992-1-1:2004 (Table 3.1) provides specifications about strength and deformati on characteristics
of concrete. midas Gen supports a material database as per the specifications. Any of the materials
can be easily chosen for analysis as well as design. The following are the strength classes of concrete

3
 CHAPTE R 2. RC Design Algorithm

as identified by the code:

C12/15
C16/20
C20/25
C30/37
C35/45
C40/50
C45/55
C50/60
C55/67
C60/75
C70/85
C80/95
C90/105
Material name C40/50 implies that the cylinder characteristic strength (fck) at 28 days is 40 MPa and
cube characteristic strength (f ck,cube) at 28 days is 50 MPa.

The material can be chosen in Material Data dialog Box as shown below. In dialog box, choose Type
of Design as Concrete. Standard as EN04(RC). Then from DB drop down list any of the above
materials can be chosen.

1.2.1.1 Modulus of Elasticity (Ec)

For materials selected from EN 1992-1-1:2004, the modulus of elasticity is obtained using the
formula as specified by the code:
0.3
= 22 ( ) (1.1) EN1992-1-
10 1:2004
Table 3.1
= + 8 (MPa) (1.2)

Note for Italian users

For Italian user, the program supports the UNI material database. The database includes the
following materials:
Rck 10
Rck 15
Rck 20
Rck 25
Rck 30
Rck 35
Rck 40
Rck 45
Rck 50.
For these materials, the user needs to choose the Standard as UNI(RC) and then select the desired
material.

1.2.1.2 Poissons Ratio

The default value of Poissons ratio is used as 0.2. For a different value of Poissons ratio user defined
material needs to be specified as per Section 1.2.1.4 of this guide.

1.2.1.3 Weight Density

The weight density is used as 25 kN/m3 for all the material from the database. For a different weight
density user defined material needs to be specified as per Section 1.2.1.4 of this guide.

4
 CHAPTE R 2. RC Design Algorithm

Model > Properties > Material

[Figure 1.1] Material Data dialog box

1.2.1.4 User Defined Materials

User defined Concrete Material can be specified. Type of Design should be used as Concrete,
otherwise the design cannot be performed for the specified material . Then select the Standard as
None to input the user defined material properties. Type of design should not be selected as User
Defined.

1.2.2 Reinforcement
The reinforcement material can be specified in Modify Concrete Materials dialog box as shown in
Section 1.2.3. If the material is not specified there, then the default material will be taken as specified
in Design/Load Code Environment in Tools > Preferences. Then under Concrete heading user can
specify the database for Rebar. The available rebar materials as per Eurocode are as follow:
[Ta ble 1.2] Ava ilable Rebar Ma terials as per EN 1992-1-1:2004
Reba r Ma teri a l Yi el d Strength (f y ) (MPa )
Class A 400
Class B 500
Class C 600

Note for Italian users

For Italian users, the program supports the UNI database consisting of the following materials:
FeB22k
FeB32k
Feb38k
Feb44k
To select the above materials, we need to specify the Material Code as UNI(RC).

5
 CHAPTE R 2. RC Design Algorithm

Tools > Preferences

[Figure 1.2] Preferences dialog box

1.2.2.1 Modulus of Elasticity (Es)

For all the reinforcing materials, modulus of elasticity is used as 200 GPa. Different value of Modulus
of Elasticity cannot be specified for reinforcing materials .

1.2.3 Design Strength of Materials

EN1992-1-
1.2.3.1 Design compressive strength of concrete (fcd) 1:2004
The code specifies the following equation for the calculation of the design compressive strength: 3.1.6(1)

= (1.3)

where,
fck: If standard material is used, the value is taken automatically as specified in the code . For a
user defined material, we need to specify the fck in Modify Concrete Materials dialog box shown
below.
cc: Coefficient to account for:
1. Long term effects on the compressive strength
2. Unfavorable effects resulting from the way the load is applied.
It can be specified in the Partial Safety Factor for Materials dialog box as shown in Section
1.2.3.4.
c : The partial safety factor for concrete. It depends on the design situation. It can be specified in
the Partial Safety Factor for Materials dialog box as shown in Section 1.2.3.4.

1.2.3.2 Design yield strength of reinforcement (fyd)

EN1992-1-
The yield strength specified for reinforcing material will be used to calculate the design yield strength
1:2004
as per the following specification of code: 3.1.6(2)

= (1.4)

where,
fyk: The characteristic yield strength of reinforcement.
s : The partial safety factor for steel. It depends on the design situation. It can be specified in the
Partial Safety Factor for Materials dialog box as shown in Section 1.2.3.4.

6
 CHAPTE R 2. RC Design Algorithm

Design > Concrete Design Parameter > Modify Concrete Materials

[Figure 1.3(a)] Modify Concrete Material dialog box

In the above dialog box, the concrete and rebar material properties can be specified for design.
If standard material is used, the value is taken as specified in the code. In that case, this step is not a
mandatory step. If material is user defined, then select 'None' in the Code field and enter the name
of material to be used in the Name field. Then, each data field is activated and the strength of
materials can be entered.
Lightweight Concrete Factor (Lambda): This is irrelevant for design as per Eurocode.
Grade of Main Rebar: The material specified here will be used for the longitudinal reinforcement.
Grade of Sub Rebar: The material specified here will be used for the stirrups.

Design > Concrete Design Parameter > Modify Concrete Materials>

[Figure 1.3(b)] Short/Long Term Elasticity Ratio dialog box

1.2.3.3 Short/Long Term Elasticity Ratio

For serviceability check as per Eurocode 2, the ratios of the modulus of elasticity of reinforcement
to the modulus of elasticity of concrete for short-term and long term can be entered.
The default value for short-term ratio is Es/Ec and 2(Es/Ec) for long-term ratio.
The ratio can be edited in the Modify Concrete Materials Dialog Box. The button next to the Name
field, provides access to the Short/Long Term Elasticity Ratio dialog box.

7
 CHAPTE R 2. RC Design Algorithm

1.2.3.4 Partial Safety Factors for Materials

Design > Concrete Design Parameter > Partial Safety Factors for Material Properties

[Figure 1.4 Partial Factors for Material Properties dialog box]

[Ta ble 1.3] Recommended Va lues of Pa rtial Safety Fa ctors for Ma terials
Des i gn Si tua ti ons c s
Persistent & Transient 1.5 1.15
Accidental 1.2 1.0

As per EN1990:2002, design situations are classified as:

a. Fundamental Design Situations:
1. Persistent Design Situations
Relevant during design working life of structure
2. Transient Design Situation
Relevant for a shorter duration. eg: execution or repair
b. Seismic Design Situation
Relevant during the earthquake
c. Accidental Design Situation
Exceptional conditions like fire events, explosions, blast etc.
Specification 5.2.4(2) of EN1998-1:2004 If more specific data are not available, the values of the
partial factors c and s adopted for the persistent and transient design situations should be applied.
midas Gen uses the same values of c and s for all three design situations i.e Persistent, Transient &
Seismic Design Situations.

The design situation is identified automatically by the program as per the following table:
[Ta ble 1.4] Cl assification of Design Situations
Des i gn s i tua ti ons Des cri pti on
Fundamental and Load combinations not covered in Accidental Situation
Seismic
Accidental Load Combination including any of the following type of
load case, will be classified in Accidental Situation:
Live Load Impact (IL)
Collision Load (CO)

Load Case type is specified in the dialog box below:

8
 CHAPTE R 2. RC Design Algorithm

Load > Static Load Cases

[Figure 1.5] Static Load Cases dialog box

After identifying the design situation respective partial safety factors for materials are used by the
program in design.

1.3 Design Information

1.3.1 Member Assignment
The program offers to consider a number of line elements as a single member for the purpose of
design. The design forces and the section capacities will be calculated at the i, , , , j-point of the
member and not of the element. Also, the span for the design will be considered as per the
specifications of the member and not of the element.

The unbraced length will be taken on a member basis, instead of element basis. Laterally Unbraced
Length is taken from the member.

[Figure 1.6] Unbraced Length for column

If the elements to be assigned to a member retain different material and section properties, or the

9
 CHAPTE R 2. RC Design Algorithm

directions of the node connections are different, a member cannot be assigned.

Design > General Design Parameter > Member Assignment

[Figure 1.7 Member Assignment dialog box]

1.3.2 Unbraced Length

When members are defined by Member Assignment, unbraced lengths about the member s strong
axis (y-Axis) and weak axis (z-Axis) are automatically calculated by the program considering the
connectivity of the members.
If members are not defined then the unbraced length is taken equal to the length of the element for
bending about both axis.

The unbraced length can also be specified by the user in Unbraced Length dialog box as shown
below. If unbraced length is specified as 0, then progra m will take the unbraced length as the length
of the member or the length of the element, whichever is applicable.

Design > General Design Parameter > Unbraced Length

[Figure 1.8] Unbraced Length dialog box

1.3.3 Live Load Reduction Factor

When calculating the Forces for design, the effect of live load can be reduced. Axial force, moments
and shear forces due to actions can be reduced. The reduction factor can be specified in the Modify
Live Load Reduction Factor dialog box. In order to specify the live load to be reduced to 80%, the
factor of 0.8 should be added for the respective forces.

10
 CHAPTE R 2. RC Design Algorithm

Design > General Design Parameters > Modify Live Load Reduction Factor

[Figure 1.9 Modify Live Load Reduction Factor dialog box]

The live load reduction factor needs to be calculated manually. The formula specified by EN 1991-1-
1:2002 is: EN 1991-1-
2+ (+2)0
= (1.5) 1:2002
6.3.1.2(11)
where:
n is the number of storys (>2) above the loaded structural elements from the same category.
0 is the factor for combination of variable actions. It is provided in EN 1990, Annex A1, Table
A1.1.

1.3.4 Imperfections
Eurocode 1992-1-1:2004 specifies that the unfavorable effects of possible deviations in the geometry
of the structure and the position of loads shall be taken into account in the analysis of members and
structures. The imperfections should be modelled manually by the user.
In order to consider the effect of these imperfections, the code provides equivalent transverse forces
for these imperfections in Section 5.2 using equations from 5.4 to equation 5.6. These forces need
to be calculated and applied manually by the user.

1.3.5 P-Delta Analysis

The amplification of the moments due to second order effects is specified by the code. Second order
effects due to both the change of geometry of structure (P-) and the curvature of member (P-)
need to be considered.
The second order effects can be easily considered in the program by performing P-Delta Analysis.
The program performs both P- as well as P- analysis. The corresponding magnified moments can
be used for the design of the members. In case the P-delta analysis is not performed, the provisions
of code will be used to obtain the second order moments . The method of moment magnification as
per Eurocode 2 will be discussed in Section 2.2.

