Universal Input Indicator

DP70
Optional Analog Output

WISCO DP70 Manual V2.0 Page I

Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900

Tel (662)591-1916, (662)954-3280-1, Fax (662)580-4427, www.wisco.co.th, E-mail [email protected]

Page II WISCO DP70 Manual V2.0

บริษัท วิศณุและสุภัค จากัด 102/111-112 หมู่บ้านสินพัฒนาธานี ถนนเทศบาลสงเคราะห์ แขวงลาดยาว เขตจตุจกั ร กรุงเทพฯ 10900
โทร. (02)591-1916, (02)954-3280-1, แฟกซ์ (02)580-4427, www.wisco.co.th, อีเมล์ [email protected]
 สารบัญ
Universal Input Indicator ............................................................... 1

I. Example of application ................................................................... 2

II. Wiring diagram .............................................................................. 2

III. setting ............................................................................................ 3

1. Menu Input Type ............................................................................ 5

2. Menu Scale ..................................................................................... 7

3. Menu Analog Output ....................................................................... 8

4. Menu Alarm ................................................................................... 10

5. Menu Calibrate .............................................................................. 12

WISCO DP70 Manual V2.0 Page III

Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900

Tel (662)591-1916, (662)954-3280-1, Fax (662)580-4427, www.wisco.co.th, E-mail [email protected]

Page IV WISCO DP70 Manual V2.0

บริษัท วิศณุและสุภัค จากัด 102/111-112 หมู่บ้านสินพัฒนาธานี ถนนเทศบาลสงเคราะห์ แขวงลาดยาว เขตจตุจกั ร กรุงเทพฯ 10900
โทร. (02)591-1916, (02)954-3280-1, แฟกซ์ (02)580-4427, www.wisco.co.th, อีเมล์ [email protected]
 Universal Input Indicator
DP70

- 5 Digits Display
- Programmable Input type
- 2 Alarm Relay
- 1 Analog output or RS485
(Option)

Universal Input Indicator is panel meter with programmable input. It has

5 digit and 2 set of alarm (Hi/Low). Moreover there is optional for analog output
Specifications
Serial Communication Digital Channel: 2 Channels (Alarm)
Interface: RS-485 (Modbus) Optional Digital Type: Relay Contact
Protocol: MODBUS (ASCII, RTU), Wisco (250 VAC@5 A)
ASCII Output Impedance:
Monitor Current Max load 800 Ω
Display: 5 digits, Red LED (7-Segment) Voltage Min load 1000 Ω
Input Power Requirements
Number of channel: 1 Channel Power Supply: 110, 220 VAC (12 VDC, 24
ADC Resolution: 24 bits VDC Optional)

Input type: Programmable Environmental Limits

Input range: Operating Temperature: 0 to 55 °C
Thermocouple (R, S, K, E, J, T, B) Operating Humidity: 5 to 95% RH
RTD (Cu10, PT100, PT1000) Storage Temperature: 0 to 70 °C
Resistance (0-600 Ω, 0-1200 Ω, 0-4000 Ω) Physical Characteristics
Voltage mVDC (0 to 80, 0 to 150 mVDC) Dimension: W96 x H48 x D120 mm.
Voltage (0 to 1, 0 to 5, 0 to 10, 0 to 30 VDC) Mounting: Panel Flush Mounting
Current (4 to 20, 0 to 20, 0 to 40 mA) Wiring: Screw terminals
Accuaracy: ± 1 least significant digit Warranty
Output Warranty Period: 5 year
Number of channel: 1 Channel
Output type: Current, Voltage (Optional)
Output range:
Current (0 to 20, 4 to 20 mA)
Voltage (0 to 1, 0 to 5, 0 to 10 VDC)

WISCO DP70 Manual V2.0 Page 1 of 13

Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900

Tel (662)591-1916, (662)954-3280-1, Fax (662)580-4427, www.wisco.co.th, E-mail [email protected]

I. Example of application

Input Alarm Output

Pressure
Transmitter

Analog Output

Data Logger

II. Wiring diagram

2 Wire 5
X +24 14 Display
+ AL1
3
15
I V 4
A/D
16
- 24 Bit
8
17 MCU
6
AL2
13
Jump for mA 7
12
11 +
L(+) 1 Voltage
SUPPLY -
N(-) 2
220 VAC
AMP 10
-
Current
RS485 9 +

