VERITAS NetBackup FlashBackup™ 3.

System Administrator’s Guide

UNIX

June 2000
100-001493
Disclaimer
The information contained in this publication is subject to change without notice.
VERITAS Software Corporation makes no warranty of any kind with regard to this
manual, including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose. VERITAS Software Corporation shall not be liable for
errors contained herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this manual.

Copyright
Copyright © 1998-2000 VERITAS Software Corporation. All rights reserved. VERITAS is a
registered trademark of VERITAS Software Corporation in the US and other countries.
VxVM, VxVA, VxFS, and FirstWatch are registered trademarks of VERITAS Software
Corporation. The VERITAS logo, VERITAS NetBackup, VERITAS NetBackup
FlashBackup, VERITAS Volume Manager, VERITAS File System, VERITAS HSM,
VERITAS Media Librarian, CVM, VERITAS Quick I/O, and VxSmartSync are trademarks
of VERITAS Software Corporation. All other trademarks or registered trademarks are the
property of their respective owners.
Portions of this software are derived from the RSA Data Security, Inc. MD5
Message-Digest Algorithm. Copyright 1991-92, RSA Data Security, Inc. Created 1991. All
rights reserved.
Printed in the USA, June 2000.
VERITAS Software Corporation
1600 Plymouth St.
Mountain View, CA 94043
Phone 650–335–8000
Fax 650–335–8050
www.veritas.com
Contents
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii
Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii
Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Type Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Notes and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Key Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Command Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix
Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Chapter 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Technical Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Chapter 2. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing FlashBackup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Step 1: Load From Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Step 2: Distribute FlashBackup to the Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Step 3: Install snap Driver (Solaris) or Move FlashBackup Library (HP) . . . . . . . . 11
Deinstalling FlashBackup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

iii
 Server Deinstall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Client Deinstall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Chapter 3. Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
General Class Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Client List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
File List and Cache . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Allow Multiple Data Streams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
General Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Client Read Timeout Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Chapter 4. Using FlashBackup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Performing a Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Automatic Backup of a FlashBackup Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Manual Backup of a FlashBackup Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Performing a Server-Directed Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Note on Restoring Individual Directories or Files . . . . . . . . . . . . . . . . . . . . . . . . 20
Notes on Restoring Raw Partitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Performing a Client-Directed Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
To Restore Individual Directories or Files with xbp . . . . . . . . . . . . . . . . . . . . . . . . . 21
To Restore an Entire Raw Partition with xbp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Gathering Information and Checking Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Before Contacting VERITAS Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Particular FlashBackup Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Appendix A. Solaris snapctl Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Command Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
snapoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
snaplist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

iv NetBackup FlashBackup System Administrator’s Guide

 snapcachelist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
snapstat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Contents v
vi NetBackup FlashBackup System Administrator’s Guide
About This Guide
This guide explains how to install, configure, and use VERITAS NetBackup
FlashBackupTM. In this publication, VERITAS NetBackup is referred to as NetBackup and
VERITAS NetBackup FlashBackup is referred to as FlashBackup.

Audience
This guide is intended for the system administrator responsible for configuring
FlashBackup and assumes a thorough working knowledge of NetBackup administration.

Organization
◆ Chapter 1, “Introduction,” is an overview of the product’s capabilities.
◆ Chapter 2, “Installation,” explains how to install FlashBackup.
◆ Chapter 3, “Configuration,” explains how to configure your system to use
FlashBackup. This chapter supplements the information in the NetBackup System
Administrator’s Guide - UNIX.
◆ Chapter 4, “Using FlashBackup,” explains how to back up a FlashBackup class and
how to restore files from FlashBackup backups.
◆ Appendix A, “Solaris snapctl Driver,” provides information about the snapctl
driver.

Related Manuals
◆ NetBackup Release Notes
Describes the platforms and operating systems that are supported and provides
operating notes that may not be in the manuals or the online help.
◆ NetBackup System Administrator’s Guide - UNIX
Explains how to configure and manage NetBackup on a UNIX platform.

vii
Conventions

◆ NetBackup User’s Guide - UNIX

Explains how to perform user-directed backups, restores, and archives on a UNIX
client.
◆ Media Manager System Administrator’s Guide - UNIX
Explains how to configure and manage the storage devices and media that UNIX
NetBackup servers use for backups.
◆ Media Manager Device Configuration Guide
Provides information about configuring storage devices on UNIX systems.
◆ NetBackup Troubleshooting Guide - UNIX
Provides troubleshooting information for NetBackup.

Conventions
The following explains typographical and other conventions used in this guide.

Type Style

Table 1. Typographic Conventions

Typeface Usage
Bold fixed width Input. For example, type cd to change directories.
Fixed width Paths, commands, filenames, or output. For example: The default installation
directory is /opt/VRTSxx.
Italics Book titles, new terms, or used for emphasis. For example: Do not ignore cautions.
Sans serif (italics) Placeholder text or variables. For example: Replace filename with the name of your
file.
Sans serif (no italics) Graphical user interface (GUI) objects, such as fields, menu choices, etc.
For example: Enter your password in the Password field.

Notes and Cautions

Note This is a Note and is used to call attention to information that makes it easier to use
the product or helps you to avoid problems.

viii NetBackup FlashBackup System Administrator’s Guide

 Getting Help

Caution This is a Caution and is used to warn you about situations that can cause data
loss.

Key Combinations
Some keyboard command sequences use two or more keys at the same time. For example,
you may have to hold down the Ctrl key before you press another key. When this type of
command is referenced, the keys are connected by plus signs. For example:
Press Ctrl+t

Command Usage
The following conventions are frequently used in the synopsis of command usage.
brackets [ ]
The enclosed command line component is optional.
Vertical bar or pipe (|)
Separates optional arguments from which the user can choose. For example, when a
command has the following format:
command arg1|arg2
the user can use either the arg1 or arg2 variable.

