Light meter

From Wikipedia, the free encyclopedia

Jump to: navigation, search

A light meter is a device used to measure the amount of light. In photography, a light
meter is often used to determine the proper exposure for a photograph. Typically a light
meter will include a computer, either digital or analogue, which allows the photographer
to determine which shutter speed and f-number should be selected for an optimum
exposure, given a certain lighting situation and film speed.

Light meters are also used in the fields of cinematography and scenic design, in order to
determine the optimum light level for a scene. They are used in the general field of
lighting, where they can help to reduce the amount of waste light used in the home, light
pollution outdoors, and plant growing to ensure proper light levels.

Contents
[hide]

• 1 Use in photography
• 2 Exposure meter calibration
o 2.1 Exposure equations
o 2.2 Calibration constants
o 2.3 Calibrated reflectance
o 2.4 Cameras with internal meters
• 3 Exposure determination with a neutral test card
• 4 Use in illumination
• 5 See also
• 6 Notes
• 7 References

• 8 External links

[edit] Use in photography

A handheld digital incident-light meter, showing an exposure setting of aperture f/5.6 at a
framing rate of 24/s and ISO 500 speed. The light sensor is on top, under the white
integrating sphere.

The earliest type of light meters were called extinction meters and contained a numbered
or lettered row of neutral density filters of increasing density. The photographer would
position the meter in front of their subject and note the filter with the greatest density that
still allowed incident light to pass through. The letter or number corresponding to the
filter was used as an index into a chart of appropriate aperture and shutter speed
combinations for a given film speed.

Extinction meters suffered from the problem that they depended on the light sensitivity of
the human eye (which can vary from person to person) and subjective interpretation.

Later meters removed the human element and relied on technologies incorporating
selenium, CdS, and silicon photodetectors.

Amateur analog light meter (1968, USSR)

An automatic light meter/exposure unit from an 8 mm movie camera, based on a
galvanometer mechanism (center) and a CdS photoresistor, in opening at left.

Selenium and silicon light meters use sensors that are photovoltaic: they generate a
voltage proportional to light exposure. Selenium sensors generate enough voltage for
direct connection to a meter; they need no battery to operate and this made them very
convenient in completely mechanical cameras. Selenium sensors however cannot
measure low light accurately (ordinary lightbulbs can take them close to their limits) and
are altogether unable to measure very low light, such as candlelight, moonlight, starlight
etc. Silicon sensors need an amplification circuit and require a power source such as
batteries to operate. CdS light meters use a sensor based on photoresistance, i.e. their
electrical resistance changes proportionately to light exposure. These also require a
battery to operate. Most modern light meters use silicon or CdS sensors. They indicate
the exposure either with a needle galvanometer or on an LCD screen.

Many modern consumer still and video cameras include a built-in meter that measures a
scene-wide light level and are able to make an approximate measure of appropriate
exposure based on that. Photographers working with controlled lighting and
cinematographers use handheld light meters to precisely measure the light falling on
various parts of their subjects and use suitable lighting to produce the desired exposure
levels.

There are two general types of light meters: reflected-light and incident-light. Reflected-
light meters measure the light reflected by the scene to be photographed. All in-camera
meters are reflected-light meters. Reflected-light meters are calibrated to show the
appropriate exposure for “average” scenes. An unusual scene with a preponderance of
light colors or specular highlights would have a higher reflectance; a reflected-light meter
taking a reading would incorrectly compensate for the difference in reflectance and lead
to underexposure. Badly underexposed sunset photos are common exactly because of this
effect: the brightness of setting sun fools the camera's light meter and, unless the in-
camera logic or the photographer take care to compensate, the picture will be grossly
underexposed and dull.

This pitfall is avoided by incident-light meters which measure the amount of light
falling on the subject using an integrating sphere (usually, a translucent hemispherical
plastic dome is used to approximate this) placed on top of the light sensor. Because the
incident-light reading is independent of the subject's reflectance, it is less likely to lead to
incorrect exposures for subjects with unusual average reflectance. Taking an incident-
light reading requires placing the meter at the subject's position and pointing it in the
general direction of the camera, something not always achievable in practice, e.g., in
landscape photography where the subject distance approaches infinity.