11
 CHAPTE R 2. RC Design Algorithm

Analysis > P-Delta Analysis Control

[Figure 1.10] P-Delta Analysis Control dialog box

1.3.6 Pattern Loading

At the moment, the program doesnt support the auto generation of the pattern load combinations.

1.3.7 Selection of Design Code

The design code can be selected in the Concrete Design Code dialog box as shown below:

Design > Concrete Design Parameters > Concrete Design Code

[Figure 1.11] Concrete Design Code dialog box

In addition to the recommended values, the program supports the following National Annexes
for design:
Italy
Sweden
Singapore

12
 Chapter 2.2 RC Design Algorithm: EN1992-1-1:2004

Ultimate Limit State

2.1 Design for flexure without axial force
2.1.1 Requirements
Moment capacity of the section (MRd) should be greater than the design moment for the section
(MEd).
To satisfy limit state of moment resistance the following condition should be met:
MEdMRd

2.1.2 Calculating the moment capacity, MRd

The distribution of strain and stresses in the section is as follows:

Ref:
EN 1992-1-1:2004
Figure 3.5

[Figure 2.1] Distribution of strain and stresses in the section

where,
: factor defining the effective height of the compression zone.
: factor defining the effective strength of concrete.
x: distance of the neutral axis from the extreme compression fiber

To calculate the moment capacity Cc, Cs and Ts are required. In order to determine all these forces
depth of the neutral axis, x, needs to be calculated.
For this, an iterative process is used. The following steps are involved in the iteration:

Initial value of x=d/2

Assume neutral Axis depth, x (d = effective depth)

Calculate Cc (concrete compression)

No
Calculate Ts (tension in steel)
Calculate Cs (compression in steel)

Cc + Cs = C ; Ts = T ; C-T=0

Yes
Assumed x is the depth of neutral axis
13
 CHAPTE R 2. RC Design Algorithm

[Figure 2.2] Flow chart to calculate depth of Neutral Axis

Note for design of flanged section
For a flanged section, we need to specify the shape of the section as T-section in the Section
Data dialog box.

EN1992-1-1:2004
1. Determination of & 3.1.7(3)
[Ta ble 2.1] Fa ctor for effective height of compression zone a nd factor for effective s trength of concrete
Condi ti on
fck 50MPa 0.8 1.0
50 < fck 90MPa 0.8-(fck-50)/400 1.0-(fck-50)/200
fck > 90MPa 0.7 0.8

2. Initial depth of the neutral axis.

Initial depth is assumed to be d/2, where d is the distance between extreme compression
fiber and center of tension reinforcement.

3. Calculate force of concrete, Cc

= (2.1)

4. Calculate force of reinforcement, Ts and Cs

= (2.2)
= (2.3)
where,
Asc: The cross sectional area of compressive reinforcement.
fsc: The stress at the center of the compressive reinforcement.
Ast : The cross sectional area of tensile reinforcement.
fst : The stress at the center of the tensile reinforcement.

In order to calculate the stress of reinforcing steel, f st or fsc, the appropriate strain is
calculated by the strain compatibility condition as follows:
a) At the extreme compression fiber of concrete, strain equal to cu is assumed. Then the
strain is calculated at the center of reinforcement assuming a li near stress strain
distribution as per Figure 2.1.
dt x
s cu (2.4)
x
where,
s : The strain at the level of the reinforcement.
cu : The ultimate compressive strain in the concrete. ( cu = cu1 )
x : Neutral axis depth.
d t : Distance of the rebar from extreme compression fiber

[Ta ble 2.2] Ul timate Strain ( cu1) i n Concrete EN1992-1-1:2004

Table 3.1
Condi ti on cu1
fck 50MPa 0.0035
50 < fck 90MPa [2.8+27{(98-fcm)/100}4 ]/1000, fcm=fck+8MPa
fck > 90MPa 0.0028

14
 CHAPTE R 2. RC Design Algorithm

EN1992-1-1:2004
Figure 6.1

[Figure 2.3] Possible strain distributions in the ultimate limit state

b) Calculate the reinforcement stresses corresponding to the calculated reinforcement

strains. (from the stress-strain idealizations)
s E s ( s yd )
fs (2.5)
f yd ( s yd )
The forces of tensile reinforcement and compressive reinforcement are calculated in the
above manner.

5. Check if the assumed depth of neutral axis is suitable or not. For this purpose, the
convergence criteria is checked. If the following condition is met, then the assumed x is
used as depth of neutral axis :

| | < 0.01 (Tolerence)

If aforementioned condition is not fulfilled then, new depth of neutral axis is assumed by
Bisection Method (Numerical analysis).
If the above criteria is not met after 20 iterations, then:
We get output Not converge in Message window.
The model needs to be modified as follows:
o Increase section size.
o Modify the rebar information (position, numbers, spacing, etc.)

6. Calculate moment resistance MRd

Once the neutral axis is obtained, moment resistance can be calculated by multiplying the axial
forces with eccentricity from the neutral axis.
MRd = Ccac + Cs asc + Ts ast (2.6)

Cs
Asc
a cCc a sc
x

a st
Ast Ts
[Figure 2.4] Forces and distances from neutral axis depth for MRd

7. Check moment resistance ratio:

1

where,

15
 CHAPTE R 2. RC Design Algorithm

MEd : Design bending moment is chosen for the load combinations which are available as per
Section 2.1.5.
MRd : Moment capacity of the section.
Depending on the ratio, the results are displayed in the various forms as mentioned in Section
2.4.

2.1.3 Design Criteria for Rebars

To choose the size of the rebars which should be used for the reinforcement, the specifications
can be provided in Design criteria for Rebars dialog box as shown below.
The transverse reinforcement data can also be specified in this dialog box.

Design > Concrete Design Parameter > Design Criteria for Rebars

[Figure 2.5] Design Criteria for Rebars dialog box

where,
dT represents the distance between center of top rebar and extreme top fiber
dB represents the distance between center of bottom rebar and the extreme bottom fiber
When the value of dT and dB is specified as zero, then the default value is taken as minimum of:
I. max [Hc/10, Bc/10, 2.5/63.5 mm]
II. 3/76.2 mm

16
 CHAPTE R 2. RC Design Algorithm

Design > Concrete Design Parameter > Design Criteria for Rebars > Rebar

[Figure 2.6] Rebar Size dialog box

The following European rebar sizes are available:

P5, P6, P7, P8, P9, P10, P11, P12, P13, P16, P20, P25, P32, P40.
Maximum of 5 Rebar Sizes can be selected.

The data specified above will be applied to all the members of a model. If the user wants to
specify different rebar criteria for certain members then that can be specified in Design Criteria
for Rebars by Member dialog box. For that member, information provided here will override the
information defined in Design Criteria for Rebar dialog box.

Design > Concrete Design Parameter > Design Criteria for Rebar by Member

[Figure 2.7] Design Criteria for Rebars by Members dialog box

2.1.4 Concrete checking for beams

midas Gen is capable of both design and checking of sections. The difference in design and check
can be explained as below:
17
 CHAPTE R 2. RC Design Algorithm

If the user performs the Concrete Code Design function then based on the section size and the
factored load, rebar data such as rebar size and spacing is determined by the program. Therefore,
the design can be performed when the section size is defined without rebar data.
If the user needs to perform the strength and serviceability check for the user specified rebar
data (rebar diameter, number of rebars and design parameters), then the user can perform the
Concrete Code Check function. The rebar data can be specified as mentioned in the section
below.

2.1.4.1 Rebar Input for Beam Checking

The rebar data for concrete code checking can be specified in the Modify Beam Rebar data. In
midas Gen, both top and bottom rebar must be defined to perform concrete code checking.

The data can be entered for layer 1 and layer 2 of the top and the bottom reinforcement.
The values of dT and dB need to be specified appropriately. dT and dB cannot be specified as
zero.
For transverse reinforcement the rebar size, number of legs and spacing of the stirrups can be
specified.

Design > Concrete Design Parameter > Modify Beam Rebar Data

[Figure 2.8] Modify Beam Rebar Data dialog box

2.1.5 Design load combinations

The load combinations specified as Strength/Stress in the Concrete Design tab of Load
Combinations dialog box will be used for concrete design. The program also supports the Auto
Generation of the load combinations as per EN 1990:2002. The limitations mentioned in the
Section 1.3.6 are applied to the auto generation of the load combinations.

18
 CHAPTE R 2. RC Design Algorithm

Results>Load Combinations

[Figure 2.9] Load Combinations dialog box

2.2 Design for flexure with Axial Force

2.2.1 Requirements
For limiting the compressive strain in concrete, the following conditions need to be checked:

Check for Axial Force 1


Check for Biaxial Moment 1


Check for Moment about major axis 1


Check for Moment about minor axis 1

If any of the above ratios is not satisfied then the section is reported to be Not Good.

2.2.2 Magnification of Design Moments

When an element is subjected to an axial load combined with a moment, it will deflect. This
deflection will increase the moment at any section in the element by an amount equal to the
axial force multiplied by the deflection at that point. This extra moment will cause the resistance
of the element to be reduced below that calculated ignoring the deflections. In many practical
situations, the effect of deflections is so small that it can be ignored. So, the program compares
the slenderness ratio of the member with the allowable slenderness limit in order to determine
whether the magnification of moment is required or not.

2.2.2.1 Slenderness ratio

The actual slenderness ratio of a member is calculated using: EN1992-1-1:2004
5.8.3.2(1)
= l0 / I (2.7)
where,
l0 is the effective length of the member.
i is the radius of gyration.

Effective Length will be calculated as:

l o,y = Ky x L (2.8)
where,
19
 CHAPTE R 2. RC Design Algorithm

L is the unbraced length as specified in Section 1.3.2.

Ky is the effective length factor. The effective length factor can be specified as shown
below.

Design > General Design Parameter > Effective Length Factor (K)

[Figure 2.10] Effective Length Factor dialog box

Effective Length factor can also be calculated by the program automatically depending on the
information provided in Definition of Frame dialog box as shown below:
Refer to online help for the explanation of auto calculation.