Getting Help
For updated information about this product, including system requirements, supported
platforms, supported peripherals, and a list of current patches available from Technical
Support, visit our web site:
http://www.veritas.com/
For product assistance, contact VERITAS Customer Support.
US and Canadian Customers: 1-800-342-0652
International Customers: +1 (650) 335-8555
VERITAS Customer Support can also be reached through electronic mail at:
[email protected]

About This Guide ix

Getting Help

x NetBackup FlashBackup System Administrator’s Guide

Introduction 1
FlashBackup is a separately priced option that combines the increased performance of
raw-partition backups with the ability to do individual file restores of ufs or VxFS file
systems on Solaris or of JFS or VxFS file systems on HP. This chapter provides an
introduction to FlashBackup and contains the following topics.
◆ Requirements
◆ Features
◆ Restrictions
◆ Technical Overview

Caution Do not use FlashBackup to back up HSM-managed file systems.

Requirements
FlashBackup requires the following components:
◆ A UNIX master server with NetBackup 3.4 or later installed.
◆ NetBackup clients that have Solaris 2.6, Solaris 7, or Solaris 8, and NetBackup 3.4 or
later client software installed, or NetBackup clients that have HP 11.00 and
NetBackup 3.4 or later installed.
◆ The FlashBackup dynamic shared library (libbpfsmap.so for Solaris or
libbpfsmap.sl for HP) must be installed on the clients.
◆ If you are using VxFS file systems, VxFS 3.3.2 or later must be installed on the clients.
If you are using JFS file systems on HP, JFS 3.3 or higher must be installed on the
clients.
◆ For Solaris only, the FlashBackup snapctl driver must be installed on the clients.
◆ A raw disk partition to act as the cache device.

1
Features

Features
The features that distinguish FlashBackup from other raw-partition backups and standard
file system backups are:
◆ FlashBackup backs up the following file systems: ufs (Solaris), VxFS (Solaris and HP),
and JFS (HP)
◆ Allows individual file restores
FlashBackup provides a file system mapping capability that allows individual files to
be restored from FlashBackup raw-partition backups.
◆ Supports multiple data streams
It is possible to split a backup into multiple data streams in order to further increase
the performance of FlashBackup raw-partition backups.
◆ Uses standard NetBackup utilities for raw partition restores
You can restore raw partitions from FlashBackup backups by using the NetBackup
server Java interface (jbpSA), or by using the standard xbp or bp restore raw
partitions mechanism on the FlashBackup client.
◆ The file system remains mounted during raw-partition backups
It is not necessary to unmount the file system or mount it read only, as with standard
raw-partition backups.
FlashBackup has on-line backup capability that allows the file system mounted on the
raw partition to be modified while the backup is in progress.
This on-line backup capability is made possible by backing up a snapshot of the raw
partition. The snapshot is a consistent image of the file system at the moment the
backup began. The snapshot mechanism is provided by the FlashBackup snapctl
driver for Solaris ufs backups, and by VxFS snapshot for VxFS backups.
◆ Provides economical use of kernel resources (Solaris only)
While a snapshot is active, the snapctl driver requires only four kilobytes of
physical RAM per gigabyte of snapped file system.
◆ Has no effect on file system reliability
The snapctl driver does not affect file system reliability. When a file system block is
updated, the write to the snapped partition always completes, regardless of errors
involving the snapshot. For example, the write will complete even if a cache overflow
occurs.

2 NetBackup FlashBackup System Administrator’s Guide

 Restrictions

◆ Provides increased performance

When used under the right conditions, FlashBackup provides increased backup
performance over other backup methods. For example, a FlashBackup of a file system
will complete in substantially less time than other types of backup, if the file system
contains a very large number of files and most of the file system blocks are allocated.
However, under conditions such as those below, FlashBackup will not necessarily be
faster than other backup types and may be slightly slower:
◆ If the file system contains a small number of large files.
◆ If the file system has a small number of files and most of the file system blocks are
not allocated.

Note While a snapshot is in effect, reads of the snapped file system will execute without
loss of performance. Writes to a snapped file system, however, will suffer speed
degradation of 200 to 300% the first time a particular block is written. After a block
has been cached, subsequent writes to that block will execute without degradation
in speed.

Restrictions
◆ FlashBackup does not support file systems managed by HSM.

Chapter 1, Introduction 3
Technical Overview

Technical Overview
The following figure shows the major NetBackup components involved in FlashBackup
backups.

Master server
Backup Solaris or HP
Request client
jnbSA or bprd
bpadm
Backup
Request
ifrfr
bpdbm
bpsched

Media server Class

Ba

info
ck
up
i
nfo

bpcd

Class
info Class bpcd
info
Class
bptm info
(parent) bpbrm
Backup Bac Ba bpbkar
kup ck
image up
ima bptm inf
ge o Class
(child)
info
Bac
ku p im libbpfsmap.so (Solaris)
age
libbpfsmap.sl (HP-UX)

Tape or Optical

Cache Cache
disk disk

Scheduled backups and immediate backups of FlashBackup classes are initiated and processed
in the same manner as standard class backups. However, the Individual file restore from raw
(ifrfr)attribute, which defines FlashBackup classes, causes bpsched to send the special

