WWW.ANITE.

COM/NEMO

NEMO OUTDOOR 7.90

DEVICE CONFIGURATION GUIDE

DOCUMENT NUMBER
NNNNNNNNN ISSUE N

© Anite 2016
 DEVICE CONFIGURATION GUIDE

Copyright

The information contained in this document is confidential and no part of it may be copied or
reproduced in any form without the written consent of Anite Network Testing. Additionally, this
document is not to be passed to or discussed with third parties without the prior written permission
of Anite Network Testing.

Anite’s products are subject to continual development and specifications may change. Users of
Anite’s products and documentation should exercise their own independent judgement to evaluate
the suitability of Anite’s products and documentation for their particular use. Anite does not accept
any liability arising from the application or use of the product or this documentation.

All reasonable care has been made to ensure that this document is accurate. If you have any
comments on this document, or would like details of any Anite products, services or equipment,
please contact us through the Anite website.

Page 2
 DEVICE CONFIGURATION GUIDE

CONTENTS

1 INTRODUCTION ................................................................................................. 6
1.1 Device autodetection .................................................................................. 7
1.2 Manual configuration of data connection ....................................................... 7
1.3 Adding devices with Nemo Media Router ..................................................... 11
1.4 Disabling driver signature verification on 64-Bit Windows 8.1 or 10 ................ 14

2 APPLE IPHONE 6/6S ......................................................................................... 17

3 APPLE IPHONE 5 .............................................................................................. 19

4 BANDRICH BANDLUXE C320 .............................................................................. 20

5 BITTIUM TOUGH MOBILE .................................................................................. 22

6 BLACKBERRY TORCH 9810 ................................................................................ 24

7 CELLIENT R40 ................................................................................................. 27

7.1 Setting up the packet data connection (Windows Mobile Broadband Connection)
30

8 DATANG DTM8101/DTM8120/ LEADCORE LC8130E .............................................. 31

9 HTC 10M 33

10 HTC ONE XL .................................................................................................... 41

11 HTC ONE M8.................................................................................................... 46

12 HUAWEI P9 ..................................................................................................... 53

13 IF THE DEVICE CONNECTING FAILS, CHECK THAT YOU HAVE SELECTED THE CORRECT
COM PORTS AND TRY AGAIN.HUAWEI ASCEND MATE 7 ............................................ 55

14 HUAWEI E3276S-150/861 ................................................................................. 58

15 HUAWEI ASCEND P2 ......................................................................................... 60

16 HUAWEI E180/E169/E182E/E1820 /E270+/E367/E392U-12/E372U-8 USB MODEM .. 63

17 HUAWEI E392U-12 ........................................................................................... 65

17.1 Changing TCP/IP Properties ....................................................................... 66

18 HUAWEI C7600 ................................................................................................ 68

19 HUAWEI E398 .................................................................................................. 71

19.1 Changing TCP/IP Properties ....................................................................... 71

Page 3
 DEVICE CONFIGURATION GUIDE

20 KODIAK PTT .................................................................................................... 73

20.1 Driver installation ..................................................................................... 73
20.2 Pairing the phone with the laptop ............................................................... 75
20.3 Configure and connect Kodiak PTT client via Bluetooth .................................. 77
20.4 Adding Kodiak PTT device in Nemo Outdoor ................................................. 79

21 LG C676/C680/VX8300/U900/ KU950/KX206/KX256/KF700/ TU550 ....................... 81

22 LG VX8350/VX8360 .......................................................................................... 85

23 LG P930, G2 .................................................................................................... 88

24 LG G4 90

25 LG P500H 91

26 MOTOROLA MOTO X PURE ................................................................................. 92

27 NETGEAR AIRCARD 340U .................................................................................. 95

28 NETGEAR AIRCARD 782S, 790S, 810S ................................................................ 97

29 NOKIA LUMIA 920 (RM-821).............................................................................. 99

30 NOKIA 6120/6121/6720(US)/ C5/C5-00.2/C5-03(US)/C5-04/C7-00/E7-00/N85(US)/

N95(US)/N96(US)/N97(US)................................................................................. 101

31 NOKIA 500 104

32 NOVATEL OVATION MC930D/MC990D/MC996D/ MC998D/MC545 ......................... 106

33 NOVATEL OVATION MC727/MC760 ................................................................... 108

34 NSN USB-LTE 7210 (ALTAIR)........................................................................... 110

35 ONDA MT689DC ............................................................................................. 114

36 PANTECH UM175 ............................................................................................ 116

37 PANTECH UML290 .......................................................................................... 119

38 SAMSUNG GALAXY CORE (SM-G386F) .............................................................. 122

39 SAMSUNG GALAXY S4 (GT-I9505, SGH-I337, SPH-L720, SGH-M919, SCH-R970, SGH-

M919N, SGH-I337M), GALAXY S4 ACTIVE (GT-I9295), GALAXY S II (GT-I9210) ........ 124

40 SAMSUNG GALAXY S II SKYROCKET, GALAXY S II HD LTE (SHV-E120S KOREAN

VERSION) 126

41 SAMSUNG GALAXY S III (SGH-I747, SGH-T999, SCH-I535, SPH-L710), GALAXY

RUGBY, GALAXY S4 MINI (GT-I9195, SPH-L520), GALAXY S4 4G+ (GT-I9506), GALAXY
NOTE 3 (SM-N9005, SM-N900T, SM-N9008V, SM-N9007), GALAXY NOTE 3 LITE (SM-
N7509V), GALAXY NOTE 4 (SM-N910F, SM-N910G, SM-N910T), GALAXY S5 (ALL
VARIANTS) 128

Page 4
 DEVICE CONFIGURATION GUIDE

42 SAMSUNG GALAXY S6, GALAXY NOTE 5, GALAXY S6 EDGE+ ............................... 131

43 SAMSUNG GALAXY S7, GALAXY S7 EDGE .......................................................... 133

44 SAMSUNG GALAXY S III (GT-I9305), GALAXY II NOTE (GT-N7105) ...................... 135

45 SIERRA WIRELESS AIRCARD 306/307/308/309/310U/ 312U/313U/320U/330U, SIERRA

COMPASS 889, SIPTUNE SM215 .......................................................................... 138

46 SIERRA WIRELESS COMPASS 597 .................................................................... 141

47 SONY XPERIA Z3 (D6603, D6653), Z5 (E6653) .................................................. 143

47.1 Configuring Sony Xperia Z3 (D6603, D6653) for use with Nemo Invex II Handset
Isolation Module ............................................................................................ 144

48 SONY ERICSSON XPERIA ARC S ....................................................................... 149

49 SONY XPERIA X PERFORMANCE F8131, F8132, X F5121, XZ F8331 ...................... 157

50 ZTE MF820T/MF820D ..................................................................................... 160

51 ZTE MF668A .................................................................................................. 161

52 ZTE MF683 162

53 ZTE MF880 163

54 ZTE TU25 164

55 APPLICATION TESTER ..................................................................................... 166

56 TECHNICAL SUPPORT ..................................................................................... 167

56.1 User Club .............................................................................................. 167
56.2 Nemo Support Portal .............................................................................. 167
56.3 Phone and email support ......................................................................... 167

Page 5
 DEVICE CONFIGURATION GUIDE

1 INTRODUCTION

The purpose of this document is to give step-by-step instructions for setting up test devices for data
testing with Nemo tools.

 Please note that the devices below have been removed from the current document.
Configuration instructions for these devices can be found in the Dial-up Networking Setup
Guide version 7.10.

 Audiovox PC5750/Pantech PX-500

 Huawei EC169/EC169C USB Modem

 LG G7/G13/G17

 LG VL600

 LG U900/KU950

 LG L1000

 Merlin U530/U740/X950D

 Motorola V3x/V3XX/V3XXUS/V9/V9US

 Nokia 6230i, N80, 3500

 Option GlobeTrotter 3G+/GT MAX 7.2 Ready/HSDPA 7.2/Express 7.2

 Option iCon 452

 Option GlobeSurfer iCON 7.2 USB modem

 Qualcomm TM6250/6275/6280/7200/8200/ MDM9200/MDM9600

 Samsung Z105/Z107/Z140/Z500/Z560/Z720/ZV10/ZX20/A707/G800/P920/P940/SHG-
T639/SGH-U800/SHG-U900, Droid Charge

 Sierra Wireless Aircard 850/860

 Sierra Wireless Aircard 880/881

 Sierra Wireless Compass 885

 Zapp Telemodem Z020

Page 6
 DEVICE CONFIGURATION GUIDE

1.1 Device autodetection

From Nemo Outdoor 5.60 onwards, it is possible to use autodetection to add devices to Nemo
Outdoor. It is no longer necessary to manually configure a data connection. Once a device is
connected to the Nemo Outdoor computer and the device driver is installed, it can be added fully
automatically to Nemo Outdoor using the Autodetect button. Nemo Outdoor will automatically
detect the device trace and modem ports and assign a suitable data connection.

Autodetection works with all Nemo Outdoor test terminals verified by Anite Network Testing. In
some cases it is possible that the terminal is not recognized and the autodetection does not work. If
this happens, manually select the correct trace and modem ports. Then select Automatic in the PS
data connection field and click Apply. If the automatic data connection detection does not work,
please see instructions below.

1.2 Manual configuration of data connection

1. Select Start | Control Panel | Network and Internet. Select Network and Sharing Center |
Set up a new connection or network. Select Set up a dial-up connection, and click Next.

Page 7
 DEVICE CONFIGURATION GUIDE

2. Select the correct terminal from the list and click Next.
With Nokia terminals, select the item with the highest number, e.g., in this case #3.

3. In the Telephone Number field, enter *99# (#777 for CDMA terminals). In the
Connection name field type, for example, Nokia Dial-up connection. Select Allow other
people to use this connection. Click Connect.

Page 8
 DEVICE CONFIGURATION GUIDE

4. Click on Skip in the Connecting to xxx dial-up connection dialog.

5. Click Close.

6. Go to Control Panel | Network and Internet | Network and Sharing Center, and select
Connect to a network. Right-click on the Terminal Dial-up Connection, and select Properties.

Page 9
 DEVICE CONFIGURATION GUIDE

7. In the Networking tab, deselect the Internet Protocol Version 6 (TCP/IPv6) item and
select Internet Protocol Version 4 (TCP/IPv4). Click OK.

 Steps 8 and 9 apply only to Nokia terminals.

8. Go to Device Manager (Start | Settings | Control Panel | System and Security |

Device Manager), and double-click on Modems. Right-click on the #3 item on the list and
click Properties.

Page 10
 DEVICE CONFIGURATION GUIDE

9. Select the Advanced tab, and type in atz in the Extra initialization commands field, and
click on OK.

10. See the following chapters for terminal-specific instructions on adding terminals to Nemo
Outdoor.

1.3 Adding devices with Nemo Media Router

When the Nemo Outdoor test devices have Nemo Media Router installed, there are some additional
settings that need to be selected. Usually these devices can be added to Nemo Outdoor using
autodetection in which case Nemo Outdoor will automatically detect the correct ports and data
connections. If autodetection does not work for some reason, follow the instructions below.

 When NMR is used, check that the mobile data setting is enabled from the device. Pull
down the menu from the top of the device screen and check that the mobile data setting
is activated.

1. First follow the device-specific instructions in this document for installing the device drivers.

2. After the drivers have been installed, connect the device to the Nemo Outdoor laptop and
add the device in Nemo Outdoor.

3. In the Device Configuration dialog, select the correct ports for Trace port and Modem port.
See the device-specific instructions in this document for more detailed information.

Page 11
 DEVICE CONFIGURATION GUIDE

4. Select Automatic in the Nemo Media Router and PS data connection fields. Click OK.

5. If the Nemo Media Router field is disabled, check that USB tethering has been activated. Go
to Windows Network and Sharing Center and click Change adapter settings.

Page 12
 DEVICE CONFIGURATION GUIDE

6. In the Network Connections dialog, check that there is a Local Area Connection made
with the test device (e.g. Samsung) and that the connection is enabled. If the connection is
disabled, right-click on the connection and select Enable.

7. If there is no local area connection for your test device, disconnect the USB cable, reboot
the test device, and then reconnect the device to the laptop. Also check that the NMR
application is set to Outdoor mode.

Page 13
 DEVICE CONFIGURATION GUIDE

1.4 Disabling driver signature verification on 64-Bit Windows 8.1

or 10
To disable driver signature verification, go to the Troubleshooting options from the boot manager.
Hold down the SHIFT key and click Restart from the power options menu (on Windows 8 that is
under Charms or on the login screen, and in Windows 10 on the Start Menu).

When the computer restarts, select the Troubleshoot option.

Select Advanced options.

Page 14
 DEVICE CONFIGURATION GUIDE

Select Startup Settings.

Select Restart.

Page 15
 DEVICE CONFIGURATION GUIDE

When the computer starts up again, you will be given a list of startup settings that you can change.
Press the F7 key to select the Disable driver signature enforcement setting.

The computer will restart and you will now be able to install unsigned drivers.

Page 16
 DEVICE CONFIGURATION GUIDE

2 APPLE IPHONE 6/6S

 These instructions apply to the Apple iPhone carrier build phones provided by Apple.

1. Install iTunes.

2. Connect the iPhone to the control PC using the iPhone’s own cable.

3. Allow iPhone to connect to the control PC (iTunes will ask this, so if it is not started
automatically, you need to start it manually) and select Trust from the iPhone.