Design > General Design Parameters > Definition of Frame

[Figure 2.11] Definition of Frame dialog box

2.2.2.2 Limiting value of slenderness ratio

EN1992-1-1:2004
.. 5.8.3.1(1)
= (2.7)

where,
A = 1/(1+0.2ef ). It can be specified by user. Default value is 0.7 ( code recommendation)
B = 1 + 2. It can be specified by user. Default value is 1.1 (code recommendation)
C = 1.7 - rm.
rm = M01 /M02
M01 and M02 are end moments of column. M02 is numerically greater of both. M01/M02
> 0 for single curvature bending and less than 0 for double curvature bending.
Code recommends that If rm is not known, C=0.7 may be used. Constant value of C can be
specified. Also, the program can calculate the factor C and r m based on M01 and M02.
n = NEd /Ac fcd. this is the normalized normal force.

20
 CHAPTE R 2. RC Design Algorithm

Design > Concrete Design Parameter > Concrete Design Code

[Figure 2.12] Concrete Design Code dialog box

2.2.2.3 Magnification of Moments

The slenderness ratio, (as obtained in 2.2.2.1) is compared to limiting slenderness ratio, min. If
P- Analysis has not been performed and > min, then the moments are magnified as per the
specifications of the code in order to account for the second order moments. If < min or P-
Analysis has been performed, then the specifications of the code are not used to magnify the
design moments.

EN 1992-1-1:2004 specifies the following two methods of moment magnification.

i. Based on Nominal Stiffness
ii. Based on Nominal Curvature
midas Gen uses Nominal Curvature Method.
EN1992-1-1:2004
As per Nominal Curvature Method, the overall design moment, M Ed is computed as: 5.8.8.2(1)

MEd = M0Ed + M2 (2.8)

where,
M0Ed = 0.6 M02 + 0.4 M01 0.4 M02

This is valid only if no transverse load exists between supports. In case the transverse load exists
between the supports, M0Ed = M02. In that case, it is recommended to perform P- Analysis.
M2 = NEd x e2 M2 is the additional second order moment.
where,
e2 = (1/r)l 0 2 /c e2 is the deflection.
l0 is effective length as specified in Section 2.2.2.1.
c depends on curvature distribution, program uses c = 10 as recommended by code.
The value of c cannot be changed by user.
1/r = Kr K 1/r 0 Curvature
Kr = (nu-n)/(nu-nbal) Correction factor for axial load
n = Ned/Ac fcd Relative axial force.
nu = 1 +
= 0.105. (Recommended) Different value cannot be specified.
nbal = 0.4 (Recommended) Different value cannot be specified.
21
 CHAPTE R 2. RC Design Algorithm

K = 1 (Factor for accounting creep)

1/r 0 = yd/(0.45d)
yd = fyd/Es
The above calculations are performed for major and minor directions separately.
For the wall the magnification is performed for in-plane bending. If design is also performed for
out-of-plane bending, then the above check will also be performed for out-of-plane bending. The
choice of design for out-of-plane bending can be specified in Input Additional Wall Data dialog
box.

2.2.3 Determination of the Eccentric Axial Load Capacity

The following procedure is followed to determine the eccentric load capacity of the column:
1. Calculate the eccentricities of bi -axially loaded column:
ecy = |MEdz /NEd|
ecz = |MEdy/NEd|
e = |MEd/NEd|
Angle of axis of bending = tan-1 |Ecy/Ecz |
Angle of rotation of neutral axis at the ultimate limit state is determined by the program.

MEdy NEd

e cz
e
e cy
MEdz

[Figure 2.13] Forces and Moments on a member w ith eccentric axial load
where,

MEd = 2 + 2

2. Calculate the axial load capacity for concentric loading

Maximum Axial Compression
NRd = (.fcd).(Ag-Ast) + fyd.Ast (2.9)
where,
NRd is Axial load (compression) capacity for concentric loading
is the factor for effective strength of concrete
fcd is design strength of concrete as mentioned in Section 2.1.3
Ag is the gross area of column Ag = b . h
Ast is the total area of steel in column.
fyd is design yield strength of steel as mentioned in Section 2.1.3

Maximum Axial Tension

NRdt = -fyd . Ast (2.10)
where,
NRdt is Axial Load (Tension) Capacity for concentric loading
fyd design yield strength of steel
Ast is the area of steel

3. Compute capacity of concrete stress block.

Height of compression zone
X is the height of the compression zone. For the first trial, the balanced failure is assumed hence
X=c b.

cb = d Ast (2.11)
+
where,
cb is the depth of neutral axis for section failing in balanced condition
d is the distance of extreme compression fiber from farthest reinforcement
22
 CHAPTE R 2. RC Design Algorithm

dzi

d si
dyi
z cu

X
x fcd
d

s
a= X

Neutral Axis

[Figure 2.14] Stress strain distribution in concrete column w ith eccentric axial load

Effective height of compression zone

a = . X Ast (2.12)
where,
is the factor for effective height of compression zone.
Acom is the effective area of concrete in compression. It is calculated based on a.

Compression Force in Concrete

Cc = x fcd x Acom Ast (2.13)

Moment due to compression force

MRdCy = Cc . DCcz (2.14)
MRdCz = Cc . DCcy (2.15)
where,
DCcy is distance of centroid of compression zone from geometric center of
section along y-axis
DCcz is distance of centroid of compression zone from geometric center of
section along z-axis

4. Compute capacity of reinforcement

Fsi is force of the ith reinforcement
Fsi = Asi . fsi (2.16)
where,
fsi is stress in the i th reinforcement
s E s ( s yd )
fs
f yd ( s yd )
where,
si is strain in the i th reinforcement
At the extreme compression fiber of concrete, strain equal to cu is
assumed. Then the strain is calculated at the center of reinforcement
assuming a linear stress strain distribution as shown in Figure 2.14.
Asi is the area of the i th rebar
Moment due to force in rebar
i. About the element local y-axes
MRdNyi = Fsi x dzi (2.17)
ii. About the element local z-axes
MRdNzi = Fsi x dyi (2.18)
23
 CHAPTE R 2. RC Design Algorithm

where,
d zi is distance of i th reinforcement from the geometric center of the section
in the element local z-axis (as shown in Figure 2.14)
d yi is distance of i th reinforcement from the geometric center of the section
in the element local y-axis (as shown in Figure 2.14)

Cumulative axial force and moment resistance

Axial force and the moment due to all the rebars are calculated as follows:
Ns = (Fsi)
MRdNy = (MRdNyi)
MRdNz = (MRdNzi)

5. Compute capacity (NRd,MRd) of the section

NRd = Cc + Ns dyi (2.19)
MRdy = MRdCy + MRdNy
MRdz = MRdCz + MRdNz
2 2
MRd = +
6. Compare the eccentricity with the actual eccentricity
Eccentricity
ec = MRd/NRd
Actual eccentricity
e = MEd/NEd
If ec = e, then X is the height of the compression zone. For the first trial ec = eb (balanced
eccentricity).
Otherwise new depth is assumed.
Then new value of X is assumed as follow:
e < eb, then section is compression controlled and larger value of x is assumed.
e > eb, then section is tension controlled and smaller value of x is assumed.

[Figure 2.15] Comparison of Tension Controlled and Compression Controlled Column

7. Check P-M Curve

The P-M curve is generated for a fixed angle of rotation of neutral axis.

24
 CHAPTE R 2. RC Design Algorithm

[Figure 2.16] 2D PM Interaction Curve

3D PM Curve is generated by changing the angle of rotation of neutral axis as follows:

[Figure 2.17] 3D PM Interaction Curve

The output is given in the form of 2-D P-M Interaction Curve as well as 3-D P-M-M Interaction
Curve.

Check the ratio

The following ratios are checked to verify the capacity of the axially loaded member
(wall/column):

1


1


1


1

where,

25
 CHAPTE R 2. RC Design Algorithm

MEd : Design bending moment is chosen for the load combinations which are available as per
2.1.5.
MRd : Moment Capacity of the section.
Depending on the ratio, the results are displayed in various formats box as mentioned in Section
2.4.

2.2.4 Design Criteria for Rebars

To choose the size of the rebars that should be used for providing the reinforcement, the
specifications can be provided in Design criteria for rebars dialog box as shown in Section 2.1.3.
The stirrup data can also be specified in this dialog box.
Data can be specified for both wall and column design.
For wall design the End rebar design method and the spacing of the end rebar can be specified in
Input Additional Wall Data dialog box as shown below:

Design > Concrete Design Parameter > Modify Column Rebar Data

[Figure 2.18] Input Additional Wall Data dialog box

2.2.5 Concrete checking for columns & walls

Concrete Code Checking can be performed for column members & wall members as well. The rebar
data can be specified for axially loaded members and Ultimate Limit State and Serviceability Limit
State can be verified based on that rebar data.

2.2.5.1 Rebar Input for Column Checking

The rebar data for the column can be specified in Modify Column Rebar Data dialog box as shown
below.

26
 CHAPTE R 2. RC Design Algorithm

Design > Concrete Design Parameter > Modify Column Rebar Data

[Figure 2.19] Modify Column Rebar Data dialog box

2.2.5.2 Rebar Input for Wall Checking

The rebar data for the wall can be specified in Modify Wall Rebar Data dialog box as shown below.

Design > Concrete Design Parameter > Modify Wall Rebar Data

[Figure 2.20] Modify Wall Rebar Data dialog box

2.2.6 Design load combinations
The specifications in Section 2.1.5 are applied.
27
 CHAPTE R 2. RC Design Algorithm

2.3 Design for Shear

2.3.1 Requirements
Shear resistance of the section (VRd) should be greater than the design shear force for the section
(VEd).
To satisfy Limit state of Shear Resistance the following condition should be met:
VEdVRd

2.3.2 Calculation of Shear Resistance (VRd)

If VEd is smaller than the shear resistance of concrete, then shear reinforcement is not required
and shear resistance is calculated by concrete only. If design shear force exceeds shear resistance
calculated from concrete then the shear resistance is calculated by shear reinforcement only.

Calculate VRd,c

Yes No
VEd > VRd,c?

Shear Reinforcement required. Shear Reinforcement not required.

Calculate VRd,s VRd = VRd,c
VRd = VRd,s VRd = VRd,s
[Figure 2.21] Flow chart to calculate V Rd

2.3.2.1 Members not requiring design shear reinforcement

In member for which VEdVRd,c, no shear reinforcement is required. In those members the program
provides the minimum specified shear reinforcement as per Section 4.1.2 and 4.2.2.
For such sections, the shear resistance
VRd = VRd,c dyi (2.20)
For calculating the design shear resistance of concrete, larger of the following two values is
adopted: EN1992-1-1:2004
6.2.2(1)
, = [, (100 )1/3 + 1 ] (2.21)
3/2 1/2
, = [0.035 + 1 ] (2.22)
where,
CRd,c = 0.18/c
= 1 + 200/ 2.0
l = Asl /(b wd) 0.02
cp = NEd /Ac, In beam design, cp is applied as zero since axial force is not
considered.
k 1 = 0.15
Asl i s the a rea of the tensile reinforcement, which extends (l bd + d) beyond the section
cons idered. For beam section, program considers Asl as the area of the tensile reinforcement provided. For
col umn s ections, the Asl i s used as the Ast/2 i.e half of the a rea of the l ongitudinal reinforcement.

