SI Unit rules and style conventions

Check List for Reviewing Manuscripts

#1 Only units of the SI and those units recognized for use with the SI are used to
General express the values of quantities. Equivalent values in other units are given in
parentheses following values in acceptable units only when deemed necessary for
the intended audience.

#2 Abbreviations such as sec, cc, or mps are avoided and only standard unit symbols,
Abbreviati prefix symbols, unit names, and prefix names are used.
ons
proper: s or second; cm3 or cubic centimeter; m/s or meter per second
improper: sec; cc; mps

#3 Unit symbols are unaltered in the plural.

Plurals
proper: l = 75 cm
improper: l = 75 cms

#4 Unit symbols are not followed by a period unless at the end of a sentence.
Punctuati
proper: The length of the bar is 75 cm.
on
The bar is 75 cm long.
improper: The bar is 75 cm. long.

#5 A space or half-high dot is used to signify the multiplication of units. A solidus

Multiplica (i.e., slash), horizontal line, or negative exponent is used to signify the division of
tion units. The solidus must not be repeated on the same line unless parentheses are
& division used.
proper: The speed of sound is about 344 m·s-1 (meters per second)
The decay rate of 113Cs is about 21 ms-1 (reciprocal
milliseconds)
m/s, m·s-2, m·kg/(s3·A), m·kg·s-3·A-1
m/s, m s-2, m kg/(s3 A), m kg s-3 A-1
improper: The speed of sound is about 344 ms-1 (reciprocal
milliseconds)
The decay rate of 113Cs is about 21 m·s-1 (meters per second)
m ÷ s, m/s/s, m·kg/s3/A

#6 Variables and quantity symbols are in italic type. Unit symbols are in roman type.
Typeface Numbers should generally be written in roman type. These rules apply irrespective
of the typeface used in the surrounding text. For more details, see Typefaces
for symbols in scientific manuscripts
proper: She exclaimed, "That dog weighs 10 kg!"
t = 3 s, where t is time and s is second
T = 22 K, where T is thermodynamic temperature, and K is
kelvin
improper: He exclaimed, "That dog weighs 10 kg!
t = 3 s, where t is time and s is second
T = 22 K, where T is thermodynamic temperature, and K is
kelvin
#7 Superscripts and subscripts are in italic type if they represent variables, quantities,
Typeface or running numbers. They are in roman type if they are descriptive.
subscript category typeface proper usage
quantity italic cp, specific heat capacity at constant pressure
descriptive roman mp, mass of a proton
running number italic

#8 The combinations of letters "ppm," "ppb," and "ppt," and the terms part per million,
Abbreviati part per billion, and part per trillion, and the like, are not used to express the values
ons of quantities.
proper: 2.0 µL/L; 2.0 x 10-6 V;
4.3 nm/m; 4.3 x 10-9 l;
7 ps/s; 7 x 10-12 t,
where V, l, and t are the quantity symbols for volume, length,
and time.
improper: "ppm," "ppb," and "ppt," and the terms part per million, part
per billion, and part per trillion, and the like

#9 Unit symbols (or names) are not modified by the addition of subscripts or other
Unit information. The following forms, for example, are used instead.
modificati
proper: Vmax = 1000 V
ons
a mass fraction of 10 %
improper: V= 1000 Vmax
10 % (m/m) or 10 % (by weight)

#10 The symbol % is used to represent simply the number 0.01.

Percent
proper: l1 = l2(1 + 0.2 %), or
D = 0.2 %,
where D is defined by the relation D = (l1 - l2)/l2.
improper: the length l1 exceeds the length l2 by 0.2 %

#11 Information is not mixed with unit symbols or names.

