Scribd
Upload
224 views2 pages

Parasitic Battery Draw

The document discusses parasitic battery draw, which refers to electrical devices that continue to draw current from the battery when the ignition is off. A normal parasitic draw is below 50 milliamps. Before testing, the battery should be over 75% charged. Safety precautions for working with batteries include wearing eye protection, avoiding open flames, and only charging in ventilated areas due to hydrogen gas. To test for parasitic draw, connect a digital amp meter capable of reading milliamps to the battery after turning accessories off and the ignition to off. The reading will initially be high as devices power up, then stabilize in the milliamp range indicating the vehicle's parasitic draw. If excessive, circuits can be isolated by removing fuses one

Uploaded by

Rishelle Snow
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
224 views2 pages

Parasitic Battery Draw

The document discusses parasitic battery draw, which refers to electrical devices that continue to draw current from the battery when the ignition is off. A normal parasitic draw is below 50 milliamps. Before testing, the battery should be over 75% charged. Safety precautions for working with batteries include wearing eye protection, avoiding open flames, and only charging in ventilated areas due to hydrogen gas. To test for parasitic draw, connect a digital amp meter capable of reading milliamps to the battery after turning accessories off and the ignition to off. The reading will initially be high as devices power up, then stabilize in the milliamp range indicating the vehicle's parasitic draw. If excessive, circuits can be isolated by removing fuses one

Uploaded by

Rishelle Snow
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Parasitic Battery Draw

The term parasitic battery draw refers to the electrical devices that continue to draw
current from the battery when the ignition key is in the OFF position. As a rule of thumb
normal parasitic draws are below 50 milliamps, however it is always best to refer to the
original vehicle manufacturers specifications for recommended limits. Before a parasitic
draw test can be performed the batteries state of charge must be greater than 75%.

Safety

Before testing a battery it is very important to follow some simple safety rules.
Always wear eye protection and keep open flames away from the battery. If using a
battery charger, always confirm that the charger is off before connecting or
disconnecting the charger. Batteries produce hydrogen gas which is extremely
flammable; do not smoke while servicing a battery. Batteries should only be charged
in well ventilated areas. The electrolyte in the battery contains sulfuric acid, latex
gloves are highly recommended.

Testing For Parasitic Draw

To perform the parasitic draw test you will need a digital amp meter capable of
reading milliamps and a minimum of 10 amps. Be certain that your meter has a fuse
intended to protect the meter for the rare occurrence of an abnormally high amp
draw.

1. Insure that all accessories are off and the ignition switch is in the OFF position.

2. Remove the negative battery cable from the battery.

3. Set amp meter switch to the highest rating (10 amps or higher).

4. Connect amp meter as illustrated in figure 1.


FIGURE 1

5. The reading may start as high as 6 amps, this is normal. When the battery cable was
disconnected the vehicles electronics lost power, these devices will draw a higher
current when they are reconnected. The current will drop as the numerous electronic
devises “awaken”. On some late model vehicles this may take 20 minutes or longer.

6. As the reading decreases and stabilizes adjust the amp meter down to read in the
milliamp range. This reading will be the vehic les parasitic draw.

High Parasitic Reading

Should you determine that the parasitic draw exceeds the vehicles limit it will be
necessary to determine the circuit that is creating the draw. This is best accomplished
by using the process of elimination. Check lamp circuits (glove box, courtesy, trunk etc.)
for bulbs that are illuminated when they should be off. To check the trunk lamp it may
be necessary to get in the trunk. Make certain that you have a helper. And more
importantly make certain that your helper is your friend!

If a visual inspection fails, isolate circuits by removing fuses one at a time while noting
amp reading. Once you have identified the circuit, refer to the service manual or wiring
diagram to determine which devises are on the circuit. Disconnect the devices to
determine which is faulty. It may also be necessary to disconnect relays or non fused
circuits. It is simply a process of elimination at this point.

You might also like