9/22/2016

A+ Guide to Managing & Maintaining

Your PC, 8th Edition

Chapter 6
Supporting Hard Drives

Objectives

• Learn about the technologies used inside a hard

drive and how a computer communicates with a
hard drive
• Learn how to select and install a hard drive
• Learn about tape drives and floppy drives

A+ Guide to Managing & Maintaining Your 2

© Cengage Learning 2014
PC, 8th Edition

1
 9/22/2016

Hard Drive Technologies and Interface

Standards
• Hard disk drive (HDD) or hard drive sizes
– 2.5" size for laptop computers
– 3.5" size for desktops
– 1.8" size for low-end laptops, other equipment

A+ Guide to Managing & Maintaining Your 3

© Cengage Learning 2014
PC, 8th Edition

Technologies Used Inside a Hard Drive

• Solid state drive (SSD) or solid state device (SSD)
– No moving parts
– Built using nonvolatile flash memory stored on
EEPROM (Electronically Erasable Programmable
Read Only Memory) chips
– Memory in an SSD is called NAND flash memory
– Lifespan is based on the number of write operations
to the drive
– Expensive technology, but faster, more reliable, last
longer, and use less power than magnetic drives

A+ Guide to Managing & Maintaining Your 4

© Cengage Learning 2014
PC, 8th Edition

2
 9/22/2016

Technologies Used Inside a Hard Drive

• Magnetic hard drive
– One, two, or more platters, or disks
• Stacked together, spinning in unison inside a sealed
metal housing
– Firmware controls data reading, writing and
motherboard communication
– Read/write heads are controlled by an actuator
– Data is organized in concentric circles, called tracks
• Tracks are divided into segments called sectors
– Most current drives use 4096-byte sectors
• Hybrid hard drives use both technologies
– Operating system must support it
A+ Guide to Managing & Maintaining Your 5
© Cengage Learning 2014
PC, 8th Edition

Figure 6-2 Solid-state drives by Toshiba

A+ Guide to Managing & Maintaining Your 6

© Cengage Learning 2014
PC, 8th Edition

3
 9/22/2016

Figure 6-3 Inside a magnetic hard drive

A+ Guide to Managing & Maintaining Your 7

© Cengage Learning 2014
PC, 8th Edition

Figure 6-4 A hard drive or floppy disk is divided into tracks and
sectors; several sectors make one cluster

A+ Guide to Managing & Maintaining Your 8

© Cengage Learning 2014
PC, 8th Edition

4
 9/22/2016

Technologies Used Inside a Hard Drive

• Low-level formatting – sector markings are written to

the hard drive at the factory
– Not the same as high-level formatting performed for
Operating System installation
• Firmware, BIOS and OS use logical block
addressing (LBA) to address all hard drive sectors
– Size of each sector + total number of sectors
determine drive capacity
• S.M.A.R.T – Self-Monitoring Analysis ad Reporting
Technology
– Used to predict when a drive is likely to fail
A+ Guide to Managing & Maintaining Your 9
© Cengage Learning 2014
PC, 8th Edition

Interface Standards Used By a Hard

Drive
• Current internal hard drives methods
– Parallel ATA (PATA) and Serial ATA (SATA)
• External hard drive methods
– External SATA (eSATA), SCSI, FireWire, USB, Fibre
Channel

Figure 6-5 Timeline of interface standards used by internal drives

A+ Guide to Managing & Maintaining Your 10

© Cengage Learning 2014
PC, 8th Edition

5
 9/22/2016

Interface Standards Used by a Hard

Drive
• Interface standards define data speeds and transfer
methods with a computer system
– Also define types of cables and connectors
• Standards
– Developed by Technical Committee T13
– Published by American National Standards Institute
(ANSI)