Informa
proper: the water content is 20 mL/kg
tion
& units improper: 20 mL H2O/ kg
20 mL of water/ kg

#12 It is clear to which unit symbol a numerical value belongs and which mathematical
Math operation applies to the value of a quantity.
notatio
proper: 35 cm x 48 cm
n
1 MHz to 10 MHz or (1 to 10) MHz
20 °C to 30 °C or (20 to 30) °C
123 g ± 2 g or (123 ± 2) g
70 % ± 5 % or (70 ± 5) %
240 x (1 ± 10 %) V
improper: 35 x 48 cm
1 MHz-10 MHz or 1 to 10 MHz
 20 °C-30 °C or 20 to 30 °C
123 ± 2 g
70 ± 5 %
240 V ± 10 % (one cannot add 240 V and 10 %)

#13 Unit symbols and unit names are not mixed and mathematical operations are not
Unit applied to unit names.
symbol
proper: kg/m3, kg · m-3, or kilogram per cubic meter
s
& names improper: kilogram/m3, kg/cubic meter, kilogram/cubic meter, kg per m3, or
kilogram per meter3.

#14 Values of quantities are expressed in acceptable units using Arabic numerals and
Numera symbols for units.
ls &
proper: m = 5 kg
unit
the current was 15 A
symbols
improper: m = five kilograms
m = five kg
the current was 15 amperes

#15 There is a space between the numerical value and unit symbol, even when the value is
Unit used in an adjectival sense, except in the case of superscript units for plane angle.
spacing
proper: a 25 kg sphere
an angle of 2° 3' 4"
If the spelled-out name of a unit is used, the normal rules of English
apply: "a roll of 35-millimeter film."
improper: a 25-kg sphere
an angle of 2 ° 3 ' 4 "

#16 The digits of numerical values having more than four digits on either side of the
Digit decimal marker are separated into groups of three using a thin, fixed space counting
spacing from both the left and right of the decimal marker. Commas are not used to separate
digits into groups of three.
proper: 15 739.012 53
improper: 15739.01253
15,739.012 53

#17 Equations between quantities are used in preference to equations between numerical
Quantit values, and symbols representing numerical values are different from symbols
y representing the corresponding quantities. When a numerical-value equation is used, it
equatio is properly written and the corresponding quantity equation is given where possible.
ns
proper: (l/m) = 3.6-1 [v/(km/h)](t/s)
improper: l = 3.6-1 vt, accompanied by text saying,
"where l is in meters, v is in kilometers per hour, and t is in seconds"

#18 Standardized quantity symbols are used. Similarly, standardized mathematical signs
Standar and symbols are used. More specifically, the base of "log" in equations is specified
d when required by writing loga x (meaning log to the
symbol base aof x), lb x (meaning log2 x), ln x (meaning loge x), or lg x (meaning log10 x).
s
proper: tan x
 R for resistance
Ar for relative atomic mass
improper: tg x for tangent of x
words, acronyms, or ad hoc groups of letters

#19 When the word "weight" is used, the intended meaning is clear. (In science and
Weight technology, weight is a force, for which the SI unit is the newton; in commerce and
vs. everyday use, weight is usually a synonym for mass, for which the SI unit is the
mass kilogram.)

#20 A quotient quantity is written explicitly.

Quotien
proper: mass divided by volume
t
quantit improper: mass per unit volume
y

#21 An object and any quantity describing the object are distinguished. (Note the
Object difference between "surface" and "area," "body" and "mass," "resistor" and
& "resistance," "coil" and "inductance.")
quantit
proper: A body of mass 5 g
y
improper: A mass of 5 g

#22 The obsolete terms normality, molarity, and molal and their symbols N, M, and m are
Obsolet not used.
e
proper: amount-of-substance concentration of B (more commonly called
Terms
concentration of B), and its symbol cB and SI unit mol/m3 (or a
related acceptable unit)
molality of solute B, and its symbol bB or mB and SI unit mol/kg (or a
related unit of the SI)
improper: normality and the symbol N, molarity and the symbol M
molal and the symbol m

Return to Units home page

Online: February 1998 - Last update: September 2004