FOR OFFICE USE ONLY

fcgkj ljdkj

BUILDING CONSTRUCTION DEPARTMENT

Schedule of Rates

VOLUME – 1

(Edition — Eighth)

Effective from 17.10.2016

The standard data Book is for Departmental use only. It cannot be produced in
Court of Law as reference / authority and thus is a privilege document

First Edition : 01.07.2008

Second Edition : 16.01.2009
Third Edition : 24.11.2009
Fourth Edition : 15.06.2011
Fifth Edition : 16.07.2012
Sixth Edition : 11.08.2013
Seventh Edition : 15.09.2014
Eighth Edition : 17.10.2016

BUILDING CONSTRUCTION DEPARTMENT

BIHAR

Published by :

ENGINEER IN CHIEF
BUILDING CONSTRUCTION DEPARTMENT
BIHAR, PATNA
 RATE OF ITEMS
VOLUME-1
Volume Sub-head
Contents/Chapter PAGE N0
Number No.
One Preface i – Lvii
0.1 Basic Rates of Hire Charge of plant (i) 1–2
0.2 Basic Rates of Labour 3–4
0.3 Basic Rates of Building & Road work 5 – 62
0.4 Capacity of truck 63 – 64
01 Carriage of Material 65 – 68
02 Earth Work 69 – 73
03 Mortars 74 – 74
04 Concrete work 75 – 77
05 Reinforced cement concrete 78 – 86
Brick work (A)
Brick work (B)
06 87 – 90
Brick work (C)
Brick work (D)
07 Stone work 91 – 95
08 Marble work 96 – 98
09 Wood work 99 – 124
10 Steel work 125 – 129
11 Flooring 130 – 139
12 Roofing 140 – 146
13 Finishing 147 – 155
14 Repairs to Buildings 156 – 158
15 Dismantling and Demolishing 159 – 164
17 Sanitary Installations 165 – 175
18 Water Supply 176 – 197
19 Drainage 198 – 205
20 Pile work 206 – 208
21 Aluminium Work 209 – 212
22 Water Proofing 213 – 216
23 Horticulture & Landscaping 217 – 219
24 Rain water Harvesting & Tube Wells 220 – 222
25 Conservation of Heritage Building 223 – 224
26 Strutural Glazing and Composite 225 - 230
Aluminium Panel
i BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 ii
iii BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 iv
v BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 vi
vii BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 viii
ix BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 x
xi BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xii
xiii BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xiv
xv BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xvi
xvii BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xviii
xix BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xx
xxi BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xxii
 RAILWAY ROUTE
CHART & FREIGHT
xxiii BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xiv
xxv BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xxvi
xxvii BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xxviii
xxix BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xxx
xxxi BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xxxii
xxxiii BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xxxiv
xxxv BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xxxvi
xxxvii BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xxxviii
xxxix BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xL
xLi BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xLii
xLiii BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xLiv
xLv BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xLvi
xLvii BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 xLviii
xLix BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 L
Li BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 Lii
Liii BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 Liv
Lv BCD/SOR_8th Edition_October 2016
BCD/SOR_8th Edition_October 2016 Lvi
Lvii BCD/SOR_8th Edition_October 2016
 SUB HEAD : 0.1
HIRE CHARGES OF PLANTS
 BASIC RATES - Contd.
0.1 Hire Charges of Plants
Note:- These rates are exclusive of contractor's profit and over head:, nd are inclusive of wages for weekly day of rest
Code Description Unit Rate Rs. As
No per 8th ed
001 Hire charges of Coaltar Boiler 900 to 1400 litres Per day 830.00
002 Hire charges of Concrete Mixer 0.14 cubic metre Per day 800.00
003 Hire charges of Diesel Road Roilei - 8 to 10 tonne Per day 1500.00
004 Production cosr of concrete by batch mix plant. cum 350.00
005 Hire charges of Diesel Truck - 9 tonne Per day 1700.00
006 Hire charges of Spraying machine including electric charges Per day 250.00
007 Hire charges of Coltar Sprayer Per day 300.00
008 Hire charges of Barber green , drying mixing and Asphalt Plant , with Per day 7700.00
accessories .capacity 30/45tonne
009 Pumping charges of concreteincluding Hire charges of pump, piping work & cum 150.00
accessories etc.
010 Hire charges of Derrick monkey rope Per day 800.00
011 Hire charges of Pump set of capacity 4000 litres/hour. Per day 600.00
012 Vibrator (Needle type 40mm) Per day 350.00
013 Machine for rubbing of floors Per day 350.00
014 Front end loader Per day 5000.00
015 Hire and running charges of Tripod and Mechanical Winch machine Per day 6000.00
complete with power unit and accessories
016 Mastic Cooker Per day 750.00
017 Hire and running charges of tipper Per day 1700.00
018 Hue and running charges ol loader Per day 5000.00
019 Hire Grinder for mirror polish Per day 250.00
020 Hydraulic Excavator (3D) with driver and fuel. Per day 8000.00
021 Pin vibrator Per day 350.00
022 Surface Vibrator Per day 400.00
023 Hot Bitumen mixer 0.5 cum i/c hand cart Per day 4000.00
024 Hire and running charges of hydraulic piling no «viih power unit etc. Per day 34000.00
including complete accessories and shifting at site.
025 Hire and running charges of light crane Per day 2200.00
026 Hire and running charges of bentonite pump. Per day 4200.00
027 Hire and running charges of vibrating pile driving hammer complete
with power unit and accessories. Per day 35000.00
028 Hire and running charges of crane 20 tonne capacity Per day 9300.00
029 Carriage of concrete by transit mixer. km/cum 30.00
030 Generator 250 KVA. Per day 2300.00
033 Paint applicator Per day 750.00
037 Mobile crane. Per day 7000.00
038 Tractor with ripper attachment Per day 1350.00
039 Tractor with trolley Per day 1500.00
040 Aircompressor 250 cfm with two leads for pneumatic cutters/hammers Per day 2000.00
041 Joint cutting machine with 2-3 blades Per day 1100.00
042 C.C.batch mix plant. Per day 10000.00
043 Road sweeper Per day 550.00
045 Slip frompaver with sensor. Per day 13000.00
046 Water tanker 5000 litre capacity Per day 1000.00
047 Concrete joint cutting machine Per day 900.00
048 Texturing machine Per day 925.00
Note:- Above hire-charges include cost of service of operating staff and supply of lubricating oil.

1 BCD/SOR_8th Edition_October 2016

 Code Description Unit Rate Rs. As
No per 8th ed
NEW CODES

049 Dozer D-80-A 12 hour 1750.00

050 Motor Grader 3.35 metre blade hour 2450.00
051 Hydraulic Excavator of 1 cum bucket hour 1200.00
052 Front end loader 1 cum bucket capacity (incl POL) hour 900.00
053 Tipper -5 Cum tonne km 3.00
054 Vibratory roller 8 to 10 tonne hour 1300.00
055 Smooth Wheeled Roller 8 to 10 tonne hour 450.00
056 Tandem Road Roller hour 1150.00
057 Water Tanker 5 to 6 KL capacity hour 150.00
058 Air compressor hour 325.00
059 Wet Mix Plant 60 TPH hour 1200.00
060 Mechanical Broom Hydraulic hour 360.00
061 Emulsion Pressure Distributor @ 1750 sqm per hour hour 800.00
062 Hot mix Plant -120 TPH capacity hour 23700.00
063 Hot mix Plant 100 TPH Capacity hour 17500.00
064 Paver finisher Hydrostatic with sensor control 100 TPH hour 2700.00
065 Paver finisher Mechanical 100 TPH hour 1000.00
066 Batching and Mixing Plant @ 75 cum per hour hour 2500.00
068 Concrete Paver finisher with 40 HP Motor and sensor hour 2900.00
069 Generator 250 KVA hour 700.00
070 Generator 100 KVA/125 KVA hour 500.00
071 Truck 5.5 cum/ 10 tonnes tonne km 3.00
075 Road sweeper (Mechamical Broom) @ 1250 sqm per hour hour 360.00
076 Drum Type HMP of 60-90 TPH capacity @ 75 tonne per hour actual output hour 14000.00
080 Hire and running charges of drill machine up to 400 mm dia cost of mobile day 7500.00
oil, diesel consumption in ordinary soil and operator)(including
0081 Pile integrity testing equipment day 3000.00
0082 Excavation of diaphragm wall by mechanical grab sqm 1500.00
0083 Hire charges of TATA 407 or eqivalent fr local shifting day 1300.00

Note :- Above hire - charges (from item code 0049 to 0082) include cost of services of operating staff,
supply of lubricating oil and diesel also.

BCD/SOR_8th Edition_October 2016 2

SUB HEAD : 0.2
LABOUR
 BASIC RATES - Contd.
0.2 LABOUR
Note:- These rates are exclusive of contractor's profit and over heads and are inclusive of wages
for weekly day of rest
Rate As per
Code Lab deptt noti no
Description Unit
No 124/1-04-16
Rs.
0100 Bandhani per day 222.00
0101 Bhishti per day 229.00
0102 Blacksmith 1st class per day 279.00
0103 Blacksmith 2nd class per day 249.00
0107 Bullockman with single builock per day 284.00
0111 Carpenter 1st class per day 279.00
0112 Carpenter 2nd class per day 249.00
0113 Chowkidar per day 220.00
0114 Beldar per day 206.00
0115 Coolie per day 218.00
0116 Fitter (Grade 1) per day 283.00
0117 Assistant Fitter or 2nd class Fitter per day 249.00
0119 Glazier per day 233.00
0122 Mason {For plaster of paris work} 1st class per day 279.00
0123 Mason (for orick work) 1st class per day 279.00
0124 Mason (for brick work) 2nd class per day 249.00
0125 Mason (for plain stone work) 2nd class per day 249.00
0126 Mason (for ornamental stone work) 1st class per day 279.00
0127 Concrete mixer operator Gr 1 per day 265.00
0128 Mate per day 222.00
0129 Mali per day 262.00
0130 Mistry per day 206.00
0131 Painter per day 275.00
0132 Rock Excavator per day 220.00
0133 Rock Breaker per day 220.00
0134 Rock Hole Driller per day 220.00
0135 Stone Chiseller per day 222.00
0136 Sewerman per day 222.00
0138 Sprayman (for bitumen, tar etc.) per day 220.00
0139 Skilled Beldar (for floor rubbing etc.) / Grinder per day 249.00
0141 White Washer per day 262.00
0155 Mason (average) per day 249.00
0156 Carpenter (average) per day 249.00
0157 Operator (Pile/Special machines) per day 354.00
0158 Mechanic (Pile/ Assistant operator) per day 323.00
0159 Skilled Torch Operator per day 262.00
0L01 Un Skilled labour per day 206.00
0L02 Un Skilled labour per day 206.00
0L03 Mistri per day 206.00

3 BCD/SOR_8th Edition_October 2016

 Rate As per
Code Lab deptt noti no
Description Unit
No 124/1-04-16
Rs.
0L04 Cleaner per day 206.00
0L05 Helper per day 206.00
0L06 Khalasi per day 206.00
0L11 Electrician Gr-I per day 265.00
0L11A Electrician Gr-II per day 247.00
0L12 Lineman/wireman per day 243.00
0L13 Chargeman per day 299.00
0L14 Fore man per day 354.00
0L15 Welder Gr I per day 315.00
0L19 Cheker per day 252.00
0L20 Hammerman per day 220.00
0L21 Tin smith per day 284.00
0L22 Tin plate maker per day 299.00
0L25 Tile layer per day 222.00
OL26 Thatcher per day 222.00
0L27 Plumber per day 265.00
0L28 Grader per day 252.00
0L29 Road binder per day 233.00
0L32 Stone layer per day 247.00
0L34 Fire man per day 222.00
0L36 Gas cutter per day 264.00
0L37 Rigger per day 252.00
0L38 Sarang per day 270.00
0L39 Chipper cum riveitew per day 264.00
0L40 Tractor operator per day 299.00
0L43 Vibrator operator per day 232.00
0L44 Pump driver Gr I per day 265.00
0L46 Concrete mixture operator Gr I per day 265.00
0L49 Truck Driver per day 299.00
0L50 Car/Jeep Driver per day 264.00
0L51 Crane Operator Gr 1 per day 354.00
0L52 Winch Operator per day 265.00
0L53 Road Roller Driver per day 361.00
0L56 Polisher per day 222.00
0L70 Any Other category of semi skilled worker not per day 215.00
0L71 Any other category of skilled worker not mentioned per day 262.00
0L72 Highly skilled workers per day 319.00

BCD/SOR_8th Edition_October 2016 4

 SUB HEAD : 0.3
BASIC RATES OF BUILDING &
ROAD WORK
 0.3 MATERIALS FOR BUILDING WORK AND ROAD WORK
Note.- These rates are exclusive of contractor's profit, over heads and carriage but
include octroi (vat and other taxes)
Present
Code No Description Unit
Approved rate
1 2 3 4
0200 Plain ended valley gutters Sheets 6 mm thick (corrugated) sqm 209.81
0204 Curved barge board each 154.00
0205 Barge Board 2.44 metre long each 359.95
0206 Barge Board 1.83 metre long each 269.49
0207 Drop end for plain ended valley gutter One piece plain angular each 155.92
ridge 1 .22 metres long
0208 Plain ended valley gutters Serrated or plain wing Adjustable pair 213.67
Ridge 1.22 m long
0209 Close fittings adjustable ridge 1.10 m long pair 242.54
0210 Drop end for plain ended valley gutter North light adjustable pair 213.67
ridge 1.22 mm long
0211 Plain ended valley gutters Ridge finials pair 109.72
0212 Plain ended valley gutters Unserrated adjustable ridge for hips pair 213.67
0213 Plain ended valley gutters Roof light (1.82 metre long) each 1154.94
0214 Apron flashing pieces each 150.14
0215 Drop end for plain ended valley gutter Eaves filler pieces each 109.72
0216 Drop end for plain ended valiey gutter North iight ventilator each 263.72
curves
0219 Drop end for plain ended valley gutter Expansion joint for North each 161.69
light curves
0220 Drop end for plain ended valley gutter Expansion joint for ridqes pair 302.21
0221 Drop end for plain ended valley gutter Louvers 'S' type (1.75 m) each 127.05
0222 Seam bolts nuts 6mm dia and 25mm long 10 Nos 41.62
0223 Non-Asbestos fibre (high impact poly propelene reinforced) sqm 260.14
cement corrugated sheet 6 mm thick
0224 Non-Asbestos fibre (high impact poly propelene reinforced) metre 218.52
cement close fitting adjustable ridge
0225 Non-Asbestos fibre (high impact poly propelene reinforced) metre 218.52
cement corrugate serrated adjustable ridge
0226 Non-Asbestos fibre (high impact poly propelene reinforced) metre 208.12
cement plain wing adjustable ridge
0227 Non-Asbestos fibre (high impact poly propelene reinforced) metre 312.17
cement unserrated adjustable ridge for hips
0228 Non-Asbestos fibre (high impact poly propelene reinforced) metre 234.12
cement corrugated apron piece
0229 Non-Asbestos fibre (high impact poly propelene reinforced) each 182.10
cement eaves filler piece
0230 Non-Asbestos fibre (high impact poly propelene reinforced) metre 322.57
cement north light curves
0231 Non-Asbestos fibre (high impact poly propelene reinforced) each 426.63
cement ventilator curves
0232 Non-Asbestos fibre (high impact poly propelene reinforced) metre 426.63
cement barge boards 6mm thick
0233 Non-Asbestos fibre (high impact poly propelene reinforced) pair 166.49
cement ridge finial
0234 Non-Asbestos fibre (high impact poly propelene reinforced) each 572.31
cement special north light curves
0235 Non-Asbestos fibre (high impact poly propelene reinforced) each 260.14
cement S type louvers

5 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
0236 Non-Asbestos fibre (high impact poly propelene reinforced) sqm 208.12
cement cement boards 6mm thick
0237 Non-Asbestos fibre (high impact poly propelene reinforced) sqm 260.14
cement cement boards8mm thick
0285 Brick Aggregate (Single size) 63 mm nominal size cum 1378.65
A For Uraban Patna cum 1470.00
B For Purnea,Saharsa,Bhagalpur,Munger & Darabhaga cum 1407.00
C For other places cum 1378.65
D For Patna Rural cum 1436.40
0286 Brick Aggregate (Single size) 50 mm nominal size cum 1378.65
A For Uraban Patna cum 1470.00
B For Purnea,Saharsa,Bhagalpur,Munger & Darabhaga cum 1407.00
C For other places cum 1378.65
D For Patna Rural cum 1436.40
0287 Brick Aggregate (Single size) 40 mm nominal size cum 1378.65
A For Uraban Patna cum 1470.00
B For Purnea,Saharsa,Bhagalpur,Munger & Darabhaga cum 1407.00
C For other places cum 1378.65
D For Patna Rural cum 1436.40
0291 Stone Aggregate (Singie size) 63 mm nominal size cum 458.12
0292 Stone Aggregate (Single size) 50 mm nominal size. cum 458.12
0293 Stone Aggregate (Single size) 40 turn nominal size cum 472.54
0294 Stone Aggregate (Single size) 25 mm nominal size cum 563.31
0295 Stone Aggregate (Single size) 20 mm nominal size cum 590.84
0296 Stone Aggregate (Single size) 12.5 mm nominal size cum 689.78
0297 Stone Aggregate (Single size) 10 mm nominal size cum 659.07
0298 Stone Aggregate (Single size) 6 mm nominal size cum 437.69
0302 Safeda bailies 125 mm diameter metre 43.71
0303 Cowdung cum 49.95
0304 Bajri cum 1040.57
0305 Bamboo 25mm dia 2.5 meter long score 364.20
0308 Bhusa quintal 416.22
0309 Paving bitumen S-90 of approved quality tonne 41622.58
0310 Bitumen emulsion tonne 27365.10
0312 Bitumen grade PMB- 40 tonne 43079.37
0313 Blown type petrolium bitumin of Plnitrah on 85/25 of oproved tonne 38500.88
quality
0314 Bitumen hot sealing compound Grade A kilogram 27.05
0316 Bitumen hot sealing compound Bitumen solution primer of litre 46.83
approved quality
0317 Premoulded joint filler 12 mm thick sqm 364.20
0318 Bitumen felt fibre base (vegetable or animal) :As per IS 7193 sqm 62.43
Grade I
0319 Bitumen felt as per IS 7193 Grade II sqm 79.08
0322 Bitumen felt Type 3 grade I confirming to IS : 1322 sqm 62.43
0323 Separation Membrane of impermeable plastic sheeting 125 sqm 12.48
micron thick
0324 Coal tar litre 31.21
0325 Blasting Material Blasting powder kilogram 36.42
0326 Blasting Material Blasting fuse (fuse wire) each 15.61
0328 White face insulating board: 12 mm thick sqm 374.61
0332 Natural colour insulating board: 12 mm thick sqm 280.95
0336 Flame retardant face insulating board: 12 mm thick sqm 327.78

BCD/SOR_8th Edition_October 2016 6

 Present
Code No Description Unit
Approved rate
1 2 3 4
0339 Flame retardant face insulating board: Impregnated fibre board sqm 364.20
12 mm thick
0341 Flat pressed 3 layer particle board (medium density) Grade I 12 sqm 338.18
mm thick
0346 Extra for veneered particle board with Teak veneering on one sqm 270.55
side and commercial veneering on other side
0347 Extra for veneered particle board with Commercial veneering pn sqm 176.89
both sides
0348 Extra for veneered particle board with Teak veneering on both sqm 520.28
sides
0349 Curing compound litre 52.02
0362 Brick bats cum 1135.05
A For Uraban Patna cum 1236.90
B For Purnea,Saharsa,Bhagalpur,Munger & Darabhaga cum 1168.65
C For other places cum 1135.05
D For Patna Rural cum 1185.45
0364 Wire brush each 20.81
0365 Soft brush each 18.73
0367 Portland Slag cement (P.S.C.) tonne 6131.27
0367A Patna tonne 6405.94
0367B Muzaffarpur tonne 6405.94
0367C Darbhanga tonne 6405.94
0367D Bhagalpur tonne 6405.94
0367E Munger tonne 6156.24
0367F Saharsa tonne 6405.94
0367G Purnea tonne 6405.94
0367H Gaya tonne 6131.27
367 I Saran tonne 6308.33
0367 Portland pozaiona cement (P.P.C.) tonne 4676.20
0367A Patna tonne 5336.77
0367B Muzaffarpur tonne 5336.77
0367C Darbhanga tonne 5425.30
0367D Bhagalpur tonne 5336.77
0367E Munger tonne 5284.56
0367F Saharsa tonne 5425.30
0367G Purnea tonne 5425.30
0367H Gaya tonne 4676.20
367 I Saran tonne 5216.46
0368 White cement tonne 14567.90
0369 Plastic sheath,1.25 mm thick for dowel bars sqm 31.21
0370 Coal (Steam) quintal 416.22
0371 Sealant primer kg 130.07
0373 Cramp Gun metal 25x6x300 mm each 83.25
0374 Pre moulded Joint filler, 25 mm thick for expansion joint. sqm 520.28
0378 Brass butt hinges (Light/Ordinary type) 125x70x4 mm ten 884.48
0379 Brass butt hinges (Light/Ordinary type) 100x70x4 mm ten 728.39
0380 Brass butt hinges (Light/Ordinary type) 75x40x2.5 mm ten 447.44
0381 Brass butt hinges (Light/Ordinary type) 50x40x2.5 mm ten 187.30
0382 Brass butt hinges (heavy type) 125x85x5.5 mm(0.70kg) ten 3225.75
0383 Brass butt hinges (heavy type; 100x85x5.5 mm(0.56kg) ten 2861.55
0384 Brass butt hinges (heavy type) 75x65x4.0 mm(0.20kg) ten 988.53
0385 Brass parliamentary hinges 150x125x27x5 mm ten 2965.61

7 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
0386 Brass parliamentary hinges 125x125x27x5 mm ten 2601.42
0387 Brass parliamentary hinges 100x125x27x5 mm ten 2393.30
0388 Brass parliamentary hinges 75x100x20x3.2 mm ten 1820.99
0389 Brass single acting spring hinges 150 mm each 322.57
0390 Brass single acting spring hinges 125 mm each 280.95
0391 Brass single acting spring hinges 100 mm each 176.89
0392 Brass double acting Spring Hinges 150mm each 520.28
0393 Brass double acting Spring Hinges 125mm each 385.01
0394 Brass double acting Spring Hinges 1 OOmm each 332.98
0400 Brass tower boits (barrel type) 250x10 mm each 239.33
0401 Brass tower bolts (barrel type) 200x10 mm each 187.30
0402 Brass tower bolts (barrel type) 150x10 mm each 150.89
0403 Brass tower bolts (barrel type) 100x10 mm each 98.85
0404 Brass flush bolts 250 mm each 156.08
0405 Brass flush bolts 150 mm each 135.27
0406 Brass flush bolts 100 mm each 93.65
0408 Brass handles 125mm with plate 175x32 mm each 145.68
0409 Brass handles 100mm with plate 150x32 mm each 135.27
0410 Brass handles 75mm with plate 125x32 mm each 104.06
0411 Brass door latch 300x16x5 mm (0.380 Kg) each 171.70
0412 Brass door latch 250x16x5 mm (0.350 Kg) each 166.49
0413 Brass mortice latch and lock 100x65 mm with 6 levers and a pair each 385.01
of brass lever handles
0414 Brass mortice latch 100x65 mm with a pair of brass level each 332.98
handles
0417 Brass 150mm floor door stopper (0.357 Kg) each 176.89
0418 Brass hard drwn hooks and eyes 300mm 10 nos 780.42
0419 Brass hard drawn hooks and eyes 250 mm ten 728.39
0420 Brass hard drawn hooks and eyes 200 mm ten 671.17
0421 Brass hard drawn hooks and eyes 150 mm ten 645.15
0422 Brass hard drawn hooks and eyes 100 mm ten 546.30
0423 Brass casement window fastener each 52.02
0424 Brass casement stays (straight peg type) 300 mm weighing not each 140.48
less than 0.33 kg
0425 Brass casement stays (straight peg type) 250 mm weighing not each 114.46
less than 0.28 kg
0426 Brass casement stays (straight peg type) 200 mm weighing not each 104.06
less than 0.24 kg
0427 Brass quadrant stays 300 mm each 130.07
0428 Brass fanlight catch each 182.10
0429 Brass fanlight pivot ten 202.91
0430 Brass chain with hook for fan light catch each 41.62
0431 Brass hasps and Staples (Safety type) 300 mm ten 806.44
0432 Brass hasps and Staples (Safety type) 115 mm ten 676.37
0433 Brass hasps and Staples (Safety type) 90 mm ten 582.71
0438 Brass Night latch each 515.08
0442 Brass helical Spring 150 mm each 322.57
0443 Brass curtain rod 12 mm dia 1.25 mm thick metre 87.39

BCD/SOR_8th Edition_October 2016 8

 Present
Code No Description Unit
Approved rate
1 2 3 4
0444 Brass curtain rod 20 mm dia 1.25 mm thick metre 119.66
0445 Brass curtain rod 25 mm dia 1.25 mm thick metre 140.48
0446 Brass brackets (curtain rods) 20 mm each 43.71
0447 Brass cupboard knob or ward robe knob 50 mm each 36.42
0449 Brass screws 50 mm cent 218.52
0450 Brass screws 40 mm cent 176.89
0451 Brass screws 30 mm cent 140.48
0452 Bras screws 25 mm cent 98.85
0453 Brass screws 20 mm cent 93.65
0524 Chromium plated Brass butt hinges (heavy) type 75x65x4.0 mm 10Nos. 1040.57
(200gms)
0525 Chromium plated Brass butt hinges (light / ordinary) type 10 Nos. 884.48
125x70x4.0 mm
0526 Chromium plated Brass butt hinges (light / ordinary) type 10Nos. 728.39
100x70x4.0 mm
0527 Chromium plated Brass butt hinges (light / ordinary) type 10 Nos. 478.66
75x40x2.5 mm
0528 Chromium plated Brass butt hinges (light / ordinary) type 10 Nos. 208.12
50x40x2.5 mm
0555 Chromium plated Brass handles 125mm with plate 175x32mm each 182.10
0556 Chromium plated Brass handles 100mm with plate 150x32mm each 156.08
0557 Chromium plated Brass handles 75mm with plate 125x32mm each 135.27
0558 Chromium plated Brass mortice latch and lock 100mm x 65mm each 561.90
with 6 levers and apair of brass lever and a pair or brass handles
0568 Chromium plated Brass casement window fastner each 98.85
0569 Chromium plated Brass casement stays (straight peg type) each 156.08
300mm weighing not less than 0.33 Kg.
0570 Chromium plated Brass casement stays (straight peg type) each 135.27
250mm weighing not less than 0.28 Kg.
0571 Chromium plated Brass casement stays (straight peg type) each 119.66
200mm weighing not less than 0.24 Kg
0583 Chromium plated Brass single acting spring hinges Night latch each 551.50
0584 Chromium plated Brass .Wardrobe Knob 50 mm each 49.95
0585 Chromium plated Brass screws 50mm 100 Nos 249.74
0586 Chromuim plated Brass screws 40mm 100 Nos 208.12
0587 Chromium plated Brass screws 30mm 100 Nos 161.29
0588 Chromium plated Brass screws 25mm 100 Nos 124.87
0589 Chromium plated Brass screws 20mm 100 Nos 104.06
0590 Chromium plated brass curtain rod 12 mm dia 1.25 mm thick meter 197.70
0591 Chromium plated brass curtain rod 20 nm dia 1.25 mm thick meter 270.55
0592 Chromiurr: plated brass curtain rod 25 mm dia 1.25 mm thick meter 364.20
0594 Brigh finish or black enameted mild steel butt hinges 10 Nos 145.68
125x65x2.12mm
0595 Brigh finish or black enameted mild steel butt hinges 10 Nos 88.45
100x58x1.90mm
0596 Brigh finish or black enameted mild steel butt hinges 75x47x1.70 10 Nos 62.43
mm
0597 Brigh finish or black enameted mild steel butt hinges 50x37x1.50 10 Nos 52.02
mm

9 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
0598 150x125x27x2.80 mm porliamentary hinges 10 Nos 384.98
0599 125x125x27x2.80 mm porliamentary hinges 10 Nos 346.49
0600 100x125x27x2.80 mm popliamentary hinges 10 Nos 230.99
0601 75x100x20x2.24 mm parliomentory hinges 10 Nos 183.60
0602 150 mm single acting spring hinges each 111.05
0603 125 mm single acting spring hinges each 96.25
0604 100 mm single acting spring hinges each 77.00
0605 150 mm double acting spring hinges each 134.75
0606 125 mm double acting spring hinges each 109.57
0607 100 mm double acting spring hinges each 69.58
0608 Nickel plated miid steel piano hinges 1 mm thick 35 mm wide metre 41.62

0614 300x20x6 mm door latch each 38.50

0615 250x20x6 mm door latch each 31.10
0620 125 mm handles each 7.41
0621 100 mm handles each 5.92
0622 75 mm handles each 4.44
0632 115 mm hasper & stopler ( safety type ) 10 Nos 87.37
0633 90 mm hasper & stopler ( safety type ) 10 Nos 68.11
0635 Brigh finish or black enameled mild steel screws 50 mm 100 Nos 67.64
0636 Oxidiged mild steel 45 mm screw 100 Nos 48.85
0637 Bright finish or black enameled mild steel screws 40 mm 100 Nos 52.02
0638 Bright finish or black enameled mild steel screws 30 mm 100 Nos 41.62
0639 Bright finish or black enameled mild steel screws 25 mm 100 Nos 36.42
0640 Bright finish or black enameled mild steel screws 20 mm 100 Nos 31.21
0641 Mild steel fittings bright finished or black enameled bolts and each 7.28
nuts 50 X 6mm
0642 Oxidised mild steel butt hinges 125x65x2.12mm 10 Nos 145.68
0643 Oxidised mild steel butt hinges 100x58x1.90mm 10 Nos 93.65
0644 Oxidised mild steel butt hinges 75x47x1.70mm 10 Nos 67.64
0645 Oxidised steel mild butt hinges 50x37x1.50rnrn 10 Nos 57.23
0646 Oxidised steel mild parliamentary hinges 150x125x27x2.80 mm 10 Nos 353.80
0647 Oxidised steel mild parliamentary hinges 125x125x27x2.80 mm 10 Nos 327.78
0648 Oxidised steel mile' parliamentary hinges 100x125x27x2.80 mm 10 Nos 244.53
0649 Oxidised steel mild parliamentary hinpes 75x100x20x2.24 mm 10 Nos 208.12
0650 Oxidised mild steel Single acting spring hinges 150mm each 119.66
0651 Oxidised mild steel Single acting spring hinges 125 mm each 114.46
0652 Oxidised mild steel Single acting spring hinges 100 mm each 93.65
0653 Oxidised mild steel double acting spring hinges 150 mm each 119.66
0654 Oxidised mild steel double acting spring hinges 125 mm each 114.46
0655 Oxidised mild steel double acting spring hinges 100 mm each 93.65
0656 Nickel plated mild steel piano, hinges 1 mm thick 35mm wide metre 46.83
0660 Oxidised mild steel sliding door bolts 300x16mm each 98.85
0661 Oxidised mild steel sliding door bolts 250x16mm each 93.65
0662 Oxidised mild steel door latch 300x20x6 mm each 49.95

BCD/SOR_8th Edition_October 2016 10

 Present
Code No Description Unit
Approved rate
1 2 3 4
0663 Oxidised mild steel door latch 250x20x6 mm each 41.62
0664 Oxidised mild steel tower bolts (barrel type) 250x10 mm each 46.83
0665 Oxidised mild steel lower bolts (barrel type) 200x10 mm each 41.62
0666 Oxidised mild steel tower bolts (barrel type) 150x10 mm each 31.21
0667 Oxidised mild steel tower bolts (barrel type) 100x10 mm each 26.02
0668 Oxidised mild steel handles 125 mm each 19.77
0669 Oxidised mild steel handles 100 mm each 16.65
0670 Oxidised mild steel handles 75 mm each 15.61
0679 Oxidised mild steel hasps and staples (safety type) 150 mm 10 Nos 130.07
0680 Oxidised mild steel hasps and staples (safety type) 115 mm 10 Nos 104.06
0681 Oxidised mild steel hasps and staples (safety type) 90 mm 10 Nos 78.04
0682 Oxidised mild steel screws 50 mm 100 Nos 78.04
0683 Oxidised mild steel screws 40 mm 100 Nos 62.43
0684 Oxidised mild steel screws 30 mm 100 Nos 57.23
0685 Oxidised mild steel screws 25 mm 100 Nos 46.83
0686 Oxidised mild steel screws 20 mm 100 Nos 36.42
0687 Anodised Aluminium butt hinges 125x75x4 mm 10 Nos 593.12
0688 Anodised Aluminium butt hinges 125x63x4 mm 10 Nos 551.50
0689 Anodised Aluminium butt hinges 100x75x4 mm 10 Nos 541.09
0690 Anodised Aluminium butt hinges 100x63x3.2 mm 10 Nos 520.28
0691 Anodised Aluminium butt hinges 100x63x4 mm 10 Nos 530.69
0692 Anodised Aluminium butt hinges 75x63x4 mm 10 Nos 520.28
0693 Anodised Aluminium butt hinges 75x63x3.2 mm 10 Nos 489.07
0694 Anodised Aluminium butt hinges 75x45x3.2 mm 10 Nos 405.82
0695 Anodised Aluminium butt hinges 50x35x3.2 mm 10 Nos 106.62
0696 Anodised Aluminium silding door bolt 300x16 mm each 166.49
0697 Anodised Aluminium silding door bolt 250x16 mm each 135.27
0698 Anodised Aluminium tower bolt (barrel type)300xi0 mm 10 Nos 780.42
0699 Anodised Aluminium tower bolt (barrel type)250x10 mm 10 Nos 624.34
0700 Anodised Aluminium tower bolt (barrel type)200x10 mm 10 Nos 499.47
0701 Anodised Aluminium tower bolt (barrel type) 150x10 mm 10 Nos 395.41
0702 Anodised Aluminium tower bolt (barrel type) 100x10 mm ten 312.17
0703 Anodised Aluminium handles 125 mm with plate 175x32 mm ten 520.28
0704 Anodised Aluminium nandies 100 mm with plate 150x32 mm ten 395.41
0705 Anodised Aluminium handles 75 mm with plate 125x32 mm ten 332.98
0706 Anodised Aluminium kicking plate 50cm long 100x3.15 mm each 135.27
0713 Block Board Construction flush door with teak wood ply on both sqm 1768.96
faces 35 mm thick
0714 Block Board Construction flush door with teak wood ply on both sqm 1612.87
faces 30 mm thick
0715 Block Board Construction flush door with teak wood ply on both sqm 1456.79
faces 25 mm thick
0717 Block board construction flush door with Commercial ply on both sqm 1196.65
faces 35 mm thick
0718 Block board construction flush door with Commercial ply on both sqm 1040.57
faces 30 mm thick

11 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
0719 Block board construction flush door with Commercial ply on both sqm 936.51
faces 25 mm thick
0752 Block board construction flush door lipping sqm of door 312.17
area
0753 Square vision Panel in Block board construction flush door sqm of door 119.66
area
0754 Circular Vision Panel in block board construction flush door sqm of door 187.30
area
0755 Decorative type Louvers in Block board construction flush door sqm of door 322.57
area
0757 Rebate cutting in Block board construction flush door sqm of door 88.45
area
0759 Decorative Plywood 4 mm sqm 437.03
0761 Fuel Wood quintal 520.28
0763 Glue kilogram 70.76
0765 Hessian cloth sqm 26.02
0768 Jali (cement concrete) 50mm thick sqm 218.52
0769 Jali (cement concrete) 40mm thick sqm 187.30
0770 Jali (cement concrete) 25mm thick sqm 156.08
0771 Kerosene oil litre 46.83
0773 Lime Unslaked lime quintal 312.17
0775 Lime Dehradun white lime quintal 499.47
0776 Lime Satna lime quintal 312.17
0777 Lime Dry hydrated lime (factory made) quintal 239.33
0784 Marble dust / powder cum 1040.57
0785 Marble chips upto 4mm and down size White & black quintal 208.12
0786 Marble chips upto 4mm and down size Chocolate, grey or yellow quintal 170.29
0787 Marble chips upto 4mm and down size Baroda green quintal 170.29
0788 Marble chips Large size above 4mm. white & black quintal 208.12
0801 Silicon and acrylic emulsion litre 208.12
0802 Acrylic distemper 1st quality , having VOC content less than Kg 39.54
50gm/litre
0803 Acrylic emulsion , having VOC content less than 50 gm/litre litre 260.14
0804 Premium acrylic emulsion of interior grade, having VOC content litre 364.20
less than 50 gm/litre
0805 Synthetic enamel paint , having VOC (Volatile Organic litre 228.93
Compound) content less than 150 gm/litre
0806 Ready mixed pink or grey primer on wood work (hard and soft litre 124.87
wood) having VOC content less than 50 gms/litre
0807 Ready mixed red oxide zinc chromatic on steel/ iron work, having litre 135.27
VOC content less than 250 gms/litre
0808 Water thinnable cement primer for interior wall surface, having litre 62.43
VOC content less than 50 gms/litre
0809 Exterior Primer kg 41.62
0810 Moorum cum 139.95
0811 Mud (dry) cum 62.43
0815 Dry Distemper kilogram 37.46
0816 Oil bound washable distemper / Acrylic distemper kilogram 46.83
0818 Oil / Fuel Linseed oil (double boiled) litre 114.46

BCD/SOR_8th Edition_October 2016 12

 Present
Code No Description Unit
Approved rate
1 2 3 4
0820 Primers Cement primer litre 93.65
0821 Primers Distemper primer litre 93.65
0823 Primers Pink primer (for wood) litre 93.65
0824 White cement based putty kg 24.97
0826 Aluminium paint litre 135.27
0827 Acid proof paint (chocolate or black) litre 156.08
0828 Anti-corrosive bituminous paint (black) litre 93.65
0829 Black Japan litre 98.85
0830 Enamel paint litre 166.49
0831 Floor enamel paint in all shades except green litre 124.87
0833 Synthetic enamel paint black or chocolate shade litre 135.27
0834 Synthetic enamel paint in ail shades except black or chocolate litre 145.68
0835 Plastic emulsion paint litre 187.30
0845 Roofing paint for iron sheets in red colour litre 124.87
0850 White lead kilogram 93.65
0851 Water proofing cement paint Snowcem Plus kilogram 46.83
0855 Polish Wax polish (ready made) kilogram 208.12
0856 Varnishes Ordinary varnish litre 78.04
0857 Varnishes Superior copal varnish litre 130.07
0858 Varnishes Superior spar varnish litre 130.07
0859 Oil type wood preservative litre 83.25
0863 Polish Putty for wood work kilogram 31.21
0865 Pigments Pig lead kilogram 130.07
0868 Premixed super white gypsum plaster. kg 7.28
0869 Plaster of Paris kilogram 4.16
0870 Pigments Plug each 10.40
0873 Pigments Pins - Copper pins 6 mm dia 7.5cm long each 10.40
0874 Pigments black colour dark shade kilogram 57.23
0875 Pigments Red chocolate orange buff or yellow (red oxide of iron kilogram 78.04
) light shade
0876 Pigments green or blue medium shade kilogram 67.64
0886 standard holdar bat clamps for sand cast iron or cast iron pipes each 26.02
150mm dia
0966 sand cast iron plain shoe 150mm dia each 338.18
0967 pigments plate -copper kilogram 280.95
0969 Pulleys 25mm dia each 36.42
0973 Rolling shutters and its parts Rolling shutter made of sqm 1300.71
80X1.25mm machine rolled laths
0974 Rolling shutters and its parts Top cover for rolling shutters metre 624.34
0975 Rolling shutters and its parts 27.5cm long wire spring grade No 2 each 291.36
for rolling Shutters
0976 Rolling shutters and its parts ball bearing for rolling shutters each 343.39
0977 Extra for mechnical devices chain and cranked operation for sqm 572.31
operating rolling shutters Exceeding 10.00 sqm and upto 16.80
sqm area of door
0978 Extra for mechnical devices chain and cranked operation for sqm 603.53
operating rolling shutters Exceeding 16.80 sqm area of door

13 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
0979 Royalty for good earth cum 31.21
0980 Royalty for sludge cum 93.65
0982 Sand Coarse sand Doriganj equvalent to Koilwar/Sone sand cum 286.70
982A Sand Coarse sand querry at Koilwar/Sone 146.67
0983 Fine sand (zone IV) cum 124.54
0992 Galvanised steel plain sheets quintal 5410.94
0994 Standard quality hard board sheet 3mm thick sqm 130.07
0996 Sheets standard quality had board sheet 4.5mm thick sqm 156.08
0999 Polish shellac kilogram 218.52
1000 Oil/Fuel spirit litre 72.84
1003 Mild steel round bar above 12mm dia quintal 3606.75
1001 Spun yarn kilogram 41.62
1002 Mild steel round bar 12mm dia and below quintal 3606.75
1004 Mild steel wire rod quintal 3591.00
1004A 5.5mm quintal 3606.75
1004B 6.0mm quintal 3591.00
1004C 6.5mm quintal 3575.25
1004D 7.0mm quintal 3559.50
1004E 8.00mm quintal 3543.75
1004F 10.0mm quintal 3606.75
1004G 12.0/12.7mm quintal 3606.75
1005 Steel T.M.T. Bars Fe 500 quintal 3496.50
1005A TMTC-500-8mm quintal 3685.50
1005B TMTC-500-10mm quintal 3580.50
1005C TMTC-500-12mm quintal 3528.00
1005D TMT FE-500-16mm quintal 3554.25
1005E TMT FE-500-20mm quintal 3496.50
1005F TMT FE-500-25mm quintal 3496.50
1005G TMT FE-500-28mm quintal 3496.50
1005H TMT FE-500-32mm quintal 3496.50
1005 I TMT FE-500-36mm quintal 3496.50
1006 Mild steel square bars quintal 3936.99
1007 A STEEL JOIST quintal 4195.21
a 200X100 quintal 4195.21
b 225X110 quintal 4195.21
c 250X125 quintal 4259.46
d 300X140 quintal 4259.46
e 350X140 quintal 4390.39
f 400X140 quintal 4518.75
g 450X150 quintal 4637.00
h 500X180 quintal 4755.25
i 600X210 quintal 5110.22
1007B STEEL CHANNEL quintal 3344.25
a 75X40 quintal 3344.25
b 100X50 quintal 3344.25

BCD/SOR_8th Edition_October 2016 14

 Present
Code No Description Unit
Approved rate
1 2 3 4
c 125X65 quintal 3344.25
d 150X75 quintal 3344.25
e 175X75 quintal 3344.25
f 200X75 quintal 3344.25
g 250X82 quintal 3344.25
h 300X90 quintal 3344.25
i 400X100 quintal 3344.25
1007C STEEL ANGLES quintal 4126.50
a 50x50x6 quintal 4126.50
b 60X60X6 quintal 4126.50
c 65X65X6 quintal 4126.50
d 75X75X6 quintal 4126.50
e 80X80X8/10/12 quintal 4126.50
f 90X90X6 quintal 4126.50
g 100X100X8/10/12 quintal 4126.50
h 110X110X8/10/12 quintal 4126.50
i 130X130X10/12 quintal 4126.50
j 150X150X12/16/20 quintal 4126.50
k 200X200X16/18/26 quintal 4126.50
1008 Flats upto 10mm in thickness quintal 4370.37
1009 Flats exceeding 10mm in thickness quintal 4682.54
1010 Mild steel plates quintal 4890.66
1011 Steel glazed door,window/ ventilator, all members viz. F7D, kg 49.95
F4B,K11 and K12B etc.
1013 Mild steel sheets for tanks quintal 5098.76
1015 Mild steel expanded metal 20x60 mm strands sqm 301.76
1019 Mild steel hooks each 36.42
1020 Mild steel rivets quintal 5202.82
1021 Hard drawn steel wire fabric sqm 447.44
1022 Galvanised steel bolts and nuts 6mm dia. And 25mm long round ten 26.02
head with slots
1023 Galvanised steel J or L hooks 8mm dia. Ten 114.46
1024 Galvanised steel bolts and nuts 10mm dia. and 125mm long each 12.48
1025 Mild steel bolts 6mm dia and 25mm long with hexagonal head ten 31.21
1028 Straining bolts each 72.84
1029 Galvanised steeL barbed wire quintal 5410.94
1030 Galvanised steel turn buckles each 17.69
1031 Galvanised steel bolts & nut 10mm dia 27cm long both sides each 26.02
threaded with 4 galvanised steel nuts
1032 Galvanised steel bolts 10mm dia 7cm long with nuts each 20.81
1034 Bolts and nuts upto 300mm in length quintal 5827.16
1035 Bolts and nuts above 300mm in length quintal 5827.16
1036 Iron Pintels including welded pin each 41.62
1143 Steel Beading metre 26.02
1145 Aluminium Plain Strip edging 38x12x3 mm metre 104.06
1149 Glass strips 4mm thick 40mm deep metre 9.36
1151 Boundry stone top chisel dressed 15x15x90cm each 62.43

15 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
1154 Through and bond stone 100 nos 1248.67
1157 Stone for masonry work cum 728.39
1158 Stone for pitching 15cm x 22.5cm cum 468.26
1159 Stone dust cum 104.67

1160 Red sand stone block 10 cudm 67.64

1161 White sand stone block 10 cudm 72.84
1163 White sand stone slab 75mm thick (un-dressed) sqm 312.17
1164 Red sand stone slab 40mm thick (undressed) sqm 166.49
1165 'White sand stone slab 40mm thick (undressed) sqm 187.30
1166 Red sand stone slab 30mm thick (undressed) sqm 135.27
1168 Kota stone slab 20mm to 25mm thick (semi-polished) sqm 301.76
1169 Kota stone slab 25mm thick (rough chiselled) sqm 218.52
1174 Red sand stone slab 45/50mm thick (un-polished) sqm 178.98
1175 White sand stone slab 45/50mm thick (undressed) sqm 234.12
1177 Stone grit 6 mm and down size or pia sized grand cum 962.52
1179 Crushed stone 2.36 mm to 12.5 mm size cum 988.53
1182 Surkhi cum 1941.45
A Uraban Patna cum 1941.45
B For Purnia,Bhagalpur,Saharasa,Munger,Darabhanga cum 1861.65
C For other places cum 1797.60
D For Patna Rural cum 1874.25
1186 Superior class teak wood such as Dandeli, Balarshah or Malabar 10 cudm 1144.62
in planks
1187 First class teak wood in scantling 10 cudm 832.45
1188 First class teak wood in planks 10 cudm 884.48
1189 Second class teak wood in scantling 10 cudm 686.77
1190 Second class teak wood in planks 10 cudm 754.41
1194 Second class deodar wood in pianks 10 cudm 520.28
1196 First class kail wood in planks 10 cudm 322.57
1197 Second class kail wood in scantling 10 cudm 270.55
1198 Second clas's kail wood in planks 10 cudm 270.55
1199 Sal wood in scantling 10 cudm 541.09
1195 Local wood in scantling 10 cudm 332.53
1200 Kiln seasoned selected sheesham wood planks 10 cudm 676.37
1201 Precast terrazo tiles 22 mm thick (light shade) sqm 270.55
1202 Precast terrazo tiles 22 mm thick (medium shade) sqm 249.74
1203 Precast terrazo tiles 22 mm thick (dark shade) sqm 228.93
1204 Precast heat resistant terrace tiles (size 300x300 mm) and 20 sqm 501.55
mm thick
1207 Washers Cadmium coated G.I. limpet washer cent 36.42
1208 Washers Bitumen washer cent 31.21
1209 Washers G.I. plain washer thick cent 36.42
1210 Washers G.I. plain washer thin cent 33.30
1211 Washers G.I. plain washer for seam bolts cent 31.21
1213 Water proofing compound 'Impermo' of Snowcem India Ltd. kilogram 33.30
1214 Welding By gas plant cm 2.08

BCD/SOR_8th Edition_October 2016 16

 Present
Code No Description Unit
Approved rate
1 2 3 4
1215 Welding By electric plant cm 1.87
1216 Whiting quintal 520.28
1219 Wire nails kilogram 62.43
1220 Wire mesh (Rabbit) sqm 46.83
1221 20 mm dia holding down bolts quintal 6035.27
1222 Mild steel sheets with bolts and nuts to rest on lintels each 135.27
1224 Hard drawn steel wire quintal 5723.10
1225 Mild steel flat strap fitting quintal 4630.51
1227 Chequered terrazo tiles 22mm thick (light shade) sqm 338.18
1228 Chequered terrazo tiles 22mm thick (medium shade) sqm 296.56
1229 Chequered terrazo tiles 22mm thick (dark shade) sqm 260.14
1231 Extra for selected planks of second class teak wood 10 cudm 145.68
1234 Aluminium plain strip edging 57x12x3 mm metre 140.48
1235 Oil / Fuel Diesel oil litre 50.60
1237 Cutting marble or sand stone slab upto 50mm thick by metre 9.36
mechanical device
1238 Extra for selected planks of first class teak wood 10 cudm 145.68
1239 18 mm thick Flamed finish granite stone slab sqm 1763.76
1240 18 mm thick Italian Marble stone slab,(slab area up to 0.5 sqm). sqm 3465.08

1241 Oil / Fuel LPG (Commercial Cylinder) kg 72.84

1242 Glass mossaic tiles (20 mm x 20 mm x 4 mm ). sqm 1092.59
1243 Tile fixing chemical adhesive kg 35.38
1244 Cement Polymer Grout Compound kg 35.38
1245 Acid for cleaning tiles litre 16.65
1301 Bleaching powder quintal 1820.99
1304 Surface box for stop cock each 130.07
1305 Surface box for sluice valve each 218.52
1307 Surface box for water meter each 260.14
1309 C.I. bracket for wash basin and sinks pair 72.84
1314 C.P. brass chain with 32 mm dia rubber plug each 41.62
1315 C.P. brass chain with 40 mm dia rubber plug each 41.62
1330 Clamps and M.S. stays including bolts and nuts for 100 mm pipe each 36.42
1331 M.S. Holder bat clamp of approved design for 10 mm S.C.I.pipe each 20.81

1332 M.S. Holder bat clamp of approved design for 75mm S.C.I.pipe each 18.73

1334 Clamps and M.S. stays including bolts and nuts for 50 mm pipe each 29.14
1335 Clamps and M.S. stays including bolts and nuts for75 mm pipe each 31.21
1336 Clearing eye with chain and lid 100 mm dia each 45.78
1337 Clearing eye with chain and lid150 mm dia each 52.02
1339 Brass bib-cock 15 mm dia each 218.52
1340 Brass bib-cock 20mm dia each 234.12
1342 Brass stop-cock 15 mm dia each 218.52
1343 Brass stop-cock 20 mm dia each 291.36
1350 Mosquito proof coupling of approved design each 31.21

17 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
1352 C.l. cover and frame 300x300 mm inside each 312.17
1353 C.l. cover without frame 300x300 mm inside i/c cover of 4.50kg each 234.12
1354 Rectangular cover 455x610 mm with frame (low duty) each 1560.85
1355 Rectangular cover 455x610 mm without frame (low duty) each 1040.57
1356 500mm dia cover with frame (medium duty) each 4942.68
1357 500mm dia cover withought frame (medium duty) each 2393.30
1360 C.l.mouth ,brass ferrule 15 mm dia each 145.68
1361 C.l.mouth ,brass ferrule 20 mm dia each 166.49
1362 C.l.mouth ,brass ferrule 20 mm dia each 228.93
1363 Vitreous china foot rests 250x130x30 mm pair 104.06
1364 C.I. grating 100x100 mm each 15.61
1366 C.I. grating 150x150 mm each 26.02
1367 C.I. grating 180x180 mm each 31.21
1369 S.C.I. gully or nahani grating 100 mm dia each 18.73
1373 Rubber insertions for 80 mm dia pipe joints each 15.61
1374 Rubber insertions for 100 mm dia pipe joints each 18.73
1375 Rubber insertions for 125 mm dia pipe joints each 20.81
1376 Rubber insertions for 150 mm dia pipe joints each 20.81
1377 Rubber insertions for 200 mm dia pipe joints each 26.02
1378 Rubber insertions for 250 mm dia pipe joints each 41.62
1379 Rubber insertions for 300 mm dia pipe joints each 46.83
1380 Rubber insertions for 350 mm dia pipe joints each 52.02
1381 Rubber insertions for 400 mm dia pipe joints each 75.96
1382 Rubber insertions for 450 mm dia pipe joints each 95.73
1383 Rubber insertions for 500 mm dia pipe joints each 114.46
1384 Rubber insertions for 600 mm dia pipe joints each 130.07
1392 Mirror of superior make glass 60x45 cm each 322.57
1396 Vitreous china pedestal for wash basin each 728.39
1397 Pig lead kilogram 93.65
1464 S & S.C.I.standard specials up to 300 mm dia (heavy class) quintal 3746.03
1466 S & S.C.I.standard specials over 300 mm dia (heavy class) quintal 3850.09
1468 Flanged C.I. standard specials up to 300 mm dia(heavy class) quintal 5723.10
1470 Flanged C.I. standard specials over 300 mm dia(heavy class) quintal 6035.27
1472 Casing pipe 100 mm dia metre 348.59
1532 Flush pipe with union spreaders and clamps all in C.P. brass for each 280.95
single stall
1533 Flush pipe with union spreaders and clamps all in C.P. brass for each 416.22
double stall
1534 Flush pipe with union spreaders and clamps all in C.P. brass for each 541.09
range of three stall
1535 Flush pipe with union spreaders and clamps all in C.P. brass for each 624.34
range of four stall
1540 Flush pipe and spreaders G.I.for single set of one squatting plate each 182.10
urinal
1541 Flush pipe and spreaders G.I.for range of two squatting plates each 260.14
urinal

BCD/SOR_8th Edition_October 2016 18

 Present
Code No Description Unit
Approved rate
1 2 3 4
1542 Flush pipe and spreaders G.I.for range of three squatting plates each 312.17
urinal each
1543 Flush pipe and spreaders G.I.for range of four squatting plates each 405.82
urinal
1545 G.I. pipes 15 mm dia metre 88.45
1546 G.I. pipes 20 mm dia metre 114.46
1547 G.I. pipes 25 mm dia metre 156.08
1548 G.I. pipes 32 mm dia metre 187.30
1549 G.I. pipes 40 mm dia metre 228.93
1550 G.I. pipes 50 mm dia metre 286.16
1551 G.I. pipes 65 mm dia metre 379.80
1552 G.I. pipes 80 mm dia metre 478.66
1555 G.I. back (jam) nuts 25 mm dia each 10.40
1559 G.I. back (jam) nuts 65 mm dia each 22.90
1608 G.I. tees (equal) 25 mm each 46.83
1612 G.I. tees (equal) 65 mm each 291.36
1614 G.I. inlet connection each 67.64
1616 S.C.I. soil, waste and vent single socketed pipe1.80 metres long: each 988.53
75mm dia
1617 S.C.I. soil, waste and vent single socketed pipe1.80 metres each 1196.65
long:100mm dia
1618 S.C.I. soil, waste and vent single socketed pipe1.80 metres long: each 1820.99
150mm dia
1620 S.C.I. plain bend 75 mm dia each 176.89
1621 S.C.I. plain bend 100 mm dia each 364.20
1622 S.C.I. plain bend 150 mm dia each 624.34
1624 S.C.I. bend with access door 75 mm dia each 208.12
1625 S.C.I. bend with access door 100 mm dia each 262.22
1627 S.C.I. plain single equal junctions 75x75x75 mm dia each 275.75
1628 S.C.I. plain single equal junctions 100x100x100 mm dia each 468.26
1630 S.C.I. single equal junctions75x75x75 mm dia with access door each 289.28

1631 S.C.I. single equal junctions 100x100x100 mm dia with access each 391.25
door
1633 S.C.I. plain double equal junctions 75x75x75x75 mm dia each 360.04
1634 S.C.I. plain double equal junctions100x100x100x100 mm dia each 541.09
1636 S.C.I. double equal junctions75x75x75x75 mm dia with access each 442.24
door
1637 S.C.I. double equal junctions 100x100x100x100 mm dia with each 572.31
access door
1639 Slotted cowl (terminal guard) 75 mm dia each 157.13
1640 Slotted cowl (terminal guard) 100 mm dia each 197.70
1641 G.I. Union 15 mm nominal bore each 57.23
1642 G.I. Union 20 mm nominal bore each 78.04
1643 G.I. Union 25 mm nominal bore each 88.45

19 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
1644 G.I. Union 32 mm nominal bore each 124.87
1645 G.I. Union 40 mm nominal bore each 192.50
1646 G.I. Union 50 mm nominal bore each 228.93
1647 G.I. Union 65 mm nominal bore each 447.44
1648 G.I. Union 80 mm nominal bore each 530.69
1649 Polyethylene water storage tank with cover and suitable locking pair litre 4.68
arrangement
1653 Sand cast iron S&S plain single unequal junctions : 100x100x75 each 385.01
mm dia
1656 Sand cast iron S&S single unequal junctions: 100x100x75 mm each 416.22
dia with access door
1659 Sand cast iron S&S plain double unequal junctions : each 572.31
100x100x75x75 mm dia
1662 Sand cast iron S&S double unequal junctions: 100x100x75x75 each 572.31
mm dia with access door
1666 Sand cast iron heel rest bend 75 mm dia each 228.93
1667 Sand cast iron heel rest bend 100 mm dia each 260.14
1669 S.C.I. single equal invert branch of required degree75x75x75 each 332.98
mm dia
1670 S.C.I. single equal invert branch of required degree each 426.63
100x100x100 mm dia
1672 S.C.I. double equal invert branch of required degree each 426.63
75x75x75x75 mm dia
1673 S.C.I. double equal invert branch of required degree each 572.31
100x100x100x100 mm dia
1674 S.C.I. single unequal invert branch of required each 515.08
degree100x100x75 mm dia
1677 S.C.I. double unequal invert branchof required degree each 593.12
100x100x75x75 mm dia
1682 S.C.I. door pieces 75 mm dia each 286.16
1683 S.C.I. door pieces 100 mm dia each 416.22
1685 S.C.I. collar 75 mm dia each 117.58
1686 S.C.I. collar 100 mm dia each 148.80
1687 Unplasticised P.V.C. connection pipe with brass union 30 cm each 31.21
long 15 mm bore
1688 Unplasticised P.V.C. connection pipe with brass union 30 cm each 36.42
long 20 mm bore
1689 Unplasticised P.V.C. connection pipe with brass union 45 cm each 36.42
long 15 mm bore
1690 Unplasticised P.V.C. connection pipe with brass union 45 cm each 49.95
long 20 mm bore
1693 S.C.I. hand pump each 697.18
1700 R.C.C. pipes NP2 class 100 mm dia metre 208.12
1701 R.C.C. pipes NP2 class 150 mm dia metre 218.52
1702 R.C.C. pipes NP2 class 250 mm dia metre 270.55
1703 R.C.C. pipes NP2 class 300 mm dia metre 312.17
1704 R.C.C. pipes NP2 class 450 mm dia metre 416.22

BCD/SOR_8th Edition_October 2016 20

 Present
Code No Description Unit
Approved rate
1 2 3 4
1705 R.C.C. pipes NP2 class 500 mm dia metre 603.53
1706 R.C.C. pipes NP2 class 600 mm dia metre 957.32
1707 R.C.C. pipes NP2 class 700 mm dia metre 1092.59
1709 R.C.C. pipes NP2 class 800 mm dia metre 1217.46
1710 R.C.C. pipes NP2 class 900 mm dia metre 1331.92
1711 R.C.C. pipes NP2 class 1000 mm dia metre 1654.49
1712 R.C.C. pipes NP2 class 1100 mm dia metre 1951.06
1713 R.C.C. pipes NP2 class 1200 mm dia metre 2003.09
1714 R.C.C. pipes NP2 class 100 mm dia each 31.21
1715 R.C.C. pipes NP2 class 150 mm dia each 36.42
1716 R.C.C.collars NP2 class 250 mm dia each 52.02
1717 R.C.C.collars NP2 class 300 mm dia each 57.23
1718 R.C.C.collars NP2 class 450 mm dia each 104.06
1719 R.C.C. collars NP2 class 500 mm dia each 119.66
1720 R.C.C.collars NP2 class 600 mm dia each 145.68
1721 R.C.C. collars NP2 class 700 mm dia each 156.08
1723 R.C.C.collars NP2 class 800 mm dia each 208.12
1724 R.C.C. collars NP2 class 900 mm dia each 244.53
1725 R.C.C. collars NP2 class 1000 mm dia each 291.36
1726 R.C.C. collars NP2 class 1100 mm dia each 312.17
1727 R.C.C. collars NP2 class 1200 mm dia each 364.20
1728 RCC pipe 450 mm dia NP-3 spigot metre 1556.69
1729 RCC pipe 600 mm dia NP-3 spigot metre 2075.92
1730 RCC pipe 900 mm dia NP-3 spigot metre 3277.78
1731 RCC pipe 1000 mm dia NP-3 spigot metre 4042.59
1732 RCC pipe 1200 mm dia NP-3 spigot metre 5244.44
1733 RCC pipe 1800 mm dia NP-3 spigot metre 9833.33
1734 RCC pipe 450 mm dia NP-4 spigot metre 1803.30
1735 RCC pipe 600 mm dia NP-4 spigot metre 2403.70
1736 RCC pipe 900 mm dia NP-4 spigot metre 4781.39
1737 RCC pipe 1000 mm dia NP-4 spigot metre 5790.74
1738 RCC pipe 1200 mm dia NP-4 spigot metre 6774.08
1739 RCC pipe 1800 mm dia NP-4 spigot metre 14203.71
1854 Stoneware pipes grade A (60 cm long) 100 mm dia each 52.02
1855 Stoneware pipes grade A (60 cm long) 150 mm dia each 83.25
1856 Stoneware pipes grade A (60 cm long) 200 mm dia each 138.39
1857 Stoneware pipes grade A (60 cm long) 230 mm dia each 176.89
1858 Stoneware pipes grade A (60 cm long) 250 mm dia each 228.93
1859 Stoneware pipes grade A (60 cm long) 300 mm dia each 249.74

21 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
1863 Fire clay kitchen sink: 600x450x250 mm each 1404.77
1871 White vitreous china laboratory sink450x300x150 mm each 853.26
1872 White vitreous china laboratory sink600x450x200 mm each 1586.86
1875 White plastic seat (solid)with lid C.P.brass hinges and rubber each 343.39
buffers
1876 Black plastic seat (solid) with lid C.P.brass hinges and rubber each 322.57
buffers
1878 Shower rose C.P.brass for 15 to 20 mm inlet 100 mm dia each 52.02
1879 Shower rose C.P.brass for 15 to 20 mm inlet 150 mm dia each 62.43
1881 Spun yarn kilogram 52.02
1882 Strainer brass 40 mm dia 1.5 metre long each 624.34
1885 15 mm C.P.brass tap each 218.52
1889 C.P.brass toilet paper holder of standard size each 176.89
1891 C.I. trap for standard urinal with vent arm with operating and each 176.89
other couplings in C.P.brass: 50 mm dia
1893 C.I. trap for standard urinal with vent arm with operating and each 234.12
other couplings in C.P.brass: 80 mm dia
1895 C.P.brass trap40 mm dia each 156.08
1896 100 mm S.C.I. trap with vent heel each 327.78
1897 100 mm S.C.I. trap with 100 mm inlet and 100 mm outlet each 286.16
1898 100 mm S.C.I. trap with 100 mm inlet and 75 mm outlet each 226.84
1900 S.W. gully trap P type 100x100 mm each 93.65
1902 S.W. gully trap P type 150x100 mm each 135.27
1904 S.W. gully trap P type 180x150 mm each 234.12
1913 Vitreous china lipped front urinal each 478.66
1915 Vitreous china squatting plate urinal each 790.83
1922 H.P. or L.P. ball valve with polythene floats: 15 mm dia each 218.52
1923 H.P. or L.P. ball valve with polythene floats: 20 mm dia each 317.37
1924 H.P. or L.P. ball valve with polythene floats: 25 mm dia each 343.39
1927 Brass full way valve with C.I. wheel (screwed end) 25 mm dia each 364.20
1928 Brass full way valve with C.I. wheel (screwed end) 32 mm dia each 426.63
1929 Brass full way valve with C.I. wheel (screwed end) 40 mm dia each 499.47
1930 Brass full way valve with C.I. wheel (screwed end) 50 mm dia each 645.15
1931 Brass full way valve with C.I. wheel (screwed end) 65 mm dia each 1123.81
1932 Brass full way valve with C.I. wheel (screwed end) 80 mm dia each 1685.72
1933 Gunmetal non-return valve-horizontal (screwed end) 25 mm dia each 343.39
1934 Gunmetal non-return valve-horizontal (screwed end) 32 mm dia each 468.26
1935 Gunmetal non-return valve-horizontal (screwed end) 40 mm dia each 582.71
1936 Gunmetal non-return valve-horizontal (screwed end) 50 mm dia each 853.26
1937 Gunmetal non-return valve-horizontal (screwed end) 65 mm dia each 1550.44
1938 Gunmetal non-return valve-horizontal (screwed end) 80 mm dia each 2206.00
1940 C.I.sluice valve (with caps) class I : 100 mm dia each 2507.76
1941 C.I.sluice valve (with caps) class I : 125 mm dia each 2705.46
1942 C.I.sluice valve (with caps) class I : 150 mm dia each 3746.03
1943 C.I.sluice valve (with caps) class I : 200 mm dia each 7804.24

BCD/SOR_8th Edition_October 2016 22

 Present
Code No Description Unit
Approved rate
1 2 3 4
1944 C.I.sluice valve (with caps) class I : 250 mm dia each 11425.40
1945 C.I.sluice valve (with caps) class I : 300 mm dia each 16128.75
1947 Vitreous china flat back wash basin 630x450 mm each 754.41
1949 Vitreous china angle back wash basin 600x480 mm each 754.41
1950 Vitreous china angle back wash basin 400x400 mm each 442.24
1951 C.P. brass waste 32 mm each 83.25
1952 C.P. brass waste 40 mm each 98.85
1953 Vitreous china Indian type w.c. pan size 580 mm each 468.26
1954 Vitreous china orrisa type w.c. pan size 580 mm each 811.64
1955 Vitreous china pedestal type water closet each 728.39
1956 Bolts and nuts 16 mm dia 60 mm long each 12.48
1957 Bolts and nuts 16 mm dia 65 mm long each 12.48
1958 Bolts and nuts 20 mm dia 65 mm long each 15.61
1959 Bolts and nuts 20 mm dia 70 mm long each 15.61
1960 Bolts and nuts 20 mm dia 75 mm long each 16.65
1961 Bolts and nuts 20 mm dia 80 mm long each 18.73
1962 Bolts and nuts 24 mm dia 85 mm long each 29.14
1963 Bolts and nuts 24 mm dia 90 mm long each 33.30
1964 Bolts and nuts 27 mm dia 100 mm long each 39.54
1965 White vitreous china dual purpose closet (Anglo Indian W.C.) each 1352.73
suitable for use as squatting pan or European type water closet
as per manufacturer's specifications
1970 Vitreous china foot rests 250x125x25 mm pair 104.06
1980 Fly ash cum 8.06
1984 Brick Tiles (300mm x 150mm x 50mm) thousand 6727.35
A Uraban Patna 7019.25
B For Purnia,Bhagalpur,Saharasa,Munger,Darabhanga 7049.70
C For Purnea 7373.10
D For other places 6727.35
1986 Common burnt clay modular bricks class designation 12.5 1000 nos 7019.25
2391 Strips-Aluminium fluted 3.15 mm thick and 150 mm wide metre 237.24
2392 Strips-Aiuminium fluted 3.15 mm thick and 200 mm wide metre metre 336.11
2393 1 mm thick Stainless Steel Cover plate grade 304 Kg 286.16
2394 Coupler 16 mm dia each 69.71
2395 Coupler 20 mm dia each 91.57
2396 Coupler 25 mm dia each 135.27
2397 Coupler 28 mm dia each 199.79
2398 Coupler 32 mm dia each 240.37
2399 Complete Roof Joint of 100 mm metre 4682.54
2400 Complete Roof Joint of 150 mm metre 4994.71

23 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
2401 Complete Roof Joint of 200 mm metre 5202.82
2402 Epoxy adhesive kg 156.08
2403 Floor Joint of 100 mm metre 4682.54
2404 Floor Joint of 150 mm metre 5202.82
2405 Floor Joint of 200 mm metre 5619.05
2406 Float glass sheet of nominal thickness 4 mm (weighing not less sqm 343.39
than 10 kg/sqm)
2407 Float Glass sheet of nominal thickness 5.5mm (weighing not less sqm 520.28
than 13.50 kg/sqm
2408 Float glass sheet of nominal thickness 8 mm (weight not less sqm 728.39
than 20.00 kg/sqm)
2409 Wall Joint of 100 mm metre 3537.92
2410 Wall Joint of 150 mm metre 3850.09
2411 Wall Joint of 200 mm metre 4162.25
2412 Ply wood 5 ply with commercial ply on both faces 6 mm thick sqm 374.61
2413 12 mm commercial ply sqm 603.53
2414 18 mm thick block board with commercial ply veneering on both sqm 728.39
side
2447 Hollock bailies 125 mm diameter metre 36.42
2449 Oxidised mild steel Pull bolt lock of size 85mmx42mm with each 52.02
screws bolts and washers complete
2451 Brass Cupboard lock 6 levers (best make of approved quality) 40 each 72.84
mm size
2452 Brass Cupboard lock 6 levers (best make of approved quality) 50 each 78.04
mm size
2453 Brass Cupboard lock 6 levers (best make of approved quality) 65 each 83.25
mm size
2454 Brass Cupboard lock 6 levers (best make of approved quality) 75 each 104.06
mm size
2455 Brass Hanging type door stopper 150 mm each 67.64
2456 Hydraulic door closer tubular type aluminium die cast body with each 613.94
necessary accessories and screws complete
2459 Anodised Aluminium hanging type door stopper each 26.02
2464 Anodised Aluminium pull boit lock (locking bolt) of size 85x42 each 52.02
mm with screws, bolts, nuts and washers complete
2465 Anodised Aluminium Casement stay 250 mm each 52.02
2466 Hollock wood in scantling 10 cud 338.18
2467 Chromium plated Brass Pull bolt lock (locking bolt) of size 85mm each 171.70
x 42mm with screws, bolts, nuts and washers complete

2468 Chromium Brass cupboard lock (Nickled) 40mm size each 67.64
2469 Chromium Brass cupboard lock (Nickled) 50mm size each 78.04
2470 Chromium Brass cupboard lock (Nickled) 65mm size each 88.45
2471 Chromium Brass cupboard lock (Nickled) 75mm size each 114.46
2480 PANELS Ply wood 5 ply with teak ply on both faces 9 mm thick sqm 1071.78

2481 Ply wood 5 ply with teak ply n one face and commercial ply on sqm 874.08
another face 9 mm thick
2483 Ply wood 7 ply with teak ply on one face and commercial ply on sqm 957.32
another face 9 mm thick

BCD/SOR_8th Edition_October 2016 24

 Present
Code No Description Unit
Approved rate
1 2 3 4
2484 Pre-laminated with decorative lamination on both side exterior sqm 719.97
Grade - I MDF Board 12 mm thick confirming to IS:14587

2485 Pre-laminated with decorative lamination on both side exterior sqm 959.92
Grade - I MDF Board 18 mm thick confirming to IS:14587

2486 Pre-laminated with decorative lamination one side and other side sqm 1246.75
balancing lamination exterior Grade - I MDF Board 25 mm thick
confirming to IS:14587
2487 Pre-laminated with decorative lamination one side and other side sqm 667.26
balancing lamination exterior Grade - I MDF Board 12 mm thick
confirming to IS:14587
2488 Pre-laminated with decorative lamination one side and other side sqm 895.57
balancing lamination exterior Grade - I MDF Board 18 mm thick
confirming to IS:14587
2489 PVC edge bending tape 2.00 mm thick metre 29.71
2500 Extra for selected planks of second class deodar wood 10 cud 104.06
2504 Kiln seasoning of timber cum 759.61
2505 Hollock wood in planks 10 cud 385.01
2506 Carben Steel galvanised dash fastner (min 5 micron) of 10 mm 10 cudm 260.14
dia double threaded 6.8 grade counter sunk head screw
comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10
mm x 60 mm
2507 Carben Steel galvanised dash fastner (min 5 micron) of 10 mm 10 nos 304.88
dia double threaded 6.8 grade counter sunk head screw
comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10
mm x 80 mm
2508 Carben Steel galvanised dash fastner (min 5 micron) of 10 mm 10nos 378.77
dia double threaded 6.8 grade counter sunk head screw
comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10
mm x 120mm
2509 Carben Steel galvanised dash fastner (min 5 micron) of 10 mm 10 nos 468.26
dia double threaded 6.8 grade counter sunk head screw
comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10
mm x 140 mm
2510 Carben Steel galvanised dash fastner (min 5 micron) of 10 mm 10 Nos 593.12
dia double threaded 6.8 grade counter sunk head screw
comprising of 10 mm dia polyamide PA 6 grade sleave. Size 10
mm x 160 mm
2602 Designation 100 A Brick thousand 5603.85
2602A Urban Patna thousand 7019.25
2602B Darbhanga thousand 5923.05
2602C Bhagalpur thousand 5923.05
2602D Munger thousand 5923.05
2602E Muzaffarpur thousand 5923.05
2602F Gaya thousand 5603.85
2602G Patna Rural thousand 5844.30
2602H Saran thousand 5603.85
2602I Saharsa thousand 6083.70
2602J Purnea thousand 6406.05
2603 Designation 100 B Brick thousand 5119.80

25 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
2603A Urban Patna thousand 6514.20
2603B Darbhanga thousand 5440.05
2603C Bhagalpur thousand 5440.05
2603D Munger thousand 5440.05
2603E Muzaffarpur thousand 5440.05
2603F Gaya thousand 5119.80
2603G Patna Rural thousand 5340.30
2603H Saran thousand 5119.80
2603I Saharsa thousand 5603.85
2603J Purnea thousand 5923.05
2605 Structural sealant - 6 mm x 12 mm metre 32.88
2606 Spacer tape 6.4 mm thick x 6 mm wide metre 18.73
2607 Weather Sealant - Non Staining (600 ml) each 477.77
2608 Weather Sealant - Normal (300 ml) each 149.01
2609 MS Brackets/Aluminium Alloy Brackets kg 104.06
2610 Silicon Gasket in Kg (Above 50 g / m) kg 625.64
2611 EPDM Gasket in Kg (Above 60 g / m) kg 166.49
2612 Anchor Fastner - M10 each 115.45
2613 SS Bolt with washer of sizes for structural glazing / ACP each 36.42
Cladding
2614 SS Screws of sizes for structural glazing / ACP Cladding each 5.21
2615 Protective Tape metre 26.02
2616 GI flashing - 1.2 mm Thick kg 68.68
2617 6 mm thick High performance glass sqm 1987.48
2618 6 mm thick clear heat strengthened glass sqm 801.23
2619 6 mm thick clear heat strengthened glass each 150.89
2620 ARMS GS HD -TOP HUNG -20"-TYPE P-COUPLE pair 1634.52
2621 Connection Block each 40.94
2622 Curtain wall striker each 106.87
2623 Adjustable Fastening Pawl each 39.80
2624 Corner drive each 306.91
2625 Top wedge Block each 142.08
2626 Glass wool Denisity 48 Kg / m3 with Black Glass Tissue (BGT) sqm 239.33
2627 SS Screws - # 8 x 19 each 10.40
2628 Weather Sealant - DC 789 cartridge 140.48
2629 Cement Board sqm 260.14
2630 Baker rod metre 5.21
2631 4 mm thick ACP sqm 1248.67
2632 Fire Stop metre 584.75
2634 GI/Aluminium Sheet (0.8 mm thick) kg 59.31
2704 Aluminium strip 40 mm wide and 2 mm thick kilogran 228.93
2708 Truf Paver (500 x 500 x 40 mm) sqm 1134.22
2709 Ceremic Tiles Pieces for Crazy Flooring quintal 140.48
2710 White Marble Makrana second quality plain veined stone pieces quintal 145.68
for crazy flooring
2711 FS800H Grade Flooring Panel ( Size 600 mm x600 mm x32 mm) each 780.42