4. Check that there is an IP address in NMR.

5. If there is no IP address, switch on Personal Hotspot from the iPhone (switch off WiFi
before this). Select Bluetooth and USB Only.

Page 17
 DEVICE CONFIGURATION GUIDE

6. Go to Device Manager. Under Network Adapters you should see the Apple Mobile
Device Ethernet item.

7. Start Nemo Outdoor. Click the Autodetect button and start the device in Offline mode.

8. Go to the Nemo Outdoor Device Configuration dialog and select Automatic for the Nemo
Media Router option.

 When Nemo Media Router is set to <Automatic>, Voice quality must be disabled because
it is not supported by NMR/iPhone.

9. Click Apply. Start the device in Online mode.

Page 18
 DEVICE CONFIGURATION GUIDE

3 APPLE IPHONE 5

Apple iPhone 5 can be connected with Nemo Outdoor using the application tester handler.

1. Install iTunes on your computer. iTunes can be downloaded from

http://www.apple.com/itunes/download. Start iTunes.

2. On the iPhone 5 device, select Settings | Personal Hotspot and turn on the Personal
Hotspot.

3. Connect the USB connectivity cable to your PC. Device drivers are installed automatically.

4. Go to Nemo Outdoor and select Measurement | Add New Device | Phone | Application
Tester.

5. Leave the Trace Port and Modem Port fields empty.

6. Select <LAN> as the PS data connection. Click OK.

 Activate a packet session manually before running scripts.

 Note that when testing with iPhone 5, all other connections (WLAN, Ethernet cable, etc.)
need to be disconnected.

Page 19
 DEVICE CONFIGURATION GUIDE

4 BANDRICH BANDLUXE C320

1. Plug in the USB device in one of your PC’s USB ports. The drivers are automatically
installed, and Windows automatically detects the device.

2. Select English in the Choose Setup Language dialog.

3. Click on Next in the Welcome dialog that appears.

4. Select I accept the terms in the license agreement in the License Agreement dialog,
and click Next.

5. Select a destination folder and click Next.

6. Click Install to start the installation and click Finish to finish the installation.

7. Close the BandLuxe software that appears, as it will not be required in the following steps.

Page 20
 DEVICE CONFIGURATION GUIDE

8. Go to Start | Control Panel | Hardware and Sound | Device Manager. Under Modems you
should be able to see the BandLuxe 3.5G Modem, under Network adapters you should see
the BandLuxe 3.5G Ethernet Adapter, and under Ports the BandLuxe Adapter Control
Interface (COMxx) and BandLuxe AT CMD Interface (COMxx) items.

9. In Nemo Outdoor Device Configuration dialog, select the COM port number assigned to
the BandLuxe Adapter Control Interface item in the Trace Port field. Select the COM
port number assigned to the BandLuxe 3.5G Modem item (right-click the item and select
Properties) in the Modem Port field.

Page 21
 DEVICE CONFIGURATION GUIDE

5 BITTIUM TOUGH MOBILE

 Do not connect the USB connectivity cable to your PC until the driver installation is
complete.

1. Insert the Nemo Outdoor installation DVD and browse to the driver folder (e.g. Nemo
Outdoor\Nemo Outdoor xx\Drivers\Bittium\Tough Mobile). Run the Qualcomm installer
QUD.WIN.1.1 Installer-10037.3.zip.

2. Select WWAN-DHCP as the Setup Type. Click Next.

3. If a Windows Security message appears, select Install.

4. After the Qualcomm driver installation is finished, install the Bittium drivers. Run the
ToughMobileInstaller.exe. If a Windows Security message appears, select Install. After
installation, restart the laptop.

5. When the installation is complete, connect the device to the PC.

Page 22
 DEVICE CONFIGURATION GUIDE

6. Go to Device Manager. Under Ports you should see the ToughMobile HS-USB Diagnostics
item. Under Modems you should see the ToughMobile HS-USB Android Modem item.

7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

8. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to ToughMobile HS-USB Diagnostics.

 Modem port: Select the COM port number assigned to ToughMobile HS-USB Android
Modem.

 PS data connection: NDIS

9. Click Apply.

10. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 23
 DEVICE CONFIGURATION GUIDE

6 BLACKBERRY TORCH 9810

 Please note that currently the driver can be installed on 32-bit Windows only.

 Install the device drivers. The file is located on the Nemo Outdoor USB flash drive.
Browse the file manually and double-click the 610_b038_multilanguage file. The package
will self-extract.

1. The Blackberry Desktop Software application is launched. Select the installation language
and click OK.

2. If the installer requests to install the Microsoft Visual C++ 2008 Redistributable file, click
Install.

3. Click Next to begin the Blackberry Desktop SW installation.

4. Select your country or region and click Next.

5. Accept the license agreement and click Next.

6. Select the installation folder and click Next and Install.

7. Wait until the installation is complete and click Finish.

8. Close the Blackberry software that appears, as it will not be required in the following steps.

Page 24
 DEVICE CONFIGURATION GUIDE

9. Go to Device Manager. Under Modems you should see the Standard Modem item and under
Ports two RIM Virtual Serial Port v2 items.

10. Connect the device USB cable to the device and to the Nemo Outdoor laptop. Select USB
Drive from the device screen.

11. Start Nemo Outdoor. Autodetection does not work with the Blackberry device so add the
device manually (Add New Device | Phone | Qualcomm).

Page 25
 DEVICE CONFIGURATION GUIDE

12. In the Device Configuration dialog, select the COM port with the bigger number assigned
to the RIM Virtual Serial Port v2 item in the Trace Port field. Select the COM port with
the smaller number in the Modem Port field. Select Automatic in the PS data connection
field.

Page 26
 DEVICE CONFIGURATION GUIDE

7 CELLIENT R40

 Please note that this driver is an unsigned driver. Driver signature verification on 64-Bit
Windows 8.1 or 10 needs to be disabled. Please follow the instructions in chapter 1.4
Disabling driver signature verification on 64-Bit Windows 8.1 or 10.

1. Extract the Cellient R40 drivers.zip file and run the Setup.exe file.

2. When the installation is finished, connect the USB cable.

3. In Windows Device Manager, you will see several Cellient devices under Other devices.

4. Right-click on the first device and select Update Driver Software.

5. Select Browse my computer for driver software.

Page 27
 DEVICE CONFIGURATION GUIDE

6. Click Browse and browse to the Cellient R40 drivers\driver files folder. Click OK and Next.

7. During the installation, a security message will appear. Select Install this driver software
anyway to continue the installation.

8. When the installation is complete, click Close.

Page 28
 DEVICE CONFIGURATION GUIDE

9. Repeat steps 4-8 for all Cellient devices under Other devices. One of the devices may not
get drivers (“Windows was unable to install your Cellient”), but that does not affect the
device behavior with Nemo Outdoor.

10. After updating the driver software for all the Cellient devices, go to Device Manager. You
should see the following:

 Under Modems:

o Qualcomm HS-USB Android Modem 9025

 Under Network adapters:

o Qualcomm HS-USB WWAN Adapter 9025

 Under Ports:

o Qualcomm HS-USB Diagnostics 9025

o Qualcomm HS-USB NMEA 9025

Page 29
 DEVICE CONFIGURATION GUIDE

7.1 Setting up the packet data connection (Windows Mobile

Broadband Connection)
1. After you have successfully installed the Cellient device drivers and you have a SIM card
inserted in the device, you can continue to enable and activate the packet data connection.
This device uses Windows Mobile Broadband connection method to establish the internet
connectivity from Windows.

2. From the Windows System Tray (bottom right corner of the Windows Desktop), you can
open the available networks. You should see an available connection under “Mobile
Broadband Connections”.

3. Click on the available connection and press Connect. If you are using Windows 8, select the
Connect Automatically option before pressing Connect. In Windows 7, you will need to
select the Connect automatically except when roaming or Always connect automatically
option after pressing Connect.

Page 30
 DEVICE CONFIGURATION GUIDE

8 DATANG DTM8101/DTM8120/
LEADCORE LC8130E

 Do not connect the connectivity cable to your PC until the driver installation is complete.

1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse the
file manually and double-click the USB2VCOM_driver_x.xx.xx file (x is the latest driver
version).

2. Select Uninstall old version first if installed, and click Install in the Leadcore Technology
DTM8100 Series Driver Installer dialog.

3. In the VCOM Number field you need to select 3 ports for each test terminal. Since the driver
is installed only once, select the number of COM ports according to how many Leadcore
terminals you intend to use with Nemo Outdoor. Hence, if you want to connect two
Leadcore terminals with Nemo Outdoor, select at least 6 in the VCOM Number field. Click
Exit when the installation is done.

4. After the driver installation is finished, Windows may restart your computer but it is not
required.

5. After your computer has restarted, connect the connectivity cable to the mobile and the
other end to the computer’s USB port. Windows will detect the new hardware automatically
and start the installation. The step is repeated several times until all new hardware is
added.

6. In the Welcome page, select No, not this time and click Next.

7. Select Install the software automatically (Recommended) and click Next.

Page 31
 DEVICE CONFIGURATION GUIDE

8. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware
Installation dialog if it appears. You may need to repeat steps 6, 7 and 8 several times
until the installation process is finished.

9. After installation, go to Device Manager. Select Start | Control Panel open the Hardware
and Sound tab and click the Device Manager button.

10. You should be able to see three Datang Mobile modems under Modems, and three Datang
Mobile items under Ports.

11. Start Nemo Outdoor. Select View | Windows Device Manager. From the Device Manager
you will find the COM port numbers needed in the next steps.

12. Select Measurement | Add New Device. In the New Device dialog, click Phones and
select the terminal. Click Next.

13. In the Device Manager click on Ports. Select the COM port number assigned to the
Leadcore Technology DTM8100 Modem #2 item In the Trace Port field in the Device
Configuration dialog. Select the COM port number assigned to the Leadcore Technology
DTM8100 Modem #3 item in the Modem Port field.

14. In the Device Configuration dialog, select <Automatic> as the PS data connection
(see page 7). Click Apply.

15. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 32
 DEVICE CONFIGURATION GUIDE

9 HTC 10M

1. Connect the device to the laptop. Select Charge only on the phone.

1. Go to Device Manager. You should see the following items:

 Modems: HTC USB Modem

 Network adapters: HTC Remote NDIS based Device

 Ports: HTC Diagnostic Interface

2. You can now jump to step 36.

3. If these items are not visible, you will need to update the drivers. See the following step.

Page 33
 DEVICE CONFIGURATION GUIDE

4. Under Other devices you will see HTC DIAG item.

5. Right-click on the HTC DIAG item and select Update Driver Software.

Page 34
 DEVICE CONFIGURATION GUIDE

6. In the Update Driver SW – HTC DIAG dialog, select Browse my computer…

7. Select Let me pick from a list…

Page 35
 DEVICE CONFIGURATION GUIDE

8. Select Show All Devices and click Next.

9. Click Have Disk.

Page 36
 DEVICE CONFIGURATION GUIDE

10. On the Nemo Outdoor product package, browse to folder Drivers\Qualcomm\HTC_10M

\DIAG and select the correct subfolder based on your operating system, e.g. \Win7_x86.
Click OK.

11. Click Next.

12. If the Windows Security dialog appears, click Install this driver anyway. The driver will
be installed. Click Close after the installation is finished.

Page 37
 DEVICE CONFIGURATION GUIDE

13. The HTC DIAG item has disappeared and a new item HTC Diagnostic Interface appears
under Ports.

14. Now repeat the driver software update process for the HTC Modem and RmNet items.
Ignore all Windows warnings. The steps are otherwise the same but the driver files are
located in different folders:

 HTC Modem: Drivers\Qualcomm\HTC_10M\Modem

 RmNet: Drivers\Qualcomm\HTC_10M\QMI

Page 38
 DEVICE CONFIGURATION GUIDE

15. After you have updated all drivers, go to Device Manager. You should see the following
items:

 Modems: HTC USB Modem

 Network adapters: HTC Remote NDIS based Device

 Ports: HTC Diagnostic Interface

16. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

17. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to the HTC Diagnostic Interface.

 Modem port: Select the COM port number assigned to HTC USB Modem

 PS data connection: HTC Remote NDIS based Device

18. Click Apply.

19. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 39
 DEVICE CONFIGURATION GUIDE

Page 40
 DEVICE CONFIGURATION GUIDE

10 HTC ONE XL

2. Connect the device to the laptop. Select Charge only on the phone.

3. Go to Device Manager. Under Other devices you should see the HTC DIAG, HTC Modem,
and RmNet items.

4. Right-click on the HTC DIAG item and select Update Driver Software.

Page 41
 DEVICE CONFIGURATION GUIDE

5. In the Update Driver SW – HTC DIAG dialog, select Browse my computer…

6. Select Let me pick from a list…

Page 42
 DEVICE CONFIGURATION GUIDE

7. Select Show All Devices and click Next.

8. Click Have Disk.

9. On the Nemo Outdoor product package, browse to folder

Drivers\Qualcomm\HTC_One_XL\DIAG and select the correct subfolder based on your
operating system, e.g. \Win7_x86. Click OK.

Page 43
 DEVICE CONFIGURATION GUIDE

10. Click Next.

11. If the Windows Security dialog appears, click Install this driver anyway. The driver will
be installed. Click Close after the installation is finished.