4 NetBackup FlashBackup System Administrator’s Guide

 Technical Overview

-ifrfr flag to bpbrm along with the other class information. bpbrm starts bpbkar with
the -ifrfr flag, which causes bpbkar to invoke the FlashBackup dynamic shared library
(libbpfsmap.so on Solaris, libbpfsmap.sl on HP).
During the backup, the dynamic shared library (libbpfsmap.so or
libbpfsmap.sl)performs the following tasks:
◆ Creates a file system map that represents files contained in the raw partition.
◆ If the backup type is a file incremental, the dynamic shared library creates a bit map
that associates blocks belonging to selected files with their physical addresses in the
partition. Note that block level incrementals are not supported.
◆ Turns on the raw-partition snapshot mechanism so that when a block is updated in
the partition, the previous contents of the block are written to the cache partition.
◆ Sends the backup information to bpbrm, which in turn directs the backup information
to bpdbm. The backup information is composed of:
◆ File system map name
◆ Bit map name (if incremental)
◆ Individual file names
◆ Raw-partition name
◆ Transmits the backup image to bptm. The backup image is composed of:
◆ File system map data blocks
◆ Bit map data blocks
◆ Raw-partition data blocks
◆ Turns off the snapshot mechanism.

Chapter 1, Introduction 5
Technical Overview

The following figure shows the major components involved in restoring files from
FlashBackup backup images.

Master server Solaris or HP

client

Restore Restore
request request
jbpSA bprd xbp or bp

Backup
info
bpdbm
sfr

Media server ap
m
em
st
sy
le fo
Fi in bpcd
r
fe
ans
t r
le
Fi

bptm
(parent) bpbrm bpcd
Dat
ab
loc
ks
bptm
(child)
Data blocks tar

Tape or Optical
Client
disk

During a restore, the user browses for and selects files from FlashBackup images in the
same manner as standard backup images. The difference is that bprd calls the sfr
program when processing FlashBackup images. During a restore, the sfr program
performs the following tasks:

6 NetBackup FlashBackup System Administrator’s Guide

 Technical Overview

◆ Retrieves information about the backup from bpdbm. The backup information is
composed of:
◆ File system map name and its media location.
◆ Bit map name and its media location.
◆ Raw-partition name and its media location.
◆ Using the backup information, sfr retrieves the file system map data by directing
bptm to the location of the file system map on the tape and then reading from the
tape. A similar procedure is followed to position bptm to obtain the bit map data
when restoring from incremental backup images and to obtain the raw-partition data
when restoring the raw partition.
◆ Then, using the information contained in the file system map, sfr directs bptm to the
location of the individual file data blocks on the tape.
bptm then reads the file data blocks from the tape and writes them to the client’s tar
program. Finally, tar writes the file data to the client disk.

Chapter 1, Introduction 7
Technical Overview

8 NetBackup FlashBackup System Administrator’s Guide

Installation 2
This chapter explains how to install and deinstall FlashBackup.

Prerequisites
◆ A UNIX master server with NetBackup 3.4 or later installed.
◆ NetBackup FlashBackup Solaris clients must have Solaris 2.6, Solaris 7, or Solaris 8
installed. NetBackup FlashBackup HP clients must have HP-UX 11.00 installed.
FlashBackup provides the necessary libraries and drivers for these clients.
◆ NetBackup 3.4 or later client software must also be installed.
◆ If you are going to perform VxFS backups, you must have VxFS 3.3.2 or later installed
on the clients.

Caution If you are using a version of NetBackup that is earlier than the version defined
for your platform, upgrade to the required version before installing
FlashBackup. Otherwise, your FlashBackup backups will work but restores of
files greater than two gigabytes will fail.

Installing FlashBackup

Step 1: Load From Media

1. Log in as root on the master server.

2. Make sure a valid license key for NetBackup FlashBackup has been registered by
entering the following command to list and add keys:
/usr/openv/netbackup/bin/admincmd/get_license_key

3. Insert the CD-ROM containing the FlashBackup software in the drive.

9
Installing FlashBackup

4. Change your working directory to the CD-ROM directory:

cd /cd_rom_directory
Where cd_rom_directory is the path to the directory where you can access the
CD-ROM. On some platforms, it may be necessary to mount this directory.

5. To install NetBackup FlashBackup, execute the following:

./install
Since other NetBackup products are included on the CD-ROM, a menu appears:

a. Select the NetBackup FlashBackup option.

b. Enter q to quit the menu.

c. When asked if the list is correct, answer y.

On all platforms, FlashBackup libraries are installed in
/usr/openv/lib/client/hardware/os
and the FlashBackup snapshot drivers and commands are installed in:
/usr/openv/netbackup/bin/driver/hardware/os
Where:
◆ hardware is Solaris, HP9000-800, or HP9000-700
◆ os is Solaris 2.6 or HP-UX11.00

Step 2: Distribute FlashBackup to the Clients

Note If the master server is a Solaris or HP system and the master server is also a client,
you do not have to distribute FlashBackup software to the client on the master
server. This distribution is done automatically when you load the software from the
media (see previous step). However, you must distribute the software as explained
below to all other clients that will be using FlashBackup.

1. Distribute FlashBackup client software to the desired UNIX clients by executing the
following commands as the root user on the Netbackup FlashBackup server.

a. Check whether bprd is running by executing:

/usr/openv/netbackup/bin/bpps

10 NetBackup FlashBackup System Administrator’s Guide

 Installing FlashBackup

b. If only one bprd shows up in the bpps output, there are no active backups or
restores. In that case, terminate the bprd daemon by executing:
/usr/openv/netbackup/bin/admincmd/bprdreq -terminate
If more than one bprd appears, wait until the backups and/or restores are
complete and then run /usr/openv/netbackup/bin/bpps again. When only
one bprd shows up, terminate the bprd daemon.

