Scribd
Upload
182 views3 pages

ASME B31g Calculation

calculation as per ASME B31.g

Uploaded by

Pasquale Cutri
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
182 views3 pages

ASME B31g Calculation

calculation as per ASME B31.g

Uploaded by

Pasquale Cutri
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 3
Data input for pressure referenced anomaly calculations for a single corrosion pit represented by length, L, and depth, d. The data must be ‘entered in the shaded areas in SI units only. The appropriate conversions are shown to the right of the entered data. Line Name: Rainbow Cadotte-EVI NPS 20” Dig #: Dig RGW 1950 Wheelcount (m): 2134.53 Log Year 2007 Pipe Specifications: SI Units English Units D (mm) = [J 508 "outside diameter 20 inches t(mm) = 7.40 nominal wall thickness 0.291 SMYS (MPa) = _ 359 _ specified minimum yield strength 52068 psi MAOP (kPa) = 7260.00 maximum allowable operating pressure 1052.97 _psi Class Factor= 0.72 Temperature Factor= 1 Defect Information: Lm 140979) measured length of corroded area 551 inches d(mm)= 4.97 _ maximum depth of corroded area 0.078 inches Depth (%)= 27% 27% The greater of Piesg, or MAOP = 7530.52 kPa B31G Maximum Allowable Length = 108.00 mm EXCEEDS ALLOWABLE LENGTH B31G Safe Maximum Pressure = 7391.01 kPa B31G Factor of Safetly= 0.98 0.85dL Area Safe Maximum Pressure = 7809.88 kPa O.85dL Area Factor of Safely= 1.04 ‘Additional Comments = DEFECT EXCEEDS 100mm IN LENGTH Pipe Grade Table Pipe Grade] SMYS (MPa) | SMYS (psi) 25 172 25000 A 207 ‘30000 B 241 '35000 Kaz 288 42000 X46 317 46000 X52, 358 52000 X56 386 56000 X60 a3 ‘60000 X65) 448 ‘65000 X70 482, "70000 X80 551 ‘30000 Conversion Charts 1 0.3048[m 1 = 25.4[mm, 1 = 5280|ft 1 = 7,6093]km “[psi__= 6.8948|kKPa a|MPa_= +1000]kPa ENGINEERING ASSESSMENT REQUIRED ACCEPTABLE, VERIFY WITH ENGINEERING 1.0 ASME B31G-1991 1.1 Calculation of the Maximum Allowable Length of a Corroded Area 1.57 Caleulated factor, equal to 4 for dit < 0.175 Lom 108.00 Maximum Allowable Length of the Corroded Area Evaluation: UNACCEPTABLE 1.2 Calculation of the Maximum Allowable Operating Pressure in Corroded Areas 2.0391 7530.52 Design Pressure 0.72 Class Factor 1 Temperature Factor 7530.52 ‘The greater of the established MAOP or P 7391.01 The safe maximum pressure for the corroded area. 0.98 Evaluation: ACCEPTABLE 2.0 Calculation of the Remaining Strength of Corroded Pipe 2.1 Case 2 - Modified B31G Criterion - 0.85dL Area Folias Factor Constant 521 Folias Facto 2.04 Pa (kPa! 7530.52 Design Pressure Fe 0.72 Class Factor Ts 1 ‘Temperature Factor P(kPa)= 7530.52 ‘The greater of the established MAOP or P Presa (kPa) = 7809.88 The safe maximum pressure for the corroded area, Proust oasa (KPa) = 10847.08 Predicted burst pressure for the corroded area. 0.85dL RPR 1.04 Evaluation: ACCEPTABLE

You might also like