A+ Guide to Managing & Maintaining Your 11

© Cengage Learning 2014
PC, 8th Edition

Table 5-1 Summary of ATA interface standards for storage devices

A+ Guide to Managing & Maintaining Your 12

© Cengage Learning 2014
PC, 8th Edition

6
 9/22/2016

Parallel ATA or EIDE Drive Standards

• Parallel ATA or EIDE drive standards or Integrated
Drive Electronics (IDE)
– Allows one or two IDE connectors on a motherboard
• Each use 40-pin data cable
– Advanced Technology Attachment Packet Interface
• Required by optical drives (e.g., CD or DVD)
• Types of PATA ribbon cables
– Older cable
• 40 pins and 40 wires
– 80-conductor IDE cable
• 40 pins and 80 wires
– Maximum recommended length of either is 18”
A+ Guide to Managing & Maintaining Your 13
© Cengage Learning 2014
PC, 8th Edition

Figure 6-9 In comparing the 80-conductor cable to the 40-conductor cable, note they are
about the same width, but the 80-conductor cable has many more and finer wires

A+ Guide to Managing & Maintaining Your 14

© Cengage Learning 2014
PC, 8th Edition

7
 9/22/2016

Parallel ATA or EIDE Drive Standards

• Transferring data between hard drive and memory
– Direct memory access (DMA) transfer mode
• Transfers data directly from drive to memory without
involving the CPU
• Seven DMA modes
– Programmed Input/Output (PIO) transfer mode
• Involves the CPU, slower than DMA mode
• Five PIO modes used by hard drives
– Ultra DMA
• Data transferred twice for each clock beat, at the
beginning and again at the end

A+ Guide to Managing & Maintaining Your 15

© Cengage Learning 2014
PC, 8th Edition

Parallel ATA or EIDE Drive Standards

• Startup BIOS
– Autodetects drive and selects fastest mode that drive
and BIOS support
• Independent Device Timing
– Motherboard chipset feature
– Supported by most chipsets today
– Allows two hard drives to share same parallel ATA
cable but use different standards
– Allows two drives to run at different speeds as long as
motherboard supports them

A+ Guide to Managing & Maintaining Your 16

© Cengage Learning 2014
PC, 8th Edition

8
 9/22/2016

Serial ATA Standards

• Serial ATA standards
– Developed by a consortium of manufacturers
• Serial ATA International Organization (SATA-IO)
– Uses serial data path rather than traditional parallel
data path
– Advantages
• Faster than PATA interfaces and used by all drive types
• Multiple connectors are easy to configure
• Supports hot-swapping (hot-plugging)
– Connect and disconnect drive while system is running
• Internal cable length: up 1 meter
• Cable does not hinder airflow (narrower than PATA)
A+ Guide to Managing & Maintaining Your 17
© Cengage Learning 2014
PC, 8th Edition

Figure 6-12 A SATA data cable and SATA power cable

A+ Guide to Managing & Maintaining Your 18

© Cengage Learning 2014
PC, 8th Edition

9
 9/22/2016

Table 5-2 SATA Standards

A+ Guide to Managing & Maintaining Your 19

© Cengage Learning 2014
PC, 8th Edition

Serial ATA Standards

• Serial ATA standards (cont’d.)

– Motherboard or expansion card can provide external
SATA (eSATA) ports for external drives
– External SATA (eSATA)
• eSATA drives use special external shielded serial ATA
cable up to 2 meters long
– Purchasing considerations
• SATA standards for the drive and motherboard need to
match for optimum speed
• If no match, system runs at the slower speed

A+ Guide to Managing & Maintaining Your 20

© Cengage Learning 2014
PC, 8th Edition

10
 9/22/2016

SCSI Technology
• Small Computer System Interface standards
– Used primarily in servers
– Support either 7 or 15 devices (standard dependent)
– Provides better performance than ATA standards
• SCSI subsystem
– SCSI controller types: embedded or host adapter
– Host adapter supports internal and external devices
– Daisy chain: combination of host adapter and devices
– Each device on bus assigned SCSI ID (0 - 15)
– A physical device can embed multiple logical devices
• Assigned a Logical Unit Number (LUN)
A+ Guide to Managing & Maintaining Your 21
© Cengage Learning 2014
PC, 8th Edition

