USER MANUAL

ITON

Uninterruptible Power Supply

 +

-
Introduction
This UPS is specially designed for Personal Computer
with multi-functions. Its light weight, compact design
perfect fits to the limited working environment. The line of
UPS is equipped with boost and buck AVR to stabilize
input voltage range. It is also built-in with DC start
function. This function enables the UPS to be started up
without AC power supplied. Although it's a small UPS, it's
equipped with Smart RS-232 Communication Port to offer
users more benefits. The download software helps users
monitor UPS inside status. The main features of the UPS
are listed below:

u Microprocessor control guarantees high reliability.

u Equipped with Boost and Buck AVR to stabilize the
input voltage.
u DC Start Function.
u Built-in RS-232 Communication Port.
u Free Software bundled. (Please check UPS
Monitoring Software for detail information).
u Green Power Function for energy saving.
u Auto restart while AC recovery.
u Compact size, Light weight.
u Provides Modem and Phoneline Surge Protection.
u Provide AC Overload Protection.
 +

-
Installation and Operation
Installing the UPS is as easy as following the steps
shown. Be aware of the power Switch must be kept in
the “ON” position, otherwise, the UPS will be
disabled and your equipment will not be protected
during a power failure.
Inspection
1 Remove the UPS from its package and inspect
it for damage that may have occurred during
shipping. If any damage is discovered, re-pack
the unit and return it to the place of purchase.

Placement
2 Install the UPS unit in any protected
environment that provides adequate airflow
around the unit, and is free from excessive
dust, corrosive fumes and conductive
contaminants. Do not operate your UPS in an
environment where the ambient temperature or
humidity is high.

X
On the other hand, place the UPS unit away from the
monitor at least 20cm to avoid interference.

20 cm
 Charging
3 This unit is shipped from the factory with its
internal battery fully charged, however, some
charge may be lost during shipping and the
battery should be recharged prior to use. Plug
the unit into an appropriate power supply and
allow the UPS to charge fully by leaving it
plugged in for at least 8 hours.

¾ 8 hours

Computer Connection
4 Connect one computer-related device into
each of the power receptacles supplied on the
back of the UPS.
 Modem / Phoneline Connection
5 Plug incoming internet line into the “In” socket at
the back of the UPS. Use one more Internet line
cable and plug one end of the Internet line cable
to the “Out” socket at the back of the UPS. Plug
the other end of the modem input socket as
shown below.

Incoming
Internet line

Serial cable Connection

6 To allow for unattended system shutdown for
your operating system, connect the serial
cable as per diagram below.
 Turn On / Off
7 To turn on the UPS, just simply press power
switch. Please Do Not punch it for extended
life of the power switch.

DC Start Function
8 DC Start Function enables UPS to be started
up when AC utility power is not available and
battery is fully charged. Just simply press the
power switch to turn on the UPS.

Green Power Function

9 All these Series are equipped with Green
Power Function. If no load connects to the
UPS, it will automatically shut down in 45
seconds for energy saving while power failure.
The UPS will restart while AC recovery.
 +

-
UPS Monitoring Software
– WinPower –
Every unit is bundled with UPS monitoring software -
WinPower. This is a unique uninterruptible power supply
(UPS) control software that offers you unprecedented
convenience for the control of any UPS.

The software is available for Windows 95 / 98 / NT / 2000,

Novell and Linux. Please follow the steps below to install
the software.

1. Just simply insert bundled CD into CD-ROM drive.

2. Follow the on-screen instruction to install the
software.
3. If no screen shows up after inserting the CD, please
execute setup.exe for initiating installation software.

Note: The software CD supplied along with the UPS has

online help.

Features:
u Saves files before shutdown occurs
u Scheduled system shutdown
u Graphic display of UPS status
u Warning notification via E-mail
u User-friendly interface
u Multi-language versions
 +

-
System Description

Front panel –
1
1. Power Switch
LED Indicators
AC Mode: Green LED on
Battery Mode: Green LED flashing

