IMI CORNELIUS INC g One Cornelius Place g Anoka, MN 55303-6234

Telephone (800) 238-3600 Facsimile (612) 422-3246

Service Manual
SELF-CONTAINED FLAKED ICE MAKER
Model: Series 200, 525, 725
(R404A Refrigerant)

IMPORTANT:
TO THE INSTALLER.
It is the responsibility of
the Installer to ensure that
the water supply to the
dispensing equipment is
provided with protection
against backflow by an air
gap as defined in
ANSI/ASME A112.1.2-1979;
or an approved vacuum
breaker or other such
method as proved effective
by test.

Water pipe connections

and fixtures directly Distributed By:
connected to a potable Commercial Refrigeration Service, Inc.
water supply shall be WWW.WorldRestaurantSupply.COM
sized, installed, and
maintained according to toll free (866) Ice Maker
Federal, State, and Local (623) 869-8881
Codes.

Part No. 166240010

November, 1993
Revised: October, 1996

THIS DOCUMENT CONTAINS IMPORTANT INFORMATION

This Manual must be read and understood before installing or operating this equipment

IMI CORNELIUS INC; 199396 PRINTED IN U.S.A

 TABLE OF CONTENTS
Page
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SPECIFICATIONS 200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SPECIFICATIONS 525 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SPECIFICATIONS 725 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADJUSTMENT PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TYPICAL WATER CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TYPICAL REFRIGERANT CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
ELECTRICAL CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
CIRCUIT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ONOFF SWITCH/CIRCUIT BREAKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
BIN THERMOSTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
HIGH PRESSURE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
GEARMOTOR START RELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
POWER RELAY/CONTACTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
FAN CYCLING SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
DELAY THERMOSTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
COMPRESSOR START RELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
POTENTIAL RELAYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CAPACITORS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SANITIZING AND CLEANING PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
WATER TREATMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
WINTER STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CLEANING THE CONDENSER (AIR COOLED) . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
SERVICE ANALYSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
UNIT WILL NOT RUN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
COMPRESSOR CYCLES INTERMITTENTLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MAKING WET ICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
UNIT RUNS BUT MAKES NO ICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
WATER LEAKS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
EXCESSIVE NOISE OR CHATTERING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
MACHINE RUNS WITH FULL BIN OF ICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
UNIT OFF ON RESET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
UNIT GOES OFF ON RESET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
UNIT GOES OFF ON RESET. (CONTD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
ILLUSTRATED PARTS BREAKDOWN, SERIES 525725 . . . . . . . . . . . . . . . . . . . . . . 21
PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
CABINET PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

i 166240010
 TABLE OF CONTENTS (contd)

LIST OF FIGURES
Page
FIGURE 1. 200 SERIES SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FIGURE 2. 525 SERIES SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FIGURE 3. 725 SERIES SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
FIGURE 4. WATER LEVEL ADJUSTMENT PROCEDURE . . . . . . . . . . . . . . . . . . 6
FIGURE 5. TYPICAL WATER CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
FIGURE 6. TYPICAL REFRIGERANT CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
FIGURE 7. WIRING DIAGRAM AF 200P-SC-R 115 VOLTS 60 HZ . . . . . . . . . 14
FIGURE 8. WIRING DIAGRAM AF-200-P-SC-50-R 220 VOLTS 50 HZ . . . . . . . 15
FIGURE 9. WIRING DIAGRAM AF525SC-R AND AF725-SC-R
115 VOLTS 60 HZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
FIGURE 10. WIRING DIAGRAM AF/WF-525PSC-50-R 220 VOLTS 50 HZ . . . . 17
FIGURE 11. PARTS BREAKDOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
FIGURE 12. CABINET PARTS BREAKDOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

LIST OF TABLES
AF-200-P(S)-SCR PRODUCTION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
AF-200-P-SC50R PRODUCTION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
AF-525-P(S)-SCR PRODUCTION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
AF-525-P-SC50R PRODUCTION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
AF-725-P-SCR PRODUCTION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

166240010
ii
 INTRODUCTION

We have strived to produce a quality product. The design has been kept simple thus insuring troublefree op-
eration.

This manual has been prepared to assist servicemen and users with information concerning installation,
construction and maintenance of the ice making equipment. The problems of the serviceman and user have
been given special attention in the development and engineering of our ice makers.

If you encounter a problem which is not covered in this manual, please feel free to write or call. We will be
happy to assist you in any way we can.

When writing, please state the model and serial number of the machine.

Address all correspondence to:

A Product of IMI Cornelius Inc.

One Cornelius Place
Anoka, MN 553036234

Phone 8005543526
FAX 6124223232
PRINTED IN USA

1 166240010
 SPECIFICATIONS 200

26 1/2-IN. 13 1/2-IN.
67-CM 34-CM

4-IN.
10-CM
7-IN.
18-CM

ON-OFF
SWITCH REAR VIEW
OF CABINET
5-IN. 3/4-IN. ELECTRICAL
34-IN.
13-CM 2-CM BOX AREA
86-CM
A
40-IN. 26-IN. B
102-CM 66-CM 19-IN. C
48-CM
24 7/8-IN.
AIR 63-CM
FLOW
25-IN. 7-IN.
64-CM 18-CM
6-IN.
15-CM A- 1/4 WATER INLETS
(S.A.E. MALE FLARE)
B- 5/8 O.D. TUBE (DRAIN)
C- 1/2 O.D. TUBE (DRAIN)

FIGURE 1. 200 SERIES SPECIFICATIONS

ICE PRODUCTION CAPACITY (approximate)