c. Distribute FlashBackup client software to the desired clients by executing the

following command. You may want to redirect the output of the command if you
have a large number of clients using FlashBackup:
/usr/openv/netbackup/bin/update_flashclients
Or, specify each client individually by executing the following (all on one line):
/usr/openv/netbackup/bin/update_flashclients -ClientList file
Where file is the name of a file each line of which contains the following three
parameters:
hardware_type operating_system hostname
For example:
Solaris Solaris2.6 mysparc
or
Solaris Solaris7 othersparc
or
HP9000-800 HP-UX11.00 myhp

2. After FlashBackup client software has been distributed to the desired clients, start the
NetBackup daemons as the root user on the master server by executing:
/usr/openv/netbackup/bin/initbprd

Step 3: Install snap Driver (Solaris) or Move FlashBackup Library (HP)

On each NetBackup client that will be using FlashBackup to back up ufs or VxFS mounted
file systems, execute the following:
/usr/openv/netbackup/bin/driver/fb_snap.install

Note On HP, this command moves the FlashBackup library to /usr/openv/lib.

Chapter 2, Installation 11
Deinstalling FlashBackup

Deinstalling FlashBackup

Server Deinstall
On the master server where you initially loaded the FlashBackup software, execute the
following:
For Solaris NetBackup servers, execute:
pkgrm SUNWnbfsh
For other UNIX NetBackup servers, delete the following:
/usr/openv/netbackup/bin/driver/HP9000*/HP_UX11.00/*
/usr/openv/netbackup/bin/driver/Solaris/Solaris2.6/*
/usr/openv/lib/client/*/libbpfsmap.*

Client Deinstall
On each NetBackup client that is using FlashBackup:

1. On Solaris only: execute the following to verify that no snapshots are active:
/usr/openv/netbackup/bin/driver/snaplist
If a snapshot is active, wait until the snapshot completes and then do step 2.

2. Execute the following command to deinstall the client software:

/usr/openv/netbackup/bin/driver/fb_snap.install -d

12 NetBackup FlashBackup System Administrator’s Guide

Configuration 3
To use the features provided by FlashBackup, you must add at least one FlashBackup type
of class to NetBackup. This chapter briefly explains how to configure FlashBackup classes.
Only the configuration differences between Standard and FlashBackup classes are
described here. For a detailed discussion of configuring NetBackup classes, see the
NetBackup System Administrator’s Guide - UNIX.
The following topics are covered in this chapter:
◆ General Class Attributes
◆ Client List
◆ File List and Cache
◆ Schedules
◆ General Configuration
Use the NetBackup Administration utility on the NetBackup master server to add your
classes.

General Class Attributes

When you select the general attributes for the class, always set the Class type attribute to
FlashBackup. A FlashBackup class also has the Individual file restore from raw attribute,
which is always set to Yes. This attribute lets you restore individual files from
raw-partition backups. For more information, see the Individual File Restore From Raw
discussion in the NetBackup System Administrator’s Guide - UNIX.
NetBackup forces the following attributes to No. You cannot change them.
◆ Follow NFS
◆ Cross mount points
◆ True image restore information
◆ Compression
◆ Encryption

13
Client List

◆ Block level incremental

Client List
The client list specifies the clients on which you installed the FlashBackup software. The
clients must be Solaris 2.6, 7, 8, or HP 11.00.

File List and Cache

Caution Do not use FlashBackup to back up HSM-managed file systems.

Note A client must contain all the raw partitions that are specified in the file list for
backups to succeed. Otherwise, you must put the clients in separate classes.

Exclude and include lists have no effect on FlashBackup backups.

The entries in the file list for a FlashBackup class are the same as for a standard
raw-partition backup, except that there must be a special CACHE= entry before any raw
partition entries.
For example:
CACHE=/dev/rdsk/c0t4d0s0
/dev/rdsk/c0t4d0s7
The CACHE= entry specifies the cache partition to be used for storing any updates to the
raw-partition entry while the backup is in progress.
◆ The raw-partition entry specifies the disk partition on the client to be backed up.
◆ For all entries in the file list, enter the full path name of the device file. Do not specify
wildcards (such as /dev/rdsk/c0*) as paths for any entry.

Note Ensure that you are specifying the actual character special device file for each entry.
FlashBackup will not work for block special device files.

◆ Links to the device files are permitted.

◆ You can include multiple entries in the same file list.
For example:
CACHE=/dev/rdsk/c0t4d0s0
/dev/rdsk/c0t4d0s7
CACHE=/dev/rdsk/c0t4d0s1
/dev/rdsk/c0t4d0s2

14 NetBackup FlashBackup System Administrator’s Guide

 File List and Cache

/dev/rdsk/c0t4d0s3
◆ The cache partition is part of the snapshot mechanism that preserves a consistent view
of the raw partition for NetBackup.
The basic requirements for the cache partition are:
◆ Must reside on the same host as the raw partitions that you are backing up.
◆ Multiple backups cannot use the same cache partition simultaneously on HP-UX
systems. If multiple classes list the same cache partition on HP-UX systems,
backups naming those classes must be run at different times to prevent a failure.
◆ Cannot be the raw partition being backed up, or one that is used as part of
another file system or virtual partition.
◆ Must be unmounted.
◆ Must have enough space to hold all the writes to the partition that may occur
during the backup. Note that backups during nonworking hours normally
require a smaller cache than a backup during peak activity times. Also see the
introductory section in Appendix A.
◆ You can include directives if Allow multiple data streams is set for the class (see
“Allow Multiple Data Streams,” below).

Allow Multiple Data Streams

If you select the Allow multiple data streams general attribute for the class, you can include
directives in the file list that will start multiple backups for each client that is backed up:
◆ The number of backups that start depends on the directives in the file list.
◆ The number of backups that can run concurrently depends on the number of available
storage units and the maximum jobs parameters (for example, Limit jobs per class).
Allow multiple data streams is useful for reducing the backup time for very large backups.
This is achieved by using multiple drives, multiplexing, or a combination of the two for
processing the streams concurrently.