BCD/SOR_8th Edition_October 2016 26

 Present
Code No Description Unit
Approved rate
1 2 3 4
2711' Sheets Polyvinyl chloride sheet 1.5 mm thick sqm 492.78
2712' Sheets Polyvinyl chloride sheet 2.0 mm thick sqm 683.35
2712 Zinc Electroplated Pedestals - 300 mm each 145.68
2713 Zinc Electroplated Pedestals - 450 mm each 156.08
2714 Zinc Electroplated Tube Stinger each 72.84
2715 Machine Screw for Fixing each 2.08
2717 Polyvinyl chloride tiles 1 5mm thick sqm 562.09
2718 Polyvinyl chloride tiles 2.0mm thick sqm 673.72
2723 Adhesive (rubber base) ilogran 182.86
2736 Sheets Rubber tiles plain conforming to IS 809 1.5 mm thick sqm 814.24
2737 Sheets Rubber tiles plain conforming to IS 809 2.0 mm .thick sqm 941.28
2738 Sheets Rubber tiles LP stud conforming to IS 809 2.0 mm thick sqm 814.24
2739 Sheets Rubber tiles LP stud conforming to IS 809 3.0 mm thick sqm 1393.64
2740 Sheets Rubber tiles LP stud conforming to IS 809 4.0 mm thick sqm 1847.91
2741 Sheets Anti static rubber tiles p!ain/LP stud conforming to BS : sqm 1509.13
2050 2.00 mm thick
2742 Sheets. Rubber tiles piain/LP stud in skirting conforming to IS : sqm 592.87
809 2.0mm thick
2750 8mrn thick granite stone tiles (mirror polished of all shades) sqm 728.39
2751 8mm thick marble tiles (polished) Raj Nagar sqm 374.61
2901 Stone Aggregate (Single size) : 100 mm nominal size cum 424.23
2902 Stone Aggregate (Single size) : 80 mm nominal size cum 424.23
2903 Stone chippings/ screenings 4.75 mm nominal size cum 213.24
2904 Stone chippings/ screenings 150 micron nominal size cum 201.63
2908 Over burnt (Jhama) Brick Aggregate: 120 mm to 40 mm size cum 1378.65
2909 Over burnt (Jhama) Brick Aggregate: 90 mm to 40 mm size cum 1378.65
2910 Stone chippings/ screenings 12.5/ 13.2 mm nominal size cum 689.78
2911 Stone chips/streining 10/11.2 mm nominal size cum 659.07
2914 Solvent kilogram 26.02
2916 Paving Asphalt VG -10 of approved quality tonne 41622.58
3002 Sheets Polyvinyl chloride sheet 400 micron thick sqm 36.42
3004 Stoneware spouts 100mm dia 60 em long each 36.42
GC Sheet
3050 Galvanised steel corrugated sheets 0.63 mm thick quintal 4827.90
3050A Galvanised steel corrugated sheets 0.50 mm thick quintal 5007.45
3050B Gah-anised steel corrugated sheets 0.40 mm thick quintal 6806.84
3050C Galvanised steel corrugated sheets 0.35 mm thick quintal 6806.84
3050D Galvanised steel corrugated sheets 0.80 mm thick quintal 4827.90
3080 Gunmetal non-return valve-vertical (screwed end) 25 mm dia each 374.61
3084 Gunmetal non-return valve-vertical (screwed end) 32 mm dia each 541.09
3088 Gunmetal non-return valve-vertical (screwed end) 40 mm dia each 780.42
3092 Gunmetal non-return valve-vertical (screwed end) 50 mm dia each 1050.97
3096 Gunmetal non-return valve-vertical (screwed end) 65 mm dia each 1779.36
3213 Vitreous china Surgeon type wash basin of size 660x460 mm each 1144.62
3214 Aluminium sheet 24 gauge sqm 336.86

27 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
3228 600x120 mm glass shelf with anodised aluminium angle frame, each 260.14
C.P. brass brackets and guard rail of standard size
3229 Vitreous china flat back wash basin 550x400 mm each 572.31
3300 Gunmetal non-return valve-vertical (screwed end) 80 mm dia each 3007.24
3311 C.I.sluice valve (with caps) class II : 100 mm dia each 3028.04
3314 C.I.sluice valve (with caps) class II : 125 mm dia each 3641.97
3317 C.I.sluice valve (with caps) class II : 150 mm dia each 4474.43
3320 C.I.sluice valve (with caps) class II : 200 mm dia each 9583.60
3321 C.I.sluice valve (with caps) class II : 250 mm dia each 15400.36
3326 C.I.sluice valve (with caps) class II : 300 mm dia each 19250.44
3327 15 mm Battery Based Sensor Pillar Cock each 6058.17
3617 CP Brass Union 40 mm dia each 202.91
3620 C.C.I.(spun) socketed soil, waste and vent pipe 1.80 metres long each 1300.71
:100 mm dia
3621 C.C.I. (spun) socketed soil, waste and vent pipe 1.80 metres each 1076.99
long :75 mm dia
3624 S.C.I. S&S bends with access door 100 mm dia each 301.76
3625 S.C.I. S&S bends with access door 75 mm dia each 249.74
3628 S.C.I. S&S bend 100 mm dia each 275.75
3629 S.C.I. S&S bend 75 mm dia each 202.91
3634 S.C.I. S&S heel rest sanitary bend 100 mm dia each 308.01
3635 S.C.I. S&S heel rest sanitary bend 75 mm dia each 260.14
3640 S.C.I. S&S single equal junctions100x100x100 mm each 491.15
3641 S.C.I. S&S single equal junctions 75x75x75 mm each 343.39
3644 S.C.I. S&S single equal junctions with access door 100x100x100 each 515.08
mm
3645 S.C.I. S&S single equal junctions with access door 75x75x75 each 388.13
mm
3650 S.C.I. S&S double equal junctions 100x100x100x100 mm each 645.15
3651 S.C.I. S&S double equal junctions 75x75x75x75 mm each 480.74
3654 S.C.I. S&S double equal junctions with access door each 639.94
100x100x100x100 mm
3655 S.C.I. S&S double equal junctions with access door each 499.47
75x75x75x75 mm
3660 S.C.I. S&S single unequal junctions 100x100x75 mm each 593.12
3664 S.C.I. S&S single unequal junctions with access door each 665.96
100x100x75 mm
3670 S.C.I. S&S double unequal junctions 100x100x75x75 mm each 832.45
3674 S.C.I. S&S double unequal junctions with access door each 884.48
100x100x75x75 mm
3681 S.C.I. S&S single equal invert branch of required degree each 442.24
100x100x75x75 mm dia
3682 S.C.I. S&S single equal invert branch of required degree each 336.11
75x75x75 mm dia
3685 S.C.I. S&S double equal invert branch of required degree each 551.50
100x100x100x100 mm dia
3686 S.C.I. S&S double equal invert branch of required degree each 442.24
75x75x75x75 mm dia

BCD/SOR_8th Edition_October 2016 28

 Present
Code No Description Unit
Approved rate
1 2 3 4
3690 S.C.I. S&S single unequal invert branch of required degree each 567.11
100x100x75 mm dia
3695 S.C.I. S&S double unequal invert branch of required degree each 754.41
100x100x75x75 mm dia
3699 S.C.I. S&S, 75 mm offset for 75 mm dia pipe each 234.12
3707 S.C.I. S&S, 150 mm offset for 75 mm dia pipe each 296.56
3708 S.C.I. S&S, 150 mm offset for100 mm dia pipe each 405.82
3712 S.C.I. S&S, 114 mm offset for 75 mm dia pipe each 312.17
3713 S.C.I. S&S, 114 mm offset for 100 mm dia pipe each 398.54
3716 S.C.I. S&S,152 mm offset for 75 mm dia pipe each 372.52
3717 S.C.I. S&S, 152 mm offset for 100 mm dia pipe each 483.86
3728 S.C.I. S&S, door pieces 100 mm dia each 416.22
3729 S.C.I. S&S, door pieces 75 mm dia each 306.97
3733 S.C.I. S&S, Slotted Cowl (Terminal Guard) 100 mm each 364.20
3734 S.C.I. S&S, Slotted Cowl (Terminal Guard) 75 mm each 312.17
3738 S.C.I. S&S, Slotted collars 100 mm each 260.14
3739 S.C.I. S&S, Slotted collars 75mm each 176.89
3746 S.C.I. S&S, 75 mm offset for 75 mm dia pipe each 226.84
3747 S.C.I. S&S, 75 mm offset for100 mm dia pipe each 377.73
3749 Vitreous china toilet paper holder of standard size each 156.08
3860 560 mm dia cover with frame (Heavy duty) each 9365.08
3861 561 mm dia cover without frame (Heavy duty) each 5202.82
4001 Stainless steel (Grade-304)hollow section round/square tubes kg 364.20
4002 Stainless steel bolts/square bar and plates kg 135.27
4006 Pressed steel door frames (mild steel sheet 1.25mm) profile 'B' metre 228.93
4007 Pressed steel door frames (mild steel sheet 1.25mm) profile 'C metre 249.74
4008 Pressed steel door frames (mild steel sheet 1.25mm) profile 'E' metre 280.95
4009 Mild steel tubes, hot finished welded type kilogram 54.11
4010 Mild steel tubes, hot finished seamless type kilogram 67.64
4011 Mild steel tubes, electric resistant or induction butt welded kilogram 72.84
4012 Circular C.I. box for ceiling fan each 62.43
4013 Pulleys 40 mm dia each 31.21
4014 Steel doors and windows Ready made steel door with necessary sqm 2081.86
hinges, lugs and glazing clips excluding other fittings and their
fixing
4201 Aluminium primer litre 104.06
4202 Primers Red Oxide Zinc Chromate primer litre 72.84
4203 Copper Accetate kilogram 312.17
4204 Hydrochloric Acid kilogram 36.42
4205 Copper Chloride kilogram 312.17
4206 Copper Nitrate kilogram 228.93
4207 Ammonium Chloride kilogram 20.81
5001 Oil / Fuel Mobil oil litre 208.12
6001 White marble slab Makrana second quality plain veined 18mm sqm 1945.86
thick

29 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
6007 Pink marble slab plain 18mm thick sqm 671.17
6010 Udaypur green marble slab plain 18 mm thick sqm 717.99
6019 Black zebra marble slab piain 18 mm thick sqm 520.28
6501 Local Sand (Ganga) cum 124.54
7001 Brass 100 mm mortice latch & lock with 6 levers with out pair of each 270.55
handles
7003 Pair of Anodised Aluminium lever handles for 100 mm mortice each 327.78
latch and lock
7004 Vitreous china flat back wash basin 550x400 mm each 442.24
7005 Vitreous china 10 litres low level cistern without fittings each 962.52
7006 Vitreous china 10 litres low level cistern with fittings each 1664.91
7007 Fly Ash Bricks as per IS 12894(2002) & IS 3425(I to IV) per 1000 5975.55
7008 F.P.S.(non modular) clay fly ash bricks class designation 7.5 1,000nos 4786.60
7009 Gypsum Board sqm 208.12
7010 Ceiling sections metre 40.59
7011 Perimetre channel metre 28.09
7012 Intermediate channel metre 43.71
7013 Ceiling angle metre 19.77
7014 Connecting clips each 6.46
7015 Soffit cleat each 4.16
7016 Joint filler kilogram 22.90
7017 Joint finisher kilogram 24.97
7018 Joint tape roll roll 150.89
7019 Dash fastner each 15.61
7020 All drive screws(for gypsum board ) 100 Nos. 62.43
7021 Primer (for gypsum uoard ) litre 88.45
7022 Chloropyriphos 20 % E.C. Lindane 20% E.C. litre 166.49
7023 Chromium plated orackets (Curtain rod) each 7.28
7024 Acid proof cement tonne 8480.60
7027 M.S. Butt hinges 125x90x4 mm ten 114.46
7028 12.5 mm thick Fully Perforated gypsum board sqm 964.60
7029 Galvanised wire mesh of average width of aperture 1.4 mm and sqm 260.14
romin31 dia. of wire 0.63 mm
7030 12.5 mm thick tapered edge gypsum fire resistant board sqm 246.62
7031 12.5 mm thick tapered edge gypsum moisture resistant board sqm 281.99
7032 Frosted glass sheet of nominal thickness 4mm (weighing not sqm 348.59
less than 10 kg/sqm)
7033 Nickle plated M.S. pipe 25 mm dia. metre 83.25
7034 Nickle plated M.S. pipe 20 mm dia. metre 72.84
7035 Nickle plated M.S. Brackets for curtain rod 20 mm each 7.28
7036 Nickle plated M.S. Brackets for curtain rod 25 mm each 8.33
7040 Oxidised mild steel screws 35 mm 100 Nos. 52.02
7042 Mild steel conduit pipe (heavy type) ISI marked-20 mm dia. metre 62.43
7043 Mild steel conduit pipe (heavy type) ISI marked-25 mm dia. metre 72.84
7044 Rolling shutters of 80xO.90mm laths sqm 1123.81
7045 Rolling shutters of 80x1.2mm laths sqm 1196.65

BCD/SOR_8th Edition_October 2016 30

 Present
Code No Description Unit
Approved rate
1 2 3 4
7046 Top cover of Rolling shutters 0.90mm thick metre 332.98
7047 Top cover of Rolling shutters 1.20mm thick metre 364.20
7048 Rawl plug 50 mm (designation 10 no.) each 10.40
7049 Teak wood lipping of size 25x3mm in pelmets metre 22.90
7050 PU Primer sqm 42.66
7051 40 mm (average) PU spray having 40-45 kg/m3 density sqm 438.08
7052 GI wire netting 3/4" x 24 G sqm 28.09
7053 400 G polythene sheet sqm 15.61
7055 Flat pressed 3 layer and graded particle board (medium density) sqm 437.03
Grade 1 conforming to IS : 3087 - 18 mm thick
7056 Aluminium Tee channel (heavy duty) with rollers and stop end metre 52.02
7059 Aluminium hanging floor door stopper with twin rubber & stopper each 67.64
7060 Hydraulic door closer tubular type Aluminium extruded section each 874.08
body - Gazel
7063 Oxidised M.S. casement stay (straight peg type) 300 mm not each 22.90
less than 0.33 kg.
7064 Oxidised M.S. casement stay (straight peg type) 250 mm not each 20.81
less than 0.28 kg.
7065 Oxidised M.S. casement stay (straight peg type) 200 mm not each 18.73
less than 0.24 kg.
7068 Extra for providing grilled rolling shutters with 8mm dia. M.S. sqm 280.95
7070 Chequerred precast cement concrete tiles 22mm thick using sqm 489.07
marble chips of size 6mm Light shade using white cement
7071 White marble Raj Nagar plain 18 mm thick upto 0.50 sqm area sqm 624.34
7072 Wall mounted water closet each 4838.62
7073 Adjustable Vetrious China Cistern with fittings each 2601.42
7074 White Vetrious China Waterless Urinal each 15608.46
7075 Cistern with fittings for Waterless Urinal each 3537.92
7076 White Vetrious Urinal each 14567.90
7077 Acid and alkali resistant tiles size 300x300mm 10mm thick ten 593.12
7087 S.C.I. Tee 150 mm each 624.34
7090 Expanded polystyrene type N - Normal sqm 135.27
7091 Expanded polystyrene type SE sqm 161.29
7095 Stainless steel kitchen sink - with drain board bowl depth 250 each 5395.33
mm
7096 Stainless steel kitchen sink - with drain board 510 x 1040 mm each 5150.80
bowl depth 225 mm.
7097 Stainless steel kitchen sink - with drain board 510 x 1040 mm each 4422.40
bowl depth 200 mm.
7098 Stainless steel kitchen sink - with drain board 510 x 1040 mm each 3121.69
bowl depth178 mm.
7101 Stainless steel kitchen sink - without drain board 610x510 mm each 3277.78
bowl depth 200 mm
7102 Stainless steel kitchen sink - without drain board 610x460 mm each 2960.41
bowl depth 200 mm
7103 Stainless steel kitchen sink - without drain board 470x420 mm each 2206.00
bowl depth 178 mm
7104 Coloured Orissa pattern W.C. pan 580x440 mm each 1373.54
7105 Coloured Pedestal type W.C. pan 580x440 mm (European type) each 1196.65

31 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
7106 Coloured Vitreous china 10 lit. low level cistern each 1789.77
7107 Coloured (other than black) solid P.V.C. seat in European W.C. each 572.31
pan
7112 Circular shape 450 mm dia Mirror with Plastic moulded frame each 468.26
7113 Rectangular shape 453x357 mm Mirror with Plastic moulded each 312.17
frame
7114 Oval shape 450x350 mm (outer dimensions) Mirror with each 364.20
Plasticmoulded frame
7115 Rectangular shape 1500x450 mm Mirror with Plastic moulded each 728.39
frame
7116 Hard board 6 mm thick each 182.10
7117 Semi Rigid PVC waste pipe for sink and wash basin 32 mm dia each 31.21
with length not less than 700 mm i/c PVC waste fittings
7118 Semi Rigid PVC waste pipe for sink and wash basin40 mm dia each 36.42
with length not less than 700 mm i/c PVC waste fittings
7119 Flexible (coil shaped) PVC waste pipe for sink and wash basin each 29.14
32 mm dia with length not less than 700 mm i/c PVC waste
fittings
7120 Flexible (coil shaped) PVC waste pipe for sink and wash basin each 31.21
40 mm dia with length not less than 700 mm i/c PVC waste
fittings
7123 Coloured High density polyethylene/ poly propylene 10 lit. (full each 712.79
flush) capacity controlled low level flushing cistern with fittings
7126 White Vitreous china 10 lit. (full flush) capacity controlled low each 1014.55
levelflushing cistern with all fittings
7127 Coloured Vitreous china 10 lit. (full flush) capacity controlled low each 1560.85
level flushing cistern with all fittings
7128 S.W. intercepting trap 100 mm dia each 197.70
7129 S.W. intercepting trap 150 mm dia each 260.14
7130 Rectangular shape 600x 450 mm precast R.C.C. manhole cover each 780.42
with frame - L.D. - 25
7131 Square shape 450x450 mm precast R.C.C. manhole cover with each 676.37
frame - L.D. - 25
7132 Circular shape 450 mm dia precast R.C.C. manhole cover with each 624.34
frame - L.D. - 25
7133 Rectangular shape 500x500 mm precast R.C.C. manhole cover each 728.39
with frame - M.D. - 10
7134 Circular shape 500 mm dia precast R.C.C. manhole cover with each 686.77
frame - M.D. - 10
7135 Circular shape 560 mm dia precast R.C.C. manhole cover with each 1144.62
frame - H.D. - 20
7136 Circular shape 560 mm dia precast R.C.C. manhole cover with each 1274.69
frame - H.D. - 35
7137 Factory made 35 mm thick shutters with laminated veneer sqm 1925.04
lumber styles rails as per TADS I S : 1995 and panels of 12 mm
thick plain Type I, medium density flat pressed three l?ver,
graded particle board (FPT-I) as per I S:3087-1985 bonded with
BWP type synthetic resin adhesive, as per IS : 848-1974

BCD/SOR_8th Edition_October 2016 32

 Present
Code No Description Unit
Approved rate
1 2 3 4
7139 Factory made 35 mm thick shutters with lamineted veneer sqm 2112.35
lumber styles rails as per TADS IS : 1995 and panels of 12 mm
thick both sides prelaminated Type -1, medium density flat
pressed three layer, graded particle board (FPT-I) IS: 3087
marked bonded with BWP type synthetic resin adhesive as per
IS : 848-1974 .
7143 12 mm thick one side prelaminated Type - I, other side balancing sqm 2029.10
lamination, medium density, flat pressed three layer, graded
particle board (FPT-I) as per IS : 3087, bonded with BWP type
synthetic resin as per IS : 848-1974 35 mm thick shutters

7151 Sheet glass using 10 kg I sqm glass panes 30 mm thick shutters sqm 1716.93

7154 Using galvanised wire gauge with average width of aperture 1.4 sqm 1696.12
mm on both direction with wire of dia. 0.63 mm 35 mm thick
shutters
7155 Using galvanised wire gauge with average width of aperture 1.4 sqm 1508.81
mm on both direction with wire of dia. 0.63 mm 30 mm thick
shutters
7157 Using galvanised wire gauge with average width of aperture 1.4 10 cudm 738.81
[Tim on both direction with wire of dia. 0.63 mm Laminated
veneer lumber conforming to TAOS 15 : 1995 manufactured in
factory in frames of door, windows
7178 Chemical ASTMC-type I kg 114.46
7181 C.I. pile shoe kilogram 52.02
7182 M.S. clamps for pile shoe kilogram 46.83
7183 Bentonite tonne 3225.75
7184 Oxidised M.S. safety chain (weighing not less than 450 gms) for each 62.43
each door
7187 C.I. grating 150 mm dia. (Weighing not less than 440 gm) each 26.02
7188 2 metre 69.71
U-PVC pipes (working pressure 4 kg/cm ) Single socketed ipe
75 mm dia
7189 2 metre 134.23
U-PVC pipes (working pressure 4 kg/cm ) Single socketed ipe
100 mm dia.
7190 2 metre 16.65
U-PVC pipes (working pressure 4 kg/cm ) Rubber (Seal) Ring 75
mm dia .
7191 2 metre 20.81
U-PVC pipes (working pressure 4 kg/cm ) Rubber (Seal ) Ring
100 mm dia .
7192 UPVC coupler for UPVC drainage pipes 75 mm each 35.38
7193 UPVC coupler for UPVC drainage pipes 110 mm each 54.11
7194 UPVC pushfit coupler (single) 75 mm thick each 52.02
7195 UPVC pushfit coupler (single) 110 mm thick each 84.28
7196 UPVC single equal Tee ( with door) 75x75x75 mm each 98.85
7197 UPVC single equal Tee (with door) 110x110x110 mm each 133.20
7198 UPVC single equal Tee ( with door) 75x75x75 mm each 119.66
7199 UPVC single equal Tee ( with door) 110x110x110 mm ecch 187.30
7208 UPVC bend 87.50 75 mm bend each 58.28
7209 UPVC bend 87.50 110 mm bend each 98.85
7212 UPVC plain shoe 75 mm each 111.34

33 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
7213 UPVC plain shoe 110 mm each 215.40
7214 UPVC pipe clip 75 mm bend each 16.65
7215 UPVC pipe clip 110 mm bend each 32.26
7231 Resin Bonded Glass wool 16 kg/m3, 50mm thick sqm 150.89
7232 Resin Bonded Glass wool 24 kg/m3, 50mm thick sqm 212.27
7233 Bitumen felt fibre base (vegetable or animal) Fibre glass tissue sqm 74.92
reinforced bitumen Felt Type 2 grade I conforming to IS : 7193

7236 Precast chequered cement tiles 22mm thick dark shade using sqm 239.33
ordinary cement
7237 Precast chequered cement tiles 22mm thick medium shade sqm 385.01
using 50% white cement, 50% ordinary cement
7238 High Albedo paint kg 255.98
7239 Epoxy paint litre 260.14
7240 Fire retardant paint litre 270.55
7241 Melamine polish litre 312.17
7244 Table rubbed polished stone 18mm thick (75x50 cm) Agaria sqm 1820.99
marble stone - 18 mm thick
7245 Table rubbed polished stone 18mm thick (75x50 cm) Granite sqm 1873.02
stone 18 mm thick
7246 Verticle load testing (INITIAL) of piles in accordance with IS : per test 34546.74
2911 (part-IV) including installation of loading platform and
prepration of pile head or construction of test cap and
dismantling of test cap after test etc. complete as per
specification & Upto 50 tonne capacity pile
7247 Verticle load testing (INITIAL) of piles in accordance with IS : per test 41934.74
2911 (part-IV) including installation of loading platform and
prepration of pile head or construction of test cap and
dismantling of test cap after test etc. complete as per
specification & Above 50 tonne & upto 100 tonne capacity pile:

7248 Verticle load testing (INITIAL) of piles in accordance with IS : per test 50467.37
2911 (part-IV) including installation of loading platform and
prepration of pile head or construction of test cap and
dismantling of test cap after test etc. complete as per
specification & Group of two more piles Upto 50 tonne capacity
piles.
7249 Cyclic vertical load testing of piles in accordance with IS: 2911 IV per test 15608.46
part including preparation of pile head etc. for Single piles Upto
50 tonne capacity tonne
7250 Cyclic vertical load testing of piles in accordance with IS: 2911 IV per test 23932.98
part including preparation of pile head etc. for Single piles Above
50 tonne capacity pile and upto 100 tonne capacity piles

7251 Cyclic vertical load testing of piles in accordance with IS : 2911 per test 30696.65
Part- IV) including preparation of pile head etc. for Group of two
piles up to 50 tonne capacity each
7252 Lateral load testing of singie pile in accordance with iS: 2911 per test 15608.46
Part - IV for determining safe allowable lateral load on pile. Upto
50 tonne capacity pile

BCD/SOR_8th Edition_October 2016 34

 Present
Code No Description Unit
Approved rate
1 2 3 4
7253 Lateral load testing of single pile in accordance with IS: 2911 per test 24557.32
Part - IV for determining safe allowable lateral load on pile.
Above 50 tonne capacity piie and upto 100 tonne capacity piles
7254 Hard crete compound litre 41.62
7255 Road marking paint (spirit based) litre 124.87
7256 Superior quality road marking paint litre 176.89
7257 C.P. Brass bibcock 15 mm each 390.21
7258 C.P. Brass long nose bibcock 15 mm each 683.65
7259 C.P. Brass long body bibcock 15 mm each 521.33
7260 C.P. Brass stop cock (concealed) 15 mm each 533.81
7261 C.P. Brass angle valve 15 mm each 433.91
7266 Pressed clay tiles 1000 nos. 12642.86
7267 Plain ceiling tiles (BWP type phenol formal dehyde synthetic each 124.87
resin bonded) (600x600x12mm)
7268 Semi perforated ceiling tiles (600x600x12mm) each 124.87
7269 25 mm thick particle board sqm 499.47
7270 30mm thick pre laminated flush door shutter sqm 884.48
7271 llnd class teak wood lipping 25mm wide x 12mm thick metre 41.62
7272 25 mm thick melamine faced prelaminated three layer particle sqm 978.13
board
7273 Resin Bonded Rockwool 48 kg/m3 sqm 219.56
7280 Waste plastic additive tonne 41622.58
7281 Chemical ASTMC-type II kg 176.89
7295 Granite of any colour, 18 mm thick (slab area upto 0.50 sqm) sqm 1977.07
7296 Granite of any colour, 30 mm thick (slab area upto 0.50 sqm) sqm 2393.30
7297 Granite of any colour,18 mm thick (slab area above 0.50sqm) sqm 2081.13
7306 Aluminium T or L sections kilogram 208.12
7307 For flush door shutters Extra for providing teak veneering on one sqm 353.80
side instead of commercial veneering
7309 Paving Asphalt of grade VG-30 of approved quality tonne 42663.14
7312 Expandable fastner with plastic sleeve and M.S. screws. 25 mm each 10.40
long
7313 Expandable fastner with plastic sleeve and M :S. screws. 32 long mm each 11.45
7314 Expandable fastner with plastic sleeve and M.S. screws. 40 long mm each 14.57
7315 Expandable fastner with plastic sleeve and M.S. screws. 50 long mm each 15.61
7318 Plasticizer/super plasticizer kilogram 39.54
7319 Wall form panel 1250X500mm each 1092.59
7320 Tie bolt 12mm dia 100 mm length each 52.02
7321 Tie bolt 12mm dia 150 mm length each 62.43
7322 Tie bolt 20mm dia 150 mm length each 78.04
7323 Tie bolt 20mm dia 225 mm length each 93.65
7324 Spring coil 12mm each 16.65
7325 Plastic cone 12mm dia each 18.73
7326 Corner angle 45x45x5mm 1.50 m long each 312.17
7327 100mm channel shoulder 2.5 m long each 1207.05
7328 Double clip (bridge clip) each 100.94

35 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
7329 Single clip each 80.12
7330 M.S. tube 40mm dia metre 291.36
7331 Wall form panel 1250x450mm each 1082.19
7332 Corner angle 45x45x5 mm 2.50 m long each 353.80
7333 Column clamp 450x1070 mm each 1269.49
7334 Prop 2 m ( 2-3.5m) each 863.67
7335 Binding wire kilogram 55.15
7338 Gun metal cramp kilogram 343.39
7339 Stainless steel cramp kilogram 353.80
7340 Stainless steel pin. kg 197.70
7342 Adjustable span ESQ+SI (2.35-3.40) each 1977.07
7343 Adjustable telescopic prop 3 m (2.00-3.75 m) each 1248.67
7344 Beam clamp 300-380mm (450-1070mm) each set 439.12
7345 Prop 4m each 1217.46
7346 Double coupler each 57.23
7347 Cadmium plated full threaded steei screws (30x4 mm dia.) 100 Nos. 29.14
7348 Aluminium Washer 2 mm thick 15 mm dia 100 Nos. 10.40
7349 12mm M.S. 'U' beading metre 15.61
7350 M S tower bolt bright finished / black stone enamelled 250x10 each 34.06
mm .
7353 M S tower bolt bright finished / black stone enamelled 100x10 each 23.69
mm
7354 Plastic encapsulated M.S. foot rest 30x20x15 cm each 119.66
7358 Flushing Cistern P.V.C. 10 lts capacity ( low level ) (White) ( with each 665.96
fittings, accessories and flush pipe)
7359 P.V.C. automatic flushing cistern 5 lts capacity each 509.88
7361 P.V.C. automatic flushing cistern 10 lts capacity each 551.50
7363 15 mm C.P. brass tap with elbow operation lever each 728.39
7364 White glazed fire clay draining board 600x450x25 mm each 572.31
7366 Glass reinforced Gypsum ( GRG) board 12.5 mm thick sqm 249.74
7367 Galvanised M.S. sheet 0.50mm thick pressed channel section of metre 62.43
size 50x32mm
7369 Galvanised M.S. sheet 0.50mm thick pressed stud 48x34x36mm metre 78.04
7375 G.I. flush pipe and C.P. brass spreader including C.P. each 483.86
connecting pipe Single lipped urinal
7376 G.I. flush pipe and C.P. brass spreader including C.P. each 1092.59
connecting pipe Range of two lipped urinals
7377 G.I. flush pipe and C.P. brass spreader including C.P. each 1300.71
connecting pipe Range of three lipped urinals
7378 G.I. flush pipe and C.P. brass spreader including C.P. each 1977.07
connecting pipe Range of four lipped urinals
7379 White vitreous china clay half stall urinal flat back 580x380x350 each 1664.91
mm or angle back 450x375x350 mm with waste fittings as per IS
: 2556
7380 Precast R.C.C. grating with frame 500x450 mm horizontal each 676.37
grating
7381 Precast R.C.C. grating with frame 450x100 mm vertical grating each 338.18
7382 Bitumen emulsion rapid setting (R.S.) confirming to IS : 8887 each 31008.82

BCD/SOR_8th Edition_October 2016 36

 Present
Code No Description Unit
Approved rate
1 2 3 4
7385 3 mm thick translucent white acrylic plastic sheet sqm 593.12
7386 12 thick particle board ceiling tile sqm 270.55
7387 Spigot for standard jointing 46.83
7388 Dash hold fastener 12.5 mm dia, 40 mm long with 6 mm dia bolt each 52.02
7389 Anodising 15 microns on aluminium sections kilogram 41.62
7390 Neoprene / EPDM rubber gasket meter 26.02
7391 Anodising 25 microns onaluminiu sections kg 52.02
7392 Power coating 50 microns on aluminium sections kg 66.59
7393 Polyster powder coating 50 microns on aluminium sections kg 72.84
7394 Double action hydraulic floor spring with stainless steel cover each 1612.87
plate
7395 6 mm dia. M.S. adjustable hangers including clips (upto 1.2 m each 29.14
length)
7396 Double action hydraulic floor spring with brass cover plate each 1768.96
7397 Base Jack each 187.30
7398 Challies each 832.45
7399 cup locks each 83.25
7400 15 mm PTMT bib cock each 104.06
7401 15 mm PTMT bib cock with flange (fancy) each 145.68
7402 15 mm PTMT bib cock long body with flange each 166.49
7403 15 mm dia PTMT stop cock(male thread) each 104.06
7405 20 mm dia. PTMT stop cock each 135.27
7406 PTMT pillar cock each 166.49
7407 PTMT push cock 15 mm dia each 93.65
7408 PTMT push cock 12 mm dia 20 mm BSP each 83.25
7409 PTMT grating 100 mm dia each 32.26
7410 PTMT Pillar cock (fancy) 15mm foam flow each 234.12
7411 125 mm grating with waste hole each 43.71
7412 Rectangular type with openable circular lid 150 mm size 18 mm each 126.95
high with 100 mm dia (110 gm)
7415 Double acting air valve 50 mm each 4162.25
7416 Double acting air valve 80 mm each 5410.94
7417 Double acting air valve 100 mm each 7075.84
7418 Water meter (including testing charges) 80 mm each 2216.41
7419 Water meter (including testing charges) 100 mm each 3433.86
7420 Water meter (including testing charges) 150 mm each 5202.82
7421 Water meter (including testing charges) 200 mm each 5619.05
7422 Dirt box strainer 80 mm each 2923.99
7423 Dirt box strainer 100 mm each 4765.79
7424 Dirt box strainer 150 mm each 6045.67
7425 Dirt box strainer 200 mm each 8584.66
7426 Cat's eye each 187.30
7427 Water stop Serrated with central bulb (225 mm wide, 8-11 mm metre 431.84
thick)
7428 Water stop Dumb bell with central bulb metre 405.82

37 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
7429 Water stop Kicers metre 390.21
7430 Wedge expansion hold fastner 1/4" or 6 mm each 14.57
7431 Wedge expansion hold fastner 3/8" or 10 mm each 15.61
7432 Wedge expansion hold fastner 1/2" or 12 mm each 29.14
7439 8mm thick (mirror polished tiles machine cut edge) Raj Nagar sqm 520.28
white
7442 Wheel 75mm dia. 40mm wide each 67.64
7443 Aluminium single cleat of size 30x32x3 mm each 14.57
7444 Aluminium grip strip of size 50x12x2 mm each 11.45
7445 25 mm prelaminated flush door both side decorative sqm 863.67
7449 Aluminium U beading kilogram 228.93
7451 Glass sheet (Pin headed) 4mm thick sqm 312.17
7452 Raj Nagar plain- White Marble (table rubbed and polished 18mm sqm 676.37
thick slab area upto 0.50 sqm
7453 Raj Nagar plain- White Marble (table rubbed and polished 18mm sqm 780.42
thick slab area more than 0.50 sqm
7466 Second class deodar teak wood lipping 30mm width x 12mm metre 31.21
7468 Veneered particle board with commercial veneerinq on both sqm 520.28
sides 12 mm thick
7477 Prelaminated particle board with one side decorative and other sqm 770.02
side balancing lamination, flat presed 3 layer & graded (medium
density) Grade I. Type II conforming to IS : 12823 (exterior
grade) 12 mm thick
7478 Prelaminated particle board with one side decorative and other sqm 884.48
side balancing lamination, flat presed 3 layer & graded (medium
density) Grade I. Type II conforming to IS : 12823 (exterior
grade) 18 mm thick
7479 Prelaminated particle board with one side decorative and other sqm 967.72
side balancing lamination, flat presed 3 layer & graded (medium
density) Grade I. Type II conforming to IS : 12823 (exterior
grade) 25 mm thick
7480 Prelaminated particle board with both sides decorative sqm 811.64
lamination.flat pressed 3 layer & graded (medium density)
Graefe I. Type II conforming to IS : 12823 (exterior grade) 12
mm thick
7485 Oxidised M.S. hinges finished with nickle plating 50mm ( Over all metre 43.71
width)
7486 Oxidised M.S. hinges finished with nickle plating 65mm (Over all metre 56.19
width)
7491 PTMT - Waste Coupling 31/32 mm each 53.07
7492 PTMT - Waste Coupling 38/40 mm each 66.59
7493 PTMT - Bottle Trap 31/32 mm each 329.86
7494 PTMT - Bottle Trap 38/40 mm each 358.99
7495 PTMT - Ball Cock 15 mm Complete with Epoxy Coated each 139.44
Aluminium
Rod & H.D. Ball
7496 PTMT - Ball Cock 20mm Complete with Epoxy Coated each 202.91
Aluminium
Rod & H.D. Ball

BCD/SOR_8th Edition_October 2016 38

 Present
Code No Description Unit
Approved rate
1 2 3 4
7497 PTMT - Ball Cock25 mm Complete with Epoxy Coated each 437.03
Aluminium
Rod & H.D. Ball
7498 PTMT - Ball Cock 40 mm Complete with Epoxy Coated each 811.64
Aluminium
Rod & H.D. Ball
7499 PTMT - Ball Cock 50 mm Complete with Epoxy Coated each 1196.65
Aluminium
Rod & H.D. Ball
7500 PTMT - Angle Stop cock with Flange 15 mm each 135.27
7501 PTMT - Swiveling shower 15 mm each 90.53
7503 PTMT - Liquid Soap Container of 400 ml capacity each 150.89
7504 PTMT - Towel Ring 215x200x37 mm each 120.70
7505 PTMT - Towel Rail (450 mm) each 199.79
7506 PTMT - Towel Rail (600 mm) each 235.17
7507 PTMT - Shelf 450x124x36 mm each 268.47
7508 PTMT - Urinal Spreader 15 mm each 132.15
7509 PTMT - Soap Dish/Holder 138x102x75 mm each 124.87
7512 PTMT - handle 125x34x24 mm each 31.21
7513 PTMT - handle 150x34x24 mm each 35.38
7514 PTMT - butt hinges 75x60x10 mm each 43.71
7515 PTMT - butt hinges 100x75x10 mm each 58.28
7516 PTMT - Tower bolt 152x42x18 mm each 67.64
7517 PTMT - Tower bolt 202x42x18 mm each 83.25
7518 PTMT - door catcher 72x42 mm each 28.09
7552 Coir Veneered board 4 mm thick sqm 301.76
7553 Coir Veneered board 6 mm thick sqm 405.82
7555 Coir Veneered board 12 mm thick sqm 676.37
7556 Coir Veneered board 18 mm thick sqm 1071.78
7651 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 100 mm dia metre 832.45
7652 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 150 mm dia metre 1248.67
7653 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 200 mm dia metre 1716.93
7654 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 250 mm dia metre 2393.30
7655 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 300 mm dia metre 2976.01
7656 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 350 mm dia metre 3652.38
7657 Ductile Iron class K - 9 pipe Conforming to I.S. 8329400 mm dia metre 4682.54
7658 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 450 mm dia metre 5410.94
7659 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 500 mm dia metre 6846.91
7660 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 600 mm dia metre 8251.68
7661 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 700 mm dia metre 11446.21
7662 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 750 mm dia metre 12382.72
7663 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 800 mm dia metre 12486.77
7664 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 900 mm dia metre 15088.18
7665 Ductile Iron class K - 9 pipe Conforming to I.S. 8329 1000 mm metre 16961.19
dia

39 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
7666 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 100 ench 31.21
mm dia
7668 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 150mm ench 39.54
dia
7669 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 200mm ench 68.68
dia
7670 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 250mm ench 81.16
dia
7671 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 300 ench 119.66
mm dia
7672 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 350 ench 137.35
mm dia
7673 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 400 ench 249.74
mm dia
7674 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 450 ench 291.36
mm dia
7675 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 500 ench 317.37
mm dia
7676 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 600 ench 395.41
mm dia
7677 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 700 ench 598.32
mm dia
7678 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 750 ench 717.99
mm dia
7679 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 800 ench 790.83
mm dia
7680 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 900 ench 1040.57
mm dia
7681 Rubber Gaskets Conforming to I.S 5382 of S.B.R quality 1000 ench 1248.67
mm dia
7682 Ductile Iron K - 12 specials suitable for push on jointing upto 600 quintal 13527.34
mm dia
7683 Ductile Iron K - 12 specials suitable for push on jointing over 600 quintal 18730.16
mm dia
7684 Ductile Iron specials suitable for mechanical jointing as per I.S. quintal 14255.73
9523 - upto 600 mm dia
7685 Ductile Iron Specials suitable for mechanical jointing as per I.S. quintal 20447.09
9523 over 600 mm dia
7686 Ductile Iron Pipe Class K-9 flanges and welding 100 mm dia metre 2268.43
7687 Ductile Iron Pipe Class K-9 flanges and welding 150 mm dia metre 3641.97
7688 Ductile Iron Pipe Class K-9 flanges and welding 200 mm dia metre 4276.72
7689 Ductile Iron Pipe Class K-9 flanges and welding 250 mm dia metre 3563.93
7690 Ductile Iron Pipe Class K-9 flanges and welding 300 mm dia metre 7242.32
7691 Ductile Iron Pipe Class K-9 flanges and welding 350 mm dia metre 9156.97
7692 Ductile Iron Pipe Class K-9 flanges and welding400mm dia metre 11040.39
7693 Ductile Iron Pipe Class K-9 flanges and welding 450 mm dia metre 13423.28
7694 Ductile Iron Pipe Class K-9 flanges and welding 500mm dia metre 15712.52
7695 Ductile Iron Pipe Class K-9 flanges and welding600mm dia metre 21466.84
7696 Ductile Iron Pipe Class K-9 flanges and welding700 mm dia metre 26638.45
7697 S&S Centrifugally (Spun) C.I. Pipe class LA 100 mm dia metre 936.51
7698 S&S Centrifugally (Spun) C.I. Pipe class LA 125mm dia metre 1165.43

BCD/SOR_8th Edition_October 2016 40

 Present
Code No Description Unit
Approved rate
1 2 3 4
7699 S&S Centrifugally (Spun) C.I. Pipe class LA 150 mm dia metre 1404.77
7700 S&S Centrifugally (Spun) C.I. Pipe class LA 200 mm dia metre 2393.30
7701 S&S Centrifugally (Spun) C.I. Pipe class LA 250 mm dia metre 3121.69
7702 S&S Centrifugally (Spun) C.I. Pipe class LA 300 mm dia metre 4214.29
7703 S&S Centrifugally (Spun) C.I. Pipe class LA 350mm dia metre 5046.74
7704 S&S Centrifugally (Spun) C.I. Pipe class LA 400mm dia metre 6659.61
7705 S&S Centrifugally (Spun) C.I. Pipe class LA 450 mm dia metre 8064.38
7706 S&S Centrifugally (Spun) C.I. Pipe class LA500 mm dia metre 9365.08
7707 S&S Centrifugally (Spun) C.I. Pipe class LA 600 mm dia metre 13105.91
7708 S&S Centrifugally (Spun) C.I. Pipe Specials as per IS 1538 quintal 5671.08
suitable for lead jointing up to 300 mm dia
7709 S&S Centrifugally (Spun) C.I. Pipe Specials as per IS 1538 quintal 8532.63
suitable for lead jointing over 300 mm dia
7710 S&S Centrifugally (Spun) C.I. Pipe specials suitable for quintal 9365.08
mechanical joint as per I.S. 13382 up to 300 mm dia
7711 S&S Centrifugally (Spun) C.I. Pipe Specials suitable for quintal 9885.36
mechanical joint as per IS 13382 over 300 mm dia
7712 Screwed double flanged centrifugally cast (spun) C.I. Pipe of metre 1430.77
Class B conforming to I.S. 1536, - 100 mm dia
7713 Screwed double flanged centrifugally cast (spun) C.I. Pipe of metre 2237.22
Class B conforming to I.S. 1536, - 150 mm dia
7714 Screwed double flanged centrifugally cast (spun) C.I. Pipe of metre 3537.92
Class B conforming to I.S. 1536, - 200 mm dia
7715 Screwed double flanged centrifugally cast (spun) C.I. Pipe of metre 4266.31
Class B conforming to I.S. 1536, - 250 mm dia
7716 Screwed double flanged centrifugally cast (spun) C.I. Pipe of metre 5452.56
Class B conforming to I.S. 1536, - 300 mm dia
7717 Screwed double flanged centrifugally cast (spun) C.I. Pipe of metre 6867.73
Class B conforming to I.S. 1536, - 350 mm dia
7718 Screwed double flanged centrifugally cast (spun) C.I. Pipe of metre 8896.83
Class B conforming to I.S. 1536, - 400 mm dia
7719 Screwed double flanged centrifugally cast (spun) C.I. Pipe of metre 11342.15
Class B conforming to I.S. 1536, - 450 mm dia
7720 Screwed double flanged centrifugally cast (spun) C.I. Pipe of metre 14110.05
Class B conforming to I.S. 1536, - 500 mm dia
7721 Screwed double flanged centrifugally cast (spun) C.I. Pipe of metre 19562.61
Class B conforming to I.S. 1536, - 600 mm dia
7722 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 100 mm metre 806.44
dia
7723 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 150 mm metre 1165.43
dia
7724 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 200 mm metre 1612.87
dia
7725 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 250 mm metre 2185.18
dia
7726 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 300 mm metre 3017.64
dia
7727 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 350 mm metre 3584.74
dia
7728 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 400 mm metre 4177.87
dia

41 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
7729 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 450 mm metre 5048.81
dia
7730 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 500 mm metre 5967.63
dia
7731 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 600 mm metre 7783.42
dia
7732 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 700 mm metre 10002.94
dia
7733 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 800 mm metre 12590.83
dia
7734 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 900 mm metre 16721.87
dia
7735 Ductile Iron Class K- 7 pipe conforming to I.S. 8329 - 1000 mm metre 17722.90
dia
7736 Extruded burnt flyash clay sewer bricks conforming to I.S 4885 1000nos 5619.05
7737 Fly ash lime bricks (FALG Bricks) conforming to I.S. 12894 - 1000nos 4890.66
1989
7738 Calcium Silicate Bricks machine moulded confirming to I.S. 4139 1000nos 5202.82
7739 Modified Bitumen Refinery produced CRMB - 55 toone 42559.08
7741 Modified Bitumen Refinery produced CRMB - 60 toone 42455.03
7742 Bitumen emulsion medium setting (M.S.) conforming to IS : 8887 toone 31216.94
7743 M.S. pipe 150 mm dia casing pipe metre 1103.00
7744 M.S. pipe 200 mm dia casing pipe metre 1352.73
7745 PVC blind pipe 150 mm dia as per IS: 12818 metre 520.28
7746 PVC blind pipe 200 mm dia as per IS: 12818 metre 780.42
7747 M.S. cap 150 mm dia each 166.49
7748 M.S. cap 200 mm dia each 208.12
7749 M.S bail plug 150 mm dia each 208.12
7750 M.S bail plug 200 mm dia each 228.93
7751 PVC slotted pipe 150 mm dia as per IS: 12818 metre 468.26
7752 PVC slotted pipe 200 mm dia as per IS: 12818 metre 728.39
7753 Boulder 50 mm to 200 mm cum 364.20
7754 Gravel 5 mm to 10 mm cum 728.39
7755 Gravel 1.5 mm to 2 mm cum 676.37
7756 Gravel 3 mm to 6 mm cum 707.58
7757 M.S. pipe 100 mm dia casing pipe metre 801.23
7758 UPVC blind pipe 100 mm dia as per IS: 12818 metre 374.61
7759 UPVC slotted pipe 100 mm dia as per IS: 12818 metre 395.41
7760 M.S. cap 100 mm dia each 135.27
7761 M.S. bail plug 100 mm dia each 166.49
7762 Precast R.C.C. perforated slab each 832.45
7763 Water supply tanker of 5000 litre capacity each 832.45
7764 M.S. socket 100 mm dia each 187.30
7765 M.S. socket 150 mm dia each 228.93
7766 M.S. socket 200 mm dia each 291.36
7767 Stone cleaning chemical approved by ASI litre 171.70
7768 Water repallent chemical approved by ASI litre 1651.37

BCD/SOR_8th Edition_October 2016 42

 Present
Code No Description Unit
Approved rate
1 2 3 4
7769 Stone surface strengthening chemical approved by ASI litre 1061.38
7770 Turpentine oil litre 70.76
7771 Liquid Amonia 5% litre 167.53
7772 Pea Gravel cum 780.42
7773 Coloured inter locking C.C. paver Block sqm 520.28
7774 Stone size 10x10x7.50cm each 9.36
7775 Sodium pentachlorophenate kilogram 655.56
7800 Ceramic Glazed Tiles 1st Quality minimum thickness 5mm in all sqm 312.17
colours shades except Burgandy, Bottle Green, Black
7801 Ceramic Glazed Tiles 1st quality 300x300 mm in all shades & sqm 379.80
designs of White, Ivory, Fume Red Brown etc.
7802 Ceramic Glazed Tiles 1st quality 300x300 mm in all shades & sqm 390.21
designs except White, Ivory, Grey and Fume Red Brown etc.
7803 Ceramic Glazed Tiles 1st quality 300x300 or more in all shades sqm 535.90
designs White, Ivory, Grey and Fume Red Brown etc.
7804 Ceramic Glazed Tiles 1st quality 300x300 or more mm hi all sqm 567.11
shades designs except White, Ivory, Grey and Fume Red brown
etc.
7805 Salem Stainless steel AISI - 304 (18/8) Orrisa pattern W.C. pan each 3954.15
724 mm X 578 mm
7806 Salem Stainless steel AISI - 304 (18/8) Round basin 405 mm each 1925.04
X355 mm
7807 Salem Stainless steel AISI - 304 (18/8) Wash basin 530 mm X each 1716.93
345 mm each
7808 Centrifugally cast (spun) iron S&S 100 mm inlet and 100 mm each 452.65
outlet
7809 Centrifugally cast (spun) iron S&S 100 mm inlet and 75 mm each 486.98
outlet
7850 Agaria White marble slab plain 18 mm thick each 1165.43
7857 P.T.M.T. Grating square slit 150 mm each 80.12
7858 P.T.M.T. Urinal cock 15mm dia each 124.87
7859 P.T.M.T. Bib cock with nozzle 15 mm each 150.89
7861 P.T.M.T. Stop cock (concealed) 15 mm each 164.41
7862 15 mm nominal bore and 30 cm length PVC connection pipe each 33.30
with P.T.M.T. Nuts
7863 15 mm nominal bore and 45 cm length PVC connection pipe each 41.62
with P.T.M.T. Nuts
7864 P.T.M.T. extension nipple 15 mm each 33.30
7865 P.T.M.T. extension nipple 20 mm each 39.54
7866 P.T.M.T. extension nipple 25 mm each 59.31
7893 Tactile tile sqm 903.21
7895 Matt finished vitrified tile 100x100 x16 mm sqm 967.72
7896 Vitrified tile sqm 530.69
7900 Modular common burnt clay bricks of class designation 7.5 1,000nos 4682.54
7901 Machine moulded perforated common burnt clay FPS (non 1,000nos 4786.60
modular) bricks of class designation 12.5
7902 Machine moulded common burnt clay modular perforated bricks 1,000nos 4786.60
of class designation 12.5
7903 Machine moulded common burnt clay FPS (non modular) bricks 1,000nos 4682.54
of class designation 12.5
7904 Machine moulded common burnt clay tile bricks of class 1,000nos 5202.82
designation 12.5

43 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
8001 24 mm thick Factory made shutters with styles, rails and panels sqm 2237.22
of PVC extruded sections in white, grey or wooden finish
8002 30 mm thick Factory made shutters with styles, rails and panels sqm 2341.27
of PVC extruded sections in white, grey or wooden finish
8003 Factory made PVC rigid foam panelled door shutter 30 mm thick sqm 2237.22

8004 Factory made PVC rigid foam panelled shutters as per I S: 4020 sqm 2653.44
i/c carriage
8006 Factory made PVC rigid foam sheet 1 mm thick sqm 192.50
8007 Factory made PVC rigid foam sheet 5 mm thick sqm 657.63
8008 Factory made Prelaminated PVC rigid foam sheet 5 mm thick sqm 782.50
8010 Factory made PVC Door frame 48x40x1.5 mm in white , grey or metre 156.08
wooden finish
8011 Factory made door frame PVC extruded sheet i/c carriage metre 364.20
8012 Adhesive Solvent cement litre 171.70
8014 Factory made door frame of size 50x47 mm with wall thickness metre 509.88
5mm made of single piece extruded profile
8100 Powder coated M.S. Butt Hinges 100x58x1.9mm 10 Nos 88.45
8200 APP modified Polymeric felt 1.5 mm thick sqm 62.43
8201 APP modified Polymeric felt 2.0 mm thick sqm 103.02
8203 A P.P. modified 2 mm thick membrane reinforced with glass fibre sqm 173.77
matt.
8204 A.P.P. modified 3 mm thick membrane reinforced with glass fibre sqm 215.40
matt.
8205 A.P.P. modified 3 mm thick membrane reinforced with polyester sqm 254.93
matt.
8206 Bitumen primer for bitumat membrane. litre 85.33
8207 Geotextile 120 gsm membrane sqm 39.54
8210 Stainless Steel 50mm long Screws 100 Nos. 260.14
8211 Stainless Steel 40mm long Screws 100 Nos. 208.12
8212 Stainless Steel 30mm long Screws 100. Nos. 156.08
8214 Stainless Steel 20mm long Screws 100 Nos. 104.06
8215 Stainless Steel 125x64x1.90mm Butt Hinge IS: 12817 marked 10 Nos. 260.14
8216 Staialess Steel 100x58x1.90mm Butt Hinge IS : 12817 marked 10 Nos. 239.33
8217 Stainless Steel 75x47x1.80mm Butt Hinge IS : 12817 marked 10 Nos. 156.08
8218 Stainless Steel 50x37x1.50mm Butt Hinge IS: 12817 marked 10 Nos. 135.27
8219 Stainless Steel 125x64x2.50mm Butt Hinge IS: 12817 marked 10 Nos. 343.39
8220 Stainless Steel 100x60x2.50mm Butt Hinge IS:12817 marked 10 Nos. 249.74
8221 Stainless Steel 75x60x2.50mm Butt Hinge IS: 12817 marked 10 Nos. 202.91
8222 M. S. heavy weight butt hinges 125x90x4.00mm (heavy weight) 10 Nos. 343.39
IS: 1341 marked
8223 M. S. heavy weight butt hinges 100x75x3.50mm (heavy weight) 10 Nos. 176.89
IS: 1341 marked
8224 M.S. heavy weigh butt hinges 75x60x3.10mm (heavy weight) IS: 10 Nos. 93.65
1341 marked
8225 M.S. heavy weight butt hinges 50x40x2.50mm (heavy weight) IS: 10 Nos. 78.04
1341 marked
8300 1216 mm PE-AL-PE Composite pressure pipe metre 98.85

BCD/SOR_8th Edition_October 2016 44

 Present
Code No Description Unit
Approved rate
1 2 3 4
8301 1620 mm PE-AL-PE Composite pressure pipe metre 130.07
8302 2025 mm PE-AL-PE Composite pressure pipe metre 166.49
8303 2532 mm PE-AL-PE Composite pressure pipe metre 213.31
8304 3240 mm PE-AL-PE Composite pressure pipe metre 353.80
8305 4050 mm PE-AL-PE Composite pressure pipe metre 390.21
8501 Polymer modified cementation coating kilogram 140.48
8502 Fibre glass cloth sqm 45.78
8503 Fibre glass cloth sqm 48.85
8504 Multi surface paint litre 286.16
8505 Acralyc exterior paint litre 145.68
8506 Premium Acralyc exterior paint litre 244.53
8507 Textured exterior paint litre 208.12
8508 Primer for cement paint litre 81.16
8509 Special Primer (C.W.) litre 86.37
8510 Metal Primer (U.G.) litre 124.87
8589 Calcium Silicate tegular edged celling tiles 595x595 mm and sqm 892.80
15mm thick
8590 Galvanised Steel main Tee ceiling section Size 24x38x0.33 each 199.79
mm(3 metre long)
8591 Galvanised Steel perimeter wall Angle Size 24 x 24 x 0.40 mm each 130.07
(3.00 metre long)
8592 Galvanised Steel intermediate cross T section Size 24 x 25 each 80.12
x0.33 mm (1.2 metre long)
8593 Galvanised Steel intermediate cross T section Size 24 x 25 each 40.59
x0.33 mm ( 0.6 metre long)
8594 Galvanised Steel soffit cleat size 25x35x1.60 mm each 3.12
8595 Wooden screws with plastic rawl plugs 35x8 mm each 0.62
8597 GI Metal Tile Clip in Plain Beveled edge global white colour tiles sqm 931.30
of size 600x600 mm and 0.5 mm thick
8598 GI Metal Tile Clip in Perforated Beveled edge global white colour sqm 1040.57
tiles of size 600x600 mm and 0.5 mm thick
8599 GI Metal Tile Lay-in Plain Tegular edge global white color tiles of sqm 841.82
Size 595x595 mm and 0.5 mm thick
8600 GI Metal Tile Lay-in Perforated Tegular edge global white color sqm 942.75
tiles of Size 595x595 mm and 0.5 mm thick
8601 PVC Laminated Gypsum Tiles (Square edge) of Size 595x595 sqm 486.98
mm and 12.5 mm thick
8602 Gypsum Tiles Fully Perforated Square edge of Size 595x595 sqm 503.64
mm and 12.5 mm thick
8604 Spring T-section 24x34x0.45 mm (3.00 meter long) metre 187.30
8605 C Wall angle section 20x30x20x0.50 mm (3.00 meter long) metre 161.29
8606 Main C Carrier Size 10x38x10x0.70 mm (3.00 meter long) metre 170.65
8607 Spring T-connector each 5.21
8608 C Carrier Connector each 11.45
8609 C Suspension Clip each 11.45
8610 Wire Coupling Clip each 9.36
8611 Main T ceiling sections 24x38x0.3 mm (3 meter long) each 194.58
8612 Perimeter Wall angle 21 x21 mm ( 3 meter long) each 122.79

45 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
8613 Intermediate Cross Channel (1.2 mtrs) each 74.92
8614 Intermediate Cross Channel (1.6 mtrs) each 35.38
8615 Hanger rod 0.5 mm thick each 8.33
8616 Adjustment clip each 6.24
8617 Soffit Cleat each 3.12
8618 Dash fastener 6 mm dia 50 mm long each 11.45
8620 Vitrified floor tiles 50x50 cm sqm 775.22
8621 Vitrified floor tiles 60x60 cm sqm 915.70
8622 Vitrified floor tiles 80x80 cm sqm 1129.01
8623 Vitrified floor tiles 1 00x1 00 cm sqm 1716.93
8625 Poly propylene- Random - Co - Polymer (PPR) pipes SDR 7.4 - metre 38.50
16 mm Outer dia
8626 Poly propylene- Random - Co - Polymer (PPR) pipes SDR 7.4 - metre 59.31
20mm Outer dia
8627 Poly propylene- Random - Co - Polymer (PPR) pipes SDR 7.4 - metre 91.57
25mm Outer dia
8628 Poly propylene- Random - Co - Polymer (PPR) pipes SDR 7.4 - metre 147.76
32mm Outer dia
8629 Poly propylene- Random - Co - Polymer (PPR) pipes SDR 7.4 - metre 221.64
40mm Outer dia
8630 Poly propylene- Random - Co - Polymer (PPR) pipes SDR 7.4 - metre 346.51
50mm Outer dia
8631 Poly propylene- Random - Co - Polymer (PPR) pipes SDR 7.4 - metre 533.81
63mm Outer dia
8632 Poly propylene- Random - Co - Polymer (PPR) pipes SDR 7.4 - metre 728.39
75mm Outer dia
8633 Poly propylene- Random - Co - Polymer (PPR) pipes SDR 7.4 - metre 1109.25
90mm Outer dia
8634 Poly propylene- Random - Co - Polymer (PPR) pipes SDR -11- metre 1248.67
110 mm Outer dia
8635 Poly propylene- Random - Co - Polymer (PPR) pipes SDR-11 - metre 2601.42
160mm Outer dia
8636 Chlorinated Polyvinyl - chloride (CPVC) pipe 15 mm outer dia metre 57.23
8637 Chlorinated Polyvinyl - chloride (CPVC) pipe 20 mm outer dia metre 70.76
8638 Chlorinated Polyvinyl - chloride (CPVC) pipe 25 mm outer dia metre 98.85
8639 Chlorinated Polyvinyl - chloride (CPVC) pipe 32 mm outer dia metre 135.27
8640 Chlorinated Polyvinyl - chloride (CPVC) pipe 40 mm outer dia metre 192.50
8641 Chlorinated Polyvinyl - chloride (CPVC) pipe 50 mm outer dia metre 312.17
8642 Chlorinated Polyvinyl - chloride (CPVC) pipe 62.5 mm inner dia metre 946.91
8643 Chlorinated Polyvinyl - chloride (CPVC) pipe 75 mm inner dia metre 1352.73
8644 Chlorinated Polyvinyl - chloride (CPVC) pipe 100 mm inner dia metre 1873.02
8645 Chlorinated Polyvinyl - chloride (CPVC) pipe 150 mm inner dia metre 2237.22
8646 Silicon sealant cartridge 319.45
8647 Stainless steel screws 30mmx4mm cent 30.18
8648 Hermetically sealed double glazed unit made with 6mm thick sqm 2382.89
clear float glass both side having 12 mm air gap
8649 Stainless steel (ss 304 grade) adjustable friction windows stay each 178.98
205x19mm

BCD/SOR_8th Edition_October 2016 46

 Present
Code No Description Unit
Approved rate
1 2 3 4
8650 Stainless steel (ss 304 grade) adjustable friction window stay each 223.72
255x19mm
8651 Stainless steel (ss 304 grade) adjustable friction window stay each 286.16
355x19mm
8652 Stainless steel (ss 304 grade) adjustable friction window stay each 509.88
510x19mm
8653 Stainless steel (ss 304 grade) adjustable friction window stay each 884.48
710x19mm
8654 Masking tape metre 2.60
8655 Autoclaved aerated cement (AAC) blocks. cum 2453.37
8656 Gypsum panel 666x500x100 mm size sqm 499.47
8657 Bonding laster for gypsum panel. kg 57.23
8658 Mechanised autoclaved fly ash lime bricks. 1000 nos 4765.79
8659 Water proof ply 12 mm thick. sqm 676.37
8660 Aluminium casement window fastener(anodised ac 15) each 41.62
8661 A'uminium casement window fastener(powder coated). each 42.66
8662 Aluminium casement window fastener (polyester powder each 41.62
coated).
8663 Aluminium round shpe handle (anodised ac" 15) each 50.99
8664 Aluminium round shpe handle (powder coated) each 56.19
8665 Aluminium round shape handle (polyester powder coated). each 61.40
8666 Stainless steei ocrews 25mmx4mm cent 33.30
8667 UV-stabilised 2 mm thick plain frp sheet. sqm 483.86
8668 UV stabilised 2 mm thick corrugated frp sheet. sqm 559.83
8669 Mangalore ridgetiles 20 mm thick each 30.18
8670 Mangalore tiles 20 mm thick. each 10.92
8671 Precoated galvanised iron rpfilesheet 0.50 mm tct sqm 452.65
8672 Precoated galvanised steel plain ridges. metre 457.84
8673 Precoated galvanised steel flashings/aprons. metre 457.84
8674 Precoated galvanised steel gutter metre 473.46
8675 Precoated galvanised steel north light curves. metre 473.46
8676 Precoated galvanised steel barge board metre 463.05
8677 Precoated galvanised steel crimp curve sqm 494.27
8678 1 mm thick 35 mm wide bright finished stainless steel paino metre 41.62
hinges.
8682 Epoxy Grout kg 530.69
8683 Red sand stone gang saw cut 30 mm thick. sqm 478.66
8684 White sand stone gang saw cut 30 mm thick. sqm 499.47
8685 Delineator each 322.57
8686 Precast c.c. kerb stone M-25 cum 4266.31
8687 Thermoplastic paint kg 65.56
8688 glass beads kg 64.52
8689 Interlocing c.c. paverblock (60 mm thick, m-30) sqm 338.18
8690 High intensity retro-reflective sheet. sqm 1586.86
8691 Punched tape concertina coil 600 m dia. 10m openable length bundle 780.42
(total length 90 m)

47 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
8692 RBT reinforced barbed wire. metre 9.36
8693 Turn buckle and strengthening bolte each set 41.62
8694 Precast pavement slab 450x450x50 mm (m-30). each 62.43
8695 Chain link fabric fencing mesh of size 50x50xmm made of G.I sqm 268.47
wire of dia. 4mm, pvc coated to outer dia. 5mm.
8696 Chain lind fabric fencing mesh of size 25x25xmm made of G.I sqm 296.56
wireof dia. 3 mm.
8697 Chain link fencing mesh of size 25x25 mm made of g.i. wire of sqm 353.80
dia. 3 mm.
8698 Stainless steei cramps with nuts, bolts and washer for dry stone each 93.65
cladding.
8699 8 mm thick tapered edge calcium silicated board. sqm 382.92
8700 10 mm thick calcium silicate board. sqm 405.82
8701 SS pipe 304 grades with press fit technology as per JIS 3448 metre 707.58
standard 48.60 mm outer dia
8702 Coupling/Socket fittings for 15.88 mm outer dia SS pipe each 59.31
8703 Telescopic drawer channels 300 mm long. set 145.68
8704 Stainless steel roller for sliding arrangement in each 8.33
racks/cupboards/cabinets shutter.
8705 50 mm x42mm x2 mm thick factory made door frame of pvc metre 145.68
extruded sections in whiter, grey or wooden finish
8706 25mm thick factory made pvc flush door shutter i/c carriage. sqm 2237.22
8707 Factory made glass reinforced plastic door frame 90x45 mm i/c metre 395.41
carriage.
8708 30 mm thick factory made glass fiber reinforced plastic panel sqm 1925.04
door shutter i/c carriage.
8709 30 mm thick factory made solid PVC profile panelled door single sqm 2757.50
piece extruded profile decorative finish (wood grain printed on
both side)
8710 Factory made solid PVC door frame 60x30xmm i/c cariage. metre 301.76
8711 28 mm factory made solid pvc panel door shutter i/c carriage. sqm 2341.27
8712 30 mm thick factory made solid PVC profile panelled door single sqm 2193.51
piece extruded profile non decorative finish
8713 Fiber glass reinforced plastic chajja. sqm 3746.03
8714 Magnetic catcher triple strip horizontal type. each 20.81
8715 Magnetic catcher double strip horizontal type. , each 15.61
8716 100 mm mortice lock with 6 levers for aluminium door. each 343.39
8717 12.5 mm thick glass fibre reinforced gypsum board. sqm 176.89
8719 2nd class teak wood lipping/moulded beading or taj beading of metre 31.21
size,18x5mm
8720 Ceilling sections 0.55 mm thick having a knurled web of 51.55 metre 41.62
mm and two flanges of 26 mm each with lips of 10.55 mm.
8721 Perimeter channel having one flange of 20 mm and metre 26.02
anotherflange of 30 mm with thickness of 0.55 mm and web of
length 27 mm.