Another way to avoid under- or over-exposure for subjects with unusual reflectance is to
use a spot meter: a reflected-light meter that measures light in a very tight cone, typically
with a one degree angle. An experienced photographer can take multiple readings over
the shadows, midrange and highlights of the scene to determine optimal exposure, using
systems like the Zone System. Many modern cameras include sophisticated multi-
segment metering systems that measure the luminance of different parts of the scene to
determine the optimal exposure. When using a film whose spectral sensitivity is not a
good match to that of the light meter, for example orthochromatic black-and-white or
infrared film, the meter may require special filters and re-calibration to match the
sensitivity of the film.

There are other types of specialized photographic light meters. Flash meters are used in
flash photography to verify correct exposure. Color meters are used where high fidelity in
color reproduction is required. Densitometers are used in photographic reproduction.

[edit] Exposure meter calibration

In most cases, an incident-light meter will cause a medium tone to be recorded as a
medium tone, and a reflected-light meter will cause whatever is metered to be recorded as
a medium tone. What constitutes a “medium tone” depends on meter calibration and
several other factors, including film processing or digital image conversion.

Meter calibration establishes the relationship between subject lighting and recommended
camera settings. The calibration of photographic light meters is covered by ISO
2720:1974.

[edit] Exposure equations

For reflected-light meters, camera settings are related to ISO speed and subject luminance
by the reflected-light exposure equation:

where

• N is the relative aperture (f-number)

• t is the exposure time (“shutter speed”) in seconds
• L is the average scene luminance
• S is the ISO arithmetic speed
• K is the reflected-light meter calibration constant
For incident-light meters, camera settings are related to ISO speed and subject
illuminance by the incident-light exposure equation:

where

• E is the illuminance
• C is the incident-light meter calibration constant

[edit] Calibration constants

Determination of calibration constants has been largely subjective; ISO 2720:1974 states
that

The constants K and C shall be chosen by statistical analysis of the results of a large
number of tests carried out to determine the acceptability to a large number of observers,
of a number of photographs, for which the exposure was known, obtained under various
conditions of subject manner and over a range of luminances.

In practice, the variation of the calibration constants among manufacturers is

considerably less than this statement might imply, and values have changed little since
the early 1970s.

ISO 2720:1974 recommends a range for K of 10.6 to 13.4 with luminance in cd/m². Two
values for K are in common use: 12.5 (Canon, Nikon, and Sekonic[1]) and 14 (Kenko[2]
and Pentax); the difference between the two values is approximately 1/6 EV.

The earliest calibration standards were developed for use with wide-angle averaging
reflected-light meters (Jones and Condit 1941). Although wide-angle average metering
has largely given way to other metering sensitivity patterns (e.g., spot, center-weighted,
and multi-segment), the values for K determined for wide-angle averaging meters have
remained.

The incident-light calibration constant depends on the type of light receptor. Two
receptor types are common: flat (cosine-responding) and hemispherical (cardioid-
responding). With a flat receptor, ISO 2720:1974 recommends a range for C of 240 to
400 with illuminance in lux; a value of 250 is commonly used. A flat receptor typically is
used for measurement of lighting ratios, for measurement of illuminance, and
occasionally, for determining exposure for a flat subject.

For determining practical photographic exposure, a hemispherical receptor has proven

more effective. Don Norwood, inventor of incident-light exposure meter with a
hemispherical receptor, thought that a sphere was a reasonable representation of a
photographic subject. According to his patent (Norwood 1938), the objective was
to provide an exposure meter which is substantially uniformly responsive to light incident
upon the photographic subject from practically all directions which would result in the
reflection of light to the camera or other photographic register.

and the meter provided for "measurement of the effective illumination obtaining at the
position of the subject."

With a hemispherical receptor, ISO 2720:1974 recommends a range for C of 320 to 540
with illuminance in lux; in practice, values typically are between 320 (Minolta) and 340
(Sekonic). The relative responses of flat and hemispherical receptors depend upon the
number and type of light sources; when each receptor is pointed at a small light source, a
hemispherical receptor with C = 330 will indicate an exposure approximately 0.40 step
greater than that indicated by a flat receptor with C = 250. With a slightly revised
definition of illuminance, measurements with a hemispherical receptor indicate “effective
scene illuminance.”

