Space Robotics 1

SEMINAR REPORT
(SPACE ROBOTICS)

Submitted to Submitted by:

Mr. Amit Dahiya Yogendra Singh
Mr. Rohit Jain 1514306
(ME)

Seminartopicsonline.com
Space Robotics 2

Chapter -I
INTRODUCTION

Robot is a system with a mechanical body, using computer as its

brain. Integrating the sensors and actuators built into the mechanical body,
the motions are realised with the computer software to execute the desired
task. Robots are more flexible in terms of ability to perform new tasks or to
carry out complex sequence of motion than other categories of automated
manufacturing equipment. Today there is lot of interest in this field and a
separate branch of technology ‘robotics’ has emerged. It is concerned with
all problems of robot design, development and applications. The technology
to substitute or subsidise the manned activities in space is called space
robotics. Various applications of space robots are the inspection of a
defective satellite, its repair, or the construction of a space station and supply
goods to this station and its retrieval etc. With the over lap of knowledge of
kinematics, dynamics and control and progress in fundamental technologies
it is about to become possible to design and develop the advanced robotics
systems. And this will throw open the doors to explore and experience the
universe and bring countless changes for the better in the ways we live.

1.1 AREAS OF APPLICATION

The space robot applications can be classified into the following

four categories
1 In-orbit positioning and assembly: For deployment of satellite and for
assembly of modules to satellite/space station.
2 Operation: For conducting experiments in space lab.
3 Maintenance: For removal and replacement of faulty modules/packages.
4 Resupply: For supply of equipment, materials for experimentation in space
lab and for the resupply of fuel.

Seminartopicsonline.com
Space Robotics 3

The following examples give specific applications under the above

categories

Scientific experimentation:

Conduct experimentation in space labs that may include

 Metallurgical experiments which may be hazardous.
 Astronomical observations.
 Biological experiments.

Assist crew in space station assembly

 Assist in deployment and assembly out side the station.

 Assist crew inside the space station: Routine crew functions inside
the space station and maintaining life support system.

Space servicing functions

 Refueling.
 Replacement of faulty modules.
 Assist jammed mechanism say a solar panel, antenna etc.

Space craft enhancements

 Replace payloads by an upgraded module.

 Attach extra modules in space.

Seminartopicsonline.com
Space Robotics 4

Space tug
 Grab a satellite and effect orbital transfer.
 Efficient transfer of satellites from low earth orbit to geostationary
orbit.

1.2 SPACE SHUTTLE TILE REWATERPROOFING ROBOT

TESSELLATOR

Tessellator

Tessellator is a mobile manipulator system to service the space

shuttle.The method of rewaterproofing for space shuttle orbiters involves
repetitively injecting the extremely hazardous dimethyloxysilane (DMES)
into approximately 15000 bottom tile after each space flight. The field
robotic center at Carneige Mellon University has developed a mobile
manipulating robot, Tessellator for autonomous tile rewaterproofing. Its
automatic process yields tremendous benefit through increased productivity
and safety.

In this project, a 2D-vehicle workspace covering and vehicle routing

problem has been formulated as the Travelling Workstation Problem (TWP).
In the TWP, a workstation is defined as a vehicle which occupies or serves a
Seminartopicsonline.com
Space Robotics 5
certain area and it can travel; a workspace is referred to as a 2D actuation
envelop of manipulator systems or sensory systems which are carried on the
workstation; a work area refers to a whole 2D working zone for a
workstation.
The objective of the TWP is

1 To determine the minimum number of workspaces and their layout, in

which, we should minimize the overlapping among the workspaces and
avoid conflict with obstacles.

2 To determine the optimal route of the workstation movement, in which the

workstation travels over all workspaces within a lowest cost (i.e. routing
time).

The constraints of the problem are

1) The workstation should serve or cover all workareas.

2) The patterns or dimensions of each workspace are the same and
3) There some geographical obstacles or restricted areas.

