Scribd
Upload
86 views

EAM108 GAC To WOODWARD (8290) Interface Module

The EAM 108 is an electronic interface module designed to interface a GAC auto sync and load sharing system with a Woodward 8290 engine speed control. It accepts a 5V DC signal and provides a 1.5V DC output signal to the 8290 control. The module requires a 15-32V DC power supply. It has input and output impedances of 60K ohms and 5.8K ohms respectively. Wiring diagrams are provided for connecting the EAM 108 to different Woodward 8290 controller models.

Uploaded by

Imad Hmd
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
86 views

EAM108 GAC To WOODWARD (8290) Interface Module

The EAM 108 is an electronic interface module designed to interface a GAC auto sync and load sharing system with a Woodward 8290 engine speed control. It accepts a 5V DC signal and provides a 1.5V DC output signal to the 8290 control. The module requires a 15-32V DC power supply. It has input and output impedances of 60K ohms and 5.8K ohms respectively. Wiring diagrams are provided for connecting the EAM 108 to different Woodward 8290 controller models.

Uploaded by

Imad Hmd
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Document: Technical Description

Version: 1 EAM108
Status: actual GAC to WOODWARD (8290)
Author: bs Date: 01-12-07 HUEGLI TECH LTD
Engine Interface Module SWITZERLAND
Governing Approved: ro Date: 01-12-07 Tel.:+41-62-916 50 30
Systems File: PC Fax.+41-62-916 50 35
GAC PIB4074 (March 2001) www.huegli-tech.com

EAM108
GAC to WOODWARD (8290) INTERFACE MODULE

Introduction

The EAM 108 is an electronic interface module designed for use with the Woodward 8290
speed control. The typical application is where the GAC auto sync and load sharing system is
to be used with the 8290 engine speed control. The module accepts a nominal 5.0V DC
signal and provides a 1.5V DC signal output to the 8290 control. DC power for the module is
supplied from the 24V DC battery that powers the 8290 control.

Wiring

See Wiring Diagram.

Note: The common battery minus connection between the 8290, EAM 108, and the GAC
auto-sync and load sharing system should be as direct as possible electrically (minimum
voltage difference).

Specifications

Input impedance (Terminals D & A) 60K ohms


Output impedance (Terminals 11 & 12) 5.8K Ohms
Nominal output voltage (Terminals 11 & 12) 1.50V DC
Output voltage range (Terminals 11 & 12) 0-2.6V DC
Nominal input voltage (Terminals D & A) 5.0V DC
Transfer function -1.9 volts/ volt
(without trim pot)
-1.1 volts/ volt (with trim pot)
Temperature range -40° to +85°C
DC supply range (Terminals 1 & 12) 15 to 32V DC
DC supply current (Terminals 1 & 12) 20 mA
Trim Pot (Terminals A, B, & C) use 5K trim potentiometer

W:\DOKUMENTATION 2\Geräte\G A C\Périphérie\E A M\EAM 108\01-12-07-bs-PIB4074-EAM108.doc Page 1 of 2


Document: Technical Description
Version: 1 EAM108
Status: actual GAC to WOODWARD (8290)
Author: bs Date: 01-12-07 HUEGLI TECH LTD
Engine Interface Module SWITZERLAND
Governing Approved: ro Date: 01-12-07 Tel.:+41-62-916 50 30
Systems File: PC Fax.+41-62-916 50 35
GAC PIB4074 (March 2001) www.huegli-tech.com

Wiring Diagram WD164-1 (with WOODWARD 8290-038)

Wiring Diagram WD164-2 (with WOODWARD 8290-184)

W:\DOKUMENTATION 2\Geräte\G A C\Périphérie\E A M\EAM 108\01-12-07-bs-PIB4074-EAM108.doc Page 2 of 2

You might also like