Scribd
Upload
124 views

Adsorption: Ion Exchange Is A Similar Process However, in This Case Ions Create Complexes With The Solid

Adsorption is a process where a component selectively attaches to the surface of a solid adsorbent, allowing separation from mixtures. Common adsorbents include activated carbon, silica gel, and zeolites. In adsorption processes, the mixture passes through a fixed bed of adsorbent particles where the component attaches to pore walls. When the bed reaches saturation, it is regenerated to desorb the component for recovery and reuse of the adsorbent.

Uploaded by

madhujayaraj
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
124 views

Adsorption: Ion Exchange Is A Similar Process However, in This Case Ions Create Complexes With The Solid

Adsorption is a process where a component selectively attaches to the surface of a solid adsorbent, allowing separation from mixtures. Common adsorbents include activated carbon, silica gel, and zeolites. In adsorption processes, the mixture passes through a fixed bed of adsorbent particles where the component attaches to pore walls. When the bed reaches saturation, it is regenerated to desorb the component for recovery and reuse of the adsorbent.

Uploaded by

madhujayaraj
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Adsorption

A component can be separated from a mixture if it selectively adsorbs onto a solid surface. This
is the basis of the adsorption unit process. Adsorbents are usually porous solids, and adsorption
occurs mainly on the pore walls "inside" particles. Examples of adsorbents include:

 activated carbon (adsorbs organics)


 silica gel (adsorbs moisture)
 activated alumina (adsorbs moisture)
 zeolites and molecular sieves
 synthetic resins

Ideally, one would be able to construct a continuous countercurrent system, but moving solids is
tricky. Instead, most commercial applications use small particles of adsorbent in a fixed bed.
Fluid passes down through the bed (down instead of up to avoid fluidization) and components
adsorb onto the solid. The steps can be summarized:

1. solute diffuses through the fluid to an area near the solid particle surface
2. solute diffuses into the pores of the particle
3. solute diffuses to the pore wall
4. solute adsorbs to the pore wall surface

Ion exchange is a similar process; however, in this case ions create complexes with the solid
instead of adsorbing.

When a bed nears saturation, the flow is stopped and the bed is regenerated to cause desorption.
The adsorbate can thus be recovered and the adsorbent reused. Regeneration can be
accomplished in several ways, and these lead to the "cycle type":

 Temperature swing
 Pressure swing
 Inert/Purge stripping
 Displacement Purge

Temperature swing is usually the slowest of these (since the bed has to heat/cool before reuse).

Adsorption Equilibrium

Adsorption equilibrium data is typically


plotted in the form of an adsorption isotherm
(i.e. at constant temperature) with the mass
adsorbed on the y-axis and the mass in the
fluid on the x-axis. The shape of the curve is
significant and factors heavily into design.
"Favorable" isotherms permit higher solid
loadings at lower solution concentrations. These tend to start out steep and level out. Isotherms
which start out flat are "unfavorable", since they only work well at high concentrations of solute.
Usually, as temperature increases the amount adsorbed decreases (permitting thermal
regeneration).

Several fits have been proposed for isotherms. A linear isotherm seems to work for very dilute
solutions, but not for many others. The Freundlich isotherm describes physical adsorption from
liquids and can also be used for the adsorption of hydrocarbon gases on activated carbon. It is a
two parameter model, of the form

Maybe the best known is the Langmuir isotherm, given by

which assumes that the number of adsorption sites is fixed and that adsorption is reversible.

Breakthrough Curves

Adsorption is a transient process. The amount of material adsorbed within a bed depends both on
position and time. Consider the time dependence. As fluid enters the bed, it comes in contact
with the first few layers of absorbent. Solute adsorbs, filling up some of the available sites. Soon,
the adsorbent near the entrance is saturated and the fluid penetrates farther into the bed before all
solute is removed. Thus the active region shifts down through the bed as time goes on.

The fluid emerging from the bed will have little or no


solute remaining -- at least until the bulk of the bed
becomes saturated. The break point occurs when the
concentration of the fluid leaving the bed spikes as
unadsorbed solute begins to emerge. The bed has become
ineffective. Usually, a breakpoint composition is set to be
the maximum amount of solute that can be acceptably lost,
typically something between 1 and 5 percent.

As the concentration wave moves through the bed, most of


the mass transfer is occurring in a fairly small region. This
mass transfer zone moves down the bed until it "breaks
through". The shape of the mass transfer zone depends on the adsorption isotherm (equilibrium
expression), flow rate, and the diffusion characteristics. Usually, the shape must be determined
experimentally.
The wave front may change shape as it moves through
the bed, and the mass transfer zone may broaden or
diminish. Unfavorable and linear isotherms tend to
broaden. Favorable Langmuir and Freundlich
isotherms may broaden at first, but quickly achieve a
constant pattern front, an asymptotic shape. This
means that the mass transfer zone is constant with
respect to both position and time. When dealing with a
constant pattern front, one can make measurements on
a small scale apparatus and scale-up the results to a
full-size adsorber bed.

You might also like