BCD/SOR_8th Edition_October 2016 48

 Present
Code No Description Unit
Approved rate
1 2 3 4
8722 Nylon sleeves & wooden screws (40mm) each 2.08
8723 Counter sunk ribbed head screw 25 mm. cent 78.04
8724 12 mm thick marine plywood conforming to is: 710 sqm 884.48
8725 12 mm thick fire retardant plywood conforming to is:5509. sqm 915.70
8726 1.5 mm thick decorative laminated sheet sqm 509.88
8727 1.0 mm thick decorative laminated sheet sqm 395.41
8730 30 mm thick factory made glass fibre reinforced plasitc flush sqm 2237.22
door shutter i/c carriage.
8731 High polymer modified quickset tile adhesive. per kg 17.69
8732 Synthetic ployster triangular fibre of length 12 mm, effective kg 379.80
diameter 10-40 microns and specific gravity of 1:34 to 1:40
8733 Synthetic ployster triangular fibre of length 6 mm, effective kg 379.80
diameter 10-40 microns and specific gravity of 1.34 to 1.40
8734 P.V.C. Single piece extruded door frame of profile size 50 mm x metre 364.20
47 mm with wall thickness of 5 mm
8735 35 mm thick factory made solid panel PVC door shutter of single sqm 2185.18
piece extruded profile non decorative finished (Matt finished)
8736 35 mm thick factory made solid panel PVC door shutter of sqm 2705.46
singlepiece extruded profile decorative finished (Wood grain
finished)
8737 Stainless steel wire guage (Grade-304) aperture 1.4 mm and sqm 863.67
0.50 mm dia wire
8738 Factory made door frame fire rated ( 60 minutes) made with 16 metre 1040.57
SWG G.I. Sheet of section 143 mm x 57 mm duly filled with
vermuculite based concrete mix
8739 Fire rated door shuttere made with 16 SWG G.I. sheet (60 sqm 5462.96
minutes) without panel
8740 Fire seal Putty kg 728.39
8741 Clear fire resistant glass panes 6mm thick (60 minutes) sqm 21851.85
8742 G.I. U beading of 16 SWG G.I. sheet (zinc coating >120gm/m2) metre 270.55
with ceramic tape of suitable thickness and fire resistant primer
coating
8743 Matrix Mineral Board metre 67.64
8744 Panic Bar / latch (Double point) each 5202.82
8745 65 mm x 55 mm x 2 mm thick Factory made door frame of metre 343.39
PVCextruded section in white,grey or wooden finish
8746 37 mm thick Factory made shutter with style,rails and panels of sqm 2445.32
PVCextruded section in white or grey finish i/c carriage
8747 75 mm x 53 mm x 2.0 mm thick Factory made door frame of metre 364.20
PVCextruded section in white,grey or wooden finish
8748 37 mm thick Factory made fusion welded shutter with style, rails sqm 2549.38
and panels of PVC extruded section in wooden finish
8750 Zinc alloy (white powder coated) casement handle for uPVC each 166.49
windows
8751 Zinc alloy (white powder coated) Touch Lock for UPVC windows each 114.46

8752 Zinc alloy rollers for UPVC windows each 52.02

49 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
8753 Zinc alloy rollers for UPVC door each 88.45
8754 Zinc alloy (white powder coated) casement lock for UPVC each 104.06
windows
8755 Stainless steel friction hinge of size 200 mm x 19 x 1.9 mm for each 239.33
UPVC windows
8756 Stainless steel friction hinge of size 250 mm x 19 x 1.9 mm for each 301.76
UPVC windows
8757 Stainless steel friction hinge of size3000 mm x 19 x 1.9 mm for each 385.01
UPVC windows
8758 Stainless steel friction hinge of size350mm x 19 x 1.9 mm for each 437.03
UPVC windows
8759 Stainless steel friction hinge of size 400 mm x 19 x 1.9 mm for each 551.50
UPVC windows
8760 UPVC extruded profile casement window Frame (50 mm x 50 metre 171.70
mm)
8761 UPVC extruded profile casement window sash (Style and Rail) metre 156.08
(62 mm x34 mm)
8762 UPVC extruded profile casement window mullion (intermediate metre 192.50
section)(66 mm x 50 mm)
8763 UPVC extruded profile casement window 'T' profile (one vertical metre 52.02
lengthin between two shutters) (24 mm x 34.5 mm)
8764 UPVC extruded profile casement window glazing bead (12 mm x metre 52.02
18mm)
8765 UPVC extruded profile casement window Frame ( 67 mm x 62 metre 244.53
mm)
8766 UPVC extruded profile casement Window Sash/Mullion ( 67 mm metre 275.75
x 75mm) (Style,rail and intermediate section)
8767 UPVC extruded profile casement window glazing bead (35 mm x metre 88.45
18mm)
8768 UPVC extruded profile Two Track Sliding frame (67 mm x 52 metre 254.93
mm)
8769 UPVC extruded profile Sliding window Sash (60 mm x 44 mm) metre 239.33
8770 UPVC extruded profile Sliding Interlock for Window (one vertical metre 52.02
lengthin each shutter) (45.5 mm x 28 mm)
8771 UPVC extruded profile Sliding Door Sash (80 mm x 44 mm) metre 301.76
8772 Aluminium Track on bottom rail for uPVC window metre 26.02
8773 Wool Pine for uPVC window metre 18.73
8774 Aluminium Grill metre 260.14
8775 Steel Galvanised tubular reinforcement for uPVC door/ window metre 52.02
8776 Stainless steel dash fastener of 8 mm dia and 75 mm long bolt each 20.81
8778 Toughened glass 12 mm thickness sqm 1977.07
8779 SS pipe 304 grades with press fit technology as per JIS 3448 metre 149.84
standard 15.88 mm outer dia
8780 SS pipe 304 grades with press fit technology as per JIS 3448 metre 264.31
standard 22.22 mm outer dia

BCD/SOR_8th Edition_October 2016 50

 Present
Code No Description Unit
Approved rate
1 2 3 4
8781 SS pipe 304 grades with press fit technology as per JIS 3448 metre 343.39
standard 28.58 mm outer dia
8782 SS pipe 304 grades with press fit technology as per JIS 3448 metre 486.98
standard 34.00 mm outer dia
8783 SS pipe 304 grades with press fit technology as per JIS 3448 metre 605.61
standard 42.70 mm outer dia
8784 8 mm thick Calcium silicate perforated tiles of size 595 x595 mm sqm 715.91
8786 Coupling/Socket fittings for 22.22 mm outer dia SS pipe each 91.57
8787 Coupling/Socket fittings for 28.58 mm outer dia SS pipe each 112.38
8788 Coupling/Socket fittings for 34.00 mm outer dia SS pipe each 240.37
8789 Coupling/Socket fittings for 42.70 mm outer dia SS pipe each 343.39
8790 Coupling/Socket fittings for 48.60 mm outer dia SS pipe each 464.09
8791 Reducer for 22.22 mm X 15.88 mm outer Dia SS pipe each 107.18
8792 Reducer for 28.58 mm X 15.88 mm outer Dia SS pipe each 146.72
8793 Reducer for 28.58 mm X 22.22 mm outer Dia SS pipe each 150.89
8794 Reducer for 34.00 mm X 15.88 mm outer Dia SS pipe each 226.82
8795 Reducer for 34.00 mm X 22.22 mm outer Dia SS pipe each 246.62
8796 Reducer for 34.00 mm X 28.58 mm outer Dia SS pipe each 246.62
8797 Reducer for 42.70 mm X 15.88 mm outer Dia SS pipe each 373.56
8798 Reducer for 42.70 mm X 22.22 mm outer Dia SS pipe each 376.68
8799 Reducer for 42.70 mm X 28.58 mm outer Dia SS pipe each 376.68
8800 Reducer for 42.70 mm X 34.00 mm outer Dia SS pipe each 402.70
8801 Reducer for 48.60 mm X 15.88 mm outer Dia SS pipe each 486.98
8802 Reducer for 48.60 mm X 22.22 mm outer Dia SS pipe each 489.07
8803 Reducer for 48.60 mm X 28.58 mm outer Dia SS pipe each 493.23
8804 Reducer for 48.60 mm X 34.00 mm outer Dia SS pipe each 498.43
8805 Reducer for48.60 mm X 42.70 mm outer Dia SS pipe each 543.17
8806 Slip Coupling / Socket 15.88 mm outer dia SS pipe each 117.58
8807 Slip Coupling / Socket 22.22 mm outer dia SS pipe each 191.46
8808 Slip Coupling / Socket 28.58 mm outer dia SS pipe each 245.57
8809 Slip Coupling / Socket 34.00 mm outer dia SS pipe each 363.16
8810 Slip Coupling / Socket 42.70 mm outer dia SS pipe each 509.88
8811 Slip Coupling / Socket 48.60 mm outer dia SS pipe each 633.70
8812 Elbow 90o for 15.88 mm outer dia SS pipe each 89.49
8813 Elbow 90o for 22.22 mm outer dia SS pipe each 159.20
8814 Elbow 90o for 28.58 mm outer dia SS pipe each 219.56
8815 Elbow 90o for 34.00 mm outer dia SS pipe each 446.41
8816 Elbow 90o for 42.70 mm outer dia SS pipe each 683.65
8817 Elbow 90o for 48.60 mm outer dia SS pipe each 840.78
8818 Reducing Elbow 90o for 22.22 mm X 15.88 mm outer dia SS each 154.01
pipe

51 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
8819 Reducing Elbow 90o for 28.58 mm X 15.88 mm outer dia SS each 224.76
pipe
8820 Reducing Elbow 90o for 28.58 mm X 22.22 mm outer dia SS each 229.96
pipe
8821 Reducing Elbow 90o for 34.00 mm X 22.22 mm outer dia SS each 334.02
pipe
8822 Reducing Elbow 90o for 34.00 mm X 28.58 mm outer dia SS each 412.06
pipe
8823 Reducing Elbow 90o for 42.70 mm X 34.00 mm outer dia SS each 726.31
pipe
8824 Equal Tee for 15.88 mm outer dia SS pipe each 165.45
8825 Equal Tee for 22.22 mm outer dia SS pipe each 240.37
8826 Equal Tee for 28.58 mm outer dia SS pipe each 308.01
8827 Equal Tee for 34.00 mm outer dia SS pipe each 642.03
8828 Equal Tee for 42.70 mm outer dia SS pipe each 899.05
8829 Equal Tee for 48.60 mm outer dia SS pipe each 1069.70
8830 Reducing Tee for 22.22 mm X 15.88 mm outer dia SS pipe each 234.12
8831 Reducing Tee for 28.58 mm X 15.88 mm outer dia SS pipe each 291.36
8832 Reducing Tee for 28.58 mm X 22.22 mm outer dia SS pipe each 302.80
8833 Reducing Tee for 34.00 mm X 15.88 mm outer dia SS pipe each 570.23
8834 Reducing Tee for 34.00 mm X 22.22 mm outer dia SS pipe each 580.64
8835 Reducing Tee for 34.00 mm X 28.58 mm outer dia SS pipe each 586.88
8836 Reducing Tee for 42.70 mm X 15.88 mm outer dia SS pipe each 852.23
8837 Reducing Tee for 42.70 mm X 22.22 mm outer dia SS pipe each 854.30
8838 Reducing Tee for 42.70 mm X 28.58 mm outer dia SS pipe each 855.35
8839 Reducing Tee for 42.70 mm X 34.00 mm outer dia SS pipe each 863.67
8840 Reducing Tee for 48.60 mm X 15.88 mm outer dia SS pipe each 930.27
8841 Reducing Tee for 48.60 mm X 22.22 mm outer dia SS pipe each 950.03
8842 Reducing Tee for 48.60 mm X 28.58 mm outer dia SS pipe each 957.32
8843 Reducing Tee for 48.60mm X 34.00 mm outer dia SS pipe each 996.86
8844 Reducing Tee for 48.60mm X 42.70mm outer dia SS pipe each 1033.28
8845 Male thread Tee for 15.88 mm outer dia X 15 mm nominal dia each 297.60
threaded
8846 Male thread Tee for 22.22 mm outer dia X 15 mm nominal dia each 357.95
threaded
8847 Male thread Tee for 22.22 mm outer dia X 20 mm nominal dia each 382.92
threaded
8848 Male thread Tee for 28.58 mm outer dia X 15 mm nominal dia each 430.79
threaded
8849 Male thread Tee for 28.58 mm outer dia X 20 mm nominal dia each 449.53
threaded
8850 Male thread Tee for 28.58 mm outer dia X 20 mm nominal dia each 502.59
threaded
8851 Male thread Tee for 34.00 mm outer dia X 15 mm nominal dia each 626.42

BCD/SOR_8th Edition_October 2016 52

 Present
Code No Description Unit
Approved rate
1 2 3 4
8852 Male thread Tee for 34.00 mm outer dia X 20 mm nominal dia each 677.41
threaded
8853 Male thread Tee for 34.00 mm outer dia X 25 mm nominal dia each 808.52
threaded
8854 Male thread Tee for 34.00 mm outer dia X 32 mm nominal dia each 1020.79
threaded
8855 Male thread Tee for 42.70 mm outer dia X 15 mm nominal dia each 956.27
threaded
8856 Male thread Tee for 42.70 mm outer dia X 20 mm nominal dia each 979.17
threaded
8857 Male thread Tee for 42.70 mm outer dia X 25 mm nominal dia each 1065.54
threaded
8858 Male thread Tee for 42.70 mm outer dia X 32 mm nominal dia each 1183.12
threaded
8859 Male thread Tee for 42.70 mm outer dia X 40 mm nominal dia each 1437.02
threaded
8860 Male thread Tee for 48.60 mm outer dia X 15 mm nominal dia each 1040.57
threaded
8861 Male thread Tee for 48.60 mm outer dia X 20 mm nominal dia each 1071.78
threaded
8862 Male thread Tee for 48.60 mm outer dia X 25 mm nominal dia each 1117.56
threaded
8863 Male thread Tee for 48.60 mm outer dia X 32 mm nominal dia each 1342.33
threaded
8864 Male thread Tee for 48.60 mm outer dia X 40 mm nominal dia each 1489.05
threaded
8865 Male thread Tee for 48.60 mm outer dia X 50 mm nominal dia each 1819.95
threaded
8866 Female thread Tee for 15.88 mm outer dia X 15 mm nominal dia each 303.85
threaded
8867 Female thread Tee for 22.22 mm outer dia X 15 mm nominal dia each 357.95

8868 Female thread Tee for 22.22 mm outer dia X 20 mm nominal dia each 370.44
threaded
8869 Female thread Tee for 28.58 mm outer dia X 15 mm nominal dia each 463.05
threaded
8870 Female thread Tee for 28.58 mm outer dia X 20 mm nominal dia each 473.46
threaded
8871 Female thread Tee for 28.58 mm outer dia X 25 mm nominal dia each 518.20
threaded
8872 Female thread Tee for 34.00 mm outer dia X 15 mm nominal dia each 695.10
threaded
8873 Female thread Tee for 34.00 mm outer dia X 20 mm nominal dia each 706.55
threaded
8874 Female thread Tee for 34.00 mm outer dia X 25 mm nominal dia each 797.07
threaded
8875 Female thread Tee for 34.00 mm outer dia X 32 mm nominal dia each 946.91
threaded

53 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
8876 Female thread Tee for 42.70 mm outer dia X 15 mm nominal dia each 930.27
threaded
8877 Female thread Tee for 42.70 mm outer dia X 20 mm nominal dia each 946.91
threaded
8878 Female thread Tee for 42.70 mm outer dia X 25 mm nominal dia each 1063.45
threaded
8879 Female thread Tee for 42.70 mm outer dia X 32 mm nominal dia each 1110.28
threaded
8880 Female thread Tee for 42.70 mm outer dia X 40 mm nominal dia each 1209.13
threaded
8881 Female thread Tee for 48.60 mm outer dia X 15 mm nominal dia each 1108.20
threaded
8882 Female thread Tee for 48.60 mm outer dia X 20 mm nominal dia each 1119.65
threaded
8883 Female thread Tee for 48.60 mm outer dia X 25 mm nominal dia each 1160.23
threaded
8884 Female thread Tee for 48.60 mm outer dia X 32 mm nominal dia each 1232.03
threaded
8885 Female thread Tee for 48.60 mm outer dia X 40 mm nominal dia each 1283.02
threaded
8886 Female thread Tee for 48.60 mm outer dia X 50 mm nominal dia each 1421.41
threaded
8887 Female threaded Connector/Adapter for 15.88 mm outer dia X each 197.70
15mm nominal threaded
8888 Female threaded Connector/Adapter for 22.22 mm outer dia X each 239.33
15mm nominal threaded
8889 Female threaded Connector/Adapter for 22.22 mm outer dia X each 246.62
20mm nominal threaded
8890 Female threaded Connector/Adapter for 28.58 mm outer dia X each 288.24
15mm nominal threaded
8891 Female threaded Connector/Adapter for 28.58 mm outer dia X each 297.60
20mm nominal threaded
8892 Female threaded Connector/Adapter for 28.58 mm outer dia X each 350.67
25mm nominal threaded
8893 Female threaded Connector/Adapter for 34.00 mm outer dia X each 425.59
25mm nominal threaded
8894 Female threaded Connector/Adapter for 34.00 mm outer dia X each 559.83
32mm nominal threaded
8895 Female threaded Connector/Adapter for 42.70 mm outer dia X each 599.37
32mm nominal threaded
8896 Female threaded Connector/Adapter for 42.70 mm outer dia X each 708.62
40mm nominal threaded
8897 Female threaded Connector/Adapter for 48.60 mm outer dia X each 871.99
40mm nominal threaded
8898 Female threaded Connector/Adapter for 48.60 mm outer dia X each 1004.14
50mm nominal threaded
8899 Male threaded Connector/Adapter for 15.88 mm outer dia X each 200.83
15mm nominal threaded

BCD/SOR_8th Edition_October 2016 54 1

 Present
Code No Description Unit
Approved rate
1 2 3 4
8900 Male threaded Connector/Adapter for 22.22 mm outer dia X each 236.21
15mm nominal threaded
8901 Male threaded Connector/Adapter for 22.22 mm outer dia X each 258.06
20mm nominal threaded
8902 Male threaded Connector/Adapter for 28.58 mm outer dia X each 325.70
20mm nominal threaded
8903 Male threaded Connector/Adapter for 28.58 mm outer dia X each 332.98
25mm nominal threaded
8904 Male threaded Connector/Adapter for 34.00 mm outer dia X each 479.70
25nominal dia threaded
8905 Male threaded Connector/Adapter for 34.00 mm outer dia X each 587.92
32nominal dia threaded
8906 Male threaded Connector/Adapter for 42.70 mm outer dia X each 675.32
32nominal dia threaded
8907 Male threaded Connector/Adapter for 42.70 mm outer dia X 40 each 755.45
nominal dia threaded
8908 Male threaded Connector/Adapter for 48.60 mm outer dia X 40 each 874.08
8909 Male threaded Connector/Adapter for 48.60 mm outer dia X 50 each 1184.16
nominal dia threaded
8910 Valve Connector for 15.88 mm outer dia X 15 mm nominal dia each 243.50
nominal dia threaded
8911 Valve Connector for 22.22 mm outer dia X 15 mm nominal dia each 287.19
nominal dia threaded
8912 Valve Connector for 22.22 mm outer dia X 20 mm nominal dia each 306.97
nominal dia threaded
8913 Valve Connector for 28.58 mm outer dia X 25 mm nominal dia each 441.20
nominal dia threaded
8914 Valve Connector for 34.00 mm outer dia X 32 mm nominal dia each 654.51
nominal dia threaded
8915 Valve Connector for 42.70 mm outer dia X 40 mm nominal dia each 910.49
nominal dia threaded
8916 Valve Connector for 48.60 mm outer dia X 50 mm nominal dia each 1223.70
nominal dia threaded
8917 Female Threaded Elbow 90o for 15.88 mm outer dia X 15 mm each 213.31
nominal dia threaded
8918 Female Threaded Elbow 90o for 22.22 mm outer dia X 15 mm each 286.16
nominal dia threaded
8919 Female Threaded Elbow 90o for 22.22 mm outer dia X 20 mm each 295.52
nominal dia threaded
8920 Female Threaded Elbow 90o for 28.58 mm outer dia X 25 mm each 438.08
nominal dia threaded
8921 Female Threaded Elbow 90o for 34.00 mm outer dia X 32 mm each 762.74
nominal dia threaded
8922 Female Threaded Elbow 90o for 42.70 mm outer dia X 32 mm each 957.32
nominal dia threaded
8923 Female Threaded Elbow 90o for 42.70 mm outer dia X40 mm each 1035.36
nominal dia threaded

1 55 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
8924 Female Threaded Elbow 90o for 48.60 mm outer dia X 40 mm each 1147.75
nominal dia threaded
8925 Female Threaded Elbow 90o for 48.60 mm outer dia X 50 mm each 1338.16
nominal dia threaded
8926 Male Threaded Elbow 90o for 15.88 mm outer dia X 15 mm each 224.76
nominal dia threaded
8927 Male Threaded Elbow 90o for 22.22 mm outer dia X 15 mm each 284.07
nominal dia threaded
8928 Male Threaded Elbow 90o for 22.22 mm outer dia X 20 mm each 299.68
nominal dia threaded
8929 Male Threaded Elbow 90o for 28.58 mm outer dia X 25 mm each 392.29
nominal dia threaded
8930 MaleThreaded Elbow 90o for 34.00 mm outer dia X 25 mm each 629.54
nominal dia threaded
8931 Male Threaded Elbow 90o for 34.00 mm outer dia X 32 mm each 765.86
nominal dia threaded
8932 Male Threaded Elbow 90o for 42.70 mm outer dia X 32 mm each 971.89
nominal dia threaded
8933 Male Threaded Elbow 90o for 42.70 mm outer dia X40 mm each 1103.00
nominal dia threaded
8934 Male Threaded Elbow 90o for 48.60 mm outer dia X 40 mm each 1238.27
nominal dia threaded
8935 Male Threaded Elbow 90o for 48.60 mm outer dia X 50 mm each 1507.78
nominal
8936 Cap for 15.88 mm outer dia pipe each 46.83
8937 Cap for 22.22 mm outer dia pipe each 66.59
8938 Cap for 28.58 mm outer dia pipe each 87.40
8939 Cap for 34.00 mm outer dia pipe each 180.01
8940 Cap for 42.70 mm outer dia pipe each 263.26
8941 Cap for 48.60 mm outer dia pipe each 343.39
8942 Pipe Bridge for 15.88 mm outer dia pipe each 222.68
8943 Pipe Bridge for 15.88 mm outer dia pipe each 281.99
8944 Pipe Bridge for 28.58 mm outer dia pipe each 423.51
8945 4 Point facade glass bracket Nos 3452.60
8946 2 Point facade glass bracket Nos 1726.29
8947 1 Point facade glass bracket Nos 1460.95
8948 Flate head bolt Nos 677.41
8949 400 fin plate at top pair 6171.59
8953 Micro Silica kg 33.30
8954 Stop end tubes for diaphragmwall 600 mm dia. sqm 4.68
8955 Driving end tubes for diaphragm wall 600 mm dia. sqm 74.92
9999 Sundries L.S. 1.76
0842 Ready mix paint for wood work Per litre 211.77
0843 Ready mix paint for steel work Per litre 211.77
0288 Brick Khoa Per m3 1523.55
1002 Mild steel round bar 12mm dia and below quintal 3606.75
1007 Structural steel quintal 3711.75
0993 Plain A.C sheet standard quality(6mm thick) sqm 190.51

BCD/SOR_8th Edition_October 2016 56 1

 NEW CODES
Present
Code No Description Unit
Approved rate
1 2 3 4
0303 Cowdung cum 49.95
0801 Silicon and acrylic emulsion litre 208.12
0802 Acrylic distemper 1st quality , having VOC content less than Kg 39.54
50gm/litre
0803 Acrylic emulsion , having VOC content less than 50 gm/litre litre 260.14
0804 Premium acrylic emulsion of interior grade, having VOC content litre 364.20
less than 50 gm/litre
0805 Synthetic enamel paint , having VOC (Volatile Organic litre 228.93
Compound) content less than 150 gm/litre
0806 Ready mixed pink or grey primer on wood work (hard and soft litre 124.87
wood) having VOC content less than 50 gms/litre
0807 Ready mixed red oxide zinc chromatic on steel/ iron work, having litre 135.27
VOC content less than 250 gms/litre
0808 Water thinnable cement primer for interior wall surface, having litre 62.43
VOC content less than 50 gms/litre
0809 Exterior Primer kg 41.62
0824 Cement base wall care putty kg 24.97
1011 Steel glazed door,window/ ventilator, all members viz. F7D, kg 49.95
F4B,K11 and K12B etc
1200 Kiln seasoned selected sheesham wood planks 10 cudm 676.37
1204 Precast heat resistant terrace tiles (size 300x300 mm) and 20 sqm 501.55
mm thick
2393 1 mm thick Stainless Steel Cover plate grade 304 kg 286.16
2394 Coupler 16 mm dia sqm 69.71
2395 Coupler 20 mm dia sqm 91.57
2396 Coupler 25 mm dia sqm 135.27
2397 Coupler 28 mm dia sqm 199.79
2398 Coupler 32 mm dia sqm 240.37
2408 Float glass sheet of nominal thickness 8 mm (weight not less sqm 728.39
than20.00 kg/ sqm)
2413 12 mm commercial ply sqm 603.53
2414 18 mm thick block board with commercial ply veneering on both sqm 728.39
side
2506 Carben Steel galvanised dash fastner (min 5 micron) of 10 mm 10nos 260.14
diadouble threaded 6.8 grade counter sunk head screw
comprising of 10 mmdia polyamide PA 6 grade sleave. Size 10
mm x 60 mm
2507 Carben Steel galvanised dash fastner (min 5 micron) of 10 mm 10nos 304.88
diadouble threaded 6.8 grade counter sunk head screw
comprising of 10 mmdia polyamide PA 6 grade sleave. Size 10
mm x 80 mm

1 57 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
2508 Carben Steel galvanised dash fastner (min 5 micron) of 10 mm 10nos 378.77
diadouble threaded 6.8 grade counter sunk head screw
comprising of 10 mmdia polyamide PA 6 grade sleave. Size 10
mm x120 mm
2509 Carben Steel galvanised dash fastner (min 5 micron) of 10 mm 10nos 468.26
diadouble threaded 6.8 grade counter sunk head screw
comprising of 10 mmdia polyamide PA 6 grade sleave. Size 10
mm x140 mm
2510 Carben Steel galvanised dash fastner (min 5 micron) of 10 mm 10nos 593.12
diadouble threaded 6.8 grade counter sunk head screw
comprising of 10 mmdia polyamide PA 6 grade sleave. Size 10
mm x160 mm
2708 Truf Paver (500 x 500 x 40 mm) sqm 1134.22
2709 Ceremic Tiles Pieces for Crazy Flooring quintal 140.48
3327 15 mm Battery Based Sensor Pillar Cock each 6058.17
4001 Stainless steel (Grade-304)hollow section round/square tubes kg 364.20
4002 Stainless steel bolts/square bar and plates kg 135.27
7007 Fly Ash Bricks as per IS 12894(2002) & IS 3425(I to IV) per 1000 5975.55
7028 12.5 mm thick Fully Perforated gypsum board sqm 964.60
7030 12.5 mm thick tapered edge gypsum fire resistant board sqm 246.62
7031 12.5 mm thick tapered edge gypsum moisture resistant board sqm 281.99
7050 PU Primer sqm 42.66
7051 40 mm (average) PU spray having 40-45 kg/m3 density sqm 438.08
7052 GI wire netting 3/4" x 24 G sqm 28.09
7053 400 G polythene sheet sqm 15.61
7072 Wall mounted water closet each 4838.62
7073 Adjustable Vetrious China Cistern with fittings each 2601.42
7074 White Vetrious China Waterless Urinal each 15608.46
7075 Cistern with fittings for Waterless Urinal each 3537.92
7076 White Vetrious Urinal each 14567.90
7178 Chemical ASTMC-type I kg 114.46
7280 Waste plastic additive tonne 41622.58
7281 Chemical ASTMC-type II kg 176.89
7743 M.S. pipe 150 mm dia casing pipe metre 1103.00
7744 M.S. pipe 200 mm dia casing pipe metre 1352.73
7745 PVC blind pipe 150 mm dia as per IS: 12818 metre 520.28
7746 PVC blind pipe 200 mm dia as per IS: 12818 metre 7804.24
7747 M.S. cap 150 mm dia each 166.49
7748 M.S. cap 200 mm dia each 208.12
7749 M.S bail plug 150 mm dia each 208.12
7750 M.S bail plug 200 mm dia each 228.93
7751 PVC slotted pipe 150 mm dia as per IS: 12818 metre 468.26

BCD/SOR_8th Edition_October 2016 58 1

 Present
Code No Description Unit
Approved rate
1 2 3 4
7752 PVC slotted pipe 200 mm dia as per IS: 12818 metre 728.39
7753 Boulder 50 mm to 200 mm cum 364.20
7754 Gravel 5 mm to 10 mm cum 728.39
7755 Gravel 1.5 mm to 2 mm cum 676.37
7756 Gravel 3 mm to 6 mm cum 707.58
7757 M.S. pipe 100 mm dia casing pipe metre 801.23
7758 UPVC blind pipe 100 mm dia as per IS: 12818 metre 374.61
7759 UPVC slotted pipe 100 mm dia as per IS: 12818 metre 395.41
7760 M.S. cap 100 mm dia each 135.27
7761 M.S. bail plug 100 mm dia each 166.49
7762 Precast R.C.C. perforated slab each 832.45
7763 Water supply tanker of 5000 litre capacity each 832.45
7764 M.S. socket 100 mm dia each 187.30
7765 M.S. socket 150 mm dia each 228.93
7766 M.S. socket 200 mm dia each 291.36
7767 Stone cleaning chemical approved by ASI litre 171.70
7768 Water repallent chemical approved by ASI litre 1651.37
7769 Stone surface strengthening chemical approved by ASI litre 1061.38
7770 Turpentine oil litre 70.76
7771 Liquid Amonia 5% litre 167.53
7772 Pea Gravel cum 780.42
8014 Factory made door frame of size 50x47 mm with wall thickness 5 metre 509.88
mm made of single piece extruded profile
8589 Calcium Silicate tegular edged celling tiles 595x595 mm and 15 sqm 892.80
mm thick
8590 Galvanised Steel main Tee ceiling section Size 24 x 38 x 0.33 each 199.79
mm(3 metre long)
8591 Galvanised Steel perimeter wall Angle Size 24 x 24 x 0.40 mm each 130.07
(3.00metre long)
8592 Galvanised Steel intermediate cross T section Size 24 x 25 x each 80.12
0.33 mm(1.2 metre long)
8593 Galvanised Steel intermediate cross T section Size 24 x 25 x each 40.59
0.33 mm ( 0.6 metre long)
8594 Galvanised Steel soffit cleat size 25x35x1.60 mm each 3.12
8595 Wooden screws with plastic rawl plugs 35x8 mm each 0.62
8597 GI Metal Tile Clip in Plain Beveled edge global white colour tiles sqm 931.30
of size 600x600 mm and 0.5 mm thick
8598 GI Metal Tile Clip in Perforated Beveled edge global white colour sqm 1040.57
tiles of size 600x600 mm and 0.5 mm thick
8599 GI Metal Tile Lay-in Plain Tegular edge global white color tiles of sqm 841.82
Size595x595 mm and 0.5 mm thick

1 59 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
8600 GI Metal Tile Lay-in Perforated Tegular edge global white color sqm 942.75
tiles ofSize 595x595 mm and 0.5 mm thick
8601 PVC Laminated Gypsum Tiles (Square edge) of Size 595x595 sqm 486.98
mm and 12.5 mm thick
8602 Gypsum Tiles Fully Perforated Square edge of Size 595x595 sqm 503.64
mm and 12.5 mm thick
8604 Spring T-section 24x34x0.45 mm (3.00 meter long) metre 187.30
8605 C Wall angle section 20x30x20x0.50 mm (3.00 meter long) metre 161.29
8606 Main C Carrier Size 10x38x10x0.70 mm (3.00 meter long) metre 170.65
8607 Spring T-connector each 5.21
8608 C Carrier Connector each 11.45
8609 C Suspension Clip each 11.45
8610 Wire Coupling Clip each 9.36
8682 Epoxy Grout kg 530.69
8709 30 mm thick factory made solid PVC profile panelled door single sqm 2757.50
piece extruded profile decorative finish (wood grain printed on
both side)
8712 30 mm thick factory made solid PVC profile panelled door single sqm 2193.51
piece extruded profile non decorative finish
8734 P.V.C. Single piece extruded door frame of profile size 50 mm x metre 364.20
47 mm with wall thickness of 5 mm
8735 35 mm thick factory made solid panel PVC door shutter of single sqm 2185.18
piece extruded profile non decorative finished (Matt finished)

8736 35 mm thick factory made solid panel PVC door shutter of sqm 2705.46
singlepiece extruded profile decorative finished (Wood grain
finished)
8737 Stainless steel wire guage (Grade-304) aperture 1.4 mm and sqm 863.67
0.50 mm dia wire
8738 Factory made door frame fire rated ( 60 minutes) made with 16 metre 1040.57
SWG G.I. Sheet of section 143 mm x 57 mm duly filled with
vermuculite based concrete mix
8739 Fire rated door shuttere made with 16 SWG G.I. sheet (60 sqm 5462.96
minutes) without panel
8740 Fire seal Putty kg 728.39
8741 Clear fire resistant glass panes 6mm thick (60 minutes) sqm 21851.85
8742 G.I. U beading of 16 SWG G.I. sheet (zinc coating >120gm/m2) metre 270.55
with ceramic tape of suitable thickness and fire resistant primer
coating
8743 Matrix Mineral Board metre 67.64
8744 Panic Bar / latch (Double point) each 5202.82
8745 65 mm x 55 mm x 2 mm thick Factory made door frame of metre 343.39
PVCextruded section in white,grey or wooden finish
8746 37 mm thick Factory made shutter with style,rails and panels of sqm 2445.32
PVCextruded section in white or grey finish i/c carriage
8747 75 mm x 53 mm x 2.0 mm thick Factory made door frame of metre 364.20
PVCextruded section in white,grey or wooden finish

BCD/SOR_8th Edition_October 2016 60

 Present
Code No Description Unit
Approved rate
1 2 3 4
8748 37 mm thick Factory made fusion welded shutter with style, rails sqm 2549.38
and panels of PVC extruded section in wooden finish
8750 Zinc alloy (white powder coated) casement handle for uPVC each 166.49
windows
8751 Zinc alloy (white powder coated) Touch Lock for UPVC windows each 114.46

8752 Zinc alloy rollers for UPVC windows each 52.02

8753 Zinc alloy rollers for UPVC door each 88.45
8754 Zinc alloy (white powder coated) casement lock for UPVC each 104.06
windows
8755 Stainless steel friction hinge of size 200 mm x 19 x 1.9 mm for each 239.33
UPVC windows
8756 Stainless steel friction hinge of size 250 mm x 19 x 1.9 mm for each 301.76
UPVC windows
8757 Stainless steel friction hinge of size3000 mm x 19 x 1.9 mm for each 385.01
UPVC windows
8758 Stainless steel friction hinge of size350mm x 19 x 1.9 mm for each 437.03
UPVC windows
8759 Stainless steel friction hinge of size 400 mm x 19 x 1.9 mm for each 551.50
UPVC windows
8760 UPVC extruded profile casement window Frame (50 mm x 50 metre 171.70
mm)
8761 UPVC extruded profile casement window sash (Style and Rail) metre 156.08
(62 mm x34 mm)
8762 UPVC extruded profile casement window mullion (intermediate metre 192.50
section)(66 mm x 50 mm)
8763 UPVC extruded profile casement window 'T' profile (one vertical metre 52.02
lengthin between two shutters) (24 mm x 34.5 mm)
8764 UPVC extruded profile casement window glazing bead (12 mm x metre 52.02
18mm)
8765 UPVC extruded profile casement window Frame ( 67 mm x 62 metre 244.53
mm)
8766 UPVC extruded profile casement Window Sash/Mullion ( 67 mm metre 275.75
x 75mm) (Style,rail and intermediate section)
8767 UPVC extruded profile casement window glazing bead (35 mm x metre 88.45
18mm)
8768 UPVC extruded profile Two Track Sliding frame (67 mm x 52 metre 254.93
mm)
8769 UPVC extruded profile Sliding window Sash (60 mm x 44 mm) metre 239.33

8770 UPVC extruded profile Sliding Interlock for Window (one vertical metre 52.02
lengthin each shutter) (45.5 mm x 28 mm)
8771 UPVC extruded profile Sliding Door Sash (80 mm x 44 mm) metre 301.76
8772 Aluminium Track on bottom rail for uPVC window metre 26.02
8773 Wool Pine for uPVC window metre 18.73
8774 Aluminium Grill metre 260.14

61 BCD/SOR_8th Edition_October 2016

 Present
Code No Description Unit
Approved rate
1 2 3 4
8775 Steel Galvanised tubular reinforcement for uPVC door/ window metre 52.02
8776 Stainless steel dash fastener of 8 mm dia and 75 mm long bolt each 20.81
8778 Toughened glass 12 mm thickness sqm 1977.07
8779 Paver Block
A M35 grade 60mm thick
White sqm 480.12
Red sqm 488.73
Yellow sqm 504.09
B M40 grade 80mm thick
White sqm 551.04
Red sqm 565.43
Yellow sqm 583.63
8780 Kerb Stone Block M30 Grade of Size 375mm x 300mm each 80.63

Note:-
* Rate based on DSR 2013
** Approved rate by State level Schedule rate committee with Vat 5.0%
*** Approved rate of cement by State level schedule rate committee with vat 13.5%

lnL; lnL;] lnL;]

jkT;Lrjh; vuqlwfpr nj fu/kkZj.k jkT;Lrjh; vuqlwfpr nj fu/kkZj.k jkT;Lrjh; vuqlwfpr nj fu/kkZj.k
lfefr&lg&vfHk;ark izeq[k&lg& lfefr&lg&vfHk;ark izeq[k ¼eè;½] lfefr&lg&vfHk;ark izeq[k]
vij vk;qDr&lg&fo’ks"k lfpo] ty lalk/ku foHkkx] fcgkj] iVukA y?kq ty lalk/ku foHkkx] fcgkj] iVukA
Hkou fuekZ.k foHkkx] fcgkj] iVukA

lnL;] lnL;] lnL;]

jkT;Lrjh; vuqlwfpr nj fu/kkZj.k jkT;Lrjh; vuqlwfpr nj fu/kkZj.k jkT;Lrjh; vuqlwfpr nj fu/kkZj.k
lfefr&lg&eq[; vfHk;ark ¼vlS0½] lfefr&lg&eq[; vfHk;ark ¼fo|qr½] lfefr&lg&vfHk;ark izeq[k] rduhdh ijh{k.k
fcgkj LVsV ikoj gksfYMax daiuh fyfeVsM] Hkou fuekZ.k foHkkx] fcgkj] iVukA dks"kkax] fuxjkuh foHkkx] fcgkj] iVukA
fcgkj] iVukA

lnL;] lnL;] lnL;]

jkT;Lrjh; vuqlwfpr nj fu/kkZj.k jkT;Lrjh; vuqlwfpr nj fu/kkZj.k jkT;Lrjh; vuqlwfpr nj fu/kkZj.k
lfefr&lg&vfHk;ark izeq[k] lfefr&lg&vfHk;ark izeq[k] lfefr&lg&vfHk;ark izeq[k&lg&
yksd LokLF; vfHk;a=.k foHkkx] xzkeh.k dk;Z foHkkx] fcgkj] iVukA vij vk;qDr&lg&fo’ks"k lfpo]
fcgkj] iVukA iFk fuekZ.k foHkkx] fcgkj] iVukA

BCD/SOR_8th Edition_October 2016 62

 SUB HEAD : 0.4
CAPACITY OF TRUCK
 TRUCK CAPACITY PER TRIP
VIDE T.E.C. LETTER No 1115 DATED 12.07.85

Net payable Volume

S. No Materials Truck Capacity
or weight col 3*col 4
1 2 3 4 5
1 line,Moorum and building rubbish 6.00cum 1.00 6.00 cum
2 Earth 6.00cum 0.80 4.80 cum
3 Manure or sludge 6.00cum 0.92 5.52 cum
4 Excavated rocks(120 Lbs) 6.00cum 0.67 4.02 cum
5 Stone Metal 5.40cum 0.85 4.59 cum
6 Soling stone 5.00cum 0.85 4.25 cum
7 Boulder(90 Lbs to 120 Lbs) 6.00cum 0.8 4.80 cum
8 Bricks 2000Nos 1.00 2000 Nos
9 Tiles/Mangra/Mosaic 3200Nos 1.00 3200Nos
10 Bricks tiles(300*150*50mm) 1760Nos 1.00 1760 Nos
Cement,Stone blocks ,G.I .C.I .A.C and 8.00Mt 1.00 8.00MT
11 C.C Pipe below 100 mm dia and other
heavy materials
12 Steel 8.00Mt 1.00 8.00MT
13 Timber 9.60 cum 1.00 9.60 cum
14 Tar,Bitumen 8.00M.T 1.00 8.00MT
15 steam coal 8.00 MT 1.00 8.00MT
16 S.W.pipe 60 cm,length
(i) 100 mm dia 800No / 480M 1.00 800No / 480M
(ii) 150 mm dia 400 No / 240 M 1.00 400 No / 240 M
(iii) 200 mm dia 224 No / 134.40 M 1.00 224 No / 134.40 M
(iv) 230 mm dia 176 No / 105.60 M 1.00 176 No / 105.60 M
(v) 250 mm dia 140 No / 84 M 1.00 140 No / 84 M
(vi) 300 mm dia 112 No / 67.20 M 1.00 112 No / 67.20 M
(vii) 350 mm dia 80 No / 48 M 1.00 80 No / 48.20 M
(viii) 400 mm dia 56 No / 33.60 M 1.00 56 No / 33.60 M
(ix) 450 mm dia 44 No / 26.40 M 1.00 44 No / 26.40 M
(x) 500 mm dia 40 No / 24.00 M 1.00 40 No / 24.00 M
(xi) 600 mm dia 32 No / 19.20 M 1.00 32 No / 19.20 M
17 R.C.C pipe and A.C pipe
(i) 100 mm dia 145 No*2M=290M 1.00 290.00M
(ii) 125 mm dia 100 No*2M=200M 1.00 200.00M
(iii) 150 mm dia 90 No*2M=180M 1.00 180.00M
(iv) 200 mm dia 40No*2.5M=100M 1.00 40No*2.5M=100M
(v) 250 mm dia 30No*2.50M=75M 1.00 75.00M
(vi) 300 mm dia 24 No*2.5=60M 1.00 60.00M

63 BCD/SOR_8th Edition_October 2016

 Net payable Volume
S. No Materials Truck Capacity
or weight col 3*col 4
1 2 3 4 5
(vii) 350 mm dia 19No*2.5M=47.5M 1.00 47.50M
(viii) 400mm dia & 450mm dia 13No*2.5M=32.5M 1.00 32.50M
(ix) 500mm dia & 600mm dia 10No*2.5M=25.0M 1.00 25.00M
(x) 700mm dia & 800mm dia 6No*2.5M=15M 1.00 15.00M
(xi) 900mm dia & 1100mm dia 4No*2.5M=10M 1.00 10.00M
(xii) 1100mm dia & 1200mm dia 3No*2.5M=7.5M 1.00 7.50M
G.I crates 1*1.5*0.75 M 80 No 1.00 80 No
18 Bamboos
(i) 75 mm dia & 100 mm dia 280 No 1.00 280 No
(ii) 50 mm dia & 75 mm dia 300 No 1.00 300 No
19 Empty bags of cement length 3000 Nos 1.00 280 Nos
20 Sal bullah Av 6M
(i) 100 mm dia 125 Nos 1.00 125 Nos
(ii) 125 mm dia 80 Nos 1.00 80 Nos
(iii) 150 mm dia 60 Nos 1.00 60 Nos
(iv) 175 mm dia 45 Nos 1.00 45 Nos
(v) 200 mm dia 25 Nos 1.00 25 Nos
(vi) 225 mm dia 20 Nos 1.00 20 Nos
20 Stone chips and sand 5.4 cum 0.92 5.00 cum
21 Steel and C.I.Pipe 3.66 M
(i) 100 mm dia 80 No*3.66M=292.80M 1.00 292.8M
(ii) 125 mm dia 60 No*3.66M=219.60M 1.00 219.60M
(iii) 150 mm dia 50 No*3.66M=183.00M 1.00 183.00M
(iv) 200 mm dia 30 No*3.66M=109.80M 1.00 109.80M
(v) 250 mm dia 22 No*3.66M=80.52M 1.00 80.52M
(vi) 300 mm dia 17 No*3.66M=62.22M 1.00 62.22M
(vii) 350 mm dia 12 No*3.66M=43.92M 1.00 43.92M
(viii) 400 mm dia 9 No*3.66M=32.94M 1.00 32.94M
(ix) 500 mm dia 7 No*3.66M=25.62M 1.00 25.62M
(x) 600 mm dia 5 No*3.66M=18.30M 1.00 18.30M

BCD/SOR_8th Edition_October 2016 64

 SUB HEAD : 1.0
CARRIAGE OF MATERIAL
 CARRIAGE OF MATERIALS (By Tipper)

Ref. to
Sr Rate Remarks/
M.O.R.T Description Unit Quantity Cost Rs
no. Rs. Input ref.
Spec.
1.1 Loading and Unloading of Stone Boulder/ cum
Stone aggregates/ Sand/ Kanker /Moorum.
Placing tipper at loading point, loading with
front end loader, dumping, turning for
return trip, excluding time for haulage and
return trip
Unit = cum
Taking output = 5.5 cum
Time required for
i) Positioning of tipper at loading point 1 Min
ii) Loading by front end loader 1 cum 13 Min
bucket capacity @ 25 cum per hour
iii) Maneuvering, reversing, dumping and 2 Min
turning for return
iv) Waiting time, unforeseen 4 Min
contingencies etc
Total 20 Min
a) Machinery
Tipper 5.5 tonnes capacity hour 0.330 783.00 258.39 P &M 048
Front end-loader 1 cum bucket capacity @ hour 0.330 1056.0 348.48 P &M 017
25 cum/hour
b) Overhead charges @ 0.1 on (a) 60.69
c) Contractor's profit @ 0.1 on (a+b) 66.76
Cost for 5.5 cum = a+b+c 734.31
Rate per cum = (a+b+c)/ 5.5 133.51
Note Unloading will be by tipping. say Rs.133.60
1.2 Loading and Unloading of Boulders by
Manual Means
Unit = cum
Taking output = 5.5 cum
a) Labour
Mate day 0.110 222.00 24.42 L-12
Mazdoor for loading and unloading day 0.750 206.00 154.50 L-13
b) Machinery
Tipper 5.5 tonne capacity hour 0.750 783.00 587.25
c) Overhead charges @ 0.1 on (a+b) 76.62
d) Contractor's profit @ 0.1 on (a+b+c) 84.28
Cost for5.5 cum = a+b+c+d 927.07
Rate per cum = (a+b+c+d)/5.5 168.56
say Rs.169.00
Note Unloading will be by tipping.
1.3 Loading and Unloading of Cement or Steel
by Manual Means and Stacking.
Unit = tonne
Taking output = 10 tonnes
a) Labour
Mate day 0.080 222.00 17.76 L-12
Mazdoor for loading and unloading day 2.000 206.00 412.00 L-13

65 BCD/SOR_8th Edition_October 2016

 Ref. to
Sr Rate Remarks/
M.O.R.T Description Unit Quantity Cost Rs
no. Rs. Input ref.
Spec.
b) Machinery
Truck 10 tonne capacity hour 2.000 805.00 1610.00
c) Overhead charges @ 0.1 on (a+b) 203.98
d) Contractor's profit @ 0.1 on (a+b+c) 224.37

Cost for10 tonnes = a+b+c+d 2468.11

Rate per tonnes = (a+b+c+d)/10 246.81
say Rs.247.00
1.4 Cost of Haulage Excluding Loading and
Unloading
Haulage of materials by tipper excluding
cost of loading, unloading and stacking.

Unit = t.km
Taking output 10 tonnes load and lead 10
km = 100 t.km
(i) Surfaced Road
Speed with load : 25 km / hour.
Speed while Returning empty :35 km / hour.
a) Machinery.
Tipper 10 tonne capacity
Time taken for onward haulage with load hour 0.400 783.00 313.20

Time taken for empty return trip. hour 0.290 783.00 227.07
b) Overhead charges @ 0.1 on (a) 54.03
c) Contractor's profit @ 0.1 on (a+b) 59.43
cost for 100 t km = a+b+c 653.73
Rate per t.km = (a+b+c)/100 6.54
say Rs.6.50
1.4 (ii) Unsurfaced Graveled Road
Speed with load: 20 km / hour
Speed for empty return trip :30 km / hour
a) Machinery
Tipper 10 tonnes capacity
Time taken for onward haulage with load hour 0.500 783.00 391.50

Time taken for empty return trip hour 0.330 783.00 258.39
b) Overhead charges @ 0.1 on (a) 64.99
c) Contractor's profit @ 0.1 on (a+b) 71.49
Cost for 100 t .km = a+b+c 786.37
Rate per t.Km = (a+b+c)/100 7.86
say Rs.7.90
1.4 (iii) Katcha Track and Track in River Bed/Nallah
Bed and Choe Bed.
Speed with load :10 km / hour
Speed while returning empty:15 km / hour
a) Machinery
Tipper 10 tonnes capacity
Time taken for onward haulage hour 1.000 783.00 783.00
Time taken for empty return trip hour 0.670 783.00 524.61
b) Overhead charges @ 0.1 on (a) 130.76
c) Contractor's profit @ 0.1 on (a+b) 143.84
Cost for 100 t .km = a+b+c 1582.21
Rate per t.Km = (a+b+c)/100 15.82
say Rs.15.80

BCD/SOR_8th Edition_October 2016 66

 CARRIAGE OF MATERIALS (By Tractor)

Quantity
Ref. to
Sr Remarks/
M.O.R.T Description Unit Rate Rs. Cost Rs
no. Input ref.
Spec.
1.1 Loading and Unloading of Stone Boulder/Stone cum
aggregates/Sand/Kanker/Moorum.
Placing tipper at loading point, loading with
front end loader, dumping, turning for return
trip, excluding time for haulage and return trip
Unit = cum
Taking output = 2.25 cum
Time required for
i) Positioning of tipper at loading point 1 Min
ii) Loading by front end loader 1 cum bucket 5 Min
capacity @ 25 cum per hour
a) Labour
Mate day 0.030 222.00 6.66 L-12
Mazdoor for loading and unloading day 0.720 206.00 148.32 L-13
Total 6 Min
a) Machinery
Tractor 3.6 tonnes tonnes capacity hour 0.100 402.00 40.20 P &M 048
Front end-loader 1 cum bucket capacity @ 25 hour 0.083 1056.0 87.65 P &M 017
cum/hour
c) Overhead charges @ 0.1 on (a+b) 28.28
d)Contractor's profit @ 0.1 on (a+b+c) 31.11
Cost for2.25 cum = a+b+c+d 342.22
Rate per cum = (a+b+c+d)/2.25 152.10
say Rs.152.00
Note Unloading will be by tipping.
1.2 Loading and Unloading of Boulders by Manual
Means
Unit = cum
Taking output =2.25cum
a) Labour
Mate day 0.050 222.00 11.10 L-12
Mazdoor for loading and unloading day 0.310 206.00 63.86 L-13
b) Machinery
Tipper 3.6 tonne capacity hour 0.310 402.00 124.62
c) Overhead charges @ 0.1 on (a+b) 19.96
d)Contractor's profit @ 0.1 on (a+b+c) 21.95
Cost for2.25 cum = a+b+c+d 241.49
Rate per cum = (a+b+c+d)/2.25 107.33
Note Unloading will be by tipping. say Rs.107.00
1.3 Loading and Unloading of Cement or Steel by
Manual Means and Stacking.
Unit = tonne
Taking output = 3.6 tonnes
a) Labour
Mate day 0.030 222.00 6.66 L-12
Mazdoor for loading and unloading day 0.720 206.00 148.32 L-13
b) Machinery
Trractor of 3.6 tonnes capacity hour 0.720 402.00 289.44

67 BCD/SOR_8th Edition_October 2016

 Quantity
Ref. to
Sr Remarks/
M.O.R.T Description Unit Rate Rs. Cost Rs
no. Input ref.
Spec.
1.3 c) Overhead charges @ 0.1 on (a+b) 44.44
d) Contractor's profit @ 0.1 on (a+b+c) 48.89
Cost for10 tonnes = a+b+c+d 537.75
Rate per tonnes = (a+b+c+d)/2.25 149.37
say Rs.149.00
1.4 Cost of Haulage Excluding Loading and
Unloading
Haulage of materials by tipper excluding cost of
loading, unloading and stacking.
Unit = t.km
Taking output 3.6 tonnes load and lead 10 km =
36 t.km
(i) Surfaced Road
Speed with load :15 km / hour.
Speed while Returning empty :25 km / hour.
a) Machinery.
Tractor 3.6 tonne capacity
Time taken for onward haulage with load hour 0.667 402.00 268.13
Time taken for empty return trip. hour 0.400 402.00 160.80
b) Overhead charges @ 0.1 on (a) 42.89
c) Contractor's profit @ 0.1 on (a+b) 47.18
cost for 36 t km = a+b+c 519.01
Rate per t.km = (a+b+c)/36 14.42
say Rs.14.40
1.4 (ii) Unsurfaced Graveled Road
Speed with load: 12 km / hour
Speed for empty return trip :20 km / hour
a) Machinery
Tractor 3.6 tonne capacity
Time taken for onward haulage with load hour 0.833 402.00 334.87
Time taken for empty return trip hour 0.500 402.00 201.00
b) Overhead charges @ 0.1 on (a) 53.59
c) Contractor's profit @ 0.1 on (a+b) 58.95
cost for 36 t km = a+b+c 648.40
Rate per t.km = (a+b+c)/36 18.01
say Rs.18.00
1.4 (iii) Katcha Track and Track in River Bed/Nallah Bed
and Choe Bed.
Speed with load :10 km / hour
Speed while returning empty:15 km / hour
a) Machinery
Tractor 3.6 tonne capacity
Time taken for onward haulage hour 1.000 402.00 402.00
Time taken for empty return trip hour 0.667 402.00 268.13
b) Overhead charges @ 0.1 on (a) 67.01
c) Contractor's profit @ 0.1 on (a+b) 73.71
cost for 36 t km = a+b+c 810.86
Rate per t.km = (a+b+c)/36 22.52
say Rs.22.50
Note : oSls LFky tgk¡ ij Truck ,oa Tipper ds }kjk <qykbZ fd;k tkuk laHko ugh gS rFkk Tractor ls
<qykbZ Economical gks dsoy oSls gh LFkyks ds fy, Tractor ls <qykbZ dk izko/kku fd;k tk;A
BCD/SOR_8th Edition_October 2016 68
SUB HEAD : 2.0
EARTH WORK
 BUILDING WORK - Contd.

2.0 Earth Work

Code
Description Unit Rate Rs.
No.
2.1 Earth work in surface excavation not exceeding 30 cm in depth but
exceeding 1.5 m in width as well as 10 sqm on plan including
disposal of excavated earth upto 50 m and lift upto 1.5 m disposed
soil to be leveled and neatly dressed :
2.1.1 All Kinds of soil 100sqm 3274.40
2.2 Earth work in rough excavation , banking excavated earth in layer
not exceeding 20 cm in depth , breaking clods watering , rolling
each layer with 1/2 tonne roller or wooden or steel rammers and
rolling every 3rd and top-most layer with power roller of minimum 8
tonnes and dressing up in embankments for roads, flood banks ,
marginal banks and guide banks or filling up ground depressions.
lead upto 50 m and lift upto 1.5 m.
2.2.1 All Kinds of soil cum 248.40
2.3 Banking excavated earth in layers not exceeding 20 cm in depth,
breaking clods, watering .rolling each layer with 1/2 tonne roller, or
wooden or steel rammers, and rolling every 3rd and top-most layer
with power roller of minimum 8 tonnes and dressing up ; in
embankments for roads, flood banks, marginal banks, and guide
banks etc . lead upto 50 m and lift upto 1.5 m.
2.3.1 All Kinds of soil cum 159.00
2.4 Deduct for not rolling with power roller of minimum 8 tonnes for cum 2.90
banking excavated earth in layers not exceeding 20 cm in depth.
2.5 Deduct for not watering the excavated earth for banking. cum 10.70
2.6 Earth work in excavation over areas ( exceeding 30 cm in depth.
1.5 m in width as well es 10 sqm on plan) including disposal of
excavated earth , lead upto 50 m and lift upto 1.5 m; disposed earth
to be levelled and neatly dressed.
2.6.1 AH Kinds of soil cum 225.40
2.7 Earth work in excavation over areas (exceeding 30 cm in depth, 1.5
in width as well as 10 sqm on plan ) including disosal of excavated
earth, lead upto 50 m and lift upto 1.5 m , disposed earth to be
levelled and neatly dressed :
2.7.1 Ordinary rock cum 336.80
2.7.2 Hard rock (requiring blasting ) cum 453.80
2.7.3 Hard rock (blasting prohibited) cum 721.60
2.8 Earth work in excavation in foundation trenches or drains(not
exceeding 1.5 m in width or 10 sqm on plan) including dressing of
sides and ramming of bottoms, lift upto 1.5 m . including getting out
the excavated soil and disposal of surplus excavated soil as
directed, within a lead of 50 m.
2.8.1 All Kinds of soil cum 230.50

69 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
2.9 Excavation work in foundation trenches or drains not exceeding 1.5 m
in width or 10 sq.m on plan including dressing of sides and ramming of
bottoms lift upto 1,5m, including getting cut the excavated soil and
disposal of surplus excavated soiis as directed, within a lead of 50 m .

2.9.1 Ordinary rock cum 372.00

2.9.2 Hard rock (requiring blasting) cum 502.60
2.9.3 Hard rock (Blasting Prohibited) cum 745.30
2.10 Excavating trenches of required width for pipes cables, etc, including
excavation for sockets, and dressing of sides, ramming of bottoms,
depth upto 1.5 m including getting out the excavated soil , and then
returning the soil as required , in layers not exceeding 20 cm in depth
including consolidating each deposited layer by ramming, watering, etc.
and disposing of surplus excavated soil as directed , within a lead of 50
m.
2.10.1 All kinds of soil.
2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. m 144.10
2.10.1.2 Pipes, cables etc. exceeding 80 mm dia . But not exceeding m 235.40
300mm dia.
2.10.1.3 Pipes , cables etc. exceeding 300m dia. m 367.50
2.11 "Extra for excavating trenches for pipes, cables etc.in all kinds of soil for metre 131.60
depth exceeding 1.5 m , but not exceeding 3 m.(Rate is over
corresponding basic item for depth upto 1.5 meter.)
2.12 *Extra for excavating trenches for pipes, cables etc.in all kinds of soil m 337.00
exceeding 3 m in depth , but not exceeding 4.5 m.(Rate is over
corresponding basic item for depth upto 1.5 meater.)
2.13. Excavating trenches of required width for pipes cables, etc, including
excavation for sockets, depth upto 1.5 m including getting out the
excavated materials , returning the soil as required in layers not
exceeding 20 cm in depth including consolidating each deposited layer
by ramming, watering, etc. stacking serviceable material for
measurements and disposed ' of unserviceable material as directed,
within a lead of 50 m:
2.13.1 Ordinary rock :
2.13.1.1 Pipes, cables etc. not exceeding 80 mm dia m 211.30
2.13.1.2 Pipes, cables etc exceeding 80 mm dia but not exceeding m length 523.30
300 mm dia of pipe
2.13.1.3 Pipes, cables etc exceeding 300 mm dia m length 602.30
2.13.2 Hard rock (requiring blasting)
2.13.2.1 Pipes, cables etc. not exceeding 80 mm dia. m length 275.50
2.13.2.2 Pipes, cablets etc. exceeding 80 mm dia, but not exceeding m length 682.20
300 mm dia. of pipe
2.13.2.3 Pipes, cables tec. Exceeding 300 mm dia. m length 785.20
2.13.3 Hard rock (blasting prohibited)
2.13.3.1 Pipe, cables etc. not exceeding 80 mm dia. m length 387.80
2.13.3.2 Pipes, cables etc. exceeding 80 mm dia. But not exceeding m length 960.10
300 mm dia. of pipe
2.13.3.3 Pipes, cables etc. exceeding 300 mm dia. m length 1105.20

BCD/SOR_8th Edition_October 2016 70

Code
Description Unit Rate Rs.
No.
2.14 Extra for excavating trenches for pipes, cables, etc.in ordinary/hard rock m length 102.70
exceeding 1.5 m in depth but not exceeding 3 m.(Rate is over of pipe
corresponding basic item for depth upto 1.5 metre.)
2.15 Extra for excavating trenches for pipes, cables, etc.in ordinary/hard rock m length 254.30
exceeding 3m in depth but not exceeding 4.5 m. (Rate is over of pipe
corresponding basic item. For depth upto 1.5 metre.)
2.16 Close timbering in trenches including strutting. Shoring and packing
cavities (wherever required) complete. (Measurements to be taken of
the face area timbered):
2.16.1 Depth not exceeding 1.5 m. sqm 108.60
2.16.2 Depth exceeding 1.5 m but not exceeding 3 m. sqm 111.80
2.16.3 Depth exceeding 3m but not exceeding 4.5 m sqm 120.00
2.17 Close timbering in case of shafts, wells, cesspits, mannoies
and the like including strutting, shoring and packing cavities
(wherever required) complete (Measurements to.be taken of
the face area timbered):
2.17.1 Depth not exceeding 1.5 m. sqm 111.20
2.17.2 Depth exceeding 1.5 m but not exceeding 3 m sqm 119.50
2.17.3 Depth exceeding 3 m but not exceeding 4.5 m sqm 128.10
2.18 Close timbering over areas including strutting, shoring and packing,
cavities (wherever required) etc. complete (Measurements to be taken
of the face area timbered):
2.18.1 Depth not exceeding 1.5 m. sqm 96.20
2.18.2 Depth exceeding 1.5 m but not exceeding 3 m sqm 100.60
2.18.3 Depth exceeding 3 m but not exceeding 4.5 m. sqm 105.50
2.19 Extra for planking, strutting and packing materials for cavities i(in close sqm 1451.00
timbering) if required to be left permanently in position (Face area of
timber permanently left to be measured)
2.20 Open timbering in trenches including strutting and shoring complete
(Measurements to be taken of the face area timbered).
2.20.1 Depth not exceeding 1.5 m. sqm 56.00
2.20.2 Depth exceeding 1.5 m but not exceeding 3 m sqm 58.50
2.20.3 Depth exceeding 3 m but not exceeding 4. m. sqm 62.40
2.21 Open timbering in case of shafts, wells, cesspits, manholes and the like
including strutting and shoring complete (measurements to be taken of
the face area timbered):
2.21.1 Depth not exceeding 1.5 m sqm 47.50
2.21.2 Depth exceeding 1.5 m but not exceeding 3 m sqm 51.30
2.21.3 Depth exceeding 3 m but not exceeding 4.5 m sqrn 56.30
2.22 Open timbering over areas including strutting, shoring and use and
waste of raking shores, complete (Measurements to be taken of the
face area timbered)
2.22.1 Depth not exceeding 1.5 sqm 32.40
2.22.2 Depth exceeding 1.5 m but not exceeding 3 m sqm 35.20
2.22.3 Depth exceeding 3 m but not exceeding 4.5 m sqm 39.60

71 BCD/SOR_8th Edition_October 2016

Code
Description Unit Rate Rs.
No.
2.23 Extra for planking and strutting in open timbering if required to be left sqm 747.50
permanently in position (face area of the timber permanently left to be
measured).
2.25 Pumping out water caused by springs, tidal or river seepage, broken Kl 68.50
water mains or drains and the like.
2.26 Filling available excavated earth (excluding rock) in trenches, plinth, cum 74.50
sides of foundations etc. in layers not exceeding 20 cm in depth:
consolidating each deposited layer by ramming and watering lead
2.27 Extra for every additional lift of 1.5 m or part thereof in :
2.27.1 Ali kinds of soil. cum 29.20
2.27.2 Ordinary or hard rock cum 52.40
2.28 Supplying and Filling in plinth with local sand and under floors including, cum 204.40
watering, ramming consolidating and dressing complete.
2.29 Surface dressing of the ground including removing vegetation and
inequalities not exceeding 15 cm deep and disposal of rubbish, lead
upto 50 m and lift upto 1.5 m
2.29.1 All kinds of soil. 100sqm 806.00
2,30 Ploughing the existing ground to a depth ot 15 cm to 25 cm and
watering the same:
2.30.1 All kinds of soil. 100sqm 798.90
2.31 Excavating holes upto 0.5 cum including getting out the excavated soil,
then returning the soil as required in layer not exceeding 20 cm in
depth, including consolidating each deposited layer by ramming,
watering etc, disposing of surplus excavated soil; as directed within a
lead of 50 m and lift upto 1.5m:
2.31.1 All kinds of soil. hole 70.20
2.31.3 Ordinary rock hole 113.10
2.31.4 Hard rock(requiring blasting) hole 151.20
2.31.5 Hard rock (blasting prohibited) hole 223.90
2.32 Clearing jungle including uprooting of rank vegetation ,grass, brush 100sqm 414.40
wood, trees and saplings of girth upto 30 cm measured at a height of 1
m above ground level and removal of rubbish upto a distance of 50 m
outside the periphery of the area cleared.
2.33 Clearing grass and removal of the rubbish upto a distance of 50 m 100sqm 212.70
outside the periphery of the area cleared.
2.34 Felling trees of the girth (measured at a height of 1 m above ground
level) including cutting of trunks and branches removing the roots and
stacking of serviceable material and disposal of unserviceable material:
2.34.1 Beyond 30cm girth upto and including 60 cm girth tree 128.90
2.34.2 Beyond 60 cm girth upto and including 120 cm girth tree 565.60
2.34.3 Beyond 120 cm girth upto and including 240 cm girth tree 2603.40
2.34.4 Above 240 cm girth tree 5229.00
2.35 Supplying chemical emulsion in sealed containers including delivery as
specified.
2.35.1 Chlorpyriphos/Lindone emulsifiable concentrate of 20% litre 195.40

BCD/SOR_8th Edition_October 2016 72

Code
Description Unit Rate Rs.
No.
2.37. Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL
anti-termites' treatrnent(including the cost of chemical emulsion)

2.37.1 Along external wall where the apron is not provided using
chemical imulsion @ 7.5 liters / sqm of the vertical surface of
the substructure to a depth of 300 mm including excavation
channel along the wall & rodding etc. complete:
2.37.1.1 With chlorpyriphos/Lindone E.C. 20% with 1% concentration m 32.70

2.37.2 Along the external wall below concrete or masonry apron

using chemical emulsion @ 2.55 litres per linear metre
including drilling and plugging holes etc.
2.37.2.1 With chlorpyriphos E.C. 20% with 1% concentration m 39.10
2.37.3 Treatment of soil under existing floors using chemical
emulsion @ one litre per hole, 300 mm apart including drilling
and plugging 12 mm diameter holes with cement mortar 1:2
(1 cement: 2 coarse sand) to match the existing floor.
2.37.3.1 With Chlorpyriphos EC 20% with 1% concentration sqm 186.70
2.37.4 Treatment of existing masonry using chemical emulsion@
one litre per hole at 300 mm interval including drilling holes at
45 degree and plugging them with cement mortar 1:2(1
cement:2 coarse sand) to the full depth of the hole.
2.37.4.1 With chlorpyriphos EC 20% with 1% concentration m 45.60
2.37.5 Treatment at points of contact ot wood work by chemical m 222.80
emulsion chlordane. (in oil or kerosene based solution)® 0.5
litres per hole by drilling 6 mm dia holes at downward angle
of 45 degree at 150 mm centre to centre and sealing the
same.
2.38 Deduct for disposed soil not levelled and neatly dressed. cum 22.50
2.39 Supply and stacking of Fly ash conforming to IRC- 58 at site, excluding cum 9.50
carriage,loading , unloading & stacking up to any lead (measured
stacks will be reduced by20% for payment).
2.40 Filling with available fly ash and earth (excluding rock) in trenches or cum 74.50
embankment in layers (each layer should not exceed 15 cm), with
intermediate layer of compacted earth (Soil density of 98%) after every
four layers of compacted depth of fly ash, sides & top layer of filling
shall be done with earth having total minimum compacted thickness 30
cm or as decided by Engineer – in-charge, including compacting each
layer by rolling/ ramming and watering , all complete as per drawing and
direction of Engineer -in - charge.

73 BCD/SOR_8th Edition_October 2016

SUB HEAD : 3.0
MORTARS
 BUILDING WORK - Contd.

3.0 Mortars

Code No. Description Unit Rate Rs.

2103 Lime mortar 1:1:1 (1 time putty:1Surkhi:1 coarse sand) cum 2337.00

2144 Lime mortar 1:1:2(1 lime putty:1 surkhi:2coarse sand) cum 1932.60

2104 Lime mortar 1:2(1 time putty:2 surkhi) cum 3130.80

2145 Lime mortar 1:3(1 lime putty:3 surkhi) cum 3122.60

2146 Lime mortar 1:3(1 lime putty :3 coarse sand) cum 1337.60

2110 Cement Mortar 1:1 (1 cement : 1 fine sand). cum 6766.80

2111 Cement mortar 1:2 (1 cement :2 coarse sand ) cum 4730.10

2112 Cement mortar 1:3(1 cement:3 coarse sand) cum 3712.20

2113 Cement mortar 1:4(1 cement:4 coarse sand) cum 2907.10

2114 Cement mortar1:5(1 cement:5 coarse sand) cum 2473.60

2115 Cement mortar 1:6(1 cement:6 coarse sand) cum 2102.10

2128 White cement mortar 1:2 (1 White cement :2 marble dust) cum 11350.10

2128A Cement mortar 1:2 (1 cement : 2 marble dust). cum 5555.80

2125 Cement lime mortar 1:1:3(1 cement :1 lime putty:3 coarse sand) cum 3691.50

2126 Cement lime mortar 1:1:6 (1 cement:1 lime putty:6 coarse sand) cum 2551.60

74 BCD/SOR_8th Edition_October 2016

 SUB HEAD : 4.0
CONCRETE WORK
 BUILDING WORK - Contd.

4.0 Concrete work

Code
Description Unit Rate Rs.
No.
4.1 Providing and laying in position cement concrete of specified
grade exluding the cost of centring and shuttering-all work upto
plinth level.
4.1.1 1:1:2 ( 1 cement: 1 coarse sand:2 graded stone aggregate 20 cum 5871.60
mm nominal size)
4.1.2 1:1.5:3(1 Cement :1.5 coarse sand:3 graded stone aggregate cum 4373.20
20 mm nominal size)
4.1.3 1:2:4(1 Cement: 2 coarse sand:4 graded stone aggregate 20 cum 3850.50
mm nominal size)
4.1.4 1:2:4 (1 Cement: 2 coarse sand : 4 graded stone aggregate 40 cum 3740.20
mm nominal size)
4.1.5 1:3:6 (1 Cement: 3 coarse sand : 6 graded stone aggregate 20 cum 3174.30
mm nominal size)
4.1.6 1:3:6 (1 Cement; 3 coarse sand :6 graded stone aggregate 40 cum 3030.20
mm nominal size)
4.1.8 1.4.8 (1 Cement :4 coarse sand :8 graded stone agregate 40 cum 2670.60
mm nominal size)
4.1.10 1:5:10(1 Cement :5 coarse sand:10 graded stone aggregate 40 cum 2382.80
mm nominal size)
4.2 Providing and laying cement concrete in retaining walls, return
walls, walls (any thickness) including attached
pilasters,columns,piers, abutments, pillars, post. struts,
buttresses, string or lacing courses,parapets, coping,bed
blocks, anchor blocks, plin window sills, fillets etc. upt floor five
level excluding the cost of centring,shuttering and finishing:
4.2.1 1:1:2 (1 Cement:1 coarse sand : 2 graded stone aggregate 20 cum 6618.30
mm nominal size)
4.2.2 1:1.5:3(1 Cement: 1:5 coarse sand : 3 graded stone aggregate cum 5114.70
20 mm nominal size)
4.2.3 1:2:4 (1 Cement :2 coarse sand :4 graded stone aggregate 20 cum 4569.00
mm nominal size)
4.2.4 1:2:4(1 Cement :2 coarse sand :4 graded stone aggregate 40 cum 4458.70
mm nominal size)
4.2.5 1:3:6 (1 Cement: 3 coarse sand: 6 graded stone aggregate 20 cum 3892.70
mm nominal size)
4.2.6 1:3:6 (1 Cement :3 coarse sand:6 graded stone aggregate 40 cum 3748.70
mm nominal size)
4.3 Centring and shuttering including strutting,propping etc. and
removal or form work for
4.3.1 Foundations,footings, bases Columns sqm 168.70
4.3.2 Retaining walls,return walls, walls (any thickness) including sqm 432.50
attached pilasters, buttresses, plinth and string courses fillets
etc.

75 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
4.3.3 Columns, piers.abutments, pillars,posts and struts sqm 357.60
4.4 Providing and faying cement concreate in kerbs, steps and the
like at or near ground level excluding the cost of centring,
shuttering and finishing.
4.4.1 1:2:4 (1 Cement :2 coarse sand :4 grade stone aggregate 20 cum 3850.50
mm nominal size)
4.4.2 1:3:6 (1 Cement:3 coarse sand:6 graded stone aggregate 20 cum 3174.30
mm nominal size)
4.5 Providing and fixing up to floor five level precast cement
concrete string or lacing courses, copings, bed plates, anchor
blocks, plain window sills, shelves, louvers, steps, stair cases,
etc. including hoisting and setting in position with cement mortar
1:3 (1 cement : 3 coarse sand), cost of required centering,
shuttering complete.
4.5.1 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate cum 5718.40
20 mm nominal size).
4.5.2 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate cum 5111.30
20 mm nominal size).
4.5.3 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate cum 4325.80
20 mm nominal size).
4.6 Providing and fixing at or near ground level precast cement
concrete in kerbs, edgings etc. as per approved pattern and
setting in position with cement mortar 1:3 (1 cement : 3 coarse
sand), including the cost of required centering, shuttering
complete.
4.6.1 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 cum 3408.00
mm nominal size).
4.7 Providing and fixing up to floor five level precast cement
concrete solid block,including hoisting and setting in position
with cement mortar 1:3 (1 cement : 3 coarse sand), cost of
required centering, shuttering complete.
4.7.1 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 cum 5736.50
mm nominal size).
4.8 Providing and fixing up to floor five level precast cement
concrete hollow block,including hoisting and setting in position
with cement mortar 1:3 (1 cement : 3 coarse sand), cost of
required centering, shuttering complete.
4.8.1 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate cum 5047.10
20mmnominal size).
4.11 Providing and laying damp-proof Course 50 mm thick with sqm 251.20
cement concrete 1:2:4(1cement:2:2 coarse sand :4 graded
stone aggregate 20mm nominal size)

BCD/SOR_8th Edition_October 2016 76

Code
Description Unit Rate Rs.
No.
4.12 Extra for providing and mixing water prooding material in per 50 46.58
cement concrete work in the proportion recommended by the kg
manufacturers. cement
4.13 Applying a coat of residual petroleum bitumen of grade of VG- sqm 105.40
10 of approved quality using 1.7 kg. per square metre on damp
oroof course after cleaning the surface with brushes and finally
with a piece of cloth lightly soaked in kerosene oil.
4.14 Extra for concrete work in superstructure above floor V level for cum 383.60
each four floors of part thereof.
4.15 Extra for laying concrete in or under water and/or liquid mud cum per 293.00
including cost of pumping or bailing out water and removing m depth
slush etc. complete (The quantity will be calculated by
multiplying the depth measured form the sub-soil water level
upto centre of graity of concrete under sub-soil water water
level with quantity of concrete in cum executed uder sub-soil
water. The depth of centre of gravity shall be reckoned correct
to 0.1 m. 0.05 m or more shall be taken as 0.1 m and less than
0.05 m ignored.)
4.16 Extra for laying conrete in or under foul positions. cum 111.20
4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 sqm 359.80
(1 cement :3 coarse sand : 6 graded stone aggregate 20 mm
nominal size) over 75 mm thick bed of dry brick ballast 40 mm
nominal size, well rammed and consolidated and grouted with
fine sand, including finishing the top smooth.
4.19 Extra for using 12.5/10 mm nominal size graded/single size cum 53.60
stone aggregate instead of 20 mm nominal size graded stone
aggregate in cement concrete/reinforced cement concrete
1:2:4(1 cement:2 coarse sand:4 graded stone aggregate 20 mm
nominal size)

77 BCD/SOR_8th Edition_October 2016

 SUB HEAD : 5.0
REINFORCED CEMENT
CONCRETE
 BUILDING WORK - Contd.

5.0 Rainforced Cement Concrete

Code Unit Rate Rs.
Description
No.
5.1 Providing and laying in position specified grade of reinforced
cement concrete excluding the cost of centring,shuttering,finishing
and reinforcement-All work puto plinth level
5.1.1 1:1:2 (1 cement:1 coarse sand:2 graded stone aggregate cum 6035.20
20mm nominal size)
5.1.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone cum 4530.30
aggregate 20 mm nominal size)
5.1.3 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate cum 3984.50
20 rr,m nominal size)
5.2 Reinforced cement concrete work in wall (any thickness), including
attached pilasters, buttresses, plinth and string courses, fillets,
columns, pillars, piers, abutments, posts and struts, etc. upt floor
five level excluding cost of centring, shuttering, finishin and
reinforcement.
5.2.1 1:1:2 (1 cement: 1 coarse sand: 2 graded stone cum 6644.60
aggregate 20 mm nominal size)
5.2.2 1:1:5:3(1 cement: 1.5 coarse sand:3 graded stone cum 5139.70
aggregate 20mm nominal size)
5.2.3 1:2:4(1 cement :2 coarse sand:4 graded stone aggregate cum 4593.90
20 mm nominal size)
5.3 Reinforced cement conrete work in beams,suspended floors, roofs cum 4671.80
having slope upto 15, landings,balconiec, shelves, chajjas, lintels,
bands, plain window sills, staircases and spiral stair cases upto
floor five level excludingthe cost of centring, shuttering, finishing
and reinforement with 1:2:4(1 cement:2 coarse sand:4 graded
stone aggregate 20 mm nominal size).
5.4 Providing and laying upto floor five level reinforced cement cum 4444.30
concrete in kerbs, steps and the like excluding the cost of
centring,shuttering, finishing and reinforcement with 1:2:4(1
cement:2 coarse sand:4 graded stone aggregate 20mm nominal
size).
5.5 Reinforced cement concrete work in arhes, archribs, domes, vaults, cum 4850.80
0
shells, folded plate and roofs having slope more than 15 upto floor
five level excluding the cost of centring. Shuttering. Finishing and
reinforement with 1:2:4(1 cement:2 coarse sand :4 graded stone
aggregate 20mm nominal size)
5.6 Reinforced cement concrete work in chimnys shafts, upto floor five cum 4660.30
level excluding the cost of centring, shuttering, finishing and
reinforement with 1:2:4(1 cement:2 coarse sand:4 graded stone
aggregate 20 mm nominal size)
5.7 Reinforced cement concrete work in well-steining excluding the cum 3870.90
cost of centrin,shuttering, finishing and reinforcement with 1:2:4 (1
cement:2 coarse sand:4 graded stone aggregate 20 mm nominal
size)

78 BCD/SOR_8th Edition_October 2016

 Code Unit Rate Rs.
Description
No.
5.8 Reinforced cement concrete work in Vertical and Horizontal fins
individually or forming box louvers, facias and eaves boards upto
floor five level eciuding the cost of centring, shuttering, finishing
and reinforcement with 1:1.5:3 (1 cement:1.5coarse sand: 3graded
stone aggregate 20mm nominal size) cum 4879.00
5.9 Centring and shuttering including strutting,propping etc. and
removal of form for.
5.9.1 Foundations, footings, bases of columns etc. for mass
concrete. sqm 169.00
5.9.2 Walls (any thickness) including attached pilasters.
Butteresses, plinth and string courses etc. sqm 262.30
5.9.3 Suspended floors, roots, landings, balcnies and access
platform. sqm 291.00
5.9.4 Shelves (Cost in situ) sqm 291.00
5.9.5 Lintels, beams, plinth bams, griders, bressumers and
contilevers. sqm 261.70
5.9.6 Columns,Pillars, Piers, Abutments, Posts and Struts sqm 357.60
5.9.7 Stairs,(excluding landings) except spiral-staircaces. sqm 328.90
5.9.8 Spiral staircases (including landing) sqm 283.40
.5.9.9 Arches,domes,vaults upto 6m span sqm 820.10
5.9.10 Extra for arches,domes, vaults exceeding 6 m span sqm 262.60
5.9.11 Chimneys and shafts sqm 432.50
5.9.12 Well steining sqm 243.30
5.9.13 Vertical and horizontal fins individually or forming box
louvers band, facias and eaves boards sqm 446.10
5.9.14 Extra for shuttering in circular work (20% of respective
centring and shuttering items) sqm 20.20
5.9.15 Small lintels not exceeding 1.5 m clear span, mouldings
as in cornoces, window sills, string, courses, bands,
copings, bed plates, anchor blocks and the like. sqm 183.20
5.9.16 Edges of slabs and breaks in floors and walis-
5.9.16.1 Under 20 cms wide m 83.50
5.9.16.2 Above 20cm wide sqm 393.20
5.9.17 Cornices and mouldings sqm 443.40
5.9.18 Small surfaces such as cantilever ends,brackets and
ends of steps, caps and bases to pilasters and columns
and the like sqm 381.30
5.9.19 Weather shade,Chajjas, corbels etc. including edges sqm 395.60
5.9.20 Suspended floors, roofs, landings, balconies and access
platform with water proofply 12 mm thick. sqm 392.70
5.9.21 Lintels, beams, plinth beams, girders, bressumers and
cantilevers with water proof ply 12 mm thick. sqm 371.80
5.10 Providing and fixing tie bolt, spring coil and plastic cone in wall
shuttering complete as per the direction of engineer-in charge
5.10.1 12 mm dia & 100 mm length sets 147.40
5.10.2 12 mm dia & 150 mm length sets 159.60
5.10.3 20 mm dia & 150mm length sets 153.20
5.10.4 20 mm dia & 225 mm length sets 170.80

BCD/SOR_8th Edition_October 2016 79

Code Unit Rate Rs.
Description
No.
5.11 Extra for additional height in centring, shuttering where ever
required with adequate bracing, propping etc. including cost of de-
shutering and de centring at all levels over a height of 3.5 m ,for
every additional height of 1 metre or part thereof (Plan area to be
measured)
5.11.1 Suspended floors, roots, laning, beams and balconies
(Plan area to be measured) sqm 113.50
5.12 Providing, hoisting and fixing up to floor five level precast
reinforced cement concrete work in string courses, bands, copings,
bed plates, anchor blocks, plain window sills and the like, including
the cost of required centering, shuttering but excluding cost of
reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size). cum 5224.30
5.13 Providing, hoisting and fixing up to floor five level precast
reinforced cement concrete in small lintels not exceeding 1.5 m
clear span up to floor five level,including the cost of required
centering, shuttering but excluding the cost of reinforcement, with
1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm
nominal size). cum 6622.30
5.14 Providing, hoisting and fixing up to floor five level precast
reinforced cement concrete in mouldings as in cornices, windows
sills etc. including setting in cement mortar 1:3 (1 cement : 3 coarse
sand) cost of required centering, shuttering but excluding the cost
of reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size). cum 7335.00
5.15 Providing, hoisting and fixing up to floor five level precast
reinforced cement concrete in lintels, beams and bressumers
including setting in cement mortar 1:3 (1 cement : 3 coarse sand),
cost of required centering and shuttering but excluding the cost of
reinforcement with, 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size). cum 6174.10
5.16 Providing, hoisting and fixing up to floor five level precast
reinforced cement concrete in shelves including setting in cement
mortar 1:3 (1 cement : 3 coarsesand), cost of required centering,
shuttering and finishing with neat cement punning on exposed
surfaces but excluding the cost of reinforcement, with 1:2:4 (1
cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm
nominal size). cum 9581.50
5.17 Providing, hoisting and fixing up to floor five level precast
reinforced cement concrete in vertical & horizontal fins individually
or forming box louvers setting in cement mortar 1:2 (1 cement : 2
coarse sand), including the cost of required centering, shuttering
but excluding the cost of reinforcement, with 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20 mm nominal size). cum 5237.80
5.18 Providing,precast cement concrete Jali 1:2:4(1 cement:2 coarse
sand:4 stone aggregate 6mm nominal size) reinforced with 1.6 mm
dia mild steel wire including roughening cleaning, fixing and
finishing in cement mortar 1:3 (1 cement:3 fine sand) etc.complete
excluding plastering of the jambs, sills and soffits.