2.3.2.2 Members requiring design shear reinforcement

For the members for which the design shear force exceeds the shear resistance provided by
concrete, the shear resistance is calculated as the resistance provided by shear reinforcement.
VRd = VRd,s + Vccd + Vtd (2.23)
where,
Vccd :shear component of the force in the compression area, in the case of inclined compression EN1992-1-1:2004
chord. 6.2.1(2)
Vtd : shear component of the force in the tensile reinforcement, in the case of inclined tensile chord.
28
 CHAPTE R 2. RC Design Algorithm

[Figure 2.22] Shear component for members w ith inclined chords

Since, inclined chord is not considered therefore the shear resistance is calculated using shear
reinforcement only.
VRd = VRd,s (2.24)

Design of shear reinforcement is based on truss model as specified in Section 6.2.3 of EN 1992 -1-
1:2004

[Figure 2.23] Truss model and notation for shear reinforced members

is the angle between the concrete compression strut and the beam axis perpendicular to the
shear force. is the angle between shear reinforcement and the beam axis perpendicular to the
shear force. The program provides the shear reinforcement perpendicul ar to the beam axis. So,
= 90 o. Any other value of cannot be specified by the user.
can be specified by user in Concrete Design Code dialog box as explained below:

Design > Concrete Design Parameters > Design Code

[Figure 2.24] Concrete Code Design dialog box

Shear resistance of members with shear reinforcement can be calculated depending on the type
of shear reinforcement as specified in the table below.

[Ta ble 2.3] VRd,s a nd VRd,max, Asw,max

Pa ra meter Formul a Rema rks
VRd,s (0.9 ) Asw is cross-sectional area of the shear reinforcement.
cot
s is the spacing of stirrups.

VRd,max (0.9 ) fywd is design yield strength of the shear reinforcement.

EN1992-1-1:2004
1 1 is Strength reduction factor for concrete cracked in shear.
cot + tan 6.2.3(4)
cw is Coefficient taking account of the state of the stress in
Asw,max 0.5 1 the compression chord. cw is always applied as 1.0 in beam EN1992-1-1:2004
design.
6.2.3(3)

Using, VRd,s = VEd, spacing s of the shear reinforcement is calculated.

29
 CHAPTE R 2. RC Design Algorithm

VRd,max is the design value of the maximum shear force which can be sustained by the member,
limited by crushing of the compression struts.
Asw/s is calculated and compared with Asw,max/s.

[Ta ble 2.4(a )] Strength reduction factor for concrete cra cked i n s hear, 1
fywd< 0.8fywk
Na ti ona l Annex f ywd 0.8fywk
fck < 60MPa fck 60MPa
f f ck
Recommended 0.61 ck 0.6 0.9 0.5
250 200

f (0.84-fck/200)(1-0.5 cos)
0.61 ck 0.54(1-0.5 cos)
Singapore 0.5
250 = 0.54
= (0.84-fck/200) 0.5
[Ta ble 2.4(b)] Strength reduction factor for concrete cracked in shear, 1
fywd 0.8fywk fywd< 0.8fywk
Na ti ona l Annex
fck 70MPa fck > 70MPa fck < 60MPa fck 60MPa

f 0.9
f ck
Italy 0.5 0.7 1 ck 0.7 200 0.5
250 0.85

[Ta bl e 2.5] Recommended values of Coefficient cw

Condi ti on cw
0<cp 0.25fcd 1+cp/fcd
0.25 fcd <cp 0.5fcd 1.25
0.5 fcd <cp 1.0fcd 2.5(1-cp/fcd)

cp : The mean compressive stress, measured positive, in the concrete due to the design axial force. In
beam design, cp is applied as zero since axial force is not considered.

2.3.3 Design Criteria for Rebars

Size of the rebar to be used for providing the shear reinforcement can be specified in Design
Criteria for Rebars dialog box. The number of legs to be used for shear reinforcement can also
be specified.

Design>Concrete Design Parameter> Design Criteria for Rebar

[Figure 2.25] Design Criteria for Rebars dialog box

30
 CHAPTE R 2. RC Design Algorithm

2.3.4 Shear in Concrete Code Checking

When Beam Checking or Column checking is performed, then checks for shear are also applied . The
data for the transverse reinforcement can be specified in the program. The data can be specified in
Modify Beam Rebar Data, Modify Column Rebar Data and Modify Wall Rebar Data dialog box. Refer
to section 2.1.4.1, 2.2.5.1 and 2.2.5.2 for the usage of these dialog boxes. The program allows the user
to specify rebar size, rebar spacing and the number of legs for stirrup.
For beams the data can be specified for i -end, j-end and the middle section.
For columns the same data can be specified for the two ends of the member and different data can
be specified for center of the column.

2.3.5 Design Load Combinations

The specifications of section 2.1.5 are applied.
In case the shear reinforcement is required, the governing Load combination for shear design is
not decided on the basis of the magnitude of the shear force. The governing load combination is
decided on the basis of the ratio of the shear force and shear capacity.
Now, if there are two shear forces VEd1 and VEd2 such that VEd1 >VEd2 . VRd,s (Shear Strength provided
by steel) and VRd,c (Shear Strength provided by concrete) will be calculated. If VEd1 /VRd,s is less than
the VEd2 /VRd,c, then VEd2 will be governing load combination for shear design, even if VEd2 is smaller
of the two shear forces.

2.4 Verification of Design/Check Results

midas Gen provides the results of design/check in various formats. The following design outputs
are available.

2.4.1 Design Result Dialog Box

The design results can be checked in Beam Design Result Dialog/Column Design Result Dialog/
Wall Design Result Dialog box as shown below.

Design > Concrete Code Design > Beam Design

[Figure 2.26] Beam Design Result dialog box

Similarly, the design results can be checked for column and walls. The dialog box for design results
of column members can be accessed from Design > Concrete Code Design > Column Design.
The dialog box for design results of wall can be accessed from Design > Concrete Code Design >
Wall Design.

2.4.2 Design/Check Reports

31
 CHAPTE R 2. RC Design Algorithm

The program provides the results in the following kind of report formats:
i. Graphic Report
ii. Detail Report
iii. Summary Report

[Figure 2.27] Graphic Report for Beam Design

[Figure 2.28] Detailed Report for Beam Design

32
 CHAPTE R 2. RC Design Algorithm

[Figure 2.29] Summary Report for Beam Design

33
 Chapter 2.3 RC Design Algorithm: EN1992-1-1:2004

Serviceability Limit State

The serviceability limit state is verified only when we perform Concrete Code Check. It is not verified
when Concrete Code Design is performed.

3.1 Serviceability Type Load Combination

The load combinations specified as Serviceability in the Concrete Design Tab of Load Combinations
dialog box will be used for serviceability limit state check. The program supports the auto generation of
the load combinations as per EN 1990:2002.

3.1.1 Definition of Short Term and Long Term Load

For the purpose of crack control, the Load Cases need to be specified as either short term load or
long term load.

Depending on the type of the load case, the program classifies the load cases automatically.
Information regarding the classification of load cases can be viewed/modified in Short/Long term
Load Case dialog box as shown below.

[Ta ble 3.1] Cl assification of load based on duration

Type of l oa d Des cri pti on
Long term If the load case is any of the following types, it is classified as long term:
D: Dead Load
L: Live Load.
LR: Roof Live Load.
IL: Live Load Impact
Short term If the type of load case is other than specified above, then it will be
classified as short term load case

Design> General Design Parameter > Short/Long term Load Case

[Figure 3.1] Short/Long term Load Case dialog box

If a load combination consists of any of the short term load case then the load combination will be
classified as short term type. Otherwise it will be classified as long term type.

3.1.2 Classification of Serviceability type Load Combinations

EN 1990:2002 classifies the serviceability type load combinations in following three types:
i. Quasi-Permanent
ii. Frequent
iii. Characteristic

34
 CHAPTE R 2. RC Design Algorithm

The load combinations that are auto generated are automatically classified in the above types. The
information regarding the classification of the load combinations can be viewed/modified in
Serviceability Load Combination Type dialog box as shown below.

Design> General Design Parameter > Serviceability Load Combination Type

[Figure 3.2] Serviceability Load Combination Type dialog box

3.2 Serviceability Parameters

Various parameters should be specified for performing the serviceability limit state check. The
default parameters are known to the program. Depending on the national annex selected in
Concrete Design Code dialog box, the parameters are automatically updated. The parameters can
be viewed/modified in the program.

Design> General Design Parameter > Serviceability Parameters

[Figure 3.3] Serviceability Parameters dialog box

35
 CHAPTE R 2. RC Design Algorithm

3.3 Stress Limitation

The compressive stress in concrete should be limited to avoid:
i. formation of micro-cracks which might reduce durability
ii. excessive creep
The program applies the stress checks for both situations. The first step in applying the stress check
is to determine whether the section is cracked or uncracked for the applicable load cases. The
section is uncracked if the following criteria is fulfilled:

c (tension) ca (tension)
where,
c (tension) = Mu Zbar /Iyy, stress in extreme tension fiber
Mu is the bending moment for a load combination.
Zbar is the distance of Neutral Axis from extreme tension fiber.
Iyy is the moment of inertia.
I yy and Zbar are calculated assuming elastic behavior of concrete in an uncracked transformed
EN1992-1-1:2004
section. 3.1.8(1)
ca (tension) = max [fctm , (1.6-h/1000)fctm] (3.1)

[Ta ble 3.2] Mea n Value of Axi al Tensile Strength, f ctm EN1992-1-1:2004
Condi ti on fctm Table 3.1

C50/60 0.30fck2/3
> C50/60 2.12 ln(1+(fcm/10))

For column members c (tension) is calculated considering the axial load and the biaxial bending:
c (tension) = P u/Ac + (Muy Zbar)/I yy + (Muz Ybar) /I zz (3.2)

If c (tension) ca (tension), then the section is cracked. For cracked sections, the program updates
the section properties for stress check.