In the study, heuristic solutions for the TWP, and a case study of
Tessellator has been conducted. It is concluded that the covering strategies,
e.g. decomposition and other layout strategies yield satisfactory solution for
workspace covering, and the cost-saving heuristics can near-optimally solve
the routing problem. The following figure shows a sample solution of TWP
for Tessellator.

Seminartopicsonline.com
Space Robotics 6

Path of tessellator on 2D workspace of space shuttle

1.3 ROBOTS TO REFUEL SATELLITES

The US department of defense is developing an orbital-refueling

robot that could expand the life span of American spy satellites many times
over, new scientists reported. The robotic refueler called an Autonomous
Space Transporter and Robotic Orbiter (ASTRO) could shuttle between
orbiting fuel dumps and satellites according to the Defense Advance
Research Projects Agency. Therefore, life of a satellite would no longer be
limited to the amount of fuel with which it is launched. Spy satellites carry a
small amount of fuel, called hydrazine, which enable them to change
position to scan different parts of the globe or to go into a higher orbit. Such
maneuvering makes a satellites position difficult for an enemy to predict.
But, under the current system, when the fuel runs out, the satellite gradually
falls out of orbit and goes crashing to the earth. In the future the refueler
could also carry out repair works on faulty satellites, provided the have
modular electronic systems that can be fixed by slot in replacements.

Seminartopicsonline.com
Space Robotics 7

Chapter II
SPACE ROBOT—CHALLENGES IN DESIGN AND
TESTING

Robots developed for space applications will be significantly

different from their counter part in ground. Space robots have to satisfy
unique requirements to operate in zero ‘g’ conditions (lack of gravity), in
vacuum and in high thermal gradients, and far away from earth. The
phenomenon of zero gravity effects physical action and mechanism
performance. The vacuum and thermal conditions of space influence
material and sensor performance. The degree of remoteness of the operator
may vary from a few meters to millions of kilometers. The principle effect of
distance is the time delay in command communication and its repercussions
on the action of the arms. The details are discussed below

2.1 ZERO ‘g’ EFFECT ON DESIGN

The gravity free environment in which the space robot operates

possesses both advantages and disadvantages. The mass to be handled by the
manipulator arm is not a constraint in the zero ‘g’ environment. Hence, the
arm and the joints of the space robot need not withstand the forces and the
moment loads due to gravity. This will result in an arm which will be light in
mass. The design of the manipulator arm will be stiffness based and the joint
actuators will be selected based on dynamic torque (i.e.; based on the
acceleration of the arm). The main disadvantage of this type of environment
is the lack of inertial frame. Any motion of the manipulator arm will induce
reaction forces and moment at the base which inturn will disturb the position
and the altitude. The problem of dynamics, control and motion planning for

Seminartopicsonline.com
Space Robotics 8
the space robot is considering the dynamic interactions between the robot
and the base (space shuttle, space station and satellite). Due to the dynamic
interaction, the motion of the space robot can alter the base trajectory and the
robot end effector can miss the desired target due to the motion of the base.
The mutual dependence severely affects the performance of both the robot
and the base, especially, when the mass and moment of inertia of the robot
and the payload are not negligible in comparison to the base. Moreover,
inefficiency in planning and control can considerably risk the success of
space missions. The components in space do not stay in position. They freely
float and are a problem to be picked up. Hence, the components will have to
be properly secured. Also the joints in space do not sag as on earth. Unlike
on earth the position of the arm can be within the band of the backlash at
each joint.

2.2 VACUUM EFFECT AND THERMAL EFFECT

The vacuum in space can create heat transfer problems and mass
loss of the material through evaporation or sublimation. This is to be taken
care by proper selection of materials, lubricants etc., so as to meet the total
mass loss (TML) of <1% and collected volatile condensable matter (CVCM)
of <0.1%. The use of conventional lubricants in bearings is not possible in
this environment. The preferred lubricants are dry lubricants like
bonded/sputtered/ion plated molybdenum disulphide, lead, gold etc. Cold
welding of molecularly similar metal in contact with each other is a
possibility, which is to be avoided by proper selection of materials and dry
lubricants. Some of the subsystem that cannot be exposed to vacuum will
need hermetical sealing. The thermal cycles and large thermal variations will
have to be taken care in design of robot elements. Low temperature can lead
to embrittlement of the material, weaken adhesive bonding and increase
friction in bearings. Large thermal gradients can lead to distortion in
Seminartopicsonline.com
Space Robotics 9
structural elements and jamming of the mechanism. This calls for the proper
selection of the materials whose properties are acceptable in the above
temperature ranges and the selection of suitable protective coatings and
insulation to ensure that the temperature of the system is within allowable
limits.