80 BCD/SOR_8th Edition_October 2016

 Code Unit Rate Rs.
Description
No.
5.18.1 50 mm thick sqm 571.40
5.18.2 40 mm thick sqm 500.00
5.18.3 25 mm thick cum 463.40
5.19 Encasing rolled steel sections, in beams and columns, with cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 12.5 mm nominal size),including centering and
shuttering complete but excluding cost of reinforcement. cum 6585.30
5.21 Extra for providing and fixing expanded metal mesh of size
20x60mm and strands 3.25 mm wide 1:6 mm thich weighing 3.64
kg. er sqm for encasing of roiled steel sections in beams, columns
and grillages excluding cost of hangers sqm 391.50
5.22 Reinforcement for R.C.C. work including straightening, cutting,
bending, placing in position and binding all complete.
5.22.1 Mild steel 6.00 mm dia kg 54.30
5.22.1A Mild steel 5.5 mm dia kg 54.40
5.22.1B Mild steel 6.0 mm dia kg 54.30
5.22.1C Mild steel 6.5 mm dia kg 54.10
5.22.1D Mild steel 7.0 mm dia kg 53.90
5.22.1E Mild steel 8.0 mm dia kg 53.70
5.22.1F Mild steel 10.0 mm dia kg 54.40
5.22.1G Mild steel 12.0/12.7 mm dia kg 54.40
5.22.7 Thermo-Mechanically Treated bars (FE-500) 20mm dia. kg 53.60
5.22.7A Thermo-Mechanically Treated bars TMTC-500-8mm dia. kg 56.00
5.22.7B Thermo-Mechanically Treated bars TMTC-500-10mm dia. kg 54.70
5.22.7C Thermo-Mechanically Treated bars TMTC-500-12mm dia. kg 53.40
5.22.7D Thermo-Mechanically Treated bars TMT Fe-500-I6mrn dia. kg 54.40
5.22.7E Thermo-Mechanically Treated bars TMT Fe-500-20mm dia. ky 53.60
5.22.7F Thermo-Mechanically Treated bars TMT Fe-500-25rnm dia. kg 53.60
5.22.7G Thermo-Mechanically Treated bars TMT Fe-500-28mm dia. kg 53.60
5.22.7H Thermo-Mechanically Treated bars TMT Fe-500-32mm dia. kg 53.60
5.23 Extra for RCC work in superstructure above floor V level for each
four floors or part thereof. cum 383.60
5.24 Extra for rendering smooth the top of suspended floors, landings
and staircases (treads and risers) with cement mortar 1:2(1
cement:2 coarse sand) including a floating coat of neat cement and
protecting the surface with a layer of 7.5cm of earth laid over 15
mm of fine sand in case of suspended floor and bricks laid in mud
mortar in case of landings and steps including subsequent removal
and cleaning of the same. sqm 65.20
5.25 Providing and fixing in position copper plate as per design for
expansion joints. kg 337.70
5.26 Providng and filling in position, blown bitumen in expansion joints. 100m
(Length)x
1cm(Wide)
x1cm
(Depth) 544.40

BCD/SOR_8th Edition_October 2016 81

 Code
Description Unit Rate Rs.
No.
5.27 Providing and filling in position bitumen mix filler of Proportion 80 kg of 100m 173.29
hot bitumen, 1 kg, of c ement and 0.25 cubicmetre of coarse sand for (Length)x
expansion joints, 1cm(Wide)x
1cm(Depth)
5.28 Providing and fixing in position 12 mm thick bitumen impregnated fibre 100m 445.00
board conforming to IS: 1838 including cost of primer, sealing (Length)x
compound in expansion joints. 1cm(Depth)
5.29 Providng and fixing sheet covering over expansion joints with iron
screws as per design to match the colour/shade of wall treatment,
5.29.1 Asbestos sheet 6 mm thick
5.29.1.1 150 mm wide m 101.80
5.29.1.2 200mm wide m 136.60
5.29.2 Aluminium fluted strips 3.15 mm thick
5.29.2.1 150 mm wide. m 322.50
5.29.2.2 200 mm wide m 451.90
5.30 Add for plaster drip course/groove in plastered surface or moulding to m 20.70
R.C.C. projections.
5.31 Extra for laying reinforced cement concrete in or under water and/or cum 293.00
liquid mud including cost or pumping or bailing out water and
removing slush etc. complete.(Rate same as per item No, 4.29)
Note:- The quantity will be calculated by multiplying the depth
measured from the subsoil water level upto the centre of gravity of the
R.C.C. under subsoil water with the quantity of R.C.C. in cubic metre
executed under subsoil water. The depth of centre of gravity shall be
reconed correct to 0.1 m. 0.05 m or more shall be taken as 0.1 and
less than 0.05 m ignored. No extra payment shall be made for placing
reinforcement or centering & shuttering under subsoil water
conditions.
5.32 Extra for laying reinforced cement concrete in or under foul positions. cum 111.20
5.33A Providing and laying in position machine batched, machine mixed and
machine vibrated design mix cement concrete of specified grade for
reinforced cement concrete structural elements, excluding the cost of
centring, shuttering finishing and reinforcement, M-20 grde reinforcd
cement concrete
5.33A.1 All work upto plinth level cum 4533.30
5.33A.2 All works above plinth level upto floor V level
5.33A.2.1 Walls columns, pillars, posts cind struts cum 4860.50
5.33A.2.2 Beams, planth beams, girders, bressumers, contilevers, cum 5083.80
Suspended floors lintels roofs and staircases including
spiral staircases, shelves etc.
5.33A.3 Extra for R.C.C work above floor V level for each four floors or part cum 383.60
thereof.
5.33B Add or deduct for providing richer or leaner mixes respectively at all
floor levels.
5.33B.1 Proiding M-25 grade R.C.C. instead of M-20 grade R.C.C. cum 194.20
5.33B.2 Providing M-30 grade R.C.C. instead of M-20 grade R.C.C. cum 266.10
5.33B.3 Providing M-35 grade R.C.C. instead of M-20 grade R.C.C. cum 323.67
5.33B.4 Providing M-15grade R.C.C instead of M-20 grade R.C.C. cum 453.10

82 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
5.33 : Providing and laying in position machine batched and machine mixed
design mix M-25 grade cement concrete for reinforced cement
concrete work, using cementcontent as per approved design mix,
including pumping of concrete to site of laying but excluding the cost
of centering, shuttering, finishing and including retard setting of
concrete, improve workability without impairing strength
andadmixtures in recommended proportions as per IS: 9103 to
accelerate,reinforcement,durability as per direction of Engineer-in-
charge. Note:- Cement content considered in this item is @ 330 kg/
cum. Excess or less cement used as per design mix is payable or
recoverable separately.
5.33.1 All works up to plinth level cum 4621.50
5.33 .2: All work above Plinth level upto floor V Level. cum 5102.30
5.34 Add or deduct for providing richer or leaner mixes respectively at all
floor levels.
5.34.1 : Providing M-30 grade concrete by using 340kg /m3 of cum 76.6
Cement per cum of concrete instead of M-25 grade
B.M.C./RMC
5.34.2 Providing M-35 grade concrete by using 350kg /m3 of cum 153.30
Cement per cum of concrete instead of M-25 grade
5.34.3 Providing M-40 grade concrete by using 360kg /m3 of cum 226.70
Cement per cum of concrete instead of M-25 grade
B.M.C./RMC
5.35 Add for using extra cement in the items of design mix over and above quintel 719.3
the specified cement content therein.
5.37.1 Providing and laying in position ready mixed concrete manufactured cum 5010.2
in fully automatic batching plant and transported to site of work in
transit mixer for a lead up to 10kms having continuous agitated mixer,
manufactured as per mix design of specified grade for reinforced
cement concrete work including pumping of R.M.C. from transit mixer
to site of laying , excluding the cost of centering, shuttering finishing
and reinforcement including cost of admixtures in recommended
proportions as per IS : 9103 to accelerate/ retard setting of concrete,
improve workability without impairing strength and durability as per
direction of the Engineer - in - charge. M-25 grade Reinforced cement
concrete by using 330 kg of cement per cum of concrete. All works up
to Plinth level
5.37.2 All works above Plinth level up to floor five level. cum 5867.70
5.38 Extra for R.C.C/ B.M.C/ R.M.C. work above floor V level for each four cum 176.00
floors or part thereof.
5.41 Supplying and applying pre tested and approved water based
concrete curing compound to concrete/ masonry surface, all as per
manufacturer’s specification and direction of Engineer-in-charge.
5.41.1 Non pigmented wet curing compound. sqm 85.20
5.41.2 Pigmented wet curing compound. 99.80

BCD/SOR_8th Edition_October 2016 83

 Code
Description Unit Rate Rs.
No.
5.42/5.51 Providing and fixing tapered / parallel threaded couplers conforming to
IS code on Reinforcement Couplers for Mechanical Splices of Bars for
Concrete Reinforcement – Specification, to reinforcement bars
including threading,enlargement at connection by forging, protecting
the prepared reinforcement bars and related operations as required to
complete the works as per direction of Engineer-in-Charge . (The
length of the bars in which coupler is to be provided should not be less
than 4 metre, no deduction for labour and binding wire saved for not
providing lap length shall be made).
5.42.1/ Coupler for 16 mm diameter reinforcement bar. each 126.30
5.51.1
5.42.2/5.5 Coupler for 20 mm diameter reinforcement bar. each 171.60
1.2
5.42.3/ Coupler for 25 mm diameter reinforcement bar. each 237.80
5.51.3
5.42.4/ Coupler for 28 mm diameter reinforcement bar. each 328.10
5.51.4
5.42.5/ Coupler for 32 mm diameter reinforcement bar. each 381.20
5.51.5
5.43 Providing and fixing in position Stainless steel Grade 304 plate-1.0
mm thick as per design for expansion joints.
5.43.1/ 200 mm wide. metre 582.50
5.52.1
5.43.2/ 300 mm wide. metre 851.10
5.52.2
5.44 Providing and fixing of expansion joint system related with floor
location as per drawings and direction of Engineer-In-Charge. The
joints system will be of extruded aluminum base members, self
aligning / self centering arrangement and support plates etc. as per
ASTM B221-02. The system shall be such that it provides floor to floor
/floor to wall expansion control system for various vertical localtion in
load application areas that accommodates multi directional seismic
movement without stress to it's components. System shall consist of
metal profiles with a universal aluminum base member designed to
accommodate various project conditions and finish floor treatments.
The cover plate shall be designed of width and thickness required to
satisfy projects movement and loading requirements and secured to
base members by utilizing manufacturer’s pre-engineered self-
centering arrangement that freely rotates / moves in all directions. The
Self – centering arrangement shall exhibit circular sphere ends that
lock and slide inside the corresponding aluminum extrusion cavity to
allow freedom of movement and flexure in all directions including
vertical displacement. Provision of Moisture Barrier Membrane in the
Joint System to have watertight joint is mandatory requirement all as
per the manufactures design and as approved by Engineer -in-Charge
.(Material shall confirm to ASTM 6063).

5.44.1 Floor Joint of 100 mm gap. metre 6614.60

5.44.2 Floor Joint of 150 mm gap. metre 7270.70
5.44.3 Floor Joint of 200 mm gap. metre 7804.70

84 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
5.45 Providing and fixing of expansion joint system related with wall joint
(internal/external) location as per drawings and direction of Engineer-In-
Charge. The joints shall be of extruded aluminum base members, self
aligning / centering arrangement and support plates as per ASTM B221-
02. The material shall be such that it provides an Expansion Joints
System suitable for vertical wall to wall/ wall to corner application, both
new and existing construction in office Buildings & complexes with no
slipping down tendency amongst the components of the Joint System.
The Joint System shall utilize light weight aluminum profiles exhibiting
minimal exposed aluminum surfaces mechanically snap locking the
multicellular to facilitate movement. (Material shall confirm to ASTM
6063).
5.45.1 Wall Joint of 100 mm gap. metre 5271.80
5.45.2 Wall Joint of 150 mm gap. metre 5683.80
5.45.3 Wall Joint of 200 mm gap. metre 6095.70
5.46 Providing and fixing of expansion joint system of approved make and
manufactures for various roof locations as per approved drawings and
direction of Engineer-In-Charge. The joints shall be of extruded aluminum
base members with, self aligning and self centering arragement support
plates asper ASTM B221-02. The system shall be such that it provides
watertight roof to roof/roof to corner joint cover expansion control system
that is capable of accommodating multidirectional seismic movement
without stress to its components. System shall consist of metal profile that
incorporates a universal aluminum base member designed to
accommodate various project conditions and roof treatments. The cover
plate shall be designed of width and thickness required to satisfy
movement and loading requirements and secured to base members by
utilizing manufacturer’s preengineered self-centering arrangement that
freely rotates / moves in all directions.The Self centering arrangement
shall exhibit circular sphere ends that lock and slide inside the
corresponding aluminum extrusion cavity to allow freedom of movement
and flexure in all directions including vertical displacement. The Joint
System shall resists damage or deterioration from the impact of falling ice,
exposure to UV, airborne contaminants and occasional foot traffic from
maintenance personnel. Provision of Moisture Barrier Membrane in the
Joint System to have water tight joint is mandatory requirement. Material
shall confirm to ASTM 6063.
5.46.1 Roof Joint of 100 mm gap. metre 6614.60
5.46.2 Roof Joint of 150 mm gap. metre 7026.50
5.46.3 Roof Joint of 200 mm gap. metre 7316.50
5.47 Providing and fixing in position factory made precast RCC M-40 doors
and windows frames having excellent smooth finish as per IS: 6523 with
reinforcement of 3 Nos, 6 mm dia main bars tied with 3 mm M.S stirrups
placed @ 200 mm C/C and 6 numbers high strength polymer blocks of
required size for fixing hinges including providing 6 no specially designed
M.S. galvanised sleeves for accomodating 6 mm dia fully threaded bolts
for fixing hold fast on vertical members, providing suitable arrangement
for recieving sliding door bolts and tower bolt etc all complete, as per the
direction of Engineer in charge. (The cost of hold fast and cc block of
1:3:6 mix is also included in the item.) The frame shall be measured in
running meter correct to two places of decimal.

BCD/SOR_8th Edition_October 2016 85

Code
Description Unit Rate Rs.
No.
5.47.1 Door frame 125 mm x 60 mm. metre 421.50
5.47.2 Door frame 100 mm x 60 mm. metre 392.30
5.47.3 Door frame 85 mm x 60 mm. metre 377.30
5.48 Providing and laying Reinforced cement concrete for construction of
piers,abutments, portal frames, pier caps and bearing pedestals and
seismic arresters over pier/ abutment caps at all locations with
specified grade using Ordinary Portland Cement (conforming to
strength requirement of IS:8112) including the cost of steel centering
and shuttering etc. complete including testing of materials etc. for
casting pier & pier cap in one/two stage, necessary tools, plants,
machinery and all related operations as required to complete the
work as per drawings and Specifications with all leads, lifts and
depths true to level and position but excluding the cost of providing
reinforcement. Reinforcement shall be measured and paid
separately. Cement content considered in this item is 480 kg/cum.
Excess/less cement used as per design mix is payable/recoverable
separately.
5.48.1 Reinforced Cement Concrete M50. cum 5601.5
5.48.2 Reinforced Cement Concrete M60. cum 6910.2
5.48.3 Extra for using M50/M60 grade self-compacting Reinforced cum 612.8
Cement Concrete.
5.49 Constructing cast-in situ RCC diaphragm wall byproviding and laying
machine batched, machine mixed, self compacting, ready mix reinforced
cement concrete, tramie controlled, of M 30 grade using minimum 400 kg.
cement per cum of concrete including providing and mixing required
admixtures in recommended proportions as per IS : 9103, as approved by the
Engineer-in-charge, for achieving 150- 200mm slump, for diaphragm wall
having thickness as per approved structural design not exceeding 600 mm, in
pannels of required depth and lengths as per approved drawing, including
constructing necessary guide walls as required and as specified including
boring in all kinds of soils and rocks, including working in or under water and /
or liquid mud, in foul conditions and pumping or bailing out of water and
removing slush, including disposal of earth/ rock / slush etc. for all leads and
all lifts, including preparing, providing and re-circulating bentonite slurry in the
trench as and when required for all depths, including agitating bentonite slurry
during trenching etc., providing and fixing stop ends or form tubes, upto the
required depth of diaphragm wall including extracting the same after casting,
including chipping off the bentonite adulterated concrete or unsound concrete
up to the cut off level for obtaining the sound concrete, dressing undulations
on the exposed face of diaphragm wall after excavation by chipping / chiseling
etc. including filling the depression/ cavities with sound concrete etc.
complete and as directed by the Engineer-in-charge, including providing
recess for bearing plates and fixing insert boxes for inclined rock anchors etc.
complete as per the specifications and approveddesign and as directed by the
Engineer-in- charge, .but excluding the cost of reinforcement and inserts.
(rates include cost of all inputs of labour, material and T & P, cost of handling,
lifting & placing in position the reinforcement cage in the trench, including the
additional cost of welding the reinforcement bars etc. involved in the work and
all other incidental expenditure for completing the work as directed by the
Engineer-in-charge), However, the actual area of the diaphragm wall, correct
to two places of decimal, from design bottom level to the design cut off level
(including portion anchored in the rock upto the design bottom level) only shall
be measured for payment.
5.49.1 Excess/less cement used for design mix including the extra cum 11756.1
cement required for under water concreting is payable /
recoverable separately.
86 BCD/SOR_8th Edition_October 2016
SUB HEAD : 6.0
BRICK WORK
 BUILDING WORK - Contd.

6.0 Brick Work (A)

Code
Description Unit Rate Rs.
No.
6.1A Brick work with bricks of class designation 100A in foundations
and plinth in :
6.1.12/1 Cement mortar 1 .:4 (1 cement: 4 coarse sand ) cum 4724.40
6.1.14A Cement mortar 1:6 (1 cement: 6 coarse sand ) cum 4490.60
6.3A Extra for Brick work in superstructure above plinth level upto floor cum 513.30
V cum
6.4A Extra for brick work in superstructure above floor V level for each cum 383.60
four floors or part thereof.
6.11A Extra for forming cavity 5cm to 7.5cm wide in cavity wall with sqm 76.60
necessary weep and vent holes including use of cores and cast
of providing and fixing bitumansttc coted m.s. toles 300mmlong of
25mmx3mmsection at not less than 3 tiles per sqm as per
approved design.
6.12A Providing half brick masonry with bricks of class designation per m 165.30
100A in cement mortar 1:3 (1 cement: 3 coarse sand ) in
supersturcture for closing cavity 5 to 7.5 cm wide in cavity wall
complete with 10cmm/11.4cm wide bitumen felt type 3 grade 1.
6.13A Brick work 7cm thick with brick of class designation 100A cement sqm 426.60
mortar 1:3 (1 cement: 3 coarse sand) in super structure
6.15A Brick work in plain arches in superstructure including centring and cum 7164.70
shuttering complete for span upto 6 metres with bricks of class
designation 100A in cement mortar 1:3(1 cement:3 coarse sand )

6.16A Brick work in gauged arches in superstructure in cement mortar cum 8370.40
1:3 (1 cement:3 coarse sand) including centring and shutierning
complete. Span upto 6 metres with
6.17A Extra for additionaLcost of centring for arches exceeding 6 sqm 267.40
mspan including all shuttering , Bolting , wedging and
removaL(Area of the soffit to be measured ).
6.18A Half brick masonry with bricks of class designation 100A in
foundations and plinth in :
6.18.3A Cement mortar 1:3 (1 cement: 3 coarse sand) sqm 581.30
6.18.4A Cement mortar 1:4 (1 cement: 4 coarse send) sqm 555.10
6.19A Extra for half Brick masonry in superstructure above pinth level sqm 53.30
upto floor V level.
6.20A Extra for half brick masonry in superstructure. Above floor V level sqm 43.80
for every four floors or part there of
6.21A Extra for providing and placing in position 2 Nos, 6 mm dia , MS sqm 55.40
bars at every third course of half brick masonry (with F. P. S.
bricks)
6.23A Tile brick masonry with tile bricks of class desgnation 100 in
foundation and plinth in :
6.23.7A Cement mortar 1:4 (1 cement :4 coarse sand) cum 8373.20
6.23.8A Cement mortar 1.6 (1 cement :6 coarse sand) cum 7999.20

87 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
6.24A Extra for tile bricks masonry with tile bricks of class designation cum 506.20
10OA in superstructure fromplinth leveLupto floor five level.
6.25A Extra for tile brick masonry with tile bricks of class designation cum 383.60
100A in superstructure above floor five level for every four floor or
part thereof,
6.29A Tile brick masonry with bricks of class desigation 100 in plain cum 10555.10
arch work superstructure in cement mortar 1:4 (1 cement: 4 co
6.30A Tte brick masonary with tile bricks ot class designation 100A in cum 11623.60
gauded arch work in superstucture in cement mortar 1:4 (1
cement: 4 coarse sand) including centring and shuttering
complete.
6.31A Tile brick masonry work 5 cm thick with tile bricks of class sqm 479.00
designation 100A in cement mortar 1:3 (1 cement: 3 coarse
sand) in superstructure .
6.32 A Honey- comb brick work 10/11.4 cm thick with bricks of class sqm 384.80
designation 100A in cement mortar 1:4 (1 cement: 4 coarse sand)
6.39A Extra for brick work in under water mud or liquid mud including cum 293.00
cost of pumping or bailing out water - slush etc
6.41A Brick work with selected bricks of class designation 100A in cum 4556.70
exposed brick work including making horizontal and vertical
irooves 10mm wide 12mm deep complete from ground level up to
plinth level in cement mortars 1:6(1 cement: 6 corse sand)
6.45A Extra for exprosed brick work in superstructure above plinth level cum 645.80
and upto floor level. 0.75 x 1.5 = 1.13
6.47A Providing 250mm wide brick drain in cement mortar (1:6) with av. Per m 970.50
150mm. Clear depth and 250mm apron including cost of E/W.
involved with 75mm cement concrete (1:4:8) over one brick
designation 100-A flat soling in proper grade and slope at the
base.the drain duly.plastered in CM. (1:3) with punning over
exposed surface all complete as per building specification and
6.48A Providing 150mm wide brick drain in cement mortar (1:6) with av. Per m 512.80
150mm clear depth and 125mm apron concrete (1: 4:8), over one
brick designation 100-A flat soling in proper grade and slope at
the base, the drain duly plastered in CM. (1:3) with punning over
exposed surface all complete as per building specification and
6.38 Providing and laying autoclaved aerated cement blocks masonry cum 4870.60
with 100 mm thick AAC blocks in super structure above plinth
level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse
sand).The rate includes providing and placing in position 2 Nos 6
mm dia M.S. bars at every third course of masonry work.
6.4 Providing and laying Gypsum panel partitions 100 mm thick with sqm 797.10
water proof Gypsum panels of size 666x500x100 mm, made of
calcite phosphor Gypsum fixed with tongue and groove, jointed
with bonding plaster as per manufacturers specifications in
superstructure above plinth level up to floor V level. Gypsum
6.41 Extra for Gypsum panel partitions in superstructure above floor V sqm 44.20
level for every four floors or part there of.

BCD/SOR_8th Edition_October 2016 88

 6.0 Brick Work (B)
Code
Description Unit Rate Rs.
No.
6.1B Brick work with bricks of class designation 100B in foundations
and plinth in :
6.1.12B Cement mortar 1.:4 (1 cement: 4 coarse sand ) cum 4440.50
6.1.14B Cement mortar 1:6 (1 cement: 6 coarse sand ) cum 4206.70
6.3B Extra tor Brick work in superstructure above plinth level upto floor cum 484.80
V cum
6.4B Extra for brick work in superstructure above floor V level for each cum 383.60
four floors or part thereof.
6.11B Extra for forming cavity 5cm to 7.5cm wide in cavity wall with sqm 74.30
necessary weep and vent holes including use of cores and cast
of providing and fixing bitumanstic coted m.s. toles 300mm long
of 25mm x 3mm section at not less than 3 tiles per sqm as per
approved design.
6.12B Providing half brick masonry with bricks of class designation m 165.30
100B in cement mortar 1:3 (1 cement: 3 coarse sand ) in
supersturcture for closing cavity 5 to 7.5 cm wide bitumen felt
6.13B Brick work 7cm thick with brick of class designation 100B cement sqm 404.40
mortar 1:3 (1 cement: 3 coarse sand) in super structure
6.15B Brick work in plain arches in superstructure including centring and cum 6856.90
shuttering complete for span upto 6 metres with bricks of class
designation 100B in cement mortar 1:3(1 cement: 3 coarse sand
6.16B )Brick work in gauged arches in superstructure in cement mortar cum 8037.40
1:3 (1 cement:3 coarse sand) including centring and shutterning
complete. Span upto 6 metres with
6.17B Extra for additionaLcost of centring for arches exceeding 6 sqm 267.40
mspan ' including alLshuttering . Bolting , wedging and
removai_(Area of the soffit to be measured ).
6.18B Half brick masonry with bricks of class designation 100B in
foundations and plinth in :
6.18.3B Cement mortar 1:3 (1 cement: 3 coarse sand ) sqm 547.50
6.18.4B Cement mortar 1:4(1 cement: 4 coarse send ) sqm 521.30
6.19B Extra for half Brick masonry in superstructure above pinth level sqm 53.30
upto floor V level.
6.20B Extra for half brick masonry in supersrructure. Above floor V level sqm 43.80
for every four floors or part there of
6.21B Extra for providing and placing in position 2 Nos, 6 mm dia , MS sqm 55.20
bars at every third course of half brick masonry (with F. P. S.
6.23B Tile brick masonry with tile bricks of class desgnation 100 in
foundation and plinth in :
6.23.7B Cement mortar 1:4 (1 cement :4 coarse sand) cum 8367.50
6.23.8B Cement mortar 1.6 (1 cement :6 coarse sand) cum 7993.40

89 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
6.24B Extra for tile bricks masonry with tile bricks of class designation cum 506.20
100B in superstructure fromplinth feve! upto floor five level.
6.25B Extra for tile brick masonry with tile bricks of class designation cum 383.60
100B in superstructure above floor five level for every four floor or
part thereof.
6.29B Tile brick masonry with bricks of class desigation 100 in plain cum 10542.40
arch work superstructure in cement mortar 1 ;4 (1 cement: 4
coarse sand ) including centring and shuttering complete.
6.30B Tie brick masonary with tile bricks of class designation 100B in cum 11634.80
gaudecf arch work in superstucture in cement mortar 1:4 ( 1
cement: 4 coarse sand ) including centring and shuttering
6.31B Tile brick masonry work 5 cm thick with tile bricks of class sqm 473.30
designation 100B in cement mortar 1:3 (1 cement: 3 coarse sand
) in superstructure ,
6.32B Honey- comb brick work 10/11.4 cm thick with bricks of class sqm 358.50
designation 100B in cement mortar 1:4 (1 cement: 4 coarse sand
)
6.39B Extra for brick work in or under water mud or liquid mud including cum 293.00
cost of pumping or bailing out water — slush etc
6.41 B Brick work with selected bricks of class designation 100B in cum 4255.50
exposed brick work including making horizontal and vertical
grooves 10mm wide 12mm deep complete from ground level up
to plinth level in cement mortars 1:6(1 cement: 6 corse sand)
6.45B Extra for exprosed brick work in superstructure above plinth level cum 624.96
and upto floor level. 0.75 x 1.5 = 1.13

6.0 FLY ASH Brick Work (C)

6.1C Brick work with fly ash bricks as per IS 12894(2002) & IS
3495 in foundations and plinth in :
6.1.12C Cement mortar 1.:4 (1 cement: 4 coarse sand ) cum 4936.30
6.1.14C Cement mortar 1:6 (1 cement: 6 coarse sand ) cum 4706.00
6.3C Extra tor Brick work in superstructure above plinth level upto floor cum 513.30
V cum
6.4C Extra for brick work in superstructure above floor V level for each cum 383.60
four floors or part thereof.

6.0 Brick Work with Lime Mortar (D)

6.1D Brick work with bricks of class designation 100A in
foundations and plinth in :
6.1.12D Lime mortar (1:1:1) (1 limeputty: 1shukhi:1coarse sand ) cum 4644.40
6.1.14D lime mortar mortar 1:1:2(1 limeputty: 1 surkhi:2 coarse sand cum 4511.60
) Details of cost for 1 cum

BCD/SOR_8th Edition_October 2016 90

SUB HEAD : 7.0
STONE WORK
 BUILDING WORK - Contd.

7.0 Stone Work

Code
Description Unit Rate Rs.
No.
A7.1 Dressing of sand stone for ashlar cyclopean- 10cudm 47.20
A7.2 Dressing of sand stone for moulded work 10cudm 97.80
A7.3 Dressing of sand stone for ashlar puncheol ordinary work 10cudm 40.03
A7.4 Dressing of sand stone m arch dome's or circular moulded work 10cudm 118.20
A7.5 Dressing of sand stone for ashlar moulded and currved colonic 10cudm 160.60
A7.6 Dressing of sand stone ------ sqm 465.40
A7.7 Fixing charges for stone work including pointing 10cudm 50.90
A7.8 Fixing charges for stone in veneer work . sqm 582.40
7.1 Random rubble masonry with hard stone in fourdation and plinth
including leveling up with cement concrete 1:6:12 (1 cement: 6
coarse sand : 12 graded stone aggregate 20 mm nominal size )
at plinth level with .
7.1.1 Cement mortar 1:6 (1 cement: 6 coarse sand ) cum 2643.20
7.2 Extra for random rubble masonry with hard stone in
spuerstructure above plinth level and upto floor five level,
including leveling up with cement concreter 1:6:12 ( 1 cement: 6
coarse sand : 12 graded . stone aggregate 20 mm nomiinal size )
at window sills , ceiling level and the like. cum 521.70
7.3 Extra for random rubble masonry with hard stone in
superstructure above floor V levei for every four floors or part
therof . cum 483.30
7.4 Extra for random rubble masonry with hard stone in .
7.4.1 Square or rectangular pillars cum 238.50
7.4.2 Circular pillars cum 752.10
7.5 Extra for random rubble masonry with hard stone curved on
plan for ad mean radius not exceeding 6 m . cum 299.90
7.6 Coursed rubble masonry (fist sort) with hard stone in foundation
and plinth with .
7.6.1 Cement mortar 1:6(1 cement: 6 coarse sand ) cum 3021.50
7.7 Coursed rubble masonry (second sort) with hard stone in
foundation & plinth with >
7.7.1 Cement mortar 1:6 (1 cement: 6 coarse sand ) cum 2822.40
7.8 Extra for coursed rubble masonry with hard stone (first or
second sort) in superstructue above plinth level and upto floor
five level . cum 594.10
7.9 Extra for coursed rubble masonry with hard stone (first or
second sort} in superstructure above floor V level for every four
floor's or part thereof. cum 483.30
7.10 Extra for coursed rubble masonry with hard stone (first or
second sort) in :
7.10.1 Square or rectangular pillars cum 264.80
7.10.2 Circular pillars cum 850.80

91 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
7.11 Extra for coursed rubble masnory with hard stone (first or second
sort) curved on plan for a mean radius not exceeding 6 m . cum 325.90
7.12 Stone work in plain ashlar in super structure upto floor five level
in cement mortar 1:6{1 cement: 6 coarse sand ) including
pointing with cement mortar 1 2 (1 white cement: 2 stone dust)
with an admixture of pigment matching the stone shade .
7.12.1 Red sand stone cum 22469.20
7.12.2 White sand stone cum 22900.40
7.13 Stone work plain ashlar in arches in cement mortar 1:3 (1
cement: 3 coarse sand ) including centring, shuttering and
pointing with white cement mortar 1:2(1 white cement: 2 stone
dust) with an admixture of pigment matching the stone shade .
7.13.1 Red sand stone cum 25237.10
7.13.2 White sand stone cum 24612.40
7.14 Stone work plain ashlar in domes in cement mortar 1:3 {1
cement: 3 coarse sand ) including centring, shuttering and
pointing with white cement mortar 1:2(1 white cement: 2 stone
dust} with an admixture of pigment matching the stone shade .
7.14.1 Red sand stone cum 33690.60
7.14.2 White sand stone cum 34455.80
7.15 Stone work ashlar punched (ordinary} in superstructure upto floor
five level in cement mortar 1:6(1 white cement: 6 coarse sand )
including pointing with cement mortar 1:2(1 cement: 2 stone
dust) with an admixture of pigment matching the stone shade . '
7.15.1 Red sand stone cum 21360.60
7.15.2 White sand stone cum 23469.70
7.16 Extra for stone work , plain ashlar or ashiar punched above floor
V for every four floors or part thereof. cum 482.70
7.17 Extra for plain ashiar or ashiar punched in :
7.17.1 Square or rectangular pillars cum 711.40
7.19 Extra for additional cost of centing for arches exceeding 6m span
including all strutting , bolting, wedging etc , and removal (area of
soffit to be measured). sqm 267.40
7.2 Stone work sunk or moulded or sunk and moulded upto floor five
level in cement mortar 1:6 (1 cement: 6 coarse sand ) inculding
pointing with white cement mortar 1:2 (1 cement: 2 stone dust)
with an admixture of pigment matching the stone shade:
7.20.1 Red sand stone cum 30877.70
7.20.2 White sand stone cum 34284.50
7.21 Extra for stone work sunk or moulded or sunk and moulded or
carved in :
7.21.1 Triangular or Square or rectangular pillars cum 2412.60
7.21.2 Circular or polygonal pillars cum 6835.60

BCD/SOR_8th Edition_October 2016 92

Code
Description Unit Rate Rs.
No.
7.22 Extra for stone work sunk or moulded in cornices . metre 14.50
per cm
7.23 Stone work (machine cut edge) for wall lining etc. (veneer work )
over 12 mm thick bed of cement lime mortar 1:1:6 (1 cement: 1
lime putty : 6 fine sand ) including pointing in white cement
mortar 1:2(1 white cement: 2 stone dust) with an admixture of
pigment matching the stone shade: (To be secured to the
backing by means of cramps which shall be paid for seperately)
7.23.1 Red sand stone- exposed face fine dressed with rough
backing
7.23.1.1 70 mm thick 0.1 sqm 2022.70
7.23.1.2 60 mm thick 0.1sqm 1917.10
7.23.1.3 50 mm thick 0.1 sqm 1811.70
7.23.1.4 40 mm thick 0.1 sqm 1705.70
7.23.2 White sand stone
7.23.2.1 70 mm thick 0.1sqm 2079.60
7.23.2.2 60 mm thick 0.1sqm 1965.80
7.23.2.3 50 mm thick 0.1sqm 1852.30
7.23.2.4 40 mm thick 0.1sqm 1738.00
7.24 Extra for stone work (veneer work ) curved on plan with a mean cum 1853.30
radius not exceeding 6 m .
7.25 Providing and fixing gun metal cramps of required shape for
anchoring stone wall lining to the backing or securing adjacent
stones in stone wall lining in cement mortar 1:2 (1 cement: 2 fine
sand) including making the necessary chases.
7.25.1 25x6 mm - 30 long each 107.20
cramp
7.26 Providing and fixing stone dowels 10x5x2.50 cm cut to double dowel 35.20
wedge shape as per design in cement mortar 1:2 (1 cement: 2
fine sand ) including making the necessary chases .
7.27 Providing and fixing copper pins 7.5 cm long 6 mm diameter for copper 25.80
securing adjacent stones in stone wall lining in cement mortar 1:2 pin
(1 cement: 2 fine sand ) including making the necessary chases .

7.29 Providing and fixing horizontal chajja of stone 400 mm thick and
upto 80 cm projection in cement mortar 1:4(1 cement: 4 coarse
sand) including pointing in white cement mortar 1:2 (1 white
cement: 2 stone dust) with an admixture of pigment matching the
stone shade.
7.29.1 Red sand stone sqm 610.90
7.29.2 White sand stone sqm 641.50
7.30 30 mm red sand stone sun-shade (chisel-dressed) supported on sqm 678.70
red sand stone brackets, fixed in walls with cement mortar 1:4 (1
cement: 4 coarse sand ) including finishing complete.

93 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
7.31 Providing and fixing red sand stone brackets 55x22.5x45 cm
sunk and moulded including providing and fixing with 4 Nos. gun
metal cramp 25x6 mm. 30 cm long and dowel bars 7.5 cm long 6
mm dia as per design. bracket 2228.60
7.32 Stone work , plain in copings , cornices, string courses and plinth
courses, in cement mortar 1: 6 (1 cement: 6 coarse sand )
including pointing with white cement mortar 1:2 (1 white cement:
2 stone dust) with an admixture of pigment matching the stone
shade .
7.32.1 Red sand stone cum 29634.80
7.32.2 White sand stone cum 30066.10
7.38 Providing and fixing stone jaii 40 mm thick throghout(without
sunking or moulding in jali slab) in cement mortar 1:3(1 cement:
3 coarse sand ) including pointing in white cement mortar 1:2 (1
white cement: 2 stone dust) with an admixture of pigment,
matching the stone shade, jali slab without any chamfers etc.
7.38.1 Red sand stone sqm 6125.40
7.38.2 White sand stone sqm 6152.20
7.36 Wall lining butch work with Dholpur stone 40 mm thick rough
taching on the exppsed surface with stone strips of minimum
length 230 mm and required with including embedding every
lenth layer and bottom most layer in masonry or concrete after
making necessary chases of size 75 x 75 mm and by providing
layer or 75 mm thick strips i/c 12 mm thick bed of cement mortar
1:3 (1 cement: 3 coarse sand ) i/c ruled pointing in cement mortar
1:2 (1 white cement: 2 stone dust) with an admixture of pigment
to match the shade of stone complete as per direction of sqm 1311.70
7.37 Stone work ( machine cut edges veneer work) for wall lining upto
10 m height, backing filled with a grout of 12 mm thick cement
mortar 1:3 (1 Cement : 3 coarse sand) and jointed with Cement
mortar 1:2 (1 cement : 2 stone dust), including rubbing and
polishing complete. (To be secured to the backing and the sides
by means of cramps and pins which shall be paid for separately)
7.37.1 Kota stone slabs exposed face dressed and rubbed.
7.37.1.1 25 mm thick sqm 1227.00
7.37.1.A Dressing of sand stone in veneer work sqm 1697.00
7.37.1.B Dressing of sand stone in ashlar punched
(ordinary work ) sqm 1265.10
7.38 Stone tile work for wall lining upto 10.0m height with special
adhesive like araldite or equivalent over 12 mm thick bed of
cement mortar 1:3 (1 cement: 3 coarse sand ) including pointing
in-white cement with an admixture of pigment to match the stone
7.38.1 8 mm thick (mirror polished and machine cut edge )
7.38.1.1 Granite black stone sqm 1498.80
7.38.1.2 Raj Nagar plain white marble / Udaipur green marble /
Zebra black marbleGranite black stone sqm 1248.90

BCD/SOR_8th Edition_October 2016 94

Code
Description Unit Rate Rs.
No.
7.39 Extra for stone work for wall lining on exterior walls of sqm 71.50
height more than 10 m from ground level for every additional
height of 3 m or part there of.
7.40 Providing and fixing dry cladding upto 10 metre heights with
30 mm thick gang saw cut stone with (machine cut edges) of
uniform colour and size upto 1mx1m, fixed to structural
steel frame work and / or with the help of cramps, pins etc.
and sealing the joints with approved weather sealant as per
Architectural drawing and direction of Engineer-in-Charge.
(The steel frame work, stainless steel cramps and pins etc.
shall be paid for separately.)
7.40.1 Red sand stone sqm 2124.40
7.40.2 White sand stone sqm 2159.80
7.41 Providing and fixing structural steel frame (for dry cladding Per Kg 119.40
with 30 mm thick gang saw cut with machine cut edges sand
stone) on walls at all heights using M.S. square / rectangular
tube in the required pattern as per architectural drawing,
including cost of cutting, bending, welding etc. The frame
work shall be fixed to the wall with the help of MS brackets /
lugs of angle iron / flats etc. which shall be welded to the
frame and embedded in brick wall with cement concrete
block 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) of size 300x230x300 mm,
including cost of necessary centring and shuttering and with
approved expansion hold fasteners on CC/RCC surface,
including drilling necessary holes. Approved cramps / pins
etc. shall be welded to the frame work to support stone
cladding, the steel work will be given a priming coat of Zinc
primer as approved by Engineer-in-Charge and painted with
two or more coats of epoxy paint (Shop drawings shall be
submitted by the contractor to the Engineer-in-Charge for
approval before execution). The frame work shall be fixed in
true horizontal & vertical lines/planes. (Only structural steel
frame work shall be measured for the purpose of payment,
stainless steel cramps shall be paid for separately and
nothing extra shall be paid.)
7.42 Providing and fixing adjustable stainless steel cramps of Each 177.20
approved quality, required shape and size,adjustable with
stainless steel nuts, bolts and washer (total weight not less
than 260 gms), for dry stone cladding fixed on frame work at
suitable location, including making necessary recesses in
stone slab, drilling required holes etc complete as per
direction of the Engineer-in-charge.

95 BCD/SOR_8th Edition_October 2016

SUB HEAD : 8.0
MARBLE WORK
 BUILDING WORK - Contd.

8.0 Marble Work

Code
Description Unit Rate Rs.
No.
A8.1 Dressing of Marble for steps, jambs, walls, pillars and other plain 10cudm 153.40
work
A8.2 Dressing of marble for moulded jambs and heads, straight 10cudm 244.40
mouldings and plain arces or domes.
A8.3 Dressing of marble in moulded arches or domes and cirular 10cudm 525.40
mouldings.
A8.4 Dressing of marble veneer work sqm 671.20
A8.5 Labour for fixing marble in veneer work 2.5 cm to 5 cm thick. sqm 972.20
8.1 Marble work gang saw cut (polished and machine cut) of thickness
18mm for wall lining (veneer work) in c ement mortar 1:3 (1
cement :3 coarse sand) including pointing with white coment
mortar 1:2(1 shite cement:2 marble dust) with an admixture of
pigment to match the marble shade:(To be secured to the backing
by means of cramps, which shall be paid for separately)
8.1.1 White Marble-Raj Nagar Plain/Udaipur green marble/
Zebra block marble
8.1.1.1 Area of slab upto 0.50 sqm sqm 2196.10
8.1.1.2 Area of slab over 0.50 sqm sqm 2337.20
8.2 Providing and fixing 18 mm thick gang saw cut, mirror
polished, premoulded and prepolished, machine cut for
kitchen platforms, vanity counters, window sills, facias and
similar locations, of required size,approved shade, colour and
texture laid over 20 mm thick base cement mortar 1:4 (1
cement : 4coarse sand), joints treated with white cement,
mixed with matching pigment, epoxy touch ups,including
rubbing, curing, moulding and polishing to edges to give high
gloss finish etc. complete at all levels.
8.2.1 Rajnagar plain white marble /Udaipur green marble/
Zebra block marble
8.2.1.1 Area of slab upto 0.50 sqm sqm 1923.90
8.2.1.2 Area of slab over 0.50 sqm sqm 2052.00
8.2.2 Granite of any colour and shade
8.2.2.1 Area of slab upto 0.50 sqm sqm 3539.50
8.2.2.2 Area of slab over 0.50 sqm sqm 3573.70
8.3 Providing edge moulding to 18 mm thick marble stone
counters, vanities etc., including machine polishing to edge
to give high gloss finish etc. complete as per design
approved by Engineer-in-Charge.
8.3.1 Marble work m 108.40
8.3.2 Granite work m 182.10

96 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
8.4 Extra for fixing marble/granite stone over and above m 181.50
coresponding basic item, in facia and drops of width upto 150
mm with expoxy resin based (Araldite or equivalent) adhesive
including cleaning etc. complete.
8.5 Extra for providing opening of required size & shape for wash Each 259.20
basins/kitchen sink in kitchen platform. Vanity counters and
similar location in marble/granite/stone work including
necessary holes for pillar taps etc. including
rubbing,moulding and polishing of cut edges etc. complete.
8.6 Mirror polishing on marble work/stone work where ever sqm 155.20
required to give high gloss finish complete.
8.7 Providing and fixing cramps of required size & shape in RCC/
CC / Brick masonry backing with cement mortar 1:2 ( 1
cement :2 coarse sand), including drilling necessary hole in
stones and embedding the cramp in the hole (fastener to be
paid separately).
8.7.1 Gunmetal cramps Per Kg 565.80
8.7.2 Stainless steel cramps Per Kg 594.10
8.8 Providing and fixing expansion hold fasteners on CC/R.C.C.
surface backing including drilling necessary holes and the
cost of bolt etc complete.
8.8.1 wedge expansion type
8.8.1.1 Fastner with-threaded dia. 1/4" or 6mm Each 25.10
8.8.1.2 Fashtner with threaded dia. 3/8" or 10 mm Each 26.70
8.8.1.3 Fastner with threaded dia. 1/2" or 12mm Each 43.00
8.9 Stone tile (polished) work for wall lining over 12 mm thick bed
of cement mortar 1:3 (1 cement : 3 coarse sand) and cement
slurry @ 3.3 kg/ sqm including pointing in white cement
complete.
8.9.1 8 mm thick
8.9.1.1 Raj nagar plain white marble / Udaipur green marble sqm 1199.00
/ Zebra black marble
8.9.1.2 Granite of any colour and shade sqm 1624.40
8.10 Providing and fixing stone slab with table rubbed, edges
rounded and polished, of size 75x50 cm deep and 1.8 cm
thick, fixed in urinal partitions by cutting a chase of
appropriate width with chase cutter and embedding the stone
in the chase with epoxy grout or with cement concrete 1:2:4
(1 cement : 2 coarse sand : 4 graded stone finished
smooth.aggregate 6 mm nominal size) as per direction of
Engineer-in-Charge and
8.10.1 White Agaria Marble Stone sqm 3038.70
8.10.2 Granite Stone of approved shade sqm 3112.0

BCD/SOR_8th Edition_October 2016 97

Code
Description Unit Rate Rs.
No.
8.11 Providing and fixing machine cut, mirror / eggshell polished ,
Marble stone work for wall lining (veneer work) including
dado, skirting, risers of steps etc., in required design and
pattern wherever required,stones of different finished surface
texture, on 12 mm (average) thick cement mortar 1:3 (1
cement :3 coarse sand) laid and jointed with white cement
slurry @ 3.3 kg/sqm including pointing with white cement
slurry admixed with pigment of matching shade, including
rubbing, curing, polishing etc. all complete as per
Architectural drawings, and as directed by the Engineer-in-
Charge.
(a.) 18 mm thick Italian Marble stone slab,Perlato, Rosso sqm 6251.70
verona, Fire Red or Dark Emperadore etc.
8.12 Providing and laying flamed finish Granite stone flooring in
required design and patterns, in linear as well as curvilinear
portions of the building all complete as per the architectural
drawings with 18 mm thick stone slab over 20mm(avearage)
thick base of cement mortar 1:4(1 cement : 4 coarse sand)
laid and jointed with cement slurry and pointing with white
cement slurry admixed with pigment of matching shade
including rubbing , curing and polishing etc. all complete as
specified and as directed by the Engineer-in-Charge :

a.) Flamed finish granite stone slab Jet Black, Cherry sqm 2808.30
Red, Elite Brown, Cat Eye or equivalent.

98 BCD/SOR_8th Edition_October 2016

SUB HEAD : 9.0
WOOD WORK
 BUILDING WORK - Contd.

9.0 Wood Work

Code
Description Unit Rate Rs.
No.
9.1 Providing wood work in frames of doors, windows, clerestory windows
and other frames, wrought framed and fixed in position with hold fast
lugs or with dash fasteners of required dia & length ( hold fast lugs or
dash fastener shall be paid for separately).
9.1.1 Second class teak wood cum 91504.80
9.1.2 Sal wood cum 73465.50
9.1.3 Kiln seasoned and chemically treated hollock wood. cum 49794.40
9.1.4 Local wood cum 47639.70
9.2 Providing laminated veneer lumber conforming to IS:14616 and TAD -
15: 2001( Part B) in factory made frames of doors, windows,
clerestory windows and other frames, wrought framed and fixing in
cum 96269.70
position with hold fast lugs or with dash fasteners of required dia &
length ( hold fast lugs or dash fastener shall be paid for separately).

9.3 Providing wood work in frames of false ceiling, partitions etc. sawn
and fixed in position :
9.3.1 Sal wood cum 70771.60
9.3.2 Kiln seasoned and chemically treated hollock wood. cum 46936.80
9.4 Extra for additional labour for cirular works,such as in frames of fan
light.
9.4.1 Second Class teakwood- cum 9135.40
9.4.2 Sal wood- cum 7331.50
9.4.3 Klin seasoned and and chemically treated hollock wood. cum 4964.50
9.5 Providing and fixing panelled or panelled and glazed shutters for
doors, windows and clerestory windows, including ISI marked
M.S.pressed butt hinges bright finished of required size with
necessery screws, excluding panelling which will be paid for
separately, all complete as per direction of Engineerin-charge.
9.5.1 Second Class teak wood-
9.5.1.1 35 mm thick sqm 2505.80
9.5.1.2 30 mm thick sqm 2219.00
9.5.2 Kiln seasoned and chemically treated hollock wood.
9.5.2.1 35 mm thick sqm 1512.40
9.5.2.2 30 mm thick sqm 1363.10
9.5.3 Kiln seasoned selected planks of sheesham wood.
9.5.3.1 35 mm thick sqm 2310.70
9.5.3.2 30 mm thick sqm 2035.20
9.6 Providing and fixing 35 mm thick factory made laminated veneer
lumber door shutter conforming to IS : 14616 and TADS 15:2001
(Part B), including ISI marked M.S.pressed butt hinges bright finished
of required size with necessery screws, all complete as per directions
of Engineer-in-Charge and panelling with panels of:

99 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.6.1 12 mm thick plain grade - 1, medium density flat pressed
three layer particle board FPT - I or graded wood particle
board FPT-I, IS :3087 marked, bonded with BWP type sqm 2484.70
synthetic resin adhesive as per IS : 848:
9.6.2 12 mm thick pre-laminated particle board (decorative
lamination on both sides) grade - 1, medium density flat
pressed, three layer particle board FPT - I or graded wood
particle board FPT - I, conforming to IS : 3087, bonded sqm 2704.40
with BWP type synthetic resin adhesive as per IS : 848
and prelaminated conforming to IS : 12823, Grade 1,
Type - II marked :
9.6.3 12 mm thick prelaminated (with decorative lamination on
one side and balancing lamination on other side) particle
board Grade -1 medium density flat pressed, three layer
sqm 2606.80
and graded (FPT-1) conforming to IS :3087 bonded with
BWP type synthetic resin adhesive as per IS :848 and
prelamination conforming to IS :12823 Grade-1 Type II
9.7 Providing and fixing panelling or panelling and glazing in panelled or
panelled and glazed shutters for doors, windows and clerestory
windows (Area of opening for panel inserts excluding portion inside
grooves or rebates to be measured). Panelling for panelled or
panelled and glazed shutters 25 mm to 40 mm thick:
9.7.1 Second class teak wood sqm 2029.10
9.7.2 Klin seasoned and chemically treated hollock wood
sqm 1227.60
for 40,35,30,25mm thick shutters
9.7.3 Ply wood 5 ply, 9 mm thick.
9.7.3.1 Decorative plywood both side decorative veneer (Type - I)
sqm 1826.20
conforming to IS 1328 BWR type.
9.7.3.2 Decorative plywood one side decorative veneer and
commercial veneer on other face (Type 1) conforming to IS sqm 1545.10
1328 BWR Type
9.7.4 Ply wood 7 ply, 9 mm thick.
9.7.4.1 Decorative plywood one side decorative veneer and
sqm 1663.50
commercial veneer on other face (Type 1) conforming to IS
9.7.5 Particle Board 12 mm thick.
9.7.5.1 Plain particle board flat pressed, 3 layer or graded wood
sqm 783.10
particle board medium density Grade I, IS : 3087 marked
9.7.5.2 Veneered flat pressed three layer or graded wood particle
board with commercial veneering on both sides conforming sqm 1042.00
to IS :3097, grade I
9.7.5.3 Pre-laminated particle board with decorative lamination on
one side and balancing lamination on other side, Grade I, sqm 1397.10
Type II, IS : 12823 marked
9.7.5.4 Pre-laminated particle board with decorative lamination on
sqm 1456.30
both sides, Grade I, Type II, IS :12823 marked
9.7.6 Coir Veneer Board (conforming to IS 14842 )
9.7.6.1 12 mm thick. sqm 1264.00

BCD/SOR_8th Edition_October 2016 100

Code
Description Unit Rate Rs.
No.
9.7.7 Float glass panes.
9.7.7.1 4 mm thick glass pane. sqm 943.00
9.7.7.2 5.5 mm thick glass pane. sqm 1194.50
9.7.8 Fly proof stainless steel grade 304 wire gauge with 0.5 mm
dia wire and 1.4 mm wide aperture with matching wood sqm 1499.90
beading
9.9 Providing and fixing glazed shutters for doors, windows and
clerestory windows using 4 mm thick float glass panes including ISI
marked M.S. pressed butt hinges bright finished of required size with
necessary screws.
9.9.1 Second class teak wood
9.9.1.1 35 mm thick sqm 3064.00
9.9.1.2 30 mm thick sqm 2736.30
9.9.2 Kiln seasoned and chemically treated hollock wood
9.9.2.1 35 mm thick sqm 1933.00
9.9.2.2 30 mm thick sqm 1762.50
9.9.3 Kiln seasoned selected planks of sheesham wood
9.9.3.1 35 mm thick sqm 2842.10
9.9.3.2 30 mm thick sqm 2545.00
9.10 Providing and fixing factory made laminated veneer lumber glazed
shutter conforming to IS: 14616 and TADS 15:2001 (Part B), using 4
mm thick float glass panes for doors, windows and clerestory
windows, including ISI marked M.S. pressed butt hinges bright
finished of required size with necessary screws, all as per directions
of Engineer-in-charge.
9.10.1 30 mm thick shutters sqm 2240.60
9.11 Extra for providing heavy sheet float glass panes instead of ordinary
float glass in glazed doors,windows and clerestory window shutters.
(Area of opening for glass panes excluding portion inside rebate
shall be measured).
9.11.1 5.5 mm thick instead of 4 mm thick sqm 207.50
9.12 Extra for providing frosted glass panes 4 mm thick instead of ordinary
float glass panes 4 mm thick in doors, windows and clerestory
window shutters. (Area of opening for glass panes excluding portion sqm 6.10
inside rebate shall be measured).
9.13 Deduct for providing pin headed glass panes instead of ordinary float
glass panes weighing 4 mm thick in doors, windows and clerestory
sqm 36.60
window shutters (Area of opening for glass panes excluding portion
inside rebate shall be measured).
9.14 Extra for providing ISI marked Stainless Steel butt hinges instead of
M.S. pressed butt hinges bright finished of required size with sqm 105.50
necessary screws. (Shutter area to be measured).
9.15 Deduct for not providing hinges in doors,windows and clerestory
window shutters with
9.15.1 Stainless steel butt hinges with stainless steel screws.

101 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.15.1.1 For 2nd class teak wood and other class of wood shutters.
sqm 154.90
9.15.2 ISI marked M.S. pressed butt hinges bright finished of
required size with necessery screws.
9.15.2.1 For 2nd class teak wood and other class of wood shutters.
sqm 49.40
9.16 Providing and fixing 25 mm thick shutters for cup board etc. :
9.16.1 Panelled or panelled & glazed shutters :
9.16.1.1 Second class teak wood including ISI marked anodised
aluminium butt hinges with necessary screws sqm 2521.30
9.16.1.2 Second class teak wood including ISI marked nickel
plated bright finished M.S. piano hinges with necessary sqm 2454.90
screws
9.16.2 Glazed shutters:
9.16.2.1 Second class teak wood including ISI marked anodised
aluminium butt hinges with necessary screws sqm 2541.80
9.16.2.2 Second class teak wood including ISI marked nickel
plated bright finished M.S. piano hinges with necessary sqm 2513.00
screws
9.17 Providing and fixing flat pressed 3 layer particle board medium
density exterior grade (Grade I) or graded wood particle board IS :
3087 marked, to frame, backing or studding with screws etc.
complete (Frames, backing or studding to be paid separately) :
9.17.1 12 mm thick sqm 500.60
9.17.2 18 mm thick sqm 624.20
9.18 Providing and fixing Pre-laminated flat pressed 3 layer (medium
density) particle board or graded wood particle board IS : 3087
marked, with one side decorative and other side balancing lamination
Grade I, Type II exterior grade IS : 12823 marked, in shelves with
screws and fittings wherever required, edges to be painted with
polyurethane primer (fittings to be paid separately).
9.18.2 18 mm thick sqm 1197.20
9.18.3 25 mm thick sqm 1302.80
9.20 Providing and fixing ISI marked flush door shutters conforming to IS :
2202 (Part I) decorative type, core of block board construction with
frame of 1 st class hard wood and well matched teak 3 ply veneering
with vertical grains or cross bands and face veneers on both faces of
shutters.
9.20.1 35 mm thick including stainless steel butt hinges with
sqm 2369.60
necessary screws-
9.20.2 30 mm thick including stainless steel butt hinges wirh
sqm 2186.50
necessary screws-
9.20.3 25 mm thick (for cupboard) including ISI marked nickel
plated bright finished M.S. Piano hinges IS : 3818 marked sqm 1992.20
with necessary screws

BCD/SOR_8th Edition_October 2016 102

Code
Description Unit Rate Rs.
No.
9.21 Providing and fixing ISI marked flush door shutters conforming to IS :
2202 (Part I) non-decorative type,core of block board construction with
frame of 1 st class hard wood and well matched commercial 3 ply
veneering with vertical grains or cross bands and face veneers on both
faces of shutters:
9.21.1 35 mm thick including ISI marked Stainless Steel butt
hinges with necessary screws sqm 1698.20

9.21.2 30 mm thick including ISI marked Stainless Steel butt

sqm 1515.10
hinges with necessary screws
9.21.3 25 mm thick (for cupboard) including ISI marked nickel
plated bright finished M.S. piano hinges with necessary sqm 1381.80
screws
9.22 Extra for Providing and fixing flush doors with decorative veneering
instead of non decorative ISI marked flush door shutters conforming to
I.S. 2202 (part I).
9.22.1 On one side only sqm 415.00
9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm
minimum depth on all edges of shutters (overall area of door shutter to sqm 366.20
be measured)
9.23A Providing and fixing 25 mm thick shutters for cupboards etc.including
black enamelled M.S. butt hinges with necessary screws :
9.23A.1 Panelled or panelled and glazed shutters
9.23A.1. Second class teak wood sqm 2303.10
9.23A.2 Glazed shutters
9.23A.2.1 Second class teak wood sqm 2497.90
9.24 Extra for providing vision panel not exceeding 0.1 sqm in all type of
flush doors (cost of glas excluded)
9.24.1 Rectangular or Square sqm 140.40
9.24.2 Circular sqm 219.70
9.25 Extra if louvers (not exceeding 0.2 sqm) are provided in flush door
shutters (overall area of door shutters to be measured)
9.25.1 Decorative type door sqm 378.40
9.26 Extra for cutting rebate in flush door shutters {total area of the shutter
sqm 103.80
to be measured)
9.27 Providing and fixing wire gauge shutters using stainless steel grade
304 wire gauge with wire of dia 0.5 mm and average width of aperture
1.4 mm in both directions for doors, windows and clerestory windows
with necessary screws:
9.27.1 35 mm thick shutters
9.27.1.1 With ISI marked M.S. pressed butt hinges bright finished of
required size
9.27.1.1.1 Second class teak wood sqm 2834.80
9.27.1.1.2 Kiln seasoned and chemically treated hollock wood sqm 1833.40
9.27.1.1.3 Kiln seasoned selected class of shesham wood sqm 2638.20
9.27.1.2 With ISI marked stainless steel butt hinges of required size
9.27.1.2.1 Second class teak wood sqm 2940.30
9.27.1.2.2 Kiln seasoned and chemically treated hollock wood sqm 1938.90

103 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.27.1.2.3 Kiln seasoned selected class of sheesham wood sqm 2743.60
9.27.2 30 mm thick shutters
9.27.2.1 With ISI marked M.S. pressed butt hinges bright finished of
required size
9.27.2.1.1 Second class teak wood sqm 2496.80
9.27.2.1.2 Kiln seasoned and chemically treated hollock wood sqm 1640.90
9.27.2.1.3 Kiln seasoned selected class of sheesham wood sqm 2328.50
9.27.2.2 With ISI marked stainless steel butt hinges of required size

9.27.2.2.1 Second class teak wood sqm 2602.30

9.27.2.2.2 Kiln seasoned and chemically treated hollock wood sqm 1746.20
9.27.2.2.3 Kiln seasoned selected class of sheesham wood sqm 2433.90
9.31 Providing and fixing wire gauge laminated veneer lumber shutters
conforming to IS : 14616, and as per TADS 15 :2001 (Part B) using
galvanised wire gauge with average width of aperture 1.4 mm in both
directions with wire of dia 0.63 mm as per IS :1568 for doors, windows
and clerestory windows, including ISI marked M.S. pressed butt hinges
bright finished of required size with necessary screws, as per directions
of Engineer-in-charge:
9.31.1 35 mm thick shutters sqm 2216.20
9.31.2 30 mm thick shutters sqm 1996.40
9.32 Providing 50x50x50 mm 2nd class teak wood plugs including cutting
Each 17.60
brick work and fixing in cement mortar 1:3 (1 cement: 3 coarse sand)
9.33 Providing and fixing expandable fasteners of specified size with
necessary plastic sleeves and galvanised M.S. screws including drilling
holes in masonry work / C.C / R.C.C. and making good etc. complete.
9.33.1 25mm long each 16.50
9.33.2 32 mm long each 18.80
9.33.3 40 mm long each 22.46
9.33.4 50 mm long each 23.70
9.34 Providing and fixing 2nd class teak wood plain lining tongued and
grooved, including wooden plugs complete with necessary screws and
priming coat on unexposed surface.
9.34.1 40 mm thick sqm 4897.70
9.34.2 25 mm thick sqm 3153.00
9.34.3 20 mm thick sqm 2546.80
9.34.4 12 mm thick sqm 1616.40
9.35 Providing and fixing in wall lining flat pressed three layer (medium
density) particle board or graded wood Pre-laminated one side
decorative lamination and other side balancing lamination Grade I,
Type II, IS : 12823 marked, including priming coat on unexposed
surface, with necessary fixing arrangement and screws etc. complete :
9.35.1 12 mm thick sqm 1168.00
9.35.2 18 mm thick sqm 1315.70
9.35.3 25 mm thick sqm 1423.10
9.36 Providing and fixing specified wood frame work consisting of battens
50x25 mm fixed with rawl plug and drilling necessary holes for rawl
plug etc. including priming coat complete.
9.36.1 Kiln seasoned and chemically treated hollock wood cum 89981.60

BCD/SOR_8th Edition_October 2016 104

Code
Description Unit Rate Rs.
No.
9.37 Providing and fixing plywood 4 mm thick, one side decorative veneer
conforming to IS: 1328 (type-1),for plain lining / cladding with
necessary screws, including priming coat on unexposed surface with:

9.37.1 Decorative veneer facings of approved manufacture sqm 1002.20

9.38 Providing and fixing 4 mm thick coir veneer board, ISI marked IS :
14842, plain lining with necessary screws, priming coat on unexposed sqm 811.80
surface etc., complete.
9.39 Providing and fixing skirting with Pre-laminated (one side decorative
and other side balancing lamination) flat pressed 3 layer or graded
particle board (medium density) Grade I, Type II, IS :12823 marked,
with necessary fixing arrangements and screws, including drilling
necessary holes for rawl plugs etc. and priming coat on unexposed
surface complete :
9.39.1 18 mm thick sqm 1513.90
9.39.2 25 mm thick sqm 1621.30
9.40 Providing and fixing wooden moulded beading to door and window
frames with iron screws, plugs and priming coat on unexposed surface
etc. complete:
9.40.1 2nd class teak wood
9.40.1.1 50x12mm m 99.60
9.40.1.2 50x20mm m 139.00
9.40.2 Hollock wood
9.40.2.1 50x12mm m 71.00
9.40.2.2 50x20mm m 91.40
9.41 Providing and fixing plain jaffri of 35x10 mm laths placed 35 mm apart
(frames to be paid separately),including fixing 50x12 mm beading
complete with :
9.41.1 Second class teak wood sqm 1631.30
9.42 Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed
3 layer or graded wood particle board medium density grade I, IS :
3087 marked, including top cover of 6 mm commercial ply wood
conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia (
sqm 312.80
heavy type ) curtain rod with nickel plated brackets, including fixing with
25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats
of size 100 mm x 40 mm x 40 mm on both inner side of pelmet and
rawl plugs 75 mm long etc. all complete.
9.43 Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer
board ISI marked IS : 14842, including top cover of 6 mm coir veneer
board, nickle plated M.S. Pipe 20 mm dia. (heavy type) curtain rod with
nickel plated brackets, including fixing with 25x3 mm M.S. Flat 10 cm m 436.90
long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm
x 40 mm on both inner side of pelmet and rawl plugs 75 mm long etc.
all complete
9.44 Extra for using veneered particle board conforming to IS: 3097 Grade I,
in item of pelmet 18 mm thick 150 mm wide.
9.44.1 Commercial veneered on both sides. m 33.20
9.44.2 Particle board with decorative veneering on both sides m 97.70
9.45 Providing and fixing teak wood lipping of size 25x3 mm in pelmet. m 40.20

105 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.46 Providing and fixing curtain rods of 1.25 mm thick chromium plated
brass plate, with two chromium plated brass brackets fixed with C.P.
brass screws and wooden plugs, etc., wherever necessary complete:

9.46.1 12 mm dia m 268.40

9.46.2 20 mm dia metre m 353.90
9.76.3 25 mm dia metre m 463.80
9.47 Providing and fixing nickel plated M.S. pipe curtain rods with nickel
plated brackets:
9.47.1 20mm dia (heavy type) m 118.90
9.79A.2 25 mm dia (heavy type) m 132.40
9.48 Providing and fixing M.S. grills of required pattern in frames of windows
etc. with M.S. flats, square or round bars etc. including priming coat
with approved steel primer all complete.
9.48.1 Fixed to steel windows by welding kg 86.00
9.48.2 Fixed to openings/ wooden frames with rawl plugs screws
kg 94.20
etc
9.49 Providing and fixing expanded metal 20x60 mm strands 3.25 mm wide
and 1.6 mm thick for windows etc. including 62 x19 mm beading of II
sqm 897.22
nd class teak wood and priming coat with approved steel primer all
complete.
9.50 Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of
weight not less than 7.75 Kg per sqm to window frames etc. including
sqm 1075.20
62x19 mm beading of second class teak wood and priming coat with
approved steel primer all complete.
9.51 Providing and fixing fly proof galvanized M.S. wire gauge to windows
and clerestory windows using wire gauge with average width of
aperture 1.4 mm in both directions with wire of dia 0.63 mm all
complete.
9.51.1 With second class teak wood beading 62x19 mm sqm 811.00
9.51.2 with mild steel U beading sqm 525.10
9.52 Deduct for fixing 75x25 mm hard drawn steel wire fabric of weight not
less than 7.75 kg per sqm in panelled and glazed door and window sqm 122.10
shutter instead of glass sheet 4 mm thick.
9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to
frame with 10 mm diameter bolts,nuts and wooden plugs and
embeddings in cement concrete block 30x10x15 cm 1:3:6 mix (1 Each 94.90
cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal
size)
9.54 Providing beams including hoisting, fixing in position and applying
wood preservative for the unexposed surfaces,etc. complete with:
9.54.1 Sal wood cum 68863.30
9.88.3 Hollock wood cum 44578.90
9.55 Providing and fixing ISI marked M.S. pressed butt hinges bright
finished with necessary screws etc. complete:
9.55.1 125x65x2.12 mm each 30.30
9.55.2 100x58x1.90 mm each 22.10
9.55.3 75x47x1.70 mm each 16.90
9.55.4 50x37x1.5mm each 10.10

BCD/SOR_8th Edition_October 2016 106

Code
Description Unit Rate Rs.
No.
9.56 Providing and fixing ISI marked, IS : 1341, M.S. heavy weight butt
hinges with necessary screws etc. complete :
9.56.1 125x90x4.00 mm each 53.50
9.56.2 100x75x3.50 mm each 32.50
9.56.3 75x60x3.10 mm each 20.60
9.56.4 50x40x2.50 mm each 13.10
9.57 Providing and fixing ISI marked oxidised M.S. pressed butt hinges with
necessary screws etc. complete.
9.57.1 125x65x2.12 mm each 31.40
9.57.2 100x58x1.90 mm each 23.70
9.57.3 75x47x1.70 mm each 18.60
9.57.4 50x37x1.50 mm each 10.90
9.58 Providing and fixing ISI marked oxidised M.S. pressed Parliamentary
hinges with necessary screws etc. complete:
9.58.1 150x125x27x2.80 mm each 55.40
9.58.2 125x125x27x2.80 mm each 52.30
9.58.3 100x125x27x2.80 mm each 42.60
9.58.4 75x100x20x2.24 mm each 36.50
9.59 Providing and fixing ISI marked oxidised M.S. single acting spring
hinges with necessary screws etc.complete:
9.59.1 150 mm each 164.80
9.59.2 125 mm each 158.70
9.59.3 100 mm each 132.80
9.60 Providing and fixing oxidised M.S. double acting spring hinges with
necessary screws etc. complete.
9.60.1 150 mm each 164.80
9.60.2 125 mm each 158.70
9.60.3 100 mm each 132.80
9.61 Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel
plating and fixing with necessary screws etc., complete.
9.61.1 Overall width 35 mm m 134.20
9.61.2 Overall width 50 mm m 130.50
9.61.3 Overall width 65 mm m 145.10
9.62 Providing and fixing ISI marked oxidised M.S. sliding door bolts with
nuts and screws etc. complete :
9.62.1 300x16 mm Each 166.10
9.62.2 250x16 mm Each 158.70
9.63 Providing and fixing ISI marked oxidised M.S. tower bolt black finish,
(Barrel type) with necessary screws etc. complete:
9.63.1 250x10 mm each 65.30
9.63.2 200x10 mm each 57.70
9.63.3 150x10 mm each 44.10
9.63.4 100x10 mm each 37.50
9.64 Providing and fixing ISI marked 85x42mm oxidised M.S. pull bolt lock
conforming to IS : 7534 with necessary screws bolts, nut and washers each 69.60
etc. complete.
9.65 Providing and fixing ISI marked oxidised MS door latches conforming
to IS : 5930 with screws etc.complete.
9.65.1 300x20x6 mm each 67.80
9.65.2 250x20x6 mm each 58.00

107 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.66 Providing and fixing ISI marked oxidised M.S. handles conforming to IS
:4992 with necessary screws etc. complete:
9.66.1 125 mm each 27.70
9.66.2 100 mm each 23.90
9.66.3 75 mm each 22.60
9.67 Providing and fixing oxidised M.S. hasp and staple (safety type)
conforming to IS : 363 with necessary screws etc. complete:
9.67.1 150 mm each 22.40
9.67.2 115 mm each 18.80
9.67.3 90 mm each 15.70
9.68 Providing and fixing oxidised M.S. casement stays (straight peg type)
with necessary screws etc.complete.
9.68.1 300 mm weighing not less than 200 gms each 32.70
9.68.2 250 mm weighing not less than 150 gms each 29.70
9.68.3 200 mm weighing not less than 120 gms each 27.30
9.69 Providing and fixing oxidised M.S. Safety chain with necessary fixtures
each 79.60
for doors, ( weighting not less than 450 gms).
9.70 Providing and fixing IS : 12817 marked stainless steel butt hinges with
stainless steel screws etc.complete:
9.70.1 125x64x1.90 mm each 61.80
9.70.2 100X58X1.90 mm each 54.40
9.70.3 75x47x1.80 mm each 35.90
9.70.4 50x37x1.50 mm each 23.30
9.71 Providing and fixing IS : 12817 marked stainless steel butt hinges
(heavy weight) with stainless steel screws etc. complete:
9.71.1 125x64x2.50 mm each 71.50
9.71.2 100x60x2.50 mm each 55.70
9.71.3 75x50x2.50 mm each 41.40
9.72 Providing and fixing bright finished brass butt hinges with necessary
screws etc. complete:
9.72.1 125x85x5.5 mm (heavy type) each 411.80
9.72.2 125x70x4 mm (ordinary type) each 137.10
9.72.3 100x85x5.5 mm (heavy type) each 359.90
9.72.4 100x70x4 mm (ordinary type) each 109.60
9.72.5 75x65x4 mm (heavy type) each 133.40
9.72.6 75x40x2.5 mm (ordinary type) each 69.90
9.72.7 50x40x2.5 mm (ordinary type) each 29.40
9.73 Providing and fixing bright finished brass parliamentary hinges with
necessary screws etc. complete:
9.73.1 150x125x27x5mm each 373.00
9.73.2 125x125x27x5mm each 330.30
9.73.3 100x125x27x5mm each 305.90
9.73.4 75x100x20x3.2mm each 232.00
9.74 Providing and fixing bright finished brass tower bolts (barrel type) with
necessary screws etc. complete:
9.74.1 250x10mm each 301.50
9.74.2 200x10mm each 236.70
9.74.3 150x10mm each 194.00
9.74.4 100x10mm each 129.70

BCD/SOR_8th Edition_October 2016 108

Code
Description Unit Rate Rs.
No.
9.75 Providing and fixing bright finished brass door latch with necessary
screws etc. complete:
9.75.1 300x16x5mm each 216.50
9.137.2 250x16x5mm each 210.40
9.76 Providing and fixing bright finished brass 100 mm mortice latch and
lock with 6 levers and a pair of lever handles of approved quality with each 514.80
necessary screws etc. complete.
9.77 Providing and fixing bright finished brass 100 mm mortice latch with
one dead bolt and a pair of lever handles of approved quality with each 453.80
necessary screws etc. complete
9.78 Providing and fixing bright finished brass night latch of approved quality
including necessary screws etc. complete. each 667.40
9.79 Providing and fixing special quality bright finished brass cupboard or
ward robe locks with four levers of approved quality including
necessary screws etc. complete.
9.79.1 40 mm each 148.60
9.79.2 50 mm each 154.70
9.79.3 65 mm each 160.80
9.79.4 75 mm each 185.20
9.80 Providing and fixing 50 mm bright finished brass cup board or
wardrobe knob of approved quality with each 47.90
9.81 Providing and fixing bright finished brass handles with screws etc.
complete:
9.81.1 125 mm each 178.10
9.81.2 100 mm each 165.50
9.81.3 75 mm each 128.90
9.82 Providing and fixing bright finished brass hanging type floor door
stopper with necessary screws, etc. each 83.20
9.83 Providing and fixing aluminium die cast body tubular type universal
hydraulic door closer (having brand logo with ISI, IS : 3564, embossed
on the body, door weight upto 35 kg and door width upto 700 mm), each 760.10
with necessary accessories and screws etc. complete.
9.84 Providing and fixing aluminium extruded section body tubular type
universal hydraulic door closer (having brand logo with ISI, IS : 3564,
embossed on the body, door weight upto 36 kg to 80 kg and door width each 1064.70
from 701 mm to 1000 mm), with double speed adjustment with
necessary accessories and screws etc. complete.
9.85 Providing and fixing bright finished brass· casement window fastener
with necessary screws etc.complete. each 69.10
9.86 Providing and fixing bright finished brass casement stays (straight peg
type) with necessary screws etc. complete:
9.86.1 300 mm weighing not less than 330 gms each 174.90
9.86.2 250 mm weighing not less than 280 gms each 142.40
9.86.3 200 mm weighing not less than 240 gms each 130.20
9.87 Providing and fixing bright finished brass hasp and staple (safety type)
with necessary screws etc.complete:
9.87.1 150 mm each 106.90
9.87.2 115 mm each 90.00
9.87.3 90 mm each 79.00

109 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.88 Providing and fixing chromium plated brass 100 mm mortice latch and
lock with 6 levers and a pair of lever handles of approved quality with each 722.30
necessary screws etc. complete.
9.89 Providing and fixing chromium plated brass night latch of approved
quality including necessary screws etc. complete. each 710.10
9.90 Providing and fixing special quality chromium plated brass cupboard
locks with six levers of approved quality including necessary screws
etc. complete.
9.90.1 Size 40 mm each 142.50
9.90.2 Size 50 mm each 154.70
9.90.3 Size 65 mm each 166.90
9.90.4 Size 75 mm each 197.40
9.91 Providing and fixing chromium plated brass 50 mm cupboard or
each 63.70
wardrobe knobs with nuts complete.
9.92 Providing and fixing chromium plated brass handles with necessary
screws etc. complete:
9.92.1 125 mm each 220.80
9.92.2 100 mm each 189.90
9.92.3 75 mm each 165.50
9.93 Providing and fixing chromium plated brass casement window fastener
each 125.30
with necessary screws etc.complete.
9.94 Providing and fixing chromium plated brass casement stays (straight
peg type) with necessary screws etc. complete :
9.94.1 300 mm weighing not less than 330 gms each 192.40
9.94.2 250 mm weighing not less than 280 gms each 168.00
9.94.3 200 mm weighing not less than 240 gms each 149.70
9.95 Providing and fixing ISI marked aluminium butt hinges anodised
(anodic coating not less than grade AC 10 as per IS : 1868)
transparent or dyed to required colour or shade with necessary screws
etc. complete :
9.95.1 125x75x4 mm each 106.40
9.95.2 125x63x4 mm each 101.50
9.95.3 100x75x4 mm each 90.30
9.95.4 100x63x4 mm each 89.10
9.95.5 100x63x3.2 mm each 87.90
9.95.6 75x63x4 mm each 79.50
9.95.7 75x63x3.2 mm each 75.90
9.95.8 75x45x3.2 mm each 66.10
9.96 Providing and fixing aluminium sliding door bolts, ISI marked, anodised
(anodic coating not less than grade AC 10 as per IS : 1868),
transparent or dyed to required colour or shade, with nuts and screws
etc. complete:
9.96.1 300x16 mm each 218.70
9.96.2 250x16 mm each 182.00
9.97 Providing and fixing aluminium tower bolts, ISI marked, anodised
(anodic coating not less than grade AC 10 as per IS : 1868 ),
transparent or dyed to required colour or shade, with necessary screws
etc. complete:
9.97.1 300x10 mm each 111.70
9.97.2 250x10 mm each 93.40
9.97.3 200x10 mm each 78.40
9.97.4 150x10 mm each 64.70
9.97.5 100x10 mm each 51.20

BCD/SOR_8th Edition_October 2016 110

Code
Description Unit Rate Rs.
No.
9.98 Providing and fixing aluminium pull bolt lock, ISI marked, anodised
(anodic coating not less than grade AC 10 as per IS : 1868),
each 69.60
transparent or dyed to required colour and shade, with necessary
screws bolts, nut and washers etc. complete.
9.99 Providing and fixing 50 cm long aluminium kicking plate of size
100x3.15 mm, anodised (anodic coating not less than grade AC 10 as
each 169.20
per IS :1868), transparent or dyed to required colour or shade, with
necessary screws etc. complete.
9.100 Providing and fixing aluminium handles, ISI marked, anodised (anodic
coating not less than grade AC 10 as per IS : 1868) transparent or
dyed to required colour or shade, with necessary screws etc.
complete:
9.100.1 125 mm each 69.40
9.100.2 100 mm each 54.60
9.100.3 75 mm each 46.30
9.101 Providing and fixing aluminium hanging floor door stopper, ISI marked,
anodised (anodic coating not less than grade AC 10 as per IS : 1868)
transparent or dyed to required colour and shade, with necessary
screws etc. complete.
9.101.1 Single rubber stopper each 35.00
9.101.2 Twin rubber stopper each 83.80
9.102 Providing and fixing aluminium casement stays, ISI marked, anodised
(anodic coating not less than grade AC 10 as per IS : 1868)
each 70.30
transparent or dyed to required colour and shade, with necessary
screws etc. complete.
9.103 Providing and fixing bright finished brass 100 mm mortice latch and
lock, ISI marked, with six levers and a pair of anodised (anodic coating
each 766.90
not less than grade AC 10 as per IS : 1868) aluminium lever handles of
approved quality with necessary screws etc. complete .
9.104 Providing and fixing aluminium tee channels (heavy duty) with rollers &
stop end in pelmets as curtain rod. m 65.30

111 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.105 Providing and fixing partition upto ceiling height consisting of G.I. frame
and required board, including providing and fixing of frame work made
of special section power pressed/ roll form G.I. sheet with zinc coating
of 120 gms/ sqm(both side inclusive), consisting of floor and ceiling
channel 50 mm wide having equal flanges of 32 mm and 0.50 mm
thick, fixed to the floor and ceiling at the spacing of 610 mm centre to
centre with dash fastener of 12.5 mm dia meter 50 mm length or
suitable anchor fastener or metal screws with nylon plugs and the
studs 48 mm wide having one flange of 34 mm and other flange 36
mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling
channel and placed at a spacing of 610 mm centre to centre by 6 mm
dia bolts and nuts, including fixing of studs along both ends of partition
fixed flush to wall with suitable anchor fastener or metal screws with
nylon plugs at spacing of 450 mm centre to centre, and fixing of boards
to both side of frame work by 25 mm long dry wall screws on studs,
floor and ceiling channels at the spacing of 300 mm centre to centre.
The boards are to be fixed to the frame work with joints staggered to
avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm
thick having two flanges of 9.5 mm each) to be provided at the
horizontal joints of two boards, fixed to the studs using metal to metal
flat head screws, including jointing and finishing to a flush finish with
recommended jointing compound, jointing tape, angle beads at
corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of
primer suitable for board as per manufacture’s specification and
direction of engineer in charge all complete.