A
15 15 15 15
V
16 16 B 16 16
TC mV/Volt mA R Shunt
17 17 B 17 17
RTD POT

Page 2 of 13 WISCO DP70 Manual V2.0

บริษัท วิศณุและสุภัค จากัด 102/111-112 หมู่บ้านสินพัฒนาธานี ถนนเทศบาลสงเคราะห์ แขวงลาดยาว เขตจตุจักร กรุงเทพฯ 10900
โทร. (02)591-1916, (02)954-3280-1, แฟกซ์ (02)580-4427, www.wisco.co.th, อีเมล์ [email protected]
III. Setting Menu
Mode 3
Mode

Input Type TC R,S,K,E,J,T,B Exit

Mode Exit

RTD Cu10,Pt100,Pt1,000 Exit

Mode Exit

R(Ohm) 600,1200,4000 Exit

Mode Exit

Mode

mV 0-80,0-150 Exit

Mode Exit

V 0-1,0-5,0-10,0-30 Exit

Mode Exit

mA 4-20,0-20,0-40 Exit

Mode Exit

Scale Display 0,1,2,3,4, Exit

Mode Exit

High Value Max Rang Exit

Mode Exit
Mode

Low Value Min Rang Exit

Mode

1 2

WISCO DP70 Manual V2.0 Page 3 of 13

Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900

Tel (662)591-1916, (662)954-3280-1, Fax (662)580-4427, www.wisco.co.th, E-mail [email protected]

 1 2

Analog Output High Value Max Rang Exit

Mode Exit

Mode Low Value Min Rang Exit

Mode

Alarm 1 Level High, Low Exit

Mode Exit

Set point Parameter Exit

Mode

Mode Exit

Hysteresis Parameter Exit

Mode

Alarm 2 Level High, Low Exit

Mode Exit

Set point Parameter Exit

Mode

Mode Exit

Hysteresis Parameter Exit

Mode

Exit the menu by hold Exit button for 3 second

Page 4 of 13 WISCO DP70 Manual V2.0

บริษัท วิศณุและสุภัค จากัด 102/111-112 หมู่บ้านสินพัฒนาธานี ถนนเทศบาลสงเคราะห์ แขวงลาดยาว เขตจตุจักร กรุงเทพฯ 10900
โทร. (02)591-1916, (02)954-3280-1, แฟกซ์ (02)580-4427, www.wisco.co.th, อีเมล์ [email protected]
 Setting Menu for DP70
1. Menu Input Type
Input Type

Mode Mode Mode Mode Mode

Thermocouple RTD R (Ohm) mV Voltage Current

Menu Input Type is for setting type of input. DP70 has 6 type of input which
is Thermocouple, RTD, R (Ohm), mV, Voltage and Current as detail below
 Thermocouple Input

Thermocouple

Type R Type S Type K Type E Type J Type T Type B

Set up Thermocouple Input push Mode button for 3 second then choose

using to choose for thermocouple then using to

select thermocouple type R, S, K, E, J, T, and B. click on Exit button to go the
next step.
RTD Input

RTD

CU 10 PT 100 PT 1000

Set up RTD Input push Mode for 3 second then choose click Mode

then select then using button to select type of RTD which is Cu10,
PT100, PT1000 then click Exit button to go to the next step.
 R (Ohm) Input

R (Ohm)

600 Ω 1200 Ω 4000 Ω

Setting R (Ohm) Input by click Mode button and hold for 3 second then

setting menu will appear click on mode button to select for

input then click to select type of desire input which are Type 600 Ω, 1200
Ω, 4000 Ω then click on Exit button to go to the next step.