2.3 OTHER FACTORS

One of the prime requirements of space systems is lightweight and

compactness. The structural material to be used must have high specific
strength and high specific stiffness, to ensure compactness, minimum mass
and high stiffness. The other critical environment to which the space robot
will be subjected to are the dynamic loads during launch. These dynamic
loads are composed of sinusoidal vibrations, random vibrations, acoustic
noise and separation shock spectra.

The electrical and electronic subsystems will have to be space

qualified to take care of the above environmental conditions during launch
and in orbit. The components must be protected against radiation to ensure
proper performance throughout its life in orbit.

The space robots will have to possess a very high degree of

reliability and this is to be achieved right from the design phase of the
system. A failure mode effect and critical analysis (FMECA) is to be carried
out to identify the different failure modes effects and these should be
addressed in the design by
 Choosing proven/reliable designs.
 Having good design margins.
 Have design with redundancy.

Seminartopicsonline.com
Space Robotics 10

2.4 SPACE MODULAR MANIPULATORS

The unique thermal, vacuum and gravitational conditions of space

drive the robot design process towards solutions that are much different from
the typical laboratory robot. JSC's A&R Division is at the forefront of this
design effort with the prototypes being built for the Space Modular
Manipulators (SMM) project. The first SMM joint prototype has completed
its thermal-mechanical-electrical design phase, is now under construction in
the JSC shops, and is scheduled for thermal-vac chamber tests in FY94.

FY93 was the SMM project's first year, initiating the effort with a
MITRE Corporation review of the existing space manipulator design efforts
(RMS and FTS) and interaction with ongoing development teams
(RANGER, JEM, SPDM, STAR and SAT). Below this system level, custom
component vendors for motors, amplifiers, sensors and cables were
investigated to capture the state-of-the-art in space robot design. Four main
design drivers were identified as critical to the development process:

1. Extreme Thermal Conditions;

2. High Reliability Requirements;
3. Dynamic Performance; and
4. Modular Design.

While these design issues are strongly coupled, most robot design
teams have handled them independently, resulting in an iterative process as
each solution impacts the other problems. The SMM design team has sought
a system level approach that will be demonstrated as prototypes, which will
be tested in the JSC thermal-vacuum facilities.

Seminartopicsonline.com
Space Robotics 11

The thermal-vacuum conditions of space are the most dramatic

difference between typical laboratory robot and space manipulator design
requirements. Manufacturing robots operate in climate controlled, \|O(+,-)2K
factory environments, where space manipulators must be designed for \|O(+,)
75K temperature variations with 1500 W/m2 of solar flux. Despite these
environmental extremes, the technology to model and control robot precision
over a wide temperature range can be applied to terrestrial robotic operations
where the extreme precision requirements demand total thermal control, such
as in semiconductor manufacturing and medical robot applications.

Thermal conditions impact reliability by cycling materials and

components, adding to the dynamic loading that causes typical robot fatigue
and inaccuracy. MITRE built a customised thermal analysis model, a failure
analysis model using FEAT, and applied the fault tolerance research funded
by JSC at the University of Texas. The strategy is to layer low level
redundancy in the joint modules with a high level, redundant kinematic
system design, where minor joint failures can be masked and serious failures
result in reconfigured arm operation. In this approach, all four design drivers
were addressed in the selection of the appropriate level of modular design as
a 2-DOF joint module.

The major technical accomplishments for the FY93 SMM project are:
1 Conceptual and detailed design of first joint prototype;
2 Detailed design and fabrication of thermal-vacuum test facility;
3 Custom design of thermal-vac rated motors, bearings, sensors and cables;
and
4 Published two technical papers (R. Ambrose & R. Berka) on robot thermal
design.