3.3.1 Stress Verification to avoid micro cracking

EN 1992-1-1:2004 specifies Longitudinal cracks may occur if the stress level under the characteristic EN1992-1-1:2004
combination of loads exceeds a critical value. In the absence of other measures it may be appropriate 7.2(2)
to limit the compressive stress to a value k 1 fck in areas exposed to environments of exposure classes EN1992-1-1:2004
XD, XF and XS and Unacceptable cracking or deformation may be assumed to be avoided if, under 7.2(5)
the characteristic combination of loads, the tensile stress in the reinforcement does not exceed k 3 fyk.
Therefore, to fulfill these two specification, program applies the stress check for both reinforcement
as well as concrete.
The stress verification is performed for characteristic type of serviceability load combinations. After
determining that whether the section is cracked or not, the appropriate method is applied as
explained below:

3.3.1.1 Un-cracked Sections

In order to satisfy the stress check for concrete, the following criteria should be met:
c (Comp.) ca (Comp.)

The stress is calculated at the extreme compression fiber of the section.

c (Comp.) = Mu*(H-Zbar)/I yy (3.3)

where,
Mu is the bending moment for a load combination.
(H-Zbar ) is the distance of Neutral Axis from extreme compression fiber.
Iyy is the moment of inertia.

I yy and Zbar are calculated assuming elastic behavior of concrete in an uncracked transformed
section.
For column members c (Comp) is calculated considering the axial load and the biaxial bending:
36
 CHAPTE R 2. RC Design Algorithm

c (Comp.) = P u/Ac + Muy (H-Zbar) /I yy + Muz (B-Ybar) /I zz (3.4)

where,
H is the whole depth of cross-section along z-axis.
B is the whole width of cross-section along y-axis.

The limiting value of the stress in concrete is calculated as:

ca (Comp.) = k1 fck (3.5)

k1 can be specified in Serviceability Parameters. The following values are automatically adopted:

[Ta ble 3.3] Coefficient k 1~ k 4

k1 k2 k3 k4
Recommended 0.6 0.45 0.8 1.0
Italy 0.6 0.45 0.8 0.9
Singapore 0.6 0.45 0.8 1.0
The parameter k4 is not used by the program.
In order to satisfy the stress check for reinforcement, the following criteria should be met:
s sa
Stress in reinforcement is calculated as below:
s = Mu*(d-zbar)*n/I yy (3.6)
n is the Long term ratio of modulus of Elasticity.
The limiting value of the stress in the reinforcement is calculated as:
sa = k3 fyk (3.7)
k3 can be specified in Serviceability Parameters as defined in Section 3.2.
For column members, the check is applied only for concrete. The stress in reinforcement is not
checked.

3.3.1.2 Cracked Sections

The stresses are calculated for various load cases using the suitable modular ratio and then they are
added to get the stresses due to the particular load combination.
The following components are used:
1. Dead Load Cases
c,D = Mu_D*zbar/Iyy
s,D = Mu_D *(d-zbar)*n/I cr (Long term ratio is used)
2. Live Load Cases
c,L = Mu_L*zbar/Iyy
s,L = Mu_L *(d-zbar)*n/I cr (Long term ratio is used)
3. Other Load Cases
c,E = Mu_E*zbar/Iyy
s,E = Mu_E *(d-zbar)*n/I cr (Short term ratio is used)
where,
Mu _D is the bending moment for a load combination.
(Zbar ) is the distance of Neutral Axis from extreme compression fiber.
Icr is the moment of inertia.

I cr and Zbar are calculated assuming elastic behavior of concrete in a cracked transformed section.
The neutral axis is located by equating moment of areas. Then the I cr is calculated about the neutral
axis.

Then the stress in concrete are calculated as:

c = c,D + c,L + c,E
s = s,D + s,L + s,E EN1992-1-1:2004
7.2(3)

For concrete, c k1 x fck

For steel, s k3 x fyk
If a column members is cracked, then this procedure is not carried out for it.

37
 CHAPTE R 2. RC Design Algorithm

3.3.2 Check for linear Creep

EN 1992-1-1:2004 specifies If the stress in the concrete under the quasi-permanent loads is less
than k2 fck, linear creep may be assumed. If the stress in concrete exceeds k 2 fck, non-linear creep
should be considered. After determining whether the section is cracked or not under quasi-
permanent load combinations, the appropriate method is applied as explained below:

3.3.2.1 Uncracked Sections

Method specified in 3.3.1.1 is used to calculate the compressive stress and the allowable
compressive stress.
Quasi-Permanent type of combinations are used.
The allowable stress is calculated as ca (comp.) = k2 x fck.
If c (comp.) ca (comp.) and s (comp.) sa (comp.) then linear creep may be assumed.

3.3.2.2 Cracked sections

Method specified in 3.3.1.1 is used to calculate the compressive stress and the allowable
compressive stress.
Quasi-Permanent Type of combinations are used.
The allowable stress is calculated as ca (comp.) = k2 x fck.
If c (comp.) ca (comp.) and s (comp.) sa (comp.) then linear creep may be assumed.
If the column member are cracked, then this procedure is not carried out for them.

3.4 Crack width

EN1992-1-1:2004
For beam sections, cracking shall be limited to satisfy the following condition. 7.3.4(1)
Crack width, wk Crack width limit, wmax
Crack width is only calculated if the stress in concrete at the extreme tension fiber exceeds the
allowable tension stress.

3.4.1 Calculate crack widths EN1992-1-1:2004

The crack width is calculated using the following formula: 7.3.4(2)

wk = Sr,max (sm cm) (3.8)

1. Determine sm-cm

f ct ,eff
s kt 1 p ,eff
p ,eff
e
s
sm cm 0.6 (3.9)
Es Es
where,
sm The mean strain in the reinforcement under the relevant combination of loads, including
the effect of imposed deformations and taking into account the effects of tensile
stiffening.
cm The mean strain in the concrete between cracks.
s The stress in the tension reinforcement.
e Es /Ecm .
k t A factor dependent on duration of the load.

[ Ta ble 3.4] Fa ctor k t

Condi ti on kt
Short term loading 0.6
Long term loading 0.4

As 12 Ap ' As
p ,eff (3.10)
Ac ,eff Ac ,eff

38
 CHAPTE R 2. RC Design Algorithm

Ap : The area of pre or post-tensioned. Since the tendon is not considered in program, Ap =0.
Ac,eff : The effective area of concrete in tension, b w x h c,ef .

, = min [2.5( ), , ] (3.11)
3 2

[Figure 3.5] Calculation of Effective tension area

2. Determine sr,max
The maximum crack spacing, s r,max is calculated as shown in the table below.
k1k2 k4
sr .max k3c (3.12) EN1992-1-1:2004
p ,eff 7.3.4(2)

where,
is bar diameter. In case different sizes are used, eq should be calculated as:

The program uses the of the outer layer.

c is cover to the longitudinal reinforcement.
k 1 : A coefficient accounting the bond properties of rebar (0.8 for high bond bars)
k 2 : Coefficient accounting for distribution of strain. (0.5 for bending)
k 3 : 3.4 (recommended values)
k 4 : 0.425(recommended values)
These values cant be changed.

3.4.2 Limiting Crack Width, wmax

For reinforced members without prestressing tendon, limiting values of crack width, wmax, are given
in the table below.
[Ta ble 3.5] Li miting Crack Width, w max
Expos ure Servi ceability Loa d combination Type
Cl a s s Quasi-Permanent Frequent Characteristic
X0 0.4 User defined
XC1
XC2 0.3
XC3
XC4
XD1 0.3
XD2 Not Checked
XD3
XS1 0.3
XS2
XS3
XF1* Not Checked
XF2*
XF3*
XF4*
XA1* 0.2
XA2*
XA3*

39
 CHAPTE R 2. RC Design Algorithm

3.4.2.1 Exposure Class

Exposure class can be specified in Serviceability Parameters as mentioned in Section 3.2.

3.5 Deflection Check

EN 1992-1-1:2004 specifies to apply deflection check for certain sections that do not meet the
depth/span ratio criteria. But midas Gen calculates the deflection for all the members and compares
the deflection with the allowable value irrespective of the span/depth ratio.
There is no deflection check for the complete structure. Deflection check is applied for each member
separately.
Deflection verification is performed by comparing the relative deflection of the member to
deflection limit. Deflection is verified for Quasi-permanent and Characteristic load combinations.
The limit value is specified by the user in Serviceability Parameter dialog box.

3.6 Verification of Results

The checking results can be checked in various formats in midas Gen.
3.6.1 Check Result dialog box
The checking results can be checked in Beam Checking Result Dialog box as shown below.

Design > Concrete Code Check > Beam Checking

[Figure 3.6] Beam Checking Result dialog box

Similarly, the checking results can be checked for column sections and walls. The dialog box for
checking results of column members can be accessed from Design > Concrete Code Check > Column
Checking. The dialog box for checking results of walls can be accessed from Design > Concrete
Code Check > Wall Checking.

3.6.2 Design/Check Reports

The program provides the results in the following kind of report formats:
i. Graphic Report
ii. Detail Report
iii. Summary Report

40
 CHAPTE R 2. RC Design Algorithm

[Figure 3.7] Graphic Report for Beam Checking

[Figure 3.8] Detail Report for Beam Checking

[Figure 3.9] Summary Report for Beam Checking

41
 Chapter 2.4 RC Design Algorithm: EN1992-1-1:2004

Detailing of Members
When the program provides the reinforcement to the section, then checks are applied for minimum
and maximum allowable area of steel. Minimum areas of reinforcement are given in order to
prevent a brittle failure, wide cracks and also to resist forces arising from restrained actions. Along
with that the program also applies the checks for the spacing of the rebars. There should be
sufficient space between the resulting bars of members to allow access for vibrators and good
compaction of the concrete. The details of these checks are discussed in this section.

4.1 Detailing rules for Beam Design

4.1.1 Longitudinal Reinforcement
The following specifications of EN1992-1-1:2004 are considered by the program while providing the
reinforcement.
Maximum area of longitudinal reinforcement is calculated as:
EN1992-1-1:2004
As,max = 0.04 Ac (4.1) 9.2.1.1 (3)

Minimum area of longitudinal reinforcement is calculated as:

As,min = 0.26 btd 0.0013btd (4.2) EN1992-1-1:2004
9.2.1.1(1)
where,
b t denotes the mean width of the tension zone. For rectangular sections, b t is equal
to section width. For a T-beam width of web is used by the program.
fctm is taken as specified in 3.1.