Figure 6-15 Using a SCSI bus, a SCSI host adapter card can support
internal and external SCSI devices

A+ Guide to Managing & Maintaining Your 22

© Cengage Learning 2014
PC, 8th Edition

11
 9/22/2016

SCSI Technology
• Terminating resistor
– Plugged into last device at end of the chain
– Reduces electrical noise or interference on the cable
• Categories of SCSI Standards
– 8-bit (narrow SCSI)
• Uses 50-pin SCSI connector (A cable) or 25-pin SCSI
connector that looks like a parallel port (DB-25)
– 16-bit (wide SCSI)
• Uses 68-pin SCSI connector (P cable)

A+ Guide to Managing & Maintaining Your 23

© Cengage Learning 2014
PC, 8th Edition

SCSI Technology
• Various SCSI versions
– SCSI-1, SCSI-2, and SCSI-3
• Also known as regular SCSI, Fast SCSI, Ultra SCSI
• Serial attached SCSI (SAS)
– Allows for more than 15 devices on single chain
– Uses smaller, longer, round cables
– Uses smaller hard drive form factors, larger capacities
– Compatible with serial ATA

A+ Guide to Managing & Maintaining Your 24

© Cengage Learning 2014
PC, 8th Edition

12
 9/22/2016

Figure 6-18 The most popular SCSI connectors are 50-pin, A-cable connectors
For narrow SCSI and 68-pin, P-cable connectors for wide SCSI
A+ Guide to Managing & Maintaining Your 25
© Cengage Learning 2014
PC, 8th Edition

How to Select and Install Hard Drives

• Topics covered
– Selecting a hard drive
– Installation details for SATA drive, IDE drive
– How to install hard drive in a bay too wide for drive
– How to set up a RAID system

A+ Guide to Managing & Maintaining Your 26

© Cengage Learning 2014
PC, 8th Edition

13
 9/22/2016

Selecting a Hard Drive

• Hard drive must match OS and motherboard

– Need to know what standards the motherboard or
controller card providing the drive interface can use
– Consult documentation for the board or card
• BIOS uses autodetection to prepare the device
– Drive capacity and configuration selected
– Best possible ATA standard becomes part of
configuration

A+ Guide to Managing & Maintaining Your 27

© Cengage Learning 2014
PC, 8th Edition

Selecting a Hard Drive

• Considerations:
– Drive capacity
• Today’s desktop hard drives range from 60 GB – 2 TB
– Spindle speed
• Most common is 7200 RPM
• The higher the RPMs, the faster the drive
– Interface standard
• Use standards the motherboard supports
– Cache or buffer size
• Ranges from 2 MB to 64 MB

A+ Guide to Managing & Maintaining Your 28

© Cengage Learning 2014
PC, 8th Edition

14
 9/22/2016

Steps to Install a Serial ATA Drive

• Some SATA drives have two power connectors

– Choose only one to use
– Never install two power cords at the same time
• If you have a SATA drive and a PATA connector (or
vice versa)
– Purchase an adapter to make the drive fit the
motherboard connection
– Can also purchase a SATA and/or PATA controller
card

A+ Guide to Managing & Maintaining Your 29

© Cengage Learning 2014
PC, 8th Edition

Steps to Install a Serial ATA Drive

• Step 1: Know your starting point

– How is your system configured?
– Is everything working properly?
– Write down what you know about the system
• Step 2: Read the documentation and prepare your
work area
– Read all installation instructions first
– Visualize all the steps
– Protect against ESD and avoid working on carpet