Note For best performance, use only one data stream to back up each physical device on
the client. Multiple concurrent streams from a single physical device can adversely
affect backup times.

The directives that you can use in the file list for a FlashBackup class are:
NEW_STREAM
CACHE=value (see “File List and Cache” earlier in this chapter)
UNSET

Chapter 3, Configuration 15
File List and Cache

UNSET_ALL
For FlashBackup classes, the NEW_STREAM directive must be the first line of the file list.
This directive causes the following to occur:
◆ The backup is split into a separate stream at each point in the file list where the
NEW_STREAM directive occurs.
◆ All file paths between NEW_STREAM directives are in the same stream.
◆ The end of a stream is defined by the start of a new stream (that is, another
NEW_STREAM directive) or the end of the file list.
For example, consider the file lists below:

On Solaris systems: On HP-UX systems:

NEW_STREAM NEW_STREAM
CACHE=/dev/rdsk/c1t3d0s3 CACHE=/dev/cache_group/rvol1c
/dev/rdsk/c1t0d0s6 /dev/vol_grp/rvol1
NEW_STREAM NEW_STREAM
/dev/rdsk/c1t1d0s1 UNSET CACHE
NEW_STREAM CACHE=/dev/cache_group/rvol2c
UNSET CACHE /dev/vol_grp/rvol2
CACHE=/dev/rdsk/c1t3d0s4 NEW_STREAM
/dev/rdsk/c1t2d0s5 UNSET CACHE
/dev/rdsk/c1t5d0s0 CACHE=/dev/cache_group/rvol3c
NEW_STREAM /dev/vol_grp/rvol3
UNSET CACHE /dev/vol_grp/rvol3a
CACHE=/dev/rdsk/c0t2d0s3 NEW_STREAM
/dev/rdsk/c1t6d0s1 UNSET CACHE
CACHE=/dev/cache_group/rvol4c
/dev/vol_grp/rvol4

This file list produces four backups:

◆ The first NEW_STREAM directive starts a backup for /dev/rdsk/c1t0d0s6 (Solaris)
or /dev/vol_grp/rvol1 (HP-UX). The CACHE= entry sets the cache partition to
/dev/rdsk/c1t3d0s3 (Solaris) or /dev/cache_group/rvol1c (HP-UX).
◆ The second NEW_STREAM directive starts a second stream to back up
/dev/rdsk/c1t1d0s1 (Solaris) or /dev/vol_grp/rvol2 (HP-UX). On Solaris
systems, this backup uses the same cache partition. On HP-UX systems, a different
cache partition must be defined for each stream (CACHE=/dev/cache_group
/rvol2c).

16 NetBackup FlashBackup System Administrator’s Guide

 Schedules

◆ The third NEW_STREAM starts a backup for /dev/rdsk/c1t2d0s5 and

/dev/rdsk/c1t5d0s0 (Solaris) or /dev/vol_grp/rvol3 and
/dev/vol_grp/rvol3a (HP-UX). These two partitions are backed up serially
within the stream. In addition, the UNSET CACHE directive unsets the previous cache
setting and the CACHE= directive sets a new cache partition for this backup.
◆ The last NEW_STREAM directive starts a backup for /dev/rdsk/c1t6d0s1 (Solaris)
or /dev/vol_grp/rvol4 (HP-UX). Like the third stream, this one also unsets the
cache directive and defines a new cache partition.
As shown in the example, class-specific directives such as CACHE are passed to the client
with the current stream and all subsequent streams, until the directive is redefined or
unset.
If the directive is encountered again, its value is redefined.
An UNSET or UNSET_ALL directive unsets a directive that was previously defined in the
file list.
◆ UNSET unsets a class-specific directive so it is not passed with additional streams. The
directive that was unset can be defined again later in the file list so it is included in the
current or a later stream.
◆ UNSET_ALL has the same effect as UNSET but affects all class-specific directives that
have been defined up to this point in the file list. If used, UNSET_ALL must appear
directly after the second or later NEW_STREAM keyword.
For more information on Allow multiple data streams, see the NetBackup System
Administrator’s Guide - UNIX.

Schedules
FlashBackup supports only full and incremental schedule types. User backup and archive
schedule types are not allowed.

General Configuration

Client Read Timeout Setting

If the file system being backed up is very large and has a very large number of files, the
default CLIENT_READ_TIMEOUT setting can cause a backup to fail with a status code of
41. A large number of concurrent data streams being active at the same time can also cause
this failure.

Chapter 3, Configuration 17
General Configuration

To avoid or correct this problem, add CLIENT_READ_TIMEOUT to the

/usr/openv/netbackup/bp.conf file on the server and set it to a higher value (the
NetBackup default is 300 seconds). The best value depends on the file system size,
number of files, and system activity.

18 NetBackup FlashBackup System Administrator’s Guide

Using FlashBackup 4
The following topics are covered in this chapter:
◆ Performing a Backup
◆ Performing a Server-Directed Restore
◆ Performing a Client-Directed Restore
◆ Troubleshooting

Performing a Backup

Automatic Backup of a FlashBackup Class

The most convenient way to back up raw partitions with FlashBackup is to configure a
FlashBackup class and then set up schedules for automatic, unattended backups. To add
new schedules or change existing schedules for automatic backups, follow the guidelines
in the NetBackup System Administrator’s Guide - UNIX.

Manual Backup of a FlashBackup Class

The administrator can use the NetBackup Administration interface on the master server to
execute a backup for a FlashBackup class. See the NetBackup System Administrator’s Guide -
UNIX for instructions.