[edit] Calibrated reflectance

It is commonly stated that reflected-light meters are calibrated to an 18% reflectance,[3]

but the calibration has nothing to do with reflectance, as should be evident from the
exposure formulas. However, some notion of reflectance is implied by a comparison of
incident- and reflected-light meter calibration.

Combining the reflected-light and incident-light exposure equations and rearranging

gives

Reflectance R is defined as

A uniform perfect diffuser (i.e., one following Lambert's cosine law) of luminance L
emits a flux density of πL; reflectance then is

Illuminance is measured with a flat receptor. It is straightforward to compare an incident-

light measurement using a flat receptor with a reflected-light measurement of a uniformly
illuminated flat surface of constant reflectance. Using values of 12.5 for K and 250 for C
gives
With a K of 14, the reflectance would be 17.6%, close to that of a standard 18% neutral
test card. In theory, an incident-light measurement should agree with a reflected-light
measurement of a test card of suitable reflectance that is perpendicular to the direction to
the meter. However, a test card seldom is a uniform diffuser, so incident- and reflected-
light measurements might differ slightly.

In a typical scene, many elements are not flat and are at various orientations to the
camera, so that for practical photography, a hemispherical receptor usually has proven
more effective for determining exposure. Using values of 12.5 for K and 330 for C gives

With a slightly revised definition of reflectance, this result can be taken as indicating that
the average scene reflectance is approximately 12%. A typical scene includes shaded
areas as well as areas that receive direct illumination, and a wide-angle averaging
reflected-light meter responds to these differences in illumination as well as differing
reflectances of various scene elements. Average scene reflectance then would be

where “effective scene illuminance” is that measured by a meter with a hemispherical

receptor.

ISO 2720:1974 calls for reflected-light calibration to be measured by aiming the receptor
at a transilluminated diffuse surface, and for incident-light calibration to be measured by
aiming the receptor at a point source in a darkened room. For a perfectly diffusing test
card and perfectly diffusing flat receptor, the comparison between a reflected-light
measurement and an incident-light measurement is valid for any position of the light
source. However, the response of a hemispherical receptor to an off-axis light source is
approximately that of a cardioid rather than a cosine, so the 12% “reflectance”
determined for an incident-light meter with a hemispherical receptor is valid only when
the light source is on the receptor axis.

[edit] Cameras with internal meters

Calibration of cameras with internal meters is covered by ISO 2721:1982; nonetheless,

many manufacturers specify (though seldom state) exposure calibration in terms of K,
and many calibration instruments (e.g., Kyoritsu-Arrowin multi-function camera testers[4]
) use the specified K to set the test parameters.
[edit] Exposure determination with a neutral test card
If a scene differs considerably from a statistically average scene, a wide-angle averaging
reflected-light measurement may not indicate the correct exposure. To simulate an
average scene, a substitute measurement sometimes is made of a neutral test card, or gray
card.

At best, a flat card is an approximation to a three-dimensional scene, and measurement of

a test card may lead to underexposure unless adjustment is made. The instructions for a
Kodak neutral test card recommend that the indicated exposure be increased by ½ step
for a frontlighted scene in sunlight. The instructions also recommend that the test card be
held vertically and faced in a direction midway between the Sun and the camera; similar
directions are also given in the Kodak Professional Photoguide. The combination of
exposure increase and the card orientation gives recommended exposures that are
reasonably close to those given by an incident-light meter with a hemispherical receptor
when metering with an off-axis light source.

In practice, additional complications may arise. Many neutral test cards are far from
perfectly diffuse reflectors, and specular reflections can cause increased reflected-light
meter readings that, if followed, would result in underexposure. It is possible that the
neutral test card instructions include a correction for specular reflections.

[edit] Use in illumination

Light meters or light detectors are also used in illumination. Their purpose is to measure
the illumination level in the interior and to switch off or reduce the output level of
luminaires. This can greatly reduce the energy burden of the building by significantly
increasing the efficiency of its lighting system. It is therefore recommended to use light
meters in lighting systems, especially in rooms where one cannot expect users to pay
attention to manually switching off the lights. Examples include hallways, stairs, and big
halls.