A+ Guide to Managing & Maintaining Your 30

© Cengage Learning 2014
PC, 8th Edition

15
 9/22/2016

Steps to Install a Serial ATA Drive

• Step 2: Read the documentation and prepare your

work area (cont’d)
– Handle the drive carefully
– Do not touch any exposed circuitry
– Drain static electricity from the package and from your
body by touching metal for at least 2 seconds
– Do not place the drive on the computer case or on a
metal table

A+ Guide to Managing & Maintaining Your 31

© Cengage Learning 2014
PC, 8th Edition

Steps to Install a Serial ATA Drive

• Step 3: Install the drive

– Turn off the computer and unplug it
– Decide which bay will hold the drive
– Slide drive in the bay and secure it (use two screws
on both sides)
– Use correct motherboard serial ATA connector
– Connect a 15-pin SATA or 5-pin Molex power
connector from the power supply to the drive
– Check all connections and power up the system
– Verify drive recognized correctly via BIOS setup

A+ Guide to Managing & Maintaining Your 32

© Cengage Learning 2014
PC, 8th Edition

16
 9/22/2016

Steps to Install a Serial ATA Drive

• Now ready to prepare the hard drive for first use

– Boot from Windows setup CD or DVD
• Follow directions on the screen to install Windows on
the new drive
– If installing a second hard drive with Windows
installed on first drive use Windows Disk
Management utility to partition and format the second
drive

A+ Guide to Managing & Maintaining Your 33

© Cengage Learning 2014
PC, 8th Edition

Steps to Install a Serial ATA Drive

• Installing a drive in a removable bay

– Unplug the cage fan from its power source
– Turn handle on each locking device counterclockwise
to remove it
– Slide the bay to the front and out of the case
– Insert hard drive in the bay
• Use two screws on each side to anchor the drive in the
bay
– Slide the bay back into the case
– Reinstall the locking pins

A+ Guide to Managing & Maintaining Your 34

© Cengage Learning 2014
PC, 8th Edition

17
 9/22/2016

Figure 6-30 The removable bay Figure 6-31 Install the hard drive in the
has a fan in front and is anchored bay using two screws on each side of the
to the case with locking pins drive

A+ Guide to Managing & Maintaining Your 35

© Cengage Learning 2014
PC, 8th Edition

Steps to Configure and Install a Parallel

ATA Drive
• Configurations for four EIDE devices in a system:
– Primary IDE channel, master device
– Primary IDE channel, slave device
– Secondary IDE channel, master device
– Secondary IDE channel, slave device

Figure 6-35 A motherboard supporting PATA has two IDE channels;

each can support a master and slave drive using a single EIDE cable

A+ Guide to Managing & Maintaining Your 36

© Cengage Learning 2014
PC, 8th Edition

18
 9/22/2016

Steps to Configure and Install a Parallel

ATA Drive
• Master or slave designations are made by:
– Setting jumpers or DIP switches
– Use special cable-select data cable
– Color-coded connectors
• Blue end connects to motherboard; black end connects
to drive

Figure 6-36 80-conductor cable connectors are color-coded

A+ Guide to Managing & Maintaining Your 37

© Cengage Learning 2014
PC, 8th Edition

Steps to Configure and Install a Parallel

ATA Drive
• Motherboard color-coding
– Primary channel connector: blue
– Secondary channel connector: black
– Ensures ATA/66/100/133 hard drive installed on the
primary IDE channel

Figure 6-37 The primary IDE channel connector is often color-coded as blue

A+ Guide to Managing & Maintaining Your 38

© Cengage Learning 2014
PC, 8th Edition

19
 9/22/2016

Steps to Configure and Install a Parallel

ATA Drive
• Step 1: Open case, decide how to configure drives
• Step 2: Set the jumpers on the drive

Figure 6-38 A PATA drive most

likely will have diagrams of jumper
settings for master and slave
options printed on the drive housing