12. The HTC DIAG item has disappeared and a new item HTC Diagnostic Interface appears
under Ports.

13. Now repeat the driver software update process for the HTC Modem and RmNet items.
Ignore all Windows warnings. The steps are otherwise the same but the driver files are
located in different folders:

Page 44
 DEVICE CONFIGURATION GUIDE

 HTC Modem: Drivers\Qualcomm\HTC_One_XL\Modem

 RmNet: Drivers\Qualcomm\HTC_One_XL\QMI

After you have updated all drivers, go to Device Manager. You should see the following
items:

 Modems: HTC USB Modem

 Network adapters: HTC Ethernet Adapter

 Ports: HTC Diagnostic Interface

14. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

15. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to the HTC Diagnostic Interface.

 Modem port: Select the COM port number assigned to HTC USB Modem

 PS data connection: NDIS

16. Click Apply.

17. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 45
 DEVICE CONFIGURATION GUIDE

11 HTC ONE M8

20. Connect the device to the laptop. Select Charge only on the phone.

21. Go to Device Manager. You should see the following items:

 Modems: HTC USB Modem

 Network adapters: HTC Remote NDIS based Device

 Ports: HTC Diagnostic Interface

22. You can now jump to step 36.

23. If these items are not visible, you will need to update the drivers. See the following step.

Page 46
 DEVICE CONFIGURATION GUIDE

24. Under Other devices you will see the HTC DIAG, HTC Modem, and RmNet items.

25. Right-click on the HTC DIAG item and select Update Driver Software.

Page 47
 DEVICE CONFIGURATION GUIDE

26. In the Update Driver SW – HTC DIAG dialog, select Browse my computer…

27. Select Let me pick from a list…

Page 48
 DEVICE CONFIGURATION GUIDE

28. Select Show All Devices and click Next.

29. Click Have Disk.

Page 49
 DEVICE CONFIGURATION GUIDE

30. On the Nemo Outdoor product package, browse to folder

Drivers\Qualcomm\HTC_One_XL\DIAG and select the correct subfolder based on your
operating system, e.g. \Win7_x86. Click OK.

31. Click Next.

32. If the Windows Security dialog appears, click Install this driver anyway. The driver will
be installed. Click Close after the installation is finished.

Page 50
 DEVICE CONFIGURATION GUIDE

33. The HTC DIAG item has disappeared and a new item HTC Diagnostic Interface appears
under Ports.

34. Now repeat the driver software update process for the HTC Modem and RmNet items.
Ignore all Windows warnings. The steps are otherwise the same but the driver files are
located in different folders:

 HTC Modem: Drivers\Qualcomm\HTC_One_XL\Modem

 RmNet: Drivers\Qualcomm\HTC_One_XL\QMI

Page 51
 DEVICE CONFIGURATION GUIDE

35. After you have updated all drivers, go to Device Manager. You should see the following
items:

 Modems: HTC USB Modem

 Network adapters: HTC Remote NDIS based Device

 Ports: HTC Diagnostic Interface

36. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

37. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to the HTC Diagnostic Interface.

 Modem port: Select the COM port number assigned to HTC USB Modem

 PS data connection: HTC Remote NDIS based Device

38. Click Apply.

39. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 52
 DEVICE CONFIGURATION GUIDE

12 HUAWEI P9

1. In case there are previously installed Huawei drivers on the computer, first, uninstall any old
drivers.

2. Make sure that HUA (HiSilicon UE Agent) / Hisi agent is not switched on, so that it will not occupy
serial ports.

3. Go to Start | Network Connections. Right-click on Remote NDIS based Internet Sharing

Device (Ethernet) and Select Properties. Confirm selection by clicking Yes. Go to
Networking page and disable Ipv6 in the network adapter settings. Note that unless the
device’s USB port is changed, disabling Ipv6 only needs to be done once.

4. Connect the device to your computer’s USB port. Depending on the phone model NMR may be
available for the phone. If, however, NMR is not available, USB tethering must be enabled
manually by switching on USB tethering from the phone’s UI. The procedure for getting USB
tethering and trace port working together is as follows:

1. Turn on USB tethering from the phone (trace and modem ports will disappear)
2. Switch on trace ports by using the HiSilicon Android app. (background settings -> USB
port settings -> USB ports setting -> Balong debug mode. When device ask to reboot, just
cancel with back button.)
3. Turn on USB tethering again (now USB tethering and ports are both enabled)

5. Use Autodetection to add device to Nemo Outdoor. Steps 6 and 7 only need to be followed if
autodetection is not used.

6. In Nemo Outdoor, go to Add phone | HiSilicon Kirin. In Device Configuration dialog select
the port assigned to HUAWEI Mobile Connect – GPS Interface in the Trace Port field. In the
Modem port field select the port assigned to Huawei Mobile Connect - Modem. You can find the
right port and modem in Device Manager:

Page 53
 DEVICE CONFIGURATION GUIDE

7. In the Device Configuration dialog, select <NDIS> as the PS data connection. Click Apply.

Page 54
 DEVICE CONFIGURATION GUIDE

13 IF THE DEVICE CONNECTING FAILS,

CHECK THAT YOU HAVE SELECTED
THE CORRECT COM PORTS AND TRY
AGAIN.HUAWEI ASCEND MATE 7

1. Connect the device to your computer’s USB port.

2. Install the HiSilicon UE Agent 7.2.5 from folder Nemo Outdoor xxx\Drivers\HiSilicon
Mate7\Hua_V7.2.5. Follow the instructions in the setup wizard to finish the installation.

3. Install device drivers from folder Drivers\HiSilicon Mate7\28. 2.10.2014 HiSilicon P7, Honor
6 & Mate 7 drivers. Run the DriverSetup file.

4. Make the following settings on your device.

5. Dial *#*#2846579#*#*. This will open up the Testing menu. Select ProjectMenu.

6. Select Background setting.

Page 55
 DEVICE CONFIGURATION GUIDE

7. Select Usb ports setting.

8. Select USB Ports Setting.

9. Select Balong Debug mode.

Page 56
 DEVICE CONFIGURATION GUIDE

10. Open the Device Manager. You should see the Huawei Mobile Connect – 3G Application
Interface and Huawei Mobile Connect – Application Interface items under Ports.

11. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the HiSilicon item. Click Next.

12. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to Huawei Mobile Connect – 3G
Application Interface

 Modem port: Select the COM port number assigned to Huawei Mobile Connect –
Application Interface

13. In the Device Configuration dialog, select <NDIS>. Click Apply.

14. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 57
 DEVICE CONFIGURATION GUIDE

14 HUAWEI E3276S-150/861

1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and start the installation. Click Run AutoRun.exe and follow the instructions on
the screen.

2. The Telenor Mobile Partner software starts up. Please note that the appearance of the Mobile
Partner software varies depending on operator etc. Close the program.

3. After installation, go to Device Manager. Select Start | Control Panel, open the Hardware tab
and click the Device Manager button.

4. You should see the Huawei Mobile Connect – 3G Application Interface item and the Huawei
Mobile Connect – Application Interface items under Ports.

5. Install the Hisi UE Agent to default installation folder. The file is located on the Nemo Outdoor
USB flash drive. Browse to folder …\Nemo Outdoor x.x\Drivers\HiSilicon\ Hisi UE Agent B211
and run the Hisi UE Agent Balong V700R001C50B211.exe file.

 NOTE! After the installation is finished, Hua.exe file must be located under folder C:\Hisi
UE Agent\bin\hua.exe.

6. Install Huut- Huawei UE Update Tool 1.3 (Nemo Outdoor x.x\Drivers\HiSilicon\Huut-V1.3.) This
is necessary if no diagnostics have been activated yet in UE. Activation can only be performed
by Huawei.

Page 58
 DEVICE CONFIGURATION GUIDE

7. Start Huut- Huawei Update Tool and generate the file. Send the file to Huawei.

8. Update file (key) provided by Huawei with Huut- Update tool. Update file is generated based on
IMEI of UE.

9. The device can be added manually. Select Measurement | Add New Device. In the New Device
dialog, click Phones and select the HiSilicon item. Click Next.

10. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei
Mobile Connect – 3G Application Interface item in the Trace Port field in the Device
Configuration dialog. Select the COM port number assigned to the Huawei Mobile Connect –
Application Interface item in the Modem Port field.

11. In the Device Configuration dialog, select <NDIS> as the PS data connection. Click Apply.

12. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 59
 DEVICE CONFIGURATION GUIDE

15 HUAWEI ASCEND P2

1. First, install device drivers from folder Nemo Outdoor xxx\Drivers\HiSilicon\Huawei Ascend
P2-6011. This will install the Mobile Broadband on your computer. Follow the instructions in
the setup wizard to finish the installation.

2. Next install the HiSilicon UE Agent from folder Nemo Outdoor xxx\Drivers\HiSilicon\Hisi UE
Agent xxx. Follow the instructions in the setup wizard to finish the installation.

3. Make the following setting on your device:

4. Dial *#*#2846579#*#*. This will open up the Testing menu. Select ProjectMenu.

5. Select Background setting

Page 60
 DEVICE CONFIGURATION GUIDE

6. Select Usb port setting

7. Select USB mode switch

8. Select Switch to CP modem

 Note that USB mode must be switched to CP mode every time the device is rebooted.

9. Connect the device to your computer’s USB port. Windows will detect and install the new
hardware automatically.

10. If the Mobile Broadband application starts, close the program.

11. After installation, go to Device Manager.

Page 61
 DEVICE CONFIGURATION GUIDE

12. You should see the Huawei Mobile Connect – Network Adapter item under Network
Adapters and the Huawei Mobile Connect – 3G Application Interface and Huawei
Mobile Connect – Application Interface items under Ports.

13. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the HiSilicon item. Click Next.

14. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to Huawei Mobile Connect – 3G
Application Interface

 Modem port: Select the COM port number assigned to Huawei Mobile Connect –
Application Interface

15. In the Device Configuration dialog, select <NDIS>. Click Apply.

16. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 62
 DEVICE CONFIGURATION GUIDE

16 HUAWEI E180/E169/E182E/E1820
/E270+/E367/E392U-12/E372U-8
USB MODEM

 Applies to all 3G and 4G Huawei USB modems. The Huawei Connection Manager starts up
every time the device is plugged in and it must be closed in order to be able to use the
device with Nemo Outdoor. As a workaround, the Connection Manager .exe file can be
renamed. A reinstall warning will be displayed when device is plugged in but this can be
ignored.

1. Plug in the USB device in one of your PC’s USB ports. The drivers are automatically
installed, and Windows automatically detects the device.

2. Next, ignore and close the Vodafone or Mobile Partner application that appears. It should
not be on while connecting the device with Nemo Outdoor later on.

3. You may need to restart the computer for the installation to take effect.

4. Go to Start | Control Panel | Phone and Modem Options | Modems. You should see
the Huawei Mobile Connect – 3G Modem item with its associated COM port number in the
list.

 Please note that with some Huawei E392U-12 devices the Huawei Mobile Connect – 3G
Modem item does not appear. If this happens, please follow the instructions in chapter
Huawei E392u-12.

5. Start Nemo Outdoor. Select View | Windows Device Manager. From the Device Manager
you will find the COM port numbers needed in the next steps.

6. Select Measurement | Add New Device. In the New Device dialog, click Phones and
select the Qualcomm item. Click Next.

Page 63
 DEVICE CONFIGURATION GUIDE

7. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei
Mobile Connect – 3G Application Interface item in the Trace Port field in the Device
Configuration dialog. Select the COM port number attached to the Huawei Mobile
Connect – 3G Modem item in the Modem Port field.

8. In the Device Configuration dialog, select <Automatic> as the PS data connection

(see page 7). Click Apply.

9. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 64
 DEVICE CONFIGURATION GUIDE

17 HUAWEI E392U-12

 Please note that with some Huawei E392U-12 devices the Huawei Mobile Connect – 3G
Modem item does not appear. If this happens, please follow the instructions below.

 The Huawei Connection Manager starts up every time the device is plugged in and it must
be closed in order to be able to use the device with Nemo Outdoor. As a workaround, the
Connection Manager .exe file can be renamed. A reinstall warning will be displayed when
device is plugged in but this can be ignored.

1. Plug in the USB device in one of your PC’s USB ports. The drivers are automatically
installed, and Windows automatically detects the device.

2. Next, ignore and close the Vodafone or Mobile Partner application that appears. It should
not be on while connecting the device with Nemo Outdoor later on.

3. You may need to restart the computer for the installation to take effect.

4. Start Nemo Outdoor. Select View | Windows Device Manager. In the Device Manager,
you should see the following two items and their COM port numbers under Ports: Huawei
Mobile Connect – Application Interface and Huawei Mobile Connect – PC UI
Interface.

5. Select Measurement | Add New Device. In the New Device dialog, click Phones and
select the Qualcomm item. Click Next.

6. In the Device Manager click on Ports. Select the COM ports as follows:

 Trace port: Huawei Mobile Connect – Application Interface

 Modem port: Huawei Mobile Connect – PC UI Interface

7. In the Device Configuration dialog, select <Automatic> as the PS data connection

(see page 7). Click Apply.