19
Performing a Server-Directed Restore

Performing a Server-Directed Restore

As root user on the master server, you can perform a server-directed restore to a client.
Using the server’s NetBackup Administration interface, you can restore individual
directories or files (or an entire raw partition) backed up by FlashBackup. The procedure
is the same as that for restoring from a regular file system backup as described in the
NetBackup User’s Guide - UNIX. However, note the following before starting the restore.

Note on Restoring Individual Directories or Files

◆ In order to restore individual directories or files from a raw partition backup, the
client must be in a FlashBackup Auspex-FastBackup class and the server must be
configured to allow for individual file restores from raw partition backups.

Notes on Restoring Raw Partitions

◆ To restore a raw partition, you must have administrator capabilities on the NetBackup
server.
◆ An entire raw partition can only be restored from a full backup. FlashBackup and
Auspex-FastBackup incremental backups only support individual file restores.
(NetBackup does not distinguish between full and incremental backups when
performing a standard raw partition backup.)
◆ Ensure that the partition is not mounted and not in use (if the partition is being used
by a database, make sure to shut down the database). The partition must be the same
size as when it was backed up. Otherwise, the results of the restore are unpredictable.
◆ Ensure that the device file for the raw partition exists prior to the restore.
◆ The overwrite option is ignored during raw partition restores. The device file must
exist and the disk partition is overwritten whether this option is set or not.
◆ To avoid overwriting the entire partition, use the alternate-path restore feature to
restore the raw partition to another raw partition of the same size, and then copy
individual files to the original file system.

Performing a Client-Directed Restore

You can use the NetBackup xbp user interface on a FlashBackup client to restore
individual directories or files (or an entire raw partition) from a FlashBackup backup, as
follows.

20 NetBackup FlashBackup System Administrator’s Guide

 Performing a Client-Directed Restore

To Restore Individual Directories or Files with xbp

1. Start xbp. For example, execute:

/usr/openv/netbackup/bin/xbp

2. In the Directory to Search field, specify the file path.

3. On the File menu, click Browse backups (restore).

Note Do not choose Browse backups (restore raw partitions) or Browse backups (Auspex
FastBackup raw partition).

4. In the Backup Images pane, select the desired FlashBackup backup and update the
display (choose Update Display on the Edit menu).
The list of directories and files appears in the Directory Structure and Files panes in
the same way as if you had chosen a regular file system backup.

5. Select the desired directory or files.

To Restore an Entire Raw Partition with xbp

Note To restore an entire raw partition, select a FlashBackup full backup. You cannot
restore the partition from FlashBackup incremental backups because those
incrementals support only individual file restores.

1. Start xbp. For example, execute:

/usr/openv/netbackup/bin/xbp

2. In the Directory to Search field, specify the raw partition.

Specify the device file name (for example, /dev/rdsk), not the file system name.

3. On the File menu, click Browse backups (restore raw partitions).

Note Do not choose Browse backups (Auspex FastBackup raw partition).

4. In the Backup Images pane, select the desired FlashBackup full backup and update
the display (choose Update Display on the Edit menu).
The list of device paths appears in the Directory Structure and Files panes.

5. Select the desired directory or device paths and start the restore.

Chapter 4, Using FlashBackup 21

Troubleshooting

Troubleshooting
This section addresses issues and problems encountered when using FlashBackup.

Gathering Information and Checking Logs

You can resolve many problems on your own by setting up the appropriate logs,
reproducing the problem, and then checking the logs.
◆ To create more log information, put VERBOSE in the bp.conf file on the NetBackup
master and client.

Note The directories under /usr/openv/netbackup/logs can eventually require a lot

of disk space, so delete them when you are finished troubleshooting.

◆ Backup Messages
During a backup, FlashBackup messages are logged to the bpbkar activity log directory
on the client: /usr/openv/netbackup/logs/bpbkar. If necessary, create this
directory (use access mode of 777 so the client can write to the logs).
◆ Restore Messages
During a restore, FlashBackup messages are logged to the bprd activity log directory on
the master server: /usr/openv/netbackup/logs/bprd. If necessary, create this
directory (use access mode of 777 so the client can write to the logs).
◆ snapctl Driver Messages
Messages from the snapctl driver are logged in the client’s /var/adm/messages file
along with other kernel messages.

Before Contacting VERITAS Customer Support

Before calling customer support, please gather as much log information as possible. Be
sure to have the following information ready:
◆ NetBackup version
◆ Operating system version of the FlashBackup client
◆ Note whether or not the action that failed had ever worked, and whether the problem
is repeatable
◆ Log information (see “Gathering Information and Checking Logs” on page 22)
For the customer support phone number, refer to the preface.

22 NetBackup FlashBackup System Administrator’s Guide

 Troubleshooting

Particular FlashBackup Problems

Some of the following items pertain only to Solaris-based systems, as noted.

On Solaris: the backup failed with status code 12

This error can occur if the snap driver is not installed. Make sure that the following files
exist on the client.

32-bit system 64-bit system

/usr/kernel/drv/snapctl.conf /usr/kernel/drv/snapctl.conf
/usr/kernel/drv/snapctl /usr/kernel/drv/sparcv9/snapctl

If the snap driver files do not exist, install the snap driver as described in Chapter 2 on
page 11.