AF-200-P(S)-SCR PRODUCTION CHART

AIR TEMPERATURE WATER TEMPERATURE
50 F/10 C 70 F/21 C 80 F/27C

50
F/10
C 219 lbs/99 kgs 188 lbs/85 kgs 175 lbs/79 kgs

70
F/21
C 208 lbs/95 kgs 174 lbs/79 kgs 166 lbs/75 kgs
90
F/27
C 161 lbs/35 kgs 130 lbs/59 kgs 117 lbs/53 kgs

AF-200-P-SC50R PRODUCTION CHART

AIR TEMPERATURE WATER TEMPERATURE
50 F/10C 70 F/21 C 80 F/27 C

50
F/10
C 234 lbs/106 kgs 206 lbs/94 kgs 197 lbs/90 kgs

70
F/21
C 213 lbs/97 kgs 190 lbs/86 kgs 180 lbs/82 kgs
90
F/27
C 183 lbs/83 kgs 164 lbs/75 kgs 156 lbs/71 kgs

200
Compressor Model Copeland JS25CIE-IAA-203 (115V 60HZ)
Copeland AS13CIE-1AZ-908 (220V 50HZ)
Condenser Air Cooled
Refrigerant Charge 8 oz. R-404a (115V 60HZ)
7 oz. R-404a (220V 50HZ)
Refrigerant Control (115V 60HZ) Automatic Expansion Valve (28-PSI)
Refrigerant Control (220V 50HZ) Automatic Expansion Valve (31-PSI)
Inlet Water Supply 1/4 SAE male flare
Voltage 115V 60HZ or 220V 50HZ
Gearmotor Electrical Rating 1/8 hp
Gearmotor Amp. Rating 2 amps (115V 60 HZ)
1 amp (220V 50HZ)
Total Amp. Draw 11.0 Amps (115V 60HZ)
4.0 Amps (220V 50HZ)
Maximum Fuse Size 15 Amp (115V 60HZ)
15 Amp (220V 50HZ)
166240010 2
 SPECIFICATIONS 525
13 1/2-IN.
26 1/2-IN. 34-CM 3 1/2-IN.
67-CM 2-IN. 9-CM
5-CM 3 1/2-IN.
9-CM
2 1/2-IN.
6-CM

REAR VIEW
ELECTRICAL
5/8-IN. OF CABINET
ON-OFF BOX AREA
34-IN. 2-CM
SWITCH
86-CM 5 5/8-IN. A
26-IN. 14-CM B
19 1/2-IN. 3 5/8-IN.
66-CM 50-CM 9-CM
D
40-IN. C
102-CM E
MIN. AIR IN
24 3/4-IN.
63-CM 4 5/8-IN. 3 3/4-IN.
38 3/4-IN. 12-CM 10-CM
97-CM
26 3/8-IN.
6-IN. 14-IN. 67-CM
15-CM 36-CM
3 3/8-IN.
MIN.
9-CM

A- 3/8 WATER INLET (S.A.E. MALE FLARE)

B- 1/2 O.D. TUBE (CONDENSATE DRAIN)
C- 3/4 N.P.T. BIN DRAIN
D- CONDENSER WATER IN (W/C ONLY)
E- CONDENSER WATER OUT (W/C ONLY)

FIGURE 2. 525 SERIES SPECIFICATIONS

ICE PRODUCTION CAPACITY (approximate)

AF-525-P(S)-SCR PRODUCTION CHART

AIR TEMPERATURE WATER TEMPERATURE
50 F/10C 70 F/21C 80 F/27C

50
F/10
C 654 lbs/297 kgs 588 lbs/267 kgs 552 lbs/251 kgs

70
F/21
C 639 lbs/290 kgs 563 lbs/256 kgs 521 lbs/237 kgs
90
F/27
C 562 lbs/255 kgs 479 lbs/218 kgs 448 lbs/204 kgs

AF-525-P-SC50R PRODUCTION CHART
AIR TEMPERATURE WATER TEMPERATURE

50 F/10C 70 F/21C 80 F/27C

50
F/10
C 629 lbs/286 kgs 528 lbs/240 kgs 494 lbs/225 kgs

70
F/21
C 621 lbs/282 kgs 525 lbs/239 kgs 489 lbs/222 kgs
90
F/27
C 493 lbs/224 kgs 414 lbs/188 kgs 387 lbs/176 kgs

525
Compressor Model Copeland RS43CIE-IAA-214 (115V 60HZ)
Copeland RS43CIE-IAZ-214 (220V 50HZ)
Condenser Air Cooled
Refrigerant Charge 17 oz. R404a
Refrigerant Control Automatic Expansion Valve (34-PSI)
Inlet Water Supply 3/8 SAE Male Flare
Voltage 115V 60HZ or 220V 50HZ
Total Amp Draw 15.5 Amps (115V 60HZ)
6.0 Amps (220V 50HZ)
Gearmotor Amp Draw 2 Amps (115V 60HZ)
1 Amp (220V 50HZ)
Gearmotor Electrical Rating 1/8 hp
Maximum Fuse Size 20 Amp (115V 60HZ)
15 Amp (220V 50HZ)
3 166240010
 SPECIFICATIONS 725

30-IN. 17 1/8-IN.
76-CM 43-CM
2 3/8-IN.
2-IN. 6-CM
5-CM
2 3/4-IN.
2 1/2-IN. 7-CM
6-CM

ON-OFF
SWITCH REAR VIEW
ELECTRICAL
OF CABINET
34-IN. BOX AREA 5/8-IN.
86-CM 2-CM
5 5/8-IN. A
26-IN.
40-IN. 66-CM 19 1/2-IN. 14-CM B
102-CM 50-CM
MIN. D
AIR IN C
E
28 3/8-IN.
48-IN. 72-CM
4 1/2-IN. 5 1/32-IN.
122-CM
11-CM 13-CM
16 3/8-IN. 32 1/16-IN.
6-IN. 42-CM 3 1/4-IN. 4-IN.
15-CM 81-CM
8-CM 10-CM

A- 3/8 WATER INLET (S.A.E. MALE FLARE)

B- 1/2 O.D. TUBE (CONDENSATE DRAIN)
C- 3/4 N.P.T. BIN DRAIN
D- CONDENSER WATER IN (W/C ONLY)
E- CONDENSER WATER OUT (W/C ONLY)

FIGURE 3. 725 SERIES SPECIFICATIONS

ICE PRODUCTION CAPACITY (approximate)

AF-725-P-SCR PRODUCTION CHART

AIR TEMPERATURE WATER TEMPERATURE

50 F/10C 70 F/21C 80 F/27C
50
F/10
C 654 lbs/297 kgs 588 lbs/267 kgs 552 lbs/251 kgs

70
F/21
C 639 lbs/290 kgs 563 lbs/256 kgs 521 lbs/237 kgs
90
F/27
C 562 lbs/255 kgs 479 lbs/218 kgs 448 lbs/204 kgs

725
Compressor Model Copeland RS43CIEIAA214
Condenser Air Cooled
Refrigerant Charge 17 oz. R404a
Refrigerant Control Automatic Expansion Valve (34-PSI)
Inlet Water Supply 3/8 SAE Male Flare
Voltage 115V 60HZ
Total Amp Draw 15.5 Amps
Gearmotor Amp Draw 2 Amps
Gearmotor Electrical Rating 1/8 hp
Maximum Fuse Size 20 Amp

166240010 4
 INSTALLATION INSTRUCTIONS

You will get better service from the ice machine, longer life and greater convenience if you choose its location
with care.