WISCO DP70 Manual V2.0 Page 5 of 13

Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900

Tel (662)591-1916, (662)954-3280-1, Fax (662)580-4427, www.wisco.co.th, E-mail [email protected]

  mV Input
mV

0-80 mV 0-150 mV
Setting mV Input by click Mode button and hold for 3 second to go setting

menu then select to choose input type. Click on Mode button to select

for mV input. Use button to choose mV type which is 0-80 mV,

0-150 mV then click on Exit button to go to the next step.
 Voltage Input
Voltage

0-1 VDC 0-5 VDC 0-10 VDC 0-30 VDC

Set up Voltage Input click Mode button and hold for 3 second to go to

setting menu then select to choose input type. Click on mode button

to select for Voltage input. Use button to choose Voltage input

type which is 0-1, 0-5, 0-10, 0-30 VDC then click on Exit button to go to the
next step
 Current Input
Current

4-20 mA 0-20 mA 0-40 mA

Set up Current Input click Mode button and hold for 3 second to getting in

to setting menu then select to choose input type. Click on mode

button to select for Current input. Use to select type of Current

input which is 4-20, 0-20, 0-40 mA then click on Exit button to go to the next
step.

Page 6 of 13 WISCO DP70 Manual V2.0

บริษัท วิศณุและสุภัค จากัด 102/111-112 หมู่บ้านสินพัฒนาธานี ถนนเทศบาลสงเคราะห์ แขวงลาดยาว เขตจตุจักร กรุงเทพฯ 10900
โทร. (02)591-1916, (02)954-3280-1, แฟกซ์ (02)580-4427, www.wisco.co.th, อีเมล์ [email protected]
2. Menu Scale

Scale

Mode Mode

Display Hi Value Low Value

Menu Scale is use for calibrate display scale and set up display digit.
 Display

Display

0 0.0 0.00 0.000 0.0000

Display menu is for set up display digit by click Mode button and hold for 3

second to go to setting menu and the select use Mode button to

select and use to select digit type. Clcik Exit button to go to the
next step.

 Hi Value
Hi Value is for set maximum value of the scale.
Click Mode button and hold for 3 second and then
Hi Value
select use choose then use
to select maximum desire value. Click Exit to go to
the next step

Function of each button in Hi Value mode:

 to increase
Mode
 to decrease

 changing position

WISCO DP70 Manual V2.0 Page 7 of 13

Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900

Tel (662)591-1916, (662)954-3280-1, Fax (662)580-4427, www.wisco.co.th, E-mail [email protected]

  Low Value
Low Value is for minimum scale setting. Click Mode
Low Value button and hold for 3 second to get in to setting menu
then select on use Mode button to select
then set minimum desired value by click
Click Exit button to go to the next step
Function for each button in low value mode:
 increase value
Mode
 decrease value
 change position
Example DP70
Input type 4-20 mA and display on panel as 0-100. So, Hi =100 and Low
=0
Input = 4 mA Show 0
Input = 20 mA show 100

3. Menu Analog Output

Com Port

Mode

Hi Value Low Value

Menu Analog Output set up value of analog Output (Optional Analog Output)

 Hi Value
Hi Value is for setting maximum value of Output. Click
Hi Value
Mode button and hold for 3 second. Select and
use button to select click on button to set
maximum desired value. Click Exit to go to next step

Function of each button on Hi Value mode:

 Increase
Mode
 Decrease
 change position

Page 8 of 13 WISCO DP70 Manual V2.0

บริษัท วิศณุและสุภัค จากัด 102/111-112 หมู่บ้านสินพัฒนาธานี ถนนเทศบาลสงเคราะห์ แขวงลาดยาว เขตจตุจักร กรุงเทพฯ 10900
โทร. (02)591-1916, (02)954-3280-1, แฟกซ์ (02)580-4427, www.wisco.co.th, อีเมล์ [email protected]
  Low Value
Low Value is for setting maximum value of Output.
Low Value
Click Mode button and hold for 3 second. Select

and use Mode button to choose then set

minimum desired value by click button. Click Exit to

go to the next step
Function of each button on Low Value mode:

 Increase value

Mode
 Decrease value

 changing position
Example DP70 Input Type is RTD (PT100) set up Input range as 0-200. Hi
= 200 and Low = 0
Input = 0 °C Output = 4 mA
Input = 200 °C Output = 20 mA

WISCO DP70 Manual V2.0 Page 9 of 13

Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900

Tel (662)591-1916, (662)954-3280-1, Fax (662)580-4427, www.wisco.co.th, E-mail [email protected]