For providing the adequate spacing in the bars, the program takes care of the following code
specifications:
The clear distance (horizontal and vertical) between individual parallel bars or horizontal layers of
parallel bars should be not less than the maximum of:
i. k1 bar diameter
ii. (dg + k2 mm) where dg is the maximum size of aggregate.
iii. 20 mm
The recommended values of k 1 and k2 are used which are specified as 1 and 5 mm respectively.

4.1.2 Shear Reinforcement

Minimum required shear reinforcement is calculated by the program as below:

w,min = 0.08 / (4.3) EN1992-1-1:2004

9.2.2(5)
where,
w is the shear reinforcement ratio

The maximum longitudinal spacing between shear assemblies is taken as the minimum of:
s l,max = 0.75d (1 + cot ) = 0.75d (for =90 o) (4.4)
EN1992-1-1:2004
s = Asw / (bw . w,min) (4.5) 9.2.2(6)
where,
Asw is the area of shear reinforcement within length s
s is the spacing of the shear reinforcement
b w is the breadth of the web of the member
is the angle between shear reinforcement and the longitudinal axis. It is applied
as 90 o in midas Gen.

To consider constructability, the program rounds off the required spacing to the lower 10 mm value.

42
 CHAPTE R 2. RC Design Algorithm

4.2 Detailing Rules for column design

4.2.1 Longitudinal Reinforcement
EN 1992-1-1:2004 specifies that l ongitudinal bars should have a diameter of not less than min.
Varying values of min are specified in National Annexes. EN1992-1-1:2004
9.5.2(1)
This needs to be taken care by the user. When specifying the design criteria for rebars in Design >
Concrete Design Parameter > Design Criteria for Rebars, the bars bigger than min in diameter
should be chosen by the user.

The minimum allowed amount of longitudinal reinforcement for a column is specified as greater
of the two values.
i. As,min = 0.10 NEd/fyd EN1992-1-1:2004
ii. 0.002 Ac 9.5.2(2)

The maximum value of amount of longitudinal reinforcement is specified as As,max. The EN1992-1-1:2004
recommended value of As,max is 0.04 Ac. 9.5.2(3)

The value of As,max can be viewed/modified in Limiting Maximum Rebar Ratio dialog box as shown
below:

Design > Concrete Design Parameters > Limiting Maximum Rebar Ratio

[Figure 4.1] Limiting Maximum Rebar Ratio dialog box

4.2.2 Shear Reinforcement

For column members, the diameter of the transverse reinforcement should not be less than, greater
of the two below: EN1992-1-1:2004
i. 6 mm 9.5.3(1)
ii. times the maximum diameter of the longitudinal bars
This needs to be taken care by the user. When specifying the design criteria for rebars in Design >
Concrete Design Parameter > Design Criteria for Rebars, the suitable bar diameter should be
chosen.

In case the shear reinforcement is not required, the minimum reinforcement is provided as:
w,min = 0.08 / (4.6)
s = Asw / w. bw . sin (4.7)
The s is calculated and used for maximum spacing.

The spacing of the transverse reinforcement along the column should not exceed s cl,tmax:
The recommended value is the least of the following three distances:
i. 20 times the minimum diameter of the longitudinal bars
ii. Lesser dimension of the column
iii. 400 mm
This specification is taken care by the program itself.
To consider constructability, the program rounds off the required spacing to the lower 10 mm value.

43
 CHAPTE R 2. RC Design Algorithm

4.3 Detailing Rules for Wall design

4.3.1 Vertical Reinforcement EN1992-1-1:2004
9.6.2(1)
The maximum amount of the vertical reinforcement should be applied as:
Asv,max = 0.04 Ac (4.8)
The ratio can be viewed/edited in Limiting Maximum Rebar Ratio dialog box as shown in
previous section.
The minimum amount of vertical reinforcement should be applied as:
Asv,min = 0.002 Ac (4.9)
This is the recommended value and it cannot be edited by the user.

4.3.2 Horizontal Reinforcement EN1992-1-1:2004

The minimum horizontal reinforcement is provided as per the following specifications: 9.6.3(1)
w,min = max [0.25As,y/Ac, 0.001] (4.10)
The maximum spacing of the horizontal reinforcement shall be limited to minimum of the following: EN1992-1-1:2004
9.6.3(2)
I. 2*As,v/(w,min hw)
II. 400 mm

For wall design, the detailing rules for shear reinforcement are same as that of column design.

44
 CHAPTER 3

RC Design Tutorial
Eurocode2 Design Guide for midas Gen
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Eurocode Design of a Multi-story

RC Building
Part I EC2 in Gen
Part II Model & Design Parameters
Part III ULS Member Design
Part IV ULS Member Checks
Part V SLS Member Checks

1 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Eurocode Design of Reinforced Concrete Building

as per EN 1992-1-1: 2004
Overview
Eurocode Design of
Reinforced Concrete Building
Model
- 6-story Reinforced Concrete
Building
- Element: Wall, Beam
Load & Boundary Condition
- Self Weight
- Floor Loads
- Wind Loads
- Seismic Loads
- Supports
Analysis
- Linear Static Analysis

2 MIDAS Information Technology Co., Ltd.

1
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Reinforced Concrete Design Features in midas Gen

Gen provides automatic design for beam, column and shear wall.
Section checking with the given data.
Ultimate limit state and Serviceability limit state design and/or checking.
Default load combinations as per Eurocode 2.
Static wind loads as per Eurocode 1-4: 2005
Static seismic loads and response spectrum function as per Eurocode 8-1: 2004
Capacity design as per Eurocode 8-1 can be applied by checking on Apply EC8:04
Capacity Design option in Concrete Design Code dialog box.
Available Section shapes
Column: Rectangle, Circular, Hollow circular
Wall: Rectangle
Beam: Rectangle, T-shape
Note:
Torsion should be checked by the user.
For meshed slab and wall design, we can use Meshed Slab/Wall Design function.

3 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Ultimate Limit State (ULS) Design

(1) Bending without axial force

Assuming K and K have been determined:

where:

K M / bd 2 f ck
K 0.598 0.18 2 0.21
where:
1 0 = Moment Redistribution Ratio(Factor)

If K K (singly reinforced)

As1 M / f yd z

where:
As1is area of compression steel (in layer 1).
f yd f yk / s

z d [0.5 0.5(1 3.53 K ) 0.5 ] 0.95 d

4 MIDAS Information Technology Co., Ltd.

2
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

If K K (Doubly Reinforced)
As 2 ( M M ) / f sc ( d d 2 )
where:
As 2 is area of compression steel (in layer 2).

M K bd 2 f ck
f sc 700( xu d 2 ) / xu
f sc f yd

where:
d 2 is effective depth to compression steel.
xu ( 0.4)d
As1 M / f yd z As 2 f sc / f yd

For Minimum and Maximum Required Rebar Area

As ,min 0.26( f ctm / f yk )bt d 0.0013bt d

5 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

(2) Bending with axial force

Slenderness Ratio
Second order effects may be ignored if the slenderness is below a certain value lim.
l0 / i

lim 20 A B C / n

Design Bending moment

M Ed max[ M 0 Ed M 2 , M 02 , M 01 0.5 M 2 ]

where:
M Ed is design moment.
M 0 E d is equivalent first order moment including the effect of imperfection(at about mid
height) and may be taken as = M 0e.
where:
M 0 e (0.6 M 02 0.4 M 01 ) 0.4 M 02
M 02 , M 01 is first order end moments at ULS including allowances for imperfections. M 02 M 01

M 2 N Ed e2 ; nominal second order moment in slender column

6 MIDAS Information Technology Co., Ltd.

3
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Capacity - Axial force and uni-axial bending moment

The combinations of and that cause failure of a given column section are illustrated by an interact
ion diagram as shown below.

7 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Pure compression, point

Po f cd ( Ag Ast ) Ast f yd

Buckling failure is not considered.

Pure tension, point

Po Ast f yd
Balanced failure, point
The load and moment at balanced failure, Pb and M b, can be calculated by substituting f s f yd
and b into the above equations.
0.003Es
b d
f yd 0.003Es

Where, =0.8 for fck 50MPa

=0.8-(fck-50)/400 for 50 < fck 90MPa
=0.7 for fck > 90MPa

8 MIDAS Information Technology Co., Ltd.

4
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

For symmetrically reinforced members, the loads and moments at the points ~ may be calcul
ated by the formula below.
Pu f cd xb As' f s' As f s
h h h
M u f cd xb( 0.5 x) As' f s' ( d ' ) As f s ( d )
2 2 2

9 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

(3) Shear
Shear resistance of a member with shear reinforcement is equal to:
VRd VRd , s
In regions of the member where VEd VRd,c no calculated shear reinforcement is necessary.
In regions where VEd > VRd,c sufficient shear reinforcement should be provided in order that
VEd VRd.

Members not requiring design shear reinforcement

VRd ,c [CRd ,c k (100 1 f ck )1/ 3 k1 cp ]bw d

With a minimum of
VRd ,c (vmin k1 cp )bw d

Members requiring design shear reinforcement

The shear resistance, VRd is the smaller value of:
VRd ,s ( Asw / s ) zf ywd cot
and
VRd ,max cwbw z 1 f cd /(cot tan )

10 MIDAS Information Technology Co., Ltd.

5
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Serviceability Limit States (SLS) Design

(1) Stress Limitation
The compressive stress shall be limited to a value k1fck in order to avoid longitudinal cracks und
er the characteristic combination of loads. A value of K1 can be defined by the user and default v
alue is 0.6.

If the stress in the concrete under the quasi-permanent loads is less than k2fck, linear creep may b
e assumed. If the stress in concrete exceeds k2fck, non-linear creep should be considered. A valu
e of K2 can be defined by the user and default value is 0.45.

Unacceptable cracking or deformation may be assumed to be avoided if, under the characteris
tic combination of loads, the tensile stress in the reinforcement does not exceed k3fyk. A value of K
3 can be defined by the user and default value is 0.8.

Where the stress is caused by an imposed deformation, the tensile stress should not exceed k4fyk.
A value of K4 can be defined by the user and default value is 1.0.

11 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

(2) Crack Control

A limiting calculated crack width, wmax, taking into account the proposed function and nature of the
structure and the costs of limiting cracking, should be established.

(3) Deflection Control

The appearance and general utility of the structure could be impaired when the calculated sag of a be
am, slab or cantilever subjected to quasi-permanent loads exceeds span/250.
For the deflection subjected to characteristic loads can be checked by user defined limit. Default limi
t is Span/250.