Here are a few points to consider:

1. Select a location as close as possible to where you are going to use the ice.

2. Allow a minimum of 6 space at sides and rear of machine for ventilation.

3. A kitchen installation is not desirable as a rule. If a kitchen installation is necessary, locate the machine as
far away
from the cooking area as possible. Grease laden air will form greasy deposits on the condenser. This re-
duces the ice making efficiency and necessitates thorough cleaning quite often.

4. If you install the unit in a storeroom, be sure the room is well ventilated.

NOTE: Do not install where the ambient and incoming water temperature will drop below 50F or rise to
over 100F.

NOTE: If water pressure exceeds 50 lbs., a water pressure regulator should be installed in water inlet
line between water shutoff valve and strainer. Minimum incoming water pressure required is 22 lbs..

A. Uncrate the unit by removing the staples or nails from the bottom of the carton and lift off.

B. Remove the bolts holding the skid to the machine.

C. If legs are used, adjust the leveling legs of the storage bin until the unit is level and all four (4) legs are
in solid contact with the floor. Leveling is very important to obtain proper draining.

D. Provide a cold water supply line to the area selected for the installation of the unit. The incoming wa-
ter line should have a shutoff valve provided at a convenient location close to the ice maker. The wa-
ter strainer provided with the unit should be installed on the downstream side of the shutoff valve.
The supply line must be adequately sized to compensate for the lengths of the incoming water run.
The machine is equipped with a 3/8 male flare connection for the incoming water line.

NOTE: ALWAYS FLUSH OUT WATER LINES BEFORE STARTING UNIT.

Water cooled units have a water regulating valve that is factory set to operate at 270 to 310 PSIG
head pressure for R404a (water outlet temp. approx. 105F) This should be checked at the time the
unit is being installed.

Two water inlet connections are provided on water cooled units, one for the ice making (evaporator)
section, the other is for the water cooled condenser. Both connections are 3/8 male flare fittings. In-
let water to the condenser will go to the water regulating valve first, then to the condenser coil and out
the drain.

The reason for separate water inlet connections is that some installations use a water tower for cooling
the water used in the water cooled condenser and some installations use treated water for the ice
making inlet water.

A separate drain will be required for the outlet of the water cooled condenser.

E. Provide a suitable trapped open drain as close as possible to the area where the ice maker is going to
be installed. This may be an existing floor or a 1 1/4 trapped open drain. Connect the drain line to
the rear of the unit and run it with a good fall to the open drain. All plumbing must be installed accord-
ing to local codes. The storage bin drains by gravity, and therefore the drain line must maintain a
gradual slope to an open drain and should be insulated.

NOTE: IN SOME CASES IT MAY BE NECESSARY TO INSULATE THE WATER SUPPLY LINE AND DRAIN
LINE. CONDENSATE DRIPPING TO THE FLOOR CAN CAUSE SERIOUS STAINING OF CARPETS OR
HARDWOODS.
5 166240010
 F. Connect a drain hose to the condensate drain stub tube.

NOTE: All plumbing must be done in accordance with national and local codes.

G. Connect the electrical supply line to the unit.

NOTE: Make sure the proper voltage and number of wires are provided. See serial plate for this in-
formation.

NOTE: All wiring must conform to national and local codes.

H. Turn on water supply and observe the water level in evaporator sections which should be no less than
1/4 below the inclined discharge chute opening of the shell.

I. Turn machine on and check for proper voltage and amp draw on the entire unit as well as components
such as the gearmotor and fan motor.

J. Check refrigerant circuit and all plumbing connections for leaks, etc.

K. Check bin thermostat or mechanical shutoff for proper operations. In the midrange the bin thermo-
stat will open at 42 and has a 6 differential.

ADJUSTMENT PROCEDURE

WARNING: WATER LEVEL MUST BE MAINTAINED AT THE TOP OF THE EVAPORATOR.

WATER LEVEL

FIGURE 4. WATER LEVEL ADJUSTMENT PROCEDURE

1. Remove gearmotor and auger.

2. Adjust float valve to get water level to top seam of the evaporator.

3. Reinstall auger. WATER LEVEL WILL RISE WHEN AUGER IS INSERTED BUT WHEN THE MACHINE
IS TURNED BACK ON AND ICE STARTS BEING MADE, THE WATER LEVEL WILL GO BACK TO THE
ORIGINAL SETTING.

4. Reinstall gearmotor assembly and start machine.

166240010 6
TYPICAL WATER CIRCUIT

The supply water enters the float chamber through a small orifice. The water level rises and lifts the buoyant
float with it. The float attached to the float arm seats a valve to shut off any further water supply. As water
leaves the float chamber, the level drops along with the float and arm, causing the valve to open and admit more
water. Thus the water level is maintained automatically as the machine operates.

Water now flows through a hose connected to the float chamber and enters the opening of the evaporator shell.
The water level in the shell will rise to the same level that is maintained in the float chamber. The water that is in
immediate contact with the center post evaporator will be reduced in temperature. As a result, freezing occurs
and ice forms on the surface of the evaporator.