Seminartopicsonline.com
Space Robotics 12

Chapter-III
SYSTEM VERIFICATION AND TESTING

The reliability is to be demonstrated by a number of tests

enveloping all the environmental conditions (thermal and vacuum) that the
system will be subjected to. Verification of functions and tests will be
conducted on subsystems, subassemblies and final qualification and
acceptance tests will be done on complete system. The most difficult and the
nearly impossible simulation during testing will be zero ‘g’ simulation.

The commonly used simulations for zero ‘g’ are

1 Flat floor test facility: It simulates zero ‘g’ environments in the horizontal
plane. In this system flat floor concept is based on air bearing sliding over
a large slab of polished granite.
2 Water immersion: Reduced gravity is simulated by totally submerging
the robot under water and testing. This system provides multi degree of
freedom for testing. However, the model has to be water-resistant and have
an overall specific gravity of one. This method is used by astronauts for
extra vehicular activities with robot.
3 Compensation system: Gravitational force is compensated by a passive
and vertical counter system and actively controlled horizontal system. The
vertical system comprises the counter mechanism and a series of pulleys
and cables that provide a constant upward force to balance the weight of
the robot. However, the counter mechanism increases the inertia and the
friction of joints of rotating mechanism.

Seminartopicsonline.com
Space Robotics 13

3.1 PERFORMANCE ASSESSMENT AND CALIBRATION

STRATEGIES FOR SPACE ROBOTS

Predictable safe and cost efficient operation of a robotic device for

space applications can best be achieved by programming it offline during the
preparation for the mission. Computer aided design techniques are used to
assure that the movement of the robot are predictable. A software model of
the robot and its work cell is made and this must be compatible with the
model of the environment in which the robot must perform. Cost efficiency
requirements dictate that a robot be calibrated, after which its performance
must be checked against specified requirements.

Proper use of miniaturized sensing technology is needed to produce

a robot of minimum size, power requirement and consumption and mass.
This often requires minimizing the number and the type of sensors needed,
and maximizing the information (such as position, velocity, and acceleration)
which is gained from each sensor.

The study of methods of assessing the performance of a robot,

choosing its sensors and performing calibration and test, ESA passed a
contract with industry. Results of this work are applicable to any robot
whose kinematics chain needs accurate geometrical modeling.

3.1.1 ROBOT PERFORMANCE ASSESSMENT

The objectives of robot performance assessment are

 To identify the main source of error which perturb the accuracy of
the arm.

Seminartopicsonline.com
Space Robotics 14

 To decide if the arm or the work cell must be calibrated.

 To compare the expected improvement in accuracy in calibration.

The performance of the robot is assessed by making mathematical

model of the characteristics of the error source in each of its sub system such
as the joint, the robot link or its gripper. From these the effects of errors on
the positioning accuracy of end effector (the functioning tip of the robot arm)
can be evaluated.

Error sources are identified by a bottom up analysis, which tale

account of the capabilities of state of the art production technology. For each
robot subsystem error sources are identified and are sorted into three
categories.

 Systematic error which do not vary with time, such as parallelism,

concentricity and link length.
 Pseudo systematic error, which are time variant yet predictable such
as temperature induced effects.
 Random errors, which vary with time and cannot be, predicted such
as encoded noise.

Once the error source have been classified and its magnitude
defined, various statistical methods may be used to evaluate its effects when
they work in combination. Simply adding all the errors, take no account of
their statistical nature and gives an estimate which is safe but unduly
pessimistic; misapplication of statistics can produce an estimate, which is too
optimistic.

Accuracy of some painting mechanism is frequently estimated by

separately eliminating the root mean square value of each of the three error
Seminartopicsonline.com
Space Robotics 15
types identified above and adding them. In the case of AMTS project, all
error sources were considered as statistical variables and a single root mean
square error at the end effector was of interest. The bottom up approach used
to establish the contribution of each power source error source was validated
taking the case of manipulator for which a worst case accuracy of 2.7mm
was predicted. This was very close to its average accuracy of 2mm.