There are, however, significant obstacles to overcome in order to achieve a successful

implementation of light meters in lighting systems, of which user acceptance is by far the
most formidable. Unexpected or too frequent switching and too bright or too dark rooms
are very annoying and disturbing for users of the rooms. Therefore, different switching
algorithms have been developed:

• difference algorithm, where light switch on lower light level than they switch off,
thus taking care that the difference between the light level of the 'on' state and 'off'
state is not too big
• time delay algorithms:
o certain amount of time must pass since the last switch
o certain amount of time of sufficient illumination.
[edit] See also
Photography
portal

Wikimedia Commons has media related to: Light meters

• Selenium meter
• Photometer | Photodetector
• Colorimetry | Photometry | Radiometry
• Light value
• Photomultiplier tubes for detecting light at very low levels.
• PIN diode solid state electronic devices for detecting incident light.

[edit] Notes
1. ^ Specifications for Sekonic light meters are available on the Sekonic web site
under “Products.”
2. ^ Konica Minolta Photo Imaging, Inc. left the camera business on March 31,
2006. Rights and tooling for Minolta exposure meters were acquired by Kenco
Co, Ltd. in 2007. Specifications for the Kenko meters are essentially the same as
for the equivalent Minolta meters.
3. ^ Some authors (Ctein 1997, 29) have argued that the calibrated reflectance is
closer to 12% than to 18%.
4. ^ Specifications for Kyoritsu testers are available on the C.R.I.S. Camera Services
web site under “kyoritsu test equipment.”

[edit] References
• Ctein. 1997. Post Exposure: Advanced Techniques for the Photographic Printer.
Boston: Focal Press. ISBN 0-240-80299-3.
• Eastman Kodak Company. Instructions for Kodak Neutral Test Card, 453-1-78-
ABX. Rochester: Eastman Kodak Company.
• Eastman Kodak Company. 1992. Kodak Professional Photoguide. Kodak
publication no. R-28. Rochester: Eastman Kodak Company.
• ISO 2720:1974. General Purpose Photographic Exposure Meters (Photoelectric
Type) — Guide to Product Specification. International Organization for
Standardization.
• ISO 2721:1982. Photography — Cameras — Automatic controls of exposure.
International Organization for Standardization.
• Jones, Loyd A., and H. R. Condit. 1941. The Brightness Scale of Exterior Scenes
and the Correct Computation of Photographic Exposure. Journal of the Optical
Society of America. 31:651–678.
 • Norwood, Donald W. 1938. Exposure Meter. US Patent 2,214,283, filed 14
November 1938, and issued 10 September 1940.

[edit] External links

• Meters Don't See 18% Gray An article suggesting that photographic light meters
are calibrated for 12% average reflectance.
• Exposure Metering: Relating Subject Lighting to Film Exposure (PDF) A
discussion of meter calibration and its practical effects.
• A Kodak guide to Estimating Luminance and Illuminance using a camera's
exposure meter. Also available in PDF.

Retrieved from "http://en.wikipedia.org/wiki/Light_meter"

Categories: Photography equipment | Electromagnetic radiation meters

Personal tools

• New features
• Log in / create account

Namespaces

• Article
• Discussion

Variants

Views

• Read
• Edit

Actions

• View history

Search

Navigation

• Main page
• Contents
• Featured content
• Current events
 • Random article

Interaction

• About Wikipedia
• Community portal
• Recent changes
• Contact Wikipedia
• Donate to Wikipedia
• Help

Toolbox

• What links here

• Related changes
• Upload file
• Special pages
• Permanent link
• Cite this page

Print/export

• Create a book
• Download as PDF
• Printable version

Languages

• Català
• Česky
• Deutsch
• Eesti
• Ελληνικά
• Español
• Français
• Bahasa Indonesia
• Italiano
• Lietuvių
• Nederlands
• 日本語
• Polski
• Português
• Русский
• Svenska
• Türkçe
• 中文
• This page was last modified on 6 August 2010 at 02:12.
• Text is available under the Creative Commons Attribution-ShareAlike License;
additional terms may apply. See Terms of Use for details.
Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a non-
profit organization.
• Contact us

• Privacy policy
• About Wikipedia
• Disclaimers