As more water is frozen, the thickness of the ice increases until it exceeds the distance allowed between the
evaporator and auger. The auger rotates at a slow speed to wipe off the accumulated ice as well as help it to
the surface. After the ice reaches the surface it is discharged through the top opening in the shell. An ice chute
attached to the shell conveys the ice to the storage bin where it accumulates in the insulated bin until it is used.
The ice will pile up to a point where the bin thermostat tubing is located. When the ice touches this brass tubing,
the unit will shutoff and remain off until enough ice is used or melted to reduce the pile. Any ice that melts will
pass through the drain and drain hose to an open drain.

WATER IN

ICE
OUT
FLOAT
CHAMBER

EVAPORATOR
CHAMBER

FIGURE 5. TYPICAL WATER CIRCUIT

7 166240010
TYPICAL REFRIGERANT CIRCUIT

Heat always flows from hot to cold and therefore, the heat load supplied to the evaporator section by water
gives up its heat to the refrigerant which is at a temperature below the freezing point of water. This refrigerant
now passes through the heat exchanger back to the compressor, as a low pressure vapor.

This low pressure vapor is compressed in the compressor, as it leaves the compressor at a high pressure in va-
por form it enters the top of the condenser. The condenser has a rapid flow of cool air across it which removes
much of the heat from the hot refrigerant vapor.

As the vapor, passing through the condenser, loses heat it condenses back to a liquid since it is still under high
pressure and cooler than when it entered the condenser. The liquid refrigerant then passes through the drier/fil-
ter still under pressure and goes through the heat exchanger where further cooling takes place. As the refriger-
ant leaves the automatic expansion valve, the pressure has dropped, causing the refrigerant to vaporize and boil
off as it picks up heat in the evaporator and since the pressure is low, the refrigerant will be cold.

AXV
HEAT
EXCHANGER
EVAPORATOR

CONDENSER COMPRESSOR

DRIER/FILTER

FIGURE 6. TYPICAL REFRIGERANT CIRCUIT

166240010 8
 ELECTRICAL CIRCUIT

CIRCUIT DESCRIPTION

As the manual onoff circuit breaker switch is pushed to on, an electrical circuit is completed to the gearmotor
via the circuit breaker gearmotor overload, power relay/contactor, gearmotor delay thermostat and the bin ther-
mostat. After the previous circuit has been completed the condenser fan motor will start as will the compressor
(via the high pressure control, the compressor starting relay and low ambient control).

ONOFF SWITCH/CIRCUIT BREAKER

This switch interrupts power to the entire unit. The switch has a circuit breaker incorporated into its design. This
circuit breaker will trip out in the event the gearmotor draws to high of amps. In such an event the power is inter-
rupted to the unit. To reset the circuit breaker and reestablish power to the unit, push the switch to the off posi-
tion and then back to the on position.

BIN THERMOSTAT

This is electrically in series with the ice making system. when the bin is full, the contact opens, terminating
power to the machine.

HIGH PRESSURE CONTROL

Switch contact will open at 450 PSI for R404a breaking the circuit to the compressor. This control is manually
resetable.

GEARMOTOR START RELAY

This is a current type relay which means as the gearmotor run winding comes on the line, the current draw ini-
tially is relatively heavy through the relay coil (coil is in series with run winding). It then acts like a normal relay
and the N.O. start contact makes, completing a circuit through the start capacitor to the start winding. As the
gearmotor picks up speed, the amp draw through the relay coil drops off allowing the armature to return to its
normal position (start contact opens). This action removes the start winding from the circuit.

POWER RELAY/CONTACTOR

This relay controls the compressor power only.

FAN CYCLING SWITCH

The function of this switch is to maintain condensing pressures at a satisfactory level duringlow ambient condi-
tions. The switch breaks the circuit to the condenser fan motor at 205 PSI and makes the circuit at 275 PSI.

DELAY THERMOSTAT

This thermostat keeps the gearmotor running until the suction line temperature reaches 45 after the full bin
switch terminates power to the power relay.
9 166240010
COMPRESSOR START RELAY

This is a current type relay and contains a N.O. contact which is connected in series with the start winding of the
compressor. The relay coil is electrically in series with the run winding. When power is applied, the compressor
draws high current which sets up a magnetic field in the magnet coil which causes the relay to operate, closing
the relay contact. As the compressor approaches operating speed, the current flowing through the coil de-
creases, permitting the relay contact to open, thereby opening the starting circuit.

POTENTIAL RELAYS

The potential relay is used as a compressor starting relay, The contact in the potential relay is N.C.. The mag-
net coil is connected across (parallel) the start winding and is affected by induced voltage, generated by the start
winding. As the compressor comes up to design speed, the voltage across the relay coil increases and at run-
ning speed is sometimes as much as 2 1/2 times the supply voltage. This voltage sets up a magnetic field
which causes the relay to operate. The starting relay is calibrated to remove the start capacitor (open the start-
ing circuit) at approximately 85% of the motor design speed.

NOTE: BOTH TYPES OF RELAYS ARE DESIGNED TO OPERATE WITHIN VERY NARROW LIMITS OF
VOLTAGE AND CURRENT DICTATED BY MOTOR DESIGN, THEREFORE, WHEN MAKING A REPLACE-
MENT OF A RELAY ALWAYS PROVIDE AN EXACT REPLACEMENT, RECOMMENDED BY THE COMPRES-
SOR MANUFACTURER.

CAPACITORS GENERAL

An electrical capacitor is a device which stores up electrical energy. Capacitors are used with single phase mo-
tors to provide starting torque and improve running characteristics; by feeding this energy to the start winding in
step with the run winding.

Any capacitor has three (3) essential parts, two (2) of which are usually foil plates separated and insulated by
the third part called the dielectric.

Two general types of capacitors are used with electric motors. The electrolytic starting capacitor usually uses a
very thin film of oxide on the metallic plate as the dielectric. The running capacitor usually is of the liquid filled
type.

166240010 10
 MAINTENANCE

THE FOLLOWING MAINTENANCE SHOULD BE PERFORMED AT LEAST EVERY SIX MONTHS ON

FLAKED ICE MACHINES:

1. Check power supply with machine running for proper voltage.

2. Check water level in the float tank reservoir. Water level should be maintained at the top of the evaporator.
Adjust if necessary. (See illustration and adjustment procedure)

3. Clean the aircooled condenser coil with a stiff brush or vacuum cleaner (See procedure)

CAUTION: CONDENSER COOLING FINS ARE SHARP, USE CARE WHEN CLEANING.