The /tmp directory on the FlashBackup client or server filled up during a

backup
Prior to the 3.4 release of FlashBackup, FlashBackup created temporary files in the /tmp
directory on the client and server during backups and restores. The temporary files are
deleted when the backup or restore is finished.
To change the default location for these files from /tmp to any other directory, you can
create a symbolic link called BPFSMAP_TMPDIR or SFR_TMPDIR that points to a
directory with more space.
To change the directory on the client, execute the following:
cd /usr/openv/netbackup
ln -s /fb_tmp_dir BPFSMAP_TMPDIR
where fb_tmp_dir is the directory where you want FlashBackup to create its temporary
files.
To change the directory on the server, execute the following:
cd /usr/openv/netbackup
ln -s /fb_tmp_dir SFR_TMPDIR
With the 3.4 release, the default location of the temporary files changed to
/usr/openv/BPFSMAP_TMPDIR and /usr/openv/SFR_TMPDIR. This prevents
problems that might result if the /tmp directory filled up.
To change the location of these temporary files, remove the following:
/usr/openv/netbackup/BPFSMAP_TMPDIR

Chapter 4, Using FlashBackup 23

Troubleshooting

/usr/openv/netbackup/SFR_TMPDIR
and enter the commands listed above for the server or client, specifying a different
directory for fb_tmp_dir.

Status code 13 occurs during backups

This status can result from any of the following:
◆ The FlashBackup client may have run out of space in /tmp. If this occurred, you
should see a message such as the following in your bptm log:
16:58:44 [8467] <32> bpfsmap: flush_imebuf: write to tmp inomap
file failed errno=28
Note that errno 28 is ENOSPC, “No space left on device.”
You need to change the default location for the FlashBackup temporary files from
/tmp to a directory with more space. To do so, refer to the instructions under “The
/tmp directory on the FlashBackup client or server filled up during a backup” on
page 23.
◆ The FlashBackup cache partition may have run out of space. In that case, the cache
partition may not be large enough for the backup requirements.
If the cache partition is full, you will see messages such as the following in the system
log:
WARNING: sn_alloccache: cache /dev/vx/rdsk/flash1dg/f full - all
snaps using this cache are now unusable
WARNING: sn_failsnap: snapshot id 5 failed error 28
Specify a larger cache partition, or designate additional cache partitions in the file list.
See Chapter 3 in this guide for cache partition requirements.
◆ On Solaris: If your cache partition runs out of space, there may be “stale” snapshots
taking up space on the cache partition. Stale snapshots are those that were not
automatically deleted by FlashBackup.

a. Determine if there are stale snapshots on your Solaris client by executing the
following:
/usr/openv/netbackup/bin/driver/snaplist

b. For each snapshot listed, execute the following to make sure there is a bpbkar
process associated with it:
ps -eaf |grep ident
where ident is the snapshot process id displayed by the snaplist command.

24 NetBackup FlashBackup System Administrator’s Guide

 Troubleshooting

c. Remove snapshots that do not have an associated bpbkar process by entering the
following:
/usr/openv/netbackup/bin/driver/snapoff snapn
where snapn is the snapshot id displayed by the snaplist command.
◆ On Solaris: The snap.c component of the snap driver snapctl must be at version
1.22 or higher. Earlier versions of this file could cause the backup to fail with status
code 13.
Execute the following to determine the version of the snap.c component of
snapctl.
cd /usr/kernel/drv
strings snapctl |grep Revision
If snap.c is at an earlier version than 1.22, you have a pre-release version of the
product and must install the official release version.

The restore failed with status code 5 after a NetBackup patch was installed
If you receive status code 5 when attempting to restore a FlashBackup file after a
NetBackup patch was installed, the patch may not have been installed properly. Follow
the installation instructions in the patch README file and make sure the libsfr.so file
is copied as instructed.

On Solaris: The backup failed with status code 6, with an ’insane directory
entry’ message in the bpbkar log file
To avoid this error, the snap.c component of the snap driver snapctl must be at version
1.22 or higher. Earlier versions of this file could cause the backup to fail with status code 6
and ’insane directory entry’ messages in the bpbkar log.
Execute the following to determine the version of the snap.c component of snapctl.
cd /usr/kernel/drv
strings snapctl |grep Revision
If snap.c is at an earlier version than 1.22, you have a pre-release version of the product
and must install the official release version.

Client is not updated after the update_flashclients script is run

If the update_flashclients script is run directly from the /usr/openv/
netbackup/bin directory, the files may not be properly updated on the client. In this
case, note the following.

Chapter 4, Using FlashBackup 25

Troubleshooting

◆ If this is a new installation, the update_flashclients log file in /tmp will contain
the following entry:
Couldn’t execute sh /usr/openv/netbackup/bin/extract.sh>/dev/null
2>/dev /null on duo
◆ If update_flashclients is being used to install a patch and
update_flashclients is run from the /usr/openv/netbackup/bin directory,
the files will not be updated on the client but there will be no indication of a failure in
the log file.
If you are having this problem, make sure to run the update_flashclients script from
the / (root) directory.

System crashed after installing a NetBackup patch

If a patch is installed on the NetBackup server, but the update_flashclients script
did not complete successfully on the FlashBackup client, inconsistencies between binaries
can cause a system crash. If you have installed a patch on the NetBackup server, make
sure the update_flashclients script completed successfully on the client.

On HP-UX: the backup failed with status code 20

The HP-UX VxFS snapshot mechanism requires a dedicated cache partition for each
snapshot. A check is made in the mount table to make sure the cache partition is not
already in use. If the cache partition is already in use, status code 20 will occur.
Check the /usr/openv/netbackup/logs/bpbkar log for a message similar to the
following:
bpfsmap: FTL - bpfsmap: snapshot cache already in use, /dev/arrayvg/vol4c
bpbkar Exit: ERR - bpbkar FATAL exit status = 20: invalid command parameter
bpbkar Exit: INF - EXIT STATUS 20: invalid command parameter
If the snapshot cache partition is already in use, you will have to set up your class
schedules to run at different times, or use different cache partitions for each backup.
If the Allow multiple data streams option is enabled, each stream must have its own
dedicated cache partition.