9.105.1 75 mm overall thickness partition with 12.5 mm thick

sqm 1203.60
double skin fire rated board conforming to IS:2095: part I
9.105.2 75 mm overall thickness partition with 12.5 mm thick
double skin tapered edged plain Gypsum board sqm 1032.90
conforming to IS: 2095: part I
9.105.3 66 mm overall thickness Partition with 8 mm thick double
skin Calcium Silicate Board made with Calcareous &
Siliceous materials reinforced with cellulose fiber
sqm 1516.30
manufactured through autoclaving process with
Compressive Strength 225 kg/sq cm, Bending Strength
100 kg/ sq cm
9.105.4 66 mm overall thickness partition using 8 mm thick double
skin non- asbestos multipurpose cement board reinforced
with cellulose fibre manufactured through autoclaving sqm 1228.30
process (High pressure steam cured) as per IS: 14862 with
suitable fibre cement screws
9.106 Providing and fixing PTMT handles with necessary screws etc.
complete.
9.106.1 125x34x24 mm weighing not less than 23 gms each 40.60
9.106.2 150x34x24 mm weighing not less than 26 gms each 45.50
9.107 Providing and fixing PTMT Butt hinges with necessary screws etc.
complete.
9.107.1 75x60x10 mm fitted with 5.5 mm dia M.S. Bright Bar Rod each 60.80
9.107.2 100x75x10 mm fitted with 5.5 mm dia MS Bright Bar Rod each 80.10

BCD/SOR_8th Edition_October 2016 112

Code
Description Unit Rate Rs.
No.
9.108 Providing and fixing PTMT Tower Bolts with 12 mm one piece rod
inside and necessary screws etc.,
9.108.1 152x42x18 mm weighing not less than 60 gms each 85.20
9.108.2 202x42x18 mm weighing not less than 78 gms each 105.10
9.109 Providing and fixing PTMT door catcher of length 72 mm and dia. of 42
mm with suitable washers weighing not less than 33 gms. each 35.40

9.110 Providing and fixing Bamboo jaffery/ fencing consisting of superior

quality 25 mm dia (Average) half cut bamboo placed vertically and
fixed together with three numbers horizontal running members of
sqm 369.10
hallock wood in scantling of section 50X25 mm, fixed with nails and G.I
wire on existing support, complete as per direction of Engineer-in-
Charge.
9.111 Providing and fixing wooden moulded corner beading of triangular
shape to the junction of panelling etc. with iron screws, plugs and
priming coat on unexposed surface etc. complete 2nd class teak wood.

9.111.1 50x50 mm (base and height) m 174.30

9.112 Providing and fixing 2nd class teak wood lipping / moulded beading or
taj beading of size 18X5 mm fixed with wooden adhesive of approved
quality and screws / nails on the edges of the Pre-laminated particle m 50.00
board as per direction of Engineer-in-Charge.

9.113 Providing and fixing bright finished 100 mm mortice lock with 6 levers
without pair of handles of approved quality for aluminium door, with
each 446.20
necessary screws etc complete as per direction of Engineerin- charge.

9.114 Providing and fixing magnetic catcher of approved quality in cupboard /

ward robe shutters, including fixing with necessary screws etc.
complete .
9.114.1 Triple strip vertical type each 29.80
9.114.2 Double strip (horizontal type) each 23.70
9.115 Providing and fixing powder coated telescopic drawer channels 300
mm long with necessary screws etc. complete as per directions of each set 195.60
Engineer-in-charge.
9.116 Providing and fixing sliding arrangement in racks/ cupboards/cabinets
shutter by with stainless steel rollers to run inside C or E aluminium
channel section (The payment of C or E channel shall be made each 11.90
separately)
9.117 Providing and fixing factory made uPVC door frame made of uPVC
extruded sections having an overall dimension as below (tolerance
±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door
frame to be Jointed with galvanized brackets and stainless steel
screws, joints mitred and plastic welded. The hinge side vertical of the
frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1
mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to
the frame complete as per manufacturer’s specification and direction of
Engineer-in-charge
9.117.1 Extruded section profile size 48x40 mm m 201.00
9.117.2 Extruded section profile size 42x50 mm m 188.80

113 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.118 Providing and fixing to existing door frames.
9.118.1 24 mm thick factory made PVC door shutters made of
styles and rails of a uPVC hollow section of size 59x24 mm
and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on
both sides. The styles and rails mitred and joint at the
corners by means of M.S. galvanised/plastic brackets of
size 75x220 mm having wall thickness 1.0 mm and
stainless steel screws. The styles of the shutter reinforced
by inserting galvanised M.S. tube of size 20x20 mm and 1
mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’
section, a uPVC hollow section of size 100x24 mm and 2
mm (± 0.2 mm) wall thickness, fixed to the shutter styles sqm 2731.90
by means of plastic/galvanised M.S. ‘U’ cleats. The shutter
frame filled with a uPVC multichambered single panel of
size not less than 620 mm, having over all thickness of 20
mm and 1 mm (± 0.1 mm) wall thickness. The panels filled
vertically and tie bar at two places by inserting horizontally
6 mm galvanised M.S. rod and fastened with nuts and
washers, complete as per manufacturer’s specification
and direction of Engineer-in-charge. (For W.C. and
bathroom door shutter).
9.118.2 30 mm thick factory made Polyvinyl Chloride (PVC) door
shutter made of styles and rails of a uPVC hollow section
of size 60x30 mm and wall thickness 2 mm (± 0.2 mm),
with inbuilt decorative moulding edging on one side. The
styles and rails mitred and joint at the corners by means of
M.S. galvanised/plastic brackets of size 75x220 mm having
wall thickness 1.0 mm and stainless steel screws. The
styles of the shutter reinforced by inserting galvanised M.S.
tube of size 25x20 mm and 1 mm (± 0.1 mm) wall
thickness. The lock rail made up of ‘H’ section, a uPVC sqm 2854.00
hollow section of size 100x30 mm and 2 mm (± 0.2 mm)
wall thickness fixed to the shutter styles by means of
plastic/ galvanised M.S. ‘U’ cleats. The shutter frame filled
with a uPVC multi-chambered single panel of size not less
than 620 mm, having over all thickness of 20 mm and 1
mm (± 0.1 mm) wall thickness . The panels filled vertically
and tie bar at two places by inserting horizontally 6 mm
galvanised M.S. rod and fastened with nuts and washers,
complete as per manufacturer’s specification and direction
of Engineer-incharge.

BCD/SOR_8th Edition_October 2016 114

Code
Description Unit Rate Rs.
No.
9.118.3 25 mm thick PVC flush door shutters made out of a one
piece Multi chamber extruded PVC section of the size of
762mm X 25 mm or less as per requirement with an
average wall thickness of 1 mm (± 0.3 mm). PVC foam
end cap of size 23x10 mm are provided on both vertical
edges to ensure the overall thickness of 25 mm. An M.S.
tube having dimensions 19 mm x 19 mm and 1.0 mm (±
0.1 mm) is inserted along the hinge side of the door. Core
of the door shutter should be filled with High Density sqm 2731.90
Polyurethane foam. The Top & Bottom edges of the
shutter are covered with an end-cap of the size 25mm X 11
mm. Door shutter shall be reinforced with special
polymeric reinforcements as per manufacturer’s
specification and direction of Engineer-in-charge to take up
necessary hardware and fixtures. Stickers indicating the
locations of hardware will be pasted at appropriate places.

9.119 Providing and fixing factory made P.V.C. door frame of size 50x47 mm
with a wall thickness of 5 mm,made out of extruded 5 mm rigid PVC
foam sheet, mitred at corners and joined with 2 Nos. of 150 mm long
brackets of 15x15 mm M.S. square tube, the vertical door frame
profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, m 446.50
EPDM rubber gasket weather seal to be provided through out the
frame. The door frame to be fixed to the wall using M.S. screws of
65/100 mm size, complete as per manufacturer’s specification and
direction of Engineer-in-Charge.
9.120 Providing and fixing factory made panel PVC door shutter consisting of
frame made out of M.S. tubes of 19 gauge thickness and size of 19
mm x 19 mm for styles and 15x15 mm for top & bottom rails.
M.S.frame shall have a coat of steel primers of approved make and
manufacture . M.S. frame covered with 5 mm thick heat moulded PVC
‘C’ channel of size 30 mm thickness, 70 mm width out of which 50 mm
shall be flat and 20 mm shall be tapered in 45 degree angle on both
side forming styles and 5 mm thick,95 mm wide PVC sheet out of
which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on
the inner side to form top and bottom rail and 115 mm wide PVC sheet
out of which 75 mm shall be flat and 20 mm shall be tapered on both
sides to form lock rail. Top, bottom and lock rails shall be provided both
side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC
sheet be provided as gap insert for top rail & bottom rail. paneling of 5
mm thick both side PVC sheet to be fitted in the M.S. frame
welded/sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15
mm wide PVC sheet beading on inner side, and joined together with
solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm
width is to be stuck on the interior side of the ‘C’ Channel using PVC
solvent adhesive etc. complete as per direction of Engineer-in-charge,
manufacturer’s
9.120.1 30 mm specification
thick plain& PVC
drawing.
door shutters sqm 2762.90
9.120.2 30 mm thick pre laminated PVC door shutters sqm 3251.10

115 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.121 Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames
of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15
mm to receive shutter of 30 mm thickness.The laminate shall be
moulded with fire resistant grade unsaturated polyester resin and
m 483.10
chopped mat . Door frame laminate shall be 2 mm thick and shall be
filled with suitable wooden block in all the three legs. The frame shall
be covered with fiber glass from all sides. M.S. stay shall be provided
at the bottom to steady the frame.
9.122 Providing and fixing to existing door frames.
9.122.1 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled
door shutter of required colour and approved brand and
manufacture, made with fire - retardant grade unsaturated
polyester resin, moulded to 3 mm thick FRP laminate for
forming hollow rails and styles, with wooden frame and sqm 2396.60
suitable blocks of seasoned wood inside at required places
for fixing of fittings, cast monolithically with 5 mm thick
FRP laminate for panels conforming to IS: 14856, including
fixing to frames.
9.122.2 30 mm thick Fiber glass Reinforced Plastic (F.R.P.) flush
door shutter in different plain and wood finish made with
fire retardant grade unsaturated polyester resin, moulded
to 3 mm thick FRP laminate all around, with suitable
wooden blocks inside at required places for fixing of fittings sqm 2762.90
and polyurethane foam (PUF) / Polystyrene foam to be
used as filler material throughout the hollow panel, casted
monolithically with testing parameters of F.R.P. laminate
conforming to table - 3 of IS: 14856, complete as per
direction of Engineer-in-charge.
9.123 Providing and fixing factory made door frame (single rebate) made out
of single piece extruded solid PVC foam profile with homogenous fine
cellular structure having smooth outer integral skin having 62 mm width
m 373.20
& 32 mm thickness, frame will be mitred & Jointed with self driven self
tapping screws of size 38 mm x 4 mm & PVC solvent cement ,
including fixing the frame to wall with suitable dia & length
9.124 Providing and fixing factory made 30 mm thick door shutter made of
solid PVC foam profile. The styles & rails shall be of size 75 mm x 30
mm having wall thickness 5 mm. The styles, top & bottom rails shall
have one side wall thickness of 15 mm integrally extruded on the hinge
side of the profile for better screw holding power. The styles and rails
shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1mm,
painted with primer, all four corners of reinforcement to be welded or
sealed. Solid PVC extruded bidding (push fit type) will be set inside the
styles and the rails with a cavity, to receive single piece extruded 5 mm
PVC sheet as panel. The styles and rails will be mitred cut and joint
with the help of PVC solvent cement & self driven self tapping screws.
Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with
wall thickness 5 mm & 15 mm integrally extruded in the middle of the
lock rail & fixed with styles with the help of PVC solvent cement & self
driven self tapping screws of size 100 mm x 8mm complete as per
manufacturer’s specifications and direction of Engineer-in-charge.
9.124.1 Non decorative finish sqm 2711.60
9.124.2 Decorative finish (both side wood grained finish) sqm 3373.20

BCD/SOR_8th Edition_October 2016 116

Code
Description Unit Rate Rs.
No.
9.125 Providing and fixing PVC rigid foam sheet 1 mm thick on existing door
shutters (bathroom and W.C.doors) using synthetic rubber based sqm 647.60
adhesive.
9.126 Providing and fixing 12 mm thick panelling or panelling and glazing in
panelled or panelled and glazed shutters for doors, windows and
clerestory windows (area of opening for panel inserts excluding portion
inside grooves or rebates to be measured). Panelling for panelled or
panelled and glazed shutters 25 mm to 40 mm thick.
9.126.1 Marine plywood conformingto IS : 710 sqm 1536.60
9.126.2 Fire retardant plywood conforming to IS : 5509 sqm 1580.30
9.127 Providing & Fixing decorative high pressure laminated sheet of plain /
wood grain in gloss / matt / suede finish with high density protective
surface layer and reverse side of adhesive bonding quality conforming
to IS : 2046 Type S, including cost of adhesive of approved quality.

9.127.1 1.5 mm thick sqm 816.90

9.127.2 1.0 mm thick sqm 669.10
9.128 Providing and fixing factory made Fiber glass Reinforced plastics
(F.R.P.) chajja 4 mm thick of required colour, size and design made by
Resin Transfer Moulding (RTM) Machine Technology, resulting in void
free compact laminate in single piece, having smooth gradual slope
curvature for easy drainage of water and duly reinforced by 2 nos
vertically and 1nos horizontally 50x2 mm thick M.S. flat with 12 mm in
built hole for grouting on the existing wall along with the 50 mm flanges
sqm 5040.70
duly inserted and sealed in the wall complete in one single piece
casted monolithically, including all necessary fittings. The FRP Chajja
should be manufactured using unsaturated Polyester resin as per IS :
6746, duly reinforced with fibre glass chopped strand mat (CSM) as
per IS : 11551 complete with protective Gel coat U/V coating on Top
for complete resistance from the extreme of temperature, weather &
sunlight.
9.129 Providing and fixing cup board shutters 25 mm thick, with Pre-
laminated flat pressed three layer particle board or graded wood
particle board IS : 12823 marked, exterior grade (Grade I Type II),
having one side decorative lamination and other side balancing
sqm 1596.50
lamination, including IInd class teak wood lipping of 25 mm wide x12
mm thick with necessary screws and bright finished stainless steel
piano hinges, complete as per direction of the Engineer-in-Charge.

9.130 Providing and fixing cup board shutters with 25 mm thick veneered
particle board IS : 3097 marked,exterior grade (Grade I), of approved
make including IInd class teak wood lipping of 25 mm wide x 12mm
thick with necessary screws and bright finished stainless steel piano
hinges, complete as per direction of Engineer-in-Charge.

9.130.1 With decorative veneering on one side and commercial

veneering on other side sqm 1352.40

9.130.2 With non decorative veneering on both sides sqm 1242.50

117 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.131 Providing and fixing factory made shutters of pre-laminated particle
board flat pressed three layer or graded wood particle board with one
side decorative finish and other side balancing lamination conforming to
IS : 12823 Grade I Type II, of approved design, and edges sealed with
water resistant paint and lipped with aluminium ‘U’ type edge beading
all-round the shutter, including fixing with angle cleat, grip strip,
cadmium plated steel screws, including fixing of aluminium hinges
100x63x4mm etc. complete as per architectural drawing and direction
of Engineer-in-Charge (Cost of ‘U’beading and hinges will be paid for
separately).
9.131.1 25 mm thick sqm 1291.80
9.132 Providing and fixing aluminum U beading of required size to Pre
laminated / flush door shutter, including fixing etc. complete as per Per Kg 456.50
direction of Engineer-in-Charge.
9.133 Providing and fixing, in position concealed G.I. section for wall paneling
using board of required thickness fixed on the ‘W’ profile (0.55 mm
thick ) having a knurled web of 51.55 mm and two flanges of 26 mm
each with lips of 10.55 mm, placed @ 610 mm C/C in perimeter
channel having one flange of 20 mm and another flange of 30 mm with
thickness of 0.55 mm and web of length 27 mm.Perimeter channel is
fixed on the floor and the ceiling with the nylon sleeves @ 610 mm C/C
with fully threaded self-tapping dry wall screws. Board is fixed to the ‘W’
profile with 25 mm countersunk ribbed head screws @ 200 mm C/C.,
all complete as per the drawing & directions of engineer-incharge, the
joints of the boards are finished with specially formulated jointing
compound and 48 mm wide jointing tape to provide seamless finish.

9.133.1 Tapered edge calcium silicate board made with calcareous

& siliceous materials reinforced with cellulose fiber
manufactured through autoclaving process to give stable
crystalline structure with compressive strength 225
kg/sqcm, Bending strength 100 kg/sqcm.

9.133.1.1 10 mm thick sqm 892.10

9.133.2 Non-asbestos multipurpose cement board reinforced with
cellulose fibre manufactured through autoclaving process
(high pressure steam cured) as per IS :14862 with suitable
fibre cement screw
9.133.2.1 8 mm thick sqm 704.00
9.133.3 Gypsum board conforming to IS: 2095 Part - I
9.133.3.1 12.5 mm thick sqm 596.60
9.134 Providing and fixing wire gauge shutters using stainless steel grade 304
wire gauge with wire of dia 0.5 mm and average width of aperture 1.4
mm in both directions for doors, windows and clerestory windows with
necessary screws:
9.134.1 35 mm thick shutters
9.134.1.1 with ISI marked M.S. pressed butt hinges bright finished of
required size
9.134.1.1.1 Second class teak wood sqm 3297.00
9.134.1.1.2 Kiln seasoned and chemically treated hollock wood sqm 2295.40

BCD/SOR_8th Edition_October 2016 118

Code
Description Unit Rate Rs.
No.
9.134.1.1.3 Kiln seasoned selected class of sheesham wood sqm 3100.30
9.134.1.2 With ISI marked stainless steel butt hinges of required size

9.134.1.2.1 Second class teak wood sqm 3402.50

9.134.1.2.2 Kiln seasoned and chemically treated hollock wood sqm 2401.00
9.134.1.2.3 Kiln seasoned selected class of sheesham wood sqm 3205.80
9.134.2 30 mm thick shutters sqm
9.134.2.1 with ISI marked M.S. pressed butt hinges bright finished of
required size
9.134.2.1.1 Second class teak wood sqm 2959.00
9.134.2.1.2 Kiln seasoned and chemically treated hollock wood sqm 2102.90
9.134.2.1.3 Kiln seasoned selected class of sheesham wood sqm 2790.60
9.134.2.2 With ISI marked stainless steel butt hinges of required size
9.134.2.2.1 Second class teak wood sqm 3064.40
9.134.2.2.2 Kiln seasoned and chemically treated hollock wood sqm 2208.40
9.134.2.2.3 Kiln seasoned selected class of sheesham wood sqm 2896.10
9.135 Providing and fixing fly proof stainless steel grade 304 wire gauge, to
windows and clerestory windows using wire gauge with average width
of aperture 1.4 mm in both directions with wire of dia 0.50 mm all
complete.
9.135.1 With 2nd class teak wood beading 62X19 mm sqm 1587.40
9.135.2 With 12 mm mild steel U beading sqm 1302.10
9.136 Providing and fixing fire resistant door frame of section 143 x 57 mm
having built in rebate made out of 16 SWG G.I.sheet (zinc coating not
less than 120 gm/sqm) duly filled with vermuculite based concrete mix,
suitable for mounting 60 minutes fire rated door shutters. The frame is
fitted with intumuscent fire seal strip of size 10x4 mm (minimum) m 1251.20
alround the frame and fixing with dash fastener of approved size and
make, including applying a coat of approved brand fire resistant primer
etc. complete as per direction of Engineer-in-charge (Dash fastener to
be paid for separately).
9.137 Providing and fixing 50 mm thick glazed fire resistant door shutters of
60 minutes fire rating conforming to IS:3614 (Part-II), tested and
certified as per laboratory approved by Engineer-in-charge, with
suitable mounting on door frame, consisting of vertical styles, lock rail,
top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG
sqm 6520.80
G.I. sheet (zinc coating not less than 120 gm/ m2) duly filled FR
insulation material and fixing with necessary stainless steel ball bearing
hinges of approved make, including applying a coat of approved fire
resistant primer etc. all complete as per direction of Engineer-incharge
(panneling to be paid for separately).
9.138 Providing and fixing glazing in fire resistant door shutters, fixed panels,
ventilators and partitions etc.,with G.I. beading of appropriate size,
made out of 20 SWG G.I.sheet (zinc coating not less than 120 gm/m2),
fire resistant sealant, including applying a coat of approved fire
resistant primer on G.I. beading etc., complete all as per direction of
Engineer-in-charge.
9.138.1 With clear fire resistant glass panes 6 mm thick of
approved brand, having minimum 60 minutes fire sqm 28328.20
resistance

119 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.139 Providing and fixing panic bar / latch (Double point) fitted with a single
body, Trim Latch & Lock on backside of the Panic Latch of reputed
Each 6166.70
brand and manufacture to be approved by the Engineer- in- charge,all
complete.
9.140 Providing and fixing plain lining with necessary screws/nuts &
9.140.1 12 mm thick commercial ply conforming to IS : 1328 BWR
sqm 892.90
type
9.141 Providing and fixing PVC Door Frame of size 50x47 mm with a wall
thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC
profile, with mitred cut joints and joint with 2 nos of PVC bracket of size
190 mm x 100 mm long arms of cross section size 35 x 15 mm & self
driven self taping screws,the vertical door profiles to be reinforced with
40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM m 619.00
rubber gasket weather seal throughout the frame, including jointing 5
mm PVC frame strip with PVC solvent cement on the back of the
profile. The door frame to be fixed to the wall using 8 x100 mm long
anchor fasteners complete, all as per manufacturer’s specification and
direction of Engineer -in- charge.

9.142 35 mm thick factory made Solid panel PVC Door shutter, made out of
single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick,
having styles & rails (except lock rail) of size 95 mmx 35 mm x 5
mm,out of which 75 mm shall be flat and 20 mm shall be tapered (on
both side), having one side thickness of 15 mm integrally extruded on
the hinge side of the profile for better screw holding power, including
reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of
styles & rails to be mitered cut & joint with the help of PVC solvent
cement, self driven self tapping screws & M.S. rectangular pipes
bracket of size 190 mm X 100 mm of cross section size 35 mm x 17
mm x 1 mm at each corner. Single piece extruded 5mm thick solid PVC
Lock rail of size 115 mm x 35 mm x 35 mm, out of which 95 mm to be
flat and 20 mm to be tapered at both ends, having 15 mm solid core in
middle of rail section integrally extruded, fixing the styles & rails with
the help of solvent and self driven self tapping screws of 125 mm x 11
mm, including providing 5 mm Single piece solid PVC extruded sheet
inserted in the door as panel,all complete as per manufacturer’s
specification and direction of Engineer-in-charge.
9.142.1 Non decorative finish (matt finish) sqm 2710.50
9.142.2 Decorative finish (wood grained finish) sqm 3320.80
9.143 Providing and Fixing factory made uPVC door frame, made of uPVC
exturded sections, of size 65 mm x 55 mm with wall thickness 2.0 mm (
± 0.2 mm) , corners of the door frame to be mitred cut and jointed with
plastic brackets and stainless steel screws, reinforcing hinge side
vertical of the frames with PVC profile of Size 28 mm x 30 mm having
m 420.80
wall thickness 2 mm (±0.2 mm), including providing & fixing 3 nos of
125 mm long stainless steel hinges to the frame, fixing the frame with
jamb with required number & size of anchor dash fastners, all
complete as per manufacturer’s specification and direction of Engineer-
in-charge.

BCD/SOR_8th Edition_October 2016 120

Code
Description Unit Rate Rs.
No.
9.144 Providing and fixing 37 mm thick factory made PVC door shutter, styles
and rails made of PVC hollow section of size 100 mm x 37 mm with
wall thickness 2 mm ( ± 0.2 mm), with inbuilt bead on one side, styles
and rails mitered cut and joint at the corners by means of 2 nos of
plastic brackets of size 75 mm PVC profile of size 28 mm x 30 mm,
with wall thickness 2 mm ( ± 0.2 mm). Lockrail of size 100 mm x 37 sqm 2976.00
mm, wall thickness 2 mm (± 0.2 mm) will be fixed to the vertical styles.
Providing with PVC snapfit beads and panel of size 100 mm x 20 mm,
and inserting 2 nos tie bar of 6 mm dia and fastening with nuts and
washers complete, all as per manufacturer’s specification and direction
of Engineer-incharge.
9.145 Providing and Fixing factory made PVC door frame made of PVC
extruded sections of size 75 mm x 53 mm, having wall thickness 2.0
mm (± 0.2 mm). Both verticals sides of the frame reinforced with PVC
profile of cross section size 28 mm x 30 mm x 2 mm thickness (± 0.2
mm) and 75 mm x 200 mm long, including reinforcing both ends of the
top frame with PVC profile. PVC Door Frame and PVC reinforcement m 445.20
profile to be mitred cut jointed and fusion welded together, including
providing and fixing 3 nos of 125 mm long stainless steel hinges to
frame, fixing the frame with jamb with required nos & sizes of anchor
dash fastener, all complete as per manufacturer’s specification and
direction of engineer-incharge.
9.146 Providing and fixing 37 mm thick factory made PVC Door shutter,
styles and rails made of PVC hollow extruded printed and laminated
section having overall dimension 115 mm x 37 mm with wall thickness
2 mm (± 0.2 mm) with inbuilt beading on one side, the styles and rails
mitred cut and joint at corners by inserting 2 nos PVC profile
reinforcement of size 75 mm x 200 mm long with cross section size of
28 mm x 30 mm having wall thickness 2 mm (± 0.2 mm). Styles, rails
and reinforcements to be fusion welded together. Only hinge side
vertical style to be reinforced with PVC profile reinforcement in full sqm 3098.10
length. Printed and laminated PVC lock rail of size 110 mm x 37 mm
having wall thickness 2 mm (± 0.2 mm) to be welded horizontally with
the vertical styles after inserting PVC profile reinforcement as in styles
and rails, providing with PVC snap fit beading, panels of 100 x 20 mm
printed & laminated and inserting 2 nos 6 mm dia bright steel rod
horizontally with both side threaded and tightened with check nuts and
washers complete, all as per manufacturer’s specification and direction
of engineer-incharge.

121 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.147 Providing and Fixing factory made uPVC white colour casement/sliding
window/ door, made of extruded profiles. Profiles of frames and sash
will be mitered cut and fusion welded at all corners, including drilling of
holes for fixing hardware and drainage of water etc., making
arrangement for fixing of hardware, EPDM gasket, 1.2 ± 0.2 mm thick
galvanised steel profile to be inserted in required profile, frame will be
fixed to the wall with 8 mm x 100 mm long fasteners, all complete as
per direction of Engineer-in-charge (Glazing, hardware hinges and
fitting etc. to be paid separately). Note:- Each member of window to be
measured separately with clear length.

9.147.1 Casement Window (Outward/Inward opening) with

hinge System
9.147.1.1 Frame (50 mm x 50 mm) m 395.50
9.147.1.2 Sash (Style and Rail) (62 mm x 34 mm) m 376.20
9.147.1.3 Mullion (intermediate Section) (66 mm x 50 mm) m 421.10
9.147.1.4 ‘T’ Profile (one vertical length in between two shutters) (24
mm x 34.5 mm) m 92.00

9.147.1.5 Glazing bead (12 mm x 18 mm) m 124.00

9.147.2 Casement Window (With friction hinge & outward
opening)
9.147.2.1 Casement Frame (67 mm x 62 mm) m 453.10
9.147.2.2 Casement Window Sash/Mullion (67mm x 75mm ) (style,
rail and intermediate section) m 491.60

9.147.2.3 Casement Glazing bead (35 mm x 18 mm) m 168.90

9.147.3 Sliding Window (Two Track, 2/4 Shutters)
9.147.3.1 Two Track Sliding Frame (67 mm x 52 mm) m 540.40
9.147.3.2 Sliding window Sash (60 mm x 44 mm) m 503.20
9.147.3.3 Sliding Interlock for Window (one vertical length in each
m 132.10
shutter)( 45.5 mm x 28 mm)
9.147.3.4 Sliding Glazing bead (35 mm x 18 mm) m 168.90
9.147.4 Sliding Door (Two Track, 2/4 Shutters)
9.147.4.1 Two Track Sliding Frame (67 mm x 52 mm) m 518.70
9.147.4.2 Sliding Door Sash (80 mm x 44 mm) m 634.90
9.147.4.3 Sliding Interlock for Door (one vertical length in each
m 132.10
shutter) (45.5 mm x 28 mm)
9.147.4.4 Sliding Glazing bead (35 mm x 18 mm) m 168.90
9.148 Providing and fixing stainless steel (SS-304 grade) friction hinges to the
side/ top hung uPVC windows,of approved quality, with necessary
stainless steel screws etc. as per direction of Engineer-incharge.

9.148.1 200 x 19 x 1.9 mm each 290.20

9.148.2 250 x 19 x 1.9 mm each 363.50
9.148.3 300 x 19 x 1.9 mm each 461.10
9.148.4 350 x 19 x 1.9 mm each 522.10
9.148.5 400 x 19 x 1.9 mm each 656.40

BCD/SOR_8th Edition_October 2016 122

Code
Description Unit Rate Rs.
No.
9.149 Providing and fixing casement handle made of zinc alloyed (white
powder coated) for uPVC casement window with necessary screws etc. each 200.50
complete.
9.150 Providing and fixing zinc alloyed (white powder coated) touch lock for
uPVC sliding window with necessary screws etc. complete. each 139.50
9.151 Providing and fixing steel roller for uPVC sliding window with necessary
each 66.20
screws etc. complete.
9.152 Providing and fixing steel roller for uPVC sliding door with necessary
each 108.90
screws etc. complete.
9.153 Providing and fixing steel (white power coated) crescent lock for uPVC
sliding window/ door with necessary screws etc. complete. each 127.30

9.154 Providing and fixing frame work for partitions/ wall lining etc. made of
50x50x1.6 mm hollow MS tube,placed along the walls, ceiling and floor
in a grid pattern with spacing @bolt, including making provision for
opening for doors, windows, electrical conduits, switch boards 60 cm
centre to centre both ways (vertically & horizontally ) or at required Per Kg 1063.30
spacing near opening, with necessary welding at junctions and fixing
the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia,
75 mm long etc., including providing with two coats of approved steel
primer etc. complete, all as per direction of Engineer-in-charge.
9.155 Providing and fixing panelling or paneling and glazing in panelled or
panelled and glazed shutters for doors, windows and clerestory
windows ( area of opening for panel grooves or rebated to be
measured). Panelling for panelled and glazed shutters 25mm to sqm 1326.00
40mminserts excluding portion inside thick:Pre-laminated with
decorative lamination on both side exterior Grade - I MDF Board 12
mm thick confirming to IS:14587
9.156 Providing and fixing Pre -laminated medium density fibre board exterior
grade (Grade-I) IS:14587:1998 marked, to frame, backing or studding
with screws etc. complete ( Frames, backing or studding to be paid
separately).
9.156.1 Pre-laminated with decorative lamination on both side
exterior Grade - I MDF Board 12 mm thick confirming to sqm 970.80
IS:14587
9.156.2 Pre-laminated with decorative lamination on both side
exterior Grade - I MDF Board 18 mm thick confirming to sqm 1268.20
IS:14587
9.157 Providing and fixing Pre-laminated medium density fibre board IS:
14587:1998 marked, with one side decorative lamination other side
balancing lamination Grade-I(exterior grade) in shelves with screws and
fittings wherever required, edges to be sealed with PVC edge bending
tape 2.00 mm thick of approved brand (fittings to be paid separately).

9.157.1 Pre-laminated with decorative lamination one side and

other side balancing lamination exterior Grade - I MDF sqm 1385.10
Board 18 mm thick confirming to IS:14587
9.157.2 Pre-laminated with decorative lamination one side and
other side balancing lamination exterior Grade - I MDF sqm 1820.80
Board 25 mm thick confirming to IS:14587

123 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
9.158 Providing and fixing in wall lining medium density fibre board IS:
14587:1998 marked, Pre-laminated one side decorative lamination and
other side balancing lamination, with necessary fixing arrangement and
screws etc. complete.
9.158.1 12 mm thick. sqm 1008.40
9.158.2 18 mm thick. sqm 1303.10
9.158.3 25 mm thick. sqm 1756.20
9.159 Providing and fixing 25mm thick pre-laminated medium density fibre
board exterior grade ( Grade-I) IS:14587:1998 marked one side
decorative and other side balancing lamination for cupboard shutters
edges to be sealed with PVC edge bending tape 2.00 mm thick of sqm 1844.60
approved brand including ISI marked nickeled plated bright finishing
M.S. piano hinges IS:3818 marked with necessary screwed complete.

9.160 Providing and fixing skirting with Pre-laminated medium density fibre
board exterior grade (Grade-I) IS: 14587:1998 marked, (one side
decorative and other side balancing lamination) with necessary fixing
arrangements and screws, including drilling necessary holes for rawl
plugs etc. and edges to be sealed with PVC edge bending tape 2.00
mm thick of approved brand complete.

9.160.1 18 mm thick. sqm 1675.50

9.160.2 25 mm thick. sqm 2128.70

BCD/SOR_8th Edition_October 2016 124

SUB HEAD : 10.0
STEEL WORK
 BUILDING WORK - Contd.

10.0 Steel Work

Code
Description Unit Rate Rs.
No.
10.1 Structural steel work in singal section fixed without connecting plate kg 59.20
including cutting.hoisting,fixing in position and applying a priming
coat of approved steel primer all complete.
10.3 Structural steel work riveted or bolted in built up sections, trusess kg 69.20
and framed work, including cutting,hoisting,fixing in position and
applying a priming coat of approved ateef primer all complete.
10.5 Providing and fixing in position collapsible steel shutters with vertical sqm 4248.20
channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm
size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia
steel pulleys complete with bots.nuts locking arrangement stoppers
handies including applying a priming coat of approved steel primer.
10.6 Providing and fixing 1 mm thick M.S.sheet sliding - shutters with sqm 2986.70
frame and diagonal braces of 40x40x6 mm angle iron,3 mm M.S.
gusset plates at the junction and corners, 25 mm dia pulley, 40x40x6
mm angle and T-iron guide at the top bottem respectively including
applying a priming coat of approved steel primer.
10.7 Providing and fixing 1 mm thick M.S. sheet door with frame of sqm 2617.00
40x40x6 mm angle iron and 3mm MS gusset plates at the junction
and corners.all necessary fittings completejncluding applying a
priming coat of approved steel primer.
10.7.1 Using flats 30x6 mm for diagonal braces and central cross sqm 2503.00
piece.
10.8 Supplying and fixing-rolling shuters of approved make.made of
required size of M.S.Iaths inter locked together through their intire
length and jointed together at the end by end locks mounted on
specially designed pipe shaft with brackets, side guides and
arragements for inside and outside locking with push and pull
operation complete including the cost of prioviding and fixing
necessary 27.5 cm long wire springs grade no. 2 and M.S. top cover
of required thickness for rolling shutters.
10.8.1 80x1.25mmM.S. Laths with 1.25mm thick top cover. sqm 2052.00
10.8.2 80x1.20mm thick M.S. laths with 1.20 mm thick top cover. sqm 1828.20
10.8.3 80x0.90 mm thick M.S. laths with 0.90 mm thick top cover. sqm 1730.60
10.9 Providing and fixing ball bearing for rolling shutters sqm 458.40
10.1 Extra for providing mechanical device chain and crank operation for
operating rolling shutters:
10.10.1 Exceeding 10.00 sqm and upto 16.80 sqm in area (say sqm 699.30
average 14 sqm)
10.10.2 Exceeding 16.80 sqm in area sqm 735.90
10.10A Extra for providing grilled rolling shutters manufactured out sqm 329.60
of 8 mm dia. M.S. bar instead of laths as per design
approved by Engineer-in-charge (area of grill to be
measured.)

125 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
10.11 Fixing standard steel glazed doors, windows and ventilators in walls Kg 29.80
with 15x3 mm lugs 10 cm long embedded in cement concrete blocks
15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 gradded stone
aggregate 20 mm nominal size) or with wooden plugs and screws or
rawl plugs and screws or with fixing clips or with bolts and nuts as
required , including fixing of glass panes with glazing cfips and
special metal-sash putty of approved make, or metal beading with
screwsfonly steel windows with lugs, glass panes screws, shall be
supplied by department free of cost)
10.11.1 Fixing with carbon steel galvanised dash fastener of required dia and kg 15.70
size (to be paid for separately).
10.12 Providing and fixing steel glazed doors, windows and ventilators of
standard rolled steel sections, joints mitered and welded with 15x3
mm lugs 10 cm long with steel lugs embedded in cement concrete
blocks 15x10x10 cm of 1:3:6(1 cement: 3 coarse sand : 6 graded
stone aggregate 20 mm nominal size) or with wooden plugs and
screws or rawl plugs and screws or with fixing clips or with bolts and
nuts as required, including providing and fixing of glass panes with
glazing clips and special metal-sash putty of approved make
complete including applying a priming coat of approved steel primer;
excluding the cost of metal beading and other fitting except
10.12.1 Doors sqm 2843.00
10.13 Extra for providing and fixing steel beading of approved shape and
section with screws instread of glaxing clips and met. Sash putty in
steel doors, windows, Ventilators and comosite units.
10.13A Steel doors. sqm 278.00
10.13B Steel windows sqm 332.00
10.13C Steel ventilators sqm 338.80
10.14.1 Providing and fixing T-iron frames for doors. windows and ventilators kg 73.50
of mils steel Tee-sections, joints miltred and welded with 15x3 mm
lugs 10 cm long embedded in cement concerete blocks 15x10x10
cm of 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate
20 mm nominal size) or with wooden plugs and screws or rawl plugs
and screws or with fixing clips or with bolts and nuts as required
including
10.14.2 Fixing with carbon steel galvanised dash fastener of kg 70.90
required dia and size (to be paid for separately).
10.15 Providing and fixing pressed steel door confirming IS code 4351
manufactured from commerical mild steel sheet of 1.25 mm
thickness including hinges, jamb, lock jamb, bead and if required
angle threshold of mild steel angle of section 50 x 25 mm or base
ties of 1.25mm pressed mild steel welded or rigidly fixed together by
. mechnical means, adjustable lugs with split end tail to each jamb
including steel butt hinges 2.5 mm thick with mortar guards, lock
strike-plate and shock absorbers as specified and applying a coat of
approved steel primer after pre-treatment of the surface as directed
by Engineer-in-charge:
10.15.1 Profile B metre 365.10

BCD/SOR_8th Edition_October 2016 126

 Code
Description Unit Rate Rs.
No.
10.15 10.15.1 Profile B metre 365.10
10.15.2 Profile C metre 389.60
10.15.3 Profile E metre 426.20
10.16 Steel work in built up tubular trusses including cutting, hoisting, fixing
in position and applying a priming coar of approved steel primer,
welded and bolted including special shaped washers etc. complete:
10.16.1 Hot finished welded type tubes kg 92.30
10.16.2 Hot finished seamless type tubes kg 109.00
10.16.3 Electric resistance or induciton butt welded tubes kg 115.40
10.17 Providing and fixing M.S.fan clamp type I or II of 16 mm dia.M.S. bar each 97.00
bent to shape with hooked ends in R.C.C slabs during laying
including painting the exposed portion of loop,all as per standard
design complete.
10.17 Providing and fixing circular/hexagonal cast iron or M.S sheet box each 124.50
for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick
rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface
hacked for proper bonding top lid shall be screwed into the cast iron
box by means of 3.3 mm dia round headed screws, one lock at the
corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape
as per standard drawing.
10.19 Providing and fixing M.S. round holding down bolts with nuts and kg 73.60
washer plates complete.
10.20(a) providing and fixing bolts upto 300 mm in length kg 89.00
10.20(b) providing and fixing bolts above 300 mm in length kg 68.72
10.21 Providing and fixing M.S. rivets of sizes in position. kg 113.70
10.22(a) Welding by gas plant including tranportation of gas cm 3.00
10.22(b) Welding by electric plant incluidng transportation of electric welding cm 2.70
plant at site etc. complete.
10.28 Providing and fixing bright finished brass casement window fastners each 71.30
of minimum weight 200 gms to side hung steel windows with
necessary welding and machine screws etc. complete.
10.29 Providing and fixing bright finished brass peg stays 300 mm long of each 175.10
minimum weight 330 gms.to side hung steel windows with necessary
welding and machine screws etc. complete.
10.30 Providing and fixing bright finished brass peg stays to steel
ventilators with necessary welding and machine screws etc.
complete.
10.30.1 300 mm long of minimum weight of 330 grams. each 175.10
10.30.2 250 mm long of minimum weight of 240 grams. each 144.50
10.31 providing and fixing 14 mm bright finished brass each 223.90
10.32 Steel work welded in built up sections/framed worK including cutting
hoisting, rixing in position and applying a priming coat of approved
steel primer using structural steel, etc. as required.
10.32.1 In stringers, treads landings etc. of stair cases including use kg 66.10
of required plates wherever required all complete.
10.32.2 In gratings, frames, guard bar, ladders, railings, brackts. kg 76.70
gates & similar works.

127 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
10.33 Providing and fixing hand rail by welding etc. to steel ladder railings
& staircases railing including applying a priming coat of approved
steel primer
10.33.1 MS tube (medium) 40mm nominal bore kg 90.70
10.33.2 E.R.W tube 40 mm nominal dia kg 119.70
10.33.3 G.I pipes 40 mm nominal bore (class B) kg 102.40
10.33.4 Labour for fitting and fixing barbed wire fencing in six rows horizontal Per m 43.80
up to a height of 1.85m and two diagonals including fixing of post in
cement concrete at 2.5m centres including cost of staples (but
excluding the cost of cement concrete, angle, iron post, its cutting
and making holes, nuts & bolts) all complete as per building
specification and direction of E/l.
10.33.5 Labour for fitting and fixing barbed wire fencing in FOUR rows Per m 30.80
horizontal up to a height of 1.25m and two diagonals including fixing
of post in cement concrete at 2.5m centres including cost of staples
(but excluding the cost of cement concrete, angle, iron post, its
cutting and making holes, nuts & bolts) all complete as per building
specification and direction of E/l.
10.33.6 Drilling 6mm Dia. In M.S. angle iron for fixing of staples etc. as per Each 5.30
building specification and direction of E/l.
10.33.7 Labour for cutting of M.S. angle iron post to required length, one end Each 16.50
splitted as fish tailed in a length of 150mm complete as per building
specification and direction of E/l.
10.35 Providing and fixing carbon steel galvanised ( minimum coating 5
micron ) dash fastener of 10 mm dia double threaded 6.8 grade
(yield strength 480 N/mm2), counter sunk head, comprising of 10 m
dia polyamide PA 6 grade sleeve,including drilling of hole in frame ,
concrete/ masonry, etc. as per direction of Engineer-in-charge.
10.35.1 10 x60 mm. each 53.90
10.35.2 10 x80 mm. each 59.20
10.35.3 10 x120 mm. each 73.20
10.35.4 10 x140 mm. each 83.70
10.35.5 10 x160 mm. each 103.70
10.36 Providing and fixing stainless steel ( Grade 304) railing made of kg 623.90
Hollow tubes,channels, plates etc., including welding, grinding,
buffing, polishing and making curvature (wherever required) and
fitting the same with necessary stainless steel nuts and bolts
complete, i/c fixing the railing with necessary accessories & stainless
steel dash fasteners , stainless steel bolts etc., of required size, on
the top of the floor or the side of waist slab with suitable arrangement
as per approval of Engineer-in-charge, ( for payment purpose only
weight of stainless steel members shall be considered excluding
fixing accessories such as nuts, bolts,fasteners etc.).
10.37 Providing & fixing fly proof wire gauze to windows, clerestory
windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.
10.37.1 Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 sqm 341.70
mm aperture on both sides.
10.37.2 Stainless steel (grade 304) wire gauze of 0.5 mm dia wire sqm 984.40
and 1.4 mm aperture on both sides.

BCD/SOR_8th Edition_October 2016 128

Code
Description Unit Rate Rs.
No.
10.38 Providing & fixing glass panes with putty and glazing clips in steel
doors,windows, clerestory windows all complete with.
10.38.1 4.0 mm thick glass panes. sqm 741.70
10.38.2 5.5 mm thick glass panes. sqm 970.00
10.39 Providing and fixing factory made ISI marked steel glazed doors,
windows and ventilators, side / top / centre hung, with beading and
all members such as F7D,F4B, K11 B and K12 B etc. complete of
standard rolled steel sections, joints mitred and flash butt welded
and sash bars tenoned and riveted, including providing and fixing of
hinges, pivots, including priming coat of approved steel primer , but
excluding the cost of other fittings, complete all as per approved
design, (sectional weight of only steel members shall be measured
for payment).
10.39.1 Fixing with 15x3 mm lugs 10 cm long embedded in cement kg 101.30
concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3
coarse sand : 6 graded stone aggregate 20 mm nominal
size).
10.39.2 Fixing with carbon steel galvanised dash fastener of kg 71.60
required dia and size (to be paid for separately).
10.40 Extra for providing and fixing steel beading of size 10 x 10 x 1.6 mm metre 37.70
(box type),approved shape and section with screws instead of
glazing clips and metal sash putty, in steel doors, windows,
ventilators and composite units.
10.41 Providing and fixing M.S. Tubular frames for doors, windows,
ventilators and cupboard with rectangular/ L-Type sections, made of
1.60 mm thick M.S. Sheet,joints mitred, welded and grinded finish,
with profiles of required size, including fixing of necessary butt
hinges and screws and applying a priming coat of
10.41.1 Fixing with 15x3 mm lugs 10 cm long embedded in cement kg 212.30
concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3
coarse sand : 6 graded stone aggregate
10.41.2 Fixing with carbon steel galvanised dash fastener of kg 206.00
required dia and size (to be paid for separately).
10.42 Providing and fixing bolts including nuts and washers complete. kg 89.70
10.43 Providing and fixing concertina coil fencing with punched tape metre 289.50
concertina coil 600 mm dia 10 metre openable length ( total length
90 m), having 50 nos rounds per 6 metre length, upto 3 m height of
wall with existing angle iron ‘Y’ shaped placed 2.4 m or 3.00 m apart
and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with
G.I. staples and G.I. clips to retain horizontal, including necessary
bolts or G.I. barbed wire tied to angle iron, all complete as per
direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) /
Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq
mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of
M.S. angle, C.C. blocks shall be paid separately)

129 BCD/SOR_8th Edition_October 2016

SUB HEAD : 11.0
FLOORING
 BUILDING WORK - Contd.

11.0 Flooring
Code
Description Unit Rate Rs.
No.
11.1 Brick on edge flooring with bricks of class designation 100A including
cement slurry etc. complete in cement mortar.
11.1.1 1:4 (1 cement: 4 coarse sand) sqm 618.60
11.1.2 1:6(1 cement:6 coarse sand) sqm 577.30
11.3 Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone
agregate) finished with a floating coat of neat cement including cement
slurry, etc. but excluding the cost of nosing of steps etc. complete.
11.3.1 40 mm thick with 20 mm nominal size stone aggregate sqm 245.70
11.4 52 mm thick cement concrete flooring with metallic concrete hardener sqm 383.50
topping under layer 40 mm thick cement concrete 1:2:4(1 cement:2
coarse sand:4 graded stone aggregate 20 mm nominal size) and top
layer 12 mm thick metallic concrete hardener consisting of mix 1:2 (1
cement hardener mix:2 stone aggregate 6 mm nominal size) by volume
@ 2 liter per 50 kg of cement or as per manufacture specification. This
includes cost of cement slurry, etc. but excluding the cost of nosing of
steps etc. complete.
11.5 62 mm thick cement concrete flooring with metallic concrete hardener sqm 420.60
topping under layer 50 mm thick cement concrete 1:2:4(1 cement:2
coarse sand:4 graded stone aggregate 20 mm nominal size) and top
layer 12mm thick metallic cement hardener consisting of mix 1:2(1
cement hardener mix:2 stone aggregate 6 rnrr.. ominal size) by volume
hardning compound is mixed @ 2 liter per 50 kg of cement or as per
manufacture specification. This includes cost of cement slurry, etc. but
excluding the cost of nosing of steps etc. complete.
11.6 Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1
cement:3 coarse sand) finished with a floating coat of neat cement.
11.6.1 18 mm thick sqm 237.29
11.7 Cement concrete pavement with 1:2:4(1 cement:2 coarse sand:4 cum 4743.80
graded stone aggregate 20 mm nominal size) including finishing
complete.
11.8 Extra for making chequers of approved pattern on cement concrete sqm 22.00
floors, steps, landing, pavemerts etc.
11.9 40 mm thick marble chips flooring rubbed and polished to granolithic
finish, under layer 34 mm thick cement concrete 1:2:4(1 cement:2
coarse sand:4 graded stone aggregate 12.5 mm nominal size) and top
layer 6 mm thick with white, blacm, chocolate, grey, yellow or Baroda
green marble chips of sizes form 1 mm to 4 mm nominal size laid in
cement marble powder mix 3:1(3 cement: 1 marble powder) by weight
in proportion of 4:7 (4 cement marble powder mix:7 marble chips) by
volume including cement slurry etc. complete.
11.9.1 Dark shade pigment with ordinary cement sqm 446.60
11.9.2 Light shade pigment with white cement sqm 493.60
11.9.3 Medium shade pigment with 50% white cement and 50% sqm 470.10
ordinary cement.
11.9.4 White cement without any pigment sqm 475.90
11.9.5 Light shade pigment with ordinary cement. sqm 453.50
11.9.6 Ordinary cement without any pigment sqm 427.40

130 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
11.10 40 mm thick marble chips flooring, rubbed and polished to granolithic
finish, under layer 31 mm thick cement concrete 1:2:4(1 ement:2 oarse
sand:4 graded stone aggregate 12.5 mm nominal size) and top layer 9
mm thick with white, black.chocolate, grey, yellow or Baroda green
marble chips of sizes from 4 mm to 7 mm nominal size laid in cement
marble powder mix 3:1 (3 cement:1 marble powder) by weight in
proportion of 4:7( 4 cement marble powder mix:7 marble chips) by
volume including cement slurry etc. complete.
11.10.1 Dark shade pigment with ordinary cement sqm 461.60
11.10.2 Light shade pigment with white cement sqm 528.70
11.10.3 Medium shade pigment with 50% white cement and 50% sqm 495.20
ordinary cement
11.10.4 White cement without any pigment sqm 505.90
11.10.5 Light shade pigment with ordinary cement sqm 471.50
11.10.6 Ordinary cement without any pigment sqm 443.20
11.11 40 mm thick marble chips flooring,rubbed and polished to granolithic
finish, under layer 28 mm thick cement concrete 1:2:4(1 cement:2
coarse sand:4 graded stone aggregate 12.5 mm nominal size) and top
layre 12 mm thick with white, balck, chocoloate, grey, yellow or Baroda
gren marble chips of sizes for 7 mm to 10 mm nominal size laid in
cement marble powder mix 3:1(3 cement :1 marble powder mix
:3marble chips) by volume including cement slurry etc. complete.
11.11.1 Dark shade pigment with ordinary cement sqm 488.20
11.11.2 Light shade pigment with white cement sqm 582.20
11.11.3 Medium shade pigment with 50% white cement and 50% sqm 546.60
ordinary cement
11.11.4 White cement without any pigment sqm 542.90
11.11.5 Light shade pigment with ordinary cement sqm 580.90
11.11.6 Ordinary cement without any pigment sqm 462.70
11.12 Marble chips skirting (up to 30 cm height) rubbed and polished to
granolithic finish, top layer 6mm thick with white, black, chocolate, grey,
yellow or green marble chips of sizes from smallest to 4mm nominal
size laid in cement marble powder mix 3:1 (3 cement: 1 marble powder)
by weight in proportion of 4:7 94 cement marble poweder mix: 7 barbie
chips) by volume:
11.12.1 18 mm thick with under layer 12 mm thick in cement sqm 572.30
plaster 1:3 (1 cement : 3coarse sand).
11.12.2 21 mm thick with under layer 15 thick cement plaster 1:3(1
cement:3 coarse sand)
11.12.2.1 Dark shade pigment with ordinary cement sqm 584.40
11.12.2.2 Light shade pigment with white cement sqm 631.40
11.12.2.3 Medium shade pigment with 50 % white cement and 50% sqm 607.90
ordinary cement
11.18.2.4 White cement without any pigment sqm 588.10
11.12.2.5 Light shade pigment with ordinary cement sqm 591.30
11.12.2.6 Ordinary cement without any pigment sqm 603.60
11.13 Providing and fixing glass strips in joints of terrazo/cement concrete
floors.
11.13.1 40 mm wide and 4 mm thick meter 28.40

BCD/SOR_8th Edition_October 2016 131

Code
Description Unit Rate Rs.
No.
11.14 Extra for laying terrazo flooring on stair case treads not exceeding sqm 23.70
30cm in width including cost of forming, nosisng etc.
11.15 Crazy marble stone flooring, including filling the gaps with light shade
pigment with white cement marble powder mixture (3 parts of white
cement : 1 part of marble powder) by weight in proportion of 4:7 (4
cement marble powder mix : 7white, black or white and black marble
chips of sizes from 1 mm to 4 mm nominal size by volume), with under
layer 25 mm thick cement concrete 1:2:4 (1 cement :2 coarse sand : 4
graded stone aggregate 12.5 mm nominal size), including rubbing,
polishing and cement slurry etc. complete.
11.15.1 18 mm thick crazy marble stone white, black or as specified. sqm 760.20
11.16 Precast terrazo tiles 22 mm thick with marble chips of sizes upto 12
mm laid in floors and landings jointed with neat cement slurry mixed
with pigement to match the shade of the tiles; including rubbing and
polishing complete with precast tiles on 20 mm thick bed of cement
mortar 1:4(1 cement:4 coarse snad)
11.16.1 Light shade using white cement sqm 821.20
11.16.2 Medium shade using 50% white cement and 50% ordinary sqm 768.80
cement
11.16.3 Dark shade using ordinary cement sqm 636.20
11.16.4 Ordinary cement without any pigment sqm 604.60
11.17 Extra if terrazo tiles are laid in treads of steps not exceeding 30 cm in sqm 31.00
width
11.18 Precast terrazo tiles 22 mm thick with marble chips of sizes upto 12
mm in skirting and risers of steps not exceeding 30 cm in height, on 12
mm thick cement plaster 1:3 (1 cement:3 coarse sand) jointed with neat
cement slurry mixed with pigement to match the shade of the tiles,
including rubbing and polishing complete with tiles of
11.18.1 Light shade using white cement sqm 1008.00
11.18.2 Medium shade using 50% white cement and 50% ordinary sqm 937.70
cement
11.18.3 Dark shade using ordinary cement sqm 871.40
11.18.4 Ordinary cement without any pigment sqm 839.80
11.19 Chequered terrazo tiles 22 mm thick with marble chips of sozes upto 6
mm in floors jointed with neat cement slurry mixed with pigement to
match the shade of the tiles, including rubbing and polshing complete
on 20 nm thick bed of cement mortar 1:4 (1 cement:4 coarse sand)
11.19.1 Light shade using white cement sqm 908.50
11.19.2 Medium shade using 50% white cement and 50% ordinary sqm 829.30
11.19.3 Dark shade using ordinary cement sqm 752.50
11.19.4 Ordinary cement without pigment sqm 720.90
11.20 Chequerred precast cement concrete tiles 22 mm thick with marbie
chips of size 6 mm in footpath & coutyard jointed with neat cement
slurry mixed with pigment to match the shade of tiles including rubbing
and cleaning tec. Complete on 20 mm thick bed of cement mortar 1:4(1
cement:4 coarse sand)
11.20.1 Light shade using white cement sqm 1043.20

132 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
11.20 11.20.2 Medium shade using 50% white cement 50% grey cement sqm 861.70
11.20.3 Dark shade using ordinary cement sqm 642.00
11.20.4 Ordinary cement without any pigments sqm 610.30
11.21 Providing and fixing 10 mm thick acid and / or alkali resistant tiles of
approved make and colour using acid and / or alkali resisting mortar
bedding, and joints filled with acid and / or alkali resisting cement as per
IS : 4457, complete as per the direction of Engineer-in-Charge.
11.21.1 In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof
cement : 4 coarse sand).
11.21.1.1 Acid and alkali resistant tile. sqm 1189.50
11.21.2 In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof
cement : 4 coarse sand).
11.21.2.1 Acid and alkali resistant tile. sqm 1236.40
11.22 Tile work in skirting, risers of steps and dado(upto 2m height) over 12
mm thick bed of cement mortar 1:3(1 cement;3 coarse sand) and
jointed with grey cement slurry© 3.3 kg/sqm including pointing in .white
cement mixed with pigment of matching shade complete.
11.22.1 Marble tiles (polished) Raj nagar 8 mm thick sqm 1098.80
11.23 Marble stone flooring with 18 mm thick marble stone (sample of marble
shall be approved by Engineer-in-charge) over 20 mm (average) thick
base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed
with grey cement slurry including rubbing and polishing complete with:
11.23.1 Makrana white second quality. sqm 3169.40
11.23.2 Rajnagar plain white marble 18mm thick above 0.10 sqm sqm 1456.70
upto 0.20 sqm
11.23.2.1 Rajnagar plain white marble 18mm thick above 0.20 sqm sqm 1597.10
upto 0.50 sqm
11.23.4 :
Black Zebra marble . : sqm 1246.10
11.23.5 Udaipur green marble i sqm 1512.90
11.23.6 Pink marble sqm 1449.70
11.24 Extra for nosing in marble stone for treads sqm 185.80
11.25 Extra for marble stone flooring in treads of steps. Not exceeding 30 cm sqm 220.80
in width.
11.26 Kota stone slab flooring over 20 mm (average ) thick base laid over and
jointed with grey cement slurry mixed with pigment to match the shade
of the slab including rubbing and polishing complete . Base with 1:1:1
(1 lime : 1 surkhi: 1 coarse sand ) / 1:4 (1 cement: 4 coarse sand )
11.26.1 20 to 25 mm thick - sqm 998.30
11.27 Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillars sqm 973.00
laid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarse
sand ) and jointed with grey cement slurry mixed with pigment to match
the shade of the slab including rubbing and polishing complete. Details
of cost for 10 sqm
SAND STONE FLOORING
11.28 Supplying sand stone 40 mm thick for flooring ,carriage to site and
rough chisel dressing
11.28.1.1 Red sand stone sqm 287.30
11.28.1.2 white sand stone sqm 314.20

BCD/SOR_8th Edition_October 2016 133

 Code
Description Unit Rate Rs.
No.
11.28A. 40 mm thick rough chisel dressed stone flooring over 20 mm (average)
thick base with joint base 1:1:1 (1 lime : 1 Surkhi : 1 coarse sand) or 1:5
(1 cement : 5 coarse sand) finished flush.
11.28A.1 Red sand stone sqm 559.20
11.28A.2 White sand stone sqm 586.10
11.29 40 mm thick rough chisel dressed stone flooring over 20 mm (average)
thick base including pointing with C.M 1:2 (1 cement :2 stone dust) with
an admixture of pigment to match the shade of the stone with base
1:1:1 (1 lime : 1surkhi : coarse sand or 1:5 (1 cement : 5 coarse sand)
11.29.1 Red sand stone sqm 584.20
11.29.2 white sand stone sqm 611.10
11.30 40 mm thick fine dressed stone flooring over 20 mm (average) thick
base with joint finished flush:base 1:5 (1 cement: 5 coarse sand )
11.30.1 Red sand stone sqm 577.40
11.30.2 White sand Jtone sqm 604.20
11.31 Extra for pre finished nosing in treads of steps of Kota stone / sand m 49.00
stone slab.
11.32 Extra for Kota stone / sand stone in treads of steps and risers using sqm 10.70
single up to 1.05 metre.length
11.33 25 mm wooden planking, tongued and grooved in flooring including
fixing with iron screws complete .
11.33.2 2nd class teak wood sqm 3298.10
11.34 38 mm thick parquet (wood block) flooring of 1st class teak wood laid sqm 5974.00
over 25 mm thick levelling layer of cement concrete 1:2:4(1 cement:2
coarse sand:4 store aggregate 10 mm nominal size) to be paid
separately coated with a thin layer of hot bitumen (blown type) @ 2.45
kg per sqm. including fixing blocks in position after dipping in hot
bitumen (blown type) upto half depth,planed,levelled smooth and
finished complete.
11.35 Providing and fixing M.S. angle 50x50x5 mm to act as nosing with tugs kg 75.20
of M.S. flat 10x5 mm 10 cm long forked at end 60 cm apart (minimum 3
lugs to be provided) including necessary welding and applying a priming
coat of approved primer on exposed surfaces etc. complete
11.36 Providing and fixing 1st quality ceramic glazed wall tiles conforming to sqm 766.30
IS : 15622 (Thickness to be specified by the manufacture) of approved
make in all colours, shades except burgundy , bottle green , black of
any size as approved by Engineer-in-charge in skirting , risers of steps
and dados over 12 mm thick bed of cement Motar 1:3(1 cement: 3
coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm
including pointing in white cement mixed with pigment of matching
shade complete.
11.37 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness sqm 799.40
to be specified by the manufacturer) of ist quality conforming to IS :
15622 of approved make in colours such as white , Ivory , Grey , Fume
Red , Brown, laid on 20 mm thick Cement motar 1:4 (1 cement: 4
coarse sand) including pointing the joints with white cement and
matching pigment etc., complete.

134 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
11.38 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness sqm 812.20
to be specified by the manufacturer) of ist quality conforming to IS :
15622 of approved make in colours such shades except white , Ivory ,
Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1
cement: 4 coarse sand) including pointing the joints with white cement
and matching pigment etc., complete.
11.39 Providing and laying Ceramic glazed floor tiles 400x400 mm (thickness sqm 1226.50
to be specified by the manufacturer) of 1 st quality conforming to IS :
13755 of NITCO , ORIENT , SOMANY , KAJARIA or equivalent make
in colours such as white , Ivory , Grey , Fume , Red , Brown , laid on 20
mm thick cement motar 1:4 (1 cement: 4 Coarse sand) including
grouting the joints with white cement and matching pigments etc,
complete.
11.40. Providing and laying Ceramic glazed floor tiles 400x400 mm (thickness sqm 1264.90
to be specified by the manufacturer) of 1st quality conforming to IS :
13755 of NITCO , ORIENT , SOMANY , KAJARIA or equivalent make
in colours except white , Ivory , Grey , Fume , Red , Brown , laid on 20
mm thick cement motar 1:4 (1 cement: 4 Coarse sand) including
grouting the joints with white cement and matching pigments etc,
complete.
11.41 Providing and laying vitrifed floor tiles in different sizes {thickness to be
specified by the manufactruer) with water absorption's less than 0.08 %
and conforming to IS : 15622 of approved make in all colours and
shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse
sand ) including grouting the joint with white cement and matching
pigments etc., complete.
1.1.41.1 Size of Tile 50x50 cm. sqm 1521.30
11.41.2 Size of Tile 60x60 cm sqm 1694.30
11.41.3 Size of Tile 80x80 cm sqm 1957.10
11.41.4 Size of Tile 100x100 cm sqm 2681.20
11.42 Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 sqm 357.10
coarse sand) bedding in laying of floor tiles.
11.43 Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high sqm 359.4
polymer modified quick-set tile adhesive (Water based) conforming to
IS: 15477, in average 3 mm thickness.
11.44 Crazy ceramic tile flooring, with under layer 12 mm thick cement mortar sqm 322.1
1:4 (1 cement: 4 coarse sand), with joints not exceeding 5 mm,
including filling the gaps with ordinary cement mixture & mixing with
synthetic polyester fibre, triangular in shape having specific gravity of
1.34 to 1.40, cross section size ranging from 10 to 40 micron & length
upto 6 mm , mixing fibre @ 125 grams per 50 kg of cement in cement
mortar, including providing and mixing water proofing material in
mortar @ 1 kg per 50 kg of cement , all complete as per direction of
Engineer-in-charge.
11.45 Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) sqm 1550.1
on 150 mm thick sub grade of compacted bed of 20 mm thick nominal
size stone aggregate and base course and filling with 150 mm thick
jamuna sand, including spreading, well ramming, consolidating and
finishing smooth etc. all complete as per direction of Engineer-in-
charge.

BCD/SOR_8th Edition_October 2016 135

Code
Description Unit Rate Rs.
No.
11.46 Providing and laying Vitrified tiles in different sizes (thickness to be
specified by manufacturer), with water absorption less than 0.08 % and
conforming to I.S. 15622, of approved make, in all colours & shade, in
skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1
cement: 3 coarse sand), including grouting the joint with white cement
& matching pigments etc. complete.
11.46.1 Size of Tile 500 x 500 mm. sqm 1234.7
11.46.2 Size of Tile 600 x 600 mm. sqm 1403.6
11.46.3 Size of Tile 800 x 800 mm. sqm 1660.1
11.46.4 Size of Tile 1000 x 1000 mm. sqm 2367
11.47 Providing and laying Vitrified tiles in different sizes (thickness to be
specified by the manufacturer), with water absorption less than 0.08%
and conforming to IS: 15622, of approved brand & manufacturer, in all
colours and shade, in skirting, riser of steps, laid with cement based
high polymer modified quick set tile adhesive (water based) conforming
to IS: 15477, in average 6 mm thickness, including grouting of joints
(Payment for grouting of joints to be made separately).
11.47.1 Size of Tile 500 x 500 mm. sqm 1417.8
11.47.2 Size of Tile 600 x 600 mm. sqm 1586.7
11.47.3 Size of Tile 800 x 800 mm. sqm 1843.2
11.47.4 Size of Tile 1000 x 1000 mm. sqm 2550.2
11.48 Grouting the joints of flooring tiles having joints of 3 mm width, using
epoxy grout mix of 0.70 kg of organic coated filler of desired shade
(0.10 kg of hardener and 0.20 kg of resin per kg), including filling/
grouting and finishing complete as per direction of Engineer-in-charge.
11.48.1 Size of Tile 500x500 mm. sqm 199.40
11.48.2 Size of Tile 600 x 600 mm. sqm 169.00
11.48.3 Size of Tile 800 x 800 mm. sqm 138.70
11.48.4 Size of Tile 1000 x 1000 mm. sqm 102.10
11.49 Providing and laying Vitrified tiles in floor with different sizes (thickness
to be specified by the manufacturer), with water absorption less than
0.08% and conforming to IS:15622 , of approved brand &
manufacturer, in all colours and shade, laid with cement based high
polymer modified quick set tile adhesive (water based) conforming to IS
: 15477, in average 6 mm thickness, including grouting of joints
(Payment for grouting of joints to be made separately).
11.49.1 Size of Tile 500 x 500 mm. sqm 1375.90
11.49.2 Size of Tile 600 x 600 mm. sqm 1544.80
11.49.3 Size of Tile 800 x 800 mm. sqm 1801.30
11.49.4 Size of Tile 1000 x 1000 mm. sqm 2508.20
11.50 Deduct for not grouting the joints with white cement and matching sqm 8.50
pigment in the items of fixing of vitrified tiles.

136 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
11.51 Providing and laying machine cut, mirror polished, Italian Marble stone
flooring laid in required pattern in linear portion of the building all
complete as per architectural drawings, with 18 mm thick stone slab
laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement :
4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm
including pointing with white cement slurry admixed with pigment to
match the marble shade including rubbing, curing and polishing etc. all
complete as specified and as directed by the Engineer-in-Charge.
a. 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire sqm 5245.90
Red or Dark Emperadore etc.
11.52 Providing and laying machine cut, mirror polished Marble stone flooring,
in required design (Simple geometrical, abstract etc.) and in patterns in
combination with Italian marble stones of different colours, shades and
finished surface texture etc., in linear portions of the building, all
complete as per the shades and finished surface texture etc., in linear
portions of the building, all complete as per the architectural drawings,
with 18 mm thick stone slab laid over 20 mm (average) thick base of
cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with
white cement slurry @ 4.4 kg/sqm including pointing with white cement
slurry admixed with pigment to match the marble shade including
rubbing , curing and polishing etc. all complete as specified and as
directed by the Engineer-in-Charge.
a. 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire sqm 5473.20
Red or Dark Emperadore etc.
11.53 Providing and fixing Glass mossaic tiles at finished plain wall surface of sqm 1615.60
size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize
design as per direction of Engineer-in- Charge. The glass mosaic tiles
to be fixed on the wall surface with the help of approved adhesive
applied at the rate of 2.5 kg per sqm and grouting of the same. The
rate is inclusive of all operation, material and required pattern approved
by Engineer-in-Charge.
11.54 Providing and fixing removable raised/false access flooring with system
and its components of approved make for different plenum height with
possible height adjustment upto 50 mm, comprising of modular load
bearing floor panels supported on G.I. rectangular stinger frame work
and G.I. Pedestal etc. all complete, as per the architectural drawings,
as specified and as directed by Engineer-in-charge consisting of :
a) P roviding at required spacing to form modular framework, pedestals
made out of GI tube of thickness minimum 2 mm and 25 mm outer
diameter, fully welded on to the G.I. Base plate of size
100mmx100mmx3mm at the bottom of the pedestal tube, G.I. pedestal
head of size 75mmx75mmx3.5 mm welded with GI fullythreaded stud
16mm outer diameter with two GI Check nuts screwed on the stud for
level adjustment upto 50mm, locking and stabilizing the pedestal head
in for level adjustment upto 50mm, locking and stabilizing the pedestal
head in position at the required level. The pedestals shall be fixed to
the subfloor (base)through base plate using epoxy based adhesive of
approved make or the machine through base plate using epoxy based
adhesive of approved make or the machine screw with rawl plug.