4. Clean the ice storage bin and flush the bin drain at least once a month.

5. If a water conditioner is installed in the inlet water line, change, replace, or clean the filter, strainer or car-
tridge as required.

6. If heavy mineral deposits on the auger and evaporator shell are encountered due to bad local water condi-
tions, follow sanitizing and cleaning procedure.

7. Loosen holddown cam locks and remove gearmotor assembly.

8. Check thrust washer; replace if noticeably worn.

9. Lift out auger and examine for wear. The corkscrew auger guide bushing pressed into the drive block
should be checked for wear. Replace if loose or if worn flat with auger drive block. If the Helix auger on the
corkscrew auger round bar becomes flat on the inside more than 1/8 of an inch over a length of two inches
or more it should be replaced.

NOTE: HELIX AUGERS DO HAVE MACHINED FLAT RELIEF SURFACES. DONT CONFUSE THEM WITH
WORN FLAT AREAS.

Check the insert in the bottom ring of the Helix auger and replace if excessively worn.

10. Check shell vertical strips for wear. Replace the shell if excessive wear is shown.

11. Check ORing, replace if worn or cut.

12. Reassemble, steps 7 through 11.

CAUTION: IN REASSEMBLING THE AUGER GEARMOTOR, THE HOLD DOWN CLAMPS

MUST BE RIGHT AND SECURE. IN REINSTALLING THE EVAPORATOR SHELL, BE
ABSOLUTELY SURE THAT THE O RING IS NOT PINCHED OFF AS THIS WOULD CAUSE A
WATER LEAK AROUND THE BASE OF THE EVAPORATOR. LUBRICATE THE O RING WITH FOOD
GRADE LUBRICANT BEFORE REASSEMBLING SHELL. IN REASSEMBLING THE AUGER
GEARMOTOR, THE HOLD DOWN CLAMPS MUST BE RIGHT AND SECURE. IN REINSTALLING THE
EVAPORATOR SHELL, BE ABSOLUTELY SURE THAT THE O RING IS NOT PINCHED OFF AS THIS
WOULD CAUSE A WATER LEAK AROUND THE BASE OF THE EVAPORATOR. LUBRICATE THE O
RING WITH FOOD GRADE LUBRICANT BEFORE REASSEMBLING SHELL.

13. Check for alignment of ice chute. Make sure chute gasket is not blocking path of ice flow.

14. Check bin thermostat operation. In the midrange position the bin thermostat will open at 42 and has a 6
differential.
11 166240010
SANITIZING AND CLEANING PROCEDURE

1. Turn unit off at switch in upper rear right side panel.

2. Turn water off and remove water hose from bottom of float chamber inside of ice bin and allow to drain from
the evaporator via the hose end; or

3. Remove float chamber cover and while holding float up to prevent more water from entering the float
chamber, remove water hose from float chamber and proceed to drain the float chamber and evaporator.

4. With water still off, restore water hose to float chamber and add 1 oz. of sanitizer (see note below). Turn
water on.

5. Remove the bin door, float chamber cover, ice chute trim cover, two thumb screws and chute trim gasket.

6. Using soap, hot water, and a nonmetallic bristle brush or plastic scouring pad, scrub the parts removed in
step 4 as well as the interior of the ice bin, ice chute, thermowell, door tracks, ice bin top, and around bin
opening.

NOTE: Use care when cleaning around thermowell sensing tube; the small capillary is easily broken.
Rinse all parts in clean water.

7. In a 5 gallon bucket, mix a sanitizing solution of 1 oz. of sanitizer to 1 gallon of warm water (100 to 120 F).

8. Place all small, loose parts into the sanitizing solution and allow them to soak for 10 minutes.

9. Using a clean cloth and the sanitizing solution, wipe down the interior of the ice chute, thermowell door
tracks, ice bin top, and around bin opening. Allow to air dry.

10. Reassemble the float chamber cover, ice chute gasket and cover, and bin door.

11. Turn unit switch on and allow machine to make ice for at least 1/2 hour then discard all of the ice. DO NOT
ALLOW ICE WITH SANITIZER IN IT TO BE USED.

NOTE: APPROVED SANITIZER: Household bleach such as HiLex or Clorox.

WATER TREATMENT

During the freezing process, the impurities in the water have a tendency to be rejected.

However, the more dissolved solids in the water, the more troublesome the freezing operation will be. Bicarbon-
ates in the water are the most troublesome of the impurities. These impurities will cause scaling on the evapo-
rator, clogging of the float valve mechanism and other parts in the water system. If the concentration of impuri-
ties is high, wet mushy ice may be the result.

Parts of the ice maker, that are in contact with the water or ice, may corrode if the water is high in acidity. In
some areas, water may have to be treated in order to overcome some of the problems that arise because of the
mineral content.

IMI Cornelius has water filter/treatment systems available to control imputities found in your water supply. Con-
tact your local dealer for more information.

166240010 12
WINTER STORAGE

If the unit is to be stored in an area where the temperature will drop below freezing, it is most important that all
water lines be drained to prevent them from freezing and possible rupture.

To blow out the water line, disconnect the water supply at the cabinet inlet and use air pressure to force the wa-
ter into the water reservoir pan. This can then be removed from the water pan.

WATER COOLED CONDENSER To remove water from condenser unhook water supply and attach com-
pressed air hose. Start machine. As head pressure reaches the appropriate level opening the water regulating
valve, the compressed air will force the water out. Do not let the machine operate longer than necessary.

CLEANING THE CONDENSER (AIR COOLED)

In order to produce at full capacity, the refrigeration condenser must be kept clean. The frequency of cleaning
will be determined by surrounding condition. A good maintenance plan calls for an inspection at least every two
months.

Remove the unit compartment grill at the front. With a vacuum cleaner, remove all accumulated dust and lint
that has adhered to the finned condenser.

CAUTION: CONDENSER COOLING FINS ARE SHARP. USE CARE WHEN CLEANING.