A+ Guide to Managing & Maintaining Your 39

© Cengage Learning 2014
PC, 8th Edition

Table 5-4 Jumper settings on a parallel ATA hard drive

Figure 6-39 Jumper settings on a hard drive and their meanings

A+ Guide to Managing & Maintaining Your 40

© Cengage Learning 2014
PC, 8th Edition

20
 9/22/2016

Steps to Configure and Install a Parallel

ATA Drive
• Step 3: Mount the drive in the bay
– Decide whether to connect data cable before or after
inserting bay inside the computer case
• Then install drive in bay and connect the cable in
whichever order works best
– Connect data cable to IDE connector on motherboard
– Install a power connection to each drive
– Before replacing case cover verify installation

A+ Guide to Managing & Maintaining Your 41

© Cengage Learning 2014
PC, 8th Edition

Setting Up Hardware RAID

• RAID (Redundant Array of Inexpensive Disks)

– Also: Redundant Array of Independent Disks
– A technology that configures two or more hard drives
to work together as an array of drives
• Why use RAID?
– To improve fault tolerance by writing two copies of it,
each to a different hard drive
– To improve performance by writing data to two or
more hard drives to that a single drive is not
excessively used

A+ Guide to Managing & Maintaining Your 42

© Cengage Learning 2014
PC, 8th Edition

21
 9/22/2016

Types of RAID

• Spanning – sometimes called JBOD (just a bunch of

disks)
– Uses two hard drives to hold a single Windows
volume
– When one drive is full, data is written to second drive
• RAID 0 – uses two or more physical disks
– Writes to physical disks evenly across all disks so that
no one disk receives all activity
– Windows calls RAID 0 a striped volume

A+ Guide to Managing & Maintaining Your 43

© Cengage Learning 2014
PC, 8th Edition

Types of RAID

• RAID 1: Mirroring
– Duplicates data on one drive to another drive and is
used for fault tolerance (mirrored volume)
• RAID 5: uses three or more drives
– Stripes data across drives and uses parity checking
– Data is not duplicated
• RAID 10: RAID 1+0 (pronounced RAID one zero)
– Combination of RAID 1 and RAID 0
– Takes at least 4 disks

A+ Guide to Managing & Maintaining Your 44

© Cengage Learning 2014
PC, 8th Edition

22
 9/22/2016

How to Implement Hardware RAID

• Hardware implementation
– Hardware RAID controller or RAID controller card
• Motherboard does the work, Windows unaware of
hardware RAID implementation
• Software implementation uses operating system
• Best RAID performance
– All hard drives in an array should be identical in
brand, size, speed, other features
• If Windows installed on a RAID hard drive RAID
must be implemented before Windows installed

A+ Guide to Managing & Maintaining Your 45

© Cengage Learning 2014
PC, 8th Edition

Figure 6-45 RAID controller card

provides four SATA internal
connectors

A+ Guide to Managing & Maintaining Your 46

© Cengage Learning 2014
PC, 8th Edition

23
 9/22/2016

How to Implement Hardware Raid

• General directions to install RAID 5 array using
three matching SATA drives
– Install drives in the computer case and connect each
to motherboard
– Boot system and enter BIOS setup
• Verify drives recognized, select option to configure
SATA, and select RAID
– Reboot the system
• Press Ctrl and I to enter the RAID configuration utility
– Select option 1 to “Create RAID Volume”
• Select RAID 5 (Parity), stripe size value, volume size
• Create volume
A+ Guide to Managing & Maintaining Your 47
© Cengage Learning 2014
PC, 8th Edition

Figure 6-47 Configure SATA ports on Figure 6-48 BIOS utility to configure a RAID
the motherboard to enable RAID array

A+ Guide to Managing & Maintaining Your 48

© Cengage Learning 2014
PC, 8th Edition

24
 9/22/2016

Figure 6-49 Make your choices for the RAID array

A+ Guide to Managing & Maintaining Your 49

© Cengage Learning 2014
PC, 8th Edition

About Tape Drives and Floppy Drives

• Tape drives can use a SATA, PATA, or SCSI

interface
• As a technician, you may be called on to support old
floppy drives
• Both tape drives and floppy drives are covered in
this section