BCD/SOR_8th Edition_October 2016 137

Code
Description Unit Rate Rs.
No.
11.54 b) S tringers system in all steel construction hot dipped galvanized of
rectangular size 570x20x30x0.80 mm thick having holes at both ends
for securing the stringers on to the pedestal head using fully threaded
screws ensuring maximum lateral stability in all directions, the grid
formed by the pedestal and stringer assembly shall receive the floor
panel, this system shall provide adequate solid,rigid support for access
floor panel, the system shall provide a minimum clear uninterrupted
clearance between the bottom of the floor for electrical conduits and
wiring etc. all complete as per the architectural drawings, as specified
and as directed by the Engineer-in-charge.
c) providing and fixing Access Floor panel of 600x600x32 mm medium
grade Filled Steel anti static high pressure Lamination of 800H grade
(FS800H). Access Floor panel shall finished with Anti-static High
Pressure laminate with Non Warp technology uptobe steel welded
construction with an enclosed bottom pan with uniform pattern of 64
hemispherical cones. The top and bottom plates of Steel Gauges: top
0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64
welds in each dome and 20 welds along each flange). The panel should
be Corroresist epoxy coated for lifetime rust protection and cavity
formed by the top and bottom plate is filled with Pyrogrip
noncombustible Portland cementitious core mixed with lightweight
foaming compound. The access floor shall be factory core mixed with
lightweight foaming compound. The access floor shall be factory 1mm
thickness for superior adhesion and Surface flatness within
0.75mm.The panel is to withstand a Concentrated Load of 363 kgs
applied on area 25mm x 25mm The panel will withstand and Uniformly
Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of
50kg all complete as per the approved manufacturers specification and
as per the direction of Engineer-in-charge. All specification must be
printed on the side of the panel to ensure the quality of the product.
11.54.1 300 mm Finished Floor Height (FFH). sqm 4182.20
11.54.2 450 mm Finished Floor Height (FFH). sqm 4182.20
11.72 Providing designation 100 A one brick flat soling joints filled with local sqm 253.80
sand including cost of watering, taxes, royalty all complete as per
building specification and direction of E/l,
11.73 Providing designation 100 A one brick on edge soling joints filled with sqm 407.00
local sand including cost of watering, taxes, royalty all complete as per
building specification and direction of E/l,
11.74 Providing designation 100 B one brick flat soling joints filled with local sqm 235.60
sand including cost of watering, taxes, royalty all complete as per
building specification and direction of E/l, but excluding carriage cost of
bricks & sand.
11.75 Providing designation 100 B one brick on edge soling joints filled with sqm 376.80
local sand including cost of watering, taxes, royalty all complete as per
building specification and direction of E/l,
11.76 Providing average 150mm thick dry rammed khoa beaten to 112mm sqm 329.90
(compacted with water) made of well burnt or jhama bricks including
ramming properly till compacted thickness is achieved, curing and
carriage of water with all leads, making proper slope and blinding the
top with cement mortar (1: 10) all complete as per building specification
and direction of E/l,

138 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
11.77 Providing and laying 60 mm thick factory made cement concrete sqm 475.40
interlocking paver block of M -30 grade made by block making machine
with strong vibratory compaction, of approved size, design & shape, laid
in required colour and pattern over and including 50 mm thick
compacted bed of coarse sand, filling the joints with fine sand etc. all
complete as per the direction of Engineer-in-charge.
11.78 Providing and laying factory made coloured chamfered edge Cement sqm 690.70
Concrete paver blocks of required strength, thickness & size/shape,
made by table vibratory method using PU mould, laid in required colour
& pattern over 50mm thick compacted bed of fine sand, compacting
and proper embedding/laying of inter locking paver blocks into the sand
bedding layer through vibratory compaction by using plate vibrator,
filling the joints with jamuna sand and cutting of paver blocks as per
required size and pattern,finishing and sweeping extra sand in footpath,
parks, lawns, drive ways or light traffic parking etc.complete as per
manufacturer’s specifications & direction of Engineer-in-Charge.
60mm thick C.C.paver block of M-35 grade with approved colour,
design & pattern.
11.79 Providing and laying factory made chamfered edge Cement Concrete
paver blocks of required strength,thickness & size/shape, made by
table vibratory method , to attain superior smooth finish using PU or
equivalent moulds, laid in required Grey colour & pattern over 50mm
thick compacted bed of coarse sand, compacting and proper
embedding / laying of inter locking paver blocks into the sand bedding
layer through vibratory compaction by using plate vibrator, filling the
joints with jamuna sand and cutting of paver blocks as per required size
and pattern, finishing and sweeping extra sand in footpath, parks,lawns,
drive ways or light traffic parking etc. all complete as per
manufacturer’s specifications & direction of Engineer -in-Charge:

11.79.1 (a) 80 mm thick c.c. paver block of M-35 grade with sqm 763.40
approved colour design and pattern.
11.79.2 (b) 80 mm thick c.c. paver block of M-35 grade with sqm 722.60
white colour design and pattern.

BCD/SOR_8th Edition_October 2016 139

SUB HEAD : 12.0
ROOFING
 BASIC RATES - Contd.

12.0 Roofing
Code
Description Unit Rate Rs.
No.
12.1 Providing corrugated G.S. sheet roofing fixed with G.I.J. or hooks, bolts and
nuts 8 mm diameter with bitumen and G. I. limpet washers or with G.I. limpet
washers filled with white lead and including a coat of approved steel primer
and two coats of approved paint on over lapping of sheets complete (upto a
pitch of 60°) excluding the cost or purlins, rafters and trusses.
12.1.3 1.00 mm thick with zinc coating not less than 275 gm/m z sqm 859.80
12.1.4 0.8mm thick with zinc coating not less than 275 gm/m z sqm 729.70
12.1.5 0.63 mm thick with zinc coating not less than 275 gm/m 2 sqm 618.80
12.2 Extra for providing and fixing corrugated G. S. sheets vertically or to a pitch sqm 6.50
exceeding 60
12.3 Extra for providing and fixing curved C.G.S. sheets on roofing
12.3.4 0.80 mm thick sqm 7.40
12.3.5 0.63 mm thick sqm 6.00
12.4 Extra for straight cutting in C.G. S. sheet roofing for making opening of area
exceeding 40 dm2 for chimney stacks , sky light etc.
12.4.3 1.00 mm thick m 28.50
12.4.4 0.80 mm thick m 22.80
12.4.5 0.63 mm thick m 22.80
12.5 Extra for circular cutting in C. G. S. sheet roofing for making opening of
area exceeding 40 square decimeter .
12.5.3 1.0 mm thick m 161.50
12.5.4 0.80 mm thick m 129.00
12.5.5 0.63 mm thick m 129.00
12.6 Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed
with G.I.J. or L hooks . Bolts and nuts 8 mm dia. G. 1. limpet and bitumen
washers complete. .
12.6.1 0.80 mm thick with zinc coating not less than 275 gm/m 2 m 499.90
Consider the length of the ridge 10.35 metres. The ridge will be
made out of plain G. I. sheets 0.9 m x 1.8 m ,
2
12.6.2 0.63 mm thick with zinc coating not less than 275 gm/m m 432.40
12.7 Providing valleys of 90 cm wide overall in plain G.S. sheet fixed with G.I.J. or
L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers
complete.
12.7.1 1.60 mm thick with zinc coating not less than 350 gm/m z m 982.20
12.8 Providing flashing of 40 cm over al width in plain, G.S. sheet fixed with G.I.J.
or L. hooks, bolts and nuts G.I. limpet and bitumen washers complete, bent
to shape and fixed in wall with cement mortar 1:3(1 cement:3 coarse sand).
12.8.2 1.00 mm thick with zinc coating not less than 275 gm/m 3 m 359.00
12.9 Providing and fixing 15 cm wide 45 cm over all semi circular plain G.S. sheet
gutter with iron brackets 40x3 mm size bolts, nuts and washers etc. including
making necessary connections with rain water pipes complete.
12.9.3 0.80 mm thick with zinc coating not less than 275 gm/m 2 m 463.70
12.9.4 0.63 mm thick with zinc coating not less than 275 gm/m 2 consider m 407.50
a length of 9.04 metres.

140
Code
Description Unit Rate Rs.
No.
12.10 Providing asbestos cement 6 mm thick corrugated sheets roofing and fixing
with G.I. J or L hooks bolts and nuts 8 mm dia G. I. plain and bitumen
washers complete excluding the cost or purlins, rafters and trusses
corrugated sheet.
12.10.1 upto 60 degree pitch sqm 328.40
12.10.2 above 60 degree pitch sqm 335.20
12.11 Extra for straight cutting in A.C. corrugated, semi corrugated 6 mm thick m 22.80
2
sheet roofing for making opening of area exceeding 40 dm for chimney
stacks, skylights etc.
12.12 Extra for circular cutting in A.C. corrugated/semi corrugated 6 mm thick m 189.70
2
sheet roofing for making opening of area exceeding 40 dm
12.13 Extra for providing and fixing wind ties of 40x6mm flat iron section. m 113.20
12.14 Providing and fixing ridges and hips in asbestos cement sheet roofing
12.14.1 One piece plain angular ridges Consider a shed of 20x 10 m m 210.80
(external dimensions at plinth )
12.14.2 Serrated of plain wing adjustable ridges Consider a shed of 20x10 m 277.70
m ( external dimension at plinth)
12.14.3 Close fitting adjustable ridges consider a shed 20x10 metre m 355.50
(External dimension at plinth).
12.14.5 Unserrated adjustable hips consider a shed with hip as 20.2 m 277.30
metres.
12.15 Providing and fixing asbestos cement roofing accessories with galvanised
iron J or L hooks, bplts and nuts and of G.l. seam bolts and nuts. G.I. plain
and bitumen washers complete.
12.15.1 Approan flashing pieces m 198.10
12.15.2 Eves filler pieces m 148.80
12.15.3 North light and ventilator curves m 367.90
12.15.4 Barge boards . m 237.40
12.15.6 Ridge finials pair 143.70
12.15.8 Curved barge boards for north light curves each 265.70
12.15.9 Roof lights each 1429.40
12.15.10 Expansion joints for ridges each 427.00
12.15.11 Expansion joints fosr north light curves each 351.30
12.15.12 S type louvers m 141.40
12.20 Providing flat iron brackets 50x3mm size, with necessary bolts, nuts and m 62.00
washers etc.for fixing asbestos cement /G.S sheet gutters with purlins.
12.29 Painting top of roofs with bitumen of approved quality at 17 kg per 10m2
2
impregnated with a coat of coarse sand at 60 cubic dm per 10m including
cleaning the slab surface with brushes and finally with a piece of cloth lightly
soaked in kerosene oil complete:
12.29.1 With residual type petroleum bitumen of VG10 sqm 110.50
12.33 Providing and laying brick tiles of class designation 100 over mumty root
grouted with cement mortar 1:3 (1 cement:3 coarse sand) mixed with 2% if
integral water proofing compound by weight of cement, over a 12 mm layer
of cement mortar 1:3 (1 cement:3 fine sand) and finished neat.
12.33.2 With F.P. brick tiles sqm 436.00

141
Code
Description Unit Rate Rs.
No.
12.3 12.33A Providing and laying pressed clay tiles (as per approved pattern 20 sqm 515.00
mm nominal thickness and of approved size) on roofs jointed with
cement mortar 1:4(1 cement :4 coarse sand )mixed with 2%
integral water proofing compound laid over a bed of 20 mm thick
cement mortar 1:4(1 cement::4 coarse sand )and finished neat
complete
12.38 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement:2 coarse sand:4
stone aggregate 10mm and down gauge) including finishing with cement
mortar 1:3(1 cement::3 coarse sand)as per standard design
12.38.1 In 75x75 mm deep chase sqm 94.70
12.39 Making khurras 45x45 cm with average minimum thickness of 5 cm cement each 150.10
concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm
nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement
plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the
edges and making and finishing the outlet complete
12.40 Providing sand stone slabs for roofing and laying them in cement mortar 1:4 (1
cement:4 coarse sand) over wooden karries or R.C.C. battens (karries and
battens to be paid separately) including pointing the ceiling joints with cement
mortar 1:3 (1 cement:3 coarse sand) complete:
12.40.1 Red sand stcne slab
12.40.1.1 40 mm thick sqm 376.00
12.40.1.2 45mm thick sqm 393.60
12.40.1:3 50 mm thick sqm 411.30
12.40.2 White sand stone slab
12.40.2.1 40 mm thick ,. sqm 447.20
12.40.2.2 45 mm thick sqm 464.70
12.40.2.3 50 mm thick sqm 482.50
12.52 Grading roof for water proofing treatment with
12.52.2 Cement concrete 1:2:4(1 cement :2 coarse sand : 4 graded stone cum 3732.90
aggregate 20 mm nominal size)
12.52.3 Cement mortar 1:3(1 cement:3 coarse sand) cum 6473.00
12.52.4 Cement mortar 1:4 (1 cement: 4 coarse sand) cum 5537.30
12.54 Providing and fixing 20 mm thick wooden planks ceiling (frame work for base
to be paid separately) with M.S screws:
12.54.1 2nd class teak wood sqm 1954.70
12.54.3 1st class kail wood sqm 890.80
12.55 Providing and fixing insulating board ceiling of approved quality with necessary
nails etc complete (frame work to be paid separately)
12.55.1 Natural colour insulating board
12.55.1.1 12 mm thick sqm 514.70
12.55.2 White face insulating board
12.55.2.1 12 mm thick sqm 624.30
12.55.3 Flame retardant face insulating board
12.55.3.1 12mm thick sqm 575.10
12.56 Providing and fixing hard board sheet ceiling of approved quality with
necessary nails etc complete (frame work to be paid separately)
12.56.1 Standard quality boards
12.56.1.1 3 mm thick sqm 306.10
12.56.1.2 4.5 mm thick sqm 339.80

142
 Code
Description Unit Rate Rs.
No.
12.57 Providing and fixing flat pressed 3 layer medium density particle board sheet
Grade I conforming to IS: 3087 in ceiling with necessary nails etc. complete
(frame work to be paid separately).
12.57.2 12 mm thick sqm 588.20
12.58 Providing and fixing plain A.C. sheet ceiling of approved quality with necessary
nails etc. complete (frame work to be paid separately):
12.58.2 6 mm thick sqm 384.40
12.59 Extra for circular cutting and waste in ceiling with
12.59.1 2nd class teak wood planks 20 mm thick m 335.00
12.59.4 Natural colour insulating board
12.59.4.1 12 mm thick m 153.50
12.59.5 White face insulating board
12.59.5.1 12 mm thick m 168.50
12.59.6 Flame retardant face insulating board
12.59.6.1 12 mm thick . . m 161.00
12.59.7 Standard quality hard board sheet
12.59.7.1 3 mm thick m 129.20
12.59.7.2 4.5 mm thick m 133.40
12.60 Extra for providing and fixing ceiling to curved surfaces in narrow widths sqm 110.30
12.60A Providing and fixing false ceiling with 12 mm thick plain/or with design ceiling sqm 591.10
tiles of BWP type phenol formaldehyde synthetic resin bonded pressed particle
board conforming to IS :3087 finished with a coat of aluminum primer on both
sides & edges and two coats of synthetic enamel paint of approved quality on
exposed face fixed to a grid made out of anodized aluminum (with 15 micron
anodic coating) T-sections 35x15x1.5 mm size main runners and cross
runners 23.5x19x1.5 mm fixed to main runners placed 600 mm centre to
centre both ways so as to form a grid of 600 mm square. The frame work shall
be suspended from ceiling by level adjusting hangers of 6 mm dia M.S. rod
fixed to roof slab ny means of ceiling cleats. The suspenders shall be placed
600x1200 mm centre to centre including fixing to the frame with CP brass
screws and applying a priming coat of zinc chromate yellow primer for steel
members complete (Frame work and suspenders to be paid for separately)
12.60C Extra for providing 3 mm thick translucent white acrylic plastic sheets of sqm 378.40
approved quality in false ceiling instead of 12 mm thick plain/or with design
particle board ceiling tiles in item above.
12.61 Providing 10 mm thick plaster of Paris (Gypsum anhydrous) ceiling upto a
height of 5 m above floor level over first class kail wood strips 25x6x mm with
10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden
frame (frame work to be paid separately)
12.61.1 Flat surfaces sqm 670.00
12.61.2 Curved surfaces sqm 755.40
12.62 Extra for any sunk or raised moldings in the plaster of Paris (Gypsum sqm 178.10
anhydrous) ceiling
12.63 Extra for providing plaster of Paris (Gypsum anhydrous) ceiling above 5 sqm 66.40
metres height from floor level.
12.64 Providing and fixing 12 mm thick plaster of pairs (Gypsum anhydrous) ceiling sqm 413.70
tiles upto a height of 5 metres above floor level over wooden frames and
rendered smooth with plaster of pans (frame work to be paid separately).

BCD/SOR_8th Edition_October 2016 143

Code
Description Unit Rate Rs.
No.
12.65 Extra for providing and fixing plaster of Paris (Gypsum anhydrous) ceiling tiles sqm 31.20
beyond 5 metres height form floor level.(Height beyond 5 m to be measured
for extra payment)
12.67 Extra for making chamfered edges of beading
12.67A Thermal Insulation of roofing with bonded mineral wool, laid over sqm 245.40
false ceiling with suitable adhesive as per directions of the
Engineer -in-charge.
12.67B Thermal Insulation of roofing with Expanded polystyrene fixed with
suitable adhesive to the false ceiling as per the directions of the
Engineer-in charge
12.67B.1 With Type N-Normal sqm 304.20
12.67B.2 With Type SE Self Extinguishing type sqm 304.20
12.68 Providing and fixing 100 mm diameter and 60 cm long rain water spout in
cement mortar 1:4 (1 cement :4 fine sand)
12.68.1 Stone ware spout spout 70.80
12.68.2 Cement concrete spout spout 70.80
12.71 Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I
rain water pipes embedded in and including cement concrete blocks 10x10x10
cm of 1:2:4 mix(1ceme.it:2coarse sand:4 graded stone aggregate 20 mm
nominal size) and cost of cutting holes and making good the walls etc.
12.71.1 75 mm diameter each 108.30
12.71.2 100 mm diameter ; each 105.90
12.71.3 150 mm diameter . . . . each 112.00
12.73 Providing lead caulked joints to sand cast iron rain water pipes and fittings:
12.73.1 75 mm dia pipe each 134.80
12.73.2 100 mm dia pipe each 173.40
12.73.3 150 mm dia pipe each 242.90
12.74 Providing and embedding sand cast iron accessories for rain water pipes in the
masonry surrounded with 12 mm thick cement mortar of the same mix, as that
of masonry (lead caulking will be paid for separately):
12.74.2 Sand cast iron plain shoes
12.74.2.3 150 mm diameter shoe 296.30
12.78 Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per
sqm) rain water pipes conforming to IS :4985 including jointing with seal ring
conforming to IS: 5382 leaving 10 mm gap for thermal expansion.
12.78.1 75 mm diameter metre 127.30
12.78.2 110 mm diameter metre 212.40
12.79 Providing and fixing on wall face unplasticised -PVC molded
fittings/accessories for unplasticised-PVC rain water pipes conforming to
(S:4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm
gap for thermal expansion.
12.79.1 Coupler
12.79.1.1 75 mm each 105.50
12.79.1.2 110mm each 140.20
12.79.2.1 Single pushfit coupler
12.79.2.1 75 mm each 125.10
12.79.2.2 110 mm each 175.60
12.79.3 Single tee with door

144 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
12.79 12.79.3.1 75x75x75 mm each 221.20
12.79.3.2 110x110x110mm each 306.10
12.79.4 Single tee without door
12.79.4.1 75x75x75mm each 196.80
12.79.4.2 110x110x110 mm each 257.30
12.79.5 Band 87.50
12.79.5.1 75 mm bend each 112.90
12.79.5.2 110 mm bend each 168.30
12.79.6 Shoe plain
12.79.6.1 75 mm shoe each 175.10
12.79.6.2 110m Shoe each 305.02
12.80 Providing and fixing unplasticised -PVC pipe clip of approved design to
unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs,
screwed with M.S. screws of required length including cutting brick work and
fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall
etc complete
12.80.1 75 mm each 126.20
12.80.2 110 mm each 144.49
12.81 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 each 39.10
cm diameter and weighing not less than 440 grams.
12.82 Providing and fixing at all height false ceiling of 12.5 mm thick -tapered edge SQM 768.50
gypsum board conforming to IS : 2095 including -providing and fixing of
frame work made of special sections power pressed from M.S. sheet and
galvanized in accordance with zinc coating 120gm/sqm as per IS : 277 and
consisting of angle cleats of size 25 mm wide x 16 mm thick with flanges of 22
mm and 27 mm at 1200 mm centre to centre one flange fixed to the ceiling
with dash fastener 12.5 mm dia x 40 mm long with 6 mm dia bots to the angle
hangers of 25x10x0.5 mm of required length, and other end of angle hanger
being fixed with nut and bots to rate of 1200 mm centre to centre to which the
ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of
26 mm each having clips of 10.5 mm at 450 mm centre to centre shall be be
fixed in a direction perpendicular to G. I. channel with connecting clips made
out of 2.64 mm dia x 230 mm long G. I. wire at every junction including fixing
the gypsum board with ceiling section and perimeter channels 0.5 mm thick 27
mm high having flanges of 20 mm and 30 mm long . the perimeter of ceiling
fixed to wall / partition with the help of rawl plugs at 450 mm centre to centre
with 25 mm long dirve-all screws @ 230 mm interval including jointing and
fixing to a flush of tapered and square edges of the gypsum board with
recommended filler., paper tapes, finisher and two coats of primer suitable for
gypsum board as per manufactures specification and also including the coat
cutouts made with frame of perimeter channels suitably fixed all complete as
per- drawing and specification and direction of the Engineer-in-Charge but
excluding the cost of painting.

BCD/SOR_8th Edition_October 2016 145

Code
Description Unit Rate Rs.
No.
12.45 Providing and fixing false ceiling at all height including providing and fixing of
frame work made of special sections, power pressed from M.S. sheets and
galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS :
277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with
flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to
the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts,
other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required
length with nuts & bolts of required size and other end of angle hanger fixed
with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200
mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge
of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450
mm centre to centre, shall be fixed in a direction perpendicular to G.I.
intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm
long G.I. wire at every junction, including fixing perimeter channels 0.5 mm
thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of
ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with
25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum
board to ceiling section and perimeter channel with the help of dry wall screws
of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush
finish of tapered and square edges of the board with recommended jointing
compound , jointing tapes , finishing with jointing compound in 3 layers
covering upto 150 mm on both sides of joint and two coats of primer suitable
for board, all as per manufacturer’s specification and also including the cost of
making openings for light fittings, grills, diffusers, cutoutsmade with frame of
perimeter channels suitably fixed, all complete as per drawings, specification
and direction of the Engineer in Charge but excluding the cost of painting with :
12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: SQM 745.60
2095- Part I
12.45.2 12.5 mm thick tapered edge gypsum fire resistant board SQM 792.60
conforming to IS: 2095- Part I
12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board SQM 813.90

12.45.4 Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 SQM 1646.40
mm having approx. 15 % perforated area with perforation size and
pattern as approved by the Engineer-in-charge and as per
manufacturer’s specification, with all 4 side tapered and backed by
acoustical tissue with NRC value not less than 0.60.

146 BCD/SOR_8th Edition_October 2016

SUB HEAD : 13.0
FINISHING
 BASIC RATES - Contd.

13.0 Finishing
Code
Description Unit Rate Rs.
No.
Cement plaster in course sand
13.11 12 mm cement plaster of mix:
13.11.1 1:3 (1 cement:3 coarse sand) sqm 128.20
13.11.2 1:4(1 cement :4 coarse sand) sqm 114.70
13.11.3 1:5(1 cement: 5 coarse sand) sqm 107.40
13.11.4 1:6(1 cement: 6 coarse sand) sqm 101.20
13.12 15 mm cement plaster on rough side of single or half brick wall
of mix.
13.12.1 1:3 (1 cement :3 coarse sand) sqm 149.20
13.12.2 1:4(1 cement: 4 coarse sand ) sqm 133.20
13.12.3 1:5 (1 cement: 5 coarse sand) sqm 124.50
13.12.4 1:6 (1 cement: 6 coarse sand) sqm 117.10
13.13 20 mm cement plaster of mix ;
13.13.1 1:3 (1 cement: 3 coarse sand) sqm 182.30
13.13.2 1: 4(1 cement: 4 coarse sand) sqm 161.30
13.13.3 1:5(1 cement: 5 coarse sand) sqm 150.10
13.13.4 1:6(1 cement: 6 coarse sand) sqm 140.40
13.14 12 mm lime plaster of mix:
13.14.1 1:1:1 (1 lime putty:1 surkhi:1sand ) sqm 103.90
13.14.2 1:1:2(1 limeputty :1surkhi:2 sand) sqm 97.10
13.14.3 1:2(1 lime: 2surkhi) sqm 117.40
13.14.4 1:3(1lime putty: 3surkhi) sqm 117.20
CEMENT PLASTER WITH A FLOATING COAT OF NEAT
CEMENT
13.17.1 12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished sqm 159.00
with a floating coat of near cement
13.17.2 12 mm cement plaster 1:4( 1 cement: 4coarse sand) finished with sqm 145.50
a floating coat of near cement Details of cost for 10 sqm
13.18 15 mm cement plaster 1:3 (1 cement: 3 coarse sand ) finished sqm 180.10
with a floating coat of neat cement on the rough side of single or
half brick wall.
13.19 18 mm cement plaster in two coat under layer 12 mm thick sqm 158.10
cement plaster 1:5 (1 cement: 5 course sand) and a top layer
6mm thick cement plaster 1:3(1 cement: 3 coarse sand finiished
rough with sponge
13.20 18 mm cement plaster in two coats under layer 12 mm thick sqm 170.00
cement plaster 1:5 (1 cement :5 coarse sand) and top layer 6 mm
thick, cement plaster 1:3 (1 cement: 3 coarse sand) finished
rough with sponge.
13.24 6 mm cement plaster to ceiling of mix :
13.24.1 1:3(1 cement: 3 coarse sand) sqm 94.10
13.24.2 1:4(1 cement: 4 coarse sand) sqm 87.40
13.26 Neat cement punning sqm 32.30

147 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
13.30 Rough cast plaster upto 10m night above ground level with a mixture
of sand and gravel or crushed stone from 6 mm to 10 mm nominal
size dashed over and including the fresh plaster in two layers, under
layer 12 mm cement plaster 1:4(1 cement :4 coarse sand) and top
layer 10 mm cement plaster 1:3 (1 cement :3 course sand) mixed
with 10% finely grounded hydrated lime by volume of cement:
13.30.1 Ordinary cement finish using ordinary cement sqm 285.00
13.31 Rough cast plaster with a mixture of sand and gravel or crushed
stone from 2.36 to 12.5 mm nominal size dashed over and including
the fresh plaster in two layers, under layer 12 mm cement plaster
1:5(1 cement:5 coarse sand ) and top layer 10 mm cement plaster
1:3(1 cemeht;3 coarse sand) mixed with 10% finely grounded
hydrated lime by volume of cement:
13.31.1 Ordinary cement finish using ordinary cement sqm 277.70
13.32 Pebble dash piaster with a mixture of washed pebble or crushed sqm 271.70
stone 6 mm to 12.5 mm nominal size dashed over and including
fresh plaster in two layers under layer 12 mm cement plaster 1:4(1
cement: 4 coarse sand) and top layer 10 mm cement plaster with
cement mortar 1:3(1 cement :3 coarse sand) mixed with 10% finely
grounded hydrated lime by volume of cement
13.36 Extra for providing and mixing water proofing material in proportion
recommended by the manufacturers:
13.36.1 12 mm cement plaster 1:3(1 cement :3 sand) sqm 7.30
13.36.2 12 mm cement plaster 1:4(1 cement :4 sand) sqm 5.80
13.36.3 15 mm cement plaster 1:3(1 cement :3 sand) sqm 8.40
13.36.4 15 mm cement plaster 1:4(1 cement :4 sand) sqm 6.60
13.36.5 20 mm cement plaster 1:3(1 cement:3 sand) sqm 10.50
13.36.6 20 mm cement plaster 1:4(1 cement: 4 sand) sqm 8.20
13.37 Extra for plastering exterior walls of height more than 10m form
ground level for every additional height of 3 m or part there of sqm 28.80
13.38 Extra for plastering on circular work not exceeding 6 m in radius :
13.38.1 In one coat sqm 12.20
13.38.2 In two coats sqm 17.50
13.39 Extra for plastering done on moulding cornices or architraves
including neat finish to line and level:
13.39.1 In one coat sqm 171.00
13.39.2 In two coats sqm 281.30
13.40 Extra for plastering:
13.40.1 Spherical ceiling sqm 45.30
13.40.2 Groined ceiling sqm 49.70
13.40.3 Flewing soffits sqm 29.50
13.40A Providing and applying plaster of paris putty of 2 mm thickness over
plastered surface to prepare the surface even and smooth complete.
sqm 81.10
13.45 Finishing walls with textured exterior paint of required shade :
13.45.1 New work (Two or more coats applied @ 3.28 ltr/ 10 sqm 122.60
sqm) over and including priming coat of exterior
primer applied @ 2.20 kg/ 10 sqm

BCD/SOR_8th Edition_October 2016 148

Code
Description Unit Rate Rs.
No.
13.46 Finishing walls with Acrylic Smooth exterior paint of required
shade :
13.46.1 New work (Two or more coat applied @ 1.67 ltr/ 10 sqm sqm 71.1
over and including priming coat of exterior primer applied
@ 2.20 kg/ 10 sqm)
13.46A Finishing walls with Premium Acrylic Smooth exterior paint with
Silicone additives of required shade :
13.46A.1 New work (Two or more coat applied @ 1.43 ltr/ 10 sqm sqm 83.6
over and including priming coat of exterior primer applied
@ 2.20 kg/ 10 sqm)
13.48 Finishing with Deluxe Multi surface paint system for interiors and
exteriors using Primer as per manufacturers specifications.
13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over sqm 81.4
and including one coat of special primer applied @ 0.75 ltr
/10 sqm.
13.48.2 Painting wood work with Deluxe Multi Surface Paint of sqm 69.6
required shade. Two or more coat applied @ 0.90 ltr/ 10
sqm over an under coat of primer applied @ 0.75 ltr/ 10
sqm of approved brand and manufacture.
13.48.3 Painting Steel work with Deluxe Multi Surface Paint to give sqm 27.1
an even shade. Two or more coat applied @ 0.90 ltr/ 10
sqm over an under coat of primer applied @ 0.80 ltr/ 10
sqm of approved brand and manufacture.
13.48.4 Extra for lining out plaster to imitate stone or concrete blocks walling sqm 27.1
13.50 12 mm thick plain cement mortar bands in cement mortar 1:4(1
cement: 4 coarse sand):
13.50.1 Flush Band 1 m long 2.10
& 1cm
wide
13.50.2 Sunk Band 1m long & 2.30
1cm wide
13.50.3 Raised Band 1m long & 2.60
1cm wide
13.50.4 Molded Band 1m long & 4.20
1cm wide
13.51 18 mm thick plain cement mortar band in cement mortar 1:4(1
cement :4 coarse sand):
13.51.1 Flush Band 1m long & 2.60
1cm wide
13.51-2 Sunk Band 1m long & 2.90
1cm wide
13.51.3 Raised Band 1m long & 3.20
1cm wide
13.51.4 Molded Band 1m long & 5.70
1cm wide
13.52 18 mm thick molded cement mortar band in two coats, under layer 1m long & 5.60
12 mm thick with cement mortar 1:5(1 cement:5 coarse sand top 1cm wide
layer 6 mm thick with cement mortar 1:4(1 cement :4 coarse sand)

149 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
13.56 Pointing on brick work with cement mortar 1:3(1 cement:3 coarse
sand):
13.56.1 Flush pointing sqm 72.30
13.56.2 Ruled pointing sqm 76.70
13.56.3 Struck or weathered pointing sqm 92.10
13.56.4 Raised and cut pointing sqm 116.10
13.57 Pointing on brick flooring with cement mortar 1:3(1 cement:3 coarse
sand):
13.57.1 Flush pointing sqm 60.30
13.57.2 Ruled pointing sqm 65.00
13.58 Pointing on brick flooring with cement mortar 1:4(1 cement :4 coarse
sand):
13.58.1 Flush pointing sqm 59.30
13.58.2 Ruled pointing sqm 60.20
13.63 Pointing on tile brick work with cement mortar 1:3(1 cement :3 coarse
sand):
13.63.1 Flush pointing sqm 96.10
13.63.2 Ruled pointing sqm 100.10
13.63.3 Struck or weathered pointing sqm 115.90
13.64 Pointing on stone work with cement mortar 1:3(1 cement:3 fine
sand):
13.64.1 Flush pointing sqm 98.70
13.64.2 Ruled pointing sqm 105.70
13.64.3 Raised and cut pointing sqm 179.20
13.68 Pointing on stone slab ceiling with cement mortar 1:2 (1 cement :2
coarse sand):
13.68.1 Flush pointing sqm 56.70
13.68.2 Ruled pointing sqm 60.20
13.69 Extra for pointing on walls on the outside at height more than 10m sqm 5.50
from ground level for every additional height of 3 m or part there of
13.70 White washing with lime to give an ever shade
13.70.1 New work (three or more coats) sqm 12.50
13.70.2 Old work (two or more coats) sqm 6.90
13.70.3 Old work (one or more coats) sqm 3.90
13.71 Satna lime wash on wads one coat sqm 4.60
13.72 White washing with whiting to give an even shade :
13.72.1 New work (three or more goats) sqm 11.20
13.72.2 Old work (two or more coats) sqm 6.70
13.72.3 Old work (one or more coats) sqm 4.00
13.73 Colour washing such as green, blue or buff to give an even shade
13.73.1 New work (two or more coats) with a base coat of white sqm 16.90
washing
13.73.2 New work (two or more coats) with a base coat of whiting sqm 16.60
13.73.3 Old work (two or more coats) with lime sqm 8.80
13.73,4 Old work (two or more coats) with whiting sqm 8.80
13.73.5 Old work ( one or more coats ) with lime sqm 5.00
13.73.6 Old work (one or more coats ) with whitinq sqm 5.00

BCD/SOR_8th Edition_October 2016 150

 Code
Description Unit Rate Rs.
No.
13.74 Removing white or colour wash by scrapping and sand paper in and sqm 4.60
preparing the surface smooth including necessary repair scratches
etc. complete
13.75 Distempering with dry distemper of approved brand and manufacture sqm 46.70
(two or more coats ) and of required shade on new work , over and
including priming coat of whiting to give an even shade.

13.76 Distempering with dry distemper of approved brand and manufacture sqm 21.00
( one or more coats ) and of required shade on old work to give an
even shade .
13.77 Distempering with oil bound washa ble distemper of approved brand
and manufacture to give an even shade .
13.77.2 New work (two or more coats ) over and including priming sqm 69.10
coat with cement primer
13-.77.3 Old work (one or more coats) sqm 22.00
13.77A Distempering with 1st quality washable distemper (ready
made ) of approved manufacturer and of required shade
and colour complete. As per manufacture's specifications.
13.77A.1 Two or more coats on new work sqm 37.20
13.77A.2 One or more coats on old work sqm 22.90
13.78 Applying one coat of cement primer of approved brand and
manufacture on wall surface:
13.78.1 Cement primer sqm 26.90
13.78.2 Distemper primer sqm 28.10
13.79 Finishing walls with water proofing cement paint of approved brand
and manufacture and of required shade to give an even shade
13.79.1 New work (three or more coats) sqm 63.20
13.79.2 Old work (one or more coats) sqm 42.80
13.80 Removing dry or oil bound distemper by scrapping, sand paper and sqm 5.90
preparing the surface smooth including necessary repari scratches
tec. Gmplete
13.80 A.1 Providing and applying white cement based putty of average sqm 77.40
thickness 1 mm, of approved brand and manufacturer, over the
plastered wall surface to prepare the surface even and smooth
complete.
13.80 A.2 Providing and applying white cement based putty of average sqm 118.40
thickness 2 mm, of approved brand and manufacturer, over the
plastered wall surface to prepare the surface even and smooth
complete.
13.81 A Distempering with 1st quality acrylic distemper, having VOC (Volatile
Organic Compound ) content less than 50 grams/ litre, of approved
brand and manufacture,including applying additional coats wherever
required, to achieve even shade and colour.
13.81.1 A One coat sqm 21.70
13.81.2B Two coats sqm 34.20

151 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
13.81 Applying priming coat:

13.81.1 With ready mixed pink or grey primer of approved brand sqm 26.70
and manufacture on wood work (hard and softwood)

13.81.2 with ready mixed aluminum primer of approved brand and sqm 27.60
manufacture on resinous wood and plywood.

13.81.3 With ready mixed zinc chromate yellow primer of approved sqm 22.80
brand and manufacture on steel galvanized iron/steel
works
13.81.4 With ready mixed zinc chromate yellow primer of approved sqm 12.90
brand and manufacture on steel work (second coat)

13.82 Painting with ready mixed paint of approved brand and manufacture
in all shades to give an even shade:
13.82.1 New steel work (two or more coats) sqm 63.60
13.82.2 New wood work (two or more coats) sqm 63.60
13.82.3 Old steel work (one or more coats) sqm 40.70
13.82.4 Old wood work (one more coats) sqm 40.70
13.82.A Painting one thin coat with white lead of approved brand sqm 34.80
and manufacture on wet or patchy portion of plastered
surfaces.
13.82B Finishing with Epoxy paint (two or more coats) at all
locations prepared and applied as per manufacture's
specifications including appropriate priming coat,
preparation of surface, etc. complete.
13.82B.1 On steel work sqm 93.80
13.82B.2 On concrete work sqm 95.50
13.83 Painting on G.S. sheet with synthetic enamel paint of approved brand
and manufacture of required colour to give an even shade:
13.83.1 New work (two or more coats) including a coat of approved sqm 58.00
steel primer but excluding a coat of mordant solution

13.83.A Applying a coat of mordant paint on G.S. sheet.

13.83A.1 1 With a solution of 38 gms of copper acetate in a litre of sqm 14.10
soft water
13.83.A.2 With a solution made of 13 gms hydrochloric acid in a sqm 14.20
solution of 13 gms. Each of copper chloride, copper nitrate
and ammonium chloride dissolved in a litre of soft water
13.84 Painting (two or more coats) onrain water, soil, waster and vent pipes
and fittings with black anticorrosive bitumastic paint of approved
brand and manufacture over and including a priming of ready mixed
zinc chromate yellow primer on new work:
13.84.1 50 mm diameter pipes sqm 12.30
13.84.2 75 mm diameter pipes sqm 17.40
13.84.3 100 mm diameter pipes sqm 23.20
13.84.4 150 mm diameter pipes sqm 34.50

BCD/SOR_8th Edition_October 2016 152

Code
Description Unit Rate Rs.
No.
13.85 Painting (one or more coats) on rain water, soil waste and vent pipes
and fittings with black anticorrosive bitumastic paint approved brand
and manufacture on old work:
13.85.1 50 mm diameter pipes sqm 5.60
13.85.2 75mm diameter pipes sqm 7.90
13.85.3 100 mm diameter pipes metre 10.40
13.85.4 150 mm diameter pipes metre 15.10
13.86 Painting (two or more coats) on rain water, soil, waste and vent pipes
and fittings with synthetic enamel paint of approved brand and
manufacture and required colour over a priming coat of ready mixed
zinc chromatic yellow primer on new work.
13.86.1 50 mm diameter pipes metre 13.10
13.86.2 75 mm diameter pipes metre 18.20
13.86.3 100 mm diameter pipes metre 24.20
13.86.4 150 mm diameter pipes metre 36.00
13.87 Painting (one more coats) on rain water soil, waste and vent pipes
and filings with synthetic enamel paint of approved brand and
manufacture and required colour on old work:
13.87.1 50 mm diameter pipes metre 5.80
13.87.2 75 mm diameter pipes metre 8.40
13.87.3 100 mm diameter pipes metre 10.90
13.87.4 150 mm diameter pipes metre 15.70
13.88 Painting with oil type wood preservative of approved brand and
manufacture:
13.88.1 New work (two or more coats) sqm 20.20
13.88.2 Old work(one or more coats) sqm 14.80
13.88 A Providing and applying two coats of fire retardent paint FR 881 sqm 212.70
unthinned on cleaned wood/ply surface @ 3.5 sqm per litre per coat
inncluding preparation of base surface as per recommendationnns of
fmanufacturer to make the surface fire retardent.
13.89 Coal tarring two coats on new work using 0.16 and 0.12 litre coat sqm 24.50
sqm in the first coat and second coat respectively.
13.92 Wall painting with plastic emulsion paint of approved brand and
manufacture to give an even shade:
13.92.1 Two or more coats on new work sqm 59.90
13.92.2 One or more coats on old work sqm 38.50
13.93 Painting with synthetic enamel paint of approved brand and
manufacture to give an even shade:
13.93.1 Two or more coats on new work sqm 54.10
13.93.2 One or more coats on old work. sqm 34.80
13.94 Painting with synthetic enamel paint of approved brand and
manufacture of required colour to give an even shade:
13.94.1 Two or more coats on new work over an under coat of sqm 75.20
suitable shade with ordinary pain+ of approved brand and
manufacture
13.95 Painting with aluminum paint of approved brand and manufacture
to give an even shade.
13.95.1 Two or more coats on new work sqm 45.90
13.95.2 One or more coats on old work. sqm 29.40

153 BCD/SOR_8th Edition_October 2016

 13.96 Painting with acid proof paint of approved brand and manufacture
of required colour to give an even shade:
13.96.1 Two or more coats on new work. sqm 54.20
13.96.2 One or more coats on old work. sqm 35.00
13.97 Painting with black anti-corrosive bitumastic paint of approved brand
and manufacture to give an even shade:
13.97.1 Two or more coats on new work sqm 42.80
13.97.2 One or more coats on old work. sqm 28.20
13.98 Floor painting with floor enamel paint of approved brand and
manufacture of required colour to give an even shade:
13.98.1 Two or more coats on new work. sqm 54.60
13.98.2 One or more coats on ole work. sqm 35.30
13.1 Varnishing with varnish of approved brand and manufacture:
13.100.1 Two or more coats of glue sizing with copal varnish over an sqm 78.40
under coat of flatting varnish.
13.100.3 One or more coats with copal varnish. sqm 32.40
13.100.4 Two more coats glue sizing with spar varnish or an under sqm 79.60
coat of flatting varnish.
13.100.6 One or more coats with sprit varnish. sqm 33.10
13.101 French spirit polishing:
13.101.1 Two or more coats on works including a coat of wood filler. sqm 138.60

13.101.2 One or more coats on old work. sqm 71.00

13.104 Polishing on wood work with ready made wax polish of approved
brand and manufacture:
13.104.1 New work sqm 59.40
13.104.2 Old work sqm 30.00
13.105 Floor polishing on masonry or concrete floors with wax polish off sqm 26.60
approved brand and manufacture.
13.106 Lettering with black Japan paint of approved brand and manufacture 1 letter of 1.70
1cm hight
13.107 Re-lettering with black Japan paint of approved brand and 1 fetter of 1.10
manufacture. 1cm hight
13.112 Washed stone grit plaster in two layers, under layer 12 mm cement
plaster 1:4 (1 cement :4 coarse sand) furrowing the under layer with
scratching tool, applying cement slurry on the under layer @ 2 kg of
cement per square metre, tope layer 15 mm cement plaster 1:1/2:2
(1 cement: 1/2 coarse sand :2 stone chipping 10 mm nominal size) in
panels with groove all around as per approved pattern including
scrubbing and washing, the top layer with brushes and water to
expose the stone chippings, complete as per specification and
direction of Engineer -in charges (Payment for providing grooves
shall be made separately) sqm 377.60

BCD/SOR_8th Edition_October 2016 154

Code
Description Unit Rate Rs.
No.
13.113 Forming groove of uniform size in the top layer of washed stone grit
piaster as per approved pattern using wooden batten nailed to the
under layer including removal of wooden battens, repair to the edges
of panels and finishing the groove complete as per specifications and
direction of the Engineer-in-charges.
13.113.1 15 mm wide and 15 mm deep groove metre 19.50
13.113.2 20 mm wide and 15 mm deep groove metre 20.00
13.114 Extra for washed grit plaster on exterior walls of height more than 10 sqm 40.50
m from ground level for every additional hight of 3 m or part there of
13.115 Extra for washed stone grit plaster on circular work not exceeding 6m sqm 32.70
in radius (in coats).
13.116 Forming groove of uniform size from 12x12 mm and upto 25x15 mm metre 33.80
in plastered surface as per approved pattern using wooden battens,
nailed to the under layer including removal of wooden battens,
repairs to the edges of plaster panel and finishing the groove
complete as per specifications and direction of the Engineer-in-
Charge.
13.117 Extra for using white cement in place of ordinary cement in the top sqm 99.00
layer of the item washed stone grit plaster.

155 BCD/SOR_8th Edition_October 2016

 SUB HEAD : 14.0
REPAIRS TO BUILDINGS
 BUILDING WORK - Contd.

14.0 Repairs to Buildings

Code
Description Unit Rate Rs.
No.
14.1 Repairs to plaster of thickness 12 mm to 20 mm in patches of
area 2.5 sqm and under including cutting the patch in proper
shape and preparing and plastering the surface of the walls
complete including disposal of rubbish to the dumping ground
within 50 metres lead.
14.1.2 With cement mortar 1:4(1 cement:4 coarse sand) sqm 171.00
14.2 Fixing chowkhats in existing opening including embedding
chowkhats in floors or walls cutting masonry for holdfasts
embedding holdfasts in cement concrete blocks with cement
concrete 1:3:6)1 cement :3 coarse sand:6 grade stone aggregate
20 mm nominal size) painting two coats of coal tar to sides of
chowkhats and making good the damages to walls and floors as
required complete including disposal of rubbish to the dumping
ground within 50 metres lead.
14.2.1 Door chowkhats each 531.90
choukhat
14.2.2 Window chokhats each 315.50
choukhat
14.2.3 Clerestory window chowkhats each 233.10
choukhat
14.3 Making opening in brick masonry including dismantling, fixing
chowk hats in floor or walls cutting masonry and fixing hold fasts
in cement concrete 1:3:6(1 cement:3 coarse sand:6 stone
aggregate 20 mm nominal size) painting two coats of coal tar io
sides of choukhat and making good the damages to walls and
floors complete to match the existing surface.
14.3.1 For door each 678.50
choukhat
14.3.2 For window each 452.10
choukhat
14.3.3 For clerestory window each 284.80
choukhat
14.4 Providing and fixing wooden cleats of size 100 mm x75 mm x50
mm to doors and windows with approved fittings including
removal of old cleats where necessary including painting,
polishing or bees waxing to match the existing shade:
14.4.1 2nd class teak wood cleats with brass hinges and each 65.70
screws
14.4.3 Sal wood cleats with brass with brass hinges and each 59.20
screws
14.4.5 Kind class teak wood cleats with iron hidings and each 47.80
screws
14.4.7 Sal wood cleats with iron hinges and screws each 41.30
14.4.8 1st class kail wood cleats with iron hinges and screws each 29.20
14.4.9 2nd class kail wood cleats with iron hinges and screws each 29.20

156 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
14.5 Renewing glass panes, with putty and nails wherever
necessary:
Float glass panes weighing 10 kg/m2 (4mm thick 618.10
14.5.2 sqm
glass)
Float glass panes weighing 13.75 kg/m2 (5.5mm 846.40
14.5.3 sqm
thick glass)
14.6 Renewing glass, with wooden fillets wherever necessary:
14.6.2 Float glass panes weighing 10kg/m2 (4mm thick) sqm 715.30
Float glass panes weighing 13.75kg/m2 (5.5mm 969.60
14.6.3 sqm
thick)
14.7 Renewing galss panes and re fixing existing wooden fillets:
14.7.2 Float glass panes weighing 10 kg/m2 (4mm thick) sqm 613.00
Float glass panes weighing 13.75kg/m2 (5.5 mm 841.30
14.7.3 sqm
thick)
14.8 Supplying and fixing new wooden fillets wherever necessary
14.8.1 Second class teak wood fillets sqm 25.00
14.8.3 Hollock wood fillets sqm 20.30
14.9 Renewal of old putty of glass panes (length) metre 14.50
14.1 Refixing old glass panes with putty and nails sqm 18.80
14.11 Fixing old glass panes with wooden fillets (excluding cost of 158.70
sqm
fillets)
14.12 Providing and fixing 16 mm M.S. Fan clamps of standard shape 180.20
and size in existing R.C.C slab including cutting chase and
each
making good ad painting exposed portion of the clamps
complete
14.14 Replacing sand stone slabs in roofing laid in cement mortar 1:4
(1 cement:4 coarse sand) including necessary repairs and
cement pointing with same mortar complete including disposal
of rubbish to dumping ground within 50 metres lead:
- RED SAND STONE
14.14.1 30 to 40 mm thick sqm 370.30
14.14.2 45 mm thick sqm 405.60
14.14.3 50 mm thick sqm 424.90
- WHITE SAND STONE
14.14.4 30 TO 40mm thick sqm 397.20
14.14.5 45 mm thick sqm 476.70
14.14.6 50 mm thick sqm 408.80
14.18 Renewing wooden battens in roos, including making good the
holes in wall and painting with C type wood preservative of
approved brand and manufacture complete including removal
of rubbish to the dumping ground within 50 meters lead:
14.18.1 Sal wood battens cum 67502.00

BCD/SOR_8th Edition_October 2016 157

Code
Description Unit Rate Rs.
No.
14.19 Renewing wooden beams in roofs including making good the
holes in wails and painting with oil type wood preservative of
approved brand and manufacture complete including removal
of rubbish to the dumping ground within 50 metres lead.
14.19.1 Not exceeding 4.00 metres in length
14:19.1.1 Sal wood beams cum 72741.10
14.19.1.4 Hollock wood beams cum 48213.40
14.19.2 Above 4.00 metres and upto 5.00 metres length
14.19.2.1 Sal wood beams cum 74076.00
14.19.2.4 Hollock wood beams cum 73838.00
14.21 Raking out joints in lime or cement mortar and preparing the sqm 16.90
surface for repainting or re plastering including disposal of
rubbish to the dumping within 50 metres lead
14.29 Taking out wind ties from roof including cutting out rusted bolts, Kg 0.50
nuts etc, and removing materials to any distance within
compound and stacking.
14.3 Fixing of old wind tie with new fittings including painting two or metre 63.20
more coats with anticorrosive bitumastic paint of approved
brand & manufacturer over and including priming coat of ready
mixed zinc chromate yellow primer of approved brand.
14.31 Renewing bottom rail and /or top runner of collapsible gate kg 67.00
including making good all damages and applying priming coat
of zinc chromate yellow primer of approved brand and
manufacturer

158 BCD/SOR_8th Edition_October 2016

 SUB HEAD : 15.0
DISMANTLING AND
DEMOLISHING
 BUILDING WORK - Contd.

15.0 Dismantling and Demolishing

Code
Description Unit Rate Rs.
No.
15.1 Demolishing lime concrete and disposal of material within 50 cum 203.10
metre lead.
15.2 Demolishing cement concrete including disposal of material
within 50 metre lead:
15.2.1 1:3:6 or richer mix cum 578.30
15.2.2 1:4:8 or leaner mix cum 357.30
15.3 Demolishing R.C.C. work including stacking of steel bars and cum 839.00
disposal of unserviceable material withing 50 metres lead:
15.4 Demolishing R.B. work including stacking of steel bars and cum 752.20
disposal of unserviceable material within 50 metres lead:
15.5 Extra for cutting reinforcement bars in R.C.C. or R.B. work Per RCC 294.50
(Payment shall be made on the cross sectional area of R.C.C.
or R.B. work)
15.6 Extra for scrapping, cleaning and straightening reinforcement kg 2.30
from R.C.C. or R.B. work.
15.7 Demolishing brick work including stacking of serviceable
material and disposal of unserviceable material within 50
meters lead:
15.7.1 In mud mortal cum 169.30
15.7.2 In lime mortar with old mugnal bricks cum 419.40
15.7.3 In lime mortar cum 203.10
15.7.4 In cement mortar cum 491.30
15.8 Removing mortar form bricks and cleaning bricks including
stacking within a lead of 50m (stacks of cleaned bricks shall be
measured):
15.3.1 From brick work in mud mortar cum 1109.80
15.8.3 From brick work in lime mortar cum 1286.90
15.3.1 From brick work in cement mortar cum 1608.30
15.9 Demolishing stone rubble masonry including stacking of
serviceable material and disposal of unserviceable material
within 50 meters lead.
15.9.1 In lime mortar cum 276.80
15.9.2 In cement mortar cum 585.80
15.10 Desman tiling dressed stone work ashlar face stone work,
marble work or precast concrete work including stacking of
service able and disposal of unserviceable material within 50
metres lead:
15.10.1 In lime mortar cum 350.10
15.10,2 In cement mortar cum 684.50
15.11 Removing mortar form stones and cleaning stones and
concrete articles (net quantity of stacks of cleaned materials will
be measured)
15.11.1 In lime mortar cum 115.16
15.11.2 In cement mortar cum 164.30

159 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
15.12 Desman tiling doors windows and clerestory windows (steel or
wood) shutters including chowkhats, architrage, holdfasts etc.
complete and stacking within 50 metres lead:
15.12.1 Of area 3 sqm and below each 90.30
15.12.2 Of area beyond 3 sqm each 124.50
15.13 Taking out doors, windows and clerestory window shutters
(steel or wood) including stacking within 50 meters lead.
15.13.1 Of area 3 sqm and below each 35.00
15.13.2 Of area beyond 3 sqm each 46.50
15.14 Dismantling wood work in frames, trusses, purlins and rafters
upto 10 metres span and 5 metres height including stacking the
material within 50 metres lead:
15.14.1 Of sectional area 40 cm* and above cum 1095.20
15.14.2 2 m 4.40
Of sectional area below 40cm
15.15 Extra for dismantling trusses, rafters, purlins etc. of wood work
for every additional span of of one metre or part thereof beyond
10 me res:
15.1!).1 Of sectional area 40 cm2 and above metre span 158.60
15.15.2 Of sectional area below 40 cm2 meter span 0.50
15.16 Extra for dismantling trusses, rafters purlins etc. of wood work
for every additional height of one meter or part thereof beyond 5
meters.
15.16.1 Of sectional area 40 square centimeters and above cum 221.50
15.16.2 Of sectional area below 40 square centimeters m 0.90
15.17 Dismantling steel work in single sections including
dismembering and stacking within 50 meters lead in:
15.17.1 R.S. Joists kg 0.80
15.17.2 Channels.angles, tees and flats kg 0.60
15.18 Dismantling steel work in built up sections in angles, tees, flats kg 1.40
and channels including all gusset plats, bolts, nuts, cutting
hvets, welding etc. including dismem bering and stacking within
50 metres lead.
15.19 Dismantling steel work in built up sections without kg 1.00
dismembering and stacking within 50 metres lead
15.2 Extra for dismantling trusses, rafters, purlins etc. Of steel work kg 0.20
for every additional span of one metre or part thereof beyond 10
metres
15.21 Extra for dismantling trusses, rafters, purlins etc. Of steel work kg 0.20
for every additional height of one metre or part there of beyond
5 metres
15.22 Extra for marking of structural steel work required to be re- kg 1.00
erected.

BCD/SOR_8th Edition_October 2016 160

Code
Description Unit Rate Rs.
No.
15.23 Dismantling tile work in floors and roofs laid in cement mortar
including stacking material within 50 metres lead.
15.23,1 For thickness of tiles 10 mm to 25 mm sqm 18.40
15.23.2 For thickness of tiles above 25 mm and upto 40 mm sqm 28.30
15.24 Demolishing dry brick pitching in floors, drains etc. including cum 321.80
stacking serviceable material and disposal of unserviceable
material within 50 metres lead.
15.25 Dismantling stone slab flooring laid in cement mortar including sqm 63.60
stacking of serviceable material and disposal of unserviceable
material within 50 metres lead.
15.26 Demolishing brick tile covering in terracing including stacking of sqm 26.30
serviceable material and disposal of unserviceable material
within 50 metres lead.
15.27 Demolishing mud phaska in terracing and disposal of material cum 221.10
within 50 metres lead
15.28 Dismantling roofing including ridges, hips valleys and gutters
etc. and stacking the material within 50 metres lead of:
15.28.1 G.S. Sheet sqm 40.20
15.28.2 Asbestos sheet sqm 19.00
15.29 Dismantling stone slab roofing over wooden karries or R.C.C cum 636.20
battens (dismantling karries and battens to be paid for
separately) including stacking of serviceable material and
disposal of unserviceable material within 50 metres lead:
15.3 Dismantling jack arch roofing and floors including stacking of sqm 61.40
serviceable material and disposal of unserviceable material
within 50 metres lead.
15.31 Dismantling tiled roofing with battens boarding etc. complete sqm 49.90
including stacking of serviceable material and disposal of
unserviceable material within 50 metres lead.
15.32 Demolishing thatch roofing including mats,bamboo,jaffari etc, sqm 13.80
complete including stacking of serviceable material and disposal
of unserviceable material within 50 metres lead .
15.33 Dismantling wooden bailies in posts and struts including m 5.00
stacking within 50 metres lead
15.34 Dismantling and stacking 50 metres lead.tencing posts or struts
including all earth work and dismantling of concrete etc. in base
of:
15.34.1 T' or 'I.' iron or pipe each 74.10
15,34.2 R. C. C. each 89.25
15.35 Cutting bailies or wooden posts of fencing at the point of each 8.60
projection above the concrete or ground and stacking the same
within 50 metres lead.
15.36 Dis nantling barbed wire or flexible rope in fencing including kg 8.60
making roll:; and stacking within 50 metres lead.

161 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
15.37 Dismantling wooden trellis work excluding frames but including sqm 15.90
stacking the serviceable material within 50 metres lead.

15.38 Dismantling expanded metal or R.R.C. fabrics with necessary sqm 18.60
battens and beading including stacking the serviceable material
within 50 metres lead.
15.39 Dismantling wooden boardings in lining of walls and partitions,
excluding supporting members but including stacking within 50
metres lead.
15.39.1 Upto 10 mm thick sqm 15.40
15.39.2 Thickness above 10 mm upto 25 mm sqm 19.70
15.39.3 Thickness above 25 mm upto 40 mm sqm 23.50
15.4 Dismantling precast concrete or stone slabs in walls , partition
walls etc. including stacking within 50 metres lead.
15.40.1 Thickness upto 40 mm sqm 69.70
15.40.2 Thickness above 40 mm upto 75 mm sqm 104.30
15.41 Dismantling cement asbestos, Celotax or other hard board sqm 14.20
ceiling or partition walls including stacking of serviceable
materials and disposal of unserviceable materials within 50
metres lead.
15.42 Dismantling C.I. or asbestos rain water pipe with fittings and
clamps including stacking the material within 50 metres lead.
15.42.1 75 to 80 mm dia pipe . m 18.10
15.42.2 100 mm dia pipe m 18.70
15.42.3 150 mm dia pipe m 19.40
15.43 Dismantling including stacking of serviceable material and
disposal of unserviceable material within 50 metres lead.
15.43.1 Water bound macadam road sqm 54.40
15.43.2 '. Bituminous road sqm 104.70
15.45 Dismantling G.I. pipes including excavation and refilling
trenches after taking out the pipes , breaking lead caulked
joints, melting of lead and making into blocks including stacking
of pipes , lead at site within 50 metres lead.
15.45.1 Upto 150 mm diameter m 102.20
15.45.2 Above 150 mm dia upto 300 mm dia m 140.70
15.45.3 Above 300 mm diameter m 184.80
15.46 Dismantling steel cylinder R.C. pipes including excavation and
refilling trenches after laking out the pipes. Breaking lead
caulked joints, melting of lead and making into blocks including
stacking or pipes , lead at site within 50 metres lead.

15,46,1 Upto 600 mm diameter m 183.40

15.46.2 Above 600 mm diameter m 454.00

BCD/SOR_8th Edition_October 2016 162

Code
Description Unit Rate Rs.
No.
15.47 Dismantling asbestos cement pressure pipes including
excavation and refilling trenches after laking out the pipes and
stacking the pipes within 50 metres lead .
15.47.1 Upto 150 mm diameter m 76.90
15.47.2 Above 150 mm diameter m 93.50
15.48 Taking out C. I. cover with frame from R.C.C. top slab of each 172.10
manholes of various sizes including demolishing of R.C.C, wor k
and stacking of useful materials near the site and disposal of
unserviceable materials into municipal dumps within 50 metres
lead.
15,49 Taking out C.I. cover with frame from R.C.C. top slab of each 101.80
inspection chambers of various sizes including demolishing of
R.CC. work and stacking of useful materials near the site and
disposal of unserviceable materials into municipal dumps within
50 metres
15.50 Dismantling of R.C.C. spun vent shaft including excavating the each 1127.40
cement concrete pit completely , taking out the shaft, refilling
the excavated gap, stacking the useful materials near the site
and disposal of unserviceable materials within 50 metres lead.
15.51 Dismantling or road gully chamber or various sizes including each 232.30
C.I. grating with frame including stacking of useful materials
near the site and disposal of unserviceable materials into
municipal dumps within 50 metres lead including refilling the
excavated
15.52 Dismantling of flushing cistern of any size including stacking of each 240.90
useful materials near the site and disposal of unserviceable
materials within 50 metres lead.
15.53 Dismantling of C.I. sluice valve including stacking of useful
materials within a lead of 50 metres.
15.53. Upto 150 mm dia . nos 88.80
15.53.L Above 150 mm diameter nos 297.80
15.54 Dismantling of spindle fire hydrant including stacking of useful nos 175.70
materials within 50 metres lead
15.55 Dismantling of cement concrete platform along with curtain wall
and base concrete etc. including stacking of useful materials
near the site and disposal of unserviceable materials within 50
metres lead.
15.55.1 120x120 cm(outside to outside) nos 256.70
15.55.2 210x120 cm (outside to outside) nos 393.90
15.55.3 320x120 cm (outside to outside) nos 557.20
15.56 Dismantling old plaster or skirting raking out joints and cleaning sqm 12.80
the surface for plaster including disposal of rubbish to the
dumping ground within 50 metres lead.

163 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
15.57 Dismantling alumiuium/Gypsum partitions, doors, windows, sqm 14.20
fixed glazing and false ceiling including disposal of
unserviceable surplus material and stacking of serviceable
material with in 50 m lead as directed by Engineer-in-charge.
BARRICADING WORK
15.58 Providing sal ballah barricading with departmental sal ballah Per m 150.20
average 150 dia. And 2M long sal ballah post at interval of 2.5
M C/C fixed 0.5 M average below ground, packed with earth
and Brick bats, well watered and rammed with three rows of
average 100mm dia. Sal ballah horizontal runners fixed with
iron spikes and wires, white washing one coat to exposed
surface, dismantling the barricade after function, filling the
holes, excluding carriage of sal ballah from and to godown up to
5K.M. lead, stacking them in countable stacks in godown
including cost of all labour and materials and taxes all complete
job as per specification and direction of E/l.
15.58A Demolishing R.C.C. work by mechanical means and stockpiling Per cum 1084.10
at designated locations and disposal of dismantled materials up
to a lead of 1 kilometre, stacking serviceable and unserviceable
material separately including cutting reinforcement bars.

15.59 Dismantling of flexible pavement (bituminous courses) by Per cum 162.70

mechanical means and disposal of dismantled material up to a
lead of 1 kilometre, as per direction of Engineer-in-charge.
15.60 Disposal of building rubbish / malba / similar unserviceable, Per cum 124.90
dismantled or waste materials by mechanical means, including
loading, transporting, unloading to approved municipal dumping
ground or as approved by Engineer-in-charge, beyond 50 m
initial lead, for all leads including all lifts involved.

BCD/SOR_8th Edition_October 2016 164

 SUB HEAD : 17.0
SANITARY INSTALLATIONS
 BUILDING WORK - Contd.

17.0 Sanitary Installations

Code Description
Unit Rate Rs.
No.
17.1 Providing and fixing water closet squatting pan (Indian type W.C.pan )
with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete,
including cutting and making good the walls andlevel white P.V.C.
flushing cistern, including flush pipe, with manually controlled device
(handle lever) conforming to IS : 7231, with all fittings and floors
wherever required :
17.1.1 White Vitreous china Orissa pattern W.C. pan of size each 3049.30
580x440 mm with integral type foot rests
17.1.2 Stainless Steel AISI-304(18/8) Orissa pattern W.C. pan of each 6735.90
size 585x480 mm with flush pipe and integrated type foot
rests
17.2 Providing and fixing white vitreous china pedestal type water closet
(European type W.C. pan) with seat and lid, 10 litre low level white
P.V.C. flushing cistern, including flush pipe, with manually controlled
device (handle lever), conforming to IS : 7231, with all fittings and
fixtures complete, including cutting and making good the walls and
floors wherever required :
17.2.1 W.C. pan with ISI marked white solid plastic seat and lid each 2970.00
17.2.2 W.C. pan with ISI marked black solid plastic seat and lid each 2903.00
17.3 Providing and fixing white vitreous china pedestal type water closet
(European type) with seat and lid, 10 litre low level white vitreous china
flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm
flush bend, overflow arrangement with specials of standard make and
mosquito proof coupling of approved municipal design complete,
including painting of fittings and brackets, cutting and making good the
walls and floors wherever required :
17.3.1 W.C. pan with ISI marked white solid plastic seat and lid each 4416.00
17.3.2 W.C. pan with ISI marked black solid plastic seat and lid each 4391.50
17.4 Providing and fixing white vitreous china flat back or wall corner type
lipped front urinal basin of 430x260x350 mm and 340x410x265 mm
sizes respectively with automatic flushing cistern with standard flush
pipe and C.P. brass spreaders with brass unions and G.I clamps
complete, including painting of fittings and brackets, cutting and
making good the walls and floors wherever required :
17.4.1 One urinal basin with 5 litre white P.V.C. automatic flushing each 2859.90
cistern
17.4.2 Range of two urinal basins with 5 litre white P.V.C. automatic each 4685.90
flushing cistern
17.4.3 Range of three urinal basins with 10litre white P.V.C. each 6205.20
automatic flushing cistern
17.4.4 Range of four urinal basins with 10 litre white P.V.C. each 8579.90
automatic flushing cistern

165 BCD/SOR_8th Edition_October 2016

 Code Description
Unit Rate Rs.
No.
17.5 Providing and fixing white vitreous china flat back half stall urinal of
size 580x380x350 mm with white PVC automatic flushing cistern,with
fittings, standard size C.P. brass lush pipe, spreaders with unions and
clamps (all in C.P. brass) with waste fitting as per IS :2556, C.I. trap
with outlet grating and other couplings in C.P. brass, including painting
of fittings and cutting and making good the walls
and floors wherever required :
17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing each 5460.00
cistern
17.5.2 Range of two half stall urinals with 5 litre P.V.C. automatic each 8689.20
flushing cistern
17.5.3 Range of three half stall urinals with 10 litre P.V.C. automatic each 11542.20
flushing cistern
17.5.4 Range of four half stall urinals with 10 litre P.V.C. automatic each 14257.60
flushing cistern
17.6 Providing and fixing one piece construction white vitreous china
squatting plate with an integral longitudinal flushing pipe, white
P.V.C.automatic flushing cistern, with fittings, standard size G.I. /
PVCflush pipe for back and front flush with standard spreader pipes
with fittings, G.I clamps and C.P. brass coupling complete, including
painting of fittings and cutting and making good the walls and floors
etc. wherever required :
17.6.1 Single squatting plate with 5 litre P.V.C. automatic flushing each 3432.50
cistern
17.6.2 Range of two squatting plates with 5 litre P.V.C. automatic each 5067.10
flushing cistern
17.6.3 Range of three squatting plates with 10 litre P.V.C. each 6733.10
automatic flushing cistern
17.6.4 Range of four squatting plates with 10 litre P.V.C. automatic each 8233.50
flushing cistern
17.7 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass
pillar taps, 32 mm C.P. brass waste of standard pattern, including
painting of fittings and brackets, cutting and making good the walls
wherever require :
17.7.1 White Vitreous China Wash basin size 630x450 mm with a each 2093.50
pair of 15 mm C.P. brass pillar taps
17.7.2 White Vitreous China Wash basin size 630x450 mm with a each 1818.50
single 15 mm C.P. brass pillar tap
17.7.3 White Vitreous China Wash basin size 550x400 mm with a each 1879.80
pair of 15 mm C.P. brass pillar taps
17.7.4 White Vitreous China Flat back wash basin size 550x 400 each 1604.90
mm with single 15 mm C.P. brass pillar tap
17.7.5 White Vitreous China Angle back wash basin size 600x480 each 1818.50
mm with single 15 mm C.P. brass pillar tap
17.7.6 White Vitreous China Angle back wash basin size 400x400 each 1452.30
mm with single 15 mm C.P. brass pillar tap
17.7.7 White Vitreous China Flat back wash basin size 450x300 each 1452.30
mm with single 15 mm C.P. brass pillar tap

BCD/SOR_8th Edition_October 2016 166

Code Description
Unit Rate Rs.
No.
17.7.8 White Vitreous China Surgeon type wash basin of size each 3747.50
660x460 mm with a pair of 15 mm C.P. brass pillar taps with
elbow operated levers
17.7.9 White Vitreous China Surgeon type wash basin of each 2874.40
size660x460 mm with single 15 mm C.P. brass pillar taps
with elbow operated levers ISI marked
17.7.10 Stainless Steel AISI-304(18/8) Round basin 405x355 mm each 3191.80
with single 15 mm C.P. brass pillar tap
17.7.11 Stainless Steel AISI-304(18/8) Wash basin 530x345 mm with each 2947.70
single 15 mm C.P. brass pillar tap
17.8 Providing and fixing white vitreous china pedestal for wash basin each 1021.20
completely recessed at the back for the reception of pipes and fittings.
17.9 Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain
with rubber plug, 40 mm C.P. brass waste complete, including painting
the fittings and brackets, cutting and making good the walls wherever
required :
17.9.1 White glazed fire clay kitchen sink of size 600x450x250 mm each 2351.50
17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per
IS : 13983 with C.I. brackets and stainless steel plug 40 mm,including
painting of fittings and brackets, cutting and making good the walls
wherever required :
17.10.1 Kitchen sink with drain board
17.10.1.1 510x1040 mm bowl depth 250 mm each 7099.60
17.10.1.2 510x1040 mm bowl depth 225 mm each 6812.80
17.10.1.3 510x1040 mm bowl depth 200 mm each 5958.30
17.10.1.4 510x1040 mm bowl depth 178 mm each 4432.40
17.10.2 Kitchen sink without drain board
17.10.2.1 610x510 mm bowl depth 200 mm each 4394.00
17.10.2.2 610x460 mm bowl depth 200 mm each 3978.60
17.10.2.3 470x420 mm bowl depth 178 mm each 3093.60
17.11 Providing and fixing white vitreous china laboratory sink with C.I.
brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste
and 40mm C.P. brass trap with necessary C.P. brass unions complete,
including painting of fittings and brackets, cutting and making good the
wall wherever required :
17.11.1 Size 450x300x150 mm each 2125.60
17.11.2 Size 600x450x200 mm each 2986.20
17.12 Providing and fixing draining board with C.I. brackets including painting
of brackets, cutting and making good the walls wherever required :
17.12.1 White glazed fire clay draining board of size 600x450x25 mm each 1164.10
17.13 Providing and fixing white vitreous china water closet squatting pan
(Indian type) :
17.13.1 Long pattern W.C. pan of size 580 mm each 889.40
17.13.2 Orissa pattern W.C. pan of size 580x440 mm each 1292.20
17.14 Extra for using coloured W.C. pan instead of white W.C. pan :
17.14.1 Orissa pattern W.C. pan 580x440 mm each 659.20

167 BCD/SOR_8th Edition_October 2016

 Code Description
Unit Rate Rs.
No.
17.15 Providing and fixing white vitreous china pedestal type (European type/ each 1194.50
wash down type) water closet pan.
17.16 Extra for using coloured pedestal type W.C pan (European type)with low each 1519.80
level cistern of same colour instead of white vitreous china W.C pan and
cistern.
17.17 Providing and fixing a pair of white vitreous china foot rests of standard
pattern for squatting pan water closet :
17.17.1 250x130x30 mm pair 158.40
17.17.2 250x125x25 mm pair 158.40
17.18 Providing and fixing P.V.C. low level flushing cistern with manually
controlled device (handle lever) conforming to IS : 7231, with all fittings
and fixtures complete.
17.18.1 10 litre capacity - White each 859.40
17.18.2 10 litre capacity - coloured each 918.10
17.19 Providing and fixing controlled flush, low level cistern made of vitreous
china with all fittings complete.
17.19.1 10 litre (full flush) capacity-white each 1487.90
17.19.2 10 litre (full flush) capacity-coloured each 2128.80
17.20 Providing and fixing solid plastic seat with lid for pedestal type W.C. pan
complete :
17.20.1 White solid plastic seat with lid each 430.50
17.20.2 Black solid plastic seat with lid each 406.10
17.20.3 Coloured (other than black & white) solid plastic seat with lid each 699.00

17.21 Deleted.
17.22 Providing and fixing G.I. inlet connection for flush pipe connecting with each 107.00
W.C. pan.
17.23 Providing and fixing white vitreous china flat back or wall corner type each 786.20
lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes
respectively.
17.24 Providing and fixing white vitreous china squatting plate urinal with each 1532.00
integral rim longitudinal flush pipe.
17.25 Providing and fixing white vitreous china wash basin including making all
connections but excluding the cost of fittings :
17.25.1 Flat back wash basin of size 630x450 mm each 1015.70
17.25.2 Flat back wash basin of size 550x400 mm each 802.10
17.25.3 Angle back wash basin of size 600x480 mm each 1015.70
17.25.4 Angle back wash basin of size 400x400 mm each 649.50
17.25.5 Flat back wash basin of size 450x300 mm each 649.50
17.25.6 Surgeon type wash basin of size 660x460 mm each 1473.50
17.26 Providing and fixing kitchen sink including making all connections
excluding cost of fittings.
17.26.1 White glazed fire clay sink of size 600x450x250 mm each 1753.70
17.27 Providing and fixing white vitreous china laboratory sink including
making all connections excluding cost of fittings :
17.27.1 Size 450x300x150 mm each 1106.70
17.27.2 Size 600x450x200 mm each 1967.30

BCD/SOR_8th Edition_October 2016 168

Code
Description Unit Rate Rs.
No.
17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including
P.V.C. waste fittings complete.
17.28.1 Semi rigid pipe
17.28.1.1 32 mm dia each 78.50
17.28.1.2 40 mm dia each 84.60
17.28.2 Flexible pipe
17.28.2.1 32 mm dia each 76.10
17.28.2.2 40 mm dia each 78.50
17.29 Providing and fixing 100 mm sand cast Iron grating for gully trap. each 30.60
17.30 Providing and fixing in position 25 mm diameter mosquito proof coupling each 40.40
of approved municipal design.
17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass each 690.70
(of approved quality) complete with 6 mm thick hard board ground fixed
to wooden cleats with C.P. brass screws and washers complete.

17.32 Providing and fixing mirror of superior glass (of approved quality) and of
required shape and size with plastic moulded frame of approved make
and shade with 6 mm thick hard board backing :

17.32.1 Circular shape 450 mm dia each 801.30

17.32.2 Rectangular shape 453x357 mm each 636.90
17.32.3 Oval shape 450x350 mm (outer dimensions) each 695.80
17.32.4 Rectangular shape 1500x450 mm each 1272.20
17.33 Providing and fixing 600x120x5 mm glass shelf with edges round each 473.70
off,supported on anodised aluminium angle frame with C.P. brass
brackets and guard rail complete fixed with 40 mm long screws, rawl
plugs etc., complete.
17.34 Providing and fixing toilet paper holder :
17.34.1 C.P. brass each 315.20
17.34.2 Vitreous china each 296.70
17.35 Providing and fixing soil, waste and vent pipes :
17.35.1 100 mm dia
17.35.1.1 Sand cast iron S&S pipe as per IS: 1729 metre 887.30
17.35.1.2 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as metre 989.60
per IS: 3989
17.35.2 75 mm diameter :
17.35.2.1 Sand cast iron S&S pipe as per IS: 1729 metre 732.30
17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 metre 795.60
17.36 Providing and filling the joints with spun yarn, cement slurry and cement
mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes :
17.36.1 75 mm dia pipe each 43.70
17.36.2 100 mm dia pipe each 51.50
17.37 Providing and fixing M.S. holder-bat clamps of approved design to Sand
Cast iron/cast iron (spun) pipe embedded in and including cement
concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size),including cost of cutting
holes and making good the walls etc. :
17.37.1 For 100 mm dia pipe each 103.90
17.37.2 For 75 mm dia pipe each 101.40

169 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
17.38 Providing and fixing bend of required degree with access door, insertion
rubber washer 3 mm thick, bolts and nuts complete.
17.38.1 100 mm dia
17.38.1.1 Sand cast iron S&S as per IS - 1729 each 357.50
17.38.1.2 Sand cast iron S&S as per IS - 3989 each 403.90
17.38.2 75 mm dia
17.38.2.1 Sand cast iron S&S as per IS - 1729 each 284.70
17.38.2.2 Sand cast iron S&S as per IS- 3989 each 348.20
17.39 Providing and fixing plain bend of required degree.
17.39.1 100 mm dia
17.39.1.1 Sand cast iron S&S as per IS - 1729 each 455.20
17.39.1.2 Sand cast iron S&S as per IS : 3989 each 351.40
17.39.2 75 mm dia
17.39.2.1 Sand cast iron S&S as per IS -1729 each 229.80
17.39.2.2 Sand cast iron S&S as per IS - 3989 each 260.30
17.40 Providing and fixing heel rest sanitary bend
17.40.1 100 mm dia
17.40.1.1 Sand cast iron S&S as per IS - 1729 each 333.10
17.40.1.2 Sand cast iron S&S as per IS - 3989 each 389.20
17.40.2 75 mm dia
17.40.2.1 Sand cast iron S&S as per IS - 1729 each 290.80
17.40.2.2 Sand cast iron S&S as per IS - 3989 each 327.50
17.41 Providing and fixing double equal junction of required degree with
access door, insertion rubber washer 3 mm thick, bolts and nuts
complete :
17.41.1 100x100x100x100 mm
17.41.1.1 Sand cast iron S&S as per IS - 1729 each 721.00
17.41.1.2 Sand cast iron S&S as per IS - 3989 each 800.30
17.41.2 75x75x75x75 mm
17.41.2.1 Sand cast iron S&S as per IS - 1729 each 559.40
17.41.2.2 Sand cast iron S&S as per IS - 3989 each 626.50
17.42 Providing and fixing double equal plain junction of required degree.