13 166240010
 BK
YL

ONOFF SWITCH
GR CIRCUIT BREAKER WH
RATED 2.0 AMPS

BK
WH
BK

BK
BL

GEAR
BIN BL MOTOR
THERMOSTAT WH
3 GEAR MOTOR
START CAPACITOR M
BK YL
2 4 6477 MFD 165 VAC
BL
RD RD
GEAR MOTOR
START RELAY

MANUAL RESET WH
HIGH PRESS CNTRL FAN MOTOR
C.O. 450 PSIG M
BK BK

FAN SWITCH
C.O. 205 C.I. 275 WH
BK
BK
COMPRESSOR COMPRESSOR
BL OVERLOAD 1
R 2
C RD 5
1 S
BK YL BK
BK 3
WH COMPRESSOR COMPRESSOR
START RELAY START CAPACITOR
145174 MFD 220 VAC
BK
CONTACTOR

115 VOLTS 60 Hz

AF200PSCR

Part No. 161909061

Artwork 50922

FIGURE 7. WIRING DIAGRAM AF 200P-SC-R 115 VOLTS 60 HZ

166240010 14
 RD BL

BR
ONOFF SWITCH
LB GN/Y CIRCUIT BREAKER
RATED 1.5 AMPS

RD
BK

BL
BL
BL
GEAR
BIN GEAR MOTOR MOTOR
THERMOSTAT RD
3 START CAPACITOR
2125 MFD M
BL YL
2 4 220/250 VAC
BL
RD RD
GEAR MOTOR GN/Y
START RELAY

MANUAL RESET RD
HIGH PRESS CNTRL FAN MOTOR
C.O. 450 PSIG M
BK BK

FAN SWITCH
C.O. 205 C.I. 275 GN/Y

BK
BL RD
COMPRESSOR COMPRESSOR
OVERLOAD RD M BK
BK R 2
BR BK C
1 S
RD BL YL BK
LB S 1
BK GN/Y
RD COMPRESSOR COMPRESSOR
START RELAY START CAPACITOR
5060 MFD 330 VAC
RD
CONTACTOR

220 VOLTS 50 Hz

AF200PSC50R

Part No. 161909064

Artwork 50929

FIGURE 8. WIRING DIAGRAM AF-200-P-SC-50-R 220 VOLTS 50 HZ

15 166240010
 BK
YL

GW ONOFF SWITCH
CIRCUIT BREAKER WH
RATED 2.0 AMPS

BK
WH
BL

BK
BL

BL DELAY GEAR
BL YL
THERMOSTAT MOTOR
WH
BIN 3 GEAR MOTOR
THERMOSTAT START M
BK YL
2 4 CAPACITOR
RD
RD RD
RD GEAR MOTOR
START RELAY
BL
BL
BK BK M BK
WIRE NUT
FAN SWITCH CONDENSOR FAN
C.I. 275 C.O.205
WH
CONTROL
HIGH PRESSURE BK
C.O. 450 PSI
COMPRESSOR COMPRESSOR
OVERLOAD RD
R
C COMPRESSOR
1 S START
BL RD CAPACITOR
243292 MFD
BL YL 115 VAC
OR

BK
BK 2
CONTACTOR 5
POTENTIAL
START RELAY 1

115 VOLTS 60 Hz

AF525SCR
AF725SCR

Part No. 161909062

Artwork 50923
Rev. B

FIGURE 9. WIRING DIAGRAM AF525SC-R AND AF725-SC-R 115 VOLTS 60 HZ

166240010 16
 ONOFF SWITCH
GW CIRCUIT BREAKER
RATED 1.5 AMPS
LB
RD
BR
BK

BL
YL
GEAR MOTOR
BL DELAY START RELAY
BL GEAR
THERMOSTAT MOTOR
BIN 3 YL
THERMOSTAT BK GEAR MOTOR
START M
2 4 YL
RD CAPACITOR
RD RD RD
GW

RD
FAN MOTOR

BK BK M BK
BL
WIRE NUT
CONTROL FAN SWITCH
HIGH PRESSURE GW
COMPRESSOR
OVERLOAD COMPRESSOR
RD
1 R
C COMPRESSOR
RD S START CAPACITOR
BL YL
4352 MFD 330 V
BK GW
RD BL
BK L
RD S
COMPRESSOR
START RELAY M
CONTACTOR RD