3.1.2 ROBOT CALIBRATION

If the performance prediction has shown that calibration is needed

to compensate for errors, a proper calibration approach is required.

Ideally, all calibration must be done on ground. In orbit calibration

procedures should be limited to crosschecking the validity of model
developed on ground and if necessary correcting for errors such as microslip
page or pressure gradient.

To keep the flight hardware simple, the in orbit calibration should

be achieved using sensors already available in the robot.
Calibration is performed in five steps:

 Modeling, in which a parametric description of the robot is developed,

introducing geometric parameters such as link length and non geometric
parameters such as control parameters.

 Measurement, in which a set of robot poses (position and orientation) and

encoder data are measured using real robot to provide inputs to the
identification test step.

 Identification, which uses the parametric model and the measured data to
determine the optimal set of error parameters.

Seminartopicsonline.com
Space Robotics 16

 Model implementation, which may be done either by updating the root

controller data or by correcting the robot pose with expected standard
deviation of the error.

 Verification, that the improvement in the positioning accuracy of the

robot in all three axes have been achieved.

A method for calibrating each axes independently has been

successfully developed in the frame of the contract. This method uses
independent measurements of motions along each of the three axes.
Advantage of this approach compared to others such as those requiring all
robot joints move simultaneously is that it subdivides the general problem of
robot calibration into a set of problems of lower complexity, thus achieving
good stability and numerical precession. The calibration software is
parametric and is suitable for calibrating any open robot kinematics chain.

3.1.3 PERFORMANCE EVALUATION

As part of a verification procedure, specific performance tests were

carried out on a robot by Krypton under contract to ESA. The first was an
accuracy test in which the robot had to adapt a specified pose and aim at a
point, key characteristics for predictable offline programming. The second
test evaluated the repeatability with which the robot could reach a pose it had
been taught to adopt. This is essential for performing repetitive and routine
tasks.

Finally, the multidirectional pose accuracy was tested to establish

the effect of random errors and to establish the limits of calibration
procedure. The performance of the robot was measured before and after
calibration.

Seminartopicsonline.com
Space Robotics 17

Procedures for calibrating robots on ground and in orbit have been

developed, and the performance of the robotic devices has been successfully
tested. The robot calibration procedure proved to work well resulting in an
improvement in performance by a factor of ten in some cases. The
calibration software is versatile and it can be used to calibrate and evaluate
most kinematics chains ranging from a simple two axes antenna gimbals
mechanism to a ten axes manipulator. These software procedures are now
used by Krypton for applications in most motor industry and elsewhere.

Seminartopicsonline.com
Space Robotics 18

Chapter-IV
STRUCTURE OF SPACE ROBOTS

4.1 DESCRIPTION OF STRUCTURE OF SPACE ROBOT

The proposed robot is of articulated type with 6 degrees of freedom

(DOF). The reason for 6 DOF system rather than one with lesser number of
DOF is that it is not possible to freeze all the information about possible
operations of the payload/racks in 3D space to exclude some DOF of the
robot. Hence, a versatile robot is preferred, as this will not impose any
constraints on the design of the laboratory payload/racks and provide
flexibility in the operation of the robot. A system with more than six DOF
can be provided redundancies and can be used to overcome obstacles.
However, the complexities in analysis and control for this configuration
become multifold.

The robot consists of two arms i.e. an upper arm and a lower arm.
The upper arm is fixed to the base and has rotational DOF about pitch and
yaw axis. The lower arm is connected to the upper arm by a rotary joint
about the pitch axis. These 3 DOF enable positioning of the end effector at
any required point in the work space. A three-roll wrist mechanism at the
end of the lower arm is used to orient the end effector about any axis. An end
effector connected to the wrist performs the required functions of the hand.
Motors through a drive circuit drive the joint of the arm and wrist. Angular
encoders at each joint control the motion about each axis. The end effector is
driven by a motor and a pressure sensor/strain gauges on the fingers are used
to control the grasping force on the job.