12 MIDAS Information Technology Co., Ltd.

6
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Beam detailing
The following data are required to be input for Beam design:

Beam section size (b, h)

Cover to rebar center default minmaxh 10,63.5mm ,76.2mm
Bar size
Main rebar: Up to 5 sizes simultaneously selected, which GEN will use
to find the most appropriate.
Stirrup/Link: One size can be selected.
P5, P6, P7, P8, P9, P10, P11, P12, P13, P16, P20, P25, P32, and P40 are
available.
Arrangement (= Number of legs of the transverse or shear reinforcement)
Only one case can be selected among the numbers from 2 to 20.

13 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Beam detailing
The following conditions are applied to Beam design:

Maximum rebar ratio of main rebar, EN 1992-1-1 9.2.1.1

As , max 0.04 Ac
Minimum rebar ratio of main rebar, EN 1992-1-1 9.2.1.1
As , min max 0.26 f ctm f yk bt d ,0.0013bt d
Minimum spacing (= clear distance) of bars, EN 1992-1-1 8.2
max Dbar , d g 5mm,20mm
Maximum stirrup spacing, EN 1992-1-1 9.2.2

S max min Asw bw w, min ,0.75d 1 cot w, min 0.08 f ck f yk

14 MIDAS Information Technology Co., Ltd.

7
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Beam detailing
The following are the Design results provided by Gen:

Main rebar
Required rebar area satisfying minimum bar spacing
Number of bars at top and bottom satisfying minimum bar spacing
Capacity ratio at I-end, middle, and J-end of beam member
Up to two layers of rebar can be designed
Stirrups/Links
Required rebar area per unit length
Spacing of stirrups
Capacity ratio at I-end, middle, and J-end of beam member
Check for crushing of compression struts

15 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Column detailing
The following data are required to be input for Column design:

Column section size (b, h)

Cover to rebar center default minmaxh 10,63.5mm ,76.2mm
Bar size
Main rebar: Up to 5 sizes simultaneously selected, among which GEN
will find the most appropriate.
Tie/Spiral: One size can be selected.
P5, P6, P7, P8, P9, P10, P11, P12, P13, P16, P20, P25, P32, and P40 are
available.
Arrangement (= Number of legs of the transverse reinforcement)
Different number of legs can be applied in the y and z direction.

16 MIDAS Information Technology Co., Ltd.

8
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Column detailing
The following conditions are applied to Column design:

Maximum rebar ratio of main rebar, EN 1992-1-1 9.5.2

As , max 0.03 Ac , which can be modified.
Minimum rebar ratio of main rebar, EN 1992-1-1 9.5.2
As , min max 0.10 N ED f yd ,0.002 Ac
Minimum spacing (clear distance) of bars, EN 1992-1-1 8.2
max Dbar , d g 5mm,20mm
Maximum stirrup spacing, EN 1992-1-1 9.5.3 & 9.2.2
S cl , t max min 20 Dbar , b, h,400 mm, Asw bw w, min w, min 0.08 f ck f yk
The maximum spacing is reduced by a factor 0.6 at the i and j-end
of the column.

17 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Column detailing
The following are the design results provided by Gen:

Main rebar
Number of bars satisfying minimum bar spacing
Capacity ratio for the most critical part among I-end, middle, and J-end
of column member
Biaxial P-M interaction diagram
Note. Two layers of rebar or bundle bars are not applicable.
Stirrup/Links
Required rebar area per unit length
Spacing of ties/spirals
Capacity ratio for the most critical part of column member (I-end,
middle, and J-end)
Check for crushing of compression struts

18 MIDAS Information Technology Co., Ltd.

9
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Shear Wall detailing

The following data are required to be input for Shear Wall design:

Wall section size (L, h)

Cover to rebar center default 50.8mm
Bar size
Vertical rebar: Up to 5 sizes simultaneously selected, among which GEN
will find the most appropriate.
End rebar: One size can be selected, then program will find the most
appropriate, greater than or equal to the one selected.
Horizontal rebar: One size can be selected.
P5, P6, P7, P8, P9, P10, P11, P12, P13, P16, P20, P25, P32, and P40 are
available.
Spacing of vertical rebar
Select as many spacings as you want program to try
Spacing of horizontal rebar
Design method
19 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Shear Wall detailing

The following conditions are applied to Shear Wall design:

Maximum rebar ratio of vertical rebar, EN 1992-1-1 9.6.2

As , max 0.04 Ac , which can be modified.
Minimum rebar ratio of vertical rebar, EN 1992-1-1 9.6.2
As , min 0.002 Ac
Maximum spacing of horizontal rebars, EN 1992-1-1 9.6.3
S max min 2 As , v v , min h ,400 mm v , min max 0.25 As , v Ac ,0.001

20 MIDAS Information Technology Co., Ltd.

10
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Shear Wall detailing

Followings are the design results provided by Gen:

Vertical rebar
Spacing of vertical rebar
Capacity ratio for the most critical part among top and bottom of wall
Uniaxial P-M interaction diagram
Horizontal
Required rebar area per unit length
Spacing of horizontal rebar
Capacity ratio for the most critical part among top and bottom of wall
Check for crushing of compression struts

21 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

PART II - Contents

The Model File

Performing the Analysis
Design Parameters
ULS Design

22 MIDAS Information Technology Co., Ltd.

11
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Typical Floor Plan

9000 mm 9000 mm 9000 mm 9000 mm

5100 mm 5100 mm
7200 mm
5100 mm 5100 mm

23 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Typical Sectional Elevation

4000 mm 4000 mm 4000 mm
4500 nm
4500 nm
5000 mm

24 MIDAS Information Technology Co., Ltd.

12
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Opening the Pre-generated Model File

1. File > Open Project

2. Select EC2 Design.
2 3. Click [Open] button.

This tutorial is intended to illustrate

design procedure as per Eurocode2.
Therefore, the geometry creation, boundary
assignment, load application will be skipped.
For the aforementioned, refer to Seismic
3 Design for RC Building tutorial.

In this tutorial, slab is not included in the

model and considered as a rigid diaphragm.

Analysis

1. Analysis > Perform Analysis

25 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Parameters for ULS Design

Load Combinations
Design Code
Sway Frame Definitions
Member Assignment
Live Load Reduction Factor Modifications
Unbraced Lengths (L, Lb)
Partial Safety Factors
Concrete and Rebar Properties

26 MIDAS Information Technology Co., Ltd.

13
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Load Combinations
1. Results > Combinations 4
2. Click on Concrete Design tab.
5
3. Click [Auto Generation] button. 6
4. Option: Add
5. Code Selection: Concrete
6. Design Code: Eurocode2:04 5

7. Click [OK] Button.

8. Click [Close] Button.

The program
automatically creates
design load
combinations which
can be also modified or
deleted by the user.
3
8 7

27 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Design Code

2 1. Design > Concrete Design Parameter > Design

Code
2. Design Code: Eurocode2:04
3. Click [OK] button.

Sway Frame Definitions

1. Design > General Design Parameter >
Definition of Frame

2
2. X-Direction of Frame: Braced | Non-sway
3. Y-Direction of Frame: Braced | Non-sway
3 4. Design Type: 3-D

4 5. Check off Auto Calculate Effective Length

Factors.
6. Click [OK] button.
5
In the non-sway frame, applying 1 for the
6 effective length factor will give conservative
results.

28 MIDAS Information Technology Co., Ltd.

14
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Member Assignment
1. Design > General Design Parameter >
Member Assignment
2. Assign Type: Automatic
3. Selection Type: All
4. Click [Apply] button.
2 5. Click [Close] button.

A single Member can be

assigned when the member
is consisted of a number of
beam elements.
4

29 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Live Load Reduction Factors (1)

1. Design > General Design
Parameter > Modify Live Load
Reduction Factor

2 2. Option: Add/Replace
1 3. Reduction Factor: 0.82
3
4. Applied Components: All Forces
4 5. View > Select > Identity
6. Select Type: Story
7. Select 1F
10 8. Click [Add] button.
9. Click [Close] button.
10. Click [Apply] button.

1. Reduction factor for 1st floor

columns and walls.
2 n 2 0
6 8 n 0.82
7
n
n5 0 0.7
EN 1991-1-1 6.3.1.2 (11)
9

30 MIDAS Information Technology Co., Ltd.

15
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Live Load Reduction Factors (2)

1. Design > General Design
Parameter > Modify Live Load
Reduction Factor
2. Option: Add/Replace
2
1 3. Reduction Factor: 0.85
3 4. Applied Components: All Forces

4 5. View > Select > Identity

6. Select Type: Story
7. Select 2F.
8. Click [Add] button.
12
9. Select Floor.
10. Click [Delete] button.
11. Click [Close] button.
12. Click [Apply] button.

6 8 1. Reduction factor for 2nd floor

columns and walls.
7 10
2 n 2 0
n 0.85
n
9
n4 0 0.7
11

31 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Live Load Reduction Factors (3)

1. Design > General Design
Parameter > Modify Live Load
Reduction Factor
2. Option: Add/Replace
2
1 3. Reduction Factor: 0.9
3 4. Applied Components: All Forces

4 5. View > Select > Identity

6. Select Type: Story
7. Select 3F.
8. Click [Add] button.
12
9. Select Floor.
10. Click [Delete] button.
11. Click [Close] button.
12. Click [Apply] button.

6 8 1. Reduction factor for 3rd floor

columns and walls.
10
7 2 n 2 0
n 0.9
n
9
n3 0 0.7
11

32 MIDAS Information Technology Co., Ltd.

16
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Unbraced Lengths (L, Lb)

1. Design > General Design Parameter > Unbraced 1. If 0 is entered for Ly and Lz,
Length(L, Lb) unbraced lengths will be calculated by the
program based on the nodal coordinates of
2. Option: Add/Replace the beam elements.
3. Unbraced Length Ly: 0 mm
1
4. Lz: 0 mm
5. Laterally Unbraced Length: Check on Do not consider.
6. View > Select > Select All
7. Click [Apply] button.

3, 4

33 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Partial Safety Factors

1. Design > Concrete Design Parameter > Partial

Safety Factors for Material Properties
2
2. Click [Update By Code] button.
3. Click [OK] button.

34 MIDAS Information Technology Co., Ltd.

17
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Concrete and Rebar Properties

1. Design > Concrete Design Parameter > Modify

Concrete Materials
2. Select C30/37 from Material List.
2
3. Rebar Selection Code: EN04(RC)
4. Grade of Main Rebar: Class B
5. Grade of Sub-Rebar: Class A
6. Click [Modify] button.
7. Click [Close] button.