220 VOLTS 50 Hz

AF/WF525PSC50R

Part No. 161909063

Artwork 50925
Rev. A

FIGURE 10. WIRING DIAGRAM AF/WF-525PSC-50-R 220 VOLTS 50 HZ

17 166240010
 SERVICE ANALYSIS

Trouble Probable Cause Remedy

UNIT WILL NOT RUN A. Onoff switch in off position. A. Turn switch to on.
B. Defective onoff switch. B. Check and replace.
C. Blown fuse. C. Replace fuse and check for cause
of blown fuse.
D. Thermostat set too warm for D. Adjust colder.
ambient.
E. Power relay contacts corroded. E. Check and clean.
F. Defective thermostat. F. Check and replace.
G. Loose electrical connection. G. Check wiring.
H. Gearmotor overload protector H. Turn switch to off then to on.
has cut off machine.
COMPRESSOR CYCLES A. Low voltage A. Check line voltage
INTERMITTENTLY.
B. Dirty condenser B. Clean condenser
C. Air circulation restricted C. Remove restriction
D. Defective condenser fan motor D. Check and replace
E. Defective relay, overload E. Check and replace
protector or starting capacitor.
F. Loose electrical connection F. Check wiring
MAKING WET ICE. A. Surrounding air temperature A. Correct or move unit
too high
B. High water level in float B. Lower water level, see page 6
reservoir
C. Dirty condenser C. Clean condenser
D. Faulty compressor D. Check and replace*
E. Refrigerant leak E. Check and repair
F. O ring leaking at bottom of F. Check and replace
evaporator shell
*NOTE: Special care must be used with R404a (HP62) charged systems using (POE) Polyolester oil. The
refrigeration system must not be open longer than 15 min., and the appropriate drier must be used due
to the moisture absorption properties of the POE oil.
UNIT RUNS BUT MAKES NO A. Leak in refrigerant system A. Check and repair
ICE.
B. Moisture in system B. Check, dehydrate and add drier to
system
C. No water C. Check water supply
D. O ring leaking at bottom of D. Check and replace O ring
evaporator shell
E. Compressor not running E. Check and replace O ring
166240010 18
 Trouble Probable Cause Remedy
WATER LEAKS. A. Worn or bad float valve A. Check and replace
B. Float and arm assembly stuck B. Check and replace
C. O ring leaking at bottom of C. Check and replace
evaporator shell
D. Storage bin drain and tubing D. Check and repair
EXCESSIVE NOISE OR A. Mineral or scale deposits on A. Remove and clean inside
CHATTERING. inside of evaporator shell surfaces by immersing evaporator
shell in ice machine cleaner
B. Intermittent water supply B. Check inlet water line
C. Water level in float tank too C. Check and adjust water level
low
D. Auger gearmotor endplay or D. Repair or replace
worn bearings
E. Air lock in gravity water supply E. Check and adjust warmer
line from float tank to
evaporator shell
MACHINE RUNS WITH FULL A. Storage bin thermostat set too A. Check and adjust warmer
BIN OF ICE. cold
B. Bin thermostat thermowell out B. Adjust thermowell
of path of ice
UNIT OFF ON RESET. A. Ice jams up in evaporator shell A. Clean inside surface of
evaporator shell
B. Bin thermostat will not shutoff B. Check and adjust or replace
machine. Set too cold.
C. Auger motor has worn C. Check and replace
bearings
UNIT GOES OFF ON RESET. A. Ice chute out of alignment, A. Realign
restricted ice flow out of
evaporator section
B. Ice chute center separator B. Replace ice chute
bent restricting ice flow out of
evaporator section
C. Incoming water temperature C. Maintain temperature above 50F
too cold
D. Bin thermostat does not D. Replace bin thermostat if
shutoff when bin is full of ice necessary
E. Mineral or scale deposits on E. Inspect and clean
inside of evaporator shell and
evaporator
F. Strips loose or missing on F. Inspect and replace evaporator
inside of evaporator shell shell if necessary
G. Low ambient temperature in G. Maintain temperature above 50
room where unit is located
H. Gearmotor sticking which H. Check amp draw of gearmotor
causes it to draw excessive with an amprobe (1.7 amps)
amperage (over 2.0 amps)

19 166240010
 Trouble Probable Cause Remedy
UNIT GOES OFF ON RESET. I. Plugged expansion valve, I. Check back pressure, replace
(CONTD) causing low back pressure valve, evacuate and recharge
system, replace drierstrainer
J. Slight leak, causing low back J. Check back pressure, find gas
pressure leak, repair leak, evacuate
system, add drier and recharge
K. Loose holddown assy K. Check and tighten or replace
L. Auger worn excessively on the L. Replace auger
inside surfaces causing thicker
flaked ice to be made
M. Auger out of line causing M. Replace auger and evaporator
excessive wear on the lower shell
outside surface where it rubs
against evaporator shell liner
at the bottom
N. Broken auger N. Replace auger
O. Evaporator surfaces worn or O. Inspect and replace evaporator if
gouged, causing thicker ice to necessary
be made
P. Auger guide bushing worn P. Replace auger guide bushing
down (corkscrew type augers only)
Q. Loose gearmotor mounting Q. Check and tighten
plate
R. Low water level in float tank R. Adjust float arm to maintain
reservoir correct water level
S. Worn thrust washer S. Replace

166240010 20
ILLUSTRATED PARTS BREAKDOWN, SERIES 525725

10
6

12

34

9 11

32

37 7 8 25

24

28

35

27 5

23

17

2 18

16

15

31

30 20

19

14 13

26
33

36 22

29 21

FIGURE 11. PARTS BREAKDOWN

21 166240010
 PARTS LIST

ITEM NO . DESCRIPTION 200 525 725

1 Compressor (115V 60HZ) 162964053 162964011 162964011
Compressor (220V 50HZ) 162964054 162964038
2 Pad, Masonite 09115 36310 36310
3 HoldDown, Evaporator 163277001 163277002 163277002
4 Evaporator 01501 41100 41100
5 ORing 00122 03120 03120
6 Auger 04062 03796 03796
7 Shell, Evaporator 01508 09182 09182
8 Gasket, Evaporator Shell 01916 08666 08666
9 Washer, Thrust 08043 8043 08043
10 Plate, Gearmotor Mounting 04060 03163 03163
11 Chute, Inclined Ice 166046000 08720 08720
12 Gearmotor (Von Weiss; 115V 60HZ) 164826001 164826001 164826001
Gearmotor (Von Weiss; 220V 50HZ) 164826002 164826002
13 Condenser 02908 25446 25446
14 Shroud, Condenser 161890013 36074 36074
15 Blade, Condenser Fan 165595008 25578 25578
16 Motor, Condenser Fan (115V 60HZ) 23526 25242 25242
Motor, Condenser Fan (220V 50HZ) 23645 300835000
17 Bracket, Condenser Fan Motor 00260 36075 36075
18 Drier 166184001 166184001 166184001
19 Thermostat, Bin 09570 09570 09570
20 Relay, Gearmotor Start (Von Weiss; 115V 60HZ) 161627001 161627001 161627001
Relay, Gearmotor Start (Von Weiss; 220V 50HZ) 161627002 161627002
21 Control, High Pressure 165677006 165677006 165677006
22 Control, Fan Switch 165677005 165677005 165677005
23 Float Tank, Complete 21789 21789 21789
24 Float Valve Only 21924 21924 21924
25 Thermowell 20773 29541 29541
26 Relay, Power (115V 60HZ) 164884002 164884002 164884002
Relay, Power (220V 50HZ) 40713 40713
27 Clip, Delay Thermostat 25871 25871
28 Valve, Automatic Expansion 161921004 161921004 161921004
29 Relay, Compressor Start (115V 60HZ) 161998016 161998008 161998008
Relay, Compressor Start (220V 50HZ) 161998017 161998011
30 Capacitor, Compressor Start (115V 60HZ) 161165015 161165007 161165007
Capacitor, Compressor Start (220V 50HZ) 161165016 161165010
31 Capacitor, Gearmotor Start (Von Weiss; 115V 161165000 161165000 161165000
60HZ)
Capacitor, Gearmotor Start (Von Weiss; 220V 29519 29519
50HZ)
32 Screw, Wing 00890 00890 00890
33 Switch, OnOff/Circuit Breaker (115V 60HZ) 166220001 166220001 166220001
Switch, OnOff/Circuit Breaker (220V 50HZ) 166220000 166220000
34 Disc, Centering 20956 20956
35 Thermostat, Gearmotor Delay 25864 25864
36 Valve, Refrigeration Service 162978003 162978003 162978003
37 Bushing, Auger Guide 02040
166240010 22
 CABINET PARTS LIST