Seminartopicsonline.com
Space Robotics 19

4.2 DISCRIPTION OF SUBSYSTEMS

The main subsystems in the development of the manipulator arm are

 Joints
 Arm
 Wrist
 Gripper

4.2.1 JOINTS

A joint permits relative motion between two links of a robot. Two

types of joints are
1 Roll joint – rotational axis is identical with the axis of the fully extended
arm.
2 Pitch joint – rotational axis is perpendicular to the axis of the extended
arm and hence rotation angle is limited.

The main requirements for the joints are to have near zero backlash,
high stiffness and low friction. In view of the limitations on the volume to be
occupied by the arm within the workspace, the joints are to be highly
compact and hence they are integrated to the arm structure. To ensure a high
stiffness of the joint the actuator, reduction gear unit and angular encoders
are integrated into the joint.

Seminartopicsonline.com
Space Robotics 20
Each joint consists of

 Pancake type DC torque motors (rare earth magnet type) which have
advantage over other types of motors with respect to size, weight,
response time and high torque to inertia ratio.

 Harmonic gear drive used for torque amplification/speed reduction.

These gear drives have near zero backlash, can obtain high gear
ratios in one stage only and have high efficiency.

 Electromagnetically actuated friction brakes, which prevent

unintentional movements to the arms. This is specifically required
when the gear drive is not self-locking. In space environment, where
the gravity loads are absent (zero ‘g’ environment) brakes will help
to improve the stability of the joint actuator control system. i.e. the
brake can be applied as soon as the joint velocity is less than the
threshold value.

 Electro optical angular encoders at each axis to sense the position of

the end of the arm. Space qualified lubricants like molybdenum
disulphide (bonded film/sputtered), lead, gold etc. will be used for
the gear drives and for the ball bearings.

4.2.2 ROBOT ARMS

The simplest arm is the pick and place type. These may be used to
assemble parts or fit them into clamp or fixture. This is possible due to high
accuracy attainable in robot arm. It is possible to hold the part securely after
picking up and in such a way that the position and the orientation remains
accurately known with respect to the arm. Robot arms can manipulate
objects having complicated shapes and fragile in nature.

Seminartopicsonline.com
Space Robotics 21

4.2.3 WRIST

Robot arm comprises of grippers and wrist. Wrist is attached to the

robot arm and has three DOF (pitch, yaw, and roll). Wrist possesses the
ability to deform in response to the forces and the torques and return to
equilibrium position after the deflecting forces are removed.

4.2.4 GRIPPER

Gripper is attached to the wrist of the manipulator to accomplish the

desired task. Its design depends on the shape and size of the part to be held.

Seminartopicsonline.com
Space Robotics 22

Chapter-V
OPERATION

5.1 SPACE SHUTTLE ROBOT ARM (SHUTTLE REMOTE

MANIPULATOR SYSTEM)

5.1.1 USE OF SHUTTLE ROBOT ARM

The Shuttle's robot arm is used for various purposes.

 Satellite deployment and retrieval

 Construction of International Space Station

 Transport an EVA crew member at the end of the arm and provide a
scaffold to him or her. (An EVA crew member moves inside the cargo bay
in co-operation with the support crew inside the Shuttle.)

 Survey the outside of the Space Shuttle with a TV camera attached to the
elbow or the wrist of the robot arm.

Seminartopicsonline.com
Space Robotics 23
Shuttle robot arm observed from the deck

5.1.2 ROBOT ARM OPERATION MODE

SRMS is operated inside the Space Shuttle cabin. The operation is

performed from the aft flight deck (AFD), right behind the cockpit; either
through the window or by watching two TV monitors. To control the SRMS,
the operator uses the translational hand controller (THC) with his or her left
hand and manipulates the rotational hand controller (RHC) with his or her
right hand.