A+ Guide to Managing & Maintaining Your 50

© Cengage Learning 2014
PC, 8th Edition

25
 9/22/2016

Installing Tape Drives and Selecting

Tape Media
• Tapes drives – an inexpensive way of backing up a
hard drive
• WORM (write once read many) – assures data
written will not be deleted or overwritten
• Disadvantage: data is stored by sequential access
– To read data from anywhere on the tape, you must
start at the beginning of the tape and read until you
find the data you want
– Slow and inconvenient

A+ Guide to Managing & Maintaining Your 51

© Cengage Learning 2014
PC, 8th Edition

Installing Tape Drives and Selecting

Tape Media
• Two kinds of tapes:
– Full-sized data cartridges
– Minicartridges
• More popular because their drives can fit into a
standard 3-inch drive bay of a PC case
• When selecting a tape drive, consider:
– How many and what type of cartridges the drive can
use
– How it interfaces with the computer
• External drives can connect to a computer using a
USB, FireWire, SCSI, SAS, or eSATA port
A+ Guide to Managing & Maintaining Your 52
© Cengage Learning 2014
PC, 8th Edition

26
 9/22/2016

Installing a Floppy Drive

• Floppy disk drive (FDD)

– 3 ½” floppy disk format
– Holds only 1.44 MB of data
– Floppy drive subsystem
• Floppy drive, ribbon cable, power cable, connections
• Today’s floppy drive cables have a connector at each
end to accommodate a single drive
• Older cables have an extra connector or two in the
middle of the cable for a second floppy drive

A+ Guide to Managing & Maintaining Your 53

© Cengage Learning 2014
PC, 8th Edition

Installing a Floppy Drive

• Install the drive in a bay as you would a hard drive
• Connect floppy drive data cable and power cord to
motherboard
– If you connect the cable the wrong way, the drive light
will stay lit and will not work
– Be sure the end of the cable with the twist connects to
the drive and the other end to the motherboard
• Replace cover, turn on computer, and enter BIOS
setup to verify installation

A+ Guide to Managing & Maintaining Your 54

© Cengage Learning 2014
PC, 8th Edition

27
 9/22/2016

Summary

• A hard disk drive (HDD) comes in 3.5” for desktop

and 2.5” for laptops
• A hard drive can be magnetic, solid-state, or hybrid
• Most hard drives use the ATA interface standards
• Two ATA categories are parallel ATA and serial ATA
• S.M.A.R.T is a self-monitoring technology whereby
the BIOS monitors the health of a hard drive
• SCSI interface standards include narrow and wide
SCSI and can use a variety of cables and
connectors
A+ Guide to Managing & Maintaining Your 55
© Cengage Learning 2014
PC, 8th Edition

Summary
• When selecting a hard drive, consider storage
capacity, technology, spindle speed, interface
standard, and buffer size
• SATA drives require no configuration and are
installed using a power cord and a data cable
• PATA drives require you to set a jumper to
determine if the drive will be the single drive, master,
or slave on a single cable
• RAID technology uses an array of hard drives to
provide fault tolerance and/or improvement in
performance

A+ Guide to Managing & Maintaining Your 56

© Cengage Learning 2014
PC, 8th Edition

28
 9/22/2016

Summary

• Hardware RAID is implemented using the

motherboard BIOS or a RAID controller card
• Software RAID is implemented in Windows
• Tape drives are an inexpensive way to back up an
entire hard drive or portions of it
• Today’s floppy disks are 3.5” high-density disks that
hold 1.44 MB of data
• After a floppy disk drive is installed, you must
configure the drive in BIOS setup

A+ Guide to Managing & Maintaining Your 57

© Cengage Learning 2014
PC, 8th Edition

29