1 4

5 1

7
8

9
200 525 and 725

FIGURE 12. CABINET PARTS BREAKDOWN

ITEM DESCRIPTION AF200PSCR AF200SSCR AF525PSCR AF525SSCR AF725PSCR

NO . AF200PSC50R AF525PSC50R
1 Bin Door 09120 09120 09120 09120 36555
2 Door, Track, LH 25007 25007 25007 25007 25007
3 Door, Track, RH 08824 08824 08824 08824 08824
4 Door Trim 09112 09112 09112 09112 08681
5 Back Panel 163278001 25043 N/A N/A N/A
6 Front Panel 163275002 25853 163283002 26857 163283001
7 Side Louvered Panel 163275013 163275014 N/A N/A N/A
8 Upper Louvered Access N/A N/A 163275003 25042 163275003
9 Lower Louvered Access N/A N/A 163275001 24154 163275004

23 166240010
 CORNELIUS LIMITED COMMERCIAL WARRANTY PLAN
TO THE ORIGINAL OWNER OF A CORNELIUS COMMERCIAL FLAKE ICEMAKER
This warranty applies to Icemakers installed within the United States, Canada, Mexico and Puerto Rico
only.
For warranty information outside the U.S., Canada, Mexico and Puerto Rico, contact your nearest IMI Cornelius
Sales Office.

PARTS WARRANTY PERIOD

IMI CORNELIUS INC., hereinafter referred to as CORNELIUS, warrants to the original owner of a new CORNELIUS commercial flake ice
machine (Machine) who buys solely for commercial uses, that the Machine shall be free from defects in material and/or factory workmanship if
properly installed, operated and maintained, under normal and proper use and service conditions with competent supervision. The parts
warranty period is two years (24 months) from the date of installation or 27 months from the date of shipment by CORNELIUS whichever time
period elapses first. With respect to compressor and the evaporator, and the evaporator only for refrigeration leaks and restrictions which
would effect the normal operation of the unit, the warranty period will be five years (60 months) from the date of installation or 63 months from
the date of shipment by CORNELIUS whichever time period elapses first. The obligation of CORNELIUS under this warranty is limited to repair
or replacement (at the option of CORNELIUS) FOB factory in Mason City, Iowa of the part (or Parts) of any Machine that is proven defective.
LIMITED LABOR WARRANTY PERIOD

In addition to the parts warranty, CORNELIUS will pay scheduled straight time labor to repair or replace a defective component when failure
occurs within one year (12 months) from the date of installation or 15 months from the date of shipment by CORNELIUS whichever time period
elapses first. With respect to the compressor, evaporator, refrigeration condenser, condenser fan motor, and auger gearmotor, the labor
warranty period will be two years (24 months) from the date of installation or 27 months from the date of shipment by CORNELIUS whichever
time period elapses first. Time and rate schedules for labor compensation will be published periodically by CORNELIUS. Additional expenses
including but not limited to travel time, truck charges, overtime charges, material cost, accessing or removal of the ice machine,
normal prescribed maintenance cleaning, adjustments, and ice purchases are the responsibility of the original owner.
No parts warranty or labor allowance on the motor compressor assembly will apply when the ice machines refrigeration system is modified with
a condenser heat reclaim device, or parts and assemblies not provided by CORNELIUS, unless CORNELIUS provides approval, in writing, for
these modifications for specific locations.
The parts warranty shall not apply when destruction or damage is caused by alterations, unauthorized service, using other than factory
authorized replacement parts, risks of transportation, accidents, misuse, damage by fire, flood or acts of God. No components or assembly
from which the serial number or identification number has been altered or removed will be covered. Any defective parts to be repaired or
replaced must be returned to us through a CORNELIUS distributor/dealer, transportation charges prepaid, and they must be properly sealed
and tagged. The serial and model number of the Machine and the date of original installation of such Machine must be given. The warranty of
repaired or replaced parts will not extend beyond the period of the original warranty. The decision of the CORNELIUS Service Department
regarding the warrantability of parts and eligibility for the labor allowance will be final.
No representative, distributor/dealer or any other person is authorized or permitted to make any other warranty or obligate CORNELIUS to
make any other warranty or obligate CORNELIUS to any liability not strictly in accordance with this policy. This warranty is in lieu of all other
warranties expressed or implied and of all other obligations or of liabilities on our parts.
OUR LIABILITIES ARE LIMITED SOLELY AND EXCLUSIVELY TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT. WE ARE
NOT LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND WHATSOEVER. In those jurisdictions
where liability for damages cannot be disclaimed, original purchasers recovery shall not exceed the cost of the warranted product.
Except for descriptions of size, quantity and type, which may appear on CORNELIUS product with specifications of certain industry,
government or professional organizations standards which may appear as product information disclosures in CORNELIUS literature and other
documents from time to time, THIS WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
CORNELIUS MAKES NO WRITTEN WARRANTY TO ANY PURCHASER WHO BUYS FOR PERSONAL, FAMILY OR HOUSEHOLD USE.

IMI CORNELIUS INC. P/N 163238002

ONE CORNELIUS PLACE Effective March. 1, 1996
ANOKA, MINNESOTA 55303-6234 Starting with Production
Serial
Number Code 9603

166240010 24
IMI CORNELIUS INC.
Corporate Headquarters:

One Cornelius Place

Anoka, Minnesota 55303-6234
(763) 421-6120
(800) 238-3600