Test Block ERMLG

identified by a number which corresponds with the

Applications terminations on the ERMLG.

ERMLG Test block provides facilities for monitoring & secondary It is recommended that the protection scheme or relay is wired
injection testing of any power system protection scheme, when to the even numbers of the test modules. To ensure the scheme
used with the multi fingered test plug type ERMLB01. wiring is routed logically it is recommended that the ERMLG is
always positioned on the right-hand side of the relay, when
viewed from the front. The connections to other equipment
Description such as CTs, VTs, and dc supplies should be made to the odd
numbered terminals indicated on the ERMLG. This will ensure
ERMLG Test block removes the need to disturb protective system
that on connection of the ERMLB, the sockets on the even
wiring for testing.
numbered side of the test plug are the isolated relay circuits
The ERMLG Test Block is housed within an Epsilon enclosure. and the sockets on the odd numbered side are connected to the
potentially live supplies and shown in Figure 3.
The ERMLG Test Block has 14 pairs of spring loaded contacts
which are linked to a terminal block positioned at the rear of the
enclosure.

Each pair of contacts are normally closed completing the circuit

through the test block when the associated protection equipment
is in use.

For testing purposes the test block can be assessed by removing

the front cover. The ERMLG 01 has a metallic probe attached to
the front cover assembly which when withdrawn open circuits the ERMLG
2 contacts at position 13 and 14.

The main dc auxiliary supply to the protection scheme or relay can

be wired to this circuit to prevent inadvertent tripping of the
protection circuit after removal of the cover and during the test
procedure. TYPE-ERMLG
SAMPLE RELAY
SL.NO.ERMLG/01

The short test finger in position 13-14 on the ERMLB 01 will open
contacts 13-14 in the test block after the other fingers have made
contact in all other positions. !
When the cover is removed a blue fascia is revealed which is
attached to the test block. This gives a visual indication and
warning that the protection scheme or relay is not in service.

The insertion of the ERMLB 01 test plug into the ERMLG

assembly (as shown in figs. 1 and 2) open circuits the contact
pairs. The ERMLB 01 has 28 test points each position being
Figure 1: Test Block ERMLG
Note:
Mechanical Specification
It is important that the sockets in the plug (ERMLB 01)which
correspond to the current transformers secondary windings are The ERMLG is a size E2 unit in the Epsilon range of
linked prior to the plug being inserted into the test block. enclosures.The overall dimensions and panel fixing details are
shown in Figure 4.
This will ensure that the current transformers secondary
windings are short circuited prior to disconnection from the The rear terminal block has 28 terminals each with an M4 screw
protection scheme or relay (as shown in Figure 3). outlet for the attachment of external wiring, fitted with 'L'
shaped pre-insulated ring tongue terminations.
Terminals 13 & 14 on ERMLG 01 must not be used for CT
connections since this will present a safety hazard. The reason
for this that the associated ERMLB 01 test plug contact finger ERMLB 01 Multi-fingered test
is shorter than the others.
plugs
If the dc auxiliary supply is to be used during testing it can be
linked using the sockets in the test plug. The ERMLB 01 is inserted into the ERMLG test block and is
securely retained by means of two knurled screws. The
Operation of the contacts can be monitored by connecting the ERMLB01 test plug incorporate 28 test sockets, each socket
test equipment to the protection scheme or relay with the even accepting a 4mm diameter plug.
numbered sockets of the test plug.
The following are supplied with each ERMLB01 test plug:
If a number of ERMLG test blocks are connected to relay it is
recommended that the dc supply be routed through each 1.4 short plug links. Each comprised of 50mm of
ofthem to safeguard against inadvertent operation. identified interconnecting cable with a 4mm plug each end.
by a number which corresponds with the terminations on the
2.4 long plug links. Each comprised of 150mm of
ERMLG.
interconnecting cable with a 4mm plug each end.

3.6 spare 4mm plugs. These accept up to 2.5sq. mm flexible

insulated cable for test lead purposes.

Precautions
BEFORE inserting a Test Plug into a Test Socket carrying
current transformers secondary circuits. ENSURE that the Test
Plugs corresponding to the current transformers circuits are
short-circuited.

This is to ensure the current transformer secondary circuit are

not inadvertently open-circuited during insertion of the last
plug.

BEFORE inserting a Test Plug to measure current ENSURE that

the ammeter is on the correct range and that it is connected to
test leads.

Figure 2: Test Block ERMLG

 Current withstand
Connections
ERMLG 01 All contact circuit rated at 20A
The connections will depend upon the scheme and details must be continuously or 400A for 1s, ac or dc
obtained from the appropriate diagrams. If it is necessary to use the
d.c. auxiliary supply during testing, then a test link may be fitted ERMLB 01 10A continuously or 165A for 1s
across the sockets in the Test Plug.
Atmospheric environment

Technical Data Temperature

IEC 255-6: Storage and transit - 25C to +70C
Operating - 25C to +55C
High Voltage withstand
IEC 68-2-1: Cold
Insulation IEC 255-5
IEC68-2-2: Dry Heat
ERMLG 5kV rms for 1 minute between all case
Humidity
terminals connected together and the case
earth terminals. IEC 68-2-3: 93% RH and + 40C

5kV rms for 1 minute between any contact Enclosure Protection

pair and either adjacent alternate contact pair, IEC 529: IP50 (dust protected)
provided the intermediate contact pair is not
Mechanical environment
used.
Vibration
2kV rms for 1 minute between any contact
IEC 255-21-1: Class2
pair and either adjacent contact pair.
Qualification
1kV rms for 1 minute between terminals 13
and 14 when the cover is removed (e.g. ISO9001-2008
opening the auxiliary supply or trip circuit).

ERMLB 01 As ERMLG 01 plus 2kV rms for 1 minute

between incoming and outgoing contacts when
inserted.

TYPICAL APPLICATION OF THE ERMLG01 TEST SOCKET AND ERMLB01 TEST PLUG

Figure 3
 OUTLINE AND DRILLING FOR ERMLG TEST SOCKET IN EPSILON E2 CASE

Figure 4

The policy of EASUN REYROLLE is one of continuous improvement and development. The company therefore reserves the right to supply equipment which may differ slightly
from that described and illustrated in the publication.

ERL Group Corporate Office

#389, Rasukumaki, Hulimavu, Begur Hobli, Bannerghatta Road, Bangalore 560 076, India
Tel: +91 80 6717 7000 Fax: +91 80 6717 7002 Email: [email protected]

Global Marketing Offices

Germany, Canada, Hong Kong, Thailand, South Africa, UAE, Brazil, Peru & USA

FACT/ERMLG/10-10/REV1.0
Global Manufacturing Centers
India, Canada & Germany

Global Technology Centers

India, Canada & Germany

Marketing Offices in India

Bangalore Chennai Kolkata
Tel: +91 80 6717 7000/01 Bhopal Tel: +91 44 2434 6425/7608 Tel: +91 33 2284 8320
Fax: +91 80 6717 7002 Fax: +91 755 2684221 Fax: +91 44 2434 6435 Fax: +91 33 2284 8326
Email: [email protected] Email: [email protected] Email: [email protected] Email: [email protected]

Mumbai Noida
Tel: +91 22 2285 54415/ 2202 2270 Tel: +91 120 2405 741/42/43
Fax: +91 22 2285 5703
Email: [email protected]
Fax: +91 120 2405 744
Email: [email protected]
Secunderabad
Tel: +91 40 2781 7847
Email: [email protected] ERL
www.easunreyrolle.com