THC RHC

5.1.3 HOW SPACE SHUTTLE ROBOT ARM GRASPS OBJECT?

How does the Space Shuttle robot arm grasp objects? Many people
might think of human hand or magic hand, but its mechanism is as follows.
At the end of the robot arm is a cylinder called the end effector. Inside this
cylinder equipped three wires that are used to grasp objects. The object to be
grasped needs to have a stick-shaped projection called a grapple fixture. The
three wires in the cylinder fix this grapple fixture at the centre of the
cylinder.
However, a sight is needed to acquire the grapple fixture while manipulating
a robot arm as long as 45 feet. The grapple fixture has a target mark, and a

Seminartopicsonline.com
Space Robotics 24
rod is mounted vertically on this mark. The robot arm operator monitors the
TV image of the mark and the rod, and operates the robot arm to approach
the target while keeping the rod standing upright to the robot arm. If the
angular balance between the rod and the robot arm is lost, that can
immediately be detected through the TV image.

End effector and grapple fixture

Robot arm’s payload acquiring sequence

5.2 FREE FLYING SPACE ROBOTS

The figure below shows an example of a free flying space robot. It

is called ETS VII (engineering test satellite VII). It was designed by NASDA
and launched in November 1997. In a free flying space robot a robot arm is

Seminartopicsonline.com
Space Robotics 25
attached to the satellite base. There is a very specific control problem. When
the robot arm moves, it disturbs the altitude of the satellite base.
This is not desirable because,
 The satellite may start rotating in an uncontrollable way.
 The antenna communication link may be interrupted.

One of the research objectives is to design robot arm trajectories and

to control the arm motion in such a way that the satellite base remains
undisturbed or that the disturbance will be minimum.

Seminartopicsonline.com
Space Robotics 26

Free flying space robots

5.3 SPACE STATION MOUNTED ROBOTS

The international space station (ISS) is a sophisticated structural

assembly. There will be several robot arms which will help astronauts in
performing a variety of tasks.

Seminartopicsonline.com
Space Robotics 27
JEMRMS

The figure shows a part of ISS including the Japanese Experimental

Module (JEM). A long manipulator arm can be seen. The arm is called
JEMRMS (JEM Remote Manipulating System). A small manipulator arm
called SPDM (Special purpose dexterous Manipulator) can be attached to
JEMRMS to improve the accuracy of operation.

SPDM

5.4 SPACE ROBOT TELEOPERATION

Space robotics is one of the important technologies in space

developments. Especially, it is highly desired to develop a completely
autonomous robot, which can work without any aid of the astronauts.
However, with the present state of technologies, it is not possible to develop
a complete autonomous space robot. Therefore, the teleoperation
technologies for the robots with high levels of autonomy become very
Seminartopicsonline.com
Space Robotics 28
important. Currently, the technologies where an operator teleoperates a space
robot from within a spacecraft are already in practical use, like the capture of
a satellite with the shuttle arm. However, the number of astronauts in space
is limited, and it is not possible to achieve rapid progresses in space
developments with the teleoperation from within the spacecraft. For this
reason, it has become highly desired to develop the technologies for the
teleoperation of space robots from the ground in the future space missions.

CONCLUSION

In the future, robotics will make it possible for billions of people to

have lives of leisure instead of the current preoccupation with material
needs. There are hundreds of millions who are now fascinated by space but
do not have the means to explore it. For them space robotics will throw open
the door to explore and experience the universe.

Seminartopicsonline.com
Space Robotics 29

ABSTRACT

Robot is a mechanical body with the brain of a computer.

Integrating the sensors and the actuators and with the help of the computers,
we can use it to perform the desired tasks. Robot can do hazardous jobs and
can reach places where it’s difficult for human beings to reach. Robots,
which substitute the manned activities in space, are known as space robots.
The interest in this field led to the development of new branch of technology
called space robotics. Through this paper, I intend to discuss about the
applications, environmental condition, testing and structure of space robots.

Seminartopicsonline.com
Space Robotics 30

CONTENTS

1. INTRODUCTION 1

2. SPACE ROBOT—CHALLENGES IN DESIGN AND

TESTING 6

3. SYSTEM VERIFICATION AND TESTING 11

4. STRUCTURE OF SPACE ROBOTS 17

5. OPERATION 21

6. CONCLUSION 27

Seminartopicsonline.com