4. Menu Alarm
Alarm 1

Mode Mode Mode Mode

Alarm Mode Set Point Hysteresis Alarm Mode Set Point Hysteresis

Menu Alarm is for set up alarm mode

 Alarm Mode
Alarm Mode is setup by click on Mode button for
Alarm Mode
3 second and click or to in order

to set alarm1 or alarm1 click then choose

High Low
and then set mode by click on Click on
the Exit button to go to the next step

 Set Point
Set Point is setting alarm value. Click on Mode button
Set Point
for 3 second then choose or and then

click mode button and choose and set value by

click . Click on Exit button to go to the next step

Function of set point mode

 Increase value

Mode
 Decrease value

 Position Change

Page 10 of 13 WISCO DP70 Manual V2.0

บริษัท วิศณุและสุภัค จากัด 102/111-112 หมู่บ้านสินพัฒนาธานี ถนนเทศบาลสงเคราะห์ แขวงลาดยาว เขตจตุจักร กรุงเทพฯ 10900
โทร. (02)591-1916, (02)954-3280-1, แฟกซ์ (02)580-4427, www.wisco.co.th, อีเมล์ [email protected]
  Hysteresis
Hysteresis would be setup by Click on Mode button
Hysteresis
and hold for 3 second then select or

click on Mode button and choose

then set up desire value by click . Click on Exit

button to go to the next step
Function of Hysteresis mode

 Increase value

Mode
 Decrease value

 Position Change

Example: Input Type is 4-20 mA and display value 0-100

Alarm 1 set as High, Set Point = 80 and Hysteresis = 2
Alarm 1 is on when value is more than 80 and alarm 1 is off when value is
(80-2) = 78
Alarm 2 set as low Set Point = 30 and Hysteresis = 1
Alarm 2 is on when value is lower than 30 and alarm 2 is off when value is
(30+1) = 31

WISCO DP70 Manual V2.0 Page 11 of 13

Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900

Tel (662)591-1916, (662)954-3280-1, Fax (662)580-4427, www.wisco.co.th, E-mail [email protected]

5. Menu Calibrate
Calibrate Input Zero Mode Span Mode Bias Mode

Exit Exit

Mode Exit

Output Zero Span Mode

Exit

Mode Exit

Click on and hold for 3 second to login to calibration mode

Bias Revise Offset value on Y Axis, Shift graph up and down
Span Set up Max scale of Input/Output
Zero Set up min scale of Input/Output
 Calibrate of Input
Input Zero Mode Span Mode Bias

Exit Exit

Click on and hold for 3 second to login to calibration mode then choose

and Click
 Calibrate Zero turns on the minimum power. Minimum input will

show on display and setup by click until get desire value an

then click Exit for save and go to the next step
 Calibrate Span turns on the maximum power. Display will show the

maximum input then adjust by click then click Exit for save
and go to the next step
 Calibrate Bias is for set offset value for all input. Turn on the power

and click to adjust offset value then click Exit value to save
and go to the next step.

Page 12 of 13 WISCO DP70 Manual V2.0

บริษัท วิศณุและสุภัค จากัด 102/111-112 หมู่บ้านสินพัฒนาธานี ถนนเทศบาลสงเคราะห์ แขวงลาดยาว เขตจตุจักร กรุงเทพฯ 10900
โทร. (02)591-1916, (02)954-3280-1, แฟกซ์ (02)580-4427, www.wisco.co.th, อีเมล์ [email protected]
  Calibrate of Output
Output Zero Span

Exit

Measurement equipment will be needed for calibrate output such as multi

meter etc.

In order to calibrate output, Click button and hold for 3 second to login

to calibration mode then choose and click to select revise function

 Calibrate Zero turns on the minimum power. Minimum input will
show on display and reading output by multi meter then setup by

click until get desire value for output an then click Exit for
save and go to the next step
 Calibrate Span turns on the maximum power. Display will show the
maximum input and multi meter will show maximum output then

adjust by click until got desired output then click Exit for
save and go to the next step

P.S. Display panel show only value of input. In order to display analog
output, multi meter would be needed.

Edit: 25/03/2013

WISCO DP70 Manual V2.0 Page 13 of 13

Wisnu and Supak Co., Ltd 102/111-112 Tessabansongkroh Rd., Ladyao, Jatujak, Bangkok 10900

Tel (662)591-1916, (662)954-3280-1, Fax (662)580-4427, www.wisco.co.th, E-mail [email protected]