17.42.1 100x100x100x100 mm
17.42.1.1 Sand cast iron S&S as per IS - 1729 each 662.70
17.42.1.2 Sand cast iron S&S as per IS - 3989 each 784.70
17.42.2 75x75x75x75 mm
17.42.2.1 Sand cast iron S&S as per IS - 1729 each 444.60
17.42.2.2 Sand cast iron S&S as per IS - 3989 each 586.20
17.43 Providing and fixing single equal plain junction of required degree with
access door, insertion rubber washer 3 mm thick, bolts and nuts
complete.
17.43.1 100x100x100 mm
17.43.1.1 Sand cast iron S&S as per IS - 1729 each 508.90
17.43.1.2 Sand cast iron S&S as per IS - 3989 each 654.10
17.43.2 75x75x75 mm
17.43.2.1 Sand cast iron S&S as per IS - 1729 each 379.90
17.43.2.2 Sand cast iron S&S as per IS - 3989 each 495.90

BCD/SOR_8th Edition_October 2016 170

Code
Description Unit Rate Rs.
No.
17.44 Providing and fixing single equal plain junction of required degree :

17.44.1 100x100x100 mm
17.44.1.1 Sand cast iron S&S as per IS - 1729 each 577.20
17.44.1.2 Sand cast iron S&S as per IS - 3989 each 604.10
17.44.2 75x75x75 mm
17.44.2.1 Sand cast iron S&S as per IS - 1729 each 345.80
17.44.2.2 Sand cast iron S&S as per IS - 3989 each 425.10
17.45 Providing and fixing double unequal junction of required degree with
access door, insertion rubber washer 3 mm thick, bolts and nuts
complete :
17.45.1 100x100x75x75 mm
17.45.1.1 Sand cast iron S&S as per IS - 1729 each 721.30
17.45.1.2 Sand cast iron S&S as per IS - 3989 each 1087.50
17.46 Providing and fixing double unequal plain junction of required degree :

17.46.1 100x100x75x75 mm
17.46.1.1 Sand cast iron S&S as per IS - 1729 each 699.30
17.46.1.2 Sand cast iron S&S as per IS - 3989 each 1004.50
17.47 Providing and fixing single unequal junction of required degree with
access door, insertion rubber washer 3 mm thick, bolts and nuts
complete :
17.47.1 100x100x75 mm
17.47.1.1 Sand cast iron S&S as per IS - 1729 each 538.20
17.47.1.2 Sand cast iron S&S as per IS - 3989 each 831.10
17.48 Providing and fixing single unequal plain junction of required degree :

17.48.1 100x100x75 mm
17.48.1.1 Sand cast iron S&S as per IS - 1729 each 479.60
17.48.1.2 Sand cast iron S&S as per IS - 3989 each 723.70
17.49 Providing and fixing double equal plain invert branch of required degree:

17.49.1 100x100x100x100 mm
17.49.1.1 Sand cast iron S&S as per IS - 1729 each 699.30
17.49.1.2 Sand cast iron S&S as per IS 3989 each 674.90
17.49.2 75x75x75x75 mm
17.49.2.1 Sand cast iron S&S as per IS - 1729 each 522.80
17.49.2.2 Sand cast iron S&S as per IS - 3989 each 541.10
17.50 Providing and fixing single equal plain invert branch of required degree :

17.50.1 100x100x100 mm
17.50.1.1 Sand cast iron S&S as per iron 1729 each 528.40
17.50.1.2 Sand cast iron S&S as per IS - 3989 each 546.70
17.50.2 75x75x75 mm
17.50.2.1 Sand cast iron S&S as per IS - 1729 each 412.90
17.50.2.2 Sand cast iron S&S as per IS - 3989 each 416.60
17.51 Providing and fixing double unequal invert branch of required degree :

17.51.1 100x100x75x75 mm
17.51.1.1 Sand cast iron S&S as per IS - 1729 each 723.70
17.51.1.2 Sand cast iron S&S as per IS - 3989 each 912.90

171 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
17.52 Providing and fixing single unequal plain invert branch of required
degree :
17.52.1 100x100x75 mm
17.52.1.1 Sand cast iron S&S as per IS - 1729 each 632.20
17.52.1.2 Sand cast iron S&S as per IS - 3989 each 693.20
17.53 Providing and fixing sand cast iron S&S off sets as per IS: 1729
17.53.1 76 mm off sets
17.53.1.1 With 75 mm dia pipe each 288.40
17.53.1.2 With 100 mm dia pipe each 465.40
17.53.2 114 mm off sets
17.53.2.1 With 75 mm dia pipe each 394.10
17.53.2.2 With 100 mm dia pipe each 495.40
17.53.3 152 mm off sets
17.53.3.1 With 75 mm dia pipe each 474.00
17.53.3.2 With 100 mm dia pipe each 604.70
17.54 Providing and fixing sand cast iron S&S off sets as per IS: 3989 :

17.54.1 75 mm off sets

17.54.1.1 With 75 mm dia pipe each 296.90
17.54.2 150 mm off sets
17.54.2.1 With 75 mm dia pipe each 381.20
17.54.2.2 With 100 mm dia pipe each 509.40
17.55 Providing and fixing door piece, insertion rubber washer 3mm thick,bolts
& nuts complete :
17.55.1 100 mm
17.55.1.1 Sand cast iron S&S as per IS - 1729 each 538.20
17.55.1.2 Sand cast iron S&S as per IS - 3989 each 538.20
17.55.2 75 mm
17.55.2.1 Sand cast iron S&S as per IS - 1729 each 376.30
17.55.2.2 Sand cast iron S&S as per IS - 3989 each 376.30
17.56 Providing and fixing terminal guard :
17.56.1 100 mm
17.56.1.1 Sand cast iron S&S as per IS - 1729 each 259.80
17.56.1.2 Sand cast iron S&S as per IS - 3989 each 455.20
17.56.2 75 mm
17.56.2.1 Sand cast iron S&S as per IS - 1729 each 206.60
17.56.2.2 Sand cast iron S&S as per IS - 3989 each 388.50
17.57 Providing and fixing collar :
17.57.1 100 mm
17.57.1.1 Sand cast iron S&S as per IS - 1729 each 202.50
17.57.1.2 Sand cast iron S&S as per IS - 3989 each 333.10
17.57.2 75 mm
17.57.2.1 Sand cast iron S&S as per IS - 1729 each 160.20
17.57.2.2 Sand cast iron S&S as per IS - 3989 each 229.80
17.58 Providing lead caulked joints to sand cast iron/centrifugally cast (spun)
iron pipes and fittings of diameter :
17.58.1 100 mm each 207.80
17.58.2 75 mm each 177.10
17.58.3 50 mm each 142.20

BCD/SOR_8th Edition_October 2016 172

Code
Description Unit Rate Rs.
No.
17.59 Providing and fixing M.S. stays and clamps for sand cast
iron/centrifugally cast (spun) iron pipes of diameter :
17.59.1 100 mm each 70.60
17.59.2 75 mm each 58.90
17.59.3 50 mm each 53.80
17.60 Providing and fixing trap of self cleansing design with screwed down or
hinged grating with or without vent arm complete, including cost of
cutting and making good the walls and floors :

17.60.1 100 mm inlet and 100 mm outlet

17.60.1.1 Sand cast iron S&S as per IS: 3989 each 849.00
17.60.1.2 Sand Cast Iron S&S as per IS: 1729 each 653.70
17.60.2 100 mm inlet and 75 mm outlet
17.60.2.1 Sand cast iron S&S as per IS - 3989 each 889.30
17.60.2.2 Sand Cast Iron S&S as per IS- 1729 each 584.10
17.61 Cutting chases in brick masonry walls for following diameter sand cast
iron/ centrifugally cast (spun) iron pipes and making good the same
with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone
aggregate 12.5 mm nominal size), including necessary plaster and
pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :

17.61.1 100 mm dia metre 226.80

17.61.2 75 mm dia metre 162.80
17.61.3 50 mm dia metre 104.30
17.62 Painting C.I. cistern with bitumastic or any other anti-corrosive paint each 329.10
inside and white paint over a coat of zinc chromate yellow primer (of
approved quality ) .on the outside surface of the cistern, flush pipe,other
fittings, etc. complete for new work
17.63 Re-painting C.I. cistern with bitumastic or any other anti-corrosive paint each 241.80
inside and white paint on the outside surface of the cistern, flush pipe,
other fittings, etc. complete, including polishing of wooden seat and lid
and cleaning of W.C. pan with acid wherever necessary.

17.64 Repainting C.I. cistern with synthetic enamel paint of approved each 99.70
colour,brand and manufacture on the outside surface of cistern, flush
pipe, other fittings etc. complete.
17.65 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent
pipes and fittings with two coats of synthetic enamel paint of any colour
such as chocolate grey, or buff etc. over a coat of primer
(of approved quality) for new work :

17.65.1 100 mm diameter pipe metre 30.20

17.65.2 75 mm diameter pipe metre 23.10
17.66 Repainting sand cast iron/ centrifugally cast iron (spun) iron, soil,waste,
vent pipes and fittings with one coat of synthetic enamel paint of any
colour such as chocolate, grey or buff etc :

17.66.1 100 mm diameter pipe metre 14.60

17.66.2 75 mm diameter pipe metre 10.90

173 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
17.67 Repainting bath tub of size 1700x730x430 mm with enamel paint. each 334.30
17.68 Providing and fixing vitreous china dual purpose closet suitable for use
as squatting pan or European type water closet (Anglo Indian W.C pan)
with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre
low level flushing cistern with fitting and brackets,40 mm flush bend, 20
mm over flow pipe, with specials of standard make and mosquito proof
coupling of approved municipal design complete, including painting of
fittings and brackets, cutting and making good the walls and floors
wherever required :
17.68.1 White vitreous china dual purpose WC pan with white solid each 6176.10
plastic seat and lid with white vitreous china flushing cistern
and C.P. flush bend.
17.69 Providing and fixing PTMT Waste Coupling for wash basin and sink,of
approved quality and colour.
17.69.1 Waste coupling 31 mm dia of 79 mm length and 62mm each 104.10
breadth weighing not less than 45 gms
17.69.2 Waste coupling 38 mm dia of 83 mm length and 77mm each 120.00
breadth, weighing not less than 60 gms
17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.
17.70.1 Bottle t rap 31mm single piece moulded with height of 270 each 428.80
mm, effective length of tail pipe 260 mm from the centre of
the waste coupling, 77 mm breadth with 25 mm minimum
water seal, weighing not less than 260 gms
17.70.2 Bottle trap 38 mm single piece moulded with height of 270 each 463.00
mm, effective length of tail pipe 260 mm from the centre of
the waste coupling, 77 mm breadth with 25 mm minimum
water seal, weighing not less than 263 gms
17.71 Providing and fixing PTMT liquid soap container 109 mm wide,125 mm each 191.00
high and 112 mm distance from wall of standard shape with bracket of
the same materials with snap fittings of approved quality and colour,
weighing not less than 105 gms.
17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, each 183.50
200 mm wide with minimum distances of 37 mm from wall face with
concealed fittings arrangement of approved quality and colour,weighing
not less than 88 gms.
17.73 Providing and fixing PTMT towel rail complete with brackets fixed to
wooden cleats with CP brass screws with concealed fittings
arrangement of approved quality and colour.
17.73.1 450 mm long towel rail with total length of 495 mm,78 mm each 377.60
wide and effective height of 88 mm, weighing not less than
170 gms
17.73.2 600 mm long towel rail with total length of 645 mm, width each 419.10
78 mm and effective height of 88 mm, weighing not less
than 190 gms
17.74 Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 each 458.20
mm height of approved quality and colour, weighing not less than 300
gms.

BCD/SOR_8th Edition_October 2016 174

Code
Description Unit Rate Rs.
No.
17.75 Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm each 169.00
with 1/2" BSP thread and shapes, weighing not less than 60 gms.
17.76 Providing and fixing PTMT urinal cock of approved quality and colour.
17.76.1 15 mm nominal bore, 80 mm long, 42 mm high and 30mm each 163.10
wide with BSP female threads weighing not less than 48 gms
17.77 Providing and fixing M.S. holder bat clamp of approved design to sand
cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made
of 50x5 mm flat of specified shape, projecting 75 mm outside the wall
surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners,
including drilling necessary holes in brick wall/ CC/ RCC surface and the
cost of bolts etc. The pipes shall be fixed to the already fixed brackets
with the help of 30 mm x1.6 mm galvanised M.S. flats of specified
shape and of total length 420 mm and shall be fixed with M.S. nuts,
bolts, & washers of size 25x6 mm, one bolts on each side of the pipe.
17.77.1 Total bracket length 580 mm of approved shape and design each 171.60
(for single 100 mm dia pipe)
17.77.2 Total bracket length 810 mm of approved shape and design each 205.00
(for two 100 mm dia pipes)
17.77.3 Total bracket length 1040 mm of approved shape and design each 238.40
(for three 100 mm dia pipes)
17.78 Providing and fixing white vitreous china extended wall mounting water each 10052.00
closet of size 780x370x690 mm of approved shape including providing
& fixing white vitreous china cistern with dual flush fitting,of flushing
capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover,
and cistern fittings, nuts, bolts and gasket etc complete.
17.79 Providing & fixing white vitreous china water less urinal of size 600 x 330 each 22767.90
x 315 mm having antibacterial /germs free ceramic surface,fixed with
cartridge having debris catcher and hygiene seal.
17.80 Providing and fixing white vitreous china battery based infrared sensor each 17396.90
operated urinal of approx. size 610 x 390 x 370 mm having pre &post
flushing with water (250 ml & 500 ml consumption), having water inlet
from back side, including fixing to wall with suitable brackets all as per
manufacturers specification and direction of Engineer-in-charge.

175 BCD/SOR_8th Edition_October 2016

SUB HEAD : 18.0
WATER SUPPLY
 BUILDING WORK - Contd.

18.0 Water Supply

Code Description Unit Rate Rs.
No.
PE - AL - PE COMPOSITE PRESSURE PIPES
18.1 Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-
ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V.
stabilized with carbon black having thermal stability for hot & cold
water supply, capable to withstand temperature up to 80 0C,
including all special fittings of composite material (engineering
plastic blend and brass inserts wherever required) e.g. elbows, tees,
reducers, couplers & connectors etc., with clamps at 1.00 metre
spacing. This includes testing of joints complete as per direction of
the Engineer in charge.
Internal work - Exposed on wall
18.1.1 1216 (16 mm OD) pipe metre 197.50
18.1.2 1620 (20 mm OD) pipe metre 249.80
18.1.3 2025 (25 mm OD) pipe metre 310.00
18.1.4 2532 (32 mm OD) pipe metre 389.40
18.1.5 3240 (40 mm OD) pipe metre 621.50
18.1.6 4050 (50 mm OD) pipe metre 677.10
18.2 Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-
ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V.
stabilized with carbon black having thermal stability for hot & cold
water supply, capable to withstand temperature up to 80 0C,
including all special fittings of composite material (engineering
plastic blend and brass inserts wherever required) e.g. elbows, tees,
reducers, couplers & connectors etc., with clamps at 1.00 metre
spacing. This includes the costs of cutting chases and including
testing of joints complete as per direction of the engineer in charge.
Concealed work, including cutting chases and making good the wall
etc.
18.2.1 1216 (16 mm OD) pipe metre 306.90
18.2.2 1620 (20 mm OD) pipe metre 370.90
18.2.3 2025 (25 mm OD) pipe metre 445.70
18.2.4 2532 (32 mm OD) pipe metre 541.80
18.3 Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-
ALPE) Composite Pressure Pipes conforming to IS - 15450,
U.V.stabilized with carbon black having thermal stability for hot &
cold water supply, capable to withstand temperature up to 80 0C,
including all special fittings of composite material (engineering
plastic blend and brass inserts wherever required) e.g. elbows, tees,
reducers, couplers & connectors etc., with trenching, refilling and
testing of joints complete as per direction of the engineer in charge.
External work
18.3.1 1216 (16 mm OD) pipe metre 190.10
18.3.2 1620 (20 mm OD ) pipe metre 237.70
18.3.3 2025 (25 mm OD ) pipe metre 293.30
18.3.4 2532 (32 mm OD ) pipe metre 364.70
18.3.5 3240 (40 mm OD ) pipe metre 585.70
18.3.6 4050 (50 mm OD ) pipe metre 641.20
PP- R PIPES

176 BCD/SOR_8th Edition_October 2016

 Code Description Unit Rate Rs.
No.
18.4 Providing and fixing 3 layer PP-R (Poly propylene Random
copolymer) pipes SDR 7.4, U V stabilized & anti - microbial fusion
welded, having thermal stability for hot & cold water supply,
including all PP - R plain & brass threaded polypropylene random
fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This
includes testing of joints complete as per direction of Engineer in
Charge.
Internal work - Exposed on wall
18.4.1 PN - 16 Pipe, 16 mm OD metre 105.50
18.4.2 PN - 16 Pipe, 20 mm OD metre 141.90
18.4.3 PN - 16 Pipe, 25 mm OD metre 195.70
18.4.4 PN - 16 Pipe, 32 mm OD metre 289.50
18.4.5 PN - 16 Pipe, 40 mm OD metre 420.00
18.4.6 PN - 16 Pipe, 50 mm OD metre 610.40
18.5 Providing and fixing 3 layer PP-R (Poly propylene Random
copolymer) pipes SDR 7.4, U V stabilized & anti - microbial fusion
welded, having thermal stability for hot & cold water supply,
including all PP - R plain & brass threaded polypropylene random
fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This
includes the cost of cutting chases and making good the same
including testing of joints complete as per direction of Engineer in
Charge.
Concealed work, including cutting chases and making good the
walls etc.,
18.5.1 PN - 16 Pipe, 16 mm OD metre 183.00
18.5.2 PN - 16 Pipe, 20 mm OD metre 225.70
18.5.3 PN - 16 Pipe, 25 mm OD metre 291.90
18.5.4 PN - 16 Pipe, 32 mm OD metre 407.30
18.6 Providing and fixing 3 layer PP-R (Poly propylene Random
copolymer) pipes, U V stabilized & anti - microbial fusion welded,
having thermal stability for hot & cold water supply, including all PP -
R plain & brass threaded polypropylene random fittings, including
trenching, refilling & testing of joints complete as per direction of
Engineer in Charge.
External work
18.6.1 PN - 16 Pipe, 16 mm OD (SDR - 7.4) metre 98.10
18.6.2 PN - 16 Pipe, 20 mm OD (SDR - 7.4) metre 126.30
18.6.3 PN - 16 Pipe, 25 mm OD (SDR - 7.4) metre 182.50
18.6.4 PN - 16 Pipe, 32 mm OD (SDR - 7.4) metre 268.20
18.6.5 PN - 16 Pipe, 40 mm OD (SDR - 7.4) metre 384.10
18.6.6 PN - 16 Pipe, 50 mm OD (SDR - 7.4) metre 574.60
18.6.7 PN - 16 Pipe, 63 mm OD (SDR - 7.4) metre 871.20
18.6.8 PN - 16 Pipe, 75 mm OD (SDR - 7.4) metre 1167.90
18.6.9 PN - 16 Pipe, 90 mm OD (SDR - 7.4) metre 1767.20
18.6.10 PN - 10 Pipe, 110 mm OD (SDR - 11) metre 1979.80
18.6.11 PN - 10 Pipe, 160 mm OD (SDR - 11) metre 4083.50
C.P.V.C. PIPES

BCD/SOR_8th Edition_October 2016 177

Code Description Unit Rate Rs.
No.
18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,
having thermal stability for hot & cold water supply, including all
CPVC plain & brass threaded fittings, including fixing the pipe with
clamps at 1.00 m spacing. This includes jointing of pipes & fittings
with one step CPVC solvent cement and testing of joints complete as
per direction of Engineer in Charge.
Internal work - Exposed on wall
18.7.1 15 mm nominal outer dia Pipes metre 138.70
18.7.2 20 mm nominal outer dia Pipes metre 164.00
18.7.3 25 mm nominal outer dia Pipes metre 206.80
18.7.4 32 mm nominal outer dia Pipes metre 270.40
18.7.5 40 mm nominal outer dia Pipes metre 375.60
18.7.6 50 mm nominal outer dia Pipes metre 558.10
18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,
having thermal stability for hot & cold water supply, including all
CPVC plain & brass threaded fittings, including fixing the pipe with
clamps at 1.00 m spacing. This includes jointing of pipes & fittings
with one step CPVC solvent cement and testing of joints complete as
per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the
walls etc.
18.8.1 15 mm nominal outer dia Pipes metre 221.40
18.8.2 20 mm nominal outer dia Pipes metre 249.20
18.8.3 25 mm nominal outer dia Pipes metre 306.90
18.8.4 32 mm nominal outer dia Pipes metre 381.60
18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,
having thermal stability for hot & cold water supply including all
CPVC plain & brass threaded fittings This includes jointing of pipes
& fittings with one step CPVC solvent cement ,trenching ,refilling &
testing of joints complete as per direction of Engineer in Charge.
External work
18.9.1 15 mm nominal outer dia Pipes metre 126.60
18.9.2 20 mm nominal outer dia Pipes metre 147.30
18.9.3 25 mm nominal outer dia Pipes metre 193.60
18.9.4 32 mm nominal outer dia Pipes metre 249.10
18.9.5 40 mm nominal outer dia Pipes metre 339.70
18.9.6 50 mm nominal outer dia Pipes metre 522.20
18.9.7 62.50 mm nominal inner dia Pipes metre 1501.20
18.9.8 75 mm nominal inner dia Pipes metre 2120.10
18.9.9 100 mm nominal inner dia Pipes metre 2932.00
18.9.10 150 mm nominal inner dia Pipes metre 3528.00
18.10 Providing and fixing G.I. pipes complete with G.I. fittings and
clamps, i/c cutting and making good the walls etc.
Internal work - Exposed on wall
18.10.1 15 mm dia nominal bore metre 167.90
18.10.2 20 mm dia nominal bore metre 207.70
18.10.3 25 mm dia nominal bore metre 269.20
18.10.4 32 mm dia nominal bore metre 319.20
18.10.5 40 mm dia nominal bore metre 394.10
18.10.6 50 mm dia nominal bore metre 489.10

178 BCD/SOR_8th Edition_October 2016

 Code Description Unit Rate Rs.
No.
18.11 Providing and fixing G.I. Pipes complete with G.I. fittings and
clamps, i/c making good the walls etc. concealed pipe, including
painting with anti corrosive bitumastic paint, cutting chases and
making good the wall :
18.11.1 15 mm dia nominal bore metre 229.60
18.11.2 20 mm dia nominal bore metre 265.50
18.12 Providing and fixing G.I. pipes complete with G.I. fittings including
trenching and refilling etc.
External work
18.12.1 15 mm dia nominal bore metre 146.40
18.12.2 20 mm dia nominal bore metre 177.60
18.12.3 25 mm dia nominal bore metre 231.30
18.12.4 32 mm dia nominal bore metre 268.70
18.12.5 40 mm dia nominal bore metre 322.40
18.12.6 50 mm dia nominal bore metre 391.10
18.12.7 65 mm dia nominal bore metre 515.10
18.12.8 80 mm dia nominal bore metre 633.60
18.13 Making connection of G.I. distribution branch with G.I. main of
following sizes by providing and fixing tee, including cutting and
threading the pipe etc. complete :
18.13.1 25 to 40 mm nominal bore each 267.40
18.13.2 50 to 80 mm nominal bore each 637.80
18.14 Fixing water meter and stop cock in G.I. pipe line including cutting each 212.50
and threading the pipe and making long screws etc. complete (cost
of water meter and stop cock to be paid separately).
BRASS FITTINGS
18.15 Providing and fixing brass bib cock of approved quality :
18.15.1 15 mm nominal bore each 273.00
18.15.2 20 mm nominal bore each 294.20
18.16 Providing and fixing brass stop cock of approved quality :
18.16.1 15 mm nominal bore each 273.00
18.16.2 20 mm nominal bore each 361.40
18.17 Providing and fixing gun metal gate valve with C.I. wheel of
approved quality (screwed end) :
18.17.1 25 mm nominal bore each 449.50
18.17.2 32 mm nominal bore. each 525.70
18.17.3 40 mm nominal bore each 613.90
18.17.4 50 mm nominal bore each 811.40
18.17.5 65 mm nominal bore each 1351.60
18.17.6 80 mm nominal bore each 2016.50
18.18 Providing and fixing ball valve (brass) of approved quality, High or
low pressure, with plastic floats complete :
18.18.1 15 mm nominal bore each 300.90
18.18.2 20 mm nominal bore each 427.90
18.18.3 25 mm nominal bore each 469.40

BCD/SOR_8th Edition_October 2016 179

Code Description Unit Rate Rs.
No.
18.19 Providing and fixing gun metal non- return valve of approved quality
(screwed end) :
18.19.1 25 mm nominal bore
18.19.1.1 Horizontal each 430.80
18.19.1.2 Vertical each 467.40
18.19.2 32 mm nominal bore
18.19.2.1 Horizontal each 579.90
18.19.2.2 Vertical each 665.40
18.19.3 40 mm nominal bore
18.19.3.1 Horizontal each 716.90
18.19.3.2 Vertical each 948.80
18.19.4 50 mm nominal bore
18.19.4.1 Horizontal each 1037.20
18.19.4.2 Vertical each 1269.10
18.19.5 65 mm nominal bore
18.19.5.1 Horizontal each 1857.80
18.19.5.2 Vertical each 2126.30
18.19.6 80 mm nominal bore
18.19.6.1 Horizontal each 2629.80
18.19.6.2 Vertical each 3569.70
18.20 Providing and fixing brass ferrule with C.I. mouth cover including
boring and tapping the main :
18.20.1 15 mm nominal bore each 254.10
18.20.2 20 mm nominal bore each 281.80
18.20.3 25 mm nominal bore each 365.40
18.21 Providing and fixing uplasticised PVC connection pipe with brass
ions :
18.21.1 30 cm length
18.21.1.1 15 mm nominal bore each 61.80
18.21.1.2 20 mm nominal bore each 68.00
18.21.2 45 cm length
18.21.2.1 15 mm nominal bore each 70.60
18.21.2.2 20 mm nominal bore each 86.50
18.22 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
18.22.1 100 mm diameter each 75.00
18.22.2 150 mm diameter each 89.90
C.I/ DUCTILE IRON PIPES & SPECIALS
18.23 Laying in position centrifugally cast (spun) iron S&S or flanged quintal 89.60
pipes (excluding cost of pipe).
18.24 Laying in position S&S or flanged C.I. special such as tees, quintal 228.00
bends,collars, tapers and caps etc.(excluding cost of specials).
18.25 Providing and laying S&S C.I. standard specials such as tees,
bends,collars, tapers, caps etc. (Heavy class) :
18.25.1 Up to 300 mm dia quintal 4633.70
18.25.2 Over 300 mm dia quintal 4755.80

180 BCD/SOR_8th Edition_October 2016

 Code Description Unit Rate Rs.
No.
18.26 Providing and laying flanged C.I. standard specials such as
tees,bends, collars, tapers, caps etc., suitable for flanged jointing as
per IS : 1538 :
18.26.1 Up to 300 mm dia quintal 6953.00
18.26.2 Over 300 mm dia quintal 7319.20
18.27 Providing and laying S&S centrifugally cast (spun) iron pipes (Class
LA) conforming to IS - 1536 :
18.27.1 100 mm dia pipe metre 1119.10
18.27.2 125 mm dia pipe metre 1394.00
18.27.3 150 mm dia pipe metre 1681.40
18.27.4 200 mm dia pipe metre 2857.30
18.27.5 250 mm dia pipe metre 3729.60
18.27.6 300 mm dia pipe metre 5030.20
18.27.7 350 mm dia pipe metre 6031.10
18.27.8 400 mm dia pipe metre 7949.90
18.27.9 450 mm dia pipe metre 9626.50
18.27.10 500 mm dia pipe metre 11175.50
18.27.11 600 mm dia pipe metre 15631.90
18.28 Providing lead caulked joints to spun iron or C.I. pipes and specials,
including testing of joints but excluding the cost of pig lead :

18.28.1 100 mm diameter pipe each 142.8

18.28.2 125 mm diameter pipe each 209
18.28.3 150 mm diameter pipe each 214.4
18.28.4 200 mm diameter pipe each 283.7
18.28.5 250 mm diameter pipe each 354.4
18.28.6 300 mm diameter pipe each 427.7
18.28.7 350 mm diameter pipe each 446.1
18.28.8 400 mm diameter pipe each 576.9
18.28.9 450 mm diameter pipe each 645.7
18.28.10 500 mm diameter pipe each 684.20
18.28.11 600 mm diameter pipe each 916.90
18.29 Supplying pig lead at site of work. quintal 10997.30
18.30 Providing flanged joints to double flanged C.I./ D.I. pipes and
specials, including testing of joints :
18.30.1 80 mm diameter pipe each 106.10
18.30.2 100 mm diameter pipe each 179.70
18.30.3 125 mm diameter pipe each 182.20
18.30.4 150 mm diameter pipe each 217.10
18.30.5 200 mm diameter pipe each 223.20
18.30.6 250 mm diameter pipe each 340.70
18.30.7 300 mm diameter pipe each 346.80
18.30.8 350 mm diameter pipe each 481.10
18.30.9 400 mm diameter pipe each 705.20
18.30.10 450 mm diameter pipe each 876.20
18.30.11 500 mm diameter pipe each 1001.30
18.30.12 600 mm diameter pipe each 1177.40
C.I. SLUICE VALVES/ FIRE HYDRANTS & FIXTURES

BCD/SOR_8th Edition_October 2016 181

Code Description Unit Rate Rs.
No.
18.31 Providing and fixing C.I. sluice valves (with cap) complete with
bolts,nuts, rubber insertions etc. (the tail pieces if required will be paid
separately) :
18.31.1 100 mm diameter
18.31.1.1 Class I each 3407.30
18.31.1.2 Class II each 4046.30
18.31.2 125 mm diameter
18.31.2.1 Class I each 3672.80
18.31.2.2 Class II each 4800.10
18.31.3 150 mm diameter
18.31.3.1 Class I each 5002.00
18.31.3.2 Class II each 5890.00
18.31.4 200 mm diameter
18.31.4.1 Class I each 9892.30
18.31.4.2 Class II each 12048.90
18.31.5 250 mm diameter
18.31.5.1 Class I each 14515.00
18.31.5.2 Class II each 2494.70
18.31.6 300 mm diameter
18.31.6.1 Class I each 20194.20
18.31.6.2 Class II each 24002.20
18.32 Constructing masonry Chamber 30x30x50 cm inside, in brick work in
cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I.
surface box 100x100 x75 mm (inside) with hinged cover fixed in
cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size), i/c necessary excavation,
foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone
aggregate 40mm nominal size ) and inside plastering with cement
mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a
floating coat of neat cement complete as per standard design :

18.32.1 With common burnt clay F.P.S.(non modular) bricks of each 1018.40
class designation 100A
18.33 Constructing masonry Chamber 60x60x75 cm inside, in brick work in
cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,with C.I.
surface box 100mm top diameter, 160 mm bottom diameter and 180
mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1
cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size
) , i/c necessary excavation, foundation concrete 1:5:10(1 cement : 5
fine sand : 10 graded stone aggregate 40 mm nominalsize) and inside
plastering with cement mortar 1:3 (1 cement : 3coarse sand) 12 mm
thick, finished with a floating coat of neat cement complete as per
standard design :
18.33.1 With common burnt clay F.P.S.(non modular) bricks of class each 5807.50
designation 100A

182 BCD/SOR_8th Edition_October 2016

 Code Description Unit Rate Rs.
No.
18.34 Constructing masonry Chamber 60x60x75 cm inside, in brick work in
cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,with C.I.
surface box 100mm top diameter, 160 mm bottom diameter and 180
mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1
cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size
) , i/c necessary excavation, foundation concrete 1:5:10(1 cement : 5
fine sand : 10 graded stone aggregate 40 mm nominalsize) and inside
plastering with cement mortar 1:3 (1 cement : 3coarse sand) 12 mm
thick, finished with a floating coat of neat cement complete as per
standard design :
18.34.1 With common burnt clay F.P.S.(non modular) bricks of class each 10657.50
designation 100A
18.35 Constructing masonry Chamber 120x120x100 cm inside, in brick work
in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with
C.I. surface box 100 mm top diameter, 160 mm bottom diameter and
180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1
cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal
size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement :
5 fine sand : 10 graded stone aggregate 40 mm nominal size) and
inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12
mm thick, finished with a floating coat of neat cement complete as per
standard design :
18.35.1 With common burnt clay F.P.S.(non modular) bricks of class each 14598.40
designation 100A
18.36 Constructing masonry Chamber 60x60x75 cm, inside in brick work in
cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants,with C.I.
surface box 350x350 mm top and 165 mm deep ( inside)with chained
lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size) , i/c necessary excavation,
foundation concrete 1:5:10 (1 cement : 5 fine sand:10 graded stone
aggregate 40 mm nominal size) and inside plastering with cement
mortar 1:3 (1 cement : 3 coarse sand)12 mm thick, finished with a
floating coat of neat cement complete as per standard design :

18.36.1 With common burnt clay F.P.S.(non modular) bricks of class each 5917.10
designation 100A
18.37 Constructing masonry Chamber 60x45x50 cm inside, in brick work in
cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete
with C.I. double flap surface box 400x200x200 mm (inside)with locking
arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal size) , i/c necessary
excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10
graded stone aggregate 40 mm nominal size) and inside plastering
with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick,
finished with a floating coat of neat cement complete as per standard
design :
18.37.1 With common burnt clay F.P.S.(non modular) bricks of class each 5229.80
designation 100A

BCD/SOR_8th Edition_October 2016 183

Code Description Unit Rate Rs.
No.
18.38 Painting G.I. pipes and fittings with synthetic enamel white paint with
two coats over a ready mixed priming coat, both of approved quality
for new work :
18.38.1 15 mm diameter pipe metre 8.00
18.38.2 20 mm diameter pipe metre 9.30
18.38.3 25 mm diameter pipe metre 12.30
18.38.4 32 mm diameter pipe metre 14.40
18.38.5 40 mm diameter pipe metre 17.20
18.38.6 50 mm diameter pipe metre 20.10
18.39 Repainting G.I. pipes and fittings with synthetic enamel white paint
with one coat of approved quality :
18.39.1 15 mm diameter pipe metre 4.00
18.39.2 20 mm diameter pipe metre 4.60
18.39.3 25 mm diameter pipe metre 5.90
18.39.4 32 mm diameter pipe metre 6.90
18.39.5 40 mm diameter pipe metre 8.10
18.39.6 50 mm diameter pipe metre 9.40
18.40 Painting G.I. pipes and fittings with two coats of anti-corrosive
bitumastic paint of approved quality :
18.40.1 15 mm diameter pipe metre 4.50
18.40.2 20 mm diameter pipe metre 5.30
18.40.3 25 mm diameter pipe metre 6.80
18.40.4 32 mm diameter pipe metre 7.90
18.40.5 40 mm diameter pipe metre 9.00
18.40.6 50 mm diameter pipe metre 10.60
18.40.7 65 mm diameter pipe metre 13.00
18.40.8 80 mm diameter pipe metre 15.00
18.41 Providing and filling sand of grading zone V or coarser grade, allround
the G.I. pipes in external work :
18.41.1 15 mm diameter pipe metre 14.50
18.41.2 20 mm diameter pipe metre 14.70
18.41.3 25 mm diameter pipe metre 15.10
18.41.4 32 mm diameter pipe metre 15.50
18.41.5 40 mm diameter pipe metre 15.70
18.41.6 50 mm diameter pipe metre 16.30
18.41.7 65 mm diameter pipe metre 25.70
18.41.8 80 mm diameter pipe metre 26.50
18.41.9 100 mm diameter pipe metre 28.00
18.41.10 150 mm diameter pipe metre 41.70
18.42 Boring with 100 mm diameter casing pipe for hand pump / tubewell, in
all soils except ordinary hard rocks requiring blasting, including
removing the casing pipe after the hand pump / tube well is lowered
and tested :
18.42.1 Up to 6 metres depth metre 239.80
18.42.2 Beyond 6 m and up to 12 m depth metre 285.30
18.42.3 Beyond 12 m and up to 18 m depth metre 333.00
18.43 Providing and placing in position filters of 40 mm diameter G.I. pipe metre 581.70
with brass strainer of approved quality.

18.44 Providing and fixing to filter and lowering to proper levels 40 mm metre 306.30
G.I.pipe for tube well including cleaning and priming the tube well.

184 BCD/SOR_8th Edition_October 2016

 Code Description Unit Rate Rs.
No.
18.45 Providing and placing in position hand pump of approved quality for each 912.30
40 mm diameter G.I. pipe complete with all accessories.
18.46 Providing and fixing G.I. Union in G.I. pipe including cutting and
threading the pipe and making long screws etc. complete (New work) :
18.46.1 15 mm nominal bore each 134.00
18.46.2 20 mm nominal bore each 158.40
18.46.3 25 mm nominal bore each 170.60
18.46.4 32 mm nominal bore each 213.30
18.46.5 40 mm nominal bore each 292.70
18.46.6 50 mm nominal bore each 358.40
18.46.7 65 mm nominal bore each 614.70
18.46.8 80 mm nominal bore each 712.40
18.47 Providing and fixing G.I. Union in existing G.I. pipe line, cutting and
threading the pipe and making long screws, including
excavation,refilling the earth or cutting of wall and making good the
same complete wherever required :
18.47.1 15 mm nominal bore each 260.20
18.47.2 20 mm nominal bore each 284.60
18.47.3 25 mm nominal bore each 296.80
18.47.4 32 mm nominal bore each 328.30
18.47.5 40 mm nominal bore each 407.70
18.47.6 50 mm nominal bore each 515.20
18.47.7 65 mm nominal bore each 771.50
18.47.8 80 mm nominal bore each 869.20
18.48 Providing and placing on terrace (at all floor levels) polyethylene water per litre 6.60
storage tank, ISI : 12701 marked, with cover and suitable locking
arrangement and making necessary holes for inlet, outlet and overflow
pipes but without fittings and the base support for tank.
C.P. BRASS F ITTINGS
18.49 Providing and fixing C.P. brass bib cock of approved quality each 481.60
conforming to IS:8931 :
18.50 Providing and fixing C.P. brass long nose bib cock of approved quality
conforming to IS standards and weighing not less than 810 gms.

18.50.1 15 mm nominal bore each 835.60

18.51 Providing and fixing C.P. brass long body bib cock of approved quality
conforming to IS standards and weighing not less than 690 gms.

18.51.1 15 mm nominal bore each 640.30

18.52 Providing and fixing C.P. brass stop cock (concealed) of standard
design and of approved make conforming to IS:8931.
18.52.1 15 mm nominal bore each 650.10
18.53 Providing and fixing C.P. brass angle valve for basin mixer and geyser
points of approved quality conforming to IS:8931 a) 15 mm nominal
bore
18.53.1 15 mm nominal bore each 532.40
PTMT FITTINGS

BCD/SOR_8th Edition_October 2016 185

Code Unit Rate Rs.
Description
No.
18.54
Providing and fixing PTMT bib cock of approved quality and colour.

18.54.1 15mm nominal bore, 86 mm long, weighing not less than 88 gms each 138.70
each 187.50
18.54.2 15 mm nominal bore, 122mm long, weighing not less than 99 gms
15 mm nominal bore, 165 mm long, weighing not less than 110 each 212.00
18.54.3
gms
18.54.4 15mm nominal bore, 90 mm long, weighing not less than 93 gms each 193.70
18.55
Providing and fixing PTMT stop cock of approved quality and colour.

18.55.1 15 mm nominal bore, 86 mm long, weighing not less than 88 gms each 138.70
18.55.2 20 mm nominal bore, 89 mm long, weighing not less than 88 gms each 175.30
Concealed stop cock, 15 mm nominal bore, 108 mm each 209.50
18.55.3
long,weighing not less than 108 gms
18.56
Providing and fixing PTMT pillar cock of approved quality and colour .
15 mm nominal bore, 107 mm long, weighing not less than 110 each 214.90
18.56.1
gms
15 mm nominal bore, 125 mm long foam flow, weighing not less each 294.20
18.56.2
than 120 gms
18.57
Providing and fixing PTMT, push cock of approved quality and colour.

18.57.1 15 mm nominal bore, 98 mm long, weighing not less than 75 gms each 126.50
18.57.2 15 mm nominal bore, 80 mm long, weighing not less than 46 gms each 114.30
18.58 Providing and fixing PTMT grating of approved quality and colour.
18.58.1 Circular type
18.58.1.1 100 mm nominal dia each 46.40
18.58.1.2 125 mm nominal dia with 25 mm waste hole each 59.90
18.58.2 Rectangular type with openable circular lid
150 mm nominal size square 100 mm diameter of the inner each 157.50
18.58.2.1
hinged round grating
AIR VALVE & WATER METER (BULK TYPE)
18.59 Providing and fixing C.I. double acting air valve of approved quality
with bolts, nuts, rubber insertions etc. complete (The tail pieces,tapers
etc if required will be paid separately) :
18.59.1 50 mm dia each 5002.40
18.59.2 80 mm dia each 6371.70
18.59.3 100 mm dia each 8496.60
18.60 Providing and fixing enclosed type water meter (bulk type) conforming
to IS : 2373 and tested by Municipal Board complete with bolts,nuts,
rubber insertions etc. (The tail pieces if required will be paid
separately) :
18.60.1 80 mm dia nominal bore each 3215.00
18.60.2 100 mm dia nominal bore each 4817.20
18.60.3 150 mm dia nominal bore each 7074.50
18.60.4 200 mm dia nominal bore each 7682.30

186 BCD/SOR_8th Edition_October 2016

 Code Unit Rate Rs.
Description
No.
18.61 Providing and fixing C.I. dirt box strainer for bulk type water meter with
nuts, bolts, rubber insertions etc. complete conforming to IS : 2373 :

18.61.1 80 mm dia each 3776.60

18.61.2 100 mm dia each 6111.30
18.61.3 150 mm dia each 7741.10
18.61.4 200 mm dia each 10839.30
18.62 Providing and fixing PTMT Ball cock of approved quality, colour and
make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D.
plastic ball.
15 mm nominal bore, 105 mm long, weighing not less than 138 each 208.10
18.62.1
gms
20 mm nominal bore, 120 mm long, weighing not less than 198 each 293.60
18.62.2
gms
25 mm nominal bore, 152mm long, weighing not less than 440 each 579.30
18.62.3
gms
40 mm nominal bore, 206mm long, weighing not less than 690 each 1018.70
18.62.4
gms
50 mm nominal bore, 242mm long, weighing not less than 1240 each 1470.40
18.62.5
gms
18.63 Providing and fixing PTMT angle stop cock 15 mm nominal each 175.30
bore,weighing not less than 85 gms
18.64 Providing and fixing PTMT swivelling shower, 15 mm nominal bore, each 120.20
weighing not less than 40 gms
18.65 Providing and fixing PTMT soap Dish Holder having length of each 160.40
138mm,breadth 102mm, height of 75mm with concealed fitting
arrangements,weighing not less than 106 gms.
18.66 Providing and laying S&S C.I. Standard specials such as tees,
bends,collars tapers and caps etc, suitable for flanged jointing as per
IS : 1538 :
18.66.1 Up to 300 mm dia quintal 6892.00
18.66.2 Above 300 mm dia quintal 10248.90
18.67 Providing and laying S&S C.I. Standard specials suitable for
mechanical jointing as per IS : 13382 :
18.67.1 Up to 300 mm dia quintal 11225.50
18.67.2 Above 300 mm dia quintal 11835.80
18.68 Providing and laying D.I. specials of class K-12 suitable for push-on
jointing as per IS : 9523 :
18.68.1 Up to 600 mm dia quintal 16108.30
18.68.2 Above 600 mm dia quintal 22211.80
18.69 Providing and laying D.I. Specials of Class K - 12 suitable for
mechanical jointing as per IS : 9523 :
18.69.1 Up to 600 mm dia quintal 16962.80
18.69.2 Above 600 mm dia quintal 24225.90

BCD/SOR_8th Edition_October 2016 187

Code Unit Rate Rs.
Description
No.
18.70 Providing push-on-joints to Centrifugally (Spun) Cast Iron Pipes or
Ductile Iron Pipes including testing of joints and the cost of rubber
gasket :
18.70.1 100 mm dia pipes joint 53.90
18.70.2 150 mm dia pipes joint 79.60
18.70.3 200 mm dia pipes joint 124.90
18.70.4 250 mm dia pipes joint 150.60
18.70.5 300 mm dia pipes joint 206.80
18.70.6 350 mm dia pipes joint 227.60
18.70.7 400 mm dia pipes joint 381.60
18.70.8 450 mm dia pipes joint 441.50
18.70.9 500 mm dia pipes joint 477.50
18.70.10 600 mm dia pipes joint 607.80
18.70.11 650 mm dia pipes joint 872.40
18.70.12 700 mm dia pipes joint 1012.80
18.70.13 800 mm dia pipes joint 1116.00
18.70.14 900 mm dia pipes joint 1442.20
18.70.15 1000 mm dia pipes joint 1708.50
18.71 Providing and laying Double Flanged (screwed / welded) Centrifugally
(Spun) Cast Iron, Class B (IS : 1536) :
18.71.1 100 mm dia C.I. Double Flanged Pipe metre 1705.40
18.71.2 150 mm dia C.I. Double Flanged Pipe metre 2668.70
18.71.3 200 mm dia C.I. Double Flanged Pipe metre 4214.80
18.71.4 250 mm dia C.I. Double Flanged Pipe metre 5092.00
18.71.5 300 mm dia C.I. Double Flanged Pipe metre 6508.10
18.71.6 350 mm dia C.I. Double Flanged Pipe metre 8196.60
18.71.7 400 mm dia C.I. Double Flanged Pipe metre 10611.40
18.71.8 450 mm dia C.I. Double Flanged Pipe metre 13516.80
18.71.9 500 mm dia C.I. Double Flanged Pipe metre 16793.60
18.71.10 600 mm dia C.I. Double Flanged Pipe metre 23277.5
18.72 Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes
conforming to IS : 8329 :
18.72.1 100 mm dia Ductile Iron Class K-7 pipes metre 962.60
18.72.2 150 mm dia Ductile Iron Class K-7 pipes metre 1392.20
18.72.3 200 mm dia Ductile Iron Class K-7 pipes metre 1926.50
18.72.4 250 mm dia Ductile Iron Class K-7 pipes metre 2609.20
18.72.5 300 mm dia Ductile Iron Class K-7 pipes metre 3596.50
18.72.6 350 mm dia Ductile Iron Class K-7 pipes metre 4282.70
18.72.7 400 mm dia Ductile Iron Class K-7 pipes metre 4996.20
18.72.8 450 mm dia Ductile Iron Class K-7 pipes metre 6035.20
18.72.9 500 mm dia Ductile Iron Class K-7 pipes metre 7126.70
18.72.10 600 mm dia Ductile Iron Class K-7 pipes metre 9300.70
18.72.11 700 mm dia Ductile Iron Class K-7 pipes metre 11949.5

188 BCD/SOR_8th Edition_October 2016

 Code Unit Rate Rs.
Description
No.
18.72 18.72.12 800 mm dia Ductile Iron Class K-7 pipes metre 15034.4
18.72.13 900 mm dia Ductile Iron Class K-7 pipes metre 19938.5
18.72.14 1000 mm dia Ductile Iron Class K-7 pipes metre 21194.3
18.72.15 100 mm dia Ductile Iron Class K-9 pipes metre 995.2
18.72.16 150 mm dia Ductile Iron Class K-9 pipes metre 1492.9
18.72.17 200 mm dia Ductile Iron Class K-9 pipes metre 2054
18.72.18 250 mm dia Ductile Iron Class K-9 pipes metre 2861.2
18.72.19 300 mm dia Ductile Iron Class K-9 pipes metre 3558.5
18.72.20 350 mm dia Ductile Iron Class K-9 pipes metre 4374.4
18.72.21 400 mm dia Ductile Iron Class K-9 pipes metre 5603
18.72.22 450 mm dia Ductile Iron Class K-9 pipes metre 6477.5
18.72.23 500 mm dia Ductile Iron Class K-9 pipes metre 8178.7
18.72.24 600 mm dia Ductile Iron Class K-9 pipes metre 9877
18.72.25 700 mm dia Ductile Iron Class K-9 pipes metre 13653.1
18.72.26 750 mm dia Ductile Iron Class K-9 pipes metre 15271.8
18.72.27 800 mm dia Ductile Iron Class K-9 pipes metre 14979
18.72.28 900 mm dia Ductile Iron Class K-9 pipes metre 18079.4
18.72.29 1000 mm dia Ductile Iron Class K-9 pipes metre 20329.4
18.73
Providing and laying Double Flanged (Screwed / Welded) Centrifugally
(Spun) Ductile Iron Pipes of Class K - 9 conforming to IS : 8329 :

18.73.1 100 mm dia Ductile Iron Double Flanged metre 2683.4

18.73.2 150 mm dia Ductile Iron Double Flanged metre 4306.2
18.73.3 200 mm dia Ductile Iron Double Flanged metre 5064.1
18.73.4 250 mm dia Ductile Iron Double Flanged metre 4244.7
18.73.5 300 mm dia Ductile Iron Double Flanged metre 8577.6
18.73.6 350 mm dia Ductile Iron Double Flanged metre 10842.3
18.73.7 400 mm dia Ductile Iron Double Flanged metre 13073.3
18.73.8 450 mm dia Ductile Iron Double Flanged metre 15892
18.73.9 500 mm dia Ductile Iron Double Flanged metre 18595.7
18.73.10 600 mm dia Ductile Iron Double Flanged metre 25407
18.74
Providing and fixing unplasticised P.V.C. connection pipe with PTMT
Nuts, collar and bush of approved quality and colour.

18.74.1 15 mm nominal bore with 30cm length each 64.30

18.74.2 15 mm nominal bore with 45 cm length each 76.80
18.75 Providing and fixing PTMT extension nipple for water tank pipe, fittings
of approved quality and colour.
18.75.1 15 mm nominal bore, weighing not less than 32 gms each 46.10
18.75.2 20mm nominal bore, weighing not less than 40 gms each 53.30
18.75.3 25mm nominal bore, weighing not less than 62 gms each 76.60
18.76 Cutting holes up to 30x30 cm in walls including making good the
same:
18.76.1 With common burnt clay F.P.S. (non modular) bricks each 158.10

BCD/SOR_8th Edition_October 2016 189

Code Unit Rate Rs.
Description
No.
18.77 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing each 138.50
drain pipe etc. and repairing the hole after insertion of drain pipe etc.
with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size), including finishing complete so as to
make it leak proof.
18.78 metre 57.70
Making chases up to 7.5x7.5 cm in walls including making good and
finishing with matching surface after housing G.I. pipe etc.
18.79 Making hole up to 20x20 cm and embedding pipes up to 150 mm metre 95.20
diameter in masonry and filling with cement concrete 1:3:6 (1 cement :
3 coarse sand 6 graded stone aggregate 20 mm nominal size) including
disposal of malba.
18.80 Disinfecting C.I. water mains by flushing with water containing
bleaching powder @ 0.5 gms per litre of water and cleaning the same
with fresh water, operation to be repeated three times including getting
the sample of water from the disinfected main tested in the municipal
laboratory.
18.80.1 80 mm diameter C.I. pipe 100 metre 463.60
18.80.2 100 mm diameter C.I. pipe 100 metre 612.60
18.80.3 125 mm diameter C.I. pipe 100 metre 770.70
18.80.4 150 mm diameter C.I. pipe 100 metre 933.00
18.80.5 200 mm diameter C.I. pipe 100 metre 1260.10
18.80.6 250 mm diameter C.I. pipe 100 metre 1605.00
18.80.7 300 mm diameter C.I. pipe 100 metre 1814.80
18.80.8 350 mm diameter C.I. pipe 100 metre 2036.90
18.80.9 400 mm diameter C.I. pipe 100 metre 2278.10
18.80.10 450 mm diameter C.I. pipe 100 metre 2526.90
18.80.11 500 mm diameter C.I. pipe 100 metre 2794.00
18.80.12 600 mm diameter C.I. pipe 100 metre 3351.20
18.81 Extra for every operation of disinfecting the C.I. main by flushing with
water containing bleaching powder @ 0.5 gms per litre of water and
cleaning the same with fresh water, including getting the samples of
water tested in the municipal laboratory :
18.81.1 80 mm diameter C.I. pipe 100 metre 170.50
18.81.2 100 mm diameter C.I. pipe 100 metre 208.50
18.81.3 125 mm diameter C.I. pipe 100 metre 256.60
18.81.4 150 mm diameter C.I. pipe 100 metre 302.50
18.81.5 200 mm diameter C.I. pipe 100 metre 464.60
18.81.6 250 mm diameter C.I. pipe 100 metre 540.70
18.81.7 300 mm diameter C.I. pipe 100 metre 616.00
18.81.8 350 mm diameter C.I. pipe 100 metre 730.70
18.81.9 400 mm diameter C.I. pipe 100 metre 848.00
18.81.10 450 mm diameter C.I. pipe 100 metre 971.50
18.81.11 500 mm diameter C.I. pipe 100 metre 1096.90
18.81.12 600 mm diameter C.I. pipe 100 metre 1357.40

190 BCD/SOR_8th Edition_October 2016

 Code Unit Rate Rs.
Description
No.
18.82 Dismantling old C.I. pipes including excavation and refilling trenches
after taking out the pipes, breaking lead caulked joints, melting of lead
and making into blocks, including stacking of pipes at site lead up to
50 metre :
18.82.1 80 mm diameter C.I. pipe metre 160.20
18.82.2 100 mm diameter C.I. pipe metre 164.40
18.82.3 125 mm diameter C.I. pipe metre 168.40
18.82.4 150 mm diameter C.I. pipe metre 172.50
18.82.5 200 mm diameter C.I. pipe metre 189.70
18.82.6 250 mm diameter C.I. pipe metre 206.50
18.82.7 300 mm diameter C.I. pipe metre 220.60
18.82.8 350 mm diameter C.I. pipe metre 233.10
18.82.9 400 mm diameter C.I. pipe metre 244.30
18.82.10 450 mm diameter C.I. pipe metre 255.80
18.82.11 500 mm diameter C.I. pipe metre 265.20
18.82.12 600 mm diameter C.I. pipe metre 280.00
18.83 Labour for cutting C.I. pipe with steel saw.
18.83.1 80 mm diameter C.I. pipe Each cut 38.20
18.83.2 100 mm diameter C.I. pipe Each cut 51.50
18.83.3 125 mm diameter C.I. pipe Each cut 72.20
18.83.4 150 mm diameter C.I. pipe Each cut 97.10
18.83.5 200 mm diameter C.I. pipe Each cut 129.50
18.83.6 250 mm diameter C.I. pipe Each cut 160.10
18.83.7 300 mm diameter C.I. pipe Each cut 192.50
18.83.8 350 mm diameter C.I. pipe Each cut 223.10
18.83.9 400 mm diameter C.I. pipe Each cut 255.20
18.83.10 450 mm diameter C.I. pipe Each cut 286.10
18.83.11 500 mm diameter C.I. pipe Each cut 318.20
18.83.12 600 mm diameter C.I. pipe Each cut 377.50
18.84 Providing & fixing chrome plated brass battery based infrared sensor
operated pillar cock, having foam flow technology.
18.84.1 15 mm nominal bore each 7123.60
18.85 Providing and fixing Stainless Steel pipe and fitting of grade AISI 304
as per JIS standard 3448 complete with press type fitting (fitting shall
be paid for separately) i/c fixing of the pipe with clamps at 1.00 m
spacing including cutting and making good the walls including testing
of joints complete as per direction of Engineer -in-charge.
(The pipe length inserted in the fitting shall not be measured for
payment) Inernal work - Exposed on wall
18.85.1 15.88 mmouter diapipe metre 229.30
18.85.2 22.22 mm outer dia Pipe metre 370.40
18.85.3 28.58 mm outer dia Pipe metre 468.10
18.85.4 34.00 mm outer dia Pipe metre 647.00
18.85.5 42.70 mm outer dia Pipe metre 793.40
18.85.6 48.60 mm outer dia Pipe metre 919.00

BCD/SOR_8th Edition_October 2016 191

Code Unit Rate Rs.
Description
No.
18.86
Providing and fixing Stainless Steel pipe and fitting of grade AISI 304 as per
JIS standard 3448 complete with press type fitting (fitting shall be paid for
separately) i/c fixing of the pipe with clamps at 1.00m spacing and also
including cutting of chases and making good the walls including testing of
joints complete as per direction of Engineer -in-charge. (The pipe length
inserted in the fitting shall not be measured for payment)
Internal work - Concealed Pipe

18.86.1 15.88 mm outer dia .Pipes. metre 288.50

18.86.2 22.22 mm Outer dia pipes metre 429.50
18.87 Providing and fixing required Stainless Steel Fitting of press fit design of
grade AISI 304 conforming to JWWA G116 standard with V-profile or M-
profile and with O-ring sealing gasket of EPDM material of required dia as
per dirction of Engineer-in-charge.
Coupling/Socket
18.87.1 For 15.88 mm outer dia pipe each 69.60
18.87.2 For 22.22 mm outer dia pipe each 107.40
18.87.3 For 28.58 mm outer dia pipe each 131.80
18.87.4 For 34.00 mm outer dia pipe each 282.00
18.87.5 For 42.70 mm outer dia pipe each 406.80
18.87.6 For 48.60 mm outer dia pipe each 544.40
18.88 Providing and fixing required Stainless Steel Fitting of press fit design of
grade AISI 304 conforming to JWWA G116 standard with V-profile or M-
profile and with O-ring sealing gasket of EPDM material of Providing and
fixing required Stainless Steel Fitting of press fit design of grade AISI 304
conforming to JWWA G116 standard with V-profile or M-profile and with O-
ring sealing gasket of EPDM material of required dia as per dirction of
Engineer-in-charge.
Reducer
18.88.1 For 22.22 mm x 15.88 mm outer dia pipe each 125.70
18.88.2 For 28.58 mm x 15.88 mm outer dia pipe each 172.10
18.88.3 For 28.58 mm x 22.22 mm outer dia pipe each 177.00
18.88.4 For 34.00 mm x 15.88 mm outer dia pipe each 266.10
18.88.5 For 34.00 mm x 22.22 mm outer dia pipe each 289.30
18.88.6 For 34.00 mm x 28.58 mm outer dia pipe each 289.30
18.88.7 For 42.70 mm x 15.88 mm outer dia pipe each 438.20
18.88.8 For 42.70 mm x 22.22 mm outer dia pipe each 441.90
18.88.9 For 42.70 mm x 28.58 mm outer dia pipe each 441.90
18.88.10 For 42.70 mm x 34.00 mm outer dia pipe each 472.40
18.88.11 For 48.60 mm x 15.88 mm outer dia pipe each 571.30
18.88.12 For 48.60 mm x 22.22 mm outer dia pipe each 573.70
18.88.13 For 48.60 mm x 28.58 mm outer dia pipe each 578.60
18.88.14 For 48.60 mm x 34.0 mm outer dia pipe each 584.70
18.88.15 For 48.60 mm x42.70 mm outer dia pipe each 637.20

192 BCD/SOR_8th Edition_October 2016

 Code Unit Rate Rs.
Description
No.
18.89 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Slip Coupling/ Socket
18.89.1 For 15.88 mm outer dia pipe each 137.90
18.89.2 For 22.22 mm outer dia pipe each 224.60
18.89.3 For 28.58 mm outer dia pipe each 288.10
18.89.4 For 34.00 mm outer dia pipe each 426.00
18.89.5 For 42.70 mm outer dia pipe each 598.10
18.89.6 For 48.60 mm outer dia pipe each 743.40
18.90 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Elbow 90o
18.90.1 For 15.88mm outer dia pipe each 105.00
18.90.2 For 22.22 mm outer dia pipe each 186.80
18.90.3 For 28.58 mm outer dia pipe each 257.60
18.90.4 For 34.00 mm outer dia pipe each 523.70
18.90.5 For 42.70 mm outer dia pipe each 802.00
18.90.6 For 48.60 mm outer dia pipe each 986.30
18.91 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Reducing Elbow 90o
18.91.1 For22.22 mm x 15.88 mm outer dia pipe each 180.70
18.91.2 For 28.58 mm x 15.88 mm outer dia pipe each 263.70
18.91.3 For 28.58 mm x 22.22 mm outer dia pipe each 269.80
18.91.4 For 34.00 mm x 22.22 mm outer dia pipe each 391.80
18.91.5 For 34.00 mm x 28.58 mm outer dia pipe each 483.40
18.91.6 For 42.70 mm x 34.00 mm outer dia pipe each 852.00
18.92 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Equal Tee
18.92.1 For 15.88 mm outer dia pipe each 194.10
18.92.2 For 22.22 mm outer dia pipe each 282.00
18.92.3 For 28.58 mm outer dia pipe each 361.30
18.92.4 Details of Cost for one no. each 753.20
18.92.5 For 42.70 mm outer dia pipe each 1054.70
18.92.6 For 48.60 mm outer dia pipe each 1254.90

BCD/SOR_8th Edition_October 2016 193

Code Unit Rate Rs.
Description
No.
18.93 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Reducing Tee
18.93.1 For 22.22 mm x 15.88 mm outer dia pipe each 274.60
18.93.2 For 28.58 mm x 15.88 mm outer dia pipe each 341.80
18.93.3 For 28.58 mm x 22.22 mm outer dia pipe each 355.20
18.93.4 For 34.00 mm x 15.88 mm outer dia pipe each 668.90
18.93.5 For 34.00 mm x 22.22 mm outer dia pipe each 681.20
18.93.6 For 34.00 mm x 28.58 mm outer dia pipe each 688.50
18.93.7 For 42.70 mm x 15.88 mm outer dia pipe each 999.80
18.93.8 For 42.70 mm x 22.22 mm outer dia pipe each 1002.20
18.93.9 For 42.70 mm x 28.58 mm outer dia pipe each 1003.40
18.93.10 For 42.70 mm x 34.00 mm outer dia pipe each 1013.20
18.93.11 For 48.60 mm x 15.88 mm outer dia pipe each 1091.30
18.93.12 For 48.60 mm x 22.22 mm outer dia pipe each 1114.50
18.93.13 For 48.60 mm x 28.58 mm outer dia pipe each 1123.00
18.93.14 For 48.60 mm x 34.00 mm outer dia pipe each 1169.40
18.93.15 For 48.60 mm x 42.70 mm outer dia pipe each 1212.20
18.94 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Male Thread Tee
18.94.1 For 15.88 mm outer dia x 15 mm nominal dia threaded each 349.10
18.94.2 For 22.22 mm outer dia x 15 mm nominal dia threaded each 419.90
18.94.3 For 22.22 mm outer dia x 20 mm nominal dia threaded each 449.20
18.94.4 For 28.58 mm outer dia x 15 mm nominal dia threaded each 505.40
18.94.5 For 28.58 mm outer dia x 20 mm nominal dia threaded each 527.40
18.94.6 For 28.58 mm outer dia x 25 mm nominal dia threaded each 589.60
18.94.7 For 34.00 mm outer dia x 15 mm nominal dia threaded each 734.90
18.94.8 For 34.00 mm outer dia x 20 mm nominal dia threaded each 794.70
18.94.9 For 34.00 mm outer dia x 25 mm nominal dia threaded each 948.50
18.94.10 For 34.00 mm outer dia x 32 mm nominal dia threaded each 1197.50
18.94.11 For 42.70 mm outer dia x 15 mm nominal dia threaded each 1121.80
18.94.12 For 42.70 mm outer dia x 20 mm nominal dia threaded each 1148.70
18.94.13 For 42.70 mm outer dia x 25 mm nominal dia threaded each 1250.00
18.94.14 For 42.70 mm outer dia x 32 mm nominal dia threaded each 1387.90
18.94.15 For 42.70 mm outer dia x 40 mm nominal dia threaded each 1685.80
18.94.16 For 48.60 mm outer dia x 15 mm nominal dia threaded each 1220.70
18.94.17 For 48.60 mm outer dia x 20 mm nominal dia threaded each 1257.30
18.94.18 For 48.60 mm outer dia x 25 mm nominal dia threaded each 1311.00
18.94.19 For 48.60 mm outer dia x 32 mm nominal dia threaded each 1574.70
18.94.20 For 48.60 mm outer dia x 40 mm nominal dia threaded each 1746.80
18.94.21 For 48.60 mm outer dia x 50 mm nominal dia threaded each 2135.00

194 BCD/SOR_8th Edition_October 2016

 Code Unit Rate Rs.
Description
No.
18.95 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Female Thread Tee
18.95.1 For 15.88 mm outer dia x15 mm nominal dia threaded each 356.50
18.95.2 For 22.22 mm outer dia x 15 mm nominal dia threaded each 419.90
18.95.3 For 22.22 mm outer dia x 20 mm nominal dia threaded each 434.60
18.95.4 For 28.58 mm outer dia x 15 mm nominal dia threaded each 543.20
18.95.5 For 28.58 mm outer dia x 20 mm nominal dia threaded each 555.40
18.95.6 For 28.58 mm outer dia x 25 mm nominal dia threaded each 607.90
18.95.7 For 34.00 mm outer dia x 15 mm nominal dia threaded each 815.40
18.95.8 For 34.00 mm outer dia x 20 mm nominal dia threaded each 828.90
18.95.9 For 34.00 mm outer dia x 25 mm nominal dia threaded each 935.10
18.95.10 For 34.00 mm outer dia x 32 mm nominal dia threaded each 1110.80
18.95.11 For 42.70 mm outer dia x 15 mm nominal dia threaded each 1091.30
18.95.12 For 42.70 mm outer dia x 20 mm nominal dia threaded each 1110.80
18.95.13 For 42.70 mm outer dia x 25 mm nominal dia threaded each 1247.50
18.95.14 For 42.70 mm outer dia x 32 mm nominal dia threaded each 1302.50
18.95.15 For 42.70 mm outer dia x 40 mm nominal dia threaded each 1418.40
18.95.16 For 48.60 mm outer dia x 15 mm nominal dia threaded each 1300.00
18.95.17 For 48.60 mm outer dia x 20 mm nominal dia threaded each 1313.50
18.95.18 For 48.60 mm outer dia x 25 mm nominal dia threaded each 1361.10
18.95.19 For 48.60 mm outer dia x 32 mm nominal dia threaded each 1445.30
18.95.20 For 48.60 mm outer dia x 40 mm nominal dia threaded each 1505.10
18.95.21 For 48.60 mm outer dia x 50 mm nominal dia threaded each 1505.10
18.96 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Female Thread Connector/ Adapter
18.96.1 For 15.88 mm outer dia x 15 mm nominal dia threaded each 231.90
18.96.2 For 22.22 mm outer dia x 15 mmnominal dia threaded each 280.80
18.96.3 For 22.22 mm outer dia x 20 mm nominal dia threaded each 289.30
18.96.4 For 28.58 mm outer dia x 15 mm nominal dia threaded each 338.10
18.96.5 For 28.58 mm outer dia x 20 mm nominal dia threaded each 349.10
18.96.6 For 28.58 mm outer dia x 25 mm nominal dia threaded each 411.40
18.96.7 For 34.00 mm outer dia x 25 mm nominal dia threaded each 499.30
18.96.8 For 34.00 mm outer dia x 32 mm nominal dia threaded each 656.70
18.96.9 For 42.70 mm outer dia x 32 mm nominal dia threaded each 703.10
18.96.10 For 42.70 mm outer dia x 40 mm nominal dia threaded each 831.30
18.96.11 For 48.60 mm outer dia x 40 mm nominal dia threaded each 1022.90
18.96.12 For 48.60 mm outer dia x 50 mm nominal dia threaded each 1022.90

BCD/SOR_8th Edition_October 2016 195

Code Unit Rate Rs.
Description
No.
18.97 Providing and fixing required Stainless Steel Fitting of press fit design
of grade
Male AISIConnector/
Thread 304 conforming to JWWA G116 standard with V-profile or
Adapter
18.97.1 For 15.88 mm outer dia x 15 mm nominal dia threaded each 235.60
18.97.2 For 22.22 mm outer dia x 15 mm nominal dia threaded each 277.10
18.97.3 For 22.22 mm outer dia x 20 mm nominal dia threaded each 302.70
18.97.4 For 28.58 mm outer dia x 20 mm nominal dia threaded each 382.10
18.97.5 For 28.58 mm outer dia x 25 mm nominal dia threaded each 390.60
18.97.6 For 34.00 mm outer dia x 25 mm nominal dia threaded each 562.70
18.97.7 For 34.00 mm outer dia x 32 mm nominal dia threaded each 689.70
18.97.8 For 42.70 mm outer dia x 32 mm nominal dia threaded each 792.20
18.97.9 For 42.70 mm outer dia x 40 mm nominal dia threaded each 886.20
18.97.10 For 48.60 mm outer dia x 40 mm nominal dia threaded each 1025.40
18.97.11 For 48.60 mm outer dia x 50 mm nominal dia threaded each 1389.20
18.98 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Valve Connector
18.98.1 For 15.88 mm outer dia x 15 mm nominal dia threaded each 285.70
18.98.2 For 22.22 mm outer dia x 15 mm nominal dia threaded each 336.90
18.98.3 For 22.22 mm outer dia x 20 mm nominal dia threaded each 360.10
18.98.4 For 28.58 mm outer dia x 25 mm nominal dia threaded each 517.60
18.98.5 For 34.00 mm outer dia x 32 mm nominal dia threaded each 767.80
18.98.6 For 42.70 mm outer dia x 40 mm nominal dia threaded each 1068.10
18.98.7 For 48.60 mm outer dia x 50 mm nominal dia threaded each 1435.50
18.99 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Female Threaded Elbow 90O
18.99.1 For 15.88 mm outer dia x 15 mm nominal dia threaded each 250.20
18.99.2 For 22.22 mm outer dia x 15 mm nominal dia threaded each 335.70
18.99.3 For 22.22 mm outer dia x 20 mm nominal dia threaded each 346.70
18.99.4 For 25.58 mm outer dia x 25 mm nominal dia threaded each 513.90
18.99.5 For 34.00 mm outer dia x 32 mm nominal dia threaded each 894.80
18.99.6 For 42.70 mm outer dia x 32 mm nominal dia threaded each 1123.00
18.99.7 For 42.70 mm outer dia x 40 mm nominal dia threaded each 1253.00
18.99.8 For 48.60 mm outer dia x 40 mm nominal dia threaded each 1346.40
18.99.9 For 48.60 mm outer dia x 50 mm nominal dia threaded each 1569.80

196 BCD/SOR_8th Edition_October 2016

 Code Unit Rate Rs.
Description
No.
18.100 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Male Threaded Elbow 90O
18.100.1 For 15.88 mm outer dia x 15 mm nominal dia threaded each 263.70
18.100.2 For 22.22 mm outer dia x 15 mm nominal dia threaded each 333.20
18.100.3 For 22.22 mm outer dia x 20 mm nominal dia threaded each 351.60
18.100.4 For 28.58 mm outer dia x 25 mm nominal dia threaded each 460.20
18.100.5 For 34.00 mm outer dia x 25 mm nominal dia threaded each 738.50
18.100.6 For 34.00 mm outer dia x 32 mm nominal dia threaded each 898.40
18.100.7 For 42.70 mm outer dia x 32 mm nominal dia threaded each 1140.10
18.100.8 For 42.70 mm outer dia x 40 mm nominal dia threaded each 1293.90
18.100.9 For 48.60 mm outer dia x 40 mm nominal dia threaded each 1452.60
18.100.10 For 48.60 mm outer dia x 50 mm nominal dia threaded each 1768.80
18.101 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Cap
18.101.1 For 15.88 mm outer dia pipe each 54.90
18.101.2 For 22.22 mm outer dia pipe each 78.10
18.101.3 For 28.58 mm outer dia pipe each 102.50
18.101.4 For 34.00 mm outer dia pipe each 211.20
18.101.5 For 42.70 mm outer dia pipe each 308.80
18.101.6 For 48.60 mm outer dia pipe each 402.80
18.102 Providing and fixing required Stainless Steel Fitting of press fit design
of grade AISI 304 conforming to JWWA G116 standard with V-profile or
M-profile and with O-ring sealing gasket of EPDM material of required
dia as per dirction of Engineer-in-charge.
Pipe Bridge
18.102.1 For 15.88 mm outer dia pipe each 261.20
18.102.2 For 22.22 mm outer dia pipe each 330.80
18.102.3 For 28.58 mm outer dia pipe each 496.80

BCD/SOR_8th Edition_October 2016 197

SUB HEAD : 19.0
DRAINAGE
 BUILDING WORK - Contd.

19.0 Drainage
Code
Description Unit Rate Rs.
No.
NOTE : - The rates given for all the items under sub-head ' Drainage'
are applicable to work executed in soils above sub- soil water level.
Extra allowance has to be made for work under sub- soil water level.