Page 65
 DEVICE CONFIGURATION GUIDE

8. If the device connecting fails, check that you have selected the correct COM ports and try
again.

17.1 Changing TCP/IP Properties

 Applies to all 3G and 4G Huawei USB modems with Nemo Outdoor 6.30 and older
versions. Before measurements can be done with Nemo Outdoor, the Internet protocol
properties must be manually changed to automatic mode. This must be done always after
the modem is disconnected/reconnected and also if the device stops responding during
measurements.

 Windows 7:
1. Plug in the Huawei device.

2. Go to Start | Control Panel | Network and Internet | Network and Sharing Center.

3. Click on Change adapter settings.

4. Right-click on Mobile Broadband Connection and select Properties.

Page 66
 DEVICE CONFIGURATION GUIDE

5. In the Mobile Broadband Connection Properties dialog, select Internet Protocol Version 4
(TCP/IPv4) and click on Properties.

6. Select Obtain an IP address automatically and Obtain DNS server address automatically.
Click OK and OK.

Page 67
 DEVICE CONFIGURATION GUIDE

18 HUAWEI C7600

 Do not connect the USB data cable to your PC until the driver installation is complete.

1. The data cable driver is located on the Nemo Outdoor USB flash drive. Browse to folder
D:\Drivers\Drivers for Qualcomm Based Devices\Huawei C7600 and run the driver .exe file.

2. Click Install in the DriverInstall Setup: Installation Options dialog.

3. Click Close in the DriverInstall Setup: Completed dialog.

Page 68
 DEVICE CONFIGURATION GUIDE

4. After the installation has finished, connect the USB connectivity cable to your phone, and
the other end of the cable to your computer’s USB port. Windows will detect the new
hardware automatically and start the installation.

5. In the Welcome page, select No, not this time and click Next.

6. Select Install the software automatically (Recommended) and click Next.

7. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware
Installation dialog if it appears. You may need to repeat steps 5, 6 and 7 several times
until the installation process is finished. Click Finish to exit the wizard.

8. After installation, go to Device Manager. Select Start | Control Panel, open the Hardware
tab and click the Device Manager button.

Page 69
 DEVICE CONFIGURATION GUIDE

9. You should see the HUAWEI CDMA Handset – Modem item under Ports.

10. Start Nemo Outdoor. Select View | Windows Device Manager. From the Device Manager
you will find the COM port numbers needed in the next steps.

11. Select Measurement | Add New Device. In the New Device dialog, click Phones and
select the Qualcomm item. Click Next.

12. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei
CDMA Handset – Application Interface item In the Trace Port field in the Device
Configuration dialog. Select the COM port number attached to the Huawei CDMA
Handset - Modem item in the Modem Port field.

13. In the Device Configuration dialog, select <Automatic> as the PS data connection
(see page 7). Click Apply.

14. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 70
 DEVICE CONFIGURATION GUIDE

19 HUAWEI E398

 Applies to all 3G and 4G Huawei USB modems. The Huawei Connection Manager starts up
every time the device is plugged in and it must be closed in order to be able to use the
device with Nemo Outdoor. As a workaround, the Connection Manager .exe file can be
renamed. A reinstall warning will be displayed when device is plugged in but this can be
ignored.

1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and start the installation. Click Run AutoRun.exe and follow the instructions
on the screen.

2. The Telenor Mobile Partner software starts up. Close the program.

3. After installation, go to Device Manager. Select Start | Control Panel, open the Hardware
tab and click the Device Manager button.

4. You should see the Huawei Mobile Connect – Modem item under Modems and the Huawei
Mobile Connect – Application Interface and Huawei Mobile Connect – PC UI Interface items
under Ports.

5. Start Nemo Outdoor. Select View | Windows Device Manager. From the Device Manager
you will find the COM port numbers needed in the next steps.

6. Select Measurement | Add New Device. In the New Device dialog, click Phones and
select the Qualcomm item. Click Next.

7. In the Device Manager click on Ports. Select the COM port number assigned to the Huawei
Mobile Connect – PC UI Interface item in the Trace Port field in the Device
Configuration dialog. Select the COM port number assigned to the Huawei Mobile
Connect - Modem item in the Modem Port field.

8. In the Device Configuration dialog, select <NDIS> as the PS data connection. Click Apply.

9. If the device connecting fails, check that you have selected the correct COM ports and try
again.

19.1 Changing TCP/IP Properties

 Applies to all 3G and 4G Huawei USB modems with Nemo Outdoor 6.30 and older
versions. Before measurements can be done with Nemo Outdoor, the Internet protocol
properties must be manually changed to automatic mode. This must be done always after
the modem is disconnected/reconnected and also if the device stops responding during
measurements.

 Windows 7:
1. Plug in the Huawei device.

2. Go to Start | Control Panel | Network and Internet | Network and Sharing Center.

Page 71
 DEVICE CONFIGURATION GUIDE

3. Click on Change adapter settings.

4. Right-click on Mobile Broadband Connection and select Properties.

5. In the Mobile Broadband Connection Properties dialog, select Internet Protocol Version 4
(TCP/IPv4) and click on Properties.

6. Select Obtain an IP address automatically and Obtain DNS server address automatically.
Click OK and OK.

Page 72
 DEVICE CONFIGURATION GUIDE

20 KODIAK PTT

20.1 Driver installation

1. The first step is to install drivers for the Bluetooth adapter. The driver file (IOGEAR
Bluetooth 4.0 USB Micro Adapter GBU521 Driver Win Vista 7 v6.5.1.2700) can be
downloaded from the Nemo User Club (nemouserclub.anite.com) or from
http://www.iogear.com/support/dm/driver/GBU521#display

2. Run the Autorun.exe file.

3. Wait until the driver has been installed.

4. Agree to install the Bluetooth service.

5. Plug in the USB to Bluetooth module to your Nemo Outdoor laptop when prompted.

6. When installation is ready, press Finish.

7. Go to Control Panel | Hardware and Sound | Devices and Printers. You should see the
BCM920702 Bluetooth 4.0 device.

Page 73
 DEVICE CONFIGURATION GUIDE

8. Right click the Bluetooth device and select Bluetooth settings.

9. Select the Show the Bluetooth icon in the notification area option.

Page 74
 DEVICE CONFIGURATION GUIDE

20.2 Pairing the phone with the laptop

1. Check the computer name from the Device Manager.

2. Enable Bluetooth on your Kodiak PTT phone.

3. Enable your device visibility.

4. Select Add a Device from the Bluetooth menu on your laptop and follow the wizard to add
the phone.

Page 75
 DEVICE CONFIGURATION GUIDE

5. Confirm the pairing code and click Next.

6. You should now see your phone as a device in the Devices and Printers view.

Page 76
 DEVICE CONFIGURATION GUIDE

20.3 Configure and connect Kodiak PTT client via Bluetooth

1. Launch the Kodiak PTT client on the phone.

2. On your laptop, go to Control Panel - Hardware and Sound, right-click the device (your
phone) and select Properties.

3. On the Services page, select the Serial port (SPP) ‘KodiakPoCApplication’ option.

4. Click OK and a Bluetooth serial port will be installed.

Page 77
 DEVICE CONFIGURATION GUIDE

5. Go back to the PTT1 Properties, Services page. You should now see a COM port assigned for
the Serial port.

6. You should also see a COM port under Ports in Device Manager.

Page 78
 DEVICE CONFIGURATION GUIDE

20.4 Adding Kodiak PTT device in Nemo Outdoor

1. Device can be added using either the terminal specific handler or the Application Tester
handler. These steps will show the usage with the Application Tester handler.

2. Launch Nemo Outdoor.

3. Add a new device (Application Tester) and click Next.

4. In the Kodiak PTT port field, select the COM port that was assigned for the Standard
Serial over Bluetooth link item (check from Device Manager, Ports).

5. When using the Application Tester handler, there is no need to configure the Trace or
Modem ports. Also data connections can be “Not Used” if only Kodiak testing will be
performed.

Page 79
 DEVICE CONFIGURATION GUIDE

6. Press OK to add the device. You are now ready to start the measurements.

Page 80
 DEVICE CONFIGURATION GUIDE

21 LG C676/C680/VX8300/U900/
KU950/KX206/KX256/KF700/ TU550

 Do not connect the USB connectivity cable to your PC until the connectivity cable driver
installation is complete.

 The LG KF700 USB driver conflicts with the LG USB driver for CDMA terminals. If both
drivers are installed on the same computer, the terminals are not detected.

1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. With LG
C676, C680, and KX 206, browse to folder D:\Drivers\Qualcomm CDMA drivers, and run the
LGUSBModemDriver.exe file. With the LG VX8300 terminal, browse to folder
D:\Drivers\Qualcomm US Specific Softwares, and run the LGUSB Driver_Eng__Ver_x.x.exe
file (x is the latest driver version). With U900/KU950/KX206/KX256/KF700/TU550, browse
to folder D:\Drivers\Qualcomm Specific Softwares\LG USB Driver v.3.35.0.600\Driver and
run the Setup.exe file.

2. On the InstallShield Wizard welcome page click Next.

3. If a Software Installation warning appears, click Continue Anyway. You may need to
repeat this step two or three times.

4. Click OK in the Information dialog.

5. Next, connect one end of the connectivity cable shipped with the mobile phone to the
mobile, and the other end to the computer’s USB port. Windows will detect the new
hardware automatically and start the installation.

6. In the Welcome page, select No, not this time and click Next.

Page 81
 DEVICE CONFIGURATION GUIDE

7. Select Install the software automatically (Recommended) and click Next.

8. Click Continue Anyway or Yes in the Hardware Installation or Digital Signature Not
Found dialog if it appears. You may need to repeat steps 5, 6 and 7 several times until the
installation process is finished.

9. The USB driver has now been installed. Click Finish.

10. You need to restart your computer for the installation process to take effect. Click Yes in
the System Settings Change dialog.

11. After installation, select Start | Settings | Control Panel | Phone and Modem Options,
then open the Modem tab.

Page 82
 DEVICE CONFIGURATION GUIDE

12. Under the Modem item you should see the created LGE CDMA USB Modem and the port
attached to it, in this example COM 17.

Page 83
 DEVICE CONFIGURATION GUIDE

13. Go to Device Manager by selecting Start | Control panel | Hardware and Sound. In the
Device Manager you should see the LGE CDMA USB Serial Port item. Leave the Device
Manager open as you will find there the COM port numbers needed in the next steps.

14. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

15. In the Device Manager click on Ports. Select the COM port number assigned to the LGE
CDMA USB Serial Port item in the Trace Port field in the Device Configuration dialog.
Leave the Modem Port field empty.

16. In the Device Configuration dialog, select <Automatic> as the PS data connection. Click
Apply.

17. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 84
 DEVICE CONFIGURATION GUIDE

22 LG VX8350/VX8360

1. Insert the Nemo Outdoor USB flash drive in the USB port. Browse to folder
D:\Drivers\Qualcomm Specific Softwares\LGUSBModemDriver.exe.

2. Double-click the .zip file. Click Unzip. This will extract files to a folder in your C drive. Click
Close.

3. Switch on the mobile. Connect one end of the USB data cable to the terminal and the other
end to an empty USB port on your PC.

4. Windows will automatically detect the new hardware. Select No, not this time in the
Found New Hardware Wizard and click Next.

5. Select Install from a list or specific location and click Next.

Page 85
 DEVICE CONFIGURATION GUIDE

6. Select Include this location in the search and browse to folder D:\Nemo Drivers\LG
VX8x00 driver on the Nemo Outdoor USB flash drive. Click Next.

7. The driver files are installed. Steps 2, 3, and 4 are repeated several times until the new
hardware is ready to be used.

Page 86
 DEVICE CONFIGURATION GUIDE

8. When the installation is complete, check from the Device Manager that the installation was
successful. Under Modems you should see the LGE CDMA USB Modem, and under Ports
you should see the LGE CDMA USB Serial Port item. Leave the Device Manager open as
you will find there the COM port numbers needed in the next steps.

9. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

10. In the Device Manager click on Ports. Select the COM port number assigned to the LGE
CDMA USB Serial Port item in the Trace Port field in the Device Configuration dialog.
Leave the Modem Port field empty.

11. In the Device Configuration dialog, select <Automatic> as the PS data connection (see
page 7). Click Apply.

12. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 87
 DEVICE CONFIGURATION GUIDE

23 LG P930, G2

 Do not plug in the device before installation!

1. Run the LGUnitedMobileDriver_S4981MAN36AP22_ML_WHQL_Ver_3.6.exe file found on the

Nemo Outdoor USB flash drive to start the installation wizard.

2. First select the setup language and click Next.

3. Click Next in the Welcome dialog. The driver will be installed. Click OK in the driver
installed successfully message.

4. Plug in the device. Enable USB tethering from the mobile (Menu – Settings - Wireless &
networks - Tethering & portable hotspot, select USB tethering).

 Please note that if the USB connection is disconnected (i.e. device is unplugged), the USB
tethering must be re-enabled on the phone in order to use the data connection.

5. Windows will automatically detect the new hardware. Select No, not this time and click
Next.

6. Select Install the software automatically and click Next.

7. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware Installation
dialog if it appears. You may need to repeat steps 6, 7 and 8 several times until the
installation process is finished.

Page 88
 DEVICE CONFIGURATION GUIDE

8. After installation, go to Device Manager. You should see the LGE AndroidNet USB Modem
item under Modems and LGE AndroidNet For Diagnostics Port and LGE AndroidNet
USB Serial Port items under Ports. Leave the Device Manager open as you will find there
the COM port numbers needed in the next steps.

9. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

10. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port:
For LG P930: Select the COM port number assigned to the LGE AndroidNet For
Diagnostics Port.
For LG G2: Select the COM port number assigned to the LGE AndroidNet USB Serial
Port.

 Modem port: Select the COM port number assigned to LGE AndroidNet USB Modem.

 PS data connection: Automatic

 When using the device in LTE, do not issue manual packet session commands. If the
connection needs to be disconnected, use Radio On/Off commands.

 If you are making voice calls, issue an "ATS0=1" AT command to enable the incoming
calls. This must be done every time the phone is restarted.

Page 89
 DEVICE CONFIGURATION GUIDE

24 LG G4

 Do not plug in the device before drivers are installed!

1. Browse to folder Drivers\Qualcomm based devices\LG\LG G4 on the Nemo Outdoor USB

flash drive.

2. Run the Qualcomm USB Host Driver, Setup.exe file to start the installation wizard. If the
Windows Security dialog appears, click Run.

3. After the device driver installation is finished, connect the terminal to the computer with a
USB cable. Windows will automatically detect the new hardware and install drivers. Wait
until the installation process is finished.

4. After installation, go to Device Manager. You should see the Qualcomm HS-USB Android
Modem item under Modems and Qualcomm HS-USB Diagnostics item under Ports.

5. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

6. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to Qualcomm HS-USB Diagnostics.

 Modem port: Select the COM port number assigned to Qualcomm HS-USB Android
Modem.

 PS data connection: NDIS

7. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 90
 DEVICE CONFIGURATION GUIDE

25 LG P500H

 Do not plug in the device before drivers are installed!

1. Browse to folder Drivers\Qualcomm based devices\LG WCDMA terminals\LG P500H on the

Nemo Outdoor USB flash drive.

2. Run the LGAndroidPlatformDriver_WHQL_ML_Ver_1.2_All_Win7.exe file to start the

installation wizard. If the Windows Security dialog appears, click Run.

3. After the device driver installation is finished, connect the terminal to the computer with a
USB cable. Windows will automatically detect the new hardware and install drivers. Wait
until the installation process is finished.

4. After installation, go to Device Manager. You should see the LGE Android Platform USB
Modem item under Modems and LGE Android Platform USB Serial Port item under
Ports.

5. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

6. Select the port assigned to LGE Android Platform USB Serial Port in the Trace Port field
in the Device Configuration dialog. Select the port assigned to LGE Android Platform USB
Modem in the Modem Port field.

7. In the Device Configuration dialog, select <Automatic> as the PS data connection (see
page 7). Click Apply.

8. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 91
 DEVICE CONFIGURATION GUIDE

26 MOTOROLA MOTO X PURE

 Please note that this driver is an unsigned driver. Driver signature verification on 64-Bit
Windows 8.1 or 10 needs to be disabled. Please follow the instructions in chapter 1.4
Disabling driver signature verification on 64-Bit Windows 8.1 or 10.

1. Extract the “Moto XT1575 drivers.zip” file on the desktop or other easy-to-remember
location.

2. Run Setup.exe and follow instructions on the screen to finish the installation.

3. Connect the USB cable from the device to your computer.

4. In Windows Device Manager, you should see several devices under “Other devices”.

5. Right-click on the first device and select Update Driver Software.

6. Select Browse my computer for driver software.

Page 92
 DEVICE CONFIGURATION GUIDE

7. Click Browse, go to the Moto XT1575 drivers\driver files folder and click OK and Next.

8. A security pop-up will appear. Select Install this driver software anyway to continue the
installation.

9. Click Close when the driver installation is finished.

Page 93
 DEVICE CONFIGURATION GUIDE

10. Repeat steps 5-9 for all of the devices under “Other devices” (at the beginning there should
be “diag”, “modem” and “nmea”). After installation, go to Device Manager. You should see
the following items:

Under Modems:

 Qualcomm HS-USB Android Modem 9026

Under Network adapters:

 Remote NDIS based Internet Sharing Device

Under Ports:

 Qualcomm HS-USB Diagnostics 9026 (COMxx)

 Qualcomm HS-USB NMEA 9026 (COMxx)

Page 94
 DEVICE CONFIGURATION GUIDE

27 NETGEAR AIRCARD 340U

1. Plug in the USB device in one of your PC’s USB ports. The drivers are automatically
installed, and Windows automatically detects the device.

2. Go to Network adapter settings and select Never connect automatically in the

Autoconnect field.

Page 95
 DEVICE CONFIGURATION GUIDE

3. After installation, go to Device Manager. You should see the following items:
Modems: Sierra Wireless WWAN Modem
Ports: Sierra Wireless DM Port

4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

5. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to Sierra Wireless DM Port

 Modem port: Select the COM port number assigned to Sierra Wireless WWAN Modem

6. In the Device Configuration dialog, select <NDIS> as the PS data connection. Click
Apply.

7. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 96
 DEVICE CONFIGURATION GUIDE

28 NETGEAR AIRCARD 782S, 790S,

810S

 Do not connect the USB connectivity cable to your PC until the driver installation is
complete.

1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse to
folder Nemo Outdoor 7.7.1.14\Drivers\Qualcomm\Netgear\[your device model] and run the
.exe file.

2. Follow the instructions in the installation wizard to finish the driver installation.

3. Connect the connectivity cable to the mobile and the other end to the computer’s USB port.
Windows will detect the new hardware automatically and install the necessary drivers.

4. After installation, go to Device Manager. You should see the following items:
Modems: Netgear WWAN Modem
Ports: Netgear DM Port

5. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

6. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to Netgear DM Port

Page 97
 DEVICE CONFIGURATION GUIDE

 Modem port: Select the COM port number assigned to Netgear WWAN Modem

7. In the Device Configuration dialog, select <NDIS> as the PS data connection. Click
Apply.

8. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 98
 DEVICE CONFIGURATION GUIDE

29 NOKIA LUMIA 920 (RM-821)

 Do not connect the USB connectivity cable to your PC until the driver installation is
complete.

1. First, uninstall any existing Qualcomm drivers.

2. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse to
folder Nemo Outdoor\Nemo Outdoor x.x\Drivers\Qualcomm\Nokia\Lumia 920 RM-821\USB
Host Driver 1.00.12\72 and run the setup.exe file.

3. Click Next in the Welcome dialog. Select I accept… in the License Agreement dialog and
click Next.

4. Click Install and finally Finish.

5. After the connectivity cable driver installation is finished, Windows may restart your
computer but it is not required.

6. After your computer has restarted, connect the connectivity cable to the mobile and the
other end to the computer’s USB port. Windows will detect the new hardware automatically
and start the installation. The step is repeated several times until all new hardware is
added.

 Please note that with newer Nokia devices the Wizard may not appear at all and instead
the installation is performed automatically.

7. In the Welcome page, select No, not this time and click Next.

8. Select Install the software automatically (Recommended) and click Next.

9. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware
Installation dialog if it appears. You may need to repeat steps 8, 9, and 10 several times
until the installation process is finished.

Page 99
 DEVICE CONFIGURATION GUIDE

10. After installation, go to Device Manager. You should see the following items:
Modems: Qualcomm HS-USB Modem 9001
Network adapters: Qualcomm HS-USB WWAN Adapter Modem 9001
Ports: Qualcomm HS-USB Diagnostics 9001

11. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

12. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to Qualcomm HS-USB Diagnostics
9001

 Modem port: Select the COM port number assigned to Qualcomm HS-USB Modem 9001

13. In the Device Configuration dialog, select <Automatic> as the PS data connection.
Click Apply.

14. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 100
 DEVICE CONFIGURATION GUIDE

30 NOKIA 6120/6121/6720(US)/
C5/C5-00.2/C5-03(US)/C5-04/C7-
00/E7-00/N85(US)/
N95(US)/N96(US)/N97(US)

 Do not connect the USB connectivity cable to your PC until the driver installation is
complete.

 With Nokia C5-03(US), C5-04, C7-00 and E7-00 the following settings are recommended
to improve stability:

 Set Theme effects to OFF

 Set Animated background to OFF

 Set Call image to none

 Set Screen saver to none

 Delete additional home screens

 Set widgets to offline mode

 Set WLAN scanning to OFF

 Set sensors to OFF

1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse to
folder Nemo Outdoor x.xx\Drivers\Nokia drivers and run the
Nokia_Connectivity_Driver_xxx.x.msi file (x is the latest driver version).

2. Click Next in the Welcome dialog. Select I accept… in the License Agreement dialog and
click Next.

3. Please read the safety notes carefully and then click Next in the Safety Information dialog.

4. Choose the destination folder and click Install.

5. Click Yes in the Digital Signature Not Found dialog if it appears. Otherwise, click Install.

6. After the connectivity cable driver installation is finished, Windows may restart your
computer but it is not required.

7. After your computer has restarted, connect the connectivity cable to the mobile and the
other end to the computer’s USB port. Windows will detect the new hardware automatically
and start the installation. The step is repeated several times until all new hardware is
added.

 Please note that with newer Nokia devices the Wizard may not appear at all and instead
the installation is performed automatically.

8. In the Welcome page, select No, not this time and click Next.

Page 101
 DEVICE CONFIGURATION GUIDE

9. Select Install the software automatically (Recommended) and click Next.

10. Click Yes or Continue Anyway in the Digital Signature Not Found or Hardware
Installation dialog if it appears. You may need to repeat steps 8, 9, and 10 several times
until the installation process is finished.

11. After installation, go to Device Manager. Select Start | Control Panel, open the Hardware
and sound tab and click the Device Manager button.

Page 102
 DEVICE CONFIGURATION GUIDE

12. Under Wireless Communication Devices you should see the Nokia xxxx USB Phone
Parent item. Under Modems, you should see three Nokia xxxx (USB) items. Leave the
Device Manager open as you will find there the COM port numbers needed in the next
steps.

13. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the terminal. Click Next.

14. In the Device Manager click on Modems. Select the COM port number assigned to the
first/unnumbered Nokia xxx USB item In the Trace Port field in the Device Configuration
dialog. Select the COM port number assigned to the second highest Nokia xxx USB item in
the Modem Port field.

15. In the Device Configuration dialog, select <Automatic> as the PS data connection.
Click Apply.

16. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 103
 DEVICE CONFIGURATION GUIDE

31 NOKIA 500

 Do not connect the USB connectivity cable to your PC until the driver installation is
complete.

1. The connectivity cable driver is located on the Nemo Outdoor USB flash drive. Browse to
folder Nemo Outdoor x.xx\Drivers\Nokia drivers\Nokia 500 and run the
Nokia_Suite_webinstaller_All file.

2. When the installation starts, choose your language and click Install.

3. Click I accept.

4. After the Nokia Suite installation is finished, close the installation dialog and connect the
connectivity cable to the mobile and the other end to the computer’s USB port. Windows will
detect the new hardware automatically and install the drivers.

5. After installation, go to Device Manager. Under Wireless Communication Devices you

should see the Nokia xxxx USB Phone Parent item. Under Modems, you should see
three Nokia xxxx (USB) items. Leave the Device Manager open as you will find there the
COM port numbers needed in the next steps.

Page 104
 DEVICE CONFIGURATION GUIDE

6. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the terminal. Click Next.

7. In the Device Manager click on Modems. Select the COM port number assigned to the
first/unnumbered Nokia xxx USB item In the Trace Port field in the Device Configuration
dialog. Select the COM port number assigned to the second highest Nokia xxx USB item in
the Modem Port field.

8. In the Device Configuration dialog, select <Automatic> as the PS data connection.

Click Apply.

9. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 105
 DEVICE CONFIGURATION GUIDE

32 NOVATEL OVATION
MC930D/MC990D/MC996D/
MC998D/MC545

 Prior to plugging the USB modem in your computer, please refer to the Novatel quick
start guide included in the product package for computer system requirements.

1. Insert the (U)SIM card supplied by your service provider in the terminal. Please refer to the
quick start guide for more detailed instructions as to how to do this.

2. Insert the Novatel Ovation USB modem into your PC USB port.

3. Windows will automatically install the device driver and detect the new device. In addition,
it automatically installs MobiLink Lite which is the device software. Ignore this software, and
close it. It should not be on when adding the device to Nemo Outdoor.

4. Next, go to Start | Control Panel | Phone and Modem Options | Modems on your PC.
The list should display Novatel Wireless Modem item and the associated COM port
number, in this case COM26.

Page 106
 DEVICE CONFIGURATION GUIDE

5. When the installation is complete, check from the Device Manager that the installation was
successful. Under Modems you should see the Novatel Wireless Modem item and under
Ports you should see the Novatel Wireless Application Port, Novatel Wireless EAP-SIM Port
and Novatel Wireless Status Port items. Under Network adapters you should see the
Novatel Wireless Network Adapter item. Leave the Device Manager open as you will find
there the COM port numbers needed in the next steps.

6. Exit the MobiLink Lite application before starting Nemo Outdoor.

7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

8. In the Device Manager click on Ports. Select the COM port number assigned to the
Novatel Wireless Application Port item in the Trace Port field in the Device
Configuration dialog. Click on Modems. Select the COM port number assigned to the
Novatel Wireless Modem item in the Modem Port field.

9. In the Device Configuration dialog, select <Automatic> as the PS data connection. For
Novatel Ovation 996D and 998D select <Automatic> in the PS Data Connection field. Click
Apply.

10. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 107
 DEVICE CONFIGURATION GUIDE

33 NOVATEL OVATION MC727/MC760

1. Plug in the Novatel Ovation USB modem data card.

2. Windows will automatically detect the new hardware. Select No, not this time and click
Next.

3. Select Install from a list or specific location and click Next.

4. Select Include this location in the search and browse to folder D:\Nemo Drivers\Novatel
MC727 usb drivers on the Nemo Outdoor USB flash drive. Click Next.

5. The driver files are installed. Steps 2, 3, and 4 are repeated several times until the new
hardware is ready to be used.

Page 108
 DEVICE CONFIGURATION GUIDE

6. When the installation is complete, check from the Device Manager that the installation was
successful. Under Ports you should see the Novatel Wireless Ovation EV-DO Diagnostic Port
(COMxx), Novatel Wireless Ovation EV-DO GPS Port (COMxx) and Novatel Wireless Ovation
EV-DO Status Port (COMxx )items. Leave the Device Manager open as you will find there
the COM port numbers needed in the next steps.

7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

8. In the Device Manager click on Ports. Select the COM port number assigned to the
Novatel Wireless Status Port item in the Trace Port field in the Device Configuration
dialog. Leave the Modem Port field empty.

9. In the Device Configuration dialog, select <Automatic> as the PS data connection. Click
Apply.

10. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 109
 DEVICE CONFIGURATION GUIDE

34 NSN USB-LTE 7210 (ALTAIR)

 Do not connect the USB connectivity cable to your PC until the driver installation prompts
you to do so.

1. First the Connection Manager is installed. The installation file is located on the Nemo
Outdoor USB flash drive. Browse the file and double-click the
LTE7210_xxxx_EngineeringRelease.exe file (xxxx refers to the version number).

2. First select the Installer language and click OK.

3. Click Next in the Welcome dialog. Click I Agree in the License Agreement dialog.

4. Choose the destination folder and click Next.

5. If at some point you see the Select Components dialog, select Full Installation and click
Next.

Page 110
 DEVICE CONFIGURATION GUIDE

6. Define the Start Menu Folder and click Install.

7. At some point during the Connection Manager installation, the Device Driver Installation
Wizard starts up automatically. Click Next in the Welcome dialog.

Page 111
 DEVICE CONFIGURATION GUIDE

8. The device driver installation is completed and you can now connect the device to your
computer. Click Finish.

9. Windows will automatically detect the new hardware and install the required drivers.

10. Return to the Connection Manager installation. When the installation is complete, click
Finish.

Page 112
 DEVICE CONFIGURATION GUIDE

11. The Connection Manager will launch automatically but it is important that it is closed
before adding the device to Nemo Outdoor. It is recommended that you rename the
.exe file that launches the Connection Manager to prevent the CM from starting. Browse to
C:\Program Files \NSN LTE Connection Manager (or for 64-bit Windows C:\Program Files
(x86)\NSN LTE Connection Manager) and rename the nsnltecm.exe to nsnltecm.exe_.

12. To avoid performance issues with the modem, the Altair LogCreator standalone functionality
needs to be disabled. Browse to folder C:\Program Files\NSN LTE Connection
Manager\Tools\ Internals\LogCreator and open file RunLogCreator.bat with Notepad.
Modify the following string:

 Original: LogCreator.exe -SA -FN:"50" -E -Y4:"LOG_SOCK_IF" -

D4:".\LoggerDB\LTELogDB.txt" -D1:".\LoggerDB\PhyFWLogDB.txt" -Q:"50000"

 Modified: LogCreator.exe -E -Y4:"LOG_SOCK_IF" -D4:".\LoggerDB\LTELogDB.txt" -

D1:".\LoggerDB\PhyFWLogDB.txt" -Q:"50000"

13. Go to Device Manager. Under Ports you should see Nokia Siemens Networks LTE Application
Interface item.

14. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select Altair. Click Next.

15. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select Altair USB

 Modem port: Select the COM port number assigned to the Nokia Siemens Networks LTE
Application Interface

16. In the Device Configuration dialog, select <NDIS> and click Apply.

17. If the device connecting fails, check that you have selected the correct COM ports and try
again. Also check that the NSN Connection Manager is not running.

Page 113
 DEVICE CONFIGURATION GUIDE

35 ONDA MT689DC

1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and start the installation. Click Run AutoRun.exe and follow the instructions
on the screen.

2. Select your language and destination folder. By clicking Next, you also accept the license
agreement.

3. When the installation is finished, unplug the device from the USB port and restart the
computer.

4. Plug the device back to the USB port. Close the AutoPay dialog.

5. If the Chiavetta Internet MT689DC software starts up, close the program.

6. After installation, go to Device Manager. Select Start | Control Panel, open the Hardware
and sound tab and click the Device Manager button.

Page 114
 DEVICE CONFIGURATION GUIDE

7. You should see the ONDA Proprietary HS-USB Modem item under Modems and the ONDA
HS-USB Diagnostics Interface item under Ports.

8. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

9. In the Device Configuration dialog, select the COM port number assigned to ONDA HS-
USB Diagnostics Interface item in the Trace Port field. Select the COM port number
assigned to the ONDA Proprietary HS-USB Modem item in the Modem Port field.

10. In the Device Configuration dialog, select <Automatic> as the PS data connection. Click
Apply.

11. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 115
 DEVICE CONFIGURATION GUIDE

36 PANTECH UM175

1. Unzip the driver files (PANTECH UM175 USB drivers.zip) on your computer.

2. Plug in the data card.

3. Windows will automatically detect the new hardware.

4. Select Install the software automatically (Recommended), and click Next.

5. Select Include this location in the search and browse for the folder where the driver
files are located (e.g., C:\Pantech UM175). Click Next.

Page 116
 DEVICE CONFIGURATION GUIDE

6. The driver files are installed. Click Finish.

7. Next go to Device Manager. Under Modems you should see the PANTECH UM175 item,
and under Ports the PANTECH UM175 Diagnostic Port item.

 If you do not see the items mentioned above and instead there are three unknown
devices under Others, the driver installation has failed. Right-click each unknown item,
select Update Driver Software, and browse to the folder where you unzipped the driver
files. After the update, the Pantech items should appear in the Device Manager.

8. Next, set up the data connection manually. Follow instructions on page 7 (for Win 7) then
continue from step 9.

Page 117
 DEVICE CONFIGURATION GUIDE

9. In the Pantech UM175 Modem Properties dialog, Security page, select No encryption
allowed in the Data encryption field. Click OK to close the dialog.

10. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

11. In the Nemo Outdoor Device Configuration dialog, define the following settings (check the
port numbers from the Device Manager) and click Apply:

 Trace port: Select the COM port number assigned to PANTECH UM175 Diagnostic Port

 Modem port: Select the COM port number assigned to PANTECH UM175

 PS data connection: Select the data connection that you configured manually, for
example, Pantech UM175

12. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 118
 DEVICE CONFIGURATION GUIDE

37 PANTECH UML290

 Do not plug in the device before installation!

1. Browse to folder D:\Drivers\Qualcomm LTE USB Modem on the Nemo Outdoor USB flash
drive.

2. Run the VZAM_7.6.3.4_2642j_PantechLTE.exe file to start the installation wizard. If the

Windows Security dialog appears, click Run.

3. The device drivers are installed first. After the device drivers are installed, the VZAccess
Manager installation is started.

4. Click Next in the Welcome window that appears.

5. Select I accept the terms in the license agreement and click Next.

Page 119
 DEVICE CONFIGURATION GUIDE

6. Click Next and Next. Select Typical in the Setup Type dialog and click Next and Install.
Wait until the installation is ready and click Finish.

7. Plug in the USB modem. Windows will automatically detect the new hardware and install
drivers. Wait until the installation process is finished.

8. After installation, go to Device Manager. Select Start | Control Panel | System, open the
Hardware tab and click the Device Manager button. You should see the Pantech
UML290 item under Modems and the Pantech UML290 Diagnostic Port item under
Ports.

Page 120
 DEVICE CONFIGURATION GUIDE

9. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

10. In the Device Manager click on Modems. Select the port assigned to Pantech UML290
Diagnostic Port in the Trace Port field in the Device Configuration dialog. Select the port
assigned to Pantech UML290 in the Modem Port field.

11. In the Device Configuration dialog, select <Automatic> as the PS data connection. Click
Apply.

12. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 121
 DEVICE CONFIGURATION GUIDE

38 SAMSUNG GALAXY CORE (SM-G386F)

 Do not connect the USB connectivity cable to your PC until the driver installation is
complete.

1. Insert the Nemo Outdoor installation DVD and browse to the driver folder (e.g. Nemo
Outdoor\Nemo Outdoor xx\ Drivers\Broadcom\Samsung Galaxy Core SM-G386F). Double-
click the Samsung USB Driver for Mobile Phones xxx.exe to run the installation.

2. When the installation is complete, connect the device to the PC.

3. Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial Port
item. Under Modems you should see the Samsung Mobile USB Modem item.

4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Broadcom item. Click Next.

5. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port (in the example above, COM34)

 Modem port: Select the COM port number assigned to the Samsung Mobile USB
Modem.

6. In the Device Configuration dialog, select SAMSUNG Mobile USB Remote NDIS Network
Device as the PS data connection (see page 7). Click Apply.

Page 122
 DEVICE CONFIGURATION GUIDE

7. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 123
 DEVICE CONFIGURATION GUIDE

39 SAMSUNG GALAXY S4 (GT-I9505,

SGH-I337, SPH-L720, SGH-M919,
SCH-R970, SGH-M919N, SGH-I337M),
GALAXY S4 ACTIVE (GT-I9295),
GALAXY S II (GT-I9210)

 Do not connect the USB connectivity cable to your PC until the driver installation is
complete.

 Check that the Mobile data setting is disabled from the device. Pull down the menu from
the top of the device screen and check that the Mobile data setting is grayed out. Also
check that WiFi and Bluetooth are disabled.

1. Insert the Nemo Outdoor USB flash drive and browse to the driver folder (e.g. Nemo
Outdoor\Nemo Outdoor xxx\Drivers\Qualcomm\Samsung\Samsung Galaxy S4). Double-
click the SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_22_0.exe file to start the
installation. Follow the steps in the installation wizard.

2. When the installation is complete, connect the terminal to your PC with the USB cable.
Windows will install the device drivers automatically.

Page 124
 DEVICE CONFIGURATION GUIDE

3. Go to Device Manager. Under Ports, you should see two Samsung Mobile USB Serial
Port items.

4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

5. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port with the bigger number. If device connecting fails, try the other port.

 Modem port: Select the COM port number assigned to Samsung Mobile USB Modem

 PS data connection: NDIS

6. Click Apply.

7. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 125
 DEVICE CONFIGURATION GUIDE

40 SAMSUNG GALAXY S II SKYROCKET,

GALAXY S II HD LTE (SHV-E120S
KOREAN VERSION)

 Do not connect the USB connectivity cable to your PC until the driver installation is
complete.

1. Insert the Nemo Outdoor installation DVD and browse to the driver folder. Double-click the
driver file (SAMSUNG_USB_Driver_for_Mobile_Phones) to start the installation. Click Next
in the Welcome dialog.

2. Select your language and country from the list and click Next.

3. Select the installation location and click Install.

4. The driver files are installed. Wait until the installation is finished and click Exit.

5. Switch on the mobile. Connect the USB cable to the mobile and the other end of the cable
to a USB port on your computer. Wait for Windows to detect the device.

Page 126
 DEVICE CONFIGURATION GUIDE

6. When the installation is complete, check from the Device Manager (Start | Control Panel |
Hardware | Device Manager) that the installation was successful. Under Modems you
should see the Samsung Mobile USB Modem item and under Ports you should see the
Samsung Mobile USB Serial Port item. Leave the Device Manager open as you will find there
the COM port numbers needed in the next steps.

7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

8. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port with the bigger port number (in the example above, COM53)

 Modem port: Select the COM port number assigned to the Samsung Mobile USB Modem

9. In the Device Configuration dialog, select <NDIS> as the PS data connection. Click
Apply.

10. If the device connecting fails, select the Samsung Mobile USB Serial Port with the smaller
port number and try again.

Page 127
 DEVICE CONFIGURATION GUIDE

41 SAMSUNG GALAXY S III (SGH-I747,

SGH-T999, SCH-I535, SPH-L710),
GALAXY RUGBY, GALAXY S4 MINI
(GT-I9195, SPH-L520), GALAXY S4
4G+ (GT-I9506), GALAXY NOTE 3
(SM-N9005, SM-N900T, SM-N9008V,
SM-N9007), GALAXY NOTE 3 LITE
(SM-N7509V), GALAXY NOTE 4 (SM-
N910F, SM-N910G, SM-N910T),
GALAXY S5 (ALL VARIANTS)

 Do not connect the USB connectivity cable to your PC until the driver installation is
complete.

 If the Samsung Galaxy S III terminal has been used with Nemo Handy, the device needs
to restarted or powered off/on before connecting it with Nemo Outdoor.

 With Galaxy S4 Mini (GT-I9195), Galaxy S4 4G+ (GT-I9506), and Galaxy Note 3 (SM-
N9005, SM-N900T TMOB): Check that the mobile data setting is disabled from the device.
Pull down the menu from the top of the device screen and check that the mobile data
setting is grayed out. Also check that WiFi and Bluetooth are disabled.