26 NetBackup FlashBackup System Administrator’s Guide

Solaris snapctl Driver A
Under normal conditions, the snap driver is invoked only by NetBackup.
Each FlashBackup backup requires that a cache partition be specified in the class file list
by using a CACHE= entry (see “File List and Cache” on page 14). On Solaris systems, the
same cache can be used by any number of concurrent backups, as long as it is big enough.
For HP-UX systems, each concurrent backup must have a dedicated cache partition.
The cache size should be approximately 10% to 15% of the total of all partitions that are
associated with the specific cache. This assumes no more than a moderate level of write
activity during backups.
If a cache overflows, all snapshots that are using the cache will become unreadable and
the backups that are reading the snapshots will fail.

Command Usage

snapoff
snapoff terminates a snapshot that was previously initiated by a backup that failed
abnormally. snapoff must be invoked as:
/usr/openv/netbackup/bin/driver/snapoff snap1 ... snapn

27
Command Usage

If snapoff is successful, a message of the following form will be displayed:

snap 1 disabled
snap 2 disabled
...
snap n disabled
If snapoff fails, an explanatory message is displayed. Error codes are identified in
/usr/include/sys/errno.h.

snaplist
This command must be invoked as:
/usr/openv/netbackup/bin/driver/snaplist
snaplist displays information about all active snapshots in the following form:
id device size cached cache err time
1 /dev/rdsk/c0t3d0s0 72560 16450 /dev/rdsk/c0t4d0s0 0 12/19/99 13:23:48

Where:
◆ size is the size of the snapped partition in 512-byte blocks.
◆ cached is the number of 512-byte blocks that have been cached (written to) for this
snapshot since it was initiated.
◆ err is an error code; 0 indicates no error.
If a snapshot has encountered an error, then err will be non-zero and the snapshot
will be inaccessible. It can be terminated using snapoff. Error codes are identified in
/usr/include/sys/errno.h. Also, error messages may be found in
/var/adm/messages.

snapcachelist
This command must be invoked as:
/usr/openv/netbackup/bin/driver/snapcachelist
snapcachelist displays information about all partitions currently in use as snapshot
caches. It is useful for monitoring the extent to which caches are full. Displayed output is
of the form:
device free busy
/dev/rdsk/c0t4d0s0 238528 264472
Where:
◆ free is the number of 512-byte blocks available.

28 NetBackup FlashBackup System Administrator’s Guide

 Command Usage

◆ busy is the number of 512-byte blocks that have been written to.
When a cache is full, any write to a snapped partition or snapped file system associated
with that cache will cause the snapshot to fail and the snapshot will no longer be readable
or writable. Reads or writes to the snapped partition will remain unaffected. The failed
snapshot will not be terminated automatically and must be terminated using snapoff in
the usual way.

Note Snapshots used by the FlashBackup mechanism in NetBackup are initiated and
terminated by NetBackup. While a FlashBackup backup is in progress, snaplist
and snapcachelist can be used to monitor the snapshot.

Caution Do not terminate a NetBackup snapshot using snapoff because corruption of

the backup image may result.

snapstat
The snapstat command must be invoked as:
/usr/openv/netbackup/bin/driver/snapstat
snapstat displays diagnostic information about the snap driver.

Appendix A, Solaris snapctl Driver 29

Command Usage

30 NetBackup FlashBackup System Administrator’s Guide

Index
A F
Allow multiple data streams 15, 26 file
Auspex FastBackup restore 20 backup 19
restore
B
individual files 4, 21
backup
raw partition 21
automatic 19
file list 14
image 5
FlashBackup features 2
manual 19
types supported 17 G
bpbkar 5 general class attributes 13
log 22, 25
H
process 24
HSM 2
bpbrm 5
bpdbm 7 I
BPFSMAP_TMPDIR 23 ifrfr (individual file restore from raw) 4
bprd activity log 22 insane directory entry message 25
bptm 5, 7 installation
log 24 distribute to clients 10
install FlashBackup 9
C
install snap driver 11
cache 14
prerequisites 9
partition 26
supported platforms 9
partition (out of space) 24
uninstalling 12
cache partition (out of space) 24
CACHE= entry 14 L
checking logs 22 libbpfsmap.sl (HP) 5
class attributes, general 13 libbpfsmap.so (Solaris) 5
client list 14 libsfr.so file 25
CLIENT_READ_TIMEOUT 17 logs 22
configuration M
client list 14 manuals
file list and cache 14 audience vii
general class attributes 13 related vii
customer support 22 multiple data streams option 15, 26
D O
deinstallation 12 overwriting
raw partition restores 20

31
 P driver log 22
patch, troubleshooting 25, 26 file 23
performance 3 overview 27
snaplist command 28
R
snapoff command 27
raw partition
snapshot 2
backup 19
cache partition 26
client-directed restore 21
on Solaris client, troubleshooting 24
server-directed restore 20
snapstat command 29
reliability 2
streams, allow multiple data 15
restore
supported platforms 9
client-directed 21
symbolic links 23
individual files 4, 21
overwrite option 20 T
re. device file 20 technical overview 4
server-directed 20 temporary files (/tmp directory) 23, 24
restrictions 3 troubleshooting 22
types of backups supported 17
S
sfr 6 U
SFR_TMPDIR 23 UNSET 17
shared libraries 5 UNSET_ALL 17
snap driver update_flashclients script 25, 26
installation 11
V
not installed 23
VERBOSE setting for logs 22
snap.c component of snapctl 25
snapcachelist command 28 X
snapctl xbp 21
.conf file 23

32 NetBackup FlashBackup System Administrator’s Guide