STONE WARE PIPES AND FITTINGS

19.1 Providing, laying and jointing glazed stoneware pipes class SP-1
with stiff mixture of cement mortar in the proportion of 1:1 (1
cement : 1 fine sand) including testing of joints etc. complete :

19.1.1 100 mm diameter metre 181.20

19.1.2 150 mm diameter metre 281.90
19.1.3 200 mm diameter metre 424.60
19.1.5 250 mm diameter metre 660.30
19.1.6 300 mm diameter metre 730.60
19.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse
sand : 10 graded stone aggregate 40 mm nominal size) all-round
S.W. pipes including bed concrete as per standard design :

19.2.1 100 mm diameter S.W. pipe metre 352.70

19.2.2 150 mm diameter S.W. pipe metre 431.30
19.2.3 200 mm diameter S.W. pipe metre 502.80
19.2.4 250 mm diameter S.W. pipe metre 581.40
19.3 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse
sand : 10 graded stone aggregate 40 mm nominal size) up to
haunches of S.W. pipes including bed concrete as per standard
design :
19.3.1 100 mm diameter S.W. pipe metre 167.60
19.3.2 150 mm diameter S.W. pipe metre 271.60
19.3.3 200 mm diameter S.W. pipe metre 319.30
19.3.4 250 mm diameter S.W. pipe metre 371.70
19.3.5 300 mm diameter S.W. pipe metre 428.90
19.4 Providing and fixing square-mouth S.W. gully trap class SP-1
complete with C.I. grating brick masonry chamber with water
tight C.I. cover with frame of 300 x300 mm size (inside) the weight
of cover to be not less than 4.50 kg and frame to be not less than
2.70 kg as per standard design :
19.4.1 100x100 mm size P type
19.4.1.1 With common burnt clay F.P.S. (non modular) bricks of each 1415.00
class designation 7.5
19.4.1.2 With Sewer bricks conforming to IS : 4885 each 1442.50
19.4.2 150 x 100 mm size P type
19.4.2.1 With common burnt clay F.P.S. (non modular) bricks of each 1453.80
class designation 7.5
19.4.2.2 With sewer bricks conforming to IS : 4885 each 1481.30
19.4.3 180x150 mm size P type
19.4.3.1 With common burnt clay F.P.S. (non modular) bricks of each 1553.60
class designation 7.5
19.4.3.2 With Sewer bricks conforming to IS : 4885 each 1581.10

198 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
19.5 Dismantling of old S.W. pipes including breaking of joints and
bed concrete stacking of useful materials near the site within 50
m lead and disposal of unserviceable materials into municipal
dumps :
19.5.1 100 mm diameter metre 21.00
19.5.2 150 mm diameter metre 23.30
19.5.3 200 mm diameter metre 24.90
19.5.4 250 mm diameter metre 26.40
19.5.5 300 mm diameter metre 28.00
19.5.6 350 mm diameter metre 32.10
19.5.7 400 mm diameter metre 35.10
19.5.8 450 mm diameter metre 36.70
19.6 Providing and laying non-pressure NP2 class (light duty) R.C.C.
pipes with collars jointed with stiff mixture of cement mortar in
the proportion of 1:2 (1 cement : 2 fine sand) including testing of
joints etc. complete :
19.6.1 100 mm dia. R.C.C. pipe metre 305.50
19.6.2 150 mm dia. R.C.C. pipe metre 329.40
19.6.3 250 mm dia. R.C.C. pipe metre 430.40
19.6.4 300 mm dia. R.C.C. pipe metre 471.10
19.6.5 450 mm dia. R.C.C. pipe metre 646.40
19.6.6 500 mm dia. R.C.C. pipe metre 881.60
19.6.7 600 mm dia. R.C.C. pipe metre 1325.10
19.6.8 700 mm dia. R.C.C. pipe metre 1507.20
19.6.9 800 mm dia. R.C.C. pipe metre 1693.90
19.6.10 900 mm dia. R.C.C. pipe metre 1876.80
19.6.11 1000 mm dia. R.C.C. pipe metre 2320.60
19.6.12 1100 mm dia. R.C.C. pipe metre 2739.80
19.6.13 1200 mm dia. R.C.C. pipe metre 2897.00
19.7 Constructing brick masonry manhole in cement mortar 1:4 ( 1
cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1
cement : 2 coarse sand : 4 graded stone aggregate 20 mm
nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse
sand : 8 graded stone aggregate 40 mm nominal size), inside
plastering 12 mm thick with cement mortar 1:3 (1 cement : 3
coarse sand) finished with floating coat of neat cement and
making channels in cement concrete 1:2:4 (1 cement : 2 coarse
sand : 4 graded stone aggregate 20 mm nominal size) finished
with a floating coat of neat cement complete as per standard
19.7.1 Inside size 90x80 cm and 45 cm deep including C.I. cover
with frame (light duty) 455x610 mm internal dimensions,
total weight of cover and frame to be not less than 38 kg
(weight of cover 23 kg and weight of frame 15 kg) :
19.7.1.1 With common burnt clay F.P.S. (non modular) bricks of each 6958.90
class designation 7.5
19.7.1.2 With Sewer bricks conforming to IS : 4885 each 7031.00
19.7.2 Inside size 120x90 cm and 90 cm deep including C.I. cover
with frame (medium duty) 500 mm internal diameter, total
weight of cover and frame to be not less than 116 kg (weight
of cover 58 kg and weight of frame 58 kg) :
19.7.2.1 With common burnt clay F.P.S. (non modular) bricks of each 15986.50
class designation 7.5
BCD/SOR_8th Edition_October 2016 199
Code
Description Unit Rate Rs.
No.
19.7 19.7.2.2 With Sewer bricks conforming to IS : 4885 each 16183.60
19.7.3 Inside size 120x90 cm and 90 cm deep including C.I. cover
with frame (heavy duty) 560 mm internal diameter, total
weight of cover and frame to be not less than 208 kg
(weight of cover 108 kg and weight of frame 100 kg) :
19.7.3.1 With common burnt clay F.P.S. (non modular) bricks of each 20772.20
class designation 7.5
19.7.3.2 With Sewer bricks conforming to IS : 4885 each 20941.80
19.8 Extra for depth for manholes :
19.8.1 Size 90x80 cm
19.8.1.1 With common burnt clay F.P.S. (non modular) bricks of metre 5217.80
class designation 7.5
19.8.1.2 With Sewer bricks conforming to IS : 4885 metre 5427.60
19.8.2 Size 120x90 cm
19.8.2.1 With common burnt clay F.P.S. (non modular) bricks of metre 6242.60
class designation 7.5
19.8.2.2 With Sewer bricks conforming to IS : 4885 metre 6492.70
19.9 Constructing brick masonry circular type manhole 0.91 m internal
dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement
:4 coarse sand), in side cement plaster 12 mm thick with cement
mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat
of neat cement, foundation concrete 1:3:6 mix (1 cement : 3
coarse sand : 6 graded stone aggregate 40 mm nominal size),
and making necessary channel in cement concrete 1:2:4 (1
cement : 2 coarse sand : 4 graded stone aggregate 20 mm
nominal size) finished with a floating coat of neat cement, all
complete as per standard design :
19.9.1 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-
20 grade designation) 560 mm internal diameter conforming
to I.S. 12592, total weight of cover and frame to be not less
than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20 mm nominal
size) including centering, shuttering all complete.
(Excavation, foot rests and 12mm thick cement plaster at the
external surface shall be paid for separately) :
19.9.1.1 With common burnt clay F.P.S. (non modular) bricks of each 7136.80
class designation 7.5
19.9.1.2 With Sewer bricks conforming to IS : 4885 each 7204.60
19.10 Extra depth for circular type manhole 0.91m internal dia (at
bottom)
beyond 0.91 m to 1.67 m
19.10.1 With common burnt clay F.P.S. (non modular) bricks of metre 4630.09
class designation 7.5
19.10.2 With Sewer bricks conforming IS : 4885 metre 4630.09

200 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
19.11 bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4
coarse sand) inside cement plaster 12 mm thick with cement
mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat
of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse
sand : 6 graded stone aggregate 40 mm nominal size) and
making necessary channel in cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20 mm nominal size)
finished with a floating coat of neat cement, all complete as per
standard design :
19.11.1 1.68 m deep with SFRC Cover and frame (heavy duty HD-20
grade designation) 560 mm internal diameter conforming to
I.S. 12592, total weight of cover and frame to be not less
than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20 mm nominal
size) including centering, shuttering all complete.
(Excavation, foot rests and 12 mm thick cement plaster at
the external surface shall be paid for separately) :

19.11.1.1 With common burnt clay F.P.S. (non modular) bricks of each 13391.90
class designation 7.5
19.11.1.2 With Sewer bricks conforming IS : 4885 each 14198.20
19.12 Extra depth for circular type manhole 1.22 m internal dia (at
bottom)beyond 1.68 m to 2.29 m :
19.12.1 With common burnt clay F.P.S. (non modular) bricks of metre 5778.90
class designation 7.5
19.12.2 With Sewer bricks conforming IS : 4885 metre 6008.20
19.13 Constructing brick masonry circular manhole 1.52 m internal dia
at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4
coarse sand) inside cement plaster 12 mm thick with cement
mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat
of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse
sand : 6 graded stone aggregate 40 mm nominal size) and
making necessary channel in cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20 mm nominal size)
finished with a floating
coat of neat cement, all complete as per standard design :
19.13.1 2.30 m deep with SFRC Cover and frame (heavy duty HD-
20 grade designation) 560 mm internal diameter
conforming to I.S. 12592, total weight of cover and
frame to be not less than 182 kg. fixed in cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size) including
centering, shuttering all complete.
(Excavation, foot rests and 12 mm thick cement plaster
at the external surface shall be paid for separately) :
19.13.1.1 With common burnt clay F.P.S. (non modular) bricks of each 29182.50
class designation 100A
19.13.1.2 With Sewer bricks conforming IS : 4885 each 29873.30

BCD/SOR_8th Edition_October 2016 201

Code
Description Unit Rate Rs.
No.
19.14 Extra depth for circular type manhole 1.52 m internal dia (at
bottom) beyond 2.30 m :
19.14.1 With common burnt clay F.P.S. (non modular) bricks of metre 13978.60
class designation 100A
19.14.2 With Sewer bricks conforming IS : 4885 metre 14571.60
19.15 Providing M.S. foot rests including fixing in manholes with
20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse
sand : 6 graded stone aggregate 20 mm nominal size) as per
standard design :
19.15.1 With 20x20 mm square bar each 208.00
19.15.2 With 20 mm diameter round bar each 173.30
19.16 Providing orange colour safety foot rest of minimum 6 mm thick each 208.00
plastic encapsulated as per IS : 10910, on 12 mm dia steel bar
conforming to IS : 1786, having minimum cross section as 23
mmx25 mm and over all minimum length 263 mm and width as
165 mm with minimum 112 mm space between protruded legs
having 2 mm tread on top surface by ribbing or chequering
besides necessary and adequate anchoring projections on tail
length on 138 mm as per standard drawing and suitable to with
stand the bend test and chemical resistance test as per
specifications and having manufacture's permanent identification
mark to be isible even after fixing, including fixing in manholes
with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3
coarse sand : 6 graded stone aggregate 20 mm nominal size)
complete as per design.
19.17 Replacement of M.S. foot rests in manholes including
dismantling concrete blocks and fixing with 20x20x10 cm cement
concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone
aggregate 20 mm nominal size) :
19.17.1 With 20x20 mm square bar each 238.70
19.17.2 With 20 mm diameter round bar each 204.00
19.18 Supplying and fixing C.I. cover without frame for manholes :
19.18.1 455x610 mm rectangular C.I. cover (light duty) the weight of each 1264.50
the cover to be not less than 23 kg
19.18.2 500 mm diameter C.I. cover (medium duty) the weight of the each 2864.40
cover to be not less than 58 kg
19.18.3 560 mm diameter C.I. cover (heavy duty) the weight of the each 6165.80
cover to be not less than 108 kg
19.19 Providing and fixing in position pre-cast R.C.C. manhole cover
and frame of required shape and approved quality
19.19.1 L D- 2.5
19.19.1.1 Rectangular shape 600x450 mm internal dimensions each 1111.40
19.19.1.2 Square shape 450 mm internal dimensions each 950.80
19.19.1.3 Circular shape 450 mm internal diameter each 889.80
19.19.2 M D - 10
19.19.2.1 Square shape 450 mm internal dimension each 1056.80
19.19.2.2 Circular shape 500 mm internal diameter each 969.50
19.19.3 H D - 20
19.19.3.1 Circular shape 560 mm internal diameter each 1528.10
19.19.4 EHD - 35
19.19.4.1 Circular shape 560 mm internal dia each 1680.70

202 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
19.20 Supplying and fixing C.I. cover 300x300 mm without frame for each 287.50
gully trap (standard pattern) the weight of cover to be not less
than 4.5 kg
19.21 Making connection of drain or sewer line with existing manhole
including breaking into and making good the walls, floors with
cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size) cement plastered on both
sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished
with a floating coat of neat cement and making necessary
channels for the drain etc. complete :
19.21.1 For pipes 100 to 250 mm diameter each 254.60
19.21.2 For pipes 250 to 300 mm diameter each 305.30
19.21.3 For pipes 350 to 450 mm diameter each 445.30
19.22 Providing sand cast iron drop connection externally for 60 cm
drop from branch sewer line to main sewer manhole including
inspection and cleaning eye with chain and lid, sand cast iron
drop pipe and bend encased all-round with cement concrete
1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm
nominal size) with all centering and shuttering required, cutting
holes in walls and making good with brick work in cement mortar
1:4 (1 cement : 4 coarse sand)plastered with cement mortar 1:3 (1
cement : 3 coarse sand) on inside of the manhole wall, lead
caulked joints between sand cast iron pipes and fittings, stiff
cement mortar 1:1 (1 cement : 1 fine sand) joints between sand
cast iron tee and S.W. pipe, making required channels
complete as per standard design and specifications :
19.22.1 100 mm dia sand cast iron drop connection each 4760.00
19.22.2 150 mm dia sand cast iron drop connection each 6364.70
19.23 Extra for depths beyond 60 cm of sand cast iron drop connection
complete :
19.23.1 For 100 mm dia sand cast iron drop connection metre 1579.00
19.23.2 For 150 mm dia sand cast iron drop connection metre 2131.10
19.24 Dismantling of manhole including R.C.C. top slab, C.I. cover with
frame, including stacking of useful materials near the site and
disposal of unserviceable materials into municipal dumps within
50 m lead :
19.24.1 Rectangular manhole 90x80 cm and 45 cm deep each 684.30
19.24.2 Rectangular manhole 120x90 cm and 90 cm deep each 1212.00
19.24.3 Rectangular arch type manhole 140x90 cm and 2.45 m deep each 2035.60
19.24.4 Circular manhole 122 cm diameter and 1.68 m deep each 1559.80
19.25 Extra for depth of manholes dismantled :
19.25.1 Rectangular manhole 90x80 cm and beyond 45 cm depth metre 490.10
19.25.2 Rectangular manhole 120x90 cm and beyond 90 cm depth metre 583.50
19.25.3 Rectangular arch type manhole 140x90 cm and beyond 2.45 metre 470.90
m depth (up to 4.25 m depth)
19.25.4 Circular manhole 122 cm diameter and beyond 1.68 m depth metre 531.60
(up to 2.29 m depth)

BCD/SOR_8th Edition_October 2016 203

Code
Description Unit Rate Rs.
No.
19.26 Raising manhole cover and frame slab to required level including
dismantling existing slab and making good the damage as
required (Raising depth of manhole to be paid separately) :
19.26.1 Rectangular manhole 90x80 cm with rectangular cover each 1110.40
600x450 mm of grade LD - 2.5
19.26.2 Rectangular manhole 120x90 cm with circular cover 500 mm each 1738.00
dia of grade MD - 10
19.26.3 Rectangular manhole 120x90 cm with circular cover 560 mm each 1620.70
dia of grade HD - 20
19.26.4 Circular manhole 140 cm dia with circular cover 600 mm dia each 166.60
of grade EHD - 35
19.27 Constructing brick masonry road gully chamber 50x45x60 cm
with bricks in cement mortar 1:4 (1 cement : 4 coarse sand)
including 500x450 mm pre-cast R.C.C. horizontal grating with
frame complete as per standard design :
19.27.1 With common burnt clay F.P.S. (non modular) bricks of each 3384.80
class designation 7.5
19.28 Constructing brick masonry road gully chamber 45x45x77.5 cm
with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with
precast R.C.C. vertical grating complete as per standard design :
19.28.1 With common burnt clay F.P.S. (non modular) bricks of each 3831.50
class designation 7.5
19.29 Constructing brick masonry road gully chamber 110x50x77.5 cm
with bricks in cement mortar 1:4 (1 cement : 4 coarse sand)
including 500x450 mm pre-cast R.C.C. horizontal grating with
frame and vertical
grating complete as per standard design :
19.29.1 With common burnt clay F.P.S. (non modular) bricks of each 6406.60
class designation 7.5
19.30 Constructing brick masonry chamber for underground C.I.
inspection chamber and bends with bricks in cement mortar 1:4 (1
cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610
mm internal dimensions, total weight of cover with frame to be not
less than 38 kg (weight of cover 23 kg and weight of frame 15 kg),
R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1
cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal
size), inside plastering 12 mm thick with cement mortar 1:3 (1
cement : 3 coarse sand), finished smooth with a floating coat of neat
cement on walls and bed concrete etc. complete as per standard
design :
19.30.1 Inside dimensions 455x610 mm and 45 cm deep for single
pipe line :
19.30.1.1 With common burnt clay F.P.S. (non modular) bricks of each 4147.30
class designation 7.5
19.30.2 Inside dimensions 500x700 mm and 45 cm deep for pipe
line with one or two inlets :
19.30.2.1 With common burnt clay F.P.S. (non modular) bricks of each 4685.90
class designation 7.5
19.30.3 Inside dimensions 600x 850 mm and 45 cm deep for pipe
line with three or more inlets :
19.30.3.1 With common burnt clay F.P.S. (non modular) bricks of each 5352.70
class designation 7.5

204 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
19.31 Extra for depth beyond 45 cm of brick masonry chamber :

19.31.1 For 455x610 mm size

19.31.1.1 With common burnt clay F.P.S. (non modular) bricks of metre 3645.80
class designation 7.5
19.31.2 For 500x700 mm size
19.31.2.1 With common burnt clay F.P.S. (non modular) bricks of metre 3972.10
class designation 7.5
19.31.3 For 600x850 mm size
19.31.3.1 With common burnt clay F.P.S. (non modular) bricks of metre 4618.60
class designation 7.5
19.32 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm
dry brick honey comb shaft with bricks and S.W. drain pipe 100
mm diameter, 1.8 m long complete as per standard design.
19.32.1 With common burnt clay F.P.S. (non modular) bricks of each 28775.50
class designation 7.5
19.33 Constructing soak pit 1.20x1.20x1.20 m filled with brickbats each 3248.30
including S.W. drain pipe 100 mm diameter and 1.20 m long
complete as per standard design.
19.34 Providing and fixing S.W. intercepting trap in manholes with stiff
mixture of cement mortar 1:1 (1 cement : 1 fine sand) including
testing of joints etc. complete :
19.34.1 100 mm dia each 281.30
19.34.2 150 mm dia each 380.30
19.35 Providing and laying Non Pressure NP-3 class (Medium duty)
R.C.C. pipes including collars/spigot jointed with stiff mixture of
cement mortar in the proportion of 1:2 (1 cement : 2 fine sand)
including testing of joints etc. complete
19.35.1 450 mm dia RCC pipes. metre 1925.40
19.35.2 600 mm dia RCC pipes. metre 2528.70
19.35.3 900 mm dia RCC pipes. metre 3988.30
19.35.4 1000 mm dia RCC pipes. (Laying by mannual/machenical metre 4923.30
means)
19.35.5 1200 mm dia RCC pipes. (Laying by mannual/ metre 6454.20
machenical means)
19.35.6 1800 mm dia RCC pipes. (Laying by mannual/ metre 11957.10
machenical means)
19.36 Providing and laying Non Pressure NP-4 class (Heavy duty)
R.C.C. pipes including collars/spigot jointed with stiff mixture of
cement mortar in the proportion of 1:2 (1 cement : 2 fine sand)
including testing of joints etc. complete
19.36.1 450 mm dia RCC pipes. metre 2214.70
19.36.2 600 mm dia RCC pipes. metre 2913.20
19.36.3 900 mm dia RCC pipes. metre 5752.20
19.36.4 1000 mm dia RCC pipes.(Laying machenical means) metre 6974.10
19.36.5 1200 mm dia RCC pipes. (Laying machenical means) metre 8248.70
19.36.6 1800 mm dia RCC pipes. (Laying machenical means) metre 17077.30

BCD/SOR_8th Edition_October 2016 205

SUB HEAD : 20.0
PILE WORK
 BUILDING WORK - Contd.

20.0 Pile Work

Code
Description Unit Rate Rs.
No.
20.1 Providing, driving and installing driven cast-in-situ reinforced
cement concrete piles of grade M-25 of specified diameter and
length below the pile cap, to carry safe working load not less
than specified, excluding the cost of steel reinforcement but
including the cost of shoe and the length of pile to be
embedded in the pile cap etc. all complete. (Length of pile for
payment shall be measured from top of shoe to the bottom of
pile cap) :
20.1.1 400 mm dia piles metre 1725.10
20.1.2 450 mm dia piles metre 2106.00
20.1.3 500 mm dia piles metre 2531.60
20.1.4 550 mm dia piles metre 2706.00
20.1.5 750 mm dia piles metre 4503.20
20.1.6 1000 mm dia piles metre 7323.10
20.1.7 1200 mm dia piles metre 9260.10
20.1.8 1500 mm dia piles metre 12758.50
20.2 Boring, providing and installing bored cast-in-situ reinforced
cement concrete piles of grade M-25 of specified diameter and
length below the pile cap, to carry a safe working load not less
than specified, excluding the cost of steel reinforcement but
including the cost of boring, with bentonite solution and
temporary casing of appropriate length for setting out and
removal of same and the length of the pile to be embedded in
the pile cap etc. all complete, including removal of excavated
earth with all lifts and leads (Length of pile for payment shall be
measured upto bottom of pile cap).
20.2.1 300 mm dia piles metre 884.70
20.2.2 400 mm dia piles metre 1129.40
20.2.3 450 mm dia piles metre 1388.10
20.2.4 500 mm dia. piles metre 1642.70
20.2.5 600 mm dia piles metre 2186.00
20.2.6 750 mm dia piles metre 3263.50
20.2.7 1000 mm dia piles metre 7349.80
20.2.8 1200 mm dia piles metre 9411.60
20.2.9 1500 mm dia piles metre 13254.50
20.3 Boring, Providing and installing cast in situ single under
reamed piles of specified diameter and length below pile cap in
M-25 cement concrete, to carry a safe working load not less
than specified, excluding the cost of steel reinforcement but
including the cost of boring with bentonite solution and the
length of the pile to be embedded in pile cap etc. all complete.
(Length of pile for payment shall be measured upto to the
bottom of pile cap) :
20.3.1 300 mm dia piles metre 1978.90
20.3.2 400 mm dia piles metre 2309.00
20.3.3 450 mm dia piles metre 2505.00
20.3.4 550 mm dia piles metre 2739.80

206 BCD/SOR_8th Edition_October 2016

 Code Unit Rate Rs.
Description
No.
20.3A 20.3A.1 Making 25 cm (10") dia bore up to 4 mtr depth below metre 107.10
ground with hand auger of approved quality in ordinary
soi! (vide classification of soil item A ) true to plumb and
without eccentri city in any stage of operation and
disposal of the excavated earth up to 50 mtr , Lead in
eluding all lifts , all complete as per approved disign and
direction of E/l Details of cost for 4 piles of 4 m= 16 mtrs
depth )
20.3A.2 63 CM (25) UNDER -REAM Making 63 cm (25) dia under Each 114.30
ream at required with hand auger of approved quality in
ordinary soil (vide classification of soil ifem - A) true to
plumb and without eccentri city in my stage of opration
and disposal of the excavated earth up to 50 mts lead in
eluding all lifts , all complete as per approved design and
direction of (E/l)
20.4 Extra over item No. 23.3 for providing additional bulb in under
reamed piles, under specified dia meter (Only the quantity of extra
bulbs are to be paid).
20.4.1 300mm dia piles each 1284.50
20.4.2 400mm dia piles each 1434.50
20.4.3 450 mm dia piles each 1525.20
20.4.4 550 mm dia piles each 1679.10
20.5 Providing, driving and installing driven Pre-cast reinforced cement
concrete piles of specified diameter and length below the pile cap
in M-25 cement concrete to carry safe working load not less than
specified. With a central through preformed hole with M.S. black
pipe of dia, 40 mm for grouting with cement sand grouting of mix
1:2 (1 cement : 2 coarse sand) under sufficient positive pressure
to ensure complete filling including centring, shuttering, driving
and removing the steel casing pipe and lifting casing etc.
complete but excluding the cost of steel reinforcement. (Length of
pile for payment shall be measured from top of the shoe to the
bottom of pile cap).
20.5.1 400 mm dia piles metre 2150.10
20.5.2 450 mm dia piles metre 2500.80
20.5.3 500 mm dia piles metre 2661.10
20.5.4 550 mm dia piles metre 2959.00
20.5.5 750 mm dia piles metre 5172.60
20.5.6 1000 mm dia piles metre 6913.20
20.6 Vertical load testing of piles in accordance with IS 2911 (Part IV)
including installation of loading platform and preparation of pile
head or construction of test cap and dismantling of test cap after
test etc. complete as per specification & the direction of Engineer
in-charge.
20.6.1 Single pile upto 50 tonne capacity
20.6.1.1 Initial test per test 40527.30
20.6.1.2 Routine test per test 18310.50
20.6.2 Single pile above 50 tonne and upto 100 tonne capacity
20.6.2.1 Initial test per test 49194.30
20.6.2.2 Routine test per test 28076.10
20.6.3 Group of two or more piles upto 50 tonne capacity
20.6.3.1 Initial test per test 59204.00
20.6.3.2 Routine test per test 36010.70

BCD/SOR_8th Edition_October 2016 207

Code Unit Rate Rs.
Description
No.
20.7 Cyclic vertical load testing of pile in accordance with IS Code of
practice IS: 2911 (part IV) including preparation of pile head etc
for.
20.7.1 Single pile
20.7.1.1 Upto 50 tonne capacity pile per test 18310.50
20.7.1.2 Above 50 tonne and upto 100 tonne capacity pile per test 28076.10
20.7.2 Group of two piles
20.7.2.1 Upto 50 tonne capacity each per test 36010.70
20.8 Lateral load testing of single pile in accordance with IS Code of
practice IS : 2911 (Part IV) for determining safe allowable lateral
load on pile :
20.8.1 Upto 50 tonne capacity pile per test 18310.50
20.8.2 Above 50 tonne and upto 100 tonne capacity pile per test 28808.60
20.9 Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ per test 749.80
Sonic Echo Test method in accordance with IS 14893 including
surface preparation of pile top by removing soil, mud, dust &
chipping lean concrete lumps etc. and use of computerised
equipment and high skill trained personal for conducting the test
& submission of results, all complete as per direction of Engineer-
in-charge.
Note :- The inclusion of the above item in the schedule of work
shall be judiciously decided by the technical sanctioning
authority,keeping in view the quality control, type of soil strata &
importance of the project.

208 BCD/SOR_8th Edition_October 2016

 SUB HEAD : 21.0
ALUMINIUM WORK
 BUILDING WORK - Contd.

21.0 Aluminium Work

Code
Description Unit Rate Rs.
No.
21.1 Providing and fixing aluminium work for doors, windows,
ventilators and partitions with extruded built up standard
tubular sections/ appropriate Z sections and other sections of
approved make conforming to IS: 733 and IS: 1285, fixing with
dash fasteners of required dia and size, including necessary
filling up the gaps at junctions, i.e. at top, bottom and sides
with required EPDM rubber/ neoprene gasket etc. Aluminium
sections shall be smooth, rust free, straight, mitred and jointed
mechanically wherever required including cleat angle,
Aluminium snap beading for glazing / aneling,C.P. brass /
stainless steel screws, all complete as per architectural
drawings and the directions of Engineer-in-charge. (Glazing,
paneling and dash fasteners to be paid for separately) :
21.1.1 For fixed portion
21.1.1.1 Anodised aluminium (anodised transparent or dyed to kg 347.90
required shade according to IS: 1868, Minimum anodic
coating of grade AC 15)
21.1.1.2 Powder coated aluminium (minimum thickness of powder kg 378.70
coating 50 micron)
21.1.1.3 Polyester powder coated aluminium (minimum thickness kg 386.40
of polyester powder coating 50 micron)
21.1.2 For shutters of doors, windows & ventilators including
providing and fixing hinges/ pivots and making provision
for fixing of fittings wherever required including the cost of
EPDM rubber / neoprene gasket required (Fittings shall
be paid for separately)
21.1.2.1 Anodised aluminium (anodised transparent or dyed to kg 395.00
required shade according to IS: 1868, Minimum anodic
coating of grade AC 15)
21.1.2.2 Powder coated aluminium (minimum thickness of powder kg 426.40
coating 50 micron)
21.1.2.3 Polyester powder coated aluminium (minimum thickness kg 423.30
of polyester powder coating 50 micron)
21.2 Providing and fixing 12 mm thick prelaminated particle board
flat pressed three layer or graded wood particle board
conforming to IS: 12823 Grade l Type ll, in panelling fixed in
aluminum doors, windows shutters and partition frames with
C.P. brass / stainless steel screws etc. complete as per
architectural drawings and directions of engineer-in-charge.
21.2.1 Pre-laminated particle board with decorative lamination sqm 1032.60
on one side and balancing lamination on other side
21.2.2 Pre-laminated particle board with decorative lamination sqm 1083.90
on both sides

209 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
21.3 Providing and fixing glazing in aluminium door, window, ventilator
shutters and partitions etc. with EPDM rubber / neoprene gasket etc.
complete as per the architectural drawings and the directions of
engineer-in-charge . (Cost of aluminium snap beading shall be paid in
basic item):
21.3.1 With float glass panes of 4.0 mm thickness sqm 768.30
21.3.2 With float glass panes of 5.50 mm thickness sqm 998.40
21.3.3 With float glass panes of 8 mm thickness sqm 1299.80
21.4 Providing and fixing double action hydraulic floor spring of approved
brand and manufacture conforming to IS : 6315, having brand logo
embossed on the body / plate with double spring mechanism and door
weight upto 125 kg, for doors, including cost of cutting
floors,embedding in floors as required and making good the same
matching to the existing floor finishing and cover plates with brass pivot
and single piece M.S. sheet outer box with slide plate etc. complete
asper the direction of Engineer-in-charge.
21.4.1 With stainless steel cover plate minimum 1.25 mm thickness each 2073.90
21.4.2 With brass cover plate minimum 1.25 mm thickness each 2257.00
21.5 Providing and fixing powder coated aluminium work (minimum kg 454.90
thickness of powder coating 50 micron) consisting of tee/ angle
sections, of approved make conforming to IS : 733 in frames of false
ceiling including aluminium angle cleats with necessary C.P. brass/
stainless steel sunk screws, aluminium perimeter angles fixed to wall
with stainless steel rawl plugs @ 450 mm centre to centre and fixing the
frame work to G.I. level adjusting hangers 6 mm dia. with necessary
cadmium plated machine screws all complete as per approved
architectural drawings and direction of the Engineer-incharge (level
adjusting hangers, ceiling cleats and expansion hold fasteners to be
paid for separately).
21.6 Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto each 107.40
1200mm length), fixed to roof slabs by means of ceiling cleats made out
of G.I. flat 40x3mm size 60 mm long and stainless steel expandable dash
fastener of 12.5 mm dia and 50 mm long, complete as per direction of
Engineer -in-charge.
21.7 Providing and fixing machine moulded aluminium covering of approved
pattern & design, made out of machine cut aluminium sheet and
machine holed for receiving dash fastener, over expansion joints on
vertical surfaces/ceiling floors, the fixing on plate in one row on one
side of joint only shall be done with stainless steel dash fasteners of 8
mm dia and 75 mm long bolt including providing aluminium washers 2
mm thick & 15 mm dia , at a staggered pitch of 200mm centre to centre
including drilling holes in the receiving surface and providing
expandable plastic sleeves in holes etc. complete as per direction of
Engineer-in-charge.

21.7.1 Anodised aluminium sheet 2.5mm thick (anodised transparent or kg 478.00

dyed to required shade according to IS: 1868, Minimum anodic
coating of grade AC 15)
21.7.2 Powder coated aluminium sheet 2.5mm thick (minimum thickness kg 508.80
of powder coating 50 micron)

BCD/SOR_8th Edition_October 2016 210

Code
Description Unit Rate Rs.
No.
21.8 Filling the gap in between aluminium frame & adjacent RCC/ Brick/Stone
work by providing weather silicon sealant over backer rod of approved
quality as per architectural drawings and direction of Engineer-in-
charge complete.
21.8.1 Upto 5mm depth and 5 mm width metre 87.00
21.9 Extra for applying additional anodic coating AC 25 instead of AC 15 to
aluminium extruded sections.
21.9.1 For fixed portion kg 12.20
21.9.2 For shutters of doors, windows & ventilators kg 12.20
21.10 Providing and fixing double glazed hermetically sealed glazing in sqm 3464.40
aluminium windows, ventilators and partition etc. with 6 mm thick clear
float glass both side, having 12 mm air gap, including providing EPDM
gasket, perforated aluminium spacers, desiccants, sealant (Both primary
and secondary sealant) etc. as per specifications,drawings and direction
of Engineer-in-charge complete.
21.11 Providing and fixing stainless steel (SS 304 grade) adjustable friction
windows stays of approved quality with necessary stainless steel
screws etc. to the side hung windows as per direction of Engineer-in-
charge complete.
21.11.1 205 X 19 mm each 219.40
21.11.2 255 X 19 mm each 271.90
21.11.3 355 X 19 mm each 345.20
21.11.4 510 X 19 mm each 607.60
21.11.5 710 X 19 mm each 1047.00
21.12 Providing and fixing aluminium tubular handle bar 32 mm outer dia,3.0
mm thick & 2100 mm long with SS screws etc .complete as per direction
of Engineer-in-Charge.

21.12.1 Anodized (AC 15 ) aluminium tubular handle bar each 484.00

21.12.2 Powder coated minimum thickness 50 micron aluminium tubular each 531.90
handle bar
21.12.3 Polyester powder coated minimum thickness 50 micron aluminium each 571.90
tubular handle bar
21.13 Providing and fixing 100mm brass locks (best make of approved quality) each 380.50
for aluminium doors including necessary cutting and making good etc.
complete.
21.14 Providing and fixing anodised aluminium (anodised transparent or dyed kg 323.20
to required shade according to IS: 1868. Minimum anodic coating of
grade AC 15) sub frame work for windows and ventilators with extruded
built up standard tubular sections of approved make conforming to IS:
733 and IS: 1285, fixed with dash fastener of required dia and size (Dash
fastener to be paid for separately).
21.15 Providing and fixing aluminium casement windows fastener of required
length for aluminium windows with necessary screws etc. complete.
21.15.1 Anodized (AC 15) aluminium each 52.90
21.15.2 Powder coated minimum thickness 50 micron aluminium each 54.10
21.15.3 Polyester powder coated minimum thickness 50 micron aluminium each 52.90

211 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
21.16 Providing and fixing aluminium round shape handle of outer dia 100mm
with SS screws etc. complete as per direction of Engineer in-charge
21.16.1 Anodized (AC 15 ) aluminium each 63.90
21.16.2 Powder coated minimum thickness 50 micron aluminium each 70.00

21.16.3 Polyester powder coated minimum thickness 50 micron each 76.10

aluminium
21.17 Providing and fixing anodised aluminium grill (anodised transparent or kg 404.90
dyed to required shade according to IS: 1868 with minimum anodic
coating of grade AC 15) of approved design/pattern, with approved
standard section and fixed to the existing window frame with C.P.
brass/ stainless steel screws @ 200 mm centre to centre, including
cutting the grill to proper opening size for fixing and operation of
handles and fixing approved anodised aluminium standard section
around the opening, all complete as per requirement and direction of
Engineer-in-charge. (Only weight of grill to be easured for payment).
21.18 Providing and fixing 12 mm thick frameless toughened glass door sqm 4761.50
shutter of approved brand and manufacture, including providing and
fixing top & bottom pivot & spring type fixing arrangement and making
necessary holes etc. for fixing required door fittings, all complete as per
direction of Engineer-in-charge (Door handle, lock and stopper etc.to be
paid separately).

BCD/SOR_8th Edition_October 2016 212

 SUB HEAD : 22.0
WATER PROOFING
 BUILDING WORK - Contd.

22.0 Water Proofing

Code
Description Unit Rate Rs.
No.
22.1 Providing and laying integral cement based treatment for water .
proofing on horizontal surfaces at all levels as directed by Engineer-in-
charge and consisting of: 1) 1st layer of 20 mm thick approved and
specified rough stone slab over a 25 mm thick base of cement mortar
1:3 (1 cement:3 coarse sand) mixed with water proofing compund
conforming to IS: 12645 in the recommnded proportion. Joints sealed
and grouted with cement slurry mixed with water proofing compound
conforming to IS: 12645 in proportions recommended by the
manufacturer. II) 2nd'c!ass layer of 25 mm thick cement mortar 1:3 (1
cement:3 coarse sand) mixed with water proofing compound in
recommended proportions. Ill) Finishing top with stone aggregate of 10
mm to 12 mm nominal size spreadidng @ 8 cudm/sqm thoroughly
embedded in the 2nd layer.
22.1.1 Using rough kota sotne. sqm 1021.10
22.1.2 Using rough red sand stone. sqm 916.10
22.2 Providing and laying integral cement based treatment for water
proofing on the vertical surface by fixing sspecified stone slab 20 mm
thick with cemm slurry mixed with water proofing compound
conforming to IS: 2645 in recommended proportion with a gap of 20
mm (minimum) between stone slabs and the receiving surfaces and
filling the gaps with neat cement slurry mixed with water proofing
compound and finishing the exterior of stone slab with cement
mortar1:4 (1 cement:4 coarse sand) 20 mm thick with neat cement
punning mixed with water proofing compound in recommended
proportion complete at all levels and as directed by Engineer-in-charge.
22.2.1 Using rough kota stone sqm 1271.50
22.2.2 Using rough red sand stone. sqm 1164.10
22.3 Providing and laying water proofing treatment to vertical and horizontal sqm 389.10
surfaces of depressed portions of W.C. kitchen and the like consisting
of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with
water proofing compound conforming tc IS 2645 in recommended
proportions.(ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3
coarse sand)mixed with water proofing compound in recommended
proportion, (iii) Illrd course of applying blown or/residual bitumen aplied
hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC
sheet.(Overlaps at joints of PVC shet should be 100 mm wide and
pasted to each other with bitumen @ 1.7 kg/sqni).
22.4 Providing and Placing in position suitable PVC water stops for
construction/expansion joints between two RCC memberrs and fixed to
the reinforfement with binding wire before pouring concrete etc.
complete
22.4.1 Serrated with central buld (225 mm wide, 8-11 mm thick) m 506.60
22.4.2 Dumb bell with Central bulb (180 mm wide, 8 mm thick) m 481.10
22.4.3 Kickers (320 mm wide, 5 mm thick) m 462.80

213 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
22.5 Providing and laying in sssitu five course water proofing treatment with sqm 342.10
glass fibre tissue reinforced bitumen over roof consisting of first coat of
bitumen primer @ 0.40 kg. per sqm, 2nd & 4th courses of bonding
material® 1.60 kg. per sqm which shall consist of blown type bitumen
of grade 85/25 conforming to IS: 702, third layer of glass ffibre tissuue
course as specified, fifth, the top most layer of stone grit 6 mm and
down size or pea-sized gravel sprad @ 6 dmJ per sqm including
preparation of surface excluding grading for slope etc. complete.
22.6 Providing and laying in situ seven course water profing treatment with sqm 536.50
flass fibre tissue reinforced bitumen over roof consisting of first coat of
bitumen primer @ 0.40 Kg, per sqm . 2nd , 4th $ 6th courses of
bonding material @ 1.60 kg, per sqm , which shall consist of blown
typw bitumen of grade 55/25 conforming to IS : 702 , third and fifth
layers of glass fibre tissue course as specified , seventh , the top pea-
sized grsvel spread @ 6 dm3 per sqm , including prepatation of surface
excluding grading for slope etc. complete.
22.7 Providing and laying in situ nine course water proofing treatment with sqm 729.90
glass fibre tissue reinforced bitumen over roof consisting of first coat of
bitumen primer @ 0.40 kg. per sqm , 2nd , 4th , 6th , 8th coures of
bonding material @ 1.60 kg. per sqm , which shall consist of blown
type bitumen of grade 55/25 conforming to IS -702 , third , fifith and
seventh courses of flass fibre tissue , as specified , ninth, the top most
layer of stone grit 6 mm and down size or pea-sized gravel spread @ 6
z
dm per sqm including preparation of surface ' excluding grading for
slope etc, compete.
22.8 Providing and laying integral cement based water proofing treatment
including prepatation of surface as required for treatment of roofs,
balconies , terraces etc, consisting of following operations. (a) Applying
and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement
admixed with proprietary water -proofing compound cleaning the
surface before treatment, (b) Laying cement concrete using broken
bricks / brick bats 25 mm to 100 mm size with 50 % of cement mortar
1:5 (1 cement: 5 coarse sand ) admixed with proprietary water proofing
compound conforming to IS : 2645 over 20 mm thick layer of cement
mortar of mix 1:5 (1 cement: 5 coarse sand ) admixed with proprietary
water froofing compound conforming to IS 2545 to reuired slope and
treating similary the adjoining walls upto 300 mm height including
rounding of junctions, or walls ad slabs. (c) After two days of proper
curing applying a secoung coat of cement slurry admixed with
proprietary water proofing compound conforming to IS : 2645. (d)
Finishing the surface with 20 mm thick jointless cement mortar of mix
1:4 (1 cement: 4 coarse sand ) admixed with proprietary water proofing
compound conforming to IS : 2645 and finally finishing the surface with
trowel with neat cement slurry and making of 300 x 300 mm square. (e)
The whole terrace so finished shall be flooded with water for a
minimum period of two weeks for curing and for final test, All above
operations to be done in order and as directed and specifed by the
Engineer-in-Charge.
22.8.1 With average thickness of 120 mm and minimum thickness sqm 714.20
at khurras point to be 65 ..

BCD/SOR_8th Edition_October 2016 214

Code
Description Unit Rate Rs.
No.
22.9.1 Providing and laying in situ seven course water proofing treatment with sqm 409.70
APP (Atactic poly-propylene) modified Polymeric membrane over roof
consisting of first coat of bitumen primer @ 0.40Kg per sqm, 2nd, 4th &
6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of
blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th
layers of roofing membrane APP modified Polymeric membrane
1.5mm thick of 2.25 Kg/sqm weight consisting of five layers
prefabricated with centre core as 20micron HMHDPE film sandwitched
on both sides with polymeric mix and the polymeric mix is protected on
both side with 20micron HMHDPE film. 7th, the top most layer shall be
finished with brick tiles of class designation 100 grouted with cement
mortar 1:3 (lcement:3 fine sand) mixed with 2% integral water proofing
compound by weight of cement over a 12mm layer of cement mortar
1:3 (1 cement: 3 fine sand) and finished neat which shall be paid for
separately .
22.9.2 Providing and laying in situ five course water proofing treatment with sqm 313.50
APP (Atactic Polypropylene) modified Polymeric membrane over roof
consisting of first coat of bitumen primer @ 0.40Kg per sqm, 2nd & 4th
courses of bonding material @ 1.20 Kg/sqm, which shall consist of
blown type bitumen of grade 85/25 conforming to IS: 702, 3rd layer of
roofing membrane APP modified Polymeric membrane 2.0mm thick of
3.00 Kg/sqm weight consisting of five layers prefabricated with centre
core as lOOmicron HMHDPE film sandwitched on both sides with
polymeric mix and the polymeric mix is protected on both side with
20micron HMHDPE film. 5th, the top most layer shall be finished with
brick tiles of class designation 100 grouted with cement mortar 1:3 (1
cement: 3 fine sand) mixed with 2% integral water proofing compound
by weight of cement over a 12mm layer of cement mortar 1:3 (1
cement : 3 fine sand) and finished neat which shall be paid for
separately as per DSR Item No. 12.19.
22.9.3 Providing and laying in situ seven course water proofing treatment with sqm 514.40
APP (AtacticPolypropylene) modified Polymeric membrane over roof
consisting of first coat of bitumen primer @ 0.40Kg per sqm, 2nd, 4th &
6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of
blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th
layers of roofing membrane APP modified Polymeric membrane
2.0mm thick of 3.00 Kg/sqm weight consisting of five layers
prefabricated with centre core as 1 OOmicron HMHDPE film
sandwitched on both sides with polymeric mix and the polymeric mix is
protected on both side with 20micron HMHDPE film. 7th, the top most
layer shall be finished with brick tiles of class designation 100 grouted
with cement mortar 1:3 (1 cement: 3 fine sand) mixed with 2% integral
water proofing compound by weight of cement over a 12 mm layer of
cement mortar 1:3 ( 1 cement: 3 fine sand) and finished neat which
shall be paid for separately .

215 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
22.18 Providing and fixing APP (Atactic Polypropylene Polymer) modified
prefabricated five layer 2 mm thick water proofing membrance, black finished
reinforced with glass fibre matt consisting of a coat of bitumen primer for
bitumen membrane @ 0.40 litre/ sqm by the same membrance manufacture
of density at 25°C, 0.87 - 0.89 kg/ litre and viscocity 70 - 160 cps. Over the
primer coat the layer of membrane shall be laid using Butane torch and
sealing all joints etc., and preparing the surface complete. The vital physical
and chemical parameters of the membrane shall be as under : Joint strength
in longitudinal and transverse direction at 23°C as 350/300 N/ 5cm. Tear
strength in longitudinal and transverse direction as 60/80N. Softening point
of membrane not less than 150°C. Cold flexibility shall be upto -2°C when
tested in accordance with ASTM, D - 5147. The laying of membrane shall be
got done through the authorised applicator of the manufacture of membrane.

22.18.1 2 mm (for corrugated roof sheets). sqm 339.50

22.19 Providing and laying APP (Atactic Polypropylene Polymer) modified
prefabricated five layer, 3 mm thick water proofing membrane, black finished
reinforced with glass fibre matt consisting of a coat of bitumen primer for
bitumen membrane @0.40 litre/ sqm by the same membrane manufactured
of density at 25° C, 0.87 - 0.89 kg/ litre and viscocity 70 - 160 cps. Over the
primer coat the layer of membrane shall be laid using butane torch and
sealing all joints etc., and preparing the surface complete. The vital physical
and chemical parameters of the membrane shall be as under : Joint strength
in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear
strength in longitudinal and transverse direction as 60/80N. Softening point
of membrane not less than 150°C. Cold flexibility shall be upto -2°C when
tested in accordance with ASTM, D - 5147. The laying of membrane shall be
got done through the authorised applicator of the manufacturer of
membrane.
22.19.1 3 mm thick. sqm 393.20
22.20 Providing and laying APP (Atactic Polypropylene Polymer) modified
prefabricated five layer 3 mm thick water proofing membrane, black finished
reinforced with non-woven polyester matt consisting of a coat of bitumen
primer for bitumen membrane @ 0.40 litre/ sqm by the same membrane
manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps.
Over the primer coat the layer of membrane shall be laid using Butane Torch
and sealing all joints etc., and preparing the surface complete. The vital
physical and chemical parameters of the membrane shall be as under : Joint
strength in longitudinal and transverse direction at 23°C as 650/450N/5 cm.
Tear strength in longitudinal and transverse direction as 300/250N. Softening
point of membrane not less than 150°C. Cold flexibility shall be upto -2°C
when tested in accordance with ASTM, D - 5147. The laying of membrane
shall be got done through the authorised applicator of the manufacturer of
membrane.
22.20.1 3 mm thick. sqm 444.20
22.21 Extra for covering top of membrane with Geotextile, 120 gsm non woven, sqm 62.40
100%polyester of thickness 1 to 1.25 mm bonded to the membrane with
intermittent touch by heating the membrane by Butane Torch as per
manufactures recommendation.

BCD/SOR_8th Edition_October 2016 216

SUB HEAD : 23.0
HORTICULTURE
& LANDSCAPING
 BUILDING WORK - Contd.

23.0 Horticulture & Landscaping

Code
Description Unit Rate Rs.
No.
23.1 Trenching in ordinary soil upto a depth of 60 cm including removal cum 26.70
and stacking of serviceable materials and then disposing of by
spreading and neatly levelling within a lead of 50 m and making
up the trenched area to proper levels by filling with earth or earth
mixed with sludge of/and manure before and after flooding trench
with water (encluding cost of imported earth,sludge or manure).
23.2 Supplying and stacking of good earth at site including royalty but cum 85.50
excluding carriage (earth measusred in stacks will be reduced by
20% for payment).
23.3 Supplying and stacking Sludge at site including royalty and cum 241.60
carriage (Sludge measusred in stacks will be reduced by 8% for
payment).
23.4 Supplying and stacking a' site dump manure from approved
source, excluding carriage (manure measured in stacks will be
reduced by 8% for payment)
23.4.1 Screened through sieve of l.S. designation 20 mm cum 25.00
23.4.2 Screened through sieve of l.S. Designation 16 mm cum 37.10
23.4,3 Screened through sieve of l.S. designation 4.75 mm cum 46.70
23.5 Rough dressing the trenched ground including breaking clods. 100sqm 51.30
23.6 Uprooting weeds form the trenched area after 10 to 15 days of its 100sqm 169.80
flooding with water including disposal of uprooted vegetation.
23.7 Fine dressing the ground 100sqm 123.80
23.8 Spreading of sludge, dump manure or/and good earth in required cum 18.00
thickness (Cost of sludge, dump manure or/and good earth to be
paid separately).
23.9 Mixing earth and sjudge or manure in porportion specified or cum 12.40
directed.
23.10 Grassing with 'Doob' grass including watering and maintenance of
the lawn for 30 days or more tili the grass forms a thick lawn free
form weeds and fit for mowing including supplying good earth if
needed.
23.10.1 In rows 15 cm apart in either direction. 100sqm 192.00
23.10.2 In rows 7.5 cm apart in either direction. 100sqm 402.90
23.10.3 In rows 5 cm apart in either direction. 100sqm 616.50
23.11 Renovating lawns including weeding.cheeling the grass,forking 100 sqm 1169.60
the ground, top dressing with sludge or manure,mixing the same
with forked soil,watering and maintaining the lawn for 30 days or
more till the grass forms a thich lawn free from weeds and fit for
mowing and disposal of rubbish as directed, including supplying
good earth if needed but excluding the cost of sludge or manure.

217 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
23.12 Uprooting rank vegetation and weeds by digging the area to a 100sqm 2051.80
depth of 60 cm removing all weeds and other growth with roots by
forking repeatedly, breaking clods, rough dressing, flooding with
water, uprooting fresh growths after 10 to 15 days and then fine
dressing for planting new grass, including disposal of al! rubbish
with all leads and lifts.
23.13 Preparation of beds for hedging and shrubbery by excavating 60 cum 75.50
cm deep and trenching the excavated base to a further depth of
30 cm, refilling the excavated earth after breaking clods and
mixing with sludge or manure in the ratio of 8:1 (8 parts of
stacked volume of earth after reduction by 20% : one part of
stacked volume of sludge or manure after reduction by 8%).
flooding with water, filling with earth if necessary, watering and
finally fine dressing, levelling etc. including stacking and disposal
of materials declared unserviceable and surplus earth by
spreading and levelling as drected, within a lead of 50 m lift upto
1.5 m complete (cost of sludge, manure or extra earth to be paid
for separately).
23.14 Digging holes in ordinary soil and refilling the same with the
excavated earth mixed with manure or sludge in the ratio of 2;1 by
volume (2 parts of stacked volume of earth after reduction by
20% : 1 part of stacked volume of manure after reduction by 8%)
flooding with water,dressing including removal of rubbish and
surplus earth, if any with all leads and lifts (cost of manure, sludge
or extra good earth if needed to be paid for separately):
23.14.1 Holes 1.2 m dia, And 1.2 m deep. each 324.30
23.14.2 Holes 60 cm ciia. And 60 cm deep. each 42.20
23.15 Half brick circular tree guard in 50 class designation bricks,
internal diameter 1.25 metre and height 1.? metre above ground
and 0.20 m below ground bottom two courses laid dry and top
three courses in lime mortar 1:2(1 lime putty:2 surkhi) or cement
ortar 1:6 (1 cement:6 fine sand) and the intermediate courses
being in dry honey comb masonry as per design complete:
23.15.1 With F.P.S. Bricks each 1556.20
23.16 Providing and fixing M.S. fiat iron tree guard 60 cm dia. And 2 m each 2547.90
high above ground level formed of 4 nos. 25x6 mm and 8 nos.
25x3 mm vertical M.S. flats hvetted to 3 nos. 25x6 mm M.S. flat
iron rings in two halves, bolted together with 8 mm dia. And 30
mm long bolts including painting two coats with paint of approved
brand and manufacture over a coat of priming, complete in all
respects.
23.19 Edging with bricks laid dry length wise including excavation,
refilling, consolidating with hand packing and spreading neatly
susrplus earth within a lead of 50 m:
23.19.1 100A class designation.
23.19.1.1 F.P.S.Bricks m 38.40
23.19.1.2 100Bclass designation. m 35.60

BCD/SOR_8th Edition_October 2016 218

Code
Description Unit Rate Rs.
No.
23.20 Filling mixture of earth and sludge or manure in the deisired m 5.70
proportion in trenches, flooding with water and levelling (cost of
supplying earth and sludge nr manure and mixing excluded).
23.21 Excavation in dumped stones or malba including stacking of cum 174.10
serviveable and unserviceable material separately and disposal of
unserviceable material lead upto 50 m and lift upto 1.5 m
disposed material to be neatly dressed.
23.22 Excavation in bajri path including stacking of serviceable and cum 193.40
unserviceable material lead upto 50 m and lift upto 1.5 m
disposed material to be neatly dressed,
23.23 Excavation in water bound macadam road including stacking the cum 235.70
serviceable and unserviceable material separatedly and disposal
of unserviceabel material lead upto 50 m and lift upto 1.5 m
disposed material to be neatly dressed.
23.24 Flooding the ground with water including making kiaries and 100sqm 115.20
dismantelling the same.

219 BCD/SOR_8th Edition_October 2016

 SUB HEAD : 24.0
RAIN WATER HARVESTING
& TUBE WELLS
 BUILDING WORK - Contd.

24.0 Rain Water Harvesting & Tube Wells

Code
Description Unit Rate Rs.
No.
24.1 Boring/drilling bore well of required dia for casing/ strainer
pipe, by suitable method prescribed in IS: 2800 (part I),
including collecting samples from different strata, preparing
and submitting strata chart/
bore log, including hire & running charges of all
equipments, tools, plants & machineries required for the job,
all complete as per direction of Engineer -in-charge, upto 90
metre depth below ground level.
24.1.1 All types of soil
24.1.1.1 300 mm dia metre 378.00
24.1.1.2 350 mm dia metre 413.50
24.1.1.3 400 mm dia metre 529.30
24.1.2 Rocky strata including Boulders
24.1.2.1 300 mm dia metre 833.10
24.1.2.2 350 mm dia metre 859.70
24.1.2.3 400 mm dia metre 953.00
24.2 Boring/drilling bore well of required dia for casing/ strainer
pipe, by suitable method prescribed in IS: 2800 (part I),
including collecting samples from different strata, preparing
and submitting strata chart/
bore log, including hire & running charges of all
equipments, tools,plants & machineries required for the job,
all complete as per direction of Engineer -in-charge, beyond
90 metre & upto 150 metre depth below ground level.
24.2.1 All types of soil
24.2.1.1 300 mm dia metre 441.10
24.2.1.2 350 mm dia metre 509.40
24.2.1.3 400 mm dia metre 691.80
24.2.2 Rocky strata including Boulders
24.2.2.1 300 mm dia metre 881.20
24.2.2.2 350 mm dia metre 904.70
24.2.2.3 400 mm dia metre 1128.50
24.3 Supplying, assembling, lowering and fixing in vertical
position in bore well, unplasticized PVC medium well casing
(CM) pipe of required dia, conforming to IS: 12818, including
required hire and labour charges, fittings & accessories etc.
all complete, for all depths,as per direction of Engineer -in-
charge.
24.3.1 100 mm nominal size dia metre 444.20
24.3.2 150 mm nominal size dia metre 615.30
24.3.3 200 mm nominal size dia metre 921.70
24.3.4 50 mm nominal size dia metre 190.10
24.3.5 75 mm nominal size dia metre 328.50

220 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
24.4 Supplying, assembling, lowering and fixing in vertical
position in bore well unplasticized PVC medium well screen
(RMS) pipes with ribs, conforming to IS: 12818, including
hire & labour charges, fittings & accessories etc. all
complete, for all depths, as per direction of Engineer-in-
charge.
24.4.1 100 mm nominal size dia metre 468.80
24.4.2 150 mm nominal size dia metre 554.30
24.4.3 200 mm nominal size dia metre 861.00
24.4.4 50 mm nominal size dia metre 310.00
24.4.5 75 mm nominal size dia metre 420.30
24.5 Supplying, filling, spreading & leveling stone boulders of cum 489.70
size range 5 cm to 20 cm, in recharge pit, in the required
thickness, for all leads & lifts, all complete as per direction
of Engineer-in-charge.
24.6 Supplying, filling, spreading & leveling gravels of size range cum 917.00
5 mm to 10 mm, in the recharge pit, over the existing layer of
boulders, in required thickness, for all leads & lifts, all
complete as per direction
of Engineer-in-charge.
24.7 Supplying, filling, spreading & leveling coarse sand of size cum 855.90
range 1.5 mm to 2 mm in recharge pit, in required thickness
over gravel layer, for all leads & lifts, all complete as per
direction of Engineer -in-charge.
24.8 Gravel packing in tubewell construction in accordance with cum 990.10
IS: 4097,including providing gravel fine/ medium/ coarse, in
required grading & sizes as per actual requirement, all
complete as per direction of Engineer-in-charge.
24.9 Providing and fixing factory made precast RCC perforated each 1007.50
drain covers, having concrete of strength not less than M-25,
of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos
longitudinal & 9nos cross sectional T.M.T. hoop bars,
including providing 50 mm dia perforations @ 100 to 125
mm c/c, including providing edge binding with M.S. flats of
size 50 mm x 1.6 mm complete, all as per direction
of Engineer-in-charge.
24.10 Supplying, assembling, lowering and fixing in vertical
position in bore well, ERW (Electric Resistance Welded) FE
410 mild steel screwed and socketed/ plain ended casing
pipes of required dia,conforming to IS: 4270, of reputed &
approved make, including painted with outside surface with
two coats of anticorrosive paint of approved brand and
manufacture, including required hire & labour charges,
fittings & accessories, all complete, for all depths, as per
direction of Engineer-in-charge.

BCD/SOR_8th Edition_October 2016 221

24.10 24.10.1 100 mm nominal size dia having minimum wall metre 1010.10
thickness 5.00 mm
24.10.2 150 mm nominal size dia having minimum wall metre 1381.20
thickness 5.00 mm
24.10.3 200 mm nominal size dia having minimum wall metre 1696.20
thickness 5.40 mm
24.11 Supplying, assembling, lowering and fixing in vertical
position in bore well, ERW (Electric Resistance Welded) FE
410 plain slotted (having slot of size 1.6/3.2 mm) mild steel
threaded and socketed /
plain bevel ended pipe (type A) of required dia, conforming
to IS: 8110, of reputed and approved make, having wall
thickness not less than 5.40 mm, including painted with
outside surface with two coats of anticorrosive bitumestic
paint of approved brand and manufacture,including hire &
labour charges, fittings & accessories, all complete,for all
depths, as per direction of Engineer -in-charge.
24.11.1 100 mm nominal size dia metre 1072.40
24.11.2 150 mm nominal size dia metre 1464.30
24.11.3 200 mm nominal size dia metre 1780.10
24.12 Development of tube well in accordance with IS : 2800 (part hour 649.40
I) and IS: 11189, to establish maximum rate of usable water
yield without sand content (beyond permissible limit), with
required capacity air compressor, running the compressor
for required time till well is fully develo ped, measuring yield
of well by "V" notch method or any other approved method,
measuring static level & draw down etc. by step draw down
method, collecting water samples & getting tested in
approved laboratory, i/c disinfection of tubewell, all
complete,including hire & labour charges of air compressor,
tools & accessories etc., all as per requirement and direction
of Engineer-in-charge.
24.13 Providing and fixing suitable size threaded mild steel cap or
spot welded plate to the top of bore well housing/ casing
pipe, removable as per requirement, all complete for
borewell of:
24.13.1 100 mm dia each 166.60
24.13.2 150 mm dia each 205.10
24.13.3 200 mm dia each 256.40
24.14 Providing and fixing M.S. clamp of required dia to the top of
casing/ housing pipe of tubewell as per IS: 2800 (part I),
including necessary bolts & nuts of required size complete.
24.14.1 100 mm clamp each 974.60
24.14.2 150 mm clamp each 1031.10
24.14.3 200 mm clamp each 1169.50
24.15 Providing and fixing Bail plug/ Bottom plug of required dia
to the bottom of pipe assembly of tubewell as per IS:2800
(part I).
24.15.1 100 mm dia each 205.60
24.15.2 150 mm dia each 254.50
24.15.3 200 mm dia each 278.90

222 BCD/SOR_8th Edition_October 2016

 SUB HEAD : 25.0
CONSERVATION OF
HERITAGE BUILDING
 BUILDING WORK - Contd.

25.0 Conservation of Heritage Building

Code
Description Unit Rate Rs.
No.
25.1 Raking out joints of stone masonry surface to the required sqm 17.00
width and depth, with due care and precaution, by
mechanical / manual means, including preparing and
cleaning the surface for re-pointing/ refilling of joints,
including disposal of rubbish to the dumping ground
within 50 metre lead.
25.2 Providing and fixing double scaffolding system (cup lock sqm 126.20
type) on the exterior side of building/structure, upto 25 metre
height, above ground level, including additional rows of
scaffolding in stepped manner as per requirement of site,
made with 40mm dia M.S. tube, placed 1.5 metre centre to
centre, horizontal & vertical tubes joint with cup & lock
system with M.S. Tubes, M.S. tube challis, M.S. clamps and
staircase system in the scaffolding for working platform etc.
and maintaining it in a serviceable condition for execution of
work of cleaning and/ or pointing and/ or applying chemical
and removing it thereafter. The scaffolding system shall be
stiffened with bracings, runners, connecting with the
building etc, wherever required, if feasible, for inspection of
work at required locations with essential safety features for
the workmen etc., complete as per directions and approval of
Engineer-in-charge.
Note:- (1) The elevational area of the scaffolding shall be
measured for payment purpose.
(2) The payment will be made once only for execution of all items
for such works.
25.3 Cleaning the sand stone surface and removing dirt, dust, bird sqm 51.00
dropping, grease, oil, algae, fungus, monkey beats, vegetable
growth etc., including providing, applying and washing the
surface with liquid Ammonia Chemical of 5% solution and
other chemical cleaning agent as approved by chaeological
Survey of India/ Engineer-incharge, of approved brand and
manufacturer, with the help of required scrubbers and also
cleaning with machine operated water jet mixed with desired
quantity of fine silica where ever required, without causing
any scratching/ damage to the stone surface and finally
washing the surface with clean water with the help of
pressure jet machine, complete in all respect, including
taking all precautions to safeguard ventilators, windows,
doors etc. by suitable covering so as to avoid any damage to
the building/ structure, all as per direction of Engineer-in-
charge (The rate is inclusive of all materials & labours
involved except scaffolding).

223 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
25.4 Providing and applying antifungal wash treatment using 3% sqm 23.50
solution of sodium pentachlorophenate, of reputed brand
and manufacturer,on cleaned sand stone surface at desired
locations as per direction of Engineer-in-charge (The rate is
inclusive of all materials & labours involved except
scaffolding).
25.5 Ruled / Flush pointing on Red sand stone masonry surface sqm 92.90
with lime, surkhi and marble dust mortar in the ratio of
1:1.5:1/2 {One lime: 1.5 surkhi (50% red and 50% light yellow
surkhi ):1/2 marble dust}. (The rate is inclusive of all
materials & labours involved except scaffolding).
25.6 Ruled/ Flush pointing on White sand stone masonry surface sqm 92.90
with lime, surkhi and marble dust mortar in the ratio of
1:1.5:1/2 {One lime : 1.5 surkhi (15% dark red and 85% light
yellow surkhi) : 1/2 marble dust}. (The rate is inclusive of all
materials & labours involved except scaffolding).
25.7 Applying two or more coat of Ethyl Silicate chemical as sqm 268.40
approved by Archaeological Survey of India/ Engineer-in-
charge, of approved brand and manufacturer, with brush or
spray on the existing stone masonry surface till there is no
further absorption of chemical by stone surface, including
protecting the applied surface from direct sunlight by
suitable means during application, all complete as per
direction of the Engineer-in-Charge (The rate is inclusive of
all materials & labours involved except scaffolding).
25.8 Applying breathable, non-reactive, antifungal, and water sqm 78.00
repellant Silane/ Siloxane chemical as approved by
Archaeological Survey of India/ Engineer-in-charge, of
approved brand and manufacture,diluted with solvent
mineral Turpentine oil in the ratio of 1:12 (One part of
approved chemical :12 Part of Turpentine oil), on the existing
sand stone masonry surface with two or more coats to give
uniform application of chemical on the surface, all complete
as per direction of Engineer-In-charge (The rate is nclusive
of all materials & labours involved except scaffolding).

BCD/SOR_8th Edition_October 2016 224

 SUB HEAD : 26.0
STRUCTURAL GLAZING AND
COMPOSITE ALUMINIUM PANEL
 BUILDING WORK - Contd.

26.0 Structural Glazing and Composite Aluminium Panel

Code
Description Unit Rate Rs.
No.
26.1 Providing and supplying aluminium extruded tubular and other kg 355.50
aluminium sections as per the rchitectural drawings and
approved shop drawings , the aluminium quality as per grade
6063 T5 or T6 as per BS74,including super durable powder
coating of 60-80 microns conforming to AAMA 2604 of required
colour and shade as approved by the Engineer-in-Charge. (The
item includes cost of material such as cleats, sleeves, screws
etc. necessary for fabrication of extruded aluminium frame
work. Nothing extra shall be paid on this account).
26.2 Designing, fabricating, testing, protection, installing and fixing kg 2584.70
in position semi (grid) unitized system of structural glazing
(with open joints) for linear as well as curvilinear portions of the
building for all
heights and all levels, including:
a) Structural analysis & design and preparation of shop
drawings for the specified design loads conforming to IS 875
part III (the system must passed the proof test at 1.5 times
design wind pressure without any failure), including functional
design of the aluminum sections for fixing glazing panels of
various thicknesses, aluminium cleats, sleeves and splice
plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc.,
structural and weather silicone sealants, flashings, fire stop
(barrier)-cum-smoke seals, microwave cured EPDM gaskets for
water tightness, pressure equalisation & drainage and
protection against fire hazard including:
b) Fabricating and supplying serrated M.S. hot dip galvanised /
Aluminium alloy of 6005 T5 brackets of required sizes, sections
and profiles etc. to accommodate 3 Dimentional movement for
achieving perfect verticality and fixing structural glazing system
rigidly to the RCC/ masonry/structural steel framework of
building structure using stainless steel anchor fasteners/ bolts,
nylon seperator to prevent bimetallic contacts with nuts and
washers etc. of stainless steel grade 316, of the required
capacity and in required numbers.
c) Providing and filling, two part pump filled, structural silicone
sealant and one part weather silicone sealant compatible with
the structural silicone sealant of required bite size in a clean
and controlled factory / work shop environment , including
double sided spacer tape, setting blocks and backer rod, all of
approved grade, brand and manufacture,as per the approved
sealant design, within and all around the perimeter for holding
glass.

225 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
26.2 d) Providing and fixing in position flashings of solid aluminium
sheet 1 mm thick and of sizes, shapes and profiles, as required
as per the site conditions, to seal the gap between the building
structure and all its interfaces with curtain glazing to make it
watertight.
e) Making provision for drainage of moisture/ water that enters
the curtain glazing system to make it watertight, by
incorporating principles of pressure equalization, providing
suitable gutter profiles at bottom (if required), making
necessary holes of required sizes and of required numbers etc.
complete. This item includes cost of all inputs of designing,
labour for fabricating and installation of aluminium grid,
installation of glazed units, T&P, scaffolding and other
incidental charges including wastages etc., enabling temporary
structures and services, cranes or cradles etc. as described
above and as specified. The item includes the cost of getting all
the structural and functional design including shop drawings
checked by a structural designer, dully approved by Engineer-in-
charge. The item also includes the cost of all mock ups at site,
cost of all samples of the individual components for testing in
an approved laboratory, field tests on the assembled working
structural glazing as specified, cleaning and protection till the
handing over of the building for occupation. In the end, the
Contractor shall provide a water tight structural glazing having
all the performance characteristics etc. all complete as required,
as per the Architectural drawings, as per item description, as
specified,as per the approved shop drawings and as directed by
the Engineerin-Charge.
Note:- 1. The cost of providing extruded aluminium frames,
shadow boxes, extruded aluminium section capping for fixing in
the grooves of the curtain glazing and vermin proof stainless
steel wire mesh shall be paid for separately under relevant items
under this subhead. However, for the purpose of payment, only
the actual area of structural glazing (including width of grooves)
on the external face shall be measured in sqm. up to two
decimal places.
Note:-2. The following performance test are to be conducted on
structural glazing system if area of structural glazing exceeds
2500 Sqm from the certified laboratories accreditated by
BL(National Accreditation Board for Testing and Calibration
boratories), Department of Science &Technologies, India. Cost
of testing is payable separately. The NIT approving authority will
decide the necessity of testing on the basis of cost of the work,
cost of the test and importance of the work. Performance
Testing of Structural glazing system Tests to be conducted in
the NBL Certified laboratories

BCD/SOR_8th Edition_October 2016 226

Code
Description Unit Rate Rs.
No.
26.2 1. Performance Laboratory Test for Air Leakage Test (-50pa to
–300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing
method for a range of testing limit 1 to 200 mVhr”
2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME-
331-09 testing method for a range up to 2000 ml.”
3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA
501.01-05 testing method for a range upto 2000 ml”
4. Structural Performance Deflection and deformation by static
air pressure test (1.5 times desing wind pressure without any
failure) as per ASTME-330-10 testing method for a range upto 50
mm”
5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09
testing method for Qualitative test” Tests to be conducted on
site
6. Onsite Test for Water Leakage for a pressure range 50 kpa to sqm
240 kpa (35psi) upto 2000ml”
26.3 Providing, assembling and supplying vision glass panels (IGUs)
comprising of hermetically-sealed 6-12- 6 mm insulated glass
(double glazed) vision panel units of size and shape as required
and specified, comprising of an outer heat strengthened float
glass 6mm thick, of
approved colour and shade with reflective soft coating on
surface # 2 of approved colour and shade, an inner Heat
strengthned clear float glass 6mm thick, spacer tube 12mm
wide, dessicants, including primary seal and secondary seal
(structural silicone sealant) etc. all
complete for the required performances, as per the Architectural
drawings, as per the approved shop drawings, as specified and
as directed by the Engineer-in-Charge. The IGUs shall be
assembled in the factory/ workshop of the glass processor.
(Payment for fixing of IGU Panels in the curtain glazing is
included in cost of item No.26.2)For payment, only the actual
area of glass on face # 1 of the glass panels (excluding the
areas of the grooves and weather silicone sealant) provided and
fixed in position, shall be measured in sqm.
(i) Coloured tinted float glass 6mm thick substrate with sqm 4146.50
reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat
Strengthened clear Glass of approved make having properties
as visible Light transmittance (VLT) of 25 to 35 %, Light
reflection internal 10 to 15%, light reflection external 10 to 20 %,
shading coefficient (0.25-
0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties
of performance glass shall be decided by technical sanctioning
authority as per the site requirement.

227 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
26.4 Extra for openable side / top hung vision glass panels (IGUs) sqm 3184.30
including providing and supplying at site all accessories and
hardwares for the openable panels as specified and of the
approved make such as
heavy duty stainless steel friction hinges, min 4 -point cremone
locking sets with stainless steel plates, handles, buffers etc.
including necessary stainless steel screws/ fasteners, nuts,
bolts, washers etc. all complete as per the Architectural
drawings, as per the approved shop drawings, as specified and
as directed by the Engineerin- Charge.
26.5 Providing, fabricating and supplying shadow box of required sqm 1712.10
size and shape, for fixing in the spandrel portion of the
structural glazing, in linear as well as curvilinear portions of the
building by providing semi -rigid, inorganic, non-combustible
fibre glass wool insulation 50 mm thick, conforming to IS: 8183
and BS: 3958 Part 5. The insulation layer shall have facing
(factory bonded on surface # 1of the fibre glass insulation
layer), of black non-woven fibre glass tissue of nominal
thickness 0.5 mm and nominal mass not less than 60 gm / sqm,
made of randomly oriented glass fibres distributed in a binder
by a wet-lay process including fixing 1.5 mm thick solid
aluminum sheet backing using, 6 mm thick cement board
including SS rivets, nuts, bolts, washers etc complete.
26.6 Providing and supplying Spandrel Glass Panels comprising of 6
mm thick heat strengthened monolithic float glass of approved
colour and shade with reflective soft coating on surface # 2 of
approved colour and shade so as to match the colour and
shade of the IGUs in the vision panels etc. ,all complete for the
required performances as specified, as per the Architectural
drawings, as per the approved shop drawings, as specified, and
as directed by the Engineer- in- Charge. For payment, only the
actual area of glass on face # 1 of the glass panels (but
excluding the area of grooves and weather silicone sealant)
provided and fixed in position, shall be measured in
sqm.(Payment for fixing of Spandrel Glass Panels in the curtain
glazing is included in cost of relevent Item*).
(i) Coloured tinted float glass 6mm thick substrate with sqm 3005.50
reflective soft coating on face # 2, having properties as visible
Light transmittance (VLT) of 25 to 35 %, Light reflection internal
10 to 15%, light reflection external 10 to 20 %, shading
coefficient (0.25- 0.28) and U value of
3.0 to 3.3 W/m2 degree K etc. . The properties of performance
glass shall be decided by technical sanctioning authority as per
the site requirement.

BCD/SOR_8th Edition_October 2016 228

Code
Description Unit Rate Rs.
No.
26.7 Designing, fabricating, testing, installing and fixing in position
Curtain Wall with Aluminium Composite Panel Cladding, with
open grooves for linear as well as curvilinear portions of the
building , for all heights
and all levels etc. including:
a) Structural analysis & design and preparation of shop
drawings for pressure equalisation or rain screen principle as
required, proper drainage of water to make it watertight
including checking of all the structural and functional design.
b) Providing, fabricating and supplying and fixing panels of
aluminium composite panel cladding in pan shape in metalic
colour of approved shades made out of 4mm thick aluminium
composite panel material consisting of 3mm thick FR grade
mineral core sandwiched between two Aluminium sheets (each
0.5mm thick). The aluminium composite panel cladding sheet
shall be coil coated, with Kynar 500 based PVDF / Lumiflon
based fluoropolymer resin coating of approved colour and
shade on face # 1 and polymer (Service) coating on face # 2 as
specified using stainless steel screws, nuts, bolts, washers,
cleats, weather silicone sealant, backer rods etc.
c) The fastening brackets of Aluminium alloy 6005 T5 / MS with
Hot Dip Galvanised with serrations and serrated washers to
arrest the wind load movement, fasteners, SS 316 Pins and
anchor bolts of approved make in SS 316, Nylon separators to
prevent bi-metallic contacts all complete required to perform as
per pecification and drawing
The item includes cost of all material & labour component, the sqm 3876.30
cost of all mock ups at site, cost of all samples of the individual
components for testing in an approved laboratory, field tests on
the assembled working curtain wall with aluminium composite
panel cladding, cleaning and protection of the curtain wall with
aluminium composite panel cladding till the handing over of the
building for occupation. Base frame work for ACP cladding is
payable under the relevant aluminium item.s The Contractor
shall provide curtain wall with aluminium composite panel
cladding, having all the performance characteristics all
complete , as per the Architectural drawings, as per item
description, as specified, as per the approved shop drawings
and as directed by the Engineer-in-Charge. However, for the
purpose of payment, only the actual area on the external face of
the curtain wall with Aluminum Composite Panel Cladding
(including width of groove) shall be measured in sqm. up to two
decimal places.

229 BCD/SOR_8th Edition_October 2016

 Code
Description Unit Rate Rs.
No.
26.8 "Design supply & installation of suspended Spider Glozing
system designed to withstand the wind pressure as pr IS 875
(Part-III). The Suspended System held with Spider Fittings of SS-
316 Grade Steel of approved manufacturer with glass panel
having 12 mm thick clear toughened glass held together with SS-
316 Grade Stainless steel Spider & bolt assembly with laminated
glass fins 21 mm thick. The Glass fins and glass panel assembly
shall be connected to Slab/beams by means of SS- 316 Grade
stainless steel brackets & Anchor bolts and at the bottom using
SS channel of 50x25x2mm using fastener & anchor bolts, non
staining weather sealants of approved make, Teflon/ nylon
bushes and separators to prevent bi-metallic contacts, all
complete to perform as per specification and approved
drawings. The complete system to be designed to accommodate
thermal expansion & seismic movements etc. The joints
between glass panels (6 to 8 mm) and gaps at the erimeter & in
U channel of the assembly to be filled with non staining weather
sealant, so as to make the entire system fully water proof & dust
proof.
The rate shall include all design, Engineering and shop drawing
including approval from structural designer, labour, T&P,
scaffolding ,other incidental charges including wastage,
enabling temporary services all fitting fixers nut bolts, washer,
Buffer plates, fastener,
anchors, SS channel laminated glass etc. all complete.
For the purpose of payment, actual elevation area of Glazing sqm 3604.70
including thickness of joints and the portion of Glass panel
inside the SS channel shall be measured. "

BCD/SOR_8th Edition_October 2016 230