1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder (e.g.
Nemo Outdoor\Nemo Outdoor xx\Drivers\Qualcomm\Samsung\Samsung Galaxy Handsets).
Double-click the Samsung USB Driver for Mobile Phones xxx.exe to run the installation.

2. When the installation is complete, connect the device to the PC.

Page 128
 DEVICE CONFIGURATION GUIDE

3. Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial Port
item. Under Modems you should see the Samsung Mobile USB Modem item.

4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

5. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port (in the example above, COM34)

 Modem port: Select the COM port number assigned to the Samsung Mobile USB
Modem. Note! For Galaxy Note 3 (SM-N9005 variant only), select Not used.

6. In the Device Configuration dialog, select <NDIS> as the PS data connection. Click Apply.

7. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 129
 DEVICE CONFIGURATION GUIDE

 To be able to make voice calls, the voice call method must be selected in Nemo Outdoor
(Devices view - Voice call method - Trace interface). For Samsung Galaxy S III SGH-T999
and SGH-i747, select Trace interface 2. With S4 variants, leave the field empty.

Page 130
 DEVICE CONFIGURATION GUIDE

42 SAMSUNG GALAXY S6, GALAXY NOTE

5, GALAXY S6 EDGE+

 Samsung Galaxy S6 devices should be used with NMR (excluding the SM-G920A model).
See chapter Adding devices with Nemo Media Router.

 Before starting the installation, please note that there are two types of Samsung Galaxy
S6 devices and the installation instructions are chipset-specific:

1. Based on the Qualcomm chipset

2. Based on the Samsung Shannon chipset

 Do not connect the USB connectivity cable to your PC until the driver installation is
complete.

 Enable USB tethering from the device settings.

1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder (e.g.
Nemo Outdoor\Nemo Outdoor xx\Drivers\Samsung\Samsung Galaxy Handsets or Nemo
Outdoor\Nemo Outdoor xx\Drivers\Qualcomm\Samsung\Samsung Galaxy Handsets).
Double-click the Samsung USB Driver for Mobile Phones xxx.exe to run the
installation.

2. When the installation is complete, connect the device to the PC.

3. Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial Port
item. Under Modems you should see the Samsung Mobile USB Modem item.

4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Samsung or Qualcomm item, depending on the chipset of your
device. Click Next.

Page 131
 DEVICE CONFIGURATION GUIDE

5. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port (in the example above, COM29)

 Modem port: Select the COM port number assigned to the Samsung Mobile USB
Modem.

 For PS data connection select <Samsung Mobile USB Remote NDIS Network
Device>. Click Apply.

6. If the device connecting fails, check that you have selected the correct COM ports and try
again. You can also try selecting Not used for the Modem port.

Page 132
 DEVICE CONFIGURATION GUIDE

43 SAMSUNG GALAXY S7, GALAXY S7

EDGE

 Before starting the installation, please note that there are two types of Samsung Galaxy
S7 devices and the installation instructions are chipset-specific:

 Based on the Qualcomm chipset

 Based on the Samsung Shannon chipset

 Do not connect the USB connectivity cable to your PC until the driver installation is
complete.

 Enable USB tethering from the device settings.

1. Insert the Nemo Outdoor installation USB flash drive and browse to the driver folder (e.g.
Nemo Outdoor\Nemo Outdoor xx\Drivers\Samsung\Samsung Galaxy Handsets or Nemo
Outdoor\Nemo Outdoor xx\Drivers\Qualcomm\Samsung\Samsung Galaxy Handsets).
Double-click the Samsung USB Driver for Mobile Phones xxx.exe to run the
installation.

2. When the installation is complete, connect the device to the PC.

3. Go to Device Manager. Under Ports you should see the Samsung Mobile USB Serial Port
item. Under Modems you should see the Samsung Mobile USB Modem item.

4. Start Nemo Outdoor. Select Add | Phone. In the Add New Device dialog, click Phone and
select the Samsung or Qualcomm item, depending on the chipset of your device. Click
Next.

Page 133
 DEVICE CONFIGURATION GUIDE

5. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port (in the example above, COM29).

 Modem port: Select the COM port number assigned to the Samsung Mobile USB
Modem.

 For PS data connection select <Samsung Mobile USB Remote NDIS Network
Device>. Click Apply.

6. If the device connecting fails, check that you have selected the correct COM ports and try
again. You can also try selecting Not used for the Modem port.

Page 134
 DEVICE CONFIGURATION GUIDE

44 SAMSUNG GALAXY S III (GT-I9305),

GALAXY II NOTE (GT-N7105)

 If the terminal has been used with Nemo Handy, the device needs to restarted or
powered off/on before connecting it with Nemo Outdoor.

 When the UE is used with Nemo Outdoor, other terminals cannot be used simultaneously
in data testing if the NDIS interface is used to activate PS data connection. For example,
simultaneous data testing with Huawei LTE modem and Samsung Galaxy S III handset is
not possible. It should be noted that the issue does not limit using multiple Galaxy S III
terminals for simultaneous data testing or together with non-NDIS terminals, such as,
Nokia test terminals.

 To be able to make voice calls the “Trace interface 2” call method must be selected in
Nemo Outdoor (Devices view - Voice call method - Trace interface 2).

 Automatic answering to incoming calls can be done only when a headset is connected to
the terminal. Use the original headset included in the sales package. Connect the headset
to the phone and from the phone menu select: Settings -> Call Answering/ Ending->
Press arrow “<” on the left upper corner to go back to previous menu. Select Settings ->
Accessibility -> Call Settings -> Accessory Settings For Call -> Automatic Answering.
Automatic answering will operate only with the headset connected.

Page 135
 DEVICE CONFIGURATION GUIDE

 Auto detection should not be used to add the device. Add the device manually.

 Check that Enable USB auto tethering option is selected.

 USB mode must be RDNIS + DIAG + MODEM. Otherwise handset cannot be used with
Nemo Outdoor/ Invex. This is selected automatically when application is installed. Return
to main menu.

 If data testing is done manually without script files, recording must be started before
data protocols can be accessed via Nemo Outdoor. Without recording, the data protocol
options in the UI are not available.

 The following settings should be activated from the phone for data testing:

 Settings -> More settings -> Mobile networks -> Mobile data enabled-> Enable

 For Samsung Galaxy S III: Settings -> More settings -> Mobile networks -> Network Mode
-> AUTO

 For Samsung Galaxy II Note: Settings -> More settings -> Mobile networks -> Network
Mode -> Network Mode -> LTE/GSM/WCDMA (Auto mode)

 With Samsung Galaxy S III (GT-i9305) and Samsung Galaxy II Note (GT-N7105): The
device is always online. This means that attach/detach and PDP context
activation/deactivation commands cannot be used via Nemo Outdoor. It is recommended
that the access point name (APN) is defined for the phone manually. Otherwise the phone
can choose an incorrect APN automatically and this may cause the packet session to fail.

 Do not connect the USB connectivity cable to your PC until the driver installation is
complete.

1. Insert the Nemo Outdoor installation DVD and browse to the driver folder (e.g. Nemo
Outdoor\Nemo Outdoor xxx\Drivers\Qualcomm\Samsung\Samsung Galaxy S III). Double-
click the Kies_x.x.x.exe to start the installation.

2. Select the installation language.

3. Select I accept… in the License Agreement dialog and click Next. Wait for the installation
to finish. It may take several minutes.

4. If the Samsung Kies software starts, close the program. If the program suggests a driver
update, do not update.

5. When the installation is complete, connect the terminal to your PC with the USB cable.
Windows will install the device drivers automatically.

6. Go to Device Manager. Under Ports, you should see the Samsung Mobile USB Serial
Port item.

Page 136
 DEVICE CONFIGURATION GUIDE

7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

8. In the Nemo Outdoor Device Configuration dialog, define the following settings:

 Trace port: Select the COM port number assigned to the Samsung Mobile USB Serial
Port (in the example above, COM15)

 Modem port: Select Not Used.

 PS data connection: Automatic

9. Click Apply.

10. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 137
 DEVICE CONFIGURATION GUIDE

45 SIERRA WIRELESS AIRCARD

306/307/308/309/310U/
312U/313U/320U/330U, SIERRA
COMPASS 889, SIPTUNE SM215

1. Plug in the USB data card. The data card automatically starts the 3G Watcher driver
installation. Siptune SM215 comes with its own driver installation software on a separate
USB stick. Follow the instructions in the installation wizard.

2. When the installation is ready, Windows automatically detects the device and installs the
driver files.

3. Open the Telstra Turbo Connection Manager main view. Note that the name of the
Connection Manager may vary, for example, depending on the operator the device comes
equipped with. For example, Sierra Wireless Watcher comes with Sierra 306.

Page 138
 DEVICE CONFIGURATION GUIDE

4. Select Tools | Options. In the User Options window, select No in the Autolaunch on
device insertion or power-up, Do nothing for the On exit field or No in Turn radio off
on exit, Never for Check for updates.

5. When these options are selected, you can close the Telstra Turbo Connection
Manager/Watcher application, and the device will work in Nemo Outdoor. However, if these
options are not selected, the Telstra Turbo Connection Manager/Watcher application needs
to run in the background while conducting measurements with the Sierra device in Nemo
Outdoor.

 Note that the options may vary depending on the device. For example, with Sierra 306,
the Tools button is a spanner icon, and instead of On exit field there is Enable airplane
mode on exit which needs to be set to No. In addition, the modem name may change
depending on the device, for example, to Sierra Wireless HSPA modem.

Page 139
 DEVICE CONFIGURATION GUIDE

6. When the installation is complete, check from the Device Manager that the installation was
successful. Go to Start | Control Panel | System and Security | System | Device
Manager. Under Modems you should see a Sierra Wireless AirCard HSDPA Modem item
and under Ports pay attention to the Sierra Wireless AT Command Port (UMTS) (COMxx)
and Sierra Wireless DM Port (UMTS) (COMxx) items. Under Network Adapters you should
see the Sierra Wireless HSPA Network Adapter item. Leave the Device Manager open as you
will find there the COM port numbers needed in the next steps.

7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

8. In the Device Manager click on Ports. Select the COM port number assigned to the Sierra
Wireless DM Port item in the Trace Port field in the Device Configuration dialog. Click on
Modems. Select the COM port number assigned to the Sierra Wireless AT Command
Port item in the Modem Port field.

9. In the Device Configuration dialog, select <Automatic> as the PS data connection. Click
Apply.

10. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 140
 DEVICE CONFIGURATION GUIDE

46 SIERRA WIRELESS COMPASS 597

1. Insert the USB data card in a free USB slot on your PC.

2. The Sprint SmartView installation setup starts automatically. Double-click on the setup.exe
file, and click Setup.

3. Click Next in the Welcome window that appears and follow the instructions in the setup
wizard.

4. In the License Agreement window, select I accept the terms in the license agreement,
and click

5. After the installation is completed, the software will ask you to restart your computer. Click
Yes.

6. Go to Start | Control Panel | Hardware | Device Manager. Double-click on Modems to

expand it. You should see the Sierra Wireless Compass 597 EVDO Modem item. You
should also see the Sierra Wireless Compass 597 DM Port (COMxx) item under Ports. Leave
the Device Manager open as you will find there the COM port numbers needed in the next
steps.

7. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

Page 141
 DEVICE CONFIGURATION GUIDE

8. In the Device Manager click on Ports. Select the COM port number assigned to the Sierra
Wireless Compass 597 DM Port item in the Trace Port field in the Device
Configuration dialog. Leave the Modem Port field empty.

9. In the Device Configuration dialog, select <Automatic> as the PS data connection. Click
Apply.

10. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 142
 DEVICE CONFIGURATION GUIDE

47 SONY XPERIA Z3 (D6603, D6653),

Z5 (E6653)

1. Run the install.bat file from folder Drivers\Qualcomm\Sony Ericsson\Sony_Ericsson Z3 (for

Z3) or Drivers\Qualcomm\Sony Ericsson\Sony Xperia Z5 (for Z5) found on the Nemo
Outdoor USB flash drive to start the installation wizard and wait for the installation to finish.

2. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and install the device drivers.

3. Go to Device Manager. You should see the following items:

 Modems: Sony HS-USB Android Modem

 Network adapters:

a. For Z3 devices: Sony Wireless Ethernet Adapter

b. For Z5 devices: Remote NDIS based Internet Sharing Device

 Ports: Sony HS-USB Android Diag-0

4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

Page 143
 DEVICE CONFIGURATION GUIDE

5. In the Device Configuration dialog, make the following settings and click Apply:

 Trace Port: Select the port assigned to Sony HS-USB Android Diag-0

 Modem Port: Select the port assigned to Sony HS-USB Android Modem

 PS data connection:

a. For Z3 devices: select Automatic

b. For Z5 devices: select Remote NDIS based Internet Sharing Device

6. If the device connecting fails, check that you have selected the correct COM ports and try
again.

47.1 Configuring Sony Xperia Z3 (D6603, D6653) for use with

Nemo Invex II Handset Isolation Module
 Please note that if you have more than one HIM connected to the same UIC, the first two
steps need to be executed only for the first device.

1. Copy the Sony Xperia Eng Drivers folder on the Nemo Invex II UIC to which the HIM is
connected.

2. Run the install.bat file to start the installation wizard and follow the instructions on the
screen to finish the installation.

3. Connect the HIM with the device to the UIC USB port. Windows will detect the new
hardware automatically and install the device drivers.