Back Panel --

1. Output receptacles
2. AC Input
3. Modem / Phoneline Surge Protection
4. Communication Port
5. Circuit Breaker

4
3
2

1 5
 +

-
Specification

MODEL ITON 600 ITON 1000

CAPACITY VA/W 600VA/360W 1000VA/600W
Voltage Range 0-300 VAC
INPUT
Frequency 45-65 Hz (Auto sensing)
Voltage
Voltage Regulation
+/- 10% +/- 5%
(Batt. Mode)
Frequency 50Hz or 60Hz
OUTPUT Frequency Regulation
+/- 1Hz
(Batt. Mode)
Output Waveform Stepped Sinewave
110% for 5 minutes as “Mains”
Overload
mode
12V/7AH 12V/7AH
Battery Type & Number
1Pc 2 Pcs
Backup Time (at a PC
BATTERY 15 min typical 30 min typical
load with monitor)
8 hours to 90% after complete
Recharge Time
discharge
TRANSFER
Typical 4-8 ms
TIME
AC Mode Green Lighting
INDICATOR
Backup Mode Green flashing
Backup Mode Sounding every 10 seconds
Low Battery Sounding every second
AUDIBLE
Overload Sounding every 0.5 seconds
ALARM
Battery Replacement Sounding every 2 seconds
Fault Continuously Sounding
Discharge, overcharge, and
PROTECTION Full Protection
overload protection
Dimension (mm),
330x100x140 369x141x181
PHYSICAL DxWxH
Net Weight 6 kg 13.5 kg
0-40 C, 0-90% relative humidity
Operating Environment
ENVIRONMENT (non-condensing)
Noise Level Less than 40 dB
Support windows
INTERFACE RS-232 95/98/NT/2000/XP,
and Linux
 +

-
Trouble Shooting

Symptom Possible Cause Remedy

No LED display 1. Missing battery 1. Charge battery
on the front panel up to 4 hours
2. battery defect 2. Replace with the
same type of
battery
Alarm buzzer Overload of the UPS Verify that the load
beeps matches the UPS
continuously capability specified in
when AC supply the specs
is normal
When power 1. Overload of the 1. Remove some
failure, back-up UPS non-critical load
time is reduced 2. Battery voltage is 2. Charge battery
too low for 4 hours or more
3. Battery defect due 3. Replace with the
to high temperature same type of
operation battery
environment, or
improper operation
of the battery
Mains normal but 1. Breaker is flicked on 1. Reset the Breaker
LED is flashing 2. Power cord is loose 2. Reconnect the
power cord properly

If any abnormal situations occur that are not listed above,

please call the service engineers immediately.
 +

-
INSTRUCTION
SAVE THESE INSTRUCTION-This manual contains important
instructions for model
ITON 600 Plus that should be followed during installation
and maintenance of the UPS and batteries.
Safety -- Caution!!
u This UPS utilize voltage that may be hazardous. Do not
attempt to disassemble the unit. The unit contains no
user replaceable parts. Only factory service personnel
may perform repairs.
u Internal battery voltage for ITON 600 is 12Vdc and for
ITON 1000 is 24Vdc.
u Connection to any other type of receptacle other than a
two-pole, three-wire grounded receptacle may result in
shock hazard as well as violate local electrical codes.
u In the event of an emergency, press the “OFF” button and
disconnect the power cord from the AC power supply to
properly disable the UPS.
u Do not allow any liquids or any foreign object to enter the
UPS. Do not place beverages or any other liquid-
containing vessels on or near the unit.
u This unit intended for installation in a controlled
environment (temperature controlled, indoor area free of
conductive contaminants). Avoid installing the UPS in
locations where there is standing or running water, or
excessive humidity.
u Do not plug the UPS input into its own output.
u Do not attach a power strip or surge suppressor to the
UPS.
u Do not attach non-computer-related items, such as
medical equipment, life-support equipment, microwave
ovens, or vacuum cleaners to UPS.
u To reduce the risk of overheating the UPS, do not cover
the UPS' cooling vents and avoid exposing the unit to
direct sunlight or installing the unit near heat emitting
appliances such as space heater or furnaces.
u Unplug the UPS prior to cleaning and do not use liquid or
spray detergent.
 Safety – Caution!!
u Do not dispose of batteries in a fire as they may
explode.
u Do not open or mutilate the battery or batteries.
Release electrolyte is harmful to the skin and eyes. It
may be toxic.
u A battery can present a risk of electrical shock and
high short circuit current. The following precautions
should be observed when working on batteries:
1) Remove watches, rings, or other metal objects
from the hands.
2) Use tools with insulated handles.
3) Wear rubber gloves and boots.
4) Do not lay tools or metal parts on top of batteries.
5) Disconnect charging source prior to connecting
or disconnecting batteries terminal.
u Servicing of batteries should be performed or
supervised by personnel knowledgeable of batteries
and the required precautions. Keep unauthorized
personnel away from batteries.
u When replacing batteries, replace with the same
number and type of sealed lead-acid battery.