4, 5

6 7

35 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Design Criteria for Rebar (1)

1. Tools > Preferences

2. Click on Design.
3. Concrete Design Code: Eurocode2:04
4. Rebar Material Code: EN04(RC)
5. Click [OK] button.

36 MIDAS Information Technology Co., Ltd.

18
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Design Criteria for Rebar (2) Beam Design

6. Design > Concrete Design Parameter > Design Criteria
for Rebar
7
7. For Beam Design Main Rebar: click [Rebar] button.
10 11
8. Select P20 and P25.
12
9. Click [OK] button.
13 10. Stirrups: P10, Side Bar: P12
11. Arrangement: 2
12. dT: 55 mm, dB: 55 mm
13. Option of Spliced Bars: None

37 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Design Criteria for Rebar (3) Column Design

14. For Column Design Main Rebar: click
[Rebar] button.
15. Select P25 and P32.
16. Click [OK] button.
17. Ties/Spirals: P10
18. Arrangement: X: 2, Z: 2
19. do: 55mm
14
17 20. Option of Spliced Bars: None
19 18

20

15

16

38 MIDAS Information Technology Co., Ltd.

19
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Design Criteria for Rebar (4) Wall Design

21. For Shear Wall Design Vertical Rebar: click
[Rebar] button.
22. Select P13 and Click [OK] button.
23. Horizontal Rebar: P13, End Rebar From: P10
24. de: 45 mm, dw: 45 mm
25. Click [Input Additional Wall Data] button.
26. End Rebar Design Method: Method-1
27. Click [OK] button.
28. Click [OK] button.

26

21
23

24
25

28 27

39 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

ULS Design

Concrete Beam Design

1 Section for Design
Concrete Column Design
Concrete Wall Design

1. The Section for Design function provides Member

design of concrete sections based on the section data defined
by the user. It allows you to find the appropriate section
without re-analysis.

40 MIDAS Information Technology Co., Ltd.

20
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Concrete Beam Design (1) 1. Design > Concrete Code Design > Beam Design
2. Sorted by: Member
3. Click to expand the dialog box.
4. SEL: select MEMB 1.

6 7
5 3

41 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Concrete Beam Design (2)

5. Click [Graphic] button.

42 MIDAS Information Technology Co., Ltd.

21
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Concrete Beam Design (3)

6. Click [Detail] button.

43 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Concrete Beam Design (4)

7. Click [Summary] button.

44 MIDAS Information Technology Co., Ltd.

22
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Section for Design (1)

1. Design > Concrete Code Design > Beam Design
2. Sorted by: Property

1. Red N means that negative moment is larger than the

resistance for the given section .
Red P means that the positive moment is larger than the
1 resistance for the given section.

45 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Section for Design (2) 3. Design > Section for Design

4. Select 413 G3 section.

5
5. Click [Modify] button.
6. Change H from 0.8m to 0.85m and Change B from
0.6m to 0.65m.
4 7. Click [OK] button.
8
8. Click [Close] button.

46 MIDAS Information Technology Co., Ltd.

23
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Section for Design (3)

9. SEL: select SECT 413.

10. Click [Re-calculation] button.

1. Check results of Section

413 G1 change to OK.

1
9

10

47 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Concrete Column Design (1) 1. Design > Concrete Code Design > Column Design
2. Sorted by: Member
3. Click to expand the dialog box.
4. SEL: select MEMB 41.

1. As with Beam we may check [Graphic], [Detail] &

3 [Summary] results.
1
5

48 MIDAS Information Technology Co., Ltd.

24
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Concrete Column Design (2)

5. Click [Draw PM Curve] button.
6. Click [Close] button.

49 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Concrete Wall Design (1)

1. Design > Concrete Code Design > Wall Design
2. Sorted by: Wall ID + story
3. Click to expand the dialog box.
4. SEL: select WID 1 Story 1F.

1. As with Beam we may check [Detail] &

5 1 [Summary] results.
3
2 2. As with Column we may Draw PM Curve.

50 MIDAS Information Technology Co., Ltd.

25
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Concrete Wall Design (2)

5. Click [Graphic] button.

51 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Manually Entering Rebar and ULS Checking

Enter Rebar Data using Design > Concrete Design Parameter > Modify
Beam/Column/Wall Rebar Data or Design > Concrete Code
1 Design > Beam/Column/Wall Design > [Update Rebar] button

1. In this tutorial, Modify Beam Rebar Data will only be illustrated. In the same manner, Column and Wall
Section Data can also be defined.
1. Rebar will be MANUALLY entered using Design > Concrete Design Parameter > Modify
Beam/Column/Wall Rebar Data
1. Rebar can be AUTOMATICALLY entered using Design > Concrete Code Design > Beam/Column/Wall
Design > [Update Rebar] button (this is illustrated later).

52 MIDAS Information Technology Co., Ltd.

26
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Modify Beam Section Data (1)

1. Design > Concrete Design Parameter > Modify Beam Rebar
Data

2 2. SECT: check on ID 412.

3.Uncheck Same Main Rebar Size at Top and Bottom and
Same Main Rebar Size At I,M and J .
4. For Main Rebar at End(I)
5. For Top Rebar: in front of Top and 1 : 4 P25
6. Bottom Rebar: In front of Bot and 1 :2 P20
7. For Main Rebar at Center
5 8
11 8. For Top Rebar: in front of Top and 1 : 2 P20
9. Bottom Rebar: In front of Bot and 1 :4 P25

6 10.For Main Rebar at Center

12
11.For Top Rebar: in front of Top and 1 : 4 P25

9 12. Bottom Rebar: In front of Bot and 1 :2 P20

53 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Modify Beam Section Data (2)

13. Stirrup in End(I)
14. Arrangement: 2
15. Stirrups Space: 100 mm
16. Stirrup in Center
17. Arrangement: 2
18. Stirrups Space: 200 mm
19. Stirrup in End(J)
20. Arrangement: 2
21. Stirrups Space: 100 mm
22.Stirrup: P10

14 15 17 18 20 21 23. dT, dB : 0.055m,0.055m

22
24. Click [Add/Replace] Button

23

54 MIDAS Information Technology Co., Ltd.

27
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

ULS Beam Member Code Check

1 6-1. Beam Code Checking

1. In this tutorial, only Beam Code Checking will be

illustrated. In the same manner, Column/Wall Code
Checking can be performed.

55 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

1. Design > Concrete Code Check > Beam Checking

Beam Code Checking (1)
2. Sorted by: Member
3. Results: Strength
4. Click to expand the dialog box.
5. SEL: MEMB 11

2
3

8 9
6 4

56 MIDAS Information Technology Co., Ltd.

28
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Beam Code Checking (2)

6. Click [Graphic] button.

57 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Beam Code Checking (3)

7. Option for Detail Print Position: check on End I. Mid. End J..
8. Click [Detail] button

58 MIDAS Information Technology Co., Ltd.

29
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Beam Code Checking (4)

9. Click [Summary] button.

59 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Parameters for SLS Checking

Concrete long-term and short-term Modulus of elasticity

Serviceability Load Combination
Enter Rebar Data using Design > Concrete Design Parameter > Modify
Beam Rebar Data or Design > Concrete Code Design > Beam
1 Design > [Update Rebar] button
Serviceability Limit Control Parameters

1. For serviceability check, entering rebar data is required.

60 MIDAS Information Technology Co., Ltd.

30
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Short/Long Term Elasticity Ratio

1. Design > Concrete Design Parameter > Modify

Concrete Materials
2. Select C30/37 from Material List.
2
3. Click button.
4. Click [OK] button.
5. Click [Close] button.

5 4

61 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Serviceability Load Combination Type

1. Design > General Design Parameter >

Serviceability Load Combination Type
2. Click [OK] button.

Once the load combinations are generated using

Auto Generation as per Eurocode2 as in Step 3-1,
the program automatically assigns the Quasi-
permanent, Frequent and Characteristic load
combinations.

62 MIDAS Information Technology Co., Ltd.

31
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Automatic Rebar Input

1. Design > Concrete Code Design > Beam Design

2. SEL: click [Select All] button.
1 3. Click [Update Rebar] button.
4. Click [Close] button.

1. By clicking [Update Rebar] button, the rebars

designed in this dialog box will be automatically
entered into the selected sections.

3
4

63 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

View Rebar Data on Section

1 1. Design > Concrete Design Parameter > Modify

2 Beam Rebar Data
2 2. SEL: check on ID 413.
3. Click [Close] button.

1. In this page, check the Rebar Data entered

using [Update Rebar] in the previous page.
2. In signifies that Rebar are placed.
3. The entered Rebar Data are displayed.
3

64 MIDAS Information Technology Co., Ltd.

32
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Enter Serviceability Limit Control Parameters

1. Design > Concrete Design Parameter >
Serviceability Parameters
2. Option: Add/Replace 2
3. Selection Type: By Selection
3
4. Exposure Class: XD1 11 13
5. Stress Parameters- k1: 0.6, k2: 0.45, k3: 0.8, k4: 1 4
12
6. Quasi-permanent Limit: 0.3 mm
7. Quasi-permanent Deflection Ctrl: L/250 5

8. Characteristic Deflection Control Limit: L/250

9. Deflection Amplification Factor: 1 14

10. View > Select > Identity

11. Select Type: Section
12. Select 411: G1, 412: G2, 413: G3, 414: 6
G4, 415: B1, 421: WG1, 422: WG2
13. Click [Add] Button.
7
14. Click [Close] Button.
15. Click [Apply] Button.
8

9
15

65 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

SLS Checks

1 Serviceability Checking for Concrete Beam

1. Serviceability check is provided for Beam members for the following limit states.
- Stress limitation
- Crack control
- Deflection control

66 MIDAS Information Technology Co., Ltd.

33
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Serviceability Checking (1) 1. Design > Concrete Code Check > Beam Checking
2. Sorted by: Member
3. Results: Serviceability
4. Click to expand the dialog box.
5. SEL: select MEMB 1

2
3

7 8
6 4

67 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Serviceability Checking (2)

6. Click [Graphic] button.

68 MIDAS Information Technology Co., Ltd.

34
 CHAPTER 3. RC Design Tutorial

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Serviceability Checking (3)

7. Click [Detail] button.

69 MIDAS Information Technology Co., Ltd.

midas Gen Tutorial Eurocode Design of Multi-story

Fundamentals
RC Building

Serviceability Checking (4)

8. Click [Summary] button.

70 MIDAS Information Technology Co., Ltd.

35