4. Go to Device Manager on the UIC. Under Other devices, you will see the RNDIS item.

5. Right-click the RNDIS item and select Update Driver Software.

Page 144
 DEVICE CONFIGURATION GUIDE

6. Select Browse my computer for driver software.

7. Select Let me pick from a list...

Page 145
 DEVICE CONFIGURATION GUIDE

8. Select Show All Devices and click Next.

9. Click Have Disk.

Page 146
 DEVICE CONFIGURATION GUIDE

10. Click Browse. Browse to the Sony Xperia Eng Drivers folder and click OK.

11. Select the Sony Android Remote NDIS based Device item and click Next.

Page 147
 DEVICE CONFIGURATION GUIDE

12. Click Yes to continue.

13. When the installation is finished, go back to the Device Manager. Under Network
adapters, you should now see the Sony Android Remote NDIS based Device item.

14. You can now add the device in Nemo Outdoor. Please refer to chapter Nemo Invex device
set-up in the Nemo Outdoor User Guide.

Page 148
 DEVICE CONFIGURATION GUIDE

48 SONY ERICSSON XPERIA ARC S

 Please note that currently the Sony Ericsson Xperia Arc S driver can be installed on 32-bit
Windows 7 only.

1. Before connecting the Sony Ericsson Xperia Arc S to a computer, make the following
settings on the device. Go to Settings | Applications | Development. Deselect USB
debugging.

2. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically.

3. Open the Device Manager. Under Other devices you will see two SEMC HSUSB Device items.
If an MTP device appears instead of SEMC HSUSB, expand the Universal Serial Bus
controllers item, and delete the USB Mass Storage Device item. Then disconnect and
reconnect the data cable from the mobile. The device should now be detected correctly.

4. Right-click on the first item and select Update Driver Software.

Page 149
 DEVICE CONFIGURATION GUIDE

5. Select Browse my computer for driver software.

6. Select Let me pick from a list of device drivers on my computer.

Page 150
 DEVICE CONFIGURATION GUIDE

7. Select Show All Devices and click Next.

8. Select Have Disk.

Page 151
 DEVICE CONFIGURATION GUIDE

9. Browse to the folder on the Nemo Outdoor USB flash drive where the Sony Ericsson drivers
are and click Open.

10. Click OK.

Page 152
 DEVICE CONFIGURATION GUIDE

11. Select the Sony Ericsson sa0102 Device Modem item and click Next.

12. Click Yes in the Update Driver Warning message.

13. Click Close when the installation is finished.

Page 153
 DEVICE CONFIGURATION GUIDE

14. Return to the Device Manager. The Sony Ericsson sa0102 Device Modem item should
appear under Modems and there should be one SEMC HSUSB Device item under Other
devices.

15. Again, right-click on the SEMC HSUSB Device item and select Update Driver Software.
Repeat steps 3-9.

Page 154
 DEVICE CONFIGURATION GUIDE

16. Select the Sony Ericsson HS-USB Android Diag sa0102 item and click Next.

17. Click Yes in the Update Driver Warning message and click Close when the installation is
finished.

18. Return to the Device Manager. The Sony Ericsson HS-USB Android Diag sa0102 item
should appear under Ports.

Page 155
 DEVICE CONFIGURATION GUIDE

19. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

20. Select the port assigned to Sony Ericsson HS-USB Android Diag sa0102 in the Trace Port
field in the Device Configuration dialog. Select the port assigned to Sony Ericsson sa0102
Device Modem in the Modem Port field.

21. In the Device Configuration dialog, select <Automatic> as the PS data connection. Click
Apply.

22. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 156
 DEVICE CONFIGURATION GUIDE

49 SONY XPERIA X PERFORMANCE

F8131, F8132, X F5121, XZ F8331

1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically.

2. To install a driver, select the Sony_Eng_Drivers item and click Next.

3. Click Yes in the Update Driver Warning message.

4. Click Close when the installation is finished.

5. Return to the Device Manager. The Sony HS-USB Android Modem item should appear
under Modems.

6. Again, right-click on the Sony HS-USB Android Modem and select Update Driver
Software.

7. Select the Sony_Eng_Drivers item and click Next.

8. Click Yes in the Update Driver Warning message and click Close when the installation is
finished.

9. Return to the Device Manager. The Sony HS-USB Android Diag item should appear under
Ports.

Page 157
 DEVICE CONFIGURATION GUIDE

10. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

11. Select the port assigned to Sony HS-USB Android Diag in the Trace Port field in the Device
Configuration dialog. Select the port assigned to Sony HS-USB Android Modem in the
Modem Port field.

12. In the Device Configuration dialog, select <Automatic> as the PS data connection. Click
Apply.

13. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 158
 DEVICE CONFIGURATION GUIDE

Page 159
 DEVICE CONFIGURATION GUIDE

50 ZTE MF820T/MF820D

1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and install the device drivers.

2. The Mobile Broadband application will be installed next. Click Run Setup.exe and follow the
instructions on the screen. Select Yes in the User Account Control dialog if it appears.

 When the installation is finished, it is important to close the Mobile Broadband

application.

3. Go to Device Manager. You should see the following items:

 Network adapters: ZTE Mobile Broadband Network Adapter

 Ports: ZTE Mobile Broadband AT Port and ZTE Mobile Broadband Diagnostics Port

4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

5. In the Device Configuration dialog, make the following settings and click Apply:

 Trace Port: Select the port assigned to ZTE Mobile Broadband Diagnostics Port

 Modem Port: Select the port assigned to ZTE Mobile Broadband AT Port

 PS data connection: Select <NDIS>.

6. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 160
 DEVICE CONFIGURATION GUIDE

51 ZTE MF668A

1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and install the device drivers.

2. The Mobile Broadband application will be installed next. Click Run Setup.exe and follow the
instructions on the screen. Select Yes in the User Account Control dialog if it appears.

 When the installation is finished, it is important to close the Mobile Broadband

application.

3. Go to Device Manager. You should see the following items:

 Modems: ZTE Proprietary USB Modem

 Network adapters: ZTE Wireless Ethernet Adapter

 Ports: ZTE Diagnostics Interface and ZTE NMEA Device

4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

5. In the Device Configuration dialog, make the following settings and click Apply:

 Trace Port: Select the port assigned to ZTE Diagnostics Interface

 Modem Port: Select the port assigned to ZTE Proprietary USB Modem

 PS data connection: Select <NDIS>.

6. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 161
 DEVICE CONFIGURATION GUIDE

52 ZTE MF683

1. Start the driver installation by selecting the correct installation file based on your operating
system (..\Drivers\Qualcomm\ZTE\ZTE MF683\USBDriverInstaller_x64.exe or
USBDriverInstaller_x86.exe). The installation will run on the background.

2. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and install the device drivers.

3. Go to Device Manager. You should see the following items:

 Modems: T-Mobile HSPA+ Modem

 Network adapters: T-Mobile Wireless Ethernet Adapter

 Ports: T-Mobile Diagnostics Port.

4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

5. In the Device Configuration dialog, make the following settings and click Apply:

 Trace Port: Select the port assigned to T-Mobile Diagnostics Port

 Modem Port: Select the port assigned to T-Mobile HSPA+ Modem

 PS data connection: Select <Automatic>.

6. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 162
 DEVICE CONFIGURATION GUIDE

53 ZTE MF880

1. Connect the device to your computer’s USB port. Windows will detect the new hardware
automatically and install the device drivers.

2. The Mobile Broadband application will be installed next. Click Run Setup.exe and follow the
instructions on the screen. Select Yes in the User Account Control dialog if it appears.

 When the installation is finished, it is important to close the Mobile Broadband

application.

3. Go to Device Manager. You should see the following items:

 Modems: ZTE Mobile Broadband Modem

 Network adapters: ZTE Mobile Broadband Network Adapter

 Ports: ZTE Mobile Broadband Diagnostics Port

4. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Qualcomm item. Click Next.

5. In the Device Configuration dialog, make the following settings and click Apply:

 Trace Port: Select the port assigned to ZTE Mobile Broadband Diagnostics Port

 Modem Port: Select the port assigned to ZTE Mobile Broadband Modem

 PS data connection: Select <NDIS>.

6. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 163
 DEVICE CONFIGURATION GUIDE

54 ZTE TU25

 Make sure that the device is NOT connected to your computer.

1. The installer executable is named ZTE_Common_API.msi, and it can be found on the USB
flash drive. Click Run to run the installer.

2. Click Next in the Welcome dialog.

3. Click Next in the Destination Folder dialog.

4. Click Install.

5. Click Continue Anyway.

6. Finally click Finish. The driver is now installed. Next, plug in the USB device.

7. Click Continue Anyway until the prompt no longer appears.

Page 164
 DEVICE CONFIGURATION GUIDE

8. Next, browse to Start | Control Panel | Hardware and Sound and click on the Device
Manager button. Under Network adapters you should see the ZTE WiMAX BCM1000 item.

9. Start Nemo Outdoor. Select Measurement | Add New Device. In the New Device dialog,
click Phones and select the Beceem BCS200 (524) item. Click Next.

10. In the Device Manager click on Modems. Select the BECEEM USB in the Trace Port field in
the Device Configuration dialog. Leave the Modem Port field empty.

11. In the Device Configuration dialog, select <Automatic> as the PS data connection. Click
Apply.

12. If the device connecting fails, check that you have selected the correct COM ports and try
again.

Page 165
 DEVICE CONFIGURATION GUIDE

55 APPLICATION TESTER

These guidelines apply to any commercial terminal, i.e. a terminal not provided by Anite Network
Testing, that is used for application testing.

1. First you need to install the connectivity cable driver. The USB connectivity cable driver and
an applicable USB connectivity cable for it will be included in your mobile phone package.
Note! Do not connect the USB connectivity cable to your PC until the driver
installation is complete! Consult the terminal user manual for instructions on how to
install the connectivity cable driver.

2. After installing the connectivity cable driver, go to Start | Control Panel | Phone and
Modem Options | Modems and check the Modem port number assigned to the terminal.
This port number will be the same as the Modem port in Nemo Outdoor.

3. Next you need to create a dial-up connection to the Internet for the modem port mentioned
above. A dial-up networking installation is required before data transfers can be made. Go
to Start | Control Panel | Network Connections. Check to see if the dial-up connection
for your phone was automatically installed with the USB connectivity driver installation. If
not, create a new dial-up connection from File | New Connection. The dial-up connection
you find in the Network Connections window is the same as the PS data connection in Nemo
Outdoor.

4. When the USB connectivity driver and dial-up networking installations are complete, go to
Nemo Outdoor and select Measurement | Add New Device | Phone | Application
Tester. In the Device Configuration dialog select the applicable modem port. The Trace
port field is grayed out. In the PS data connection field, select the dial-up connection
created earlier. Click Apply. If the status field does not say Device is working properly,
check to see that you have selected the right port number and try again.

5. You can also check the earlier chapters in this document for possible similarities to the
installation procedures of your terminal.

Page 166
 DEVICE CONFIGURATION GUIDE

56 TECHNICAL SUPPORT

If you have questions on or beyond this documentation about Nemo tools, please contact our
technical support service through Nemo Support Portal at http://nemosupport.anite.com, call us
(local phone numbers can be found in chapter Phone and email support) or send us an email at
[email protected]. Note that for full support you need to have the Maintenance Agreement.

56.1 User Club

Nemo User Club offers several new ways to benefit from Nemo products. You can find it from
http://nemouserclub.anite.com.

Access to the Nemo User Club is restricted to customers with SW maintenance and
Technical Support agreements or partner agreements. If you are an existing Anite Network
Testing customer with SW maintenance and Technical Support agreements, but you are without
access to the User Club, please complete an on-line registration form.

After submitting the requested information, you will receive a personal access key and password by
email in a few days time.

Once you are registered with our User Club, you will automatically receive e-mails informing you
each time a new version of software for your Nemo Product is released. It is fast, easy, and it is
available to you seven days a week, 24 hours a day.

56.2 Nemo Support Portal

Nemo Support Portal is a web interface for technical support, product-related questions, and RMA
requests. It offers a fast and convenient way to reach our technical support team and submit repair,
warranty repair, and calibration requests. Customers can open a support ticket, follow the status of
existing tickets, and request technical support 24/7/365. Furthermore, the Nemo Support Portal
includes a Knowledge Base for the most frequent and latest topics on Nemo Products. Submitting a
ticket via Nemo Support Portal ensures that our technical specialists have all the necessary
information available to solve your support case, resulting in faster response times.

Please go to http://nemosupport.anite.com to access the portal and click “Request access” to obtain
a password to the system.

56.3 Phone and email support

During the warranty period, the phone support related to potential software errors is free of
additional charge. Registered users with a valid Maintenance Agreement are entitled to full support.
Nemo Support Portal is the preferred channel for technical support requests, but you can also send
us an email. When emailing, please let us know the number of your Software Maintenance and
Support Agreement.

Page 167
 DEVICE CONFIGURATION GUIDE

Please contact us at the following locations:

Global

Mobile +358 50 395 7800

Americas

Mobile +1 469 951 9105

APAC

Tel. +65 9746 2431

P.R. China

Tel. +86 10 6567 8528

India

Tel. +91 982 0016372

Middle East

Tel. +86 10 6567 8528

P.R. China

Tel. +97 155 620 4132

Page 168